OWNER’S
MANUAL
EMERSON AND THE G-CLEF LOGO ARE REGISTERED
TRADEMARKS OF EMERSON RADIO CORP., PARSIPPANY,
NEW JERSEY, U.S.A.
DVD PLAYER with VIDEO CASSETTE RECORDER
CEDV800D
ReWritable
Recordable
POWER
OPEN/CLOSE
STOP/EJECT
OUTPUT
CHANNEL
VIDEO
L
AUDIO
R
PLAY
DVD
VCR
DVD
VCR TIMER REC
REC
STOP
PLAY
REW
F.FWD
NOTE: You cannot copy a DVD to a video tape, as it is against copyright recording rules.
If you need additional assistance for set-up or operating
after reading owner’s manual, please call
-
-
TOLL FREE : 1 800 287-4871.
Please read before using this equipment.
IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instruc-
ing of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection
to grounding electrodes, and requirements for the grounding
electrode. (Fig. A)
tions should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
FIGURE A
ANTENNA
LEAD
EXAMPLE OF ANTENNA GROUNDING
WIRE
AS PER NATIONAL ELECTRICAL CODE
GROUND
CLAMP
5. Cleaning - Unplug this video product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol clean-
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ers.
Use
a
damp
cloth
for
cleaning.
EXCEPTION: A product that is meant for uninterrupted ser-
vice and, that for some specific reason, such as the possibil-
ity of the loss of an authorization code for a CATV convert-
er, is not intended to be unplugged by the user for cleaning
or any other purpose, may exclude the reference to unplug-
ging the appliance in the cleaning description otherwise
required in item 5.
6. Attachments - Do not use attachments not recommended by
the video product manufacturer as they may cause hazards.
7. Water and Moisture - Do not use this video product near
water, for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool,
and the like.
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
NEC – NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
14. Lightning - For added protection for this video product dur-
ing a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall out-
let and disconnect the antenna or cable system. This will pre-
vent damage to the video product due to lightning and
power-line surges.
15. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other elec-
tric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
8. Accessories - Do not place this video
product on an unstable cart, stand, tripod,
bracket, or table. The video product may
fall, causing serious injury to a child or
adult, and serious damage to the appli-
ance. Use only with a cart, stand, tripod,
bracket, or table recommended by the
16. Overloading - Do not overload wall outlets and extension
manufacturer, or sold with the video
cords as this can result in a risk of fire or electric shock.
product. Any mounting of the appliance should follow the
manufacturer's instructions and should use a mounting
accessory recommended by the manufacturer. An appliance
and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
17. Object and Liquid Entry - Never push objects of any kind
into this video product through any openings as they may
touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the video product.
18. Servicing - Do not attempt to service this video product
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19. Damage Requiring Service - Unplug this video product
from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
9. Ventilation - Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the video
product and to protect it from overheating, and these open-
ings must not be blocked or covered. The openings should
never be blocked by placing the video product on a bed,
sofa, rug, or other similar surface. This video product should
not be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the manufac-
turer's instructions have been adhered to.
10. Power Sources - This video product should be operated
only from the type of power source indicated on the mark-
ing label. If you are not sure of the type of power supply to
your home, consult your appliance dealer or local power
company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
11. Grounding or Polarization - This video product is
equipped with a polarized alternating-current line plug (a
plug having one blade wider than the other). This plug will
fit into the power outlet only one way. This is a safety fea-
ture. If you are unable to insert the plug fully into the outlet,
try reversing the plug. If the plug should still fail to fit, con-
tact your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the video product to its normal operation.
e. If the video product has been dropped or damaged in any
way.
f. When the video product exhibits a distinct change in perfor-
mance this indicates a need for service.
20. Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteris-
tics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
21. Safety Check - Upon completion of any service or repairs to
this video product, ask the service technician to perform
safety checks to determine that the video product is in prop-
er operating condition.
22. Heat - This video product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
13. Outdoor Antenna Grounding - If an outside antenna or
cable system is connected to the video product, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA
No. 70, provides information with regard to proper ground-
EN
–
–
3
1L25
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of all materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local
regulations concerning chemical wastes.
The serial number of this product may be found on the back of the DVD/VCR COMBINATION UNIT. This ser-
ial number is unique to your machine. You should record the number and other vital information here and retain
this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not
kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
ABOUT COPYRIGHT
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use
of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SUPPLIED ACCESSORIES
RF Cable
Remote control
Two AA batteries
A/V cables
(NA220UD)
(NA270UD)
(approx. 3 feet (100 cm)
long) (WPZ0102TM015)
WPZ0901TM002
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some headings and notes in this manual, with the following meanings
VCR
: Description refers to playback of video cassette tapes.
DVD-V
: Description refers to playback of DVD video discs.
CD
: Description refers to playback of audio CDs.
MP3
: Description refers to playback of MP3 discs.
QUICK
: Description refers to the items to be set in the QUICK mode.
EN
–
–
4
1L25
TABLE OF CONTENTS
ꢀ LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ꢀ PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
GENERAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DISC MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
STEP BY STEP PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 23
RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
FAST FORWARD / REVERSE SEARCH . . . . . . . . . . . . . . . 23
SLOW FORWARD / SLOW REVERSE . . . . . . . . . . . . . . . . 23
ZOOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TRACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TITLE / CHAPTER SEARCH. . . . . . . . . . . . . . . . . . . . . . . . 24
TIME SEARCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
PROGRAM (CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
RANDOM PLAYBACK (CD). . . . . . . . . . . . . . . . . . . . . . . . 26
MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
ON-SCREEN INFORMATION . . . . . . . . . . . . . . . . . . . . . . . 26
TRACK SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
RANDOM PLAYBACK (MP3). . . . . . . . . . . . . . . . . . . . . . . 27
PROGRAM (MP3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
STEREO SOUND MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CHANGING THE ON-SCREEN DISPLAY . . . . . . . . . . . . . 28
PARENTAL CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MARKER SETUP SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . 29
ꢀ DVD SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
AUDIO SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
BLACK LEVEL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . 30
VIRTUAL SURROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DISPLAY SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
LANGUAGE SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
ꢀ TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . . . . 32
ꢀ MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
ꢀ SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ꢀ IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . 3
ABOUT COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SYMBOLS USED IN THIS MANUAL. . . . . . . . . . . . . . . . . . 4
ꢀ FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ꢀ PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ꢀ ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PLAYABLE DISCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DISC TYPES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ꢀ OPERATING CONTROLS AND FUNCTIONS. . . . . . . . . . . 8
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DISPLAYS DURING OPERATION . . . . . . . . . . . . . . . . . . . 11
LOADING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . 11
ꢀ VCR/DVD SWITCHING . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ꢀ HOOKUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CONNECTING TO A TV WITHOUT A/V TERMINALS. . . 13
CONNECTING TO A TV WITH A/V TERMINALS. . . . . . . 13
CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT
JACK OR COMPONENT VIDEO IN JACKS. . . . . . . . . . . . 14
CONNECTING TO A STEREO AMPLIFIER EQUIPPED
WITH DIGITAL INPUT JACKS SUCH AS MD DECK OR
DAT DECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CONNECTING TO A RECEIVER WITH
DOLBY DIGITAL DECODER . . . . . . . . . . . . . . . . . . . . . . . 15
CONNECTING TO AN ANALOG AUDIO SYSTEM. . . . . . 15
ꢀ SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
AUTOMATIC CHANNEL SET UP. . . . . . . . . . . . . . . . . . . . 16
TO CHANGE THE ON-SCREEN LANGUAGE. . . . . . . . . . 17
CLOCK SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ꢀ PLAYBACK FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 18
SEARCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ꢀ RECORDING FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 19
NORMAL RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
OTR (One Touch Recording). . . . . . . . . . . . . . . . . . . . . . . . . 19
TIMER RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
HINTS FOR TIMER RECORDING . . . . . . . . . . . . . . . . . . . 20
ꢀ SPECIAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
COPYING A VIDEO TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . 21
MTS (Multi-Channel Television Sound) SYSTEM . . . . . . . . 21
AUTO REWIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
REAL TIME TAPE COUNTER. . . . . . . . . . . . . . . . . . . . . . . 22
EN
–
–
5
1L25
FEATURES
¡Virtual Surround Sound
DVD
Mode
¡Component Video Out Jacks
¡Dolby Digital sound
This DVD/VCR COMBINATION UNIT can output a
Dolby Digital audio signal.
Jacks located on the back of the DVD/VCR COMBINA-
TION UNIT which are used to send high-quality video to
a TV via Component Video In Jacks.
¡Still/fast/slow/step playback
¡Bit rate indication
¡Random playback for audio CD and MP3
¡Program playback for audio CD and MP3
¡DVD menus in a desired language
¡DRC (Dynamic range control)
You can control the range of sound volume.
¡Black Level Setting
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no input
from the player for five minutes in the stop mode. When
the screen saver program is activated for 30 minutes, the
power automatically turns off.
VCR
Mode
Hardware specifications
¡Auto Head Cleaner
¡4 Head HiFi Stereo
¡Subtitles in a desired language
¡Selecting a camera angle
¡Trilingual on-screen menu display selectable in
English, French, or Spanish
¡Choices for audio language and sound mode
¡Parental lock
¡181 channel capability PLL frequency synthesiz-
er tuner with direct station call
(A cable converter box may be necessary to view scram-
bled cable channels.)
¡Automatic detection of discs
This player automatically detects if the loaded disc is
DVD, audio CD or MP3 on disc.
Automatic functions
¡Playback MP3 disc
¡Auto power on system
Automatically turns the VCR on when you insert the cas-
sette.
¡Direct Search
¡On-screen display
¡Digital Auto Tracking (DTR)
Information about the current operation can be displayed
on the TV screen, allowing you to confirm the currently
active functions (such as program playback), on the TV
screen using the remote control.
Playback
¡Auto Repeat
¡2 Step Picture Search Operation
¡Index Search
¡Search
Chapter search / Title search / Track search / Time search
¡Time Search
¡Repeat
Chapter / Title / Track / Group / All / A-B
Recording
¡Zoom
¡1Year, 8 events (including Daily and WeeklyTimer
Recording)
¡Marker
The part designated by user can be called back.
¡OTR (One Touch Recording)
¡Resume Play
PRECAUTIONS
AVOID THE HAZARDS OF
INSTALLATION LOCATION
ELECTRICAL SHOCK AND FIRE
For safety and optimum performance of your
DVD/VCR COMBINATION UNIT:
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it
from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on your DVD/VCR
COMBINATION UNIT, unplug the power cord imme-
diately and take the unit to our Authorized Service
Center for servicing.
• Install the DVD/VCR COMBINATION UNIT in a hor-
izontal and stable position. Do not place anything
directly on top of the DVD/VCR COMBINATION
UNIT. Do not place the DVD/VCR COMBINATION
UNIT directly on top of the TV.
• Shield it from direct sunlight and keep it away from
sources of intense heat. Avoid dusty or humid
places. Avoid places with insufficient ventilation for
proper heat dissipation. Do not block the ventilation
holes on the sides of the DVD/VCR COMBINATION
UNIT. Avoid locations subject to strong vibration or
strong magnetic fields.
• Do not put your fingers or objects into the DVD/VCR
COMBINATION UNIT cassette holder.
