SERVICE MANUAL
TM
TOP-SIDE
COOKER
manufactured years
1998 - 2004
Keating Of Chicago, Inc.
1-800-KEATING
KEEP THIS MANUAL FOR TRAINING NEW PERSONNEL
NOTICE: This operating, installation, and service manual should be given to the user. The operator of the griddle
should be familiar with the functions and operation of the griddle. This manual must be kept in a prominent, easily
reachable location near the griddle.
Notice: Keating of Chicago, Inc. (manufacturer) reserves the right to change specifications at any time.
WARNING
FOR YOUR SAFETY
IMPROPER INSTALLATION, ADJUSTMENT,
DO NOT STORE OR
ALTERATION, SERVICE OR MAINTENANCE
CAN CAUSE PROPERTY DAMAGE, INJURY
USE GASOLINE OR
OTHER FLAMMABLE
OR DEATH. READ THESE INSTALLATION,
VAPORS OR LIQUIDS
OPERATING
AND
MAINTENANCE
IN THE VICINITY OF
THIS OR ANY OTHER
APPLIANCE.
INSTRUCTIONS THOROUGHLY BEFORE
INSTALLING
EQUIPMENT.
OR
SERVICING
THIS
WARNING
Before obtaining access to terminals,
all supply circuits must be disconnected.
ii
SAFETY
PRECAUTIONS
I INTRODUCTION
WARNING
GENERAL
THIS SYMBOL WARNS YOU THAT SERIOUS
BURNS OR OTHER INJURIES MAY RESULT IF
SAFETY INSTRUCTIONS ARE NOT FOLLOWED.
TM
Keating Top-Side Cookers are designed to give
maximum production efficiency, delivering high quality
food products. The following design features are
TM
TM
incorporated into Keating Top-Side Cookers.
ꢀ DO NOT SUBMERGE THE TOP-SIDE COOKING
HEAD IN WATER.
STANDARD
FEATURES
ꢀ Stainless steel control panel
ꢀ Stainless steel head cover
ꢀ MIRACLEAN® cooking surface
ꢀ Proprietary USDA and UL listed polymer cooking
sheets
ꢀ Electronic thermostat
ꢀ CLEANING CHEMICALS OR UTENSILS USED
FOR CLEANING GRIDDLES WILL DAMAGE OR
DESTROY THE POLYMER COOKING SHEET.
ꢀ NEVER USE A WATER JET TO CLEAN.
II INSTALLATION
TM
This Top-Side Cooker MUST be installed on a
Keating griddle only. Failure to do so voids the
warranty.
1
2
ꢀ Infinitely adjustable cooking height, from 1/8'' to 1 / ''
The Top-Side™ Cooker must be installed, inspected,
calibrated and serviced by qualified, certified and/or
licensed service personnel. Contact your dealer for
assistance.
(3mm to 38mm)
STANDARD
ACCESSORIES
ꢀ Proprietary USDA and UL listed polymer cooking
DAMAGE DURING
SHIPMENT
sheets (1)
TM
NOTE: Keating of Chicago, Inc. (manufacturer)
reserves the right to change specifications at any time.
The Top-Side Cooker has been assembled, tested
and inspected at the factory. Upon arrival, the complete
TM
Top-Side Cooker should be thoroughly checked for
any damage that may have occurred during shipment.
COOKING HEAD
SPECIFICATIONS
What to do if equipment arrives damaged:
TM
Each Top-Side cooking head is designed to be
VISIBLE LOSS OR DAMAGE- Be certain to note this
on the freight or express receipt and have it signed by
the delivery person.
connected to a 208, 220 or 240 volt single phase line.
HEIGHT WIDTH
DEPTH
WATTS AMPS
3-5/8''
10-1/2''
20''
4,000
18
(92mm)
(267mm)
(508mm)
@220V
@220V
FILE CLAIM FOR DAMAGES IMMEDIATELY-
Regardless of extent of damage.
STANDARD
TOP-SIDE™
COOKERS
CONCEALED LOSS OR DAMAGE- If the damage is
noticed when the equipment is unpacked, notify the
freight company immediately, and file a “concealed
damage claim”. This MUST be done immediately. Be
sure to retain the shipping container for inspection.
ꢀ Sizes: 1 to 6 heads.
ꢀ Mounting: Can be mounted to any standard
MIRACLEAN® gas or electric 30'' (762mm) deep
griddle (24'' deep plate / 610mm) up to 72" wide (up
to 6 heads maximum).
