CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
18-Mbit QDR™-II+ SRAM 4-Word Burst
Architecture (2.0 Cycle Read Latency)
Features
Functional Description
■ Separate Independent read and write data ports
❐ Supports concurrent transactions
■ 300 MHz to 375 MHz clock for high bandwidth
The CY7C1141V18, CY7C1156V18, CY7C1143V18, and
CY7C1145V18 are 1.8V Synchronous Pipelined SRAMs,
equipped with QDR™-II+ architecture. QDR-II+ architecture
consists of two separate ports to access the memory array. The
read port has dedicated data outputs to support read operations
and the write port has dedicated data inputs to support write
operations. QDR-II+ architecture has separate data inputs and
data outputs to completely eliminate the need to “turn-around”
the data bus required with common IO devices. Access to each
■ 4-Word Burst for reducing address bus frequency
■ DoubleDataRate(DDR)interfacesonbothreadandwriteports
(data transferred at 750 MHz) at 375 MHz
■ Read latency of 2.0 clock cycles
■ Two input clocks (K and K) for precise DDR timing
❐ SRAM uses rising edges only
■ Echo clocks (CQ and CQ) simplify data capture in high speed
port is accomplished through
a
common address bus.
Addresses for read and write addresses are latched on alternate
rising edges of the input (K) clock. Accesses to the QDR-II+ read
and write ports are completely independent of one another. To
maximize data throughput, both read and write ports are
equipped with Double Data Rate (DDR) interfaces. Each
address location is associated with four 8-bit words
(CY7C1141V18), or 9-bit words (CY7C1156V18), or 18-bit words
(CY7C1143V18), or 36-bit words (CY7C1145V18) that burst
sequentially into or out of the device. Because data can be trans-
ferred into and out of the device on every rising edge of both input
clocks K and K, memory bandwidth is maximized while simpli-
fying system design by eliminating bus “turn-arounds”.
systems
■ Single multiplexed address input bus latches address inputs
for both read and write ports
■ Separate Port Selects for depth expansion
■ Data valid pin (QVLD) to indicate valid data on the output
■ Synchronous internally self-timed writes
■ Available in x8, x9, x18, and x36 configurations
■ Full data coherency providing most current data
[1]
■ Core VDD = 1.8V ± 0.1V; IO VDDQ = 1.4V to VDD
Depth expansion is accomplished with Port Selects for each port.
Port Selects enable each port to operate independently.
■ Available in 165-Ball FBGA package (13 x 15 x 1.4 mm)
■ Offered in both Pb-free and non Pb-free packages
■ Variable drive HSTL output buffers
All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the K or K input clocks. Writes are
conducted with on-chip synchronous self-timed write circuitry.
■ JTAG 1149.1 compatible test access port
■ Delay Lock Loop (DLL) for accurate data placement
Configurations
With Read Cycle Latency of 2.0 cycles:
CY7C1141V18 – 2M x 8
CY7C1156V18 – 2M x 9
CY7C1143V18 – 1M x 18
CY7C1145V18 – 512K x 36
Selection Guide
Description
Maximum Operating Frequency
Maximum Operating Current
375 MHz
375
333 MHz
333
300 MHz
300
Unit
MHz
mA
1020
920
850
Note
1. The QDR consortium specification for VDDQ is 1.5V + 0.1V. The Cypress QDR devices exceed the QDR consortium specification and are capable of supporting VDDQ
= 1.4V to VDD
.
Cypress Semiconductor Corporation
Document Number: 001-06583 Rev. *D
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 06, 2008
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Logic Block Diagram (CY7C1143V18)
D[17:0]
18
Write Write Write Write
Address
Register
A(17:0)
Reg
Reg Reg
Reg
18
Address
Register
A(17:0)
18
RPS
K
K
Control
Logic
CLK
Gen.
DOFF
Read Data Reg.
72
CQ
CQ
36
VREF
Reg.
Reg.
Reg.
WPS
Control
Logic
Q[17:0]
36
BWS[1:0]
18
18
QVLD
Logic Block Diagram (CY7C1145V18)
D[35:0]
36
Write Write Write Write
Address
Register
A(16:0)
Reg
Reg Reg
Reg
17
Address
Register
A(16:0)
17
RPS
K
K
Control
Logic
CLK
Gen.
DOFF
Read Data Reg.
144
CQ
CQ
72
VREF
Reg.
Reg.
Reg.
WPS
Control
Logic
Q[35:0]
72
BWS[3:0]
36
36
QVLD
Document Number: 001-06583 Rev. *D
Page 3 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Pin Configurations
165-Ball FBGA (13 x 15 x 1.4 mm) Pinout
CY7C1141V18 (2M x 8)
1
2
3
A
6
K
9
A
10
NC/36M
11
CQ
5
NWS
7
8
RPS
A
4
WPS
NC/72M
NC/144M
A
CQ
1
NC
NC
NC
NC
NC
D4
NC
NC
NC
A
NC/288M
A
K
NWS
NC
NC
NC
NC
NC
NC
Q3
D3
NC
B
C
D
0
V
NC
A
V
SS
SS
V
V
V
V
V
SS
SS
SS
SS
SS
NC
NC
NC
NC
NC
D5
Q4
NC
Q5
V
V
V
V
V
NC
NC
NC
D2
NC
NC
Q2
NC
NC
ZQ
D1
NC
Q0
E
F
DDQ
SS
SS
SS
DDQ
V
V
V
V
V
DDQ
DD
SS
DD
DDQ
V
V
V
V
V
G
DDQ
DD
SS
DD
DDQ
V
V
V
V
V
V
V
V
V
H
J
REF
DDQ
DDQ
DD
SS
DD
DDQ
DDQ
REF
DOFF
NC
NC
NC
Q6
NC
D7
NC
V
V
V
V
V
NC
Q1
NC
NC
NC
NC
NC
DDQ
DD
SS
DD
DDQ
NC
NC
NC
NC
NC
NC
D6
NC
NC
Q7
V
V
V
V
V
NC
NC
NC
NC
NC
K
L
DDQ
DD
SS
DD
DDQ
V
V
V
V
V
DDQ
SS
SS
SS
DDQ
V
V
V
V
V
D0
NC
NC
M
N
P
SS
SS
SS
SS
SS
V
A
A
A
A
A
V
SS
SS
NC
QVLD
A
A
A
A
A
A
TDO
TCK
A
NC
A
TMS
TDI
R
CY7C1156V18 (2M x 9)
1
2
NC/72M
NC
3
6
K
9
10
NC/36M
NC
11
CQ
Q4
D4
NC
Q3
5
NC
7
8
4
WPS
A
CQ
NC
NC
NC
NC
A
NC/144M RPS
A
A
B
C
D
NC
NC
NC
Q5
NC
Q6
NC/288M
A
K
BWS
A
A
NC
NC
NC
NC
NC
NC
0
NC
V
NC
V
NC
SS
SS
SS
D5
V
V
V
V
V
NC
SS
SS
SS
SS
NC
V
V
V
V
V
V
V
V
V
V
V
D3
E
F
DDQ
SS
SS
SS
DDQ
NC
NC
NC
V
V
V
V
NC
NC
NC
ZQ
D2
NC
Q1
DDQ
DD
SS
DD
DDQ
DDQ
DDQ
DDQ
D6
V
V
V
V
NC
G
H
J
DDQ
DD
SS
DD
V
V
V
V
DOFF
NC
V
V
V
V
DDQ
DD
DDQ
REF
REF
DDQ
SS
DD
NC
NC
Q7
NC
D8
NC
V
V
V
V
NC
Q2
NC
NC
NC
NC
D0
DDQ
DD
SS
DD
NC
NC
D7
NC
NC
Q8
V
V
V
V
NC
NC
NC
NC
NC
K
L
DDQ
DD
SS
DD
DDQ
DDQ
NC
V
V
V
V
DDQ
SS
SS
SS
NC
NC
NC
V
V
V
V
V
D1
NC
Q0
M
N
P
SS
SS
SS
SS
SS
SS
V
A
A
A
A
A
A
V
SS
NC
QVLD
A
A
A
A
A
TDO
TCK
A
NC
A
TMS
TDI
R
Document Number: 001-06583 Rev. *D
Page 4 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Pin Configurations (continued)
165-Ball FBGA (13 x 15 x 1.4 mm) Pinout
CY7C1143V18 (1M x 18)
2
3
5
