Nokia 8310 User Manual

Electronic user’s guide released subject to "Nokia User’s Guides Terms and Conditions, 7th June, 1998"

User’s Guide

9360316

Issue 2

Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect

damages howsoever caused.

The contents of this document are provided "as is". Except as required by applicable law, no warranties of any kind, either express or

implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in

relation to the accuracy, reliability or contents of this document. Nokia reserves the right to revise this document or withdraw it at

any time without prior notice.

The availability of particular accessories may vary by region. Please check with the Nokia dealer nearest to you. Please dispose of

batteries properly.

9360316 / Issue 2

Contents

Contents ............................................................................................................................................. 4

FOR YOUR SAFETY........................................................................................................................... 10

General information........................................................................................................................ 13

Stickers in the sales package ....................................................................................................................................................... 13

Access codes ..................................................................................................................................................................................... 13

Overview of the functions in the phone........................................................................................ 15

GPRS (General Packet Radio Service) ........................................................................................................................................ 15

HSCSD (High Speed Circuit Switched Data)............................................................................................................................ 16

WAP (Wireless Application Protocol)......................................................................................................................................... 16

Radio ................................................................................................................................................................................................... 17

Voice features................................................................................................................................................................................... 17

1. Your phone................................................................................................................................... 18

Keys and connectors....................................................................................................................................................................... 18

Standby mode................................................................................................................................................................................... 19

2. Getting started............................................................................................................................. 21

Installing the SIM card and the battery.................................................................................................................................... 21

Charging the battery ...................................................................................................................................................................... 24

Switching the phone on and off ................................................................................................................................................. 24

Keypad lock (Keyguard).................................................................................................................................................................. 25

Changing the covers....................................................................................................................................................................... 27

3. Call functions............................................................................................................................... 29

Making a call .................................................................................................................................................................................... 29

Speed dialling a phone number ............................................................................................................................................... 31

Making a conference call........................................................................................................................................................... 31

Answering or rejecting an incoming call .................................................................................................................................. 32

Call waiting.................................................................................................................................................................................... 32

Options during a call....................................................................................................................................................................... 32

4. Writing text ................................................................................................................................. 34

Setting predictive text input on or off....................................................................................................................................... 34

Using predictive text input............................................................................................................................................................ 34

Writing compound words........................................................................................................................................................... 36

Using traditional text input .......................................................................................................................................................... 36

Tips for writing text......................................................................................................................................................................... 36

5. Phone book (Names) ................................................................................................................... 38

Selecting the phone book settings.............................................................................................................................................. 38

Saving names and phone numbers (Add name)...................................................................................................................... 39

Saving multiple numbers and text items per name............................................................................................................ 39

Changing the default number............................................................................................................................................... 40

Searching for a name in the phone book.................................................................................................................................. 40

Editing a name, number or text item......................................................................................................................................... 41

Erasing names and numbers......................................................................................................................................................... 41

Copying phone books...................................................................................................................................................................... 41

Sending and receiving a business card...................................................................................................................................... 42

Speed dialling.................................................................................................................................................................................... 43

Voice dialling..................................................................................................................................................................................... 43

Adding a voice tag ....................................................................................................................................................................... 44

Making a call by using a voice tag.......................................................................................................................................... 44

Replaying, changing or erasing a voice tag.......................................................................................................................... 45

Service numbers ............................................................................................................................................................................... 45

Caller groups ..................................................................................................................................................................................... 45

6. Using the menu............................................................................................................................ 47

Accessing a menu function........................................................................................................................................................... 47

List of menu functions................................................................................................................................................................... 48

7. Menu functions............................................................................................................................ 50

Messages (Menu 1)......................................................................................................................................................................... 50

Writing and sending messages................................................................................................................................................. 50

Options for sending a message............................................................................................................................................. 51

Text and picture templates........................................................................................................................................................ 51

Inserting a text template or a picture into a message .................................................................................................. 52

Reading and replying to a message........................................................................................................................................ 52

Inbox and outbox folders........................................................................................................................................................... 53

Erasing the messages.................................................................................................................................................................. 53

Archive folder and my folders .................................................................................................................................................. 54

Voice messages............................................................................................................................................................................. 54

Info messages................................................................................................................................................................................ 55

Service command editor............................................................................................................................................................. 55

Message settings.......................................................................................................................................................................... 55

Call register (Menu 2)..................................................................................................................................................................... 56

Recent calls lists........................................................................................................................................................................... 56

Call counters and call timers.................................................................................................................................................... 57

Profiles (Menu 3) ............................................................................................................................................................................. 58

Settings (Menu 4)........................................................................................................................................................................... 59

Alarm clock .................................................................................................................................................................................... 59

Time settings ................................................................................................................................................................................. 60

Clock............................................................................................................................................................................................. 60

Auto update of date and time .............................................................................................................................................. 60

Call settings................................................................................................................................................................................... 60

Call divert.................................................................................................................................................................................... 60

Anykey answer........................................................................................................................................................................... 61

Automatic redial........................................................................................................................................................................ 61

Speed dialling............................................................................................................................................................................. 61

Call waiting service .................................................................................................................................................................. 61

Summary after call ................................................................................................................................................................... 62

My number sending.................................................................................................................................................................. 62

Line for outgoing calls............................................................................................................................................................. 62

Phone settings............................................................................................................................................................................... 62

Language ..................................................................................................................................................................................... 62

Cell info display......................................................................................................................................................................... 63

Welcome note............................................................................................................................................................................ 63

Network selection..................................................................................................................................................................... 63

Confirm SIM service actions.................................................................................................................................................. 63

Help text activation.................................................................................................................................................................. 63

Start-up tone.............................................................................................................................................................................. 64

Tone settings.................................................................................................................................................................................. 64

Accessory settings........................................................................................................................................................................ 65

GPRS modem settings................................................................................................................................................................. 65

Security settings ........................................................................................................................................................................... 66

Restore factory settings.............................................................................................................................................................. 67

Games (Menu 5)............................................................................................................................................................................... 67

Starting a game and game options......................................................................................................................................... 67

Game services and game settings............................................................................................................................................ 68

Calculator (Menu 6) ........................................................................................................................................................................ 69

Making a currency conversion.................................................................................................................................................. 69

To-do list (Menu 7).......................................................................................................................................................................... 70

Calendar (Menu 8)........................................................................................................................................................................... 71

Making a calendar note.............................................................................................................................................................. 71

When the phone alarms for a note ......................................................................................................................................... 72

Infrared (Menu 9) ............................................................................................................................................................................ 72

Radio (Menu 10).............................................................................................................................................................................. 73

Tuning a radio channel............................................................................................................................................................... 74

Using the radio ............................................................................................................................................................................. 75

Extras (Menu 11) ............................................................................................................................................................................. 76

Voice recorder ............................................................................................................................................................................... 76

Recording.................................................................................................................................................................................... 76

List of recordings ...................................................................................................................................................................... 77

Voice commands .......................................................................................................................................................................... 77

Countdown timer......................................................................................................................................................................... 78

Stopwatch...................................................................................................................................................................................... 78

Time observation and time splitting ................................................................................................................................... 78

Lap times..................................................................................................................................................................................... 79

Viewing and erasing times..................................................................................................................................................... 79

Mobile Internet services, WAP (Menu 12)................................................................................................................................ 80

Basic steps for accessing and using WAP services............................................................................................................. 80

Setting up the phone for a WAP service............................................................................................................................... 80

Saving the service settings received as a text message................................................................................................ 81

Keying in the service settings manually............................................................................................................................. 81

Settings when GSM data is the selected data bearer.................................................................................................... 82

Settings when GPRS is the selected data bearer............................................................................................................. 83

Making a connection to a WAP service................................................................................................................................. 83

Browsing the pages of a WAP service.................................................................................................................................... 85

General guidelines for using the phone keys.................................................................................................................... 85

Ending a WAP connection......................................................................................................................................................... 86

Appearance settings of WAP browser.................................................................................................................................... 86

Download settings....................................................................................................................................................................... 87

Bookmarks...................................................................................................................................................................................... 87

Receiving a bookmark ............................................................................................................................................................. 88

Service inbox.................................................................................................................................................................................. 88

To set the phone to receive service messages.................................................................................................................. 89

The cache memory ....................................................................................................................................................................... 89

Authority certificates .................................................................................................................................................................. 90

Viewing the list of authority certificates........................................................................................................................... 90

Security indicator...................................................................................................................................................................... 90

SIM services (Menu 13).................................................................................................................................................................. 91

8. Data and fax communication ..................................................................................................... 92

Communication applications and modem drivers.................................................................................................................. 92

PC Suite........................................................................................................................................................................................... 92

Modem setup................................................................................................................................................................................. 94

GPRS - General Packet Radio Service ................................................................................................................................. 94

HSCSD - High Speed Circuit Switched Data..................................................................................................................... 94

Using data communication applications............................................................................................................................... 94

9. Battery statements ...................................................................................................................... 96

Charging and Discharging............................................................................................................................................................. 96

CARE AND MAINTENANCE............................................................................................................. 98

IMPORTANT SAFETY INFORMATION.............................................................................................. 99

FOR YOUR SAFETY

Read these simple guidelines. Breaking the rules may be dangerous or illegal. Further detailed information is given

in this manual.

Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or

danger.

ROAD SAFETY COMES FIRST

Don’t use a hand-held phone while driving.

INTERFERENCE

All wireless phones may get interference, which could affect performance.

SWITCH OFF IN HOSPITALS

Follow any regulations or rules. Switch the phone off near medical equipment.

SWITCH OFF IN AIRCRAFT

Wireless devices can cause interference in aircraft.

SWITCH OFF WHEN REFUELLING

Don’t use the phone at a refuelling point. Don’t use near fuel or chemicals.

SWITCH OFF NEAR BLASTING

Don’t use the phone where blasting is in progress. Observe restrictions, and follow any regulations or

rules.

USE SENSIBLY

Use only in the normal position. Don’t touch the antenna unnecessarily.

QUALIFIED SERVICE

Only qualified personnel may install or repair phone equipment.

ACCESSORIES AND BATTERIES

Use only approved accessories and batteries. Do not connect incompatible products.

CONNECTING TO OTHER DEVICES

When connecting to any other device, read its user’s guide for detailed safety instructions. Do not

connect incompatible products.

BACKUP COPIES

Remember to make backup copies of all important data.

WATER-RESISTANCE

Your phone is not water-resistant. Keep it dry.

CALLING

Ensure the phone is switched on and in service. Enter the phone number, including the area code, then

press

. To end a call, press

. To answer a call, press

EMERGENCY CALLS

Ensure the phone is switched on and in service. Press

as many times as needed (e.g. to exit a call,

to exit a menu, etc.) to clear the display. Enter the emergency number, then press

location. Do not end the call until told to do so.

. Give your

■ Network Services

The wireless phone described in this guide is approved for use on the EGSM 900 and GSM 1800 network.

Dualband is a network dependent feature. Check with your local service provider if you can subscribe to and use this

feature.

A number of features included in this guide are called Network Services. These are special services that you arrange

through your wireless service provider. Before you can take advantage of any of these Network Services, you must

subscribe to them through your service provider and obtain instructions for their use from your service provider.

Note: Some networks may not support all language-dependent characters and/or services.

■ About accessories

Check the model number of any charger before use with this device. This device is intended for use when supplied

with power from ACP-7, ACP-8 and LCH-9.

Warning: Use only batteries, chargers and accessories approved by the phone manufacturer for use with

this particular phone model. The use of any other types may invalidate any approval or warranty applying

to the phone, and may be dangerous.

For availability of approved accessories, please check with your dealer.

When you disconnect the power cord of any accessory, grasp and pull the plug, not the cord.

General information

■ Stickers in the sales package

The stickers contain important information for services and customer support purposes.

Attach the

sticker to your warranty card.

sticker to the Nokia Club Invitation Card supplied in the sales package.

■ Access codes

• Security code (5 digits): The security code protects your phone against unauthorised use, and is

supplied with the phone. The preset code is 12345. Change the code in the Settings menu, see

Security settings on page 66. Keep the new code secret and in a safe place separate from your

phone.

Set the phone to request the code, see Security settings on page 66.

• PIN code (4 to 8 digits): The PIN (Personal Identification Number) code protects your SIM card

against unauthorised use. The PIN code is usually supplied with the SIM card.

