3-278-987-12(1)
Digital HD Video Camera Recorder
Operating Guide
HDR-HC9
© 2008 Sony Corporation
long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system.
This will prevent damage to the set due to
lightning and power-line surges.
Cleaning
Unplug the set from the wall outlet before
cleaning or polishing it. Do not use liquid cleaners
or aerosol cleaners. Use a cloth lightly dampened
with water for cleaning the exterior of the set.
Service
Installation
Damage Requiring Service
Unplug the set from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
– When the power cord or plug is damaged or
frayed.
– If liquid has been spilled or objects have fallen
into the set.
– If the set has been exposed to rain or water.
– If the set has been subject to excessive shock by
being dropped, or the cabinet has been
damaged.
– If the set does not operate normally when
following the operating instructions. Adjust
only those controls that are specified in the
operating instructions. Improper adjustment of
other controls may result in damage and will
often require extensive work by a qualified
technician to restore the set to normal operation.
Water and Moisture
Do not use power-line operated sets near water –
for example, near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool, etc.
Power-Cord Protection
Route the power cord so that it is not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to the
plugs, receptacles, and the point where the cord
exits from the appliance.
Accessories
Do not place the set on an unstable cart, stand,
tripod, bracket, or table. The set may fall, causing
serious injury to a child or an adult, and serious
damage to the set. Use only a cart, stand, tripod,
bracket, or table recommended by the
manufacturer.
– When the set exhibits a distinct change in
performance – this indicates a need for service.
Servicing
Ventilation
Do not attempt to service the set yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards.
The slots and openings in the cabinet are provided
for necessary ventilation. To ensure reliable
operation of the set, and to protect it from
overheating, these slots and openings must never
be blocked or covered.
– Never cover the slots and openings with a cloth
or other materials.
– Never block the slots and openings by placing
the set on a bed, sofa, rug, or other similar
surface.
Refer all servicing to qualified service personnel.
Replacement parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer that have the same
characteristics as the original parts.
– Never place the set in a confined space, such as
a bookcase, or built-in cabinet, unless proper
ventilation is provided.
– Do not place the set near or over a radiator or
heat register, or where it is exposed to direct
sunlight.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
Safety Check
Upon completion of any service or repairs to the
set, ask the service technician to perform routine
safety checks (as specified by the manufacturer)
to determine that the set is in safe operating
condition.
Lightning
For added protection for this set during a lightning
storm, or when it is left unattended and unused for
3
Read this first
Before operating the unit, please read this
manual thoroughly, and retain it for future
reference.
Owner’s Record
The model and serial numbers are located on the
bottom. Record the serial number in the space
provided below. Refer to these numbers whenever
you call your Sony dealer regarding this product.
WARNING
Model No. HDR-HC9
Serial No.
Do not expose the batteries to
excessive heat such as sunshine,
fire or the like.
Model No. AC-
Serial No.
Excessive sound pressure from
earphones and headphones can
cause hearing loss.
For customers in the U.S.A.
If you have any questions about this
product, you may call:
Sony Customer Information Center 1-800-
222-SONY (7669).
The number below is for the FCC related
matters only.
CAUTION
Replace the battery with the
specified type only. Otherwise, fire
or injury may result.
Regulatory Information
For customers in the U.S.A. and
CANADA
Declaration of Conformity
Trade Name: SONY
Model No.: HDR-HC9
RECYCLING LITHIUM-ION BATTERIES
Lithium-Ion batteries are recyclable.
Responsible Party: Sony Electronics Inc.
You can help preserve our
environment by returning your
used rechargeable batteries to the
collection and recycling location
nearest you.
For more information regarding
recycling of rechargeable batteries, call toll free 1-
800-822- 8837, or visit http://www.rbrc.org/
Address: 16530 Via Esprillo, San Diego, CA
92127 U.S.A.
Telephone number: 858-942-2230
This device complies with Part 15 of the FCC
Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference
that may cause undesired operation.
Caution: Do not handle damaged or leaking
Lithium-Ion batteries.
Battery pack
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
Notes
HDR-HC9 is to be used with AC Adaptor Model
AC-L200/L200B.
(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
This Class B digital apparatus complies with
Canadian ICES-003.
4
Note
Notes on use
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
Your camcorder is supplied with two
kinds of manuals
– “Operating Guide” (This manual)
– “First Step Guide” for using your
camcorder while connected to a computer
(stored on the supplied CD-ROM)
Type of cassette you can use in your
camcorder
You can use mini DV cassettes marked
with
. Your camcorder is not
compatible with the Cassette Memory
function (p. 91).
Types of “Memory Stick” you can use
in your camcorder
You can use “Memory Stick” that have the
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
–
–
(“Memory Stick Duo”)
(“Memory Stick
PRO Duo”)
The supplied interface cable must be used with the
equipment in order to comply with the limits for a
digital device pursuant to Subpart B of Part 15 of
FCC Rules.
–
(“Memory Stick
PRO-HG Duo”)
“Memory Stick Duo”
(This size can be used with your
camcorder.)
For the State of California, USA only
Perchlorate Material - special handling may
apply, See
www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material: Lithium battery contains
perchlorate.
“Memory Stick”
(You cannot use with your camcorder.)
• You cannot use any type of memory card
except “Memory Stick Duo.”
• “Memory Stick PRO Duo” can be used
only with “Memory Stick PRO”
compatible equipment.
Continued ,
5
Read this first (Continued)
• Do not attach a label or the like on a
“Memory Stick Duo” or a Memory Stick
Duo adaptor.
black points and/or bright points (white,
red, blue, or green in color) that appear
constantly on the LCD screen and the
viewfinder. These points are normal
results of the manufacturing process and
do not affect the recording in any way.
When using a “Memory Stick Duo”
with “Memory Stick” compatible
equipment
Be sure to insert the “Memory Stick Duo”
into the Memory Stick Duo Adaptor.
Memory Stick Duo Adaptor
Black point
Using the camcorder
• Do not hold the camcorder by the
following parts.
White, red, blue
or green point
• Exposing the LCD screen, the viewfinder,
or the lens to direct sunlight for long
periods of time may cause malfunctions.
• Do not aim at the sun. Doing so might
cause your camcorder to malfunction.
Take pictures of the sun only in low light
conditions, such as at dusk.
Viewfinder
LCD panel
• The camcorder is not dustproof, dripproof
or waterproof.
• When connecting your camcorder to
another device with communication
cables, be sure to insert the connector plug
in the correct way.
About changing the language setting
The on-screen displays in each local
language are used for illustrating the
operating procedures. Change the screen
language before using your camcorder if
necessary (p. 17).
Pushing the plug forcibly into the terminal
will damage the terminal and may result
in a malfunction of your camcorder.
On recording
• Before starting to record, test the
recording function to make sure the
picture and sound are recorded without
any problems.
• Compensation for the contents of
recordings cannot be provided, even if
recording or playback is not possible due
to a malfunction of the camcorder, storage
media, etc.
About menu items, LCD panel,
viewfinder, and lens
• A menu item that is grayed out is not
available under the current recording or
playback conditions.
• The LCD screen and the viewfinder are
manufactured using extremely high-
precision technology, so over 99.99% of
the pixels are operational for effective
use. However, there may be some tiny
• TV color systems differ depending on the
country/region. To view your recordings
6
on a TV, you need an NTSC system-based
TV.
• Television programs, films, video tapes,
and other materials may be copyrighted.
Unauthorized recording of such materials
may be contrary to the copyright laws.
On playing back HDV tapes on other
devices
You cannot play back a tape recorded in the
HDV format on DV format video cameras
or on mini DV players (The screen appears
blue).
Check the contents of tapes by playing
them back on this camcorder prior to
playing them back on other devices.
About this manual
• The images of the LCD screen and the
viewfinder used in this manual for
illustration purposes are captured using a
digital still camera, and therefore may
appear different.
• Design and specifications of recording
media and other accessories are subject to
change without notice.
About the Carl Zeiss lens
Your camcorder is equipped with a Carl
Zeiss lens, which was developed jointly by
Carl Zeiss, in Germany, and Sony
Corporation, and produces superior images.
It adopts the MTF measurement system for
video cameras and offers a quality typical
of a Carl Zeiss lens. Also, the lens for your
camcorder is T -coated to suppress
unwanted reflections and faithfully
reproduce colors.
MTF= Modulation Transfer Function
The number value indicates the amount of
light from a subject coming into the lens.
7
Note on the icons used in this manual
Table of Contents
Features available for the HDV format only
Features available for the DV format only
................................................... 32
.................................................... 12
................................................... 35
................................................... 36
.................................................... 13
Easy Recording/Playback
(Easy Handycam) ....................... 21
................................................... 25
................................................... 26
8
Spanish Quick Guide/
Marking images on the “Memory Stick
9
Enjoying pictures with high definition quality
Trying out the HDV format!
Shooting in the HDV format
High image quality
Being HDV format compliant, your camcorder is ready to shoot crystal clear, high-definition
images.
What is the HDV format?
The HDV format is a video format for shooting and playing back high definition images on
popular DV standard cassette tapes.
• Your camcorder adopts the HDV1080i
specification, which utilizes 1,080 effective
scanning lines, within the HDV standards, and
records pictures at the image bit rate of about 25 Mbps.
1,080 effective
scanning lines
• These operating instructions refer to the HDV1080i specification as HDV format unless there is a need
to specify.
Why shoot in the HDV format?
With the global standard moving to the digital video format, you can record important
moments in HDV format to keep high quality images for the future.
Your camcorder’s down convert function converts pictures in HDV format to SD (standard
definition) image quality for viewing on older wide TV formats, and on 4:3 aspect ratio TVs
when a high definition TV set is not available. This provides an easy path to HDV format
video.
• The down convert function converts HDV format video to DV for playback or editing when your
camcorder is connected to a TV or VCR that is not HDV1080i compliant. The resulting image is
displayed in SD (standard definition).
10
Viewing video recorded in the HDV format!
Pictures recorded in the HDV format can be played back as crisp HD (high definition)
pictures on a high definition TV.
• For details on HDV1080i compliant TVs, see page 34.
Your camcorder can down convert video recorded in the HDV format to SD (standard
definition) image quality for playback on a conventional TV.
Connecting to an HDV1080i device
A supplied i.LINK cable allows you to copy pictures in HD (high definition) image quality.
Connecting to an HDV1080i non-compliant device
Your camcorder can down convert HDV format video to SD (standard definition) image
quality to enable copying.
Using the supplied software, you can import movies from a tape or still images from a
“Memory Stick Duo” to the computer. You can also edit the imported movies and create a
DVD-video in SD (standard definition) image quality.
11
GSetttiengpSta1rte:d Checking supplied items
USB cable (1) (p. 71)
Make sure that you have following items
supplied with your camcorder.
The number in the parentheses indicates the
number of that item supplied.
AC Adaptor (1) (p. 13)
Rechargeable battery pack NP-FH60 (1)
Lens hood (1) (p. 105)
Wireless Remote Commander (1)
Remove the lens hood when you use the
flash, Nightshot or SuperNightshot, or its
shadow will appear in the picture.
A button-type lithium battery is already installed.
CD-ROM “Handycam Application
Software” (1) (p. 75)
Operating Guide (This manual) (1)
Component video cable (1) (p. 34)
12
Step 2: Charging the battery pack
2
POWER
switch
1
DC IN jack
3
4
Battery pack
DC plug
/CHG
(charge)
lamp
4
To the wall outlet
AC Adaptor
(wall socket)
Power cord (Mains lead)
You can charge the “InfoLITHIUM”
4
Connect the power cord (mains
lead) to the AC Adaptor and the
wall outlet (wall socket).
battery pack (H series) (p. 93) after
attaching it to your camcorder.
b Notes
The /CHG (charge) lamp lights up and
charging starts. The /CHG (charge)
lamp turns off when the battery is fully
charged.
• You cannot attach any “InfoLITHIUM” battery
pack other than the H series to your camcorder.
1
Attach the battery pack to your
camcorder.
b Notes
Attach the battery pack by sliding it in
the direction of the arrow until it clicks.
• Disconnect the AC Adaptor from the DC IN
jack holding both the camcorder and the DC
plug.
z Tips
2
3
Slide the POWER switch to OFF
(CHG) (the default setting).
• You can operate your camcorder connected to a
power source such as a wall outlet (wall socket)
as shown in the illustration. The battery pack
will not lose its charge in this case.
Connect the AC Adaptor to the
DC IN jack of your camcorder. Be
sure that the v mark on the DC
plug is facing to the v mark on
your camcorder.
Continued ,
13
Step2: Charging the battery pack (Continued)
To remove the battery pack
Remaining battery (approx.)
Slide the POWER switch to OFF (CHG).
Slide the BATT (battery release) lever and
remove the battery pack.
60
65
Recording capacity (approx.)
You can check the remaining battery charge
on the LCD screen.
Indicator
Status
BATT (battery
release) lever
Sufficient power remaining
Battery low, recording/
playback will stop soon.
Replace the battery with a
fully charged one, or charge
the battery.
When storing the battery pack
Fully discharge the battery before storing it
Charging time
Approximate time (min.) required when
you fully charge a fully discharged battery
pack.
To check the remaining battery
(Battery Info)
Set the POWER switch to OFF (CHG), then
press DISPLAY/BATT INFO.
Battery pack
NP-FH50
Charging time
135
135
170
390
NP-FH60 (supplied)
NP-FH70
DISPLAY/
BATT INFO
NP-FH100
Recording time
Approximate time (min.) available when
you use a fully charged battery pack.
After a while, the approximate recordable
time and battery information appear for
about 7 seconds. You can view the battery
information for up to 20 seconds by
pressing DISPLAY/BATT INFO again
while the information is displayed.
Continuous Typical
Battery pack
recording
time
recording
time*
Recording
Format
HDV DV HDV DV
NP-FH50
70
70
75
70 40
75 40
80 40
40
40
45
14
• The /CHG (charge) lamp flashes during
charging, or Battery Info (p. 14) will not be
correctly displayed under the following
conditions.
– The battery pack is not attached correctly.
– The battery pack is damaged.
Continuous Typical
Battery pack
recording
time
recording
time*
Recording
Format
HDV DV HDV DV
NP-FH60
(supplied)
90
95 50
50
55
55
85
90
90
– The battery pack is worn-out (for Battery Info
only).
95 100 50
100 105 55
150 155 80
155 165 85
160 170 85
• The power will not be supplied from the battery
as long as the AC Adaptor is connected to the
DC IN jack of your camcorder, even when the
power cord (mains lead) is disconnected from
the wall outlet (wall socket).
• When attaching an optional video light, it is
recommended that you use an NP-FH70 or NP-
FH100 battery pack.
NP-FH70
NP-FH100
345 365 185 195
365 385 195 210
375 395 205 215
On the charging/recording/playback time
• Times measured with the camcorder at 25 °C
(77 °F) (10 to 30 °C (50 °F to 86 °F) is
recommended).
• The recording and playback time will be shorter
when you use your camcorder in low
temperatures.
• The recording and playback time will be shorter
depending on the conditions under which you
use your camcorder.
* Typical recording time shows the time when
you repeat recording start/stop, turning the
power on/off and zooming.
b Notes
• All times measured under the following
conditions:
Top: When the LCD backlight turns on.
Middle: When the LCD backlight turns off.
Bottom: Recording with the viewfinder while
the LCD panel is closed.
On the AC Adaptor
• Use the nearby wall outlet (wall socket) when
using the AC Adaptor. Disconnect the AC
Adaptor from the wall outlet (wall socket)
immediately if any malfunction occurs while
using your camcorder.
Playing time
Approximate time (min.) available when
you use a fully charged battery pack.
• Do not use the AC Adaptor placed in a narrow
space, such as between a wall and furniture.
• Do not short-circuit the DC plug of the AC
Adaptor or battery terminal with any metallic
objects. This may cause a malfunction.
• Even if your camcorder is turned off, AC power
(house current) is still supplied to it while
connected to the wall outlet (wall socket) via the
AC Adaptor.
LCD panel LCD panel
Battery pack
opened*
closed
Recorded
Format
HDV DV HDV DV
105 115 120 130
140 150 160 170
NP-FH50
NP-FH60
(supplied)
NP-FH70
230 245 255 280
525 565 590 635
NP-FH100
* When the LCD backlight turns on.
On the battery pack
• Before changing the battery pack, slide the
POWER switch to OFF (CHG).
15
Step 3: Turning the
power on and setting
the date and time
Set the date and time when using this
camcorder for the first time. If you do not
set the date and time, the [CLOCK SET]
screen appears every time you turn on your
camcorder or change the POWER switch
position.
3
4
Move to [M] (month) with
then set with
,
/
.
Move to [D] (day) with
set with
, then
/
and repeat for the
hour and minute.
For midnight, set it to 12:00 AM.
For midday, set it to 12:00 PM.
5
Make sure the date and time
settings are correct, then touch
.
POWER switch
Touch the button on
The clock starts.
the LCD screen.
To turn off the power
Slide the POWER switch to OFF (CHG).
1
While pressing the green button,
slide the POWER switch in the
direction of the arrow to turn on
the respective lamp.
To reset the date and time
You can set the desired date and time by
touching
t
/
t [CLOCK
CAMERA-TAPE: To record on a tape.
CAMERA-MEMORY: To record on a
“Memory Stick Duo.”
b Notes
• If you do not use your camcorder for about 3
months, the built-in rechargeable battery gets
discharged and the date and time settings may
be cleared from the memory. In that case,
charge the rechargeable battery and then set the
PLAY/EDIT: To play or edit pictures.
The [CLOCK SET] screen appears.
–:––:––
CLOCK SET
• At the time of purchase, the power is set to turn
off automatically if you leave your camcorder
without any operation attempted for
Y
M
2008 JAN 1 12:00AM
D
approximately 5 minutes, to save battery power
OK
z Tips
2
Set [Y] (year) with
/
.
• The date and time are not displayed while
recording, but they are automatically recorded
on the tape, and can be displayed during
(During Easy Handycam operation, you can set
only [DATE/TIME])).
You can set any year up to the year
2079.
16
• The lens cover opens automatically when the
POWER switch is set to CAMERA-TAPE or
CAMERA-MEMORY.
• If the buttons on the touch panel do not work
correctly, adjust the touch panel
Changing the language setting
You can change the on-screen displays to
show messages in a specified language.
Touch
t [MENU] t
(TIME/
LANGU.) t [LANGUAGE], then select
the desired language.
17
Step 4: Making setting adjustments before
recording
The LCD panel
The viewfinder
Open the LCD panel 90 degrees to the
camcorder (1), then rotate it to the best
angle to record or play (2).
You can view pictures using the viewfinder
to avoid wearing down the battery, or when
the picture seen on the LCD screen is poor.
DISPLAY/BATT INFO
Viewfinder
180 degrees
(max.)
2
1
2
90 degrees to the
90 degrees
camcorder
(max.)
Viewfinder lens
adjustment lever
Move it until the
picture is clear.
To turn off the LCD backlight to make
the battery last longer
z Tips
Press and hold DISPLAY/BATT INFO for
• You can adjust the brightness of the viewfinder
backlight by selecting [LCD/VF SET] - [VF
a few seconds until
appears.
This setting is practical when you use your
camcorder in bright conditions or where
you want to save battery power. The
recorded picture will not be affected by the
setting. To turn on the LCD backlight, press
and hold DISPLAY/BATT INFO for a few
The grip belt
Fasten the grip belt and hold your
camcorder correctly.
seconds until
disappears.
b Notes
• Do not press the buttons on the LCD panel
accidentally when you open or adjust the LCD
panel.
z Tips
• If you rotate the LCD panel 180 degrees to the
lens side, you can close the LCD panel with the
LCD screen facing out. This is convenient
during playback operations.
adjust the brightness of the LCD screen.
• Press DISPLAY/BATT INFO to toggle the
screen indicators (such as Battery Info) on or
off.
18
Step 5: Inserting a tape or a “Memory Stick
Duo”
Cassette tape
3
Close the lid.
You can use mini DV
cassettes only
To eject the cassette
Open the lid following the same procedure
as described in step 1 and remove the
cassette.
b Notes
• The recordable time varies depending on [
b Notes
1
Slide and hold the
EJECT lever in the direction of the
arrow and open the lid.
OPEN/
• Do not force the cassette compartment
closed by pressing the portion marked
{DO NOT PUSH} while it is sliding in. It
may cause a malfunction.
OPEN/EJECT lever
“Memory Stick Duo”
You can use “Memory Stick” that have the
–
–
(“Memory Stick Duo”)
(“Memory Stick
PRO Duo”)
Lid
–
(“Memory Stick
The cassette compartment automatically
comes out and opens up.
PRO-HG Duo”)
z Tips
• The number and time of recordable pictures
vary depending on the image quality or the
image size. For details, see page 49.
2
Insert a cassette with its window
facing outwards, then press
.
Push the center of the back
1
2
Open the LCD panel.
of the cassette lightly.
Window
Cassette
Insert the “Memory Stick Duo”
into the Memory Stick Duo slot in
the right direction until it clicks.
compartment
The cassette compartment
automatically slides back in.
Continued ,
19
Step 5: Inserting a tape or a “Memory Stick Duo” (Continued)
Access lamp
To eject a “Memory Stick Duo”
Lightly push the “Memory Stick Duo” in
once.
b Notes
• When the access lamp is lit or flashing, your
camcorder is reading/writing data. Do not shake
or knock your camcorder, turn the power off,
eject the “Memory Stick Duo,” or remove the
battery pack. Otherwise, image data may be
damaged.
• If you force the “Memory Stick Duo” into the
slot in the wrong direction, the “Memory Stick
Duo,” the Memory Stick Duo slot, or image data
may be damaged.
• When inserting or ejecting the “Memory Stick
Duo,” be careful that the “Memory Stick Duo”
does not pop out and drop.
20
RecordinEg/PalasybyackRecording/Playback (Easy Handycam)
With this Easy Handycam operation, most of the camera settings are automatically optimally
adjusted, which frees you from detailed adjustments. The screen font size increases for easy
viewing.
