3M Food Saver 800a3 User Manual
Instructions and Parts List  
Important Safety  
Information  
BEFORE INSTALLING  
OR OPERATING THIS  
EQUIPMENT  
3M-Matic™  
Read, understand, and  
follow all safety and  
operating instructions.  
800a3 Type 40800  
Adjustable  
Case Sealer  
Spare Parts  
with  
It is recommended you  
immediately order the  
spare parts listed in the  
"Spare Parts/Service  
Information" section.  
These parts are expected  
to wear through normal  
use, and should be kept  
on hand to minimize  
production delays.  
AccuGlide™ 3  
Taping Heads  
Serial No.  
For reference, record machine serial number here.  
"3M-Matic"and "AccuGlide" are Trademarks of,  
3M St. Paul, MN 55144-1000  
Printed in U.S.A.  
3M Industrial Adhesives and Tapes  
3M Center, Building 220-5E-06  
St. Paul, MN 55144-1000  
© 3M 2011 44-0009-2081-7 (D092311-NA)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts and Service Information  
To Our Customers:  
This is the 3M-Matic™/AccuGlide™/Scotch® equipment you ordered. It has been set up and tested in  
the factory with Scotch® tapes. If technical assistance or replacement parts are needed, call or fax the  
appropriate number listed below.  
Included with each machine is an Instructions and Parts List manual.  
Technical Assistance / Replacement Parts and Additional Manuals:  
Contact your local service provider. Provide the customer support coordinator with the model/machine  
name, machine type, and serial number that are located on the identification plate (For example: Model  
800a3 - Type 40800 - Serial Number 13282).  
Identification Plate  
Minimum billing on parts orders will be $25.00. Replacement part prices available on request.  
$10.00 restocking charge per invoice on returned parts  
3M-Matic™, AccuGlide™ and Scotch™  
are Trademarks of  
3M Industrial Adhesives and Tapes  
3M Center, Building 220-5E-06  
3M St. Paul, MN 55144-1000  
St. Paul, MN 55144-1000  
Printed in U.S.A.  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts And Service Information  
To Our Customers:  
This is the 3M-Matic™/AccuGlide™/Scotch® equipment you ordered. It has been set up  
and tested in the factory with Scotch® tapes. If any problems occur when operating this equipment and  
you desire a service call or phone consultation, call, write, or fax the appropriate number listed below.  
Included with each machine is an Instructions and Parts List manual.  
SERVICE, REPLACEMENT PARTS, AND ADDITIONAL MANUALS  
AVAILABLE DIRECT FROM:  
Order parts by part number, part description, and quantity required. Also, when ordering parts  
or additional manuals, include model/machine name, machine type, and serial number that are  
located on the identification plate.  
3M-Matic™, AccuGlide™ and Scotch™  
are Trademarks of  
3M, St. Paul, MN 55144-1000  
Printed in U.S.A.  
3M Industrial Adhesives and Tapes  
3M Center, Building 220-5E-06  
St. Paul, MN 55144-1000  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS - MANUAL 1: 800a3 Adjustable Case Sealer  
(For Taping Head Information - See MANUAL 2: AccuGlide™ 3 Taping Heads - 3 inch)  
800a3 Adjustable Case Sealer  
Page  
Cover Page  
Replacement Parts and Service Information ........................................................................i - ii  
Table of Contents ................................................................................................................. iii - v  
Acronyms and Abbreviations ................................................................................................vi  
1. Introduction  
1.1 Manufacturing Specifications / Description / Intended Use ......................................... 1 - 2  
1.2 How to Read and Use the Manual ............................................................................... 2  
1.2.1 Importance of the Manual .................................................................................. 2  
1.2.2 Manual Maintenance ......................................................................................... 2  
1.2.3 Consulting the Manual ........................................................................................ 2  
1.2.4 How to Update the Manual in Case of Modifications ...........................................2  
2. General Information  
2.1 Identification Data .........................................................................................................3  
2.2 After-Sale Service .........................................................................................................3  
2.3 Warranty / Contents ......................................................................................................4  
3. Safety  
3.1 General Safety Information ...........................................................................................5  
3.2 Signal Words Explanation ............................................................................................. 5  
3.3 Table of Warnings ..........................................................................................................6 - 7  
3.4 Operator’s Qualifications Definition .............................................................................. 8  
3.5 Number of Operators ....................................................................................................8  
3.6 Safe Use of the Machine Instructions ...........................................................................8  
3.7 Residual Hazards .......................................................................................................... 8  
3.8 Prevent Other Hazards - Recommendations and Measures ........................................8  
3.9 Personal Safety Measures ........................................................................................... 8  
3.10 Incorrect / Predictable Actions Not Allowed ..................................................................8  
3.11 Operator's Required Skill Levels .................................................................................. 9  
3.12 Component Locations .................................................................................................. 10  
3.13 Table of Warnings and Replacement Labels ................................................................11  
4. Technical Specifications  
4.1 Power Requirements ....................................................................................................12  
4.2 Operating Rate  
............................................................................................................. 12  
4.3 Operating Conditions ....................................................................................................12  
4.4 Tape ..............................................................................................................................12  
4.5 Tape Width ....................................................................................................................12  
4.6 Tape Roll Diameter .......................................................................................................13  
4.7 Tape Application Leg Length - Standard .......................................................................13  
Tape Application Leg Length - Optional  
4.8 Box Board .....................................................................................................................13  
4.9 Box Weight and Size Capacities ................................................................................... 13  
4.10 Machine Noise Levels ................................................................................................... 14  
4.11 Machine Dimensions ..................................................................................................... 14  
4.12 Set-Up Recommendations ............................................................................................ 14  
2011 September  
800a3-NA  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS (continued)  
5. Shipment, Handling, and Storage  
5.1 Packed Machine Shipment and Handling ...........................................................................15  
5.2 Overseas Shipment Packaging (Optional) ..........................................................................15  
5.3 Handling and Transportation of Uncrated Machine .............................................................15  
5.4 Machine Storage .................................................................................................................15  
6. Unpacking  
6.1 Uncrating .............................................................................................................................16  
6.2 Packaging Materials Disposal .............................................................................................16  
7. Installation  
7.1 Operating Conditions .......................................................................................................... 17  
7.2 Space Requirements for Machine Operation and Maintenance ......................................... 17  
7.3 Tool Kit Supplied with the Machine ..................................................................................... 17  
7.4 Machine Positioning / Machine Set-Up ................................................................................17  
7.5 Plastic Ties Removal ...........................................................................................................18  
7.6 Assembly Completion .......................................................................................................... 18  
7.7 Taping Heads Completion ...................................................................................................19  
7.8 Outboard Tape Roll Holder ................................................................................................. 19  
7.9 Preliminary Electric Inspection ............................................................................................19  
7.10 Main Power Machine Connection and Inspection .............................................................. 19  
7.11 Phases Inspection ............................................................................................................... 19  
8. Theory of Operation  
8.1 Working Cycle Description ..................................................................................................20  
8.2 Running Mode Definition .....................................................................................................20  
8.3.1 Normal Stop Procedure .............................................................................................20  
8.3.2 Emergency Stop ....................................................................................................... 20  
9. Controls  
9.1 Box Width Adjusting Knobs .................................................................................................21  
9.2 Box Height Adjusting Crank ................................................................................................ 21  
9.3 Start / Stop Main Switch .......................................................................................................21  
9.4 Emergency Stop Button (Latching) .....................................................................................21  
10. Safety devices  
10.1 Blade Guards ..................................................................................................................... 22  
10.2 Emergency Stop Button ..................................................................................................... 22  
10.3 Electric System / Circuit Breaker .........................................................................................22  
11. Set-Up and Adjustments  
11.1 Box Width Adjustment ........................................................................................................ 23  
11.2 Box Height Adjustment .......................................................................................................23  
11.3 Top Flap Compression Roller Adjustment .......................................................................... 23  
11.4 Changing the Tape Leg Length .......................................................................................... 23  
11.5 Run Boxes to Check Adjustment ........................................................................................23  
2011 September  
800a3-NA  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS (continued)  
12. Operation  
12.1 Operator’s Correct Working Position .............................................................................. 24  
12.2 Starting the Machine .......................................................................................................24  
12.3 Starting Production ......................................................................................................... 24  
12.4 Tape Replacement ..........................................................................................................24  
12.5 Box Size Adjustment .......................................................................................................24  
12.6 Cleaning ......................................................................................................................... 24  
12.7 Table of Adjustments ...................................................................................................... 24  
12.8 Safety Devices Inspection .............................................................................................. 24  
12.9 Trouble Shooting ............................................................................................................ 25  
13. Maintenance  
13.1 Safety Measures (see section 3) .................................................................................... 26  
13.2 Tools and Spare Parts Supplied with Machine ............................................................... 26  
13.3 Maintenance Operations - Recommended Inspections and Frequency ..........................26  
13.4 Inspections to be Performed Before and After Every Maintenance Operation ................ 26  
13.5 Safety Features (Inspection Efficiency) .......................................................................... 26  
13.6 Machine Cleaning ...........................................................................................................26  
13.7 Cutter Blade Cleaning .................................................................................................... 26  
13.8 Drive Belt Replacement ..................................................................................................27 - 28  
13.9 Drive Pulley Ring ............................................................................................................ 28  
13.10 Drive Belt Tension ...........................................................................................................29  
13.11. Special Set-Up Procedures ............................................................................................ 29 - 35  
13.11.1 Case Sealer Frame ........................................................................................... 29  
13.11.2 Taping Heads .....................................................................................................30 - 31  
13.11.3 Drive Belt Assembly Height ............................................................................... 31  
13.11.4 Box Height Range (Outer Column Repositioning) .......................................... 32 - 35  
13.12 Maintenance Work Log ...................................................................................................37  
14. Additional Instructions  
14.1 Machine Disposal Information ........................................................................................ 39  
14.2 Fire emergency ...............................................................................................................39  
15. Enclosures and Special Information  
15.1 Statement of Conformity .................................................................................................39  
15.2 Hazardous Substances Emission ...................................................................................39  
16. Technical Documentation and Information  
16.1 Electric Diagrams ........................................................................................................... 41  
16.2 Spare Parts / Ordering ....................................................................................................42 - 43  
Drawings and Parts Lists ....................................................................................................... 45 - End of Manual  
TAPING HEAD INFORMATION -  
MANUAL 2: AccuGlide™ 3 Taping Heads - 3 inch (See MANUAL 2 for Table of Contents)  
2011 September  
800a3-NA  
v
Download from Www.Somanuals.com. All Manuals Search And Download.  
ABBREVIATIONS AND ACRONYMS  
LIST OF ABBREVIATIONS, ACRONYMS  
3M-Matic - Trademark of 3M St. Paul, MN 55144- 1000  
AccuGlide - Trademark of 3M St. Paul, MN 55144-1000  
Scotch  
Drw.  
Ex.  
- Trademark of 3M St. Paul, MN 55144-1000  
- drawing  
- for example  
Fig.  
- exploded view figure no. (spare parts)  
- Illustration  
Figure  
Max.  
Min.  
Nr.  
- maximum  
- minimum  
- number  
N/A  
- not applicable  
OFF  
ON  
- machine not operating  
- machine operating  
- Programmable Logic Control  
- Polypropylene  
PLC  
PP  
PTFE  
- Polytetraflourethelene  
PU/PU Foam - Polyurethane Foam  
PVC  
W
- Poly-vinyl chloride  
- Width  
H
- Height  
L
- Length  
vi  
2011 September  
800a3-NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-INTRODUCTION  
1.1 Manufacturing Specifications / Description / Intended Use  
The 3M-MaticTM 800a3 Adjustable Case Sealer with AccuGlideTM Taping Heads is designed to apply a “C”  
clip of Scotch® pressure-sensitive film box sealing tape to the top and bottom center seam of regular slotted  
containers. The 800a3 is manually adjustable to a wide range of box sizes (see "Specifications Section – Box  
Weight and Size Capacities").  
3
3M-MaticTM 800a3 Adjustable Case Sealer, Type 40800  
Note – Shown above is the lower tape supply roll and bracket assembly in the alternate location.  
2011 September  
800a3-NA  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-INTRODUCTION (continued)  
1.1 Manufacturing Specifications / Description /  
Intended Use (continued)  
1.2.2 Manual Maintenance  
Keep the manual in a clean and dry place near the  
machine. Do not remove, tear, or rewrite parts of  
the manual for any reason. Use the manual without  
damaging it. In case the manual has been lost or  
damaged, ask your after sale service for a new copy.  
The 3M-MaticTM case sealing machines have been  
designed and manufactured in compliance with the  
legal requirements at the date of inception.  
1.2 How to Read and Use the Instruction Manual  
1.2.3 Consulting the Manual  
This instruction manual covers safety aspects,  
handling and transport, storage, unpacking, prepara-  
tion, installation, operation, set-up and adjustments,  
technical and manufacturing specifications, mainte-  
nance, troubleshooting, repair work and servicing,  
electric diagrams, warranty information, disposal  
(ELV), a definition of symbols, plus a parts list of the  
3M-MaticTM 800a3 Adjustable case sealer  
The manual is composed of:  
- Pageswhichidentifythedocumentandthemachine  
- Index of the subjects  
- Instructions and notes on the machine  
- Enclosures, drawings and diagrams  
- Spare parts (last section)  
3M Industrial Adhesives and Tapes Division 3M Cen-  
ter, Bldg. 220-5E-06 St. Paul, MN 55144-1000 (USA)  
Edition September 2011 Copyright 3M 2011 All rights  
reserved. The manufacturer reserves the right to  
change the product at any time without notice Publi-  
cation © 3M 2011 44-0009-2081-7.  
All pages and diagrams are numbered. The spare  
parts lists are identified by the figure identification  
number. All the notes on safety measures or  
possible dangers are identified by the symbol:  
1.2.1 Importance of the Manual  
1.2.4 How to Update the Manual in Case of  
Modifications to the Machine  
The manual is an important part of the machine; all  
information contained herein is intended to enable  
the equipment to be maintained in perfect condition  
and operated safely. Ensure that the manual is avail-  
able to all operators of this equipment and is kept  
up to date with all subsequent amendments. Should  
the equipment be sold or disposed of, please ensure  
that the manual is passed on. Electrical and pneu-  
matic diagrams are included in the manual. Equip-  
ment using PLC controls and/or electronic compo-  
nents will include relevant schematics or programs in  
the enclosure and in addition, the relevant documen-  
tation will be delivered separately.  
Modifications to the machine are subject to manu-  
facturer’s internal procedures. The user receives a  
complete and up-to-date copy of the manual to-  
gether with the machine. Afterwards the user may  
receive pages or parts of the manual which contain  
amendments or improvements made after its first  
publication. The user must use them to update this  
manual.  
2
2011 September  
800a3-NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-GENERAL INFORMATION  
2.1 Data Identifying Manufacturer and Machine  
2.2 Data for Technical Assistance and Service  
2011 September  
800a3-NA  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-GENERAL INFORMATION (continued)  
2.3 Warranty  
Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTY OF MERCHANTABILITY, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR  
PURPOSE AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, A CUSTOM OR  
USAGE OF TRADE:  
3M sells its 3M-Matic™ 800a3 Adjustable Case Sealer, Type 40800 with the following warranties:  
1. The drive belts and the taping head knives, springs and rollers will be free from all defects for ninety (90  
days after delivery.  
2. All other taping head parts will be free from all defects for three (3) years after delivery.  
3. All other parts will be free from all defects for two (2) years after delivery.  
If any part is proved to be defective within its warranty period, then the exclusive remedy and 3M’s and seller’s  
sole obligation shall be, at 3M’s option, to repair or replace the part, provided the defective part is returned  
immediately to 3M’s factory or an authorized service station designated by 3M. A part will be presumed to have  
become defective after its warranty period unless the part is received or 3M is notified of the problem no later than  
five (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable  
time, then 3M at its option, will replace the equipment or refund the purchase price. 3M shall have no obligation  
to provide or pay for the labor required to install the repaired or replacement part. 3M shall have no obligation  
to repair or replace (1) those parts failing due to operator misuse, carelessness, or due to any accidental cause  
other than equipment failure, or (2) parts failing due to non-lubrication, inadequate cleaning, improper operating  
environment, improper utilities or operator error.  
Limitation of Liability: 3M and seller shall not be liable for direct, indirect, special, incidental or consequential  
damages based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory.  
The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability may be changed only by a  
written agreement signed by authorized officers of 3M and seller.  
Contents—800a3 Adjustable Case Sealer  
(1)  
(1)  
(1)  
800a3 Adjustable Case Sealer, Type 40800  
Tool and Spare Parts Kit  
Instruction and Parts Manual  
2011 September  
800a3-NA  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-SAFETY  
3.1 General Safety Information  
3.2 Explanation of Signal Word and  
Possible Consequences  
Read all the instructions carefully before starting  
work with the machine; please pay particular atten-  
tion to sections marked by the symbol:  
This safety alert symbol identifies  
important messages in this manual.  
READ AND UNDERSTAND THEM  
BEFORE INSTALLING OR  
Figure 3-1  
OPERATING THIS EQUIPMENT.  
E-Stop  
Switch  
CAUTION: Indicates a potentially hazardous  
situation, which, if not avoided,  
may result in minor or moderate  
injury and/or property damage.  
WARNING: Indicates a potentially hazardous  
situation, which, if not avoided,  
could result in death or serious  
injury and/or property damage.  
The machine is provided with a LATCHING EMER-  
GENCY STOP BUTTON (Figure 3-1); when this  
button is pressed, it stops the machine at any point  
in the working cycle. Maintain clear access to power  
cord while machine is operating. Disconnect plug  
from power source before machine maintenance  
(Figure 3-1). Also disconnect air if the machine has  
a pneumatic system. Keep this manual in a handy  
place near the machine. This manual contains infor-  
mation that will help you to maintain the machine in  
a good and safe working condition.  
2011 September  
800a3-NA  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-SAFETY (continued)  
3.3 Table of Warnings  
WARNING  
• To reduce the risk associated with  
mechanical and electrical hazards:  
− Read, understand, and follow all safety and  
operating instructions before operating or  
servicing the case sealer.  
− Allow only properly trained and qualified  
personnel to operate and service this  
equipment.  
Figure 3-2  
WARNING  
• To reduce the risk associated with  
hazardous voltage:  
− Position electrical cord away from foot and  
vehicle traffic.  
WARNING  
Figure 3-3  
• To reduce the risk associated with  
pinches, entanglement and hazardous  
voltage:  
− Turn electrical supply off and disconnect  
before performing any adjustments,  
maintenance or servicing the machine or  
taping heads.  
WARNING  
• To reduce the risk associated with  
pinches and entanglement hazards:  
− Do not leave the machine running while  
Figure 3-4  
unattended.  
