Scion PT546 00080 User Manual

Audio System  
TOYOTA PART NO.  
PT546-00080  
Owner’s Manual  
for AM/FM/CD Player with iPod control  
WMA is short for Windows Media  
Audio and refers to an audio com-  
pression technology that is devel-  
oped by Microsoft Corporation.  
WMA data can be encoded by  
using Windows Media Player ver-  
sion 7 or later.  
Windows Media and the Windows  
logo are trademarks or registered  
trademarks of Microsoft Corporation  
in the United States and/or other  
countries.  
Infringement of copyright is legal-  
ly prohibited.  
You are informed about what  
you must or must not do in  
order to reduce the risk of injury  
to yourself and others.  
USE OF CONTROL OR ADJUST-  
MENT OR PERFORMANCE OF PRO-  
CEDURES OTHER THAN THOSE  
SPECIFIED HEREIN MAY RESULT  
IN HAZARDOUS RADIATION EXPO-  
SURE. THE USE OF OPTICAL  
INSTRUMENTS WITH THIS PROD-  
UCT WILL INCREASE EYE HAZARD.  
Important information  
about this manual  
For safety reasons, this manual  
indicates items requiring particular  
attention with the following marks.  
NOTES  
To ensure the correct  
audio system operation  
• Be careful not to spill beverages  
over the audio system.  
• Do not put anything other than a  
Compact Disc into the slot.  
• The use of cellular phones inside  
or near the vehicle may cause  
noise from the audio system  
speakers you are listening to.  
However, this does not indicate a  
malfunction.  
•With some applications  
used to encode WMA files,  
this unit may not operate  
correctly.  
NOTICE  
This is a warning against any-  
thing which may cause dam-  
age to the vehicle or its  
equipment if the warning is  
ignored. You are informed  
about what you must or must  
not do in order to avoid or  
reduce the risk of damage to  
your vehicle and its equipment.  
•With some applications  
used to encode WMA files,  
album names and other text  
information may not be cor-  
rectly displayed.  
About iPod  
• Reproducing and playing back  
non-copyrighted material and  
material that can legally be repro-  
duced and played back for private  
use is permitted with the iPod.  
CAUTION  
This is a warning against any-  
thing which may cause injury to  
people if the warning is ignored.  
3
 
Contents  
4
 
Display and Multi Selector  
Possible MULTI SELECTOR  
operations are indicated.  
Pressing the MULTI SELECTOR up, down,  
left or right enables item selection.  
Turning the MULTI SELECTOR enables  
item selection.  
Pressing the MULTI SELECTOR in the  
center enables item selection.  
5
 
Basic Operation  
Your audio system works when the  
ignition switch is in the ACCor  
ONposition.  
NOTICE  
1POWER  
To avoid draining the battery,  
do not leave the car audio on  
longer than necessary when  
the engine is not running.  
5MUTE  
1 POWER  
Press to turn the unit on or off.  
2 VOLUME/LEVEL + –  
2VOLUME  
3AUDIO CONTROL  
4SSP  
When the Audio Control mode is  
OFF, raises/lowers volume (total vol-  
ume step is 64).  
When the Audio Control mode is ON,  
raises/lowers audio control levels.  
4 SSP is an abbreviation of Scion Sound Processing.  
3 AUDIO CONTROL  
Press and the Audio Control mode  
cycles through the following order:  
SRT (Sound Retouch) = BAS (Bass) =  
TRE (Treble) = FAD (Fader) = BAL  
(Balance) = ASL (Automatic Sound  
Levelizer) = SRT (Sound Retouch)  
6
 
4 SSP (Scion Sound Processing)  
SSP is a modified DSP (Digital Signal  
Processing) system that provides a  
customized sound for your vehicle.  
You can select from the modes  
below.  
SRT : The SRT function provides a wide,  
deep and rich quality to MP3/  
WMA/AAC sound, which gives the  
user a lively impression. You can  
turn the SRT on and off by turning  
the VOLUME knob.  
BAS : Adjust low-pitched tones. The dis-  
play ranges from –5 to 5.  
TRE : Adjust high-pitched tones. The dis-  
play ranges from –5 to 5.  
FAD : Adjust the sound balance between  
the rear and front speakers. The  
display ranges from –R7 to –F7.  
BAL : Adjust the sound balance between  
the left and right speakers. The  
display ranges from –L7 to –R7.  
ASL : During driving, noise in the car  
changes according to the driving  
speed and road conditions. The  
automatic sound levelizer (ASL)  
monitors such varying noise and  
automatically increases the volume  
level. If this noise becomes greater,  
the sensitivity (variation of volume  
level to noise level) of ASL can be  
set to one of three levels. Turning  
the VOLUME knob changes the  
ASL setting as follows:  
NOTICE  
The SRT function can only  
be selected when playing  
MP3/WMA/AAC from CD.  
SSP Neutral : Natural and smooth sound  
that gives no listening  
fatigue but comfort.  
The SRT function does not  
support external com-  
pressed audio media.  
SSP Hear  
: A powerful, energetic,  
“live” sound.  
BAS function and TRE func-  
tion values can be set for  
each of the modes (AM, FM,  
CD/MP3/WMA/AAC, iPod,  
XM Satellite Radio, AUX).  
When you switch modes,  
the settings change to the  
BAS and TRE values set for  
the selected mode.  
SSP Feel  
: Player’s sound —> repro-  
duces the sound on the  
stage that musicians hear.  
For more details, please visit the  
SCION Web site at  
Each time you press it, the SSP  
changes in the following order:  
SSP Neutral = SSP Hear =SSP Feel  
= SSP Neutral  
The ASL function is only  
effective when the vehicle is  
moving.  
5 MUTE  
To reduce the volume instantaneous-  
ly, press the MUTE button.  
will flash on and off.  
MUTE  
Turning the VOLUME knob clock-  
wise  
OFF = Low = Mid = High  
Turning the VOLUME knob coun-  
terclockwise  
To cancel this mode, press the  
MUTE button again.  
High = Mid = Low = OFF  
The initial setting is Low.  
7
Listening to the RADIO  
1 AM•SAT  
4PRESET1-6  
Switches between the AM mode and  
SAT1/2/3 modes. (must have Satellite  
Radio receiver and antenna installed  
at an additional charge to listen to  
Satellite Radio.)  
5SCAN  
2 FM1/2  
Switches between FM1 and FM2  
modes.  
3MULTI SELECTOR  
1AM·SAT  
2FM1/2  
8
 
