AKG Acoustics CS 5 User Manual
CS 5  
Conference System  
User Manual  
Please read before using the equipment!  
Table of Contents  
Page  
Section 6: CS 5 IU Interpreter Station.............................................................................................................................30  
6.1 General.....................................................................................................................................................................30  
6.2 Control Panel, Inputs and Outputs...............................................................................................................................30  
6.3 Setting Up.................................................................................................................................................................31  
6.3.1 Making Connections.................................................................................................................................................31  
6.3.2 Selecting Station Addresses..............................................................................................................................32  
6.3.3 Selecting Target Language Channels.........................................................................................................................32  
6.3.4 List of Available Language Names .....................................................................................................................33  
6.3.5 Selecting the Microphone Type..........................................................................................................................33  
6.4 Using the Interpreter Station.......................................................................................................................................34  
Section 7: Infrared Transmission System.............................................................................................................................36  
7.1 CS 5 IRT 1 and CS 5 IRT 2 Infrared Radiators..............................................................................................................36  
7.1.1 General............................................................................................................................................................36  
7.1.2 Placement .......................................................................................................................................................36  
7.1.3 Mounting .........................................................................................................................................................37  
7.1.4 Connections.....................................................................................................................................................37  
7.2 CS 5 IRR 7 Infrared Receiver......................................................................................................................................38  
7.2.1 General............................................................................................................................................................38  
7.2.2 Using the Infrared Receiver ...............................................................................................................................39  
7.2.3 Replacing Batteries...........................................................................................................................................39  
7.3 CS 5 CU 50 Charger/Storage Case.............................................................................................................................40  
7.3.1 General............................................................................................................................................................40  
7.3.2 Charging Batteries............................................................................................................................................40  
7.3.3 Battery Care.....................................................................................................................................................41  
Section 8: System Components ...........................................................................................................................................42  
Section 9: Specifications .....................................................................................................................................................43  
9.1 CS 5 BU....................................................................................................................................................................43  
9.1.1 General............................................................................................................................................................43  
9.1.2 Connector Pinouts............................................................................................................................................44  
9.2 CS 5 DU/VU ..............................................................................................................................................................46  
9.2.1 General............................................................................................................................................................46  
9.2.2 Connector Pinouts............................................................................................................................................46  
9.3 CS 5 IU.....................................................................................................................................................................47  
9.3.1 General............................................................................................................................................................47  
9.3.2 Connector Pinouts............................................................................................................................................47  
9.4 CS 5 PS 12...............................................................................................................................................................48  
9.5 CS 5 IRT 1 and CS 5 IRT 2.........................................................................................................................................49  
9.6 CS 5 IRR 7................................................................................................................................................................49  
9.7 CS 5 CU 50...............................................................................................................................................................50  
9.8 Conformity................................................................................................................................................................50  
CS 5 User Manual  
- 3 -  
Symbols Used  
The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within  
the equipment.  
The exclamation point in an equilateral triangle on the equipment indicates that it is necessary for the user to refer to  
the User Manual or Quickstart Guide.  
In the User Manual and Quickstart Guide, this symbol marks instructions that the user must follow to ensure safe op-  
eration of the equipment.  
!
The "ꢀ" symbol marks important notes, hints, or explanations that make it easier to use the equipment.  
ꢀ
CS 5 User Manual  
- 4 -  
Safety and Environment  
Safety Instructions  
1. Do not spill any liquids on the equipment and do not drop any objects through the ventilation slots in the equip-  
ment.  
2. Use the equipment in dry rooms only. Do not expose the equipment to rain or splash water. Never place objects  
containing liquids (e.g., vases) on or near the equipment.  
3. There are no user-serviceable parts inside the equipment. Do not attempt to service the equipment yourself. Refer  
all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturer’s warranty.  
4. Before connecting the equipment to power, check that the AC mains voltage stated on the power supply included  
with the equipment is identical to the AC mains voltage available where you will use the equipment. Also check that  
the power outlet is a standard type with a protective ground connection. Disconnecting the protective ground lead  
or using non-standard power plugs or non-standard power outlets is illegal.  
5. Operate the equipment with the power supply included with the equipment only. Using a different power supply may  
cause serious damage to the unit.  
6. If any solid object or liquid penetrates into the equipment, shut down the system immediately. Disconnect the  
equipment from power immediately and have the equipment checked by AKG service personnel.  
7. If you will not use the equipment for a long period of time, disconnect the equipment from power. Please note that  
the equipment will not be fully isolated from power when you set the power switch to OFF.  
8. Disconnect the equipment from power during storms to prevent damage.  
9. Make sure to route power supply cords so that they are not likely to be walked on or pinched by items placed upon  
or against them, paying particular attention to cords at plugs, convenience receptacles, and the points where they  
exit from the equipment.  
10. To avoid hum or interference, route all audio lines, particularly those connected to microphone inputs, away from  
power lines of any type. If you use cable ducts, be sure to use separate ducts for the audio lines.  
11. Make sure to replace each built-in fuse with a standard fuse of the same type and rating only. Using any other type  
of fuse may cause excessive heating and/or a risk of fire.  
12. Never switch more than twenty micorphone stations on simultaneously because the resulting current drain may  
cause a risk of fire.  
13. Do not place the equipment near heat sources such as radiators, heating ducts, or amplifiers, etc. and do not ex-  
pose it to direct sunlight, excessive dust, moisture, rain, mechanical vibrations, or shock.  
14. Clean the equipment with a moistened (not wet) cloth only. Be sure to disconnect the equipment from power be-  
fore cleaning the equipment! Never use caustic or scouring cleaners or cleaning agents containing alcohol or sol-  
vents since these may damage the enamel and plastic parts.  
15. Use the equipment for the applications described in this manual only. AKG cannot accept any liability for damage  
resulting from improper handling or misuse.  
16. Any changes or modifications to the equipment not expressly approved by the manufacturer may void the user's  
authority to operate the equipment.  
Environment  
1. When scrapping the equipment, separate the case, circuit boards, and cables, and dispose of all components in  
accordance with local waste disposal rules.  
2. The packaging of the equipment is recyclable. Dispose of the packaging in an appropriate container provided by  
the local waste collection/recycling entity and observe all local legislation relating to waste disposal and recycling.  
FCC Statement  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device  
may not cause harmful interference, and (2) this device must accept any interference received, including interference that  
may cause undesired operation.  
CS 5 User Manual  
- 5 -  
Section 1: General  
The CS 5 is a fully modular, highly flexible conference system. Using Ethernet technology, it provides maximum secu-  
rity and excellent digital audio quality. The CS 5 components can be used for any conference system from simple se-  
tups to the most complex systems including ID card identification; three-way voting or five-way polling; interpretation  
of up to 63 languages; and infrared transmission of up to seven languages. The CS 5 is extremely easy to wire, pro-  
gram, set up, and expand.  
All microphone stations are connected to the CS5 BU Base Stration in a closed-circuit Ethernet configuration so even  
if one component fails, all other microphone stations will remain functional. The Base Unit also provides all the circuitry  
required to drive the CS5 IRT1 and CS5 IRT2 infrared radiators. The CS5 IRR7 infrared receivers provide seven selec-  
table language channels. In addition, the CS5 BU contains interfaces for a range of external devices including mixers,  
wireless microphone systems, recording devices, CD players, etc.  
The system provides 64 audio channels (0 - 63) that can be assigned as required to delegate, chairperson, or inter-  
preter stations. Channel 0 is permanently assigned as the floor channel (sum of all microphone stations, external mi-  
crophones (unless routed otherwise) and line inputs). Channels 0-6 are routed to the infrared outputs. Channels 0-3  
are available at the headphone outputs on the CS5 DU microphone station. Channels 0-63 are available at the head-  
phone outputs on the CS5 VU microphone station.  
Important:  
•
To avoid malfunctioning due to conflicting signals, use only a single CS5 BU Base Unit in any CS5 con-  
ference system.  
!
•
To avoid data loss or corruption, malfunctioning, or damage to the system, never make any changes  
to the wiring or operate any control on any system component, or disconnect the system from power  
while a software update is in progress.  
Note:  
•
For instructions on setting up your CS 5 Conference System from wiring to powering up, refer to the "Getting  
ꢀ
Started Quickly" guide that you should have received together with your shipment. If the "Getting Started Quickly"  
guide or any other component is missing, contact your AKG Distributor immediately.  
•
This User Manual contains detailed information on how to set up each CS 5 component.  
CS 5 User Manual  
- 6 -  
Section 2: Notes on Wiring and System Examples  
2.1 Notes on Wiring and System Configuration  
Important:  
1. Never connect your CS5 MK.. LAN cables to any equipment (desktop or notebook computers, etc.) other  
!
than CS 5 system components. The LAN cables will carry a 48 V supply voltage that may damage equip-  
ment not designed for such voltages.  
2. Make all audio and LAN cable connections before connecting any Conference System component to  
power.  
3. To avoid damage to any system component, do not lay, connect, or disconnect any cables while power  
to the system is on. Always disconnect the entire system from power before making any changes to  
the wiring.  
4. To avoid interference problems, make sure that all audio cables you are going to connect to the Base  
Unit audio outputs are shorter than 10 feet (3 m).  
5. Note that the CS 5 BU Base Unit will not function with no microphone stations connected to it (no mat-  
ter what other equipment you may have connected to the Base Unit). Therefore, make sure always to  
connect at least one CS 5 VU or CS 5 DU microphone station to the Base Unit to set up a functional  
CS 5 system.  
•
•
•
Route power cables so that nobody may trip over them or step on them. A cable getting disconnected by some-  
body tripping over it may cause system malfunctioning or damage to system components.  
To avoid hum problems, do not route audio or LAN cables close to power cables.  
In permanent installations, use separate ducts for power and audio/LAN cables.  
While LAN cables may be as long as 164 feet (50 m) without degrading system performance, keep all other ca-  
bles as short as possible to keep cable attenuation to a practical minimum. Check that all audio cables connected  
to the Base Unit are shorter than 10 feet (3 m).  
•
Always connect all microphone stations in any system to the Base Unit in a closed loop. Use CS5 MK.. LAN cables  
to daisy-chain all microphone stations from one SYSTEM connector on the Base Unit back to the other SYSTEM  
connector on the Base Unit. This ensures that if one of the LAN cables breaks all microphone stations will remain  
operative.  
