CY7C1019D
1-Mbit (128K x 8) Static RAM
Features
Functional Description [1]
• Pin- and function-compatible with CY7C1019B
• High speed
The CY7C1019D is a high-performance CMOS static RAM
organized as 131,072 words by 8 bits. Easy memory
expansion is provided by an active LOW Chip Enable (CE), an
active LOW Output Enable (OE), and tri-state drivers. This
device has an automatic power-down feature that significantly
reduces power consumption when deselected. The eight input
— t = 10 ns
AA
• Low active power
— I = 80 mA @ 10 ns
CC
and output pins (IO through IO ) are placed in
high-impedance state when:
a
0
7
• Low CMOS standby power
— I
= 3 mA
SB2
• Deselected (CE HIGH)
• 2.0V Data retention
• Outputs are disabled (OE HIGH)
• Automatic power-down when deselected
• CMOS for optimum speed/power
• Center power/ground pinout
• When the write operation is active (CE LOW, and WELOW).
Write to the device by taking Chip Enable (CE) and Write
Enable (WE) inputs LOW. Data on the eight IO pins (IO
0
through IO ) is then written into the location specified on the
7
• Easy memory expansion with CE and OE options
• Functionally equivalent to CY7C1019B
address pins (A through A ).
0
16
Read from the device by taking Chip Enable (CE) and Output
Enable (OE) LOW while forcing Write Enable (WE) HIGH.
Under these conditions, the contents of the memory location
specified by the address pins appears on the IO pins.
• Available in Pb-free 32-pin 400-Mil wide Molded SOJ and
32-pin TSOP II packages
Logic Block Diagram
IO
0
INPUT BUFFER
IO
1
A
0
IO
2
A
1
A
2
128K x 8
IO
3
A
3
A
4
ARRAY
IO
4
A
5
A
6
IO
5
A
7
A
8
IO
6
CE
IO
POWER
DOWN
7
COLUMN DECODER
WE
OE
Note
1. For guidelines on SRAM system design, please refer to the ‘System Design Guidelines’ Cypress application note, available on the internet at www.cypress.com.
Cypress Semiconductor Corporation
Document #: 38-05464 Rev. *E
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised February 22, 2007
CY7C1019D
Current into Outputs (LOW) ........................................ 20 mA
Maximum Ratings
Static Discharge Voltage........................................... > 2001V
(per MIL-STD-883, Method 3015)
Exceeding the maximum ratings may impair the useful life of
the device. These user guidelines are not tested.
Latch-up Current .................................................... > 200 mA
Storage Temperature .................................–65°C to +150°C
Ambient Temperature with
Operating Range
Power Applied.............................................–55°C to +125°C
[2]
Ambient
Temperature
Supply Voltage on V to Relative GND ... –0.5V to +6.0V
CC
Range
V
Speed
CC
DC Voltage Applied to Outputs
[2]
Industrial
–40°C to +85°C
5V ± 0.5V
10 ns
in High-Z State ...................................–0.5V to V + 0.5V
CC
[2]
DC Input Voltage ................................–0.5V to V + 0.5V
CC
Electrical Characteristics (Over the Operating Range)
–10 (Industrial)
Parameter
Description
Test Conditions
Unit
Min
Max
V
Output HIGH Voltage
I
I
= –4.0 mA
2.4
V
V
OH
OL
IH
OH
V
V
V
I
Output LOW Voltage
Input HIGH Voltage
= 8.0 mA
0.4
OL
2.2
–0.5
–1
V
+ 0.5
V
CC
[2]
Input LOW Voltage
0.8
+1
+1
80
72
58
37
10
V
IL
Input Leakage Current
Output Leakage Current
GND < V < V
CC
µA
µA
mA
mA
mA
mA
mA
IX
I
I
I
GND < V < V , Output Disabled
–1
OZ
I
CC
V
Operating Supply Current
V
= Max,
100 MHz
83 MHz
66 MHz
40 MHz
CC
CC
CC
I
= 0 mA,
OUT
f = f
= 1/t
max
RC
I
I
Automatic CE Power-Down
Current—TTL Inputs
Max V , CE > V
CC IH
V
SB1
SB2
> V or V < V , f = f
IN
IH IN IL max
Automatic CE Power-Down
Current—CMOS Inputs
Max V , CE > V – 0.3V,
V
3
mA
CC
CC
> V – 0.3V, or V < 0.3V, f = 0
IN
CC IN
Note
2.
V
(min) = –2.0V and V (max) = V + 1V for pulse durations of less than 5 ns.