3 MULTI SELECTOR  
4 PRESET 1-6  
The channel preset in PRESET 1-6  
switches each time you press the  
MULTI SELECTOR in the center.  
Press to recall previously stored sta-  
tions (Preset Channels).  
Press and hold until you hear a beep,  
and the station you are currently  
tuned to is stored as a Preset  
Channel.  
• TUNE <UP>  
Turn the MULTI SELECTOR clock-  
wise or press it to the right to manu-  
ally select (one step at a time) the  
station with the next higher frequen-  
cy.  
NOTICE  
You can store up to 6 stations  
per band.  
When you press the MULTI SELEC-  
TOR up, the next station selects  
automatically. Press the MULTI  
SELECTOR up again, and this will  
stop.  
5 SCAN  
If you press,  
is indicated in  
SCAN  
the display and SCAN begins search-  
ing for stations with good reception.  
If you press and hold until you hear a  
• TUNE <DOWN>  
Turn the MULTI SELECTOR counter-  
clockwise or press it to the left to  
manually select (one step at a time)  
the station with the next lower fre-  
quency.  
beep,  
is indicated in the dis-  
SCAN  
play and SCAN of preset channels  
begins.  
When you press the MULTI SELEC-  
TOR down, the previous station  
selects automatically. Press the  
MULTI SELECTOR down again, and  
this will stop.  
9
Listening to a CD  
NOTICE  
2EJECT  
5Repeat  
67ꢀ  
Never try to disassemble or  
oil any part of the compact  
disc player. Do not insert  
anything except a compact  
disc into the slot.  
8SCAN  
You can load an 8 cm disc  
without using an adaptor.  
Never use an adaptor.  
9TEXT  
3MULTI  
SELECTOR  
Load a CD in the CD slot.  
(
lights.)  
4Random  
1DISC  
10  
 
1 DISC  
6 PRESET 5 (1)  
CAUTION  
Switches to the CD mode. (Only  
effective if a disc is loaded)  
While this is pressed, play of the  
track is reversed. (There is sound.)  
Compact disc players use an  
invisible laser beam which  
could cause hazardous radia-  
tion exposure if directed out-  
side the unit. Be sure to oper-  
ate the player correctly.  
2 EJECT  
7 PRESET 6 (¡)  
Press to eject the disc currently play-  
ing.  
While this is pressed, play of the  
track is fast forwarded. (There is  
sound.)  
3 MULTI SELECTOR  
8 SCAN  
If you press this,  
is indicated  
• TRK <UP>  
in the display and starts to play the  
first 10 seconds of each track on the  
CD being played. Press again to can-  
cel.  
Press the MULTI SELECTOR to the  
right to proceed to the next track.  
• TRK <DOWN>  
Press the MULTI SELECTOR to the  
left takes you back to the start of the  
track currently playing. Press the  
MULTI SELECTOR to the left once  
more to return to the previous track.  
9 TEXT  
Press, and display indications change  
as follows:  
ELAPSED TIME = DISC TITLE = TR  
TITLE (track title)  
When 3 is displayed, if you press  
and hold until you hear a beep, the  
display will change to the next page.  
A maximum of 2 pages (32 charac-  
ters) can be displayed.  
4 PRESET 1 (Random)  
If you press this,  
is indicat-  
ed in the display and starts to play  
tracks on the disc being played in  
random order. Press again to cancel.  
5 PRESET 2 (Repeat)  
If you press this,  
is indicated  
in the display and starts to repeat the  
track being played. Press again to  
cancel.  
11  
Listening to MP3/WMA/  
AAC DISC  
3Repeat  
45ꢀ  
1 MULTI SELECTOR  
• FILE <UP>  
Turn the MULTI SELECTOR clock-  
wise or press it to the right to pro-  
ceed to the next file.  
6SCAN  
7TEXT  
• FILE <DOWN>  
Turn the MULTI SELECTOR counter-  
clockwise or press it to the left takes  
you back to the start of the file cur-  
rently playing. Turn the MULTI  
SELECTOR counterclockwise or  
press it to the left once more to  
return to the previous file.  
1MULTI SELECTOR  
2Random  
• FOLDER <UP>  
Press the MULTI SELECTOR up to  
proceed to the next folder.  
• FOLDER <DOWN>  
Press the MULTI SELECTOR down  
to return to the previous folder.  
Press the MULTI SELECTOR down  
and hold until you hear a beep to  
jump to HOME.  
HOME means returning back to play  
the first file in the first folder on the  
CD being played.  
12  
 
