®
ELECT RO N ICS CO RP.
LCM5043NP & LCM5643NP
Remote Controlled Color Display Monitor
with Headphone Jack
Installation and Owner's Manual
SYSTEM OVERVIEW
The LCM5043NP is comprised of a 5" Thin Film Transistor (TFT) Liq-
uid Crystal Display ( LCD) Monitor. The LCM5643NP is comprised of a
5.6" Thin Film Transistor (TFT) Liquid Crystal Display ( LCD) Monitor.
The Monitor for both of these systems have a 4:3 Aspect Ratio display
that allows the user to select between two video sources (Not Sup-
plied). The Monitors displays all functions with the comprehensive On
Screen Display (OSD). Can be used with an optional Wired Head-
phone.
OPTIONAL AUDIO CONNECTION
1) Wired Headphones......................................... P/N=HP275
Wired Headphones
2
MATERIALS LIST
1. System Monitor (LCM5043NP=136C2187) or (LCM5643NP=136C2186) (1pc.)
2. Remote Control Unit (136B2156) with Lithium Battery, 3V,CR 2025
3. Interconnect Box (136B2183)
(1pc.)
(1pc.)
(1pc.)
4. Monitor Cable, 8' (112B3152)
5. Headrest Mounting Tray (LCM5043NP=102C3740)
or (LCM5643NP=102C3742)
(1pc.)
6. Trim Ring for Mounting Tray (LCM5043NP=102B3741)
or (LCM5643NP=102B3743)
(1pc.)
7. Power Cable, 2.46' (112B3127)
8. Removal Tool (108B3632)
(1pc.)
(1pc.)
1
2
3
6
5
8
4
7
4
VEHICLE PREPARATION
1) Decide on the system configuration and the options that will be in-
stalled (i.e. what components, VCP, DVD, TV Tuner, Video Game,
Monitor, FM Modulator, etc.).
2) Read the manuals and get familiar with the electrical requirements
andconnections.
3) Decideonthemountinglocationsandmethodsofmountingtheprod-
ucts.
4) Prepare the vehicle by removing any interior trim necessary to gain
accesstothevehicle'swiringaswellasallareaswhereinterconnect-
ingwireharnesseswillbelocated. Ifanyaccessholesneedtobecut
into the vehicle, headrests, or other trim components, this should be
performednow. (RefertotheInstallationProcedure).
5) Runthewiringharnessesandcablingthroughoutthevehicleasnec-
essary. (Refertothewiringinstructionsfortheindividualcomponents
and accessory options being installed). Be sure, that all the wiring is
protectedfromsharpedgesandisroutedinsuchamannerthatitwill
not be pinched, when it is fully installed. Be sure to leave enough
slack in the wiring at each component to allow sufficient working
room.
6) Remove all the A/V system components from their packaging and
then place them in the vehicle at their respective locations.
7) Locateanaccessorypowersource(RedWire)(+12VDCpresentwhen
the ignition key is in the accessory and run positions. 0VDC should
be present, when the ignition key is in the OFF position). Generally,
these wires can be found at the ignition switch or fuse box.
8) Locate a Constant Power Source (Yellow Wire)(+12VDC present at
all times).
NOTE: Ensure that the accessory power is fused at the source.
Failure to do so may result in vehicle wiring damage.) Ground the
black wire to a chassis ground close to the mounting location of AV
sources.
9) Connectallthecomponentstogether(electrically)andverifythatthe
proper operation of all the system functions. NOTE: This is best
doneBEFOREthecomponentsarepermanentlymounted.
4
10) After verifying the proper operation of the system, proceed to mount
each component.
11) The mounting method, and the location will vary from vehicle to
vehicle, so this manual will only focus for the installation of the
12) The best location for the system components is:
a) Monitor: Headrest or bracket (optional) mounted onto a flat
surface.
b) System Interconnection Box (AVX-6869): In line with all
the system cabling and in an area were it can be easily ac-
cessed.
c) System Main Cable: Under either seat where monitors
are located.
Tools and Materials Required:
Utility knife or box cutter with sharp blade.
Permanent Marker.
Tie Wraps.
INSTALLATION
Optional Bracket Mounting:
This procedure describes mounting the system monitor using an op-
tional Surface Mount Bracket (sold separately, # FB1)
1) Start by firmly attaching the Surface Mount Bracket onto a flat
surface
IMPORTANT NOTICE
It is unlawful in most jurisdictions to drive a motor vehicle which is
equipped with a television viewer or screen that is located at the point
forward of the back of the driver’s seat, or that is visible directly or indi-
rectly, to the driver while operating the vehicle.
