CY7C1336H
PRELIMINARY
2-Mbit (64K x 32) Flow-Through Sync SRAM
Features
Functional Description[1]
The CY7C1336H is a 64K x 32 synchronous cache RAM
designed to interface with high-speed microprocessors with
minimum glue logic. Maximum access delay from clock rise is
6.5 ns (133-MHz version). A 2-bit on-chip counter captures the
first address in a burst and increments the address automati-
cally for the rest of the burst access. All synchronous inputs
are gated by registers controlled by a positive-edge-triggered
Clock Input (CLK). The synchronous inputs include all
addresses, all data inputs, address-pipelining Chip Enable
• 64K x 32 common I/O
• 3.3V core power supply
• 3.3V I/O supply
• Fast clock-to-output times
— 6.5 ns (133-MHz version)
— 8.0 ns (100-MHz version)
• Provide high-performance 2-1-1-1 access rate
(CE ), depth-expansion Chip Enables (CE and CE ), Burst
1
2
3
Control inputs (ADSC, ADSP,
ADV), Write Enables
and
®
• User-selectable burst counter supporting Intel
(BW
, and BWE), and Global Write (GW). Asynchronous
[A:D]
®
Pentium interleaved or linear burst sequences
• Separate processor and controller address strobes
• Synchronous self-timed write
inputs include the Output Enable (OE) and the ZZ pin.
The CY7C1336H allows either interleaved or linear burst
sequences, selected by the MODE input pin. A HIGH selects
an interleaved burst sequence, while a LOW selects a linear
burst sequence. Burst accesses can be initiated with the
Processor Address Strobe (ADSP) or the cache Controller
Address Strobe (ADSC) inputs. Address advancement is
controlled by the Address Advancement (ADV) input.
• Asynchronous output enable
• Supports 3.3V I/O level
• Offered in JEDEC-standard lead-free 100-pin TQFP
package
Addresses and chip enables are registered at rising edge of
clock when either Address Strobe Processor (ADSP) or
Address Strobe Controller (ADSC) are active. Subsequent
burst addresses can be internally generated as controlled by
the Advance pin (ADV).
• “ZZ” Sleep Mode option
The CY7C1336H operates from a +3.3V core power supply
while all outputs may operate with a +3.3V supply. All inputs
and outputs are JEDEC-standard JESD8-5-compatible.
Logic Block Diagram
ADDRESS
REGISTER
A0, A1, A
A[1:0]
MODE
ADV
CLK
Q1
BURST
COUNTER
AND LOGIC
Q0
CLR
ADSC
ADSP
DQD
BYTE
DQD
BWD
BYTE
WRITE REGISTER
WRITE REGISTER
DQC
BYTE
DQC
BYTE
BWC
WRITE REGISTER
OUTPUT
BUFFERS
DQs
WRITE REGISTER
MEMORY
ARRAY
SENSE
AMPS
DQB
BYTE
DQB
BYTE
BWB
WRITE REGISTER
WRITE REGISTER
DQA
BYTE
DQA
BYTE
BWA
BWE
WRITE REGISTER
WRITE REGISTER
INPUT
REGISTERS
GW
ENABLE
REGISTER
CE1
CE2
CE3
OE
SLEEP
CONTROL
ZZ
Note:
1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
Cypress Semiconductor Corporation
Document #: 001-00210 Rev. *A
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised February 6, 2006
PRELIMINARY
CY7C1336H
Pin Definitions
Name
I/O
Description
Address Inputs used to select one of the 64K address locations. Sampled at the rising edge of the
feed the 2-bit
A0, A1,
A
Input-
Synchronous CLK if ADSP or ADSC is active LOW, and CE , CE , and CE are sampled active. A
1
2
3
[1:0]
counter.
Byte Write Select Inputs, active LOW. Qualified with BWE to conduct Byte Writes to the SRAM.
Synchronous Sampled on the rising edge of CLK.
BW ,
Input-
A
BW
B
BW ,
C
BW
D
GW
Input-
Global Write Enable Input, active LOW. When asserted LOW on the rising edge of CLK, a global
Synchronous Write is conducted (ALL bytes are written, regardless of the values on BW
and BWE).