MOISTURE CONDENSATION WARNING
Moisture condensation may occur inside the unit when
it is moved from a cold place to a warm place, or after
heating a cold room or under conditions of high
humidity. Do not use the DVD/VCR COMBINATION
UNIT at least for 2 hours until its inside is dry.
EN
–
–
6
1L25
ABOUT THE DISCS
PLAYABLE DISCS
DISC TYPES
The following discs can be played back on this
DVD/VCR COMBINATION UNIT.
[
]
DVD
Data on a DVD is divided into sections called "titles", and
then into subsections called "chapters", each of which is
given a title or chapter number. Playback conditions are
preset on some DVD video discs, and these playback con-
ditions take priority over user operations on this player. If
a function you selected does not run as desired, refer to
the manual accompanying the disc.
¡
¡
¡
¡
¡
¡
DVD video
DVD+R/RW*
CD-R/RW*
DVD-R/RW*
Audio CD
MP3*
* Depending on the types or the writing method of the
medium some discs can not be played.
Example
• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs
made on personal computers, or on DVD recorders may
not be played back properly due to factors such as
scratches, dirt or special properties of the disc.
Title 1
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
• Discs made on personal computers may not be played
back properly due to different environments or the set-
tings of the application you use. We recommend always
to use the standardized, properly formatted discs.
(Please contact the sales agency for more detail).
[
]
AUDIO CD
This player conforms to the NTSC color system. You can-
not play discs recorded in other color systems such as
PAL or SECAM.
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
¡Some discs include region codes as shown below.
Example
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
¡The number inside the symbol refers to a region of the
world, and a disc encoded in a specific region format
can only be played back on DVD/VCR COMBINA-
TION UNIT with the same region code.
The following discs cannot be played back on this
DVD/VCR COMBINATION UNIT.
[
]
MP3
Data on an MP3 is divided into sections called "groups",
and then into subsections called "tracks", each of which is
given a group or track number.
¡
¡
¡
DVD with region codes other than 1 or ALL.
DVD-ROM
Example
Group 1
Group 2
DVD-RAM (Never play back, otherwise malfunc-
tion may result.)
Track 1
Track 2
Track 3
Track 4
Track 1
Track 2
¡
¡
¡
¡
¡
CD-ROM
VSD
CDV (Only plays back the audio part.)
CD-G (Only plays back the sound.)
CD-I (Never play back, otherwise malfunction
may result.)
¡
¡
SACD
Photo CD (Never play back, otherwise malfunc-
tion may result.)
Any other discs without compatibility indications.
EN
–
–
7
1L25
OPERATING CONTROLS AND FUNCTIONS
FRONT PANEL
1
2
3
4 5
6
7 8
POWER
OPEN/CLOSE
STOP/EJECT
PLAY
OUTPUT
CHANNEL
VIDEO
L
AUDIO
R
DVD
VCR
DVD
VCR TIMER REC
REC
STOP
PLAY
REW
F.FWD
22
20
18
16 14
17 15
10
12
21
19
13
11
9
REMOTE CONTROL
7. POWER Light
This light appears when the power is on.
8. STOP/EJECT Button (VCR)
EJECT Button
52
23
POWER SPEED AUDIO
24
Press to remove the tape from the VCR.
STOP Button
1
4
7
2
5
8
0
3
51
49
SKIP/CH.
Press to stop the tape motion.
9. PLAY Button(VCR) [page 18]
Press to begin playback.
6
25
VCR/TV
SLOW
9
50
10. CHANNEL Buttons [page 16]
+
10
In VCR mode, press to change TV channels on the
VCR; press to adjust the tracking during normal or slow
motion playback; press to remove vertical jitter in a Still
picture.
DISPLAY DVD
VCR
PAUSE
48
46
26
28
30
47
45
27
29
PLAY
STOP
11. AUDIO In Jacks [page 21]
Connect audio cables coming from the audio out jacks
of a camcorder, another VCR, or an audio source here.
12. VIDEO In Jack [page 21]
RECORD
MENU
44
42
Connect a video cable coming from the video out jack
of a camcorder, another VCR, or a video source (laser
disc player, camcorder, etc.) here.
31
33
35
ENTER
43
32
34
SETUP
TITLE
RETURN
SEARCH
MODE
CLEAR/
13. F.FWD Button (VCR) [page 18]
Press to rapidly advance the tape, or view the picture
rapidly in forward during playback. (Forward Search).
14. REW Button (VCR) [page 18]
MODE ZOOM
C.RESET
41
39
40
38
SUBTITLE ANGLE REPEAT
A
B
36
T-SET
37
Press to rewind the tape, or to view the picture rapidly
in reverse during the playback mode (Rewind Search).
15. REC/OTR Button [page 19]
1. Disc loading tray
2. OPEN/CLOSE Button [page 22]
Press once to start a recording. Press repeatedly to start
a One-Touch Recording.
Press to insert discs into or remove them from the tray.
3. DVD OUTPUT Light (Green) [page 12]
16. REC Light [page 19]
This light appears when the DVD output mode is select-
Lights up during recording.
ed. You can only watch DVDs when the green DVD 17. TIMER REC Light [page 20]
OUTPUT light is on. To make the green DVD OUT-
PUT light come on, press DVD on the remote control or
OUTPUT on the front panel.
This light appears when the DVD/VCR is in standby
mode for a timer recording or during a One-Touch
Recording. It flashes if T-SET is pressed for a timer
recording, but there is no tape in the DVD/VCR. It
flashes when all timer recordings or One-Touch
Recordings are finished.
4. VCR OUTPUT Light (Green) [page 12]
This light appears when the VCR output mode is select-
ed. You can only watch tapes when the green VCR
OUTPUT light is on. To make the green VCR OUTPUT
light come on, VCR on the remote control or OUTPUT
on the front panel.
5. CASSETTE COMPARTMENT
6. POWER Button [page 16]
Press to turn the power on and off.
EN
–
8 –
1L25
18. OUTPUT Button [page 12]
32. TITLE Button [page 23]
Press to select DVD mode or VCR mode.
GYou can switch the output mode either by pressing
33. SETUP Button [pages 28-31]
Press to enter DVD player setup mode.
OUTPUT on the front panel, or by pressing DVD or 34. ZOOM Button [page 24]
VCR on the remote control. However, if you press
Enlarges part of a DVD-reproduced image.
OUTPUT on the front panel first, you need to re- 35. MODE Button [pages 26, 27, and 30]
select the corresponding mode by pressing DVD or
VCR on the remote control.
Activates program playback or random playback mode
when playing CDs or MP3. Sets Black level and virtual
surround.
19. Remote Sensor Window
20. Display
36. SUBTITLE Button [page 27]
Press to select the desired subtitle language.
36. T-SET Button [page 20]
21. PLAY Button (DVD) [page 22]
Press to begin playback.
22. STOP Button (DVD) [page 22]
Press to put the VCR into standby mode for a timer
recording.
Stops operation of the disc.
23. SPEED Button [page 19]
Press to select the VCR’s recording speed (SP or SLP)
24. POWER Button
37. ANGLE Button [page 27]
Press to change the camera angle to see the sequence
being played back from a different angle.
38. REPEAT Button [page 25]
Repeats playback of the current disc, title, chapter or
track.
Press to turn the power on and off.
25. Number Buttons
GDVD mode [page 24]
Press to select numbered items in a menu.
+10
Use this button to enter number 10 and above.
GVCR mode [page 16]
39. A-B REPEAT Button [page 25]
Repeats playback of a selected section.
40. SEARCH MODE Button
GDVD mode [page 24]
Press to select TV channels on the VCR.
To select channels, enter channel numbers as a two-
digit number for the quickest results. For example, to
select channel 6, press 0 then 6.
26. DISPLAY Button
Press to access or remove the Search display,
which allows you to go directly to a specific
Title/Chapter/Track/Time.
GVCR mode [page 18]
Press to perform a Time Search or an Index Search.
41. CLEAR/C.RESET Button
GDVD mode [pages 24, 25]
GDVD mode [page 28]
Press to access or remove the display screen during
DVD or Audio CD playback.
GVCR mode [page 21]
Press to access or remove the VCR’s on-screen status
display.
Press to reset the setting.
GVCR mode [page 18]
Press to reset the counter. Press to exit from the
MENU screen.
27. DVD Button [page 12]
42. RETURN Button [page 30]
Press to select DVD mode for the remote control.
GYou can switch the OUTPUT mode either by pressing
GDVD mode [page 22]
Returns to the previous operation.
OUTPUT on the front panel, or by pressing DVD or 43. Arrow Buttons
VCR on the remote control. However, if you press
OUTPUT on the front panel first, you need to re-
select the corresponding mode by pressing
DVD or VCR on the remote control.
Use when making settings while watching the display
on a TV screen.
GVCR mode [page 16]
p/o Buttons
28. h Button
Press to enter digits when setting program (For exam-
ple: setting clock or timer program). Press to select
the setting modes from the on screen menu.
B Button
GDVD mode [page 23]
Press to view the DVD picture in fast reverse motion.
Press PAUSE, then press this button to begin slow
motion playback. Press this button repeatedly to
change the reverse speed of slow motion.
GVCR mode [page 18]
When setting program (For example: setting clock or
timer program), press to determine your selection and
proceed to the next step you want to input. Press to
determine the setting modes from the on screen
menu. Press to add or delete channel numbers during
channel preset.
Press to rewind the tape, or to view the picture rapid-
ly in reverse during the playback mode (Rewind
Search).
29. STOP Button
s Button
GDVD mode
Press to cancel a setting of timer program. Press to
correct digits when setting program (For example:
setting clock or timer program). Press to add or delete
channel numbers during channel preset.
44. ENTER Button
Press to stop the disc motion.
GVCR mode
Press to stop the tape motion.
30. RECORD Button [page 19]
Press once to start a recording.
31. MENU Button
GDVD mode [page 22]
Press to accept a setting.
GDVD mode [page 23]
Press to display the menu of the Disc.
GVCR mode [page 17]
Press to access the VCR menu.
EN
–
–
9
1L25
49. SLOW Button [page 18]
During tape playback, press to view the video tape in
slow motion. Press again to resume normal playback.
This button does not affect DVD playback.
50. VCR/TV Button [page 19]
Use to select VCR or TV position.
GVCR Position
45. g Button
GDVD mode [page 23]
Press to fast forward the Disc. Press PAUSE, then
press this button to begin slow motion playback.
Press this button repeatedly to change the forward
speed of slow motion.
GVCR mode [page 18]
To view playback, to monitor video recordings or to
watch TV using the VCR tuner.
GTV Position
To watch TV or to view one program while recording
another.
Press to rapidly advance the tape, or view the picture
rapidly in forward during playback (Forward Search).
46. PLAY Button
GDVD mode
Press to begin playback.
51. SKIP/CH. Buttons
GVCR mode
GDVD mode
Press to begin playback.
Press to skip Chapters or Tracks.
GVCR mode
47. VCR Button [page 12]
Press to select VCR mode for the remote control.
GYou can switch the OUTPUT mode either by pressing
OUTPUT on the front panel, or by pressing DVD or
VCR on the remote control. However, if you press
OUTPUT on the front panel first, you need to re-
select the corresponding mode by pressing DVD or
VCR on the remote control.
