19IOM-5
INSTALLER
READ THESE INSTRUCTIONS CAREFULLY. THEY WILL
SAVE TIME IN ASSEMBLING BOILER
19A SERIES BOILER
INSTALLATION
INSTRUCTIONS
STEAM OR WATER HEATING
PRESSURIZED FOR FIRING OIL, GAS
OR COMBINATION GAS/OIL
DESIGNED AND TESTED ACCORDING TO THE A.S.M.E.
BOILER AND PRESSURE VESSEL CODE, SECTION IV
FOR MAXIMUM ALLOWABLE WORKING PRESSURE.
STEAM - 15 PSIG, WATER - 80 PSIG
CANADA: STEAM - 15 PSIG, WATER - 50 PSIG
CAUTION
Do not use automotive anti-freeze in boiler waterways. If necessary to use anti-
freeze, be sure to employ a preparation designed for hydronic heating systems
such as ethylene or propylene glycol.
Water treatment is not recommended. This boiler uses gaskets to seal the ports
of adjoining sections. These gaskets are made of a fluorocarbon elastomer
(designation FKM) marketed under the brand name Viton. Consult a water
treatment professional before adding any chemical to the boiler water. Any
water treatment or anti-freeze added to the system must be compatible with the
Viton gaskets.
THE SECTIONS OF THIS BOILER MUST BE ASSEMBLED
TO THE PROPER TORQUE. READ INSTRUCTIONS
THESE INSTRUCTIONS TO BE LEFT WITH THE BOILER FOR REFERENCE PURPOSES
WESTCAST, INC.
260 NORTH ELM STREET WESTFIELD, MA 01085
TEL. (413) 562-9631 FAX (413) 562-3799
PAGE 3
19A SERIES BOILER
INSTALLATION INSTRUCTIONS
TABLE OF CONTENTS
SECTION
DESCRIPTION
PAGE
SECTION
DESCRIPTION
PAGE
19A SERIES ISOMETRIC DRAWING
PARTS LIST
TABLE OF CONTENTS
GENERAL INFORMATION
BOILER LOCATION
CODES AND REGULATIONS
CHIMNEY AND BREECHING
COMBUSTION AND VENTILATION AIR
ASSEMBLY OF SECTIONS
HYDROSTATIC TEST
2
2
3
3
3
3
3
4
4
5
5
6
10
11
12
13
14
15
16
17
18
19
TANKLESS HEATERS
SMOKEHOOD
6
6
7
8
8
8
8
8
9
BURNER MOUNTING PLATE
CLEANOUT COVERS
REAR OBSERVATION PORT
CONTROL LOCATIONS
JACKET
SAFETY AND RELIEF VALVES
CLEANING BOILER WATERWAYS
OWNER'S INSTRUCTIONS
CONTROL TAPPINGS DIAGRAM
WARNING
1
2
3
4
5
6
7
8
9
9
10
11
STEAM PIPING
WATER PIPING
3. CODES AND REGULATIONS
1. GENERAL
All work in connection with the boiler, burner and controls
must be performed in strict accordance with requirements of
state and local authorities having jurisdiction over boiler
installations.
19A Series boilers are wet-base, extended surface, vertical
flue design with integral cast flue gas collector for pressurized
firing with oil, gas or combination power burners. Upper and
lower port hydronic seals are of a special material resistant to
petroleum products and compatible with ethylene and
propylene based anti-freeze (non automotive type) which does
not contain corrosion inhibitors to protect aluminum. The flue
gas joints between sections, etc. are sealed using high
temperature (2300°F) ceramic fiber rope. Access to the heating
surface for cleaning is provided from the left hand side of the
boiler through large cast iron cover plates. A slide damper is
provided in the flue gas outlet for back pressure adjustment.
32"
JACKET SIDE PANEL
OF BOILER
C
FLOOR
OR PAD
L
1 1/2" x 2 1/2" ANGLES
The boilers are supplied completely knocked down for field
assembly, as factory assembled blocks of sections or
completely assembled boiler-burner units. All items should be
inspected for damage upon receipt, and any damage reported
to the wholesaler and trucker. All components should be
stored in a clean, dry area.