[A:D]
BWE
CLK
Input-
Byte Write Enable Input, active LOW. Sampled on the rising edge of CLK. This signal must be
Synchronous asserted LOW to conduct a Byte Write.
Input-Clock Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the burst
counter when ADV is asserted LOW, during a burst operation.
CE
Input-
Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE
2
1
Synchronous and CE to select/deselect the device. ADSP is ignored if CE is HIGH. CE is sampled only when a
3
1
1
new external address is loaded.
CE
CE
Input-
Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with CE
1
2
Synchronous and CE to select/deselect the device. CE
is sampled only when a new external address is loaded.
3
2
Input-
Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE
1
3
Synchronous and CE to select/deselect the device. CE is sampled only when a new external address is loaded.
2
3
OE
Input-
Output Enable, asynchronous input, active LOW. Controls the direction of the I/O pins. When LOW,
Asynchronous the I/O pins behave as outputs. When deasserted HIGH, I/O pins are tri-stated, and act as input data
pins. OE is masked during the first clock of a Read cycle when emerging from a deselected state.
ADV
Input-
Advance Input signal, sampled on the rising edge of CLK. When asserted, it automatically incre-
Synchronous ments the address in a burst cycle.
ADSP
Input-
Address Strobe from Processor, sampled on the rising edge of CLK, active LOW. When asserted
Synchronous LOW, addresses presented to the device are captured in the address registers. A
are also loaded
[1:0]
into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP is
ignored when CE
is deasserted HIGH
1
ADSC
ZZ
Input-
Address Strobe from Controller, sampled on the rising edge of CLK, active LOW. When asserted
are also loaded
into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized.
Synchronous LOW, addresses presented to the device are captured in the address registers. A
[1:0]
Input-
ZZ “sleep” Input, active HIGH. When asserted HIGH places the device in a non-time-critical “sleep”
Asynchronous condition with data integrity preserved. For normal operation, this pin has to be LOW or left floating.
ZZ pin has an internal pull-down.
DQs
I/O-
Bidirectional Data I/O lines. As inputs, they feed into an on-chip data register that is triggered by the
Synchronous rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by the
addresses presented during the previous clock rise of the Read cycle. The direction of the pins is
controlled by OE. When OE is asserted LOW, the pins behave as outputs. When HIGH, DQs are placed
in a tri-state condition.
V
Power
Supply
Power supply inputs to the core of the device.
DD
V
V
Ground
Ground for the core of the device.
SS
I/O Power
Supply
Power supply for the I/O circuitry.
DDQ
V
I/O Ground Ground for the I/O circuitry.
SSQ
MODE
Input-
Static
Selects Burst Order. When tied to GND selects linear burst sequence. When tied to V or left floating
DD
selects interleaved burst sequence. This is a strap pin and should remain static during device operation.
Mode Pin has an internal pull-up.
NC
No Connects. Not Internally connected to the die. 4M, 9M, 18M, 72M, 144M, 288M, 576M, and 1G are
address expansion pins and are not internally connected to the die.
Document #: 001-00210 Rev. *A
Page 3 of 15
PRELIMINARY
CY7C1336H
indicate a write access. ADSC is ignored if ADSP is active
LOW.
Functional Overview
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. Maximum access delay from
The addresses presented are loaded into the address register
and the burst counter/control logic and delivered to the
the clock rise (t
) is 6.5 ns (133-MHz device).