Keating does not assume responsibility for loss OR
damage incurred in transit.
1
2
ꢀ Cooking Surface: 10 / '' (267mm) wide x 20''
(508mm) deep (per cooking head).
INSTALLATION
ꢀ Number of heads: One head can be used for every
On new installations, your Top-Side™ Cooker has
already been factory installed, tested leveled and
inspected. When installing onto an existing
MIRACLEAN® griddle, use the specific instructions
included with the Top-Side™ Cooker.
TM
12'' (305mm) of plate width. Each Top-Side
cooking head will be positioned over a griddle
thermostat to ensure peak efficiency.
ꢀ ETL and ETL Sanitation listed.
1
ELECTRICAL
CONNECTION
TM
Each Keating Top-Side Cooking head is equipped
with a 9' (2.74m) neoprene covered, 12 gauge 4mm(2),
three wire with ground electrical cord. No plug is
provided. Each cooking head is rated 4000W, 18 amps,
single phase at 220 Volts (4.37kW, 19 amps, single
phase at 230 Volts) and is designed to be connected to
its own 208-240V single phase electrical supply. For
proper connecting and grounding procedure see local
codes, the National Electrical Code ANSI/NFPA 70
(latest edition) or Canadian Electrical Code CAN C22.1
(latest edition) as applicable.
2005-current model
NOTE: The green “Power On” light will be illuminated
as long as there is power to the Top-Side Cooker.
TM
COOKING HEIGHT
ADJUSTMENT
WARNING
TM
Keating’s Top-Side Cooker has been designed to
THIS APPLIANCE MUST BE EARTHED.
1
2
allow you infinite height adjustments from 1/8'' to 1 / ''
(approximately 3mm to 38mm). An adjusting knob
allows fast and precise height adjustment.
III OPERATING
CAUTION
Clockwise movement of the knob will increase the
spacing; counter clockwise movement will decrease
the spacing. Each turn of the adjusting knob represents
1/8'' (approximately 3mm) movement.
TM
Food will cook much faster with a Top-Side Cooker
Experimentation will give you the best cooking height
for each type of food product. The cooking head should
contact the product firmly to ensure optimum heat
distribution without flattening the product.
than with a griddle alone. Watch food while cooking or
use timers to ensure food will not be overcooked.
WARNING
TM
OPERATION OF THE TOP-SIDE
COOKER
PERSONNEL
OPERATING
SHUTDOWN
Turn ON/OFF switch to “OFF” position.
SHOULD
BE
LIMITED
TO
IN
THOROUGHLY
PROCEDURES.
TRAINED
CLEANING
PROCEDURES
A. Keating Cooking Sheets
COOKING
1.
Turn ON/OFF switch to “ON” position.
ꢀ Clean cooking sheets with a damp soft cloth after
2. Set thermostat to desired temperature. Red
“ELEMENT ON” light will illuminate when the
element is on.
each run of product (a Turkish towel works best).
Figure 3-1
TM
Top-Side Cooker Control Panel
pre-2005 model
Maximum thermostat setting 554°F (290°C)
2
ꢀ NEVER USE ICE TO COOL THE MIRACLEAN®
SURFACE AS IT MAY WARP THE MIRACLEAN®
SURFACE.
WARNING
THE COOKING HEAD WILL BE HOT. USE PROPER
CARE WHEN CLEANING THE COOKING SHEETS.
ꢀ USE ONLY KEATING SUPPLIED CLEANING
TOOLS AND KLENZER.
End of day cleaning:
ꢀ USE ONLY A KEATING STEEL SPATULA.
Before the griddle is turned off for the day, the cooking
sheets should be cleaned as described below. Wear
heat resistant gloves for maximum safety during the
entire cleaning procedure.
CAUTION
Do not hack, chop or hit the surface. You will dent the
steel plate under the trivalent chrome. It is even
possible to hack two nicks close together and actually
tear the MIRACLEAN® surface as the chromium will
not stretch. Below is a sketch showing a side view of a
cooking had and how the surface can be damaged.
Proper use of the utensils supplied with your
MIRACLEAN® Griddle will prevent surface damage.
1. At the end of the day, wipe the cooking sheet in
place with a damp soft cloth. Continue wiping until
the surface of the cooking sheet is free of any
residue.
2. Remove the cooking sheet from the cooking head.
Clean the cooking head and the griddle surfaces.
