USER MANUAL
17” Compact Panel
DI170S01-A01
TFT Display + Backlight inverter + RGB board in one chassis
Orderable P/N: SA-02-015
Rev 1
May 23, 2005
The information given in this document is carefully checked and believed to be reliable. However, Apollo takes no
response for any failure or product damage caused by the application of this information. Please check all
connections carefully with the data sheet. Apollo products are not intended for use in systems in which failures of
product could result in personal injury. All mentioned trademarks are registered trademarks of their owner.
All specifications are subject to change without notification.
Apollo Display Technologies, LLC
85 Remington Blvd.
Ronkonkoma, NY 11779
USA
Tel.: 631-580-4360
Fax: 631-580-4370
E-Mail: [email protected]
flatpanel displays
and solutions
User Manual
DI170S01-A01
1 Revision History
Date
Rev.No.
Description
Page
10.02.2005
23.05.2005
0
1
First release of datasheet
Final release
2 General Description
The DI170S01-A01 from Distec’s CompactPanel Series is an open frame monitor providing an analog RGB interface for
17” SXGA TFT LCD panels with a high quality screen image. This monitor supports from VGA to UXGA resolution at a
maximum of 85Hz refresh rate (refer to point 8.1) with automatic up- and downscaling function to full screen size.
It gives a lot of convenience to the user in installing various applications such as gaming, amusement, industry and so
on and accessing the GUI (Graphic User Interface).
The DI170S01-A01 is a
certified product.
3 Absolute Maximum Ratings
ITEM
Model Name
LCD Module
DESCRIPTION
DI170S01-A01
LTM170EU-L21
REMARKS
Refer to the clause 5.1 Panel
Specification
Input Signal
Resolution
Analog RGB
DC 12V/2.6A *
* Measured at 23°C ambient temperature
Horizontal: Typ. 64, Max. 82.1 KHz
Vertical: Typ. 60, Max. 77 Hz
Analog RGB : VGA/SVGA/XGA/SXGA/UXGA
DC Jack, KEY Connector, RGB Connector
5 Buttons Controls
Special timing available
1600x1200 @ 60Hz Max.
Receptacle
User Controls
Image Scaler
Power Consumption
Dimension
Plug & Play
gm2121
31W Max *
Genesis Microchip
* Measured at 23°C ambient temperature
Refer to the clause 6.1
VESA
DDC 2B
Power Management
Supports VESA DPMS
DI170S01-A01
Rev 1
Page 3 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
4 Absolute Ratings of Environment
Item
Symbol
TSTG
TOPR
Min.
-25
0
Max.
60
50
Unit
°C
°C
Note
(1)
(1)
Storage temparature
Operating temparature
(Glass surface temperature)
Shock (non-operating)
Vibration (non-operating)
Snop
Vnop
-
-
50
1.5
G
G
(2), (4)
(3), (4)
Note
(1) Temperature and relative humidity range are shown in the figure below.
90 % RH Max. (40 °C ≥ Ta)
Maximum wet-bulb temperature at 39 °C or less. (Ta > 40 °C) No condensation.
(2) 11 ms, sine wave, one time for ±X, ±Y, ±Z axis
(3) 10-300 Hz, Sweep rate 10 min, 30 min for X, Y, Z axis
(4) At vibration and shock test, the fixture which holds the module to be tested has to be hard and rigid enough so
that the module would not be twisted or bent by the fixture.
DI170S01-A01
Rev 1
Page 4 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
5 Electrical Specification
5.1 Panel Specification
Item
Description
Unit
Type No.
Size
Samsung LTM170EU-L21
17” Diagonal
Inch
mm
Active Display Area
Number of Pixels
Pixel Arrangement
Pixel Pitch
337.92 x 270.336
1280 (H) x 1024 (V)
RGB Vertical Stripe
0.264 x 0.264
mm
Color Depth
Surface Treatments
Viewing Angle
16.2M True Color
Hard Coating (3H), Haze 25%
Horizontal :
Ө L
Ө R
Φ H
Φ L
75
75
75
60
degree
Vertical :
Contrast Ratio
Response Time
(CR≥ 10)
Typ. 700 : 1
Rise time (tr) : 2 ms(Typ.)
Fall time (tf) : 6 ms(Typ.)