CDV
memory core. The information presented to DQ
will be
[D:A]
The CY7C1336H supports secondary cache in systems
utilizing either a linear or interleaved burst sequence. The
interleaved burst order supports Pentium and i486™
processors. The linear burst sequence is suited for processors
that utilize a linear burst sequence. The burst order is
user-selectable, and is determined by sampling the MODE
input. Accesses can be initiated with either the Processor
Address Strobe (ADSP) or the Controller Address Strobe
(ADSC). Address advancement through the burst sequence is
controlled by the ADV input. A two-bit on-chip wraparound
burst counter captures the first address in a burst sequence
and automatically increments the address for the rest of the
burst access.
written into the specified address location. Byte Writes are
allowed. During Byte Writes, BW controls DQ , BW controls
A
A
B
DQ , BW controls DQ , and BW controls DQ . All I/Os are
B
C
C
D
D
tri-stated when a Write is detected, even a Byte Write. Since
this is a common I/O device, the asynchronous OE input signal
must be deasserted and the I/Os must be tri-stated prior to the
presentation of data to DQs. As a safety precaution, the data
lines are tri-stated once a Write cycle is detected, regardless
of the state of OE.
Burst Sequences
The CY7C1336H provides an on-chip two-bit wraparound
burst counter inside the SRAM. The burst counter is fed by
A
, and can follow either a linear or interleaved burst order.
Byte Write operations are qualified with the Byte Write Enable
[1:0]
The burst order is determined by the state of the MODE input.
A LOW on MODE will select a linear burst sequence. A HIGH
on MODE will select an interleaved burst order. Leaving
MODE unconnected will cause the device to default to a inter-
leaved burst sequence.
(BW ) and Byte Write Select (BW
) inputs. A Global Write
E
[A:D]
Enable (GW) overrides all Byte Write inputs and writes data to
all four bytes. All Writes are simplified with on-chip
synchronous self-timed write circuitry.
Three synchronous Chip Selects (CE , CE , CE ) and an
1
2
3
asynchronous Output Enable (OE) provide for easy bank
Sleep Mode
selection and output tri-state control. ADSP is ignored if CE
1
The ZZ input pin is an asynchronous input. Asserting ZZ
places the SRAM in a power conservation “sleep” mode. Two
clock cycles are required to enter into or exit from this “sleep”
mode. While in this mode, data integrity is guaranteed.
Accesses pending when entering the “sleep” mode are not
considered valid nor is the completion of the operation
guaranteed. The device must be deselected prior to entering
the “sleep” mode. CEs, ADSP, and ADSC must remain
is HIGH.
Single Read Accesses
A single read access is initiated when the following conditions
are satisfied at clock rise: (1) CE , CE , and CE are all
asserted active, and (2) ADSP or ADSC is asserted LOW (if
the access is initiated by ADSC, the write inputs must be
deasserted during this first cycle). The address presented to
the address inputs is latched into the address register and the
burst counter/control logic and presented to the memory core.
If the OE input is asserted LOW, the requested data will be
1
2
3
inactive for the duration of t
LOW.
after the ZZ input returns
ZZREC
Interleaved Burst Address Table
(MODE = Floating or VDD
available at the data outputs a maximum to t
rise. ADSP is ignored if CE is HIGH.
after clock
CDV
)
1
First
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
Single Write Accesses Initiated by ADSP
Address
A1, A0
This access is initiated when the following conditions are
satisfied at clock rise: (1) CE , CE , CE are all asserted
1
2
3
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
active, and (2) ADSP is asserted LOW. The addresses
presented are loaded into the address register and the burst
inputs (GW, BW , and BW
) are ignored during this first
E
[A:D]
clock cycle. If the Write inputs are asserted active (see Write
Cycle Descriptions table for appropriate states that indicate a
Write) on the next clock rise, the appropriate data will be
latched and written into the device. Byte Writes are allowed.
Linear Burst Address Table (MODE = GND)
During Byte Writes, BW controls DQ and BW controls
A
A
B
First
Second
Third
Fourth
DQ , BW controls DQ , and BW controls DQ . All I/Os are
B
C
C
D
D
Address
Address
Address
Address
tri-stated during a Byte Write. Since this is a common I/O
device, the asynchronous OE input signal must be deasserted
and the I/Os must be tri-stated prior to the presentation of data
to DQs. As a safety precaution, the data lines are tri-stated
once a Write cycle is detected, regardless of the state of OE.