− Push the machine off when not in use.  
− Never attempt to work on any part of the  
machine, load tape, or remove jammed  
boxes from the machine while the machine  
is running.  
Important! Cavity in the conveyor bed. Never put  
your hands inside any part of the machine while it is  
working. Serious injury may occur (Figure 3-4).  
2011 September  
800a3-NA  
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-SAFETY (continued)  
WARNING  
•
To reduce the risk associated with  
sharp blade hazards:  
− Keep hands and fingers away from  
tape cutoff blades under orange blade  
guards. The blades are extremely sharp.  
WARNING  
Sharp Blade  
Important! Tape cutting blade. Never remove the  
safety device which covers the blade on the top and  
bottom taping units. Blades are extremely sharp. Any  
error may cause serious injuries (Figure 3-5).  
Figure 3-5  
WARNING  
•
To reduce the risk associated with  
fire and explosion hazards:  
− Do not operate this equipment  
in potentially flammable/explosive  
environments.  
WARNING  
•
To reduce the risk associated with  
muscle strain:  
− Use the appropriate rigging and  
material handling equipment when  
lifting or repositioning this equipment.  
− Use proper body mechanics when  
removing or installing taping heads  
that are moderately heavy or may be  
considered awkward to lift.  
Figure 3-6  
CAUTION  
• To reduce the risk associated with  
pinch hazards:  
− Keep hands clear of the upper head  
support assembly as boxes are  
transported through the machine.  
− Keep hands, hair, loose clothing, and  
jewelry away from box compression rollers.  
− Always feed boxes into the machine by  
pushing only from the end of the box.  
− Keep hands, hair, loose clothing, jewelry  
away from moving belts and taping heads.  
Figure 3-7  
2011 September  
800a3-NA  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-SAFETY (continued)  
3.4 Operator's Qualifications  
WARNING  
- Machine Operator  
• To reduce the risk associated with  
- Mechanical Maintenance Technician  
- Electrical Maintenance Technician  
- Manufacturer’s Technician/Specialist  
(See Section 3)  
mechanical and electrical hazards:  
− Read, understand, and follow all safety and  
operating instructions before operating or  
servicing the case sealer.  
− Allow only properly trained and qualified  
personnel to operate and service this  
equipment.  
3.5 Number of Operators  
The operations described below have been analyzed  
by the manufacturer; the recommended number of  
operators for each operation provides the best and  
safest work performance.  
3.9 Personal Safety Measures  
Safety glasses, safety gloves, safety helmet, safety  
shoes, air filters, ear muffs - None is required except  
when recommended by the user.  
Note: A smaller or greater number of operators  
could be unsafe.  
3.10 Predictable Actions which are Incorrect and  
Not Allowed  
3.6 Instructions for a Safe Use of the Machine /  
Definition of Operator's Qualif cations  
- Never try to stop/hold the box while being driven  
by the belts.  
Only persons who have the skills described in the  
skill levels section should be allowed to work on the  
machine. It is the responsibility of the user to appoint  
the operators having the appropriate skill level and  
the appropriate training for each category of job.  
- Never remove or disable the safety devices.  
- Only authorized personnel should be allowed  
to carry out the adjustments, repairs or main-  
tenance which require operation with reduced  
safety protections. During such operations,  
access to the machine must be restricted.  
When the work is finished, the safety protec-  
tions must immediately be reactivated.  
3.7 Residual Hazards  
The case sealer 800a3 incorporates various safety  
protections which should never be removed or  
disabled. It is essential that the operator and service  
personnel be warned that hazards exist which can-  
not be eliminated.  
- The cleaning and maintenance operations must be  
performed after disconnecting the electric power.  
- Do not modify the machine or any part of it.  
- Clean the machine using only dry cloths or  
light detergents. Do not use solvents, petrols, etc.  
3.8 Recommendations and Measures to Prevent  
Other Hazards which Cannot be Eliminated  
- Install the machine following the suggested layouts  
and drawings.  
- The operator must stay on the working position  
shown in the Operation Section. He must never  
touch the running driving belts or put his hands  
inside any cavity.  
- The operator must pay attention to the blades  
during the tape replacement.  
2011 September  
800a3-NA  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-SAFETY (continued)  
Skill 2a: Electrical Maintenance Technician  
This operator is trained to use the machine as the  
MACHINE OPERATOR and in addition is able to:  
• Work with the safety protection disconnected  
• Check and adjust mechanical parts  
• Carry out machine maintenance operations / re-  
pairs / adjustments / repair electrical components  
He is allowed to work on live electrical panels,  
connector blocks, control equipment, etc.  
3.11 Operator's Skill Levels Required to Perform  
the Main Operations on the Machine  
The Table shows the minimum operator's skill for  
each machine operation.  
Important: The factory manager must ensure that  
the operator has been properly trained on all the  
machine functions before starting work.  
Skill 1: Machine Operator  
Skill 3: Specialist from the Manufacturer  
Skilled operator sent by the manufacturer or its  
agent to perform complex repairs or modifications  
(on agreement with the customer).  
This operator is trained to use the machine with the  
machine controls, to feed cases into the machine,  
make adjustments for different case sizes, to change  
the tape and to start, stop and restart production.  
Skill 2: Mechanical Maintenance Technician  
This operator is trained to use the machine as the  
MACHINE OPERATOR and in addition is able to:  
• Work with the safety protection disconnected  
• Check and adjust mechanical parts  
WARNING  
• To reduce the risk associated with  
mechanical and electrical hazards:  
− Allow only properly trained and qualified  
• Carry out machine maintenance operations/repairs  
He is not allowed to work on live electrical components  
personnel to operate and service this machine  
Operator's Skill Levels Required to Perform the Main Operations on Machine  
Required  
Operator  
Skill  
Number of  
Operators  
Operation  
Machine Status  
Machine installation and setup  
Adjusting box size  
Running with safety  
protections disabled  
2 and 2a  
1
2
1
Stopped by pressing the  
EMERGENCY STOP  
button  
Stopped by pressing the  
EMERGENCY STOP  
button  
Tape replacement  
1
1
Blade replacement  
Electric power  
disconnected  
2
2
1
1
1
1
Drive belt replacement  
Ordinary maintenance  
Electric power  
disconnected  
Electric power  
disconnected  
2
Extraordinary mechanical  
maintenance  
Running with safety  
protections disabled  
3
Extraordinary electrical  
maintenance  
Running with safety  
protections disabled  
2a  
1
2011 September  
800a3-NA  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-SAFETY (continued)  
3.12 Component Locations  
Refer to Figure 3-8 below to acquaint yourself with the various components and controls of the case sealer.  
Also refer to Manual 2 for taping head components.  
Height  
Adjustment  
Handle  
Top Flap  
Compression  
Rollers  
Emergency  
Stop Button  
Upper Taping Head  
Lower Taping Head  
Adjustable  
Side Drives  
Electrical  
Control Box  
Width  
Adjustment  
Crank  
Machine Bed  
(Alternate)  
Lower Tape  
Roll Mount  
Electrical  
On/Off  
Switch  
Figure 3-8—800a3 Case Sealer Components (Left Front View)  
2011 September  
800a3-NA  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-SAFETY (continued)  
3.13 Table of Warnings and Replacements Labels (continued)  
78-8113-6912-9 (2)  
UP  
DOWN  
78-8095-1141-9  
STOP  
78-8095-1628-8  
78-8070-1366-5  
78-8070-1336-8  
78-8070-1629-6  
78-8062-4266-1  
78-8137-0886-0  
78-8060-8481-6  
Leg Height Adjustment Label  
(not shown)  
78-8070-1339-2  
3M Logo  
78-8113-6717-2  
78-8070-1329-3  
(not shown)  
Figure 3-9 - Replacement Labels / 3M Part Numbers  
2011 September  
800a3-NA  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-SPECIFICATIONS  
1. Power Requirements  
Electrical: 115 Volt, 60Hz, 3.8 A (220 watts)  
The machine is equipped with a 2.4m [8 foot] standard neoprene covered power cord and a grounded plug.  
Contact your 3M Representative for power requirements not listed above.  
2. Operating Rate  
Belt speed is 0.5m/s [100 ft/min].  
Actual production rate is dependent on operator's dexterity.  
Boxes must be 18 inches (455mm) apart minimum.  
3. Operating Conditions  
IMPORTANT SAFEGUARD  
Use in dry, relatively clean environments at 5o C to 50o C [40o F to 120o F] with clean, dry boxes.  
Note: Machine should not be washed or subjected to conditions causing moisture condensation on  
components.  
WARNING  
• To reduce the risk associated with fire  
and explosion hazards:  
− Do not operate this equipment in poten-  
tially flammable or explosive environments.  
4. Tape  
Scotch® pressure-sensitive film box sealing tapes.  
5. Tape Width  
50mm [2 inch] minimum to 75mm [3 inch] maximum  
2011 September  
800a3-NA  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-SPECIFICATIONS (continued)  
Specifications  
6. Tape Roll Diameter  
Up to 405mm [16 inch] maximum on a 76.2mm [3 inch] diameter core.  
(Accommodates all system roll lengths of Scotch® film tapes.)  
7. Tape Application Leg Length – Standard  
70 mm ± 6mm [2.75 inch ±. 25 inch ]  
Tape Application Leg Length – Optional  
50 mm ± 6mm [2 inch ±. 25 inch]  
(See "Removing Taping Heads Procedure – Changing the Tape Leg Length")  
8. Box Board  
Style – regular slotted containers – RSC  
125 to 275 P.S.I. bursting test, single wall or double wall B or C flute.  
23-44 lbs. per inch of width Edge Crush Test (ECT)  
9. Box Weight and Size Capacities  
A. Box Weight, filled: 5 lbs.–85 lbs. [2.3 kg–38.6 kg]. Contents must support flaps.  
B. Box Size:  
Length –  
Minimum  
Maximum  
150mm [6.0 inch]  
Unlimited  
Width  
Height –  
–
140mm [5.5 inch]*  
120mm [4.75 inch]** ***  
545mm [21.5 inch]  
620mm [24.5 inch] ***  
*
Minimum box height can be reduced to 110mm [4-1/4 inches] by removing machine compression rollers OR  
Minimum box height can be reduced to 90mm [3 1/2 inches] by removing machine compression rollers and  
also adjusting taping heads to apply 48mm [2 inch] tape legs (See "Special Set-Up Procedure".)  
** Maximum box height can be increased to7 25mm [28-1/2 inches] by relocating machine outer columns to  
upper position. (See "Special Set-Up Procedure".)  
Note: Raising columns to upper position also increases minimum  
box height to 210mm [8-1/4 inches].  
Note: The case sealer can accommodate most boxes within the size range listed above. However, if the box  
length (in direction of seal) to box height ratio is 0.6 or less, test run several boxes to ensure proper  
machine performance.  
DETERMINE THE BOX LIMITATIONS BY COMPLETING THIS FORMULA:  
BOX LENGTH IN DIRECTION OF SEAL  
BOX HEIGHT  
=
SHOULD BE GREATER THAN 0.6  
Any box ratio approaching this limitation should be test run to ensure performance.  
2011 September  
800a3-NA  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-SPECIFICATIONS (continued)  
L
F
F
F
W
Optional  
Infeed/Exit  
Conveyor  
Optional  
Infeed/Exit  
Conveyor  
Control  
Side  
Box Travel  
H
A
A
B
Optional Casters  
C
10. Machine Dimensions  
W
L
H
A*  
B
C
F
Minimum  
mm  
[Inches]  
980  
[38-1/2]  
920  
[36-1/4]  
1395  
[55]  
460  
[18]  
610  
[24]*  
105  
[4-3/16]  
620  
[24.5]  
Maximum  
mm  
[Inches]  
2185  
[86]*  
890  
[35]*  
- -  
- -  
- -  
- -  
- -  
* With outer columns relocated to upper position, "H" maximum dimension increases 100 mm [4 inches] and  
"B" minimum dimension decreases by 90 mm [3-1/2 inches]. (See "Special Set-Up Procedure".)  
Weight – approximate 176.9 kg [390 pounds] crated  
approximate 158.8 kg [350 pounds] uncrated  
11. Machine Noise Level: Acoustic pressure measured at a distance of 1m. from machine with  
Scotch PVC adhesive tape in operation; 78dB Acoustic radiation pressure at 1.6m. height with  
Scotch PVC adhesive tape in operation; 73dB Measurement taken with appropriate instrument:  
(Type SPYRI-MICROPHON 11).  
12. Set-Up Recommendations:  
• Machine must be level.  
• Customer supplied infeed and exit conveyors (if used) should provide straight and level box entry and exit.  
• Exit conveyors (powered or gravity) must convey sealed boxes away from machine.  
2011 September  
800a3-NA  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5-SHIPMENT-HANDLING-STORAGE, TRANSPORT  
5.1 Shipment and Handling of Packed Machine  
W
L
- The machine is fixed on the pallet with four (4) bolts  
and can be lifted by using a fork truck.  
- The package is suitable to travel by land and by air.  
- Optional sea freight package is available.  
H
Packaging Overall Dimensions  
(Figure 5-1)  
Figure 5-1  
See Specifications.  
During the shipment it is possible to stack a  
maximum of 2 machines (Figure 5-2).  
5.2 Packaging for Overseas Shipment  
(Optional - Figure 5-3)  
The machines shipped by sea freight are covered by  
an aluminum/polyester/polythene bag which  
contains dehydrating salts.  
Figure 5-2  
5.3 Handling and Transportation of Uncrated  
Machine  
The uncrated machine should not be moved except for  
short distances and indoors ONLY. Without the sup-  
porting pallet, the machine is exposed to damage and  
may cause injuries. To move the machine use belts or  
ropes, paying attention to place them in the points in-  
dicated using care to not interfere with the lower taping  
head (Figure 5-4).  
Figure 5-3  
Figure 5-4  
5.4 Storage of the Packed or Unpacked Machine  
If the machine is not used for a long period,  
please take the following precautions:  
-
-
Store the machine in a dry and clean place.  
If the machine is unpacked it is necessary to  
protect it from dust.  
-
-
Do not stack anything over the machine.  
It is possible to stack a maximum of 2 machines  
(if they are in their original packing).  
2011 September  
800a3-NA  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6-UNPACKING  
6.1 Uncrating  
Removal of Pallet  
The envelope attached to the shipping box contains  
Loosen and remove nuts and brackets using the  
the uncrating instructions of the machine (Figure 6-1).  
openendspannersuppliedinthetoolbox(Figure6-4).  
Figure 6-1  
Figure 6-4  
Cut straps. Cut out staple positions along the bottom  
of the shipping box (or remove staples with an  
appropriate tool - Figure 6-2).  
A cardboard box is located under the machine body.  
Retrieve the instruction manual for additional proce-  
dures of the set up. The box also contains parts re-  
movedforshipping, sparepartsandtools(Figure6-5).  
Figure 6-2  
After cutting out or removing the staples, lift the  
shipping box in order to clear the machine  
(two persons required).  
Figure 6-5  
6.2 Disposal of Packaging Materials  
The 800a3 package is composed of:  
- Wooden pallet  
- Cardboard shipping box  
- Wooden supports  
- Metal fixing brackets  
- PU foam protection  
- PP plastic straps  
- Dehydrating salts in bag  
- Special bag of laminated polyester/aluminium/  
Polyethylene (sea freight package only)  
- Polyethylene protective material  
Figure 6-3  
Transport the machine with a fork-lift truck to the  
operating position. Lift the pallet at the point indicat-  
ed in Figure 6-3 (weight of machine + pallet = See  
Specifications).  
For the disposal of the above materials, please follow  
the environmental directives or the law in your country.  
16  
2011 September  
800a3-NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-INSTALLATION  
7.1 Operating Conditions  
WARNING  
The machine should operate in a dry and relatively  
clean environment (See Specifications).  
• To reduce the risk associated with  
mechanical and electrical hazards:  
7.2 Space Requirements for Machine Operation  
and Maintenance Work  
− Allow only properly trained and  
qualified personnel to operate and service  
this equipment.  
Minimum distance from wall (Figure 7-1):  
A = 1000mm.  
B = 700mm.  
Minimum height = 2700mm.  
WARNING  
• To reduce the risk associated with  
muscle strain:  
− Use the appropriate rigging and  
material handling equipment when  
lifting or repositioning this equipment.  
− Use proper body mechanics when  
removing or installing taping heads  
that are moderately heavy or may be  
considered awkward to lift.  
7.4 Machine Set-Up / Bed Height  
Adjust machine bed height. The case sealer is  
equipped with four (4) adjustable legs that are  
located at the corners of the machine frame. The  
legs can be adjusted to obtain different machine bed  
heights from 610mm [24 inches] minimum to 890  
mm [35 inches] maximum - See Specifications.  
Figure 7-1  
7.3 Tool Kit Supplied with the Machine  
A tool kit containing some tools are supplied  
with the machine. These tools should be  
adequate to set-up the machine, however,  
other tools supplied by the customer will be  
required for machine maintenance.  
Refer to Figure 7-3 and set the machine bed height  
as follows:  
1. Raise and block up the machine frame to allow  
adequate leg adjustment.  
2. Loosen, but do not remove, two (2) M8 x 16mm  
socket head screws in one leg (use M6 hex  
wrench). Adjust the leg length for the desired  
machine bed height. Retighten the two screws  
to secure the leg. Adjust all four (4) legs equally.  
Figure 7-2  
M8 x 16mm  
Socket Head  
Screws  
Adjustable  
Leg  
Figure 7-3  
2011 September  
800a3-NA  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-INSTALLATION (continued)  
7.5 Removal of Plastic Ties  
Cut the plastic which attaches the top head to the  
Cut the plastic ties holding the lower taping head in  
frameandremovethepolystyreneblocks(Figure7-4).  
position (Figure 7-6).  
Figure 7-4  
Figure 7-6  
Cut the plastic strap which attaches the strip and the  
EMERGENCY STOP cable to the frame (Figure 7-5).  
7.6 Assembly Completion  
1 Crank - Install the crank handle on the top of  
the left column as shown (Figure 7-7A).  
2 Tape Drum Bracket - Install the upper tape  
drum bracket on the top cross bar as shown  
(Figure 7-7B).  
3 Stop Bracket - Raise upper head assembly  
(turn crank handle counterclockwise) and install  
the two stop brackets (provided in the parts  
bag). Use lower set of holes as shown in  
Figure 7-7D. The upper set of holes should only  
beused when both taping heads are adjusted to  
apply 50mm tape legs.  
Figure 7-5  
B
A
C
D
Figure 7-7  
2011 September  
800a3-NA  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-INSTALLATION (continued)  
7.7 Completion of Taping Heads  
One Way  
Tension  
Roller  
See Manual 2 for Complete Instructions:  
1. Place the Upper Taping Head in a convenient  
working position  
.2. Use Figure 7-8 and tape threading label.  