BWS
NC
A
6
K
7
9
10
NC/72M
NC
11
CQ
Q8
D8
D7
Q6
Q5
D5
1
4
WPS
A
8
CQ
NC
NC
NC
NC
NC
NC
NC/144M NC/36M
NC/288M RPS
A
A
B
C
D
E
F
1
Q9
NC
D9
K
BWS
A
A
NC
NC
NC
NC
NC
NC
0
D10
Q10
Q11
D12
Q13
V
NC
V
Q7
SS
SS
SS
D11
NC
V
V
V
V
V
NC
SS
SS
SS
SS
V
V
V
V
V
V
V
D6
DDQ
SS
SS
SS
DDQ
DDQ
DDQ
Q12
D13
V
V
V
V
NC
DDQ
DD
SS
DD
V
V
V
V
NC
G
DDQ
DD
SS
DD
V
DOFF
NC
V
NC
V
D14
V
V
V
V
V
V
V
V
V
ZQ
D4
H
J
DDQ
REF
DDQ
DDQ
DD
SS
DD
DDQ
DDQ
REF
V
V
NC
Q4
D3
NC
Q1
NC
D0
DDQ
DD
SS
DD
NC
NC
NC
NC
NC
NC
Q15
NC
Q14
D15
D16
Q16
Q17
V
V
V
V
V
V
NC
NC
NC
NC
NC
Q3
Q2
K
L
DDQ
DD
SS
DD
DDQ
DDQ
V
V
V
V
DDQ
SS
SS
SS
V
V
V
V
V
D2
D1
Q0
M
N
P
SS
SS
SS
SS
SS
SS
D17
NC
V
A
A
A
A
A
V
SS
QVLD
A
A
A
A
A
A
R
TDO
A
A
TMS
TDI
TCK
NC
CY7C1145V18 (512K x 36)
7
1
2
3
8
9
10
11
CQ
Q8
D8
D7
4
WPS
A
5
BWS
BWS
A
6
K
NC/288M NC/72M
NC/36M NC/144M
A
B
C
D
CQ
BWS
RPS
A
2
3
1
0
Q27
D27
D28
Q29
Q30
D30
Q18
Q28
D20
D29
Q21
D22
D18
D19
Q19
Q20
D21
Q22
K
D17
D16
Q16
Q15
D14
Q13
Q17
Q7
BWS
A
V
NC
V
SS
SS
V
V
V
V
V
D15
D6
SS
SS
SS
SS
SS
V
V
V
V
V
Q6
Q5
D5
ZQ
D4
Q3
Q2
E
F
DDQ
SS
SS
SS
DDQ
V
V
V
V
V
Q14
D13
DDQ
DD
SS
DD
DD
DD
DD
DDQ
V
V
V
V
V
V
V
V
G
H
J
DDQ
DD
SS
DDQ
V
V
V
V
V
V
V
V
REF
REF
DDQ
DDQ
DD
SS
DDQ
DDQ
DOFF
D31
Q31
D23
V
V
V
V
D12
Q4
DDQ
DD
SS
DDQ
Q32
Q33
D33
D34
Q35
D32
Q24
Q34
D26
D35
Q23
D24
D25
Q25
Q26
V
V
V
V
Q12
D11
D10
Q10
Q9
D3
Q11
Q1
D9
K
L
DDQ
DD
SS
DD
DDQ
V
V
V
V
V
V
DDQ
SS
SS
SS
DDQ
V
V
V
V
D2
D1
Q0
M
N
P
SS
SS
SS
SS
SS
V
A
A
A
A
A
A
V
SS
SS
QVLD
D0
A
A
A
A
A
TDO
TCK
A
A
TMS
TDI
R
NC
Document Number: 001-06583 Rev. *D
Page 5 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Pin Definitions
Pin Name
IO
Pin Description
Data Input Signals. Sampled on the rising edge of K and K clocks during valid write operations.
D[x:0]
Input-
Synchronous CY7C1141V18−D[7:0]
CY7C1156V18−D[8:0]
CY7C1143V18−D[17:0]
CY7C1145V18−D[35:0]
WPS
Input-
Write Port Select − Active LOW. Sampled on the rising edge of the K clock. When asserted active,
Synchronous a write operation is initiated. Deasserting deselects the write port. Deselecting the write port causes
D[x:0] to be ignored.
,
Input-
Nibble Write Select 0, 1 − Active LOW.(CY7C1141V18 Only) Sampled on the rising edge of the K
NWS0, NWS1
Synchronous and K clocks during write operations. This is used to select the nibble that is written into the device
NWS0 controls D[3:0] and NWS1 controls D[7:4]
.
All the Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble Write
Select causes the corresponding nibble of data to be ignored and not written into the device.
BWS0, BWS1,
BWS2, BWS3
Input-
Byte Write Select 0, 1, 2, and 3 − Active LOW. Sampled on the rising edge of the K and K clocks
Synchronous during write operations. This is used to select the byte that is written into the device during the current
portion of the write operations. Bytes not written remain unaltered.
CY7C1156V18 − BWS0 controls D[8:0]
CY7C1143V18 BWS controls D[8:0] and BWS1 controls D[17:9]
.
−
CY7C1145V18 BWS0 controls D[8:0], BWS1 controls D[17:9], BWS2 controls D[26:18], and BWS3
−
0
controls D[35:27]
.
All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write Select
causes the corresponding byte of data to be ignored and not written into the device.
A
Input-
Address Inputs. Sampled on the rising edge of the K clock during active read and write operations.
Synchronous These address inputs are multiplexed for both read and write operations. Internally, the device is
organized as 2M x 8 (4 arrays each of 512K x 8) for CY7C1141V18, 2M x 9 (4 arrays each of 512K
x 9) for CY7C1156V18, 1M x 18 (4 arrays each of 256K x 18) for CY7C1143V18, and 512K x 36 (4
arrays each of 128K x 36) for CY7C1145V18. Therefore, only 19 address inputs are needed to access
the entire memory array of CY7C1141V18 and CY7C1156V18, 18 address inputs for CY7C1143V18
and 17 address inputs for CY7C1145V18. These inputs are ignored when the appropriate port is
deselected.
Q[x:0]
Outputs-
Data Output signals. These pins drive out the requested data during a read operation. Valid data is
Synchronous driven out on the rising edge of both the K and K clocks during read operations or K and K when in
single clock mode. When the read port is deselected, Q[x:0] are automatically tri-stated.
CY7C1141V18−Q[7:0]
CY7C1156V18−Q[8:0]
CY7C1143V18−Q[17:0]
CY7C1145V18−Q[35:0]
RPS
Input-
Read Port Select − Active LOW. Sampled on the rising edge of Positive Input Clock (K). When
Synchronous active, a read operation is initiated. Deasserting causes the read port to be deselected. When
deselected, the pending access is enabled to complete and the output drivers are automatically
tri-stated following the next rising edge of the K clock. Each read access consists of a burst of four
sequential transfers.
QVLD
K
Valid output Valid Output Indicator. The Q Valid indicates valid output data. QVLD is edge aligned with CQ and
indicator
CQ.
Input-
Clock
Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the device
and to drive out data through Q[x:0] when in single clock mode. All accesses are initiated on the rising
edge of K.
K
Input-
Clock
Negative Input Clock Input. K is used to capture synchronous inputs presented to the device and
to drive out data through Q[x:0] when in single clock mode.
CQ
Echo Clock Synchronous Echo Clock Outputs. This is a free running clock and is synchronized to the input
clock (K) of the QDR-II+. The timings for the echo clocks are shown in the “Switching Characteristics”
on page 23.
Document Number: 001-06583 Rev. *D
Page 6 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Pin Definitions (continued)
Pin Name
CQ
IO
Pin Description
Echo Clock Synchronous Echo Clock Outputs. This is a free running clock and is synchronized to the input
clock (K) of the QDR-II+. The timings for the echo clocks are shown in the “Switching Characteristics”
on page 23.
