Use andCare & Installation Guide
Gas Downdraft Cooktop
Safety Instructions................... 3–5
More questions?…call
GE Answer Center® 800.626.2000
Operating Instructions, Tips
Using Your Cooktop ................................. 8, 9
Vent System................................................. 10
Installation Instructions... 13–25
Downdraft............................................. 16–18
Consumer Services.................. 27
Important Phone Numbers....................... 27
Warranty ....................................... Back Cover
Care and Cleaning ................... 11, 12
Model: JGP645
GE Quality Product
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using this appliance.
IMPORTANT SAFETY NOTICE
• Be sure your cooktop is correctly adjusted by a
qualified service technician or installer for the
type of gas (natural or LP) which is to be used.
Your cooktop can be converted for use with either
type of gas. See the Installation Instructions.
• The California Safe Drinking Water and
Toxic Enforcement Act requires the Governor
of California to publish a list of substances
known to the state to cause cancer, birth
defects or other reproductive harm and requires
businesses to warn customers of potential
exposure to such substances.
• Do not attempt to repair or replace any
part of your cooktop unless it is specifically
recommended in this guide. All other servicing
should be referred to a qualified technician.
WARNING—TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended
by the manufacturer. If you have questions,
contact the manufacturer.
• Gas appliances can cause minor exposure to
four of these substances, namely benzene,
carbon monoxide, formaldehyde and soot, caused
primarily by the incomplete combustion of natural
gas or LP fuels. Properly adjusted burners,
indicated by a bluish rather than a yellow flame,
will minimize incomplete combustion. Exposure
to these substances can be minimized further by
venting with an open window or using the
ventilation fan.
B. Before servicing or cleaning the unit, switch
power off at the service panel.
C. When cutting or drilling into wall or ceiling
do not damage electrical wiring and other
hidden utilities.
When You Get Your Cooktop
D. Ducted fans must always be vented to the
When you get your cooktop, have the installer
show you the location of the gas cut-off valve
and how to shut it off if necessary.
outdoors.
E. To reduce the risk of fire, use only metal
ductwork.
• Have your cooktop installed and properly
grounded by a qualified installer, in accordance
with the Installation Instructions. Any adjustment
and service should be performed only by qualified
gas range installers or service technicians.
WARNING—TO REDUCE THE RISK
OF A COOKTOP GREASE FIRE:
A. Keep fan, filters and grease laden surfaces clean.
B. Always turn vent ON when cooking at high heat.
• Plug your cooktop into a 120-volt grounded
outlet only. Do not remove the round grounding
prong from the plug. If in doubt about the
grounding of the home electrical system, it is your
personal responsibility and obligation to have an
ungrounded outlet replaced with a properly
grounded three-prong outlet in accordance with
the National Electrical Code. Do not use an
extension cord with this appliance.
C. Use high settings on cooktop only when
necessary. Heat oil slowly on low to medium
setting.
D. Don’t leave the cooktop unattended when
cooking.
E. Always use cookware and utensils appropriate
for the type and amount of food being prepared.
CAUTION—For general ventilating use only.
Do not use to exhaust hazardous or explosive
materials and vapors.
• Be sure all packing materials are removed from
the cooktop before operating it, to prevent fire or
smoke damage should the packing material ignite.
(continued next page)
3
IMPORTANT SAFETY INSTRUCTIONS
(continued)
• For your safety, never use your appliance for
Using Your Cooktop
warming or heating the room.
• Do not leave children alone or unattended
where a cooktop is hot or in operation. They
could be seriously burned.
• Do not use water on grease fires.
Never pick up a flaming pan.
Turn the controls off. Smother a
• CAUTION: Items of interest to children should
not be stored in cabinets above a cooktop—
children climbing on the cooktop to reach items
could be seriously injured.
flaming pan on a surface burner by covering the
pan completely with a well-fitting lid, cookie
sheet or flat tray. Use a multi-purpose dry
chemical or foam-type fire extinguisher.
• When raising or lowering the vent, keep fingers
away from all vent parts; assure that cookware,
pans and handles will not be struck and tipped
when raising the vent.
Flaming grease outside a pan can be put out
by covering it with baking soda or, if available,
by using a multi-purpose dry chemical or foam-
type fire extinguisher.
• Do not operate or clean your cooktop if the
glass is broken or cracked. Cleaning solutions
and spillovers could penetrate the broken cooktop
and create a risk of electric shock. Call for service
immediately if the cooktop glass breaks or cracks.
• Do not store flammable materials near the
cooktop. Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
• Do not let cooking grease or other
flammable materials accumulate
on or near the cooktop.
• Clean the cooktop with caution. If a wet sponge
or cloth is used to wipe spills on a hot cooktop, be
careful to avoid steam burns.
• Never leave surface burners unattended at
high flame settings. Boilovers cause smoking
and greasy spillovers that may catch on fire.
• Do not clean the cooktop with flammable or
volatile cleaning fluids.
• Do not clean the cooktop when the appliance
is in use.
• Adjust surface burner flame size so it does
not extend beyond the edge of the cookware.
Excessive flame is hazardous.
• Avoid scratching the cooktop with sharp
instruments, or with rings and other jewelry.
• Use only dry pot holders—
moist or damp pot holders on hot
surfaces may result in burns from
• Never use the cooktop as a cutting board.
• Let the burner grates and other surfaces cool
before touching them or leaving them where
children can reach them.
steam. Do not let pot holders come near open
flames when lifting cookware. Do not use a towel
or other bulky cloth in place of a pot holder.
• Never wear loose-fitting or hanging garments
while using the appliance. Be careful when
reaching for items stored in cabinets over the
cooktop. Flammable material could be ignited if
brought in contact with flame or hot surfaces and
may cause severe burns.
• To minimize the possibility of burns, ignition
of flammable materials and spillage, turn
cookware handles toward the side or center
of the cooktop without extending over adjacent
burner or vent area.
4
• Always turn the surface burners to off before
removing the cookware.
• If the cooktop is located near a window,
do not use long curtains which could blow
over the burners and create a fire hazard.
• Carefully watch foods being fried at high
flame setting.
• If you smell gas, turn off the gas to the cooktop
and call a qualified service technician. Never use
an open flame to locate a leak.
• Foods for frying should be as dry as possible.
Frost on frozen foods or moisture on fresh
foods can cause hot fat to bubble up and over the
sides of the pan.