Typ. 300 cd/m2
Average Brightness
Frame Rate
Typ. 60Hz, Max. 77Hz
Panel Dimension
CCFL
(WHD) 358.5 x 296.5 x 17.5
4 (2 Dual)
mm
5.2 Input Signal Characteristics
Input Signal
DC input
Description
DC Voltage
Power
Unit
Vdc
Watts
Min
11.4
Typical Max
Remarks
12
26
12.6
31
for full Option
Consumption
Video(SOG)
Sync Voltage
Horizontal
Frequency
Vertical
15Pin D-Sub
Vp-p
Vp-p
kHz
0.7
5.0
64
1.0
75Ω Terminated
56.7
55
82.082 Depends on Mode
77 Depends on Mode
Hz
60
Frequency
5.3 Power Management
VESA DPMS standard is applied for power management control
Mode
HSync.
VSync.
LED (red)
LED (grn)
Power Consumption
(nominal)
< 31 W
On
Active
Inactive
Active
Active
Active
Inactive
Inactive
Off
On
Off
Off
Off
Stand-by
Suspend
Off
Blinking
Blinking
Off
< 3 W
Inactive
DI170S01-A01
Rev 1
Page 5 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
5.4 Connector Pin Assignment
5.4.1 CN6: DC Input
Part No.
PHR-4
(JST)
Pin No.
1,2
3,4
Description
GND
Vcc(12V/5A)
Remarks
Remarks
5.4.2 CN1: Analog RGB Input
Part No.
S13B-PH-SM3-TB
(JST)
Pin No.
1
2
Description
CABLE DETECT
DDC SDA
3
DDC SCL
4
RED GND
5
6
7
8
RED INPUT
GREEN GND
GREEN INPUT
BLUE GND
9
BLUE INPUT
NC
VERTICAL SYNC
SYNC GND
HORIZONTAL SYNC
10
11
12
13
5.4.3 CN2: Key Connector
Part No.
Pin No.
Description
Remarks
53261-1490
(MOLEX)
1
2
LED2
LED1
3
GND
4
POWER
5
GND
6
MENU
7
RIGHT (Brightness +)
8
9
NC
NC
Option in 8 keys
Option in 8 keys
10
11
12
13
14
LEFT (Brightness -)
EXIT
AUTO
GND
+3.3V (100mA)
DI170S01-A01
Rev 1
Page 6 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
6 Mechanical Specification
6.1 Front view
DI170S01-A01
Rev 1
Page 7 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
6.2 Back Side View
DI170S01-A01
Rev 1
Page 8 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
6.3 Side View 1
DI170S01-A01
Rev 1
Page 9 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
6.4 Side View 2
DI170S01-A01
Rev 1
Page 10 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
7 Operation Guide
7.1 Installation
This monitor is designed for RGB monitor using 17” TFT LCD panel.
This section provides some guidelines for assembly and preparation of a finished display solution.
Before proceeding, it is important to familiarize yourself with the parts making up a system and the various
connectors, mounting holes and general layout of the monitor.
Please follow the below procedure.
1. Appearance Inspection
Please check the monitor whether it is damaged in appearance or not during transportation.
And assemble this monitor to your system or applications.
2. Signal Inputs Connection
Analog input is available. Please refer to the clause 5.4 Connector
Pin Assignment and connect the signal what you want to apply to the monitor.
Especially, the Analog RGB cable may affect the visual characteristics and regulatory emission test. So, a
suitably shielded cable should be used.
3. Power Input Connection
Refer to the 5.4 Connector Pin Assignment and connect the power input cable to the monitor.
Every connection is done but you should consider electrical insulation, grounding, EMI shielding and heat &
ventilation.
4. Apply Power
Apply power and turn on the monitor and refer to the following clause.
7.2 OSD Adjustment
DI170S01-A01 gives a various and very easy graphics interface to its users. Users have easy access to the functions that
they want to adjust. Be sure that your system’s power and LED are turned on, before the OSD controls are being used.
7.2.1 Key Name and Function
Key name
Power
Description
Turns ON/OFF the system
Menu
- Opens the main menu
- Confirmation button for selected menu points
- Back to the sub menu
Exit
Left
- Goes directly to the exit icon, when the OSD main or sub menu is shown.