E If the POWER switch is set to
OFF (CHG), slide it while
pressing the green button.
A
D
F
B
C
Movies
Still images
1
Slide the POWER
switch E to turn on
the CAMERA-TAPE
lamp.
1
Slide the POWER
switch E to turn on
the CAMERA-
MEMORY lamp.
2
3
Press EASY C.
2
3
Press EASY C.
appears on the screen
EASY
appears on the screen
EASY
A.
A.
Press START/STOP F or B to
start recording.
Press PHOTO D to record.*
11
60min EASY
101
6.1M
60min
EASY
REC
GUIDE MENU
GUIDE MENU
Flashing t Lit
[STBY] t [REC]
Press and hold lightly
Press fully to record.
to adjust the focus.
To stop recording, press F or B
again.
* Still images are recorded in [FINE] quality on a “Memory Stick Duo.”
Continued ,
21
Easy Recording/Playback (Easy Handycam) (Continued)
Playing back movies/still images
Slide the POWER switch E to turn on the PLAY/EDIT lamp. Touch the buttons
on the touch panel A as follows.
Movies
Still images
Touch
then touch
playback.
to rewind,
to start
Touch
t
/
to select a picture.
A
A
C
GUIDE
C
D
MENU
B
B
A Stop
B Play/Pause toggles
C Rewind/Fast forward
B Tape playback
C Previous/Next
x To cancel Easy Handycam operation
Press EASY C again.
disappears from the screen.
x Adjustable menu settings during Easy Handycam operation
•
is not displayed during Easy Handycam operation.
• Cancel Easy Handycam operation if you want to add any effects or settings to the images.
x Unavailable buttons during Easy Handycam
During Easy Handycam operation, the following buttons/dial are unavailable. [Invalid
during Easy Handycam operation] may appear if operations not available during Easy
Handycam are attempted.
22
Recording
Lens cover
Opens in accordance with the
setting of the POWER switch.
PHOTO
POWER switch
START/STOP B
START/STOP A
Recording movies
Movies are recorded on a tape.
Slide the POWER switch in the direction of the arrow repeatedly
to turn on the CAMERA-TAPE lamp.
If the POWER switch is set to OFF (CHG), slide it
while pressing the green button.
Press START/STOP A (or B).
60min
60min
60min
60min
GUIDE
P-MENU
GUIDE
P-MENU
[REC]
[STBY]
To stop recording, press START/STOP A (or B) again.
z Tips
To record high quality still images during tape recording (Dual Rec)
Continued ,
23
Recording (Continued)
Recording still images
Still images are recorded on the “Memory Stick Duo.”
Slide the POWER switch in the direction of the arrow repeatedly
to turn on the CAMERA-MEMORY lamp.
If the POWER switch is set to OFF (CHG), slide it
while pressing the green button.
Press and hold PHOTO lightly to adjust the focus, then press it
fully to record.
min
min
6.1M
6.1M
Beep
Shutter click
GUIDE
P-MENU
GUIDE
P-MENU
Flashing bLights up
A shutter sound is heard. When
disappears, the image has been recorded.
To check the latest recording on a “Memory Stick Duo”
Touch
. To delete the picture, touch
t [YES].
z Tips
24
Zooming
Recording high quality still
images during tape recording
(Dual Rec)
You can magnify images to 10 times the
original size with the power zoom lever or
the zoom buttons on the LCD panel.
You can record high quality still images on
the “Memory Stick Duo” during tape
recording.
1 Slide the POWER switch to turn on the
CAMERA-TAPE lamp, then press
Power zoom lever
START/STOP to start tape recording.
2 Press PHOTO fully.
For each separate time tape recording, up to
3 still images can be recorded.
Wider range of view:
(Wide angle)
Orange color
boxes indicate
the number of
recorded
images. When
recording is
finished, the
color changes
to orange.
Close view: (Telephoto)
Move the power zoom lever slightly for a
slower zoom. Move it further for a faster
zoom.
3 Press START/STOP to stop tape recording.
Stored still images appear one by one, and
the images are stored onto the “Memory
b Notes
• Be sure to keep your finger on the power zoom
lever. If you move your finger off the power
zoom lever, the operation sound of the power
zoom lever may also be recorded.
• You cannot change the zoom speed with the
zoom buttons on the LCD panel.
• The minimum possible distance between
camcorder and subject while maintaining sharp
focus is about 1 cm (about 13/32 in.) for wide
angle and about 80 cm (about 2 5/8 feet) for
telephoto.
Stick Duo.” When
disappears, the
image has been recorded.
b Notes
• Do not eject the “Memory Stick Duo” before
tape recording is finished and the still images
are stored on the “Memory Stick Duo.”
• You cannot use the flash during Dual Rec.
z Tips
• During the standby mode, still images will be
stored in the same way as when the POWER
switch is set to CAMERA-MEMORY. You can
use the flash.
z Tips
want to zoom to a level greater than 10 ×.
Continued ,
25
Recording (Continued)
• When the POWER switch is set to CAMERA-
TAPE, still images will be recorded at image
size 4.6M in the HDV format, 3.4M (4:3) or
4.6M (16:9) in the DV format.
60min
0:00:00
STBY
DIAL SET
FOCUS
EXPOSURE
SHUTTR SPEED
AE SHIFT
WB SHIFT
RESET
[MANUAL]:EXEC
Controlling the image settings
manually with the CAM CTRL
dial
2 Rotate the CAM CTRL dial and select a
menu item to be assigned.
3 Press the MANUAL button.
It is useful to assign a frequently used menu
item to the CAM CTRL dial.
b Notes
The following is an example of the
procedure when the [FOCUS] setting is
assigned (the default setting).
• The menu item settings done before will be
retained even if you set other menu item settings
after that. If [EXPOSURE] is set after [AE
SHIFT] is set manually, [EXPOSURE] will
override [AE SHIFT].
• If you select [RESET] in step 2, all the settings
set manually return to the default setting.
z Tips
• During playback, you can adjust the volume
using the CAM CTRL dial.
• You can also assign menu items using [DIAL
MANUAL button
CAM CTRL dial
1 Press the MANUAL button to activate the
manual adjustment mode.
The setting mode switches between
automatic and manual every time you press
the MANUAL button.
Using the flash
Flash
2 Rotate the CAM CTRL dial to adjust the
focus manually.
Menu items that can be assigned
– [SHUTTR SPEED] (p. 44)
Flash
button
To assign the menu items to the CAM
CTRL dial
1 Press and hold the MANUAL button for
several seconds.
Press the (flash) button repeatedly to
select an appropriate setting.
No indication (Auto flash): Automatically
flashes when there is insufficient ambient
light.
The [DIAL SET] screen appears.
r
(Forced flash): Always uses the flash
regardless of the surrounding brightness.
26
r
when it is hard to focus automatically.
(No flash): Records without flash.
• Do not use these functions in bright places. This
may cause a malfunction.
b Notes
• Remove the lens hood when you use the flash,
or its shadow will appear in the picture.
z Tips
• To record an image brighter, use Super
more faithful to the original colors, use Color
• The recommended distance to the subject when
using the built-in flash is 0.3 to 2.5 m (1 to 8
feet).
• Remove any dust from the surface of the flash
lamp before using it. Flash effect may be
impaired if heat discoloration or dust obscures
the lamp.
• The /CHG (charge) lamp flickers when
charging the flash, and remains lit when the
flash charge is ready. (In [STBY] of the
CAMERA-TAPE mode, it takes a while to fully
charge the flash.)
Adjusting the exposure for
backlit subjects
• You cannot use the flash during tape recording.
• If you use the flash in bright places such as
when shooting a backlit subject, the flash may
not be effective.
z Tips
To adjust the exposure for backlit subjects,
press . (back light) to display .. To
cancel the backlight function, press .
(back light) again.
• You can change the brightness of the flash by
setting [FLASH LEVEL], or you can prevent
the redeye by setting [REDEYE REDUC], in
Recording in mirror mode
Recording in dark places
(NightShot)
Infrared port
Set the NIGHTSHOT switch to ON (
and [“NIGHTSHOT”] appear).
Open the LCD panel 90 degrees to the
camcorder (1), then rotate it 180 degrees
to the lens side (2).
b Notes
• The NightShot and Super NightShot functions
use infrared light. Therefore, do not cover the
infrared port with your fingers or other objects
and remove the conversion lens (optional) and
the lens hood.
z Tips
• A mirror-image of the subject appears on the
LCD screen, but the picture will be normal
when recorded.
27
Playback
Slide the POWER switch in the direction of the arrow repeatedly to
turn on the PLAY/EDIT lamp.
If the POWER switch is set to OFF (CHG), slide it
while pressing the green button.
Playing movies
Touch
to rewind to the desired scene, then touch
to start
playback.
Toggles Play or Pause as you touch*
60min
60min
GUIDE
P-MENU
Rewind/Fast forward
Stop**
* Playback automatically stops if pause is engaged for more than 3 minutes.
**
is displayed instead of
a tape is not being played.
when a “Memory Stick Duo” with recorded images is inserted and
To adjust the sound volume
z Tips
To search for a scene during playback
Touch and hold
/
during playback (Picture Search), or
/
while fast
forwarding or rewinding the tape (Skip Scan).
z Tips
• You can play back in various modes ([
28
Viewing still images
Touch
.
The most recently recorded image is displayed.
60min
10/10
6.1M
MEMORY PLAY
GUIDE
P-MENU
Switches the
playback media*
Previous/Next
Go to the index screen display
*
is displayed on the tape playback screen.
To display pictures on a “Memory Stick Duo” on the Index screen
Touch
. Touch one of the pictures to back to the single display mode.
B
A
A Previous/Next 6 pictures
B The picture displayed before switching to the index screen
To view pictures in other folders, touch
t
t [PB FOLDER], select a folder with
/
Continued ,
29
Playback (Continued)
Using PB zoom
You can magnify images from about 1.1 to
5 times (from about 1.5 to 5 times in still
images) the original size.
Magnification can be adjusted with the
power zoom lever or the zoom
buttons on the LCD panel.
1 Play back the picture you want to
magnify.
2 Magnify the picture with T (Telephoto).
3 Touch the screen at the point you want
to display in the center of the displayed
frame.
4 Adjust the magnification with W (Wide
angle)/T (Telephoto).
To cancel, touch [END].
30
Using the guide functions (USAGE GUIDE)
You can easily select the desired setting
screens by using the guide functions
(USAGE GUIDE).
Unavailable settings during Easy
Handycam
During Easy Handycam operation, some
60min
STBY
items are unavailable. If an attempted
setting is not available, but still desired,
touch [SET] to display an on-screen
instruction. Follow the instruction to cancel
Easy Handycam operation and then select
the setting.
GUIDE
P-MENU
Your camcorder has 4 guide functions as
shown below.
z Tips
• If [SET] is not displayed in step 3, follow the
instruction on the screen.
SHOOT
GUIDE:
Takes you to the setting
screens related to
recording.
CNNECT
GUIDE:
Recommends the
appropriate connection
method for your device.
USEFUL
GUIDE:
Takes you to the setting
screens related to the
basic operations.
DISP
GUIDE:
Enables you to check the
meaning of each
indicator that appears on
the LCD screen. See
page 110 for details.
1
2
Touch [GUIDE].
Select the desired item.
e.g., to record night views
Touch [SHOOT GUIDE] t [SELECT
SCENE] t
/
to display [To
keep the mood of a night view].
3
Touch [SET].
The desired setting screen appears.
Adjust the settings according to your
purpose.
31
Searching for the starting point
Searching for the last scene of
the most recent recording (END
SEARCH)
Reviewing the most recently
recorded scenes (Rec review)
You can view about 2 seconds of the scene
recorded just before you stopped the tape.
Make sure that the CAMERA-TAPE
lamp lights up (p. 23).
END SEARCH will not work once you
eject the cassette after you have recorded on
the tape.
Make sure that the CAMERA-TAPE
Touch
t
.
60min
STBY
0:00:00
Touch
t
.
60min
END SEARCH
1
0:00:00
EXECUTING
CANCEL
The last 2 seconds (approx.) of the most
recently recorded scene are played back.
Then, your camcorder is set to standby.
Touch here to cancel the operation.
The last scene of the most recent
recording is played back for about 5
seconds, and the camcorder enters the
standby mode at the point where the last
recording has finished.
Searching quickly for a desired
scene (Zero set memory)
Slide the POWER switch repeatedly to
turn on the PLAY/EDIT lamp, then
b Notes
• END SEARCH will not work correctly when
there is a blank section between recorded
sections on the tape.
mREW
z Tips
PLAY
STOP
• You can also select [END SEARCH] from the
menu. When the PLAY/EDIT lamp lights up,
select the [END SEARCH] short-cut in Personal
DISPLAY
ZERO SET
MEMORY
32
• Zero set memory will not function correctly if
there is a blank section between recorded
sections on the tape.
1
During playback, press ZERO
SET MEMORY on the Remote
Commander at a point you want
to locate later on.
Searching for a scene by date of
recording (Date search)
The tape counter is reset to “0:00:00”
and
appears on the screen.
You can locate the point where the
recording date changes.
60min
0:00:00
Slide the POWER switch repeatedly to
GUIDE
P-MENU
SEARCH M.
./>
If the tape counter is not displayed,
press DISPLAY.
STOP
2
3
Press STOP when you want to
stop playback.
Press mREW.
1
2
Press SEARCH M. on the Remote
Commander.
The tape stops automatically when the
tape counter reaches “0:00:00.”
The tape counter returns to the time
code display, and the zero set memory
display disappears.
Press .(Previous)/>(Next) to
select a recording date.
60min
0:00:00:00
60min
DATE -01
SEARCH
GUIDE
4
Press PLAY.
Playback starts from the point
designated “0:00:00” on the tape
counter.
P-MENU
To cancel the operation
Press STOP.
To cancel the operation
Press ZERO SET MEMORY again before
rewinding.
b Notes
• The Date search will not function correctly
when there is a blank section between recorded
sections on the tape.
b Notes
• There may be a discrepancy of several seconds
between the time code and the tape counter.
33
Playing the picture on a TV
Connection methods and image quality
Selecting the appropriate
connection method (CNNECT
GUIDE)
differ depending on what type of TV is
connected and connectors used.
Use the supplied AC Adaptor as the power
source (p. 13).
Your camcorder helps you select the
appropriate connection for your device. The
output setting of your camcorder is then set
automatically.
Refer also to the instruction manuals
supplied with the device to be connected.
b Notes
• Make all menu settings on your camcorder
before connecting. The TV may not recognize
the video signal properly if the [VCR HDV/DV]
or [i.LINK CONV] setting is changed after the
TV and your camcorder were connected with an
i.LINK cable.
• Pictures recorded in the DV format are played
back as SD (standard definition) images
regardless of the connection.
• When recording, set [X.V.COLOR] to [ON] to
Some settings may need to be adjusted on the
TV when playing back.
1
2
3
Touch [GUIDE].
Touch [CNNECT GUIDE].
Connect your camcorder and TV
according to the instructions on
the LCD screen.
Jacks on your camcorder
Open the jack cover in the direction of the
arrow and connect the cable.
An example of connecting to a high
definition TV
1 Touch [TV] t [HD TV].
2 Select the TV input jacks with
, then touch
/
.
3 Check the output setting details, then
touch
.
4 Connect your camcorder and TV,
referring to the picture on the screen.
Touch [HINT] and refer also to the
precautions on connecting.
HDV/DV
COMPONENT OUT A/V OUT
5 Touch
t [END].
4
1
2
z Tips
• To return to the previous question, touch
.
Lift up the bottom of the jack cover, then
rotate in the direction of the arrow.
3
34
Connecting to a high definition TV
HD (high definition) image quality
• An HDV formatted picture is played back as it is
(HD image quality).
• A DV formatted picture is played back as it is (SD image quality).
COMPONENT IN
AUDIO
i.LINK
(for HDV1080i)
HDMI
A
B
C
: Signal flow, ( ): Reference pages
Type Camcorder
Cable
TV
Menu Setting
(STANDARD SET)
[VCR HDV/DV] t
[COMPONENT] t
A
Component video cable
(supplied)
1
(Green) Y
(Blue) PB/CB
(Red) PR/CR
A/V connecting cable
(supplied)
2
(White)
(Red)
(Yellow)
• An A/V connecting cable is also needed to output audio signals. Connect the white and red plugs of the A/
V connecting cable to the audio input jack of your TV.
Continued ,
35
Playing the picture on a TV (Continued)
: Signal flow, ( ): Reference pages
Type Camcorder
Cable
TV
Menu Setting
(STANDARD SET)
[VCR HDV/DV] t
HDMI
IN
B
3
HDMI cable (optional)
• Use an HDMI cable with the HDMI logo (on the front cover).
• Pictures in the DV format are not output from the HDMI OUT jack, if copyright protection signals are
recorded in the pictures.
• Your TVs may not function correctly (e.g., no sound or image). Do not connect the HDMI OUT jack of
your camcorder and HDMI OUT jack of an external device with the HDMI cable. This may cause a
malfunction.
(STANDARD SET)
[VCR HDV/DV] t
[i.LINK CONV] t
C
i.LINK cable (supplied)
4
• Your TV needs to have an i.LINK jack compatible with HDV1080i specification. For details,
confirm the specifications of your TV.
• If your TV is not compatible with HDV1080i specification, connect your camcorder and TV with the
supplied component video cable and A/V connecting cable as illustrated in
.
• The TV needs to be set so that it recognizes that the camcorder is connected. See the instruction manuals
supplied with your TV.
Connecting to a 16:9 (wide) or 4:3 TV
SD (standard definition) image quality
• An HDV formatted picture is down converted to DV format
(SD image quality) and played back.
• A DV formatted picture is played back as it is (SD image quality).
COMPONENT IN
AUDIO
VIDEO/AUDIO
S VIDEO
i.LINK
VIDEO/AUDIO
D
E
F
G
36
To set the aspect ratio according to the connected TV (16:9/4:3)
b Notes
• When you play back a tape recorded in the DV format on a 4:3 TV not compatible with the 16:9 signal, set
[
: Signal flow, ( ): Reference pages
Type Camcorder
Cable
TV
Menu Setting
(STANDARD SET)
[VCR HDV/DV] t
[COMPONENT] t
[480i] (59)
[TV TYPE] t
[16:9]/[4:3] (59)
D
Component video cable
(supplied)
1
(Green) Y
(Blue) PB/CB
(Red) PR/CR
A/V connecting cable
(supplied)
2
(White)
(Red)
(Yellow)
• A/V connecting cable is also needed to output audio signals. Connect the white and red plugs of the A/V
connecting cable to the audio input jack of your TV.
(STANDARD SET)
[VCR HDV/DV] t
E
[i.LINK CONV] t
i.LINK cable (supplied)
4
• The TV needs to be set so that it recognizes that the camcorder is connected. See the instruction manuals
supplied with your TV.
Continued ,
37
Playing the picture on a TV (Continued)
: Signal flow, ( ): Reference pages
Type Camcorder
Cable
TV
Menu Setting
(STANDARD SET)
[VCR HDV/DV] t
A/V connecting cable with
S VIDEO (optional)
[TV TYPE] t
[16:9]/[4:3] (59)
2
(White)
(Red)
(Yellow)
• When connecting only an S VIDEO plug (S VIDEO channel), audio signals are not output. To output
audio signals, connect the white and red plugs of the A/V connecting cable with an S VIDEO cable to the
audio input jack of your TV.
• This connection produces higher resolution pictures compared with the A/V connecting cable (Type
).
A/V connecting cable
(supplied)
(STANDARD SET)
[VCR HDV/DV] t
[TV TYPE] t
[16:9]/[4:3] (59)
2
(Yellow)
(White)
(Red)
connecting Sony’s PhotoTV HD-
compatible devices using an HDMI cable*
or component video cable**, a whole new
world of photos can be enjoyed in
breathtaking full HD quality.
When connecting to your TV via a VCR
Select one of the connecting methods on
page 64, according to the input jack of the
VCR. Connect your camcorder to the LINE
IN input on the VCR using the A/V
connecting cable. Set the input selector on
the VCR to LINE (VIDEO 1, VIDEO 2,
etc.).
*
The TV will automatically switch to the
appropriate mode when displaying photos.
** Setup of the TV will be necessary.
Please refer to the instruction manual of
your PhotoTV HD-compatible TV for
details.
When your TV is monaural (When your
TV has only one audio input jack)
Connect the yellow plug of the A/V
connecting cable to the video input jack and
connect the white (left channel) or the red
(right channel) plug to the audio input jack
of your TV or VCR.
z Tips
• The HDMI (High Definition Multimedia
Interface) is an interface to send both video/
audio signals. Connecting HDMI OUT jack and
external device with a cable supplies high
quality images and digital audio.
• If you connect your camcorder to your TV using
more than one type of cable to output images
from a jack other than the i.LINK jack, the order
of priority of the output signals is as follows:
HDMI t component video t S VIDEO t
audio/video.
On“PhotoTV HD”
This camcorder is compatible with the
“PhotoTV HD” standard. “PhotoTV HD”
allows for highly-detailed, photo-like
depiction of subtle textures and colors. By
38
Using the Menu
Using the menu items
1
2
Slide the POWER switch in the direction of the arrow
repeatedly to turn on the respective lamp.
CAMERA-TAPE lamp:
settings on a tape
settings on a “Memory Stick
CAMERA-MEMORY lamp:
Duo”
PLAY/EDIT lamp: settings for viewing/editing
Touch the LCD screen to select the menu item.
Unavailable items will be grayed out.
x To use the short-cuts of
Personal Menu
On Personal Menu, short-cuts for
frequently used menu items are added.
x To use menu items
You can customize menu items that are
not added to Personal Menu.
1 Touch
t [MENU].
2 Select the desired menu.
z Tips
Touch
touch
/
to select the item, then
• You can customize Personal Menu as you
(The process in step 3 is
the same as that in step 2).
3 Select the desired item.
4 Customize the item.
1 Touch
.
60min
STBY
0:00:00
After finishing the settings, touch
DISP
GUIDE
MENU
t
screen.