ZQ
Input
Output Impedance Matching Input. This input is used to tune the device outputs to the system data
bus impedance. CQ, CQ and Q[x:0] output impedance are set to 0.2 x RQ, where RQ is a resistor
connected between ZQ and ground. Alternatively, connect this pin directly to VDDQ, which enables
the minimum impedance mode. This pin cannot be connected directly to GND or left unconnected.
DOFF
Input
DLL Turn Off − Active LOW. Connecting this pin to ground turns off the DLL inside the device. The
timings in the DLL turned off operationis different from those listed in this data sheet. For normal
operation, connect this pin to a pull up through a 10 KΩ or less pull up resistor. The device behaves
in QDR-I mode when the DLL is turned off. In this mode, operate the device at a frequency of up to
167 MHz with QDR-I timing.
TDO
Output
Input
Input
Input
N/A
TDO for JTAG.
TCK
TCK Pin for JTAG.
TDI
TDI Pin for JTAG.
TMS
TMS Pin for JTAG.
NC
Not Connected to the Die. Tie to any voltage level.
Not Connected to the Die. Tie to any voltage level.
Not Connected to the Die. Tie to any voltage level.
Not Connected to the Die. Tie to any voltage level.
Not Connected to the Die. Tie to any voltage level.
Reference Voltage Input. Static input used to set the reference level for HSTL inputs, outputs, and
NC/36M
NC/72M
NC/144M
NC/288M
VREF
N/A
N/A
N/A
N/A
Input-
Reference AC measurement points.
VDD
VSS
Power Supply Power Supply Inputs to the Core of the Device.
Ground
Ground for the Device.
VDDQ
Power Supply Power Supply Inputs for the Outputs of the Device.
Document Number: 001-06583 Rev. *D
Page 7 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Write Operations
Functional Overview
Write operations are initiated by asserting WPS active at the
rising edge of the Positive Input Clock (K). On the following K
clock rise the data presented to D[17:0] is latched and stored into
the lower 18-bit Write Data register, provided BWS[1:0] are both
asserted active. On the subsequent rising edge of the Negative
Input Clock (K) the information presented to D[17:0] is also stored
into the Write Data register, provided BWS[1:0] are both asserted
active. This process continues for one more cycle until four 18-bit
words (a total of 72 bits) of data are stored in the SRAM. The 72
bits of data are then written into the memory array at the specified
location. Therefore, write accesses to the device cannot be
initiated on two consecutive K clock rises. The internal logic of
the device ignores the second write request. Initiate write
accesses on every other rising edge of the Positive Input Clock
(K). This pipelines the data flow such that 18 bits of data can be
transferred into the device on every rising edge of the input
clocks (K and K).
The CY7C1141V18, CY7C1156V18, CY7C1143V18, and
CY7C1145V18 are synchronous pipelined Burst SRAMs
equipped with both a read port and a write port. The read port is
dedicated to read operations and the write port is dedicated to
write operations. Data flows into the SRAM through the write port
and out through the read port. These devices multiplex the
address inputs in order to minimize the number of address pins
required. By having separate read and write ports, the QDR-II+
completely eliminates the need to “turn-around” the data bus and
avoids any possible data contention, thereby simplifying system
design. Each access consists of four 8-bit data transfers in the
case of CY7C1141V18, four 9-bit data transfers in the case of
CY7C1156V18, four 18-bit data transfers in the case of
CY7C1143V18, and four 36-bit data transfers in the case of
CY7C1145V18 in two clock cycles.
Accesses for both ports are initiated on the Positive Input Clock
(K). All synchronous input and output timing refer to the rising
edge of the Input clocks (K/K).
When deselected, the write port ignores all inputs after the
pending write operations are completed.
All synchronous data inputs (D[x:0]) pass through input registers
controlled by the input clocks (K and K). All synchronous data
outputs (Q[x:0]) pass through output registers controlled by the
rising edge of the Input clocks (K and K) as well.
Byte Write Operations
Byte Write operations are supported by the CY7C1143V18. A
write operation is initiated as described in the Write Operations.
The bytes that are written are determined by BWS0 and BWS1,
which are sampled with each set of 18-bit data words. Asserting
the appropriate Byte Write Select input during the data portion of
a write enables the data being presented to be latched and
written into the device. Deasserting the Byte Write Select input
during the data portion of a write enables the data stored in the
device for that byte to remain unaltered. Use this feature to
simplify read/modify/write operations to a Byte Write operation.
All synchronous control (RPS, WPS, BWS[x:0]) inputs pass
through input registers controlled by the rising edge of the input
clocks (K/K). CY7C1143V18 is described in the following
sections. The same basic descriptions apply to CY7C1141V18,
CY7C1156V18, and CY7C1145V18.
Read Operations
The CY7C1143V18 is organized internally as four arrays of 256K
x 18. Accesses are completed in a burst of four sequential 18-bit
data words. Read operations are initiated by asserting RPS
active at the rising edge of the Positive Input Clock (K). The
address presented to Address inputs are stored in the read
address register. Following the next two K clock rise, the corre-
sponding lowest order 18-bit word of data is driven onto the
Q[17:0] using K as the output timing reference. On the subse-
quent rising edge of K the next 18-bit data word is driven onto
the Q[17:0]. This process continues until all four 18-bit data words
are driven out onto Q[17:0]. The requested data is valid 0.45 ns
from the rising edge of the Input clock K or K. To maintain the
internallogic, each read access must be allowed to complete.
Each read access consists of four 18-bit data words and takes
two clock cycles to complete. Therefore, read accesses to the
device cannot be initiated on two consecutive K clock rises. The
internal logic of the device ignores the second read request.
Initiate read accesses on every other K clock rise. This pipelines
the data flow such that data is transferred out of the device on
every rising edge of the input clocks K and K.
Concurrent Transactions
The read and write ports on the CY7C1143V18 operate indepen-
dently of one another. Because each port latches the address
inputs on different clock edges, the user can read or write to any
location, regardless of the transaction on the other port. If the
ports access the same location when a read follows a write in
successive clock cycles, the SRAM delivers the most recent
information associated with the specified address location. This
includes forwarding data from a write cycle that was initiated on
the previous K clock rise.
Read accesses and write access must be scheduled such that
one transaction is initiated on any clock cycle. If both ports are
selected on the same K clock rise, the arbitration depends on the
previous state of the SRAM. If both ports were deselected, the
read port takes priority. If a read was initiated on the previous
cycle, the write port is based on priority (since read operations
cannot be initiated on consecutive cycles). If a write was initiated
on the previous cycle, the read port is based on priority (since
write operations cannot be initiated on consecutive cycles).
Therefore, asserting both port selects active from a deselected
state results in alternating read/write operations initiated, with the
first access being a read.
When the read port is deselected, the CY7C1143V18 first
completes the pending read transactions. Synchronous internal
circuitry automatically tri-states the outputs following the next
rising edge of the Positive Input Clock (K). This enables for a
seamless transition between devices without the insertion of wait
states in a depth expanded memory.
Document Number: 001-06583 Rev. *D
Page 8 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
synchronized to the input clock of the QDR-II+. The timings for
the echo clocks are shown in the AC timing table.
Depth Expansion
The CY7C1143V18 has a Port Select input for each port. This
enables easy depth expansion. Both Port Selects are sampled
on the rising edge of the Positive Input Clock only (K). Each port
select input can deselect the specified port. Deselecting a port
does not affect the other port. All pending transactions (read and
write) are completed before the device is deselected.
Valid Data Indicator (QVLD)
QVLD is provided on the QDR-II+ to simplify data capture on high
speed systems. The QVLD is generated by the QDR-II+ device
along with data output. This signal is also edge-aligned with the
echo clock and follows the timing of any data pin. This signal is
asserted half a cycle before valid data arrives.
