KV-85
AMD Athlon 64 System Board
Socket 754
User’s Manual
Rev. 1.01
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1. Introduction ..........................................................................1-1
Chapter 3. BIOS Setup............................................................................3-1
3-10. Set User Password..................................................................................3-20
3-11. Save & Exit Setup..................................................................................3-20
3-12. Exit Without Saving...............................................................................3-20
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-1. Setup Items...............................................................................................4-2
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
1-1
Chapter 1. Introduction
1-1. Features & Specifications
1. CPU
•
•
Supports AMD Socket 754 Athlon 64/Sempron Processor with 1600MHz Hyper-Transport
Supports AMD K8 CPU Cool ‘n’ Quiet Technology
2. Memory
•
•
•
2 x 184-pin DIMM sockets
Supports DDR400/333 Un-buffered ECC/ Non-ECC memory
Supports maximum memory capacity up to 2GB
3. Chipset
•
VIA K8M800 + VT8237R
4. Graphics
•
Integrated UniChrome Pro Graphics with 2D/3D/Video controller
5. SATA RAID
•
•
Serial ATA 1.5Gb/s data transfer rate
Supports SATA RAID 0/1
6. LAN
•
On board 10/100M PHY
7. Audio
•
Onboard 5.1-channel Audio CODEC
8. Internal I/O Connectors
•
•
•
•
•
•
•
•
1x AGP 8X slot
3x PCI slots
1x Floppy port supports up to 2.88MB
2x Ultra DMA 133/100/66/33 connectors
2x Serial ATA 1.5Gb/s connectors
2x USB 2.0 headers
1x CD-IN
1x FP-Audio header
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2
Chapter 1
9. Back Panel I/O
•
•
•
•
•
•
1x PS/2 keyboard, 1x PS/2 mouse
1x Parallel Port, 1x Serial Port,
1x VGA Connector
4x USB 2.0 Connectors
1x RJ-45 LAN Connector
1x Audio connector (Line-out, Line-in, MIC-in)
10. Miscellaneous
mATX form factor: 244 x 244 mm
•
ꢀ
Specifications and information contained herein are subject to change without notice.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
1-4
Chapter 1
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Setup
2-1
Chapter 2. Hardware Setup
Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or
disconnect the power cord before installing or unplugging any connectors or add-on cards. Failing to do
so may cause the motherboard components or add-on cards to malfunction or damaged.
2-1. Install The Motherboard
Most computer chassis have a base with many mounting holes to allow motherboard to be securely
attached on and at the same time, prevented from short circuits. There are two ways to attach the
motherboard to the chassis base:
1. use with studs
2. or use with spacers
In principle, the best way to attach the board is to
use with studs. Only if you are unable to do this
should you attach the board with spacers. Line up
the holes on the board with the mounting holes on
the chassis. If the holes line up and there are
screw holes, you can attach the board with studs.
If the holes line up and there are only slots, you
can only attach with spacers. Take the tip of the
spacers and insert them into the slots. After doing
this to all the slots, you can slide the board into
position aligned with slots. After the board has been positioned, check to make sure everything is OK
before putting the chassis back on.
ATTENTION: To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they
are already fastened on the chassis base and are without mounting-holes on the motherboard to align with.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2
Chapter 2
2-2. Install CPU, Heatsink and Fan Assembly
Please pay attention to the following notices
before installing the CPU and heatsink/fan
assembly.
1. Always use the processor with the
Heatsink and Fan Assembly installed.
2. Do not touch the pins on the processor.
3. If you ever need to reinstall the Heatsink
and fan Assembly, please clean the
heatsink surface and apply new thermal
interface material first.
3. Lower the locking lever to the fully locked
position.
1. Pull out the socket locking lever slightly,
then lift it up.
4. Apply thermal interface material.
2. Align the corner with triangle mark of the
processor with the marking on the motherboard,
and then place the processor vertical down into
the socket.
5. Place the heatsink and fan assembly onto
the retention frame. Match the heatsink clip
with the socket mounting lug. Hook the spring
clip to the mounting lug.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Setup
2-3
6. On the other side, push the retention clip
straight down to lock into the plastic lug on the
retention frame.
7. Turn the cam lever to lock into the retention
frame.
8. Attach the four-pin power plug from the
heatsink and fan assembly to the CPU FAN
connector.
For detailed information on how to install your
heatsink and fan assembly, please refer to the
instruction manual came packed with the
heatsink and fan assembly you bought.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-4
Chapter 2
2-3. Install System Memory
This system board provides two 184-pin DDR DIMM slots for DDR400 memory modules with memory
expansion size up to 2GB.
Bank
Memory Module
256MB, 512MB, 1GB
256MB, 512MB, 1GB
Total Memory
256MB ~ 1GB
256MB ~ 1GB
256MB ~ 2GB
Bank 0, 1 (DIMM1)
Bank 2, 3 (DIMM2)
Total System Memory
NOTE: Usually there is no hardware or BIOS setup require after adding or removing memory modules,
but you will have to clear the CMOS memory first if any memory module related problem occurs.
Power off the computer and unplug the AC power cord before installing or removing memory modules.