The exit icon must still be confirmed via the Menu – button to leave the OSD menu!
- Activates directly the brightness menu
- To decrease setting bars
- Menu icon selection to the left
Right
- Activates directly the contrast menu
- To increase setting bars
- Menu icon selection to the right
Accessing the menu system
1. With the OSD off, push the Menu button to activate the main OSD menu.
2. Use the Left and Right buttons to move through the main menu. To select a desired sub menu, press the
Menu button after your selection. The selection tabs are also highlighted and explained via onscreen text in
the upper right of the OSD screen.
DI170S01-A01
Rev 1
Page 11 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
3. After selecting a sub menu, use the Left or Right buttons to move through the sub menu. To select a setting
icon, press the Menu button after your selection. The selected icons are highlighted and explained via
onscreen text in the lower right of the OSD screen.
4. There are two types of icons: Some have a single function and must be confirmed with the Menu button, the
other option are setting bars. Once a setting bar appears, it can be increased or decreased via the Left and
Right buttons. The setting bar moves and the numeric value indicator changes to reflect your adjustments.
NOTE: The numeric value indicator is provided as a point of reference only and has nothing to do with a real
measurement.
5. There are many ways to close the OSD menu:
- Waiting some seconds (timeout). This time can be adjusted as needed in one of the menus.
- In the main and sub menu, press the Exit button. This highlights the “Exit” icon in the menu. Then press the
Menu button to leave the OSD menu.
- After an Autoadjust and confirmation the OSD menu closes automatically.
- After adjusting a setting, press the Menu button to go back to the sub menu, then press the Exit button or
use the Right button to select the “Exit” icon. Confirm via the Menu button and the OSD turns off.
7.2.2 OSD Structure
Main Menu
Brightness
Contrast
Brightness
Contrast
Black Level
Color
Auto Color
sRGB
Color Temperature
CMY
User
4200K
5000K
6500K
7500K
9300K
Flesh Tone
Hue
Saturation
Image
Autoconfiguration
Width
Phase
Horizontal Position
Vertical Position
OSD Timeout
OSD Hor. Position
OSD Ver. Position
OSD Size
Tools
OSD
Factory Reset
Sharpness
Fast
Autoconfiguration
Normal
DI170S01-A01
Rev 1
Page 12 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
7.2.3 Window structure
Input Timing
Main Menu
Info
Main
Menu
Exit Icon
Sub Menu
Info
Sub Menu
Icons
Available OSD controller boards
7.2.4 Detailed description of the On-Screen-Menu
The following paragraphs describe the OSM main and sub-menus and the associated functions.
Adjusted menu items will be saved if:
•
•
•
•
the OSM is closed by selecting and confirming the Exit Menu icon
toggling the sleep mode with the Power Key
selecting the green smiley after Autoconfiguration in Color or Image menu
resetting the color value to sRGB default
DI170S01-A01
Rev 1
Page 13 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
Brightness – Contrast
-
-
-
Brightness: Adjusts display brightness. If supported, brightness will be regulated using the connected inverter.
Contrast: Adjusts image contrast
Black Level: Adjusts image black level
Color
-
Autoconfiguration: Performs a calibration of the ADC for optimum colors. For best result, black and white level
should be present in the image.
-
-
sRGB: Return to default sRGB color values (also activates sRGB color space)
Color Temperature: Allows you to choose different values for the color temperature including a user defined
setting in RGB color space.
-
-
-
-
CMY: Modify the proportion of cyan, magenta and yellow in the image (also activates CMY color space)
Flesh Tone: Adjusts flesh tone of the image (requires sRGB color space)
Hue: Adjusts hue of the image (requires sRGB color space)
Saturation: Adjusts saturation of the image (requires sRGB color space)
DI170S01-A01
Rev 1
Page 14 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
Image
-
-
-
-
-
Autoconfiguration: Optimizes the displayed image. Adjusts phase and image position automatically.
Width: Adjusts image width.
Phase: Adjusts image phase.
Horizontal position: Adjusts horizontal image position.