Set the phone to request the PIN code each time the phone is switched on, see Security settings on

page 66.

• PIN2 code (4 to 8 digits): The PIN2 code may be supplied with the SIM card and is required to

access some functions, such as charging unit counters.

• PUK and PUK2 codes (8 digits): The PUK (Personal Unblocking Key) code is required to change a

blocked PIN code. The PUK2 code is required to change a blocked PIN2 code.

If the codes are not supplied with the SIM card, contact your local service provider for the codes.

• Barring password: The barring password is needed when using the Call barring service, see Security

settings on page 66. You can obtain the password from your service provider.

Overview of the functions in the phone

The Nokia 8310 phone provides many functions which are very handy for daily use, such as Calendar,

Clock, Alarm clock, Countdown timer, Calculator, Games, and many more.

Also a range of Nokia Xpress-on^TMcolour covers is available for your phone. To change the covers, see

Changing the covers on page 27.

■ GPRS (General Packet Radio Service)

GPRS is a technology that allows mobile phones to be used for sending and receiving data over the

mobile network. GPRS as such is a data bearer that enables wireless access to data networks like the

Internet. The applications that use GPRS are WAP, SMS messaging and the GPRS dial-up (for example,

Internet and e-mail).

Before you can use GPRS technology

• You need to subscribe to the GPRS service.

For availability and subscription to GPRS service, contact your network operator or service provider.

• You need to save the GPRS settings for each of the applications used over GPRS.

See Setting up the phone for a WAP service on page 80.

See Message settings on page 55.

See GPRS modem settings on page 65 and Data and fax communication on page 92.

Pricing for GPRS and applications

Both the active GPRS connection and the applications used over GPRS, for example using WAP

services, sending and receiving data and SMS messages, are priced. For more detailed information on

pricing, contact your network operator or service provider.

■ HSCSD (High Speed Circuit Switched Data)

The phone enables you to use GSM high-speed data services. You can use high-speed functionality

when your phone is connected to a computer via an IR connection, and when the modem drivers

supporting high-speed data software are installed on your computer and selected as an active modem.

For availability and subscription to high-speed data services, contact your network operator or service

provider.

See also Data and fax communication on page 92.

■ WAP (Wireless Application Protocol)

You can access various WAP services such as banking, news, weather reports and flight times. These

services are specially designed for mobile phones and they are maintained by WAP service providers.

Check the availability of WAP services, pricing and tariffs with your network operator and/or the

service provider whose service you wish to use. Service providers will also give you instructions on how

to use their services.

See Mobile Internet services, WAP (Menu 12) on page 80.

■ Radio

Your phone has an integrated FM radio. You can listen to the radio by using a headset. See Radio (Menu

10) on page 73.

■ Voice features

Your phone offers you the following voice features:

• Voice dialling - to make a call by using a voice tag, see Voice dialling on page 43.

• Voice commands - to activate certain functions in your phone that are listed in the Voice

commands menu, see Voice commands on page 77.

• Voice recorder - to make voice recordings, see Voice recorder on page 76.

1. Your phone

■ Keys and connectors

1.Power key,

Switches the phone on and off.

While in the phone book or in menu functions, or when the

keypad is locked, pressing the power key briefly turns the phone’s

display lights on for approximately 15 seconds.

2.Volume keys

The upper key increases and the lower key decreases the earpiece

(and headset) volume.

3.Selection keys,

and

The function of the keys depends on the guiding text shown on

the display above the keys, for example Menu and Names in

standby mode.

4.Scroll keys,

and

Enables scrolling through names, phone numbers, menus or

settings.

dials a phone number, and answers a call. In standby mode

it shows the most recently called number.

ends an active call. Exits from any function.

enter numbers and characters. Pressing and holding

calls your voice

mailbox.

and

are used for various purposes in different functions.

1 - Charger connector

2 - Headset connector

3 - Infrared (IR) port

■ Standby mode

When the phone is ready for use, and no characters have been entered by the

user, the phone is in standby mode.

Selection keys in standby mode are Menu and Names.

xxxxIndicates in which cellular network the phone is currently being used.

Shows the signal strength of the cellular network at your current location. The higher the bar,

the stronger the signal.

Shows the battery charge level. The higher the bar, the more power in the battery.

Other essential indicators in standby mode:

You have received one or several text or picture messages. See Reading and replying to a

message on page 52.

You have received one or several voice messages. See Voice messages on page 54.

The phone’s keypad is locked. See Keypad lock (Keyguard) on page 25.

The phone does not ring at an incoming call or text message when Incoming call alert is set to

Off and Message alert tone is set to Off. See Tone settings on page 64.

The alarm clock is set to On. See Alarm clock on page 59.

The countdown timer is running. See Countdown timer on page 78.

The stopwatch timing is running in the background. See Stopwatch on page 78.

A GPRS dial-up connection is established, refer to GPRS modem settings on page 65. The

indicator is shown on the top left of the display.

There is an incoming or outgoing call during a GPRS dial-up connection. The GPRS connection

is suspended.

All your calls are diverted to another number, Divert all voice calls. If you have two phone lines,

the divert indicator for the first line is

and for the second line

. See Call divert on page

60.

Calls are limited to a closed user group (network service). See Security settings on page 66.

2. Getting started

■ Installing the SIM card and the battery

•

Keep all miniature SIM cards out of the reach of small children.

• The SIM card and its contacts can easily be damaged by scratches or bending, so be careful when

handling, inserting or removing the card.

• Before installing the SIM card, always make sure that the phone is switched off and then remove

the battery.

1. With the back of the phone facing you, press the back cover release button (1) and slide the back

cover off the phone (2).

Remove the battery by lifting it from the finger grip (3).

2. To release the SIM card holder, slightly lift the front edge of the cover on the card holder (4) and

slide it backwards (5). Open the cover (6).

3. Insert the SIM card into the SIM card holder (7). Make sure that the SIM card is inserted properly

and that the golden contact area on the card is facing downwards.

Close the cover of the SIM card holder (8).

4. Replace the battery (9).

5. Direct the back cover towards the locking catches on the front cover (10) and slide the back cover

until it locks into its place (11).

■ Charging the battery

1. Connect the lead from the charger to the socket on the bottom

of your phone.

2. Connect the charger to an AC wall socket.

The text Charging is displayed briefly if the phone is switched

on. If the battery is completely flat, it may take a few minutes

before the charging indicator appears on the display or any

calls can be made.

You can use the phone while the charger is connected.

The charging time depends on the charger and the battery used. For example, charging a BLB-2 battery

with the ACP-7 charger takes about three hours.

■ Switching the phone on and off

Press and hold the power key

Note that if the phone displays Insert SIM even though the SIM card is properly

inserted, or SIM card not supported, contact your network operator or service

provider. Your phone does not support 5 Volt SIM cards and the card may need to be

changed.

• If the phone asks for a PIN code, key in the PIN code (displayed as ****), and press

OK.

See also PIN code request in Security settings on page 66 and Access codes on page 13.

• If the phone asks for a security code, key in the security code (displayed as *****), and press OK.

See also Access codes on page 13.

Warning: Do not switch the phone on when wireless phone use is prohibited or when it may cause

interference or danger.

TIPS ON EFFICIENT OPERATION: Your phone has a built-in antenna. As with any other

radio transmitting device, do not touch the antenna unnecessarily when the phone is

switched on. Contact with the antenna affects call quality and may cause the phone to

operate at a higher power level than otherwise needed. Not touching the antenna area

during a phone call optimises the antenna performance and the talktime of your phone.

■ Keypad lock (Keyguard)

You can lock the keypad to prevent the keys being accidentally pressed, for

example, when your phone is in your pocket or purse.

• Locking the keypad

In standby mode, press Menu and then

within 1.5 seconds to lock

the keypad.

• Unlocking the keypad

Press Unlock and then

within 1.5 seconds to unlock the keypad.

. During a call, the

To answer a call when the keyguard is on, press

phone can be operated normally. When you end or reject the call, the

keypad will automatically be locked.

Note: When Keyguard is on, calls may be possible to the emergency number programmed into your phone

(e.g. 112 or other official emergency number). Key in the emergency number and press

. The number

is displayed only after you have keyed in its last digit.

■ Changing the covers

Before changing the cover, always switch off the power and disconnect the phone from the charger or any other

device. Always store and use the phone with the covers attached.

1. Remove the back cover of the phone. With the back of the phone facing you, press the back cover

release button and slide the cover off the phone. See Installing the SIM card and the battery on

page 21.

2. Gently pull the phone off the front cover starting from the bottom

of the phone (1).

3. Replace the key mat on the new front cover (2).

4. To replace the front cover, align the top of the phone with the top

of the front cover (3) and gently push the phone towards the

cover (4). Ensure that the front cover is closed into place.

5. Replace the back cover of the phone. Direct the back cover

towards the locking catches on the front cover and slide the back

cover until it locks into place. See Installing the SIM card and the

battery on page 21.

3. Call functions

■ Making a call

1. Key in the phone number, including the area code. To delete a character to the left of the cursor,

press Clear.

For international calls, press

twice for the international prefix (the + character replaces the

international access code) and then key in the country code, area code and the phone number.

2. Press

3. Press

to call the number.

or End call to end the call or to cancel the call attempt.

When you are using the phone with the Plug-in Handsfree Car Kit, PPH-1, switch from handsfree mode

to privacy mode by disconnecting the PPH-1 from the phone. To switch back to handsfree, plug the

PPH-1 into the phone.

Making a call using the phone book

• See Searching for a name in the phone book on page 40. Press

to call the number on the

display.

Last number redialling

• In standby mode, press

once to access the list of the 20 numbers you last called or attempted

to call. Scroll to the number or name you want, and press

to call the number.

Calling your voice mailbox

• In standby mode, press and hold

, or press

and

If the phone asks for the voice mailbox number, key it in and press OK. See also Voice messages on

page 54.

Speed dialling a phone number

Assign a phone number to one of the speed dialling keys, from

, see Speed dialling on

page 43. Call the number in either of the following ways:

• Press the speed dialling key you want and then press

• If Speed dialling is set to on, press and hold a speed dialling key until the call is started. See Speed

dialling on page 61.

Making a conference call

Conference calling is a network service that allows up to six persons to take part in a conference call.

1. Make a call to the first participant.

2. To make a call to a new participant, press Options and select New call.

3. Key in, or retrieve from the memory, the phone number of the new participant and press Call. The

first call is put on hold.

4. When the new call has been answered, join the first participant in the conference call. Press

Options and select Conference.

5. To add a new participant to the call, repeat steps 2 to 4.

6. To have a private conversation with one of the participants:

Press Options and select Private. Scroll to the desired participant and press OK. Rejoin the

conference call, as described in step 4.

7. To end the conference call, press

■ Answering or rejecting an incoming call

Press

to answer the incoming call and press

to end the call.

Press

to reject the incoming call.

If you press Silence, only the ringing tone is muted. Then either answer or reject the call.

If the headset HDD-1 or HDC-5 is connected to the phone, you can answer and end a call by pressing

the headset key.

Tip: If the Divert if busy function is activated to divert the calls, for example to your voice

mailbox, rejecting an incoming call will also divert the call. See Call divert on page 60.

Call waiting

During a call, press

to answer the waiting call. The first call is put on hold. Press

to end the

active call.

To activate the Call waiting service function, see Call waiting service on page 61.

■ Options during a call

Many of the options that you can use during a call, are network services. Press Options during a call for

some of the following options:

Mute or Unmute, End call, End all calls, Phone book, Menu and Hold or Unhold, New call, Conference,

Private, Answer and Reject.

Send DTMF is used to send DTMF tone strings, for example, passwords or bank account numbers. Key in

the DTMF string or search for it in the phone book and press OK. Note that you can key in the wait

character w and the pause character p by repeatedly pressing

Swap is used to switch between the active call and the call on hold, Transfer to connect a call on hold

to an active call, and disconnect yourself from the calls, and Record to start the voice recording.

4. Writing text

You can key in text, for example when writing messages, in two different ways, using the traditional

method, or another method called predictive text input.

When you are writing text, the predictive text input is indicated by

and the traditional text input

at the top left of the display. The character case is indicated by Abc, abc, or ABC next to the text

input indicator, and you can change the character case by pressing

. The number mode is

indicated by 123, and you can change between the letter and number mode by pressing and holding

■ Setting predictive text input on or off

When writing text, press Options and select Dictionary.