Surface Damage
3. Wash the cooking sheet with a mild detergent in
warm water and dry thoroughly.
4. After the cleaning is complete, reverse the cooking
sheet and reattach it to the cooking head.
B. Cooking Sheet Clips
To remove the stainless steel cooking sheet clips for
cleaning, simply lift them off. They can be cleaned in a
dishwasher.
C. Cooking Head
IV MAINTENANCE
The MIRACLEAN® surface is very durable and with
proper care, following the procedures below, will last
many years.
WARRANTY REPAIRS
1. Scrape MIRACLEAN® surface from front to back
with the Keating griddle scraper with Cooking
Sheets removed.
Keating’s warranty begins with the date of installation.
In the event your Keating Top-Side™ Cooker needs
repair under warranty other than routine maintenance
or cleaning you are requested to contact KEATING OF
CHICAGO, INC. at 1-800-KEATING before calling a
local service company.
2. Clean and polish surface wit Keating Klenzer on a
damp soft cotton cloth. Wipe off excess Klenzer.
NOTE: Keating Klenzer MSDS Sheet available online
NOTE: The cooking sheets are not covered under
warranty.
WARNING
PREVENTIVE
BECAUSE OF THE SUPERIOR MIRACLEAN®
SURFACE, THE ONLY TOOLS YOU WILL EVER
NEED TO CLEAN THE TOP-SIDE™ COOKING
HEAD ARE A DAMP SOFT COTTON CLOTH AND A
KEATING SCRAPER.
MAINTENANCE
Preventive maintenance should be done in daily,
weekly, monthly and yearly intervals as necessary.
Following preventive maintenance procedures will help
keep your Top-Side Cooker working efficiently.
Proper care and servicing will lead to years of quality
performance.
TM
ꢀ NEVER USE
A
GRIDDLE STONE, BRICK,
GRIDDLE SCREEN OR HARSH CHEMICALS TO
CLEAN THE MIRACLEAN® SURFACE.
ꢀ DAMAGE DONE TO THE MIRACLEAN® SURFACE
BY GRIDDLE STONE, BRICK, SCREEN, OR
HARSH CHEMICALS WILL VOID THE WARRANTY.
ꢀ THE DAMAGE DONE TO THE MIRACLEAN®
SURFACE IS IRREPARABLE.
3
PREVENTIVE MAINTENANCE CHART
Cooking sheets should never:
ꢀ Be folded or creased.
ꢀ Be touched with sharp objects.
ꢀ Come in contact with griddle scrapers or abrasive pads.
ꢀ Be placed under other equipment or objects.
Cooking sheets should always:
TIME
OPERATOR/OWNER
SECTION
FRAME
ꢀ Clean all cooking sheets.
ꢀ Clean all MIRACLEAN®.
cooking surfaces.
III
Daily
III
ꢀ Clean all surfaces of
ꢀ Be wiped with a damp soft cotton cloth after each run
Weekly
TM
Top-Side Cooker.
to remove any product residue.
ꢀ Verify thermostat settings
ꢀ Review cooking procedures.
ꢀ Check Cooking Sheets (replace
if necessary).
ꢀ Be cleaned after the griddle is shut down for the day.
The time to change a Cooking Sheet is when:
IV & V
III
Monthly*
ꢀ Product starts sticking to the sheet.
ꢀ Too much carbon build-up causes a product
Yearly*
QUALIFIED SERVICE
PERSONNEL ONLY
IV & V
appearance, cooking or taste problem.
ꢀ Thoroughly check and test
ꢀ The head surface is cool.
ꢀ If the sheet is torn or ripped.
TM
Top-Side Cooker.
ꢀ Calibrate controls.
*High production facilities should be checked more often.
WARNING
TM
THE TOP-SIDE COOKING HEAD AND GRIDDLE
PLATE ARE HOT - USE PROPER CARE WHEN
CHANGING THE COOKING SHEETS.
Proper care should be taken to fully clean the Top-
TM
Side Cooker on a regular basis. The control panel
should be cleaned of any greasy residue with a damp
cotton cloth. Remove any residue from the ON/OFF
switch and the thermostat knob. Wipe down the
cabinet, sides and back on a regular basis.
LEVELING OF
COOKING HEAD(S)
The cooking head(s) were leveled at the factory.
NOTE: For best results, level griddle before checking.
INSTALLING A
Adjust legs to level griddle.
