English
User’s Manual
FlexScan
L350
Color LCD Monitor
CONTENTS
PRECAUTIONS __________________________ 4
INTRODUCTION _________________________ 9
About this Manual .................................................... 9
Package Contents.................................................... 9
Controls & Connectors........................................... 10
1 INSTALLATION _______________________ 11
1-1 Connecting up ................................................. 11
PC Settings .......................................................................11
Connecting the Cables .....................................................12
Attaching an Arm to the Monitor .......................................13
2 USING THE SCREENMANAGER _________ 14
2-1 How to use the ScreenManager...................... 14
About ScreenManager......................................................14
ScreenManager Menus ....................................................14
How to use the ScreenManager .......................................16
Adjustment Lock ...............................................................17
2-2 Screen Adjustment .......................................... 18
Adjustment Procedure ......................................................18
2-3 Color Adjustment ............................................. 24
About Color Adjustment....................................................24
Color Mode .......................................................................24
Gain Adjustments .............................................................25
2-4 Power-save Setup ........................................... 26
Setup Procedure...............................................................26
2-5 Other Settings ................................................. 27
Off Timer ...........................................................................27
VGA Selection ..................................................................28
Menu Position ...................................................................28
Reset ................................................................................28
3 TROUBLESHOOTING _________________ 29
4 CLEANING __________________________ 32
CONTENTS
2
5 SPECIFICATIONS _____________________ 33
APPENDIX______________________________ i
E
Pin Assignment ........................................................ ii
Dimensions .............................................................. ii
Preset Timing Chart .................................................iii
Copyright© 1999 by EIZO NANAO CORPORATION. All rights reserved. No part of
this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or
by any means, electronic, mechanical, or otherwise, without the prior written permission of
Eizo Nanao Corporation.
Eizo Nanao Corporation is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to Eizo Nanao
Corporation's receipt of said information.
Although every effort has been made to ensure that this manual provides up-to-date
information, please note that EIZO monitor specifications are subject to change without
notice.
Apple and Macintosh are registered trademarks of Apple Computer Inc.,registered in the
U.S. and other countries.
DPMS is a trademark and VESA is a registered trademark of Video Electronics Standards
Association.
VGA is a registered trademark of International Business Machines Corporation in the USA
and other countries.
ENERGY STAR is a U.S. registered trademark.
Windows is a registered trademark of Microsoft Corporation.
ScreenManager and PowerManager are trademarks of Eizo Nanao Corporation.
FlexScan and EIZO are registered trademarks of Eizo Nanao Corporation.
CONTENTS
3
PRECAUTIONS
IMPORTANT!
* The manufacturer is not responsible for damage or malfunction caused by improper
connection. The power cord should be connected directly to a standard wall power
outlet.
Location of the caution statements on the back panel.
Risk of electric shock. Do not open.
Risque de choc electrique. Ne pas ouvrir.
Gefahr des elektrischen schlages. Rückwand nicht entfernen.
The equipment must be connected to a grounded main outlet.
Jordet stikkontakt skal benyttes nár apparatet
tilkobles datanett.
Apparaten skall anslutas till jordat nätuttag.
IMPORTANT!
To ensure personal safety and proper maintenance. Please
read this section and the caution statements on the LCD
monitor (refer to the figure above).
This manual uses the safety symbols below. They denote critical
information. Please read them carefully.
Indicates a prohibited action.
Indicates to ground for safety.
WARNING
Failure to abide by the information in a WARNING may result in
serious injury and can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in
moderate injury and/or property or product damage.
4
PRECAUTIONS
WARNING
E
• If the LCD monitor begins to emit smoke, smells like
something is burning, or makes strange noises,
disconnect all power connections immediately and contact
your dealer for advice.
Attempting to use a malfunctioning LCD monitor can be
dangerous.
• Do not dismantle the cabinet or modify the LCD monitor.
Dismantling the cabinet or modifying the monitor may result in
electric shock or burn.
• Keep small objects away from the LCD monitor.
Small objects may accidentally fall through the ventilation slots
into the cabinet-leading to fire, shock or equipment damage.
• Keep liquids away from the LCD monitor.
Spillage into the cabinet may result in fire, electric shock, or
equipment damage.
If an object or liquid falls/spills into the cabinet, unplug the LCD
monitor immediately. Have the unit checked by a qualified
service engineer before using it again.
• Do not touch a damaged LCD panel directly with bare
hands.
Use protective gloves whenever handling a damaged panel. The
liquid crystal which leaks from the panel is poisonous if it enters
the eyes or mouth. If any part of the skin or body comes in direct
contact with the panel, please wash thoroughly. If some physical
symptoms result, please consult your doctor.
• Take care in disposing of the LCD monitor.
The backlight of the LCD monitor contains mercury. Follow
local regulations or laws for safe disposal.
• Use the enclosed power cord. If using the power cord
other than the enclosed one, use the following cord.
In USA and Canada, use a UL LISTED/CSA LABELED or
CERTIFIED power cord set meeting the following specifications:
* Rating:
* Type:
min. 125 V, 10 A
SVT
* Length: max. 2.0 m
* Plug type: NEMA 5-15P, Parallel blade, Grounding type,
125 V, 10 A
In Europe, use a proper European standard approved power cord
meeting the following specifications:
* Rating:
* Type:
min. 250 V, 10 A
* Length: max. 2.0 m
H05VV-F 3G 1 mm2
Use a plug type approved by the country where you use
Failure to do so may cause fire or electric shock.
PRECAUTIONS
5
• The equipment must be connected to a grounded main
outlet.
Failure to do this may result in an electric shock.
• Handle the power cord with care.
* Do not place the cord underneath the LCD monitor or other
heavy objects.
* Do not pull on the cord.
* Do not bend, bundle or tie up the cord.