• To set the predictive text input on, select a language in the dictionary options list. Predictive text

input is only available for the languages on the list.

• To change back to the traditional text input, select Dictionary off.

Tip: To quickly set the predictive text input on or off when writing text, press

twice, or

press and hold Options.

■ Using predictive text input

You can key in any letter with a single keypress. The predictive text input is based on a built-in

dictionary to which you can also add new words.

1. Start writing a word by using the keys

word changes after each keystroke.

. Press each key only once for one letter. The

For example, to write Nokia when the English dictionary is selected, press

once for o, once for k, once for i and once for a:

once for N,

To insert a number while in letter mode, press and hold the desired number key.

More instructions for writing text, see Tips for writing text on page 36.

2. When you have finished writing the word and it is correct, confirm it by pressing

or adding a

space with

If the word is not correct, you have the following options:

• Press

repeatedly until the word you want appears and confirm it.

• Press Options and select Matches.

If the ? character is displayed after the word, the word you intended to write is not in the dictionary.

To add the word to the dictionary, press Spell, key in the word (traditional text input is used) and

press Save. When the dictionary becomes full, the new word replaces the oldest one that was

added.

3. Start writing the next word.

Writing compound words

Key in the first part of the word and confirm it by pressing

. Write the last part of the word and

confirm it by pressing

■ Using traditional text input

Press a number key,

, repeatedly until the character you want appears. Not all

characters available under a number key are printed on the key. The characters available depend on the

language selected in the Language menu, see Language on page 62.

To insert a number while in letter mode, press and hold the desired number key.

• If the next letter you want is located on the same key as the present one, wait until the cursor

appears, or press

and then key in the letter.

•

The most common punctuation marks and special characters are available under the number key

More instructions for writing text, see Tips for writing text on page 36.

■ Tips for writing text

You can use also the following keys for writing text:

• To insert a space, press

• To move the cursor to the right or left, press

, respectively.

• To delete a character to the left of the cursor, press Clear. Press and hold Clear to delete the

characters more quickly.

• To insert a special character when using traditional text input, press

, or when using the

, and press to

predictive text input, press and hold

, or press Options and select Insert symbol.

Scroll through the list of characters and press Use to select a character.

To scroll through the list more quickly, press

select a character.

• To insert a number while in letter mode, press Options and select Insert number. Key in the numbers

you want and press OK.

• To insert a name or a phone number by searching for it in the phone book, press Options and select

Insert name or Insert number.

• To insert a word when using predictive text input, press Options and select Insert word. Write the

word using the traditional text input and press Save. The word is also added to the dictionary.

5. Phone book (Names)

You can save names and phone numbers in the phone’s memory (internal phone book) or in the SIM

card’s memory (SIM phone book).

• The internal phone book may save up to 500 names with numbers and textual notes for each name.

The total amount of names that can be saved depends on the length of the names, numbers and

text items.

• The phone supports SIM cards that can save up to 250 names and phone numbers. Names and

numbers saved in the SIM card’s memory, are indicated by

■ Selecting the phone book settings

1. Press Names and select Settings.

2. Select Memory in use, and select one of the following options:

Phone and SIM to recall names and numbers from both phone books. The names and numbers will

be saved in the phone’s memory.

Phone to use the internal phone book.

SIM card to use the SIM card’s phone book.

3. Select Phone book view and select one of the following options:

Name list to show three names at a time.

Name and no. to show one name and phone number at a time.

Large font to show only the name.

4. Select Memory status. Select Phone or SIM card to see how many names and phone numbers are

currently saved and how many can still be saved in the selected phone book.

■ Saving names and phone numbers (Add name)

Names and numbers will be saved in the used memory, see Selecting the phone book settings above.

1. Press Names and select Add name.

2. Key in the name and press OK. See Writing text on page 34.

3. Key in the phone number, and press OK. To key in the numbers, see Making a call on page 29.

4. When the name and number are saved, press Done.

Tip: Quick save

In standby mode, key in the phone number. Press Options, and select Save. Key in the name

and press OK.

Saving multiple numbers and text items per name

You can save up to five phone numbers and four brief text items in the phone’s internal phone book per

name. Text items relating to a name can be street and e-mail addresses, a note and a web address.

The first number saved under a name is automatically set as the default number and is indicated with

. When you select a name from the phone book, for example to make a call, the default number is

used unless you select another number.

1. Make sure that the memory in use is either Phone or Phone and SIM. See Selecting the phone book

settings on page 38.

2. To access the list of names and phone numbers, press

in standby mode.

3. Scroll to the name saved in the phone’s internal phone book to which you want to add a new

number or text item, and press Details.

4. Press Options and select Add number or Add text.

5. Select one of the following number or text types:

General is the default type used when no other number type is set as the default number. Other

number types are Mobile,

Home,

Office and

Fax.

Text types are E-mail,

Web addr.,

Postal addr. and

Note.

To change the number or text type, select Change type in the options list.

6. Key in the number or text item and press OK to save it.

7. Press Back and then Exit to return to standby mode.

Changing the default number

Press

in standby mode, scroll to the name you want and press Details. Scroll to the

number you want to set as the default number. Press Options and select Set as default.

■ Searching for a name in the phone book

1. Press Names and select Search.

2. Either press List to access the phone book or key in the first character(s) of the name you are

searching for and press Search. The matches with the pop-up window appear.

3. Scroll to the name you want, and press Details. Scroll to view the details of the selected name.

Tip: To quickly find a name and phone number, press

in standby mode. Key in the

first letter(s) of the name, and/or scroll to the name you want.

■ Editing a name, number or text item

Search for the name (and number) you want to edit and press Details. Scroll to the name, number or

text item you want to edit, and press Options. Select Edit name, Edit number, or Edit text, and edit the

name, number, or text and press OK.

■ Erasing names and numbers

Press Names and select Erase.

• To delete names and numbers one by one, select One by one and scroll to the name (and number)

you want to delete. Press Erase and press OK to confirm.

• To delete names and numbers in the phone book all at once, select Erase all and then scroll to the

phone book, Phone or SIM card and press Erase. Press OK and confirm with the security code.

■ Copying phone books

You can copy names and phone numbers from the phone’s memory to your SIM card’s memory and vice

versa.

1. Press Names and select Copy.

2. Select the copying direction, From phone to SIM card or From SIM card to phone.

3. Select One by one, All or Default nos..

• If you select One by one, scroll to the name you want to copy and press Copy.

Default nos. is shown if you copy from the phone to the SIM card. Only the default numbers will be

copied.

4. To select whether you want to keep or erase the original names and numbers, choose Keep original

or Move original.

• If you select All or Default nos., press OK when Start copying? or Start moving? is displayed.

■ Sending and receiving a business card

You can send and receive a person’s contact information as a business card either via IR or as an Over

The Air (OTA) message if supported by the network.

• Receiving a business card

Make sure that your phone is ready to receive data through its IR port, see Infrared (Menu 9) on

page 72. The user of the other phone can now send the name and phone number via Infrared.

When you have received a business card via IR or as an OTA message, press Show. Press Options and

select Save to save the business card in the phone’s memory, or Discard to discard the received

business card.

• Sending a business card

Using your phone’s infrared (IR) port, you can send a person’s contact info as a business card to a

compatible phone or other handheld device which supports the vCard standard.

1. Search for the name and phone number you want to send from the phone book, press Options

and select Send bus. card.

2. To send the business card via IR, make sure that the other phone or the PC is set up to receive

data via its IR port and select Via infrared.

To send the business card as an OTA message, select Via SMS.

■ Speed dialling

To make a call by using the speed dialling keys, see Speed dialling a phone number on page 31.

Assigning a number to a speed dialling key

Press Names and select Speed dials. Scroll to the speed dialling key number you want, and press

Assign. If a number is already assigned to the key, press Options, and you can view, change or erase

the assigned number.

Press Search, and select first the name and then the number you want to assign.

■ Voice dialling

You can make a phone call by saying a voice tag that has been added to a phone number. Any spoken

word(s), such as a person’s name(s), can be a voice tag.

Before using voice dialling, note that:

•

Voice tags are not language dependent. They are dependent on the speaker's voice.

Voice tags are sensitive to background noise. Record them and make calls in a quiet environment.

When recording a voice tag or making a call by saying a voice tag, hold the phone in the normal position near to

your ear.

•

Very short names are not accepted. Use long names and avoid similar names for different numbers.

Note: You must say the name exactly as you said it when you recorded it. This may be difficult in, for

example, a noisy environment or during an emergency, so you should not rely solely upon voice dialling in

all circumstances.

Adding a voice tag

Save or copy in the phone’s memory the names and phone numbers, to which you want to add a voice

tag. You can add up to ten voice tags.

You can also add voice tags to the names in the SIM card, but if you replace your SIM card with a new

one, you first need to delete the old voice tags before you can add new ones.

1. In standby mode, press

2. Scroll to the name to which you want to add a voice tag and press Details. Scroll to the phone

number you want and press Options.

3. Select Add voice tag.

4. Press Start, and say clearly the word(s) you want to record as a voice tag. After recording, the phone

plays the recorded tag.

5. When the voice tag has been successfully saved, Voice tag saved is displayed, a beep sounds and a

symbol

appears after the phone number with a voice tag.

Making a call by using a voice tag

When an application using the GPRS connection is sending or receiving data, you cannot make a call

by using voice dialling. To make a call by using a voice tag, end the application using the GPRS

connection.

1. In standby mode, press and hold the volume down key, or press and hold Names. A short tone is

heard and Speak now is displayed.

2. Say the voice tag clearly.

3. The phone plays the recognised voice tag and then dials the phone number of the voice tag after 1.5

seconds.

If you are using the headset HDD-1 or HDC-5, press and hold the headset key to start the voice dialling.

Replaying, changing or erasing a voice tag

Press Names and select Voice tags. Scroll to the name with the voice tag you want, press Options and

you can listen to, erase or change the recorded voice tags.

■ Service numbers

You can call the service numbers of your service provider if the numbers are included on your SIM card.

Press Names and select Service nos.. Scroll to a service number and press

to call the number.

■ Caller groups

You can arrange the names and phone numbers saved in the phone book into caller groups. For each

caller group, you can set the phone to sound a specific ringing tone and show a selected graphic on the

display when you receive a call from a phone number in the group, see below. To set the phone to ring

only upon calls from phone numbers belonging to a selected caller group, see Alert for in Tone settings

on page 64.

Press Names, select Caller groups and select the caller group you want. Select

•

Group name, key in a new name for the caller group and press OK.

Group ringing tone and select the ringing tone you want to set for the group. Default is the ringing

tone selected for the currently active profile.

•

Group logo and select On to set the phone to display the group logo, Off not to display it, View to

view the logo, or Send logo to send the logo as an Over The Air (OTA) message if supported by your

network.

Group members. To add a name to the caller group, (press Options and) select Add name. Scroll to

the name you want to add to the group and press Add.

To remove a name from a caller group, scroll to the name you want to remove, and press Options

and select Remove name.

6. Using the menu

The phone offers you an extensive range of functions which are grouped in menus. Most of the menu

functions are provided with a brief help text. To view the help text, scroll to the menu function you

want and wait for 15 seconds. To exit the help text, press Back. See Help text activation on page 63.

■ Accessing a menu function

By scrolling

1. To access the menu, press Menu.

2. Scroll through the menu and select, for example, Settings by pressing Select.

3. If the menu contains submenus, select the one you want, for example Call settings.

4. If the selected submenu contains further submenus, repeat step 3. Select the next submenu, for

example Anykey answer.

5. Select the setting of your choice.

6. Press Back to return to the previous menu level, and Exit to exit the menu.

By shortcut

The menus, submenus and setting options are numbered and you can access them by using their

shortcut number. The shortcut number is shown in the top right corner of the display.

• To access the menu, press Menu. Key in quickly, within two seconds, the index number of the menu

function you want to access.