CS 5 User Manual  
- 7 -  
Section 2: Notes on Wiring and System Examples  
2.2 System Examples  
2.2.1 Simple Discussion System  
Example 1: Simple discussion system.  
Example 1 above shows the wiring diagram for a simple discussion system. A system of this kind may comprise any  
combination of CS 5 DU and CS 5 VU microphone stations. Since the system shown includes only six microphone sta-  
tions, a single CS 5 PS 12 power supply connected to the Base Unit is enough to power the entire system.  
CS 5 User Manual  
- 8 -  
Section 2: Notes on Wiring and System Examples  
2.2.2 Computer-controlled Discussion System  
Example 2: Larger discussion system with computer control.  
Example 2 above shows a larger discussion system with more than six microphone stations and computer control. To  
ensure stable powering even if one power supply fails, connect one CS 5 PS 12 power supply to the Base Unit, one  
CS 5 PS 12 power supply to every sixth microphone station, beginning with the seventh in line counting from the Base  
Unit, and connect the last microphone station to the second SYSTEM connector on the Base Unit.  
The computer controlling the system is connected to the USB port on the Base Unit. In order to make optimum use of  
all the functions offered by computer control, we recommend using CS 5 VU microphone stations, although computer  
control will also work with CS 5 DU stations.  
CS 5 User Manual  
- 9 -  
Section 2: Notes on Wiring and System Examples  
2.2.3 Infrared Interpretation System  
Layout  
Wiring Diagram  
Example 3: Basic layout and wiring diagram for an interpretation system for three conference languages with infrared  
signal distribution.  
The panel microphones (2 shown in the layout diagram above) are connected to a microphone mixer, which feeds the  
LINE IN input on the Base Unit. The room sound system is fed by the Base Unit LINE OUT output. The four Interpreter  
Stations in the two interpretation booths are connected in a closed loop to the two SYSTEM connectors on the Base  
Unit.  
CS 5 User Manual  
- 10 -  
Section 2: Notes on Wiring and System Examples  
2.2.4 Large Conference System with Interpretation Booths  
Layout  
Wiring Diagram  
Example 4: Large conference system layout and wiring diagram.  
Example 4 shows a large conference system with CS 5 VU microphone stations with voting and polling functions, an  
interpretation booth for one target language, and an infrared distribution system for the audience.The chairperson, pan-  
elists, and delegates can listen to the loudspeakers on the Delegate Stations or use the headphones to listen to the in-  
terpreters. Since all microphones are connected to CS 5 microphone stations, no external microphone mixer is needed.  
The audience can listen to the floor signal or interpretation on their CS 5 IRR 7 infrared receivers with channel selec-  
CS 5 User Manual  
- 11 -  
Section 2: Notes on Wiring and System Examples  
tors.The wiring diagram shows how all microphone stations including the Interpreter Stations are daisy-chained together  
in a closed loop.  
To ensure stable powering even if one power supply fails, connect one CS 5 PS 12 power supply to the Base Unit, one  
CS 5 PS 12 power supply to every sixth microphone station, beginning with the seventh in line counting from the Base  
Unit, and connect the last microphone station to the second SYSTEM connector on the Base Unit.  
CS 5 User Manual  
- 12 -  
Section 3: CS 5 BU Base Unit  
3.1 General  
The CS5 BU is the Base Unit required for any CS 5 system configuration. It synchronizes all system components and  
generates the floor audio channel. you can connect to the Base Unit up to 5,000 microphone stations (Delegate Sta-  
tions, Chairperson Stations, and Interpreter Stations); external analog audio sources; an external amplifier; an audio  
recording device; and one or more infrared radiators.  
The CS 5 BU provides the following basic control functions:  
-
-
-
-
NOM limitation: maximum number of microphones that may be open at any time, selectable from 1 to 64  
Two selectable automatic microphone activation modes  
Voting initiated from a Chairperson Station  
Driving the infrared radiator panels  
More control functions are available through computer control using the CS5 ConferControl software.  
3.2 Front Panel  
Fig. 1: CS 5 BU front panel.  
1
2
3
4
5
6
SYSTEM: Sets the level of the sum of all open microphones on the microphone stations.  
LINE: Sets the level of the rear panel LINE IN line level input.  
EXT. MIC: Sets the level of the rear panel EXT. MIC IN microphone level input.  
TAPE: Sets the level of the rear panel TAPE IN input for an external audio source.  
TELEPHONE: Sets the level of the rear panel TEL. IN input for an external telephone hybrid.  
LANG. EXT.: Sets the level of the rear panel EXT. LANG. IN input for an external hardwire or wireless microphone  
used by an interpreter working outside the interpretation booths.  
7
NOM LIMIT: Sets the maximum number of microphones (NOM) that may be open simultaneously at any time and  
the number of audio channels available for interpretation. "1/63" means one open microphone and 63 interpre-  
tation channels, "64/0" means 64 open microphones and no interpretation channel.  
SPEAKERS: Sets the level of the signal fed to the loudspeakers on the microphone stations.  
LED level meter indicating the level set by the SPEAKERS control (8). Set the SPEAKERS control (8) so that the  
red Peak LED will only flash occasionally at very loud signals.  
8
9
10 MAIN: Sets the level of the rear panel LINE OUT line-level output.  
11 LED level meter indicating the level set by the MAIN control (9). Set the MAIN control (9) so that the red Peak LED  
will only flash occasionally at very loud signals.  
12 HEADPHONE: Sets the level of the headphone output (14) to the right of the HEADPHONE control.  
13 Status LEDs: The CS 5 BU provides three status LEDS:  
POWER (green) is lit to indicate that power to the Base Unit is ON.  
REMOTE (yellow) flashes to indicate that data is being transmitted.  
NOM LIMIT (yellow) flashes to indicate a synchronization error.  
Upon powering up, the REMOTE and NOM LIMIT LEDs will flash alternately for a few seconds to indicate the sys-  
tem is synchronizing and go out as soon as synchronization is completed.  
14  
: ¼" TRS headphone jack for stereo headphones only. (Using mono headphones may damage the unit.)  
15 POWER: Switches power to the Base Unit ON ("I") or OFF ("0").  
CS 5 User Manual - 13 -  
Section 3: CS 5 BU Base Unit  
3.3 Rear Panel  
Fig. 2: CS 5 BU rear panel.  
16 Dip switches: This set of dip switches allows you to route the various inputs to either the NORMAL bus or the  
EFFECTS bus, activate or deactivate NOM limitation on the SYSTEM BUS and LINE OUT outputs, mute the EXT. LANG.  
signal. Refer to section 3.4.  
17 USB port: Enables the Base Unit to be controlled from a computer. Computer control works best with CS5 VU ad-  
vanced delegate stations. The CS5 DU may not provide all the functions that may be required for more complex  
systems.  
18 SYSTEM: These two RJ 45 connectors provide the inputs, outputs, and power voltage for the microphone stations  
connected to the Base Unit. Daisy-chain the microphone stations and connect the last station in the chain to the  
second SYSTEM connector on the Base Unit. This makes sure that if one microphone station fails, all other sta-  
tions will remain fully functional.  
19 INFRA OUT: These two coaxial connectors carry the same signal for the CS5 IRT1 or CS5 IRT2 infrared radiators.  
This signal includes the output signals from the interpretation booths (channels 1-6) and the NORMAL bus signal  
(channel 0).  
20 TAPE OUT: Unbalanced TRS mini jack carrying the NORMAL bus mono signal for recording.  
21 TAPE IN: Unbalanced TRS mini jack for connecting the output of an external recording device. The input signal is  
fed to the DIRECT/TELEPHONE bus and can be routed to the NORMAL or EFFECTS buses, too.  
22 EFFECT OUT: Balanced TRS ¼" jack for sending the EFFECTS bus signal to an external effects device, e.g. a feed-  
back eliminator.  
23 EFFECT IN: Balanced TRS ¼" jack for receiving the output signal of an external effects device. This signal is fed  
to the NORMAL bus.  
24 EXT. LANG. IN: Balanced XLR line-level input for an external microphone mixer or AKG wireless microphone re-  
ceiver providing an additional interpretation channel. The input signal can be muted or fed to language channel 1  
which is part of the infrared signal.  
25 TEL. OUT: Balanced XLR connector carrying the output signal of the DIRECT/TELEPHONE bus.  
26 TEL. IN: Balanced XLR input for the output signal of a telephone hybrid. The signal is fed to the NORMAL bus.  
27 LINE OUT: Balanced XLR connector carrying the NORMAL bus signal for the conference room sound system.  
28 LINE IN: Balanced XLR input for a line-level audio source such as a CD player or A/V equipment.  
29 EXT. MIC. IN: Balanced XLR microphone-level input with 48-V phantom power for an external hardwire or wire-  
less microphone.  
30 DC 48V / 3A IN: DC input for connecting the CS5 PS 12 power supply.  
CS 5 User Manual  
- 14 -  
Section 3: CS 5 BU Base Unit  
3.4 Setting Up the Base Unit  
Important:  
•
To avoid interference problems, make sure that all audio cables you are going to connect to the Base  
Unit audio outputs are shorter than 10 feet (3 m).  
!
3.4.1 Block Diagram  
Fig. 3: Block diagram of the CS5 BU analog section.  
CS 5 User Manual - 15 -  
Section 3: CS 5 BU Base Unit  
3.4.2 Configuring the Dip Switches  
1. Before powering up, set all front panel level controls to minimum (smallest dot) and set the rear panel dip switches  
as required. Refer to fig. 3 on page 15 and Table 1 below.  
Switch position  
Dip switch  
Function  
0
1
EFFECTS bus  
EFFECTS bus  
EFFECTS bus  
EFFECTS bus  
ON  
S1  
S2  
S3  
S4  
S5  
S6  
S7  
S8  
routes LINE IN to  
routes EXT. MIC. IN to  
NORMAL bus  
NORMAL bus  
NORMAL bus  
NORMAL bus  
OFF  
routes TAPE IN to  
routes SYSTEM BUS IN to  
switches NOM attenuation on SYSTEM BUS OUT  
switches NOM attenuation on LINE OUT  
EXT. LANG. signal  
OFF  
ON  
muted  
routed to Channel 1  
Microphone activation mode  
Floor request opens available mic channel FIFO: Floor request opens available mic  
or puts microphone on waiting list. channel or cancels earliest floor request.  
Table 1: Base Unit dip switches.  
•
Dip switches S1 to S4 route the LINE, EXT. MIC., TAPE, and SYSTEM inputs to either the NORMAL or EFFECTS bus.  
