Hotpoint G320GIX User Manual

Cooking Hob  
ELECTROGAS  
Index  
GB  
GB  
English  
Instructions for use  
Installation, 4  
Use, 4  
Maintenance, 4  
Instructions for the installater  
Installation, 6  
Gas connection, 6  
Electrical connection, 6  
User characteristics, 7  
Assistance, 8  
THIS APPLIANCE IS CONCEIVED FOR  
DOMESTIC USE ONLY.THE MANUFACTURER  
SHALL NOT IN ANY WAY BE HELD  
RESPONSIBLE FOR WHATEVER INJURIES  
OR DAMAGES ARE CAUSED BY INCORRECT  
INSTALLATIONORBYUNSUITABLE,WRONG  
OR ABSURD USE.  
G320GIX  
G3201LIX  
Dear customer,  
We thank you and con-gratulate you on your  
choice. This new carefully de-signed product,  
manu-facturedwiththehighestqualitymaterials,  
has been carefully tested to satisfy all your  
cooking demands.We would therefore request  
you to read and follow these easy instructions  
which will allow you to obtain ex-cellent results  
right from the start. May we wish you all the  
very best with your modern appliance!  
THE MANUFACTURER  
GB  
Fig. 2  
Instructions for the installer  
Installation  
GB  
This appliance is not provided with a combu-stion  
product discharge. It is recommended that it be  
installed in sufficiently aerated places, in terms of the  
laws in force. The quantity of air which is necessary for  
combu-stion must not be below 2.0 m3/h for each kW of  
installed power. See table of burner power.  
ISO 7/1  
ISO 228/1 (FR)  
Fig. 3  
Positioning (Fig. 2)  
Electrical connection (Fig. 4)  
The appliance can be fitted into a working area  
as illustrated on the corresponding figure. Before  
positioning the hob, fit the seal  
Prior to carrying out the electrical connection, please  
ensure that:  
• the plant characteristics are such as to follow what is  
indicated on the matrix plate placed at the bottom of  
the working area;  
• thattheplantisttedwithanefficientearthconnection,  
following the standards and law provisions in force.  
The earth connection is compulsory in terms of the  
law.  
Should there be no cable and/or plug on the  
equipment, use suitable absorption material for the  
working temperature as well, as indicated on the matrix  
plate. Under no circumstance must the cable reach a  
temperature above 50°C of the ambient tempera-ture.  
If connecting directly to the mains power supply,  
fit a multi-pole switch of a suitable size for the rated  
capacity with a clearance distance which completely  
disconnects the power line under overvoltage category  
III conditions, consistently with the rules of installation  
(the yellow/green earth wir must not be interrupted).  
The plug or omnipolar switch must be easily reached  
on the installed equipment.  
around the entire  
X
periphery of the hole cut in the worktop.  
Gas connection (Fig. 3)  
Connect the appliance to the gas cylinder or to the  
installation according to the prescribed standards  
in force, and ensure beforehand, that the appliance  
matches the type of gas available. Otherwise, see  
“Adaptation to various types of gas”. Furthermore,  
check that the feed pressure falls within the values  
described on the table: “User chacteristics”.  
Rigid/semi rigid metal connection Carry out the  
connection with fittings and metal pipes (even flexible  
pipes) so as to obtain counter stress the inner parts of  
the appliance.  
N.B. - when the installation has been carried out, check  
the perfect sealing of the entire connection system, by  
using a soapy solution.  
Fig. 4  
Toavoidallrisk,ifthepowercablebecomesdamaged,  
it must only be replaced by the manufacturer,  
by an authorised service centre, or by a qualified  
electrician.  
GB  
wok C3 only  
Adaptation to various types of gas (Fig. 5)  
Should the appliance be pre-set for a different type of  
gas than that available, proceed as follows:  
• replace the injectors (Fig. 5) with the corresponding  
type of gas to be used (see table “Uses  
characteristics”).  
• to adjust to the minimum, use a screwdriver on the  
screw placed on the tap (Fig. 6) after turning the tap  
to its minimum position. For LPG (butane/propane)  
screw tight  
Fig. 5  
Fig. 6  
USER CHARACTERISTICS  
GAS BURNERS  
feed  
burner  
ø injecTors TherMal capaciTy  
Type  
pressure mbar  
noMinal  
W
consuMpTion  
norM.  
1/100 mm  
129  
77  
fast  
3000  
1000  
3500  
3000  
1000  
3500  
286  
95  
natural gas  
G20 20  
auxiliary  
wok 3  
fast  
141  
87  
333  
218  
73  
liquefied gas G30/G31 28-30/37 auxiliary  
wok 3  
50  
94  
254  
Assistance  
Before contacting After-Sales Service:  
GB  
1. See if you can solve the problem yourself.  
2. Switch the appliance on again to see if the problem  
has been solved. if it has not, disconnect the  
appliance from the power supply and wait for about  
an hour before switching on again.  
3. If the problem persists after this course of action,  
contact After-Sales Service.  
Specify:  
• the nature of the fault,  
• the model  
• the service number (the number after the word  
SERVICE on the rating plate on the rear of the  
appliance)  
• your full address,  
• your telephone number and area code.  
Never call on unauthorized technicians and always  
refuse to purchase non-original spare parts.  
The manufacturer declines all responsibility for possible inaccuracies contained in this pamphlet, due to printing or  
copying errors.We reserve the right to make on our own products those changes to be considered necessary or useful,  
without jeopardizing the essential characteristics.  
Notes  

HP Hewlett Packard Hewlett Packard Computer Monitor V185ES User Manual
GD Commerce International Inc Computer Hardware EDA M200 User Manual
Electrolux EHG 672 User Manual
Electrolux 269094 User Manual
Cypress CY7C68013A User Manual
Cypress CY7C1168V18 User Manual
CyberResearch GDR 15L TR User Manual
Compaq ProLiant 1850R User Manual
Compaq OXYGEN VX1 User Manual
AT T 9050 User Manual