• Do not cover or block the area around the
cooktop knobs. This area must be kept clear for
proper ventilation and burner performance.
• Use least possible amount of fat for effective
shallow or deep fat frying. Filling the pan too
full of fat can cause spillovers when food is
added.
• When cooking pork, follow the directions
exactly and always cook the meat to an internal
temperature of at least 170°F. This assures that,
in the remote possibility that trichina may be
present in the meat, it will be killed and the meat
will be safe to eat.
• If a combination of oils or fats will be used
in frying, stir together before heating, or as fats
melt slowly.
• Do not use a wok on the cooking surface if
the wok has a round metal ring which is placed
over the burner grate to support the wok.
This ring acts as a heat trap which may damage
the burner grate and burner head. Also, it may
cause the burner to work improperly. This may
cause a carbon monoxide level above that allowed
by current standards, resulting in a health hazard.
• Always heat fat slowly, and watch as it heats.
• Use a deep fat thermometer whenever
possible to prevent overheating fat beyond
the smoking point.
• Use proper pan size—avoid pans that are
unstable or easily tipped. Select cookware having
flat bottoms large enough to properly contain food
and avoid boilovers and spillovers, and large
enough to cover burner grate. This will both save
cleaning time and prevent hazardous
accumulations of food, since heavy spattering or
spillovers left on cooktop can ignite. Use pans
with handles that can be easily grasped and
remain cool.
SAVE THESE
INSTRUCTIONS
• Do not place hot cookware on the glass
cooktop. This could cause glass to break.
• Keep all plastics away from burners.
• To avoid the possibility of a burn, always be
certain that the controls for all burners are at
the off position and all grates are cool before
attempting to remove a grate.
5
FEATURES OF YOUR COOKTOP
1
2
4
4
3
5
8
7
6
8
5
9
Explained
on page
Feature Index
1 Vent
2 Vent Filters
10
11
12
12
8
3 Cast-Iron Burner Grates
4 Spillproof Burners
5 High Power Spillproof Burners
6 Fan Speed Control
10
10
8
7 Vent Control
8 Surface Unit Controls
9 Glass Cooktop Surface
11
6
HOW DOES THIS COOKTOP COMPARE
TO YOUR OLD ONE?
Your new cooktop has gas burners. If you are used
The best types of cookware to use, plus heat-up and
cool-down times, depend upon the type of burner or
surface unit you have.
to cooking with induction or other electric surface
units, you will notice some differences when you use
gas burners.
The following chart will help you to understand the
differences between gas burner cooktops and any
other type of cooktop you may have used in the past.
Type of Cooktop
Gas Burners
Description
How It Works
Regular or sealed
gas burners use
either LP gas
Flames heat the pans directly. Pan flatness is not critical to cooking results, but
pans should be well balanced. Gas burners heat the pan right away and change
heat settings right away. When you turn the control off, cooking stops right away.
or natural gas.
Radiant
(Glass Ceramic)
Cooktop
Electric coils
under a glass-
ceramic cooktop.
Heat travels to the glass surface and then to the cookware, so pans must be flat on
the bottom for good cooking results. The glass cooktop stays hot enough to
continue cooking after it is turned off. Remove the pan from the surface unit if
you want cooking to stop.
Induction
High frequency
induction coils
under a glass
surface.
Pans must be made of ferrous metals (metal that attracts a magnet). Heat is
produced by a magnetic circuit between the coil and the pan. Heats up right away
and changes heat settings right away, like a gas cooktop. After turning the control
off, the glass cooktop is hot from the heat of the pan, but cooking stops right away.
Electric Coil
Flattened metal
tubing containing
electric resistance
wire suspended
over a drip pan.
Heats by direct contact with the pan and by heating the air under the pan. For best
cooking results, use good quality pans. Electric coils are more forgiving of
warped pans than radiant or solid disks. Heats up quickly but does not change
heat settings as quickly as gas or induction. Electric coils stay hot enough to
continue cooking for a short time after they are turned off.
Solid Disk
Solid cast iron
disk sealed to the
cooktop surface.
Heats by direct contact with the pan, so pans must be flat on the bottom for good
cooking results. Heats up and cools down more slowly than electric coils. The
disk stays hot enough to continue cooking after it is turned off. Remove the pan
from the solid disk if you want the cooking to stop.
7
USING YOUR COOKTOP
Electric Ignition
Your surface burners are lighted by electric ignition,
eliminating the need for standing pilot lights with
constantly burning flames.
In case of a power outage, you can light the surface
burners on your cooktop with a match. Hold a lighted
match to the burner, then turn the knob to the HIGH
position. Use extreme caution when lighting
burners this way.
The igniters make clicking sounds and spark even
when only a single burner is being turned on. Do not
touch any of the burners when the igniters are clicking.
Surface burners in use when an electrical power
failure occurs will continue to operate normally.
To Light a Burner
Push the control knob
in and turn it
counterclockwise to
desired position from
HIGH to LOW.
• The center and two rear burners are best for smaller
pans and cooking operations requiring carefully
controlled simmering conditions. The two front
burners are the high power burners for larger pans
and fast boiling operations.
• Do not operate a burner for an extended period
of time without cookware on the grate. The finish
on the grate may chip without cookware to absorb
the heat.
After the burner
ignites, turn the knob
in either direction to
adjust the flame size.
• Check to be sure the burner you turned on is the
one you want to use.
• Be sure the burners and grates are cool before you
place your hand, a pot holder, cleaning cloths or
other materials on them.
To turn a burner
off, turn the knob
clockwise, as far
as it will go, to the
OFF position.
Auto Relight
The burners on this cooktop relight automatically if the flame goes out.
This helps prevent the inconvenience of having to manually relight a burner.
As with electric ignition, all of the burner igniters spark while a burner is
relighting. Do not touch any of the burners when the igniters are clicking.
How to Select Flame Size
Watch the flame, not the knob, as you reduce heat.
The flame size on a gas burner should match the
cookware you are using.
FOR SAFE HANDLING OF COOKWARE, NEVER
LET THE FLAME EXTEND UP THE SIDES OF
THE COOKWARE. Any flame larger than the bottom
of the cookware is wasted heat and only serves to heat
the handle.
8
Cookware
Aluminum: Medium-weight cookware is
recommended because it heats quickly and evenly.
