TECH SUPPORT
Datavideo offices worldwide to support this and other Datavideo products.
Datavideo Corporation (USA)
12300-U East Washington Blvd., Whittier, CA 90606 USA
Tel: +1 562 696 2324
Datavideo Technologies Europe BV
Californiedreef 263565 BL Utrecht, The Netherlands
Tel: +31 30 261 9656
Datavideo UK Limited
Unit 2 Waterside Business Park, Hadfield, Glossop, Derbyshire SK131BE UK
Datavideo Technologies Co., Ltd.
10F, 176 Jian-Yi Rd, Chung Ho City, Taipei Hsien, Taiwan 235
Tel: +886 2 8227 2888
Datavideo Technologies China Co.
2F-D, 2 Lane 777, West Guangzhong Rd, Zhabei District, Shanghai, China
Tel: +86 21 5603 6599
Datavideo Technologies (S) PTE Ltd.
100 Lor 23, Geylang Rd, #01-03 D’Centennial, Singapore 388398
Tel: +65 6749 6866
WHAT’S IN THE BOX?
1. AC / DC Switching Power Adaptor * 1
2. AC Cord * 1
4. 1.8M IEEE 1394 Firewire 6 to 4 Cable * 1
5. 1.8M IEEE 1394 Firewire 6 to 6 Cable *1
6. 1.2M BNC to BNC 75 Ohm Video cable *1
7. Stereo Audio RCA 2 to 2 Cable *1
8. Sun shade and Screws
9. Instruction Guide * 1
2
GENERAL:
Datavideo TLM-70D is a 7” TFT LCD monitors, selectable DV/CV input video source and
NTSC/PAL video format auto recognition with video pass through 75-ohm self-terminated
video output connector. The "AUX" input provides options for an external SDI to RGB video
format converters. The tilt hinges let you tilt the screen +/- 90 degree with contrast, brightness,
color and tint (Tint only available for NTSC) controls for a best view quality of display.
SPECIFICATIONS:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
LCD Display
7" TFT LCD active matrix, resolution 1440 x 234 dots
4:3 and 16:9 selectable
Aspect Ratio
Brightness (Luminance) 500 cd/mt
Contrast Ratio
300
View Angle
Top:
40 deg
Bottom: 60 deg
Left: 60 deg
Right: 60 deg
ꢀ
Video Input
CV input 1.0Vp-p, with self Loop-through output 75
Ohm-terminated
DV Input, support DV25 NTSC 4:1:1, PAL 4:2:0
Additional analog RGB Input for SDI format converter
NTSC/PAL auto recognition
ꢀ
ꢀ
ꢀ
Video System
Color Adjustment
Audio Input
Brightness, Contrast, Color, Tint
Stereo Audio Input RCA x 2
Embedded DV Audio input
ꢀ
Audio Output
Stereo Audio Bypass Output RCA x 2
Detachable Stereo Audio Speaker L/R
Three-Way Tally LED indicators
ꢀ
ꢀ
ꢀ
ꢀ
Tally Indication
Operation condition
Power Consumption
Operation temperature from 0ഒ to 50ഒ, RH less than 90%
DC12Volt, 2A
Dimension of LCD Panel 7.5” x 5.5” x 2.5” (W x H x D)
3
FRONT PANEL
3 Color Tally LED
Red, Green, Yellow
Select Composite
Video input
Power Switcher
Audio output Volume
Adjustment
Select DV input
Ear Phone output
There are two groups of function’s operation on this button:
Function 1: Click on the button to select three display aspects of 4:3, 16:9 or 16:9 aspect
with different horizontal timing scaling.
Function 2: Push and hold on the button 2 seconds to select display effects;
Release the button to enable the selected effect accordingly.
1). Push and hold on the button 2 seconds to select “Mirror” effect.
2). Keep holding for another 2 seconds to flip the video “Up Side Down”.
3). Keep holding for another 2 seconds to back to normal display mode.
4
REAR PANEL
9
8
10
6
7
5
4
1
2
3
1. DV Input: Support DV25, NTSC 4:1:1, PAL: 4:2:0
2. DV Loopthru Output
3. CV and Stereo Audio Input.
4. Video/ Bypass Output and Audio Line out
5. DC power input: 12V, 2.0Amp
6. Color adjustments: Brigtness, Contrast, Color, Tint for CV input, DV input can adjust
only the Brightness
7. Stereo Audio Speaker Output L/R
8. Tally LED Control Input (D-Sub 15-Pin): D-Sub 15 pins connector on the rear panel.
It works by closing contacts between a ground pin and the corresponding LED pin as
following pin out table. Do not give power to the pins.
LED
Red
Green
Yellow
Pin 1-4 short 2-4 short 3-4 short
5
9. AUX Video Input (D-Sub 9-Pin):
An additional video input terminal with RGB and Sync input interface. Connect the
Pin 7 to Ground (Short the Pin 7 & 8) to activate this interface and turn on the 12VDC
power output on Pin 1 & 6.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
PIN 1:
PIN 2:
PIN 3:
PIN 4:
PIN 5:
PIN 6:
PIN 7:
PIN 8:
PIN 9:
12VDC 300mA output
Video “R”Input
Video “G”Input
Video “CV_Sync”Input
Video “B”Input
12VDC 300mA output
SDI Switch (Connect to Ground to enable RGB Input of Pin 2-5)
Ground
Ground
10.DIP Switch setting for DV Input mode select
Please refer to the setting below for proper operation. (See Note 1 below)
ꢀ
ꢀ
ꢀ
ꢀ
S1. PAL or NTSC (PAL-ON, NTSC-OFF)
S2. NTSC setup level 7.5 IRE / 0 IRE (ON: 0 IRE, OFF: 7.5 IRE). (See Note 2 below)
S3. Locked Audio (OFF: Locked Audio, ON: Unlocked Audio, factory default)
S4 & S5 setting for different PC Operation System
ON
MAC OS (See Note 3 below)
S5
S5
ON S4
OFF Windows 2000 and Windows 98
ON Windows XP and Windows ME
OFF DV Camera mode
OFF S4
ꢀ
S6. Factory setting (OFF), please do not change.
*. Note 1: Reboot TLM-70D if you change a DIP Switch
Turn-on TLM-70D before launching any NLE software
*. Note 2: NTSC 0 IRE is most often used in Japan
NTSC 7.5 IRE is used elsewhere
*. PAL Video is always at 0 IRE mode
*. Note 3: To work with a DV source from MAC with Final Cut Pro:
1). Select "Preferences" from Final Cut Pro menu
2). Select "General" page
3). Uncheck "Abort capture on dropped frame"
4). Uncheck "Abort capture on time code break" for Final cut pro
5). Click OK button
6
LCD Sunshade Installation
Two Sunshade screws
Sunshade sheet
Step-1. Remove two screw covers on LCD panel
Step-2 Pun on Sunshade cover and locate two screw holes position
7
Step-3 Fasten two Sunshade screws
Step-4 Correctly installed LCD Sunshade
8
APPLICATION EXAMPLE
(TLM-70D Mounting on Wall)
Additional accessories --- BH-05
The application to install TLM-70D
on a DV Cam by using BH-05
(TLM-70D on DV Cam)
9
All the trademarks are the properties of their respective owners.
Datavideo Technologies Co., Ltd. All rights reserved 2004.
P/N: 082060354E2
10
|