2 PRESET 1 (Random)  
6 SCAN  
NOTICE  
If you press this,  
is indicat-  
If you press this,  
is indicat-  
ed in the display and starts to play  
files in the folder being played in ran-  
dom order. Press again to cancel.  
If you press and hold until you hear a  
ed in the display and starts to play  
the first 10 seconds of each file in  
the folder being played. Press again  
to cancel.  
When playing back a disc  
recorded with the Multi  
Session system, the first ses-  
sion only is played back. If  
the first session combines  
MP3, WMA and AAC files  
and music data (CD-DA), this  
product only plays the music  
data. (Refer to page 34.)  
beep,  
is indicated in the dis-  
If you press and hold until you hear a  
play and starts to play files in all fold-  
ers on the disc being played in ran-  
dom order. Press again to cancel.  
beep,  
is indicated in the dis-  
play and starts to play the first 10  
seconds of the first file of each fold-  
er. Press again to cancel.  
3 PRESET 2 (Repeat)  
7 TEXT  
If you press this,  
is indicated  
in the display and starts to repeat the  
file being played. Press again to cancel.  
If you press and hold until you hear a  
Press and display indications change  
as follows:  
In case of MP3 and AAC:  
ELAPSED TIME = FLD NAME (Folder  
Name) = FILE NAME = ALB TITLE  
(Album Title) = TR TITLE (Track Title)  
= ART NAME (Artist Name)  
beep,  
is indicated in the dis-  
play and starts to repeat the folder  
being played. Press again to cancel.  
In case of WMA:  
4 PRESET 5 (1)  
ELAPSED TIME = FLD NAME (Folder  
Name) = FILE NAME = TR TITLE  
(Track Title) = ART NAME (Artist  
Name)  
When 3 is displayed, if you press  
and hold until you hear a beep, the  
display will change to the next page.  
A maximum of 2 pages (32 charac-  
ters) can be displayed.  
While this is pressed, play of the  
track is reversed. (There is no sound.)  
5 PRESET 6 (¡)  
While this is pressed, play of the  
track is fast forwarded. (There is no  
sound.)  
NOTICE  
With WMA discs, the Album  
Title is not displayed.  
13  
About iPod software version  
About handling the  
iPod  
CAUTION  
The iPod software versions that can  
be used with this unit are as follows  
(operations verified as of November  
2006):  
Store the data into another  
media, to avoid losing the  
data during iPod operation  
with this unit.  
About iPod settings  
This unit supports only an iPod  
featuring the Dock connector  
port.  
iPod (3rd generation)  
iPod (4th generation)  
iPod (5th generation)  
iPod mini  
ver: 2.3.0  
ver: 3.1.1  
ver: 1.2.0  
ver: 1.4.1  
ver: 1.2.1  
ver: 1.2.0  
ver: 1.0.1  
Do not allow direct sunlight  
to fall on the iPod when it is  
not being used. Extended  
exposure to direct sunlight  
can result in iPod malfunc-  
tion due to the resulting  
high temperatures.  
Operations may vary depending  
on the software version of iPod.  
iPod photo  
iPod nano  
You cannot operate the iPod  
Equalizer on products. We recom-  
mend that you set the iPod  
Equalizer to off, before connect-  
ing the iPod to this unit.  
iPod nano (2nd generation)  
iPod shuffle is not supported.  
* Please note that no guarantee applies to  
iPod operations and future updated versions  
of iPod software.  
Do not leave the iPod in  
high temperatures or direct  
sunlight.  
The Shuffle function of the iPod is  
operated as Random on this unit.  
Fix the iPod securely when  
using with this unit. Do not  
let the iPod fall onto the  
floor, where it may become  
jammed under the brake or  
accelerator pedal.  
For details, refer to your iPod  
Owners Manual.  
14  
 
As soon as the iPod is connected,  
its power is automatically turned  
on.  
Connecting the iPod  
Connect the iPod connector.  
NOTICE  
Push in until you hear a click  
to connect firmly. If it does  
not go in smoothly, it may  
be upside down so do not  
force it in as this may result  
in damage.  
While the iPod is connected to this  
Connect the iPod as indicated in the  
figure below using the supplied  
cable.  
unit, SCION (or  
(check mark)) is  
displayed on the iPod.  
Connect the iPod and iPod connect-  
ed is indicated in the display and  
the  
indicator lights.  
iPod with Dock connector port  
Connect the Dock connector  
directly to the iPod with  
Dock connector port. Do not  
connect it via the iPod Dock  
or other connection.  
When the ignition switch is set to  
ACC or ON, the iPod's battery is  
charged while the iPod is con-  
nected to this unit.  
While the iPod is connected to  
this unit, the iPod itself cannot be  
turned on or off.  
The iPod connected to this unit is  
turned off about two minutes  
after the ignition switch is set to  
OFF.  
To the vehicle's  
iPod connector *  
When not using the iPod, be  
sure to attach the dustproof  
cap to the supplied cable  
and store where it does not  
obstruct driving.  
Dock connector 1 ft. 6 in. ( 45 cm )  
When connecting the iPod, remove  
a headphone cable from the iPod.  
* Connection location differs depending on  
the vehicle.  
When the iPod is connected  
to this unit, sound will also  
be heard from the head-  
phone of the iPod. Use with-  
out the headphone.  
NOTICE  
Vehicle type Connection location  
To resolve most problems  
when using your iPod with  
the Scion Audio system, dis-  
connect your iPod from the  
vehicle iPod connection and  
reset it.  
For instructions on how to  
reset your iPod, refer to your  
iPod Owners Manual.  
tC  
Connect to the iPod connector  
in the center console box.  
xB  
xD  
Connect to the iPod connector  
near the parking brake.  
If you install an audio sys-  
tem other than a Scion  
Genuine Audio, you will not  
be able to use the iPod  
adapter.  
Connect to the iPod connector  
near the cup holder.  
15  
 
Disconnecting the  
iPod  
If the iPod does not operate  
with Scion Audio system,  
disconnect the connector  
from the iPod and re-con-  
nect again.  
Remove the iPod connector.  
To reset the iPod, disconnect  
the connector from the iPod,  
and then re-connect to the  
iPod when the operation  
screen displays.  
When disconnecting the iPod  
connector, grasp the part of the  
connector firmly and pull it  
towards you.  
When removing the iPod from this  
unit, the iPod main menu appears  
in the iPod display after a few sec-  
onds.  
Remove the iPod and Bye Bye iPod  
is indicated in the display.  
NOTICE  
Switch to the iPod Direct  
Control after disconnecting  
the iPod.  
16  
 
17  
Listening to songs on  
iPod  
4Repeat  
56ꢀ  
1 AUX•iPod  
Press the button repeatedly until the  
source becomes iPod.  
NOTICE  
7TEXT  
If an iPod is not connected, it  
will not switch to iPod even if  
you press the AUXiPod but-  
ton.  
2MULTI  
SELECTOR  
2 MULTI SELECTOR  
3Random  
8AUDIO CONT  
1AUX·iPod  
• TRK <UP>  
Turn the MULTI SELECTOR clock-  
wise or press it to the right to pro-  
ceed to the next track.  
• TRK <DOWN>  
Turn the MULTI SELECTOR counter-  
clockwise or press it to the left takes  
you back to the start of the track cur-  
rently playing. Turn the MULTI  
SELECTOR counterclockwise or  
press it to the left once more to  
return to the previous track.  
18  
 