The NORMAL bus feeds the mixed input signals to the TAPE, LINE, SYSTEM, , and INFRA outputs.  
The EFFECTS bus signal is available at the EFFECT output where you can connect a feedback eliminator or other  
effects device. Connect the output of your effects device to the EFFECT IN jack on the rear panel. The processed  
signal is fed to the NORMAL bus. As long as no effects device is connected, the signal is routed to the NORMAL  
bus.  
•
•
Dip switches S5 and S6 let you activate and deactivate NOM attenuation. NOM (Number of Open Microphones) at-  
tenuation reduces the volume of the loudspeakers in a sound system depending on the number of microphones  
that are active at any time. The more microphones are open, the more the loudspeaker volume is reduced. S5 al-  
lows you to activate NOM attenuation for the loudspeakers on the microphone stations connected to SYSTEM out-  
puts. S6 lets you activate NOM attenuation on the LINE OUT signal that feed the room sound system.  
Dip switch S7 allows you to select the input signal for system channel 1. To route the assigned Interpreter Station  
output to channel 1, set S7 to "0". To route the EXT. LANG. input to channel 1, set S7 to "1". You can use the lat-  
ter configuration for a consecutive interpreter with a hardwire or wireless microphone.  
•
-
Dip switch S8 selects one of two microphone activation modes.  
With S8 in position "0", a microphone will be switched on immediately on pressing the talk button ("requesting the  
floor") if a microphone channel is available. If no microphone channel is available, the microphone requesting the  
floor will be put on the waiting list.  
-
With S8 in position "1", a microphone will be switched on immediately on pressing the talk button if a microphone  
channel is available. If no microphone channel is available, the floor request on top of the waiting list will be deleted  
and the last microphone requesting the floor will be added to the waiting list.  
3.4.3 Selecting NOM Limitation/Interpretation Channels  
•
Set NOM LIMIT (7) to the desired ratio between the maximum number of microphones that may be open at any  
time and the number of channels available for interpretation.  
If no interpretation is needed, you may set NOM LIMIT to "64/0", allowing 64 microphones to be open simultane-  
ously. To reduce the number of open microphones, set NOM LIMIT to a lower position.  
If interpretation will be provided, set NOM LIMIT for the number of interpretation channels required (e.g., "48/16"  
for any number of interpretation channels up to 16 and 48 open microphones).  
CS 5 User Manual  
- 16 -  
Section 3: CS 5 BU Base Unit  
3.4.4 Powering Up  
1. Set up all microphone stations referring to section 4 (page 18) and make all power connections.  
2. Switch power to the Base Unit ON, wait for five seconds, switch the first twenty microphone stations ON, wait for  
five seconds, switch the next twenty microphone stations ON, and so on.  
Important:  
•
To avoid overloading your power line and causing a risk of fire when powering up, make sure never to  
connect more than twenty microphone stations to a common circuit with a common power switch and  
never switch more than twenty microphone stations ON at a time.  
!
Systems with one or more CS 5 VU Microphone Stations  
Important:  
•
When powering up for the first time or after making any changes to the system configuration, it is ab-  
solutely necessary to run the “LEARNING” routine by following steps 3 through 5 below. Failing to do  
so will cause severe system malfunctioning!  
!
3. Insert the SERVICE CARD supplied with the Base Unit into the card slot on any CS 5 VU microphone station.  
4. Press soft buttons 1 and 5 simultaneously on the same microphone station into which you inserted the SERVICE  
CARD.  
5. As soon as the display reads “LEARNING SUCCEEDED”, remove the SERVICE CARD. The Base Unit has now stored  
the system configuration and will load this configuration immediately after switching power ON the next time.  
If you are not sure if the “LEARNING” routine has been run, run it again. This will cause no problem.  
Important:  
•
Mark the SERVICE CARD clearly and unmistakably and keep it in a safe place. You will need to use it  
every time you power up a newly set up mobile system for the first time and every time you made any  
change to an existing (mobile or permanently installed) system configuration.  
!
Note:  
If you lose your SERVICE CARD, order a replacement from your AKG Distributor.  
•
ꢀ
Alternatively, you can program your own SERVICE CARD by changing the number of an existing chip card to “0”.  
Refer to the Software Manual for information on how to program chip card numers.  
Systems with CS 5 DU Microphone Stations only  
System configurations with CS 5 DU stations only cannot be stored in memory. To power up such a system, sim-  
ply follow steps 1 and 2 above.  
•
3.4.5 Setting Levels  
1. Set up all microphone stations referring to section 4, make all power connections and switch power to the Base  
Unit and all ancillary equipment ON. (Steps 5 through 9 in the Getting Started Quickly manual.)  
2. Have people talk into the microphones on the microphone stations. You can set the SYSTEM control to maximum  
without risking to overload the amplifier input.  
3. You can set the level controls (INPUTS ADJUST) for all other inputs you will use to maximum without risking to over-  
load the amplifier input.  
4. Set the level controls for all unused inputs to minimum.  
5. Use the SPEAKERS control (8) to set the volume level for the loudspeakers on the microphone stations just high  
enough to get optimum intelligibility. Do not set SPEAKERS higher than to the point where the red Peak LED of the  
bargraph (9) will only flicker occasionally. Excessive levels may cause audible distortion.  
6. Use the MAIN control (10) to set the volume level for the room sound system just high enough to get optimum in-  
telligibility and avoid feedback. Do not set MAIN higher than to the point where the red Peak LED of the bargraph  
(11) will only flicker occasionally. Excessive levels may cause audible distortion.  
7. Connect a pair of headphones to the jack on the front panel for monitoring the main mix on the NORMAL bus.  
CS 5 User Manual  
- 17 -  
Section 3: CS 5 BU Base Unit  
The jack accepts all standard stereo headphones with a ¼" TRS jack plug.  
Set the HEADPHONE control (12) just high enough so you can comfortably monitor the main mix.  
•
Important:  
•
Excessive headphone listening levels my damage your hearing. So use the HEADPHONE control with  
care.  
!
3.4.6 Selecting NOM Limitation/Interpretation Channels  
•
Set NOM LIMIT (7) to the desired ratio between the maximum number of microphones that may be open at any  
time and the number of channels available for interpretation.  
If no interpretation is needed, you may set NOM LIMIT to "64/0", allowing 64 microphones to be open simultane-  
ously. To reduce the number of open microphones, set NOM LIMIT to a lower position.  
If interpretation will be provided, set NOM LIMIT for the number of interpretation channels required (e.g., "48/16"  
for any number of interpretation channels up to 16 and 48 open microphones).  
CS 5 User Manual  
- 18 -  
Section 4: CS 5 DU Delegate Station  
4.1 Introduction  
The CS5 DU is the basic microphone station for the CS 5 conference system. It provides a microphone connection with  
talk button, two built-in loudspeakers, and two headphone jacks.  
The loudspeakers reproduce the main mix ("floor signal") while the headphone jacks allow the user to listen to the floor  
signal or one of three interpreted languages.  
4.2 Controls, Inputs, and Outputs  
Fig. 4: Controls, inputs, and outputs on the CS5 DU.  
1
2
: Mini jack for stereo headphones.  
Microphone input for connecting any of the gooseneck microphones listed in section 2.  
3-4 Volume control buttons: The UP button (4) increases and the DOWN button (3) decreases the volume of the built-  
in speakers or headphones connected to the microphone station.  
• If no headphones are connected to the microphone station, the volume control buttons set the volume of the  
built-in loudspeakers.  
• If a single pair of headphones is connected to either headphone jack, the volume control buttons set the vol-  
ume for that pair of headphones.  
• If headphones are connected to both headphone jacks, the volume control buttons set the volume of both head-  
phone channels.  
Note: When the microphone is open, the volume of the loudspeakers will be attenuated by a specific amount de-  
pending on the polar pattern of the microphone used. The headphones volume will not be affected.  
ꢀ
CS 5 User Manual  
- 19 -  
Section 4: CS 5 DU Delegate Station  
Refer to  
fig. 4  
on page 18.  
5
Talk button: Pressing the talk button once activates the microphone. The status LED above the button will be lit.  
Pressing the talk button again switches the microphone off. The status LED above the button will go out.  
If no microphone channel is available, the microphone will not be activated before a channel becomes available.  
The status LED will be flashing. Pressing the talk button again cancels the floor request and the status LED will go  
out. The talk button also allows simple two-way (aye/no) voting (refer to section 5.4.2).  
Loudspeakers.  
6
7
8
DC input for connecting a CS5 PS 12 power supply.  
System port: RJ45 connector for CS5 MK.. LAN cables. (Refer to section 2.2 for example wiring diagrams.)  
4.3 Setting Up  
4.3.1 Making Connections  
1. Screw the microphone capsule on the gooseneck.  
2. Screw the gooseneck into the microphone input (2).  
Fig. 4, p. 18. 3. Use the appropriate CS5 MK.. cables to connect the system ports on the microphone station to the system ports  
on the preceding and subsequent microphone stations.  
4.3.2 Selecting Operating Modes  
Important:  
•
To avoid malfunctioning, do not change any dip switch settings on the Base Unit or any microphone sta-  
tion while power to the system is ON!  
!
Table 2: CS 5 DU dip switches.  
Dip switches  
Function  
Switch positions  
Microphone model  
S1, S2  
Match microphone station audio input  
to microphone output signal.  
Dip switch  
S1  
0
S2  
0
CK 31 cardioid microphone  
0
1
1
1
CK 33 hypercardioid microphone  
CK 47, CK 80 shotgun microphones  
S3  
Unused  
0
1
S4  
Microphone muting on priority request:  
Microphone can be muted.  
Microphone will not be muted.  
S5, S6  
Switch left-hand phones output to channel  
(language selection):  
Channel  
Floor  
S5  
0
S6  
0
CH 1 or EXT. LANG.  
CH 2  
1
0
0
1
CH 3  
1
1
S7, S8  
Switch right-hand phones output to channel  
(language selection):  
Channel  
Floor  
S7  
0
S8  
0
CH 1 or EXT. LANG.  
CH 2  
1
0
0
1
CH 3  
1
1
1. Referring to Table 2 above, set S1 and S2 for the microphone capsule you are going to connect to the microphone  
station.  