* Never attempt to repair a damaged cord.
If the power cord becomes damaged, stop using it. Use of a
damaged cord may result in fire or electric shock.
• To disconnect the power cord, grasp the plug firmly and
pull.
Never tug on the cord, doing so may cause damage and could
result in fire or electric shock.
• Use the correct voltage.
OK
The LCD monitor is designed for use with a specific voltage only.
Connection to a different voltage may cause fire, electric shock,
or other damage.
• Do not overload your power circuit, as this may result in
fire or electric shock.
• To ensure proper connections of the power cord, be
certain to plug the power cord into the provided LCD
monitor connector and directly to a wall outlet.
By not doing so may result in fire or electric shock.
• Keep the plastic packing bags away from children and
infants.
Plastic bags can be dangerous. To avoid danger of suffocation,
keep the bag away from babies and children.
• Place the LCD monitor on a strong, stable surface.
A unit placed on an inadequate surface may fall, resulting in
injury or equipment damage.
If the LCD monitor falls, disconnect the power immediately and
have the unit checked by a qualified service engineer before using
it again. Using a LCD monitor after it has been dropped may
result in fire or electric shock.
OK
• When attaching the monitor to the mount, use the
enclosed screws and tighten them securely. When
reattaching the monitor to the tilt stand, use the screws
that was attached to the monitor originally.
By not doing so may result in injury or failure of the monitor. To
attach the mount to the monitor, please read the instruction
manual of the mount.
6
PRECAUTIONS
• Set the LCD monitor in an appropriate location.
* Do not install in a dusty or humid environment.
E
* Do not place near water.
* Do not place in a location where light shines directly on the
screen.
* Do not place near heat generating devices or a humidifier.
CAUTION
• At the end of the day, or if you plan to leave the LCD
monitor unused for an extended period, turn off the main
power switch and disconnect the power cord from the wall
socket so that no power connections are made.
• To ensure safety, always unplug the LCD monitor before
cleaning it.
Cleaning the LCD monitor while it is plugged into a power
outlet may result in electric shock.
• Never use thinner, benzene, or other strong solvents or
abrasive cleaners, as these may cause damage to the
cabinet or LCD panel.
• Periodically clean the area around the plug.
Build-up of dust, water, or oil on the plug may result in fire.
• Please keep the LCD monitor in a dust-free environment.
Dust accumulation within the LCD monitor may result in fire or
equipment failure.
• Do not touch the plug or the power unit with wet hands.
Touching the plug with wet hands is dangerous and can cause
electrical shock.
• When handling the LCD monitor, please refer to the
diagram.
Grip the bottom of the LCD monitor firmly with both hands
ensuring the panel faces outward before lifting.
• Handle with care to avoid scratching or damaging the panel.
OK
If the LCD monitor becomes damaged, disconnect the power
immediately and have the unit checked by a qualified service
engineer before using it again. Using a LCD monitor after it has
been dropped may result in fire or electric shock.
• Disconnect the power cord when moving the LCD monitor.
Moving the LCD monitor with the cord attached or lifting it is
dangerous. It may result in injury or equipment damage.
• Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in
case of a problem.
PRECAUTIONS
7
• Do not block the ventilation slots on the cabinet.
* Do not place books or any other papers on the ventilation slots.
* Do not install the monitor in a closed space.
* Do not use the monitor laying down or upside down.
* Do not remove the tilt-swivel stand.
Using the monitor in this way blocks the ventilation slots
and prevents proper airflow, leading to fire or other damage.
Others
• The screen may have some defective pixels. These pixels
may appear as slightly light or dark areas on the screen.
This is due to the characteristics of the panel itself, and not
the LCD product.
• The backlight of the LCD monitor has a fixed life span.
When the screen becomes dark or begins to flicker, please contact
your dealer.
• Take care when handling the LCD panel.
* Do not press on the panel or edge of the frame strongly
as this will result in damage to the screen. There will be prints
left on the screen if the pressed image is dark or black. Leave the
screen white to decrease the prints.
* Do not scratch or press on the panel with any sharp objects, such
as pencil or pen as this may result in damage to the panel.
* Cleaning the panel with a dirty or rough cloth may damage the
panel.
• Generally, for maximum viewing comfort position the LCD
monitor slightly below eye level. Staring at the LCD monitor for
prolonged periods can cause eye strain. Be sure to take adequate
rests. (A 10-minute rest period each hour is suggested.)
8
PRECAUTIONS
INTRODUCTION
AboutThis Manual
E
This manual explains the precautions, features, specifications, and
operation of your EIZO LCD monitor. For convenience, a
“ScreenManager Quick Reference” guide has been included which shows
how to implement basic adjustments with the ScreenManager utility.
Package Contents
4 of 4 mm x 16 mm
mounting screws
LCD Monitor
Signal Cable
(MD-C87/100)
Power Cord
EIZO LCD Utility Disk
(for Windows®/Dos/
Macintosh)
User’s Manual
ScreenManager
Quick Reference
Warranty
Registration
Card
•
•
If any of the above-listed items are missing or damaged, please contact
your local dealer for assistance.
We recommend that you retain the original packing materials in case of
future need.
INTRODUCTION
9
Controls & Connectors
Viewing Angles
Horizontal: 140°
Vertical:
120°
Front
Auto Adjustment Button
Automatically centers the displayed
image and adjust clock and phase.
Control Buttons
The four control buttons (up, down, right
and left buttons) are used to enter
adjustments and settings when using the
ScreenManager menu.
Power Indicator
Indicates the power-on status in the
following ways:
Green (Solid): Power is ON
(normal mode)
(Flashing): Power is switching off in
15 minutes. (See page 27.)
Yellow(Solid): Power Saving Mode
(Flashing): Off Timer Mode
(See page 27.)