Press to change TV channels on the VCR.
52. AUDIO Button [page 27]
Press to select a desired audio language or sound mode.
48. PAUSE Button
Notes
GDVD mode [page 22]
¡To use the remote control to operate the DVD/VCR
COMBINATION UNIT and its features, press DVD
on the remote control before pressing other DVD’s
operation buttons. Verify that the green DVD OUT-
PUT Light is on.
Press to pause Disc playback. Press repeatedly to
advance the DVD picture step by step (or one frame
at a time).
GVCR mode [page 19]
While recording, press to temporarily stop the record-
ing (pause). Press a second time to resume normal ¡To use the remote control to operate the VCR and its
recording. You can not pause
a
One-Touch
features, press VCR on the remote control before
pressing other VCR’s operation buttons. Verify that
the green VCR OUTPUT Light is on.
Recording. Or, press during tape playback to freeze
the picture. Press to advance the picture one frame at
a time during still mode.
REAR VIEW
53
54 55
56
57
DVD
DVD/VCR
VCR
AUDIO OUT AUDIO IN
S-VIDEO COMPONENT AUDIO
DIGITAL
AUDIO OUT
OUT
VIDEO OUT
OUT
ANT-IN
L
L
Y
Cb
Cr
L
R
R
COAXIAL
ANT-OUT
VIDEO OUT VIDEO IN
R
63
61
62
59
60
58
53. ANT-IN (Antenna In) Jack
56.AC Power Cord
Connect your antenna, Cable Box, or Satellite decoder
box.
Connect to a standard AC outlet to supply power to the
DVD/VCR COMBINATION UNIT.
DVD Playback only
54. DVD/VCR AUDIO OUT Jacks
Connect the supplied audio cables here and to the Audio
In jacks of a television or other audio equipment.
55. AUDIO IN Jacks
57. COMPONENT VIDEO OUT Jacks
Connect optional component video cables here and to
the component Video In jacks of a television.
58. COAXIAL Jack
Connect audio cables coming from the audio out jacks
of a camcorder, another VCR, or an audio source here.
Connect an optional coaxial digital audio cable here and
to the Coaxial Digital Audio In jack of a decoder or
audio receiver.
EN
–
–
10
1L25
59. DVD ANALOG AUDIO OUT Jacks
Connect the supplied audio cables here and to the Audio
In jacks of a television or other audio equipment (DVD
only).
62. DVD/VCR VIDEO OUT Jack
Connect the yellow video cable (supplied) here and to
the TV’s Video In jack.
63. ANT-OUT (Antenna Out) Jack
Use the supplied RF coaxial cable to connect this jack
to the ANTENNA IN Jack on your TV.
60. S-VIDEO OUT Jack
Connect an optional S-Video cable here and to the S-
Video In jack of a television. (DVD only)
61. VIDEO IN Jack
Caution: Do not touch the inner pins of the jacks on
the rear panel. Electrostatic discharge may cause
permanent damage to the player.
Connect a cable coming from the video out jack of a
camcorder, another VCR, or an audio-visual source
(laser disc player, video disc player, etc.) here.
DISPLAY
DISPLAYS DURING OPERATION
DVD
Lights up when a DVD
is inserted into the tray.
No disc inserted or playing
DVD menu
Stays on when the
Stays on when repeat
A-B repeat function
track function is on.
is on.
Tray open
Stays on when
Stays on when the
repeat chapter
repeat function is on.
function is on.
Tray closed
Stays on when
repeat title
function is on.
Loading the Disc
LOADING THE BATTERIES
1. Open the battery compartment
cover.
Lights up when the
Lights up when a
inserted disc comes
CD is inserted into
to a pause.
the tray.
Stays on when the inserted
disc is being played back.
Displays how long a current title
2. Insert two AA batteries, with each
one oriented correctly.
or track has been played back. When
a chapter or track has switched, the
number of the a title, chapter or
track is displayed.
3. Close the cover.
Notes
¡Do not mix alkaline and manganese batteries.
¡Do not mix old and new batteries.
EN
–
–
11
1L25
VCR/DVD SWITCHING
Because this product is a combination of a VCR and DVD player, you must first select
which component you wish to operate with the OUTPUT BUTTON.
VCR MODE
DVD MODE
Press VCR on the remote control.
(Verify that the VCR OUTPUT Light is lit.)
Press DVD on the remote control.
(Verify that the DVD OUTPUT Light is lit.)
Notes
¡Pressing only OUTPUT on the front panel does not switch the mode of the remote control. You always need
to select the correct mode on the remote control too.
POWER
OPEN/CLOSE
POWER SPEED AUDIO
STOP/EJECT
OUTPUT
CHANNEL
VIDEO
L
AUDIO
R
PLAY
DVD
VCR
STOP
PLAY
DVD
VCR TIMER REC
REC
REW
F.FWD
1
4
7
2
5
8
0
3
SKIP/CH.
6
VCR/TV
SLOW
9
+
10
DVD button
DVD OUTPUT Light
DISPLAY DVD
VCR
PAUSE
VCR button
OUTPUT
PLAY
STOP
DVD
VCR TIM
RECORD
MENU
VCR OUTPUT Light
ENTER
SETUP
TITLE
RETURN
SEARCH
MODE
CLEAR/
MODE ZOOM
C.RESET
OUTPUT button
SUBTITLE ANGLE REPEAT
A
B
T-SET
EN
–
–
12
1L25
HOOKUPS
CAUTION:
¡Be sure to turn off the DVD/VCR COMBINATION UNIT and equipment to be connected.
¡Read through the operation manual for the equipment to be connected.
¡Be sure that the colors of the jacks and plugs match up when using VIDEO/AUDIO cables.
¡Be sure to keep the DVD/VCR COMBINATION UNIT connection cables separate from the TV antenna cable
when you install the DVD/VCR COMBINATION UNIT, because it may cause electrical interference when you
are watching television programs.
CONNECTING TO A TV WITHOUT A/V TERMINALS
1. Disconnect the AC power cord of the TV from the
[VHF/UHF
[Back of the DVD/VCR]
[Indoor antenna]
AC outlet.
combination antenna]
[Back of the
UHF/VHF combination TV]
2. Disconnect the antenna or cable from the TV.
3. Connect the antenna or cable to the ANT-IN jack of
the DVD/VCR COMBINATION UNIT.
4. Connect the DVD/VCR COMBINATION UNIT to
the TV using the RF cable.
5. Plug the AC power cords of the DVD/VCR COM-
BINATION UNIT and TV into the AC outlets.
RF cable
(supplied)
DVD/VCR
VCR
OR
OR
AUDIO OUT AUDIO IN
ANT-IN
L
L
UHF/VHF
[Cable box or satellite box]
R
R
IN
ANT-OUT
VIDEO OUT VIDEO IN
OUT
From Cable or
Satellite Company
RF OUTPUT CHANNEL for DVD/VCR
1. Connect the DVD/VCR COMBINATION UNIT to a TV using RF cable (see above steps).
2. Select channel 3 on your TV.
3. Press PLAY.
¡If noise appears, change the RF output channel of the DVD/VCR COMBINATION UNIT to channel 4 by
pressing PLAY on the VCR for 3 seconds during playback.
¡
There is case that the RF output channel does not change by situation (For example, when you adjust tracking using
(
)
CHANNEL
).
In this case, stop the playback, and start the playback again. After that, press PLAY on the VCR for 3 seconds.
If there is a power failure or the DVD/VCR COMBINATION UNIT is unplugged for more than 30 seconds, the RF
¡
output channel setting will return to CH3
.
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro-
vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected
to the grounding system of the building, as close to the point of cable entry as practical.
CONNECTING TO A TV WITH A/V TERMINALS
DVD
DVD/VCR
VCR
AUDIO OUT AUDIO IN
S-VIDEO COMPONENT AUDIO
DIGITAL
OUT
VIDEO OUT
OUT
AUDIO OUT
Antenna/Cable signal
ANT-IN
L
L
Y
R
Cb
Cr
L
A/V-compatible or
wide screen TV
COAXIAL
ANT-OUT
VIDEO OUT VIDEO IN
R
To ANT. IN
of TV
To VIDEO INPUT jack
To Right (red) and Left (white)
To AUDIO INPUT jacks
To VIDEO OUT jack
[Fig. 1]
To AUDIO OUT jacks
Notes
¡Connect the DVD/VCR COMBINATION UNIT directly to a TV. If the A/V cables are connected into a
VCR first, picture may be distorted due to the copy protection system.
EN
–
–
13
1L25
CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT JACK OR
COMPONENT VIDEO IN JACKS
FOR TVs WITH S-VIDEO INPUT JACK
Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pic-
tures.
The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBINATION
UNIT. Therefore, in order to use the VCR features or view TV channels on the DVD/VCR COMBINATION
UNIT, you still need to either connect the RF cable between the ANT-OUT jack of the DVD/VCR COMBINA-
TION UNIT and the TV’s Antenna In jack, or connect the yellow video cable as described earlier (Fig.1). To
connect the supplied RF cable, see page 13.
DVD
DVD/VCR
VCR
AUDIO OUT AUDIO IN
S-VIDEO COMPONENT AUDIO
DIGITAL
AUDIO OUT
OUT
VIDEO OUT
OUT
ANT-IN
L
L
Y
A/V-compatible or
wide screen TV
Cb
Cr
L
R
R
COAXIAL
ANT-OUT
VIDEO OUT VIDEO IN
R
To S-VIDEO INPUT jack
To S-VIDEO OUT jack
To Right (red) and Left (white)
To AUDIO INPUT jacks
[Fig. 2]
To AUDIO OUT jacks
FOR TVs WITH
COMPONENT VIDEO IN JACKS
Use a component video cable (commercially available) in place of the yellow DVD/VCR video cable and S-
VIDEO jack to enjoy higher quality pictures.
The component video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBI-
NATION UNIT. Therefore, in order to use the VCR features or view TV channels at the DVD/VCR COMBI-
NATION UNIT, you still need to either connect the RF coaxial cable between the ANT-OUT jack of the
DVD/VCR COMBINATION UNIT and the TV’s Antenna In jack, or connect the yellow VCR video cable as
described earlier (Fig. 1). To connect the supplied RF cable, see page 13.
To Right (red) and Left (white)
AUDIO OUTPUT jacks
To Right (red) and Left (white)
AUDIO INPUT jacks
A/V-compatible
or
wide screen TV
DVD
DVD/VCR
VCR
AUDIO OUT AUDIO IN
S-VIDEO COMPONENT AUDIO
DIGITAL
OUT
VIDEO OUT
OUT
AUDIO OUT
ANT-IN
L
L
Y
Cb
Cr
L
R
R
COAXIAL
ANT-OUT
VIDEO OUT VIDEO IN
R
To COMPONENT VIDEO
INPUT jacks
To COMPONENT VIDEO
OUT jacks
[Fig. 3]
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH
DIGITAL INPUT JACKS SUCH AS MD DECK OR DAT DECK
Use an audio coaxial digital cable (commercially available) for the audio connections.
Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
DVD
DVD/VCR
VCR
AUDIO OUT AUDIO IN
S-VIDEO COMPONENT AUDIO
DIGITAL
AUDIO OUT
(Stereo Receiver)
Amplifier equipped with digital
input jacks, MD deck,
DAT deck, etc.