• MENU  
3 PRESET 1 (Random)  
7 TEXT  
This calls up the iPod MENU. If you  
first press the MULTI SELECTOR up,  
play lists are displayed. Each time  
you press the MULTI SELECTOR up  
the display changes to one level up  
from the current level.  
If you turn the MULTI SELECTOR  
counterclockwise or clockwise or  
press to the left or right, the MENU  
changes as follows:  
If you press this,  
is indicat-  
Text information recorded on the  
ed in the display and starts to play  
tracks on the iPod being played in  
random order. Press again to cancel.  
After playback finishes of the track  
iPod can be displayed.  
Up to 16 characters can be displayed  
at once.  
Press and display indications change  
as follows:  
ELAPSED TIME = ALB TITLE (Album  
Title) = TR TITLE (Track Title) = ART  
NAME (Artist Name)  
When 3 is displayed, if you press  
and hold until you hear a beep, the  
display will change to the next page.  
A maximum of 2 pages (32 charac-  
ters) can be displayed.  
playing when PRESET  
pressed, random playback begins.  
1
was  
4 PRESET 2 (Repeat)  
If you press this,  
is indicated  
Playlists Artists Albums ꢁ  
Songs  
in the display and starts to repeat  
the track being played. Press again  
to cancel.  
• Category (Sub Menu)  
Each MENU has SUB MENUS called  
Categories that you can call up. If  
you select a MENU and press the  
MULTI SELECTOR in the center, you  
move to one level lower. Each of the  
SUB MENUS has the following lev-  
els:  
• Playlists = List name = Track title  
• Artists = Artists name = Album title  
= Track title  
• Albums = Album title = Track title  
• Songs = Track title  
With each SUB MENU, turning the  
MULTI SELECTOR or pressing it to  
the left or right changes the selected  
item.  
5 PRESET 5 (1)  
8 AUDIO CONT (iPod Direct Control)  
While this is pressed, play of the  
track is reversed.  
Only this track is reversed. (There is  
sound.)  
While the power is in “OFF” posi-  
tion, press and hold the AUDIO  
CONT until the iPodDirect Control  
ON/OFF setting MENU is displayed.  
When you turn the VOLUME knob,  
the setting of the iPodDirect Control  
ON/OFF MENU changes in the fol-  
lowing order:  
6 PRESET 6 (¡)  
While this is pressed, play of the  
track is fast forwarded.  
Only this track is fast forwarded.  
(There is sound.)  
Direct Cont OFF Direct Cont ON  
Direct Cont OFF:You can control iPod  
operations from this unit.  
Direct Cont ON:You can control iPod  
operations on the iPod.  
The “iPodDirect Control ON/OFF set-  
ting Mode” returns to the “PWR  
OFF” after you leave the button for  
6 sec.  
19  
NOTICE  
CAUTION  
Switch to the iPod Direct  
Control after disconnecting  
the iPod.  
This equipment has been tested and found to comply with the lim-  
its for a class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency  
energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communi-  
cations. However, there is no guarantee that interference will not  
occur in a particular installation.  
You cannot use the iPods  
remote control at the same  
time.  
You may hear noise if you  
disconnect during iPod play-  
back.  
This XM tuner supports Audio Services(Music and Talk) of  
*
only XM Satellite Radio and Text Informationlinked to the  
respective Audio Service.  
*Text Informationincludes, Station Name, (Artist) Name, (Song) Title and  
The SCAN operation is not  
availabie when listening to  
the iPod.  
Category Name.  
XM Satellite Radio Inc. is solely responsible for providing ser-  
vices over the air to XM receivers.  
NOTICE  
This XM tuner is awarded a Type Approval Certificate from XM  
Satellite Radio Inc. as a proof of compliance for the services XM  
Satellite Radio provides.  
An additional Genuine Toyota  
satellite receiver and antenna  
must be purchased and installed  
to listen to Satellite radio broad-  
cast in your vehicle.  
20  
How to Subscribe to  
XM Satellite Radio  
<Option>  
Listeners can subscribe by visiting  
XM on the Web at  
XMs Listener Care toll-free at  
(800)852-9696. Customers should  
have their Radio ID ready; the  
Radio ID can be found by selecting  
channel 000 on the radio.  
All fees and programming are the  
responsibility of XM Satellite Radio  
and are subject to change.  
21  
 
Listening to a XM  
Satellite Radio broad-  
cast  
3PRESET1-6  
1 AM•SAT  
4SCAN  
Switches between the AM mode and  
SAT1/2/3 modes. (must have Satellite  
Radio receiver and antenna installed  
at an additional charge to listen to  
Satellite Radio.)  
5TEXT  
2MULTI SELECTOR  
2 MULTI SELECTOR  
The channel preset in PRESET 1-6  
switches each time you press the  
MULTI SELECTOR in the center.  
1AM·SAT  
• TUNE <UP>  
Turn the MULTI SELECTOR clock-  
wise or press it to the right selects  
the next higher channel.  
If you press and hold, you can rapidly  
scroll forward through the channels.  
While displaying Channel Category  
by TYPE UP/DOWN, you can select  
the next channel forward within the  
currently selected type (Channel  
Category) by pressing the MULTI  
SELECTOR to the right.  
22  
 