The settings of S1-S2 determine the frequency response and gain of the audio section as well as the amount of  
gain reduction that is applied to the loudspeaker amplifier as soon as the microphone opens.Therefore, microphone  
stations with unidirectional microphone capsules allow delegates to hear other talkers on the built-in loudspeak-  
ers even while the microphone is open.  
CS 5 User Manual  
- 20 -  
Section 4: CS 5 DU Delegate Station  
Important:  
•
The amount of gain reduction applied to a cardioid capsule is rather low while hypercardioid and shot-  
gun microphones will be attenuated more significantly. To avoid feedback problems, make sure to set  
S1-S2 to the correct positions as per Table 2 on page 19.  
!
2. Set the other dip switches to select the microphone priority/muting mode and select the input signals for the left  
and right-hand headphone outputs.  
CS 5 User Manual  
- 21 -  
Section 5: CS5 VU Voting/Chairperson Station  
5.1 Introduction  
The CS5 VU can be configured either as a delegate station with a voting function or as a chairperson station with vot-  
ing and priority functions. Like the CS5 DU, it provides a microphone connection, talk button, two built-in loudspeak-  
ers, and two headphone jacks.  
The loudspeakers reproduce the main mix ("floor signal") while the headphone jacks allow the user to listen to the floor  
signal or one of 63 interpreted languages.  
In addition, the CS 5 VU incorporates a chip card reader for user identification by conference control software. A liquid-  
crystal display and five soft buttons allow the user to call the meeting to order, initiate ballots, cast their vote, select lan-  
guages for the headphone outputs, etc.  
5.2 Control Panel, Inputs, and Outputs  
Fig. 5: CS5 VU control panel, inputs and outputs.  
1
2
Loudspeakers.  
Microphone input for connecting any of the gooseneck microphones listed in section 2.  
Note: When the microphone is open, the volume of the loudspeakers will be attenuated by a specific amount de-  
pending on the polar pattern of the microphone used. The headphones volume will not be affected.  
ꢀ
3
4
Chip card slot  
Talk button: Basically, pressing the talk button once activates the microphone. The status LED above the button  
will be lit. Pressing the talk button again switches the microphone off. The status LED above the button will go out.  
CS 5 User Manual  
- 22 -  
Section 5: CS5 VU Voting/Chairperson Station  
Refer to  
fig. 5  
on page 21.  
5
6
: Mini jack for stereo headphones.  
Soft buttons: These buttons control the functions assigned to them in the various menus shown on the display.  
The buttons are assigned to numbers 1 through 5 in the lower display line from left to right.  
DC input for connecting a CS5 PS 12 power supply.  
System port: RJ45 connector for CS5 MK.. LAN cables. (Refer to section 2.2 for example wiring diagrams.)  
Display: Two-line liquid-crystal display indicating the main menu for selecting functions and the submenus for set-  
ting the parameters for each function.  
7
8
9
CS 5 User Manual  
- 23 -  
Section 5: CS5 VU Voting/Chairperson Station  
5.3 Setting Up  
5.3.1 Making Connections  
1. Screw the microphone capsule on the gooseneck.  
2. Screw the gooseneck into the microphone input (2).  
Fig. 5, p. 21.  
3. Use the appropriate CS5 MK.. cables to connect the system ports on the microphone station to the system ports  
on the preceding and subsequent microphone stations.  
5.3.2 Selecting Operating Modes  
Important:  
•
To avoid malfunctioning, do not change any dip switch settings on the Base Unit or any microphone sta-  
tion while power to the system is ON!  
!
Dip switches  
S1, S2  
Function  
Switch positions  
Microphone model  
Match microphone station audio input  
to microphone output signal.  
Dip switch  
S1  
0
S2  
0
CK 31 cardioid microphone  
0
1
1
1
CK 33 hypercardioid microphone  
CK 47, CK 80 shotgun microphones  
S3  
Unused  
0
1
S4  
S5  
Microphone muting on priority request:  
Test mode:  
Microphone can be muted.  
Microphone will not be muted.  
Normal operating mode  
as selected on S8  
Test mode: Display indicates  
data communication status.  
S6  
S7  
S8  
Configuration:  
Last user-selected configuration  
Enabled  
Factory default configuration  
Disabled  
Voting from delegate station:  
Voting Station operating mode:  
DELEGATE  
PRESIDENT  
Table 3: CS 5 VU dip switches.  
1. Referring to Table 3 above, set S1 and S2 for the microphone capsule you are going to connect to the microphone  
station.  
The settings of S1-S2 determine the gain of the audio section as well as the amount of gain reduction that is ap-  
plied to the loudspeaker amplifier as soon as the microphone opens. Therefore, microphone stations with unidi-  
rectional microphone capsules allow delegates to hear other talkers on the built-in loudspeakers even while the  
microphone is open.  
Important:  
•
To avoid feedback problems, make sure to set S1 and S2 to the correct positions as per Table 3  
above.  
!
2. Set the other dip switches to select the microphone priority/muting mode and select the input signals for the left  
and right-hand headphone outputs.  
CS 5 User Manual  
- 24 -  
Section 5: CS5 VU Voting/Chairperson Station  
5.3.3 DELEGATE Mode  
If you have set dip switch S8 for DELEGATE mode, the Delegate main menu will appear on the display upon powering  
up.  
Fig. 6: Delegate menu and selectable submenus.  
1. Press soft button 1 to select the volume control for the left-hand headphone output. Press soft buttons 2 and 4 to  
decrease (-) or increase (+) the volume. A bargraph indicates the current setting.  
Press soft button 3 (BACK) to return to the main menu.  
2. Press soft button 2 to call up the language selection submenu for the left-hand headphone output. Press soft but-  
tons 2 and 4 to select the desired language. Channel 0 carries the floor signal, channels 1-63 are assigned to the  
interpreted languages listed in Table 4 in section 6.3.5 on page 32.  
Press soft button 3 (BACK) to return to the main menu.  
3. Press soft button 3 to select the loudspeaker volume control.  
4. Press soft buttons 2 and 4 to decrease (2) or increase (4) the volume. A bargraph indicates the current setting.  
Press soft button 3 (BACK) to return to the main menu.  
5. Press soft button 4 to call up the language selection submenu for the right-hand headphone output. Press soft but-  
tons 2 and 4 to select the desired language. Channel 0 carries the floor signal, channels 1-63 are assigned to the  
interpreted languages listed in Table 4 in section 6.3.5 on page 32.  
Press soft button 3 (BACK) to return to the main menu.  
6. Press soft button 5 to select the volume control for the right-hand headphone output. Press soft buttons 2 and 4  
to decrease (2) or increase (4) the volume. A bargraph indicates the current setting.  
Press soft button 3 (BACK) to return to the main menu.  
CS 5 User Manual  
- 25 -  
Section 5: CS5 VU Voting/Chairperson Station  
5.3.4 PRESIDENT Mode  
If you have set dip switch S8 for PRESIDENT mode, the President main menu will appear on the display upon power-  
ing up.  
Fig. 7: President menu and selectable submenus.  
1. Press soft button 1 to select the volume control for the left and right-hand headphone outputs. Press soft buttons  
1 and 2 to decrease (-) or increase (+) the volume for the left-hand headphones, buttons 4 and 5 to decrease (-)  
or increase (+) the volume for the right-hand headphones. Two bargraphs indicate the current settings.  
Press soft button 3 (BACK) to return to the main menu.  
2. Press soft button 2 to call up the language selection submenu for the left and right-hand headphone outputs.  
Press soft buttons 1 and 2 to select the desired language for the left-hand headphones, buttons 4 and 5 to select  
the desired language for the right-hand headphones. Channel 0 carries the floor signal, channels 1-63 are assigned  
to the interpreted languages listed in Table 4 in section 6.3.5 on page 32.  
Press soft button 3 (BACK) to return to the main menu.  
3. Press soft button 4 to select the loudspeaker volume control.  
Press soft buttons 2 and 4 to decrease (-) or increase (+) the volume. A bargraph indicates the current setting.  
Press soft button 3 (BACK) to return to the main menu.  
4. Press soft button 3 to set the microphone station to priority mode. In priority mode, pressing the talk button once  
always activates the microphone and mutes the microphones on all microphone stations where priority muting has  
been enabled.  
To quit priority mode and return to the main menu, press soft button 4 (CLEAR).  
5. Press soft button 5 to initiate a ballot or opinion poll. Refer to section 5.4 below.  
6. To return to the main menu, press soft button 3 (BACK).  
CS 5 User Manual  
- 26 -  
Section 5: CS5 VU Voting/Chairperson Station  
5.4 Voting/Polling  
Important:  
•
If anything goes wrong while a ballot or poll is in progress, the display will go dark (in case of a power  
failure) or show "VOTING FAILED". Voting/polling data may be lost or corrupted.  
To ensure correct results, always repeat the entire ballot or poll once the problem has been corrected.  
!
•
5.4.1 Controlling a Ballot or Opinion Poll (PRESIDENT Mode)  
•
Instruct the president of the meeting how to control a complete voting or polling procedure:  
1. From the President main menu, press soft button 5 (VOTE) to call up the voting control menu:  
2a. To start a three-way (no/abstention/aye) ballot, press soft button 1. The display will change like this:  
The delegates may now cast their votes.  
As long as "TIME LEFT" is shown on the display, you can press soft button 5 (ABORT) to stop the procedure and  
return to the voting control menu.  
2b. To start an opinion poll (five options), press soft button 2. The display will change like this:  
2c. To start a two-way (aye/no) vote, press soft button 5. This allows two-way voting from both CS 5 VU and CS 5 DU  
microphone stations.  
The delegates may now cast their votes. Refer to section 5.4.2 on page 27.  
As long as "TIME LEFT" is shown on the display, you can press soft button 5 (ABORT) to stop the procedure and  
return to the voting control menu.  
3. The delegates may now cast their votes.  
As long as "TIME LEFT" is shown on the display, you can press soft buttons 1 and 5 (ABORT) simultaneously to  
stop the procedure and return to the voting control menu.  
4. As soon as all delegates have pressed their voting buttons, the votes are counted automatically and this screen  
appears on the display (results shown below are examples):  
5. When the counting is done, the display will change like this…  
CS 5 User Manual  
- 27 -  
Section 5: CS5 VU Voting/Chairperson Station  
… or like this…  
… to show the votes have been counted. The top line on each CS 5 VU microphone station indicates the results.  