Position the tape supply roll so the adhesive  
side of tape is facing the front of the taping head  
as it is pulled from the supply roll.  
3. Attach the threading needle to the end of the  
roll. Guide the threading needle around the wrap  
roller (Position 1) then back around the one-  
way tension roller (Position 2).  
4. Continue pulling the threading needle down and  
guide it between the two (2) rollers on the apply  
arm (Position 3).  
#2  
Tension  
Wrap  
Roller  
#1  
Knurled  
Roller  
Wrap  
Roller  
#3  
Applying  
Roller  
5. Pull the threading needle down until the tape  
travels between the apply plate and the ears of  
the apply arm (Position 4) until it extends past  
the applying roller. When properly threaded the  
adhesive side of the tape should be facing the  
knurled rollers at position 2 and also position 3.  
6. Cut away any excess tape and repeat steps for  
Lower Taping Head.  
Threading  
Needle  
#4  
Figure 7-8  
Important – Do not cut against the apply roller -  
roller damage could occur.  
7.8 Outboard Tape Roll Holder  
Figure 7-9  
If you intend to use the outboard tape roll holder,  
proceed as follows:  
7.10 Machine Connection to the Mains  
1 - Remove the lower taping head from the machine.  
2 - Remove the tape drum bracket assembly, stud  
spacer, and fasteners from the lower taping head.  
3 - Install alternative wrap roller and bracket on the  
head in place of tape bracket. Replace lower  
head into machine.  
4 - Install and secure tape drum bracket assembly  
on the entry end of the lower frame (as shown in  
Figure 7-9).  
For technical specifications: See Section 4 -  
Specif cations  
- Push the LATCHING EMERGENCY STOP  
BUTTON.  
- The main switch is normally OFF.  
Connect the power cord supplied with the machine  
to a wall socket using a plug which complies with the  
safety regulations of your country.  
7.9 Preliminary Electric Inspection  
Before connecting the machine to the mains please  
carry out the following operations:  
7.11 Inspection of Phases  
7.9.1 Make sure that the socket is provided with an  
earth protection circuit and that both the mains  
voltage and the frequency match the specifi-  
cations on the name plate.  
7.9.2 Check that the connection of the machine  
to the mains meets the safety regulations in  
your country.  
(For Three-Main Phases Only)  
N/A  
.
7.9.3 The machine is fitted with a main switch  
and a circuit breaker. The user should check  
that the electrical settings of the machine are  
compatible with all the components of the  
mains system.  
2011 September  
800a3-NA  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8-THEORY OF OPERATION  
8.1 Description of the Working Cycle  
After having closed the top flaps of the carton, the  
operator pushes it under the top infeed end in order  
to avoid the opening of the top flaps. Further push-  
ing causes the two bottom side belts to drive the  
box through the taping heads which automatically  
seal the top and bottom seams. The carton is then  
expelled on the exit conveyor.  
Figure 8-1  
8.2 Definition of Running Mode  
The case sealer 800a3 has only one (automatic)  
operating mode with:  
- The EMERGENCY STOP BUTTON unlocked  
(Figure 8-1)  
- The main switch start switch “ON” (I)  
(Figure 8-2)  
Figure 8-2  
8.3.1 Normal Stop Procedure  
When the main switch is OFF (O), the machine  
stops immediately at any point of the working cycle.  
The same thing happens in case of electrical fail-  
ure or when the machine is disconnected from the  
mains.  
E-Stop Location  
Belt  
Direction  
8.3.2 Emergency Stop  
The LATCHING EMERGENCY STOP BUTTON is  
located on the top center of the machine  
(Figure 8-1).  
Figure 8-3  
2011 September  
800a3-NA  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9-CONTROLS  
9.1 Box Width Adjusting Knobs  
Figure 9-1  
9.2 Box Height Adjusting Crank  
Figure 9-2  
9.3 Start/Stop Button  
Figure 9-3  
E-Stop  
Switch  
9.4 Latching Emergency Stop Button  
Figure 9-4  
800a3-NA  
2011 September  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10-SAFETY DEVICES OF THE MACHINE  
10.1 Blade Guards  
10.3 Electric System / Circuit Breaker  
The electric system is protected by a ground wire  
whose continuity has been tested during the final  
inspection. The system is also subject to insulation  
and dielectric strength tests.  
Both the top and bottom taping units have a blade  
guard. (See Manual 2: AccuGlide™ 3 Taping  
Heads - 3 inch).  
Circuit Breaker  
WARNING  
The case sealer is equipped with a circuit breaker  
which trips if the motors are overloaded. Located  
inside the electrical enclosure on the side of the  
machine frame just below the machine bed, the  
circuit breaker has been pre-set and requires no  
further maintenance.  
•
To reduce the risk associated with  
sharp blade hazards:  
− Keep hands and fingers away from  
tape cutoff blades under orange blade  
guards. The blades are extremely sharp.  
10.2 Emergency Stop Button  
WARNING  
The box drive belts are turned on and off with the  
electrical switch on the side of the machine frame.  
• To reduce the risk associated with  
mechanical and electrical hazards:  
− Allow only properly trained and  
qualified personnel to operate and service  
this equipment.  
The machine electrical supply can be turned off  
by pressing the latching emergency stop switch.  
To restart machine, rotate the emergency stop  
switch clockwise to release the switch latch.  
Restart machine by Pushing the On/Off switch to  
the Off (O) position and then to the On (I) position  
(Figure 10-1)  
.
Note: The case sealer has a circuit breaker  
located in the electrical enclosure on the machine  
frame. If circuit becomes overloaded and circuit  
breaker trips, unplug the machine electrical  
cord and determine cause of overload. After two  
minutes plug machine electrical cord into outlet  
and reset the circuit breaker by turning the  
On/Off switch to the Off (O) position and then to  
the On (I) position.  
WARNING  
•
To reduce the risk associated with  
hazardous voltage:  
− Position electrical cord away from foot  
and vehicle traffic.  
Important: The use of an extension cord is not  
recommended. However, if one is needed for  
temporary use, it must:  
•
•
•
Have a wire size of 1.5mm diameter [AWG 16]  
Have a maximum length of 30.5m [100 ft]  
Be properly grounded.  
E-Stop  
Switch  
Figure 10-1  
800a3-NA  
2011 September  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11 - SET UP AND ADJUSTMENTS  
11.1 Box Width Adjustment  
Place a product filled box on infeed end of machine  
bed with top flaps folded as shown and manually  
move box forward to contact lower taping head  
applying roller.  
Turn drive belt adjustment crank to position both side  
drive belts against sides of box (Figure 11-1).  
11.2 Box Height Adjustment  
Turn height adjustment crank to position upper  
taping head onto box. Turn clockwise to lower head,  
counterclockwise to raise head. Upper taping head  
must contact and hold top box flaps closed  
(Figure 11-2).  
Figure 11-1  
11.3 Adjustment of Top Flap Compression Rollers  
The top flap compression rollers have an adjustable  
slide mounting to provide side compression through  
the full range of box widths.  
Manually move box forward so front of box is aligned  
with top flap compression rollers.  
11.4 Changing the Tape Leg Length  
Taping heads are preset to apply 70mm [2.75 inches]  
long tape legs. To change tape leg length to 50mm  
[2.0 inches], refer to Instructions below and also to  
Manual 2, "Removing Taping Heads Procedure -  
Changing the Tape Leg Length".  
11.5 Run Boxes to Check Adjustment  
Push electrical switch "On" (I) to start drive belts.  
Move box forward under upper taping head until it  
is taken away by drive belts. If box is hard to move  
under head or is crushed, raise head slightly.  
Figure 11-2  
If the box movement is jerky or stops under the upper  
head, move the side drive belts in slightly to add more  
pressure between the box and drive belts.  
Important –  
If drive belts are allowed to slip on  
box, excessive belt wear will occur.  
2011 September  
800a3-NA  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12-OPERATION  
12.1 Operator's Correct Working Position and  
Operational Flow (Figure 12-1).  
12.3 Starting Production  
After having adjusted the machine according to the  
box dimensions (height-width), let the machine run  
without cartons and check its safety devices. Then  
start the working cycle.  
12.4 Tape Replacement and Threading  
Skill 1 - Operator  
See Manual 2: AccuGlide™ 3 High Speed 3 inch  
Taping Heads.  
Press the  
Figure 12-1  
LATCHING EMERGENCY STOP BUTTON.  
Once the box has been filled, close its top flaps and  
push it between the top and bottom drive belts.  
Always keep hands in position as shown in  
Figure 12-2.  
WARNING  
•
To reduce the risk associated with  
sharp blade hazards:  
The box will be automatically sealed with adhesive  
tape on the top and bottom box seams. Then the  
box will be expelled on the exit conveyor.  
− Keep hands and fingers away from  
tape cutoff blades under orange blade  
guards. The blades are extremely sharp.  
12.5 Box Size Adjustment  
Figure 12-2  
Repeat all the operations shown in  
Section 11 - Set-Up and Adjustments.  
Hand  
Position  
12.6 Cleaning  
Before carrying out any cleaning or maintenance  
operation stop the machine by Pushing the OFF (O)  
switch on the main and disconnect the electric power  
(Figure 12-3).  
12.2 Starting the Machine  
Important: Before starting the machine, verify that  
no tools or other objects are on the conveyor bed.  
12.7 Table of Operation Adjustments -  
Push the main switch ON (I) after the EMERGENCY  
Operator Qualifications  
BUTTON is released (Figure 12-3).  
1 Tape loading and threading  
2 Tape web alignment  
1
1
1
1
1
1
1
3 Adjustment of one way tension roller  
4 Adjustment to box size (H and W)  
5 Top flap compression rollers  
6 Adjustment of tape applying spring  
7 Conveyor bed height adjustment  
8 Special Adjustment-Changing tape leg length 2  
9 Special Adjustment-Column re-positioning  
2
12.8 Safety Devices Inspection  
1 Taping units blade guard  
2 Latching emergency stop button  
3 STOP (OFF) (O) main switch  
Figure 12-3  
2011 September  
800a3-NA  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12-OPERATION (continued)  
12.9 Troubleshooting Guide  
Problem  
Cause  
Correction  
Drive belts do not convey boxes  
Narrow boxes  
Check machine specifications.  
Boxes are narrower than  
recommended, causing slippage  
and premature belt wear.  
Worn drive belts  
Replace drive belts  
Top taping head does not apply  
enough pressure  
Adjust the box height adjustment  
with the crank  
Top flap compression rollers in too  
tight  
Readjust compression rollers  
Replace spring holder  
Taping head applying spring  
holder missing  
Taping head applying spring set  
too high  
Reduce spring pressure  
Drive belts do not turn  
Worn or missing friction rings  
Drive belt tension too low  
Electrical disconnect  
Replace friction rings  
Adjust belt tension  
Check power and electrical plug  
Evaluate problem and correct  
Motor not turning  
Drive belt break  
Worn belt  
Replace belt  
Excessive belt tension  
Dry column bearings  
Defective column bearings  
Squeaking noise as boxes pass  
through machine  
Tension to 3.5 kg [7 lbs] per  
adjustment section  
Lubricate column bearings  
Replace column bearings  
Reposition tape drum  
Tape not centered on box seam  
Tape drum not centered  
Box flaps not of equal length  
Check box specifications  
2011 September  
800a3-NA  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13-MAINTENANCE AND REPAIRS  
13.1 Safety Measures (see section 3)  
13.2 Tools and Spare Parts Supplied with  
the Machine  
Carrying out maintenance and repairs may imply  
the necessity to work in dangerous situations.  
See Spare Parts Order Section.  
13.3 Recommended Frequency of Inspection and Maintenance Operations  
Operation  
Frequency  
Qualification  
Sections  
Inspection safety features  
Cleaning of machine  
Cleaning of cutter blade  
Oiling of felt pad  
Lubrication  
Blade replacement  
Drive belt replacement  
daily  
weekly  
weekly  
weekly  
monthly  
when worn  
when worn  
1
1
2
2
2
2
2
13.4  
13.5  
13.6  
13.7  
13.7-13.8  
See Manual 2  
13.10  
13.7 Cleaning of Cutter Blade  
13.4 Inspections to be Performed Before and  
After Every Maintenance Operation  
Qualification 2  
Should tape adhesive build-up occur, carefully wipe  
clean with oily cloth or brush (Figure 13-1). Oil pre-  
vents the build-up of tape adhesive.  
Before every maintenance operation, Push the main  
switch OFF (O) and disconnect. During the mainte-  
nance operation, only properly trained and qualified  
personnel must work on the machine. At the end  
of every maintenance operation check the safety  
devices.  
(See Manual 2)  
13.5 Check Efficiency of Safety Features  
1. Blade guard assembly upper taping head  
2. Blade guard assembly lower taping head  
3. Latching Emergency stop button with mechanical  
lock (interrupt supply of electrical power)  
4. Push the main switch STOP/OFF (O)  
5. Safety guards top drive belts  
WARNING  
•
To reduce the risk associated with  
mechanical and electrical hazards:  
− Read, understand, and follow all safety and  
operating instructions before operating or  
servicing the case sealer.  
13.6 Cleaning of Machine  
− Allow only properly trained and qualified  
personnel to operate and service this  
equipment.  
Qualification 1  
A weekly cleaning with dry rags or diluted detergents  
is necessary. Cardboard boxes produce a significant  
quantity of dust and paper chips when processed  
or handled in case sealing equipment. If this dust is  
allowed to build up on machine components, it can  
cause component wear and over-heating of drive  
motors. The dust build up is best removed from the  
machine with a vacuum cleaner. Depending on the  
number of cartons processed, this cleaning should  
be done weekly. Excessive build-up that cannot be  
removed by vacuuming should be removed with a  
damp cloth.  
•
To reduce the risk associated with  
pinches, entanglement and hazardous  
voltage:  
− Turn electrical supply off and disconnect  
before performing any adjustments,  
maintenance or servicing the machine or  
taping heads.  
2011 September  
800a3-NA  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13-MAINTENANCE AND REPAIRS (continued)  
WARNING  
•
To reduce the risk associated with pinch, entanglement and hazardous voltage:  
− Turn electrical supply off and disconnect before performing any adjustments, maintenance or  
servicing the machine or taping heads  
13.8 Drive Belt Replacement  
Note – 3M recommends the replacement of drive belts in pairs, especially if belts are unevenly worn.  
Replacement - See Steps 1 thru 8  
Tension Adjustment - See Steps 3, 7 and 9.  
1. Crank the upper taping head to its fully raised position.  
2. Remove and retain the three (3) screws (A), three (3) washers (B) and side cover (C). See Figure 13-4.  
3. Remove and retain the screw (D), washer (E) and belt tensioner cover (F).  
4. Turn belt adjustment screws (G) counterclockwise on both the upper and lower tension assemblies until belt is  
loose. See Figure 13-5.  
5. Locate the belt lacing (joint) by turning the belt manually. Remove the pin with pliers. Remove and discard  
old belt.  
WARNING  
•
To reduce the risk associated with mechanical and electrical hazards:  
− Allow only properly trained and qualified personnel to operate and/or service this equipment  
A
B
C
D
E
F
Figure 13-4 – Box Drive Belt (Left Side View – Infeed End)  
2011 September  
800a3-NA  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13-MAINTENANCE AND REPAIRS (continued)  
WARNING  
•
To reduce the risk associated with pinch, entanglement and hazardous voltage:  
−
Turn electrical supply off and disconnect before performing any adjustments, maintenance or  
servicing the machine or taping heads  
G
G
G
Figure 13-5 – Box Drive Assembly, Infeed End  
6. Install the new belt around drive rollers and insert new pin. Pin must not extend beyond edge of belt.  
7. To set drive belt tension, turn adjustment screws (G) equally on both the upper and lower tension assemblies.  
Turn the screws clockwise to increase tension or counterclockwise to decrease tension. See Figure 13-5.  
Use a force gauge to pull the belt outward  
25mm [1 inch] at mid span, as shown with a moderate pulling force of 3.5 kg [7 lbs].  
8. Reverse procedures in Steps 1-3 (Figure 13-4) to reassemble the drive belt assembly.  
Important – Before installing new drive belt, check the belt inside surface for drive direction arrows and  
install belt accordingly. If no arrows are shown, the belt may be installed either way.  
13.9 Drive Pulley Rings  
Before installing a new belt, check the orange plastic  
drive pulley rings for wear. If torn, broken, or worn  
smooth, replace the rings (Figure 13-6).  
Figure 13-6  
28  
2011 September  
800a3-NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13-MAINTENANCE AND REPAIRS (continued)  
Drive Belt  
Direction  
Discharge End  
Infeed End  
25mm [2 Inch] Deflection  
@ 3.5 kg [7 lbs.] Pull Force at Midspan  
Box Drive Belt  
Figure 13-7 – Box Drive Belt Tension Adjustment, Top View  
WARNING  
• To reduce the risk associated with pinch, entanglement and hazardous voltage:  
− Turn electrical supply off and disconnect before performing any adjustments, maintenance or  
servicing the machine or taping heads  
13.10 Drive Belt Tension  
Tension adjustment of the drive belts may be required during normal operation. Belt tension must be adequate to  
positively move the box through the machine and they should run fully on the surface of the pulleys at each end of  
the frame. The idler pulleys on the infeed end are adjusted in or out to provide proper belt tension. Each belt is  
adjusted separately.  
Belt tension is obtained by tightening the adjustment screw so that a moderate pulling force of 3.5 kg [7 lbs]  
applied at the mid span, as shown in Figure 13-7, will deflect the belt 25mm [1 inch]. This will assure positive  
contact between the belt and the drive pulley on the discharge end of the taping head.  
To adjust belts, see "Maintenance – Drive Belts", steps 3 and 7.  
13.11 Special Set-Up Procedure  
WARNING  
• To reduce the risk associated with mechanical and electrical hazards:  
− Turn electrical and air supply off and disconnect before performing any adjustments, maintenance,  
or servicing the machine or taping heads  
The following changes to the case sealer will allow taping boxes 90mm [3-1/2 inches] minimum height.  
13.11.1 Case Sealer Frame  
(Refer to Figure 13-8A)  
1. Raise the upper head assembly (by turning crank handle counterclockwise). Remove and retain the two  
screws and washers from the normal position holes "A-A".  
2. Remount and secure the stop bracket in the lower position "A" using the top holes and original fasteners. Re-  
locate both the right and left stop brackets.  