OUT
VIDEO OUT
OUT
ANT-IN
L
L
Y
Cb
Cr
L
R
R
COAXIAL
ANT-OUT
VIDEO OUT VIDEO IN
R
To COAXIAL DIGITAL
AUDIO OUT jack
[Fig. 4]
To COAXIAL DIGITAL AUDIO INPUT jack
Notes
¡The audio source on a disc in the 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
¡Set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a DVD disc using incorrect set-
tings may generate noise distortion, and may also damage the speakers. (See page 29 to set DOLBY DIGITAL
to OFF.)
EN
–
–
14
1L25
CONNECTING TO A RECEIVER WITH DOLBY DIGITAL DECODER
If using this DVD/VCR COMBINATION UNIT to play a DVD disc in 5.1 channel Dolby Digital surround, the
DVD/VCR COMBINATION UNIT outputs a Dolby Digital data stream from its COAXIAL DIGITAL AUDIO
OUT jack. By hooking the DVD/VCR COMBINATION UNIT up to a Dolby Digital receiver, you can enjoy a
more convincing, realistic ambience with powerful and high-quality surround sound as heard in movie theaters.
Use an audio coaxial digital cable (commercially available) for the audio connections.
DVD
DVD/VCR
VCR
AUDIO OUT AUDIO IN
S-VIDEO COMPONENT
DVD
DIGITAL
AUDIO OUT
OUT
VIDEO OUT AUDIO OUT
ANT-IN
L
L
Y
Cb
Cr
L
R
R
COAXIAL
ANT-OUT
VIDEO OUT VIDEO IN
R
Center speaker
Front speaker
(right)
Front speaker
(left)
To COAXIAL DIGITAL
AUDIO OUT jack
Receiver with
Dolby Digital Decoder
To COAXIAL DIGITAL
AUDIO INPUT jack
Subwoofer
Surround
speaker
(left)
Surround
speaker
(right)
[Fig. 5]
¡If the output is Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to ON for audio
output in the setup mode.
¡
Unless connected to a Dolby Digital receiver, set DOLBY DIGITAL to OFF for audio output in the setup mode.
Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers
.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
CONNECTING TO AN ANALOG AUDIO SYSTEM
DVD
DVD/VCR
VCR
AUDIO OUT AUDIO IN
S-VIDEO COMPONENT
DVD
DIGITAL
OUT
VIDEO OUT AUDIO OUT
AUDIO OUT
To AUDIO OUT jacks
ANT-IN
L
Y
R
Cb
Cr
COAXIAL
ANT-OUT
VIDEO OUT VIDEO IN
Stereo system
To Right (red) and Left (white)
AUDIO INPUT jacks
or
To ANALOG AUDIO INPUT jacks
To Right (red) and Left (white)
ANALOG AUDIO OUT jacks
[Fig. 6]
Notes
¡Be sure to turn off the power to all components in the system before connecting another component.
¡Refer to the Owner's Manuals for stereo systems and any other components to be connected to the DVD/VCR
COMBINATION UNIT.
EN
–
–
15
1L25
SETUP
AUTOMATIC CHANNEL SET UP
6
After scanning, the tuner stops on the low-
est memorized channel. The TV screen
returns to TV mode.
VCR
You can automatically program the tuner to scan only
the channels you receive in your area.
¡If “AUTO SET UP” appears on the TV screen again,
check the cable connections. Press B once again and
the VCR will begin preset again.
¡Channel memory programming is NOT needed
when you connect the VCR to a cable box or a satel-
lite box as in "CONNECTING TO A TV WITHOUT
A/V TERMINALS" on page 13. In this case, select
channel 3 on your TV. Then, the channel you want to
record or view may be selected at the cable box or
satellite box.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same chan-
nel (CH4) on your TV.
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using CHAN-
NEL (o/p) or by directly pressing Number on the
remote control.
Note for using the Number:
¡When selecting cable channels which are higher
than 99, enter channel numbers as a three-digit num-
ber.(For example: 117, press 1,1,7)
¡You must precede single-digit channel numbers with
a zero (For example: 02, 03, 04 and so on).
¡Follow the steps below once. Repeat only if there
is a power failure or if the VCR is unplugged for
more than 30 seconds. (In these cases, the pro-
grammed channels are erased.)
¡You must follow the steps below before attempting
to play or record a video tape. If you want to play
or record a video tape BEFORE programming the
tuner, you can cancel it by pressing
TO PRESET THE CHANNELS AGAIN
1
Press MENU until the main menu appears.
(If you have already set the clock, you only
have to press it once. If not, you have to
press it twice).
CLEAR/C.RESET.
1
You need to connect the antenna or cable to
the VCR first. Then, connect the DVD /VCR
power plug to a standard AC outlet.
2
3
Select “CHANNEL SET UP” by pressing
or L. Then, press B.
K
2
Turn on the TV and set the TV to channel 3.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same chan-
nel (CH4) on your TV. (See “RF OUTPUT
CHANNEL” on page 13 for the detail.)
Select “AUTO SET UP” by pressing K or L.
Then, press B.
¡After scanning, the tuner stops on the lowest memo-
rized channel.
3
4
Turn on the VCR by pressing POWER. the
POWER light will come on.
Select the On Screen Language (“ENG-
LISH”, “FRANÇAIS” or
“ESPAÑOL”) by pressing
K
or L. Then, press B.
5 Begin channel preset by pressing B once.
The tuner scans and memorizes all active
channels in your area.
CH 01
¡The VCR distinguishes between
standard TV channels and cable
channels.
AUTO SET UP
EN
–
–
16
1L25
TO ADD/DELETE CHANNELS
CLOCK SET UP
When scanning, some channels may be skipped due to
a weak signal. In such cases, you can add the channels
to the VCR memory manually.
VCR
1
Select main menu by pressing MENU.
1
Press MENU until the main menu appears.
¡If the clock is not set, the CLOCK SET menu
appears first. In this case, follow step [3].
(If you have already set the
- MENU -
TIMER PROGRAMMING
[OFF]
AUTO REPEAT
CHANNEL SET UP
CLOCK SET
clock, you only have to
press it once. If not you
have to press it twice).
LANGUAGE SELECT
AUDIO OUT
[ON]
TV STEREO
SAP
2
3
Select "CLOCK SET" by pressing K or L.
Then, press B.
Set the clock.
2
3
4
5
Select "CHANNEL SET UP" by pressing
K
or L. Then, press B.
1) Set the month
Select "MANUAL SET UP" by pressing K or
L. Then, press B.
Press K or L repeatedly.
Then, press B.
Enter the desired channel number by press-
ing K or L.
2) Set the day
Press K or L repeatedly.
Then, press B.
Add or Delete it from memory by pressing
B or s so that "ADD" or "DELETE" flashes
on the TV screen accordingly.
3) Set the year
Press K or L repeatedly.
Then, press B.
The day of the week will appear automatically.
6
Exit the Preset mode by pressing
CLEAR/C.RESET.
4) Set the hour
Press K or L repeatedly.
Then, press B.
TO CHANGE THE ON-SCREEN
LANGUAGE
5) Set the minute
Press K or L repeatedly.
Then, press B.
VCR
1
Press MENU twice to call up the main
menu. (If you have already set the clock,
you only have to press it once).
6) Set AM or PM
CLOCK SET
MONTH DAY
YEAR
Press K or L repeatedly.
03 17 MON 2003
/
HOUR MINUTE AM/PM
05
:
40
PM AM
PM
2
3
Select "LANGUAGE SELECT" by pressing
or L. Then, press B.
K
¡To go back one step, press s.
Select "ENGLISH", "FRANCAIS" or
"ESPAÑOL" by pressing K or L. Then, press
CLEAR/C.RESET.
4
Start the clock by pressing
CLEAR/C.RESET or B.
¡If you accidentally select Spanish or French and
need English: Press MENU and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press B,
and select ENGLISH by pressing K or L.
Finally, press CLEAR/C.RESET.
EN
–
–
17
1L25
PLAYBACK FUNCTION
NORMAL PLAYBACK
2
3
Select "AUTO REPEAT" by pressing K or L.
VCR
Begin auto repeat playback by pressing
so that ON appears next to "AUTO
REPEAT".
B
1
Insert a prerecorded tape. The VCR will turn
on.
¡If the safety tab has been removed, the
VCR will start playback automatically.
¡
If the on-screen menu still remains, CLEAR/C.RESET
to exit the menu.
¡To cancel the Auto repeat mode, press B at step [3]
so that OFF appears next to "AUTO REPEAT".
2
Turn on the TV and set the TV to channel 3.
¡
If noise appears, change the RF output channel of the
VCR to channel 4 by pressing PLAY for 3 seconds dur-
ing playback. Then select the same channel (CH4) on
your TV. (See “RF OUTPUT CHANNEL” on page 13
for the detail.)
SEARCH FUNCTIONS
VCR
PICTURE SEARCH
3
Begin playback by pressing PLAY.
If you want to skip or repeat a scene during playback,
press D or E.
¡Tracking adjustment will be done automatically
(Digital Tracking function) when you start playback.
To adjust the tracking manually, press SKIP/CH. on
the remote or CHANNEL (o/p) on the VCR.
¡Press it again and the VCR will now search at super
high speed. (in the LP/SLP modes only).
INDEX SEARCH
¡When a tape has reached the end, the VCR will
rewind the tape to the beginning, and eject the tape.
An index mark will be assigned at the beginning of
each recording you made. You may skip to a specific
marked point by following the steps below.
4
To stop playback, press STOP.
¡If no corresponding symbols appear on the display
when you press buttons such as PLAY, RECORD,
D or E, that means no cassette tape is in the
VCR. Please insert a tape.
1
2
Press SEARCH MODE so that the Index
Search menu appears.
Enter the number of recordings you wish to
skip by pressing K or
L
INDEX SEARCH
03
Counter Reset
within 30 seconds.
¡You can reset the counter by pressing
CLEAR/C.RESET on the remote control twice.
STILL/SLOW
3
Press B or { to start index search.
You can freeze the picture on TV screen by pressing
PAUSE during playback.
¡If you want to go in the forward direction, press B.
¡If you want to go in the reverse direction, press {.
¡If you want to stop search function, press STOP.
¡After index search, the VCR will play the tape auto-
matically.
¡You can advance the picture one frame at a time by
pressing PAUSE during the Still mode.
¡You cannot manually adjust the tracking of a still
picture. However, if the picture begins to vibrate
vertically during the still mode, you can stabilize the
picture by pressing CHANNEL (o/p).
TIME SEARCH
This feature allows you to go to a specific point on a
tape by entering the exact amount of time you wish to
skip in order to reach the point.
¡If the picture is distorted or rolling vertically, adjust
the vertical hold control on your TV, if so equipped.
¡You can watch in the slow motion by pressing
SLOW during playback or the still mode.
¡If a noise bar appears on the TV screen, you can
reduce it by pressing CHANNEL (o/p).
¡After the VCR has been in Still/Slow mode for 5
minutes, it will stop automatically to protect the tape
and the video head from damage.
1
2
Press SEARCH-MODE so that the Time
Search menu appears.
TIME SEARCH
2 : 50
Enter your desired time to
skip by pressing K or
L
within 30 seconds.
¡To return to playback, press PLAY.
