3Com Switch 3CDSG8 User Manual

Installation Guide  
®
OfficeConnect  
Managed Gigabit Switch (3CDSG8)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ABOUT YOUR SWITCH  
OfficeConnect Managed Gigabit Switch - Rear  
OfficeConnect Managed Gigabit Switch - Front  
3CDSG8  
Port Status  
Duplex  
On  
=
=
Full  
Off  
Half  
Power  
Status  
Module  
Active  
1
2
3
4
5
6
7
8/SFP  
1
2
3
4
5
6
7
8
Green  
=
1000M, Yellow  
=
10/100M, Flash  
=
Activity  
OfficeConnect Managed Gigabit Switch  
CONSOLE  
POWER  
SFP  
1
2
3
4
5
6
7
8
9
6
Power Adapter Socket  
Only use the power adapter that is supplied with the Switch.  
SFP Port  
1
Power LED  
Green  
Indicates that the Switch is receiving power from the power adapter. If the LED is off  
there may be a problem with the adapter.  
7
1000BaseLX (3CSFP92) and 1000BaseSX (3CSFP91) transceivers are supported. Use  
this interface to allow your Switch to connect across distances greater than 100m or  
where electrical isolation is required. Appropriate multimode fiber cables will also be  
required (not supplied).  
Refer to Problem Solving.  
2
Status LED  
Green/Yellow  
This LED is used to indicate the status of the system. When this LED is green and not  
flashing, the system is operating normally. When the switch is booting up and during  
firmware upgrades the LED will flash green. If the system has failed the Power On Self  
Test (POST) the LED will illuminate yellow.  
SFP transceivers are hot-insertable and hot-swappable. You can remove them  
from and inset them without having to power down the switch.  
Use of non-3Com SFPs is not recommended. 3Com cannot guarantee  
operation of the switch if non-3Com SFPs are used.  
3
Module Active LED  
Green  
8
Console Interface  
This LED is used to indicate that an SFP module is inserted and is active.  
Use the supplied DB-9 to RJ45 serial cable to connect to the switchs command line  
interface. Default Settings are 38,400 baud, 8 data bits, no parity, no flow control.  
4
Eight/ Port Status LEDs  
Green (1000 Mbps link) / Yellow (10 or 100Mbps link)  
9
10BASE-T/100BASE-TX/1000BASE-T Ports  
If the LED is on, the link between the port and the next piece of equipment is OK. If  
the LED is flashing, the link is OK and data is being transmitted or received. If the LED  
is off, nothing is connected or the connected device is turned off, or there is a problem  
with the connection (refer to the Problem Solving section).  
Use suitable TP cable with RJ-45 connectors. You can connect your Switch to a work-  
station, or any other piece of equipment that has 10BASE-T/100BASE-TX/1000BASE-T  
connectivity. Each port is capable of autosensing for 10 Mbps, 100 Mbps or 1000 Mbps  
operation. All ports have an automatic MDI/MDIX feature, which means either  
straight-through or crossover cable can be used to connect to any port.  
5
Duplex LEDs  
Green (10/100/1000 Mbps, full duplex) /  
Off (10/100 Mbps, half duplex)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
When positioning your Switch, ensure:  
• It is out of direct sunlight and away from sources of heat.  
WARNING: RJ-45 ports.  
• Cabling is away from power lines, fluorescent lighting fixtures, and sources of elec-  
trical noise such as radios, transmitters and broadband amplifiers.  
• Water or moisture cannot enter the case of the unit.  
• Air flow around the unit and through the vents in the side of the case is not restricted.  
3Com recommends you provide a minimum of 25 mm (1 in.) clearance.  
These are shielded RJ-45 data sockets. They cannot be used as standard traditional  
telephone sockets, or to connect the unit to a traditional PBX or public telephone  
network. Only connect RJ-45 data connectors, network telephony systems, or net-  
work telephones to these sockets.  
Either shielded or unshielded data cables with shielded or unshielded jacks can be  
connected to these data sockets.  
Using the Rubber Feet  
Use the four self-adhesive rubber feet to prevent your Switch from moving around on  
your desk, or when stacking with flat top OfficeConnect units. Only stick the feet to  
the marked areas at each corner on the underside of your Switch.  
VORSICHT: RJ-45-Portes.  
Diese Portes sind geschützte Datensteckdosen. Sie dürfen weder wie normale  
traditionelle Telefonsteckdosen noch für die Verbindung der Einheit mit einem  
traditionellenm privatenm oder öffentlichenm Telefonnetzwerk gebraucht werden.  
Nur RJ-45- Datenansclußhlüsse, Telefonnetzsysteme oder Netztelefone an diese  
Steckdosen anschließen. Entweder geschützte oder ungeschützte Buchsen dürfen  
an diese Datensteckdosen angeschlossen werden.  