5
2) Slide monitor onto Surface Mount Bracket and then tighten the
fasten wheel.
Monitor
Fastener Wheel
Surface Mount Fastener
Mounting Bracket
3) Adjust viewing angle of monitor by tightening the fastener at the
side.
Surface Mount
4) When the system components are mounted, test the system to
verify that it is functioning correctly. Make sure that no wiring was
pinched, or connected improperly during the final installation.
6
Headrest Mounting:
Mounting
Tray
Trim
Ring
1) Remove the headrest from the
vehicle for easiest installation.
Monitor
Headrest
2) Lay headrest on a flat surface.
3) Center trim collar on headrest
as shown.
NOTE: Depending on the angle of
the headrest the Trim Ring and
housing may be mounted upside
down.
4) Using a Permanent Marker,
mark headrest material along
the interior of the Trim Ring.
5) Remove the Trim Ring and
mark an “X” from corner to cor-
ner as shown.
7
6) Using the utility knife, cut the
headrest material along the “X”
lines. Do not cut the material
along the other lines at this time.
7) This will leave you with an “X” cut
as shown.
8) Pull the flaps up and cut the foam
beneath the material to the proper
depth. Cut all four sides of the
foam.
9) Using your fingers, tear the foam
out of the headrest leaving a re-
cess where the shell will be in-
serted.
NOTE: At this point you will need to
install the harness up through the area
into the recess. It may be helpful to
follow one of the posts and tie wrap it
to the post for restraint.
8
10) Lay the flaps of headrest mate-
rial down into the recess and in-
sert the Mounting Tray into the
recess. Check for fit. If it does
not fit properly, you may need to
remove some more foam.
NOTE: The Mounting Tray will need
to be secured to the headrest, either
by using tie straps, screws, ect..
11) Guide the cable through the side
opening of the Mounting Tray and
plug it into the Monitor. Make
sure the connector locks into
place. Insert the Monitor into the
Mounting Tray and secure the
cable using tie wraps or screws
12) Turn the Monitor around and in-
sert it into the Mounting Tray
housing. Snap into place.
13) Connect the Monitor power input
plug to a DC power source (Red
plug +12 VDC, Yellow plug +12
VDC Constant and Black plug (-)
to ground).
14) Connect the external video
source output signal (from VCP/
DVD, TV Etc.) to the VIDEO IN
jack. Test the system to verify
proper installation.
9
ELECTRICAL CONNECTION (Wiring Diagram)
AV Output
Video Source
Input (1&2)
Not Used
10
Monitor Removal:
The following procedure is to remove the Monitor from the Mounting
Tray using the supplied Removal Tool. NOTE: Use care when per-
forming this procedure not to scratch any exposed surfaces with the
edges of the Removal Tool. Masking tape applied to the two tips or
legs of the Removal Tool will help prevent scratching.
1) LocatetheRemovalToolandapplytape
1
to the tips.
Removal
Tool
2) Insert the Removal Tool into the cen-
Removal Tool
2
ter of the space between the top outer
Mounting Tray and the Monitor. You
will hear click(s) when inserted cor-
rectly. This will disengage the two
pressure latches holding the monitor
in place.
Removal
Tool
3) While applying upwardly pressure, pull 3
the Removal Tool out and up.
4) The Monitor will pop out from the top
4
and can be removed by detaching the
Monitor Cable.
Monitor
Cable
11
CONTROLS AND INDICATORS
Headphone
OPERATION
1. Press power On/Off button to the On position. The LED power
indicator will light red.
2. Press the Picture Select button to adjust the picture display
characteristics. The adjustments will be shown on the On
Screen Display in the following sequence: Contrast, Brightness,
Color, and TINT.
3. While in the video adjustment mode, press the up button to
increase the selected adjustment level or press the down but-
ton to decrease the level.
12
MAINTENANCE
To avoid electrical shock, do not open the enclosure. High voltage
is present. No user serviceable parts inside the enclosure.
Do not use any chemical solvent, cleaning agent or corrosive de-
tergent to clean away dirt on the surface of the screen. To clean off
dirt or fingerprint, we recommend the use of a soft damp lens clean-
ing cloth.
Should there be requirement to replace blown fuse, do remember
to disconnect all power supply and switched off the unit before
replacing it with a new one. Only use fuse’s with a correct rating to
avoid damaging the unit.