Enter Button
Power Switch
Rear
4 Holes for Mounting an Arm-Stand
Power Connector
Use the supplied power cord only.
D-Sub mini 15 pin Input Connector
Security Lock
Allows for connection of a security cable.
This lock supports the Kensington’s
MicroSaver security system. For further
information, please consult below.
Kensington Technology Group
2855 Campus Drive, San Mateo, CA
USA 94403
800-650-4242, x3348
Intl: 650-572-2700, x3348
Fax: 650-572-9675
10
INTRODUCTION
1 INSTALLATION
1-1 Connecting up
E
PC Settings
Before connecting your PC to the LCD monitor, change the display screen
settings (resolution and frequency) in accordance with those below.
Resolution and Frequency
fH: 31 kHz-61 kHz
fV: 50 Hz-75 Hz
• The following 4 common display modes are preset in the LCD
monitor's memory. If the display mode input to the LCD monitor is
not one of the modes listed below, a part of the image may be
distorted or missing.
Mode
Displayed Size
1024 x 768
1
2
640 x 480 (-75 Hz)
720 x 400 (70 Hz)
{320 x 200 (70 Hz)}
1024 x 768
3
4
800 x 600 (-75 Hz)
1024 x 768 (-75 Hz)
1024 x 768
1024 x 768
• The maximum resolution of this LCD monitor is 1024 x 768 at a
maximum fV of 75 Hz.
• The LCD monitor automatically enlarges lower display modes to the
maximum display modes (1024 x 768).
• The display modes, 720 x 400 and 320 x 200, have the same signal
timings. Select the appropriate resolution at “VGA Selection” to avoid
picture's distortion. See page 28.
• At the lower display modes, since the pixel elements are fixed, some
lines of the characters may become fuzzy. Use “Smoothing” to make
the lines clear. See page 23.
Using the LCD monitor withWindows® 95/98/2000
A Monitor information file is saved in the EIZO LCD Utility Disk
included in the package. It includes all the L350 required information
for best operation with Windows 95/98/2000. Please install the enclosed
utility and select “EIZO FlexScan L350” from the monitor list in Windows
95/98/2000.
For installation procedure, please read the readme.txt in the utilily disk.
1
INSTALLATION
11
Connecting the Cables
(1)Be sure that the power switches of both the PC and the LCD monitor
are OFF.
(2)Plug the signal cable into the D-Sub connector at the rear of the
monitor. Please ensure that the arrow mark on the casing of the
connector is visible when connecting.
When connecting the signal cable, check that the shape of the cable
connector matches the shape on the LCD monitor.
(3)Plug the other end of the cable into the video connector on the rear of
the PC.
Standard PC graphics board
D-Sub
mini 15 pin
D-Sub
mini 15 pin
Standard PC
graphics board
Signal Cable (enclosed)
Macintosh
D-Sub
mini 15 pin
D-Sub
mini 15 pin
Macintosh
(Blue & White)
Signal Cable (enclosed)
D-Sub
D-Sub 15 pin
mini 15 pin
D-Sub
mini 15 pin
Macintosh
Signal Cable (enclosed)
Macintosh Adapter DSCR-153 (optional)
(4) Plug the power cord into the power connector in the rear of the LCD
monitor. Plug the other end into a power outlet.
(5)Turn on the monitor’s main power and then switch on the PC power.
Whenever you finish your operation, turn off the PC and the monitor.
•
Do your part to conserve energy, turn off the monitor when you
are finished using it.
1
INSTALLATION
12
Attaching an Arm Stand to the Monitor
E
WARNING
•
When attaching the monitor to the mount, use the enclosed screws
and tighten them securely. When reattaching the monitor to the tilt
stand, use the screws that was attached to the monitor originally.
By not doing so may result in injury or failure of the monitor. To attach the
mount to the monitor, please read the instruction manual of the mount.
•
•
Use a VESA approved arm-stand. The LCD
75 mm
panel requires 75 mm x 75 mm hole spacing on
x
the arm mounting pad. The arm-stand should
75 mm
be able to support an object weighing 8.0 kg.
In case of using this LCD monitor with an
arm-stand in an office workspace, the arm-
stand shall be chosen and used carefully:
- Use only an approved arm-stand (e.g. GS).
- The arm-stand shall have sufficient stability
(mechanical firmness) to support the weight
of the monitor.
- The arm-stand shall remain in that position
where it is manually moved.
- The arm-stand shall have the ability to tilt
the monitor forward and backward.
500 mm
- The height of the upper row shall be less
than or equal to 500 mm in relation to the
desk surface when the arm-stnad is in its
(Example)
lowest osition.
(1)Lay the LCD monitor down as shown below, not scratching the panel.
Remove the tilt loosening the screws. When re-attaching the tilt, use
the enclosed screws and fix the tilt to the monitor securely.
Soft Cloth or
Cushion
(2)Place and fix a mount or an arm-stand to the monitor securely.
4 Mounting
Screws
(enclosed):
4x16 (mm)
1
INSTALLATION
13
2 USING THE SCREENMANAGER
2-1 How to use the ScreenManager
About ScreenManager
As shown on the display, the ScreenManager is used to adjust the LCD
monitor. Adjustments are made using the Enter and Control buttons (up,
down, right and left) located on the front panel.
Enter Button
Control Buttons
ScreenManager Menus
ScreenManager consists of a main menu and six sub menus: “Screen”,
“Color”, “PowerManager”, “Others”, “Information” and “Language.”
Animated icons on each menu allows for easy adjustment.
Main menu
•
The menu message for the ScreenManager can be displayed in six
languages: English, German, French, Italian, Spanish and Swedish.
Primary setting is English. For details, please refer to the next page.