1. Locate the DIMM slot on the board.
2. Hold two edges of the DIMM module
carefully, keep away of touching its
connectors.
3. Align the notch key on the module with the
rib on the slot.
4. Firmly press the module into the slots until
the ejector tabs at both sides of the slot
automatically snaps into the mounting notch.
Do not force the DIMM module in with extra
force as the DIMM module only fit in one direction.
5. To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and
then pull out the DIMM module.
ATTENTION: Static electricity can damage the electronic components of the computer or optional
boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a
grounded metal object briefly.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Setup
2-5
2-4. Connectors, Headers and Switches
Here we will show you all of the connectors, headers and switches, and how to connect them. Please read
the entire section for necessary information before attempting to finish all the hardware installation inside
the computer chassis. A complete enlarged layout diagram is shown in Chapter 1 for all the position of
connectors and headers on the board that you may refer to.
WARNING: Always power off the computer and unplug the AC power cord before adding or removing
any peripheral or component. Failing to so may cause severe damage to your motherboard and/or
peripherals. Plug in the AC power cord only after you have carefully checked everything.
(1). ATX Power Input Connectors
This motherboard provides two power connectors to connect to an ATX12V power supply.
NOTE: It is recommended to connect to a power supply with 350W, 20A +5VDC capacity at least for
heavily loaded system, and 2A +5VSB capacity at least for supporting wake-up features.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-6
Chapter 2
(2). FAN Connectors
These 3-pin connectors each provide power to the cooling fans installed in your system.
The CPU must be kept cool by using a powerful fan with heatsink. The system is capable of monitoring
the speed of the CPU fan.
•
•
CPUFAN1: CPU Fan Power Connector
CASFAN1: Auxiliary Fan Power Connector
WARNING: These fan connectors are not jumpers. DO NOT place jumper caps on these connectors.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Setup
2-7
(3). CMOS Memory Clearing Header
This header uses a jumper cap to clear the CMOS memory.
•
•
Pin 1-2 shorted (default): Normal operation.
Pin 2-3 shorted: Clear CMOS memory.
WARNING: Turn the power off first (including the +5V standby power) before clearing the CMOS
memory. Failing to do so may cause your system to work abnormally or malfunction.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-8
Chapter 2
(4). Front Panel Switches & Indicators Headers
These headers are used for connecting switches and LED indicators on the chassis front panel.
Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below
stands for positive polarity for the LED connection. Please pay attention to connect these headers. A
wrong orientation will only cause the LED not lighting, but a wrong connection of the switches could
cause system malfunction.
•
•
•
•
•
SJ1:
Connects to ACPI LED cable of chassis front panel.
SPK1:
Connects to the System Speaker cable of chassis.
HDDLED (Pin 1, 3):
Connects to the HDD LED cable of chassis front panel.
RST (Pin 5, 7):
Connects to the Reset Switch cable of chassis front panel.
MSGLED (Pin 2, 4):
Connecting pins 2 and 4 to a single or dual color front panel mounted LED provides power on/off,
sleep, and message waiting indication.
•
PWR (Pin 6, 8):
Connects to the Power Switch cable of chassis front panel.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Setup
2-9
(5). Additional USB Port Headers
These headers each provide 2 additional USB 2.0 ports connection through an USB cable designed for
USB 2.0 specifications.
Pin
1
Pin Assignment
VCC
Pin
2
Pin Assignment
VCC
3
Data0 -
Data0 +
Ground
NC
4
Data1 -
Data1 +
Ground
NC
5
6
7
8
9
10
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-10
Chapter 2
(6). Front Panel Audio Connection Header
This header provides the connection to audio connector at front panel.
•
To use the audio connector at front panel, remove all the jumpers on this header, and then connect
to front panel by the extension cable provided with the chassis.
•
To use the audio connector at rear panel, disconnect the extension cable, attach the jumpers back at
pin 5-6, and pin 9-10 (default setting).
Pin
1
Pin Assignment
Audio Mic.
Pin
2
Pin Assignment
Ground
3
Audio Mic. Bias
4
VCC
Speaker Out Right
Channel
Speaker Out Right
Channel Return
5
7
9
6
8
X
NC
Speaker Out Left
Channel
Speaker Out Left
Channel Return
10
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
2-12
Chapter 2
(8). Accelerated Graphics Port Slot
This slot supports an optional AGP graphics card up to AGP 8X mode.
ATTENTION: This motherboard does not support 3.3V AGP cards. Use only 1.5V or 0.8V AGP cards.
(9). Internal Audio Connectors
These connectors connect to the audio output of internal CD-ROM drive or add-on card.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Setup
2-13
(10). Floppy and IDE Disk Drive Connectors
The FDC1 connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable. Connect
the single end at the longer length of ribbon cable to the FDC1 on the board, the two connectors on the
other end to the floppy disk drives connector. Generally you need only one floppy disk drive in your
system.
NOTE: The red line on the ribbon cable must be aligned with pin-1 on both the FDC1 port and the floppy
connector.
Each of the IDE port connects up to two IDE drives at
Ultra ATA/100 mode by one 40-pin, 80-conductor, and
3-connector Ultra ATA/66 ribbon cables.