For example, to set the Anykey answer On, press Menu,

and

■ List of menu functions

1. Messages

3. Profiles

1. Write message

2. Inbox

1. General

2. Silent

3. Outbox

3. Meeting

4. Archive

4. Outdoor

5. Templates

5. Pager

6. My folders

4. Settings

7. Erase messages

8. Voice messages

9. Info messages

10.Service command editor

11.Message settings

2. Call register

1. Missed calls

1. Alarm clock

2. Time settings

3. Call settings

4. Phone settings

5. Tone settings

6. Accessory settings

7. GPRS modem settings

8. Security settings

9. Restore factory settings

5. Games

2. Received calls

3. Dialled numbers

4. Erase recent call lists

5. Call duration

6. Call costs

1. Select game

2. Game services

3. Settings

7. GPRS data counter

8. GPRS connection timer

6. Calculator

7. To-do list

8. Calendar

9. Infrared

10.Radio

4. Stopwatch

12.Services

1. Home

2. Bookmarks

3. Service inbox

4. Settings

11. Extras

1. Voice recorder

2. Voice commands

3. Countdown timer

5. Go to address

6. Clear the cache

13.SIM services¹

1. Only shown if supported by your SIM card. The name and contents vary depending on the SIM card

7. Menu functions

■ Messages (Menu 1)

You can read, write and send text and picture messages or save your messages. All

the messages in your phone’s message memory are organised in folders.

Before you can send any text or picture messages, you need to save your message centre number, see

Message settings on page 55.

Writing and sending messages

You can write and edit text messages of up to 160 characters.

1. Press Menu, select Messages and Write message

2. Key in a message. See Writing text on page 34.

See also Inserting a text template or a picture into a message on page 52.

3. To send the message, press Options, and select Send.

4. Enter the recipient’s phone number or search for the phone number in the phone book.

Press OK to send the message.

Note: When sending messages via the SMS network service, your phone may display the words "Message

sent". This is an indication that the message has been sent by your phone to the message centre number

programmed into your phone. This is not an indication that the message has been received at the

intended destination. For more details about SMS services, check with your service provider.

Options for sending a message

After you have written a message, press Options, and select Sending opt’s.

• To send a message to several recipients, select Send to many. When you have sent the message to

everyone you want to send it to, press Done.

• To send a message using a message profile, select Sending profile and then the message profile you

want to use.

For example, if you select a profile you have defined as an e-mail transmission, key in or search the

phone book for the recipient’s e-mail address and press OK. Key in the e-mail service number, select

Accept to send the message.

To define a message profile, see Message settings on page 55.

Text and picture templates

Press Menu, select Messages and Templates. The list of text templates, indicated with

templates, indicated with , is displayed.

, and picture

Your phone offers you 10 picture message templates. You can also save new pictures into the

Templates folder. More pictures can be found on the Nokia website, http://www.club.nokia.com.

Note: This function can be used only if it is supported by your network operator or service provider. Only

phones that offer picture message features can receive and display picture messages.

• Each picture message is made up of several text messages. Therefore, sending one picture message

may cost more than sending one text message.

• Since picture messages are saved in the phone’s memory, you cannot view them if you use your SIM

card with another phone.

Inserting a text template or a picture into a message

When you are writing or replying to a message, press Options.

• Select Use template and select the template you want to insert.

• When you are writing or replying to a message, press Options. Select Attach picture and select a

picture to view it. Press Attach to insert the picture into your message. The

indicator on the

header of the message indicates that a picture has been attached. The number of characters that

you can enter in a message, depends on the size of the picture.

To view the text and the picture together before sending the message, press Options and select

Preview.

Reading and replying to a message

When you have received a message, the indicator

and the number of new messages followed by

message(s) received will appear on the display.

The blinking

indicates that the message memory is full. Before you can receive or send new

messages, delete some of your old messages.

1. Press Show to view the message, or press Exit to view it later.

Reading the message later: Press Menu, select Messages and Inbox.

2. If more than one message is received, select the message you want to read. An unread text message

is indicated by

in front of it and an unviewed picture message is indicated by

3. While reading or viewing the message, press Options.

You can select an option to erase, forward, edit, move, and rename the message you are reading.

You can also change the font size of the message. Select Copy to calend. to copy the message to

your phone’s calendar as a reminder note for the current day.

Select Details to view, for example, the sender’s name and phone number, the message centre used,

reception date and time.

Select Use number to extract numbers from the current message.

Select Save picture to save the picture in the Templates folder.

Select Reply to reply to a message. Select Original text to include the original message in the reply,

or select standard answers, for example, Thank you or Congrats or Template to be included in the

reply, or select Empty screen.

4. Write your reply message.

5. Press Options, select Send, and press OK to send the message to the displayed number.

Inbox and outbox folders

After you have read an incoming text or picture message, the phone saves the message in the Inbox

folder of the Messages menu.

The messages you have saved to be sent later, are saved in the Outbox folder.

Erasing the messages

Press Menu, select Messages and select Erase messages.

To delete all the messages in a folder, scroll to the folder and press OK. Then press OK when Erase all

read messages from folder? is displayed.

To delete all read messages from all the folders, scroll to All read and press OK . Then press OK when

Erase read messages from all folders? is displayed.

Archive folder and my folders

To organise your messages, you can move some of your messages to the Archive folder, or add new

folders for your messages.

While reading a message, press Options. Select Move, scroll to the folder where you want to move the

message and press OK.

To add or delete a folder, press Menu, select Messages and My folders.

• To add a folder, press Options and select Add folder.

• To delete a folder, scroll to the folder you want to delete, press Options and select Delete folder.

Voice messages

Voice mailbox is a network service and you may need to subscribe to it first. For more information and

for the voice mailbox number, contact your service provider.

Press Menu, select Messages and Voice messages. Select

•

Listen to voice messages to call your voice mailbox at the phone number you have saved within the

Voice mailbox number menu.

Each phone line may have its own voice mailbox number, see Line for outgoing calls on page 62.

•

Voice mailbox number to key in, search for or edit your voice mailbox number and press OK to save

it.

If supported by the network, the indicator

your voice mailbox number.

will indicate new voice messages. Press Listen to call

Info messages

With the info message network service you can receive messages on various topics, for example

weather or traffic conditions, from your service provider. For available topics and relevant topic

numbers, contact your service provider.

If the GPRS connection is set to Always online, the info messages may not be received. In that case, set

the GPRS connection to When needed, see Setting up the phone for a WAP service on page 80.

Service command editor

Press Menu, select Messages and Service command editor. Key in and send service requests (also

known as USSD commands) such as activation commands for network services, to your service

provider.

Message settings

The message settings affect the sending of the messages.

Press Menu, select Messages and Message settings.

If more than one message profile set is supported by your SIM card, select the set you want to change.

Select Message centre number to save the phone number of the message centre. You need the message

centre number to send text and picture messages. You receive the number from your service provider.

Select Messages sent as to select the message format, or Message validity. Select Default recipient

number to save a default number to send messages for this message profile, Delivery reports to request

the network to send delivery reports on your messages (network service), and Use GPRS to set GPRS as

the preferred SMS bearer. Select Reply via same centre to allow the recipient of your message to send

you a reply message via your message centre (network service), and Rename sending profile to change

the name of the selected message profile. The message profile sets are displayed only if your SIM card

supports more than one set.

■ Call register (Menu 2)

The phone registers the phone numbers of missed, received and dialled calls, and the

approximate length and cost of your calls.

The phone registers missed and received calls only if the network supports these functions, the phone

is switched on and within the network’s service area.

When you press Options in the Missed calls, Received calls and Dialled numbers menu, you can view

the date and the time of the call, edit or erase the phone number from the list, save the number in the

phone book, or send a message to the number.

Recent calls lists

Press Menu, select Call register and then select

•

Missed calls to view the list of the last ten phone numbers from which somebody has tried to call

you (network service).

Tip: When a note about missed calls is being displayed, press List to access the list of phone

numbers. Scroll to the number you would like to call back and press

•

Received calls to view the list of the last ten phone numbers from which you have most recently

accepted calls (network service).

Dialled numbers to view the list of the 20 phone numbers that you have most recently called or

attempted to call. See also Last number redialling on page 29.

Erase recent call lists to erase the recent calls lists. Select whether you want to delete all the phone

numbers in the recent call lists, or only those numbers in the missed calls, received calls or dialled

numbers lists. You cannot undo the operation.

Call counters and call timers

Note: The actual invoice for calls and services from your service provider may vary, depending upon

network features, rounding-off for billing, taxes and so forth.

Press Menu, select Call register and then select

•

Call duration, scroll to view the approximate duration of your incoming and outgoing calls in hours,

minutes and seconds. To clear the timers, the security code is needed.

Each phone line has its own call timers and the timers of the selected line are displayed. See Line for

outgoing calls on page 62.

•

Call costs (network service). Select Last call units or All calls’ units to check the cost of your last call

or all calls.

Select Call cost settings and then select Clear counters, or select Show costs in to set the phone to

show the remaining talk time in terms of charging units, Units, or units of currency, Currency.

Contact your service provider for charging unit prices. Select Call cost limit to limit the cost of your

calls to a certain amount of charging units or units of currency. The PIN2 code is needed for the call

cost settings.

Note: When no more charging units or currency units are left, calls may only be possible to the

emergency number programmed into your phone (e.g. 112 or other official emergency number).

•

GPRS data counter and scroll to check the amounts of last sent and last received data, data sent

and received in total, and to clear the counters. The counters unit is a byte.

GPRS connection timer and scroll to check the duration of the last GPRS connection or the total

GPRS connection. You can also clear the timers.

■ Profiles (Menu 3)

Your phone has various setting groups, profiles, for which you can customise the

phone tones for different events and environments. At first, personalise the profiles

to your liking and then you only need to activate a profile to use it.

Available profiles are General, Silent, Meeting, Outdoor, and Pager.

Press Menu and select Profiles. Scroll to a profile and press Select.

• To activate the profile, select Activate.

Tip: To change the profile quickly in standby mode, press the power key

, scroll to the

profile you want to activate and press Select.

• To set the profile to be active for a certain amount of time up to 24 hours, select Timed and set the

time. When the time set for the profile expires, the previous profile that was not timed, becomes

active.

• To personalise the profile, select Personalise. Select the setting you want to change and make the

changes.

The settings can also be changed in the Tone settings menu, see Tone settings on page 64.

In addition you can rename a profile, Profile name. The General profile can not be renamed.

■ Settings (Menu 4)

Alarm clock

The alarm clock uses the time format set for the clock. The alarm clock works even when the phone is

switched off.

Press Menu, select Settings and Alarm clock. Key in the alarm time and press OK. To change the time

when the alarm time is set, select On.

When the alarm time expires

The phone will sound an alert tone, and flash Alarm! and the alarm time on the display.

Press Stop to stop the alarm. If you let the phone continue to alarm for a minute or press Snooze, the

alarm stops for a few minutes and then resumes.

If the alarm time is reached while the phone is switched off, the phone switches itself on and starts sounding the

alarm tone. If you press Stop, the phone asks whether you want to activate the phone for calls, Switch the phone

on?. Press No to switch off the phone or Yes to make and receive calls.

Note: Do not press Yes when wireless phone use is prohibited or when it may cause interference or danger.

Time settings

Clock

Press Menu, select Settings, Time settings and Clock.

Select Show clock and the time is shown on the top right of the display when the phone is in standby

mode. Select Set the time, to adjust the clock to the right time, and Time format to select the 12-hour

or 24-hour time format.

The clock also serves the functions Messages, Call register, Alarm clock, timed Profiles and Calendar.

If the battery is removed from the phone for a long time, you may need to set the time again.

Auto update of date and time

Press Menu, select Settings, Time settings and Auto update of date and time (network service). To set

the phone to automatically update the time and date according to the current time zone, select On. To

set the phone to ask for a confirmation before the update, select Confirm first.

Updating the date and time affects the alarm clock, calendar and voice recorder, and the alarm notes

you have set are now set to the local time. Updating may cause some calendar notes to expire.

Call settings

Call divert

Press Menu, select Settings, Call settings and Call divert (network service). With call divert you can

direct your incoming calls to another number, for example, to your voice mailbox number. For details,

contact your service provider. Divert options not supported by your SIM card or your network operator

may not be shown.

Select the divert option you want, for example, select Divert if busy to divert the voice calls when your

number is busy or when you reject an incoming call.