3 PRESET 1-6  
• TUNE <DOWN>  
NOTICE  
Press to recall previously stored  
channels (Preset Channels).  
Press and hold until you hear a beep,  
and the channel you are currently  
receiving will be stored as a Preset  
Channel.  
Turn the MULTI SELECTOR counter-  
clockwise or press to the left to  
select the previous channel.  
About the display  
Up to a maximum of 16 alphanu-  
meric characters can be displayed.  
(Some information will not be  
fully displayed.)  
If you press and hold, you can rapidly  
scroll down through the channels.  
While displaying Channel Category  
by TYPE UP/DOWN, you can select  
the previous channel within the cur-  
rently selected type (Channel  
Category) by pressing the MULTI  
SELECTOR to the left.  
NOTICE  
You can store up to 6 chan-  
nels per band.  
• TYPE <UP>  
Press the MULTI SELECTOR up to  
see the Channel Category of the  
channel that is currently received.  
When Channel Category is displayed  
(TYPE is indicated), press again to  
switch to the next category.  
4 SCAN  
Press and SCAN of the currently  
selected type (Channel Category)  
starts. At this time,  
ed in the display.  
If you press and hold until you hear a  
beep, SCAN of preset channels  
starts.  
Also at this time,  
in the display.  
is indicat-  
SCAN  
• TYPE <DOWN>  
Press the MULTI SELECTOR down  
to see Channel Category of channel  
that is currently received.  
is indicated  
SCAN  
When Channel Category is displayed  
(TYPE is indicated), press again to  
switch to the previous category.  
5 TEXT  
Press and indication in the display  
changes as follows:  
CH NAME = TITLE (SONG/PROGRAM  
TITLE) = NAME (ARTIST NAME/FEA-  
TURE) = CH NUMBER = CH NAME  
23  
Display the RADIO ID  
NOTICE  
Each XM tuner is identified with a  
unique Radio ID. You will need the  
Radio ID when activating XM ser-  
vice or when reporting a problem.  
If you select another Channel,  
display of the ID Code is can-  
celed.  
Channel (000) alternates the  
display between "RADIO ID"  
and the specific radio ID code.  
How to display RADIO ID  
If you select “CH 000”, the ID Code  
is displayed.  
Select the Channel Number zero  
(000) by turning the MULTI  
SELECTOR or pressing it to the  
left or right.  
The RADIO ID is displayed as 8  
alphanumeric characters.  
(Refer to page 25 to confirm your radio  
ID code)  
Record your ID Code below  
ID CODE ___ ___ ___ ___ ___ ___ ___ ___  
24  
 
Radio ID  
Refer to the corresponding chart to  
verify the Radio ID Code before  
contacting XM Satellite Radio to  
activate your service.  
Corresponding chart  
Display ID  
Display ID  
Display ID  
1
2
3
4
5
6
7
8
9
0
A
B
C
D
E
N
O (Not used.)  
P
Q
R
F (Not used.)  
S(Not used.)  
G
T
H
U
V
W
X
Y
Z
I (Not used.)  
J
K
L
M
25  
Using the AUX  
By inserting a mini plug into the  
AUX adapter, you can listen to  
music from a portable audio device  
through the vehicles speaker sys-  
tem.  
1 AUXiPod  
Switches to the AUX mode.  
CAUTION  
When using a portable audio  
device connected to the  
power outlet or cigarette  
lighter, noise may occur dur-  
ing playback.  
1AUXiPod  
If this happens, use the  
power source of the portable  
audio device.  
26  
 
NOTICE  
If the mini plug of a com-  
mercially available cable  
connected to a portable  
audio or other component is  
not connected to the car  
AUX adapter, the mode will  
not change to the AUX  
mode even if you press the  
AUXiPod button.  
Volume level when playing  
a component connected  
with a mini plug differs to  
that when listening to the  
built-in CD player or radio  
so please make adjust-  
ments.  
If you install an audio sys-  
tem other than a Scion  
Genuine Audio, you will not  
be able to use the AUX  
adapter.  
27  
Changing the  
Opening Screen  
With the main unit switched on  
after pressing the Power button,  
once the key is turned from the  
ACC position to the off position and  
back to ACC again, Scionis dis-  
played as the Opening Screen.  
Users can edit the text themselves  
to make another Opening Screen,  
as an alternate to the default  
Sciondisplay. Up to a maximum  
of 16 characters can be displayed.  
The procedure is described below.  
POWER  
MUTE  
1 Moving to Customize Mode”  
to Enable Editing  
1 With the main unit on, turn the  
key from the ACC position to the  
off position.  
PRESET1  
PRESET3-6  
2 On the main unit, press and hold  
MUTE button then turn the key to  
ACC. The horizontal line in the LCD  
display will start flashing.  
3 Within 15 sec. after confirming  
the horizontal line is flashing, press  
and hold the PRESET 1 button  
then turn the key to OFF position.  
(If 15 sec. elapses before you com-  
plete the button presses, “TIME  
OUT” will be displayed and the  
unit will beep twice. If this occurs,  
repeat the procedure from Step 1).  
This completes shifting to the cus-  
tomize mode.  
28  
 
the text, you can edit from the  
first character.  
3 After you are finished selecting  
the text for the line, press and  
hold down the PRESET 6 button.  
2 Editing the Text  
3 New Message Display  
After completing the shift to cus-  
tomize mode, a flashing cursor  
shows the letter that can be edited by  
selecting a letter starting from “A”.  
The next time the ACC is switched  
on, the text edited by the user will be  
displayed.  
The selected text string is regis-  
tered as the Opening Screen. The  
customize mode ends and the  
registered text string is displayed  
for 6 sec.  
NOTICE  
The letter selection method is  
described below. The time allowed  
for editing is limited to 60 sec.  
1 Press the PRESET 3 or 4 buttons  
to change the flashing letter by  
displaying other letters one by  
one. The letters will change con-  
tinuously if you press and hold the  
PRESET 3 or 4 button.  
To avoid draining the battery,  
do not leave the car audio on  
longer than necessary when  
the engine is not running.  
NOTICE  
If the unit leaves the cus-  
tomize mode during editing,  
repeat procedure 1 from  
Step 2.  
List of the letters and numbers  
that can be selected.  
Upper case letters (A to Z)  
Lower case letters (a to z)  
If the edit is registered with  
no new text, the original  
Opening Screen, Scion,  
will be restored.  
Numbers 0 to 9, spaces, sym-  
bols (!”# and so on)  
2 With the character that you want  
to select displayed, press the  
PRESET 6 button to select it.  
After selecting the character, the  
cursor moves to the right so you  
can edit the next character. After  
you select the 16th character, the  
entire line starts flashing.  
To delete a selected character,  
press the PRESET 5 button. After  
you delete a character the cursor  
shifts left so you can edit the pre-  
vious character. If you delete all of  
29  
Using the Steering  
Controller  
In vehicles equipped with one, you can use the steering controller to operate this product.  
Operation button names and functions  
7 Volume buttons (ª , ·)  
7 Mode selection button (MODE)  
7 Track/station selection button  
(4 , ¢)  
Press ª to raise the volume level.  
Press · to lower the volume level.  
When power to this product is OFF:  
Press the button and power switch-  
es ON.  
When listening to the radio:  
Press the button and the preset  
memory is recalled in order. If you  
continue pressing the button for an  
extended period, automatic station  
selection begins.  
When power to this product is ON:  
Each time you press the button the  
*source changes. If you continue  
pressing the button for an extended  
period, power to this product switch-  
es OFF.  
When listening to a CD:  
Press the button to select a track.  
*The source switches in the follow-  
ing order:  
FM1 = FM2 = CD(MP3/WMA/AAC) =  
(iPod) = (AUX) = AM = (SAT1) =  
(SAT2) = (SAT3) = FM1  
When listeningtoMP3/WMA/AAC:  
Press the button to select a file.  
Press and hold the button to select a  
folder.  
When listening to the iPod:  
Press the button to select a track.  
When listening to a SAT broadcast:  
Press the button to recall preset  
channels in order.  
30  
 