2
USING THE SCREENMANAGER
14
Sub menus
E
Functions
<Screen>
Menus
Reference
page 18
page 24
page 26
page 27
<Color>
<PowerManager>
<Others>
<Information>
This menu shows the current ScreenManager
settings. The menu contains two pages.
Pressing the Enter key displays the following
information:
• Page 1: Input Signal
• Page 2: “Color” adjustment settings,
“PowerManager” settings,
“Others” menu settings
<Language>
First select the preferred language to use.
The ScreenManager’s messages will appear
in the selected language. This will become
the default language when you use the
ScreenManager.
15
2
USING THE SCREENMANAGER
How to use the ScreenManager
Entering the ScreenManager
Push the Enter button once to display the main menu of the
ScreenManager.
Enter the Settings
(1)To enter any sub menu icon, highlight the desired icon by using the
Control buttons (up, down, right and left) and push the Enter button.
The sub menu appears.
(2)Use the Control buttons to select the desired setting icon and push the
Enter button.
(3)The setting menu appears. Use the Control buttons to make all
required adjustments.
Exit the ScreenManager
(1)To return to the main menu, select the “Return” icon or push the
down button twice, followed by the Enter button.
(2)To save and exit the ScreenManager, select the “Exit” icon and push
the Enter button. Double clicking the Enter button at any time also
exits the ScreenManager menu.
•
Leaving the ScreenManager idle for 45 seconds or more will turn the
adjustment off automatically, without the adjustment's being saved.
2
USING THE SCREENMANAGER
16
Shortcut keys
E
Brightness and contrast can be adjusted directly without any need to
enter the ScreenManager. Press the Control buttons to adjust the settings
and then the Enter button to save all changes.
See the diagram below for adjustment directions.
The brightness and contrast functions are also available in the
ScreenManager “Screen” menu.
Brightness
up
Contrast
Contrast
down
up
Brightness
down
Adjustment Lock
Auto Adjustment button
Power Switch
The ScreenManager operation can be disabled by holding down the Auto
adjustment button while switching on the LCD monitor’s power. This
will disable (“lock”) the Enter button and Auto adjustment button,
protecting from accidental changes. To unlock the buttons, switch the
power off. Switch the power on while pressing the Auto adjustment
button.
Note the brightness and contrast can be adjusted using the shortcut keys
even while the Enter button is locked. After making such an adjustment,
the Enter button can be used to clear the brightness/contrast adjustment
menu from the screen.
17
2
USING THE SCREENMANAGER
2-2 Screen Adjustment
“Screen” adjustments for the LCD monitor should be used in suppressing
screen flickering and also for adjusting the screen to its proper position.
There is only one correct position for each display mode. It is also
recommended to use the ScreenManager function when first installing
the display or whenever changing the system.
For convenience, an easy set-up Program installed on the utility disk to
assist in the set-up procedure is provided.
Adjustment Procedure
Overview
(1) Install and run the "Screen Adjustment Program"
in the utility disk.
(2) Push the Auto adjustment button.
(3) Enter the ScreenManager and select the
"Screen" menu.
(4)
"Clock" adjustment
OK
"Phase" adjustment
Horizontal bars appear.
(5)
(6)
"Position" adjustment
(7) Confirm the "Resolution". (The "Screen
Adjustment program" shows "Resolution", but this
LCD monitor does not provide the adjustment.
Skip this adjustment.)
(8)
"Contrast/Brightness" adjustment
(9) Exit the ScreenManager.
2
USING THE SCREENMANAGER
18
E
•
•
•
Allow the LCD monitor to warm up for at least 20 minutes before making
adjustments.
For maximum viewing comfort, it is suggested that the monitor be tilted to
eye level.
To make adjustment easily, install and run the“Screen Adjustment
Program” in the attached utility disk. Before adjustment, read the
“readme.txt” file.
•
Do not continuously press the Control buttons (up, down, right and left
buttons) on the front panel, as the adjustment value will change quickly
and make it difficult to locate the most suitable adjustment point.
Procedure
Please adjust the screen using the following procedure.
(1)Having read the “readme.txt” file, install and run the “Screen
Adjustment Program” in the utility disk.
Step by step adjustment is provided by the wizard guide. Follow the
wizard or the procedures (2) to (7) below.
•
If the user's operation system has no utility disk (e.g. OS/2), we
recommend setting the desktop pattern to that as shown in the
diagram below.
Every-other-dot pattern
(2) Auto Adjustment
Push the Auto adjustment button on the front panel. The following
message will appear and remain on the screen for 5 seconds. While
the message is on the screen, push the button again to automatically
adjust the screen position. If you do not wish to do adjust the screen,
do not push the button again. The message will disappear.
•
The Auto adjustment function is intended for use on Macintosh and
PCs running Windows. It may not function properly if any of the
following applies:
19
2
USING THE SCREENMANAGER
•
•
PC running MS-DOS (not Windows).
The background color for the “wallpaper” or “desktop” pattern is
set to black or dark.
•
Some signals from some graphics boards may not function
properly. Follow the adjustment procedure next page.
•
During the Auto adjustment, some icons (e.g. clock icon) appear
on the screen continuously.
(Example)
(3) Enter the ScreenManager “Screen” menu.
(4) “Clock” Adjustment
Function
Decreases the vertical bars of distortion.
a) Select the “Clock” icon and push the Enter button
to enter the “Clock” menu.
b) If horizontal bars appear, these can be eliminated
by adjusting the right and left buttons.
c) Press the Enter button to memorize the setting
and return to the “Screen” menu.
i) If the screen is free from any bars of distortion,
proceed to “Position” adjustment.
ii)If horizontal flickering or horizontal bars
appear, proceed to “Phase” adjustment.
· The LCD monitor is designed for analog input
signals from a standard graphics board. The
analog input signal is converted to a digital signal
by the LCD circuitry. To convert the signal
correctly, the LCD monitor needs to produce the
same number of clock pulses as the dot clock of
the graphics system. When the clock pulse is not
correctly set, some vertical bars of distortion are
displayed on the screen.