Connect the single end (blue connector) at the longer
length of ribbon cable to the IDE port of this board, the
other two ends (gray and black connector) at the shorter
length of the ribbon cable to the connectors of your hard
drives.
NOTE: Make sure to configure the “Master” and “Slave” relation before connecting two drives by one
single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and
the hard-drive connector.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-14
Chapter 2
(11). Back Panel Connectors
•
•
•
•
Mouse: Connects to PS/2 mouse.
Keyboard: Connects to PS/2 keyboard.
LPT1: Connects to printer or other devices that support this communication protocol.
COM1: Connects to external modem, mouse or other devices that support this communication
protocol.
•
•
•
VGA1: Connects to monitor input.
LAN: Connects to Local Area Network.
USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse,
keyboard, hub, digital camera, joystick etc.
•
JS1:
Line-In: Connects to the line out from external audio sources.
Line-Out: Connects to the front left and front right channel in the 5.1-channel or regular 2-channel
audio system.
Mic-In: Connects to the plug from external microphone.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup
3-1
Chapter 3. BIOS Setup
This motherboard provides a programmable EEPROM that you can update the BIOS utility. The BIOS
(Basic Input/Output System) is a program that deals with the basic level of communication between
processor and peripherals. Use the BIOS Setup program only when installing motherboard, reconfiguring
system, or prompted to “Run Setup”. This chapter explains the Setup Utility of BIOS utility.
After powering up the system, the BIOS message appears on the screen, the memory count begins, and
then the following message appears on the screen:
PRESS DEL TO ENTER SETUP
If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt> + <Del>
keys, or by pressing the Reset button on computer chassis. Only when it failed by these two methods can
you restart the system by powering it off and then back on.
After pressing <Del> key, the main menu screen appears.
Phoenix – AwardBIOS CMOS Setup Utility
► Standard CMOS Features
► Advanced BIOS Features
► Advanced Chipset Features
► Advanced Chipset Features
► Power Management Setup
► PnP/PCI Configurations
► PC Health Status
► Frequency/Voltage Control
Load Fail-Safe Defaults
Load Optimized Defaults
Set User Password
Save & Exit Setup
Exit Without Saving
Esc : Quit
F10 : Save & Exit Setup
↑ ↓ → ← : Select Item
6A7L1A1Z
Time, Date, Hard Disk Type
NOTE: In order to increase system stability and performance, our engineering staffs are constantly
improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual are for
your reference only, and may not completely match with what you see on your screen.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2
Chapter 3
In the BIOS Setup main menu, you can see several options. We will explain these options step by step in
the following pages of this chapter, but let us first see a short description of the function keys you may
use here.
Esc:
Press this button to quit the BIOS Setup.
↑↓← →:
Press these buttons to choose, in the main menu, the option you want to confirm or to modify.
F10:
When you have completed the setup of BIOS parameters, press this button to save these parameters and
to exit the BIOS Setup menu.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup
3-3
3-1. Standard CMOS Features
This section contains the basic configuration parameters of the BIOS. These parameters include date,
hour, VGA card, FDD, and HDD settings.
Phoenix – Award WorkstationBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Thu. Jan 1 2005
12 : 34 : 56
Item Help
► IDE Channel 1 Master
► IDE Channel 1 Slave
► IDE Channel 2 Master
► IDE Channel 2 Slave
► IDE Channel 3 Master
► IDE Channel 4 Master
None
None
None
None
None
None
Drive A
Drive B
Halt On
1.44M, 3.5 in.
None
All, But keyboard
Base Memory
Extended Memory
Total Memory
640K
1046520K
1047552K
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Date (mm:dd:yy):
This item sets the date you specify (usually the current date) in the format of [Month], [Date], and [Year].
Time (hh:mm:ss):
This item sets the time you specify (usually the current time) in the format of [Hour], [Minute], and
[Second].
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-4
Chapter 3
ꢁ
IDE Channel 1 Master/Slave, IDE Channel 2 Master/Slave, IDE Channel
3/4 Master:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
IDE Channel 1 Master
Press Enter
IDE HDD Auto-Detection
Item Help
IDE Channel 1 Master
Access Mode
Auto
Auto
Capacity
0 MB
Cylinder
Head
Precomp
Landing Zone
Sector
0
0
0
0
0
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
IDE HDD Auto-Detection:
This item allows you to detect the parameters of IDE drives by pressing <Enter> key. The parameters will
be shown on the screen automatically.
IDE Channel 1 Master/Slave, IDE Channel 2 Master/Slave, IDE Channel 3/4 Master:
When set to [Auto], the BIOS will automatically check what kind of IDE drive you are using. If you want
to define your own drive by yourself, set it to [Manual] and make sure you fully understand the meaning
of the parameters. Please refer to the instruction manual provided by the device’s manufacturer to get the
setting right.
Access Mode:
This item selects the mode to access your IDE devices. Leave this item to its default [Auto] setting to
detect the access mode of your HDD automatically.
Capacity:
This item displays the approximate capacity of the disk drive. Usually the size is slightly greater than the
size of a formatted disk given by a disk-checking program.
Cylinder:
This item configures the numbers of cylinders.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup
3-5
Head:
This item configures the numbers of read/write heads.