Wall Mounting  
There are two slots on the underside of the Switch that can be used for wall mount-  
ing. The Switch must be mounted with the LEDs facing upwards. When wall mount-  
ing the unit, ensure it is within reach of the power Outlet When wall mounting the  
unit, ensure that the rubber feet are not fixed.  
AVERTISSEMENT : Prises RJ-45 blindées.  
Mounting Instructions for Cement Walls  
Ces prises ne peuvent servir comme prises telephone standard et ne permettent pas  
la connexion de l'appareil à un système PBX ni à un réseau téléphonique public.  
N'y branchez que des prises RJ-45 mâles adaptées, ou des systèmes de réseaux  
téléphoniques. Il est possible d'y brancher des câbles blindés ou non comportant  
des prises de type Jack (blindées ou non).  
1 Make two holes 150 mm (5.9 in.) apart and insert two nylon or similar screw  
anchors that are suitable for the wall construction.  
2 Fix two suitable screws into the anchors, leaving their heads 3 mm (0.12 in.) clear of  
the wall surface. The screws should be at least 30 mm (1.2 in.) long,  
3 Remove any connections in the Switch and locate it over the screw heads. When in  
line, gently push the Switch on to the wall and move it downwards to secure.  
1. POSTIONING YOUR SWITCH  
Mounting Instructions for Wood Walls  
Safety Information  
1 Make two holes 150 mm (5.9 in.) apart.  
2 Fix two suitable screws directly into the wall, leaving their heads 3 mm (0.12 in.)  
clear of the wall surface. The screws should be at least 20 mm (0.75 in.) long,  
3 Remove any connections in the Switch and locate it over the screw heads. When in  
line, gently push the Switch on to the wall and move it downwards to secure.  
WARNING: Please read the ‘Important Safety Information’ section in the  
Support and Safety Information sheet before you start.  
VORSICHT: Bitte lesen Sie den Abschnitt ‘Wichtige Sicherheitsinformationen’  
sorgfältig durch, bevor Sie das Gerät einschalten.  
CAUTION: When making connections, be careful not to push the Switch up  
and off the wall.  
AVERTISSEMENT: Veuillez lire attentivement la section "Consignes  
importantes de sécurité" avant de mettre en route.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. SETTING UP FOR MANAGEMENT  
Your Switch can operate in its default state, that is, you can install it and it will work  
straight away (plug-and-play). However, to make full use of the features offered by the  
Switch, and to change and monitor the way it works, you have to access the manage-  
ment software that resides on the Switch. This is known as managing the Switch.  
Managing the Switch can help you to improve the efficiency of the Switch and there-  
fore the overall performance of your network.  
IP Configuration  
When the switch is powered up and connected to a network, the switch will obtain an  
address from the DHCP server. If there is no DHCP server available, the switch will use  
a default IP address of 169.254.xx.yy, where xx and yy are the last two bytes of the  
MAC address. This default IP address is also printed on the label attached to the  
underside of your switch.  
Before you can manage your switch, you will need to determine its IP address to allow  
a web browser to connect to it. You can do this either by connecting your workstation  
to the console interface using the cable supplied, or using the 3Com Switch Detect  
application that can be found on the CD that was supplied with the Switch.  
Please follow the instructions below to determine and/or configure the IP address of  
your switch.  
Using the Console Interface  
1. Connect the DB-9 to RJ-45 serial cable between your workstation (to its COM port)  
and the Switch. Take care not to connect it to a data port on the Switch.  
2. Using a terminal emulator program, for example HyperTerminal, connect to the  
appropriate COM port on the workstation and ensure the following parameters are  
set: 38400 baud, 8 data bits, no parity, 1 stop bit and no flow control.  
3. If the Switch is not already powered up, power it up now and wait for the boot up  
sequence to complete.  
4. When the boot up sequence is completed, you will be presented with a login  
prompt. The default username is admin. No password is required.  
5. To show the IP address the switch is using, enter IP status and press Return. The  
switch will display the IP address the switch is using. This address can now be used  
in your preferred web browser to connect to the Switch User Interface. Use the  
same username to log in.  
6. If you want to manually assign an IP address, enter the following commands:  
IP dhcp disableand press Return  
IP Setup <IP Address> <ipmask> <gateway>and press Return  
For example: IP Setup 192.168.1.2 255.255.255.0 192.168.1.1  
You can now direct the web browser at the 192.168.1.2 address.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the 3Com Switch Detect Application  
3 CONNECTING WORKSTATIONS  
1. On the computer that is connected to your Switch (either directly or on a network  
that is on the same subnet), insert the CD-ROM into its CD drive. If you have  
autorunenabled, you will be presented with a menu showing the contents of the  
CD-ROM.  
2. Select the 3Com Detect Application link to install the utility. Follow the onscreen  
instructions.  
3. If the auto-run program does not start, you should browse to your CD-ROM drive,  
go to the /switch detectdirectory and double click on setup.exe. Follow the  
prompts that will take you through the installation process.  