· When adjusting the “Clock”, the horizontal screen
size will also change.
2
USING THE SCREENMANAGER
20
(5) “Phase” Adjustment
Function
E
Eliminates the horizontal bars of distortion.
a) Select the “Phase” icon and push the Enter button
to show the “Phase” menu.
b)If horizontal bars appear, these can be eliminated
by adjusting the right and left buttons.
c) After finishing the adjustment, push the Enter
button to memorize the settings and return to the
“Screen” menu.
· “Phase” adjustments should be done after
adjusting the “Clock”.
· Horizontal bars may not completely disappear
from the screen depending on the PC.
· The phase adjustment decides the sampling point
for converting the analog input signal to a digital
signal. Adjusting the “Phase” after the “Clock”
adjustment will produce a clear screen.
(6) “Position” Adjusment
Function
Controls the screen position.
a) Select the “Position” icon and push the Enter
button to enter the “Position menu. Adjustment
markers are displayed on each corner of the
screen.
b)Adjust the position of th eupper left corner of the
image using the Control buttons in order to align
the screen.
· If vertical bars of distortion appear after finishing
the “Position” adjustment, return to “Clock” menu
and repeat the previously explained adjustment
procedure (“Clock” “Phase” “Position”).
c) After finishing the adjustment, push the Enter
button to memorize the settings and return to the
“Screen” menu.
21
2
USING THE SCREENMANAGER
(7) “Contrast” Adjustment
Function
Controls the contrast of the screen.
a) Select the “Contrast” icon and push the Enter
button to show the “Contrast/Brightness” menu.
b) Press the Auto adjustment button on the front
panel while displaying the “Contrast/Brightness
menu to automatically adjust contrast.
c) The screen blanks for a moment and adjusts the
contrast to the maximum level of the current
input signal.
OK
Too High
Too Low
* In the case of the percentage color flickering
between yellow and white, please note that
this is not an error but actually the most
optimum adjustment point.
* The brightness of the entire screen is con-
trolled by changing the “Brightness” controls.
No contrast adjustment is required except when
the graphics board or the resolution is changed
from the previous one.
d) Adjust the “Brightness” as desired using the up
and down buttons.
e) After finishing the adjustment, push the Enter
button to memorize the settings and return to the
“Screen” menu.
(8) Exit the ScreenManager
a) To return to the main menu, select the “Return” icon or push the
down button twice, followed by the Enter button.
b) To exit the ScreenManager, select the “Exit” icon and push the
Enter button. Double clicking the Enter button at any time also
exit the ScreenManager menu.
This is the end of the Screen adjustment procedure.
2
USING THE SCREENMANAGER
22
E
•
At the lower display modes (refer to the page 11), the following
adjustment is available.
Function
Displays blurred texts clearly.
Smoothing
· This adjustment does not operate when the
resolution is 1024 x 768.
23
2
USING THE SCREENMANAGER
2-3 Color Adjustment
About Color Adjustments
Entering the ScreenManager, select the “Color” icon and push the enter
button to show the “Color” menu.
The ScreenManager “Color” menu provides 3 color setting modes; 1, 2,
and 3. You can also adjust the color settings for each mode and store
them for future use.
•
Allow the monitor to warm-up for at least 20 minutes before making
an adjustment.
Color Mode
Function
Color Mode
(Standard)
Adjusts:
Color Mode
Mode 1(default): The normal white color. It is
the maximum contrast level.
Please use this mode normally.
Mode 2:
Mode 3:
The white color tone is
slightly bluish.
The white color tone is
slightly reddish.
· The contrast level is reduced in Mode 2 and 3.
(a) Select the “Color Mode” icon from the “Color”
menu and push the Enter button.
(b) Select option 1, 2 or 3 and push the Enter
button. A long beep will be heard indicating the
adjustment settings have been saved.
2
USING THE SCREENMANAGER
24
Gain Adjustments
E
By adjusting the red, green and blue color tones for each mode, custom
colors can be defined. Please use this function when high precision color
adjustment is required.
•
Before you attempt to change the colors, always start with the color
settings set to the default setting by using the “Reset” icon in each
color mode.
Function
Gain
Adjusts:
Gain
Gain
The Gain adjustment has no effect on the starting
point (the black level). It changes only the ending
point (the white level). The Gain adjustment is
used to fine tune the whites and light grays to an
even balance.
a) Select the “Gain” icon. The screen shown on the
left will appear.
b) Adjust each color until you can create a uniform
white screen.
c) To register the adjustment, select the “Save” icon
and then push the Enter button. If the settings
are not saved, all adjustments will be lost.
d) Finally, re-adjust the contrast in the “Screen”
menu to get the best image clarity.
· The adjustment works effectively only when the
percentages appear black. Magenta percentage
means the color’s saturation. Lower the
percentage until it becomes black.
· After making the color settings, re-adjust the
contrast to get the best definition and color
intensity for the displayed image.
· “Reset”
You can recall the default color gain setting for
the current color mode (1, 2, 3) using the “Reset”
icon.
· The values shown in percentages represent the
current level within the specific adjustment only.
They are available only as a reference tool. (To
create a uniform white or black screen, the
percentages for each will probably not be the
same.)
2
USING THE SCREENMANAGER
25
2-4 Power-save Setup
Function
PowerManager
Power saving adjustment
The EIZO PowerManager functions comply with
the VESA DPMS standard
As an Energy Star® Partner, Eizo
Nanao Corporation has determined
that this product meets the Energy Star
guidelines for energy efficiency.
· Do your part to conserve energy, turn off the
monitor when you are finished using it.
Disconnecting the monitor from the power supply
is recommended to save energy completely.