A ,A
A ,A
A ,A
A ,A
1
0
1
0
1
0
1
0
00
01
10
11
01
10
11
10
11
00
11
00
01
00
01
10
Single Write Accesses Initiated by ADSC
This write access is initiated when the following conditions are
satisfied at clock rise: (1) CE , CE , and CE are all asserted
1
2
3
active, (2) ADSC is asserted LOW, (3) ADSP is deasserted
HIGH, and (4) the Write input signals (GW, BW , and BW
)
E
[A:D]
Document #: 001-00210 Rev. *A
Page 4 of 15
PRELIMINARY
CY7C1336H
ZZ Mode Electrical Characteristics
Parameter
Description
Sleep mode standby current
Device operation to ZZ
Test Conditions
ZZ > V – 0.2V
Min.
Max.
Unit
mA
ns
I
t
t
t
t
40
DDZZ
DD
ZZ > V – 0.2V
2t
2t
ZZS
DD
CYC
CYC
ZZ recovery time
ZZ < 0.2V
2t
ns
ZZREC
ZZI
CYC
ZZ Active to sleep current
ZZ Inactive to exit sleep current
This parameter is sampled
This parameter is sampled
ns
0
ns
RZZI
Truth Table [2, 3, 4, 5, 6]
ADDRESS
Used
Cycle Description
CE CE CE
3
ZZ ADSP ADSC ADV WRITE OE CLK
DQ
1
2
Deselected Cycle,
Power-down
None
None
None
None
None
H
L
L
L
X
X
X
X
H
X
X
L
L
L
L
L
X
L
X
X
L
L
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
L-H
L-H
L-H
L-H
L-H
Tri-State
Deselected Cycle,
Power-down
L
L
Tri-State
Tri-State
Tri-State
Tri-State
Deselected Cycle,
Power-down
X
L
L
Deselected Cycle,
Power-down
H
H
Deselected Cycle,
Power-down
X
Sleep Mode, Power-down
Read Cycle, Begin Burst
Read Cycle, Begin Burst
Write Cycle, Begin Burst
Read Cycle, Begin Burst
Read Cycle, Begin Burst
Read Cycle, Continue Burst
Read Cycle, Continue Burst
Read Cycle, Continue Burst
Read Cycle, Continue Burst
Write Cycle, Continue Burst
Write Cycle, Continue Burst
Read Cycle, Suspend Burst
Read Cycle, Suspend Burst
Read Cycle, Suspend Burst
Read Cycle, Suspend Burst
Write Cycle, Suspend Burst
None
External
External
External
External
External
Next
X
L
X
H
H
H
H
H
X
X
X
X
X
X
X
X
X
X
X
X
X
L
H
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
X
L
X
X
X
L
X
X
X
X
X
X
L
X
X
X
L
X
L
X
Tri-State
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
Q
L
L
L
H
X
L
Tri-State
L
L
H
H
H
H
H
X
X
H
X
H
H
X
X
H
X
D
L
L
L
H
H
H
H
H
H
L
Q
L
L
L
H
L
Tri-State
X
X
H
H
X
H
X
X
H
H
X
H
X
X
X
X
X
X
X
X
X
X
X
X
H
H
H
H
H
H
H
H
H
H
H
H
Q
Next
L
H
L
Tri-State
Next
L
Q
Next
L
H
X
X
L
Tri-State
Next
L
D
Next
L
L
D
Current
Current
Current
Current
Current
Current
H
H
H
H
H
H
H
H
H
H
L
Q
H
L
Tri-State
Q
H
X
X
Tri-State
D
D
Write Cycle, Suspend Burst
L
Notes:
2. X = “Don't Care.” H = Logic HIGH, L = Logic LOW.
3. WRITE = L when any one or more Byte Write Enable signals (BW , BW , BW , BW ) and BWE = L or GW = L. WRITE = H when all Byte Write Enable signals
A
B
C
D
(BW , BW , BW , BW ), BWE, GW = H.
A
B
C
D
4. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
5. The SRAM always initiates a Read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BW
. Writes may occur only on subsequent clocks
[A: D]
after the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the Write cycle to allow the outputs to tri-state. OE is a
don't care for the remainder of the Write cycle.
6. OE is asynchronous and is not sampled with the clock rise. It is masked internally during Write cycles. During a Read cycle all data bits are Tri-State when OE
is inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW).