Twisted Pair (TP) Cables  
Cables can be shielded (screened) or unshielded. Cables must be Category 5 or above.  
3Com recommends Category 5E or 6 cable for Gigabit connections. The maximum  
length you can use is 100 m (328 ft).  
Twisted Pair (TP) cable is very easy to use. To connect a TP cable, simply slot the con-  
nector into the relevant RJ-45 Port. When a connector is fully in, its latch locks into  
place. To disconnect the cable, push the connectors latch in and remove it.  
When one end of a TP cable is connected to the Switch and the other end is connect-  
ed to the network interface card of a workstation or other device, the Switch will  
automatically detect whether a straight-through or crossover cable is being used and  
will compensate if required. The units will then autonegotiate to determine the fastest  
possible link speed between them. This may take a few seconds and the outcome will  
be reflected in the LEDs on the front of the Switch.  
4. Once installed, the 3Com Switch Detect Application can be accessed from the  
Windows Start/Programs list.  
5. When the 3Com Detect application starts, you will be see the Welcome Screen (see  
below).  
6. If the computer has multiple network adapters, select the adapter that connects the  
computer to the network or Switch, click "Next."  
7. You will then be offered the choice of searching the same subnet that your PC is on  
for a connected switch (default), or specifying an IP range. Note that specifying a  
large range may take some time for the search to complete.  
8. Once your Switch or Switches have been located, you will be presented with a list.  
Select the switch to which you want to connect and click on "Open." Your default  
Web browser will open and connect to the home page of the Switch.  
If the equipment connected to the Switch does not support autonegotiation or it  
has been disabled, it must be configured to operate in half duplex mode.  
Expanding Your Network  
You can increase the number of workstations and other devices that can connect to  
your network by adding OfficeConnect gateways and switches. The Switch has auto-  
matic MDI/MDIX functionality. Simply plug in the cable and the Switch will automati-  
cally detect which wiring practice has been followed and will compensate accordingly.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
For reference, the part number for the power adapter supplied for your region is:  
4 PROBLEM SOLVING  
3C number  
Region  
The Switch has been designed to aid you when detecting and solving possible prob-  
lems with your network. These problems are rarely serious; the cause is usually a dis-  
connected or damaged cable, or incorrect configuration. If this section does not solve  
your problem, contact your supplier for information on what to do next.  
3C12VUS  
3C12VUK  
3C12VME  
3C12VAA  
3C12VSA  
3C12VKR  
3C12VRA  
US and Canada  
UK  
Europe and Middle East  
Australasia  
South Africa  
Korea  
Perform these actions first:  
• Ensure all network equipment is powered on.  
• Power each piece of network equipment off, wait about five seconds and then  
power each one on.  
Argentina  
CAUTION: Do not power the Switch off and then immediately on. Wait about  
five seconds between power cycles.  
Power LED lit but Status LED illuminated yellow.  
This indicates that the switch is receiving power, but for some reason the switch is not  
operational. This is most likely due to a problem with the operational software in the  
unit not loading correctly.  
Check the following symptoms and solutions:  
Power LED not lit.  
This is probably because the switch does not have power. Check the following:  
Refer to the diagnostic messages displayed on the command line interface (CLI) to  
help identify the problem. If the software is corrupted, you can re-load the software  
from the CLI. Please follow the instructions found in the User Guide for this Switch  
which can be found on the on the CD which is supplied with your Switch or which  
can be downloaded from www.3Com.com.  
• Make sure the power lead from the power adapter is properly connected and the  
cord is not damaged.  
• Ensure the power adapter is correctly fitted into the power outlet socket and that  
the socket switch is turned on if applicable.  
• Ensure you are using only the 3Com power adapter supplied with the switch.  
If a software reload does not resolve the issue, contact 3Com Technical Support and  
ask for assistance  
If there is still no power, contact 3Com Technical Support and ask for assistance.  
Only use the power adapter supplied with the Switch or a replacement  
OfficeConnect power adapter. Do not use any other power adapter.  
Port Status LED not lit for a port that has a TP cable connected.  
After connection, it may take several seconds for the Port Status LEDs to illuminate.  
The Port Status LED should turn Green or Yellow, for each port that is connected.  
If the Port Status LED is not lit after several seconds, ensure that the connected device  
is powered on, that the TP cable is not damaged and that it is correctly inserted at  
both ends.  
You may find that a TP cable works when connected to the Switch, but does not work  
if disconnected from the Switch and connected to another device. This may be  
because the other device does not have the automatic MDI/MDIX feature.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Support and  
Safety Information  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Information  
Consignes de sécurité importantes  
WARNING: Warnings contain directions you must follow for your personal  
Avertissement: Ces avertissements sont à respecter pour votre sécurité.  
safety. Follow all directions carefully.  
Lisez-les attentivement.  