AUTO REPEAT PLAYBACK
3
Press B or { to start time search.
¡If you want to go in the forward direction, press B.
¡If you want to go in the reverse direction, press {.
¡If you want to stop search function, press STOP.
¡After time search, the VCR will play the tape auto-
matically.
VCR
This feature allows you to play a tape over and over.
1
Select main menu by pressing MENU.
EN
–
–
18
1L25
RECORDING FUNCTION
VCR
OTR (One Touch Recording)
You can not copy a DVD to a videotape.
VCR
It may be UNLAWFUL to record copyrighted materi-
al without the consent of the copyright owner.
Accidental Erasure Prevention
This feature allows you to set the recording length sim-
ply by pressing REC/OTR on the VCR.
To prevent accidental recording on a
recorded cassette, remove its record
safety tab. To record on it later, cover
the hole with cellophane tape.
1
Press REC/OTR to begin OTR. The TIMER
REC light comes on. Change the recording
length by pressing REC/OTR repeatedly.
Record safety tab
Before recording, make sure:
REC
OTR(0:30)
OTR(1:00).....
¡The desired channel is selected by pressing Number
on the remote control or CHANNEL (o/p). (If you
connected the VCR to a cable box or satellite box as
in "CONNECTING TO A TV WITHOUT A/V TER-
MINALS" on page 13, select channel 3 on your TV,
and select the specific INPUT channel assigned by
your cable box or your satellite box on the
DVD/VCR COMBINATION UNIT. Then, select the
channel you want to record with the cable box or the
satellite box. In this case, you can ONLY record and
view the SAME channel.)
(Normal recording)
OTR(8:00)
OTR(7:30)
¡
If a tape ends during OTR, the VCR will stop, eject
the tape, and switch to the DVD mode automatically
as the TIMER REC light blinks. (If the DVD power
is off, the VCR will become STANDBY status)
.
¡When OTR is finished , the VCR turns off automat-
ically. To use the VCR again, press T-SET on the
remote, or STOP/EJECT on the DVD/VCR COM-
BINATION UNIT.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same chan-
nel (CH4) on your TV.
¡There is a tape with a safety tab in the VCR.
¡The desired recording speed is selected in SP (stan-
dard play) or SLP (super long play) mode by press-
ing SPEED on the remote control.
TIMER RECORDING
VCR
You may set the VCR to start recording while you are
away. You can set eight programs to record on specif-
ic days, daily or weekly within 1 year period.
Tape Speed
Recording/Playback Time
Type of tape
SP mode
SLP mode
T60
1 hour
3 hours
T120
2 hours
6 hours
T160
2-2/3 hours
8 hours
If you have not yet set the clock, "CLOCK SET"
appears. If so, follow the steps [3] and [4] in
"CLOCK SET UP" section on page 17. Then, set
the timer recording.
Note
¡You can not copy a DVD to a videotape.
1
Insert a tape with its safety tab into the
DVD/VCR COMBINATION UNIT.
NORMAL RECORDING
2
3
Select main menu by pressing MENU.
VCR
TIMER PROGRAMMING
Select "TIMER PROGRAM-
MING" by pressing K or L.
Then, press B. The set up
screen is displayed.
1
Begin the recording by pressing RECORD.
The REC Light comes on.
PROG
DATE
12345678
-
START TIME
END TIME
CHANNEL
¡To temporarily stop recording or to resume it, press
PAUSE. After the VCR has been in Pause mode for
5 minutes, it will stop automatically to protect the
tape and the video head from damage.
REC SPEED
4
Set the timer.
¡To go back one step, press s.
2
Note
Press STOP when the recording is completed.
1) Set the program number (1-8)
PROGRAM NUMBER
4
DATE
- - / - -
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
Program number which is not set up
flashes. Press K or L repeatedly
for the desired program number.
Then, press B.
¡When you wish to watch another program while
recording, select desired channel on your TV. If
noise appears press VCR/TV.
¡This is not possible when using a cable box or
satellite box.
EN
–
–
19
1L25
¡If a tape ends during TIMER RECORDING, the
VCR will stop, eject the tape, and switch to the DVD
mode automatically as the TIMER REC light blinks.
(If the DVD power is off, the VCR will become
STANDBY status).
2) Set the frequency of the recording
For once: Press K or L to point to
"ONCE".
PROGRAM NUMBER
4
ONCE
DAILY
WEEKLY
For daily (Monday~Friday): Press
or L to point to "DAILY".
For weekly: Press K or L to point
to "WEEKLY".
K
¡
If a tape is not in the VCR or does not have a safety tab,
the TIMER REC light flashes and timer recording will
not operate. Please insert a recordable tape.
Then, press B.
¡
When all timer recordings are finished, the TIMER
REC light will flash. To use the VCR again as usual,
press T-SET to disable the flashing TIMER REC light,
then press VCR/TV to select the VCR position. Select
either VCR or DVD mode, then continue with the
other features as described in this manual.
ONE TIME PROGRAM
PROGRAM NUMBER
DATE - - / - -
START TIME - - : - - - -
END TIME - - : - - - -
3) Set the date
4
First, press K or L for the month.
Then, press B. Next, press K or
L for the day. Then, press B.
CHANNEL
- -
REC SPEED - -
¡
When timer recordings are set, the TIMER REC light
will come on. To use the VCR as usual until the time for
the recording, press T-SET so that TIMER REC light
disappears. Press VCR/TV to choose the VCR position.
Select either VCR or DVD mode, then continue with
ONE TIME PROGRAM
4) Set the start time
PROGRAM NUMBER
DATE 05 /12 MON
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
4
First, press K or L for the hour.
Then, press B. Next, press K or
for the minute. Then, press B. And
then, press K or L for AM or PM. Then, press B.
L
the other features as described in this manual
.
If you want to use the DVD player during
a VCR timer recording or while the TIMER
REC light is on or flashes.
You can use the DVD player while the TIMER REC
light is on or flashes, or during a timer recording.
Press POWER to turn on the DVD. Press DVD on the
remote control to choose DVD mode, then continue
with the other DVD features as described in this man-
ual. You don’t have to set the TIMER off to use the
DVD only.
ONE TIME PROGRAM
PROGRAM NUMBER
DATE 05 /12 MON
START TIME 07: 30 PM
END TIME - - : - - - -
5) Set the end time
4
Follow the instructions of
"Set the start time" to set
the end time.
¡
CHANNEL
- -
REC SPEED - -
ONE TIME PROGRAM
6) Set the channel number
PROGRAM NUMBER
DATE 05 /12 MON
START TIME 07: 30 PM
END TIME 08: 30 PM
CHANNEL - -
REC SPEED - -
4
Press K or L repeatedly for the
desired channel number. Then,
press B.
TO STOP AN AUTOMATIC TIMER PRO-
GRAM ALREADY STARTED
Press STOP/EJECT on the DVD /VCR COMBINA-
TION UNIT.
If you connected the DVD/VCR COMBINATION UNIT to
a cable box or satellite box as in "DVD/VCR TO TV
CONNECTION" on page 13, select the DVD/VCR to channel 3
or 4 the same channel as RF output channel of the DVD/VCR.
Then, select the channel you want to record with the cable box
or satellite box.
TO CHECK, CORRECT, OR CANCEL AN
AUTOMATIC TIMER PROGRAM
Leave the cable box or satellite box on for timer recording.
ONE TIME PROGRAM
7) Set the tape speed
PROGRAM NUMBER
DATE 05 /12 MON
START TIME 07: 30 PM
END TIME 08: 30 PM
CHANNEL 16
4
1
Press T-SET.
Press K or L repeatedly for the
desired tape speed. Then, press B.
¡If the DVD output mode is selected, you have to
switch it to the VCR mode by pressing the VCR on
the remote control or the OUTPUT on the VCR.
REC SPEED SP
SP
SLP
2
3
Select main menu by pressing MENU.
5
6
To set another program, repeat step [4]. To
exit, press CLEAR/C.RESET.
Select "TIMER PROGRAMMING" by press-
ing K or L. Then, press B.
Press T-SET to set the timer.
¡The TIMER REC light on the DVD/VCR COMBI-
NATION UNIT comes on. TIMER RECORDING
WILL NOT BE ACTIVATED UNLESS YOU
PRESS T-SET.
4
Select the program number you want to
check by pressing K or L.
¡The details of the selected program appears on the
TV screen.
¡Go to the digit you want to change by pressing B or
s. Then, enter correct numbers by pressing o or p.
HINTS FOR TIMER
RECORDING
¡You may cancel the entire program by pressing
s
while the program number flashes.
VCR
5
6
Press CLEAR/C.RESET to exit.
¡If there is a power failure or the VCR is unplugged
for more than 30 seconds, the clock setting and all
timer settings will be lost.
Press T-SET to return to timer stand-by mode
.
EN
–
–
20
1L25
SPECIAL FEATURES
TO MONITOR THE RECORDING
COPYING A VIDEO TAPE
1
Turn on the TV and set the TV to channel 3.
VCR
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same channel
(CH4) on your TV. (See “RF OUTPUT
CHANNEL” on page 13 for the detail).
You can make copies of video tapes made by friends or
relatives for your enjoyment.
You can not copy a DVD to a videotape.
Warning:
Unauthorized recordings of copyrighted video tapes
may be an infringement of copyright laws.
Connect the recording VCR (this unit), the playing
VCR (another source) and your TV using the follow-
ing diagram.
¡You can use the AUDIO/VIDEO input jacks on the
front panel of the DVD/VCR instead of using the
jacks on the back.
2
Press VCR/TV on the recording VCR.
MTS (Multi-Channel Television
Sound) SYSTEM
VCR
[Recording VCR]
(this unit)
When you play a VHS tape, or receive a broadcast on
the VCR’s tuner, the current sta-
tus will appear when you press
DISPLAY on the remote control.
When you record a MTS broad-
cast signal, you need to set it to
MTS mode.
STOP
12:00AM
CH 32
STEREO
SAP
DVD/VCR
VCR
DVD
AUDIO OUT
S-VIDEO COMPONENT AUDIO
DIGITAL
AUDIO IN
1)*
2)*
OUT
VIDEO OUT OUT
Y
AUDIO OUT
ANT-IN
L
L
R
R
Cb
Cr
L
COAXIAL
ANT-OUT VIDEO OUT
VIDEO IN
R
SP
0:00:00
HIFI
RF cable
(supplied)
Audio/Video cables
(not supplied)
1)* Press MENU and select "TV STEREO" or
[TV set]
(Use for monitoring)
"SAP" by pressing K or L. Then, press
to select mode. To exit, press
B
OUT IN
CLEAR/C.RESET.
LEFT
AUDIO
RIGHT
¡Although a program may be broadcast in both stereo
and sub audio, you must select the Recording mode
to TV STEREO or SAP before you record a broad-
cast.
VIDEO
[Playing VCR]
(another source)
ANT in
1
2
Insert a pre-recorded tape into the playing VCR.
2)* Press MENU and select "AUDIO OUT" by
pressing K or L. Then, press B. Next,
select "HIFI" or "MONO" by pressing K or
L. To exit, press CLEAR/C.RESET.
Insert a tape with a safety tab into the
recording VCR.