Programmable Impedance
An external resistor, RQ, must be connected between the ZQ pin
on the SRAM and VSS to enable the SRAM to adjust its output
driver impedance. The value of RQ must be 5X the value of the
intended line impedance driven by the SRAM. The allowable
range of RQ to guarantee impedance matching with a tolerance
of ±15% is between 175Ω and 350Ω, with VDDQ = 1.5V. The
output impedance is adjusted every 1024 cycles upon power up
to account for drifts in supply voltage and temperature.
DLL
These chips use a Delay Lock Loop (DLL) that is designed to
function between 120 MHz and the specified maximum clock
frequency. The DLL may be disabled by applying ground to the
DOFF pin. When the DLL is turned off, the device behaves in
QDR-I mode (with 1.0 cycle latency and a longer access time).
For more information, refer to the application note, “DLL Consid-
erations in QDRII/DDRII/QDRII+/DDRII+”. The DLL can also be
reset by slowing or stopping the input clocks K and K for a
minimum of 30 ns. However, it is not necessary for the DLL to be
reset to lock to the desired frequency. During power up, when the
DOFF is tied HIGH, the DLL gets locked after 2048 cycles of
stable clock.
Echo Clocks
Echo clocks are provided on the QDR-II+ to simplify data capture
on high speed systems. Two echo clocks are generated by the
QDR-II+. CQ is referenced with respect to K and CQ is refer-
enced with respect to K. These are free running clocks and are
Document Number: 001-06583 Rev. *D
Page 9 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Figure 1 shows the four QDR-II+ used in an application.
Figure 1. Appliation Example
RQ = 250ohms
RQ = 250ohms
ZQ
CQ/CQ
Q
ZQ
CQ/CQ
Q
Vt
SRAM #1
BWS
SRAM #4
D
A
D
A
R
K
RPS WPS
K
K
K
BWS
RPS WPS
DATA IN
DATA OUT
Address
R
R
Vt
Vt
RPS
BUS MASTER
WPS
BWS
(CPU or ASIC)
CLKIN/CLKIN
Source K
Source K
R = 50ohms, Vt = V
/2
DDQ
Truth Table
The truth table for the CY7C1141V18, CY7C1156V18, CY7C1143V18, and CY7C1145V18 follows.[2, 3, 4, 5, 6, 7]
Operation
Write Cycle:
K
DQ
DQ
DQ
DQ
L-H
H[8] L[9] D(A) at K(t + 1) ↑ D(A + 1) at K(t + 1) ↑ D(A + 2) at K(t + 2) ↑ D(A + 3) at K(t + 2) ↑
Load address on the rising
edge of K; input write data
on two consecutive K and
K rising edges
Read Cycle:
L-H
L[9]
X
Q(A) at K(t + 2) ↑ Q(A + 1) at K(t + 2) ↑ Q(A + 2) at K(t + 3)↑ Q(A + 3) at K(t + 3) ↑
(2.0 cycle Latency)
Load address on the rising
edge of K; wait one and a
half cycle; read data on
two consecutive K and K
rising edges
NOP: No Operation
L-H
H
X
H
X
D = X
Q = High-Z
D = X
Q = High-Z
D = X
Q = High-Z
D = X
Q = High-Z
Standby: Clock Stopped Stopped
Previous State
Previous State
Previous State
Previous State
Notes
2. X = “Don't Care,” H = Logic HIGH, L = Logic LOW, ↑ represents rising edge.
3. Device powers up deselected and the outputs in a tri-state condition.
4. “A” represents address location latched by the devices when transaction was initiated. A + 1, A + 2, and A + 3 represents the address sequence in the burst.
5. “t” represents the cycle at which a Read/Write operation is started. t + 1, t + 2, and t + 3 are the first, second, and third clock cycles respectively succeeding the “t” clock
cycle.
6. Data inputs are registered at K and K rising edges. Data outputs are delivered on K and K rising edges.
7. IDo K = K = HIGH when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line charging symmetrically.
8. If this signal was LOW to initiate the previous cycle, this signal becomes a “Don’t Care” for this operation.
9. This signal was HIGH on previous K clock rise. Initiating consecutive read or write operations on consecutive K clock rises is not permitted. The device ignores the
second read orwrite request.
Document Number: 001-06583 Rev. *D
Page 10 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Write Cycle Descriptions
The write cycle descriptions of CY7C1141V18 and CY7C1143V18 follows. [2, 10]
BWS0/ BWS1/
K
Comments
K
NWS0 NWS1
L
L
L–H
–
During the data portion of a write sequence:
CY7C1141V18 − both nibbles (D[7:0]) are written into the device.
CY7C1143V18 − both bytes (D[17:0]) are written into the device.
L
L
–
L–H
–
L-H During the data portion of a write sequence:
CY7C1141V18 − both nibbles (D[7:0]) are written into the device.
CY7C1143V18 − both bytes (D[17:0]) are written into the device.
L
H
H
L
–
During the data portion of a write sequence:
CY7C1141V18 − only the lower nibble (D[3:0]) is written into the device, D[7:4] remains unaltered.
CY7C1143V18 − only the lower byte (D[8:0]) is written into the device, D[17:9] remains unaltered.
L
L–H During the data portion of a write sequence:
CY7C1141V18 − only the lower nibble (D[3:0]) is written into the device, D[7:4] remains unaltered.
CY7C1143V18 − only the lower byte (D[8:0]) is written into the device, D[17:9] remains unaltered.
H
H
L–H
–
–
During the data portion of a write sequence:
CY7C1141V18 − only the upper nibble (D[7:4]) is written into the device, D[3:0] remains unaltered.
CY7C1143V18 − only the upper byte (D[17:9]) is written into the device, D[8:0] remains unaltered.
L
L–H During the data portion of a write sequence:
CY7C1141V18 − only the upper nibble (D[7:4]) is written into the device, D[3:0] remains unaltered.
CY7C1143V18 − only the upper byte (D[17:9]) is written into the device, D[8:0] remains unaltered.
H
H
H
H
L–H
–
–
No data is written into the devices during this portion of a write operation.
L–H No data is written into the devices during this portion of a write operation.
The write cycle descriptions of CY7C1156V18 follows.[2, 10]
BWS0
K
L–H
–
K
Comments
L
L
–
During the data portion of a write sequence, the single byte (D[8:0]) is written into the device.
L–H During the data portion of a write sequence, the single byte (D[8:0]) is written into the device.
No data is written into the device during this portion of a write operation.
L–H No data is written into the device during this portion of a write operation.
H
H
L–H
–
–
Note
10. Is based on a Write cycle was initiated in accordance with the Write Cycle Description Truth Table. Alter NWS0, NWS1, BWS0, BWS1, BWS2, and BWS3 on different
portions of a Write cycle, as long as the setup and hold requirements are achieved.
Document Number: 001-06583 Rev. *D
Page 11 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
The write cycle descriptions of CY7C1145V18 follows.[2, 10]
BWS0 BWS1 BWS2 BWS3
K
K
Comments
L
L
L
L
L–H
–
During the data portion of a write sequence, all four bytes (D[35:0]) are written into
the device.
L
L
L
L
–
L–H
–
L–H During the data portion of a write sequence, all four bytes (D[35:0]) are written into
the device.
L
H
H
L
H
H
H
H
L
H
H
H
H
H
H
L
–
During the data portion of a write sequence, only the lower byte (D[8:0]) is written
into the device. D[35:9] remains unaltered.
L
L–H During the data portion of a write sequence, only the lower byte (D[8:0]) is written
into the device. D[35:9] remains unaltered.
H
H
H
H
H
H
L–H
–
–
During the data portion of a write sequence, only the byte (D[17:9]) is written into
the device. D[8:0] and D[35:18] remains unaltered.
L
L–H During the data portion of a write sequence, only the byte (D[17:9]) is written into
the device. D[8:0] and D[35:18] remains unaltered.
H
H
H
H
L–H
–
–
During the data portion of a write sequence, only the byte (D[26:18]) is written into
the device. D[17:0] and D[35:27] remains unaltered.
L
L–H During the data portion of a write sequence, only the byte (D[26:18]) is written into
the device. D[17:0] and D[35:27] remains unaltered.