You must read the following safety information before carrying out any installation  
or removal of the unit, or any maintenance procedures.  
Vous devez impérativement lire les consignes de sécurité suivantes avant de procéder  
à l’installation ou à la désinstallation du matériel, ou à toute activité d’entretien.  
WARNING: Exceptional care must be taken during installation and removal of  
the unit.  
Avertissement: Linstallation et la désinstallation du matériel nécessite une  
vigilance exceptionnelle.  
WARNING: To ensure compliance with international safety standards this prod-  
uct must only be used with a power supply that is approved in the country of use.  
Avertissement: Pour être conforme aux normes de sécurité internationales, ce  
produit doit être utilisé exclusivement avec une alimentation aux normes du pays  
d’utilisation.  
The power supply output must be +12VDC, 1A minimum and the polarity of the  
power supply output connector must comply with the marking on the unit.  
La sortie de l’alimentation doit être de 12 V continus, 1A minimum, et les polarités  
du connecteur de sortie doivent coïncider avec les indications figurant sur l’appareil.  
WARNING: Disconnect the power adapter before moving the unit.  
WARNING: This unit operates under SELV (Safety Extra Low Voltage) conditions  
according to IEC 60950-1. The conditions are only maintained if the equipment to  
which it is connected also operates under SELV conditions.  
Avertissement: Coupez systématiquement l’adaptateur secteur avant de  
déplacer l’appareil.  
Avertissement: Cet appareil fonctionne à très basse tension de sécurité (SELV,  
Safety Extra Low Voltage) conformément à la norme IEC 60950-1. Pour ce faire, le  
matériel auquel il est connecté doit également fonctionner sous SELV.  
WARNING: RJ-45 Ports. These are shielded RJ-45 data sockets. They cannot be  
used as standard traditional telephone sockets, or to connect the unit to a tradi-  
tional PBX or public telephone network. Only connect RJ-45 data connectors, net-  
work telephony systems, or network telephones to these sockets.  
Avertissement: Ports RJ 45. Il s’agit de connecteurs de communication de  
données blindés RJ 45. Il n’est pas possible de les utiliser comme prises téléphoniques  
classiques ni de connecter l’appareil à un standard téléphonique classique ou à un  
réseau téléphonique public. Seuls des connecteurs de réseau de données RJ 45, des  
systèmes de téléphonie en réseau ou des téléphones réseau peuvent y être  
branchés.  
Either shielded or unshielded data cables with shielded or unshielded jacks can be  
connected to these data sockets.  
Vous pouvez y brancher des câbles pour réseau de données blindés ou non pourvus  
de prises jack blindées ou non aux extrémités.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 Wichtige Sicherheitsinformationen 
 
Importanti informazioni di sicurezza ╙  
Warnung: Warnhinweise enthalten Anweisungen, die Ihrer persönlichen  
Avvertenza: Queste avvertenze precisano le direttive da seguire per la propria  
Sicherheit dienen. Befolgen Sie all diese Anweisungen mit größter Sorgfalt.  
sicurezza personale. Conformarsi con la massima attenzione a quanto precisato.  
Lesen Sie unbedingt die folgenden Sicherheitsinformationen, bevor Sie eine  
Installation oder Entfernung des Gerätes vornehmen bzw. Wartungen/  
Instandhaltungen durchführen.  
Leggere con attenzione le informazioni relative alla sicurezza prima di procedere  
all’installazione o alla rimozione dell’unità o a qualsiasi intervento di manutenzione.  
Avvertenza: E’ necessario prestare la massima attenzione durante l’instal-  
Warnung: Bei der Installation und Entfernung des Gerätes ist mit äußerster  
lazione e la rimozione dell’unità.  
Sorgfalt vorzugehen.  
Avvertenza: Per garantire la piena conformità con gli standard di sicurezza  
internazionali, il prodotto deve essere utilizzato con un’alimentazione approvata  
nello specifico paese di utilizzo.  
Warnung: Um die Übereinstimmung mit den internationalen  
Sicherheitsstandards zu gewährleisten, darf dieses Produkt nur mit einer  
Stromversorgung betrieben werden, die den Bestimmungen des jeweiligen Landes  
entspricht.  
Luscita dell’alimentazione deve essere +12V DC, 1A minimo e la polarità del  
connettore dell’uscita dell’alimentazione dovrà conformarsi con la marcatura  
riportata sull’unità.  
Die Netzsteckdose muss +12VDC, 1A minimal haben und die Polarität des  
Netzanschlusses muss der Kennzeichnung auf dem Gerät entsprechen.  
Avvertenza: Scollegare l’adattatore di alimentazione prima di spostare l’unità.  
Warnung: Nehmen Sie vor dem Transport des Gerätes den Netzadapter ab.  
Avvertenza: Quest’unità funziona in condizioni SELV (Safety Extra Low  
Voltage) conformemente a IEC 60950-1. Tali condizioni potranno essere man-  
tenute solo se l’apparecchiatura a cui è collega funziona similmente in condizioni  
SELV.  