Precomp:
This item displays the number of cylinders at which to change the write timing.
Landing Zone:
This item displays the number of cylinders specified as the landing zone for the read/write heads.
Sector:
This item configures the numbers of sectors per track.
ꢁ
Back to Standard CMOS Features Setup Menu:
Drive A & Drive B:
This item sets the type of floppy drives (usually only Drive A) installed.
Halt On:
This item determines whether the system stops if an error is detected during system boot-up.
[All Errors]: The system-boot will stop whenever the BIOS detect a non-fatal error.
[No Errors]: The system-boot will not stop for any error detected.
[All, But Keyboard]: The system-boot will stop for all errors except a keyboard error.
[All, But Diskette]: The system-boot will stop for all errors except a diskette error.
[All, But Disk/Key]: The system-boot will stop for all errors except a diskette or keyboard error.
Base Memory:
This item displays the amount of base memory installed in the system. The value of the base memory is
typically 640K for system with 640K or more memory size installed on the motherboard.
Extended Memory:
This item displays the amount of extended memory detected during system boot-up.
Total Memory:
This item displays the total memory available in the system.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-6
Chapter 3
3-2. Advanced BIOS Features
Phoenix – Award WorkstationBIOS CMOS Setup Utility
Advanced BIOS Features
Press Enter
► Hard Disk Boot Priority
Item Help
Quick Power on Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Security Option
Enabled
Floppy
Hard Disk
CDROM
Enabled
Disabled
Disabled
On
Setup
Disabled
Small Logo(EPA) Show
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Hard Disk Boot Priority:
This item selects the hard disks booting priority. By pressing <Enter> key, you can enter its submenu
where the hard disks detected can be selected for the booting sequence to boot up system.
This item functions only when there is the option of [Hard Disk] in any one of the First/Second/Third
Boot Device items.
ꢀ
Bootable Add-in Device:
This item selects the priority of bootable add-in devices.
Quick Power On Self Test:
When set to [Enabled], this item speeds up the Power On Self Test (POST) after powering on the system.
The BIOS shorten or skip some check during the POST.
First Boot Device / Second Boot Device / Third Boot Device / Boot Other Device:
Select the drive to boot first, second and third in the [First Boot Device], [Second Boot Device], and
[Third Boot Device] items respectively. The BIOS will boot the operating system according to the
sequence of the drive selected. Set [Boot Other Device] to [Enabled] if you wish to boot from another
device other than these three items.
Swap Floppy Drive:
When set to [Enabled], and the system is booting from the floppy drive, the system will boot from drive B
instead of the regular drive A. There must be two floppy drives connected in the system to use this
function.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup
3-7
Boot Up Floppy Seek:
When set to [Enabled], the BIOS will check whether the floppy disk drive is installed or not.
Boot Up NumLock Status:
This item determines the default state of the numeric keypad at system booting up.
[On]: The numeric keypad functions as number keys.
[Off]: The numeric keypad functions as arrow keys.
Security Option:
This item determines when the system will prompt for password - every time the system boots or only
when enters the BIOS setup.
[Setup]: The password is required only when accessing the BIOS Setup.
[System]: The password is required each time the computer boots up.
NOTE: Don’t forget your password. If you forget the password, you will have to open the computer case
and clear all information in the CMOS before you can start up the system. But by doing this, you will
have to reset all previously set options.
Small Logo(EPA) Show:
Enables or disables the display of the EPA logo during boot.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-8
Chapter 3
3-3. Advanced Chipset Features
Phoenix – Award WorkstationBIOS CMOS Setup Utility
Advanced Chipset Features
► AGP & P2P Bridge Control
Press Enter
Press Enter
Press Enter
8X
Item Help
► DRAM Clock/Drive Control
► LDT & PCI Bus Control
Vlink Data Rate
Init Display First
PCI Slot
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
ꢁ
AGP & P2P Bridge Control:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
Advanced Chipset Features
AGP Aperture Size
AGP 2.0 Mode
128M
Item Help
4X
AGP Driving Control
X AGP Driving Value
AGP Fast Write
Auto
DA
Disabled
Disabled
Disabled
AGP Master 1WS Write
AGP Master 1WS Read
AGP 3.0 Calibration cycle
Disabled
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
AGP Aperture Size:
This option specifies the amount of system memory that can be used by the AGP device. The aperture is a
portion of the PCI memory address range dedicated for graphics memory address space.
AGP 2.0 Mode:
This item selects the data transfer rate of AGP device. A higher rate delivers faster and better graphics to
your system. Make sure your graphics card supports the mode you select.
AGP Driving Control:
Leave this item to its default setting.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup
3-9
ꢀ
AGP Driving Value:
Leave this item to its default setting.
AGP Fast Write:
Two options are available: Disabled $Enabled. The default setting is Enabled. If your AGP adapter can
support this function, then you can choose Enabled. Otherwise, choose Disabled.
AGP Master 1 WS Write:
Two options are available: Disabled $Enabled. The default setting is Disabled. This implements a
single delay when writing to the AGP Bus. When you set it to Enabled, two-wait states are used by the
system, allowing for greater stability.