4 5/32"
12 27/32"
12 27/32"
4 5/32"
25 21/32"
34"
FIGURE 1
The boilers are conservatively rated for high efficiency
performance with capability for down-firing to match connected
load. The large OBROUND upper port provides transfer area
above the water surface for dry steaming at full load.
In the absence of such local requirements, the following should
govern:
A.S.M.E. Section IV - “Heating Boilers"
A.S.M.E. Section VI - “Care and Operation of Boilers”
ANSI/NFPA 31 - “Installation of Oil Burning Equipment”
ANSI/Z223.1 - “National Fuel Gas Code”
ANSI/NFPA 70 - “National Electrical Code”
2. BOILER LOCATION
The boiler must be installed on a smooth, level, non-
combustible floor or pad as close to the chimney or vent
location as possible to minimize breeching length. Allow
clearance around the boiler for piping, service, maintenance,
cleaning and tankless coil removal. Approximately 30 inches
on the sides is a minimum (Check local code requirements).
Do not install electrical conductors in floor or pad under boilers.
4. CHIMNEY AND BREECHING
The breeching connection between boiler and chimney should
be as direct as possible with the minimum number of elbows or
bends. It should pitch upwards to the chimney at a rate of 1/4
inch per foot of horizontal run. Generally, the breeching and
chimney should be the same diameter as the boiler outlet
connection.
See FIGURE 1 for boiler floor pad requirements, and TABLE
1 for minimum required pad length.
TABLE 1
NOTE
Boiler No.
Min. Recommended Pad Length
11 and 12 section uses adapter collar for connection to
12" diameter vent system.
19-*-3
19-*-4
19-*-5
19-*-6
19-*-7
19-*-8
19-*-9
19-*-10
19-*-11
19-*-12
30"
36"
42"
48"
54"
60"
66"
72"
78"
84"
For fuel conservation and stable burner performance, the
vent connection from the boiler should not include a barometric
draft control or other opening unless the venting system can
develop an excessive draft, or is required by code.
PAGE 4
19A SERIES BOILER
INSTALLATION INSTRUCTIONS
5. COMBUSTION AND VENTILATION AIR
CAUTION
An adequate supply of air for the boiler room must be provided
to allow complete combustion of fuel and ventilation of the
room to avoid excessively high ambient temperature. Air inlet
by natural ventilation directly from the outside shall have
total free area of not less than one sq. in. per 14,000 BTU
per hour of input of all fuel burning appliances in the boiler
room.
Due to the fact that the sections are top heavy, it is
absolutely necessary that the back section be supported
in such a manner as to prevent its falling and causing
potential serious bodily injury while preparing to add the
next section. One such way would be to insert a piece of
3" x 36" piping in the lower port.
Where combustion air must be obtained through ducts, see
ANSI/NFPA 31 or ANSI Z223.1 for requirements.
NOTE
Somesectionsmayneedshimsundersupportfeettoalign
with other sections.
If mechanical combustion air supply is required, the system
must be approved by the local authorities, and should provide
at least 30 CFM per gallon of oil and 0.25 CFM per MBH of
gas input to the boilers.
Stand the back section in place with the feet on and in the
angle iron rails. Support the section as required to prevent it
from falling forward or rearward. Clean hydronic gasket
recesses and rope groove with a stiff wire brush. Apply
spray-on adhesive (supplied with the boiler) to rope groove
to hold wicking in place during assembly.
Ventilation air, if required, must be in addition to the
combustion air quantities called for above.
6. ASSEMBLY OF SECTIONS
CAUTION
When boilers are delivered to the job site, each item should
be inspected closely for possible shipping damage. Scars or
nicks in the port sealing surfaces may allow leakage. Do not
attempt to use any section that has been damaged in the
port seal area.
Do not spray adhesive into the hydronic seal ports.