Warnung: Dieses Gerät arbeitet gemäß IEC 60950-1 mit Schutzkleinspannung  
(SELV = Safety Extra Low Voltage). Dieser Schutz bleibt nur erhalten, wenn die  
angeschlossene Anlage ebenfalls über SELV verfügt.  
Warnung: RJ-45 Anschluss. Dies sind abgeschirmte RJ-45-Datenbuchsen. Sie  
können nicht als herkömmliche Standardtelefonbuchsen verwendet werden und  
verbinden das Gerät nicht mit einer herkömmlichen Telefonanlage oder einem  
öffentlichen Telefonnetz. Schließen Sie an diese Buchsen nur RJ-45-  
Avvertenza: Porte RJ-45. Si tratta di prese dati schermate RJ-45. Non potranno  
essere utilizzate come prese telefoniche tradizionali o per collegare l’unità ad una  
normale rete PBS o telefonica pubblica. Collegare a queste prese solo connettori  
RJ-45, sistemi di telefonia in rete o telefoni in rete.  
Datenanschlüsse, Netzwerktelefonieanlagen oder Netzwerktelefone an.  
A queste prese dati potranno essere collegati cavi dati schermati o meno con jack  
schermati o meno.  
An diese Datenbuchsen können abgeschirmte oder nicht abgeschirmte Stecker  
angeschlossen werden.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Información de seguridad importante ╗  
Istotne Bezpieczeństwo Informacja  
Advertencia: Las advertencias contienen instrucciones que debe seguir para su  
seguridad personal. Siga todas las instrucciones atentamente.  
Warning: Ostrzeżenia zawierają wskazówki, których należy przestrzegać w  
celu zagwarantowania bezpieczeństwa osobistego. Do tych zaleceń należy  
stosować się dokładnie.  
Debe leer la siguiente información de seguridad antes de llevar a cabo la instalación  
o extracción de la unidad, o cualquier procedimiento de mantenimiento.  
Przed przystąpieniem do instalacji, usuwania urządzenia lub jakichkolwiek  
czynności konserwacyjnych należy zapoznać się z instrukcjami bezpieczeństwa.  
Advertencia: Se debe extremar el cuidado durante la instalación y extracción  
de la unidad.  
Warning: Podczas montażu lub demontażu urządzenia należy pracować z  
wyjątkową uwagą.  
Advertencia: Para asegurar la conformidad con los estándares de seguridad  
internacionales, este producto sólo se puede usar con una fuente de alimentación  
aprobada en el país de uso.  
Warning: Aby zapewnić zgodność z międzynarodowymi standardami  
bezpieczeństwa, produkt należy wyłącznie używać w połączeniu z zasilaczem  
zatwierdzonym w danym kraju.  
La salida de la fuente de alimentación debe ser de +12V CC, de 1A mínimo y la  
polaridad del conector de salida de alimentación debe cumplir con la marca en la  
unidad.  
Gniazdo zasilania musi mieć parametry +12VDC, 1A minimum, a biegunowość  
złącza wyjściowego musi być zgodna z oznaczeniami na urządzeniu.  
Advertencia: Desconecte el adaptador de alimentación antes de desplazar la  
Warning: Przed przeniesieniem urządzenia należy odłączyć zasilacz.  
unidad.  
Warning: Urządzenie działa w warunkach SELV (obwód bezpiecznego niskiego  
napięcia) zgodnie z normą IEC 60950-1. Warunki te są jednak zagwarantowane  
wyłącznie wtedy, gdy sprzęt, do którego podłączone jest urządzenie, również  
Advertencia: Esta unidad opera bajo condiciones SELV (muy bajo voltaje de  
seguridad) de acuerdo con la norma IEC 60950-1. Las condiciones sólo se  
mantienen si el equipo al que está conectado también opera bajo condiciones SELV. pracuje w obwodzie SELV.  
Advertencia: Puertos RJ-45 Son enchufes de datos RJ-45 blindados. No se  
pueden usar en los tradicionales enchufes telefónicos estándar, o para conectar la  
unidad a una red PBX tradicional o red telefónica pública. Conecte únicamente a  
estos enchufes los conectores de datos RJ-45, sistemas de telefonías de red o  
teléfonos de red.  
Warning: Porty RJ-45. Są to ekranowane gniazda RJ-45 do danych. Nie są  
przeznaczone do użycia jako standardowe gniazda telefoniczne lub do  
podłączenia urządzenia do PBX lub publicznej sieci telefonicznej. Do tych gniazd  
wolno podłączać wyłącznie wtyki RJ-45 danych, systemów telefonii sieciowej  
lub telefonów sieciowych.  