COOKING SHEET
TM
1. Raise Top-Side Cooking head completely.
REMOVING OF
COOKING HEAD
NOTE: To identify parts, refer to Figure 6-1 on page 6.
2. Lay the 20'' x 24'' (508mm x 610mm) cooking sheet
on the griddle plate with 20'' (508mm) dimension
front to back.
TM
1. Turn off griddle and disconnect Top-Side™ Cooker
electric power.
3. Lower the Top-Side Cooker head onto the
cooking sheet, ensuring that the sheet is centered
under the head, the front edge of the sheet is even
with the front edge of the head, and the sides of the
sheet are parallel to the side of the head.
2. Remove the cooking sheet by lifting off cooking
sheet mounting clips.
3. Place a layer of soft cloth and then a layer of
cardboard onto griddle plate under cooking head to
protect MIRACLEAN® surface.
4. Fold both edges of the cooking sheet over the
head. While gently pulling the right side of the
sheet to remove any slack, firmly push the cooking
sheet mounting clip onto the right side mounting rib
on top of the head.
4. Raise cooking head completely to release tension
on cooking head support pin. Remove support pin
and its cotter pin and carefully lower cooking head
to protected griddle surface.
5. Repeat process on the left side.
6. Reverse the process to remove the cooking sheet.
WARNING
TIPS ON PROPER
HANDLING AND USE
OF COOKING SHEETS
To ensure long life of your Keating cooking sheets
please follow the tips below:
The cooking head is not supported after the
cooking head support pin has been removed. If
dropped the weight of the cooking head when
unsupported will cause damage to the griddle
surface or injury to personnel.
4
5. Do not turn the support pin in either direction.
V SERVICE DIAGNOSIS
6. To reattach the cooking head to the ram lift arm,
raise cooking head completely and replace
cooking head support pin. Insert a new stainless
steel cotter pin to secure support pin, holding
support pin to keep it from spinning.
TM
A properly adjusted Keating Top-Side Cooker, with no
1
1
2
2
load, will cycle “ON” approximately every 5 / to 6 /
minutes. Each cycle will last 40 seconds, ensuring that
the temperature setting is held within a narrow range.
7. Replace cooking sheet. See - “Installing a Cooking
Sheet”.
A. Trouble-Shooting
The following diagnosis is only to be used as a guide to
qualified service personnel. Keating recommends that
you use a qualified service company.
WARNING
Disconnect power before service.
PROBLEM
PROBABLE CAUSE
SOLUTION
TM
TM
POWER ON light does
not come on.
a. No electricity to Top-Side
a. Connect Top-Side Cooker to an
Cooker.
approved source of power.
b. Replace ON/OFF switch.
b. ON/OFF switch is faulty.
ELEMENT ON light does a. Connections to thermostat are
a. Check connections and tighten where
necessary. If thermostat is faulty,
replace.
not come on and cooking
head will not heat.
loose or thermostat is faulty.
b. Connections to thermostat
temperature probe are loose
or probe is faulty.
c. Hi-Limit has tripped or Hi-Limit is
faulty.
b. Check connections and tighten where
necessary. If probe is faulty, replace it.
c. Wait until cooking head cools down.
If ELEMENT ON light will not come
on Hi-Limit is faulty, replace it.
d. Check connections and tighten where
necessary.
d. Connections to Hi-Limit are
loose or Hi-Limit is faulty.
e. Connections to contactor are
loose or contactor is faulty.
f. ON/OFF switch is faulty.
e. Check connections and tighten where
necessary. If contactor is faulty, replace it.
f. Replace ON/OFF switch.
ELEMENT ON light does
not come on, but cooking
head does heat.
a. ELEMENT ON light is faulty.
a. Replace ELEMENT ON Iight.
(Element on light is part of the
thermostat)
ELEMENT ON light
flashes once whenever
power is turned on.
ELEMENT ON light
comes on, but cooking
head will not heat.
a. Thermostat temperature probe
or wires have shorted out.
a. Replace probe and/or wires.
a. Press Reset/Start switch.
a. Replace thermostat.
a. Cooker has not been reset.
a. If erratic, thermostat is faulty.
Temperature of cooking
head is erratic.
5
THERMOSTAT REPLACEMENT KIT (PART #057138)
MOUNTING AND WIRING INSTRUCTIONS
New Thermostat Mounting and Wiring Instructions
1. After removing the old thermostat, drill four larger holes for
mounting new housing (See Figure A). After drilling holes,
remove any metal filings from inside the unit.