Apply a length of wicking avoiding bends and twists. Be sure
ends extend past the cleanout cover opening. (See FIGURE
2) Place the upper and lower hydronic seals in the recessed
section taking care not to dislodge the rope or the hydronic
seals. Inspect the alignment of the sections through the open
ports and, if properly aligned, install the draw rods with nuts
drawn hand-tight. (See FIGURE 3.) Plumb the sections before
applying torque to the upper right and lower left draw rods.
Maintain finger-tight torque on upper left and lower right draw
rods.
When ready to commence assembly, recommended on a
level pad, place the angle rails in position parallel with each
other with the 2" legs on the floor and measuring 25-21/32
inches outside dimension. Be sure to align the center of the
boiler with the center line of the pad. If no pad is provided,
shim and grout under the angles to make them level and
provide support along the full length. See FIGURE 1. Clean
hydronic gasket recesses and rope groove with a wire brush,
taking care not to damage machine surface.
CLEANOUT COVER
See TABLE 2 for proper location of sections.
UPPER PORT
HEATING
SURFACE
TABLE 2
3 SECT
4 SECT
5 SECT
6 SECT
7 SECT
8 SECT
9 SECT
10 SECT
11 SECT
12 SECT
F
F
F
F
F
F
F
F
F
F
H
P
H
P
H
P
P
P
P
P
B
H
P
H
P
H
H
P
P
P
CERAMIC ROPE
JOINT SEAL
B
H
P
H
P
P
H
P
P
LOWER PORT
B
H
P
H
H
P
H
P
FLOOR
B
H
P
P
H
P
H
B
H
H
P
H
P
B
P
H
P
H
SECTIONAL VIEW
B
P
H
P
FIGURE 2
B
P
H
B
P
IMPORTANT
B
The upper and lower ports should be drawn up metal to
metal around the outside of the hydronic seal. Metal to
metal conditions will not occur at any other location.
Avoid excessive torque on upper left and lower right
draw rods, which may warp the section. See FIGURE 3
for correct alignment of the seal.
F = Front Section
P = Plain intermediate section
H = Heater intermediate section-Optional, must be ordered.
B = Back Section
Assemble additional sections as described above.
After draw rods are hand tight, torque as shown in TABLE 3.
PAGE 5
19A SERIES BOILER
INSTALLATION INSTRUCTIONS
2. Water Boilers – The assembled boiler shall be subjected
to a hydrostatic test pressure not less than 1-1/2 times the
maximum allowable working pressure.
TABLE 3
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
STEP 7
STEP 8
STEP 9
STEP 10
UPPER RIGHT
LOWER LEFT
UPPER LEFT
LOWER RIGHT
UPPER RIGHT
LOWER LEFT
UPPER RIGHT
LOWER LEFT
UPPER LEFT
LOWER RIGHT
5 FT. LBS.
5 FT. LBS.
5 FT. LBS.
5 FT. LBS.
25 FT. LBS.
25 FT. LBS.
50 FT. LBS.
50 FT. LBS.
10 FT. LBS.
10 FT. LBS.
3. The required test shall not exceed the test pressure by
more than 10 PSI.
Excessive torque on draw rods may damage castings. Do
not exceed the torque shown in TABLE 3.
In a cold environment, hydronic seals may not quickly conform
to sealing surfaces when properly compressed. Under such
conditions, hydrostatic testing with cold water might show
weeping or leaking at the seals. To avoid this possibility,
delay filling the boiler with cold water for a few hours after
assembly, or use warm water, if available, for the tests.
Prepare additional intermediate sections and install in the
same manner described above. Be sure each section is
properly sealed against water leakage and flue gas exfiltration.
Be certain the angle rails remain level and provide support
for each section as it is assembled. Check each section for
vertical position.
If there is seepage about chaplets or minor leakage, consult
the Smith Company representative for advice regarding
A.S.M.E. Code approved repairs by peening or plugging.
8. STEAM PIPING
When all sections, including the front section or back are in
place, check all draw rods to insure iron-to-iron contact at
ports. DO NOT APPLY EXCESSIVE TORQUE. See TABLE
3 for recommended torques.