3
4
Press SPEED on the recording VCR to select the
desired recording speed (SP/SLP)
¡While the VCR is set in HIFI stereo mode, HIFI
appears on the TV screen. While the VCR is set in
monaural (MONO) mode, HIFI disappears from the
TV screen.
.
Select the “L1” or “L2”position on the
recording VCR.
¡
When you use the A/V input jacks on the back of the
DVD/VCR, select "L1" position by pressing [0], [0], [1]
on the remote control or the CHANNEL buttons (o/p).
MTS RECORDING/MONITOR MODE
Display on the
TV screen
Type of
STEREO/SAP
Selection
Hi-Fi audio track
(2-channel)
L-channel R-channel
Normal audio
track
¡
When you use the A/V input jacks on the front of the
DVD/VCR, select "L2" position by pressing [0], [0], [2]
on the remote control or the CHANNEL buttons (o/p).
broadcast
Regular
(monaural audio)
-None-
-Invalid-
Mono
L
Mono
R
Mono
L+R
Stereo
broadcast
STEREO
SAP
-Invalid-
TV STEREO*
SAP*
5
6
Press REC/OTR on the recording VCR.
Main audio Main audio Main audio
program
program
program
Bilingual
broadcast
Begin playback of the tape in the playing
VCR.
Sub audio Sub audio
Sub audio
program
program
L
program
R
TV STEREO*
SAP*
L+R
Sub audio
program
Stereo &
Bilingual
broadcast
STEREO
SAP
¡For best results during dubbing, use the VCR’s front
panel controls whenever possible. The remote con-
trol might affect the playing VCR’s operation.
¡Always use video-quality shielded cables with
RCA-type connectors. Standard audio cables are not
recommended.
Sub audio Sub audio
program program
*
¡You can use a video disc player, satellite receiver, or
other audio/video component with A/V outputs in
place of the playing VCR.
EN
–
–
21
1L25
AUTO REWIND
REAL TIME TAPE COUNTER
When a tape reaches the end during recording, play-
back, or fast-forward, the tape will automatically
rewind to the beginning. After rewinding finishes, the
VCR will eject the tape and switch itself off.
¡The VCR will not rewind the tape automatically dur-
ing timer recording or One Touch Recording.
¡This shows the elapsed recording or playback time
in hours, minutes, and seconds. (The displayed time
will not change during blank portions of the tape.)
¡The indication will appear when the tape is rewound
further than “0:00:00” on the tape counter.
PLAYING A DISC
Notes
BASIC PLAYBACK
¡A “prohibited icon” may appear at the top-right on
the TV screen during operation, warning that a pro-
hibited operation has been encountered by the DVD
or the disc.
¡With DVDs that use titles for playback program sig-
nals, playback may start from the second title, or it
may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a mal-
function.
DVD-V
CD
Getting started
¡Turn on the power of the TV, amplifier and any other
components which are connected to the DVD.
¡Make sure the TV and audio receiver (commercially
available) are set to the correct channel.
¡Select DVD mode by pressing DVD on the remote
control or output on the front panel.
1
Press POWER.
¡“Load” will appear briefly on the display panel.
GENERAL FEATURES
DVD may contain menus to navigate the disc and
access special features. Press appropriate numerical
key or use Arrow (L/K/s/B) to highlight your selec-
tion in the DVD main menu and press ENTER to con-
firm.
2
3
Press OPEN/CLOSE to open disc loading
tray.
Place the chosen disc in the tray, with the
label facing up.
Note
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
PAUSE
DVD-V
CD
4
Press PLAY.
¡The tray will close automatically, and playback will
then start from the first chapter or track of the disc.
If the playback does not start automatically, press
PLAY.
¡When you playback the DVD which a title menu is
recorded, it may appear on the screen. In this case,
refer to “TITLE MENU” on page 23.
1
During playback, press PAUSE.
¡Playback will pause and sound will be muted.
2
To continue playback, press PLAY.
5
Press STOP to stop playback.
EN
–
–
22
1L25
DISC MENU
STEP BY STEP PLAYBACK
DVD-V
DVD-V
1
Press MENU.
¡The DVD main menu will appear.
1
During playback, press PAUSE.
¡Playback will pause and sound will be muted.
2
3
If the feature is not available,
may appear on the TV screen.
symbol
2
3
The disc goes forward by one frame each
time PAUSE is pressed.
If disc menu is available on the disc, audio
language, subtitle options, chapters for the
title and other options will appear for selec-
tion.
To exit step by step playback, press PLAY.
RESUME
DVD-V
CD
4
Press Arrow (L/K/s/B) to select an item,
and ENTER to confirm selection.
1
During playback, press STOP.
¡Resume message will appear on the TV screen.
TITLE MENU
2
Press PLAY, playback will resume from the
point at which playback was stopped.
DVD-V
¡To cancel resume, press STOP twice.
1
Press TITLE.
¡The title menu will appear.
FAST FORWARD/REVERSE
SEARCH
2
3
If the feature is not available,
may appear on the TV screen.
symbol
DVD-V
CD
MP3
Press Arrow (L/K/s/B) to select an item,
and ENTER to confirm selection.
1
During playback, press g or h repeat-
edly to select the required forward or
reverse speed: x2, x8, x50, x100 .
CALLING UP A MENU SCREEN
¡For audio CDs, the speed is fixed at ×16.
¡For MP3, the speed is fixed at ×8.
DURING PLAYBACK
¡Press MENU to call up the DVD menu.
¡Press TITLE to call up the title menu.
Note
2
To return to normal playback, press PLAY.
¡Contents of menus and corresponding menu opera-
tions may vary between discs. Refer to the manual
accompanying the disc for details.
SLOW FORWARD /
SLOW REVERSE
DVD-V
1
2
3
During playback, press PAUSE.
Press g or h .
Press g or h repeatedly to select the
required speed: 1/16, 1/8, 1/2 of the normal
playback.
4
To return to normal playback, press PLAY.
EN
–
–
23
1L25
Using SKIP
H
G
ZOOM
During playback, press SKIP G to move the next
track. Press it repeatedly to skip subsequent tracks.
Press SKIP H to go back to beginning of the current
track. Press it repeatedly to go to the previous tracks.
¡Track number will appear briefly on the DVD/VCR
COMBINATION UNIT display panel.
DVD-V
The Zoom function allows you to enlarge the video
image and to pan through the enlarged image.
¡If SKIP is pressed while the playback is paused, the
playback will be paused again after skipping to the
next track.
1
Press ZOOM during playback.
¡Playback will continue.
Note
¡SKIP
stopped.
2
3
Press ZOOM repeatedly to select the
required zoom factor: x2, x4 or OFF.
H
G are not available when playback is
Use the Arrow (K/L/s / B) to move the
zoomed picture across the screen.
TITLE / CHAPTER SEARCH
4
Notes
To exit zoom mode, press ZOOM to OFF.
DVD-V
¡Zooming function does not work while disc menu is
shown.
¡x4 zoom is not available on some discs.
1
Press SEARCH MODE once for the Chapter
search, twice for the Title search during
playback.
/2
TRACK
CD
2
Enter the desired chapter/title number using
numerical buttons.
There are three ways to begin playback on an Audio
CD at a specific Track.
¡Playback will start at the selected Chapter or Track.
¡Press CLEAR to erase the incorrect input.
¡For single digits press 0 first.
Using the Numerical buttons
1
Press Numerical buttons to enter the
desired Track number.
TIME SEARCH
¡Playback will start at the selected track.
¡For single digit tracks (1-9), press a single number
(eg. track 3, press 3).
DVD-V
CD
¡To play track 26, press +10, 2, 6 on the numerical
button.
Using SEARCH MODE
1
2
During playback, press SEARCH MODE
three times (CD: twice) to display the Time
Search on the TV screen.
1
Press SEARCH MODE.
¡The track search display appears.
Within 30 seconds, enter a desired disc
time using numerical buttons.
2
Within 30 seconds, select a desired track
number using numerical buttons.
¡Playback will start at the specified time.
¡For single digits press 0 first.
¡Playback will start at the selected track.
¡Press CLEAR to erase the incorrect input.
EN
–
–
24
1L25
REPEAT
REPEAT is available only during playback.
REPEAT TITLE / CHAPTER
REPEAT A-B
DVD-V CD
DVD-V
1
2
Press REPEAT A-B at your chosen starting
point.
A- appears briefly on the TV screen.
To activate the repeat function, press REPEAT
during playback.
¡The repeat mode changes as described below every
time you press the button.
¡
¡
Press REPEAT A-B again at your chosen
end point.
A-B appears briefly on the TV screen, and the
CHAPTER
TITLE
OFF
repeat sequence begins.
(repeat off)
(current chapter repeat) (current title repeat)
3
To exit the sequence, press REPEAT A-B.
Notes
Notes
¡
The repeat A-B section can only be set within the cur-
rent title (for DVDs), or current track (for audio CDs).
Repeat A-B is not available with some scenes in DVD.
¡Repeat Title/Chapter is not available with some
scenes.
¡
¡The REPEAT setting will be cleared when moving
to other title or chapter.
¡To cancel the A point which was set, press CLEAR.
¡Repeat A-B playback does not function during title,
chapter, track or all repeat playback.
REPEAT TRACK
CD
To activate the repeat function, press REPEAT
during playback.
PROGRAM
¡The repeat mode changes as described below every
time you press the button.
CD
You may determine the order in which tracks will play.
TRACK
ALL
OFF
(repeat off)
(current track repeat)
(entire disc repeat)
1
In stop mode, press MODE.
¡The PROGRAM screen will appear.
Notes
¡Track Repeat setting will be cleared when moving to
other track.
¡Repeat playback does not function during repeat A-
B playback.
2
Press L or M to select a track, then press
ENTER.
¡Press CLEAR to erase the
most recently entered pro-
gram.
CD [AUDIO]
TOTAL 0:03:30
MP3
TRACK
GROUP
ALL
OFF
(repeat off)
(current track
(current group
(entire disc
repeat)
repeat)
repeat)
3
Notes
Press PLAY to play the programmed tracks.
¡While the program is being played back, the STOP
works as follows.
¡Press STOP once and then PLAY again, playback
will restart from the point where STOP was pressed.
(Program continued)
¡Press STOP twice and then PLAY again, playback
will restart from the track in the usual way. (Program
cleared)
¡Up to 99 programs can be entered.
¡If you like to repeat the current track in the program,
press REPEAT repeatedly until
TRACK appears
during playback. If you like to repeat the entire pro-
gram press REPEAT repeatedly until
appears during playback.
ALL
EN
–
–
25
1L25
Notes
RANDOM PLAYBACK
¡Folders are known as Groups; files are known as
Tracks.
¡MP3 files are accompanied by
CD
3
icon.
¡Maximum of 255 folders can be recognized.
¡Maximum of 256 files can be recognized.
¡Up to 8 hierarchies can be created.
This shuffles the playing order of tracks instead of
playback in the sequence.
This player recommends the use of files recorded at
the below specifications:
¡Sampling frequency: 44.1kHz or 48kHz
¡Constant bit rate: 112kbps ~ 320kbps.
1
In stop mode, press MODE twice.
¡RANDOM screen
RANDOM
appears.
CD [AUDIO]
TOTAL 0:45:55
RANDOM PROGRAM
--no indication--
INFORMATION
ON-SCREEN
PLAY
MP3
You can check the MP3 files during playback.