Document #: 001-00210 Rev. *A
Page 5 of 15
PRELIMINARY
CY7C1336H
Truth Table for Read/Write[2, 3]
Function
GW
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
L
BWE
H
L
BW
X
H
H
H
H
H
H
H
H
L
BW
X
H
H
H
H
L
BW
X
H
H
L
BW
A
D
C
B
Read
Read
X
H
L
Write Byte (A, DQP )
L
A
Write Byte (B, DQP )
L
H
L
B
Write Bytes (B, A, DQP , DQP )
L
L
A
B
Write Byte (C, DQP )
L
H
H
L
H
L
C
Write Bytes (C, A, DQP , DQP )
L
L
C
A
Write Bytes (C, B, DQP , DQP )
L
L
H
L
C
B
Write Bytes (C, B, A, DQP , DQP , DQP )
L
L
L
C
B
A
Write Byte (D, DQP )
L
H
H
H
H
L
H
H
L
H
L
D
Write Bytes (D, A, DQP , DQP )
L
L
D
A
Write Bytes (D, B, DQP , DQP )
L
L
H
L
D
A
Write Bytes (D, B, A, DQP , DQP , DQP )
L
L
L
D
B
A
Write Bytes (D, B, DQP , DQP )
L
L
H
H
L
H
L
D
B
Write Bytes (D, B, A, DQP , DQP , DQP )
L
L
L
D
C
A
Write Bytes (D, C, A, DQP , DQP , DQP )
L
L
L
H
L
D
B
A
Write All Bytes
Write All Bytes
L
L
L
L
X
X
X
X
X
Document #: 001-00210 Rev. *A
Page 6 of 15
PRELIMINARY
CY7C1336H
Current into Outputs (LOW)......................................... 20 mA
Maximum Ratings
Static Discharge Voltage........................................... >2001V
(per MIL-STD-883, Method 3015)
(Above which the useful life may be impaired. For user guide-
lines, not tested.)
Latch-up Current..................................................... >200 mA
Storage Temperature .................................–65°C to +150°C
Operating Range
Ambient Temperature with
Power Applied.............................................–55°C to +125°C
Ambient
]
Supply Voltage on V Relative to GND........ –0.5V to +4.6V
Range
Commercial
Industrial
Temperature
0°C to +70°C
–40°C to +85°C
V
V
DDQ
DD
DD
DC Voltage Applied to Outputs
in Tri-State........................................... –0.5V to V
3.3V
−5%/+10%
3.3V –5%
+ 0.5V
to V
DDQ
DD
DC Input Voltage....................................–0.5V to V + 0.5V
DD
[7, 8]
Electrical Characteristics Over the Operating Range
Parameter
Description
Power Supply Voltage
I/O Supply Voltage
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Test Conditions
Min.
Max.