A steam piping schedule is shown in TABLE 4. Pitch piping
to allow condensate to flow in the same direction as steam.
Makeup water connections must be made to the return piping,
not directly to the boiler. Install blow-down valves as required.
See FIGURE 4 for recommended acceptable steam piping
arrangement.
TABLE 4
HYDRONIC
SEAL
BOILER SIZE
NO. OF 3" RISERS
HEADER
EQUALIZER
3 THRU 5 SECTION
6 THRU 10 SECTION
11 AND 12 SECTION
1
2
2
3"
4"
5"
1-1/2"
2"
2-1/2"
CORRECT
STEAM SUPPLY
TO SYSTEM
GATE VALVE
3" STEAM RISER(S)
SUPPORT DISCHARGE
PIPE
STEAM HEADER
EQUALIZER
CONNECTION
HYDRONIC
SEAL
*
TERMINATE DISCHARGE
PIPE SO AS TO AVOID
BOILER WATER LINE
41 1/4" ABOVE FLOOR
DISCHARGE ON PERSONS
INCORRECT
SEALING SECTIONS
GATE VALVE
ALTERNATE RETURN
CONNECTION
FIGURE 3
2" BELOW MINIMUM
BOILER WATER LINE
C.W. MAKEUP
CONNECTION
7. HYDROSTATIC TEST
Plug tappings, fill boiler with water and vent air from top of
boiler. Check for leaks. Leakage at seals may be due to
misalignment of hydronic seals. Loosen draw rods, reposition
seals and retest as above.
GATE VALVE
SAFETY VALVE
*
RETURN
CONNECTION
BLOWDOWN VALVE
TO DRAIN
All completed boilers shall satisfactorily pass the hydrostatic
tests as prescribed by A.S.M.E., Code Section IV.
TYPICAL STEAM PIPING DIAGRAM
FIGURE 4
1. Steam Boilers – The assembled boiler shall be subjected
to a hydrostatic test of not less than 45 PSIG.
PAGE 6
19A SERIES BOILER
INSTALLATION INSTRUCTIONS
TABLE 5
WATER 1"
SYSTEM SUPPLY
CONNECTIONS
CHECK VALVE
CIRCULATOR
NUMBER EVAPOR.
CONDENSATE
RECEIVER
MIN. FEED
OF
SECTIONS
RATE
GPM
BELOW WATER WATER PUMP
GATE VALVE
RELIEF VALVE
CAP.-GAL.
LEVEL GAL.
RATE-GPM
EXPANSION
TANK
3
4
.61
.85
1.4
1.9
2.4
2.9
3.3
3.8
4.3
4.8
5.2
5.7
1.22
1.70
2.37
3.04
3.71
4.38
5.05
5.72
6.39
7.06
12
16
22
29
35
41
47
54
60
66
AIR REMOVAL
PIPING
SUPPORT RELIEF VALVE
DISCHARGE PIPE
5
1.19
1.52
1.86
2.19
2.53
2.86
3.20
3.53
GATE
VALVE
6
TERMINATE DISCHARGE
PIPE SO AS TO AVOID
7
DISCHARGE ON PERSONS
C.W. MAKEUP
CONNECTION
8
9
10
11
12
PRESSURE
REGULATING
VALVE
SYSTEM RETURN
CONNECTION
Feed water makeup requirements.
GATE VALVE
NOTE
These recommendations are considered normal for
compact buildings on the basis of 80% receiver use.
Where buildings are spread out, additional receiver
capacity may be necessary because of the extended
time required for condensation to return to the receiver.
BLOWDOWN VALVE
TO DRAIN
TYPICAL WATER PIPING DIAGRAM
FIGURE 5
9. WATER PIPING
10. TANKLESS HEATERS
See FIGURE 5 for acceptable water piping diagram. TABLE
6 gives pumping rate and supply & return sizing for standard
installations.
Heater openings are provided for below-the-water-line tankless
heater coils in all special intermediate sections when ordered.