2
Press PLAY to start random playback.
Note
1
Press DISPLAY.
¡The name of the file currently in play will be dis-
¡If you like to repeat the current track in the random
selection, press REPEAT repeatedly until
TRACK appears during playback. If you like to
repeat the entire random selection press REPEAT
played.
2
Press DISPLAY again to show the track
number, the repeat status, and the playback
status at the top of the screen.
repeatedly until
ALL appears during playback.
MP3 PLAYBACK
¡
will be displayed when repeat play has been
selected.
MP3
T - indicates Track repeat
When a CD with MP3 files is inserted in the
DVD/VCR, the MP3 menu will appear on the TV
screen, and number of tracks is displayed on the front
panel.
G - indicates Group (folder) repeat
A - indicates Disc repeat
3
1
Press DISPLAY again to exit.
1
In stop mode, press Arrow (K/L) to select
the desired group track.
TRACK SELECTION
¡If a group is selected,
press or ENTER to go
B
MP3
on to the track selection
screen. Press Arrow (K/L)
to choose a track, then
Press SEARCH MODE during playback.
¡The FILE LIST will appear.
press
¡If a track is selected, press
or ENTER to start playing tracks. Starting from
B
or ENTER.
2
Select a desired track using Arrow
(K/L/s/B).
¡Press B when you want to go to the next hierarchy.
¡Press s when you want to go back to the previous
hierarchy.
B
the one you’ve just chosen the subsequent tracks
will be played.
¡Choose FIRST PLAY to start playback from the
beginning of the listed tracks.
¡Press TITLE to return to the first item.
3
Press PLAY to start playing.
Notes
2
Press STOP to stop playback.
¡Press SEARCH MODE to exit.
¡Some selections may take a while to be recognized.
EN
–
–
26
1L25
RANDOM PLAYBACK
SUBTITLE LANGUAGE
MP3
DVD-V
The DVD allows you to select a language for subtitles
during DVD disc (if available) playback.
1
2
Press MODE twice while playback is
stopped.
1
2
Press SUBTITLE during playback.
Press PLAY to play the tracks in random
order.
Press SUBTITLE repeatedly to select your
desired subtitle language.
PROGRAM
¡The subtitle language will be displayed on the dis-
play bar at the top of the screen.
MP3
3
To turn off subtitles, press SUBTITLE
repeatedly until OFF appears.
This feature allows you to program a mp3 disc to play
in a desired sequence.
Notes
¡Pressing AUDIO may not work on some DVDs with
multiple audio languages (e.g. DVDs which allow
audio language setting on the disc menu).
¡Some discs allow audio language setting/subtitle
language setting on the disc menu. (Operation varies
between discs, so refer to the manual accompanying
the disc.)
1
Press MODE during playback is stopped.
¡The PROGRAM screen will appear.
2
Press Arrow (K/L) to select a track, then
press ENTER, to save it in a program.
¡Press CLEAR to erase the incorrect input.
¡If the desired language is not shown after pressing
SUBTITLE several times, the disc does not have
subtitles in that language.
3
Press PLAY to start programmed playback.
¡If you choose a Language that has a 3 letter language
code, the code will be displayed every time you
change the Subtitle language setting. If you choose
any other languages, ‘---’ will be displayed instead.
(Refer to page 31.)
AUDIO LANGUAGE
DVD-V
The DVD/VCR allows you to select a language during
DVD disc (if multi language available) playback.
CAMERA ANGLE
DVD-V
1
2
Press AUDIO during playback.
Some DVD discs contain scenes which have been shot
simultaneously from various angles. You can change
Press AUDIO repeatedly to select your
desired language.
the camera angle when the (
screen.
) icon appears on the
STEREO SOUND MODE
1
Press ANGLE during playback.
CD
¡The selected angle will be displayed on the display
bar at the top of the screen.
1
Press AUDIO repeatedly during playback to
select between STEREO, L-CH or R-CH.
2
Press ANGLE repeatedly to select your
desired angle.
¡STEREO - both right and left channels are active
(stereo)
L-CH - only left channel is active
R-CH - only right channel is active
Note
¡If the Virtual Surround setting is ON, the sound
mode will be fixed to STEREO, and can not be
changed.
EN
–
–
27
1L25
CHANGING THE ON-SCREEN
DISPLAY
PARENTAL CONTROL
DVD-V
DVD-V
CD
Parental Control limits the disc viewing that exceed
your settings. (with a password or playback will stop.)
This feature allows you to prevent discs with alterna-
tive scenes from being played by your children.
You can check the information about the current disc
by pressing DISPLAY on the remote control.
For DVD-Vs
PARENTAL LEVEL
1
Press DISPLAY during playback to show
current Chapter.
Parental Level allows you to set the rating level of
your DVD discs. Playback will stop if the disc’s rat-
ings exceed the level you set.
¡The elapsed and remaining
playing time of the current
chapter will be displayed.
9/49
0:00:00 -0:00:00
1
2
Press SETUP in STOP mode.
Press B to select CUSTOM, then press
ENTER.
2
Press DISPLAY again to show current Title.
¡The elapsed and remaining playing time of the cur-
rent title will be displayed.
3
Press Arrow (s/B) to select PARENTAL,
then press ENTER.
3
Press DISPLAY third time.
¡The BIT RATE and the current repeat setting will be
displayed.
PARENTAL
PARENTAL LEVEL ALL
¡If you are playing a dual layered disc, the layer num-
ber will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
4
5
6
Enter your four-digit password then press
ENTER.
4
Press DISPLAY the fourth time to remove
the display.
Press Arrow (K/L) to select PARENTAL
LEVEL, then press ENTER.
For audio CDs
1
Press DISPLAY during playback, the current
Track will be displayed on the TV screen.
Press Arrow (K/L) to select the desired
level.
¡The elapsed and remaining playing time of the cur-
rent track will be displayed.
7
Press SETUP to exit
Notes
2
Press DISPLAY again to show current Total
Track.
¡When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the
password. (in the event you forget the password, see
below.)
¡The elapsed and remaining playing time of the cur-
rent total track will be displayed.
¡To change the password, press Arrow (K/L) to
select CHANGE at step 5, then press ENTER. Enter
the four-digit pass-word, then press ENTER.
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
3
Press DISPLAY third time to remove the dis-
play.
¡Record the password in case you forget it.
IF YOU FORGET THE PASSWORD
1
Press 4, 7, 3, 7 at step 4. Then enter your
new password.
¡Password will be cleared and parental level will be
set to ALL.
2
Proceed the above Steps 5-7 again.
EN
–
–
28
1L25
CONTROL LEVELS
2
3
Press Arrow (s /B) to select 1, 2, 3, 4, 5, 6,
7, 8, 9, or 10 and ensure that “- : - - : - -”
appears in the display.
¡
ALL
All parental lock is cancelled.
¡
Level 8
DVD software of any grade (adult/general/children)
can be played back.
When reaches the desired point, press
ENTER.
¡
Levels 7 to 2
¡The Title or Track and elapsed playing time will
appear in the TV screen.
Only DVD software intended for general use and
children can be played back.
¡
Level 1
4
To return to the Marker later, press SEARCH
MODE four times (CD: three times) during
playback and Arrow (s /B) to choose the
desired marker, then press ENTER.
Only DVD software intended for children can be
played back, with those intended for adult and
general use prohibited.
Notes
¡Opening the disc tray or turning off the power or
select AC at step 2 and press ENTER will erase all
Markers.
MARKER SETUP SCREEN
DVD-V
CD
¡To clear a marker, using Arrow (s /B), position the
cursor on to the marker number to be cleared and
press CLEAR.
¡You can mark up to 10 points.
Use markers to memorise your favorite places on a
disc.
1
Press SEARCH MODE four times (CD: three
times) during playback.
5
Press SEARCH MODE or RETURN to exit.
¡The display screen and Markers will appear on the
TV screen.
DVD SETUP
DOLBY DIGITAL:
Set to On when the unit is connected to a Dolby Digital
QUICK
AUDIO SETTING
Choose the appropriate Audio settings for your equip-
ment as it only affect during the playback of DVD
discs.
Receiver.
(ON: Outputs a Dolby Digital Signal)
(OFF: Convert the Dolby Digital to PCM (2channel))
¡The default setting is ON.
DOWN SAMPLING:
¡Set to ON when outputting in 48 kHz.
¡The default setting is ON.
When playing disc with copyright Protection
¡If you select OFF, copyright protection will be acti-
vated and sound will be down sampled at 48kHz.
1
2
Press SETUP in STOP mode.
Press B to select CUSTOM, then press
ENTER.
¡CUSTOM mode will appear.
3
Press Arrow (s / B) to select AUDIO, then
press ENTER to confirm.
5
Press SETUP to exit.
AUDIO
DRC
OFF
ON
DOLBY DIGITAL
DOWN SAMPLING ON
4
Press Arrow (K/L) to select the below
items, then press ENTER.
DRC (Dynamic Range Control):
¡To compress the range of soft to loud sounds.
¡The default setting is OFF.
EN
–
–
29
1L25
BLACK LEVEL SETTING
DISPLAY SETTING
DVD-V
DVD-V
Adjust the Black Level Settings to make the black You can change certain aspects of the DVD display
parts of the picture as bright as you preferred. screens and on-screen messages.
1
Press MODE during playback.
1
2
Press SETUP in STOP mode.
ON
Press B to select CUSTOM, then press
ENTER.
¡CUSTOM mode will appear.
2
Press ENTER to switch ON/OFF.
ON: Makes the dark parts brighter.
3
Press Arrow (s /B) to select DISPLAY, then
press ENTER to confirm.
OFF: Shows the original picture as recorded.
3
Press MODE twice or RETURN to exit.
DISPLAY
TV ASPECT
4:3 LETTER BOX
ON
ANGLE ICON
AUTO POWER OFF ON
VIRTUAL SURROUND
DVD-V
CD
MP3
4
Press Arrow (K/L) to select the below
items, then press ENTER.
You can enjoy stereophonic visual space on your exist-
ing stereo system.
TV ASPECT:
¡Press Arrow (K/L) for an item selection, then press
QUICK
ENTER.
1
Press MODE twice (CD/MP3: once) during
¡Select 4:3 LETTER BOX for a black bars appears
on top and bottom of the screen.
¡Select 4:3 PAN & SCAN for a full height picture
with both sides trimmed.
playback.
OFF
¡Select 16:9 WIDE if a wide-screen TV is connected
to the DVD/VCR.
¡The default setting is 4:3 LETTER BOX.
ANGLE ICON:
¡Press ENTER repeatedly to turn Angle icon ON or
OFF.
¡The default setting is ON.
AUTO POWER OFF:
¡Press ENTER repeatedly to turn Auto Power off ON
or OFF.
2
3
Press ENTER to set it 1 (Natural effect) or 2
(Emphasized effect) or OFF.
Press MODE or RETURN to exit.
Note (for CD play only)
¡Virtual Surround will not be effective if the sound
mode is set to something other than STEREO.
¡The default setting is ON and it will turn the
DVD/VCR to off automatically after 35 minutes of
no use.
5
Notes
Press SETUP to exit.
¡Be sure to press SETUP, or the setting will not work.
EN
–
–
30
1L25
AUDIO:
¡Sets the audio language.
SUBTITLE:
¡Sets the subtitle language.