13
REMOTE CONTROLLER
NOTE: The Remote Controller supplied with this system is a stan-
dard remote control, which is used to operate other systems. The
Remote Controller is not a universal remote and will only perform
the functions described herein. Only the Keys highlighted on the
Remote Controller image bellow are used to operate this system.
Functional Remote Controller Keys
POWER ON/OFF
UP ADJUSTMENT
DOWN ADJUSTMENT
MODE SELECTION
MENU (ACTIVATION of
OSD and FUNCTION
SELECTION)
14
MENU FUNCTION KEY:
The MENU Key is used to navigate between the Color, Brightness and
Tint adjustment modes. When the MENU Key is pressed an On Screen
Display(OSD) will appear as shown bellow.
OSD
Press release and tap the MENU Key
until the desired adjustment mode is
selected. To return to the original set-
tings select the RESET.
When an adjustment mode is
selected, press and hold the either
the p or q (CH/DISK/SET) Key until
the desired setting is reached.
Using the p Key
Using the q Key
15
VIDEO SOURCE MODE KEY:
To switch between Video Input Sources (AV1 and AV2) press and
release the MODE Key.
NOTE:
For the LCM5643NP - Select
either *NTSC or PAL, press
the p or q Keys (CH/DISK/SET).
VOLUME CONTROL KEY:
To increase or decrease the Volume, press and hold the VOL p or q
Key until the desired volume is reached.
16
Replacement of Remote Controller Battery:
1. Use a small coin to pry open battery holder from compartment.
2. Remove old battery and put in a new one with positive sign “ + “
facing upward.
3. Push compartment into position.
Precaution:
1. Dispose off used battery properly.
2. Do not misuse battery by short - circuiting the “ + “ and “ - “
terminal or put it into fire.
3. Remove used battery from compartment to prevent leakage from
damaged battery.
4. To avoid accident, do prevent children from playing with the bat-
tery.
17
SPECIFICATIONS
LCM5043NP:
LCD Panel Size (Diagonal) ................................... 5"
LCD Panel Format ................................................. 960 x 234 dots
LCD Panel Resolution ........................................... 224,640 pixels
LCD Backlight Life ................................................. 10,000 hrs
Image Aspect Ratio ............................................... 4:3
Video Input Signal .................................................. NTSC Composite Video
Power Source ....................................................... +12V
Power Consumption ............................................. 10W
Operating Temperature ......................................... 0 C to 60 C
Storage Temperature ............................................. -20 C to 80 C
Weight .................................................................. 0.259 kg
Dimensions .......................................................... 13.8 x 9.8 x 2.8 cm
LCM5643NP:
LCD Panel Size (Diagonal) ................................... 5.6"
LCD Panel Format ................................................. 960 x 234 dots
LCD Panel Resolution ........................................... 224,640 pixels
LCD Backlight Life ................................................. 10,000 hrs
Image Aspect Ratio ............................................... 4:3
Video Input Signal .................................................. NTSC Composite Video
Power Source ....................................................... +12V
Power Consumption ............................................. 10W
Operating Temperature ......................................... 0 C to 60C
Storage Temperature ............................................. -20 C to 80 C
Weight .................................................................. 0.343 kg
Dimensions .......................................................... 15.1 x 10.8 x 3.1 cm
18
36 MONTH LIMITED WARRANTY
Applies to Audiovox Mobile Video Products
AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser
of this product that should this product or any part thereof, under normal use and conditions,
be proven defective in material or workmanship within 36 months from the date of original
purchase, such defect(s) will be repaired or replaced with reconditioned product (at the
Company's option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered
with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s),
transportation prepaid, to the Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or noise, to
correction of antenna problems, to costs incurred for installation, removal or reinstallation of
theproduct, ortodamagetotapes, discs, speakers, accessories, orvehicleelectricalsystems.
This Warranty does not apply to any product or part thereof which, in the opinion of the
Company,hassufferedorbeendamagedthroughalteration,improperinstallation,mishandling,
misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code
label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS
LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT,
SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PUR-
CHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL
BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR
BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITYMUSTBEBROUGHTWITHINAPERIODOF48MONTHSFROMDATE
OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is
authorized to assume for the Company any liability other than expressed herein in connection
with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion
or limitation of incidental or consequential damage so the above limitations or exclusions may
not apply to you. This Warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
U.S.A.:AUDIOVOXELECTRONICSCorp.,150MARCUSBLVD.,HAUPPAUGE,NY11788 1-800-645-4994
CANADA : CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
© 2002 Audiovox Electronics Corp., Hauppauge, NY
128-6323
|