H
H
L–H
–
–
During the data portion of a write sequence, only the byte (D[35:27]) is written into
the device. D[26:0] remains unaltered.
L
L–H During the data portion of a write sequence, only the byte (D[35:27]) is written into
the device. D[26:0] remains unaltered.
H
H
H
H
H
H
H
H
L–H
–
–
No data is written into the device during this portion of a write operation.
L–H No data is written into the device during this portion of a write operation.
Document Number: 001-06583 Rev. *D
Page 12 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Instruction Register
IEEE 1149.1 Serial Boundary Scan (JTAG)
Serially load three-bit instructions into the instruction register.
TDO pins as shown in “TAP Controller Block Diagram” on
page 16. Upon power up, the instruction register is loaded with
the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as described
in the previous section.
These SRAMs incorporate a serial boundary scan test access
port (TAP) in the FBGA package. This part is fully compliant with
IEEE Standard #1149.1-2001. The TAP operates using JEDEC
standard 1.8V IO logic levels.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are inter-
nally pulled up and may be unconnected. They may alternately
be connected to VDD through a pull up resistor. TDO must be left
unconnected. Upon power up, the device comes up in a reset
state which does not interfere with the operation of the device.
When the TAP controller is in the Capture IR state, the two least
significant bits are loaded with a binary “01” pattern to enable for
fault isolation of the board level serial test path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between TDI
and TDO pins. This enables data to be shifted through the SRAM
with minimal delay. The bypass register is set LOW (VSS) when
the BYPASS instruction is executed.
Test Access Port—Test Clock
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Boundary Scan Register
Test Mode Select
The boundary scan register is connected to all of the input and
output pins on the SRAM. Several no connect (NC) pins are also
included in the scan register to reserve pins for higher density
devices.
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to leave
this pin unconnected if the TAP is not used. The pin is pulled up
internally, resulting in a logic HIGH level.
The boundary scan register is loaded with the contents of the
RAM input and output ring when the TAP controller is in the
Capture-DR state and is then placed between the TDI and TDO
pins when the controller is moved to the Shift-DR state. Use the
EXTEST, SAMPLE/PRELOAD, and SAMPLE Z instructions to
Test Data-In (TDI)
The TDI pin is used to serially input information into the registers
and connect to the input of any of the registers. The register
between TDI and TDO is chosen by the instruction that is loaded
the instruction register, see “TAP Controller State Diagram” on
page 15 TDI is internally pulled up and unconnected if the TAP
is unused in an application. TDI is connected to the most signif-
icant bit (MSb) on any register.
The “Boundary Scan Order” on page 19 shows the order in which
the bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSb of the register is connected to
TDI, and the LSb is connected to TDO.
Identification (ID) Register
Test Data-Out (TDO)
The ID register is loaded with a vendor-specific 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in the “Identification Register Definitions”
on page 18.
The TDO output pin is used to serially clock data-out from the
registers. The output is active depending upon the current state
of the TAP state machine (see “Instruction Codes” on page 18).
The output changes on the falling edge of TCK. TDO is
connected to the least significant bit (LSb) of any register.
Performing a TAP Reset
A Reset is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This RESET does not affect the operation of the
SRAM and may be performed while the SRAM is operating. At
power up, the TAP is reset internally to ensure that TDO comes
up in a high-Z state.
TAP Instruction Set
instruction register. All combinations are listed in the “Instruction
Codes” on page 18. Three of these instructions are listed as
RESERVED and must not be used. The other five instructions
are described in this section.
TAP Registers
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO pins. To execute
the instruction after it is shifted in, the TAP controller must be
moved into the Update-IR state.
Registers are connected between the TDI and TDO pins and
enable data to be scanned into and out of the SRAM test circuitry.
Only one register can be selected at a time through the
instruction registers. Data is serially loaded into the TDI pin on
the rising edge of TCK. Data is output on the TDO pin on the
falling edge of TCK.
Document Number: 001-06583 Rev. *D
Page 13 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
IDCODE
PRELOAD enables an initial data pattern to be placed at the
latched parallel outputs of the boundary scan register cells
before the selection of another boundary scan test operation.
The IDCODE instruction causes a vendor-specific 32-bit code to
be loaded into the instruction register. It also places the
instruction register between the TDI and TDO pins and enables
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state. The IDCODE instruction is
loaded into the instruction register upon power up or whenever
the TAP controller is supplied a test logic reset state.
The shifting of data for the SAMPLE and PRELOAD phases can
occur concurrently when required—that is, while data captured
is shifted out, shift the preloaded data in.
BYPASS
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO pins. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
SAMPLE Z
The SAMPLE Z instruction causes the boundary scan register to
be connected between the TDI and TDO pins when the TAP
controller is in a Shift-DR state. The SAMPLE Z command puts
the output bus into a High-Z state until the next command is
supplied during the Update IR state.
EXTEST
The EXTEST instruction enables the preloaded data to be driven
out through the system output pins. This instruction also selects
the boundary scan register to be connected for serial access
between the TDI and TDO in the shift-DR controller state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the instruc-
tion register and the TAP controller is in the Capture-DR state, a
snapshot of data on the inputs and output pins is captured in the
boundary scan register.
EXTEST OUTPUT BUS TRI-STATE
IEEE Standard 1149.1 mandates that the TAP controller be able
to put the output bus into a tri-state mode.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because there
is a large difference in the clock frequencies, it is possible that
during the Capture-DR state, an input or output undergoes a
transition. The TAP may then try to capture a signal while in tran-
sition (metastable state). This does not harm the device, but
there is no guarantee as to the value that is captured. Repeat-
able results may not be possible.
The boundary scan register has a special bit located at bit
number 47. When this scan cell, called the “extest output bus
tri-state”, is latched into the preload register during the
Update-DR state in the TAP controller, it directly controls the
state of the output (Q-bus) pins, when the EXTEST is entered as
the current instruction. When HIGH, it enables the output buffers
to drive the output bus. When LOW, this bit places the output bus
into a High-Z condition.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture setup plus hold
times (tCS and tCH). The SRAM clock input might not be captured
correctly if there is no way in a design to stop (or slow) the clock
during a SAMPLE/PRELOAD instruction. If this is an issue, it is
still possible to capture all other signals and simply ignore the
value of the CK and CK captured in the boundary scan register.
Set this bit by entering the SAMPLE/PRELOAD or EXTEST
command, and then shifting the desired bit into that cell, during
the Shift-DR state. During Update-DR, the value loaded into that
shift-register cell latches into the preload register. When the
EXTEST instruction is entered, this bit directly controls the output
Q-bus pins. Note that this bit is preset HIGH to enable the output
when the device is powered up, and also when the TAP controller
is in the Test-Logic-Reset state.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO pins.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
Document Number: 001-06583 Rev. *D
Page 14 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
TAP Controller State Diagram
Figure 2. Tap Controller State Diagram[11]
TEST-LOGIC
1
RESET
0
1
1
1
TEST-LOGIC/
IDLE
SELECT
DR-SCAN
SELECT
IR-SCAN
0
0
0
1
1
CAPTURE-DR
CAPTURE-IR
0
0
SHIFT-DR
0
SHIFT-IR
0
1
1
EXIT1-DR
0
1
EXIT1-IR
0
1
0
0
PAUSE-DR
1
PAUSE-IR
1
0
0
EXIT2-DR
1
EXIT2-IR
1
UPDATE-DR
UPDATE-IR
1
1
0
0
Note
11. The 0/1 next to each state represents the value at TMS at the rising edge of TCK.
Document Number: 001-06583 Rev. *D
Page 15 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
TAP Controller Block Diagram
Figure 3. Tap Controller Block Diagram
0
Bypass Register
Selection
TDI
Selection
Circuitry
2
1
0
0
0
TDO
Circuitry
Instruction Register
29
31 30
.
.
2
1
Identification Register
.
106 .
.
.