2011 September  
800a3-NA  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13-MAINTENANCE AND REPAIRS (continued)  
13.11.2 Taping Heads  
(Refer to Figure 13-8B and Figure 13-8C)  
Taping Head Adjustments  
WARNING  
•
To reduce the risk associated with sharp blade hazards:  
−
Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are  
extremely sharp  
TAPE WEB ALIGNMENT – Manual 2  
TAPE DRUM FRICTION BRAKE – Manual 2  
APPLYING MECHANISM SPRING – Manual 2  
ONE-WAY TENSION ROLLER – Manual 2  
TAPE LEG LENGTH  
Leading Tape Leg Length Adjustment – Manual 2  
Changing Tape Leg Length from 70 to 48mm [2-3/4 to 2 inches] – Manual 2  
Note – Changing tape leg to 48mm [2 inches] requires machine adjustment also. See  
"Special Set-Up Procedure – Changing Tape Leg Length".  
1. Loosen, but do not remove, the two (2) retaining screws that secure the upper taping head shown in Figure 13-8B.  
B
C
A
Figure 13-8 – Removing Taping Heads From Case Sealer  
30  
2011 September  
800a3-NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13-MAINTENANCE AND REPAIRS (continued)  
13.11.2 Special Set-Up Procedure (continued)  
A
B
C
D
WARNING  
•
To reduce the risk associated with  
muscle strain:  
− Use proper body mechanics when  
removing or installing taping heads that  
are moderately heavy or may be  
considered awkward to lift  
2. Slide the head forward and lift straight up to  
remove it from the case sealer.  
3. Lift the lower taping head, shown in  
Figure 13-8C, straight up to remove it from the  
case sealer bed.  
4. Refer to Manual 2 (Taping Head), See  
"Adjustments – Changing Tape Leg Length"  
for taping head set-up.  
13.13.3 Drive Belt Assembly Height  
The drive belt assemblies can be raised 48mm  
[2 inches] to provide better conveying of tall boxes.  
This change increases the minimum box height that  
can be taped to 190mm [7-1/4 inches].  
Figure 13-9 – Drive Belt Assembly, Disassembly  
Disassemble – Figure 13-9  
A
B
D
1. It is first necessary to raise the top taping head.  
Utilize the height adjustment crank and move  
the upper taping head to the fully raised position.  
2. Remove and retain the screw (A), cap washer  
(B) and spacer (C) from the front and rear arm  
assembly pivots.  
3. Lift belt drive assembly (D) up off the arm  
assembly pivots.  
C
Reassemble – Figure 13-10  
4. Reassemble the spacer (C) onto the front and  
rear arm assembly pivots.  
5. Install the belt drive assembly (D) onto the pivots  
and secure with the cap washers (B) and screws  
(A).  
Note – Both drive belt assemblies must be  
installed at the same operating height.  
Figure 13-10 – Drive Belt Assembly, Reassembly  
2011 September  
800a3-NA  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13-MAINTENANCE AND REPAIRS (continued)  
Special Set-Up Procedure (continued)  
WARNING  
WARNING  
• To reduce the risk associated with  
• To reduce the risk associated with  
mechanical and electrical hazards:  
muscle strain:  
− Use the appropriate rigging and  
− Turn electrical and air supply off and  
disconnect before performing any  
adjustments, maintenance, or servicing the  
machine or taping heads  
material handling equipment when lifting or  
repositioning this equipment  
− Use proper body mechanics when  
removing or installing taping heads that are  
moderately heavy or may be considered  
awkward to lift  
13.11.4 Box Height Range  
(Outer Column – Re-Positioning)  
To Re-position the outer columns:  
1. Remove special nut from the bottom of each  
Moving the outer columns to the upper set of  
mounting holes increases the maximum box size  
(height) handled by the case sealer from 620mm  
[24-1/2 inches] to 725mm [28-1/2 inches]. Note –  
this also increases the minimum box height from  
120 mm [4-3/4 inches] to 210mm [8-1/4 inches].  
column lead screw - Figure 13-11A.  
2. Remove plastic column cap from the top of each  
outer column as shown in Figure 13-11B.  
3. Crank upper assembly up, out of plastic nuts.  
Lift upper assembly up and out of outer columns.  
Be careful not to damage lead screws.  
Figure 13-11C.  
2011 September  
800a3-NA  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13-MAINTENANCE AND REPAIRS (continued)  
13.11.4 Special Set-Up Procedure (continued)  
Upper Assembly  
Plastic  
B
Column  
Cap  
C
Outer  
Column  
Plastic  
Nut  
A
Lead  
Screw  
Special  
Nut  
Figure 13-11 – Upper Frame Removal  
2011 September  
800a3-NA  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13-MAINTENANCE - SPECIAL SET-UP (continued)  
13.11.4 Special Set-Up Procedure (continued)  
Important – Before removing chain, mark  
both front and rear sprockets/chain with  
chalk or paint to be sure sprockets/chain  
when re-assembled, will be in same position  
as before disassembly. Figure 13-13A and  
Figure 13-11B. Do not rotate sprockets  
once chain is removed. (This would result in  
the right and left drive assemblies not being  
parallel.)  
4. Remove M6 x 16 hex hd screw, special washer  
and drive belt width adjustment crank -  
Figure 13-12.  
5. Remove side covers (2) from each side of ma-  
chine bed - Figure 13-12.  
6. Remove chain. If necessary, slip width  
adjustment crank on shaft and rotate until chain  
master link is in convenient position for removal.  
Remove chain master link and remove chain.  
Figure 13-13C.  
C
M6 X 16  
Hex Hd Screw  
Master  
Link  
Washer  
A
Crank  
Side Covers  
B
Mark Chain  
and Sprocket  
Mark Chain  
and Sprocket  
Figure 13-12 – Crank/Chain Guards  
Figure 13-13 – Chain Removal  
2011 September  
800a3-NA  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13-MAINTENANCE - SPECIAL SET-UP (continued)  
13.11.4 Special Set-Up Procedure (continued)  
7. Remove fasteners (M8 x 16 socket head screws  
and M6 plain washers) that attach column  
spacers to machine bed and remove spacers/  
outer columns from machine bed. Figure 13-  
14A.  
Note – When installing upper assembly  
back into machine (removed in Step 3), slide  
upper assembly down into outer columns  
until lead screws contact plastic nuts and  
support upper assembly. Then, slowly turn  
height adjustment crank counterclockwise  
until two "clicks" are heard, one at each  
plastic nut. Now the upper assembly can be  
cranked down (turn height adjustment crank  
clockwise) for installation of special nut on  
bottom of each lead screw.  
8. Remove fasteners (M8 x 20 socket head  
screws) that attach spacers to columns, move  
spacer down 100mm [4 inches] to lower set  
of mounting holes and re-attach spacers to  
columns. Figure 13-14B.  
9. Reverse procedure to reassemble machine.  
A
B
Outer  
Column  
Column  
Spacer  
Outer  
Column  
Column  
Spacer  
Figure 13-14 – Column Spacers/Columns  
2011 September  
800a3-NA  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13-MAINTENANCE AND REPAIRS (continued)  
13.12 List of the Maintenance Operations  
Date:  
Description of Operation  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
________________________________________________________________  
2011 September  
800a3-NA  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14-ADDITIONAL INSTRUCTIONS  
15-ENCLOSURES / SPECIAL INFO.  
14.1 Information for Disposal of Machine (ELV)  
The machine is composed of the following materials:  
- Steel structure  
- Nylon rollers  
- Drive belts in PVC  
- Nylon pulleys  
For machine disposal, follow the regulations  
published in each country.  
14.2 Emergency Procedures  
Figure 14-1  
In case of danger/fire:  
Disconnect plug of power cable from power supply.  
(Figure 14-1)  
IN CASE OF FIRE  
Use a fire extinguisher that is rated for electrical fires  
(Figure 14-2).  
15.1 Statement of Conformity  
Not Applicable.  
15.2 Emission of Hazardous Substances  
Figure 14-2  
Nothing to report  
2011 September  
800a3-NA  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16-TECHNICAL DIAGRAMS  
16.1 Electric Diagram  
2011 September  
800a3-NA  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16-TECHNICAL DOCUMENTATION AND INFORMATION (continued)  
16.2 Spare Parts Order  
Replacement Parts Ordering Information and Service  
Refer to the first page of this instruction manual "Replacement Parts and Service Information".  
Order parts by quoting the following information:  
(Refer to the Identification Plate on the Machine)  
•
•
•
•
•
•
•
MACHINE MODEL  
SERIAL NUMBER  
FIGURE NO.  
POSITION  
3M PART NO. (11 DIGITS)  
DESCRIPTION  
QUANTITY  
Refer to Manual 2 for recommended taping head spare parts.  
Important!  
The machine is constantly revised and improved by our designers. The spare parts catalogue is also periodically  
updated. It is very important that all the orders of spare parts make reference to the serial number of the machine  
(located on the identification plate on the machine)
The manufacturer reserves the right to modify the machine at any time without notice.  
It is suggested that the following spare parts be ordered and kept on hand.  
800a3  
Qty.  
3M-Part Number  
Description  
2
78-8076-5452-6  
Belt-Drive W/Hook  
Tool Kit  
A tool kit, part number TBA, is available as a stock item. The kit contains the necessary open end and hex socket  
wrenches for use with the metric fasteners on the case sealer. The threading tool, part number  
78-8076-4726-4, contained in above kit is also available as a replacement stock item.  
Label Kit  
In the event that any labels are damaged or destroyed, they must be replaced to ensure operator safety. A label  
kit, part number 78-8060-8476-6, is available as a stock item. It contains all the safety labels used on the  
800a3 Adjustable Case Sealer.  
2011 September  
800a3-NA  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3 Adjustable Case Sealer, Type 40800  
Frame Assemblies  
To Order Parts:  
1. Refer to first illustration, Frame Assemblies, for the Figure Number that identifies a specific portion of the  
machine.  
2. Refer to the appropriate Figure or Figures to determine the parts required and the parts reference number.  
3. The Parts List that follows each illustration, includes the Reference Number, Part Number and Part  
Description for the parts on that illustration.  
Note – The complete description has been included for standard fasteners and some commercially  
available components. This has been done to allow obtaining these standard parts locally, if desired.  
4. Order parts by Part Number, Part Description and Quantity required. Also include the model/machine name,  
machine type, and serial number that are located on the identification plate.  
5. Refer to the first page of this instruction manual “Replacement Parts and Service Information” for  
replacement parts ordering information.  
Important – Not all the parts listed are normally stocked items. Some parts or assemblies shown are  
available only on special order. Contact 3M/Tape Dispenser Parts to confirm item availability.  
Options and Accessories  
For additional information on the options and accessories listed below, contact your 3M Representative.  
Part Number  
Option/Accessory  
78-8052-6553-1  
78-8069-3983-7  
78-8069-3924-1  
70-0064-4965-9  
70-0064-4964-2  
78-8069-3926-6  
78-8095-4852-8  
78-8095-4853-6  
78-8114-0940-4  
Box Hold Down Attachment  
Caster Kit Attachment  
Conveyor Extension Attachment  
AccuGlide™ 3 Upper Taping Head - 3 inch, Type 10800  
AccuGlide™ 3 Lower Taping Head - 3 inch, Type 10800  
Low Tape Sensor Kit  
3-Inch Tape Edge Fold Attachment, Upper Head  
3-Inch Tape Edge Fold Attachment, Lower Head  
Three Flap Folder Kit  
2011 September  
800a3-NA  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3 Adjustable Case Sealer  
Figure 10514  
Figure 6166  
Figure 3269  
Figure 5350  
Figure 6172  
Figure 15231  
Figure 6171  
Figure 6170  
Figure 5817  
Frame  
Assemblies  
2011 September  
800a3-NA  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
1
1
5
7
16  
18  
3
16  
18  
20  
22  
11  
8
20  
6
9
25  
21  
12  
15  
13  
14  
10  
11  
11  
2
19  
18  
2
4
7
17  
20  
Figure 10514  
2011 September  
800a3-NA  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
Figure 10514  
Ref. No.  
3M Part No.  
Description  
10514-1  
10514-2  
10514-3  
10514-4  
10514-5  
10514-6  
10514-7  
10514-8  
10514-9  
10514-10  
10514-11  
10514-12  
10514-13  
10514-14  
10514-15  
10514-16  
10514-17  
10514-18  
10514-19  
10514-20  
10514-21  
10514-22  
78-8070-1564-5  
78-8070-1565-2  
78-8070-1566-0  
78-8070-1395-4  
78-8070-1568-6  
78-8060-8462-6  
78-8017-9169-6  
78-8098-8829-6  
78-8098-8828-8  
78-8098-8830-4  
26-1002-5753-9  
78-8060-8172-1  
78-8052-6271-0  
78-8100-1048-4  
78-8017-9077-1  
78-8032-0375-7  
78-8070-1215-4  
26-1000-0010-3  
78-8010-7169-3  
78-8133-9641-9  
26-1004-5510-9  
78-8097-8816-3  
Tape Roll Bracket Assembly  
Tape Drum Bracket Assembly  
Bracket – Tape Drum  
Bracket – Bushing Assembly  
Cap – Bracket  
Shaft – Tape Drum, 3 Inch Head  
Nut – M18 x 1  
Tape Drum Sub Assembly –3 Inch Wide  
Tape Drum  
Leaf Spring  
Screw – Self Tapping  
Washer – Friction  
Washer – Tape Drum  
Spring – Core Holder  
Nut – Self-Locking, M10 x 1  
Screw – Hex Hd M6 x 16  
Spacer – Stud  
Washer – Flat M6  
Screw – Hex Hd M6 x12  
Tape Drum Assembly – 3 Inch Head  
Washer – Plain, M10  
Latch - Tape Drum  
2011 September  
800a3-NA  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
40  
47  
41  
31  
37  
15  
28  
27  
34  
49  
50  
38  
7
41  
46  
34  
36  
8  
35  
45  
43  
33  
26  
28  
29  
32  
25  
39  
42  
44  
24  
30  
23  
21  
7
22  
13  
14  
5
38  
7
15  
13  
12  
6
8
16  
11  
4
1
3
9
19  
10  
17  
18  
1
3
20  
2
2
Figure 3269  
2011 September  
800a3-NA  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
Figure 3269  
Ref. No.  
3M Part No.  
Description  
3269-1  
3269-2  
3269-3  
3269-4  
3269-5  
3269-6  
3269-7  
3269-8  
78-8060-8489-9  
78-8076-5426-0  
26-1003-7964-8  
78-8017-9318-9  
78-8060-8491-5  
26-1002-4955-1  
78-8005-5740-3  
78-8060-8492-3  
78-8076-5482-3  
78-8060-8087-1  
78-8060-8494-9  
78-8060-8495-6  
78-8054-8617-8  
78-8054-8589-9  
26-1003-6916-9  
78-8060-8496-4  
78-8054-8969-3  
78-8054-8970-1  
78-8054-8571-7  
78-8054-8968-5  
78-8054-8585-7  
78-8054-8586-5  
78-8054-8584-0  
78-8054-8583-2  
78-8060-8497-2  
78-8059-5617-0  
78-8060-8498-0  
78-8060-8499-8  
26-1003-7946-5  
78-8076-4818-9  
78-8113-6803-0  
78-8060-7878-4  
78-8070-1503-3  
78-8042-2919-9  
26-1003-5829-5  
26-1000-0010-3  
78-8076-5428-6  
78-8010-7157-8  
78-8070-1505-8  
78-8070-1506-6  
78-8076-4807-2  
78-8076-5422-9  
78-8070-1509-0  
26-1005-5316-8  
78-8070-1510-8  
78-8070-1511-6  
78-8070-1512-4  
78-8076-4800-7  
78-8076-4821-3  
78-8076-4809-8  
78-8054-8821-6  
Column – Outer  
Plate  
Screw – Soc Hd, M8 x 20  
Washer – Plain 8 mm  
Cap – Column  
Screw – Self-Tap, 8P x 13  
Washer – Plain 4 mm  
Stop – Height  
Plate – Nut Stop  
Screw – M5 x 10  
Column Assembly – Inner  
Column – Inner  
Bearing – Special  
Screw – Special  
Nut – Locking, M6, Plastic Insert  
Lead Screw  
Spring  
Bed Plate For Spring  
Nut – Plastic  
Nut – Special  
3269-9  
3269-10  
3269-11  
3269-12  
3269-13  
3269-14  
3260-15  
3269-16  
3269-17  
3269-18  
3269-19  
3269-20  
3269-21  
3269-22  
3269-23  
3269-24  
3269-25  
3269-26  
3269-27  
3269-28  
3269-29  
3269-30  
3269-31  
3269-32  
3269-33  
3269-34  
3269-35  
3269-36  
3269-37  
3269-38  
3269-39  
3269-40  
3269-41  
3269-42  
3269-43  
3269-44  
3269-45  
3269-46  
3269-47  
3269-48  
3269-49  
3269-50  
3269-51  
Collar  
Pin  
Spacer  
Bushing  
Bushing – Lead Screw  
Set Screw – M6 x 8  
Bushing – Inner Column  
Sprocket – 3/8 Inch, Z=13  
Screw – Soc Hd, M4 x 25  
Chain – 3/8 Inch, Pitch 197  
Housing – Chain, W/English Language Label  
Idler Screw  
Roller – Chain Tensioning  
Washer – Triple, M6  
Screw – Hex Hd, M6 x 12  
Washer – Flat M6  
Cover  
Screw – Hex Hd, M4 x 10  
Cap – Inner Column  
Cover – Screw  
Crank Assembly  
Crank  
Shaft – Crank  
Screw – Flat Hd Hex Dr, M5 x 16  
Washer – Nylon, 7 x 15 x 1  
Bushing  
Knob – VTR-B-M12  
Washer – Crank  
Key – Stop  
Washer – Crank  
End – Cap  
2011 September  
800a3-NA  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
1
2
2
Figure 5350  
2011September  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
Figure 5350  
Ref. No.  
3M Part No.  
Description  
5350-1  
5350-2  
5350-3  
5350-4  
5350-5  
5350-6  
5350-7  
5350-8  
5350-9  
5350-10  
5350-11  
5350-12  
5350-13  
5350-14  
5350-15  
78-8100-0876-9  
78-8100-0877-7  
78-8070-1559-5  
78-8054-8974-3  
78-8070-1560-3  
26-1004-5510-9  
78-8070-1561-1  
26-1004-5507-5  
26-1003-5841-0  
78-8017-9074-8  
78-8070-1562-9  
12-7991-1752-3  
78-8070-1563-7  
78-8070-1549-6  
26-1003-6918-5  
Compression Roller Assembly – R/H  
Compression Roller Assembly – L/H  
Support – Compression Roller  
Pressure Roller  
Stud – Roller Mounting  
Washer – Friction M10  
Nut – M10  
Washer – M8  
Screw – M8 x 16  
Washer – Nylon, 15 mm  
Tube – Roller Support  
Washer – Plain, M14  
Screw – M10 x 80  
Knob – VTR-B-M10  
Nut – Plastic Insert, M10 Hex Flange  
2011 September  
800a3-NA  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
27  
18  
3
3
18  
6
17  
21  
6
2
9
13  
14  
18  
15  
18  
7
6
5
4
11  
10  
3
12  
8
20  
19  
2
1
16  
17  
24  
26  
22  
23  
21  
Figure 5817  
25  
2011 September  
800a3-NA  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
Figure 5817  
Ref. No.  