6. Press any button to return to the President main menu.  
5.4.2 Voting in DELEGATE Mode  
•
Instruct the delegates how to cast their votes:  
1. When the president starts a ballot or opinion poll, the display on each delegate station registered for voting changes  
like this…  
… for three-way voting, or like this…  
… for an opinion poll.  
2a. Press the appropriate soft button to cast your vote.  
2b. Simple aye/no voting dan be done from both CS 5 VU and CS 5 DU microphone stations:  
- To vote “aye”, press the talk button when the chairperson asks you to do so.  
- To vote “no”, ignore the chairperson’s request and do not press any button until the voting time has elapsed.  
3. As soon as all delegates have pressed their voting buttons, the votes are counted automatically and this screen  
appears on the display:  
4. When the counting is done, the display will change like this…  
… or like this…  
… to show the votes have been counted.  
5. Press any soft button to return to the Delegate main menu.  
CS 5 User Manual  
- 28 -  
Section 5: CS5 VU Voting/Chairperson Station  
5.5 Chip Card Identification  
Chip card identification is only available in a computer controlled system and the identification system only accepts AKG  
chip cards. The chip card reader and control software check the identity of the person using the microphone station as  
well as their priority and voting rights, allowing votes to be weighted or classified. This system also allows holders of  
AKG chip cards to exercise their rights not only from their assigned microphone stations, but from any CS 5 VU micro-  
phone station in the conference system.  
Note: To assign chip cards to persons, enter each person's data into the database in the CS 5 ConferControl soft-  
ware. For details, refer to the ConferControl Operating Manual.  
ꢀ
• Instruct users how to identify themselves to the system:  
1. Insert the chip card into the chip card reader slot with the contacts pointing toward the slot as shown on the dis-  
play:  
The main menu appears on the display.  
If you inserted the card the wrong way, or if you inserted an incompatible card, a warning message ("WRONG  
CARD") will appear on the display:  
Important:  
•
Inserting any card other than an AKG chip card causes malfunctioning and may even damage the card  
or the equipment.  
!
2. Remove the chip card by the time the session is over.  
Note: If two persons share a single CS5 VU, both persons can vote by taking turns using their chip cards and pro-  
ceeding as describe in sections 5.4 and 5.5 above.  
ꢀ
CS 5 User Manual  
- 29 -  
Section 6: CS 5 IU Interpreter Station  
6.1 Introduction  
The CS 5 IU adds interpretation capabilities to the CS 5 conference system. It provides inputs and outputs for a goose-  
neck microphone and headphones or a headset, a built-in loudspeaker, source and target language selectors, a mi-  
crophone switch, cough button, "slow" signal button, and a signal button for requesting a technician's assistance.  
6.2 Control Panel, Inputs, and Outputs  
Fig. 8: CS 5 IU control panel, inputs, and outputs.  
INPUT SELECT: These four keys select the source language signal that is routed to the headphone output.  
1 FLOOR: Selects the floor (main mix) signal.  
2 A: Selects the next item from a list.  
3 B: Selects the previous item from a list.  
4 RELAY: Selects the relay-language channel specified by the organizer or chief interpreter.  
5 Backlit LC display.  
6 BASS: Cuts/boosts the low-frequency range of the headphone or loudspeaker signal.  
7 TREBLE: Cuts/boosts the high-frequency range of the headphone or loudspeaker signal.  
8 VOLUME: Sets the volume level of the headphone or loudspeaker signal.  
9 Microphone status LED: Indicates the current operating status of the microphone:  
• Lit: microphone is open (MICROPHONE switch (14) set to "ON").  
• Dark: microphone is off or muted (MICROPHONE switch (14) set to "OFF" or "MUTE").  
CS 5 User Manual  
- 30 -  
Section 6: CS 5 IU Interpreter Station  
Refer to  
fig. 8  
on page 29.  
10 Loudspeaker: The loudspeaker is automatically muted when a pair of headphones is connected to the headphone  
output (18).  
When no headphones are connected to the Interpreter Station, the loudspeaker reproduces the selected incoming  
signal. The rotary controls (6), (7), and (8) adjust the loudspeaker signal.  
OUTPUT SELECT: These keys select one of two pre-selected target language channels and allow the interpreter to re-  
quest the talker to speak more slowly or to call a technician for assistance (provided a technician is available).  
11 A: Routes the microphone signal to the target-language channel specified for this booth.  
12 CALL: This key has two functions:  
• Pressing <CALL> momentarily sends a "speak slowly" signal to the talker. The red LED above the <CALL>  
key and the green LED on the microphone arm of the talker's Delegate Station will flash for about 5 seconds.  
The display (5) shows the message "SENDING SLOWLY PLEASE". Pressing <CALL> momentarily again before  
the five seconds have elapsed will stop the signal.  
• Holding down <CALL> for at least 3 seconds activates an appropriate message on the computer monitor  
alerting the technician that an interpreter needs assistance. To cancel the signal, hold down <CALL> again for  
about 3 seconds.  
13 B: Routes the microphone signal to the source-language channel specified for this booth.  
14 MICROPHONE: This toggle switch provides three positions:  
• OFF: The microphone is off and the LED on the microphone arm is dark.  
• ON: The microphone is open and the LED on the microphone arm is lit.  
• MUTE (cough button function): The microphone is muted and the LED on the microphone arm is dark for as  
long as you hold the switch in the MUTE position. The switch will return to the ON (center) position as soon as  
you release the switch.  
15 Microphone input.  
16 External microphone input: This mini jack allows you to connect the microphone of a headset if the client spec-  
ifies headsets for the interpreters instead of microphone arms and separate headphones.  
17 System port: RJ45 connector for CS5 MK.. LAN cables. (Refer to section 2.2 for example wiring diagrams.)  
18  
: Mini jack for stereo headphones.  
6.3 Setting Up  
Important:  
•
According to international practice as specified by the AIIC, each interpretation booth must provide  
two Interpreter Stations because interpreters never work alone. Having an interpreter work alone in a  
booth would be unethical.  
!
Note: In the following sections, the terms "source language", "target language", and "relay language" will be used  
frequently.  
ꢀ
The source language is the language an interpreter translates into another language. That other language is  
called the target language.  
A relay language is a target language that is used as a source language by another interpreter if that inter-  
preter is not qualified to interpret the original source language.  
6.3.1 Making Connections  
1. Screw the microphone capsule on the gooseneck.  
2. Screw the gooseneck into the microphone input.  
3. Use the appropriate CS5 MK.. cables to connect the system ports on the microphone station to the system ports  
on the preceding and subsequent microphone stations.  
CS 5 User Manual  
- 31 -  
Section 6: CS 5 IU Interpreter Station  
6.3.2 Selecting Station Addresses  
1. Set the MICROPHONE switch to "OFF" to switch the microphone off.  
2. Press <FLOOR> + <CALL> + <RELAY> simultaneously to enter service mode. The display changes like this:  
SERVICE MENU  
EXIT WITHOUT SAVING  
———————  
<<PREV  
|
|
NEXT>>  
3. Select <NEXT> (press <RELAY>) to bring up this screen:  
SERVICE MENU  
SINGLE MODE  
<<PREV  
< OFF >  
NEXT>>  
4. Press <INPUT/A> or <INPUT/B> to call up the lowest possible address for the Interpreter Station (e.g., “002”):  
SERVICE MENU  
SINGLE MODE  
<<PREV  
< 002 >  
NEXT>>  
5. Press <INPUT/A> to select the next higher address or <INPUT/B> to select the next lower address.  
Important:  
•
Be sure to assign a unique address to each Interpreter Station. Use consecutive numbers starting with  
"1". Assigning the same address to more than one Interpreter Station would cause system malfunc-  
tioning.  
!
Assign one odd and one even number to the Interpreter Stations in each booth, starting with "1", for instance,  
1-2 (booth no. 1), 3-4 (booth no. 2), 5-6 (booth no. 3), etc. Make sure that the odd number is lower than the even  
number in each booth.  
6. Select target language channels: refer to section 6.3.3 below.  
7. Repeat steps 1-4 above for each Interpreter Station.  
8. To leave service mode and return to normal mode, press <FLOOR> + <CALL> + <RELAY> again.  
6.3.3 Selecting Target Language Channels  
•
On your list of language pairs, assign one audio channel to each target language (e.g., channel 1 -> English, chan-  
nel 2 -> French, etc.).  
•
Assign each of these channel numbers to one interpretation booth (e.g. booth no. 1 -> English, booth no. 2 ->  
French, etc.).  
If a relay language has been specified, assign a channel number to the relay language. Invariably, the relay lan-  
guage will be identical to one of the target languages.  
Route output A on each Interpreter Station in the same booth to the same language channel (e.g., select channel  
1 (English) for output A on each Interpreter Station in booth 1, channel 2 (French) for output A on each Interpreter  
Station in booth 2, etc.)  
Route output B on each Interpreter Station in each booth to the language channel number assigned to the relay  
language (e.g., channel 3 for Italian).  
•
•
To select output channels,  
1. In service mode, press <RELAY) and <FLOOR> to call up this screen:  
SERVICE MENU  
OUTPUT ‘A’ CHANNEL  
<<PREV  
< 002 >  
NEXT>>  
CS 5 User Manual  
- 32 -  
Section 6: CS 5 IU Interpreter Station  
Note: If you have quit service mode, switch the microphone off and press <FLOOR> + <CALL> + <RELAY> si-  
multaneously to enter service mode, then use <RELAY> and <FLOOR> to call up the above screen.  
ꢀ
2. Press <INPUT/A> to increase the channel number and <INPUT/B> to decrease the channel number.  
3. Press <RELAY> to select the name of the language ("OUTPUT ‘A’ MNEMONIC") you assigned to the channel num-  
ber you just selected. Refer to section 6.3.5 for a list of languages and their abbreviations available on the  
CS 5 IU.  
4. Press <RELAY> to call up the language selection menu for output B ("OUTPUT ‘B’ CHANNEL").  
5. Press <INPUT/A> and <INPUT/B> to select the channel number you assigned to the relay language.  
6. Press <RELAY> to select the name of the language ("OUTPUT ‘B’ MNEMONIC") you assigned to the relay chan-  
nel. Refer to section 6.3.5 for a list of languages and their abbreviations available on the CS 5 IU.  