(close) to hide the menu
SCENE
SELECT
SMOOTH
SLWREC
1/3
If you decide not to change the setting,
TELE
MACRO
FADER
touch
to return to the previous
screen.
2 Touch the desired item.
If the desired item is not displayed on
x To use menu items during Easy
Handycam operation
the screen, touch
is displayed.
/
until the item
is not displayed during Easy
Handycam operation. Touch [MENU]
to display the menu index screen.
3 Select the desired setting, then touch
.
39
Available menu items (z) vary depending on which lamp is lit.
During Easy Handycam operation, the setting is set automatically
as shown in the following list.
Menu items
Position of lamp:
TAPE
MEMORY PLAY/EDIT Easy Handycam
SCENE SELECT
SPOT MTR·FCS
SPOT METER
EXPOSURE
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
AUTO
–
–
AUTO
AUTO
–
WHITE BAL.
SHARPNESS
SHUTTR SPEED
AUTOSLW SHTR
AE SHIFT
AUTO
ON
z
z
z
z
z
z
z
z
–
OFF
–
CAMERA COLOR
WB SHIFT
OFF
AUTO
AUTO
OFF
OFF
*1/OFF
OFF
ON
SPOT FOCUS
FOCUS
TELE MACRO
PEAKING
FLASH SET
SUPER NS
NS LIGHT
z
z
z
z
z
–
COLOR SLOW S
ZEBRA
OFF
OFF
OFF
z*2
HISTOGRAM
SELF-TIMER
DIGITAL ZOOM
STEADYSHOT
CONV.LENS
OFF
ON
–*1
z
z
z
–
DIAL SET
–
–*1
X.V.COLOR
STILL SET
–
–
–
–
–
–
–
z
–
z
z
z
z
z
z
z
FINE/z*1
ALL ERASE
z
FORMAT
z
z
z
z
–
–
–*1
–
–*1
–*1
FILE NO.
NEW FOLDER
REC FOLDER
PB FOLDER
FADER
z
–
–
z
–
–
OFF
OFF
–
INT.REC-STL
–
SLIDE SHOW
–
z
z
z
D.EFFECT
z
z
–
OFF
OFF
PICT.EFFECT
–
40
Position of lamp:
TAPE
z
MEMORY PLAY/EDIT Easy Handycam
SMTH SLW REC
PictBridge PRINT
USB SELECT
–
–
–
–
–
z
z
–
–
–
–
–
–
DEMO MODE
z
ON
VAR.SPD PB
–
–
–
–
–
z
z
z
–
–
–
REC CTRL
END SEARCH
z
VCR HDV/DV
–
–
–
z
AUTO
z*1
REC FORMAT
z
–
SP*1/16:9 WIDE*1/
DV SET
z
–
z
*1/
–*1
VOLUME
z
z
z
z
z*1*3
MIC LEVEL
–
–
AUTO
– /NORMAL/ – /
NORMAL
LCD/VF SET
z
z
z
COMPONENT
i.LINK CONV
TV TYPE
z
z
z
z
z
z
z
z
–
z
–
z
z
z
z
z
–
1080i/480i*1
OFF*1
16:9*1
z
z
–
DISP GUIDE
STATUS CHECK
GUIDEFRAME
CENTER MARKR
COLOR BAR
DATA CODE
REMAINING
REMOTE CTRL
REC LAMP
z
–
z
z
–
OFF
OFF
OFF
z
–
–
–
z
z
z
–
z
z
z
z
z
z
z
–
–
AUTO
ON
z
z
z
z
z
z
–
ON
z*1
BEEP
z
z
z
z
z
–
DISP OUTPUT
MENU ROTATE
A.SHUT OFF
CALIBRATION
QUICK REC
LCD PANEL
–
5min
–
z
–
OFF
CLOCK SET
z
z
z
z
z
z
z
z
z
z*1
–*1
–*1
WORLD TIME
LANGUAGE
*1 The setting value before entering Easy Handycam operation will be retained.
*2 Cannot be operated in the CAMERA-TAPE mode.
*3 Available only when the POWER switch is set to PLAY/EDIT.
41
CAMERA SET menu
Settings to adjust your camcorder to the
recording conditions
FIREWORKS* (
)
Select to record all the splendor of
fireworks.
The default settings are marked with B.
The indicators in parentheses appear when
the items are selected.
menu items.
LANDSCAPE* (
)
SCENE SELECT
Select to shoot distant subjects clearly.
This setting also prevents your camcorder
from focusing on glass or metal mesh in
windows between the camcorder and the
subject.
You can record pictures effectively in
various situations with the [SCENE
SELECT] function.
BAUTO
Select to automatically record pictures
effectively without the [SCENE SELECT]
function.
PORTRAIT (Soft portrait) (
)
TWILIGHT* (
)
Select to bring out the subject such as
people or flowers while creating a soft
background.
Select to maintain the darkening
atmosphere of the distant surroundings in
twilight scenes.
SPOTLIGHT** (
)
TWILIT PORTRT (Twilight portrait) (
Select to photograph people and
background using the flash when recording
still images.
)
Select to prevent people’s faces from
appearing excessively white when subjects
are lit by strong light.
BEACH** (
)
CANDLE (
)
Select to prevent people’s faces from
appearing dark in strong light or reflected
light, such as at a beach in midsummer.
Select to maintain the dim atmosphere of a
candlelit scene.
SUNRSE SUNSET (Sunrise and sunset)*
SNOW** (
)
(
)
Select this when shooting in very bright,
white conditions, such as on a ski slope;
otherwise picture may appear too dark.
Select to maintain the atmosphere of
situations such as sunsets and sunrises.
42
* Adjusted to focus on subjects farther away
only.
1
**Adjusted not to focus on subjects a short
distance away.
2
b Notes
• If you set [SCENE SELECT], the settings of
[SHUTTR SPEED] and [WHITE BAL.] are
canceled.
1 Touch the point where you want to fix and
adjust the exposure on the screen.
appears.
2 Touch [END].
SPOT MTR·FCS (Spot Meter &
Spot Focus)
To return the setting to automatic exposure,
touch [AUTO] t [END].
You can adjust the brightness and the focus
of a picture at the same time.
You can use the functions [SPOT METER]
same time.
b Notes
• If you set [SPOT METER], [EXPOSURE] is
automatically set to [MANUAL].
EXPOSURE
1 Touch the point on the screen where you
want to adjust and fix the exposure and the
focus.
You can fix the brightness of a picture
manually. Adjust the brightness when the
subject is much brighter or darker than the
background.
and 9 appear.
1
2
2
2 Touch [END].
3
1
1 Touch [MANUAL].
To return the setting to automatic exposure
and focus, touch [AUTO]t[END].
appears.
2 Adjust the exposure by touching
/
b Notes
.
• If you set [SPOT MTR·FCS] , [EXPOSURE]
and [FOCUS] are automatically set to
[MANUAL].
3 Touch
.
To return the setting to automatic exposure,
touch [AUTO] t
.
SPOT METER (Flexible spot
meter)
z Tips
• You can also adjust the setting manually using
You can adjust and fix the exposure to the
subject, so that it is recorded in suitable
brightness even when there is strong
contrast between the subject and the
background, such as subjects in the
spotlight on stage.
WHITE BAL. (White balance)
You can adjust the color balance to the
brightness of the recording environment.
Continued ,
43
CAMERA SET menu (Continued)
z Tips
BAUTO
The white balance is adjusted
automatically.
• If you have changed the battery pack while
[AUTO] was selected, or taken your camcorder
outdoors after inside use (or vice versa), select
[AUTO] and aim your camcorder at a nearby
white object for about 10 seconds for better
color balance adjustment.
• When the white balance has been set with [ONE
PUSH], if you change the [SCENE SELECT]
settings, or bring your camcorder outdoors from
inside the house, or vice versa, you need to redo
the [ONE PUSH] procedure to readjust the
white balance.
OUTDOOR (
)
The white balance is appropriately
adjusted for the following recording
conditions:
– Outdoors
– Night views, neon signs and fireworks
– Sunrise or sunset
– Under daylight fluorescent lamps
INDOOR (n)
The white balance is appropriately
adjusted for the following recording
conditions:
SHARPNESS
You can adjust the sharpness of the image
outline with
the sharpness is anything other than the
default setting.
/
.
appears when
– Indoors
– At party scenes or studios where the lighting
conditions change quickly
– Under video lamps in a studio, or under
sodium lamps or incandescent-like color
lamps
Soften
Sharpen
ONE PUSH (
The white balance will be adjusted
according to the ambient light.
)
SHUTTR SPEED
You can manually adjust and fix the shutter
speed for your convenience. Depending on
the shutter speed, you can make the subject
look still, or emphasize movement of the
subject.
1 Touch [ONE PUSH].
2 Frame a white object such as a piece of
paper, to fill the screen under the same
lighting conditions as you will shoot
the subject.
BAUTO
Select to adjust the shutter speed
automatically.
3 Touch [
].
flashes quickly. When the white
balance has been adjusted and stored in
the memory, the indicator stops
flashing.
MANUAL(
)
Adjust the shutter speed using
.
/
b Notes
You can select a shutter speed between 1/4
and 1/10000 second when the POWER
switch is set to CAMERA-TAPE, and
between 1/4 and 1/500 second when the
POWER switch is set to CAMERA-
MEMORY.
• Set [WHITE BAL.] to [AUTO] or adjust the
color in [ONE PUSH] under white or cool white
fluorescent lamps.
• When you select [ONE PUSH], keep framing
white objects while
flashes slowly if [ONE PUSH] could not
be set.
• When [ONE PUSH] was selected, if
is flashing quickly.
•
125, 180, 250
Slower
Faster
keeps
flashing after touching
BAL.] to [AUTO].
, set [WHITE
• If you set [WHITE BAL.], [SCENE SELECT]
returns to [AUTO].
44
b Notes
• When the shutter speed is set between 1/725 to
1/10000 second, still images cannot be recorded.
• For example, if you select 1/100 second, [100]
appears on the screen.
Decreases color
intensity
Increases color
intensity
• At a slow shutter speed, automatic focus may be
lost. Adjust the focus manually, using a tripod,
etc.
WB SHIFT (White Balance Shift)
You can adjust the white balance to the
desired setting using
/
.
• When recording under a discharge tube such as
a fluorescent lamp, sodium lamp or mercury
lamp, horizontal bands may appear in the screen
depending on the shutter speed.
and the setting value appear when [WB
SHIFT] is anything other than the default
setting.
z Tips
z Tips
• You can also adjust the setting manually using
• When the white balance is set to a lower value,
pictures appear bluish, and when set to a higher
value, pictures appear reddish.
• You can also adjust the setting manually using
AUTOSLW SHTR (Auto slow
shutter)
When you set [AUTOSLW SHTR] to
[ON], the shutter speed is slowed down
automatically to 1/30 second in dark places.
SPOT FOCUS
You can select and adjust the focal point to
a subject not located in the center of the
screen.
AE SHIFT
You can adjust the exposure using
1
(dark)/
(bright).
and the setting
value appear when [AE SHIFT] is anything
other than the default setting.
2
z Tips
• Touch
backlight is bright, or touch
is black or the light is dim.
1 Touch the subject on the screen.
9 appears.
2 Touch [END].
if the subject is white or the
if the subject
To adjust the focus automatically, touch
[AUTO] t [END].
• You can adjust the automatic exposure level to
brighter or darker when [EXPOSURE] is set to
[AUTO].
b Notes
• If you set [SPOT FOCUS], [FOCUS] is
automatically set to [MANUAL].
• You can also adjust the setting manually using
CAMERA COLOR
FOCUS
You can adjust the color intensity with
/
.
appears when [CAMERA
You can adjust the focus manually. You can
select this function also when you want to
focus on a certain subject intentionally.
COLOR] is anything other than the default
setting.
Continued ,
45
CAMERA SET menu (Continued)
1 Touch [MANUAL].
9 appears.
2 Touch
To cancel, touch [OFF], or zoom to wide-
angle (W side).
(focusing on close subjects)/
(focusing on distant subjects) to
b Notes
sharpen the focus.
appears when the
focus cannot be adjusted any closer, and
appears when the focus cannot be adjusted
farther away.
• When recording a distant subject, focusing may
be difficult and can take some time.
when it is hard to focus automatically.
If you touch
,
appears, and you
can adjust the focus to infinity.
3 Touch
.
PEAKING
The outline of the subject on the screen is
enhanced for easier focusing. You can set
the outline color displayed on the screen
during peaking. If you change the default
To adjust the focus automatically, touch
[AUTO] t
.
b Notes
• The minimum possible distance between
camcorder and subject while maintaining sharp
focus is about 1 cm (about 13/32 in.) for wide
angle and about 80 cm (about 2 5/8 feet) for
telephoto.
setting,
is displayed on the screen.
BOFF
Do not set this function.
WHITE
z Tips
Makes the outline color white.
• It is easier to focus on the subject by moving the
power zoom lever towards T (telephoto) to
adjust the focus, then towards W (wide angle) to
adjust the zoom for recording. When you want
to record a subject at close range, move the
power zoom lever to W (wide angle), then
adjust the focus.
RED
Makes the outline color red.
YELLOW
Makes the outline color yellow.
z Tips
• You can also adjust the focus manually using
• The peaking is not recorded on the tape.
FLASH SET
TELE MACRO
You can set this function when you use the
built-in flash or an external flash (optional)
that is compatible with your camcorder.
This is useful to shoot small subjects, such
as flowers or insects. You can blur out
backgrounds and the subject stands out
clearer.
x FLASH LEVEL
When you set [TELE MACRO] to [ON]
(
HIGH(
)
the T (Telephoto) side automatically and
allows for recording subjects at a close
distance down to about 45 cm (17 3/4 in.).
Makes the flash level higher.
BNORMAL(
LOW(
Makes the flash level lower.
)
)
46
x REDEYE REDUC
You can prevent redeye by activating the
flash before recording.
Set [REDEYE REDUC] to [ON], then press
select a setting.
NS LIGHT (NightShot Light)
When using either the NightShot (p. 27) or
can record clearer pictures by setting [NS
LIGHT], which emits infrared light
(invisible), to [ON] (the default setting).
(Auto redeye reduction): Pre-flashes to
reduce redeye before the flash automatically
flashes when there is insufficient ambient
light.
b Notes
• Do not cover the infrared port with your fingers
• Remove the conversion lens (optional) and the
lens hood.
• The maximum shooting distance using [NS
LIGHT] is about 3 m (10 feet).
r
(Forced redeye reduction): Always uses
the flash and the redeye reducing pre-flash.
r
(No flash): Records without flash.
COLOR SLOW S (Color Slow
Shutter)
b Notes
• The redeye reduction may not produce the
desired effect due to individual differences and
other conditions.
When you set [COLOR SLOW S] to [ON],
you can record an image brighter in color
even in dark places.
and [COLOR SLOW SHUTTER]
appear on the screen.
SUPER NS (Super NightShot)
The picture will be recorded at a maximum
of 16 times the sensitivity of NightShot
recording if you set [SUPER NS] to [ON]
also set to ON.
To cancel [COLOR SLOW S], touch
[OFF].
b Notes
• Adjust the focus manually ([FOCUS], p. 45)
when it is hard to focus automatically.
• The shutter speed of your camcorder changes
depending on the brightness. The motion of the
picture may slow down at this time.
and [“SUPER NIGHTSHOT”] appear
on the screen.
To return to the normal setting, set [SUPER
NS] to [OFF], or set the NIGHTSHOT
switch to OFF.
ZEBRA
b Notes
• Do not use NightShot/[SUPER NS] in bright
places. This may cause a malfunction.
• Do not cover the infrared port with your fingers
• Remove the conversion lens (optional) and the
lens hood.
when it is hard to focus automatically.
Diagonal stripes appear in portions of the
screen where brightness is at a preset level.
This is useful as a guide when adjusting the
brightness. When you change the default
setting,
is displayed. The zebra pattern
is not recorded.
BOFF
• The shutter speed of your camcorder changes
depending on the brightness. The motion of the
picture may slow down in this case.
The zebra pattern is not displayed.
70
The zebra pattern appears at a screen
brightness level of about 70 IRE.
Continued ,
47
CAMERA SET menu (Continued)
z Tips
100
The zebra pattern appears at a screen
brightness level of about 100 IRE or
higher.
• You can also operate by pressing PHOTO on
DIGITAL ZOOM
b Notes
• Portions of the screen where brightness is about
100 IRE or higher may appear overexposed.
You can select the maximum zoom level in
case you want to zoom to a level greater
than 10 × (the default setting) while
recording on a tape. Note that the image
quality decreases when you are using the
digital zoom.
z Tips
• IRE represents the screen brightness.
HISTOGRAM
When you set [HISTOGRAM] to [ON], the
[HISTOGRAM] (a graph to display a
distribution of tones in your picture)
window appears on the screen.
This item is useful when you adjust
exposure. You can adjust the [EXPOSURE]
or [AE SHIFT] checking the
The right side of the bar shows the digital
zooming factor. The zooming zone
appears when you select the zooming
level.
[HISTOGRAM] window. The
[HISTOGRAM] will not be recorded on a
tape or “Memory Stick Duo.”
BOFF
Up to 10 × zoom is performed optically.
20 ×
Up to 10 × zoom is performed optically,
and after that, up to 20 × zoom is
performed digitally.
Darker
Brightness
Brighter
STEADYSHOT
You can compensate for camera shake (The
default setting is [ON]). Set
[STEADYSHOT] to [OFF] ( ) when
using a tripod (optional), then the image
becomes natural.
z Tips
• The left area on the graph shows the darker
areas of the picture while the right area shows
the brighter areas.
SELF-TIMER
A still image is recorded after about 10
seconds.
Press PHOTO when [SELF-TIMER] is set
to [ON] and
appears.
To cancel the count down, touch [RESET].
To cancel the self-timer, select [OFF].
48
MEMORY SET menu
Settings for the “Memory Stick Duo”
The default settings are marked with B.
The indicators in parentheses appear when
the items are selected.
See page 39 for details on selecting
menu items.
CONV.LENS
When using an optional conversion lens,
use this function to record using the
optimum compensation for camera shake
for each lens.
STILL SET
BOFF
Select this when the conversion lens
(optional) is not used.
x
QUALITY
BFINE (
)
WIDE CONV. (
Select this to use the wide conversion lens
(optional).
)
Records still images at the fine image
quality level.
STANDARD (
Records still images at the standard image
quality level.
)
TELE CONV. (
Select this to use the tele conversion lens
(optional).
)
b Notes
DIAL SET
• Image quality is automatically fixed to [FINE]
during Easy Handycam operation.
You can select a menu item to assign to the
x
IMAGE SIZE
B6.1M (
Records still images clearly.
)
6.1M
X.V.COLOR
When recording, set to [ON] to capture
wider range of colors.
Various colors such as the brilliant color of
flowers and turquoise blue of the sea can be
more faithfully reproduced.
4.6M (
)
4.6M
Records still images clearly in the 16:9
(wide) ratio.
3.1M (
)
3.1M
Allows you to record more still images in
relatively clear quality.
b Notes
• Set [X.V.COLOR] to [ON] only when the
recorded content will be played back on an
x.v.Color-compliant TV.
• If the movie recorded with this function [ON] is
played back on a non-x.v.Color-compliant TV,
the color may not be reproduced correctly.
VGA (0.3M) (
Allows for the maximum number of
images to be recorded.
)
b Notes
• [ IMAGE SIZE] can be set only when the
POWER switch is set to CAMERA-MEMORY.
• [X.V.COLOR] cannot be set to [ON] when:
– Recording in DV format
– A movie is being recorded.
Continued ,
49
MEMORY SET menu (Continued)
Capacity of the “Memory Stick Duo”
and the number of recordable pictures
* [
IMAGE SIZE] is fixed to [
4.6M] in
HDV or DV format (16:9) and [3.4M] in DV
format (4:3).
When the POWER switch is set to CAMERA-
MEMORY
When the POWER switch is set to PLAY/
EDIT*
6.1M
4.6M
3.1M
VGA
2848 × 2848 × 2048 × 640 ×
1.2M
1440 ×
810
VGA
640 ×
480
0.2M
640 ×
360
2136
1602
1536
480
6.1M
4.6M
3.1M
128MB
256MB
512MB
1GB
41
98
55
130
80
185
780
1970
1.2M
128MB
256MB
512MB
1GB
205
490
780
1970
980
1970
75
175
95
235
140
335
1400
3550
370
890
1400
3550
1750
3550
150
365
205
485
295
690
2900
7300
770
1800
2900
7300
3650
7300
315
740
420
950
610
6000
1400 14500
1550
3750
6000
14500
7500
14500
2GB
630
1500
850
2000
1200
2850
12000
30000
2GB
3150
7500
12000
30000
15000
30000
4GB
1250
2950
1650
3950
2400
5600
23500
59500
4GB
6300
14500
23500
59500
29500
59500
8GB
2500
6000
3350
4900 48000
8000 11000 115000
8GB
12500
48000
60000
30000 115000 115000
When the POWER switch is set to CAMERA-
TAPE*
* [
IMAGE SIZE] is fixed to [
1.2M] in
HDV format, [
0.2M] in DV format (16:9)
and [VGA (0.3M)] in DV format (4:3).
4.6M
3.4M
2848 × 1602 2136 × 1602
b Notes
4.6M
3.4M
• All numbers measured at the following settings:
Top: [FINE] is selected for image quality.
Bottom: [STANDARD] is selected for image
quality.
• When using a “Memory Stick Duo” made by
Sony Corporation. The number of pictures you
can record varies depending on the recording
environment and the recording media.
• The unique pixel array of Sony’s ClearVid
CMOS sensor and image processing system
(new Enhanced Imaging Processor) allows for
still image resolution equivalent to the sizes
described.
128MB
256MB
512MB
1GB
55
130
74
170
95
235
130
305
205
485
275
630
420
950
560
1300
2GB
850
2000
1100
2600
4GB
1650
3950
2250
5200
8GB
3350
8000
4500
10000
50
ALL ERASE
FILE NO.