2
1
Boundary Scan Register
TCK
TMS
TAP Controller
TAP Electrical Characteristics
The Tap Electrical Characteristics table over the operating range follows.[12, 13, 14]
Parameter Description Test Conditions
VOH1 Output HIGH Voltage IOH = −2.0 mA
Min
1.4
1.6
Max
Unit
V
VOH2
VOL1
VOL2
VIH
Output HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Input HIGH Voltage
IOH = −100 μA
IOL = 2.0 mA
IOL = 100 μA
V
0.4
0.2
V
V
0.65 VDD VDD + 0.3
V
VIL
Input LOW Voltage
–0.3
–5
0.35 VDD
5
V
IX
Input and Output Load Current
GND ≤ VI ≤ VDD
μA
Notes
12. These characteristic pertain to the TAP inputs (TMS, TCK, TDI and TDO). Parallel load levels are specified in the Electrical Characteristics table.
13. Overshoot: VIH(AC) < VDDQ + 0.35V (Pulse width less than tCYC/2), Undershoot: VIL(AC) > −0.3V (Pulse width less than tCYC/2).
14. All voltage refer to ground.
Document Number: 001-06583 Rev. *D
Page 16 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
TAP AC Switching Characteristics
The Tap AC Switching Characteristics over the operating range follows. [15, 16]
Parameter
tTCYC
Description
Min
Max
Unit
ns
TCK Clock Cycle Time
TCK Clock Frequency
TCK Clock HIGH
50
tTF
20
MHz
ns
tTH
20
20
tTL
TCK Clock LOW
ns
Setup Times
tTMSS
TMS Setup to TCK Clock Rise
TDI Setup to TCK Clock Rise
Capture Setup to TCK Rise
5
5
5
ns
ns
ns
tTDIS
tCS
Hold Times
tTMSH
tTDIH
TMS Hold after TCK Clock Rise
TDI Hold after Clock Rise
5
5
5
ns
ns
ns
tCH
Capture Hold after Clock Rise
Output Times
tTDOV
TCK Clock LOW to TDO Valid
TCK Clock LOW to TDO Invalid
10
ns
ns
tTDOX
0
TAP Timing and Test Condition
The Tap Timing and Test Conditions for the CY7C1141V18, CY7C1156V18, CY7C1143V18, and CY7C1145V18 follows.[16]
Figure 4. Tap Timing and Test Condition
0.9V
ALL INPUT PULSES
50Ω
1.8V
TDO
0.9V
0V
Z = 50
0
Ω
C = 20 pF
L
t
t
TH
TL
GND
(a)
Test Clock
TCK
t
TCYC
t
TMSH
t
TMSS
Test Mode Select
TMS
t
TDIS
t
TDIH
Test Data In
TDI
Test Data Out
TDO
t
TDOV
t
TDOX
Notes
15. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
16. Test conditions are specified using the load in TAP AC test conditions. tR/tF = 1 ns.
Document Number: 001-06583 Rev. *D
Page 17 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Identification Register Definitions
Value
Instruction Field
Description
CY7C1141V18
CY7C1156V18
000
CY7C1143V18
000
CY7C1145V18
Revision Number
(31:29)
000
000
Version number.
Cypress Device ID 11010010101000101 11010010101001101 11010010101010101 11010010101100101 Defines the type of
(28:12)
SRAM.
Cypress JEDEC ID
(11:1)
00000110100
1
00000110100
1
00000110100
1
00000110100
1
Enables unique
identification of
SRAM vendor.
ID Register
Presence (0)
Indicates the
presence of an ID
register.
Scan Register Sizes
Register Name
Bit Size
Instruction
Bypass
3
1
ID
32
107
Boundary Scan
Instruction Codes
Instruction
EXTEST
Code
000
Description
Captures the input and output ring contents.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI
and TDO. This operation does not affect SRAM operation.
SAMPLE Z
010
Captures the input and output contents. Places the boundary scan register between
TDI and TDO. This forces all SRAM output drivers to a High-Z state.
RESERVED
011
100
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
Captures the input and output ring contents. Places the boundary scan register
between TDI and TDO. This operation does not affect the SRAM operation.
RESERVED
RESERVED
BYPASS
101
110
111
Do not use: this instruction is reserved for future use.
Do not use: this instruction is reserved for future use.
Places the bypass register between TDI and TDO. This operation does not affect
SRAM operation.
Document Number: 001-06583 Rev. *D
Page 18 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Boundary Scan Order
Bit #
0
Bump ID
6R
Bit #
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
Bump ID
11H
10G
9G
Bit #
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
Bump ID
7B
6B
6A
5B
5A
4A
5C
4B
3A
1H
1A
2B
3B
1C
1B
3D
3C
1D
2C
3E
2D
2E
1E
2F
Bit #
81
Bump ID
3G
2G
1J
1
6P
82
2
6N
83
3
7P
11F
11G
9F
84
2J
4
7N
85
3K
3J
5
7R
86
6
8R
10F
11E
10E
10D
9E
87
2K
1K
2L
7
8P
88
8
9R
89
9
11P
10P
10N
9P
90
3L
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
91
1M
1L
10C
11D
9C
92
93
3N
3M
1N
2M
3P
2N
2P
1P
3R
4R
4P
5P
5N
5R
10M
11N
9M
94
9D
95
11B
11C
9B
96
9N
97
11L
11M
9L
98
10B
11A
Internal
9A
99
100
101
102
103
104
105
106
10L
11K
10K
9J
8B
7C
9K
6C
3F
10J
11J
8A
1G
1F
7A
Document Number: 001-06583 Rev. *D
Page 19 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Power Up Sequence in QDR-II+ SRAM
DLL Constraints
During Power Up, when the DOFF is tied HIGH, the DLL gets
locked after 2048 cycles of stable clock. QDR-II+ SRAMs must
be powered up and initialized in a predefined manner to prevent
undefined operations.
■ DLL uses K clock as its synchronizing input. The input must
have low phase jitter, which is specified as tKC Var
.
■ The DLL functions at frequencies down to 120 MHz.
■ If the input clock is unstable and the DLL is enabled, then the
DLL may lock onto an incorrect frequency, causing unstable
SRAM behavior. To avoid this, provide2048 cyclesstable clock
to relock to the desired clock frequency.
Power Up Sequence
■ ApplypowerwithDOFFtiedHIGH(allotherinputscanbeHIGH
or LOW)
❐ Apply VDD before VDDQ
❐ Apply VDDQ before VREF or at the same time as VREF
■ Provide stable power and clock (K, K) for 2048 cycles to lock
the DLL
Power Up Waveforms
Figure 5. Power Up Waveforms
K
K
Start Normal
Operation
Unstable Clock
> 2048 Stable Clock
is Stable)
Clock Start (Clock Starts after V /V
DD DDQ
V
/V
+
V
/V Stable (< 0.1V DC per 50 ns)
DD DDQ
DD DDQ
Fix HIGH (tie to V
DDQ
)
DOFF
Document Number: 001-06583 Rev. *D
Page 20 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Current into Outputs (LOW)......................................... 20 mA
Static Discharge Voltage (MIL-STD-883, M. 3015).. > 2001V
Latch up Current.................................................... > 200 mA
Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the
device. User guidelines are not tested.