A estos enchufes de datos se pueden conectar cables blindados o no blindados con Do tych gniazd można podłączać kable danych ekranowane lub nieekranowane z  
tomas hembra blindadas o no blindadas.  
ekranowanymi lub nieekranowanymi wtykami.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ENVIRONMENTAL STATEMENTS  
REGULATORY NOTICES  
It is the policy of 3Com Corporation to be environmentally-friendly in all operations. To  
uphold our policy, we are committed to:  
FCC Statement  
This equipment has been tested and found to comply with the limits for a Class A  
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference when the equipment is  
operated in a commercial environment. This equipment generates, uses and can radi-  
ate radio frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications. Operation of  
this equipment in a residential area is likely to cause harmful interference to radio com-  
munications, in which case the user will be required to correct the interface at their  
own expense.  
• Establishing environmental performance standards that comply with national legisla-  
tion and regulations.  
• Conserving energy, materials and natural resources in all operations.  
• Reducing the waste generated by all operations.  
• Ensuring that all waste conforms to recognized environmental standards.  
• Maximizing the recyclable and reusable content of all products.  
• Ensuring that all products can be recycled, reused and disposed of safely.  
• Ensuring that all products are labelled according to recognized environmental  
standards.  
• Improving our environmental record on a continual basis.  
Information to the User  
End Of Life Statement  
If this equipment does cause interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is encouraged to try to cor-  
rect the interference by one or more of the following measures:  
3Com processes allow for the recovery, reclamation and safe disposal of all end-of-life  
electronic components.  
• Reorient or relocate the receiving antenna  
Regulated Materials Statement  
• Relocate the equipment away from the receiver  
• Move the equipment away from the receiver  
• Plug the equipment into a different outlet so that equipment and receiver are on  
different branch circuits.  
3Com products do not contain any hazardous or ozone-depleting material.  
Environmental Statement about the Documentation  
The documentation for this product is printed on paper that comes from sustainable,  
managed forests; it is fully biodegradable and recyclable, and is completely chlorine-  
free. The varnish is environmentally-friendly, and the inks are vegetable-based with a  
low heavy-metal content.  
How to identify and resolve radio-TV interference problems  
This booklet is available from the U.S. Government Printing Office, Washington,  
DC 20402, Stock No. 004-000-00345-4  
Environmental Statement about the Product Packaging  
In order to meet FCC emissions limits, this equipment must be used only with cables  
that comply with IEEE 802.3.  
The packaging for this product is fully recyclable. It has a recycled (post consumer)  
waste content of at least 40% by weight, and no heavy-metal content.  
For further details please refer to  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ICES Statement  
OBTAINING SUPPORT FOR YOUR PRODUCT  
This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.  
3Com offers product registration, case management, and repair services through  
eSupport.3com. You must have a user name and password to access these services,  
which are described in this appendix.  
CE Statements (Europe)  
EU Representative:  
Register Your Product to Gain Service Benefits  
3Com Europe Limited  
Peoplebuilding 2, Peoplebuilding Estate  
Maylands Avenue  
To take advantage of warranty and other service benefits, you must first register your  
product at: http://eSupport.3com.com/. 3Com eSupport services are based on  
accounts that are created or that you are authorized to access.  
Hemel Hempstead, Hertfordshire  
HP2 4NW  
United Kingdom  
Solve Problems Online  
3Com offers the following support tool:  
• 3Com Knowledgebase — Helps you to troubleshoot 3Com products. This query-  
based interactive tool is located at: http://knowledgebase.3com.com. It con-  
tains thousands of technical solutions written by 3Com support engineers.  
This product complies with the European Low Voltage Directive 73/23/EEC as amended  
by European Directive 93/68/EEC and EMC Directive 2004/108/EC.  
Warning: This is a class A product. In a domestic environment this product may cause  
radio interference in which case the user may be required to take adequate measures.  
Purchase Extended Warranty and Professional Services  
To enhance response times or extend your warranty benefits, you can purchase value-  
added services such as 24x7 telephone technical support, software upgrades, onsite  
assistance, or advanced hardware replacement.  
A copy of the signed Declaration of Conformity can be downloaded from the Product  
Support web page at http://www.3com.com/  
Experienced engineers are available to manage your installation with minimal disrup-  
tion to your network. Expert assessment and implementation services are offered to fill  
resource gaps and ensure the success of your networking projects. For more informa-  
tion on 3Com Extended Warranty and Professional Services, see:  
China RoHS  
Contact your authorized 3Com reseller or 3Com for additional product and support  
information. See the table of access numbers later in this appendix.  
Access Software Downloads  
You are entitled to bug fix / maintenance releases for the version of software that you  
initially purchased with your 3Com product. To obtain access to this software, you  
need to register your product and then use the Serial Number as your login. Restricted  
Software is available at: http://eSupport.3com.com/  
To obtain software releases that follow the software version that you originally pur-  
chased, 3Com recommends that you buy an Express or Guardian contract, a Software  
Upgrades contract, or an equivalent support contract from 3Com or your reseller.  