Deletes all the pictures without image
protection on a “Memory Stick Duo” or in
the selected folder.
BSERIES
Assigns file numbers in sequence even if
the “Memory Stick Duo” is replaced with
another one. The file number is reset when
a new folder is created or the recording
folder is replaced with another.
1 Select [ALL FILES] or [CURRNT
FOLDER].
[ALL FILES]: Deletes all the images on
the “Memory Stick Duo.”
RESET
Resets the file number to 0001 each time
the “Memory Stick Duo” is changed.
[CURRNT FOLDER]: Deletes all the
images in the selected folder.
2 Touch [YES] twice t
.
NEW FOLDER
b Notes
You can create a new folder (102MSDCF
to 999MSDCF) on a “Memory Stick Duo.”
When 9,999 images are stored in the current
folder, a new folder is automatically created
for storing subsequent images.
• The folder will not be deleted even when you
delete all the pictures in the folder.
• Do not do any of the following while [
Erasing all data…] is displayed:
– Operate the POWER switch/operation
buttons.
– Eject the “Memory Stick Duo.”
Touch [YES] t
.
b Notes
FORMAT
• You cannot delete the created folders using your
camcorder. You will have to format the
using your computer.
• The number of recordable pictures on a
“Memory Stick Duo” may decrease as the
number of folders increases.
The “Memory Stick Duo” has been
formatted at the factory, and does not
require formatting at purchase.
To execute formatting, touch [YES] twice
t
.
Formatting is completed, and all the images
will be deleted.
REC FOLDER (Recording folder)
Select the folder to be used for recording
b Notes
• Do not do any of the following while [
Formatting…] is displayed:
with
/
, then touch
.
b Notes
– Operate the POWER switch/operation
buttons.
• As the default setting, pictures are saved in the
101MSDCF folder.
– Eject the “Memory Stick Duo.”
• Once you record a picture in a folder, the same
folder will be set as the default folder for
playback.
• Formatting erases everything on the “Memory
Stick Duo” including protected image data and
newly created folders.
PB FOLDER (Playback folder)
Select the playback folder with
then touch
/
,
.
51
PICT.APPLI. menu
Special effects on pictures or additional
functions on recording/playback
INT.REC-STL (Interval photo
recording)
The default settings are marked with B.
The indicators in parentheses appear when
the items are selected.
menu items.
You can record still images on the
“Memory Stick Duo” at a selected interval.
This function is useful to observe the
movement of clouds or the changes in
daylight, etc.
FADER
You can record a transition with the
following effects adding to the interval
between scenes.
[a]: Recording
[b]: Interval
1 Select the desired effect in [STBY] (to
fading in) or [REC] (to fading out) mode,
1 Touch
or 10 minutes) t
t
t a desired interval time (1, 5
t [ON] t
then touch
.
2 Press START/STOP.
The fader indicator stops flashing and
disappears when the fade is complete.
.
2 Press PHOTO fully.
stops flashing and the interval still
image recording starts.
To cancel before starting the operation,
touch [OFF] in step 1.
Once you press START/STOP, the setting
is canceled.
To cancel [INT.REC-STL], select [OFF].
SLIDE SHOW
STBY
REC
Plays back in sequence the images stored
on a “Memory Stick Duo,” or in a folder
(slide show).
Fading out
Fading in
WHITE FADER
1 Touch
2 Select [ALL FILES ( )] or [CURRNT
FOLDER ( )], then touch
If you select [CURRNT FOLDER ( )],
all the images in the current playback
played back in sequence.
t [PB FOLDER].
.
BLACK FADER
MOSAIC FADER
3 Touch [REPEAT].
4 Select [ON] or [OFF], then
To repeat the slide show, select [ON]
).
To execute the slide show only once, select
[OFF].
.
(
MONOTONE
When fading in, the picture gradually
changes from black and white to color.
When fading out, it gradually changes from
color to black and white.
5 Touch [END] t [START].
To cancel [SLIDE SHOW], touch [END].
To pause, touch [PAUSE].
52
z Tips
• You can select the first picture for the slide
show with
[START].
/
before touching
FLASH (flash motion)
Records/plays back a movie with a serial-
still-image effect (strobe effect).
D.EFFECT (Digital effect)
You can add digital effects to recording/
playback.
TRAIL
When recording/playback, trailing after
images are left in the picture.
1 Touch the desired effect.
2 Adjust the effect with
OLD MOVIE
Adds an old movie effect with a sepia hue
to pictures.
/
, then
touch
.
Effect
Items to adjust
b Notes
CINEMA
EFECT*
No adjustment necessary
• You cannot change to another digital effect
while recording pictures on a tape with
[CINEMA EFECT] selected.
STILL
The degree of
• Effects added to the playback pictures are not
output via the HDV/DV Interface (i.LINK).
Only the original pictures can be output.
• While using [D.EFFECT], you cannot use the
review button for still images on the “Memory
transparency of the still
image you want to
superimpose under a
movie
FLASH
TRAIL
The interval of frame-by-
frame recording/playback
Stick Duo”
.
• If you set [CINEMA EFECT], [SPOT METER]
and [EXPOSURE] return to [AUTO].
• You cannot add special effects to pictures from
devices connected to your camcorder.
The fade time of the
incidental image
OLD
No adjustment necessary
MOVIE*
z Tips
• You can save pictures edited using special
record them on VCR or DVD/HDD recorders
* Available during tape recording only.
3 Touch
.
appears.
To cancel [D.EFFECT], touch [OFF].
BOFF
Does not use [D.EFFECT] setting.
CINEMA EFECT (Cinematic effect)
You can add a cinematic atmosphere to
pictures by adjusting the image quality.
STILL
Records/plays back a movie while
superimposing it on a still image
memorized by touching [STILL].
Continued ,
53
PICT.APPLI. menu (Continued)
z Tips
PICT.EFFECT (Picture effect)
• You can save pictures edited using special
record them on VCR or DVD/HDD recorders
You can add special effects to a picture
during recording or playback.
appears.
BOFF
Does not use [PICT.EFFECT] setting.
SMTH SLW REC (Smooth slow
recording)
SKINTONE*
Makes skin texture look more smoother
and more appealing.
Fast moving subjects and actions, which
cannot be captured under general shooting
conditions, can be shot in smooth moving
slow-motion for about 3 seconds.
NEG.ART
This is useful to shoot fast actions such as a
golf or tennis swing.
The color and brightness are reversed.
Press START/STOP on the [SMTH SLW
REC] screen.
SEPIA
Pictures appear in sepia.
A 3 second-movie (approx.) is recorded as a
12 second slow-motion movie.
[Recording···] disappears, when recording
is finished.
B&W (Black and white)
Pictures appear in black and white.
SOLARIZE
Touch
to set the following.
– [TIMING]
Select the recording start point from the time
START/STOP is pressed (The default setting is
[3sec AFTER]).
Pictures appear as an illustration with
strong contrast.
PASTEL*
[3sec AFTER]
Pictures appear as a pale pastel drawing.
MOSAIC*
[3sec BEFORE]
– [RECORD SOUND]
If you set to [ON] (
Pictures appear mosaic-patterned.
), you can record
additional dialog, etc. to the slow-motion movie
(The default setting is [OFF]).
Sounds are recorded while [Recording···] is
displayed.
* Available during tape recording only.
b Notes
• Effects added to the playback pictures are not
output via the HDV/DV Interface (i.LINK).
Only the original pictures can be output.
• You cannot add special effects to pictures from
devices connected to your camcorder.
b Notes
• Sounds cannot be recorded while shooting a 3
second-movie (approx.).
54
EDIT/PLAY menu
Settings for editing or playing back in
various modes
• The image quality of [SMTH SLW REC] is
somewhat less than normal recording.
See page 39 for details on selecting
menu items.
To cancel [SMTH SLW REC], select
[END].
VAR.SPD PB
(Various speed playback)
PictBridge PRINT
You can play back in various modes while
viewing movies.
USB SELECT
1 Touch the following buttons during
You can connect the camcorder to a
personal computer with a USB cable and
import pictures to the computer. You can
also connect the camcorder to a PictBridge
compatible printer using this function.
Refer to “First Step Guide” on the supplied
CD-ROM for details.
playback.
To
Touch
change the
playback
direction*
(frame)
play back
slowly**
To reverse direction:
B
Memory Stick
(frame) t
Select this to view pictures on a “Memory
Stick Duo” on the computer or to import
them to the computer.
play back frame
by frame
(frame) during
playback pause.
To reverse direction:
(frame) during
PictBridge PRINT
Select this when you connect the
camcorder to a PictBridge compatible
frame playback.
* Horizontal lines may appear at the top,
bottom, or in the center of the screen. This
is not a malfunction.
DEMO MODE
**Pictures output from the HDV/DV
Interface (i.LINK) cannot be played back
smoothly in slow mode.
The default setting is [ON], allowing you to
view the demonstration about 10 minutes
after you have removed both a cassette and
a “Memory Stick Duo” from your
camcorder, and slide the POWER switch to
turn on the CAMERA-TAPE lamp.
2 Touch
To return to the normal playback mode,
touch (Play/Pause) twice (once from
t
.
frame playback).
z Tips
• The demonstration will be suspended in
situations such as those described below.
– When you touch the screen during the
demonstration (The demonstration starts
again after about 10 minutes).
b Notes
• You will not hear the recorded sound. You may
see mosaic-like images of the previously played
picture.
• Pictures in the HDV format are not output from
the HDV/DV Interface (i.LINK) when they
are paused or played back in any mode other
than normal playback mode.
• Pictures in the HDV format may appear
distorted during:
– When a cassette or a “Memory Stick Duo” is
inserted.
– When the POWER switch is set to other than
CAMERA-TAPE.
Continued ,
55
EDIT/PLAY menu (Continued)
STANDARD SET
menu
– Picture search
– Reverse playback
• Playing back slowly to the reverse direction and
playing back frame by frame to the reverse
direction are not available in HDV format.
Settings while recording on a tape or other
basic settings
The default settings are marked with B.
The indicators in parentheses appear when
the items are selected.
See page 39 for details on selecting
menu items.
REC CTRL
(Movie recording control)
VCR HDV/DV
END SEARCH
Select the playback signal. Normally select
[AUTO].
EXEC
When your camcorder is connected to
another device using an i.LINK cable,
select the signal to input/output from the
HDV/DV Interface (i.LINK). The selected
signal is recorded or played back.
The most recently recorded picture is
played back for about 5 seconds and then
stops automatically.
CANCEL
Stops [END SEARCH].
BAUTO
Switches the signals between HDV and
DV format automatically when playing
back a tape.
b Notes
• [END SEARCH] will not work once you eject
the cassette after you have recorded on the tape.
With an i.LINK connection, switches the
signals between HDV and DV formats
automatically, and inputs/outputs from the
HDV/DV Interface (i.LINK).
HDV
Plays back only the portions recorded in
HDV format.
With an i.LINK connection, inputs/outputs
only HDV formatted signals from the
HDV/DV Interface (i.LINK), and records/
plays back. You can also select this when
connecting the camcorder to a computer,
etc.
DV
Plays back only the portions recorded in
DV format.
With an i.LINK connection, inputs/outputs
only DV formatted signals from the
HDV/DV Interface (i.LINK), and records/
plays back. You can also select this when
connecting the camcorder to a computer,
etc.
56
b Notes
b Notes
• Disconnect the i.LINK cable before changing
the [VCR HDV/DV] setting. Otherwise, the
connected device, such as a VCR, may not be
able to recognize the video signal from your
camcorder.
• When [AUTO] is selected, if the signal switches
between HDV and DV formats, the picture and
sound are interrupted temporarily.
• If you record in the LP mode, pictures may
appear mosaic-like or sound may be interrupted
when you play back the tape on other
camcorders or VCRs.
• When you mix recordings in the SP mode and in
the LP mode on one tape, the playback picture
may be distorted or the time code may not be
written properly between the scenes.
• When [i.LINK CONV] is set to [ON HDV t
DV], pictures are output as follows:
x
WIDE SELECT
You can select the aspect ratio according
to the TV connected when recording. Refer
also to the instruction manuals supplied
with your TV.
– at [AUTO], an HDV signal is converted to the
DV format and output; a DV signal is output
as it is.
– at [HDV], an HDV signal is converted to the
DV format and output; a DV signal is not
output.
B16:9 WIDE
Records pictures in the full screen for a
16:9 (wide) TV screen.
– at [DV], a DV signal is output as it is; an
HDV signal is not output.
4:3 (
)
Records pictures in the full screen for a 4:3
TV screen.
REC FORMAT
You can select a recording format.
b Notes
BHDV1080i (
Records in the HDV1080i specification.
)
• Set [TV TYPE] correctly according to the TV
DV (
)
x
AUDIO MODE
Records in the DV format.
B12BIT
b Notes
Records in the 12-bit mode (2 stereo
sounds).
• If you output the recording picture using an
i.LINK cable, set [i.LINK CONV] accordingly.
16BIT (
)
Records in the 16-bit mode (1 stereo sound
with high quality).
DV SET
The following functions are available when
recording in DV format.
b Notes
• When recording in the HDV format, sound is
automatically recorded in [16BIT] mode.
x
REC MODE (Recording mode)
x
AUDIO MIX
BSP (SP)
During tape playback, you can monitor the
sound recorded by other camcorders using
audio dubbing or 4ch microphone
recording.
Records in the SP (Standard Play) mode on
a cassette.
LP (LP)
Increases the recording time to 1.5 times
the SP mode (Long Play).
Continued ,
57
STANDARD SET menu (Continued)
60min
AUDIO MIX
0:00:00:00
LCD/VF SET
The recorded picture will not be affected by
this operation.
x LCD BRIGHT
You can adjust the brightness of the LCD
screen.
ST1
ST2
Touch
/
to adjust the balance of the
original sound (ST1) and the sound
recorded afterwards (ST2), then touch
1 Adjust the brightness with
2 Touch
/
.
.
.
b Notes
x LCD BL LEVEL
You can adjust the brightness of the LCD
screen’s backlight.
• The original sound (ST1) is output at the default
setting.
BNORMAL
Standard brightness.
VOLUME
Touch
(p. 28).
/
to adjust the volume
BRIGHT
Brightens the LCD screen.
z Tips
b Notes
• You can also adjust the setting using the CAM
• When you connect your camcorder to outside
power sources, [BRIGHT] is automatically
selected for the setting.
• When you select [BRIGHT], battery life is
slightly reduced during recording.
MIC LEVEL
You can adjust the recording sound level
manually.
x LCD COLOR
You can adjust the color on the LCD screen
with
BAUTO
/
.
Select to adjust the recording sound level
automatically.
Low intensity
x VF B.LIGHT
You can adjust the brightness of the
viewfinder.
High intensity
MANUAL
Touch
/
to adjust the recording
sound level during recording or standby.
The recording sound level adjustment bars
appear on the screen. The recording sound
level increases as the bar goes to the right.
The recording level meter appears when
the recording sound level is other than
default setting.
BNORMAL
Standard brightness.
BRIGHT
Brightens the viewfinder screen.
b Notes
b Notes
• Use headphones to monitor the sound when
adjusting it.
• When you connect your camcorder to outside
power sources, [BRIGHT] is automatically
selected for the setting.
• When you select [BRIGHT], battery life is
slightly reduced during recording.
58
B16:9
Select to view your pictures on a 16:9
COMPONENT
(wide) TV.
Select [COMPONENT] when connecting
your camcorder to a TV with the
component input jack.
16:9 (wide)
pictures
4:3 pictures
480i
Select when connecting your camcorder to
a TV with the component input jack.
B1080i/480i
4:3
Select when connecting your camcorder to
a TV that has the component input jack
and is capable of displaying the 1080i
signal.
Select to view your pictures on a 4:3
standard TV.
16:9 (wide)
pictures
4:3 pictures
i.LINK CONV
Signals in HDV format are converted to DV
format, and pictures are output in DV
format from the HDV/DV Interface
(i.LINK).
b Notes
• When you connect your camcorder to a TV
compatible with the ID-1 system, and play back
the tape, set [TV TYPE] to [16:9]. The TV
automatically switches the aspect ratio
according to the playback picture. Refer also to
the manual supplied with your TV.
BOFF
Outputs the pictures from the HDV/DV
Interface (i.LINK) in accordance with the
settings in [REC FORMAT] and [VCR
HDV/DV].
• When you connect your camcorder to a TV with
an i.LINK cable to play back the tape, the
setting of [TV TYPE] is invalid.
ON HDV t DV
Pictures in HDV format are converted to
DV format, and pictures in DV format are
output in DV format.
DISP GUIDE (Display guide)
b Notes
See page 110.
• For input signal via an i.LINK connection, see
• Disconnect the i.LINK cable before setting
[i.LINK CONV]. Otherwise, the connected
video device may not be able to recognize the
video signal from your camcorder.
STATUS CHECK
You can check the setup value of the
following items.
– [VCR HDV/DV] (when the POWER switch is
– [COMPONENT] (p. 59)
– [i.LINK CONV] (p. 59)
TV TYPE
You need to convert the signal depending
on the TV connected when playing back the
picture. The recorded pictures are played
back as following illustrations.
– HDMI OUTPUT (p. 103)
Continued ,
59
STANDARD SET menu (Continued)
ASteadyShot off
BExposure
GUIDEFRAME
CWhite balance
DGain
EShutter speed
FAperture value
You can display the frame and check that
the subject is horizontal or vertical by
setting [GUIDEFRAME] to [ON].
The frame is not recorded. Press DISPLAY/
BATT INFO to make the frame disappear.
b Notes
z Tips
• The exposure adjustment value (0EV), a shutter
speed, and the aperture value appear when still
images on a “Memory Stick Duo” are played
back.
• Placing the subject at the cross point of the
guide frame makes a balanced composition.
•
appears for a picture recorded using a flash.
CENTER MARKR
• In the DATE/TIME data display, the date and
time are displayed in the same area. If you
record a picture without setting the clock, [--- --
----] and [--:--:--] will appear.
• During Easy Handycam operation, you can set
only [DATE/TIME].
When you set [CENTER MARKR] to
[ON], the marker is displayed at the center
of the screen so you can identify the center
of the screen easily. The marker is not
recorded. Press DISPLAY/BATT INFO to
make the marker disappear.
REMAINING
COLOR BAR
BAUTO
Displays the remaining tape indicator for
about 8 seconds in situations such as those
described below.
You can display the color bar or record it on
the tape by setting [COLOR BAR] to [ON].
It is convenient to adjust the color on the
monitor connected.
• When you set the POWER switch to PLAY/
EDIT or CAMERA-TAPE with a cassette
inserted.
DATA CODE
• When you touch
(Play/Pause).
During playback, displays the information
(data code) recorded automatically at the
time of recording.
ON
Always displays the remaining tape
indicator.
BOFF
Data code is not displayed.
REMOTE CTRL (Remote control)
DATE/TIME
Displays the date and time.
The default setting is [ON], allowing you to
use the supplied Remote Commander
(p. 106).
CAMERA DATA (below)
Displays camera setting data.
z Tips
60min
0:00:00:00
60min
• Set to [OFF] to prevent your camcorder from
responding to a command sent by remote
control units of other camcorders or VCRs.
1
2
GUIDE
AUTO
100 AWB
3
F1. 8
9dB
P-MENU
6
5
4
60
b Notes
REC LAMP (Recording lamp)
• When you connect your camcorder to a wall
outlet (wall socket), [A.SHUT OFF] is
automatically set to [NEVER].
The camera recording lamp will not light up
during recording when you set this to [OFF]
(The default setting is [ON]).
CALIBRATION
BEEP
BON
QUICK REC (Quick recording)
A beeping sound starts when you start/stop
recording, or operate the touch panel.
OFF
You can slightly reduce the recording start
point time when you start recording by
pressing START/STOP. This function is
useful to compensate for time lapse at the
click of the shutter.
Cancels the beeping sound and shutter
sound.
DISP OUTPUT (Display output)
BOFF
BLCD PANEL
Takes more time to reach the recording
start point, but a smooth transition can be
recorded.
Shows displays such as the time code on
the LCD screen and in the viewfinder.
V-OUT/PANEL
ON (
)
Shows displays such as the time code on
the TV screen, LCD screen, and in the
viewfinder.
Slightly reduces the time it takes to start
recording when you attempt to record right
after you switch on the camcorder (set the
POWER switch to CAMERA-TAPE from
the OFF (CHG) position), or when you
attempt to record when the recording
stanby mode is canceled.
MENU ROTATE
BNORMAL
Scrolls the menu items downwards by
b Notes
touching
.
• If [QUICK REC] is set to [ON], the interval
between scenes freezes for a moment (editing on
your computer is recommended).
OPPOSITE
Scrolls the menu items upwards by
touching
.
z Tips
• If the recording standby mode continues more
than approximately 3 minutes, the drum will
stop rolling, and the standby mode is canceled.
This is to protect the tape and to prevent from
unnecessarily battery exhausting.
A.SHUT OFF (Auto shut off)
B5min
The camcorder is automatically turned off
when you do not operate your camcorder
for more than approximately 5 minutes.
NEVER
The camcorder is not automatically turned
off.
61
TIME/LANGU.
Customizing Personal
Menu
You can add desired menu items to any
Personal Menu, and customize Personal
Menu settings for each POWER lamp
position. This is convenient if you add
frequently used menu items to Personal
Menu.
menu
menu items.
CLOCK SET
WORLD TIME
Adding a menu item
When using your camcorder abroad, you
can set the time difference by touching
You can add up to 28 menu items for each
POWER lamp position. Delete a less
important menu item, if you want to add
more.
/
, the clock will be adjusted in
accordance with the time difference.
If you set the time difference to 0, the clock
returns to the originally set time.
1
Touch
t [ADD].
t [P-MENU SET UP]
LANGUAGE
If the desired menu item is not
You can select the language to be used on
the LCD screen.
displayed, touch
/
.
• Your camcorder offers [ENG[SIMP]]
(simplified English) for when you cannot find
your native tongue among the options.