IH CC
IL
Document #: 38-05464 Rev. *E
Page 3 of 11
CY7C1019D
Capacitance [3]
Parameter
Description
Input Capacitance
Output Capacitance
Test Conditions
Max
6
Unit
pF
C
C
T = 25°C, f = 1 MHz, V = 5.0V
CC
IN
A
8
pF
OUT
Thermal Resistance [3]
400-Mil
Wide SOJ
Parameter
Description
Test Conditions
TSOP II
Unit
Θ
Thermal Resistance
(Junction to Ambient)
Still Air, soldered on a 3 × 4.5 inch,
four-layer printed circuit board
56.29
62.22
°C/W
JA
Θ
Thermal Resistance
(Junction to Case)
38.14
21.43
°C/W
JC
AC Test Loads and Waveforms [4]
ALL INPUT PULSES
3.0V
Z = 50Ω
90%
10%
90%
10%
OUTPUT
50Ω
GND
30 pF*
* CAPACITIVE LOAD CONSISTS
OF ALL COMPONENTS OF THE
TEST ENVIRONMENT
1.5V
Fall Time: ≤ 3 ns
Rise Time: ≤ 3 ns
(b)
(a)
High-Z characteristics:
R1 480Ω
5V
OUTPUT
R2
255Ω
5 pF
INCLUDING
JIG AND
SCOPE
(c)
Notes
3. Tested initially and after any design or process changes that may affect these parameters.
4. AC characteristics (except High-Z) are tested using the load conditions shown in Figure (a). High-Z characteristics are tested for all speeds using the test load
shown in Figure (c).
Document #: 38-05464 Rev. *E
Page 4 of 11
CY7C1019D
[5]
Switching Characteristics (Over the Operating Range)
–10 (Industrial)
Min Max
Parameter
Description
Unit
Read Cycle
[6]
t
V
(typical) to the first access
100
10
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
power
CC
t
t
t
t
t
t
t
t
t
t
t
Read Cycle Time
RC
Address to Data Valid
10
AA
Data Hold from Address Change
CE LOW to Data Valid
OE LOW to Data Valid
OE LOW to Low Z
3
OHA
ACE
DOE
LZOE
HZOE
LZCE
HZCE
10
5
0
3
0
[7, 8]
OE HIGH to High Z
5
5
[8]
CE LOW to Low Z
[7, 8]
CE HIGH to High Z
[9]
CE LOW to Power-Up
PU
[9]
CE HIGH to Power-Down
10
PD
[10, 11]
Write Cycle
t
t
t
t
t
t
t
t
t
t
Write Cycle Time
10
7
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
WC
CE LOW to Write End
SCE
AW
Address Set-Up to Write End
Address Hold from Write End
Address Set-Up to Write Start
WE Pulse Width
7
0
HA
0
SA
7
PWE
SD
Data Set-Up to Write End
Data Hold from Write End
6
0
HD
[8]
WE HIGH to Low Z
3
LZWE
HZWE
[7, 8]
WE LOW to High Z
5
Notes
5. Test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V, and output loading of the specified
I
t
t
/I and 30-pF load capacitance.
OL OH
6.
7.
gives the minimum amount of time that the power supply should be at typical V values until the first memory access can be performed.
CC
POWER
[4]
, t
, and t
are specified with a load capacitance of 5 pF as in (c) of “AC Test Loads and Waveforms ” on page 4. Transition is measured when the outputs enter a
HZOE HZCE
HZWE
high impedance state.
8. At any given temperature and voltage condition, t
is less than t
, t
is less than t
, and t
is less than t
for any given device.
HZCE
LZCE HZOE
LZOE
HZWE
LZWE
9. This parameter is guaranteed by design and is not tested.
10. The internal write time of the memory is defined by the overlap of CE LOW and WE LOW. CE and WE must be LOW to initiate a write, and the transition of any of
these signals can terminate the write. The input data set-up and hold timing should be referenced to the leading edge of the signal that terminates the write.
11. The minimum write cycle time for Write Cycle no. 3 (WE controlled, OE LOW) is the sum of t
and t
.
HZWE
SD
Document #: 38-05464 Rev. *E
Page 5 of 11
CY7C1019D
Data Retention Characteristics (Over the Operating Range)
Parameter
Description
Conditions
Min
Max
Unit
V
V
V
for Data Retention
2.0
DR
CC
I
Data Retention Current
V
V
= V = 2.0V, CE > V – 0.3V,
3
mA
CCDR
CC
DR
CC
> V – 0.3V or V < 0.3V
IN
CC
IN
[3]
t
t
Chip Deselect to Data Retention Time
Operation Recovery Time
0
ns
ns
CDR
[12]
t
R
RC
Data Retention Waveform
DATA RETENTION MODE
DR > 2V
4.5V
4.5V
V
V
CC
t
t
R
CDR
CE
Switching Waveforms
[13, 14]
Read Cycle No. 1 (Address Transition Controlled)
tRC
ADDRESS
t
AA
t
OHA
DATA OUT
PREVIOUS DATA VALID
DATA VALID
[14, 15]
Read Cycle No. 2 (OE Controlled)
ADDRESS
CE
t
RC
t
ACE
OE
t
HZOE
t
DOE
t
HZCE
t
LZOE
HIGH
IMPEDANCE
HIGH IMPEDANCE
DATA OUT
DATA VALID
t
LZCE
t
PD
V
CC
ICC
t
PU
SUPPLY
CURRENT
50%
50%
ISB
Notes
12. Full device operation requires linear V ramp from V to V
> 50 µs or stable at V > 50 µs.