7. Repeat steps 1-7 above for each pair of Interpreter Stations.  
6.3.4 List of Available Language Names  
Abbreviation  
ALB  
Language  
ALBANIAN  
ARABIC  
Abbreviation  
GEO  
GER  
GRE  
HEB  
Language  
GEORGIAN  
GERMAN  
Abbreviation  
POL  
Language  
POLISH  
ARA  
POR  
PORTUGUESE  
ROMANIAN  
RUSSIAN  
ARC  
ARM  
AZE  
ARAMAIC  
ARMENIAN  
AZERBAIJANI  
BULGARIAN  
CHINESE  
CROATIAN  
CZECH  
GREEK  
RUM  
RUS  
HEBREW  
HUN  
ISL  
HUNGARIAN  
ICELANDIC  
IRISH  
SER  
SERBIAN  
BUL  
SLO  
SLOVAK  
CHI  
GAI  
SLV  
SLOVENIAN  
SPANISH  
CRO  
CES  
ITA  
ITALIAN  
SPA  
JPN  
JAPANESE  
KURDISH  
SUX  
SUMERIAN  
SWEDISH  
TIBETAN  
DAN  
DUT  
DANISH  
KUR  
LAV  
SWE  
TIB  
DUTCH  
LATVIAN  
ENG  
EST  
ENGLISH  
ESTONIAN  
FINNISH  
LIT  
LITHUANIAN  
MACEDONIAN  
MALTESE  
NORWEGIAN  
TUR  
TURKISH  
MAC  
MLT  
NOR  
UKR  
UKRAINIAN  
FIN  
FRA  
FRENCH  
Table 4: Available language names and abbreviations.  
6.3.5 Selecting the Microphone Type  
1. In service mode, press <RELAY> to call up this screen:  
SERVICE MENU  
MICROPHONE TYPE  
<<PREV  
<CK 31>  
NEXT>>  
2. Use <INPUT/A> and <INPUT/B> to selct the micorphone type you connected to the Interpreter Station mic arm.  
3. Press <RELAY> to call up the “SAVE CONFIGURATION” screen.  
4. To save your settings, switch the microphone OFF and press <INPUT/A> and <INPUT/B> simultaneously.  
5. To return to normal mode (main menu), press <FLOOR> + <CALL> + <RELAY> simultaneously.  
Note: You cannot leave the service menu before having saved your settings in the “SAVE CONFIGURATION” screen.  
ꢀ
CS 5 User Manual  
- 33 -  
Section 6: CS 5 IU Interpreter Station  
6.4 Using the Interpreter Station  
Important:  
•
Before powering the system up, set the MICROPHONE switch on each Interpreter Station to "OFF" to  
avoid "broadcasting" any unofficial conversations.  
!
Upon system power-up,  
•
the display shows the message "SYSTEM STARTING…" until synchronization is completed. Once synchronization  
is finished, the display shows the main menu.  
•
the microphone input is automatically routed to output A and the red LED above OUTPUT SELECT key <A> is lit.  
The microphone will be open only if the MICROPHONE switch is in its center position ("ON"). When the micro-  
phone is open, the red LED on the microphone arm will be lit.  
•
if the MICROPHONE switches on both Interpreter Stations are in their "ON" positions, the microphone on the In-  
terpreter Station with the lower (odd) address will be opened. The microphone on the Interpreter Station with the  
higher (even) address will be muted. On the active Interpreter Station, the red LED above the active OUTPUT SE-  
LECT key and the red LED on the microphone arm will be lit, while the corresponding LEDs on the other Interpreter  
Station will remain dark.  
Instruct the interpreters how to use the Interpreter Stations:  
1. Select your source language:  
• If the person using the floor microphone speaks your source language, press <FLOOR>. You will hear the floor  
talker on your headphones and the display shows the message "FLOOR".  
• If you need your colleagues' relay, press <RELAY>. On your headphones, you will hear the voice of the inter-  
preter working into the relay language. The display shows the message "RELAY".  
The microphone signal will be automatically routed to output A.  
• To select one of the other available source languages, press <INPUT/A> or <INPUT/B>. You will hear the se-  
lected language on your headphones and the display indicates the selected language".  
2. Use the VOLUME, BASS, and TREBLE controls to adjust the headphone volume and sound for optimum intelligibility.  
These controls also set the volume and sound of the loudspeaker on the Interpreter Station.  
3. Select your target language:  
• To interpret from the floor language (e.g., English) into your booth's target language (e.g., Portuguese), check  
that output A is selected (the red LED above the OUTPUT SELECT <A> key is lit). If it is not, press <A>.  
• If a speaker of your booth's target language (e.g., Portuguese) takes the floor and you are required to interpret  
into the relay language (e.g., English), press <B> to select output B. The red LED above the OUTPUT SELECT  
<B> key is lit and the headphones are automatically switched to the floor channel.  
(Tech note: The floor channel is automatically fed to the language channel selected for output A to save dele-  
gates the trouble of having to switch their headphones to the floor channel.)  
Note: Pressing an OUTPUT SELECT key on one control panel will route the other control panel (which becomes a  
"slave" to the first panel) in the booth to the same output channel. The appropriate LED on the "slave" control  
panel will be lit accordingly.  
ꢀ
4. Controlling the microphones:  
• The interpreter who agreed to begin opens their microphone by setting the MICROPHONE switch to "ON" and  
the other interpreter switches their microphone OFF (unless it is off already). The red LED on the open micro-  
phone and the red LED above the active OUTPUT SELECT key are lit.  
Important:  
•
Make sure never to switch both microphones in your booth ON simultaneously. If you do, only one mi-  
crophone will be activated and the other muted automatically, so the wrong microphone may come on.  
!
• When it is time to relieve your colleague, you can do so in one of two ways:  
- Method 1: the interpreter on duty switches their microphone OFF (the red LED on the microphone goes out)  
and the other interpreter switches their microphone ON (the red LED on the microphone comes on).  
CS 5 User Manual  
- 34 -  
Section 6: CS 5 IU Interpreter Station  
- Method 2: the interpreter taking over presses the appropriate OUTPUT SELECT key. The red LED on the micro-  
phone comes on, the relieved colleague's microphone is automatically muted, and the red LED on that micro-  
phone goes dark.  
Note that when using this method, one microphone will always be open. To make sure your listeners will not hear  
any of your internal conversations, always set the MICROPHONE switches on both control panels to OFF when  
none of you is interpreting.  
5. Controlling talkers:  
• If the person delivering a speech talks too fast, press <CALL> momentarily. This causes the green LED on the  
microphone arm on the talker's Delegate Unit to flash for five seconds. The display on your control panel shows  
the message "SENDING SLOWLY PLEASE". To stop the signal before the five seconds are over, press <CALL>  
again.  
6. Calling a technician (if the system is computer controlled and a technician is available):  
• If there is a technical problem or you have run out of water, etc. hold down <CALL> for at least three seconds.  
This causes an appropriate message to appear on the computer monitor and the message "CALLING TECHNI-  
CIAN" to appear on your control panel display.To delete the messages, press and hold <CALL> again for at least  
three seconds.  
CS 5 User Manual  
- 35 -  
Section 7: Infrared Transmission System  
7.1 CS 5 IRT 1 and CS 5 IRT 2 Infrared Radiators  
7.1.1 General  
The CS 5 IRT 1 and CS 5 IRT 2 infrared radiators are capable of transmitting seven interpretation channels to the  
CS 5 IRR 7 infrared receivers. The two radiator models are technically identical, except that the CS 5 IRT 2 is larger  
than and provides about twice the radiation range of the CS 5 IRT 1.  
Each infrared radiator comes complete with a mounting bracket for installation on a wall or ceiling.  
Fig. 9: CS 5 IRT 1 and CS 5 IRT 2 front views.  
Fig. 9a: CS 5 IRT 1/CS 5 IRT 2 bottom panel.  
1
2
3
4
5
Green OPERATE LED: The green OPERATE LED is lit to indicate that signal is being radiated.  
Yellow OPERATE LED: The yellow OPERATE LED is lit to indicate that the infrared driver circuitry is in standby mode.  
MAINS: This red LED is lit to indicate that power to the radiator is ON.  
IREDs  
IN: BNC input connector for the PPM modulated time-multiplexed signal driving the IREDs (infrared emitting diodes)  
(7).  
Refer to  
fig. 9a.  
6
7
OUT: This BNC output connector is connected in parallel to the IN connector allowing you to daisy-chain several  
infrared radiators.  
Power input: Standard IEC power connector for 230 V/50 Hz.  
7.1.2 Placement  
•
Basically, it is best to place the infrared radiators as close as possible to the area where the receivers will be used  
and as high above the floor as practical. Diagram 1 in the Quickstart Manual shows an example of two infrared ra-  
diators covering the delegates' tables only.  
CS 5 User Manual  
- 36 -  
Section 7: Infrared Transmission System  
•
To cover an entire room, place one infrared radiator in each corner of the conference room, at least 10 feet (3 m)  
above the floor, aligning the front panel to face the opposite corner.  
Walls and/or ceilings that are painted a dark color, paneled, or acoustically treated will absorb more infrared radi-  
ation than white surfaces, so you will need more infrared radiators in darker rooms.  
•
Sunlight, fluorescent lighting, and photo flashes may weaken infrared radiation. Therefore, try to place the infrared  
radiators where they will not be exposed to natural or artificial light or use some extra IRTs.  
Note: Working out the exact number of infrared radiators needed for optimum room coverage and placing them cor-  
rectly can be a challenge in some rooms. As a rule of thumb, it is better to use many small (CS 5 IRT 1) radia-  
tors than only a few large ones (CS 5 IRT 2). If you need assistance, your dealer or nearest AKG Distributor will  
be glad to help.  
ꢀ
7.1.3 Mounting  
•
For mobile use, you can fix the support frame of the infrared radiator on a heavy standard loudspeaker stand.  
•
For permanent installations, you can directly screw the support frame on a wall or ceiling at any desired angle. To  
mount a radiator in a corner, you may need additional angle brackets (available from hardware stores).  
•
To set the tilt angle of the radiator, slacken the set screws on the support frame, rotate the radiator to the desired  
angle, and tighten the set screws.  
7.1.4 Connections  
Important: To avoid damage to any system components, do not lay, connect, or disconnect any cables while power to  
the system is on. Always disconnect the entire system from power before making any changes to the wiring.  
1. Use RG58 50-ohm coaxial cable and BNC connectors to connect one INFRA OUT jack on the Base Unit rear panel  
to the IN BNC jack on the infrared radiator on the left side of the room.  
2. Use a cable of the same length (or as nearly as possible) to connect the other INFRA OUT jack on the Base Unit  
rear panel to the IN BNC jack on the infrared radiator on the right side of the room.  