To set the divert setting to on, select Activate, to set the divert setting to off, select Cancel, or Check

status to check whether the divert is activated or not. To change the timeout when the call is diverted,

first select Set delay if this is available for the divert option, and then select Activate to set the divert

setting to on. Several divert options may be active at the same time.

To see the divert indicators in standby mode, see Standby mode on page 19.

Anykey answer

Press Menu, select Settings, Call settings and then Anykey answer. Select On and you can answer an

incoming call by briefly pressing any key, except

, selection keys

and

, and

Automatic redial

Press Menu, select Settings, Call settings and Automatic redial. Select On and your phone will make a

maximum of ten attempts to connect the call after an unsuccessful call attempt.

Speed dialling

Press Menu, select Settings, Call settings and Speed dialling. Select On and the names and phone

numbers assigned to the speed dialling keys, from

, can be dialled by pressing and

holding the corresponding number key.

Call waiting service

Press Menu, select Settings, Call settings and Call waiting service. Select Activate and the network will

notify you of an incoming call while you have a call in progress (network service). See Call waiting on

page 32.

Summary after call

Press Menu, select Settings, Call settings and Summary after call. Select On and the phone will briefly

display the duration and cost (network service) of the last call.

My number sending

Press Menu, select Settings, Call settings and My number sending. Select On and your phone number

will be displayed to the person you are calling (network service). Select Set by network and the setting

agreed upon with your service provider is used.

Line for outgoing calls

Line for outgoing calls is a network service to select the phone line 1 or 2, that is subscriber number, for

making calls.

Press Menu, select Settings, Call settings and Line for outgoing calls. If you select Line 2 and have not

subscribed to this network service, you will not be able to make calls. However, calls on both lines can

be answered regardless of the selected line.

If supported by your SIM card, you can prevent the line selection by selecting the option Lock.

For more information on availability, contact your network operator or service provider.

Tip: In standby mode you can switch from one line to the other by pressing and holding

Phone settings

Language

Press Menu, select Settings, Phone settings and Language. Select the language for the display texts. If

Automatic is selected, the phone selects the language according to the information on the SIM card.

Cell info display

Press Menu, select Settings, Phone settings and Cell info display. Select On to set the phone to indicate

when it is used in a cellular network based on Micro Cellular Network (MCN) technology.

If the GPRS connection is set to Always online, the info messages may not be received. In that case, set

the GPRS connection to When needed, see Setting up the phone for a WAP service on page 80.

Welcome note

Press Menu, select Settings, Phone settings and Welcome note. Key in the note you would like to be

shown briefly when the phone is switched on. To save the note, press Options, and select Save.

Network selection

Press Menu, select Settings, Phone settings and Network selection. Select Automatic and the phone

automatically selects one of the cellular networks available in your area.

If you select Manual, you can select a network that has a roaming agreement with your home network

operator. Otherwise, No access will be displayed and you must select another network. The phone stays

in manual mode until the automatic mode is selected or another SIM card is inserted into the phone.

Confirm SIM service actions

See SIM services (Menu 13) on page 91.

Help text activation

To set the phone to show or not to show the help texts, press Menu, select Settings, Phone settings and

Help text activation.

See also Using the menu on page 47.

Start-up tone

To set the phone to play or not to play a start-up tone when the phone is switched on, press Menu,

select Settings, Phone settings and Start-up tone.

If you have set a welcome note, the start-up tone will not be played, see Welcome note on page 63.

Tone settings

Press Menu, select Settings and then Tone settings. You can find the same settings in the Profiles

menu, see Profiles (Menu 3) on page 58.

Select Incoming call alert to select how the phone notifies you of an incoming voice call. The options

are Ringing, Ascending, Ring once, Beep once and Off.

Select Ringing tone, Ringing volume and Vibrating alert for an incoming voice call and an incoming

message. The vibrating alert does not work when the phone is connected to a charger, desktop stand,

or a car kit.

Tip: If you receive a ringing tone via IR or OTA, you can save five ringing tones at a time in the

ringing tone list.

Select Message alert tone to set the alert tone for the incoming messages, Keypad tones, or Warning

tones to set the phone to sound tones for example, when the battery is running out of power.

Select Alert for to set the phone to ring only upon calls from phone numbers that belong to a selected

caller group. Scroll to the caller group you want or All calls and press Mark.

Accessory settings

Accessory settings menu is shown only if the phone is or has been connected to one of the following

accessories: headsets HDC-5, HDE-2 or HDD-1, handsfree car kit PPH-1, or mobile inductive loopset

LPS-3.

Press Menu, select Settings and Accessory settings. Select Headset, Handsfree or Loopset.

• Select Default profile to select the profile you want to be automatically activated when you

connect the selected accessory. You can select another profile while the accessory is connected.

• Select Automatic answer to set the phone to answer an incoming call automatically after five

seconds. If the Incoming call alert is set to Beep once or Off, automatic answer will not be in use.

• Select Lights to set the lights permanently on, On. Select Automatic to set the lights on for 15

seconds after a keypress. The Lights option is available only when Handsfree is selected.

• Select Use loopset to set the loopset in use instead of the headset, Yes. Use loopset is available only

when Loopset is selected.

GPRS modem settings

You can connect the phone via infrared connection to a compatible PC and use the phone as a modem

to enable GPRS connectivity from the PC.

Press Menu, select Settings and GPRS modem settings. Select Active access point and activate the

access point you want to use. Select Edit active access point to change the access point settings.

• Scroll to Alias for access point and press Rename. Key in the name you would like for the activated

access point and press OK.

• Scroll to GPRS access point and press Edit. Key in the Access Point Name (APN) and press OK.

An access point name is needed to establish a connection to a GPRS network. You can obtain the

Access Point Name from your network operator or service provider.

You can also set the GPRS dial-up service settings (Access Point Name) on your PC by using the Nokia

Modem Options software, see Modem setup on page 94. If you have set the settings on your PC and

your phone, note that the settings set on the PC will be used.

Security settings

Note: When security features that restrict calls are in use (call barring, closed user group and fixed

dialling), calls may be possible to certain emergency numbers in some networks (e.g. 112 or other official

emergency numbers).

Press Menu, select Settings and Security settings. Select

•

PIN code request to set the phone to ask for your PIN code every time the phone is switched on.

Some SIM cards do not allow the PIN code request to be turned off.

Call barring service (network service) to restrict incoming calls to and outgoing calls from your

phone. A barring password is required.

Fixed dialling to restrict your outgoing calls to selected phone numbers if this function is supported

by your SIM card. The PIN2 code is required.

Closed user group. Closed user group is a network service that specifies the group of people whom

you can call and who can call you. For more information contact your network operator or service

provider.

•

Security level. Select Phone and the phone will ask for the security code whenever a new SIM card is

inserted into the phone.

Select Memory and the phone will ask for the security code when SIM card’s memory is selected

and you want to change the memory in use, see Selecting the phone book settings on page 38 or

copy from one memory to another, Copying phone books on page 41.

•

Change of access codes and you can change the security code, PIN code, PIN2 code or barring

password. Codes can only include numbers from 0 to 9.

Note that you should avoid using access codes similar to the emergency numbers, such as 112, to

prevent accidental dialling of the emergency number.

Restore factory settings

To reset some of the menu settings to their original values, press Menu, select Settings and Restore

factory settings. Key in the security code and press OK. For example, the names and phone numbers

saved in the phone book are not deleted.

■ Games (Menu 5)

Note: Your phone must be switched on to use this function. Do not switch the phone

on when wireless phone use is prohibited or when it may cause interference or danger.

Starting a game and game options

Press Menu, select Games and Select game. Select the game you would like to play, Snake II, Bumper or

Pairs II. If available for the game, select the game type or 1 player or 2 players.

• You may play some games as a 2-player game via the IR port of your phone with a person who has

the same game on a compatible phone. Before starting a 2-player game, ensure that the IR ports of

the two phones are pointing at each other. See Infrared (Menu 9) on page 72.

Select one of the options that may be available for the game:

•

Continue to continue a paused game. To pause a game, press

New game to start a new game session in 1-player games.

Host game to start a game against another person in 2-player game.

Join game to join a game in 2-player game.

or either of the selection keys.

Options to change the settings for the selected game.

Level to set the level of difficulty for the selected game.

High scores to view the highest scores.

Instructions to select a help text on how to play the game.

Game services and game settings

Press Menu, and select Games. Select

•

Game services and the phone tries to connect to the WAP pages of Club Nokia by using the

currently active set of service settings.

If the connection fails, you may not be able to access Club Nokia from the WAP service whose

connection settings are currently active. In this case, enter the Services menu, activate another set

of service settings, see Making a connection to a WAP service on page 83. Try again to connect to

Club Nokia.

For the availability of different WAP services, pricing and tariffs, contact your network operator

and/or the WAP service provider.

•

Settings to set sounds, lights and vibrator, Shakes, for the game. The vibrator can be set on only if

Vibrating alert is set on, see Tone settings on page 64. You can save your Club Nokia membership

number, Club Nokia ID. For more information on Club Nokia and the game services, visit

www.club.nokia.com. Availability may vary by country.

■ Calculator (Menu 6)

The calculator in your phone adds, subtracts, multiplies, divides, counts the square and

the square root and converts currency values.

Note: Your phone must be switched on to use this function. Do not switch the phone on when wireless

phone use is prohibited or when it may cause interference or danger.

This calculator has a limited accuracy and rounding errors may occur, especially in long divisions.

1. Press Menu and select Calculator.

2. When ’0’ is displayed on the screen, key in the first number in the calculation, press

for a

decimal point.

3. Press Options and select Add, Subtract, Multiply, Divide, Square, Square root or Change sign.

Tip: Alternatively, press

once to add, twice to subtract, three times to multiply or four

times to divide.

4. Key in the second number.

5. For a total, press Options and select Equals. Repeat steps 3 to 5 as many times as is necessary.

6. To start a new calculation, first press and hold Clear.

Making a currency conversion

1. Press Menu and select Calculator.

2. To save the exchange rate, press Options and select Exchange rate. Select either of the displayed

options. Key in the exchange rate, press for a decimal point, and press OK. The exchange rate

remains in the memory until you replace it with another one.

3. To make the currency conversion, key in the amount to be converted, press Options and select In

domestic or In foreign.

You can also make the currency conversion in standby mode. Key in the amount to be converted, press

Options and select In domestic or In foreign.

■ To-do list (Menu 7)

You can save a note for a task that you have to do. The notes can be saved in priority

order. You may be able to save up to 30 notes but this depends on how long the

notes are.

Press Menu and select To-do list. Press Options, or scroll to the note you want and then press Options.

• Select Add to add a new note. Key in the subject for the note, press Options and select Save. Select

the priority for the note, High (1), Medium (2), or Low (3). The notes are listed first in priority order

and then in alphabetical order.

Dictionary, refer to Setting predictive text input on or off on page 34.

• You can also erase, edit, view the selected note, or edit the priority level of the selected note, and

you can select the priority level from which you like to view notes, save the note as a calendar note

or send the note to another phone as a text message.

■ Calendar (Menu 8)

The calendar helps you to keep track of reminders, calls that you need to make,

meetings, and birthdays.

Note: Your phone must be switched on to use this function. Do not switch the phone on when wireless

phone use is prohibited or when it may cause interference or danger.

Press Menu and select Calendar. Scroll to the day you want. If there are any notes set for the day, the

corresponding note type indicator is shown.

Day view and note view

• Press Options and select Day notes. The day view lists the notes made for the day. The note

indicator is shown first on the line.

• When in the Day view, scroll to the note you want to view. Press Options and select View.

The note view allows you to view the details of the selected note. You can scroll through the note.

The other options for the calendar views may include:

• Options for making a note, for sending a note via IR, or as a note directly to another phone’s

calendar or as a text message.

• Options for erasing, editing, moving and repeating a note and for copying a note to another day.

•

Settings to set, for example, the date, time, date format or time format. In the Auto erase option

you can set the phone to delete old notes automatically after a specified time. However, the repeat

notes, for example, birthday notes, will not be deleted.

Making a calendar note

For keying in letters and numbers, see Writing text on page 34.

Press Menu and select Calendar. Scroll to the date you want, press Options and select Make a note.

Select one of the following note types:

•

Meeting - Key in the note, or search for the name in the phone book, and press OK. Then key in

the time for the meeting and press OK. If you wish, select Alarm on and then the alarm time for the

note.