DISC MENU:
¡Sets the language for DVD menu.
LANGUAGE SETTING
DVD-V
Language options are not available with some discs.
PLAYER MENU:
¡Sets the language for the On-screen display.
QUICK
1
2
Press SETUP in STOP mode.
Press B to select CUSTOM, then press
ENTER.
5
Press Arrow (K/L) to select a setting, then
press ENTER.
¡CUSTOM mode will appear.
¡If OTHER is selected on the AUDIO, SUBTITLE or
DISC MENU screen, press four-digit number to
enter the code for the desired language. (Refer to the
language code list below.)
3
Press Arrow (s / B) to select LANGUAGE,
then press ENTER to confirm.
¡Only the languages supported by the disc can be
selected.
LANGUAGE
AUDIO
ORIGINAL
OFF
ENGLISH
ENGLISH
6
Note
Press SETUP to exit.
SUBTITLE
DISC MENU
PLAYER MENU
¡Language Setting for Audio and Subtitle is not avail
able with some discs. Then use the AUDIO and the
SUBTITLE button. Details are on page 27.
4
Press Arrow (K/L) to select the next items,
then press ENTER.
¡If you want to return to LANGUAGE SETTING
MENU, press Arrow(s ).
Language
Code
Language
Frisian
Code
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
Language
Malay
Code
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
Language
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
T
Code
6561
5165
6567
6569
6568
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
Galician
Malayalam
Maltese
Maori
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Marathi
Moldavian
Mongolian
Nauru
Tagalog
Tajik
Tamil
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
Nepali
Norwegian [NOR]
O-R
Occitan
Tatar
Telugu
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
Thai
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Tibetan
Tigrinya
Tonga
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
Tsonga
Turkish [TUR]
Turkmen
Twi
Bulgarian
Burmese
Byelorussian
U-Z
Ukrainian
Urdu
Uzbek
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
C-E
Cambodian
Catalan
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Chinese [CHI]
Corsican
Croatian
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
Korean [KOR]
Kurdish
L-N
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
Macedonian
Malagasy
5861
5847
5868
5860
5866
5957
5953
F-H
Faroese
Fiji
Finnish [FIN]
French [FRE]
5261
5256
5255
5264
Singhalese
Siswat
Slovak
Slovenian
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change
the Audio or Subtitle language setting on page 27. If you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
EN
–
–
31
1L25
TROUBLESHOOTING GUIDE
If the DVD/VCR COMBINATION UNIT does not perform properly when operated as instructed in this
Owner's Manual, check the player consulting the following checklist.
PROBLEM
No power.
CORRECTIVE ACTION
D
V
D
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
The player does not respond to. • Check if the power plug is connected to an AC outlet.
the remote control.
• Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary, remove all the
obstacles between the sensor and the remote.
• You have to be within 23 feet of the player.
• Check if the correct mode is selected. If not switch the mode by pressing DVD or
VCR ,whichever you need, on the remote control.
V
C
R
• Check if a cassette tape is in the VCR.
Timer recording is impossible. • Make sure the timer recording is set correctly.
• Make sure the power is off.
V
C
R
• Make sure the VCR clock is set correctly.
Cannot go into Record mode. • Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.
• Put he player in VCR mode. Press VCR on the remote control so that the green VCR
OUTPUT light is lit.
(
)
Playback picture is partially noisy • Adjust tracking control for a better picture by pressing CHANNEL
on the
DVD/VCR COMBINATION UNIT.
Cannot view a tape but the
• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .
• Make sure the VCR is not in the Menu mode.
.
audio is OK
No, or poor, playback picture.
• Change the RF output channel to CH4. Then select the same channel on the TV.
• Fine tune your TV.
TV programs cannot be seen
normally.
• Re-check the ANT. IN and ANT. OUT connections. See page 13.
• Press VCR/TV.
• Press VCR on the remote control to put it in the VCR mode. Check if the green VCR
OUTPUT light is lit. Then, set it to the TV position by pressing VCR/TV.
Video or color fades in and out
when making a copy of a video tape.
•
You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
Cannot remove the tape.
• Check if the player is in the VCR mode. If not, press VCR on the remote control to switch
the mode.
No picture.
• Connect the video cables firmly.
D
V
D
• Insert a correct video disc that plays on this player.
• Press DVD on the remote control. Check if the DVD OUTPUT Light is lit. Then try other
DVD feature.
• Insert the disc.
• Clean the disc.
.
Disc cannot be played
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
• Connect the audio cables firmly.
.
No sound
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• This player does not support DTS audio. This is not a malfunction.
• Connect the player directly to the TV.
.
No DTS audio is output
.
Distorted picture
•
There are some cases where pictures may be slightly distorted, which are not a sign of a mal-
function.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language
does not match the set up
The camera angle cannot be
changed
•
The selected language is not available for audio or subtitles on the DVD.
This is not a malfunction
The DVD does not contain sequences recorded from different camera angles.
This is not a malfunction
•
Audio or subtitle language
cannot be changed
• The DVD does not contain audio source or subtitles in the selected language.
This is not a malfunction.
“Prohibited icon” appears on the • That operation is prohibited by the player or the disc.
screen, prohibiting an operation This is not a malfunction.
Notes
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this
Owner’s Manual for details on correct operations.
¡Playback from a desired track and random playback are not available during program playback.
EN
–
–
32
1L25
MAINTENANCE
AUTO HEAD CLEANING
SERVICING
¡Should your DVD/VCR COMBINATION UNIT ¡Automatically cleans video heads as you insert or
become inoperative, do not try to correct the prob- remove a cassette, so you can see a clear picture.
lem by yourself. There are no user-serviceable parts ¡Playback picture may become blurred or interrupted
inside. Turn off, unplug the power cord, and please
call our help line at 1-800-287-4871 to locate an
Authorized Service Center.
while the TV program reception is clear. Dirt accu-
mulated on the video heads after long periods of use,
or the usage of rental or worn tapes can cause this
problem. If a streaky or snowy picture appears dur-
ing playback, the video heads in your DVD/VCR
COMBINATION UNIT may need to be cleaned.
CLEANING THE CABINET
¡Use a soft cloth slightly moistened with a mild deter-
gent solution. Do not use a solution containing alco-
hol, spirits, ammonia or abrasive.
1. Please visit your local Audio/Video store and pur-
chase a good quality VHS Video Head Cleaner.
CLEANING DISCS
2. If a Video Head Cleaner does not solve the prob-
lem, please call our help line at 1-800-287-4871 to
locate an Authorized Service Center.
¡When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not wipe
in a circular motion.
NOTES:
¡Do not use solvents such as benzine, thinner, com-
mercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for ana-
logue records.
¡Remember to read the instructions included with the
video head cleaner before use.
• Clean video heads only when problems occur.
CLEANING THE DISC LENS
¡If the player still does not perform properly when it
is operated while referring to the relevant sections
and to “TROUBLESHOOTING GUIDE” in this
Owner’s Manual, the laser optical pickup unit may
be dirty. Consult your dealer or an Authorized
Service Center for inspection and cleaning of the
laser optical pickup unit.
DISC HANDLING
¡Use discs which have the following logos on them.
(Optical audio digital discs.)
Recordable
ReWritable
¡Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
¡Always store the disc in its protective case when it is
not used.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your council for details.
EN
–
–
33
1L25
SPECIFICATIONS
Product type:
Discs:
DVD player with Video Cassette Recorder
DVD video
Audio CD
Video Cassette tape
Converter output:
Power source:
VHF Channel 3 or 4.
120 V AC +/- 10%, 60 Hz +/- 0.5%
24 W (standby: 7.0 W)
5°C to 40°C
Power consumption:
Operating temperature:
Dimensions:
W 17-1/8” (435 mm)
H 4” (99 mm)
D 8-7/10” (218 mm)
8.8 lbs (3.7 kg)
Weight:
¡Designs and specifications are subject to change without notice.
¡If there is a discrepancy between languages, the default language will be English.
EN
–
–
34
1L25
MEMO
EN
–
–
35
1L25
EMERSON HOME ENTERTAINMENT WARRANTY
We appreciate your purchase of a EMERSON Home Entertainment product. We take pride in the
quality of our products and have manufactured your new Home Entertainment unit to exacting quality
standards. We feel confident that in normal use, it will provide you with satisfactory performance.
However, should you experience difficulty, you are protected under the provisions of this warranty.
EMERSON Home Entertainment products are warranted against manufacturing defects in materials
and workmanship in normal use for the following period from the date of purchase by the original
user, and is conditional upon the unit being installed and used as directed in the instruction manual.
PRODUCT
PARTS AND LABOUR
D.V.D. / VCR
Video Head
1 year
6 months
Remote Control 90 days
EMERSON's obligation under this warranty shall be limited to the repair, including all necessary parts
and the cost of the labour connected therewith, or at our option the exchange of any Home
Entertainment product which shows evidence of a manufacturing defect within the warranty period.
Replacement parts, furnished in connection with this warranty shall be warranted for a period equal to
the unexpired portion of the original equipment warranty.
CUSTOMER OBLIGATIONS
This warranty applies to the product from the original date of purchase at retail. Therefore, the owner
must provide a copy of the original, dated bill of sale. No warranty service will be performed without
a bill of sale. Transportation to and from the service depot is the responsibility of the owner.
WARRANTY EXCLUSIONS
This warranty is extended to EMERSON Home Entertainment products purchased and used in
Canada. This warranty shall not apply to appearance or accessory items including but not limited to:
antenna, cabinet, cabinet parts, knobs, batteries, connecting cables, cassette tapes, compact discs.
This warranty shall, in addition, not apply to damages due to handling, transportation, unpacking, set-
up, installation, customer adjustments that are covered in the instruction book, repair or replacement of
parts supplied by other than the EMERSON authorized service depot, any malfunction or failure
caused by or resulting from abnormal environmental conditions, improper unauthorized service,
improper maintenance, modifications or repair by the consumer, abuse, misuse, neglect, accident, fire,
flood, or other Acts of God, and incorrect line voltage.
This Home Entertainment product is only warranted to the original retail purchaser. This warranty
becomes void in the event of commercial or rental use. This warranty becomes void in the event serial
numbers are altered, defaced or removed.
EMERSON reserves the right to make changes in design or to make additions to or improvements
upon this product without incurring any obligation to install the same on products previously manufac-
tured. The foregoing is in lieu of all other warranties expressed or implied and EMERSON neither
assumes nor authorizes any person to assume for it any other obligation or liability in connection with
the sale or service of this product. In no event shall EMERSON or its EMERSON dealers be liable
for special or consequential damage arising from the use of this product, or for any delay in the perfor-
mance of this warranty due to cause beyond our control.
The purchaser may have other rights under existing provincial or federal laws, and where any terms of
this warranty are prohibited by such laws, they are deemed null and void, but the remainder of the
warranty shall remain in effect.
HOW TO OBTAIN SERVICE
Should this product require service, you may obtain specific information on how to obtain service by
contacting the EMERSON Dealer from whom this product was purchased, or by contacting us direct-
ly:
EMERSON SERVICE
300 Alden Road
Markham, Ontario
L3R 4C1
PHONE: (905) 940-5089 FAX: (905) 940-2303
1-800-287-4871
Printed in China
0VMN03693
#####
H9436CD
|