CC(min)
CC
DR
CC(min)
13. Device is continuously selected. OE, CE = V .
IL
14. WE is HIGH for Read cycle.
15. Address valid prior to or coincident with CE transition LOW.
Document #: 38-05464 Rev. *E
Page 6 of 11
CY7C1019D
Switching Waveforms (continued)
[16, 17]
Write Cycle No. 1 (CE Controlled)
t
WC
ADDRESS
CE
t
SCE
t
SA
t
SCE
t
t
HA
AW
t
PWE
WE
t
t
HD
SD
DATA IO
DATA VALID
[16, 17]
Write Cycle No. 2 (WE Controlled, OE HIGH During Write)
t
WC
ADDRESS
t
SCE
CE
t
t
HA
AW
t
t
PWE
SA
WE
OE
t
t
SD
HD
DATA VALID
DATA IO
IN
NOTE 18
t
HZOE
Notes
16. Data IO is high impedance if OE = V
.
IH
17. If CE goes HIGH simultaneously with WE going HIGH, the output remains in a high-impedance state.
18. During this period the IOs are in the output state and input signals should not be applied.
Document #: 38-05464 Rev. *E
Page 7 of 11
CY7C1019D
Switching Waveforms (continued)
[11, 17]
Write Cycle No. 3 (WE Controlled, OE LOW)
t
WC
ADDRESS
CE
t
SCE
t
t
HA
AW
t
SA
t
PWE
WE
t
t
HD
SD
DATA IO
NOTE 18
DATA VALID
t
t
LZWE
HZWE
Truth Table
CE
H
L
OE
WE
X
IO –IO
Mode
Power
0
7
X
L
High Z
Power-Down
Read
Standby (I
)
SB
H
Data Out
Data In
High Z
Active (I
Active (I
Active (I
)
CC
L
X
H
L
Write
)
CC
L
H
Selected, Outputs Disabled
)
CC
Ordering Information
Speed
Package
Diagram
Operating
Range
Ordering Code
CY7C1019D-10VXI
CY7C1019D-10ZSXI
Package Type
(ns)
10
51-85033 32-pin (400-Mil) Molded SOJ (Pb-free)
51-85095 32-pin TSOP Type II (Pb-free)
Industrial
Please contact your local Cypress sales representative for availability of these parts.
Document #: 38-05464 Rev. *E
Page 8 of 11
CY7C1019D
Package Diagrams
Figure 1. 32-pin (400-Mil) Molded SOJ (51-85033)
51-85033-*B
Document #: 38-05464 Rev. *E
Page 9 of 11
CY7C1019D
Package Diagrams (continued)
Figure 2. 32-pin Thin Small Outline Package Type II (51-85095)
51-85095-**
All product or company names mentioned in this document may be the trademarks of their respective holders.
Document #: 38-05464 Rev. *E
Page 10 of 11
© Cypress Semiconductor Corporation, 2006-2007. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for
the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended
to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
CY7C1019D
Document History Page
Document Title: CY7C1019D, 1-Mbit (128K x 8) Static RAM
Document Number: 38-05464
Orig. of
Change
REV.
ECN NO.
Issue Date
Description of Change
**
201560
233715
See ECN
See ECN
SWI
Advance Information data sheet for C9 IPP
*A
RKF
DC parameters are modified as per EROS (Spec # 01-2165)
Pb-free offering in the Ordering Information
*B
262950
See ECN
RKF
Added T
Spec in Switching Characteristics table
power
Added Data Retention Characteristics table and waveforms
Shaded Ordering Information
*C
*D
307598
520647
See ECN
See ECN
RKF
VKN
Reduced Speed bins to -10 and -12 ns
Converted from Preliminary to Final
Removed Commercial Operating range
Removed 12 ns speed bin
Added I values for the frequencies 83MHz, 66MHz and 40MHz
CC
Updated Thermal Resistance table
Updated Ordering Information Table
Changed Overshoot spec from V +2V to V +1V in footnote #2
CC
CC
*E
802877
See ECN
VKN
Changed I spec from 60 mA to 80 mA for 100MHz, 55 mA to 72 mA
for 83MHz, 45 mA to 58 mA for 66MHz, 30 mA to 37 mA for 40MHz
CC
Document #: 38-05464 Rev. *E
Page 11 of 11
|