AGP Master 1 WS Read:
Two options are available: Disabled $Enabled. The default setting is Disabled. This implements a
single delay when reading to the AGP Bus. When you set it to Enabled, two-wait states are used by the
system, allowing for greater stability.
AGP 3.0 Calibration cycle:
Leave this item to its default setting.
ꢁ
DRAM Clock/Drive Control:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
DRAM Clock/Drive Control
Current CPU Frequency
Current DRAM Frequency
DRAM Clock(Mhz)
Item Help
Auto
Auto
Auto
DRAM Command Rate
DRAM CAS# latency Time
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Current CPU Frequency:
This item will show you the current system front side bus speed.
Current DRAM Frequency:
This item will show you the current DRAM bus speed.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-10
Chapter 3
DRAM Clock (Mhz):
This item sets the DRAM clock of your DRAM module. The system may be unstable or unable to boot up
if your DRAM module does not support the clock you set.
DRAM Command Rate:
When the host (northbridge) locates the desired memory address, it then processes the wait state of
commands.
DRAM CAS# latency Time:
You can select SDRAM CAS (Column Address Strobe) latency time according your SDRAM
specification.
ꢁ
LDT & PCI Bus Control:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
LDT & PCI Control
800mhz
LDT Bus Frequency
PCI Delay Transaction
Item Help
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
LDT Bus Frequency:
This item allows you to select LDT Bus Frequency.
PCI Delay Transaction:
Two options are available: Disabled or Enabled. The default setting is Enabled. The chipset has an
embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support
compliance with PCI specification version 2.2.
ꢁ
Back to Advanced Chipset Features Setup Menu:
Vlink Data Rate:
This item can let you select the Vlink Data Rate between northbridge and southbridge.
Init Display First:
This item selects to initialize AGP or PCI Slot first when the system boots.
[PCI Slot]: When the system boots, it will first initialize PCI.
[AGP]: When the system boots, it will first initialize AGP.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup
3-11
3-4. Integrated Peripherals
Phoenix – Award WorkstationBIOS CMOS Setup Utility
Integrated Peripherals
Press Enter
► OnChip IDE Device
► OnChip PCI Device
► SuperIO Device
Item Help
Press Enter
Press Enter
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
ꢁ
OnChip IDE Device:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
VIA OnChip IDE Device
Onboard SATA Mode Select
IDE
Item Help
IDE DMA transfer access
OnChip IDE1 Controller
OnChip IDE2 Controller
IDE Prefetch Mode
Enabled
Enabled
Enabled
Enabled
Enabled
IDE HDD Block Mode
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Onboard SATA Mode Select:
This item selects the mode of Serial ATA.
IDE DMA transfer access:
This item selects the DMA mode for devices connected through IDE channels.
On-Chip IDE1/IDE2 Controller:
This item allows you to enable or disable the primary (IDE1) and secondary (IDE2) IDE controller. Select
[Disabled] if you want to add a different hard drive controller.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-12
Chapter 3
IDE Prefetch Mode:
Two options are available: Disabled or Enabled. The default setting is Enabled. The onboard IDE drive
interfaces supports IDE prefetching for faster drive accesses. If you install a primary and/or secondary
add-in IDE interface, set this field to Disabled if the interface does not support prefetching.
IDE HDD Block Mode:
Enable this filed if your IDE hard drive support block mode. Block mode enables BIOS to automatically
detect the optimal number of block read and writes per sector that the drive can support and improves the
speed of access to IDE devices.
ꢁ
OnChip PCI Device:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
VIA OnChip IDE Device
Enabled
OnChip Audio Controller
OnChip LAN Controller
-LAN Boot ROM
Item Help
Enabled
Disabled
OnChip USB Controller
-USB 2.0 Support
All Enabled
Enabled
OS
OS
-USB Keyboard Support via
-USB Mouse Support via
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
OnChip Audio Controller:
This option enables or disables the audio controller.
OnChip LAN Controller:
This option enables or disables the LAN controller.
ꢀ
LAN Boot ROM:
This item enables or disables the Boot ROM on LAN controller.
OnChip USB Controller:
This option enables or disables the USB controller.
ꢀ
USB 2.0 Support:
This option enables or disables the USB 2.0 controller.
USB Keyboard Support via:
ꢀ
This item allows you to select [BIOS] for using USB keyboard in DOS environment, or [OS] in OS
environment.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup
3-13
ꢀ
USB Mouse Support via:
This item allows you to select [BIOS] for using USB mouse in DOS environment, or [OS] in OS
environment.
ꢁ
SuperIO Device:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
SuperIO Device
Enabled
3F8/IRQ4
378/IRQ7
ECP
Onboard FDD Controller
Onboard Serial Port
` Onboard Parallel Port
-Parallel Port Mode
-ECP Mode Use DMA
Item Help
3
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Onboard FDD Controller:
This option enables or disables the onboard FDC controller.
Onboard Serial Port:
This item determines which I/O addresses the onboard Serial Port controller will access.
[Auto]: The system automatically select an I/O address for the onboard Serial Port.
[3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3]: Allows you to manually select an I/O address for the
onboard Serial Port.
[Disabled]: Disables the onboard Serial Port.