3M Part No.  
Description  
5817-1  
78-8094-6379-3  
78-8113-6759-4  
78-8094-6381-9  
78-8005-5740-3  
26-1003-6914-4  
78-8076-4715-7  
78-8076-5211-6  
78-8094-6382-7  
78-8028-8208-0  
78-8017-9018-5  
78-8094-6383-5  
78-8076-5378-3  
78-8094-6384-3  
78-8076-4968-2  
78-8028-7909-4  
78-8100-1038-5  
78-8060-8053-3  
26-1003-7957-2  
26-1000-0010-3  
78-8076-5194-4  
78-8094-6386-8  
78-8100-1039-3  
78-8017-9257-9  
78-8060-8087-1  
78-8010-7417-6  
26-1014-5845-8  
78-8100-1234-0  
78-8114-4896-4  
Support – Box  
5817-2  
Box – W/English Language Label  
Screw – Soc Hd, Hex Hd, M4 x 15  
Washer – Plain, 4 mm  
Nut – Plastic Insert, M4  
Cord Grip  
5817-3  
5817-4  
5817-5  
5817-6  
5817-7  
Set Nut – GMP 13.5  
Guide – Mounting  
5817-9  
5817-10  
5817-11  
5817-12  
5817-13  
5817-14  
5817-15  
5817-16  
5817-17  
5817-18  
5817-19  
5817-20  
5817-21  
5817-22  
5817-23  
5817-24  
5817-25  
5817-26  
5817-27  
5817-31  
5817-33  
Screw – 6P x 9,5  
Washer – Plain, M4  
Contactor - Allen Bradley m05  
Circuit Breaker - Allen Bradley 140m -C2E  
Clamp – VGPE 4/6  
Terminal  
Power Cord U.S.A.  
Cable – 3 x 20 AWG, 5 MT  
Wire – 3-Pole, 5 Meters Length  
Screw – Soc Hd, Hex Hd, M6 x 16  
Washer – Flat, M6  
Box – E-Stop  
Switch – On/Off,
Support – On/Off Switch  
Screw – Phillips Hd, M4 x 10  
Screw – M5 x 10  
Nut – Hex, M5  
E-Stop
Collar  
Box – On/Off, Grey  
2011 September  
800a3-NA  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
14  
13  
57  
63  
58  
59  
60  
61  
7
62  
48  
45  
49  
12  
48  
45  
44  
45  
9
11  
15  
10  
46  
47  
48  
9
6
5
10  
45  
43  
39  
9
40  
10  
45  
23  
16  
52  
19  
42  
8
41  
17  
51  
50  
8
9
33  
35  
8
34  
21  
22  
9
20  
18  
21  
22  
56  
53 54  
67  
68  
10  
9
55  
3
4
Figure 15231 / 1  
2011 September  
800a3-NA  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
Figure 15231 / 1  
Ref. No.  
3M Part No.  
Description  
15231-1  
78-8100-1205-0  
78-8100-1206-8  
78-8100-1207-6  
78-8100-1208-4  
78-8113-6818-8  
78-8113-6819-6  
78-8091-0500-6  
78-8055-0661-1  
26-1003-5829-5  
26-1000-0010-3  
78-8094-6109-4  
78-8023-2334-1  
78-8070-1522-3  
26-1011-8828-7  
78-8070-1523-1  
78-8094-6174-8  
78-8076-5439-3  
78-8060-7886-7  
78-8046-8135-7  
78-8137-0934-8  
78-8057-5834-5  
78-8057-5835-2  
78-8076-5440-1  
78-8076-5441-9  
78-8052-6713-1  
78-8055-0669-4  
78-8057-5739-6  
78-8055-0668-6  
78-8091-0382-9  
78-8076-5442-7  
26-0001-5862-1  
78-8054-8877-8  
78-8137-0935-5  
78-8076-4933-6  
Drive Assembly – R/H W/O Motor  
Drive Assembly – L/H W/O Motor  
Guide – Lower, R/H  
15231-2  
15231-3  
15231-4  
Guide – Lower, L/H  
15231-5  
Guide – Upper, R/H, W/English Language Label  
Guide – Upper, L/H, W/English Language Label  
Bushing – Side Drive  
15231-6  
15231-7  
15231-8  
Spacer  
15231-9  
Screw – Hex Hd, M6 x 12  
Washer – Flat M6  
15231-10  
15231-11  
Support – Gearmotor  
15231-12  
Screw – Soc Hd, Hex Soc, M6 x 25  
Gearmotor – Bodine, 42X5BFCI-E2, 15:1, 115V, 60 Hz  
Capacitor – 15μF, 300VAC, Motor Run  
Screw – 1/4 - 28 x 1/2 SHCS  
Extension – Gearmotor  
Flange Assembly  
15231-13  
15231-14  
15231-15  
15231-16  
15231-17  
15231-18  
Screw – Hex Hd, M6 x 16, Special  
Key – 5 x 5, 12 mm  
15231-19  
15231-20  
Sprocket 3/8'’ Z17  
15231-21  
Tab Washer  
15231-22  
Centering Washer  
15231-23  
Pulley Assembly – Drive  
Roller – Drive  
15231-24  
15231-25  
Ring – Polyurethane  
15231-26  
Shaft – Pulley Keyed  
15231-27  
Key – M5 x 5 x 30 mm  
15231-28  
Washer – 15/26 x 1  
15231-29  
Belleville Washer – /16  
Flange Assembly  
15231-30  
15231-31  
Screw – Flat Hd Soc, M5 x 12  
Washer – 5,5/20 x 4  
15231-32  
15231-33  
Sprocket 3/8'' Z20  
15231-34  
Chain – 3/8 Inch Pitch, 52 Pitch  
2011 September  
800a3-NA  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
66  
65  
64  
66  
65  
64  
1
2
23  
31  
35  
32  
38  
30  
24  
24  
29  
25  
25  
36  
28  
26  
37  
27  
19  
30  
Figure 15231 / 2  
2011 September  
800a3-NA  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
Figure 15231 / 2  
Ref. No.  
3M Part No.  
Description  
15231-35  
78-8076-5443-5  
78-8055-0660-3  
78-8076-5444-3  
12-7997-0272-0  
78-8076-5445-0  
78-8076-5446-8  
78-8070-1519-9  
78-8017-9318-9  
78-8076-5448-4  
78-8055-0850-0  
78-8005-5740-3  
78-8100-1211-8  
78-8100-1212-6  
26-1002-5753-9  
78-8100-1213-4  
78-8100-1214-2  
78-8100-1215-9  
78-8076-5255-3  
78-8091-0764-8  
78-8091-0765-5  
78-8010-7165-1  
78-8076-5452-6  
78-8060-7631-7  
78-8076-5197-7  
78-8060-7626-7  
78-8060-7877-6  
78-8060-7875-0  
78-8060-8053-3  
78-8076-4968-2  
78-8076-5453-4  
78-8054-8577-4  
26-1001-9843-6  
78-8010-7210-5  
78-8137-0932-2  
78-8137-0933-2  
Pulley Assembly – Idler  
Roller – Idler  
15231-36  
15231-37  
Shaft – Idler Pulley  
E-Ring – M-25  
15231-38  
15231-39  
Tensioning – Belt  
15231-40  
Washer – Shaft  
15231-41  
Screw – Soc Hd, Hex Hd, M8 x 70  
Washer – Plain 8 mm  
Cover – Belt Tensioner  
Screw – Cap, M4 x 6  
Washer – Plain 4 mm  
Cover – Drive, R/H  
Cover – Drive, L/H  
Screw – Self-Tapping  
Guard – Belt  
15231-42  
15231-43  
15231-44  
15231-45  
15231-46  
15231-47  
15231-48  
15231-49  
15231-50  
Guard – Rubber  
15231-51  
Guard – Metal  
15231-52  
Screw – Phillips Hd, M4 x 12  
Cover – Chain, Right  
Cover – Chain, Left  
Screw – Flat Hd Soc, M5 x 25  
Belt – Box Drive  
15231-53  
15231-54  
15231-55  
15231-56  
15231-57  
Connector – 3/8 Inch  
Sleeving – /12, 800 mm  
Connector – PG 11/12  
Plug Housing – Vertical  
Plug Male  
15231-58  
15231-59  
15231-60  
15231-61  
15231-62  
Wire – 3-Pole, 5 Meters Length  
Terminal  
15231-63  
15231-64  
Roller  
15231-65  
Washer – Special  
15231-66  
Screw – Flat Soc Hd, M6 x 16  
Screw - Tensioner  
15231-67  
15231-68  
Tensioner - Pulley R/H  
Tensioner - Pulley L/H  
57  
2011 September  
800a3-NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
10  
9
5
6
4
8
5
8
6
11  
7
8
2
7
8
1
3
12  
13  
2
Figure 6166  
2011 September  
800a3-NA  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
Figure 6166  
Ref. No.  
3M Part No.  
Description  
6166-1  
6166-2  
6166-3  
6166-4  
6166-5  
6166-6  
6166-7  
6166-8  
6166-9  
6166-10  
6166-11  
6166-12  
6166-13  
78-8100-1218-3  
78-8060-7758-8  
26-1003-7963-0  
78-8076-4636-5  
78-8010-7163-6  
78-8005-5741-1  
78-8010-7417-6  
78-8060-7631-7  
78-8060-8154-9  
78-8060-8029-3  
78-8100-1219-1  
78-8017-9018-5  
78-8010-7157-8  
Housing – Wire  
Fairlead – /20  
Screw – Soc Hd, M8 x 16  
Strap – Wire  
Screw – Hex Hd, M5 x 10  
Washer – Flat, M5  
Nut – Hex, M5  
Connector – 3/8 Inch  
Sleeving – 0,90 MT  
Clamp – 140 x 3,5  
Cover – Housing  
Washer – Plain, M4  
Screw – Hex Hd, M4 x 10  
2011 September  
800a3-NA  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
48  
22  
7
38  
42  
43  
15  
A
13  
14  
36  
16  
41  
47  
1
47  
32  
A
34  
39  
31  
28  
33  
9
7
40  
32  
2
35  
32  
37  
24  
29  
7
33  
46  
45  
33  
46  
45  
44  
9
9
30  
11  
12  
2
Figure 6170 / 1  
2011 September  
800a3-NA  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
Figure 6170 / 1  
Ref. No.  
3M Part No.  
Description  
6170-1  
78-8076-5380-9  
78-8076-5381-7  
78-8076-5382-5  
78-8060-8480-8  
78-8055-0867-4  
78-8017-9313-0  
78-8017-9318-9  
78-8076-5383-3  
26-1003-7963-0  
78-8060-8481-6  
78-8052-6676-0  
78-8052-6677-8  
78-8060-7693-7  
78-8076-5384-1  
78-8076-5385-8  
78-8094-6100-3  
78-8076-5387-4  
78-8091-0780-4  
78-8091-0781-2  
26-1003-5828-7  
78-8076-5389-0  
78-8094-6101-1  
78-8076-5391-6  
78-8076-5462-5  
78-8076-4758-7  
78-8076-4759-5  
78-8076-5030-0  
Bed – Conveyor  
6170-2  
Leg Assembly – Inner, W/Stop  
Leg – Inner  
6170-3  
6170-4  
Pad – Foot  
6170-5  
Screw – Hex Hd, M8 x 30  
Nut – Self-Locking, M8  
Washer – Plain 8 mm  
Stop – Leg  
6170-6  
6170-7  
6170-8  
6170-9  
Screw – Soc Hd, M8 x 16  
Label – Height  
6170-10  
6170-11  
6170-12  
6170-13  
6170-14  
6170-15  
6170-16  
6170-17  
6170-18  
6170-19  
6170-20  
6170-21  
6170-22  
6170-23  
6170-24  
6170-25  
6170-26  
6170-27  
Clamp – Outer  
Clamp – Inner  
Roller – 32 x 38  
Shaft – Roller  
Spring  
Conveyor Assembly – Front  
Conveyor – Front  
Shaft – Central Roller  
Shaft – Side Roller  
Screw – Hex Hd, M6 x 10  
Mounting – Conveyor  
Conveyor Assembly – Rear  
Conveyor – Rear  
Support – Tape Drum  
Support – Tape Bracket  
Shaft – Roller  
Roller – Knurled, L=114  
2011 September  
800a3-NA  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
16  
22  
13  
13  
23  
17  
19  
21  
19  
21  
18  
18  
20  
20  
24  
25  
26  
29  
28  
27  
49  
2
52  
51  
3
6
10  
8
7
50  
4
9
OPTIONAL  
5
Figure 6170 / 2  
62  
2011 September  
800a3-NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
Figure 6170 / 2  
Ref. No.  
3M Part No.  
Description  
6170-28  
6170-29  
6170-30  
6170-31  
6170-32  
6170-33  
6170-34  
6170-35  
6170-36  
6170-37  
6170-38  
6170-39  
6170-40  
6170-41  
6170-42  
6170-43  
6170-44  
6170-45  
6170-46  
6170-47  
6170-48  
6170-49  
6170-50  
6170-51  
6170-52  
78-8032-0375-7  
26-1000-0010-3  
26-1003-7957-2  
78-8060-8487-3  
78-8060-8087-1  
78-8010-7417-6  
78-8076-5393-2  
78-8076-5394-0  
78-8076-5395-7  
78-8076-5396-5  
78-8100-1203-5  
78-8113-6813-9  
78-8076-4517-7  
78-8060-7876-8  
78-8028-8208-0  
78-8060-7873-5  
78-8060-8488-1  
78-8046-8217-3  
78-8005-5741-1  
78-8076-4500-3  
26-1003-5841-0  
78-8098-9076-3  
26-1009-9096-4  
26-1009-9094-9  
26-1009-9095-6  
Screw – Hex Hd, M6 x 16  
Washer – Flat M6  
Screw – Soc Hd Hex Hd, M6 x 16  
Cover – Switch  
Screw – M5 x 10  
Nut – Hex M5  
Plate – Tape Bracket Support  
Spacer  
Cover – Side, Front, R/H  
Cover – Side, Front, L/H  
Cover – Side, Rear, R/H  
Cover – Side, Rear, L/H, W/English Language Label  
End Cap – /22 x 1  
Cover – Plug Lateral  
Screw – 6P x 9,5  
Plug – Female  
Screw – Hex Hd, M5 x 20  
Washer – Special  
Washer – Plain M5  
Stud – Mounting  
Screw – M8 x 16  
Caster Assembly  
Caster – Dual Locking  
Washer – Spring, Helical, M12  
Nut – M12  
2011 September  
800a3-NA  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
29  
Front  
28  
27  
54  
14  
52  
53  
1
18  
54  
53  
24  
24  
26  
36  
9
23  
9
19  
18  
37  
10  
21  
20  
20  
21  
19  
22  
38  
39  
15  
9
25  
9
26  
27  
29  
28  
33  
34  
28  
28  
2
32  
31  
30  
35  
1
2
11  
11  
8
8
3
3
7
7
5
6
7
7
4
4
9
9
13  
12  
13  
12  
Figure 6171 / 1  
10  
10  
2011 September  
800a3-NA  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
Figure 6171 / 1  
Ref. No.  
3M Part No.  
Description  
6171-1  
78-8100-1229-0  
78-8100-1230-8  
78-8076-5401-3  
78-8076-5402-1  
78-8076-5403-9  
78-8076-5404-7  
78-8076-5405-4  
78-8076-5239-7  
26-1000-0010-3  
26-1003-6916-9  
78-8100-1220-9  
26-1003-5842-8  
78-8017-9318-9  
78-8076-5407-0  
78-8076-5408-8  
78-8076-5409-6  
78-8076-5410-4  
78-8076-5411-2  
78-8076-5412-0  
78-8060-8010-3  
78-8076-5413-8  
78-8076-5414-6  
78-8076-5415-3  
26-1003-7946-5  
78-8076-5416-1  
78-8023-2334-1  
78-8076-5417-9  
Shaft Assembly – Drive R/H  
Shaft Assembly – Drive L/H  
Block – Upper  
6171-2  
6171-3  
6171-4  
Block – Lower  
6171-5  
Nut – Block, R/H  
6171-6  
Nut – Block, L/H  
6171-7  
Bushing – Block  
6171-8  
Screw – Hex Hd, M6 x 50  
Washer – Flat M6  
6171-9  
6171-10  
6171-11  
6171-12  
6171-13  
6171-14  
6171-15  
6171-16  
6171-17  
6171-18  
6171-19  
6171-20  
6171-21  
6171-22  
6171-23  
6171-24  
6171-25  
6171-26  
6171-27  
Nut – Locking, Plastic Insert M6  
Shaft – Drive Mount  
Screw – Hex Hd, M8 x 20  
Washer – Plain 8 mm  
Screw – R/H  
Screw – L/H  
Screw – Handle, R/H  
Screw – Handle, L/H  
Spacer – Screw  
Flange – W/Bearing  
Snap Ring – 42 mm Shaft  
Spring  
Coupling – Screw, Female  
Coupling – Screw, Male  
Screw – Soc Hd, M4 x 25  
Spacer – Hex, 10 x 107  
Screw – Soc Hd, Hex Soc, M6 x 25  
Spacer  
2011 September  
800a3-NA  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
51  
29  
Rear  
28  
27  
54  
53  
16  
1
52  
18  
54  
53  
24  
21  
24  
20  
26  
19  
23  
9
19  
20  
21  
18  
22  
17  
25  
9
26  
27  
29  
33 28  
28  
35  
34  
28  
1
32  
40  
50  
31  
49  
30  
2
1
11  
11  
8
8
40  
41  
43  
3
3
5
6
42  
44  
7
7
45  
46  
48  
7
7
47  
4
4
9
10  
9
10  
13  
12  
13  
12  
Figure 6171 / 2  
800a3-NA  
66  
2011 September  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
Figure 6171 / 2  
Ref. No.  
3M Part No.  