2. Feed the female ends of the four new wires from the inside
to the outside of the unit through the old thermostat’s
mounting hole.
3. Connect the male ends of the four new wires to the female
ends of the wires that came off the old thermostat (L1, L2,
COM. and N.O.).
4. Feed the new sensor wire through the old thermostat’s
Figure A:
mounting hole.
Location of old thermostat mounting hole and where new holes
5. Remove the two spade connectors that are attached to
the unit thermostat’s sensor wire.
should be drilled.
6. Strip 3/8” of insulation from each of the four ends of the
thermostat’s sensor wires.
7. Place shrink tubing on both leads of the thermostat’s
sensor wire.
8. Attach the two pairs of thermostat wires using butt
connectors (See Figure C wiring diagram on reverse).
9. Shrink the tubing over the butt connectors on the
thermostat’s sensor wire.
10. Mount new housing to the control panel.
11. Connect all six wires to the new thermostat (See Figure C
wiring diagram on reverse).
12. Place the new thermostat in the housing and tighten the
four screws (See Figure B).
New thermostat Operating Instructions
Operating
When the thermostat is powered up, the display will show
the set operating temperature. To change the operating
temperature, push and hold the “PUSH TO SET” button
and turn the adjustment knob until the desired temperature
is displayed. Release the button to lock in the setting.
Figure B:
Temperature offset
New Thermostat Housing and Control Panel
To change the offset, power off the unit. Push and hold the
“PUSH TO SET” button, re-apply power to the unit while
still holding the button down. Turn the adjustment knob to
the desired amount of offset, release the button to lock in
the setting.
Adjust the setting to a positive number if the cooker’s
temperature is higher than the set temperature. Adjust the
setting to a negative number if the cooker’s temperature is
lower than the set temperature.
6
Part # 056840
Figure C:
Wiring Diagram
7
VI EXPLODED VIEW & PARTS LIST
ORDERING PARTS
Parts may be ordered by part number by calling 1-800-KEATING or your local service company. You may also order
Refer to the Keating Top-Side™ Cooker Limited Warranty for complete service and ordering information.
The model/serial plate for each cooking head is located on the the control panel assembly. The serial and model
numbers are necessary when ordering.
WARNING AND OPERATING PLATES
All warning and operating plates on the Keating Top-Side Cooker should be in place at all times. If plates are
damaged or lost, replace them immediately.
TM
TM
TOP-SIDE COOKING HEAD
Figure 6-1
To control box
8
TM
TOP-SIDE COOKING HEAD FOR MANUFACTURED YEARS 4/99 - 2004
Figure 6-1
PART
ITEM
DESCRIPTION
QTY.
NUMBER
1
2
THERMOSTAT TEMPERATURE PROBE KIT
COOKING HEAD (COMPLETE)
STOP CLEVIS PIN, S/S
SWIVEL BRACKET WIRE SLEEVE (INCL. IN ITEM 5)
SWIVEL BRACKET
SWIVEL BRACKET SUPPORT CLEVIS PIN, S/S
COOKING SHEET MOUNTING CLIP
COVER
COOKING SHEET (SINGLE SHEET)
COOKING SHEET (PACKAGE OF 12)
MIRACLEAN® COOKING FACE PLATE
HEATING ELEMENT 4KW, 220V (NOT SHOWN)
HIGH LIMIT PROBE
HIGH LIMIT PROBE MOUNTING PLATE
KNOB
COLLAR
WORM GEAR
1/4-20X 1/4" ALLEN SET SCREW
HOUSING COVER
WORM GEAR WHEEL
SPUR GEAR
SHAFT
1
1
1
1
1
1
2
1
016659
1-800-KEATING
015164
---
028181
015164
017316
1-800-KEATING
012118
012119
---
3
4
5
6
7
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
1
1
1
1
1
2
1
4
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
6
1
1
2
2
1
1
2
2
2
4
4
1