Call - Key in the phone number you want, press OK, and key in the name and press OK, or

search for them in the phone book. Then key in the time for the call and press OK. If you wish, select

Alarm on and then the alarm time for the note.

Birthday - Key in the persons name (or search for it in the phone book), and press OK. Then key

in the date of birth, and press OK. Key in the year of birth (optional), and press OK. If you key in the

year, the note shows you the person’s age after the name. If you wish, select Alarm on and then the

alarm time for the note.

•

Memo - Key in the note, and press OK.

When a tone alert is set, the indicator

is displayed when you view the notes.

When the phone alarms for a note

The phone beeps, and displays the note. With a call note

on the display, you can call the displayed

number by pressing . To stop the alarm and view the note, press View. To stop the alarm without

viewing the note, press Exit.

■ Infrared (Menu 9)

You can set up the phone to receive data through its infrared (IR) port. To use an IR

connection, the device with which you want to establish a connection must be IrDA

compliant. You can send or receive data such as business cards and calendar notes to or from a

compatible phone or data device (for example, a computer) via the IR port of your phone.

Do not point the IR (infrared) beam at anyone’s eye or allow it to interfere with other IR devices. This device is a

Class 1 Laser product.

Note: Your phone must be switched on to use this function. Do not switch the phone on when wireless

phone use is prohibited or when it may cause interference or danger.

Sending and receiving data via IR

• Ensure that the IR ports of the sending and receiving devices are pointing at each other and that

there are no obstructions between the devices. The preferable distance between the two devices in

an infrared connection is one meter at most.

• To activate the IR port of your phone to receive data via IR, press Menu and select Infrared.

• The user of the sending phone selects the desired IR function to start data transfer.

If data transfer is not started within two minutes after the activation of the IR port, the connection is

cancelled and has to be started again.

IR connection indicator

• When

is shown continuously, the IR connection is activated and your phone is ready to send or

receive data via its IR port.

• When

blinks, your phone is trying to connect to the other device or a connection has been lost.

■ Radio (Menu 10)

Note: Your phone must be switched on to use this function. Do not switch the phone

on when wireless phone use is prohibited or when it may cause interference or danger.

You can listen to the FM radio on your phone only by using the headsets HDD-1, HDC-5 or HDE-2.

Connect the headset to the headset connector on the bottom of the phone. The lead of the headset

functions as the antenna of the radio, so let it hang freely.

Note that the quality of the radio broadcast depends on the radio station’s coverage in that particular

area.

1. To turn on the radio, press Menu and select Radio. On the display are

• Channel location number and the name of the radio channel.

• Frequency of the radio channel.

2. If you have already saved radio channels, you can scroll to the channel you would like to listen to, or

select a radio channel location 1 to 9 by pressing the corresponding number key.

When using the headset HDD-1 or HDC-5, press the headset key to select a radio channel.

3. When the radio is on, press Options and select Switch off to turn off the radio.

Tip: To quickly turn off the radio, press and hold

Tuning a radio channel

When the radio is on, press and hold

to start the channel search. Searching stops when a

channel is found. To save the channel, press Options, and select Save channel. Key in the name of the

channel and press OK. Select the location where you want to save the channel.

Tip: To quickly save the channel in a location 1 to 9, press and hold the corresponding number

key, then key in the name of the channel and press OK.

Using the radio

When the radio is on, press Options and select

•

Switch off to turn off the radio.

Save channel to save the radio channel you have found, refer to Tuning a radio channel above. Up to

20 radio channels can be saved.

•

Auto tuning. Briefly press either of the scroll keys to start the channel search upwards or

downwards. The search stops when a channel has been found, press OK. To save the channel, see

Save channel above.

Set frequency. If you know the frequency of the radio channel you would like to listen to (between

87.5 MHz and 108.0 MHz), key it in and press OK. To save the channel, see Save channel above.

Tip: To quickly select Set frequency, press

when in the Radio menu.

•

Rename. Key in a new name for the saved channel and press OK.

Manual tuning. Briefly press either of the scroll keys to move the channel search 0.1 MHz upwards

or downwards or press and hold down for searching the channel fast upwards or downwards. To

save the found channel, press OK and see Save channel above.

Tip: To quickly select Manual tuning, press

when in the Radio menu.

You can normally answer an incoming call while listening to the radio. The volume of the radio is

muted. When you end the call, the radio will automatically be turned on.

When an application using a GPRS or HSCSD connection is sending or receiving data, it may interfere

with the radio.

■ Extras (Menu 11)

Note: Your phone must be switched on to use the functions in Extras menu. Do not

switch the phone on when wireless phone use is prohibited or when it may cause interference or danger.

Voice recorder

You can record pieces of speech, sound or an active call for three minutes. For example, this is useful

when recording a name and phone number for writing them down later.

Note: Obey all local laws governing recording of calls. Do not use this feature illegally.

Recording

1. Press Menu, select Extras and Voice recorder.

2. To start the recording, select Record. To start the recording during a call, press Options, and select

Record. While recording a call, all parties to the call will hear a faint beep sound approximately

every five seconds.

When recording, hold the phone in the normal position near to your ear.

3. To end the recording, press Stop.

4. Key in a new name for the recording and press OK to save it.

If you do not want to save the recording, press Clear to erase the preset name. Then press Back and

OK.

If you record an active call, the phone automatically saves the recording by name Recording.

List of recordings

Press Menu, select Extras and Voice recorder. Select Recordings list, scroll to the recording you want

and press Options.

• Select Playback to listen to the selected recording.

• Select Edit title. Key in a new name for the recording and press OK.

• Select Erase to erase the recording. Press OK to confirm.

• Select Add alarm. Key in the date for the alarm and press OK. Key in the time for the alarm and press

OK.

Alarm replaces Add alarm when the alarm is set on. Select Alarm and the name of the recording, the

date and the time for the alarm are displayed. To remove the alarm, press Erase and then press OK.

When the alarm time expires, the phone will sound an alert tone, Recording! and the alarm time and

the name of the recording are displayed. Press Stop to stop the alarm, and then press Play to play the

recording.

Voice commands

You have a list of phone functions which can be activated by saying a voice tag. Up to five voice tags

for the voice commands can be added.

Press Menu, select Extras and Voice commands. Select the command folder you want, scroll to the

command to which you want to add a voice tag and press Options. If the command already has a voice

tag, the indicator

is shown.

To add a voice command, refer to Adding a voice tag on page 44. See also Replaying, changing or

erasing a voice tag on page 45.

To activate a voice command, refer to Making a call by using a voice tag on page 44.

When an application using the GPRS connection is sending or receiving data, you cannot activate a

voice command. To activate a voice command, end the application using the GPRS connection.

Countdown timer

Press Menu, select Extras and Countdown timer. Key in the alarm time in hours and minutes and press

OK. If you wish, write your own note text which is displayed when the time expires, and press OK to

start the countdown timer.

• To change the countdown time, select Change time, or to stop the timer, select Stop timer.

If the alarm time is reached when the phone is in standby mode, the phone sounds a tone and flashes

the note text if it is set or else Countdown time up. Stop the alarm by pressing any key. If no key is

pressed, the alarm automatically stops within 30 seconds. To stop the alarm and to erase the note text,

press OK.

Stopwatch

You can measure time, take intermediate times or lap times using the stopwatch. During timing, the

other functions of the phone can be used. To set the timing in the background, press

Using the stopwatch consumes the battery and the phone’s operating time will be reduced. Be careful not to let it

run in the background when performing other operations with your phone.

Time observation and time splitting

1. Press Menu, select Extras, Stopwatch and Split timing.

You can select Continue if you have set the timing in the background.

2. Press Start to start the time observation. Press Split every time you want to take an intermediate

time. The intermediate times are listed below the running time on the display. Scroll to view the

times.

3. Press Stop to stop the time observation.

4. Press Options and select

Start to start the time observation again. The new time is added to the previous time.

Save to save the time. Key in a name for the measured time and press OK. If no name is keyed in, the

total time is used as a title.

Reset to reset the time without saving it.

Lap times

Press Menu, select Extras, Stopwatch and Lap timing. Press Start to start the time observation and Lap

to take a lap time. Press Stop to stop the lap timing. Press Options and you can save or reset the lap

times. Refer to Time observation and time splitting above.

Viewing and erasing times

Press Menu, select Extras, and Stopwatch.

If the stopwatch is not reset, you can select Show last to view the latest measured time. Select View

times and a list of names or final times of the time sets is shown, select the time set you want to view.

To delete the saved times, select Erase times. Select All at once and press OK, or select One by one,

scroll to the times you want to delete, press Erase and press OK.

■ Mobile Internet services, WAP (Menu 12)

See also WAP (Wireless Application Protocol) on page 16.

Note: Your phone must be switched on to use this function. Do not switch the phone on when wireless

phone use is prohibited or when it may cause interference or danger.

The WAP services use Wireless Mark-Up Language (WML) on their WAP pages. Web pages using the

Hyper Text Mark-Up Language (HTML) cannot be viewed on your phone.

Basic steps for accessing and using WAP services

1. Save the service settings that are needed to access the WAP service that you want to use. See

Setting up the phone for a WAP service below and Appearance settings of WAP browser on page 86.

2. Make a connection to the given WAP service. See Making a connection to a WAP service on page

83.

3. Start browsing the pages of the WAP service. See Browsing the pages of a WAP service on page 85.

4. Once you are finished browsing, end the connection to the WAP service. See Ending a WAP

connection on page 86.

Setting up the phone for a WAP service

You may receive the service settings as a text message from the network operator or service provider

that offers the WAP service that you want to use. For more information, contact your network operator

or service provider, or visit Club Nokia’s Web site (www.club.nokia.com).

You can also key in the settings manually. For appropriate settings, contact your network operator or

service provider. The WAP settings may be available, for example, on the Web site of the network

operator or service provider.

Saving the service settings received as a text message

When you receive the service settings as a text message, Service settings received is displayed.

• To save and activate the received settings, press Options and select Save.

If no settings are saved in Active service settings, the settings are saved under the first free

connection set and also activated.

• To discard the received settings, press Options and select Discard.

• To view the received settings first, press Options and select View. To save the settings, press Save.

Keying in the service settings manually

1. Press Menu, select Services, and Settings.

2. Select Active service settings.

You need to activate the set where you want to save the service settings. A set is a collection of

settings needed for making a connection to a WAP service.

3. Scroll to the set you would like to activate and press Activate.

4. Select Edit active service settings.

Select each of the service settings one by one and key in all the required settings.

•

Settings name - Key in the new name for the connection set and press OK.

Homepage - Key in the homepage address of the WAP service that you want to use, press

for a period, and press OK.

•

Session mode - Select Permanent or Temporary.

Connection security - Select On or Off.

When the connection security is On, the phone tries to use a secure connection with the WAP

service. If a secure connection is not available, the connection will not be made. If you wish to

connect anyway, with a non-secure connection, you must set the connection security to Off.

•

Data bearer - Select GSM data or GPRS. Settings for the selected bearer, see Settings when GSM

data is the selected data bearer and Settings when GPRS is the selected data bearer below.

For pricing, connection speed and other information, contact your network operator or service

provider.

Settings when GSM data is the selected data bearer

•

Dial-up number - Key in the phone number and press OK.

•

IP address - Key in the address, press

for a period, and press OK. You obtain the IP address

from your network operator or service provider.

•

Authentication type - Select Secure or Normal.

Data call type - Select Analogue or ISDN.

Data call speed - Select the speed you want to use, or select Automatic. Automatic is available only

if the current selected data call type is Analogue. The actual data call speed depends on the service

provider.

•

and password keyed in the following settings. If you select Manual, the login information is

required when establishing a connection.

•

User name - Key in the user name and press OK.

Password - Key in the password and press OK.

Settings when GPRS is the selected data bearer

•

GPRS connection - Select Always online or When needed.

If you select Always online, the phone is automatically registered to a GPRS network when you

switch the phone on. Starting a WAP or PC dial-up application creates the connection between

phone and network and data transfer is possible. When you end the application, GPRS connection is

ended but the registration to the GPRS network remains.

If you select When needed, the GPRS connection is established when you connect to a WAP service

and closed when you end the WAP connection.

•

GPRS access point - Key in the access point name and press OK.