Onboard Parallel Port:
This item specifies the I/O address used by the parallel port.
[Disabled]: This option prevents the parallel port from accessing any system resources. When the value
of this option is set to [Disabled], the printer port becomes unavailable.
[378/IRQ7]: This option allows the parallel port to use [378/IRQ7] as its I/O port address. The majority
of parallel ports on computer systems use IRQ7 and I/O Port 378H as the standard setting.
[278/IRQ5]: This option allows the parallel port to use [278/IRQ5] as its I/O port address.
[3BC/IRQ7]: This option allows the parallel port to use [3BC/IRQ7] as its I/O port address.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-14
Chapter 3
ꢀ
Parallel Port Mode:
This item specifies the parallel port mode.
[SPP]: (Standard Parallel Port) Allows bi-directional parallel port operation at normal speed.
[EPP]: (Enhanced Parallel Port) Allows bi-directional parallel port operation at maximum speed.
[ECP]: (Extended Capabilities Port) Allows bi-directional parallel port operation at a speed faster than
the normal mode’s data transfer rate.
[ECP+EPP]: Allows parallel port operation at ECP and EPP mode.
[Normal]: Allows the standard parallel port mode to be used.
ꢀ
ECP Mode Use DMA:
This item selects the DMA channel of the parallel port.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup
3-15
3-5. Power Management Setup
Phoenix – Award WorkstationBIOS CMOS Setup Utility
Power Management Setup
Instant-Off
Power Button Function
Restore on AC Power Loss
Item Help
Power Off
AMD K8 Cool’n’Quiet control Auto
Wake Up by PME# of PCI
Wake Up by Ring
Disabled
Disabled
Disabled
0
Wake Up by Alarm
-Date(of Month) Alarm
-Time(hh: mm: ss:) Alarm
0 : 0 : 0
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Power Button Function:
This item selects the method of powering off your system:
[Delay 4 Sec.]: Pushing the power button for more than 4 seconds will power off the system. This will
prevent the system from powering off in case you accidentally hit or pushed the power button.
[Instant-Off]: Pressing and then releasing the power button at once will immediately power off the
system.
PWRON After PWR-Fail:
This item selects the system action after an AC power failure.
[Power Off]: When power returns after an AC power failure, the system’s power remains off. You must
press the Power button to power-on the system.
[Power On]: When power returns after an AC power failure, the system’s power will be powered on
automatically.
[Last State]: When power returns after an AC power failure, the system will return to the state where you
left off before power failure occurs. If the system’s power is off when AC power failure occurs, it will
remain off when power returns. If the system’s power is on when AC power failure occurs, the system
will power-on when power returns.
AMD K8 Cool ’n’ Quiet Control:
This option enables or disables the AMD K8 cool and quiet function.
Wake Up by PME# of PCI:
When set to [Enabled], access to the onboard LAN or a PCI card such as a modem or LAN card will
cause the system to wake up. The PCI card must support the wake up function.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-16
Chapter 3
Wake Up by Ring:
When set to [Enabled], any event affecting from Modem Ring will awaken a system that has been
powered down.
Wake Up by Alarm:
When set to [Enabled], you can set the date and time you would like the Soft-Off PC to power-on in the
“Date (of Month) Alarm” and “Time (hh:mm:ss) Alarm” items. However, if the system is being
accessed by incoming calls or the network (Resume On Ring/LAN) prior to the date and time set in these
items, the system will give priority to the incoming calls or network instead.
ꢀ
Date (of Month) Alarm/ Time (hh:mm:ss) Alarm:
You can set the Date (month) Alarm and Time Alarm (hh:mm:ss). Any event occurring will awaken a
system that has powered down.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup
3-17
3-6. PnP/PCI Configurations
Phoenix – Award WorkstationBIOS CMOS Setup Utility
PnP/PCI Configurations
Auto(ESCD)
Resources Controlled By
x IRQ Resources
Item Help
Press Enter
PCI/VGA Pallete Snoop
Assign IRQ For USB
Disbaled
Enabled
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Resources Controlled By:
This item configures all of the boot and Plug-and-Play compatible devices.
[Auto(ESCD]]: The system will automatically detect the settings.
[Manual]: Choose the specific IRQ resources in the “IRQ Resources” menu.
ꢀ
IRQ Resources:
Click <Enter> key to enter its submenu:
Phoenix – Award WorkstationBIOS CMOS Setup Utility
IRQ Resourses
PCI Device
PCI Device
PCI Device
PCI Device
PCI Device
PCI Device
PCI Device
PCI Device
IRQ-3 assigned to
IRQ-4 assigned to
IRQ-5 assigned to
IRQ-7 assigned to
IRQ-9 assigned to
IRQ-10 assigned to
IRQ-11 assigned to
IRQ-12 assigned to
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
This item sets each system interrupt to either [PCI Device] or [Reserved].
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-18
Chapter 3
PCI/VGA Palette Snoop:
This item determines whether the MPEG ISA/VESA VGA cards can work with PCI/VGA or not.
[Enabled]: MPEG ISA/VESA VGA cards work with PCI/VGA.
[Disabled]: MPEG ISA/VESA VGA cards do not work with PCI/VGA.