Storage Temperature ................................ –65°C to + 150°C
Ambient Temperature with Power Applied. –55°C to + 125°C
Supply Voltage on VDD Relative to GND .......–0.5V to + 2.9V
Supply Voltage on VDDQ Relative to GND..... –0.5V to + VDD
DC Input Voltage[13].............................–0.5V to VDDQ + 0.3V
Operating Range
Ambient
[17]
[17]
Range
Commercial
Industrial
Temperature (TA)
VDD
VDDQ
0°C to +70°C
1.8 ± 0.1V
1.4V to
VDD
–40°C to +85°C
Electrical Characteristics
The DC Electrical Characteristics over the operating range follows. [14]
Parameter
VDD
Description
Power Supply Voltage
IO Supply Voltage
Test Conditions
Min
1.7
Typ
Max
Unit
1.8
1.5
1.9
V
V
VDDQ
VOH
1.4
VDD
Output HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Note 18
Note 19
VDDQ/2 – 0.12
VDDQ/2 – 0.12
VDDQ – 0.2
VSS
VDDQ/2 + 0.12
V
VOL
VDDQ/2 + 0.12
V
VOH(LOW)
VOL(LOW)
VIH
IOH = −0.1 mA, Nominal Impedance
VDDQ
V
IOL = 0.1 mA, Nominal Impedance
0.2
V
VREF + 0.1
–0.15
VDDQ + 0.15
V
VIL
Input LOW Voltage
VREF – 0.1
2
V
IX
Input Leakage Current
Output Leakage Current
Input Reference Voltage[20]
VDD Operating Supply
GND ≤ VI ≤ VDDQ
−2
μA
μA
V
IOZ
GND ≤ VI ≤ VDDQ, Output Disabled
Typical Value = 0.75V
−2
2
VREF
0.68
0.75
0.95
663
708
766
201
212
227
[21]
IDD
VDD = Max, IOUT = 0 mA, 300 MHz
mA
mA
mA
mA
mA
mA
f = fmax = 1/tCYC
333 MHz
375 MHz
ISB1
Automatic Power Down
Current
Max VDD
,
300 MHz
333 MHz
375 MHz
Both Ports Deselected,
VIN ≥ VIH or VIN ≤ VIL
f = fmax =1/tCYC
,
Inputs Static
AC Electrical Characteristics
The AC Electrical Characteristics over the operating range follows.[13]
Parameter
Description
Input HIGH Voltage
Input LOW Voltage
Test Conditions
Min
VREF + 0.2
–0.24
Typ
–
Max
Unit
V
VIH
VIL
VDDQ + 0.24
VREF – 0.2
–
V
Notes
17. Power up: Is based on a linear ramp from 0V to VDD(min) within 200 ms. During this time VIH < VDD and VDDQ < VDD
18. Output are impedance controlled. IOH = −(VDDQ/2)/(RQ/5) for values of 175Ω <= RQ <= 350Ω.
19. Output are impedance controlled. IOL = (VDDQ/2)/(RQ/5) for values of 175Ω <= RQ <= 350Ω.
20. VREF(min) = 0.68V or 0.46VDDQ, whichever is larger, VREF(max) = 0.95V or 0.54 VDDQ, whichever is smaller.
21. The operation current is calculated with 50% read cycle and 50% write cycle.
.
Document Number: 001-06583 Rev. *D
Page 21 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Capacitance
Tested initially and after any design or process change that may affect these parameters.
Parameter
CIN
Description
Input Capacitance
Test Conditions
Max
Unit
pF
TA = 25°C, f = 1 MHz,
5
6
7
V
DD = 1.8V
CCLK
Clock Input Capacitance
Output Capacitance
pF
VDDQ = 1.5V
CO
pF
Thermal Resistance
Tested initially and after any design or process change that may affect these parameters.
165 FBGA
Package
Parameter
Description
Test Conditions
Unit
ΘJA
Thermal Resistance
(junction to ambient)
Test conditions follow standard test methods and
procedures for measuring thermal impedance, in
accordance with EIA/JESD51.
13.48
°C/W
ΘJC
Thermal Resistance
(junction to case)
4.15
°C/W
AC Test Loads and Waveforms
Figure 6. AC Test Loads and Waveforms
V
= 0.75V
REF
0.75V
V
REF
V
0.75V
REF
R = 50
Ω
OUTPUT
[22]
ALL INPUT PULSES
1.25V
Z = 50
0
Ω
OUTPUT
Device
Under
Test
R = 50
Ω
L
0.75V
Device
Under
0.25V
5 pF
V
= 0.75V
Slew Rate = 2 V/ns
REF
ZQ
Test
ZQ
RQ =
RQ =
250Ω
250Ω
INCLUDING
JIG AND
SCOPE
(a)
(b)
Notes
22. Unless otherwise noted, test conditions are based on signal transition time of 2V/ns, timing reference levels of 0.75V, Vref = 0.75V, RQ = 250Ω, VDDQ = 1.5V, input
pulse levels of 0.25V to 1.25V, and output loading of the specified IOL/IOH and load capacitance shown in (a) of AC Test Loads.
Document Number: 001-06583 Rev. *D
Page 22 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Over the operating range[22, 23]
375 MHz
333 MHz
300 MHz
Cypress Consortium
Parameter Parameter
Description
Unit
Min Max Min Max Min Max
tPOWER
tCYC
tKH
VDD(Typical) to the First Access[24]
K Clock Cycle Time
1
–
1
–
1
–
ms
ns
tKHKH
tKHKL
tKLKH
tKHKH
2.66 8.40 3.0 8.40 3.3 8.40
Input Clock (K/K) HIGH
0.425
0.425
1.13
–
–
–
0.425
0.425
1.28
–
–
–
0.425
0.425
1.40
–
–
–
tCYC
tCYC
ns
tKL
Input Clock (K/K) LOW
tKHKH
K Clock Rise to K Clock Rise (rising edge to rising edge)
Setup Times
tSA
tAVKH
tIVKH
tIVKH
Address Setup to K Clock Rise
0.4
0.4
–
–
–
0.4
0.4
–
–
–
0.4
0.4
–
–
–
ns
ns
ns
tSC
Control Setup to K Clock Rise (RPS, WPS)
tSCDDR
Double Data Rate Control Setup to Clock (K, K) Rise
(BWS0, BWS1, BWS2, BWS3)
0.28
0.28
0.28
tSD
tDVKH
D[X:0] Setup to Clock (K/K) Rise
0.28
–
0.28
–
0.28
–
ns
Hold Times
tHA
tKHAX
tKHIX
tKHIX
Address Hold after K Clock Rise
0.4
0.4
–
–
–
0.4
0.4
–
–
–
0.4
0.4
–
–
–
ns
ns
ns
tHC
Control Hold after K Clock Rise (RPS, WPS)
tHCDDR
Double Data Rate Control Hold after Clock (K/K) Rise
(BWS0, BWS1, BWS2, BWS3)
0.28
0.28
0.28
tHD
tKHDX
D[X:0] Hold after Clock (K/K) Rise
0.28
–
0.28
–
0.28
–
ns
Output Times
tCO
tCHQV
K/K Clock Rise to Data Valid
–
0.45
–
–
0.45
–
–
0.45
–
ns
ns
tDOH
tCHQX
Data Output Hold after Output K/K Clock Rise
(Active to Active)
–0.45
–0.45
–0.45
tCCQO
tCQOH
tCQD
tCHCQV
tCHCQX
tCQHQV
tCQHQX
tCQHCQL
K/K Clock Rise to Echo Clock Valid
Echo Clock Hold after K/K Clock Rise
Echo Clock High to Data Valid
–
0.45
–
–
0.45
–
–
0.45
–
ns
ns
ns
ns
ns
ns
–0.45
–0.45
–0.45
0.2
–
0.2
–
0.2
–
tCQDOH
tCQH
Echo Clock High to Data Invalid
Output Clock (CQ/CQ) HIGH[25]
CQ Clock Rise to CQ Clock Rise[25]
–0.2
0.88
0.88
–0.2
1.03
1.03
–0.2
1.15
1.15
–
–
–
tCQHCQH tCQHCQH
–
–
–
(rising edge to rising edge)
tCHZ
tCLZ
tCHQZ
tCHQX1
tQVLD
Clock (K/K) Rise to Low-Z[26, 27]
Echo Clock High to QVLD Valid[28]
–
0.45
–
–
0.45
–
–
0.45
–
ns
ns
ns
–0.45
–0.45
–0.45
tQVLD
–0.20 0.20 –0.20 0.20 –0.20 0.20
DLL Timing
tKC Var tKC Var
tKC lock tKC lock
Clock Phase Jitter
–
0.20
–
–
0.20
–
–
0.20
–
ns
Cycles
ns
DLL Lock Time (K)
K Static to DLL Reset[29]
2048
30
2048
30
2048
30
tKC Reset tKC Reset
–
–
–
Notes
23. When a part with a maximum frequency above 300 MHz is operating at a lower clock frequency, it requires the input timings of the frequency range in which it is being
operated and outputs data with the output timings of that frequency range.
24. This part has a voltage regulator internally; tPOWER is the time that the power must be supplied above VDD minimum initially before a Read or Write operation can be
initiated.