Most foods brown evenly in an aluminum skillet.
Use saucepans with tight-fitting lids for cooking with
minimum amounts of water.
Heatproof Glass Ceramic: Can be used for
either surface or oven cooking. It conducts heat
very slowly and cools very slowly. Check cookware
manufacturer’s directions to be sure it can be used
on gas cooktops.
Cast Iron: If heated slowly, most skillets will give
Stainless Steel: This metal alone has poor heating
properties, and is usually combined with copper,
aluminum or other metals for improved heat
distribution. Combination metal skillets generally
work satisfactorily if they are used at medium heat
as the manufacturer recommends.
satisfactory results.
Enamelware: Under some conditions, the enamel of
some cookware may melt. Follow cookware
manufacturer’s recommendations for cooking methods.
Glass: There are two types of glass cookware—
those for oven use only and those for surface cooking
(saucepans, coffee and teapots). Glass conducts heat
very slowly.
Wok Cooking
We recommend that you
use only a flat-bottomed
wok. They are available
at your local retail store.
Do not use woks that
have support rings.
Use of these types of
woks, with or without
the ring in place, can be
dangerous. Placing the
ring over the burner
grate may cause the burner to work improperly
resulting in carbon monoxide levels above allowable
current standards. This could be dangerous to your
health. Do not try to use such woks without the ring.
You could be seriously burned if the wok tipped over.
Stove Top Grills
Do not use stove top grills on your sealed gas burners.
If you use the stove top grill on the sealed gas burner it
will cause incomplete combustion and can result in
exposure to carbon monoxide levels above allowable
current standards. This can be hazardous to your health.
9
COOKTOP VENT SYSTEM
The built-in vent system helps remove cooking vapors, odors and
smoke from foods prepared on the cooktop.
Continuous use of the vent system helps keep the kitchen comfortable and
less humid, reducing cooking odors and soiling moisture that normally
creates a frequent need for cleaning.
Raising or Lowering the Vent
To raise the vent, turn the VENT knob to the
RAISE/LOWER position. The vent will rise to the
fully extended position. There is no intermediate
position.
To lower the vent, turn the VENT knob again to the
RAISE/LOWER position. The vent will then descend.
The vent fan will only operate in the fully extended
position.
How to Operate the Vent System
Turn the FAN knob to HIGH position to turn it on.
If you continue turning the FAN knob, you can select
a fan speed between HIGH and LOW.
The FAN knob does not have to be turned to OFF
before the vent is lowered. The fan will automatically
turn off when the vent is lowered.
If the fan was not turned off when the vent
was lowered, it will automatically come on
at the previously selected speed when the vent
is fully raised.
CAUTION: Be careful when raising or lowering
the vent. Be sure pots, pot handles and other objects
are clear of the vent cover and cannot be struck or
tipped by the vent being raised. Keep hands and
fingers away from all vent parts.
10
CARE AND CLEANING
Proper care and cleaning are important so your
Before cleaning any part of your cooktop, be sure all
burners are off and DISCONNECT ELECTRICAL
POWER TO THE COOKTOP at the fuse box or
circuit breaker panel, or pull the cooktop power plug,
located beneath the cooktop and inside the cabinets.
cooktop will give you efficient and satisfactory
service. Follow these directions carefully in caring
for it.
Glass Cooktop
To keep the cooktop looking its best, wipe up any
spills as they occur. This will keep them from burning
on and becoming more difficult to remove.
Do not use abrasive materials such as metal pads,
cleansing powder and scouring pads—they may
scratch the surface. Do not use harsh chemicals such
as bleach or chemical oven cleaners.
As soon as the cooktop is cool, wash the glass surface
with a cloth moistened with warm, soapy water; rinse
with clean water, and dry with a soft cloth. You can
use any liquid household detergent.
CAUTION: DO NOT COOK ON OR CLEAN A
BROKEN OR CRACKED COOKTOP. Cleaning
solutions and spillovers penetrating the cooktop can
create a risk of electric shock. Call for a service
technician immediately.
Grease Filters
The efficiency of your downdraft depends on a clean
filter. Frequency of cleaning depends on the type of
cooking you do. Grease filters should be cleaned at
least once a month. Never operate the downdraft
without the filters in place.
To remove: Lift up and pull the bottom out. Remove
the left filter first, then slide the right filter to the left
and remove it.
To clean: Soak and then agitate in a hot detergent
solution. Light brushing may be used to remove
imbedded soil. Rinse, shake and remove moisture
before replacing. Filters may be cleaned by placing in
dishwasher, although some slight color fading may
occur after several washings.
With careful handling, the filter will last for years. If
replacement becomes necessary, order the part from
your dealer.
Control Knobs
The control knobs may be removed for cleaning.
To remove knob, pull it straight up.
Wash knobs in soap and water but do not soak.
Avoid getting water down into the knob stem holes.
(continued next page)
11
CARE AND CLEANING
(continued)
Burner Assembly
The burner assemblies should be wiped clean often.
Turn all controls OFF before removing burner parts.
The electrode of the spark igniter is exposed
when the top of the burner is removed. Be careful
not to push in any surface unit controls while the
top of a burner is removed. A slight electrical
shock might result which could cause you to
knock over hot cookware.
Burner
grate
Burner cap
Slot
CAUTION: DO NOT OPERATE THE BURNER
WITHOUT ALL BURNER PARTS IN PLACE.
The burner grates and caps can be lifted off, making
them easy to clean. Removing them gives you access
to the burner base and burner bowl. Wash the grate
and cap in hot, soapy water and rinse with clean
water. Dry them with a cloth—don’t reassemble them
wet. When replacing these parts, be sure they fit
securely into position over the burners.
Burner
base
Burner bowl
Burner Grates
Cast-iron burner grates should be washed regularly
and, of course, after spillovers.
Wash them in hot, soapy water and rinse with clean
water. Dry the grates with a cloth—don’t put them
back on the cooktop wet. When replacing the grates,
be sure they’re positioned securely over the burners.
To get rid of burned-on food, place the grates in
a covered container or plastic bag. Add 1/4 cup
ammonia and let them soak for 30 minutes. Wash,
rinse well, and dry.
To prevent rusting, apply a light coating of cooking
oil on the bottom of the grates.
Although they’re durable, the grates will
gradually lose their shine, regardless of the best care
you can give them. This is due to their continual
exposure to high temperatures.