Description  
6171-28  
6171-29  
6171-30  
6171-31  
6171-32  
6171-33  
6171-34  
6171-35  
6171-36  
6171-37  
6171-38  
6171-39  
6171-40  
6171-41  
6171-42  
6171-43  
6171-44  
6171-45  
6171-46  
6171-47  
6171-48  
6171-49  
6171-50  
6171-51  
6171-52  
6171-53  
6171-54  
78-8017-9079-7  
78-8076-5418-7  
26-1003-7949-9  
78-8005-5741-1  
78-8010-7417-6  
78-8076-5419-5  
78-8046-8135-7  
78-8076-5420-3  
78-8076-5421-1  
78-8010-7169-3  
78-8070-1503-3  
78-8060-7878-4  
78-8076-4807-2  
78-8076-5422-9  
78-8070-1509-0  
26-1005-5316-8  
78-8070-1510-8  
78-8070-1511-6  
78-8005-5740-3  
78-8010-7157-8  
78-8070-1512-4  
78-8032-0375-7  
78-8076-4809-8  
78-8070-1506-6  
78-8076-5463-3  
78-8076-5424-5  
78-8076-5425-2  
Ring – Snap For 15 mm Shaft  
Support – Screw  
Screw – Soc Hd Hex Soc, M5 x 1  
Washer – Plain M5  
Nut – Hex M5  
Sprocket – 3/8 Inch Z=16  
Key – 5 x 5, 12mm  
Chain – 3/8 Inch, 133 Links  
Support – Tension Roller  
Screw – Hex Hd, M6 x 12  
Roller – Chain Tensioning  
Idler Screw  
Crank Assembly  
Crank  
Shaft – Crank  
Screw – Flat Hd Hex Dr, M5 x 16  
Washer – Nylon, 7 x 15 x 1  
Bushing  
Washer – Plain 4 mm  
Screw – Hex Hd, M4 x 10  
Knob – VTR-B-M12  
Screw – Hex Hd, M6 x 16  
Washer – Crank  
Cover – Screw  
Shaft  
Block  
Set Screw – M4 x 3  
67  
2011 September  
800a3-NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3 Adjustable Case Sealer  
26  
27  
29  
28  
27  
29  
28  
14  
25  
17  
30  
12  
17  
21  
13  
16  
23  
20  
4
22  
3
2
15  
18  
1
5
24  
15  
8
7
9
7
6
18  
19  
10  
11  
7
6
Figure 6172  
2011 September  
800a3-NA  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
800a3  
Figure 6172  
Ref. No.  
3M Part No.  
Description  
6172-1  
78-8113-6871-7  
26-1003-7957-2  
78-8100-1042-7  
78-8113-6810-5  
78-8113-6809-7  
26-1003-5842-8  
78-8017-9318-9  
26-1000-1347-8  
78-8070-1574-4  
78-8070-1575-1  
78-8076-5465-8  
78-8070-1576-9  
78-8070-1577-7  
78-8076-5466-6  
78-8076-5467-4  
78-8076-5468-2  
78-8076-5469-0  
26-1005-5316-8  
78-8070-1555-3  
78-8060-7758-8  
78-8054-8955-2  
26-1003-5820-4  
78-8005-5741-1  
78-8076-4517-7  
78-8113-6758-6  
78-8091-0538-6  
78-8076-4716-5  
78-8005-5740-3  
78-8010-7416-8  
78-8076-4500-3  
78-8100-1234-0  
Cross Bar – Lower, W/English Language Label  
Screw – Soc Hd Hex Hd, M6 x 16  
Washer – /15 x 6.35 x 2  
Frame – R/H, W/English Language Label  
Frame – L/H, W/English Language Label  
Screw – Hex Hd, M8 x 20  
Washer – Plain, 8 mm  
Nut – Hex, M8  
6172-2  
6172-3  
6172-4  
6172-5  
6172-6  
6172-7  
6172-8  
6172-9  
Slide – Front, Right  
6172-10  
6172-11  
6172-12  
6172-13  
6172-14  
6172-15  
6172-16  
6172-17  
6172-18  
6172-19  
6172-20  
6172-21  
6172-22  
6172-23  
6172-24  
6172-25  
6172-26  
6172-27  
6172-28  
6172-29  
6172-30  
6172-31  
Slide – Front, Left  
Spacer – Front Slide  
Slide – Rear, Right  
Slide – Rear, Left  
Spacer  
Spacer – Head Support  
Stud – Head Support  
Roller – /32X55  
Screw – Flat Hd Hex Dr, M5 x 16  
Block – Upper Head  
Fairlead – /20  
Clamp – Bracket  
Screw – Hex Hd, M5 x 12  
Washer – Flat, M5  
End Cap – /22 x 1  
Cover – Upper, W/English Language Label  
Screw – Hex Hd, M4 x 20  
Star Washer – M4  
Washer – Plain, 4 mm  
Nut – Hex, M4  
Stud – Mounting  
Bezel  
2011 September  
800a3-NA  
6967  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety  
Information  
Instructions and  
Parts List  
BEFORE INSTALLING  
OR OPERATING THIS  
EQUIPMENT  
3M-Matic™  
Read, understand, and  
follow all safety and  
operating instructions.  
AccuGlide™ 3  
Upper and  
Lower  
Spare Parts  
Taping Heads  
3 Inch  
It is recommended you  
immediately order the  
spare parts listed in the  
"Spare Parts/Service  
Information" section.  
These parts are expected  
to wear through normal  
use, and should be kept  
on hand to minimize  
production delays.  
Type 10800  
Serial No._____________________________________  
For reference, record taping head(s) serial number(s) here.  
AccuGlide™ is a Trademark of  
3M, St. Paul, MN 55144-1000  
Litho in U.S.A  
3M Industrial Adhesives and Tapes  
3M Center, Building 220-5E-06  
St. Paul, MN 55144-1000  
© 3M 2012 44-0009-2071-8 (E010712-NA)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts and Service Information  
To Our Customers:  
This is the 3M-Matic™/AccuGlide™/Scotch® equipment you ordered. It has been set up and tested in  
the factory with Scotch® tapes. If technical assistance or replacement parts are needed, call or fax the  
appropriate number listed below.  
Included with each machine is an Instructions and Parts List manual.  
Technical Assistance / Replacement Parts and Additional Manuals:  
Call the 3M-Matic™ Help line at 1-800 328-1390. Provide the customer support coordinator with the  
model/machine name, machine type, and serial number that are located on the identification plate  
(For example: Model 200a - Accuglide 3 - 3 inch - Type 10800 - Serial Number 13282).  
Identification Plate  
United States -  
3M Tape Dispenser Parts  
For Industrial use only  
4000563  
241 Venture Drive  
1-800-344-9883  
Amery, WI 54001-1325  
Fax: 1-715-268-8153  
Minimum billing on parts orders will be $25.00. Replacement part prices available on request.  
$10.00 restocking charge per invoice on returned parts  
Note : Outside the U.S., contact the local 3M subsidiary for  
parts ordering information.  
3M-Matic™, AccuGlide™ and Scotch™  
are Trademarks of  
3M Industrial Adhesives and Tapes  
3M Center, Building 220-5E-06  
3M St. Paul, MN 55144-1000  
St. Paul, MN 55144-1000  
i
3
Printed in U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts And Service Information  
To Our Customers:  
This is the 3M-Matic™/AccuGlide™/Scotch® equipment you ordered. It has been set up  
and tested in the factory with Scotch® tapes. If any problems occur when operating this equipment and  
you desire a service call or phone consultation, call, write, or fax the appropriate number listed below.  
Included with each machine is an Instructions and Parts List manual.  
SERVICE, REPLACEMENT PARTS, AND ADDITIONAL MANUALS  
AVAILABLE DIRECT FROM:  
Order parts by part number, part description, and quantity required. Also, when ordering parts  
or additional manuals, include model/machine name, machine type, and serial number that are  
located on the identification plate.  
3M-Matic™, AccuGlide™ and Scotch™  
are Trademarks of  
3M, St. Paul, MN 55144-1000  
Printed in U.S.A.  
3M Industrial Adhesives and Tapes  
3M Center, Building 220-5E-06  
St. Paul, MN 55144-1000  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instruction Manual  
AccuGlide™ 3  
Upper and Lower Taping Heads - 3 Inch  
Type 10800  
Table of Contents  
Page  
Equipment Warranty and Limited Remedy............................................................................................... i - ii  
Table of Contents...................................................................................................................................... iii  
Equipment Warranty and Limited Remedy............................................................................................... iv  
Intended Use............................................................................................................................................  
Taping Head Contents / How to Use Manual............................................................................................  
1
3
Important Safeguards............................................................................................................................... 4 - 5  
Specifications ........................................................................................................................................... 6 - 7  
Dimensional Drawing ....................................................................................................................  
7
Installation ................................................................................................................................................  
Receiving and Handling ................................................................................................................  
Installation Guidelines...................................................................................................................  
Tape Leg Length ...........................................................................................................................  
Tape Width Adjustment .................................................................................................................  
8
8
8
8
8
Operation.................................................................................................................................................. 9 - 11  
Tape Loading – Upper Taping Head.............................................................................................. 10  
Tape Loading – Lower Taping Head.............................................................................................. 10 - 11  
Maintenance............................................................................................................................................. 12 - 13  
Blade Replacement....................................................................................................................... 12  
Blade Guard.................................................................................................................................. 12  
Blade Oiler Pad............................................................................................................................. 12  
Cleaning........................................................................................................................................ 13  
Applying/Buffing Roller Replacement............................................................................................ 13  
Adjustments.............................................................................................................................................. 14 - 16  
Tape Latch Alignment.................................................................................................................... 14  
Tape Drum Friction Brake ............................................................................................................. 14  
Applying Mechanism Spring.......................................................................................................... 15  
One-Way Tension Roller ............................................................................................................... 15  
Tape Leg Length ........................................................................................................................... 16  
Leading Tape Leg Length Adjustment ............................................................................ 16  
Changing Tape Leg Length From 70 to 50 mm [2-3/4 to 2 Inch].................................... 16  
Troubleshooting........................................................................................................................................ 17 - 18  
Spare Parts/Service Information............................................................................................................... 19  
Recommended Spare Parts.......................................................................................................... 19  
Replacement Parts and Service.................................................................................................... 19  
Replacement Parts Illustrations and Parts List................................................................ Yellow Section 19 - 37  
2012 January  
AccuGlide 3 - 3" - NA  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warranty  
Equipment Warranty and Limited Remedy:  
Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL OTHER  
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND ANY IMPLIED WARRANTY ARISING  
OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE:  
3M sells its AccuGlide™ 3 Upper and Lower Taping Heads - 3 Inch, Type 10800 with the following warranty:  
1. The Taping Head blade, springs and rollers will be free from defects in material and manufacture for  
ninety (90) days after delivery.  
2. All other Taping Head parts will be free from defects in material and manufacture for three (3) years after  
delivery.  
If any part is defective within this warranty period, your exclusive remedy and 3M’s and seller’s sole obligation shall be,  
at 3M’s option, to repair or replace the part. 3M must receive actual notice of any alleged defect within a reasonable  
time after it is discovered, but in no event shall 3M have any obligation under this warranty unless it receives such  
notice within five (5) business days after the expiration of the warranty period. All notices required hereunder shall  
be given to 3M solely through the 3M-Matic™ Help line (800-328-1390). To be entitled to repair or replacement as  
provided under this warranty, the part must be returned as directed by 3M to its factory or other authorized service  
station designated by 3M. If 3M is unable to repair or replace the part within a reasonable time after receipt thereof,  
3M, at its option, will replace the equipment or refund the purchase price. 3M shall have no obligation to provide or  
pay for the labor required to remove any part or equipment or to install the repaired or replacement part or equip-  
ment. 3M shall have no obligation to repair or replace those parts failing due to normal wear, inadequate or improper  
maintenance, inadequatecleaning, non-lubrication, improperoperatingenvironment, improperutilities, operatorerror  
or misuse, alteration or modification, mishandling, lack of reasonable care, or due to any accidental cause.  
Limitation of Liability: Except where prohibited by law, 3M and seller will not be liable for any loss or damage arising  
from this 3M equipment, whether direct, indirect, special, incidental, or consequential, regardless of the legal theory  
asserted, including breach of warranty, breach of contract, negligence, or strict liability.  
Note: The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability may be changed only by  
a written agreement signed by authorized representatives of 3M and seller.  
Taping Head Contents  
AccuGlide™ 3 Upper and Lower Taping Heads - 3 Inch - consists of:  
Qty.  
Part Name  
1
1
1
1
Taping Head Assembly  
Tape Drum and Bracket Assembly  
Hardware and Spare Parts Kit  
Threading Tool  
AccuGlide™, Scotch™, and 3M-Matic™ are Trademarks of 3M, St. Paul, Minnesota 55144-1000  
2012 January  
AccuGlide 3 - 3" - NA  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Intended Use  
The intended use of the AccuGlide™ 3 Upper and  
Lower Taping Heads - 3 Inch- is to apply a "C" clip  
of Scotch® pressure-sensitive film box sealing tape  
to the top and/or bottom center seam of regular  
slotted containers.  
size and simplicity of the taping head also makes  
it suitable for mounting in box conveying systems  
other than 3M-Matic™ case sealers. This includes  
replacement of other types of taping, gluing or  
stapling heads in existing case sealing machines.  
The AccuGlide™ 3 Taping Heads have been  
designed and tested for use with Scotch® pressure-  
sensitive film box sealing tape.  
These taping heads are incorporated into most  
standard 3M-Matic™ case sealers. The compact  
AccuGlide™ 3 Upper Taping Head - 3 Inch, Type 10800  
1
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Taping Head Contents  
AccuGlide™ 3 Upper and Lower Taping Heads - 3 Inch - consists of:  
Qty.  
Part Name  
1
1
1
1
Taping Head Assembly  
Tape Drum and Bracket Assembly  
Hardware and Spare Parts Kit  
Threading Tool  
General Information  
This instruction manual covers safety aspects, handling and transport, storage, unpacking, preparation, installa-  
tion, operation, set-up and adjustments, technical and manufacturing specifications, maintenance, troubleshoot-  
ing, repair work and servicing, electric diagrams, warranty information, disposal (ELV), a glossary with a definition  
of symbols, plus a parts list 3M Industrial Adhesives and Tapes Division 3M Center, Bldg. 220-5E-06 St. Paul,  
MN 55144-1000 (USA) Edition January 2012/Copyright 3M 2012. All rights reserved The manufacturer reserves  
the right to change the product at any time without notice Publication © 3M 2012.  
How to use this Manual  
The manual is an important part of the machine; all information contained herein is intended to enable the equip-  
ment to be maintained in perfect condition and operated safely. Ensure that the manual is available to all opera-  
tors of this equipment and the manual is kept up to date with all subsequent amendments. Should the equipment  
be sold or disposed of, please ensure that the manual is passed on with the machine.  
Electrical and pneumatic diagrams are included in the manual. Equipment using PLC controls and/or electronic  
components will include relevant schematics or programs in the enclosure (or will be delivered separately as needed)  
Keep the manual in a clean and dry place near the machine. Do not remove, tear or rewrite parts of the manual  
for any reason. Use the manual without damaging it. However, if the manual has been lost or damaged, ask your  
after sale service for a new copy (if it is possible, please have the manual name, part number, and revision infor-  
mation and/or model/machine name, machine type, and serial number) that are located on the identification plate  
(For example: Model - 200a / Accuglide 3 - 3" - Type 10800 - Serial Number 13282).  
Note:  
All the important warning notes related to the operation of the machine are identified by the symbol:  
Updating the Manual  
Modifications to the machine are subject to manufacturer's internal procedures. The user may receive pages or parts  
ofthemanualwhichcontainamendmentmadeafteritsfirstpublication. Theusermustusethemtoupdatethismanual.  
3
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safeguards  
This safety alert symbol identifies  
CAUTION  
important safety messages in this  
manual. READ AND UNDERSTAND  
THEM BEFORE INSTALLING OR  
OPERATING THIS EQUIPMENT.  
•
To reduce the risk associated with  
muscle strain:  
− Use proper body mechanics when  
removing or installing taping heads that  
are moderately heavy or may be considered  
awkward to lift  
Explanation of Signal Word Consequences  
•
Toreducetheriskassociatedwithimpact  
hazards:  
Indicates a potentially hazardous  
situation, which, if not avoided,  
could result in death or serious  
injury and/or property damage.  
WARNING:  
− Place the taping head on a smooth level  
surface when maintaining or servicing this  
equipment.  
Indicates a potentially hazardous  
situation, which, if not avoided,  
may result in minor or moderate  
injury and/or property damage.  
CAUTION:  
WARNING  
•
Pour réduire le risque associé aux dangers  
mécaniques et électriques:  
−
Lisez, comprenez, et suivez toutes les  
consignes de sécurité d’utilisation avant d’utiliser  
ou entretenir la colleuse de carton.  
Permettre uniquement au personnel  
correctement formé et qualifié d’utiliser et  
entretenir cet équipement.  
−
•
Pour réduire le risque associé aux  
pincements, à l’enchevêtrement et tension  
électrique dangereuse:  
− Couper l’alimentation électrique et débrancher  
avant d’effectuer tout réglage, toute  
maintenance ou entretien courant sur la  
machine ou les applicateurs de ruban.  
•
Pour réduire le risque associé aux dangers  
de pincements et enchevêtrement:  
−
Ne pas laisser la machine en fonctionnement  
sans surveillance.  
−
−
Arrêtez la machine quand elle n’est pas utilisée.  
N’essayez jamais de travailler sur quelque  
partie que ce soit de la machine, de charger le  
ruban, ou d’enlever des boîtes bloqués dans la  
machine pendant que la machine fonctionne.  
•
Pour réduire le risque associé à la tension  
électrique dangereuse:  
−
Placez le cordage électrique loin de la  
circulation de pieds et de véhicules.  
4
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safeguards (continued)  
Important – In the event the following safety labels are damaged or destroyed, they must be replaced to  
ensure operator safety. See "Replacement Parts Illustrations and Parts Lists" for label part numbers.  
Upper Taping Head Label 78-8137-3317-3  
Lower Taping Head Label 78-8137-3316-5  
78-8070-1335-0  
Figure 1-1 Replacement Labels/3M Part Numbers  
5
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
1. Tape:  
For use with Scotch® pressure-sensitive film box sealing tapes.  
2. Tape Width:  
48mm [2 inches] minimum to 72mm [3 inches] maximum.  
3. Tape Roll Diameter:  
Up to 405mm [16 inches] maximum on a 76.2mm [3 inch] diameter core.  
(Accommodates all system roll lengths of Scotch® film tapes.)  
4. Tape Application Leg Length - Standard:  
70mm ± 6mm [2-3/4 inches ±1/4 inch]  
Tape Application Leg Length - Optional:  
50mm ± 6mm [2 inches ± 1/4 inch] (See "Adjustments – Tape Leg Length.")  
5. Box Size Capacities:  
For use with center seam regular slotted containers.  
Minimum  
Maximum  
Length –  
150mm [6 inches]  
Unlimited  
Limited by  
Case Sealer  
Height – 120mm [4-3/4 inches] (most “3M-Matic” Case Sealers)  
90mm [3-1/2 inches] (with optional 2 inch leg length)  
Width – 150mm [6 inches]  
When upper and lower taping heads are used on “3M-Matic” case sealers, refer to the respective instruction  
manual specifications for box weight and size capacities.  