Assign IRQ For USB:
Names the IRQ assigned to the USB on your system. Activity of the selected IRQ always awakens the
system.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup
3-19
3-7. PC Health Status
Phoenix – AwardBIOS CMOS Setup Utility
PC Health Status
Disabled
Shutdown Temperature
CPU Core Voltage
DDR Voltage
Item Help
2.5V
3.3V
5.0V
+12V
ATX +3.3V
ATX +5V
ATX +12V
Battery Voltage
System Temperature
CPU Temperature
CPU FAN Speed
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Shutdown Temperature:
This item sets the temperature that would shutdown the system automatically in order to prevent system
overheats.
All Voltages, Fans Speed and Thermal Monitoring:
These unchangeable items list the current status of the CPU and environment temperatures, fan speeds,
and system power voltage.
Frequency/Voltage Control:
This item enables you to set the clock speed and system bus for your system. The clock speed and system
bus are determined by the kind of processor you have installed in your system.
Phoenix – AwardBIOS CMOS Setup Utility
Frequency/Voltage Control
DIMM Voltage Adjust
CPU Clock
2.60V
Item Help
200MHz
↑↓:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
DIMM Voltage Adjust:
This item adjusts the voltage delivered to the DIMM memory.
CPU Clock:
Use the CPU Host Clock to set the frontside bus frequency for the installed processor (Min 200 MHz,
Max 232 MHz).
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-20
Chapter 3
3-8. Load Fail-Safe Defaults
This option loads the BIOS default values for the most stable, minimal-performance system operations.
3-9. Load Optimized Defaults
This option loads the BIOS default values that are factory settings for optimal-performance system
operations.
3-10. Set User Password
This option protects the BIOS configuration or restricts access to the computer itself.
3-11. Save & Exit Setup
This option saves your selections and exits the BIOS setup menu.
3-12. Exit Without Saving
This option exits the BIOS setup menu without saving any change.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver Installation
4-1
Chapter 4. Driver Installation
All the necessary drivers are included within the Drivers & Utilities CD that came packed with the
motherboard. The display shown in the following figure should appear after inserting the Drivers &
Utilities CD into your CD-ROM drive, if not, enter $[My Computer] $[CD-ROM] Drive $double
click [autorun.exe]. Please follow the on-screen instruction.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2
Chapter 4
4-1. Setup Items
Drivers:
•
•
•
•
•
VIA 4in1 Driver
Install the VIA 4-in-1 driver for Windows Operating System.
VIA VGA Driver
Install the VIA VGA graphic driver for Windows Operating System.
Audio Driver
Install the audio driver for Windows Operating System.
LAN Driver
Install the LAN driver for Windows Operating System.
VIA USB 2.0 Driver
(1) Install the VIA USB 2.0 driver for Windows 98/ME Operating System.
(2) The installation of USB 2.0 driver for Windows XP or Windows 2000 is currently available
by updating the latest service pack from Microsoft’s website.
•
•
VIA South Bridge SATA RAID Driver
Install the VIA Serial ATA RAID driver for Windows Operating System.
AMD Cool’n’Quiet Driver
Install the AMD Athlon 64 Processor driver for Windows Operating System.
Manual:
•
View the user’s manual in PDF file.
Utility:
•
Click to enter the sub-screen for installing software like Award Flash, Acrobat Reader, DirectX,
and LoFormat utility.
ABIT Utility:
•
This model does not support ABIT Utility.
Browse CD:
•
Browse the contents of this CD-ROM.
Close:
•
Exit the CD setup Items Menu.
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Get Technical Support
A-1
Appendix A. How to Get Technical Support
(From our website) http://www.abit.com.tw
(In North America) http://www.abit-usa.com
(In Europe) http://www.abit.nl
Thank you for choosing ABIT products. ABIT sells all our products through distributors,
resellers and system integrators; we have no direct sales to end-users. Before sending email
for tech support please check with your resellers or integrators if you need any services, they
are the ones who sold you your system and they should know best as to what can be done,
how they serve you is a good reference for future purchases.
We appreciate every customer and would like to provide the best service to you. Providing
fast service to our customers is our top priority. However we receive many phone calls and a
huge amount of email from all over the world. At the present time it is impossible for us to
respond to every single inquiry.
We have done many compatibility tests and reliability tests to make sure our products have
the best quality and compatibility. In case you need service or technical support, please
understand the constraints that we have and always check with the reseller who sold the
product to you first.
To expedite service, we recommend that you follow the procedures outlined below before
contacting us. With your help, we can meet our commitment to provide the best service to the
greatest number of ABIT customers:
1. Check the Manual. It sounds simple but we have taken a lot of care in making a
well-written and thorough manual. It is full of information that doesn't only pertain to
motherboards. The CD-ROM included with your board will have the manual as well as
drivers. If you don't have either one, go to our Program Download area of the website or
our FTP server.
2. Download latest BIOS, software or drivers. Please go to our Program Download area
on our website to check to see if you have the latest BIOS. They are developed over
periods of time to fixes bugs or incompatibilities. Also please make sure you have the
latest drivers from your peripheral card makers!