• The maximum number of characters which  
can be displayed for a folder name is 64 .  
• In case of files recorded according to the  
Romeo file system, only the first 64 char-  
acters can be displayed.  
• The folder selection sequence for playback  
and other operations becomes the writing  
sequence used by the writing software.  
For this reason, the expected sequence at  
the time of playback may not coincide with  
the actual playback sequence. However,  
there also is some writing software which  
permits setting of the playback order.  
MP3, WMA and AAC  
files  
MP3 additional infor-  
mation  
• MP3 is short for MPEG Audio Layer 3 and  
refers to an audio compression technology  
standard.  
• Files are compatible with the ID3 Tag Ver.  
1.0, 1.1, 2.2, 2.3 and 2.4 formats for dis-  
play of album (disc title), track (track title),  
artist (track artist) and comments. Ver. 2.x  
of ID3 Tag is given priority when both Ver.  
1.x and Ver. 2.x exist.  
• The emphasis function is valid only when  
MP3 files of 32, 44.1 and 48 kHz frequen-  
cies are played back. (16, 22.05, 24, 32,  
44.1, 48 kHz sampling frequencies can be  
played back.)  
• There is no m3u play list compatibility.  
• There is no compatibility with the MP3i  
(MP3 interactive) or mp3 PRO formats.  
• The sound quality of MP3 files generally  
becomes better with an increased bit  
rates. This unit can play recordings with bit  
rates from 32 kbps to 320 kbps, but in  
order to be able to enjoy sound of a certain  
quality, we recommend using only discs  
recorded with a bit rate of at least 128  
kbps.  
TM  
• WMA is short for Windows Media Audio  
and refers to an audio compression tech-  
nology that is developed by Microsoft  
Corporation. WMA data can be encoded  
by using Windows Media Player version 7  
or later.  
• AAC is short for Advanced Audio Coding  
and refers to an audio compression tech-  
nology standard.  
• With some applications used to encode  
WMA files, this unit may not operate cor-  
rectly.  
• With some applications used to encode  
WMA files, album names and other text  
information may not be correctly dis-  
played.  
• This unit allows playback of MP3/WMA/AAC  
files on CD-ROM, CD-R and CD-RW discs.  
Disc recordings compatible with level 1  
and level 2 of ISO9660 and with the  
Romeo and Joliet file system can be  
played back.  
• MP3/WMA/AAC files are not compatible  
with packet write data transfer.  
• The maximum number of characters which  
can be displayed for a file name, including  
the extension (.mp3, .wma, .m4a), is 64 ,  
from the first character.  
IMPORTANT  
When naming an MP3/  
WMA/AAC file, add the cor-  
responding filename exten-  
sion (.mp3, .wma, .m4a).  
This unit plays back files  
with the filename extension  
(.mp3, .wma, .m4a) as an  
MP3/WMA/AAC file. To pre-  
vent noise and malfunc-  
tions, do not use these  
extensions for files other than  
MP3/WMA/AAC files.  
31  
 
WMA additional infor- AAC additional infor- About folders and  
mation  
mation  
MP3/WMA/AAC files  
• This unit plays back WMA files encoded by  
Windows Media Player version 7, 7.1, 8, 9  
and 10.  
• You can only play back WMA files in the  
frequencies 32, 44.1 and 48 kHz.  
• This unit plays back AAC files encoded by  
• An outline of a CD-ROM with MP3/WMA/AAC  
files on it is shown below. Subfolders are  
shown as folders in the folder currently  
selected.  
iTunes® version 4.8 and earlier.  
• This unit plays back AAC files in the sam-  
pling frequencies 11.025, 16, 22.05, 24, 32,  
44.1 and 48 kHz.  
01  
• The sound quality of WMA files generally  
becomes better with an increased bit rate.  
This unit can play recordings with bit rates  
from 48 kbps to 320 kbps (CBR) or from  
48 kbps to 384 kbps (VBR), but in order to  
be able to enjoy sound of a certain quality,  
we recommend using discs recorded with  
a higher bit rate.  
• The sound quality of AAC files generally  
becomes better with an increased trans-  
mission rate. This unit can play recordings  
with transmission rates from 16kbps to  
320kbps,but in order to be able to enjoy  
sound of a certain quality, we recommend  
using discs recorded with a higher trans-  
mission rate.  
(ROOT)  
02  
001.mp3  
(001.wma, 001.m4a)  
010.mp3  
(010.wma, 010.m4a)  
03  
011.mp3  
(011.wma, 011.m4a)  
• This unit doesn’t support the following for-  
mats.  
Windows Media Audio 9 Professional(5.1ch)  
• This unit doesn’t support the following for-  
mats.  
- Apple Lossless  
020.mp3  
(020.wma, 020.m4a)  
04  
021.mp3  
(021.wma, 021.m4a)  
Windows Media Audio 9 Lossless  
Windows Media Audio 9 Voice  
030.mp3  
(030.wma, 030.m4a)  
05  
First Second Third  
level level  
level  
32  
   