Do not operate a burner for an extended period
of time without cookware on the grate. The finish
on the grate may chip without cookware to absorb
the heat.
12
INSTALLATION INSTRUCTIONS
BEFORE YOU BEGIN
PARTS LIST
Read these instr uctions completely and
carefully.
Cooktop
• 4 burner grates
• 4 burner caps
Save these instr uctions for local inspector’s
use.
• Gas pressure regulator with attached 1/ 2″ to
IMP ORTANT–OBSERVE ALL GOVERNING
CODES AND ORDINANCES.
3/ 8″ reducing bushing and 3/ 8″ pipe nipple
• 2 clamping brackets with screws
NOTE TO INSTALLER: Be sure to leave
these instr uctions with the consumer.
• Attached 120 volt grounded plug cord
• Self adhesive gasket
1/ 4″ x 36″ (1)
3/ 16″ x 36″ (2)
FOR YOUR SAFETY
If YOU SMELL GAS:
Downdraft Unit
• Downdraft unit
• Downdraft stability brackets
• Two filters
1. Open windows.
Blower Unit
2. Don’t touch any electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.
for your safety
JXBA55 motor and blower assembly is required
for both models.
JXBC55 optional outdoor cover accessory may
be ordered for installation of blower and motor
assembly on the outside wall.
• Blower
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
• Nuts and washers
TOOLS AND PARTS NEEDED
• Large flat blade screwdriver
• Saw
• Carpenter’s square
• Pipe wrench
• Manual gas line shut-off valve
• Pipe joint sealant that resists action of LP gas
• Ductwork to suit the installation.
For flexible connection where local
codes per mit:
• Flexible metal tubing (same 3/ 4″ or 1/ 2″ I.D.
as gas supply line)
• Flare union adapter for connection to supply line
(3/ 4″ NPT x 3/ 4″ I.D. or 1/ 2″ NPT x 1/ 2″ I.D.)
• Flare union adapter for connection to
regulator (1/ 2″ NPT x 3/ 4″ I.D. or 1/ 2″ I.D.)
For rigid connection:
• Pipe fittings as required
(continued next page)
13
INSTALLATION INSTRUCTIONS
(continued)
DIMENSIONS AND CLEARANCES
IMPORTANT SAFETY INSTRUCTIONS
The cooktop has been design certified by the
American Gas Association. As with any appliance
using gas and generating heat, there are certain
safety precautions you should follow. You’ll find
these precautions in this Use and Care Guide;
read it carefully.
2″
1
36″
4
22 ⁄ ″
3
2″
4
8 ⁄ ″
15″
• Be sure your cooktop is installed properly
by a qualified installer or service technician.
13″
Max.
• The cooktop must be electrically grounded in
accordance with local codes, or in their absence,
with the National Electrical Code ANSI/ NFPA
No. 70–Latest Edition.
• Installation of this cooktop must conform with
local codes, or in the absence of local codes, with
the National Fuel Gas Code. ANSI Z223.1–Latest
Edition.
30″
Min.
18″
Min.
• Disconnect electrical supply before servicing.
8″ Min. to
• Make sure the wall coverings around the
cooktop can withstand heat generated by the
cooktop up to 200°F.
wall when
installed
8″ Min. to
wall when
installed
• Avoid placing cabinets above the cooktop.
• If cabinets are placed above the cooktop, allow
a minimum clearance of 30″ between the cooking
surface and the bottom of unprotected cabinets.
The downdraft system with blower, motor and
ductwork will occupy the cabinet below the
cooktop. Drawers cannot be installed below
this cooktop.
• If cabinets are placed above the cooktop, use
cabinets no more than 13″ deep.
• If a 30″ clearance between cooking surface and
overhead combustible material or metal cabinets
cannot be maintained, protect the underside of
the cabinets above the cooktop with not less than
1/ 4″ insulating millboard or gypsum board at
least 3/ 16″ thick covered with 28 gauge sheet
steel or 0.020″ thick copper.
Avoid placing cabinets above the cooktop unit,
if possible, in order to reduce the hazards caused
by reaching over heated surface units.
If the cabinetry is used above the cooktop,
allow a minimum 30″ clearance between the
cooking surface and the bottom of the
unprotected cabinet.
• Clearance between the cooking surface and
protected cabinets MUST NEVER BE LESS
THAN 2 4 ″. The vertical distance from the plane
of the cooking surface to the bottom of adjacent
overhead cabinets extending closer than 1″ to
the plane of the cooktop sides must not be less
than 18″.
If the clearance between the cooktop and the
cabinetry is less than 30″, the cabinet bottom
must be protected with a flame retardant
millboard at least 1/ 4″ thick, or gypsum board
at least 3/ 16″ thick, covered with 28 gauge sheet
steel or 0.020″ thick copper. Clearance between
the cooktop and the protected cabinetry MUST
NEVER BE LESS THAN 2 4 ″.
EXCEP TION: Installation of a listed microwave
oven or cooking appliance over the cooktop shall
conform to the installation instructions packed
with that appliance.
Working areas adjacent to the cooktop should
have an 18″ minimum clearance between the
countertop and the bottom of the cabinet.
If the clearance is less than 18″, the adjacent
cabinets should be at least 8″ from the side
of the cooktop.
14
CUT THE OPENING
PREPARING THE COUNTERTOP
2″
Back of countertop
1
36″
4
22 ⁄ ″
5/16″
2″
2″
3
4
8 ⁄ ″
15
16
33 ⁄ ″
15″
15
16
33 ⁄ ″
1
21″
4
1 ⁄ ″
19″
19″
Min.
9
16
34 ⁄ ″
21″
1
4
2 ⁄ ″
Min. to
front
13
9
16
8 ⁄ ″
16
34 ⁄ ″
Min. to
side walls
Front of countertop
edge
2″
Countertop cut-out dimensions
5
16
⁄ ″
Cut out the opening as shown in the diagram.
Measure carefully when cutting the countertop.
Making sure the sides of the opening are parallel
and the front and rear cuts are exactly
perpendicular to the sides.
Measure carefully when cutting countertop.
Make sure sides of opening are parallel and rear
and front cuts are exactly perpendicular to sides.
The gas downdraft cooktop is designed to fit in a
The front of the opening must clear the front
support rail on the cabinet and the rear of the
opening must clear the rear support of the cabinet.