See TABLE 2 for the conr•ct placement of these heater
sections. Install the low limit temperature control in the 3/4"
tap located in the center of the coil.
TABLE 6
BOILER SIZE
GPM
RETURN CONN.
SUPPLY CONN.
If the heater sections are installed in an order other than in
TABLE 2 the jacket panels will not match.
3
4
30
41
2"
2"
2"
2"
11. SMOKE HOOD
5
58
2-1/2"
3"
2-1/2"
3"
Install smoke hood with the correct size smoke pipe
connecting collar using the 5/16" x 1-1/2" studs and hex nuts
furnished in screw seats in the back section. Apply self-
adhesive insulating tape (Items 21 and 22 in Parts detail
drawing on Page 2) to smoke hood flange and damper angle
Item 23. Fasten the slide damper in the open position for
starting the burner adjustment process.
6
74
7
90
3"
3"
8
106
123
139
155
171
3"
3"
9
3"
3"
10
11
12
3"
3"
3"
4"
See FIGURE 6 for recommended “L” coil piping and FIGURE
7 for SM9-18 single and/or dual piping arrangements.
3"
4"
Based on 20°F system temperature drop.
NOTE
Boiler supplied with 4" water supply tapping and 3" return
tapping.
PAGE 7
19A SERIES BOILER
INSTALLATION INSTRUCTIONS
The sealing rope should be placed in the groove on the
HOT
boiler side of the plate using adhesive to hold it in place. The
insulation block has a burner opening and a cutout for the
observation opening. Locate the block with the high
temperature facing on the fire side in the opening in the front
section. The burner mounting plate insulating block for
Beckett burners is installed with the dished side facing
towards the combustion chamber.
WATER
SUPPLY
TANKLESS
HEATER
TEMPERING VALVE
TEMPERATURE GAUGE
OUT
IN
OPERATING
CONTROL
TEMPERED
WATER
SUPPLY
UNIONS
Attach the block to the plate with the four 1/4" x 5" machine
screws and 1-1/2" O.D. washers, the washers on the insulation
block side. At the time of burner installation, the hole in the
insulation block may have to be enlarged. See separate burner
installation booklet for further assistance and dimensions.
COLD
WATER
INLET
FLOW LIMITING VALVE
GATE VALVE
NOTE
FIGURE 6 — TANKLESS PIPING
Tighten burner mounting plate screws evenly to slightly
compress rope gasket. Overtightening will cause plate
cracking at corners.
OPERATING
CONTROL
TANKLESS
HEATER
HOT
WATER
SUPPLY
NOTE
GATE VALVE
Most large burners require support to the floor. See burner
manufacturer's manual for such specifications if needed.
OUT
IN
OUT
IN
TEMPERING VALVE
TEMPERATURE GAUGE
TEMPERED
WATER
SUPPLY
UNION
GATE VALVE
COLD
WATER
INLET
FLOW LIMITING VALVE
Insulating Block
FIGURE 7 — DUAL TANKLESS PIPING
12. BURNER MOUNTING PLATE & TARGET WALL
The new target wall used on 3-6 section boilers must be
positioned with the flat side tight against the rear casting
and with the bottom side resting on the floor of the combustion
chamber. No glues or fasteners are used to secure the target
wall.
Target Wall
Each boiler is provided with a cast iron burner mounting
plate with an appropriate burner opening and tapped holes
for studs to accommodate burner flange. The mounting plate
is furnished with 1/4" diameter sealing rope and an insulation
block which should be installed on the plate before placing
the plate on the boiler. (See exploded view on page 2, Items
11-13 & FIGURE 8.)
FIGURE 8
PAGE 8
19A SERIES BOILER
INSTALLATION INSTRUCTIONS
13. CLEANOUT COVERS
15. CONTROL LOCATIONS
Be sure the rope seals are in place around the groove in the
cleanout cover plate. Install the plates on the boiler sections
carefully to insure proper sealing all around, using the
5/16" x 2" special anchor bolt and 5/16" hex head nuts. After
periodic flue cleaning, replace nuts at 10 lbs. torque. Use
Hi-Temp silicone caulk to seal covers air-tight.