Unit
V
V
V
V
V
V
V
I
3.135
3.135
2.4
3.6
3.6
DD
DDQ
OH
OL
IH
V
for 3.3V I/O, I = –4.0 mA
V
OH
for 3.3V I/O, I = 8.0 mA
0.4
V
OL
for 3.3V I/O
for 3.3V I/O
GND ≤ V ≤ V
2.0
–0.3
−5
V
+ 0.3V
V
DD
[7]
Input LOW Voltage
0.8
5
V
IL
Input Leakage Current
except ZZ and MODE
µA
X
I
DDQ
Input Current of MODE
Input = V
Input = V
Input = V
Input = V
–30
–5
µA
µA
SS
DD
SS
DD
5
Input Current of ZZ
µA
30
5
µA
I
I
Output Leakage Current
GND ≤ V ≤ V
, Output Disabled
–5
µA
OZ
I
DDQ
V
Operating Supply
V = Max., I
DD
= 0 mA,
7.5-ns cycle, 133 MHz
10-ns cycle, 100 MHz
225
205
90
mA
mA
mA
mA
DD
DD
OUT
Current
f = f
= 1/t
MAX CYC
I
I
I
I
Automatic CE Power-Down Max. V , Device Deselected, 7.5-ns cycle, 133 MHz
DD
Current—TTL Inputs
SB1
V
≥ V or V ≤ V , f = f
IN IH IN IL MAX,
10-ns cycle, 100 MHz
80
inputs switching
Automatic CE Power-Down Max. V , Device Deselected, All speeds
Current—CMOS Inputs
40
mA
SB2
SB3
SB4
DD
V
≥ V – 0.3V or V ≤ 0.3V,
IN DD IN
f = 0, inputs static
Automatic CE Power-Down Max. V , Device Deselected, 7.5-ns cycle, 133 MHz
Current—CMOS Inputs
75
65
mA
mA
DD
V
f = f
≥ V
– 0.3V or V ≤ 0.3V,
IN
DDQ IN
10-ns cycle, 100 MHz
, inputs switching
MAX
Automatic CE Power-Down Max. V , Device Deselected, All speeds
45
mA
DD
Current—TTL Inputs
V
≥ V – 0.3V or V ≤ 0.3V,
IN DD IN
f = 0, inputs static
Notes:
7. Overshoot: V (AC) < V +1.5V (Pulse width less than t
/2), undershoot: V (AC) > –2V (Pulse width less than t /2).
CYC
IH
DD
CYC
IL
8. T
: Assumes a linear ramp from 0v to V (min.) within 200 ms. During this time V < V and V
< V
.
Power-up
DD
IH
DD
DDQ
DD
Document #: 001-00210 Rev. *A
Page 7 of 15
PRELIMINARY
CY7C1336H
Capacitance[9]
100 TQFP
Max.
Parameter
Description
Input Capacitance
Test Conditions
T = 25°C, f = 1 MHz,
Unit
pF
C
5
5
5
IN
A
V
= 3.3V, V
= 3.3V
DD
DDQ
C
C
Clock Input Capacitance
Input/Output Capacitance
pF
CLK
I/O
pF
Thermal Resistance[9]
100 TQFP
Package
Parameter
Description
Test Conditions
Unit
Θ
Θ
Thermal Resistance
(Junction to Ambient)
Test conditions follow standard test
methods and procedures for
measuring thermal impedance, per
EIA/JESD51
30.32
°C/W
JA
Thermal Resistance
(Junction to Case)
6.85
°C/W
JC
AC Test Loads and Waveforms
3.3V I/O Test Load
R = 317Ω
3.3V
OUTPUT
ALL INPUT PULSES
90%
VDDQ
OUTPUT
90%
10%
Z = 50Ω
0
R = 50Ω
10%
L
GND
5 pF
R = 351Ω
≤ 1 ns
≤ 1 ns
INCLUDING
JIG AND
SCOPE
V = 1.5V
L
(c)
(a)
(b)
Note:
9. Tested initially and after any design or process change that may affect these parameters.
Document #: 001-00210 Rev. *A
Page 8 of 15
PRELIMINARY
CY7C1336H
[10, 11]
Switching Characteristics Over the Operating Range
133 MHz
100 MHz
Parameter
Description
Min.
Max.
Min.
Max.
Unit
[12]
t
V
(Typical) to the First Access
1
1
ms
POWER
DD
Clock
t
t
t
Clock Cycle Time
Clock HIGH
7.5
2.5
2.5
10
4.0
4.0
ns
ns
ns
CYC
CH
Clock LOW
CL
Output Times
t
t
t
t
t
t
t
Data Output Valid after CLK Rise
Data Output Hold after CLK Rise
6.5
8.0
ns
ns
ns
ns
ns
ns
ns
CDV
DOH
CLZ
2.0
0
2.0
0
[13, 14, 15]
Clock to Low-Z
[13, 14, 15]
Clock to High-Z
3.5
3.5
3.5
3.5
CHZ
OEV
OELZ
OEHZ
OE LOW to Output Valid
[13, 14, 15]
OE LOW to Output Low-Z
0
0
[13, 14, 15]
OE HIGH to Output High-Z
3.5
3.5
Set-up Times
t
t
t
t
t
t
Address Set-up before CLK Rise
1.5
1.5
1.5
1.5
1.5
1.5
2.0
2.0
2.0
2.0
2.0
2.0
ns
ns
ns
ns
ns
ns
AS
ADSP, ADSC Set-up before CLK Rise
ADV Set-up before CLK Rise
ADS
ADVS
WES
DS
GW, BWE, BW
Set-up before CLK Rise
[A:D]
Data Input Set-up before CLK Rise
Chip Enable Set-up
CES
Hold Times
t
t
t
t
t
t
Address Hold after CLK Rise
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
ns
ns
ns
ns
AH
ADSP, ADSC Hold after CLK Rise
ADH
WEH
ADVH
DH
GW, BWE, BW
Hold after CLK Rise
[A:D]
ADV Hold after CLK Rise
Data Input Hold after CLK Rise
Chip Enable Hold after CLK Rise
CEH
Notes:
10. Timing reference level is 1.5V when V
= 3.3V.