6. Operating Rate:  
Conveyor speeds up to 0.5 m/s [100 feet per minute].  
7. Operating Conditions:  
Use in dry, relatively clean environments at 5° to 40° C [40° to 105° F] with clean dry boxes.  
Important – Taping heads should not be washed down or subjected to conditions causing moisture  
condensation on components.  
8. Taping Head Dimensions:  
Length  
Height  
Width  
–
–
–
–
442 mm [17 3/8 inches]  
648 mm [25 1/2 inches] (with tape drum)  
130 mm [5-1/8 inches] (without mounting spacers)  
Packaged: 8.2 kg [18 lbs.] Unpackaged: 7.3 kg [16 lbs.]  
Weight  
6
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications (continued)  
396 mm  
[15-19/32 in.]  
13 mm  
[1/2 in.]  
130mm (5 1/8)  
278 mm  
[10-15/16 in.]  
58 mm  
[2 9/32 in.]  
405 mm  
18 mm [11/16 in.]  
18 mm [11/16 in.]  
445 mm  
[17-1/2 in.]  
405 mm  
7
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
WARNING  
• To reduce the risk associated with sharp blade hazards:  
− Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades  
are extremely sharp  
Receiving And Handling  
3. Figure 2-1 illustrates the typical mounting  
relationship for opposing taping head  
After the taping head assembly has been  
unpackaged, examine the unit for damage that  
might have occurred during transit. If damage is  
evident, file a damage claim immediately with the  
transportation company and also notify your 3M  
Representative.  
assemblies to allow taping of box heights down  
to 90mm [3-1/2 inches]. To tape box heights  
down to 70mm [2-3/4 inches], the taping heads  
must be completely staggered so only one tape  
seal is being applied at one time.  
Note – AccuGlide™ 3 Upper Taping Head is  
supplied with a buffing arm guard. Adjustments to  
this guard may be required to install the taping head  
into some older design 3M-Matic™ case sealers.  
Installation Guidelines  
The taping head assembly can be used in converting  
existing or in custom made machinery.  
It can be mounted for top taping or bottom taping.  
Refer to "Box Size Capacities," as well as Figure  
2-1 in the Specifications section, for the following  
points in making such installations:  
4. Mounting studs are provided with the taping  
head, but special installations may require  
alternate means for mounting.  
5. Box hold-down or guide skis should be provided  
and the taping head mounted so that the side  
plates are 6mm [1/4 inch] maximum away from  
the ski surface on which the box rides.  
CAUTION  
•
To reduce the risk associated with  
muscle strain:  
− Use proper body mechanics when  
removing or installing taping heads that  
are moderately heavy or may be  
considered awkward to lift  
Tape Leg Length  
Taping heads are factory set to apply standard  
70mm [2-3/4 inch] tape legs. The heads can be  
converted to apply 50mm [2 inch] tape legs if desired  
but both upper and lower heads must be set to ap-  
ply the same tape leg length. See "Adjustments –  
Changing Tape Leg Length From 70 to 50mm  
[2-3/4 to 2 Inches]."  
Important – Always conduct a hazard review to  
determine appropriate guarding requirements  
when the installation is in an application other  
than 3M-Matic (TM) equipment  
Also, the conveyor speed at which the product  
moves through the taping heads, affects the leading  
and trailing tape leg length. See "Adjustments sec-  
tion – Leading Tape Leg Length Adjustment."  
1. The box conveying system must positively  
propel the box in a continuous motion, not  
exceeding 0.50 m/s [100 feet per minute],  
past the taping head assembly since the box  
motion actuates the taping mechanism.  
Tape Width Adjustment  
2. If a pusher or cleated conveyor is being used,  
steps should be taken in the conveyor design to  
prevent the pusher from contacting the applying  
or buffing roller arms resulting in damage to the  
taping head.  
Taping heads are factory set to apply 72mm [3 inch]  
wide tape. If it is necessary to align the tape or to  
apply narrower tapes, refer to "Adjustments – Tape  
Web Alignment" for set-up procedure.  
8
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
Tape Drum  
Tape Supply Roll  
Tape Adhesive Side  
One-Way  
Tension Roller  
Applying  
Mechanism  
Spring  
Tension Wrap Roller  
Knurled Roller  
Buffing Arm  
Cover  
Wrap Roller  
Buffing  
Roller  
Threading Needle  
Applying Roller  
Tape Cut-Off Knife  
Orange Knife Guard  
Figure 3-1 Taping Head Components/Threading Diagram - Upper Head (Left Side) View)  
Orange Knife Guard  
Tape Cut-Off Knife  
Applying Roller  
Threading Needle  
Wrap Roller  
Buffing  
Roller  
Buffing Arm  
Knurled Roller  
Cover  
Tension Wrap Roller  
Applying  
Mechanism  
Spring  
One-Way  
Tension Roller  
Tape Adhesive Side  
Tape Supply Roll  
Tape Drum  
Figure 3-2 Taping Head Components/Threading Diagram - Lower Head (Left Side) View)  
9
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation (continued)  
WARNING  
•
To reduce the risk associated with shear, pinch, and entanglement hazards:  
−
Turn air and electrical supplies off on associated equipment before performing any adjustments,  
maintenance, or servicing the machine or taping heads  
−
Never attempt to work on the taping heads or load tape when the box drive system is running  
•
To reduce the risk associated with sharp blade hazards:  
−
Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are  
extremely sharp  
5. Pull the threading needle down until the tape  
travels between the apply plate and the ears of  
the apply arm (Position 4) until it extends past  
the applying roller. When properly threaded the  
adhesive side of the tape should be facing the  
knurled rollers at position 2 and also position 3.  
It is recommended that the detailed instructions and  
sketches in this manual be referred to the first few  
times the taping head is loaded/threaded until the  
operator becomes thoroughly familiar with the tape  
loading operation.  
Note – Remove tape roll before removing  
taping head from machine to minimize weight.  
6. Cut away any excess tape.  
Important – Do not cut against the apply roller -  
CAUTION  
roller damage could occur.  
Tape Loading – Lower Taping Head  
•
To reduce the risk associated with  
muscle strain:  
1. Remove the lower taping head from the  
conveyor bed or associated equipment and  
place it a convenient working position.  
−
Use proper body mechanics when  
removing or installing taping heads that  
are moderately heavy or may be  
considered awkward to lift  
2. The lower taping head is loaded and threaded  
in the same manner as the upper head. Follow  
the upper taping head tape loading/threading  
procedure.  
•
To reduce the risk associated with  
impact hazards:  
Figure 3-3 Insert threading needle through rollers in  
direction indicated by arrows.  
−
Place the taping head on a smooth level  
surface when maintaining or servicing this  
equipment  
One-Way  
Tension  
Roller  
Tape Loading – Upper Taping Head  
1. Place the upper taping head in a convenient  
working position.  
Tension  
Wrap  
Roller  
1
2
2. Refer to Figures 3-3 to 3-5 and tape threading  
label. Position the tape supply roll so the adhe-  
sive side of tape is facing the front of the taping  
head as it is pulled from the supply roll.  
Knurled  
Roller  
Wrap  
Roller  
3
3. Attach the threading needle to the end of the  
roll. Guide the threading needle around the wrap  
roller (Position 1) then back around the one-way  
tension roller (Position 2).  
Applying  
Roller  
4. Continue pulling the threading needle down and  
guide it between the two rollers on the apply arm  
(Position 3).  
4
Figure 3-3 – Tape Loading/Threading  
10  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation (continued)  
Figure 3-4  
Place tape roll on tape drum to dispense tape with  
adhesive side forward. Seat tape roll fully against  
back flange of drum. Adhere tape lead end to  
threading needle as shown.  
WARNING  
• To reduce the risk associated with  
sharp blade hazards:  
Figure 3-4 – Tape Loading/Threading  
− Keep hands and fingers away from tape  
cutoff blades under orange blade guards.  
The blades are extremely sharp  
Manually turn tape roll to create slack tape while  
pulling threading needle through tape applying  
mechanism until needle is through and tape is in  
alignment with applying roller.  
Excess tape can be cut with a scissors at applying  
roller.  
Figure 3-5 – Tape Loading/Threading  
11  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
WARNING  
•
To reduce the risk associated with shear, pinch, and entanglement hazards:  
−
Turn air and electrical supplies off on associated equipment before performing any adjustments,  
maintenance, or servicing the taping heads  
−
•
Never attempt to work on the taping head or load tape while the box drive system is running  
To reduce the risk associated with sharp blade hazards:  
−
Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are  
extremely sharp  
The AccuGlide™ 3 Taping Head - 3 Inch has  
been designed for long, trouble free service. The  
taping head will perform best when it receives  
routine maintenance and cleaning. Taping head  
components that fail or wear excessively should be  
promptly repaired or replaced to prevent damage to  
other portions of the head or to the product.  
3. Bottom the blade slots against the screws.  
(This will position the blade at the correct angle.)  
Tighten the blade screws to secure the blade.  
Note – Check the blade position to insure  
proper clearance between blade and guard  
by slowly pivoting the blade guard back.  
Blade Replacement, Upper and Lower Taping  
Heads – Figure 4-1  
Blade Guard  
The blade guard covers the blade whenever a box  
is not being taped. Periodically check to be sure the  
blade guard is functioning properly and returning to  
cover the blade. Replace any defective parts.  
WARNING  
• To reduce the risk associated with  
sharp blade hazards:  
Blade Oiler Pad  
− Keep hands and fingers away from tape  
cutoff blades under orange blade guards.  
The blades are extremely sharp  
WARNING  
• To reduce the risk associated with  
sharp blade hazards:  
1. Loosen, but do not remove, the blade screws  
(A). Remove and discard old blade.  
− Keep hands and fingers away from tape  
cutoff blades under orange blade guards.  
The blades are extremely sharp  
2. Mount the new blade (B) with the beveled side  
away from the blade holder.  
To reduce adhesive build-up, the taping heads are  
equipped with a factory pre-lubricated felt oiler pad  
that provides a film of oil on the cutting edge of tto  
reduce adhesive build-up. Apply SAE #30 non-  
detergent oil as needed. Saturate felt oiler pad.oil.  
Should tape adhesive build-up occur on blade,  
carefully wipe clean with an oily cloth.  
Knife  
Holder  
Knife  
Guard  
Figure 4-1 – Blade Replacement  
12  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance (continued)  
WARNING  
•
To reduce the risk associated with shear, pinch, and entanglement hazards:  
−
Turn air and electrical supplies off on associated equipment before performing any adjustments,  
maintenance, or servicing the taping heads  
−
•
Never attempt to work on the taping head or load tape while the box drive system is running  
To reduce the risk associated with sharp blade hazards:  
−
Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are  
extremely sharp  
Cleaning  
Applying/Buffing Roller Replacement  
Regular slotted containers produce a great deal  
of dust and paper chips when conveyed through  
taping heads. If this dust is allowed to build-up  
on the heads, it can cause wear on the moving  
parts. Excessive dirt build-up should be wiped  
off with a damp cloth. Cleaning should be done  
once per month, depending on the number and  
type of boxes used. If the boxes used are dirty, or  
if the environment in which the heads operate is  
dusty, cleaning on a more frequent basis may be  
necessary.  
Replacing roller requires removal of shaft and  
mounting screws. With no area on the shaft to grip,  
the shaft often turns when attempting to remove the  
second screw.  
To ease removal of second screw, a 5mm hex  
socket has been provided at the bottom of the  
threads in both ends of the shaft. Insert a 5mm  
hex key wrench into this socket after removing one  
screw to hold the shaft for removal of the second  
screw. See Figure 4-2.  
Note – Never attempt to remove dirt from taping  
heads by blowing it out with compressed air. This  
can cause the dirt to be blown inside the  
components onto sliding surfaces. Dirt in these  
areas can cause serious equipment damage.  
Never wash down or subject taping heads to  
conditions causing moisture condensation on  
components. Serious equipment damage could  
result.  
Hex Socket  
Section View of  
Roller/Shaft  
5mm Hex  
Key Wrench  
Figure 4-2 – Roller Shaft Section View  
13  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjustments  
WARNING  
• To reduce the risk associated with shear,  
pinch, and entanglement hazards:  
− Turn air and electrical supplies off on  
associated equipment before performing any  
adjustments, maintenance, or servicing the  
machine or taping heads  
− Never attempt to work on the taping head  
or load tape while the box drive system is  
running  
Figure 5-1 – Tape Latch Alignment  
Tape Latch Alignment – Figure 5-1  
The Latching tape drum assembly is pre-set to  
accommodate 72mm [3 inch] wide tape. The tape  
drum assembly is adjustable to provide alignment of  
narrower tapes.  
To move the latch to a position that corresponds to a  
new tape core width (Figure 5-1):  
1. Remove screw from the latch.  
2. Move to the latch to the position that corresponds  
to the tape core width.  
3. Replace screw in the new latch location.  
25mm Hex  
Wrench  
5mm Hex  
Wrench  
To adjust or center the tape width on the centerline  
of the taping head, and therefore box center seam,  
(Figure 5-2):  
1. Loosen the locking hex nut behind tape drum  
bracket on tape drum shaft. Use an adjustable  
wrench or 25mm open end wrench.  
Shaft  
Figure 5-2 – Tape Web Alignment  
Note – To set up 72mm tape drum for 48mm tape,  
disassemble tape drum from bracket and install  
lock nut between tape drum and bracket as shown  
in inset, Figure 5-3.  
Adjustment Nut,  
Tape Drum Brake  
2. Turn tape drum shaft in or out to center the tape  
web (use 5mm hex wrench).  
3. Tighten locking hex nut to secure the adjustment.  
No other components require adjustment for tape web  
alignment.  
Tape Drum Friction Brake – Figure 5-3  
The tape drum friction brake on each taping head is  
pre-set for normal operation to prevent tape roll over  
travel. Should tension adjustment be required, turn  
the self-locking nut on the shaft to vary compression  
of the spring. Turn the nut clockwise to increase the  
braking force, and counterclockwise to decrease the  
braking force. Adjust brake to minimum tension to  
prevent excessive tape roll over travel.  
Note – Excess braking force will cause poor tape  
application and may lead to tape tabbing on the  
trailing tape leg.  
Figure 5-3 – Tape Drum Friction Brake  
14  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjustments (continued)  
WARNING  
A
• To reduce the risk associated with shear,  
pinch, and entanglement hazards:  
− Turn air and electrical supplies off on  
associated equipment before performing any  
adjustments, maintenance, or servicing the  
machine or taping heads  
− Never attempt to work on the taping head  
or load tape while the box drive system is  
running  
Applying Mechanism Spring  
To obtain access to the spring, remove the taping  
head cover (four mounting screws). Replace cover  
when finished.  
The applying mechanism spring, shown in  
Figures 5-4A and 5-4B, controls applying and  
buffing roller pressure on the box and returns  
the mechanism to the reset position. The spring  
pressure is pre-set, as shown in Figure 5-4A for  
normal operation, but is adjustable.  
B
Figure 5-4 – Applying Mechanism Spring  
If a tape gap appears on the trailing surface of the  
box increase spring pressure. If the front of the box  
is being crushed by the applying roller decrease  
spring pressure.  
Removing the spring end loop from the spring holder  
and placing loop in other holes provided, as shown  
in Figure 5-4B, will adjust the spring pressure.  
One-Way Tension Roller  
Figure 5-5  
0.5 - 0.9kg  
[1 - 2 lbs.]  
The one-way tension roller is factory set. When  
replacing this assembly, the roller must have a force  
of approximately 0.5 kg to 0.9 kg [1 to 2 lbs.] when  
turning.  
To Adjust Tension:  
1. Wrap a cord or small strap (non-adhesive) 4-6  
turns around the tension roller.  
2. Attach a spring scale to the end of the cord or  
strap.  
3. Turn the adjusting nut with the socket wrench  
provided, until a force of approximately 0.5 kg to  
0.9 kg [1 to 2 lbs.] is required to turn the roller by  
pulling on the spring scale.  
Adjusting Nut  
Figure 5-5 – One-Way Tension Roller  
15  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjustments (continued)  
WARNING  
• To reduce the risk associated with shear,  
pinch, and entanglement hazards:  
One-Way  
Tension  
Roller  
− Turn air and electrical supplies off on  
associated equipment before performing any  
adjustments, maintenance, or servicing the  
machine or taping heads  
− Never attempt to work on the taping head  
or load tape while the box drive system is  
running  
Tape Leg Length  
WARNING  
• To reduce the risk associated with sharp  
blade hazards:  
− Keep hands and fingers away from tape  
cutoff knives under orange blade guards.  
The blades are extremely sharp  
Tape Leg  
50 or 70mm ± 6mm  
[2 or 2-3/4in. ± 1/4in.  
Leading Tape Leg Length Adjustment – Figure 5-6  
Figure 5-6 – Leading Tape Leg Length  
The one-way tension roller position is adjustable to  
control the leading tape leg length.  
Moving this roller farther away from the box top or  
bottom surface will decrease the leading leg length.  
Moving it closer to the box top or bottom surface will  
increase the leading leg length.  
One-Way  
Tension Roller  
Assembly  
Position A  
Position A-A  
Changing Tape leg Length from 70 to 50mm [2-3/4 to  
2 inches] – Figure 5-7  
Slot C-C  
Slot C  
Note – When changing tape leg length, both upper  
and lower heads must be adjusted to apply the  
same leg lengths.  
1. Remove and retain two hex head screws and  
remove the brush from normal position “A” on side  
frame.  
2. Remount and secure brush in position “A-A” on  
side frame forward of normal location using original  
fasteners.  
3. Remove cut-off bracket extensions from position "B".  
4. Remount cut-off bracket extensions in forward  
position “B-B”.  
5. Remove and retain the one-way tension roller  
assembly from slot “C” in frame.  
6. Remount tension roller assembly near top of slot  
“C-C” in frame using original fasteners.  
7. Adjust tension roller according to "Leading Tape Leg  
Length Adjustment" above.  
Cut-Off  
Bracket  
Extension  
Position B  
Brush  
Position B-B  
Figure 5-7 – Changing Tape Leg Length  
16  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Troubleshooting Guide  
Problem  
Cause  
Correction  
The tape is threaded incorrectly  
The tape must go around the wrap  
roller before going around the  
one-way tension roller  
The tape leg on the front of the  
case is too long  
The tape tension is too low  
The knurled roller drags  
Adjust the one-way tension roller  
Check for adhesive build-up  
between the knurled roller and its  
shaft. Clean and lubricate shaft.  
Remove all lubricant from roller  
surfaces.  