An access point name is needed to establish a connection to a GPRS network. You obtain the access

point name from your network operator or service provider.

IP address - Key in the address, press

for a period, and press OK. You obtain the IP address

from your network operator or service provider.

•

Authentication type - Select Secure or Normal.

Always online, the Always online connection will be disabled.

•

User name - Key in the user name and press OK.

Password - Key in the password and press OK.

Making a connection to a WAP service

Firstly, make sure that the service settings of the WAP service you want to use are activated. To

activate the settings:

• Press Menu, select Services and Settings. Select Active service settings and scroll to the set you

want to activate and press Activate.

Secondly, make a connection to the WAP service. There are three ways to connect:

• Open the homepage of the WAP service:

Press Menu, select Services and Home.

Tip: To quickly open the homepage of a WAP service:

In standby mode, press and hold

• Select a bookmark of the WAP service:

Press Menu, select Services, Bookmarks, and select a bookmark.

If the bookmark does not work with the current active service settings, activate another set of

service settings and try again.

• Key in the address of the WAP service:

Press Menu, select Services and then Go to address. Key in the address of the WAP service, press

for special characters, and press OK.

Note that it is not necessary to add the prefix http:// in front of the address since it will be added

automatically.

Browsing the pages of a WAP service

After you have made a connection to the WAP service, you can start browsing its WAP pages. The

function of the phone keys may vary in different WAP services. Follow the text guides on the phone

display. For more information, contact your WAP service provider.

Note that if GPRS is selected as the data bearer, the indicator is shown on the top left of the display

during browsing. If there is an incoming (or outgoing) call during a GPRS connection, the indicator

will be shown on the top right of the display. The GPRS connection is suspended.

General guidelines for using the phone keys

• Use the scroll keys

to browse the WAP page.

• To select a highlighted item, press

• To enter letters and numbers, press the keys

the key

and to enter special characters, press

• Some or all of the following options are available while a WAP connection is in progress. Press

Options and select the option you want.

Home - to go back to the homepage of the WAP service

Bookmarks - the list of bookmarks is displayed. For details, see Bookmarks on page 87.

Edit / Open row / Open link / Open list - to key in text or select a highlighted item on the WAP page.

Add bookmark - to add the current WAP page as a bookmark in your bookmarks list.

Go to address - to key in the address of the WAP service you want.

Service inbox - the list of service messages is displayed, see Service inbox on page 88.

Appear. sett. - for details, see Appearance settings of WAP browser on page 86.

Download settings - for details, see Download settings on page 87.

Use number - to copy a number from the current WAP page for saving or calling (and ends the WAP

connection). If the WAP page contains several numbers, you may select the desired one.

Reload - to reload and update the current WAP page.

Clear the cache - for details, see The cache memory on page 89.

Security info - to view security information about the current WAP connection and the server.

Quit - to quit browsing and end the call.

The WAP browser supports functions which you can access while browsing. You can make a voice call

while you are on a WAP page, send DTMF tones while a voice call is in progress, and save in the phone

book a name and a phone number from a WAP page.

Ending a WAP connection

When you are using a WAP service, press Options and select Quit. When Quit browsing? is shown, press

Yes.

Alternatively, press

. If GSM data is the selected data bearer, press

twice.

The phone ends the call and terminates the connection to the WAP service.

Appearance settings of WAP browser

1. When no WAP connection is in progress

• Press Menu, select Services, Settings and Appearance settings.

When a WAP connection is in progress

• Press Options and select Appear. sett..

2. Select Text wrapping or Show images.

3. Select On or Off for Text wrapping and Yes or No for Show images.

When Text wrapping is set to On, the text continues on the next line if it cannot be shown on one

line.

When Show images is set to No, any pictures appearing on the WAP page are not shown. This can

speed up the browsing of WAP pages that contain a lot of pictures.

Download settings

You can set the phone to allow or prevent receiving cookies.

A cookie is data that a WAP site saves in your phone’s browser cache memory. The data can be, for

example, your user information or your browsing preferences. Cookies will be saved until you clear the

cache memory, see The cache memory on page 89.

1. When no WAP connection is in progress

• Press Menu, select Services, Settings and Download settings.

When a WAP connection is in progress

• Press Options and select Download settings.

2. Select Cookies and select Allow or Reject to allow or prevent the phone receiving cookies.

Bookmarks

You can save up to 25 WAP page addresses as bookmarks in the phone’s memory.

1. When no WAP connection is in progress

• Press Menu, select Services and then Bookmarks.

When a WAP connection is in progress

• Press Options and select Bookmarks.

2. Scroll to the bookmark you want to use and press Options.

3. Select one of the following options:

Go to to make a connection to the WAP page associated with the bookmark.

Edit or Erase to modify or delete the selected bookmark.

Send to send the selected bookmark to another phone via SMS, Via SMS.

New bookmark to create a new bookmark without connection to the WAP service. Key in the

address and the title of the WAP page and press OK.

Note that your phone may have some pre-installed bookmarks for sites not affiliated with Nokia. Nokia

does not warrant or endorse these sites. If you choose to access them, you should take the same

precautions, for security or content, as you would with any site.

Receiving a bookmark

When you have received a bookmark as an Over The Air (OTA) message, press Options and select View

to view the bookmark, Save to save the bookmark, or Discard to discard it.

Service inbox

The phone is able to receive service messages (pushed messages) sent by your service provider. Service

messages are notifications of, for example, news headlines, and they may contain a text message or

address of a WAP service.

1. To access service inbox when no WAP connection is in progress

When you have received a service message, 1 service message received will be displayed. Press View

to access the Service inbox.

If you press Exit the message is moved to the Service inbox. To access the Service inbox later, press

Menu, select Services, and Service inbox.

When a WAP connection is in progress

Press Options and select Service inbox.

2. Scroll to the message you want and press Options.

Select Retrieve to activate the WML browser and download the indicated content.

Select Details to display detailed information on the service notification.

Select Erase to delete the selected service notification.

To set the phone to receive service messages

Press Menu, select Services, Settings, Service inbox settings, and Service messages. To set the phone to

receive service messages, select On. If you select Off, the phone will not receive service messages.

The cache memory

Note: The information or services you have accessed are stored in the cache of your phone. A cache is a

buffer memory, which is used to store data temporarily. If you have tried to access or have accessed

confidential information requiring passwords (for example, your bank account), empty the cache of your

phone after each use.

To clear the cache memory when no WAP connection is in progress

• Press Menu, select Services, and Clear the cache.

To clear the cache memory when a WAP connection is in progress

• Press Options and select Clear the cache.

Authority certificates

For using some WAP services, such as banking services, you need an authority certificate. Using the

certificate can help you improve the security of connections between your phone and a WAP gateway

or WAP server, if the Connection security is set to On.

You can download the certificate from a WAP page if the WAP service supports the use of authority

certificates. After the download, you can view the certificate and then save or delete it. If you save the

certificate, it is added to the list of certificates in the phone.

You will see a note on the phone display if the identity of the WAP server or WAP gateway cannot be

verified, if the WAP server or WAP gateway certificate is not authentic or if you do not have the right

certificate in your phone.

Viewing the list of authority certificates

Press Menu, select Services, and Settings. Select Authority certificates.

See also Security info in General guidelines for using the phone keys on page 85.

Security indicator

If the security indicator

is displayed during a WAP connection, the data transmission between the

phone and the WAP gateway or WAP server (identified by the IP address in the Edit active service

settings) is encrypted.

However, the security indicator does not indicate that the data transmission between the gateway and

the content server (place where the requested resource is stored) is secure. It is up to the service

provider to secure the data transmission between the gateway and the content server.

■ SIM services (Menu 13)

In addition to the functions available on the phone, your SIM card may provide

additional services that you can access in menu 13. Menu 13 is shown only if it is

supported by your SIM card. The name and contents of the menu depend entirely on the service

available.

Note: For availability, rates and information on using SIM services, contact your SIM card vendor, e.g.

network operator, service provider or other vendor.

You can set the phone to show you the confirmation messages sent between your phone and the

network when you are using the SIM services by selecting the option Yes within the menu 4-4-5,

Confirm SIM service actions.

Note that accessing these services may involve sending a text message (SMS) or making a phone call

for which you may be charged.

8. Data and fax communication

You can transfer data to other compatible devices when your Nokia 8310 phone is connected to a

compatible PC via an IR connection.

To send and receive e-mail and faxes, and to connect to computers and access the Internet, you also

need the appropriate data and fax communications software installed on your computer. You can use

the Nokia 8310 with a variety of commercially available data and fax communications applications.

To use your phone as a modem, you first need to install it as a modem.

■ Communication applications and modem drivers

On the Nokia website, www.forum.nokia.com, you may find the required system files for data

communication and also the instructions for installation. You may also find documents that advise you

on how to set up devices and applications for use with the Nokia 8310.

PC Suite

PC Suite contains applications which help you

• to conveniently manage various phone functions from your PC

• to synchronise contacts and calendar items between your phone and your PC Personal Information

Manager.

• to draw and edit caller group graphics and picture messages.

• to create new ringing tones for your phone.

• to select the connection type used when connecting your PC and your phone.

• to back up and restore personal information from phone to PC or to another phone.

Modem setup

Modem setup installs the following components on your PC:

• N8310 data and fax modem adapters, which enable you to use your phone as a modem in data and

fax calls.

• Nokia Modem Options software to set options for the data calls you make. You find the settings for

HSCSD and GPRS here.

GPRS - General Packet Radio Service

See also GPRS modem settings on page 65.

HSCSD - High Speed Circuit Switched Data

With the GSM high-speed data service you can use the Internet and other services more quickly than

usual. When sending and receiving e-mail, the 14.4 kbps data transmission speed can be doubled up to

28.8 kbps. In Internet connections a download speed of up to 43.2 kbps can be achieved if supported by

the equipment of the network operator and the Internet service provider.

Note that sending data in HSCSD mode drains the phone’s battery faster than normal voice or data

calls as the phone is sending data faster. For continuous usage, connect the phone to a charger.

Using data communication applications

• Activate the IR connection of your phone by selecting Menu 9.

• Make sure that the infrared port of the phone faces the infrared port of the PC.

• Start using the data communications application on the PC.

For information on the use of the application, refer to the documentation for the application.

Note that making or answering phone calls during a PC connection is not recommended as it might

disrupt the operation.

For better performance during data calls, place the phone on a stationary surface with the keypad

facing downward. Do not move the phone by holding it in your hand during a data call.

9. Battery statements

■ Charging and Discharging

Your phone is powered by a rechargeable battery.

Note that a new battery’s full performance is achieved only after two or three complete charge and discharge

cycles!

The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating

time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery.

Use only batteries approved by the phone manufacturer and recharge your battery only with the chargers approved

by the manufacturer. Unplug the charger when not in use. Do not leave the battery connected to a charger for

longer than a week, since overcharging may shorten its lifetime. If left unused a fully charged battery will discharge

itself over time.

Temperature extremes can affect the ability of your battery to charge.

Use the battery only for its intended purpose.

Never use any charger or battery which is damaged.

Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object (coin, clip or pen)

causes direct connection of the + and - terminals of the battery (metal strips on the battery) for example when you

carry a spare battery in your pocket or purse. Short-circuiting the terminals may damage the battery or the

connecting object.

Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the

capacity and lifetime of the battery. Always try to keep the battery between 15°C and 25°C. A phone with a hot or

cold battery may temporarily not work, even when the battery is fully charged. Batteries' performance is

particularly limited in temperatures well below freezing.

Do not dispose of batteries in a fire !

Dispose of batteries according to local regulations (e.g. recycling). Do not dispose as household waste.

CARE AND MAINTENANCE

Your phone is a product of superior design and craftsmanship and should be treated with care. The suggestions

below will help you to fulfil any warranty obligations and to enjoy this product for many years.

•

Keep the phone and all its parts and accessories out of the reach of small children.

Keep the phone dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will

corrode electronic circuits.

•

Do not use or store the phone in dusty, dirty areas. Its moving parts can be damaged.

Do not store the phone in hot areas. High temperatures can shorten the life of electronic devices, damage

batteries, and warp or melt certain plastics.

•

Do not store the phone in cold areas. When it warms up (to its normal temperature), moisture can form inside,

which may damage electronic circuit boards.

•

Do not attempt to open the phone. Non-expert handling may damage it.