25. These parameters are extrapolated from the input timing parameters (tKHKH – 250 ps, where 250 ps is the internal jitter. An input jitter of 200 ps (tKC Var) is already
included in the tKHKH). These parameters are only guaranteed by design and are not tested in production
26. tCHZ, tCLZ are specified with a load capacitance of 5 pF as in part (b) of AC Test Loads and Waveforms on page 22. Transition is measured ± 100 mV from steady-state
voltage.
27. At any voltage and temperature tCHZ is less than tCLZ and tCHZ less than tCO
.
28. tQVLD spec is applicable for both rising and falling edges of QVLD signal.
29. Hold to >VIH or <VIL
.
Document Number: 001-06583 Rev. *D
Page 23 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Switching Waveforms
Read/Write/Deselect Sequence
Figure 7. Waveform for 2.0 Cycle Read Latency [30, 31, 32]
NOP
1
READ
2
WRITE
3
READ
4
WRITE
5
NOP
6
7
8
K
t
t
t
t
KH
KL
CYC
KHKH
K
RPS
t
t
SC HC
t
t
SC
HC
WPS
A
A0
A1
A2
A3
t
t
HD
t
t
HD
SA HA
t
SD
t
SD
D10
D11
D12
D13
D30
D31
D32
D33
D
t
QVLD
t
QVLD
QVLD
t
DOH
t
t
CQDOH
CO
t
t
CHZ
t
CLZ
CQD
Q
Q22
Q01
Q02
Q23
Q00
t
Q03 Q20 Q21
(Read Latency = 2.0 Cycles)
CCQO
CQOH
CQ
CQ
CCQO
t
t
t
CQHCQH
CQH
CQOH
DON’T CARE
UNDEFINED
Notes
30. Q00 refers to output from address A0. Q01 refers to output from the next internal burst address following A0, i.e., A0+1.
31. Outputs are disabled (High-Z) one clock cycle after a NOP.
32. In this example, if address A2 = A1, then data Q20 = D10 and Q21 = D11. Write data is forwarded immediately as read results. This note applies to the whole diagram.
Document Number: 001-06583 Rev. *D
Page 24 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Ordering Information
Not all of the speed, package and temperature ranges are available. Contact your local sales representative or visit www.cypress.com
for actual products offered.
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Package Type
375 CY7C1141V18-375BZC
CY7C1156V18-375BZC
CY7C1143V18-375BZC
CY7C1145V18-375BZC
CY7C1141V18-375BZXC
CY7C1156V18-375BZXC
CY7C1143V18-375BZXC
CY7C1145V18-375BZXC
CY7C1141V18-375BZI
CY7C1156V18-375BZI
CY7C1143V18-375BZI
CY7C1145V18-375BZI
CY7C1141V18-375BZXI
CY7C1156V18-375BZXI
CY7C1143V18-375BZXI
CY7C1145V18-375BZXI
333 CY7C1141V18-333BZC
CY7C1156V18-333BZC
CY7C1143V18-333BZC
CY7C1145V18-333BZC
CY7C1141V18-333BZXC
CY7C1156V18-333BZXC
CY7C1143V18-333BZXC
CY7C1145V18-333BZXC
CY7C1141V18-333BZI
CY7C1156V18-333BZI
CY7C1143V18-333BZI
CY7C1145V18-333BZI
CY7C1141V18-333BZXI
CY7C1156V18-333BZXI
CY7C1143V18-333BZXI
CY7C1145V18-333BZXI
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
Commercial
Industrial
Commercial
Industrial
Document Number: 001-06583 Rev. *D
Page 25 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Ordering Information (continued)
Not all of the speed, package and temperature ranges are available. Contact your local sales representative or visit www.cypress.com
for actual products offered.
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Package Type
300 CY7C1141V18-300BZC
CY7C1156V18-300BZC
CY7C1143V18-300BZC
CY7C1145V18-300BZC
CY7C1141V18-300BZXC
CY7C1156V18-300BZXC
CY7C1143V18-300BZXC
CY7C1145V18-300BZXC
CY7C1141V18-300BZI
CY7C1156V18-300BZI
CY7C1143V18-300BZI
CY7C1145V18-300BZI
CY7C1141V18-300BZXI
CY7C1156V18-300BZXI
CY7C1143V18-300BZXI
CY7C1145V18-300BZXI
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
Commercial
Industrial
Document Number: 001-06583 Rev. *D
Page 26 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Package Diagram
Figure 8. 165-Ball FBGA (13 x 15 x 1.4 mm), 51-85180
BOTTOM VIEW
PIN 1 CORNER
TOP VIEW
Ø0.05 M C
Ø0.25 M C A B
-0.06
PIN 1 CORNER
Ø0.50
(165X)
+0.14
1
2
3
4
5
6
7
8
9
10
11
11 10
9
8
7
6
5
4
3
2
1
A
B
A
B
C
D
C
D
E
E
F
F
G
G
H
J
H
J
K
K
L
L
M
M
N
P
R
N
P
R
A
A
1.00
5.00
10.00
13.00 0.10
B
13.00 0.10
B
0.15(4X)
NOTES :
SOLDER PAD TYPE : NON-SOLDER MASK DEFINED (NSMD)
PACKAGE WEIGHT : 0.475g
JEDEC REFERENCE : MO-216 / DESIGN 4.6C
PACKAGE CODE : BB0AC
SEATING PLANE
C
51-85180-*A
Document Number: 001-06583 Rev. *D
Page 27 of 28
CY7C1141V18, CY7C1156V18
CY7C1143V18, CY7C1145V18
Document History Page
Document Title: CY7C1141V18/CY7C1156V18/CY7C1143V18/CY7C1145V18, 18-Mbit QDR™-II+ SRAM 4-Word Burst Archi-
tecture (2.0 Cycle Read Latency)
Document Number: 001-06583
Orig. of
Change
REV.
ECN No. Issue Date
Description of Change
**
430351
461654
See ECN
See ECN
NXR
New data sheet
*A
NXR
Revised the MPNs from
CY7C1156BV18 to CY7C1156V18
CY7C1143BV18 to CY7C1143V18
CY7C1145BV18 to CY7C1145V18
Changed tTH and tTL from 40 ns to 20 ns, changed tTMSS, tTDIS, tCS, tTMSH, tTDIH
,
t
CH from 10 ns to 5 ns and changed tTDOV from 20 ns to 10 ns in TAP AC
Switching Characteristics table
Modified Power Up waveform
*B
497629
See ECN
NXR
Changed the VDDQ operating voltage to 1.4V to VDD in the Features section, in
Operating Range table and in the DC Electrical Characteristics table
Added foot note in page 1
Changed the Maximum rating of Ambient Temperature with Power Applied from
–10°C to +85°C to –55°C to +125°C
Changed VREF (max) spec from 0.85V to 0.95V in the DC Electrical Character-
istics table and in the note below the table
Updated foot note 22 to specify Overshoot and Undershoot Spec
Updated ΘJA and ΘJC values
Removed x9 part and its related information
Updated footnote 25
*C
1167806
See ECN VKN/KKVTMP Converted from preliminary to final
Added x8 and x9 parts
Changed IDD values from 766 mA to 1020 mA for 375 MHz, 708 mA to 920 mA
for 333 MHz, 663 mA to 850 mA for 300 MHz
Changed ISB values from 227 mA to 290 mA for 375 MHz, 212 mA to 260 mA
for 333 MHz, 201 mA to 250 mA for 300 MHz
Changed tCYC(max) spec to 8.4 ns for all speed bins
Changed ΘJA value from 13.48 °C/W to 17.2 °C/W
Updated Ordering Information table
*D
2199066 See ECN
VKN/AESA Added footnote# 21 related to IDD
© Cypress Semiconductor Corporation, 2006-2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-06583 Rev. *D
Revised March 06, 2008
Page 28 of 28
QDR™ is a trademark of Cypress Semiconductor Corp. QDR RAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress, IDT, NEC, Renesas, and Samsung. All
product and company names mentioned in this document are the trademarks of their respective holders.
|