36″ or larger base cabinet.
The counter top cutout for the cooktop
must be:
9
15
16
16
• 34 ⁄ ″ at the front of the counter and 33 ⁄ ″ at
the back
• 19″ front to back notch
• 21″ front to back of cutout
The notches at the back of the cutout are:
• 2″ forward and 5/ 16″ to the inside.
Follow the illustration shown.
1
4
• Allow at least 1 ⁄ ″ clearance between back of
cutout and wall.
13
16
• Allow at least 8 ⁄ ″ clearance from right and
left sides of cutout to adjacent wall.
1
4
• Allow at least 2 ⁄ ″ clearance between front of
cutout and front edge of countertop.
CAUTION: Wall coverings, countertops and
cabinets should be able to withstand 200°F. heat
generated by the cooktop.
(continued next page)
15
INSTALLATION INSTRUCTIONS
(continued)
PLAN THE DUCTWORK
DUCTWORK ARRANGEMENT
2″
1
4
2 ⁄ ″
15″
1
4
3 ⁄ ″
Right
discharge
Transition (supplied
with blower/motor)
1
4
3 ⁄ ″
1
2
7 ⁄ ″
Left discharge
(as shipped)
10″
1
4
3 ⁄ ″
The downdraft vent is shipped with the
discharge outlet on the left side. It can be
changed to the right side to avoid interference
in routing the ductwork.
Adjustable
5″ to 8″
1
4
13 ⁄ ″
• To change the ductwork to the right side,
remove the screws holding the outlet panel to
the bottom of the vent.
P repare ductwork to vent to outdoors:
• Remove and rotate the panel and fasten with
screws.
• Use the shortest and straightest duct run
possible.
• The blower can be mounted in the cabinet or
under the floor. The blower will fit between floor
joists on 16″ centers.
• Duct run should not exceed equivalent length
of 150 feet. Refer to “Duct Fittings” chart to
calculate equivalent length for various duct
configurations.
• This downdraft blower system is designed for
1
4
use with 3 ⁄ ″ x 10″ ductwork. It can be
transitioned to 6″ round.
• Ductwork MUST be vented to the outside.
Never vent into a crawl space, attic or other
enclosed space.
16
To accurately locate the ductwork holes in
the cabinet floor:
• Place the downdraft vent against the back of
the cutout.
• Place the transition duct supplied on top of the
blower/ motor assembly.
5
16
10 ⁄ ″
• Position the transition duct and assembly
below the discharge outlet.
1
4
1 ⁄ ″ From
back wall
• Position a transition duct (not supplied) to the
end of the blower in the direction of desired
discharge.
1
4
3 ⁄ ″ x 10″
• Mark the location and remove the assembly.
• Cut the holes and install ductwork connection.
C
L
5
16
10 ⁄ ″
1
4
1 ⁄ ″ From
back wall
Discharge right shown with 6″ round duct
(not shown to scale)
1
4
3 ⁄ ″ x 10″
C
L
1
16
7 ⁄ ″
Discharge left shown with rectangular duct
(not shown to scale)
1
4
1 ⁄ ″ From
back wall
1
4
3 ⁄ ″ x 10″
(continued next page)
Through the floor shown with rectangular duct
(not shown to scale)
17
INSTALLATION INSTRUCTIONS
(continued)
Total
Equivalent Number Equivalent
DUCT FITTINGS
Use the chart at the right to compute maximum
permissible lengths for duct runs to outdoors.
NOTE: Do not exceed maximum permissible
equivalent lengths!
Duct Pieces
Length*
Used
Length
1 ft.
6″ round,
straight
(per foot
length)
feet
1 ft.
1
Flexible ducting:
4
3 ⁄ ″ x 10″
(per foot
straight
length)
15 ft.
9 ft.
feet
If flexible metal ducting is used, all the
equivalent feet values in the table should be
doubled. The flexible metal duct should be
straight and smooth and extended as much
as possible.
6″, 90°
elbow
6″, 45°
elbow
Do NOT use flexible plastic ducting.
NOTE: Any home ventilation system, such as a
cooktop with a downdraft exhaust mechanism,
may interrupt the proper flow of combustion air
and exhaust required by fireplaces, gas
furnaces, gas water heaters and other naturally
vented systems. To minimize the chance of
interruption of such naturally vented systems,
follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by NFPA and ASHRAE.
1
4
3 ⁄ ″ x 10″
90° elbow
16 ft.
5 ft.
1
4
3 ⁄ ″ x 10″
45° elbow
1
4
3 ⁄ ″ x 10″
90° flat elbow
18 ft.
6″ round
1
4
to 3 ⁄ ″ x 10″
transition
7 ft.
5 ft.
1
4
3 ⁄ ″ x 10″
to 6″ round
transition
6″ round
1
4
to 3 ⁄ ″ x 10″
transition
90° elbow
20 ft.
1
4
3 ⁄ ″ x 10″
to 6″ round
transition
90° elbow
12 ft.
21 ft.
6″ round wall
cap with damper
1
4
3 ⁄ ″ x 10″ wall
cap with damper
27 ft.
20 ft.
24 ft.
6″ round
roof cap
6″ round
roof vent
Total duct run should not exceed 150 ft.
*Actual length of straight duct plus duct fitting
equivalent. Equivalent length of duct pieces are
based on actual tests conducted by GE Evaluation
Engineering and reflect requirements for good
venting performance with any downdraft cooktop.
18
POWER SUPPLY LOCATIONS
Electrical Supply:
Gas Supply:
These cooktops are designed to operate on
natural gas at 4″ of water column pressure or
on LP gas at 10″ of water column pressure.
• These cooktops are shipped from the factory
set for natural gas. If you decide to use this
cooktop with LP gas, conversion adjustments
must be made by a service technician or other
qualified person.
19″
4″
Electric location
• The pressure regulator must be connected in
series with the manifold of the cooktop and must
remain in series with the supply line regardless
of type of gas being used.
14″
Gas location
For proper operation, the maximum inlet
pressure to the regulator must be no more than
10″ water column pressure for natural gas and
14″ water column pressure for LP gas.
The built-in gas downdraft cooktop features
pilotless electric ignition for energy savings and
reliability. It operates on a 120 volt, 60 Hz power
supply. A separate circuit, protected by a 15 amp
time delay fuse or circuit breaker, is required.