NOTE
Jacket front panel should be in place before controls on
front of front section are installed.
Refer to FIGURE 11 showing locations recommended for
steam and water boiler limit and operating controls. Note the
requirement for an operating temperature control whenever
a tankless heater is called for. This is in addition to pressure
limit controls and other operating controls on steam boilers.
14. REAR OBSERVATION PORTS 7-12 SECTIONS
INSTRUCTIONS FOR ASSEMBLY:
1. Locate steel “flapper door” (Item 6) as shown in FIGURE
9 below. Drive Item 7, “expansion pin”, into hole in Item 1
to secure 6 in position.
NOTE
On steam boilers the 1" close nipple and 1" x 1/4"
reducing coupling for operating control should be installed
prior to jacket top panels.
2. Lift Item 6 up and install Item 2, “hex bolt”.
3. Slide Item 3, “compression spring” over the hex bolt and
screw Item 4 “hex nut” to hex bolt.
16. JACKET
Jacket assembly details are contained in a separate instruction
booklet.
4. Screw Item 5, “ball knob” into position and lock location
using Item 4 as a “jam” nut.
17. SAFETY AND RELIEF VALVES
5. Adhere 24-1/2" insulating tape as shown to Item 1.6.
Mount assembly to back section of boiler.
Safety and relief valves sized on the output rating of each
boiler size are furnished along with the necessary pipe and
fittings for installation in the back section. The valve discharge
connections should be piped to a location where people will
not be exposed to hot vapor or liquid. Any discharge piping
should be supported so as to prevent exerting any strain on
the valve body by the weight of the piping. See FIGURE 10.
7. 3-6 section boilers use a solid cover which is installed the
same way.
7
6
5
1
4
2
FOR DISCHARGE PIPING THROUGH ROOF CONSULT THE SMITH COMPANY
3
RELIEF OR SAFETY VALVE
DO NOT REMOVE RATING
OR WARNING TAGS.
SUPPORT DISCHARGE
PIPING SO AS TO AVOID
STRAIN ON VALVE BODY
INSULATING TAPE
FIGURE 9
DISCHARGE PIPE SIZE
TO EQUAL VALVE OUTLET.
DO NOT RESTRICT FLOW.
IMPORTANT
Item 6 must always be part of the assembly. Check
condition twice a year and replace as needed.
DISCHARGE SO AS TO
AVOID EXPOSURE OF
PERSONS TO HOT
LIQUID OR VAPOR.
LEAVE OPEN END
VISIBLE FOR PERIODIC
INSPECTION FOR SLOW
LEAKAGE OR DRIPS.
FIGURE 10
Some state and local codes require steam safety valves be
piped to the atmosphere outside the building.
PAGE 9
19A SERIES BOILER
INSTALLATION INSTRUCTIONS
18. CLEANING BOILER WATERWAYS
19. OWNERS INSTRUCTIONS
A. STEAM BOILERS
A. For best performance of the boiler, the following
suggestions should be performed by a qualified boiler room
technician, through a regular program of maintenance and
adjustment to obtain the following.
NOTE
The boiler should be cleaned before connecting system
piping and installing steam trim.
1. Oil burner combustion: 12 to 12 1/2 + % CO2, zero smoke,
smooth lightoff and operation.
1. Plug unused openings all around the boiler leaving a valved
overflow pipe connected to the safety valve tapping. Also
provide a valved blow-down connection to one of the
bottom tappings.
Gas burner combustion: 10 to 10 1/2% CO2, 0.02% CO,
smooth lightoff and operation.
2. The fuel burning equipment should be installed and made
ready to operate in accordance with the burner instructions.
2. Keep boiler fireside surface clean. Flue gas temperature
reading above 450°F over boiler room temperature signals
the start of soot accumulation. Inspect at least twice each
year.
3. Fill the boiler with water to the middle of the upper port,
adding a boiler cleaning compound, as recommended in
A.S.M.E. Section VI.