Set-up Procedure
Set the monitor’s power saving environment to match the PC’s
ScreenSaver software.
•
For the PC setup, please refer to the user’s manuals of the PC and
the graphics board.
VESA DPMS Power Saving Method
VESA DPMS utilizes four signals: ON, STANDBY, SUSPEND, and OFF.
The monitor detects these signals from the graphics board and executes
power saving accordingly, as illustrated below.
Signal
Screen
Indicator
Power Consumption
ON
Operation
Blank
Green
35 W
STAND-BY,
Yellow
less than 3 W
SUSPEND, OFF
What is VESA DPMS?
The acronym VESA stands for “Video Electronics Standards
Association,” and DPMS stands for “Display Power Management
Signaling.” DPMS is a communication standard that PCs and
graphics boards use to implement power savings at the monitor side.
What is Energy Star?
“Energy Star” is a set of power-saving guidelines issued by the U.S.
Environmental Protection Agency (EPA). The guidelines apply to PC
systems and peripherals.
2
USING THE SCREENMANAGER
26
2-5 Other Settings
E
All of the icons shown in the ScreenManager “Others” menu are
described below.
Function
Automatically Turns off the Monitor
Off Timer
What is Off Timer
The Off Timer function allows the user to set the
time in which the monitor will be in operation,
called the “On Period” and automatically shifts the
operation into the “Power Off” mode when the set
“On Period” expires. The Off Timer function was
created to reduce after-image characteristics that are
particular to LCD monitors when the monitor
screen is left on for a long period without use.
1) Select the “Off Timer” icon and press the Enter
button to display “Off Timer” select menu.
2) Select “Enable” and press the Enter button.
3) Press the right/left button to adjust how long (1 to
23 hours) the monitor should be in the “On
Period”. Then, press the enter button to return to
the “others” menu.
Advance notice (indicator; flashing green) will be
given 15 minutes before the monitor will automati-
cally turn off and enter the “Power Off” modes .
To Delay Entering Power Off
To delay entering the “Power Off” mode, press any
button on the front panel located to the left of the
LED light during the advance notice period. The
monitor will continue to operate for an additional
90 minutes. There will be another advance notice
for 15 minutes as described. Delayed entrance into
the “Power Off” period can be extended as many
times as desired.
·
The Off Timer function will work while
PowerManager is active, but there would be no
advance notice before the monitor's power
switches off.
27
2
USING THE SCREENMANAGER
Function
Selecting Appropriate VGA Mode
VGA Selection
The two display modes, VGA 720 x 400 (70 Hz) and
320 x 200 (70 Hz), have the same signal timings.
Using this adjustment selects the appropriate display
mode.
1) Select the “VGA Selection” icon and push the
Enter button to show the resolution select menu.
2) Select “Text 720 x 400” or “Graphics 320 x 200,
and push the Enter button.
·
This function effects only when the resolution is
VGA 720 x 400 (70 Hz) or 320 x 200 (70 Hz).
Adjusting Menu's Position
Menu Position
1) Select the “Menu Position” icon and push the
Enter button to show the menu position menu.
2) Set the position using the control buttons. Then,
push the Enter button to return to the Others
menu.
Returns the settings to Factory Default
Default setting are as follows:
Reset
Screen:
• Contrast:
• Brightness
• Smoothing
50%
100 %
3
Color
• Mode 1/Normal white
PowerManager • VESA DPMS
Others
• Off Timer:
Disable
Language
• English
2
USING THE SCREENMANAGER
28
3 TROUBLESHOOTING
This page presents problems that can be corrected by the user. If a
problem persists even after applying the suggested remedies, contact an
EIZO dealer.
E
T No picture
Problems
Points to check with possible solutions
1) Indicator status: OFF
2) Indicator status: GREEN
Check that the power cord is securely connected.
Check brightness and contrast settings. Minimum
settings will cause screen to be blank.
Try pressing the power switch. (The Off timer
may be active.)
3) Indicator status: YELLOW
(flashing)
Try pressing a key on the keyboard, or clicking the
mouse. (The screen-saver software may be active.)
4) Indicator status: YELLOW
If the problem persists, switch off the monitor
main power for a few minutes, then switch it back
on and try again.
5) “No signal detected” error
message appears.
Check that the PC is switched ON.
Check that the signal cable is properly connected
to the graphics board or PC.
Check that the graphics board is correctly inserted
in the PC.
For Windows 95/98/2000 users, install the “Monitor
information file” in the utility disk.
6) “Out of range” error
message appears.
Use the graphics board’s utility software to change
the frequency setting. (Refer to the manual of the
graphics board.)
(Example)
For Windows 95 users (OSR 2.0 or newer)/98,
restart the PC in a safe mode and change the
frequency at the “Display” setting in the PC.
• Whenever an error signal message appears, the signal frequency will be displayed
in red.
• Error messages will remain on the screen for 30 seconds, and then disappear. An
error message may not appear at all if the signal frequency is extremely high or
extremely low.
29
3
TROUBLESHOOTING
T Imaging problems
Problems
Points to check with possible solutions
1) Display position is incorrect.
Adjust the image position using the “Position” icon
in the ScreenManager “Screen” menu. See page 21.
If the problem persists, use the graphics board's
utility sofware to change the display position if
available. (It may be called “back-porch”.)
Change the resolution or refresh rate to match the
preset mode. See page 11.
2) Vertical bars of distortion
appear.
Decrease the vertical bars using the“Clock” icon in
the ScreenManager “Screen” menu. See page 20.
3) Letters and lines appear
blurred.
Adjust the blurred lines using “Smoothing”
adjustment. Please Refer to the page 23.
4) Distortion appears like the
figure below.
This happens when both composite (X-OR) input
signal and separate vertical synchronizing signal
are input. Please select either one from the two
signals.