• When checking the regulator, the inlet
pressure must be at least 1″ greater than the
regulator output setting.
If the regulator is set for 4″ of water column
pressure, the inlet pressure must be at least 5″.
• A properly grounded 3-prong receptacle
should be located within reach of cooktop’s four
foot power cord.
If the regulator is set for 10″ of water column
pressure, the inlet pressure must be at least 11″.
For ease of installation, and if local codes permit,
the gas supply line into the cooktop should be
1/ 2″ or 3/ 4″ ID flexible metal appliance
connector, three to five feet long.
IMP ORTANT: (P lease read carefully.)
FOR P ERSONAL SAFETY, THIS
AP P LIANCE MUST BE P ROP ERLY
GROUNDED.
NOTE: Purchase a new flexible line. DO NOT
USE AN OLD P REVIOUSLY USED LINE.
The power cord of this appliance is equipped
with a three-prong (grounding) plug which
mates with a standard three-prong grounding
wall receptacle to minimize the possibility of
electric shock hazard from this appliance. The
customer should have the wall receptacle and
circuit checked by a qualified electrician to
make sure the receptacle is properly grounded
and has correct polarity.
• Make gas connection through rear wall, or on
cabinet floor at rear, as illustrated.
Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the customer to have it replaced
with a properly grounded three-prong wall
receptacle.
Do Not, Under Any Circumstances, Cut Or
Remove The Third (ground) P rong From
The P ower Cord.
Do not use an extension cord.
(continued next page)
19
INSTALLATION INSTRUCTIONS
(continued)
STEP 1
STEP 3
Install Downdraft Vent
Install the Motor/Blower Assembly
Place the downdraft vent into the countertop
cutout, against the back side.
• Secure the transition duct to the top of the
assembly with 2 screws on each side.
• Position the assembly with duct below the
vent discharge.
• Adjust the height by sliding the brackets up or
down until the assembly is tight against the vent
discharge.
Countertop
Countertop
• Tighten all nuts and bolts on the brackets.
Tighten bolt
• Install discharge transition onto the blower
and connect to ductwork. If round ducting
is used, transition to 6″ round to connect to
the inlet.
Tighten
against
Bolt
countertop
Against
Countertop
STEP 4
• Secure the downdraft to the countertop with
mounting screws provided. (One on each side.)
Tighten the mounting screws against the
underside of the countertop.
Install the Ductwork
Use minimum 26 gauge galvanized or 24 gauge
1
4
• Use a wood shim when installing in stone
countertops.
aluminum duct in 6″ round or 3 ⁄ ″ x 10″ size, or
a combination of both. PVC duct should be used
if installing under a poured concrete slab. DO
NOT use flexible plastic ducting.
• When installing in a tile countertop surface, it
may be necessary to apply a locally approved
caulking to cover any gaps.
• Always use an appropriate roof or wall cap
with damper. Laundry type wall caps should
never be used.
• Fasten stabilizing straps to each side with
screws provided.
• Use the straightest duct run possible.
• Secure the other end of the strap to the back
or side wall of the cabinet.
• For satisfactory performance the duct run
should not exceed 150 ft. or its equivalent length
if bends or other various fittings are used. Refer
to table of equivalent lengths for various duct
configurations.
STEP 2
Install Adjustable Support Brackets
• Place 2 brackets together, with ends facing the
same direction. Secure with bolts, lock washers
and nuts. Do not tighten.
Duct tape over
Duct Tape
seam and screw
Over Seam and Screw
Air
• Assemble all 4 brackets and secure to the
bottom of the blower/ motor assembly.
Flow
Air flow
• For installation where the blower is mounted
inside the cabinet, attach the support brackets to
the corners of the blower housing.
Screw
Screw
• If the blower is installed under the floor, attach
the support brackets to the top of the blower.
Provide a surface to attach the entire assembly
to the underside of the floor.
• Install ductwork so that the piece of duct
nearest the downdraft unit slots INTO the next
piece of the duct. Secure the joints with self-
tapping screws and apply duct tape around the
joints to ensure an airtight seal.
• Support brackets are adjustable from 5″ to 8″.
20
STEP 5
STEP 6
Install the Pressure Regulator
Install the Cooktop
NOTE: If the cooktop is installed into a 36″
base cabinet, the pressure regulator MUST BE
installed to the bottom of the cooktop before the
cooktop is placed into the cabinet.
Regulator
• Remove packaging from the cooktop.
Solid piping or
flexible connector
Shut-off
valve
Pipe stub
• Install the supplied pressure regulator and
nipple in the gas line as close to the cooktop
inlet as possible. Allowances for ventilation
ducting may be necessary.
• To insure a good fit, position the cooktop over
the cutout opening and carefully lower into
place. Check edges all the way around to be
sure all cutout edges are concealed and there
are no gaps.
Make sure the regulator is installed in the right
direction.
• Carefully lift and remove the cooktop.
• Install a manual shut-off valve in the gas line
in an easily accessible location.
(continued next page)
NOTE: Instead of using solid piping to connect
to pressure regulator, an approved flexible metal
appliance connector may be used between the
pipe stub and the shut-off valve and the pressure
regulator, if local codes permit.
Appropriate flare nuts and adapters are required
at each end of the flexible connector.
• Turn on the gas. Check for leaks using a
liquid leak detector at all joints in the system.
(The pressure test nipple is adjacent to the gas
inlet pipe on the rear right hand side of the
cooktop bottom.)
CAUTION: DO NOT USE A FLAME TO
CHECK FOR GAS LEAKS.
IMP ORTANT: Disconnect the cooktop and the
individual shut-off valve from the gas supply
piping system during any pressure testing of
that system at test pressures greater than 1/ 2
psig. Isolate the cooktop from the gas supply
piping system by closing the individual manual
shut-off valve to the cooktop during any
pressure testing of the gas supply piping system
at test pressures equal to or less than 1/ 2 psig.
21
INSTALLATION INSTRUCTIONS
(continued)
STEP 6
STEP 7
Install the Cooktop (continued)
Electrical Connections
1/16″
3/8″
• Connect the 3-pin plastic plug from the
blower/ motor assembly to the 3-pin plastic
socket on the underside of the vent, next to the
conduit.