3. Steam boiler water condition should be observed. Unstable
water line, system steam hammer indicate dirty water.
Blow-down is recommended. However, the introduction of
excess raw water to a steam boiler can result in the deposit
of scale and inefficient operation of physical damage to
the boiler.
4. Fire the boiler for at least one hour at a low rate to
circulated the cleaning compound through the boiler.
5. Blow off surface of boiler water through skimmer connection
or through safety valve opening by feeding clean water
into the boiler through a bottom fill connection.
4. Float operated and probe type low water cutoff devices
should be maintained according to the instructions of the
manufacturer.
6. When the water coming off the surface runs clear, shut off
the burner, close the top valve and open the bottom blow-
down valve. If there is a slight steam pressure in the
boiler, it will assist the blow-down.
5. Limit control function should be checked on a regular basis.
6. Flame safeguard controls should be checked regularly.
7. When the sections have cooled after blow-down, flush the
interior of the boiler from the top by introducing water from
a hose through the top port. When the water runs clear,
complete the system piping, install the steam trim and
controls. Fill the boiler with clean water. Heat the boiler
water to at least 180°F to release corrosive gases.
B. The products of combustion must be conducted to the
outdoors by means of a metal connector of at least the same
size as the boiler smokehood outlet and a chimney or stub-
stack. The boiler is constructed for pressurized operation
and the burners are selected for operation against a back
pressure of 0.10 ins. w.c. at the boiler outlet. If the actual
conditions cause a back pressure in excess of 0.10 ins. w.c.
at the boiler outlet, consult the Smith Co. for verification of
burner size. If the chimney has the ability to develop excess
draft, a barometric draft control should be installed in the
chimney. Check with the Smith representative for assistance.
B. WATER BOILERS
NOTE
The system piping should be completed before cleaning
the boiler.
1. Add an approved boiler compound. Follow the compound
manufacturer's instructions for best results. Fill the system
and vent air wherever necessary.
2. Heat the water to at least 180°F and circulate through all
the piping system. After about one hour, drain the system
thoroughly. Wash the interior of the boiler with a hose
inserted through the top tapping. When blow-down water
runs clean, allow boiler to cool, then fill the system with
clean water.
3. Heat the water up to about 180°F and vent air as necessary
to purge the system. The boiler is now ready to operate.
PAGE 10
19A SERIES BOILER
INSTALLATION INSTRUCTIONS
VENT CONNECTION
SERIES 19A BOILER (STEAM)
TAPPING AND CONTROL LOCATIONS
12"
3" SUPPLY TAPS
“A” “B”
ADAPTER COLLAR
( 11 & 12 SECTION ONLY )
“A” - 1" TAP, PRESSURE CONTROLS
“B” - 1 1/4" TAP, STEAM SAFETY VALVE
“C” - 1" TAP, OPTIONAL LWCO
“D” - 3/4" TAP
TOP VIEW
1 1/2" SKIMMER TAP
(1 1/2" TAP, RELIEF VALVE-
11 AND 12 SECTION ONLY)
WATER LEVEL SIGHT
GLASS ASS'Y.
3" SUPPLY TAPS
3"
“A”
4" TAP
JACKET
3/4" TAP STD.
DOMESTIC WATER
HEATER (OPTIONAL)
3/4" TAP OPT.
NORMAL STEAM
WATER LINE
3/4"
VENT
CONN.
3/4"
1" TAP “C”
“D”
“C”
CLEANOUTS
41 1/4"
OPT.
OPTIONAL
INSPECTION
TAPPINGS
1 1/4" OPTIONAL
INSPECTIONTAP
INSP.
TAP.
3" RETURN TAP
FLOOR
3" RETURN TAP
FRONT VIEW
SIDE VIEW
VENT CONNECTION
SERIES 19A BOILER (WATER)
TAPPING AND CONTROL LOCATIONS
12"
3" TAP M.R.H. LIMIT
3" TAP
ADAPTER COLLAR
( 11 & 12 SECTION ONLY )
“A” - 1" TAP, AIR REMOVAL CONN., OPT LWCO
“B” - 1 1/4" TAP, SAFETY VALVE
“A”
“B”
“C” - 1" TAP, OPTIONAL LWCO
“D” - 3/4" TAP, OPER. TEMP. CONN.