5) Horizontal bars of distortion
appear.
Decrease the horizontal bars using the “Phase”
icon in the ScreenManager “Screen” menu. See
page 21.
6) The screen is too bright or
too dark.
Adjust the contrast and brightness using the
ScreenManager’s Screen menu. See page 22.
(The backlight of the LCD monitor has a fixed life
span. When the screen becomes dark or begins to
flicker, please contact your dealer.)
7) After-images appear.
When the screen image has been changed after
displaying the same image for a long period, after-
images may appear. Use the Off Timer function
and avoid leaving the screen on all the time.
8) Finger prints appears on the
screen.
Leaving the screen white may solve the problem.
3
TROUBLESHOOTING
30
Problems
Points to check with possible solutions
E
9) The screen has defective
pixels (e.g. slightly light or
dark).
This is due to the characteristics of the panel itself,
and not the LCD product.
TOthers
Problems
Points to check with possible solutions
1) The utility disk is unable to be
opened (for Macintosh only).
Some PCs without PC-Exchange do not allow the
utility disk to be opened. Please set the desktop
pattern to ever-other-dot before adjustment. See
page 19.
The adjustment lock is probably on. To unlock:
switch the LCD monitor off. Then, while pressing
the Auto adjustment button switch the power on.
See page 17.
2) • The Enter button does not
operate.
• The Auto adjustment
button does not operate.
The Auto adjustment function is intended for use
on Macintosh and IBM compatibles PCs running
Windows. It may not work properly if either of
the following applies.
3) The Auto adjustment button
does not work properly.
-
You are running an AT-compatible PC on MS-
DOS (not Windows).
-
The background color for the “wallpaper” or
“desktop” pattern is set to black.
Some signals from the graphics boards may not
function properly. Follow the adjustment
procedure on page 18, adjust step by step using
the “Screen” menu.
Use the graphics board’s utility software to change
the input signal frequency.
4) Frequency does not change
after installing “Monitor
information file” in the
attached utility disk on
Windows 95/98/2000.
31
3
TROUBLESHOOTING
4 CLEANING
WARNING
•
Keep liquids away from the monitor.
Spillage into the cabinet may result in fire, electric shock, or equip-
ment damage.
If an object or liquid falls/spills into the cabinet, unplug the monitor
immediately. Have the unit checked by a qualified service engineer
before using it again.
CAUTION
•
To ensure safety, always unplug the monitor before cleaning it.
Cleaning the monitor while it is plugged into a power outlet may
result in electric shock.
•
•
Periodically clean the area around the plug.
Buildup of dust, water, or oil on the plug may result in fire.
Dust accumulation within the monitor may result in fire or
equipment failure.
Please keep the monitor in a dust-free environment.
•
Never use thinner, benzene, alcohol (ethanol, methanol, or
isopropyl alcohol), abrasive cleaners, or other strong solvents,
as these may cause damage to the cabinet or LCD.
Periodic cleaning is recommended to keep the monitor looking new and
to prolong its operational lifetime. Clean the cabinet and LCD panel as
follows.
Cabinet
To remove stains, wipe the cabinet with a soft, lightly moistened cloth
using a mild detergent. Do not spray wax or cleaner directly onto the
cabinet.
LCD panel
The LCD surface can be cleaned with a soft cloth, such as cotton or lens
paper.
If necessary, stubborn stains can be removed by moistening part of a
cloth with water to enhance its cleaning power.
4
CLEANING
32
5 SPECIFICATIONS
Electrical Specifications
E
LCD Panel
38 cm (15 inch), TFT color LCD panel
0.297 mm dot pitch, Anti-Glare Hard Coating
Horizontal: 140°, Vertical: 120°
(at Contrast Ratio > 5)
Viewing Angle
Scan Frequency
Horizontal:
Vertical:
31 kHz-61 kHz (Automatic)
50 Hz-75 Hz (Automatic)
Viewable Image Size
304 mm (H) ´ 228 mm (V)(11.9” (H) ´ 8.9”(V))
(Viewable Image Size: 38.0 mm (14.9”))
100-120/220-240 VAC 10%, 50/60 Hz, 0,6/0.3 A
35 W
Less than 3 W
D-Sub mini 15-pin
Power Supply
Power Consumption:
Power Saving Mode:
Input Connector
Display Colors
16 million colors (max.)
Recommended Resolution 1024 dots ´ 768 lines
Input Signal
Sync:
• H/V Separate, TTL, Positive/Negative
• H/V Composite, TTL, Positive/Negative
• Analog 0.7 Vp-p/75 W, Positive
80 MHz
Video:
Pixel Dot Clock
Plug & Play
VESA DDC1/2B
Mechanical Specifications
Dimensions
384 mm (W) ´ 386.2 mm (H) ´171.4 mm (D)
(15.1” (W) ´ 15.2” (H) ´ 6.7” (D))
Weight
5.6 kg (12.3 lbs.)
Weight (without tilt stand) 4.1 kg (9.0 lbs.)
Environmental Specifications
Temperature
Operating: 0°C to 35°C (32°F to 95°F)
Storage: -20°C to 60°C (-4°F to 140°F)
Humidity
30% to 80% R.H. Non-condensing
Certifications and Standards
100-120 VAC range
UL/C-UL, FCC class B, TÜV Rheinland Ergonomics
Approved, TCO’99 (excluding black-cabinet L350),
EPA ENERGY STAR® Program
220-240 VAC range
CE, CB, TÜV Rheinland/GS, TÜV Rheinland/
Ergonomics Approved, TCO’99 (excluding black-
cabinet L350), EPA ENERGY STAR® Program, TÜV
Eco Circle 2000
33
5
SPECIFICATIONS
MEMO
5
SPECIFICATIONS
34
Excluding
Black-Cabinet
LCD Monitor
Congratulations!