• Cut a 3/ 16″ gasket strip in half. Peel off the
backing and apply to the underside of the glass
cooktop edge, on each side at least 3/ 8″ from
the back and as close to the edge as possible
without protruding.
• Slide the metal cover over the connection and
secure with screws.
Service
plate
Electrical
6-pin socket
• Apply the other gasket strip to the underside
of the glass at the front of the cooktop.
Electrical
supply cord
• Remove remaining adhesive backing.
6-Pin
plug
• Position the cooktop over the opening, making
sure that the power cord is dropped into the
cabinet.
Pressure
regulator
Metal
cover
• Lower the cooktop into the cutout, pressing
gently and evenly to seat.
NOTE: If the cooktop is installed in a 36″ base
cabinet, the mounting brackets cannot be used
because of interference with the cabinet sides.
In this case, the cooktop can be secured to the
cabinet with angle brackets (not supplied).
• Connect the 6-pin plastic plug from the
downdraft assembly to the 6-pin plastic socket
on the underside of the cooktop, next to the
power cord.
• Slide the metal cover over the connection and
secure with screws.
Remove one screw
at the bottom of
the cooktop body
on both sides and
secure the bracket
with those screws.
Then, secure the
brackets to the
Gasket
Gasket
Countertop
Countertop
STEP 8
Connect Power
Plug power cord into properly grounded
receptacle.
cabinet sides.
• Insert hold-down
bracket into
highest slots on
the right and left
sides of the
cooktop.
Cooktop has three slots, the highest available will
depend on the thickness of the countertop.
• Secure the brackets to the underside of the
countertop with screws provided.
22
STEP 9
STEP 10
Assemble Burners, Check Ignition
Install Filters, Check Operation of Downdraft
Assemble burner as shown.
To raise the vent, turn the VENT knob to
RAISE/ LOWER.
• Hold the knob until the vent begins to raise.
The vent will automatically stop when it is fully
extended.
Top grate
Burner cap
• Tip filter into the opening and pull straight
down so that the filter rests on slides.
Check for proper ignition:
• Push in one control knob and turn 90° to
HIGH position.
• The igniter will spark and the burner will
light; the igniter will cease sparking when the
burner is lit.
• First test may require some time, while air is
flushed out of the gas line.
• Slide the filter to the right side.
• Turn knob to OFF.
• Repeat the procedure for each burner.
• Tip the other filter into the opening and pull
straight down.
• To turn the fan on, turn the FAN knob to
HIGH. Continue turning the FAN knob to select
a fan speed between HIGH and LOW.
NOTE: It is not necessary to turn the fan
OFF before lowering the vent. The fan will
automatically turn off when the vent is lowered.
When the fan is not turned off before lowering
the vent, it will automatically come on at the
previously selected speed when the vent is
fully raised.
To lower the vent, turn the VENT knob to
RAISE/ LOWER. Hold the knob until the vent
begins to lower.
23
CONVERTING TO LP GAS
or Converting Back to Natural Gas from LP
WARNING: If you are using LP (bottled) gas, all
adjustments described in the following steps must be
made before attempting burner adjustments or use of
the cooktop.
2
CONVERT THE SURFACE KNOBS
This cooktop leaves the factory set for use with
natural gas. If you convert to LP gas, keep these
instructions and orifices in case you want to convert
back to natural gas.
Cam
Valve
shaft
The conversion should be done by a qualified
technician or installer.
1 . Remove the knobs and lift off the microswitch
operating cams from the valve shafts.
PARTS:
2 . Fully screw down the brass low flame
adjustment screws into the valve bodies with a
clockwise rotation.
Check the contents of the kit, which should
contain the following:
• 2 Orifices—Large size—104-WB28K0093
• 3 Orifices—Small size—82-WB28K0094
• 1 Maxitrol LP adapter—WB01K055
• 1 Tie-on card/ label for regulator
If you do not have all the above listed components,
or if you are in any doubt, please contact the nearest
GE Service and Parts Center.
3 . Replace the knobs and cams.
3
CONVERT THE SURFACE BURNERS
Top grate
USE ONLY APPROVED PIPE DOPE RESISTANT
TO LP GAS.
Total input rating after conversion:
• 4 burner cooktop 34,000 Btu/ hr.
Burner cap
TOOLS REQUIRED:
Adjustable wrench
Nut drivers: 9/ 32″ or 7 mm
1 . Remove grates and burner caps.
2 . Using the 7 mm nut driver,
remove and replace the brass
orifice spud inside each burner
chimney as follows:
1
PREPARE COOKTOP FOR CONVERSION
(1) Tur n off gas supply at the shut-off valve.
(2) Turn off the electrical power to the cooktop.
• Replace the large orifices with
the spuds that are stamped 104.
• Replace the small orifices with
the spuds that are stamped 82.
NOTE:
• Each orifice has a number and the letter “L”
indicating LP gas.
• There will be one extra orifice spud when
converting a four burner cooktop.
24
CONVERTING TO LP GAS
or Converting Back to Natural Gas from LP
6
4
CONVERT THE PRESSURE REGULATOR
CHECK QUALITY OF FLAMES
The combustion quality of burner flames needs
to be determined visually.
WARNING: Do not remove the pressure
regulator from the cooktop.
(A) Yellow flames—
Call for service
1 . Locate the pressure regulator under the rear
of the cooktop.
2 . Use an adjustable wrench to remove the
(B) Yellow tips on
outer cones—
Normal for LP gas
nut from the pressure regulator.
Gas flow
into range
(C) Soft blue flames—
Normal for natural gas
LP
LP adapter
If burner flames look like (A), call for service.
Normal burner flames should look like (B) or
(C), depending on the type of gas you use.
Nut
NAT
With LP gas, some yellow tipping on outer
cones is normal.
3 . Insert the LP Adapter into the nut.
LP
NAT
7
LP
adapter
FINAL STEPS
Fill in the date plus the name and address of the
service organization performing the conversion
in the spaces provided on the conversion label.
Remove the backing from the label and stick it in
a convenient place on the underside of the
cooktop near the Rating Plate. Make sure the
area is clean and dry before applying the label.
Nut
4 . Reinsert the assembly into the regulator and
attach the tie-on label to the regulator using the
string provided.
The conversion is now complete.
5
CHECK FOR LEAKS
Check for leaks before attempting to light the
burners.