60min
STBY
Select the category.
0:00:00
END
CAMERA SET
PICT.APPLI.
EDIT/PLAY
STANDARD SET
TIME/LANGU.
OK
2
3
Touch
category, then touch
/
to select a menu
.
60min
Select the item.
STBY
0:00:00
END
SCENE SELECT
SPOT MTR·FCS
SPOT METER
EXPOSURE
WHITE BAL.
OK
Touch
item, then touch
.
/
to select a menu
t [YES] t
The menu item is added to the end of
the list.
62
Deleting a menu item
Arranging the order of menu
items displayed on Personal
Menu
1
Touch
t [DELETE].
t [P-MENU SET UP]
1
Touch
t [SORT].
t [P-MENU SET UP]
If the desired menu item is not
displayed, touch
/
.
If the desired menu item is not
displayed, touch
60min
STBY
Select button to delete.
0:00:00
END
/
.
DISP
GUIDE
MENU
SCENE
SELECT
SMOOTH
SLWREC
1/3
TELE
MACRO
2
3
4
5
Touch the menu item you want to
move.
FADER
2
3
Touch the menu item that you
want to delete.
Touch
/
to move the menu
item to the desired place.
60min
DELETE
STBY
0:00:00
Delete this from
CAMERA-TAPE mode's
P-MENU?
Touch
.
YES
NO
To sort more items, repeat steps 2 to 4.
Touch [END] t
.
Touch [YES] t
.
b Notes
• You cannot move [P-MENU SET UP].
b Notes
• You cannot delete [MENU] and [P-MENU SET
UP].
Initializing the Personal Menu
settings (Reset)
Touch
t [P-MENU SET UP] t
[RESET] t [YES] t [YES] t
.
If the desired menu item is not displayed,
touch
/
.
63
Dubbing/Editing
Dubbing to VCR or DVD/HDD recorders
Connect your camcorder to the wall outlet (wall socket) using the supplied AC Adaptor for
connected.
Connecting to external devices
The connection method and the image quality will differ depending on the VCR or DVD/
HDD recorders and the connectors used.
z Tips
: Signal flow
Camcorder
Cable
External device
HDV1080i compatible
device*
i.LINK cable (supplied)
t HD quality
AV device with i.LINK jack
t SD quality
i.LINK cable (supplied)
A/V connecting cable with
S VIDEO (optional)
AV device with S VIDEO jack
t SD quality
(White)
(Red)
(Yellow)
AV device with audio/video
jacks**
t SD quality
A/V connecting cable
(supplied)
(Yellow)
(White)
(Red)
* An i.LINK jack which is compatible with HDV1080i specification is required. For details, refer to the
instruction manuals supplied with the device to be connected.
**When connecting your camcorder to a monaural device, connect the yellow plug of the A/V connecting
cable to the video jack on the device, and the white (left channel) or red (right channel) plug to the audio
jack on the device.
64
*3 Parts recorded in both DV and HDV format can
be dubbed.
b Notes
• You cannot dub pictures using the HDMI cable.
• Pictures recorded in the DV format are dubbed
as SD (standard definition) images, regardless
of the connection.
b Notes
• When [VCR HDV/DV] is set to [AUTO], and
the signal switches between HDV and DV
formats, the picture and sound are interrupted
temporarily.
Jacks on your camcorder
Open the jack cover and connect the cable.
• When the player and the recorder are both
HDV1080i compatible devices such as HDR-
HC9 and are connected with the i.LINK cable,
after pausing or stopping and then resuming the
recording, the images will be unstable or rough
at that point.
• Set [DISP OUTPUT] to [LCD PANEL] (default
setting) when connecting with an A/V
A/V OUT
HDV/DV
When connecting with the A/V
connecting cable with an S VIDEO
(optional)
1
2
Using an i.LINK cable (supplied)
Connect with S VIDEO jack instead of the
video plug (yellow). This connection
produces pictures more faithfully. The
audio will not be output when you connect
with the S VIDEO cable alone.
Select the required settings from the table
below and make the menu settings.
b Notes
• Disconnect the i.LINK cable before changing
these menu settings, otherwise the VCR or
DVD/HDD recorders may not correctly identify
the video signal.
Dubbing to another device
Menu setting
Recorded Dubbing
1
Prepare your camcorder for
playback.
[VCR HDV/ [i.LINK
format
format
HDV*
DV
DV]
CONV]
[AUTO]
Insert the recorded cassette.
Slide the POWER switch to turn on the
PLAY/EDIT lamp.
1
[OFF]
or HDV
[AUTO]
[AUTO]
HDV
only
[ONHDV
t DV]
1
HDV*
DV
[OFF]
Mixed
HDV
and DV
2
2
When dubbing to the VCR, insert
a cassette for recording.
When dubbing to the DVD
recorder, insert a DVD for
recording.
or HDV*
[ONHDV
t DV]
3
[AUTO]*
[AUTO]
or DV
DV only
DV
–
*1 The VCR or DVD/HDD recorders need to be
compliant with HDV1080i specification.
*2 Parts recorded in DV format cannot be dubbed.
If your recording device has an input
selector, set it to the appropriate input
(such as video input1 and video input2).
Continued ,
65
Dubbing to VCR or DVD/HDD recorders (Continued)
• When dubbing to a DVD recorder from your
camcorder through an i.LINK cable, you may
not operate your camcorder on your DVD
recorder even if its instruction manual says you
can.
If you can set the input mode to HDV or DV on
your DVD recorder and can input/output
pictures, follow the steps in “Dubbing to another
device.”
3
4
Connect your recording device
(VCR or DVD/HDD recorder) to
your camcorder.
Start playback on your
camcorder, and recording on the
recording device.
• When you use an i.LINK cable, the video and
sound signals are transmitted digitally,
producing high quality pictures.
• When an i.LINK cable is connected, the format
Refer to the operating instructions
supplied with your recording device for
details.
of the output signal (
) will be indicated on the LCD screen of
your camcorder.
or
5
When dubbing is complete, stop
your camcorder and the
recording device.
b Notes
• When connecting with an A/V connecting cable,
set [TV TYPE] according to the playback
• To record the date/time and camera settings data
when connected by the A/V connecting cable,
• The following cannot be output via the HDV/
DV interface (i.LINK):
– Indicators
– Pictures edited with [PICT.EFFECT] (p. 54)
or [D.EFFECT] (p. 53)
– Titles that are recorded on other camcorders
• Pictures recorded in the HDV format are not
output from the HDV/DV Interface (i.LINK)
during playback pause or in any playback mode
other than normal playback.
• Note the following when connecting with an
i.LINK cable:
– The recorded picture becomes rough when a
picture is paused on your camcorder while
recording to a VCR or DVD/HDD recorder.
– Data codes (date/time/camera settings data)
may not be displayed or recorded depending
on the device or application.
– You cannot record the picture and sound
separately.
66
Recording pictures from a VCR, etc.
You can record movies from a VCR on a
tape. You can record a scene as a still image
Recording movies
on a “Memory Stick Duo.” Be sure to insert
a cassette or a “Memory Stick Duo” for
recording in your camcorder beforehand.
You can connect your camcorder to a VCR,
etc., or an i.LINK-compatible device using
the i.LINK cable.
Connect your camcorder to the wall outlet
(wall socket) using the supplied AC
also to the instruction manuals supplied
with the devices to be connected.
1
2
Slide the POWER switch to turn
on the PLAY/EDIT lamp.
Set the input signal of your
camcorder.
Set [VCR HDV/DV] to [AUTO] when
recording from an HDV format
compatible device.
HDV1080i
compatible device
AV device with
i.LINK output jack
Set [VCR HDV/DV] to [DV] or
[AUTO] when recording from a DV
format compatible device (p. 56).
3
Connect your VCR, etc as a player
to your camcorder with an i.LINK
cable.
t HD quality
t SD quality
To i.LINK connector
b Notes
• When an i.LINK cable is connected, the
format of the input signal (
or
) will be indicated on the
LCD screen of your camcorder (This
indicator may appear on the screen of the
playback device, however, it will not be
recorded).
: Signal
flow
i.LINK cable
(supplied)
4
5
Insert a cassette into the VCR.
HDV/DV
To HDV/DV
Interface
(i.LINK)
Operate your camcorder to record
movies.
Touch
[REC PAUSE].
t [
REC CTRL] t
If the desired item is not displayed on
the screen, touch
is displayed.
/
until the item
* An i.LINK jack which is compatible with
HDV1080i specification is required.
Continued ,
67
Recording pictures from a VCR, etc. (Continued)
Recording still images
6
Start playing the cassette on your
VCR.
1
Perform steps 1 to 4 in
“Recording movies.”
The picture played on the connected
device appears on the LCD screen of
your camcorder.
2
3
Start playing the cassette.
7
8
9
Touch [REC START] at the point
you want to start recording.
The pictures on the VCR appear on the
screen of your camcorder.
Stop recording.
Press PHOTO lightly at the scene
you want to record. Check the
image and press it fully.
Touch
(Stop) or [REC PAUSE].
Touch
t
.
b Notes
• You cannot record TV programs from the
HDV/DV Interface (i.LINK).
• You can record pictures from DV devices only
in the DV format.
• Note the following when connecting with an
i.LINK cable:
– The recorded picture becomes rough when a
picture is paused on a VCR while recording to
your camcorder.
– You cannot record the picture and sound
separately.
– If you pause or stop the recording and restart
it, the picture may not be recorded smoothly.
• When a 4:3 video signal is input, it appears with
black bands on the right and left sides on the
screen of your camcorder.
68
Dubbing pictures from
a tape to a “Memory
Stick Duo”
You can record a desired scene onto a
“Memory Stick Duo” as a still image, from
a movie you recorded on a tape. Make sure
you have a recorded tape and a “Memory
Stick Duo” inserted into your camcorder.
Deleting recorded
pictures from the
“Memory Stick Duo”
1
Slide the POWER switch
repeatedly to turn on the PLAY/
EDIT lamp.
1
2
Slide the POWER switch
repeatedly to turn on the PLAY/
EDIT lamp.
2
Touch
.
101
1/10
MEMORYY PLAY
60min
101–0001
6.1M
GUIDE
Search and record the scene you
want to record.
P-MENU
Touch
(Play) to play back the
tape, then press PHOTO lightly at the
scene you want to record. Check the
image and press it fully.
3
4
Select a picture you want to
delete with
/
.
Touch
t [YES].
b Notes
• The date and time the picture is recorded on the
tape and stored on the “Memory Stick Duo” are
recorded. On your camcorder, the date and time
the picture is recorded on the tape are displayed.
Camera setting data recorded on the tape cannot
be stored on the “Memory Stick Duo.”
• Still images will be fixed to image size [
1.2M] when playing back in the HDV format.
Still images will be fixed to image size [
0.2M] (16:9) or [VGA (0.3M)] (4:3) when
b Notes
• The pictures cannot be restored once they are
deleted.
• Pictures cannot be deleted when a “Memory
Stick Duo” with the write-protect tab is set to
z Tips
• You cannot record still images while using PB
zoom.
• To delete all pictures at once, select [
ALL
• You can delete pictures on the index screen
be deleted by displaying 6 pictures at once.
Touch
you want to delete t
t [ DELETE] t the picture
t [YES].
69
Marking images on the “Memory Stick Duo”
with specific information
(Print mark/Image protection)
This may change the information of the images
with the Print mark put on using the other
device.
When you are using a “Memory Stick Duo”
with the write-protect tab, make sure the
write-protect tab on the “Memory Stick
Duo” is not set to the write-protect position
(p. 92).
Preventing accidental erasure
(Image protection)
Selecting still images for
printing (Print mark)
You can select and mark images to prevent
accidental erasure.
The DPOF (Digital Print Order Format)
standard is used to select images for
printing on your camcorder.
By marking images that you want to print
out, you do not need to reselect them when
you print them out (You cannot specify the
number of printouts).
1
Slide the POWER switch
repeatedly to turn on the PLAY/
EDIT lamp.
2
3
Touch
[PROTECT].
t
t
t
1
Slide the POWER switch
repeatedly to turn on the PLAY/
EDIT lamp.
Touch the image that you want to
protect.
PROTECT
2
3
Touch
[PRINT MARK].
t
t
t
-
appears.
101–0002
101
Touch the image that you want to
print out later.
2/10
OK
PRINT MARK
4
Touch
t [END].
appears.
101–0002
101
b Notes
2/10
OK
• To cancel image protection, touch the image
again to cancel image protection in step 3.
4
Touch
t [END].
b Notes
• To cancel Print mark, touch the image again to
cancel Print mark in step 3.
• Do not mark images on your camcorder if the
“Memory Stick Duo” already has some images
with the Print mark put on using other devices.
70
Printing recorded images
(PictBridge compliant printer)
You can print out pictures using a
PictBridge compliant printer without
connecting the camcorder to a computer.
6
7
8
Select the number of copies to be
printed with
/
.
A maximum of 20 copies of the image
can be printed.
Connect your camcorder to the AC Adaptor
to obtain power from the wall outlet (wall
Insert the “Memory Stick Duo” containing
still images into your camcorder and turn
on the printer.
Touch
To print the date/time on the image,
touch
t [END].
t [DATE/TIME] t
[DATE] or [DAY&TIME] t
.
1
2
Slide the POWER switch
repeatedly to turn on the PLAY/
EDIT lamp.
Touch [EXEC] t [YES].
When printing is finished, [Printing…]
disappears and the image selection
screen appears again.
Connect the (USB) jack of your
camcorder to the printer using
the USB cable.
To finish printing
Touch [END] on the image selection
screen.
[USB SELECT] appears on the screen
automatically.
b Notes
3
Touch [PictBridge PRINT].
• We cannot guarantee the operation of models
that are not PictBridge compatible.
• Refer also to the operating instructions for the
printer to be used.
• Do not attempt the following operations when
is on the screen. The operations may not be
performed properly.
When connection is complete,
(PictBridge connecting) appears on
the screen.
101
1/10
6.1M
PictBridge PRINT
101-0001
END
– Operate the POWER switch.
– Disconnect the USB cable from the printer or
your camcorder.
+
-
SET EXEC
– Remove the “Memory Stick Duo” from your
camcorder.
One of the images stored on the
“Memory Stick Duo” will be displayed.
• If the printer stops working, disconnect the USB
cable, turn the printer off and on again and
restart the operation from the beginning.
• Some printers may cut off left, right, top and
lower parts of the image. Especially, when the
image is recorded with a 16:9 (wide) ratio, left
and right parts may be largely cut off.
• Some printer models may not support the date/
time printing function. Refer to your printer’s
operating instructions for details.
4
5
Select the image to be printed
with
/
.
Touch
t [COPIES].
Continued ,
71
Printing recorded images (Continued)
• We cannot guarantee the printing of images
recorded with a device other than your
camcorder.
z Tips
• PictBridge is an industry standard established
by the Camera & Imaging Products Association
(CIPA). You can print still images without using
a computer by connecting a printer directly to a
digital video camera or digital still camera,
regardless of model or manufacturer.
• You can also operate by selecting in the
following orders:
–
t [MENU] t
(PICT.APPLI.)
t [USB SELECT] t [PictBridge PRINT].
–
t [MENU] t
t [PictBridge PRINT].
(PICT.APPLI.)
72
Using a Computer
What you can do with Windows computer
When you install the “Picture Motion
x Exporting imported movies from a
Browser” on a Windows computer from the
supplied CD-ROM, you can enjoy the
following operations.
computer to your camcorder
You can send movies which were imported
to the computer back to your camcorder in
HD (high definition) image quality.
b Notes
• You cannot install the supplied software,
“Picture Motion Browser,” on a Macintosh
computer.
About “First Step Guide”
The “First Step Guide” is an instruction
manual you can refer to on your computer.
This describes basic operations, from initial
hookup of your camcorder and computer
and making settings, to general operation
the first time you use the software “Picture
Motion Browser” stored on the CD-ROM
(supplied).
Referring to “Installing the “First Step
Guide”” (p. 75), start the “First Step
Guide,” then follow the instructions.
About the help function of the
software
Main functions
The Help guide explains all the functions of
the software applications. Refer to the Help
guide for further detailed operations after
reading the “First Step Guide” thoroughly.
To display the Help guide, click the [?]
mark on the screen.
x Importing movies taken with your
camcorder
You can import the movies recorded with
HD (high definition) image quality as they
are.
b Notes
x Viewing images imported to a
• You also need to make certain settings on your
camcorder when importing movies to a
computer with commercially available editing
software. For details, refer to “First Step
Guide.”
computer
You can manage movies and still images
by date and time of shooting, and select
movies or still images you want to view as
thumbnails. These thumbnails can be
enlarged and played in a slide show.
• Refer to the following website for the “Picture
Motion Browser” customer support.
http://www.sony.net/support-disoft/
x Editing pictures imported to a
computer
You can edit imported movies and still
images on a computer.
x Creating a disc
You can create a DVD-video with
imported movies. The image quality of the
disc will be SD (standard definition).
Continued ,
73
What you can do with Windows computer (Continued)
ROM drive is necessary for
installation)
System requirements
When using “Picture Motion Browser”
When playing still images recorded on a
“Memory Stick Duo” on a computer
OS: Microsoft Windows 2000
Professional SP4,
OS: Microsoft Windows 2000
Professional SP4,
Windows XP SP2* or
Windows Vista*
Windows XP SP2* or
Windows Vista*
*Except for 64-bit editions.
Standard installation is required.
Operation is not assured if the above
OS has been upgraded.
*64-bit editions and Starter (Edition)
are not supported.
Standard installation is required.
For processing HD footage,
Windows XP SP2 or Windows Vista
is required.
Operation is not assured if the above
OS has been upgraded or in a multi-
boot environment.
Others: USB port (this must be
provided as standard)
b Notes
• Operations are not guaranteed on a computer
environment that does not meet the system
requirements.
• Operations are not guaranteed on all the
recommended environments.
For example, other open or background
applications running on currently may limit
product performance.
• Even in a computer environment where the
operations are guaranteed, frames may be
dropped from movies with HD (high definition)
image quality, resulting in uneven playback.
However, imported images and images on discs
created subsequently will not be affected.
CPU: Intel Pentium 4 2.8 GHz CPU or
faster (Intel Pentium 4 3.2 GHz or
faster, Intel Pentium D, or Intel Core
Duo is recommended.)
For processing SD (standard
definition) image quality content
only, an Intel Pentium III 1 GHz or
faster is necessary.
Application: DirectX 9.0c or later
(This product is based on DirectX
technology. It is necessary to have
DirectX installed.)
Sound system: Direct Sound
• If you use a Notebook PC, connect it to the AC
Adaptor as the power source. Otherwise, the
software will not work properly due to the
power saving function of the PC.
compatible sound card
Memory: 512 MB or more (1 GB or
more is recommended.)
For processing SD (standard
definition) image quality content
only, 256 MB of memory or more is
necessary.
z Tips
• If your computer has a Memory Stick slot, insert
the “Memory Stick Duo” on which still images
are recorded into the Memory Stick Duo
Adaptor (optional), then insert it into the
Memory Stick slot on your computer to copy
still images to the computer.
• When using a “Memory Stick PRO Duo” and
your computer is not compatible with it, connect
your camcorder with the USB cable instead of
using the Memory Stick slot on the computer.
Hard disk:
Disc volume required for
installation: Approximately 500 MB
Display: Minimum 1,024 × 768 dots
Others: USB port (this must be
provided as standard, Hi-Speed USB
(USB 2.0 compatible) is
recommended), DV Interface
(IEEE1394, i.LINK) (to connect via
an i.LINK cable), DVD burner (CD-
74
Installing the “First Step Guide” and software
You need to install the “First Step Guide”
and software to your Windows computer
before connecting your camcorder
to the computer. The installation is
required only for the first time.
4
5
Click [FirstStepGuide].
Select the desired language and
the model name of your
camcorder from the pull-down
menu.
Contents to be installed and procedures
may differ depending on your OS.
z Tips
computer.
Installing the “First Step Guide”
1
2
Confirm that your camcorder is
not connected to the computer.
6
Click [FirstStepGuide(HTML)].
Installation starts.
When [Save is complete] appears, click
[OK] to finish the installation.
Turn on the computer.
b Notes
• Log on as an Administrator for installation.
• Close all applications running on the
computer before installing the software.
To view the “First Step Guide” in PDF
In step 6, click [FirstStepGuide(PDF)].
To install the software “Adobe
Reader” to display the PDF file
In step 6, click [Adobe(R) Reader(R)].
3
Place the supplied CD-ROM in the
disc drive of your computer.
The installation screen appears.
Installing the software
1
Perform steps 1 to 3 in “Installing
If the screen does not appear
1 Click [Start], then click [My
Computer]. (For Windows 2000,
double-click [My Computer].)
2 Double-click [SONYPICTUTIL (E:)]
(CD-ROM) (disc drive).*
2
3
Click [Install].
Select the language for the
application to be installed, then
click [Next].
* Drive names (such as (E:)) may vary
depending on the computer.
Continued ,
75
Installing the “First Step Guide” and software (Continued)
4
Check your area and country/
region, then click [Next].
8
Follow the on-screen instructions
to install the software.
The software to be installed will be
configured according to your country/
region.
Depending on the computer, you may
need to install third party software
(shown below). If the installation screen
appears, follow the instructions to
install the required software.
5
6
7
Read [License Agreement], select
[I accept the terms of the license
agreement] when you agree, then
click [Next].
x Microsoft DirectX 9.0c-Software
required to handle movies
x Windows Media Format 9 Series
Runtime (Windows 2000 only)-Software
required to create a DVD
Restart the computer if required to
complete the installation.
Slide the POWER switch
repeatedly to turn on the PLAY/
EDIT lamp after the connection
confirmation display appears.
9
Remove the CD-ROM from the
disc drive of your computer.
The short-cut icons, such as [
]
Connect your camcorder and
computer with an i.LINK cable or
USB cable.
(“Picture Motion Browser”), appear on
the desktop.
When connecting with a USB
cable, [USB SELECT] appears on
the screen of your camcorder.