Tape tracks to one side or drags  
on the support tabs of applying  
frame  
Adjust the tape web alignments  
The one-way tension roller is not  
correctly positioned  
Position the roller in its mounting  
slot so that the tape extends just  
beyond the center line of the  
applying roller  
Taping head is not set up properly  
Check leg length adjustments  
Replace the blade  
The blade is dull and/or has  
broken teeth  
The blade does not cut tape or the  
tape end is jagged or shredded  
Tape tension is insufficient  
Increase tape tension by adjusting  
the one-way tension roller  
Adhesive has built up on the blade  
Clean and adjust the blade  
The blade is not positioned  
properly  
Make sure the blade is bottomed  
out against the mounting bolts  
The blade is dry  
Lubricate the blade oiler pad on  
the blade guard  
The blade is in backwards  
Mount the blade so that the  
beveled edge is away from the  
entrance of the head  
One or both cutter springs are  
missing or stretched  
Replace the defective spring(s)  
Tension roller surface is not fully  
contacting the taping head frame  
Make sure one-way bearing is  
below the surface of the tension  
roller. If not, press bearing further  
into roller or replace roller.  
(continued)  
17  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting (continued)  
Troubleshooting Guide  
Problem  
Cause  
Correction  
There is excess tension on the  
tape drum assembly and/or the  
one-way tension roller assembly  
Adjust the one-way tension roller  
and/or the tape drum assembly  
Tape is tabbing on the trailing leg  
on the back of the box  
Rollers in the tape path do not  
rotate freely  
Clean adhesive deposits from  
the surface, ends, and shafts of  
the rollers. Then lubricate roller  
shafts. Remove all lubricant from  
roller surfaces.  
The blade is not cutting tape  
properly  
Refer to tape cutting problems  
Rethread the tape  
The tape is threaded incorrectly  
Applying mechanism spring has  
too little tension  
Move spring hook to next tighter  
hole  
The tape is incorrectly threaded  
Rethread the tape  
The tape end does not stay in  
application position in front of the  
applying roller  
Flanged knurled roller overruns on  
return of applying mechanism to  
its rest position  
Adjust tension roller position in  
mounting slot to lengthen tape leg  
Applying roller overruns on return  
of applying mechanism to its rest  
position  
There should be a slight drag  
when rotating the applying roller.  
If not, check friction springs and/  
or friction pins and replace if  
necessary  
The one-way tension roller is not  
correctly positioned  
Position roller in it mounting slot  
so that tape end extends beyond  
center line of applying roller  
The one-way tension roller is  
defective  
Replace the one-way tension  
roller  
Tape drum not centered  
Reposition tape drum  
Adjust centering guides  
Check box specifications  
Tape not centered on box seam  
Centering guides not centered  
Box flaps not of equal length  
18  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Spare Parts/Service Information  
Recommended Spare Parts  
Listed are a set of spare parts that will periodically require replacement due to normal wear. These parts should  
be ordered to keep the taping heads in production:  
AccuGlide™ 3 Upper Taping Head - 3 Inch  
Qty.  
Part Number  
Description  
4
1
1
2
1
78-8076-4500-3  
78-8137-3311-6  
78-8028-7899-7  
78-8052-6602-6  
78-8076-4726-4  
Stud – Mounting  
Spring – Upper Extension  
Knife – 89mm/3.5 Inch  
Spring – Cutter  
Tool – Tape Threading  
AccuGlide™ 3 Lower Taping Head - 3 Inch  
Qty.  
Part Number  
Description  
1
2
4
1
1
78-8028-7899-7  
78-8052-6602-6  
78-8076-4500-3  
78-8137-3312-4  
78-8076-4726-4  
Knife – 89mm/3.5 Inch  
Spring – Cutter  
Stud – Mounting  
Spring – Lower Extension  
Tool – Tape Threading  
In addition to the above set of spare parts supplied with the taping head, it is suggested that the following spare  
parts be maintained which will require replacement under normal wear of the taping head.  
Qty.  
Part Number  
Description  
1
1
1
78-8057-6181-0  
78-8057-6180-2  
78-8113-7030-9  
Roller – Applying  
Roller – Buffing  
Spring – Torsion  
Replacement Parts and Service  
Refer to the first page of this instruction manual “Replacement Parts and Service Information."  
19  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts Illustrations and Parts Lists  
AccuGlide™ 3 Upper Taping Head - 3 Inch, Type 10800  
AccuGlide™ 3 Lower Taping Head - 3 Inch, Type 10800  
1.  
Refer to the Taping Head Assemblies Figure to find all the parts illustrations identified by figure numbers.  
2.  
Refer to the figure or figures to determine the individual parts required and the parts reference number.  
3 .  
The replacement parts list, that follows each illustration, includes the part number and part description  
for the parts in that illustration.  
Note – The complete description has been included for standard fasteners and some commercially  
available components. This has been done to allow obtaining these standard parts locally, should the  
customer elect to do so.  
4.  
Refer to the first page of this instruction manual "Replacement Parts and Service Information" for  
replacement parts ordering information.  
Important – Not all the parts listed are normally stocked items. Some parts or assemblies  
shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts  
to confirm item availability.  
20  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
Tape Head -  
™
AccuGlide 3 - 3 inch  
Figure 10402  
Figure 10932 (Upper)  
Figure 10931 (Lower)  
Figure 10930  
Figure 10929  
Figure 10926 (Upper)  
Figure 10927 (Lower)  
Figure 10928  
21  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
Figure 10932 – Upper Head  
22  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
Figure 10932 – Upper Head  
Ref. No.  
3M Part No.  
Description  
10932-1  
78-8137-3294-4  
78-8137-3295-1  
78-8068-4143-9  
78-8068-4144-7  
78-8060-7818-0  
78-8010-7416-8  
78-8076-4735-5  
78-8137-3309-0  
78-8060-7939-4  
78-8060-7936-0  
78-8054-8796-0  
78-8054-8798-6  
26-1003-5829-5  
78-8100-1009-6  
78-8054-8797-8  
26-1004-5510-9  
78-8052-6567-1  
78-8017-9077-1  
78-8054-8799-4  
26-1000-1613-3  
78-8076-4500-3  
78-8076-5242-1  
78-8060-8179-6  
78-8076-5477-3  
78-8137-3310-8  
78-8060-8087-1  
78-8005-5741-1  
78-8133-9615-3  
78-8133-9605-4  
78-8060-7937-8  
78-8060-7938-6  
78-8076-4716-5  
Frame – Tape Mount Upper Assembly  
Frame – Front Upper Assembly  
Guide – #1  
10932-2  
10932-3  
10932-4  
Guide – #2  
10932-5  
Screw – Hex Hd, M4 x 12  
Nut – Hex Jam, M4  
10932-6  
10932-7  
Spacer – Spring  
10932-8  
Shaft - Pivot 115mm  
Spacer – 10 x 115 W/Slots  
Brush Assembly  
10932-9  
10932-10  
10932-11  
10932-12  
10932-13  
10932-15  
10932-16  
10932-17  
10932-18  
10932-19  
10932-20  
10932-21  
10932-22  
10932-23  
10932-24  
10932-25  
10932-26  
10932-27  
10932-28  
10932-29  
10932-30  
10932-31  
10932-32  
10924-33  
Shaft – Tension Roller  
Shaft – Wrap Roller  
Screw – Hex Hd, M6 x 12  
Washer – Special  
Roller – Top Tension  
Washer – Plain, M10  
Spring – Compression  
Nut – Self Locking, M10 x 1  
Roller – Wrap  
Ring – Retaining, Tru-Arc #1-420-0120-100  
Stud – Mounting (not shown)  
Stop – Cut-Off Frame  
Screw - Flat Head Hex, M6 x 20  
Washer – Special, 6.5 x 20 x 4  
Guard – Head  
Screw – M5 x 10  
Washer – Flat, M5  
Bumper  
Label – Threading, English Language  
Spacer 6.5 / 14 x 12.5  
Screw - Low Profile M6 x 25  
Star Washer 4mm  
23  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
16  
16  
15  
14  
15  
Figure 10929 – Upper and Lower Heads  
24  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
Figure 10929 – Upper and Lower Heads  
Ref. No.  
3M Part No.  
Description  
10929-1  
10929-2  
10929-3  
10929-4  
10929-5  
10929-6  
10929-7  
10929-8  
10929-9  
10929-10  
10929-11  
10929-12  
10929-13  
10929-14  
10929-15  
10929-16  
78-8133-9520-5  
78-8133-9521-3  
78-8070-1292-3  
78-8076-4736-3  
78-8076-4737-1  
78-8076-4738-9  
78-8054-8806-7  
78-8017-9082-1  
78-8017-9106-8  
78-8054-8801-8  
78-8017-9074-8  
26-1004-5510-9  
78-8052-6567-1  
78-8137-1392-8  
26-1003-5829-5  
78-8094-6151-6  
Arm – Applying, R/H  
Arm – Applying, L/H  
Plate – Back-Up  
Shaft Roller  
Roller Assembly – Knurled  
Roller – Wrap  
Spacer  
Bearing – Special, 30 mm  
Screw – Bearing Shoulder  
Shaft – 10 x 85, W/Hexagon  
Washer – Nylon, 15mm  
Washer – Friction  
Spring – Compression  
Assembly– Applying Roller  
Screw – Hex Hd, M6 x 12  
Washer - Flat, 6.5 ID x 15 OD x 0.5 Thk  
25  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
1
2
5
7
7
8
7
9
6
7
7
4
3
7
Figure 10926 – Upper Head  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
Figure 10926 – Upper Head  
Ref. No.  
3M Part No.  
Description  
10926-1  
10926-2  
10926-3  
10926-4  
10926-5  
10926-6  
10926-7  
10926-8  
10926-9  
78-8137-3300-9  
78-8137-3301-7  
78-8091-0799-4  
78-8137-1397-7  
78-8076-4739-7  
78-8052-6580-4  
26-1003-5829-5  
78-8137-3311-6  
78-8070-1244-4  
Buffing Arm – Sub Assembly  
Buffing Arm – Sub Assembly  
Shaft – 10 x 85, W/Hexagon  
Roller – Buffing Assembly  
Spacer – Spring  
Spacer  
Screw – Hex Hd, M6 x 12  
Spring – Upper (100 fpm)  
Holder – Spring  
27  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
6
6
1
3
7
8
7
5
9
4
9
5
4
Figure 10930 – Upper and Lower Heads  
28  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
Figure 10930 – Upper and Lower Heads  
Ref. No.  
3M Part No.  
Description  
10930-1  
10930-3  
10930-4  
10930-5  
10930-6  
10930-7  
10930-8  
10930-9  
78-8137-3302-5  
78-8137-3314-0  
78-8017-9082-1  
78-8017-9106-8  
26-1003-5829-5  
78-8137-3305-8  
78-8137-3313-2  
78-8094-6151-6  
Link – R/H Assembly  
Shaft – Pivot, Buffing  
Bearing – Special 30 mm  
Screw – Bearing Shoulder  
Screw – Hex Hd, M6 x 12  
Spacer – Applying Pivot  
Shaft – Pivot, Applying  
Washer - Flat, 6.5 ID x 15 OD x 0.5 Thk  
29  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
17  
18  
5
7
15  
3
4
7
2
16  
14  
10  
13  
15  
11  
16  
13  
9
12  
14  
10  
9
11  
8
Figure 10928 – Upper and Lower Heads  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
Figure 10928 – 3" Upper and Lower Heads  
Ref. No.  
3M Part No.  
Description  
10928-1  
10928-2  
10928-3  
10928-4  
10928-5  
10928-7  
10928-8  
10928-9  
10928-10  
10928-11  
10928-12  
10928-13  
10928-14  
10928-15  
10928-16  
10928-17  
10928-18  
10928-19  
78-8070-1283-2  
78-8028-7899-7  
26-1002-5817-2  
78-8076-4741-3  
78-8054-8813-3  
26-1005-4758-2  
78-8060-7941-0  
78-8052-6600-0  
78-8070-1269-1  
26-1005-4757-4  
78-8052-6602-6  
78-8017-9132-4  
26-1003-5828-7  
78-8070-1216-2  
26-1008-6574-5  
78-8113-7060-6  
78-8113-7030-9  
78-8070-1335-0  
Frame – Cut-Off  
Knife – 89 mm/3.5 Inch  
Screw – Hex Hd, M5 x 8  
Knife Guard Assembly – W/English Language Label  
Shaft – Knife Guard  
Screw – Flat Hd, Soc Dr, M4 x 10  
Pin – Spring Holder W/Slots  
Spacer  
Bumper  
Screw – Flat Hd, Soc Dr, M5 x 20  
Spring – Cutter  
Pivot – Cutter Lever  
Screw – Spec, Hex Hd, M6 x 10  
Slide – Extension  
Screw – Flat Hd, Phil Dr, M4 x 10  
Bushing – 83.7 mm Long  
Spring – Torsion  
Label – Warning, English  
31  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
13  
14  
3
1
13  
12  
13  
13  
13  
4
14  
4
7
2
16  
5
8
9
17  
15  
10  
11  
6
7
7
Figure 10402 – Upper and Lower Heads  
32  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
Figure 10402 – 3" Latch Upper and Lower Heads  
Ref. No.  
3M Part No.  
Description  
10402-1  
10402-2  
10402-3  
10402-4  
10402-5  
10402-6  
10402-7  
10402-8  
10402-9  
10402-10  
10402-11  
10402-12  
10402-13  
10402-14  
10402-15  
10402-16  
10402-17  
78-8070-1395-4  
78-8060-8462-6  
78-8017-9169-6  
78-8098-8829-6  
78-8098-8828-8  
78-8098-8830-4  
26-1002-5753-9  
78-8060-8172-1  
78-8052-6271-0  
78-8100-1048-4  
78-8017-9077-1  
78-8100-1050-0  
26-1003-5829-5  
78-8133-9641-9  
26-1004-5510-9  
78-8098-8816-3  
78-8052-6651-3  
Bracket – Bushing Assembly  
Shaft – Tape Drum, 3 Inch Head  
Nut – M18 x 1  
Tape Drum Sub Assembly – 3 Inch Wide  
Tape Drum  
Leaf Spring  
Screw – Self Tapping  
Washer – Friction  
Washer – Tape Drum  
Spring – Core Holder  
Nut – Self Locking, M10 x 1  
Spacer – Bracket  
Screw – Hex Hd, M6 x 12  
Tape Drum Assembly – 3 Inch Head  
Washer – Plain, M10  
Latch – Tape Drum  
Washer - Nylon  
33  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
23  
10  
23  
20  
7
5
9
21  
32  
13  
31  
13  
13  
31  
12  
19  
17  
18  
17  
16  
27  
15  
29  
11  
24  
25  
29  
8
1
2
4
28  
27  
3
26  
Figure 10931 – Lower Head  
34  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
Figure 10931 – Lower Head  
Ref. No.  
3M Part No.  
Description  
10931-1  
78-8137-3296-9  
78-8137-3297-7  
78-8068-4144-7  
78-8068-4143-9  
83-0002-7336-3  
78-8010-7416-8  
78-8076-4735-5  
78-8137-3309-0  
78-8060-7939-4  
78-8060-7936-0  
78-8054-8796-0  
78-8054-8798-6  
26-1003-5829-5  
78-8100-1009-6  
78-8054-8817-4  
26-1004-5510-9  
78-8052-6567-1  
78-8017-9077-1  
78-8054-8799-4  
26-1000-1613-3  
78-8076-4500-3  
78-8076-5242-1  
78-8060-8179-6  
78-8076-5477-3  
78-8137-3310-8  
78-8060-8087-1  
78-8005-5741-1  
78-8133-9615-3  
78-8133-9606-2  
78-8060-7937-8  
78-8060-7938-6  
78-8076-4716-5  
Frame – Tape Mount Lower Assembly  
Frame – Front Lower Assembly  
Guide – #2  
10931-2  
10931-3  
10931-4  
Guide – #1  
10931-5  
Screw – Hex Hd, M4 x 14  
Nut – Hex, M4  
10931-6  
10931-7  
Spacer – Spring  
10931-8  
Spacer – 10 x 10 x 115 mm  
Spacer – 10 x 115, W/Slots  
Brush Assembly  
10931-9  
10931-10  
10931-11  
10931-12  
10931-13  
10931-15  
10931-16  
10931-17  
10931-18  
10931-19  
10931-20  
10931-21  
10931-22  
10931-23  
10931-24  
10931-25  
10931-26  
10931-27  
10931-28  
10931-29  
10931-30  
10931-31  
10931-32  
10924-33  
Shaft – Tension Roller  
Shaft – Wrap Roller  
Screw – Hex Hd, M6 x 12  
Washer – Special  
Roller – Tension Bottom  
Washer – Plain, M10  
Spring – Compression  
Nut – Self Locking, M10 x 1  
Roller – Wrap  
Ring – Retaining, Tru-Arc #1-420-0120-100  
Stud – Mounting (not shown)  
Stop – Cut-Off Frame  
Screw – Flat Head Hex, M6 x 20  
Washer – Special /6.5 x 20 x 4  
Guard – Head  
Screw – M5 x 10  
Washer – Flat, M5  
Bumper  
Label – Threading, English Language  
Spacer 6.5 / 14 x 12.5  
Screw - Low Profile M6 x 25  
Star Washer 4mm  
35  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
7
3
4
6
7
7
9
7
8
7
5
7
2
1
Figure 10927 – Lower Head  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AccuGlide™ 3 - 3"  
Figure 10927 – Lower Head  
Ref. No.  
3M Part No.  
Description  
10927-1  
10927-2  
10927-3  
10927-4  
10927-5  
10927-6  
10927-7  
10927-8  
10927-9  
78-8137-3300-9  
78-8137-3301-7  
78-8091-0799-4  
78-8137-1397-7  
78-8076-4739-7  
78-8052-6580-4  
26-1003-5829-5  
78-8137-3312-4  
78-8070-1244-4  
Buffing Arm – Sub Assembly  
Buffing Arm – Sub Assembly  
Shaft – 10 x 85, W/Hexagon  
Roller – Buffing  
Spacer – Spring  
Spacer  
Screw – Hex Hd, M6 x 12  
Spring – Lower (100 fpm)  
Holder – Spring  
37  
2012 January  
AccuGlide 3 - 3" - NA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Acer Computer Monitor ETDG5HP006 User Manual
Aga Ranges Range F107411 01 User Manual
Agilent Technologies Network Card J6800A User Manual
Akai Clock Radio AR321S User Manual
AKG Acoustics Headphones 3052H00040 User Manual
Allied Telesis Switch PN 613 User Manual
Amana Range AER5522VAW User Manual
AMD Computer Hardware 790GX User Manual
Axis Communications Printer 5600 User Manual
BC Speakers Speaker 18P WB 46 User Manual