DDQ
11. Test conditions shown in (a) of AC Test Loads unless otherwise noted.
12. This part has a voltage regulator internally; t
is the time that the power needs to be supplied above V (minimum) initially before a Read or Write operation
POWER
DD
can be initiated.
13. t
, t
,t
, and t
are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage.
CHZ CLZ OELZ
OEHZ
14. At any given voltage and temperature, t
is less than t
and t
is less than t
to eliminate bus contention between SRAMs when sharing the same
CLZ
OEHZ
OELZ
CHZ
data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed
to achieve High-Z prior to Low-Z under the same system conditions.
15. This parameter is sampled and not 100% tested.
Document #: 001-00210 Rev. *A
Page 9 of 15
PRELIMINARY
CY7C1336H
Timing Diagrams
[16]
Read Cycle Timing
t
CYC
t
CLK
t
CL
CH
t
t
ADH
ADS
ADSP
ADSC
t
t
ADH
ADS
t
t
AH
AS
A1
A2
ADDRESS
t
t
WES
WEH
GW, BWE,BW[A:D]
Deselect Cycle
t
t
CES
CEH
CE
t
t
ADVH
ADVS
ADV
OE
ADV suspends burst.
t
t
t
CDV
OEV
OELZ
t
t
OEHZ
CHZ
t
DOH
t
CLZ
Q(A2)
Q(A2 + 1)
Q(A2 + 2)
Q(A2 + 3)
Q(A2)
Q(A2 + 1)
Q(A2 + 2)
Q(A1)
Data Out (Q)
High-Z
t
CDV
Burst wraps around
to its initial state
Single READ
BURST
READ
DON’T CARE
UNDEFINED
Note:
16. On this diagram, when CE is LOW, CE is LOW, CE is HIGH and CE is LOW. When CE is HIGH, CE is HIGH or CE is LOW or CE is HIGH.
1
2
3
1
2
3
Document #: 001-00210 Rev. *A
Page 10 of 15
PRELIMINARY
CY7C1336H
Timing Diagrams (continued)
[16, 17]
Write Cycle Timing
t
CYC
CLK
t
t
CL
CH
t
t
ADH
ADS
ADSP
ADSC extends burst.
t
t
t
ADH
ADS
t
ADH
ADS
ADSC
t
t
AH
AS
A1
A2
A3
ADDRESS
Byte write signals are ignored for first cycle when
ADSP initiates burst.
t
t
WEH
WES
BWE,
BW[A:D]
t
t
WEH
WES
GW
t
t
CEH
CES
CE
t
t
ADVH
ADVS
ADV
ADV suspends burst.
OE
t
t
DH
DS
Data in (D)
D(A2)
D(A2 + 1)
D(A2 + 1)
D(A2 + 2)
D(A2 + 3)
D(A3)
D(A3 + 1)
D(A3 + 2)
D(A1)
High-Z
t
OEHZ
Data Out (Q)
BURST READ
Single WRITE
BURST WRITE
Extended BURST WRITE
DON’T CARE
UNDEFINED
Note:
17.
Full width Write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BW
LOW.