Do not drop, knock or shake the phone. Rough handling can break internal circuit boards.

Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the phone.

Do not paint the phone. Paint can clog the moving parts and prevent proper operation.

Use only the supplied or an approved replacement antenna. Unauthorised antennas, modifications or

attachments could damage the phone and may violate regulations governing radio devices.

All of the above suggestions apply equally to your phone, battery, charger or any accessory. If any of them is not

working properly, take it to your nearest qualified service facility. The personnel there will assist you and, if

necessary, arrange for service.

IMPORTANT SAFETY INFORMATION

■ Traffic Safety

Do not use a hand-held telephone while driving a vehicle. Always secure the phone in its holder; do not place the

phone on the passenger seat or where it can break loose in a collision or sudden stop.

Remember road safety always comes first!

■ Operating environment

Remember to follow any special regulations in force in any area and always switch off your phone whenever it is

forbidden to use it, or when it may cause interference or danger.

Use the phone only in its normal operating positions.

Parts of the phone are magnetic. Metallic materials may be attracted to the phone, and persons with a hearing aid

should not hold the phone to the ear with the hearing aid. Always secure the phone in its holder, because metallic

materials may be attracted by the earpiece. Do not place credit cards or other magnetic storage media near the

phone, because information stored on them may be erased.

■ Electronic devices

Most modern electronic equipment is shielded from radio frequency (RF) signals. However, certain electronic

equipment may not be shielded against the RF signals from your wireless phone.

Pacemakers

Pacemaker manufacturers recommend that a minimum separation of 20 cm be maintained between a handheld

wireless phone and a pacemaker to avoid potential interference with the pacemaker. These recommendations are

consistent with the independent research by and recommendations of Wireless Technology Research. Persons with

pacemakers:

•

Should always keep the phone more than 20 cm from their pacemaker when the phone is switched on;

Should not carry the phone in a breast pocket;

Should use the ear opposite the pacemaker to minimise the potential for interference.

If you have any reason to suspect that interference is taking place, switch off your phone immediately.

Hearing aids

Some digital wireless phones may interfere with some hearing aids. In the event of such interference, you may

want to consult your service provider.

Other medical devices

Operation of any radio transmitting equipment, including cellular phones, may interfere with the functionality of

inadequately protected medical devices. Consult a physician or the manufacturer of the medical device to

determine if they are adequately shielded from external RF energy or if you have any questions. Switch off your

phone in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health

care facilities may be using equipment that could be sensitive to external RF energy.

Vehicles

RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (e.g.

electronic fuel injection systems, electronic anti-skid (anti-lock) braking systems, electronic speed control systems,

air-bag systems). Check with the manufacturer or its representative regarding your vehicle. You should also

consult the manufacturer of any equipment that has been added to your vehicle.

Posted facilities

Switch your phone off in any facility where posted notices so require.

100

■ Potentially explosive atmospheres

Switch off your phone when in any area with a potentially explosive atmosphere and obey all signs and

instructions. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death.

Users are advised to switch off the phone when at a refuelling point (service station). Users are reminded of the

need to observe restrictions on the use of radio equipment in fuel depots (fuel storage and distribution areas),

chemical plants or where blasting operations are in progress.

Areas with a potentially explosive atmosphere are often but not always clearly marked. They include below deck on

boats; chemical transfer or storage facilities; vehicles using liquified petroleum gas (such as propane or butane);

areas where the air contains chemicals or particles, such as grain, dust or metal powders; and any other area where

you would normally be advised to turn off your vehicle engine.

■ Vehicles

Only qualified personnel should service the phone, or install the phone in a vehicle. Faulty installation or service

may be dangerous and may invalidate any warranty which may apply to the unit.

Check regularly that all wireless phone equipment in your vehicle is mounted and operating properly.

Do not store or carry flammable liquids, gases or explosive materials in the same compartment as the phone, its

parts or accessories.

For vehicles equipped with an air bag, remember that an air bag inflates with great force. Do not place objects,

including both installed or portable wireless equipment in the area over the air bag or in the air bag deployment

area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result.

Using your phone while in the air is prohibited. Switch off your phone before boarding an aircraft. The use of

wireless telephones in an aircraft may be dangerous to the operation of the aircraft, disrupt the wireless telephone

network and may be illegal.

Failure to observe these instructions may lead to suspension or denial of telephone services to the offender, or legal

action or both.

101

■ Emergency calls

Important: This phone, like any wireless phone, operates using radio signals, wireless and landline

networks as well as user-programmed functions. Because of this, connections in all conditions can not be

guaranteed. Therefore, you should never rely solely upon any wireless phone for essential communications

(e.g. medical emergencies).

Emergency calls may not be possible on all wireless phone networks or when certain network services and/or phone

features are in use. Check with local service providers.

To make an emergency call:

1. If the phone is not on, switch it on. Check for adequate signal strength.

Some networks may require that a valid SIM card is properly inserted in the phone.

2. Press

as many times as needed (e.g. to exit a call, to exit a menu, etc.) to clear the display and ready the

phone for calls.

3. Key in the emergency number for your present location (e.g. 112 or other official emergency number).

Emergency numbers vary by location.

4. Press the

key

If certain features are in use, you may first need to turn those features off before you can make an emergency call.

Consult this guide and your local cellular service provider.

When making an emergency call, remember to give all the necessary information as accurately as possible.

Remember that your wireless phone may be the only means of communication at the scene of an accident - do not

cut off the call until given permission to do so.

■ Certification information (SAR)

THIS MODEL PHONE MEETS THE EU REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.

102

Your mobile phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the limits for

exposure to radiofrequency (RF) energy recommended by The Council of the European Union. These limits are part

of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines

were developed by independent scientific organisations through periodic and thorough evaluation of scientific

studies. The limits include a substantial safety margin designed to assure the safety of all persons, regardless of age

and health.

The exposure standard for mobile phones employs a unit of measurement known as the Specific Absorption Rate, or

SAR. The SAR limit recommended by The Council of the European Union is 2.0 W/kg.* Tests for SAR have been

conducted using standard operating positions with the phone transmitting at its highest certified power level in all

tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level

of the phone while operating can be well below the maximum value. This is because the phone is designed to

operate at multiple power levels so as to use only the power required to reach the network. In general, the closer

you are to a base station antenna, the lower the power output.

Before a phone model is available for sale to the public, compliance with the European R&TTE directive must be

shown. This directive includes as one essential requirement the protection of the health and the safety for the user

and any other person. The highest SAR value for this model phone when tested for compliance against the standard

was 0.82 W/kg. While there may be differences between the SAR levels of various phones and at various positions,

they all meet the EU requirements for RF exposure.

* The SAR limit for mobile phones used by the public is 2.0 watts/kilogram (W/kg) averaged over ten grams of tissue.

The limit incorporates a substantial margin of safety to give additional protection for the public and to account for

any variations in measurements. SAR values may vary depending on national reporting requirements and the

network band. For SAR information in other regions please look under product information at www.nokia.com.

103

LIMITED MANUFACTURER’S WARRANTY

PART OF EUROPE & AFRICA REGION

This limited warranty shall apply in part of Nokia

which all by their nature have a limited lifetime, and

breakage or damage to antennas) unless the defect

was caused directly by defects in materials, design or

workmanship;

Mobile Phones’ Europe & Africa Region unless a local

warranty exists. Nokia Corporation, Nokia Mobile

Phones (”Nokia”) warrants that this NOKIA product

(”Product”) is at the time of its original purchase free

of defects in materials, design and workmanship

subject to the following terms and conditions:

(ii) Nokia or its authorized service company was not

notified by the Customer of the defect within thirty

(30) days after the appearance of the defect within

the warranty period;

1. This limited warranty is given to the end-purchaser

of the Product (”Customer”). It shall neither

exclude nor limit i) any mandatory statutory rights

of the Customer or ii) any of the Customer’s rights

against the seller/dealer of the Product.

(iii) the Product was not returned to Nokia or its

authorized service company within thirty (30) days

after the appearance of the defect within the

warranty period;

2. The warranty period is twelve (12) months from

the date on which the first Customer purchased

the Product. In case of a subsequent purchase or

other change of owner/user, such warranty period

shall continue for the remaining part of the twelve

(12) month period and otherwise remain

unaffected. This limited warranty is only valid and

enforceable in the following countries: Bosnia,

Bulgaria, Croatia, Cyprus, the Czech Republic,

Estonia, any member state of the European Union,

Hungary, Iceland, Israel, Latvia, Lithuania,

Macedonia, Malta, Norway, Poland, Romania, the

Slovak Republic, Slovenia, Switzerland and Turkey.

(iv) the Product serial number, the accessory date

code or the IMEI number has been removed, erased,

defaced, altered or is illegible;

(v) the defect was caused by a defective function of

the cellular network;

(vi) the defect was caused by the fact that the

Product was used with or connected to an accessory

not manufactured and supplied by Nokia or used in

other than its intended use;

(vii) the defect was caused by the fact that the

battery was short-circuited or seals of the battery

enclosure or cells were broken or show evidence of

tampering or the battery was used in equipment

other than for which it has been specified; or

3. During the warranty period Nokia or its authorized

service company will repair or replace, at Nokia’s

sole discretion, a defective Product. Nokia will

return the repaired Product or another Product to

the Customer in good working condition. All parts

or other equipment for which replacements have

been provided shall become the property of Nokia.

(viii) the Product software needs to be upgraded due

to changes in cellular network parameters.

4. A repaired or replaced Product will not be given a

prolonged or renewed warranty period.

7. To claim this limited warranty the Customer shall

present either i) a legible and non-modified

original warranty card which clearly indicates the

name and address of the seller, the date and place

of purchase, the product type and the IMEI or

other serial number or alternatively ii) a legible and

non-modified original purchase receipt which

contains the same information, if such purchase

receipt is presented to the seller/dealer of the

Product.

5. This limited warranty will not cover painted covers

or other similar personalized parts. In all cases that

require unlocking or locking of an operator SIM-

lock, Nokia will first direct the Customer to such

operator for unlocking or locking of the operator

SIM-lock before repairing or replacing the Product.

6. This limited warranty shall not apply to

deterioration due to normal wear and tear. This

limited warranty shall further not apply if:

8. This limited warranty is the Customer’s sole and

exclusive remedy against Nokia and Nokia’s sole

and exclusive liability against the Customer for

defects or malfunctions of the Product. This limited

warranty replaces all other warranties and

liabilities, whether oral, written, (non-mandatory)

statutory, contractual, in tort or otherwise. Nokia is

in no event liable for any incidental, consequential

or indirect damage, costs or expenses. Neither is

Nokia in any event liable for any direct damage,

costs or expenses, if the Customer is a legal person.

(i) the defect was caused by the fact that the Product

has been subjected to: use in contradiction with the

owner’s/user manual, rough handling, exposure to

moisture, dampness or extreme thermal or

environmental conditions or rapid changes in such

conditions, corrosion, oxidation, unauthorized

modifications or connections, unauthorized opening

or repair, repair by use of unauthorized spare parts,

misuse, improper installation, accident, forces of

nature, spillage of food or liquid, influence from

chemical products or other acts beyond the

9. Any change or amendment to this limited warranty

requires Nokia’s prior written consent.

reasonable control of Nokia (including but not limited

to deficiencies in consumable parts, such as batteries

9359974/02

WARRANTY CARD

FILL IN WITH BLOCK LETTERS

Purchaser’s Name: _____________________________________________________

Address: _____________________________________________________________

_____________________________________________________________

Country: _____________________________________________________________

Phone: ______________________________________________________________

Date of Purchase (dd/mm/yy):

Product Type (on phone type label under battery):

Product Model (on phone type label under battery):

Phone Serial No (on phone type label under battery):

–

Place of Purchase: _____________________________________________________

Store Name:__________________________________________________________

Store Address: ________________________________________________________

Stamp

Timex T625B User Manual
Teac HD 35 MOVIE User Manual
Teac Compact Disc Player CD P650 User Manual
Seagate ST315005EXM101 RK User Manual
Samsung SSD 840 MZ7TD120KW User Manual
Samsung SH S223C User Manual
Samsung SGH E335 User Manual
Pioneer DEH P7000BT User Manual
Philips Senseo HD7814 User Manual
Palm TheTreoTM 600 User Manual