3. If you need to use more than one radiator on either bus, use RG58 50-ohm coaxial cable and BNC connectors to  
connect the OUT jack on the first radiator to the IN jack on the subsequent radiator, and so on.  
Note: To ensure consistent performance of the two radiators, keep the difference in length between the two cables  
to a practical minimum (less than 164 feet/50 m).  
ꢀ
4. Connect each infrared radiator to power.  
The CS 5 IRT 1 and CS 5 IRT 2 infrared radiators have no power switches. Therefore, connect the power input on  
each radiator to a switched 230 V/50 Hz power outlet protected by an appropriate fuse.  
Important:  
•
If no switched power outlets are available at the site of a permanent installation, ask a qualified elec-  
trician to install the required number of outlets in the conference room and a suitable ON/OFF switch  
in the control room in accordance with local electrical and occupational safety regulations.  
!
CS 5 User Manual  
- 37 -  
Section 7: Infrared Transmission System  
7.2 CS 5 IRR 7 Infrared Receiver  
7.2.1 General  
The CS 5 IRR 7 is a light, portable infrared receiver for use with the CS 5 IRT 1 and CS 5 IRT 2 infrared radiators. It  
provides seven selectable audio channels, a mini-jack headphone output, volume control, and ON key. The receiver is  
powered by a standard 6F22 9 V rechargeable battery lasting for up to 13 hours per charge. Charging contacts on the  
receiver body enable the battery inside the receiver to be charged on the CS 5 CU 50 charger with no need to remove  
the battery.  
Fig. 10: Front and top panels of the CS 5 IRR 7 infrared receiver.  
1
2
: TRS mini jack for connecting a pair of stereo headphones.  
ON: This key on the side of the receiver switches power to the receiver ON. The receiver will switch OFF automat-  
ically about 30 seconds after the infrared signal has stopped.  
3
BATTERY: This bi-color LED indicates the current battery status in operating and charging modes.  
• In operating mode, the LED indicates the current battery capacity and warns you that the battery needs charg-  
ing when battery capacity is low.  
• In charging mode, the LED is lit to indicate the battery is being charged and starts flashing when the battery is  
charged to capacity.  
Plastic collecting lens for the infrared receiving diode.  
VOLUME: This rotary control sets the volume of the headphones connected to the receiver.  
LANGUAGE SELECT: This rotary switch on the side of the receiver selects one of seven language channels. The  
actual number of languages available depends on the number of languages into which interpretation is provided.  
4
5
6
CS 5 User Manual  
- 38 -  
Section 7: Infrared Transmission System  
7.2.2 Using the Infrared Receiver  
1. Connect the headphones to the jack (1). Make sure to turn the VOLUME control (5) to its minimum posi-  
tion to avoid damaging your hearing by excessive sound levels.  
2. To switch power to the receiver on, press the <ON> key (2) on the receiver side panel.  
The BATTERY LED (3) provides the following information:  
Refer to  
fig. 10  
on page 37.  
LED…  
Status  
Required action  
…is lit green for 2 seconds after  
Battery is adequately charged for  
None.  
pressing <ON> , then flashes green. normal operation.  
…starts flashing red. Battery will be dead in about 15  
minutes.  
•
Charge battery as soon as pos-  
sible.  
…remains dark after pressing <ON>. • Battery is completely dis-  
charged.  
•
•
Charge battery as soon as pos-  
sible.  
Contact your nearest AKG Serv-  
ice Center or Distributor.  
•
There is no battery inside the  
receiver  
3. Use the LANGUAGE SELECT rotary switch (6) to select the desired language from the list of interpreted languages  
provided by the organizers (or by ear, if no such list is available).  
4. Use the VOLUME control (5) to set the volume level of your headphones just loud enough so you can hear clearly  
what is being said.  
Important:  
•
Do not turn the headphones volume up any higher than necessary. Listening to excessive sound lev-  
els on headphones may damage your hearing.  
(Refer to fig. 10 on page 37.) Never cover the collecting lens (4) above the infrared receiving diode. Cov-  
ering the lens (4) will cut the signal and may cause the receiver to switch off automatically.  
!
•
Note: The signal may fade in some spots within the conference room due to interference or shadow effects. If that  
happens, move away from such a spot.  
ꢀ
5. If the BATTERY LED (3) on the receiver top panel starts flashing, the battery will be dead soon. Return the receiver  
to conference staff. They will give you a receiver with a fully charged battery.  
6. You cannot switch power to the receiver off.The receiver will switch off automatically 30 seconds after the infrared  
signal has stopped.  
Note: The receiver will also switch off automatically before the battery is completely discharged to avoid damaging  
the battery.  
ꢀ
7.2.3 Replacing Batteries  
The infrared receiver is delivered with a 280 mAh 9 V NiMH rechargeable battery installed.  
Important:  
The battery cannot be replaced by the user. When the battery needs replacing, contact your nearest AKG  
Service Center or AKG Distributor.  
•
!
CS 5 User Manual  
- 39 -  
Section 7: Infrared Transmission System  
7.3 CS 5 CU 50 Charger/Storage Case  
7.3.1 General  
The CS 5 CU 50 is a combined charger and transport/storage unit in a rugged, lockable flight case. It allows you to store  
up to 50 CS 5 IRR 7 infrared receivers during a conference and charge the batteries inside them. Each charging slot  
has its own independent charging control circuit.  
Fig. 11: CS 5 CU 50 control panel and charging slots.  
1
DC 15V 4.6A: Input connector for the DC cable of the supplied dedicated power supply. The power supply oper-  
ates on any voltage from 100 to 240 VAC.  
2
3
4
FUSE: 5 A, fast-blow fuse.  
POWER: This red LED is lit to indicate that power to the charger is ON.  
Charging slot for charging the battery inside a receiver. The charger provides 50 charging slots.  
7.3.2 Charging Batteries  
1. Unlock and remove the lid from the flight case.  
Refer to  
2. Connect the DC cable on the supplied AC adapter to the DC 15V 4.6A jack on the CS 5 CU 50 charger.  
3. Connect the AC adapter to a convenient power outlet.  
fig. 11above.  
Important:  
•
To avoid any risk of damage, do not use any power supply other than the AC adapter included with the  
charger.  
To avoid any risk of damage, fire, or explosion, never insert a receiver with dry (non-rechargeable) bat-  
teries inside into any charging slot.  
!
•
4. Insert each receiver whose battery needs charging (BATTERY LED flashing) into a charging slot (4) with the charg-  
ing contacts facing the bottom of the charging slot.  
Charging will start automatically and the BATTERY LED on the receiver will be lit red constantly.  
As soon as the battery is charged to capacity, the BATTERY LED on the receiver will start flashing red to indicate  
the battery is being trickle-charged.  
CS 5 User Manual  
- 40 -  
Section 7: Infrared Transmission System  
5. Remove the receiver from the charging slot.  
Note: Charging time depends on battery capacity. It is approximately four hours for a 280 mAh 9 V NiMH recharge-  
able battery.  
ꢀ
7.3.3 Battery Care  
1. Always store the batteries inside the receivers in charged condition. Storing rechargeable batteries uncharged  
would significantly reduce their useful life.  
2. If you do not use a receiver for a long period of time, charge its battery to capacity every one or two months, no  
matter to what level the battery has been charged before. This is important because the battery will self-discharge  
even when the receiver is switched off.  
3. Do not store receivers in trickle-charging mode in the CU 50 indefinitely. This may reduce the usfeul life of the bat-  
tery inside the receiver. After a conference has ended, charge all receivers to capacity and switch power to the  
CU 50 off.  
CS 5 User Manual  
- 41 -  
Section 8: System Components  
Base Station  
CS5 BU  
Base Unit for up to 5,000 microphone stations, including PC Software, SERVICE CARD, printed Quick Start  
Manual, CD based User Manual  
Power supply for Base Unit and up to six microphone stations  
CS5 PS12  
CS MKAC EU European standard power cable  
CS MKAC US US standard power cable  
CS MKAC UK UK standard Power cable  
Microphone Stations  
CS5 DU  
Basic Delegate Station  
Voting/Chairperson Station  
Set of 10 ID Cards  
CS5 VU  
CS5 ID10  
CS5 IU  
Interpreter Station  
Goosenecks  
GN30 CS  
GN50 CS  
Screw-on Gooseneck, approx. 30 cm  
Screw-on Gooseneck, approx. 50 cm  
Microphone Capsules  
CK31  
CK32  
CK33  
CK47  
CK80  
Cardioid microphone capsule  
Omnidirectional microphone capsule  
Hypercardioid microphone capsule  
Shotgun microphone capsule  
Shotgun microphone capsule  
Cables  
CS5 MK1,25 1.25-m LAN cable  
CS5 MK2,5 2.5-m LAN cable  
CS5 MK5  
5-m LAN cable  
CS5 MK10 10-m LAN cable  
CS5 MK20 20-m LAN cable  
Infrared Transmission System  
CS5 IRT1  
CS5 IRT2  
CS5 IRR7  
Small infrared radiator  
Large infrared radiator  
Infrared receiver with stereo mini jack  
CS5 CU50 Charging and storage case for up to 50 CS5 IRR7 receivers  
CS 5 User Manual  
- 42 -  
Section 9: Specifications  
9.1 CS 5 BU  
9.1.1 General  
Minimum  
Nominal  
Maximum  
Unit  
DC 48V / 3A IN  
Input voltage  
Power requirement  
LINE IN (balanced)  
Input level  
46  
3
48  
-
50  
4
VDC  
W
-
-
0
20  
+6  
-
dBu  
kohms  
Impedance  
TELEPHONE IN (balanced)  
Input level  
Impedance  
-
-
0
20  
+6  
-
dBu  
kohms  
EFFECT IN (balanced)  
Input level  
Impedance  
-
-
0
20  
+6  
-
dBu  
kohms  
TAPE IN (unbalanced, stereo*)  
Input level  
Impedance  
-
-
-10  
20  
-4  
-
dBu  
kohms  
EXT. LANG IN (balanced)  
Input level  
Impedance  
-
-
0
20  
+6  
-
dBu  
kohms  
EXT. MIC. IN  
Input level  
Impedance  
Phantom power  
Output Levels  
-
-
-
-40  
20  
48  
-34  
-
-
dBu  
kohms  
V
LINE OUT (balanced)  
TELEPHONE OUT (balanced)  
EFFECT OUT (balanced)  
TAPE OUT (unbal., stereo*)  
Output Load Impedance  
-
-
-
-
-
0
0
0
-10  
1
+6  
+6  
+6  
-4  
-
dBu  
dBu  
dBu  
dBu  
kohm  
Output Frequency Range  
(-3dB)  
20  
-
20k  
Hz  
Headphone Output  
Power  
Load impedance  
Frequency range (-3dB)  
Physical Dimensions  
Height  
-
8
45  
90  
32  
-
200  
-
22k  
mW  
ohms  
Hz  
1/1.75/44  
18/482  
4.25/108  
3.2/1450  
U/in./mm  
in./mm  
in./mm  
lbs./g  
Width  
Depth inc. connector protrsion  
Weight  
* Use TRS plugs only. Connecting a TS plug would short the ring contact to ground and damage the device.  