[A:D]
Document #: 001-00210 Rev. *A
Page 11 of 15
PRELIMINARY
CY7C1336H
Timing Diagrams (continued)
[16, 18, 19]
Read/Write Timing
t
CYC
CLK
t
t
CL
CH
t
t
ADH
ADS
ADSP
ADSC
t
t
AH
AS
A1
A2
A3
A4
A5
A6
ADDRESS
BWE, BW[A:D]
CE
t
t
WEH
WES
t
t
CEH
CES
ADV
OE
t
t
DH
DS
t
OELZ
t
High-Z
D(A3)
D(A5)
D(A6)
Data In (D)
t
OEHZ
CDV
Data Out (Q)
Q(A1)
Q(A2)
Q(A4)
Q(A4+1)
Q(A4+2)
Q(A4+3)
Back-to-Back
Back-to-Back READs
Single WRITE
BURST READ
WRITEs
DON’T CARE
UNDEFINED
Notes:
18. The data bus (Q) remains in High-Z following a Write cycle unless an ADSP, ADSC, or ADV cycle is performed.
19. GW is HIGH.
Document #: 001-00210 Rev. *A
Page 12 of 15
PRELIMINARY
CY7C1336H
Timing Diagrams (continued)
[20, 21]
ZZ Mode Timing
CLK
t
t
ZZ
ZZREC
ZZ
t
ZZI
I
SUPPLY
I
DDZZ
t
RZZI
ALL INPUTS
(except ZZ)
DESELECT or READ Only
Outputs (Q)
High-Z
DON’T CARE
Notes:
20. Device must be deselected when entering ZZ mode. See Cycle Descriptions table for all possible signal conditions to deselect the device.
21. DQs are in High-Z when exiting ZZ sleep mode.
Document #: 001-00210 Rev. *A
Page 13 of 15
PRELIMINARY
CY7C1336H
Ordering Information
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Package Type
133
CY7C1336H-133AXC 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
CY7C1336H-133AXI 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
CY7C1336H-100AXC 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
CY7C1336H-100AXI 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
Commercial
Industrial
100
Commercial
Industrial
Please contact your local Cypress sales representative for availability of these parts.
Package Diagram
100-pin TQFP (14 x 20 x 1.4 mm) (51-85050)
16.00 0.20
14.00 0.10
1.40 0.05
100
81
80
1
0.30 0.08
0.65
TYP.
12° 1°
(8X)
SEE DETAIL
A
30
51
31
50
0.20 MAX.
1.60 MAX.
R 0.08 MIN.
0.20 MAX.
0° MIN.
SEATING PLANE
STAND-OFF
0.05 MIN.
0.15 MAX.
NOTE:
1. JEDEC STD REF MS-026
0.25
GAUGE PLANE
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE
R 0.08 MIN.
0.20 MAX.
BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH
3. DIMENSIONS IN MILLIMETERS
0°-7°
0.60 0.15
1.00 REF.
0.20 MIN.
51-85050-*B
DETAIL
A
Pentium is a registered trademark, and i486 is a trademark, of Intel Corporation. All product and company names mentioned in
this document may be the trademarks of their respective holders.
Document #: 001-00210 Rev. *A
Page 14 of 15
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
PRELIMINARY
CY7C1336H
Document History Page
Document Title: CY7C1336H 2-Mbit (64K x 32) Flow-Through Sync SRAM
Document Number: 001-00210
Orig. of
REV.
**
ECN NO. Issue Date Change
Description of Change
347377
428408
See ECN
See ECN
PCI
New Data Sheet
*A
NXR
Changed address of Cypress Semiconductor Corporation on Page# 1 from
“3901 North First Street” to “198 Champion Court”
Changed Three-State to Tri-State.
Modified “Input Load” to “Input Leakage Current except ZZ and MODE” in the
Electrical Characteristics Table.
Modified test condition from V < V to V < V
IH
DD
IH
DD
Replaced Package Name column with Package Diagram in the Ordering
Information table.
Replaced Package Diagram of 51-85050 from *A to *B
Document #: 001-00210 Rev. *A
Page 15 of 15
|