3. Check the ABIT Technical Terms Guide and FAQ on our website. We are trying to
expand and make the FAQs more helpful and information rich. Let us know if you have
any suggestions. For hot topics, check out our HOT FAQ!
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
A-2
Appendix A
4. Internet Newsgroups. These are a great source of information and many people there can
forum for the public to exchange information and discuss experiences they have had with
ABIT products. Many times you will see that your question has already been asked before.
This is a public Internet news group and it is reserved for free discussions. Here is a list of
some of the more popular ones:
5. Ask your reseller. Your ABIT authorized distributor should be able to provide the fastest
solution to your technical problem. We sell our products through distributors who sell to
resellers and stores. Your reseller should be very familiar with your system configuration
and should be able to solve your problem much more efficiently than we could. After all,
your reseller regards you as an important customer who may purchase more products and
who can urge your friends to buy from him or her as well. They integrated and sold the
system to you. They should know best what your system configuration is and your
problem. They should have reasonable return or refund policies. How they serve you is
also a good reference for your next purchase.
6. Contacting ABIT. If you feel that you need to contact ABIT directly you can send email
to the ABIT technical support department. First, please contact the support team for the
branch office closest to you. They will be more familiar with local conditions and will
have better insight as to which resellers offer what products and services. Due to the huge
number of emails coming in every day and other reasons, such as the time required for
problem reproduction, we will not be able to reply to every email. Please understand that
we are selling through distribution channels and while we don't have the resources to
serve every end-user, we will do our best to help every customer. Please also remember
that for many of our technical support team English is a second language. You will have a
better chance of getting a helpful answer if your question can be quickly understood. Be
sure to use very, simple, concise language that clearly states the problem, avoid rambling
or flowery language, and always list your system components and operating system. Here
is the contact information for our branch offices:
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Get Technical Support
A-3
North America and
South America
ABIT Computer (U.S.A.) Corporation
2901 Bayview Drive
Fremont, CA 94538, U.S.A.
Tel: 1-510-623-0500
Fax: 1-510-623-1092
Sales: [email protected]
Latin America Sales: [email protected]
Marketing: [email protected]
Web Site: http://www.abit-usa.com
RMA Center: http://rma.abit-usa.com/
UK and Ireland
ABIT Computer (U.K.) Corporation Ltd.
Unit 3, 24-26 Boulton Road, Stevenage,
Herts SG1 4QX, UK
Tel: 44-1438-228888
Fax: 44-1438-226333
E-mail: [email protected]
Germany and Benelux (Belgium,
Netherlands, Luxembourg),
France, Italy, Spain, Portugal,
Greece, Denmark, Norway,
Sweden, Finland, and
AMOR Computer B.V. (ABIT's European Office)
Jan van Riebeeckweg 15, 5928LG, Venlo,
The Netherlands
Tel: 31-77-3204428
Fax: 31-77-3204420
Switzerland
Sales: [email protected]
Web Site: http://www.abit.nl
Austria, Czech, Romania,
Bulgaria, Slovakia, Croatia,
Bosnia, Serbia, and Macedonia
Asguard Computer Ges.m.b.H
Schmalbachstrasse 5,
A-2201 Gerasdorf / Wien, Austria
Tel: 43-1-7346709
Fax: 43-1-7346713
E-mail: [email protected]
Shanghai
ABIT Computer (Shanghai) Co. Ltd.
Tel: 86-21-6235-1829
Fax: 86-21-6235-1832
Web Site: http://www.abit.com.cn
Russia and CIS
ABIT Computer (Russia) Co. Ltd.
Sales: [email protected]
Info: [email protected]
Web Site: http://www.abit.ru
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
A-4
Appendix A
Poland
ABIT Computer (Poland) Co. Ltd.
Przedstawicielstwo w Polsce ul. Wita Stwosza 28,
50-149 Wrocław
Tel: 48 71 780 78 65 / 66
Fax: 48 71 372 30 87
Japan
Web Site: http://www.abit4u.jp
Taiwan Head Office
ABIT Computer Corporation
No. 323, Yang Guang St., Neihu,
Taipei, 114, Taiwan
Tel: 886-2-8751-8888
Fax: 886-2-8751-3382
Sales: [email protected]
Marketing: [email protected]
Web Site: http://www.abit.com.tw
(Serving all other territories
not listed above.
Taiwan is 8+ GMT time,
and may have different holiday
calendar from yours.)
7. RMA Service. If your system has been working but it just stopped, but you have not
installed any new software or hardware recently, it is likely that you have a defective
component. Please contact the reseller from whom you bought the product. You should be
able to get RMA service there.
8. Reporting Compatibility Problems to ABIT. Because of tremendous number of email
messages we receive every day, we are forced to give greater weight to certain types of
messages than to others. For this reason, any compatibility problem that is reported to us,
giving detailed system configuration information and error symptoms will receive the
highest priority. For the other questions, we regret that we may not be able to reply
directly. But your questions may be posted to the Internet news group in order that a
larger number of users can have the benefit of the information. Please check the news
group from time to time.
Thank You
ABIT Computer Corporation
KV-85
Download from Www.Somanuals.com. All Manuals Search And Download.
|