Select [
Memory Stick].
Click [Next] after connection is
complete.
z Tips
• For the information about disconnecting the
cable, refer to “First Step Guide.”
A message stating that you need to
restart may appear, but you do not need
to restart at this time. Restart the
computer after the installation is
complete.
76
Viewing “First Step
Guide”
To view “First Step Guide” on your
computer, Microsoft Internet Explorer
Ver.6.0 or later is recommended. Double-
click the short-cut icon for your
camcorder’s “First Step Guide” on the
desktop.
Using a Macintosh
computer
You can copy the still images from the
“Memory Stick Duo” to the Macintosh.
Install “First Step Guide” in the supplied
CD-ROM.
b Notes
• The supplied software “Picture Motion
Browser” does not operate on Mac OS.
z Tips
• You also need to make certain settings on your
camcorder when importing movies to a
computer with commercially available editing
software. For details, refer to “First Step
Guide.”
• You can also start by selecting [Start] t
[Programs] ([All Programs] for Windows XP)
t [Sony Picture Utility] t [FirstStepGuide]
t Your camcorder’s folder t “First Step
Guide” in HTML.
• To view “First Step Guide” in HTML without
installing, copy the desired language folder from
the [FirstStepGuide] folder on the CD-ROM,
and then double-click [Index.html].
• Refer to your camcorder’s “First Step Guide” in
PDF (p. 75) in the following cases:
System requirements
To copy still images from a “Memory
Stick Duo”
– When printing the desired topics of “First
Step Guide”
OS: Mac OS 9.1/9.2 or Mac OS X (v10.1/
v10.2/v10.3/v10.4).
– When “First Step Guide” is not displayed
correctly due to the browser setting even in
recommended environment.
Others: USB port (this must be provided as
standard)
– When the HTML version of “First Step
Guide” cannot be installed.
About “First Step Guide”
The “First Step Guide” is an instruction
manual you can refer to on your computer.
This describes basic operations, from initial
hookup of your camcorder and computer
and making settings, to general operation
the first time you use the software.
Referring to “Installing the “First Step
Guide””, start the “First Step Guide,” then
follow the instructions.
To install “First Step Guide”
Copy “FirstStepGuide(PDF),” stored in the
desired language folder in the
[FirstStepGuide] folder, to your computer.
To view “First Step Guide”
Double-click “FirstStepGuide(PDF).”
If software to view PDF files is not installed
on your computer, download Adobe Reader
from their website, below;
http://www.adobe.com/
77
Troubleshooting
Troubleshooting
If you run into any problems using your
camcorder, use the following table to
troubleshoot the problem. If the problem
persists, disconnect the power source and
contact your Sony dealer.
Settings change during Easy
Handycam operation.
• During Easy Handycam operation, the
settings of the functions that are not
displayed on the screen return to their
• Overall operations/Easy Handycam/
Remote Commander..............................78
• Batteries/Power sources ........................79
• LCD screen/viewfinder .........................79
• Cassette tapes/“Memory Stick Duo”.....80
• Recording ..............................................81
• Playback ................................................83
• Dubbing/Editing/Connecting to other
• Connecting to a computer .....................85
The menu item settings have
changed unexpectedly.
• The following settings return to the default
settings automatically when you set the
POWER switch to OFF (CHG) for more
than 12 hours.
– backlight
– [SCENE SELECT]
– [SPOT MTR·FCS]
– [SPOT METER]
• Functions that cannot be used together
...............................................................85
– [EXPOSURE]
– [WHITE BAL.]
– [SHUTTR SPEED]
– [SPOT FOCUS]
– [FOCUS]
– [ AUDIO MIX] of [DV SET]
– [MIC LEVEL]
Overall operations/Easy
Handycam/Remote Commander
The power does not turn on.
• Attach a charged battery pack to the
• Use the AC Adaptor to connect to a wall
The camcorder gets warm.
• The camcorder may get warmer while you
use it. This is not a malfunction.
The supplied Remote Commander
does not function.
The camcorder does not operate
even when the power is set to on.
• Remove any obstructions between the
Remote Commander and the remote sensor.
• Disconnect the AC Adaptor from the wall
outlet (wall socket) or remove the battery
pack, then reconnect it after about 1 minute.
• Keep strong light sources, such as sunlight
or overhead lighting, away from the remote
sensor, otherwise the Remote Commander
may not function properly.
sharp-pointed object (If you press the
RESET button, all settings are reset, except
Personal Menu items).
• Insert a fresh battery in the compartment
with its +/– terminals matching those of the
Buttons do not work.
• During Easy Handycam operation, not all
78
• Fully charge the battery again. If the
problem persists, the battery may be worn-
• The indicated time may not be correct in
certain circumstances. For example, when
you open or close the LCD panel, it takes
about 1 minute to display the correct
remaining battery time.
Another VCR malfunctions when you
use the supplied Remote
Commander.
• Select a commander mode other than VTR
2 for your VCR.
• Cover the sensor of your VCR with black
paper.
The battery pack discharges too
quickly.
Batteries/Power sources
The power abruptly turns off.
• Ambient temperature is too high or low, or
the battery pack has not been charged
enough. This is not a malfunction.
• Fully charge the battery again. If the
problem persists, the battery may be worn-
• When approximately 5 minutes have
elapsed while you do not operate your
camcorder, the camcorder is automatically
turned off (A.SHUT OFF). Change the
Adaptor.
LCD screen/viewfinder
You cannot turn the LCD backlight
off.
The /CHG (charge) lamp does not
light while the battery pack is being
charged.
• During Easy Handycam operation, you
cannot turn the LCD backlight on/off by
pressing and holding DISPLAY/BATT
• Slide the POWER switch to OFF (CHG)
• Attach the battery pack to the camcorder
• Connect the power cord (mains lead) to the
wall outlet (wall socket) properly.
You cannot turn off the indicator.
• You cannot turn off
. Touch
to
The buttons do not appear on the
touch panel.
The /CHG (charge) lamp flashes
while the battery pack is being
charged.
• Touch the LCD screen lightly.
• Press DISPLAY/BATT INFO on your
camcorder (or DISPLAY on the Remote
• Attach the battery pack to the camcorder
disconnect the AC Adaptor from the wall
outlet (wall socket) and contact your Sony
dealer. The battery pack may be damaged.
The buttons on the touch panel do
not work correctly or do not work at
all.
The remaining battery time indicator
does not indicate the correct time.
• Adjust the touch panel ([CALIBRATION])
• Ambient temperature is too high or too low,
or the battery pack has not been charged
enough. This is not a malfunction.
Continued ,
79
Troubleshooting (Continued)
Menu items are grayed out.
The cassette is noisier during
rewinding or fast-forwarding.
• You cannot select grayed items in the
current recording/playback situation.
• Depending on the functions, you may not
• When using the AC Adaptor, rewind/fast
forward speed increases (compared with
battery operation) and therefore increases
noise. This is not a malfunction.
is not displayed.
You cannot operate functions using
a “Memory Stick Duo,” even if a
“Memory Stick Duo” is inserted.
• During Easy Handycam operation, not all
menu items are functional. Cancel Easy
• Slide the POWER switch to turn on the
CAMERA-MEMORY or PLAY/EDIT
• If you use a “Memory Stick Duo” formatted
on a computer, format it again on your
The picture in the viewfinder is not
clear.
• Move the viewfinder lens adjustment lever
The picture in the viewfinder has
disappeared.
You cannot delete the recorded
picture on the tape.
• Close the LCD panel. The picture is not
displayed in the viewfinder when the LCD
• You cannot delete a recorded picture on
tape; you can only rewind the tape and
record again. The new recording overwrites
the existing one.
Cassette tapes/“Memory Stick
Duo”
You cannot delete pictures or format
a “Memory Stick Duo.”
The cassette cannot be ejected from
the compartment.
• Release the lock on the write-protect tab of
the “Memory Stick Duo” if there is one
• Cancel image protection on the picture
• Make sure the power source (battery pack
or AC Adaptor) is connected correctly
(p. 13).
• Moisture condensation has occurred inside
• The maximum number of pictures that you
can delete on the index screen at one time is
100.
The Cassette Memory indicator or
title display does not appear while
using a cassette with Cassette
Memory.
Image protection cannot be applied,
or you cannot mark pictures for
print.
• This camcorder does not support Cassette
Memory, so the indicator does not appear.
• Release the lock on the write-protect tab of
the “Memory Stick Duo” if there is one
• Perform the operation again on the index
• The maximum number of pictures you can
mark for print is 999.
The remaining tape indicator is not
displayed.
• Set [
REMAINING] to [ON] to always
80
The data file name is not indicated
correctly, or flashes.
The recording image view looks
different.
• The file is damaged.
• Use the file format compatible with your
• The recording image view may look
different depending on the condition of
your camcorder. This is not a malfunction.
You cannot record a smooth
transition on a tape from the last
recorded scene to the next.
Recording
Refer also to “Cassette tapes/“Memory
Stick Duo”” section (p. 80).
• Perform END SEARCH (p. 32).
• Do not remove the cassette (The picture
will be recorded continuously without a
break even when you turn the power off).
The tape does not start when you
press START/STOP.
• Do not record pictures in the HDV and DV
formats on the same tape.
• Do not record pictures in SP mode and LP
mode on the same tape.
• Avoid stopping then recording a movie in
the LP mode.
• When [QUICK REC] is set to [ON], you
• Slide the POWER switch to turn on the
• The tape has reached the end. Rewind it, or
insert a new cassette.
• Set the write-protect tab to REC or insert a
• The tape is stuck to the drum due to
moisture condensation. Remove the
cassette and leave your camcorder for at
least 1 hour, then reinsert the cassette
The flash does not work.
• You cannot use the flash during tape
recording.
You cannot record on the “Memory
Stick Duo.”
• Even if auto flash or
(Auto redeye
reduction) is selected, you cannot use the
internal flash with:
• The “Memory Stick Duo” is full. Insert
another “Memory Stick Duo” or format the
unnecessary pictures recorded on the
• When the POWER switch is set to
CAMERA-TAPE, you cannot record still
images on the “Memory Stick Duo” with:
– When [SHUTTR SPEED] is set between
1/725 to 1/10000 second
– [TWILIGHT], [CANDLE], [SUNRSE
SUNSET], [FIREWORKS],
[LANDSCAPE], [SPOTLIGHT],
[BEACH] or [SNOW] of [SCENE
SELECT]
– [SPOT MTR·FCS]
– [SPOT METER]
– [MANUAL] of [EXPOSURE]
– While executing [FADER]
– [D.EFFECT]
– [PICT.EFFECT]
– [SMTH SLW REC]
– [COLOR BAR]
[END SEARCH] does not work.
• Do not eject the cassette after recording
• There is nothing recorded on the cassette.
• There is a blank section between recorded
sections of the tape. This is not a
malfunction.
Continued ,
81
Troubleshooting (Continued)
[COLOR SLOW S] does not operate
correctly.
The subjects passing fast by the
frame might appear crooked.
• [COLOR SLOW S] may not operate
correctly in total darkness. Use NightShot
or [SUPER NS].
• This is called the focal plane phenomenon.
This is not a malfunction. Because of the
way the image device (CMOS sensor) reads
out image signals, the subjects passing in
front of the lens rapidly might appear
crooked depending on the recording
conditions.
You cannot use [SUPER NS].
• The NIGHTSHOT switch is not set to ON
(p. 27).
The color of the picture is not
correctly displayed.
The auto focus does not function.
• The recording conditions are not suitable
for auto focus. Adjust the focus manually
(p. 45).
The screen picture is bright, and the
subject does not appear on the
screen.
[STEADYSHOT] does not function.
OFF, or cancel the backlight function
• Set [STEADYSHOT] to [ON] (p. 48).
The backlight function does not
function.
The screen picture is dark, and the
subject does not appear on the
screen.
• The backlight function does not work
• Press and hold DISPLAY/BATT INFO for
a few seconds to turn on the backlight
The [FLASH LEVEL] cannot be
changed.
changed during Easy Handycam operation.
Horizontal bands appear.
• This may occur when recording pictures
under lighting from a discharge tube, such
as a fluorescent lamp, sodium lamp, or
mercury lamp. This is not a malfunction.
• This may be alleviated by adjusting the
Tiny spots in white, red, blue, or
green appear on the screen.
• The spots appear when the shutter speed is
slow or when you are recording in [SUPER
NS] or [COLOR SLOW S]. This is not a
malfunction.
Black bands appear when you
record a TV screen or computer
screen.
82
Playback
No sound or only a low sound is
heard.
Refer also to “Cassette tapes/“Memory
Stick Duo”” section (p. 80).
• Adjust [ AUDIO MIX] from the [ST2]
(additional sound) side until the sound is
You cannot play back a tape.
• If you are using an S VIDEO plug or
component video plug, make sure the red
and white plugs of the A/V connecting
• Slide the POWER switch to turn on the
PLAY/EDIT lamp.
• Sounds cannot be recorded while shooting a
3 second-movie (approx.) using [SMTH
SLW REC].
You cannot play back in reverse
direction.
• Reverse playback is not possible with the
tape recorded in the HDV format.
The picture or sound breaks off.
• The tape was recorded in both the HDV and
DV formats. This is not a malfunction.
Image data stored on a “Memory
Stick Duo” cannot be played back.
• Image data cannot be played back if you
have modified file names or folders, or
have edited the data on a computer (In this
case, the file name flashes). This is not a
• Pictures recorded on other devices may not
be played back or may not appear in their
actual size. This is not a malfunction
The movies freeze for a while, or the
sound breaks off.
• This occurs if the tape or video head is dirty
• Use the Sony mini DV cassette.
“---” is displayed on the screen.
• The tape you are playing was recorded
without setting the date and time.
Horizontal lines appear on the
picture. The displayed pictures are
not clear or do not appear.
• A blank section on the tape is being played.
• The data code on a tape with a scratch or
noise cannot be read.
• Clean the head using the cleaning cassette
Noises appear and
or
is
displayed on the screen.
You cannot hear the sound recorded
with 4CH MIC REC on another
camcorder.
• The tape was recorded in a TV color system
other than that of your camcorder (NTSC).
Date Search does not work correctly.
Fine patterns flicker, diagonal lines
look jagged.
• Be sure to record more than 2 minutes after
the date changed. If one day’s recording is
too short, your camcorder may not
accurately find the point where the
recording date changes.
• Adjust [SHARPNESS] to the
(soften)
Continued ,
83
Troubleshooting (Continued)
• There is a blank section between recorded
sections of the tape. This is not a
malfunction.
You cannot view the picture or hear
the sound on the TV connected with
the HDMI cable.
• Pictures in the DV format are not output
from the HDMI OUT jack, if copyright
protection signals are recorded in the
pictures.
• DV format pictures input to the camcorder
No picture appears during [END
SEARCH] or Rec Review.
• The tape was recorded in both HDV and
DV formats. This is not a malfunction.
• This occurs if you record on a tape in both
HDV and DV formats. Disconnect and
connect the HDMI cable, or slide the
POWER switch to turn on your camcorder
again.
appears on the LCD screen.
• This appears when you play back a tape
recorded on other recording devices using a
4ch microphone (4CH MIC REC). This
camcorder does not comply with the 4ch
microphone recording standard.
The picture appears distorted on a
4:3 TV.
Playing back on TV
• This happens when viewing a picture
recorded in the 16:9 (wide) mode on a 4:3
TV. Set [TV TYPE] on the
back the picture.
You cannot view the picture on the
TV connected with the i.LINK cable.
• You cannot view the picture in the HD
(high definition) image quality on the TV
which is not compatible with the
the instruction manuals supplied with your
TV.
• Down convert the pictures recorded in
HDV format to DV format and play back in
SD (standard definition) image quality
(p. 59).
Black bands appear at the top and
bottom on a 4:3 TV.
• This happens when viewing a picture
recorded in 16:9 (wide) mode on a 4:3 TV.
This is not a malfunction.
Dubbing/Editing/Connecting to
other devices
• Play back pictures using another connecting
Pictures from connected devices
cannot be zoomed.
You cannot view the picture or hear
the sound on the TV connected with
the component video cable.
• You cannot zoom pictures from connected
• Set [COMPONENT] on the
(STANDARD SET) menu according to the
requirements of the connected device
(p. 59).
• When you are using the component video
cable, make sure the red and white plugs of
the A/V connecting cable are connected
(p. 34).
Time code and other information
appear on the display of the
connected device.
• Set [DISP OUTPUT] to [LCD PANEL]
while connected with an A/V connecting
84
You cannot dub correctly using the
A/V connecting cable.
Still pictures cannot be dubbed from
a tape to a “Memory Stick Duo.”
• You cannot input externally from a device
connected with the A/V connecting cable.
• The A/V connecting cable is not connected
properly.
• You cannot record or a distorted picture
may be recorded if the tape has been used
repeatedly for recording.
Make sure that the A/V connecting cable is
connected to the input jack of the other
device for dubbing a picture from your
camcorder.
Connecting to a computer
The computer does not recognize
your camcorder.
When connected using an i.LINK
cable, no picture appears on the
monitor screen or the picture is
distorted during dubbing.
• Disconnect USB devices other than the
keyboard, the mouse, and the camcorder
from the (USB) jack on the computer.
• Disconnect the cable from the computer
and camcorder, restart the computer, then
connect them again correctly.
• Set [VCR HDV/DV] on the
(STANDARD SET) menu according to the
requirements of the connected device
• If the device to be connected is not
compatible with HDV1080i specification,
you cannot dub in HD (high definition)
the instruction manuals supplied with the
device to be connected.
You cannot install the supplied
software, “Picture Motion Browser,”
on a Macintosh computer.
• You cannot use “Picture Motion Browser”
on a Macintosh computer.
• Down convert the pictures recorded in
HDV format to DV format and dub in SD
Functions that cannot be used
together
Depending on the functions, you may not be
able to use them together. The following list
shows examples of menu items and functions
that cannot be used at the same time.
You cannot add sound to the
recorded tape.
• You cannot add sound to the recorded tape
on this unit.
Not available
If this function is set
backlight function
[FIREWORKS],
[SPOT METER],
[MANUAL] of
[EXPOSURE]
You cannot dub correctly using the
HDMI cable.
• You cannot dub pictures using the HDMI
cable.
[SCENE SELECT]
NightShot, [TELE
MACRO],
[SUPER NS],
New sound added to a recorded tape
on another camcorder is not heard.
[CINEMA EFECT],
[OLD MOVIE],
[COLOR SLOW S]
• Adjust [ AUDIO MIX] from the [ST1]
(original sound) side until the sound is
Continued ,
85
Troubleshooting (Continued)
Not available
If this function is set
Not available
If this function is set
[SPOT MTR·FCS]
NightShot,
[D.EFFECT]
[CANDLE],
[SUPER NS],
[CINEMA EFECT]
[SCENE SELECT]
[FIREWORKS],
[SUPER NS],
[COLOR SLOW S],
[FADER]
[SPOT METER]
[EXPOSURE]
NightShot,
[SUPER NS],
[CINEMA EFECT]
[OLD MOVIE] of
[D.EFFECT]
[SCENE SELECT],
[PICT.EFFECT],
when [ WIDE
SELECT] is set to
[4:3]
NightShot,
[SUPER NS],
[CINEMA EFECT]
[CINEMA EFECT] [SCENE SELECT],
[WHITE BAL.]
[SHARPNESS]
NightShot, [SUPER
NS]
of [D.EFFECT]
[SPOT METER],
[MANUAL] of
[EXPOSURE], other
than 0 in [AE
SHIFT],
[CINEMA EFECT]
[SHUTTR SPEED]
of the CAM CTRL
dial
NightShot,
[SUPER NS],
[CINEMA EFECT],
[OLD MOVIE],
[SMTH SLW REC]
[PICT.EFFECT],
when [ WIDE
SELECT] is set to
[4:3]
[AE SHIFT]
[FIREWORKS],
[MANUAL] of
[EXPOSURE],
[SMTH SLW REC] [CANDLE],
[FIREWORKS],
[CINEMA EFECT]
[MANUAL] of
[SHUTTR SPEED],
[SUPER NS],
[COLOR SLOW S],
[D.EFFECT],
[SPOT FOCUS]
[TELE MACRO]
[SCENE SELECT]
[SCENE SELECT],
during tape recording
[COLOR SLOW S] NightShot, [SCENE
SELECT],
[PICT.EFFECT]
[MANUAL] of
[SHUTTR SPEED],
[SUPER NS],
• When [COLOR BAR] is set, all the “Not
available” menu items on the list are not
available.
[FADER],
[D.EFFECT]
[HISTOGRAM]
[DIGITAL ZOOM],
[D.EFFECT], while
displaying the date
and time
[DIGITAL ZOOM] [TELE MACRO]
[FADER]
[CANDLE],
[FIREWORKS],
[SUPER NS],
[COLOR SLOW S],
[D.EFFECT]
86
Warning indicators and messages
E:61:ss / E:62:ss / E:91:ss
Self-diagnosis display/Warning
indicators
• Contact your Sony dealer or local
authorized Sony service facility. Inform
them of the 5-digit code, which starts
from “E.”
If indicators appear on the LCD screen or in
the viewfinder, check the following.
Some symptoms you can fix by yourself. If
the problem persists even after you have
tried a couple of times, contact your Sony
dealer or local authorized Sony service
facility.
101-1001(Warning indicator
pertaining to files)
• The file is damaged.
C:(or E:) ss:ss (Self-diagnosis
display)
E (Battery level warning)
• The battery pack is nearly used up.
C:04:ss
• The battery pack is not an
“InfoLITHIUM” battery pack (H
series). Use an “InfoLITHIUM” battery
• Depending on the operating,
environment, or battery conditions, E
may flash, even if there are
approximately 5 to 10 minutes
remaining.
• Connect the DC plug of the AC
Adaptor to the DC IN jack of your
% (Moisture condensation warning)*
• Eject the cassette, remove the power
source, and then leave it for about 1
C:21:ss
• Moisture condensation has occurred.