NOTES  
This unit assigns folder  
number. The user can not  
assign folder numbers.  
It is not possible to check  
folders that do not include  
MP3/WMA/AAC files. (These  
folders will be skipped with-  
out displaying the folder  
number.)  
MP3/WMA/AAC files in up  
to 8 tiers of folders can be  
played back. However, there  
is a delay in the start of  
playback on discs with  
numerous tiers. For this rea-  
son we recommend creating  
discs with no more than 2  
tiers.  
It is possible to play back up  
to 192 folders on one disc.  
33  
ID3 Tag  
m3u  
Terms  
This is a method of embedding track-  
Playlists created using the  
related information in a MP3 file. This  
embedded information can include  
the track title, the artist’s name, the  
album title, the music genre, the year  
of production, comments and other  
data. The contents can be freely edit-  
ed using software with ID3 Tag edit-  
ing functions. Although the tags are  
restricted to the number of charac-  
ters, the information can be viewed  
when the track is played back.  
“WINAMP” software have a playlist  
file extension (.m3u).  
Packet write  
This is a general term for a method  
MP3  
of writing on CD-R, etc. at the time  
required for a file, just as is done  
with files on floppy or hard discs.  
MP3 is short for MPEG1 & 2 Audio  
Layer3. It is an audio compression  
standard set by a working group  
(MPEG) of the ISO (International  
Standards Organization). MP3 is able  
to compress audio data to about 1/10  
the level of a conventional disc.  
Bit rate  
This expresses data volume per sec-  
ond, or bps units (bits per second).  
The higher the rate, the more infor-  
mation is available to reproduce the  
sound. Using the same encoding  
method (such as MP3), the higher  
the rate, the better the sound.  
WMA  
ISO9660 format  
TM  
WMA is short for Windows Media  
This is the international standard for  
the format logic of CD-ROM folders  
and files. For the ISO9660 format,  
there are regulations for the follow-  
ing two levels.  
Audio and refers to an audio com-  
pression technology that is developed  
by Microsoft Corporation. WMA data  
can be encoded by using Windows  
Media Player version 7 or later.  
Multi-session  
Multi-session is a recording method  
that allows additional data to be  
recorded later. When recording data  
on a CD-ROM, CD-R or CD-RW, etc.,  
all data from beginning to end is  
treated as a single unit or session.  
Multi-session is a method of record-  
ing more than 2 sessions in one disc.  
Level 1:  
Microsoft, Windows Media, and the  
Windows logo are trademarks, or  
registered trademarks of Microsoft  
Corporation in the United States and/  
or other countries.  
The file name is in 8.3 format (the name  
consists of up to 8 characters, half-byte  
English capital letters and half-byte  
numerals and the “_” sign, with a file-  
extension of three characters).  
Level 2:  
The file name can have up to 31 charac-  
ters (including the separation mark “.”  
and a file extension). Each folder contains  
less than 8 hierarchies.  
AAC  
CD-DA  
AAC is short for Advanced Audio  
Coding and refers to an audio com-  
pression technology standard used  
with MPEG2 and MPEG4.  
CD-DA is an abbreviation of Compact  
Disc Digital Audio. It refers to the  
uncompressed format of regular  
CDs.  
Extended formats  
Joliet:  
File names can have up to 64 characters.  
Romeo:  
File names can have up to 128 characters.  
34  
 
• To clean a CD, wipe the disc with a soft  
cloth outward from the center.  
• Playback of discs recorded on a person-  
al computer may not be possible,  
depending on the application settings  
and the environment. Please record  
with the correct format. (For details,  
contact the manufacturer of the appli-  
cation.)  
CD player and care  
• Use only CDs that have either of the  
two Compact Disc Digital Audio marks  
as shown below.  
• If the heater is used in cold weather,  
moisture may form on components  
inside the CD player. Condensation  
may cause the CD player to malfunc-  
tion. If you think that condensation is a  
problem, turn off the CD player for an  
hour or so to allow it to dry out and  
wipe any damp discs with a soft cloth  
to remove the moisture.  
• Playback of CD-R/CD-RW discs may  
become impossible in case of direct  
exposure to sunlight, high tempera-  
tures, or the storage conditions in the  
car.  
• Titles and other text information record-  
ed on a CD-R/CD-RW disc may not be  
displayed by this unit (in the case of  
audio data (CD-DA)).  
• Use only normal, round CDs. If you  
insert irregular, non-round, shaped CDs  
they may jam in the CD player or not  
play properly.  
• Road shocks may interrupt CD play-  
back.  
• Never put a label, tape or scratches on  
a disc. These will prevent the disc from  
being played.  
• This unit conforms to the track skip  
function of the CD-R/CD-RW disc. The  
tracks containing the track skip informa-  
tion are skipped automatically (in case  
of audio data (CD-DA)).  
• Check all CDs for cracks, scratches or  
warping before playing. CDs that have  
cracks, scratches or are warped may  
not play properly. Do not use such  
discs.  
• Avoid touching the recorded (non-print-  
ed) surface when handling the disc.  
• Store discs in their cases when not in  
use.  
• Keep discs out of direct sunlight and do  
not expose the discs to high tempera-  
tures.  
• Do not attach labels, write on or apply  
chemicals to the surface of the discs.  
• If you insert a CD-RW disc into this  
unit, time to playback will be longer  
than when you insert a conventional  
CD or CD-R disc.  
• Read the precautions accompanying  
the CD-R/CD-RW discs before use.  
• Recordings on CD-R/CD-RW can not be  
played back using the DDCD (Double  
Density CD) system.  
CD-R and CD-RW discs  
• When CD-R/CD-RW discs are used,  
playback is possible only for discs  
which have been finalized.  
• It may not be possible to play back CD-  
R/CD-RW discs recorded on a music  
CD recorder or a personal computer  
because of disc characteristics, scratch-  
es or dirt on the disc, or dirt, condensa-  
tion, etc,. on the lens of this unit.  
• This unit will not play back SACD  
(Super Audio CD).  
35  
 