You have just purchased a TCO’99 approved and labelled product! Your choice has
provided you with a product developed for professional use. Your purchase has also
contributed to reducing the burden on the environment and also to the further development
of environmentally adapted electronics products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for
encouraging the adaptation of goods and services to the environment. The main problem,
as far as computers and other electronics equipment are concerned, is that environmen-
tally harmful substances are used both in the products and during their manufacture.
Since it is not so far possible to satisfactorily recycle the majority of electronics equip-
ment, most of these potentially damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels,
that are important from the viewpoints of both the work (internal) and natural (external)
environments. Since all methods of electricity generation have a negative effect on the
environment (e.g. acidic and climate-influencing emissions, radioactive waste), it is vital
to save energy. Electronics equipment in offices is often left running continuously and
thereby consumes a lot of energy.
What does labelling involve?
This product meets the requirements for the TCO’99 scheme which provides for
international and environmental labelling of personal computers. The labelling scheme
was developed as a joint effort by the TCO (The Swedish Confederation of Professional
Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conserva-
tion) and Statens Energimyndighet (The Swedish National Energy Administration).
Approval requirements cover a wide range of issues: environment, ergonomics,
usability, emission of electric and magnetic fields, energy consumption and electrical and
fire safety.
The environmental demands impose restrictions on the presence and use of heavy
metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated
solvents, among other things. The product must be prepared for recycling and the
manufacturer is obliged to have an environmental policy which must be adhered to in
each country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a
certain period of inactivity, shall reduce its power consumption to a lower level in one or
more stages. The length of time to reactivate the computer shall be reasonable for the
user.
Labelled products must meet strict environmental demands, for example, in respect of
the reduction of electric and magnetic fields, physical and visual ergonomics and good
usability.
Below you will find a brief summary of the environmental requirements met by this
product. The complete environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): [email protected]
Current information regarding TCO’99 approved and labelled products may also be
Excluding
Black-Cabinet
LCD Monitor
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and
housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30%
of the plastic in a computer casing can consist of flame retardant substances. Most
flame retardants contain bromine or chloride, and those flame retardants are chemically
related to another group of environmental toxins, PCBs. Both the flame retardants
containing bromine or chloride and the PCBs are suspected of giving rise to severe
health effects, including reproductive damage in fish-eating birds and mammals, due to
the bio-accumulative* processes. Flame retardants have been found in human blood and
researchers fear that disturbances in foetus development may occur.
The relevant TCO’99 demand requires that plastic components weighing more than
25 grams must not contain flame retardants with organically bound bromine or
chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes
are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of
certain computer displays. Cadmium damages the nervous system and is toxic in high
doses. The relevant TCO’99 requirement states that batteries, the colour-generating
layers of display screens and the electrical or electronics components must not contain
any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous
system and is toxic in high doses. The relevant TCO’99 requirement states that batteries
may not contain any mercury. It also demands that mercury is not present in any of the
electrical or electronics components associated with the labelled unit.
CFCs (freons)
The relevant TCO’99 requirement states that neither CFCs nor HCFCs may be used
during the manufacture and assembly of the product. CFCs (freons) are sometimes used
for washing printed circuit boards. CFCs break down ozone and thereby damage the
ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light
with e.g. increased risks of skin cancer (malignant melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead
damages the nervous system and in higher doses, causes lead poisoning. The relevant
TCO’99 requirement permits the inclusion of lead since no replacement has yet been
developed.
* Bio-accumulative is defined as substances which accumulate within living
organisms.
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of conformity
We, the Responsible Party
EIZO NANAO Technologies Inc.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: FlexScan L350
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to
the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provided
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and receiver.
*Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
*Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep
interference within the limits of a Class B digital device.
-AC Cord
-Shielded Signal Cable (D-SUB mini 15 pin - D-SUB mini 15 pin, the enclosed signal cable)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
For Europe, etc. (220-240 Vac) Only
CE Marking
Declaration of Conformity
Kind of equipment:
Type-designation:
Monitor
L350
is in compliance with:
Council Directive 73/23/EEC
Council Directive 89/336/EEC
EN60950:1992+A1+A2+A3+A4+A11
EN55022 (classB):1995
EN61000-3-2:1995
EN55024:1998
EN61000-3-3:1995
Konformitätserklärung
Geräteart :
Gerätetyp :
Monitor
L350
den folgenden Normen oder Vorschriften entspricht:
EU-Richtlinie 73/23/EEC
EU-Richtlinie 89/336/EEC
EN60950:1992+A1+A2+A3+A4+A11
EN55022 (classB):1995
EN61000-3-2:1995
EN55024:1998
EN61000-3-3:1995
Déclaration de conformité
Nature de l’équipement :
Type-désignation :
Moniteur
L350
est en conformité avec :
Directive Européenne 73/23/EEC EN60950:1992+A1+A2+A3+A4+A11
Directive Européenne 89/336/EEC EN55022 (classB):1995
EN61000-3-2:1995
EN55024:1998
EN61000-3-3:1995
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1/59-98 mit dem
Videosignal, 1024 Punkte x 768 Zeilen, RGB analog, 0,7 Vp-p und mindestens 75,0 Hz
Bildwiederholfrequenz, non interlaced.
Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem
Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem
Zeichenkontrast.)
Recycle Auskunft
Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland
zusammen mit dem Partner von Roll MBB Recycling GmbH.
Dort werden die Geräte in ihre Bestandteile zerlegt, die dann der Wiederverwertung zugeführt
werden. Um einen Abholtermin zu vereinbaren und die aktuellen Kosten zu erfahren, benutzen
Sie bitte folgende Rufnummer: 02153-73 35 00. Weitere Informationen finden Sie auch unter
der Internet-Adresse: www.eizo.de.
|