CS 5 User Manual  
- 43 -  
Section 9: Specifications  
9.1.2 Connector Pinouts  
DC 48V / 3A IN  
DC power jack  
Pin no.  
Function  
Supply voltage  
GND  
1
2
LINE IN, TEL. IN, EXT. LANG. IN, EXT. MIC. IN  
3-pin female XLR  
Pin no.  
Function  
GND  
Audio -  
Audio +  
1
2
3
LINE OUT, TEL. OUT  
3-pin female XLR  
Pin no.  
Function  
GND  
Audio -  
Audio +  
1
2
3
EFFECT IN, EFFECT OUT  
1/4" TRS jacks  
Pin no.  
Tip  
Ring  
Function  
Audio inphase  
Audio  
Sleeve  
Ground  
TAPE IN, TAPE OUT  
TRS mini jacks  
Pin no.  
Tip  
Ring  
Function  
Audio inphase  
Audio  
Sleeve  
Ground  
HEADPHONE  
1/4" TRS jack  
Pin no.  
Tip  
Function  
Right  
Ring  
Left  
Sleeve  
Ground  
CS 5 User Manual  
- 44 -  
Section 9: Specifications  
SYSTEM  
8-pin RJ45  
Pin no.  
Function  
Data send +  
Data send -  
Data receive +  
48 VDC  
48 VDC  
Data receive -  
Ground  
1
2
3
4
5
6
7
8
Ground  
INFRA OUT  
BNC  
Pin no.  
Function  
PPM data signal  
Ground  
1
2
USB Port  
USB-B  
Pin no.  
Function  
+5 V  
USB data +  
USB data -  
Ground  
1
2
3
4
CS 5 User Manual  
- 45 -  
Section 9: Specifications  
9.2 CS 5 DU/VU  
9.2.1 General  
Minimum  
Nominal  
Maximum  
Unit  
Power Supply  
Supply voltage  
Power consumption  
Headphone Output  
Power  
Load impedance  
Frequency range (-3 dB)  
Physical Dimensions  
Signal/noise ratio  
Width  
46  
-
48  
1.5  
50  
3
V
W
-
8
45  
30  
32  
-
60  
-
22k  
mW  
ohms  
Hz  
70  
-
-
dB  
10.1/257  
5.8/147  
1.9/73  
in./mm  
in./mm  
in./mm  
Depth  
Height  
9.2.2 Connector Pinouts  
HEADPHONE  
1/4" TRS jack*  
Pin no.  
Tip  
Ring  
Function  
Right  
Left  
Sleeve  
Ground  
* Use stereo headphones with TRS plugs only. Connecting a TS plug would short the ring contact to ground  
and damage the device.  
SYSTEM  
8-pin RJ45  
Pin no.  
Function  
Data send +  
Data send -  
Data receive +  
48 VDC  
48 VDC  
Data receive -  
Ground  
1
2
3
4
5
6
7
8
Ground  
CS 5 User Manual  
- 46 -  
Section 9: Specifications  
CS 5 IU  
9.3.1 General  
Minimum  
Nominal  
Maximum  
Unit  
Power Supply  
Supply voltage  
46  
-
48  
1.5  
50  
3
V
W
Power consumption  
Microphone Input  
Frequency range (-3 dB)  
100  
60  
-
-
16k  
-
Hz  
dB  
Signal/noise ratio (digital  
signal measured with short-  
circuited input)  
Headphone Output  
Power  
Load impedance  
Physical Dimensions  
Width  
Depth  
Height  
Weight  
-
8
180  
32  
250  
-
mW  
ohms  
12.2/310  
6.0/152  
3.4/86  
in./mm  
in./mm  
in./mm  
lbs./g  
2.2/1000  
9.3.2 Connector Pinouts  
Headphone Output  
1/4" TRS jack  
Pin no.  
Function  
Tip  
Ring  
Right  
Left  
Sleeve  
Ground  
External Microphone  
1/4" TRS jack  
Pin no.  
Tip  
Ring  
Function  
Audio (hot)  
Audio  
Sleeve  
Ground  
CS 5 User Manual  
- 47 -  
Section 9: Specifications  
SYSTEM  
8-pin RJ45  
Pin no.  
Function  
Data send +  
Data send -  
Data receive +  
48 VDC  
48 VDC  
Data receive -  
Ground  
1
2
3
4
5
6
7
8
Ground  
9.4 CS 5 PS 12  
General  
Efficiency  
85% typical at 230 VAC & 100% load  
Input  
Input voltage  
Input frequency  
Input current  
Power factor  
Output  
90-264 VAC  
47-63 Hz  
1.85 A max  
Compliant with EN61000-3-2  
Output voltage  
Output power  
Short circuit protection  
Environmental  
Operating temperature  
Storage temperature  
Safety  
48 V  
72 W  
Continuous  
0°C to +65°C  
-20 °C to +85 °C  
Safety approvals  
EN60950-1, UL60950-1,  
CAN/CSA C22.2 No. 60950 cUL  
Dimensions  
Width x depth x height  
Weight  
2.29 (58.0) x 5.20 (132.0) x 1.18 (30.0) in. (mm)  
0.77 (350) lbs. (g)  
CS 5 User Manual  
- 48 -  
Section 9: Specifications  
9.5 CS 5 IRT 1 and CS 5 IRT 2  
CS 5 IRT 1  
CS 5 IRT 2  
IN  
OUT  
0-5 V / 50 ohms  
0-5 V / 50 ohms  
0-5 V / 50 ohms  
0-5 V / 50 ohms  
Power voltage  
200-240V 50/60Hz, 1.5A  
or 100-120V 50/60Hz, 3.15A  
(internally selectable)  
200-240V 50/60Hz, 1.5A  
or 100-120V 50/60Hz, 3.15A  
(internally selectable)  
Wavelength  
Radiated power  
Coverage angle (50% down)  
Coverage area  
Width  
Height  
Depth  
Weight  
870 nm  
2.5 W  
22 degrees  
870 nm  
3.8 W  
22 degrees  
6,450 sq.ft. / 600 m2  
10.3 in. / 264 mm  
6.3 in. / 160 mm  
3.0 in. / 77 mm  
5.6 lbs. / 2.5 kg  
10,750 sq.ft. / 1000 m2  
10.3 in. / 264 mm  
12.1 in. / 307 mm  
3.0 in. / 77 mm  
8.9 lbs. / 4 kg  
9.6 CS 5 IRR 7  
General  
Number of channels  
Receiving angle  
Power supply  
Battery life  
7
140 degrees  
280 mAh, 9 V NiMH rechargeable battery  
13 hours min  
Headphone Output  
Rated output power into 32 ohms  
Load impedance  
Physical Dimensions  
Height  
Width  
Depth  
Weight  
9 mW  
32 ohms min  
5.3 in. / 136 mm  
2.7 in. / 70 mm  
1.1 in. / 28 mm  
4.9 oz. / 140 g  
CS 5 User Manual  
- 49 -  
Section 9: Specifications  
9.7 CS 5 CU 50  
General  
Number of charging/storage slots  
Charging modes  
Power supply  
50  
Quick or trickle charging, automatically selected  
230 VAC, 15 VDC, 4.6 A  
Quick Charging Mode  
Charging current  
Trickle Charging Mode  
Charging current  
Physical Dimensions  
Height  
Width  
Depth  
Weight  
80 mA, continuous  
4 mA (avg.), pulsed  
7.5 in. / 190 mm  
23 in. / 585 mm  
19 in. / 483 mm  
3.1 lbs. / 14 kg  
9.8 Conformity  
This product conforms to the standards listed in the related Declaration of Conformity. To order a free copy of the Dec-  
laration of Conformity for this product, visit http://www.akg.com or contact [email protected].  
CS 5 User Manual  
- 50 -  
Mikrofone · Kopfhörer · Drahtlosmikrofone · Drahtloskopfhörer · Kopfsprechgarnituren · Akustische Komponenten  
Microphones · Headphones · Wireless Microphones · Wireless Headphones · Headsets · Electroacoustical Components  
Microphones · Casques HiFi · Microphones sans fil · Casques sans fil · Micros-casques · Composants acoustiques  
Microfoni · Cuffie HiFi · Microfoni senza filo · Cuffie senza filo · Cuffie-microfono · Componenti acustici  
Micrófonos · Auriculares · Micrófonos inalámbricos · Auriculares inalámbricos · Auriculares con micrófono · Componentes acústicos  
Microfones · Fones de ouvido · Microfones s/fios · Fones de ouvido s/fios · Microfones de cabeça · Componentes acústicos  
AKG Acoustics GmbH  
Lemböckgasse 21–25, A-1230 Vienna/AUSTRIA, phone: (+43-1) 86654-0*  
e-mail: [email protected]  
For other products and distributors worldwide visit www.akg.com  
Technische Änderungen vorbehalten. Specifications subject to change without notice. Ces caractéristiques sont susceptibles de modifications.  
Ci riserviamo il diritto di effettuare modifiche tecniche. Nos reservamos el derecho de introducir modificaciones técnicas. Especificações sujeitas  
a mudanças sem aviso prévio.  
10/09/9100 U 13150  

Fisher Paykel Cooktop CE244C User Manual
Digi NS9215 User Manual
Dell CU904 A00 User Manual
Daewoo 21Q1 User Manual
Cypress Perform CY7C1426BV18 User Manual
Cypress CY7C038V User Manual
Asus Motherboard Z87 DELUXE User Manual
Asus A8R MVP User Manual
Apollo SA 02 015 User Manual
Abit AMD ATHLON KV8 PRO User Manual