Support contracts that include software upgrades cover feature enhancements, incre-  
mental functionality, and bug fixes, but they do not include software that is released  
by 3Com as a separately ordered product. Separately orderable software releases and  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
licenses are listed in the 3Com Price List and are available for purchase from your  
3Com reseller.  
Country  
Telephone Number  
00801 444 318  
001 800 441 2152  
Taiwan  
Thailand  
Contact Us  
3Com offers telephone, internet, and e-mail access to technical support and repair  
services. To access these services for your region, use the appropriate telephone num-  
ber, URL, or e-mail address from the table in the next section.  
Pakistan Call the U.S. direct by dialing 00 800 01001, then dialing 800 763 6780  
Sri Lanka Call the U.S. direct by dialing 02 430 430, then dialing 800 763 6780  
Vietnam Call the U.S. direct by dialing 1 201 0288, then dialing 800 763 6780  
Telephone Technical Support and Repair  
You can also obtain non-urgent support in this region at this email address  
To obtain telephone support as part of your warranty and other service benefits, you  
must first register your product at: http://eSupport.3com.com/  
Or request a return material authorization number (RMA) by FAX using this number:  
+61 2 9937 5048, or send an email at this email address:  
When you contact 3Com for assistance, please have the following information ready:  
• Product model name, part number, and serial number  
• A list of system hardware and software, including revision level  
• Diagnostic error messages  
Country  
Telephone Number  
• Details about recent configuration changes, if applicable  
Europe, Middle East, and Africa — Telephone Technical Support and Repair  
From anywhere in these regions not listed below, call: +44 1442 435529  
From the following countries, call the appropriate number:  
To send a product directly to 3Com for repair, you must first obtain a return materials  
authorization number (RMA). Products sent to 3Com without authorization numbers  
clearly marked on the outside of the package will be returned to the sender  
unopened, at the senders expense. If your product is registered and under warranty,  
you can obtain an RMA number online at http://eSupport.3com.com/. First-time  
users must apply for a user name and password.  
Austria  
0800 297 468  
0800 71429  
800 17309  
0800 113153  
0800 917959  
0800 182 1502  
06800 12813  
1 800 553 117  
180 945 3794  
800 879489  
Belgium  
Denmark  
Finland  
Telephone numbers are correct at the time of publication. Find a current directory of  
3Com resources by region at: http://csoweb4.3com.com/contactus/  
France  
Germany  
Hungary  
Ireland  
Israel  
Italy  
Country  
Telephone Number  
Asia, Pacific Rim — Telephone Technical Support and Repair  
Australia  
Hong Kong  
India  
Indonesia  
Japan  
1800 075 316  
2907 0456  
000 800 440 1193  
001 803 852 9825  
03 3507 5984  
Luxembourg  
Netherlands  
Norway  
Poland  
Portugal  
Russia  
Saudi Arabia  
South Africa  
Spain  
Sweden  
Switzerland  
800 23625  
0800 0227788  
800 11376  
00800 4411 357  
800 831416  
88005558588  
800 8 445 312  
0800 995 014  
900 938 919  
020 795 482  
0800 553 072  
Malaysia  
1800 812 612  
0800 450 454  
1800 144 10220 or 029003078  
800 810 0504  
800 616 1463  
New Zealand  
Philippines  
P.R. of China  
Singapore  
South Korea  
080 698 0880  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Country  
Telephone Number  
Country  
Telephone Number  
U.A.E.  
U.K.  