Remove the cassette and leave your
camcorder for at least 1 hour, then re-
(Warning indicator pertaining to
“Memory Stick Duo”)
C:22:ss
• Clean the head using a cleaning
• A “Memory Stick Duo” is not inserted
(p. 19).
C:31:ss / C:32:ss
(Warning indicators pertaining to
“Memory Stick Duo” formatting)*
• Symptoms that are not described above
have occurred. Remove and insert the
cassette, then operate your camcorder
again. Do not perform this procedure if
moisture condensation has occurred
• The “Memory Stick Duo” is damaged.
• The “Memory Stick Duo” is not
• Remove the power source. Reconnect it
and operate your camcorder again.
• Change the cassette. Press RESET
again.
(Warning indicator pertaining to
incompatible “Memory Stick Duo”)*
• An incompatible “Memory Stick Duo”
Continued ,
87
Warning indicators and messages (Continued)
* You hear a melody when the warning indicators
Q (Warning indicators pertaining to
the tape)
Slow flashing:
• There is less than 5 minutes remaining
on the tape.
Description of warning
messages
If messages appear on the screen, follow the
instructions.
• No cassette is inserted.*
• The write-protect tab on the cassette is
z Tips
• When
turned into
Fast flashing:
• The tape has run out.*
is displayed, the message can be
by touching . Touch
to display the message again.
Z (Eject cassette warning)*
x Moisture condensation
Slow flashing:
• The write-protect tab on the cassette is
%Z Moisture condensation. Eject
Fast flashing:
• Moisture condensation has occurred
(p. 96).
• The self-diagnosis display code is
% Moisture condensation. Turn off
x Cassette/Tape
- (Warning indicator pertaining to
image deletion)*
• Check if the cassette is damaged.
- (Warning indicator pertaining
to the write-protect of the “Memory
Stick Duo”)*
QZ The tape is locked - check the
• The write-protect tab on the “Memory
(Warning indicator pertaining to
the flash)
Slow flashing:
• Still charging
Fast flashing:
• The self-diagnosis display code is
• There is something wrong with the
flash.
88
x “Memory Stick Duo”
Reinsert the Memory Stick.
• Reinsert the “Memory Stick Duo” a
few times. If even then the indicator
flashes, the “Memory Stick Duo” might
be damaged. Try with another
“Memory Stick Duo.”
This Memory Stick is not
formatted correctly.
• Check the format, then format the
“Memory Stick Duo” as necessary
Memory Stick folders are full.
• You cannot create folders exceeding
999MSDCF. You cannot delete created
folders using your camcorder.
• You will have to format the “Memory
your computer.
x Dual Rec
Cannot save still picture.
• Do not eject “Memory Stick Duo”
while still images are being stored onto
x PictBridge compliant printer
Check the connected device.
• Switch off the printer and switch it on
again, then disconnect the USB cable
and reconnect it.
Cannot print. Check the printer.
• Switch off the printer and switch it on
again, then disconnect the USB cable
and reconnect it.
89
Additional Information
Using your camcorder abroad
Power supply
You can use your camcorder in any
Viewing HDV format pictures recorded
in HDV format
country/region using the AC Adaptor
supplied with your camcorder within the
AC 100 V to 240 V, 50/60 Hz range.
Use a commercially available AC plug
adaptor [a], if necessary, depending on the
design of the wall outlet (wall socket) [b].
You need an HDV1080i compatible TV (or
monitor) with a component jack and
AUDIO/VIDEO input jack. A component
video cable and A/V connecting cable are
also needed.
Viewing DV format pictures recorded
in DV format
You need a TV (or monitor) with the
AUDIO/VIDEO input jack. A connecting
cable is also needed.
AC-L200/L200B
[a]
[b]
On TV color systems
Your camcorder is NTSC system, so its
Simple setting of the clock by time
difference
You can easily set the clock to the local
time abroad by entering the time difference
between where you live and where you are.
picture can only be viewed on an NTSC
system TV with an AUDIO/VIDEO input
jack.
System
Used in
NTSC
Bahama Islands, Bolivia,
Canada, Central America, Chile,
Colombia, Ecuador, Guyana,
Jamaica, Japan, Korea, Mexico,
Peru, Surinam, Taiwan,
Select [WORLD TIME] in the
LANGU.) menu, then set the time
difference (p. 62).
(TIME/
the Philippines, the U.S.A.,
Venezuela, etc.
PAL
Australia, Austria, Belgium,
China, Czech Republic,
Denmark, Finland, Germany,
Holland, Hong Kong, Hungary,
Italy, Kuwait, Malaysia,
New Zealand, Norway, Poland,
Portugal, Singapore,
Slovak Republic, Spain,
Sweden, Switzerland, Thailand,
United Kingdom, etc.
PAL - M Brazil
PAL - N Argentina, Paraguay, Uruguay.
SECAM Bulgaria, France, Guiana, Iran,
Iraq, Monaco, Russia, Ukraine,
etc.
90
Maintenance and precautions
Copyright signal
Usable cassette tapes
x When you play back
Your camcorder is capable of recording in
both HDV and DV formats.
You can use mini DV format cassettes only.
Use a cassette with the
Your camcorder is not compatible with the
Cassette Memory function.
If the cassette you play back on your
camcorder contains copyright signals, you
cannot copy it to a tape in another video
camera connected to your camcorder.
mark.
x When you record
You cannot record software on your
camcorder that contains copyright control
signals for copyright protection of software.
[Cannot record due to copyright
protection.] appears on the LCD screen, or
on the viewfinder if you try to record such
software. Your camcorder does not record
copyright control signals on the tape when
it records.
What is the HDV format?
The HDV format is a video format
developed to record and play back digital
high definition (HD) video signals on a DV
cassette.
Your camcorder adopts the Interlace mode
with 1,080 effective scan lines of screen
ruling (1080i, number of pixels 1,440 ×
1,080 dots).
The video bit rate for recording is about 25
Mbps.
i.LINK is adopted for the digital interface,
enabling a digital connection with an HDV
compatible TV or computer.
Notes on use
x When not using your camcorder for a
long time
Remove the cassette and store it.
x To prevent accidental erasure
Slide the write-protect tab on the cassette to
set it to SAVE.
z Tips
• HDV signals are compressed in MPEG2 format,
which is adopted in BS (broadcast satellite)
digital, terrestrial digital HDTV broadcastings,
in Blu-ray Disc recorders, etc.
Playback
Your camcorder can play back pictures in
both the DV format and HDV1080i
specification.
Your camcorder can play back pictures
recorded in the HDV 720/30p format, but
cannot output it from the HDV/DV
Interface (i.LINK).
REC: The cassette can be
recorded.
SAVE: The cassette cannot be
recorded (write-protected).
REC
SAVE
To prevent a blank section from being
created on the tape
Go to the end of the recorded section using
next recording when you have played back
the tape.
Continued ,
91
Maintenance and precautions (Continued)
x When labeling the cassette
Recording/
Playback
Types of “Memory Stick”
Be sure to place the label only on the
locations shown in the following
illustration so as not to cause a malfunction
of your camcorder.
“Memory Stick Duo”
(with MagicGate)
a
“Memory Stick PRO Duo”
a
Do not put a label
along this border.
“Memory Stick PRO-HG Duo”
a*
* This product does not support 8-bit parallel data
transfer but it supports 4-bit parallel data
transfer the same as with Memory Stick PRO
Duo.
Labeling position
• This product cannot record or play data that uses
“MagicGate” technology. “MagicGate” is a
copyright protection technology that records and
transfers the contents in an encrypted format.
• This product is compatible with “Memory Stick
Micro” (“M2”). “M2” is the abbreviation for the
“Memory Stick Micro.”
x After using the cassette
Rewind the tape to the beginning to avoid
distortion of the picture or the sound. The
cassette should then be put in its case, and
stored in an upright position.
• Still image format: Your camcorder compresses
and records image data in the JPEG (Joint
Photographic Experts Group) format. The file
extension is “.JPG.”
• File names of still images:
– 101- 0001: This file name appears on the
screen of your camcorder.
x When cleaning the gold-plated
connector
Generally, clean the gold-plated connector
on a cassette with a cotton-wool swab after
every 10 times it has been ejected.
If the gold-plated connector on the cassette
is dirty or dusty, the remaining tape
indicator may not show correctly.
– DSC00001.JPG: This file name appears on
the display of a computer.
• A “Memory Stick Duo” formatted by a
computer (Windows OS/Mac OS) does not have
guaranteed compatibility with your camcorder.
• Data read/write speed may vary depending on
the combination of the “Memory Stick” and
“Memory Stick” compliant product you use.
Gold-plated connector
• You can prevent accidental erasure of images
when you slide the write-protect tab on the
“Memory Stick Duo” with a small tapered
object, to the write-protect position.
About the “Memory Stick”
A “Memory Stick” is a compact, portable
IC recording medium with a large data
capacity.
You can use the following types of
“Memory Stick” in your camcorder.
However, we do not guarantee the
operation of all types of “Memory Stick” in
your camcorder.
• Damaged or lost image data will not be
compensated for, and may occur in the
following cases:
– If you eject the “Memory Stick Duo,” turn the
power off on your camcorder, or remove the
battery pack for replacement while your
camcorder is reading or writing image files on
the “Memory Stick Duo” (while the access
lamp is lit or flashing).
– If you use the “Memory Stick Duo” near
magnets or magnetic fields.
92
• It is recommended you make a back-up of
important data on the hard disk of a computer.
• Be careful not to apply excessive force when
writing on a memo area on a “Memory Stick
Duo.”
• Do not attach a label or the like on a “Memory
Stick Duo” or a Memory Stick Duo adaptor.
• When you carry or store a “Memory Stick Duo,”
put it in its case.
Notes on using “Memory Stick Micro”
• To use a “Memory Stick Micro” with the VCR,
you need a Duo-sized M2 Adaptor. Insert the
“Memory Stick Micro” into the Duo-sized M2
Adaptor, then insert the adaptor into the
Memory Stick Duo slot. If you insert a
“Memory Stick Micro” into the VCR without
using a Duo-sized M2 Adaptor, you might not
be able to remove it from the VCR.
• Do not touch, or allow metallic objects to come
into contact with the terminals.
• Do not bend, drop or apply strong force to the
“Memory Stick Duo.”
• Do not leave the “Memory Stick Micro” within
the reach of small children. They might
accidentally swallow it.
On image data compatibility
• Do not disassemble or modify the “Memory
Stick Duo.”
• Do not let the “Memory Stick Duo” get wet.
• Be careful to keep “Memory Stick Duo” media
out of the reach of small children. There is
danger that a child might swallow it.
• Do not insert anything other than a “Memory
Stick Duo” into the Memory Stick Duo slot.
Doing so may cause a malfunction.
• Do not use or keep the “Memory Stick Duo” in
the following locations.
– Places subject to extremely high temperature,
such as a car parked outside in the summer.
– Places under direct sunlight.
– Places with extremely high humidity or
subject to corrosive gases.
• Image data files recorded on a “Memory Stick
Duo” by your camcorder conform to the
“Design rule for Camera File system” universal
standard established by the JEITA (Japan
Electronics and Information Technology
Industries Association).
• On your camcorder, you cannot play back still
images recorded on other devices (DCR-
TRV900 or DSC-D700/D770) that do not
conform to the universal standard (These
models are not sold in some regions).
• If you cannot use a “Memory Stick Duo” that
has been used with another device, format it
formatting erases all information on the
“Memory Stick Duo.”
• You may not be able to play back images with
your camcorder:
– When playing back image data modified on
your computer.
– When playing back image data recorded with
other devices.
x On the Memory Stick Duo adaptor
• When using a “Memory Stick Duo” with a
“Memory Stick” compliant device, be sure to
insert the “Memory Stick Duo” into a Memory
Stick Duo adaptor.
• When inserting a “Memory Stick Duo” into a
Memory Stick Duo adaptor, make sure the
“Memory Stick Duo” is inserted facing in the
correct direction, then insert it all the way in. If
you force the “Memory Stick Duo” into the
Memory Stick Duo adaptor in the wrong
direction or insert it incompletely, it may cause
a malfunction.
About the “InfoLITHIUM”
battery pack
This unit is compatible with an
“InfoLITHIUM” battery pack (H series).
Your camcorder operates only with an
“InfoLITHIUM” battery pack.
• Do not insert a Memory Stick Duo adaptor
without a “Memory Stick Duo” attached. Doing
so may result in malfunctions of the unit.
“InfoLITHIUM” H series battery packs
have the
mark.
x On a “Memory Stick PRO Duo”
• The maximum memory capacity of a “Memory
Stick PRO Duo” that can be used on your
camcorder is 8 GB.
Continued ,
93
Maintenance and precautions (Continued)
consumed when your camcorder is in recording
standby or playback pause.
What is an “InfoLITHIUM” battery
pack?
An “InfoLITHIUM” battery pack is a
lithium-ion battery pack that has functions
for communicating information related to
operating conditions between your
camcorder and an optional AC Adaptor/
charger.
The “InfoLITHIUM” battery pack
calculates the power consumption
according to the operating conditions of
your camcorder, and displays the remaining
battery time in minutes.
• Have spare battery packs ready for two or three
times the expected recording time, and make
trial recordings before making the actual
recording.
• Do not expose the battery pack to water. The
battery pack is not water resistant.
About the remaining battery time
indicator
• When the power goes off even though the
remaining battery time indicator indicates that
the battery pack has enough power to operate,
charge the battery pack fully again. Remaining
battery time will be indicated correctly. Note,
however, that the battery indication will not be
restored if it is used in high temperatures for a
long time, or if left in a fully charged state, or
when the battery pack is frequently used. Use
the remaining battery time indication as a rough
guide only.
With an AC Adaptor/charger, the remaining
battery time and charging time appear.
To charge the battery pack
• Be sure to charge the battery pack before you
start using your camcorder.
• We recommend charging the battery pack in an
ambient temperature of between 10 °C to 30 °C
(50 °F to 86 °F) until the /CHG (charge) lamp
turns off. If you charge the battery pack outside
of this temperature range, you may not be able
to charge it efficiently.
• The E mark that indicates low battery flashes
even if there are still 5 to 10 minutes of battery
time remaining, depending on the operating
conditions or ambient temperature.
• After charging is complete, disconnect the cable
from the DC IN jack on your camcorder or
remove the battery pack.
About storage of the battery pack
• If the battery pack is not used for a long time,
fully charge the battery pack and use it up on
your camcorder once a year to maintain proper
function. To store the battery pack, remove it
from your camcorder and put it in a dry, cool
place.
To use the battery pack effectively
• Battery pack performance decreases when the
surrounding temperature is 10 °C (50 °F) or
below, and the length of time you can use the
battery pack becomes shorter. In that case, do
one of the following to use the battery pack for a
longer time.
– Put the battery pack in a pocket to warm it up,
and insert it in your camcorder right before
you start taking shots.
• To discharge the battery pack on your
camcorder completely, set [A.SHUT OFF] to
[NEVER] on the
(STANDARD SET)
menu and leave your camcorder in tape
recording standby until the power goes off
(p. 61).
About battery life
– Use a large capacity battery pack: NP-FH70/
FH100 (optional).
• Frequent use of the LCD screen or a frequent
playback, fast forward or rewind operation
wears out the battery pack faster.
We recommend using a large capacity battery
pack: NP-FH70/FH100 (optional).
• Be sure to set the POWER switch to OFF
(CHG) when not recording or playing back on
your camcorder. The battery pack is also
• Battery capacity decreases over time and
through repeated use. If decreased usage time
between charges becomes significant, it is
probably time to replace it with a new one.
• Each battery’s life is governed by storage,
operating and environmental conditions.
94
S200 (approx. 200Mbps)
S400 (approx. 400Mbps)
About i.LINK
The HDV/DV Interface on this unit is an
i.LINK-compliant Interface. This section
describes the i.LINK standard and its
features.
The baud rate is listed under
“Specifications” in the operating
instructions of each piece of equipment. It
is also indicated near the i.LINK interface
on some devices.
The baud rate may differ from the indicated
value when the unit is connected to a device
with a different maximum baud rate.
What is i.LINK?
i.LINK is a digital serial interface for
transferring digital video, digital audio, and
other data to other i.LINK-compatible
devices. You can also control other devices
using the i.LINK.
i.LINK-compatible devices can be
connected using an i.LINK cable. Possible
applications are operations and data
transactions with various digital AV
devices.
* What is Mbps?
Mbps stands for “megabits per second,” or
the amount of data that can be sent or
received in one second. For example, a
baud rate of 100 Mbps means that 100
megabits of data can be sent in one second.
When two or more i.LINK-compatible
devices are daisy-chained with the unit,
operation becomes possible from any
device in the chain. Note that operation
method may vary, or data transactions may
not be possible, depending on specifications
and characteristics of the connected
devices.
To use i.LINK functions on this unit
For details on how to dub when this unit is
connected to other video devices having an
This unit can also be connected to other
i.LINK-compatible devices made by Sony
(e.g. a VAIO series personal computer) as
well as to video devices.
Some i.LINK compatible video devices,
such as Digital Televisions, DVD,
b Notes
• Normally, only one device can be connected to
this unit with an i.LINK cable. When
connecting this unit to an HDV/DV compatible
device having two or more HDV/DV
Interfaces, refer to the operating instructions of
the device to be connected.
MICROMV or HDV recorders/players are
not compatible with this unit. Before
connecting to other devices, be sure to
confirm whether the device is compatible
with an HDV/DV device or not. For details
on precautions and compatible application
software, refer also to the operating
instructions for the device to be connected.
z Tips
• i.LINK is a more familiar term for the
IEEE1394 data transport bus proposed by Sony,
and is a trademark approved by many
corporations.
b Notes
• When connecting your camcorder to another
i.LINK-compatible device, be sure to turn off
the power of the device and disconnect the AC
Adaptor from the wall outlet (wall socket)
before connecting or disconnecting the i.LINK
cable.
• IEEE1394 is an international standard
standardized by the Institute of Electrical and
Electronics Engineers.
About the i.LINK Baud rate
i.LINK’s maximum baud rate varies
according to the device. There are 3 types.
S100 (approx. 100Mbps*)
Continued ,
95
Maintenance and precautions (Continued)
checked by a Sony dealer before operating it
any further.
About the required i.LINK cable
Use the Sony i.LINK 4-pin-to-4-pin cable
(during HDV/DV dubbing).
• Avoid rough handling, disassembling,
modifying, physical shock, or impact such as
hammering, dropping or stepping on the
product. Be particularly careful of the lens.
• Keep the POWER switch setting to OFF (CHG)
when you are not using your camcorder.
• Do not wrap your camcorder with a towel, for
example, and operate it. Doing so might cause
heat to build up inside.
• When disconnecting the power cord (mains
lead), pull it by the plug and not the cord.
About x.v.Color
• x.v.Color is a more familiar term for the xvYCC
standard proposed by Sony, and is a trademark
of Sony.
• xvYCC is an international standard for color
space in video. This standard can express a
wider color range than the currently used
broadcast standard.
• Do not damage the power cord (mains lead)
such as by placing anything heavy on it.
• Keep metal contacts clean.
On using your camcorder
On use and care
• Do not use or store the camcorder and
accessories in the following locations.
• Keep the Remote Commander and button-type
battery out of children’s reach. If the battery is
accidentally swallowed, consult a doctor
immediately.
• If the battery electrolytic liquid has leaked,
– Anywhere extremely hot or cold. Never leave
them exposed to temperatures above 60 °C
(140 °F), such as under direct sunlight, near
heaters or in a car parked in the sun. They
may malfunction or become deformed.
– consult your local authorized Sony service
facility.
– wash off any liquid that may have contacted
your skin.
– if any liquid gets in your eyes, wash with
plenty of water and consult a doctor.
– Near strong magnetic fields or mechanical
vibration. The camcorder may malfunction.
– Near strong radio waves or radiation. The
camcorder may not be able to record properly.
– Near AM receivers and video equipment.
Noise may occur.
x When not using your camcorder for a
long time
• Periodically turn on the camcorder and play a
cassette for about 3 minutes.
– On a sandy beach or anywhere dusty. If sand
or dust gets in your camcorder, it may
malfunction. Sometimes this malfunction
cannot be repaired.
– Near windows or outdoors, where the LCD
screen, the viewfinder, or the lens may be
exposed to direct sunlight. This damages the
inside of the viewfinder or the LCD screen.
– Anywhere very humid.
• Operate your camcorder on DC 6.8 V/7.2 V
(battery pack) or DC 8.4 V (AC Adaptor).
• For DC or AC operation, use the accessories
recommended in these operating instructions.
• Do not let your camcorder get wet, for example,
from rain or sea water. If your camcorder gets
wet, it may malfunction. Sometimes this
malfunction cannot be repaired.
• Use up the battery pack completely before
storing it.
Moisture condensation
If your camcorder is brought directly from a
cold place to a warm place, moisture may
condense inside your camcorder, on the
surface of the tape, or on the lens. In this
state, the tape may stick to the head drum
and be damaged or your camcorder may not
operate correctly. If there is moisture inside
your camcorder, [%Z Moisture
condensation. Eject the cassette] or [%
Moisture condensation. Turn off for 1H.]
appears. The indicator will not appear when
the moisture condenses on the lens.
• If any solid object or liquid gets inside the
casing, unplug your camcorder and have it
96
x If moisture condensation has occurred
None of the functions except cassette
ejection will work. Eject the cassette, turn
off your camcorder, and leave it for about
one hour with the cassette lid open. Your
camcorder can be used again when both of
the following conditions are met:
This occurs if the HDV signals cannot be
recorded or played back correctly because
of dirt on the tape or video head. Depending
on the cassette, this fairly infrequently
occurs even if the cassette is brand new or
is not used a lot.
If this freezing point is created while
playing back, you can solve this problem
and see the pictures by rewinding after
slightly forwarding. Such a freezing point
cannot be recovered if it was created while
recording.
To prevent such a problem, use the Sony
mini DV cassette. It is recommended you
use a cleaning cassette (optional) before
recording anything important.