Error indications  
If the CD player does not work, the CD stops suddenly during playback, or a similar problem occurs, an error indi-  
cation will appear on the display. The cause of the trouble will be indicated by an error number, and you should  
check the corresponding item shown in the table below.  
When the disc is dirty or has been inserted upside-down.  
Check the disc.  
ERROR 1  
There is probably an electrical or mechanical fault in the CD player.  
Contact your Scion dealer and ask for repair.  
ERROR 3  
This appears when there is excess current flow.  
Contact your Scion dealer and ask for repair.  
ERROR 4  
This appears when the CD player does not work because its temperature is high.  
Wait a short while until the vehicle temperature goes down.  
WAIT  
This appears when an MP3/WMA/AAC file format is unusual and not supported by  
this unit like WAV format recordings.  
Please check the MP3/WMA/AAC file format.  
NO MUSIC  
36  
 
When problems occur while the iPod is connected to this unit, a message will appear on the display. Refer to the  
table below to identify the problem, then take the suggested corrective action.  
Old version of iPod.  
Update the version of iPod.  
UPDATE YOUR iPod  
Communication failure.  
Disconnect the cable from iPod. Once iPod main menu appears in the iPod display,  
connect the cable again.  
Reset the iPod.  
iPod COMM. ERROR  
iPod charge voltage is not normal.  
Disconnect the cable from iPod.  
Once iPod main menu appears in the iPod display, connect the cable again.  
Check that there is no foreign substance etc. on the connected part of the connec-  
tor.  
iPodCHARGE ERROR  
No songs.  
Transfer the songs to iPod.  
iPod NO SONGS  
No songs in the current Playlist.  
Select a list that contains the songs.  
Empty Playlist  
37  
When problems occur with the XM tuner, a message will appear on the display. Refer to the table below to identi-  
fy the problem, then take the suggested corrective action.  
The XM antenna is not connected.  
Check whether the XM antenna cable is attached securely.  
CHECK ANTENNA  
A short-circuit occurring in the antenna or the surrounding antenna cable.  
Make sure that there is nothing unusual with the antenna or antenna cable.  
You have not subscribed to XM. Radio is being updated with latest encryption code.  
Contact XM Satellite Radio for subscription information. When a contract is canceled  
you can choose CH000 and all free-to-air channels.  
Premium channel you selected is not authorized.  
Wait approximately 2 seconds until the radio returns to the previous channel or CH001.  
If it doesn't change automatically, select another channel.  
UPDATING  
If you want to listen to the premium channel, please contact XM.  
XM signal is too weak at the current location.  
Wait until your vehicle reaches a location with a stronger signal.  
NO SIGNAL  
Unit is acquiring audio or program information.  
LOADING  
Wait until the unit has received the information.  
The channel you selected is not broadcasting any programming.  
OFF AIR  
Select another channel.  
The XM Listener Care Center is also available on the phone, please call (800)-967-2346 during the following hours:  
Mon - Sat: 6 AM - 2 AM EST Sun: 8 AM - 8 PM EST  
38  
AM tuner  
Changing or discon-  
necting your battery  
Specifications  
Frequency range  
. . . . . . . . . .530 kHz to 1 710 kHz (10 kHz)  
General  
Power source . . . . . . . . . . . . . 13.2 V DC  
(10.5 V to 16.0 V allowable)  
FM tuner  
Frequency range  
. . . . . . . . . . . . . 87.75 MHz to 107.9 MHz  
When you purchase a vehicle, your  
dealer sets the Equalizer for the vehi-  
cle type.  
Remember that when you change or  
disconnect your battery, the Equalizer  
settings return to the tC factory set-  
tings.  
Grounding system . . . . . . Negative type  
Max. current consumption . . . . . . . 15 A  
Dimensions ( W × H × D )  
. . . . . . . . . . . . . . . . 200 × 100 × 165 mm  
Weight . . . . . . . . . . . . . . . . . . . . . . 2.0 kg  
If this happens, it is recommended  
you set the Equalizer for the type of  
vehicle you purchased. For more  
details, please contact your nearest  
SCION dealer.  
Audio  
Tone controls  
(Bass) . . . . . . . . . . . . Frequency : 80 Hz  
Level : 10 dB  
(Treble) . . . . . . . . . . Frequency : 10 kHz  
Level : 10 dB  
Maximum power output . . . . . . 40 W × 4  
Load impedance . . . . . . . . . . . . . . . . 4  
Changing the vehicle type Equalizer  
setting  
Press and hold the SSP button until  
you hear a beep, and the current  
Equalizer setting is displayed. Turn  
the VOLUME knob to change the  
vehicle type.  
CD player  
System . . . . Compact disc audio system  
Usable discs . . . . . . . . . . . Compact disc  
Signal format  
Sampling frequency . . . . . . . . 44.1 kHz  
Number of quantization bits  
. . . . . . . . . . . . . . . . . . . . . . . . 16; linear  
Number of channels . . . . . . . . 2 (stereo)  
MP3 decoding format  
FIX-Equalizer mode changes as fol-  
lows:  
Car Type tC = Car Type xB = Car Type xD  
If the battery is changed or discon-  
nected, the ASL setup option is not  
displayed in the AUDIO CONTROL  
menu until the vehicle is moving.  
. . . . . . . . . . . MPEG1 & 2 Audio Layer 3  
WMA decoding format  
. . . . . . . . . Ver.7, 7.1, 8, 9, 9.1(2ch audio)  
AAC decoding format  
. . . iTunes® 6.2 or less (extension* .m4a)  
39  
 
< KNKZX > < 06K00000 > < DEH-M8027ZT >  
< YRB5043-A/U > UC  
40  

West Bend Blender 3000 User Manual
Toshiba MA 216 User Manual
Toastmaster RRFP1 User Manual
Toastess Classic Power TBL634 User Manual
Sony TC WE725 User Manual
Sony DSR200P User Manual
Sony DSCT300B User Manual
Sony Cassette Player XR 4803 User Manual
Sony BDV T58 User Manual
Sanyo Car Satellite TV System HT30744 User Manual