TOP VIEW
3" SUPPLY TAPS
THERALTIMER
3"
“A”
4" SUPPLY
JACKET
1 1/2" SKIMMER TAP
3/4" TAP STD.MAN.
RESET HIGH LIMIT
DOMESTIC WATER
HEATER (OPTIONAL)
3/4" TAP OPT.
1/2" TAP
“D”
3/4"
VENT
CONN.
3/4"
1" TAP “C”
“C”
CLEANOUTS
OPTIONAL
INSPECTION
TAPPINGS
1 1/4" OPTIONAL
INSPECTIONTAP
OPT. INSP. TAP.
3" RETURN TAP
3" RETURN TAP
FRONT VIEW
SIDE VIEW
FIGURE 11
PAGE 11
19A SERIES BOILER
INSTALLATION INSTRUCTIONS
WARNING
Any appliance that burns natural gas, propane gas, fuel oil, wood or coal is capable of producing carbon
monoxide (CO).
Carbon Monoxide (CO) is a gas which is odorless, colorless and tasteless but is very toxic.
If your Smith boiler is not working properly, or is not vented properly, dangerous levels of CO may accumu-
late. CO is lighter than air and thus may travel throughout the building. BRIEF EXPOSURE TO HIGH
CONCENTRATIONS OF CO, OR PROLONGED EXPOSURE TO LESSER AMOUNTS OF CO MAY RE-
SULT IN CARBON MONOXIDE POISONING.
EXPOSURE CAN BE FATAL AND EXPOSURE TO HIGH CONCENTRATIONS MAY RESULT IN THE
SUDDEN ONSET OF SYMPTOMS INCLUDING UNCONSCIOUSNESS.
Symptoms of CO poisoning include the following:
dizziness
headaches
nausea
vision problems
loss of muscle control
weakness
shortness of breath
unclear thinking
unconsciousness
The symptoms of CO poisoning are often confused with those of influenza, and the highest incidence of
poisoning occurs at the onset of cold weather or during flu season. A victim may not experience any symp-
toms, only one symptom, or a few symptoms. Suspect the presence of carbon monoxide if symptoms tend to
disappear when you leave your home.
The following signs may indicate the presence of carbon monoxide:
• Hot gases from appliance, venting system, pipes or chimney, escaping into the living space.
• Flames coming out around the appliance.
• Yellow colored flames in the appliance.
• Stale or smelly air.
• The presence of soot or carbon in or around the appliance.
• Very high unexplained humidity inside the building.
If any of the symptoms of CO poisoning occur, or if any of the signs of carbon monoxide are present,
VACATE THE PREMISES IMMEDIATELY AND CONTACT A QUALIFIED HEATING SERVICE COMPANY
OR THE GAS COMPANY OR THE FIRE DEPARTMENT.
To reduce the risk of CO poisoning, have your heating system "tuned up" by a licensed heating contractor or
the gas company -- preferably before each heating season. Also have the service company check your
chimney or vent pipes for blockage.
Your home should also be adequately ventilated, particularly if you have insulated your home.
ONLY QUALIFIED, LICENSED SERVICE CONTRACTORS SHOULD PERFORM WORK
ON YOUR SMITH BOILER.
WARNING
Install, operate and maintain unit in accordance with manufacturer's instructions to avoid exposure to fuel
substances or substances from incomplete combustion which can cause death or serious illness. The State
of California has determined that these substances may cause cancer, birth defects, or other reproductive
harm. Also, install and service this product to avoid exposure to airborne particles of glasswool fibers and/or
ceramic fibers known to the State of California to cause cancer through inhalation.
WESTCAST, INC.
260 NORTH ELM STREET WESTFIELD, MA 01085
TEL. (413) 562-9631 FAX (413) 562-3799
|