015046
015173
014247
028622
028486
028487
028501
028491
028488
030241
028461
028464
028518
028519
028521
028522
028490
028500
052114
052266
052251
054444
015262
052269
052287
030269
015414
032328
052117
052286
032327
013217
016383
------
REAR COVER
FRONT HOUSING
REAR HOUSING
FRONT PLUNGER
REAR PLUNGER (NOT SHOWN)
TEFLON WASHER (NOT SHOWN)
FIBER WASHER (NOT SHOWN)
TOP-SIDE COOKER WELD. MANUAL
TOP-SIDE COOKER SPRING SUPPORT WELDMENT
MANUAL TOP-SIDE GAS SPRING LIFT
MANUAL TOP-SIDE COOKER GAS SPRING
SCREW 5/16-18 X 3/4 HEX HEAD ZINC PLATED
TOP-SIDE COOKER SUPPORT BRACE GAS
TOP-SIDE CONDUIT SUPPORT
NUT RIVET 1/4-20 X 5/8” 0.332 BODY
WASHER 1/4ID X 7/80D X 1/16 THK NICKEL
SCREW 1/4-20 X 3/4 SERRATED FLANGE LOCK
TOP-SIDE COOKER LIFT ARM ROD
U BOLT WITH MOUNTING PLATE
SCREW 10-24 X 3/8 SERRATED FLANGE LOCK
WASHER 0.190 ID X 0.5630 D X 0.047 THK NICKEL
MANUAL TOP-SIDE COOKER GAS SPRING ROD
NUT 1/4-20 HEX NICKEL PLATED
3/8-2”1/2 CLEVIS PIN
015164
015166
014226
017046
015227
033828
COTTER KEYS S.S.
1/4-20 X 3” THREADED ROD
1/4” STAR WASHER
1/4-20 ACORN NUT
WELDMENT HANDLE GEAR GAPPING SYSTEM
9
TM
TOP-SIDE COOKER CONTROL PANEL
PART
NUMBER
ITEM
DESCRIPTION
QTY.
1
2
THERMOSTAT
1
1
1
1
1
1
1
1
1
1
1
1
1
1
057138
no longer available
no longer available
010311
THERMOSTAT KNOB
3
THERMOSTAT DIAL PLATE
HI-LIMIT CONTROL
HI-LIMIT MOUNTING BRACKET
CONTACTOR, 50A, 3-POLE
ROCKER SWITCH, LIGHTED, ON/OFF
INSTRUCTION PLATE ON/OFF SWITCH PLATE
INDICATING LIGHT, ELEMENT ON, RED 250V
INSTRUCTION PLATE ELEMENT ON LIGHT PLATE
TERMINAL BLOCK 3 POLE
COVER (without SERIAL PLATE)
CORD, WITHOUT PLUG, 12/3 SJO
PANEL TRAY
4
5
016654
6
011184
7
016689
8
016672
9
036933
10
11
12
13
14
016673
002565
------
018480
------
To cooking head
Thermostat as shown is no longer available - replacement part # listed above.
10
VII WIRING DIAGRAM
TM
TOP-SIDE COOKER WIRING DIAGRAMS
11
SERVICE INFORMATION
If you have a service related question call 1-800-KEATING.
Please state the nature of the call; it will ensure speaking with the appropriate person.
Have your serial and model number available when ordering parts.
KEATING OF CHICAGO, INC.
8901 West 50th Street, McCook, Illinois 60525-6001
Phone: (708) 246-3000 FAX: (708) 246-3100
Toll Free 1-800-KEATING (In U.S. and Canada)
*As continuous product improvement occurs, specifications may be changed without notice.
KEATING LIMITED WARRANTY CARD
PLEASE COMPLETE AND MAIL AT ONCE–WARRANTY IS NOT IN EFFECT UNTIL CARD IS RETURNED.
WARRANTY CARD IS ALSO AVAILABLE TO COMPLETE ON LINE AT YOUR CONVENIENCE.
COMPANY: ______________________________________________________________________________________________________
ADDRESS: ______________________________________________________________________________________________________
CITY: ____________________________________________________________________ STATE:________________ ZIP:____________
DEALER: ________________________________________________________________________________________________________
DATE OF PURCHASE:__________________________________________________________ INVOICE NUMBER: __________________
SERIAL NUMBER:____________________________________
REMARKS:__________________________________________
ꢁ FRYER
ꢁ FILTER SYSTEM
ꢁ GRIDDLE
ꢁ TOP-SIDE COOKER
ꢁ HOT PLATE ꢁ PASTA PLUS
I HAVE READ THE INSTALLATION AND OPERATION INSTRUCTIONS.
SIGNED: __________________________________________________________________________ DATE: ______________________
®
“Serving Those Who Serve The Very Best”
13
|