Vertical position: Adjusts vertical image position
Tools & OSD
-
OSD
•
OSD Timeout: The OSD vanishes after a certain time of inactivity. Values of 2-16s are possible
•
•
•
OSD Horizontal Position: Adjusts position horizontally
OSD Vertical Position: Adjusts position vertically
OSD Size: Doubles size of OSD (only valid if display resolution is 2 times larger than the OSD size)
-
-
-
Factory reset: Return to factory default values
Sharpness: Modifies the image filtering with shrinking and expansion
Autoconfiguration Type
•
•
Fast: Quick autoadjustment method (coarse adjust for fast resolution switching, like during bootup)
Normal: Standard autoadjustment method (fine adjustment once the system is displayed properly)
DI170S01-A01
Rev 1
Page 15 of 16
Product No. : SA-02-015
May 23, 2005
User Manual
DI170S01-A01
8 Appendix
8.1 Standard Timing Chart
Total
Horizontal
Frequency
(KHz)
H-
Vertical
Freq
V-
Pixel
Failsafe
Mode
Mode
Active Resolution
Pixels
Pol.
Pol.
Clock
(Hz)
VGA
640x350 @ 85Hz
640x400 @ 85Hz
720x400 @ 85Hz
640x480 @ 60Hz
640x480 @ 72Hz
640x480 @ 75Hz
640x480 @ 85Hz
800x600 @ 56Hz
800x600 @ 60Hz
800x600 @ 72Hz
800x600 @ 75Hz
800x600 @ 85Hz
1024x768 @ 60Hz
1024x768 @ 70Hz
1024x768 @ 75Hz
1024x768 @ 85Hz
1152x864 @ 75Hz
1280x1024 @ 60Hz
1280x1024 @ 75Hz
640x350 @ 70Hz
640x400 @ 70Hz
720x350 @ 70Hz
720x400 @ 70Hz
1024x768 @ 72Hz
1024x768 @ 87Hz(i)
640x480 @ 67Hz
832x624 @ 75Hz
1024x768 @ 60Hz
1280x1024 @ 60Hz
1280x1024 @ 72Hz
1280x1024 @ 67Hz
1280x960 @ 60Hz
1280x1024 @ 85Hz
1280x960 @ 85Hz
640x400 @ 56Hz
1152x864 @ 70Hz
1600x1200 @ 60Hz
1280x768 @ 60Hz
1280x720 @ 60Hz
832x445
832x445
37,861
37,861
37,927
31,469
37,861
37,5
P
N
N
N
N
N
N
N/P
P
85,08
85,08
85,039
59,94
72,809
75
N
P
31,5
31,5
35,5
25,175
31,5
31,5
36
X
X
X
936x446
P
800x525
N
N
N
N
N/P
P
832x520
840x500
832x509
43,269
35,156
37,879
48,077
46,875
53,674
48,363
56,476
60,023
68,677
67,5
85,008
56,25
60,317
72,188
75
X
SVGA
XGA
1024x625
1056x628
1040x666
1056x625
1048x631
1344x806
1328x806
1312x800
1376x808
1600x900
1688x1066
1688x1066
800x449
36
40
P
P
50
P
P
49,5
56,25
65
P
85,061
60,004
70,069
75,029
84,997
75
P
X
X
N
N
P
N
N
P
75
78,75
94,5
108
P
P
P
P
SXGA
63,981
79,976
31,469
31,469
31,469
31,469
57,515
35,522
35
P
60,02
75,025
70,086
70,086
70,087
70,087
72,1
P
108
P
P
135
EGA
CGA
DOS
DOS
XGA
XGA
P
N
P
25,175
25,175
28,322
28,322
75
800x449
N
P
900x449
N
P
900x449
N
P
1304x798
1264x817
864x525
P
P
43,479
66,667
74,551
60,001
59,978
72,005
67,003
60
P
44,9
30,24
57,283
64
N
N
N
N
N
N
P
N
N
N
N
N
N
P
SVGA
XGA
1152x667
1312x813
1708x1056
1728x1085
1696x1056
1800x1000
1728x1072
1728x1011
49,725
48,78
X
SXGA
63,337
78,125
70,755
60
125
135
SXGA
120
108
91,146
85,934
P
85,024
85,002
P
157,5
148,5
X
X
P
P
VGA
1600x900
P
70
P
UXGA
X
DI170S01-A01
Rev 1
Page 16 of 16
Product No. : SA-02-015
May 23, 2005
|