When all connections have been made, make
sure all cooktop controls are in the OFF position
and turn on the main gas supply valve. Use a
liquid leak detector at all joints and connections
to check for leaks in the system.
CAUTION: DO NOT USE A FLAME TO
CHECK FOR GAS LEAKS.
When using test pressures greater than 1/ 2 psig
to pressure test the gas supply system of the
residence, disconnect the cooktop and individual
shut-off valve from the gas supply piping. When
using test pressures of 1/ 2 psig or less to test the
gas supply system, simply isolate the cooktop from
the gas supply system by closing the individual
shut-off valve.
25
QUESTIONS?
BEFORE YOU CALL FOR SERVICE…
PROBLEM
POSSIBLE CAUSE
BURNERS DO NOT
LIGHT
• Make sure electrical plug is plugged into a live power outlet.
• Slot in burner base may be clogged. Remove the obstruction.
• Burner parts not replaced correctly.
• Hole in burner cap behind igniter may be clogged.
BURNERS HAVE
YELLOW OR
YELLOW-TIPPED
FLAMES
(A) Yellow flames — (B) Yellow tips on outer (C) Soft blue flames —
Call for service
cones — Normal for
LP gas
Normal for
natural gas
• If burner flame looks like (A), call for service. Normal burner flames
should look like (B) or (C), depending on the type of gas.
BURNER FLAMES VERY
LARGE OR YELLOW
• If cooktop is connected to LP gas, check all steps in
the Installation Instructions.
BURNER CONTROL
KNOB WILL NOT TURN
• When the knob is at the OFF position, it must be pushed in before it can be
turned, and it can only be turned in a counterclockwise direction. When the
knob is at any other position, it can be turned in either direction without being
pushed in.
FAN DOES
NOT WORK
• The vent must be fully extended before fan will work.
• Fan control knob must be turned in clockwise direction to turn fan on.
If you need more help…call toll free:
GE Answer Center®
800.626.2000
consumer information service
26
We’ll Be There
With the purchase of your new GE appliance, receive the assurance that if you ever need
information or assistance from GE, we’ll be there. All you have to do is call—toll-free!
GE Answer Center®
800.626.2000
Whatever your question about any GE major appliance, GE Answer Center®
information service is available to help. Your call—and your question—will be
answered promptly and courteously. And you can call any time. GE Answer
Center® service is open 24 hours a day, 7 days a week.
In-Home Repair Service
800-GE-CARES (800-432-2737)
A GE consumer service professional will provide expert repair service,
scheduled at a time that’s convenient for you. Many GE Consumer Service
company-operated locations offer you service today or tomorrow, or at your
convenience (7:00 a.m. to 7:00 p.m. weekdays, 9:00 a.m. to 2:00 p.m. Saturdays).
Our factory-trained technicians know your appliance inside and out—so most
repairs can be handled in just one visit.
For Customers With Special Needs…
2’ 6"
TBXTOLITE
ON WALL
SINGLE CONTROL
FAUCET
800.626.2000
6’ 10"
8"
5"
6"
5"
7"
1’ 0"
GE offers, free of charge, a
brochure to assist in planning a
barrier-free kitchen for persons
with limited mobility.
Consumers with impaired hearing or speech who have
access to a TDD or a conventional teletypewriter may
call 800-TDD-GEAC (800-833-4322) to request
information or service.
1/8
3’ "
FLUORESCENT
FIXTURE
THIS LIGHT CAN
BE INSTALLED
IN BOTTOM OF
WALL CABINETS
2’ 10"
SECTION A-A
R SHALLOW DEPTH SINKS (6") WITH REAR DRAIN.
SINK SHOULD ALSO BE UNDERCOATED
SCALE 1’ 1"
=
Service Contracts
800-626-2224
You can have the secure feeling that GE Consumer Service will still be there
after your warranty expires. Purchase a GE contract while your warranty is still
in effect and you’ll receive a substantial discount. With a multiple-year contract,
you’re assured of future service at today’s prices.
Parts and Accessories
800-626-2002
Individuals qualified to service their own appliances
can have parts or accessories sent directly to their home.
The GE parts system provides access to over 47,000
parts…and all GE Genuine Renewal Parts are fully
warranted. VISA, MasterCard and Discover cards
are accepted.
User maintenance instructions contained in this guide
cover procedures intended to be performed by any user.
Other servicing generally should be referred to qualified
service personnel. Caution must be exercised, since
improper servicing may cause unsafe operation.
27
Staple sales slip or cancelled check
here. Proof of original purchase date
is needed to obtain service
under warranty.
YOUR GE COOKTOP
WARRANTY
FULL ONE-YEAR WARRANTY
For one year from date of original
purchase, we will provide, free of
charge, parts and service labor in
your home to repair or replace
any part of the cooktop that fails
because of a manufacturing
defect.
This warranty is extended to
WHAT IS COVERED
the original purchaser and any
succeeding owner for products
purchased for ordinary home use
in the 48 mainland states, Hawaii
and Washington, D.C. In Alaska the
warranty is the same except that it
is LIMITED because you must pay
to ship the product to the service
shop or for the service technician’s
travel costs to your home.
All warranty service will be
provided by our Factory Service
Centers or by our authorized
Customer Care® servicers during
normal working hours.
Should your appliance need
service, during warranty period or
beyond, call 800-GE-CARES
(800-432-2737).
• Service trips to your home to teach • Replacement of house fuses or
WHAT IS NOT COVERED
you how to use the product.
resetting of circuit breakers.
Read your Use and Care material.
If you then have any questions
about operating the product,
• Failure of the product if it is used
for other than its intended purpose
or used commercially.
please contact your dealer or our
Consumer Affairs office at the
address below, or call, toll free:
GE Answer Center®
800.626.2000
consumer information service
• Damage to product caused
by accident, fire, floods or acts
of God.
WARRANTOR IS NOT
RESPONSIBLE FOR
CONSEQUENTIAL DAMAGES.
• Improper installation.
If you have an installation problem,
contact your dealer or installer.
You are responsible for providing
adequate electrical, gas, exhausting
and other connecting facilities as
described in the Installation
Instructions provided with the
product.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
To know what your legal rights are in your state, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company
If further help is needed concerning this warranty, write:
Manager—Consumer Affairs, GE Appliances, Louisville, KY 40225
JGP645
Part No. 183D5580P039
Pub No. 49-8837
4-97 CG
Printed in Mexico
|