04-3908997  
0800 096 3266  
Honduras  
Jamaica  
Mexico  
AT&T +800 998 2112  
AT&T +800 988 2112  
1800 849 2273  
Mexico Local  
Monserrat  
Nicaragua  
Panama  
Paraguay  
+52-55-52-01-0004  
AT&T +800 998 2112  
AT&T +800 998 2112  
AT&T +800 998 2112  
AT&T +800 998 2112  
AT&T +800 998 2112  
AT&T +800 998 2112  
508 323 6234  
AT&T +800 998 2112  
AT&T +800 998 2112  
AT&T +800 998 2112  
AT&T +800 998 2112  
AT&T +800 998 2112  
AT&T +800 998 2112  
AT&T +800 998 2112  
AT&T +800 998 2112  
AT&T +800 998 2112  
You can also obtain support in this region using this URL:  
You can also obtain non-urgent support in this region at these email addresses:  
Technical support and general requests: [email protected]  
Return material authorization: [email protected]  
Contract requests: [email protected]  
Peru  
Puerto Rico  
Rest of Latin America  
St. Kitts Nevis  
St. Lucia  
St. Vincent  
Suriname  
Trinidad and Tobago  
Turks and Caicos  
Uruguay - Montevideo  
Venezuela  
Country  
Telephone Number  
Latin America — Telephone Technical Support and Repair  
Antigua  
AT&T +800 988 2112  
AT&T +800 988 2112  
AT&T +800 988 2112  
AT&T +800 988 2112  
AT&T +800 988 2112  
AT&T +800 988 2112  
AT&T +800 988 2112  
AT&T +800 988 2112  
AT&T +800 988 2112  
0800-133266 (0800-13-3COM)  
+5511 5643 2700  
AT&T +800 988 2112  
AT&T +800 988 2112  
AT&T +800 998 2112  
AT&T +800 998 2112  
+571 592 5000  
AT&T +800 998 2112  
AT&T +800 988 2112  
AT&T +800 998 2112  
AT&T +800 988 2112  
AT&T +800 988 2112  
AT&T +800 988 2112  
AT&T +800 988 2112  
AT&T +800 988 2112  
AT&T +800 998 2112  
AT&T +800 988 2112  
AT&T +800 988 2112  
Antigua Barbuda  
Argentina  
Aruba  
Bahamas  
Barbados  
Belize  
Bermuda  
Bolivia  
Brasil  
Brasil Local  
British Virgin Islands  
Cayman Islands  
Chile  
Colombia  
Columbia Local  
Costa Rica  
Curaçao  
Dominican Republic  
El Salvador  
Equador  
French Guyana  
Grenada  
Virgin Islands  
You can also obtain support in this region in the following ways:  
Spanish speakers, enter the URL:  
Portuguese speakers, enter the URL:  
English speakers in Latin America should send e-mail to:  
Country  
Telephone Number  
US and Canada — Telephone Technical Support and Repair  
All locations: All 3Com products: 1 800 876 3266  
Guadalupe  
Guatemala  
Guyana  
Haiti  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COPYRIGHT AND TRADEMARKS  
3Com Corporation, Corporate Headquarters, 350 Campus Drive, Marlborough, MA 01752-3064  
Copyright © 2008 3Com Corporation. All rights reserved.  
Copyright  
No part of any documentation supplied with this product may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation,  
or adaptation) without written permission from 3Com Corporation.  
3Com Technologies reserves the right to revise any documentation supplied with this product and to make changes in content from time to time without obligation on the part  
of 3Com Technologies to provide notification of such revision or change.  
3Com Technologies provides any documentation supplied with this product without warranty, term, or condition of any kind, either implied or expressed, including, but not limited  
to, the implied warranties, terms or conditions of merchantability, satisfactory quality, and fitness for a particular purpose. 3Com may make improvements or changes in the  
product(s) and/or the program(s) described in any documentation supplied with this product at any time.  
If there is any software on removable media described in any documentation supplied with this product, it is furnished under a license agreement included with the product as a  
separate document, in the hard copy documentation, or on the removable media in a directory file named LICENSE.TXT or !LICENSE.TXT. If you are unable to locate a copy,  
please contact 3Com and a copy will be provided to you.  
UNITED STATES GOVERNMENT LEGEND  
If you are a United States government agency, then any documentation supplied with this product and the software described therein are provided to you subject to the following:  
All technical data and computer software are commercial in nature and developed solely at private expense. Software is delivered as "Commercial Computer Software" as defined  
in DFARS 252.227-7014 (June 1995) or as a "commercial item" as defined in FAR 2.101(a) and as such is provided with only such rights as are provided in 3Coms standard  
commercial license for the Software. Technical data is provided with limited rights only as provided in DFAR 252.227-7015 (Nov 1995) or FAR 52.227-14 (June 1987), whichever  
is applicable. You agree not to remove or deface any portion of any legend provided on any licensed program or documentation supplied to you in connection with this product.  
Trademarks  
Unless otherwise indicated, 3Com registered trademarks are registered in the United States and may or may not be registered in other countries.  
3Com, the 3Com logo and OfficeConnect are registered trademarks of 3Com Corporation.  
All other company and product names may be trademarks of the respective companies with which they are associated.  
Please e-mail any comments about this document to 3Com at: [email protected]. Please include the document title, part number and if appropriate, the  
page number.  
3Com Corporation, Corporate Headquarters, 350 Campus Drive, Marlborough, MA 01752-3064  
Copyright © 2008 3Com Corporation. All rights reserved. 3Com, the 3Com logo, and OfficeConnect are registered trademarks of 3Com Corporation.  
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corporation.  
All other company and product names may be trademarks of their respective companies.  
Part Number 10016797 Rev CA Issued August 2008  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3M Printer Accessories 740B30 User Manual
Acer Projector PD311 User Manual
Actron Automobile Accessories CP9110 User Manual
ADTRAN Network Card ATM Mini DSLAM User Manual
AEG Clothes Dryer 88840 User Manual
Altec Lansing Portable Speaker 416 8B User Manual
Alto Shaam Oven MN 29492 User Manual
Audiovox Remote Starter 128 8110 User Manual
Axis Communications Security Camera P5532 User Manual
Azden Mixer FMX 42 User Manual