• If the following problem occurs, clean the video
heads for 10 seconds with the Sony DVM-
12CLD cleaning cassette (optional).
• The warning message does not appear when the
power is turned on.
• Neither % or Z flash when a cassette is inserted
and video operation buttons are touched.
If moisture starts to condense, your
camcorder sometimes cannot detect
condensation. If this happens, the cassette is
sometimes not ejected for 10 seconds after
the cassette lid is opened. This is not a
malfunction. Do not close the cassette lid
until the cassette is ejected.
x Note on moisture condensation
Moisture may condense when you bring
your camcorder from a cold place into a
warm place (or vice versa) or when you use
your camcorder in a humid place as shown
below.
– Playback pictures do not move.
– Playback pictures do not appear.
– The sound breaks off.
– [x
Dirty video head. Use a cleaning
cassette.] appears on the screen during
recording.
• When you bring your camcorder from a ski
slope into a place warmed up by a heating
device.
– The following phenomenon occurs in HDV
format.
• When you bring your camcorder from an air
conditioned car or room into a hot place outside.
• When you use your camcorder after a squall or a
shower.
• When you use your camcorder in a hot and
humid place.
The playback The playback screen
screen pauses. goes blank.
(Solid blue screen)
x How to avoid moisture condensation
When you bring your camcorder from a
cold place into a warm place, put your
camcorder in a plastic bag and seal it
tightly. Remove the bag when the air
temperature inside the plastic bag has
reached the surrounding temperature (after
about one hour).
– The following phenomenon occurs in DV
format.
Block-noise appears.
Video head
If you play back a tape recorded in HDV
format, the image and sound may freeze for
a while (about 0.5 seconds).
Continued ,
97
Maintenance and precautions (Continued)
CALIBRATION
Touch the "x"
1/3
The playback screen goes blank.
(Solid blue screen)
CANCEL
• The video heads will degrade after long use. If
you cannot obtain a clear image even after using
3 Touch the “×” displayed on the screen with
the corner of the “Memory Stick Duo” or
the like.
a cleaning cassette (optional), it might be
because the video heads are worn out. Please
contact your Sony dealer or local authorized
Sony service facility to have the video heads
replaced.
The position of the “×” changes.
To cancel, touch [CANCEL].
LCD screen
• Do not exert excessive pressure on the LCD
screen, as it may cause damage.
If you did not press the right spot, start from
step 3 again.
• If your camcorder is used in a cold place, a
residual image may appear on the LCD screen.
This is not a malfunction.
• While using your camcorder, the back of the
LCD screen may heat up. This is not a
malfunction.
b Notes
• You cannot calibrate the LCD screen if it is
rotated.
On handling the casing
• If the casing is soiled, clean the camcorder body
with a soft cloth lightly moistened with water,
and then wipe the casing with a dry soft cloth.
• Avoid the following to avoid damage to the
finish.
– Using chemicals such as thinner, benzine,
alcohol, chemical cloths, repellent, insecticide
and sunscreen.
– Handling with above substances on your
hands.
x To clean the LCD screen
If fingerprints or dust make the LCD screen
dirty, it is recommended you use a soft
cloth to clean it. When you use the LCD
Cleaning Kit (optional), do not apply the
cleaning liquid directly to the LCD screen.
Use cleaning paper moistened with the
liquid.
x On adjustment of the touch panel
(CALIBRATION)
– Leaving the casing in contact with rubber or
vinyl objects for a long period of time.
The buttons on the touch panel may not
work correctly. If this happens, follow the
procedure below. It is recommended you
connect your camcorder to the wall outlet
(wall socket) using the supplied AC
Adaptor during the operation.
About care and storage of the lens
• Wipe the surface of the lens clean with a soft
cloth in the following instances:
– When there are fingerprints on the lens
surface.
– In hot or humid locations
1 Slide the POWER switch repeatedly to turn
on the PLAY/EDIT lamp.
– When the lens is exposed to salty air such as
at the seaside.
• Store in a well-ventilated location subject to
little dirt or dust.
• To prevent mold, periodically clean the lens as
described above. It is recommended that you
operate your camcorder about once a month to
keep it in optimum state for a long time.
2 Touch
t [MENU] t
(STANDARD SET) t [CALIBRATION]
t
.
98
Specifications
System
Video recording system (HDV)
2 rotary heads, Helical scanning system
Video recording system (DV)
On charging the pre-installed
rechargeable battery
Your camcorder has a pre-installed
rechargeable battery to retain the date, time,
and other settings even when the POWER
switch is set to OFF (CHG). The pre-
installed rechargeable battery is always
charged while your camcorder is connected
to the wall outlet (wall socket) via the AC
Adaptor or while the battery pack is
inserted. The rechargeable battery will be
fully discharged in about 3 months if
you do not use your camcorder at all
without the AC Adaptor connected or the
battery pack attached. Use your camcorder
after charging the pre-installed
2 rotary heads, Helical scanning system
Still image recording system
1
Exif Ver. 2.2*
Audio recording system (HDV)
Rotary heads, MPEG-1 Audio Layer -2,
Quantization: 16 bits (Fs 48 kHz,
stereo)
transfer rate: 384 kbps
Audio recording system (DV)
Rotary heads, PCM system
Quantization: 12 bits (Fs 32 kHz, stereo
1, stereo 2), 16 bits (Fs 48 kHz, stereo)
Video signal
NTSC color, EIA standards
1080/60i specification
Usable cassette
rechargeable battery.
However, even if the pre-installed
rechargeable battery is not charged, the
camcorder operation will not be affected as
long as you are not recording the date.
Mini DV cassette with the
printed
mark
x Procedures
Connect your camcorder to a wall outlet
(wall socket) using the supplied AC
Adaptor, and leave it with the POWER
switch set to OFF (CHG) for more than 24
hours.
Tape speed (HDV)
Approx. 18.81 mm/s
Tape speed (DV)
SP: Approx. 18.81 mm/s
LP: Approx. 12.56 mm/s
Recording/playback time (HDV)
60 min (using a DVM60 cassette)
Recording/playback time (DV)
SP: 60 min (using a DVM60 cassette)
LP: 90 min (using a DVM60 cassette)
Fast forward/rewind time
Approx. 2 min 40 s (using a DVM60
cassette and rechargeable battery pack)
Approx. 1 min 45 s (using a DVM60
cassette and AC Adaptor)
Viewfinder
Electric viewfinder (color)
Continued ,
99
Specifications (Continued)
2
* The unique pixel array of Sony’s
Image device
ClearVid CMOS sensor and image
processing system (new Enhanced
Imaging Processor) allows for still
image resolution equivalent to the sizes
described.
6.3 mm (1/2.9 type) CMOS sensor
Recording pixels (still, 4:3):
Max. 6.1 mega (2 848 × 2 136) pixels*
Gross: Approx. 3 200 000 pixels
Effective (movie, 16:9):
Approx. 2 280 000 pixels
Effective (movie, 4:3):
Approx. 1 710 000 pixels
Effective (still, 16:9):
2
Input/Output connectors
Audio/Video output
10-pin connector
Video signal: 1 Vp-p, 75 Ω(ohms)
Luminance signal: 1 Vp-p, 75 Ω(ohms)
Chrominance signal: 0.286 Vp-p, 75 Ω
(ohms)
Approx. 2 280 000 pixels
Effective (still, 4:3):
Approx. 3 040 000 pixels
Lens
Audio signal: 327 mV (at load
impedance 47 kΩ(kilohms)), Output
impedance with less than 2.2 kΩ
(kilohms)
Carl Zeiss Vario-Sonnar T
10 × (Optical), 20 × (Digital)
Focal length
f=5.4 ~ 54 mm (7/32 ~ 2 1/4 in.)
When converted to a 35 mm still
camera
COMPONENT OUT jack
Y: 1 Vp-p, 75 Ω(ohms)
PB/PR, CB/CR: 350 mV, 75 Ω(ohms)
HDMI OUT jack
TypeA (19-pin)
Headphone jack
In CAMERA-TAPE: 40 ~ 400 mm
(1 5/8 ~ 15 3/4 in.) (16:9), 49 ~ 490 mm
(1 15/16 ~ 19 3/8 in.) (4:3)
In CAMERA-MEMORY: 40 ~ 400 mm
(1 5/8 ~ 15 3/4 in.) (16:9), 37 ~ 370 mm
(1 1/2 ~ 14 5/8 in.) (4:3)
Stereo minijack (Ø 3.5 mm)
LANC jack
Stereo mini-minijack (Ø 2.5 mm)
USB jack
F1.8 ~ 2.9
Filter diameter: 37 mm (1 1/2 in.)
Color temperature
mini-B
MIC (PLUG IN POWER) jack
Stereo minijack (Ø 3.5 mm)
HDV/DV jack
[AUTO], [ONE PUSH], [INDOOR]
(3 200 K),
[OUTDOOR] (5 800 K)
i.LINK Interface (IEEE1394, 4-pin
connector S100)
Minimum illumination
5 lx (lux) ([AUTOSLW SHTR] [ON],
Shutter speed 1/30 sec)
0 lx (lux) (during NightShot function)
LCD screen
Picture
1
* “Exif” is a file format for still images,
6.7 cm (2.7 type, aspect ratio 16:9)
Total dot number
211 200 (960 × 220)
established by the JEITA (Japan
Electronics andInformationTechnology
Industries Association). Files in this
format can have additional information
such as your camcorder’s setting
information at the time of recording.
100
Operating temperature
0 °C to + 40 °C (32 °F to 104 °F)
Storage temperature
-20 °C to + 60 °C (-4 °F to + 140 °F)
Dimensions (approx.)
General
Power requirements
DC 6.8 V/7.2 V (battery pack)
DC 8.4 V (AC Adaptor)
Average power consumption
During camera recording using the
viewfinder with normal brightness:
HDV recording 4.2 W
48 × 29 × 81 mm (1 15/16 × 1 3/16 ×
3 1/4 in.) (w/h/d) excluding the
projecting parts
Mass (approx.)
DV recording 4.0 W
170 g (6.0 oz) excluding the power cord
(mains lead)
During camera recording using the
LCD with normal brightness:
HDV recording 4.5 W
* See the label on the AC Adaptor for other
specifications.
DV recording 4.3 W
Operating temperature
0 °C to + 40 °C (32 °F to 104 °F)
Storage temperature
-20 °C to + 60 °C (-4 °F to + 140 °F)
Dimensions (approx.)
Rechargeable battery pack (NP-FH60)
Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
82 × 82 × 138 mm
Capacity
(3 1/4 × 3 1/4 × 5 1/2 in.) (w/h/d)
including the projecting parts
82 × 82 × 138 mm
(3 1/4 × 3 1/4 × 5 1/2 in.) (w/h/d)
including the projecting parts with the
supplied battery pack NP-FH60
attached
7.2 Wh (1 000 mAh)
Dimensions (approx.)
31.8 × 33.3 × 45.0 mm
(1 5/16 × 1 5/16 × 1 13/16 in.) (w/h/d)
Mass (approx.)
80 g (2.9 oz)
Operating temperature
0 °C to + 40 °C (32 °F to 104 °F)
Type
Mass (approx.)
550 g (1 lb 3 oz) main unit only
650 g (1 lb 6 oz) including the NP-
FH60 rechargeable battery pack and
DVM60 cassette.
Lithium ion
Design and specifications are subject to change
without notice.
Supplied accessories
AC Adaptor AC-L200/L200B
Power requirements
AC 100 V - 240 V, 50/60 Hz
Current consumption
0.35 - 0.18 A
Power consumption
18 W
Output voltage
DC 8.4 V*
Continued ,
101
Specifications (Continued)
On trademarks
Notes on the License
• “Handycam” and
ANY USE OF THIS PRODUCT OTHER THAN
CONSUMER PERSONAL USE IN ANY
MANNER THAT COMPLIES WITH THE
MPEG-2 STANDARD FOR ENCODING
VIDEO INFORMATION FOR PACKAGED
MEDIA IS EXPRESSLY PROHIBITED
WITHOUT A LICENSE UNDER APPLICABLE
PATENTS IN THE MPEG-2 PATENT
PORTFOLIO, WHICH LICENSE IS
are
registered trademarks of Sony Corporation.
• HDV and the HDV logo are trademarks of Sony
Corporation and Victor Company of Japan, Ltd.
• “Memory Stick,” “
Duo,” “
PRO Duo,” “
“Memory Stick PRO-HG Duo,”
“
Micro,” “MagicGate,” “
,” “Memory Stick
,” “Memory Stick
,”
AVAILABLE FROM MPEG LA, L.L.C., 250
STEELE STREET, SUITE 300, DENVER,
COLORADO 80206.
,” “Memory Stick
,”
“MagicGate Memory Stick” and “MagicGate
Memory Stick Duo” are trademarks of Sony
Corporation.
• “InfoLITHIUM” is a trademark of Sony
Corporation.
• i.LINK and are trademarks of Sony
Corporation.
•
is a trademark.
• “x.v.Color” is a trademark of Sony Corporation.
• Microsoft, Windows, Windows Media,
Windows Vista, and DirectX are trademarks or
registered trademarks of U.S. Microsoft
Corporation in the U.S. and other countries.
• Macintosh and Mac OS are trademarks of Apple
Inc. in the U.S. and other countries.
• HDMI, the HDMI logo, and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
• Intel, Intel Core and Pentium are either
registered trademarks or trademarks of Intel
Corporation and its subsidiaries in the United
States and/or other countries.
• Adobe and Adobe Reader are either registered
trademarks or trademarks of Adobe Systems
Incorporated in the United States and/or other
countries.
All other product names mentioned herein may be
the trademarks or registered trademarks of their
respective companies. Furthermore, ™ and “®”
are not mentioned in each case in this manual.
102
QIduicek Rnetfeirefnyceing parts and controls
The numbers in ( ) are reference pages.
1
2
3
4
8
9
q;
qa
5
qs
qd
6
7
• The Active Interface Shoe has a safety
device for fixing the installed accessory
securely. To connect an accessory, press
down and push it to the end, and then
tighten the screw. To remove an accessory,
loosen the screw, and then press down and
pull out the accessory.
E Eyecup
• Connecting with an external device wears
out the battery pack faster.
• The available video signals are read, and the
appropriate output format is selected and
output automatically.
• You can check the setup value of HDMI
• When you are recording movies with an
external flash (optional) connected to the
accessory shoe, turn off the power of the
external flash to prevent charging noise
being recorded.
• You cannot use an external flash (optional)
and the built-in flash at the same time.
H Active Interface Shoe
The Active Interface Shoe supplies
power to optional accessories such as a
video light, a flash, or a microphone.
The accessory can be turned on or off as
you operate the POWER switch on your
camcorder. Refer to the operating
instructions supplied with your
accessory for details.
J CAMERA-TAPE, CAMERA-
MEMORY, PLAY/EDIT mode lamps
K
L
• When you connect an accessory, open the
shoe cover.
Continued ,
103
Identifying parts and controls (Continued)
7
8
9
1
2
3
4
0
qa
qs
5
6
LANC HDV/DV
COMPONENT OUT A/V OUT
qd qf qg qh qj
qk ql
N RESET button
Initializes all the settings, including the
setting of the date and time (Menu items
customized on Personal Menu are not
initialized).
O
P
LANC jack (blue)
The LANC control jack is used for
controlling the tape transport of video
devices and peripherals connected to it.
H
(USB) jack (71)
I Speaker
Playback sounds come out from the
S i (Headphone) jack (green)
speaker. For how to adjust the volume,
104
1
2
3
4
5
6
7
qs
8
9
q;
qa
qd
A
OPEN/EJECT lever (19)
B Flash
D Remote sensor/Infrared port
towards the remote sensor to operate
your camcorder.
M Tripod receptacle
Attach the tripod (optional: the length of
the screw must be less than 5.5 mm (7/
32 in.)) to the tripod receptacle using a
tripod screw.
E Microphone
An Active Interface Shoe compatible
microphone (optional) will take
precedence when connected.
Attaching the supplied lens hood
Place the lens hood against the lens hood
receptacle of the camcorder, and turn it in
the direction of the arrow.
F REC lamp (Camera recording lamp)
• The REC lamp lights up in red during
• The REC lamp flashes if the remaining tape
or battery power is low.
G MIC (PLUG IN POWER) jack
When an external microphone
(optional) is connected, it takes
precedence over the internal
microphone (p. 105).
H Hook for the Shoulder belt
Attach the Shoulder belt (optional).
Continued ,
105
Identifying parts and controls (Continued)
E Video control buttons (Rewind,
To remove the lens hood
Loosen the lens hood by turning it in the
opposite direction of the arrow in the
illustration above.
• Remove the lens hood when you use the flash,
Nightshot or SuperNightshot, or its shadow will
appear in the picture.
Playback, Fast-forward, Pause, Stop,
Slow) (28)
G Transmitter
Remote Commander
7
* These buttons are not available during Easy
Handycam operation.
b Notes
8
9
1
2
• Remove the insulation sheet before using the
Remote Commander.
• Aim the Remote Commander towards the
remote sensor to operate your camcorder
3
4
To change the battery of the Remote
Commander
1 While pressing on the tab, inset your
fingernail into the slit to pull out the battery
case.
5
6
q;
2 Place a new battery with the + side facing
up.
3 Insert the battery case back into the Remote
Commander until it clicks.
Insulation sheet
Tab
WARNING
Battery may explode if mistreated. Do not
recharge, disassemble or dispose of in fire.
The on-screen image when you press this
button will be recorded onto the “Memory
Stick Duo” as a still image.
B Memory control buttons (Index*, –/+,
b Notes
Memory playback) (29)
• When the lithium battery becomes weak, the
operating distance of the Remote Commander
may shorten, or the Remote Commander may
not function properly. In this case, replace the
battery with a Sony CR2025 lithium battery.
Use of another battery may present a risk of fire
or explosion.
D . > (Previous/Next) buttons*
(33)
106
Indicators displayed during recording/playback
A Recording format (
or
)
Recording movies
Recording mode (SP or LP) is also displayed
in the DV format.
2
3
4
5
qd
B Remaining battery (approx.)
1
C Recording status ([STBY] (standby) or
[REC] (recording))
D During recording:
Tape counter (hour: minute: second)
During playback:
GUIDE
6
7
8
9
Time code (hour: minute: second:
frame)
Recording still images
E Recording capacity of the tape (approx.)
2
0
qaqs
qf
F Review button for still images on the
“Memory Stick Duo” (24)
Appears when “Memory Stick Duo” is
inserted.
1111
FINE
6.1M
60min
101
G END SEARCH/Rec review display
6
8
9
Viewing movies
2
qg
4
5
8
1
N “Memory Stick Duo” indicator and the
number of images that can be recorded
(approx.)
z Tips
• The date/time during recording and the camera
setting data will be recorded automatically.
They do not appear on the screen during
recording, but you can check them as [DATA
qh
9
Viewing still images
2
qj qa
qk ql
O Tape transport indicator
Q Data file name
w;
6.1M
MEMORY PLAY
wa
8
wgwh
GUIDE
R Picture number/Total number of
recorded pictures in the current
playback folder
ws
wd
wf
9
Continued ,
107
Indicators displayed during recording/playback (Continued)
T Previous/Next folder icon
The following indicators appear when the first
or last picture of the current folder is
displayed and when there are multiple folders
on the same “Memory Stick Duo.”
Touch
folder.
to move to the previous
:
Touch
to move to the next folder.
:
:
Touch
/
to move to either
the previous or the next folder.
108
Center
Indicators when you made
changes
Indicator
Meaning
Color Slow Shutter (47)
Upper left
Upper right
PictBridge connecting
(71)
120
Q.REC
EZ
Warning (87)
NightShot (27)
+
3
+
2
Bottom
Center
Bottom
Upper left
Indicator
Meaning
Indicator
Meaning
AE SHIFT (45)
WB SHIFT (45)
SP LP
9
Interval photo recording
(52)
SCENE SELECT (42)
Flash light/
REDEYE REDUC (46)
Backlight (27)
.
Upper right
n
White balance (43)
SteadyShot off (48)
Zebra (47)
Indicator
Meaning
HDV input/
DV input (67)
Tele macro (46)
CONV.LENS (49)
HDV output/
i.LINK connection
Slide show (52)
LCD backlight off (18)
* The settings can be made only for the pictures
in the DV format.
Continued ,
109
Indicators displayed during recording/playback (Continued)
**The setting can be made only for the pictures in
the HDV format.
Other indicator
Indicator
Meaning
b Notes
• Indicators and their positions are approximate
and differ from what you actually see.
Checking the screen indicators
(Display guide)
You can easily check the meaning of each
indicator that appears on the LCD screen.
1 Touch [GUIDE] t [DISP GUIDE].
60min
STBY
GUIDE
P-MENU
2 Touch the area including the indicator
that you want to check.
The meanings of the indicators in the
area are listed on the screen. If you
cannot find the indicator you want to
check, touch
/
to toggle.
To finish the operation, touch [END].
b Notes
• Some screen displays cannot be checked with
[DISP GUIDE].
z Tips
• You can also operate by touching
[DISP GUIDE].
t
110
Index (Continued)
M
Maintenance and precautions
Q
QUICK REC
R
REC CTRL
N
REC FOLDER (Recording
REC MODE
NS LIGHT
SUNRSE SUNSET
SUPER NS
Number of recordable pictures
T
O
REMOTE CTRL
P
S
PB FOLDER
SD (standard definition) image
U
Searching for the starting point
PICT.APPLI. menu
PICT.EFFECT
112
V
VAR.SPD PB
VF B.LIGHT
W
WB SHIFT
X
Z
113
114
Spanish Quick Guide/Guía rápida en español
Paso 1: Comprobación de los elementos
suministrados
Cable USB (1)
Asegúrese de que su videocámara contiene
los siguientes elementos.
El número entre paréntesis indica la
cantidad del elemento.
Adaptador de alimentación de ca (1)
Batería recargable NP-FH60 (1)
Cable de alimentación (1)
Protector del objetivo (1)
Control remoto inalámbrico (1)
Extraiga el protector del objetivo si utiliza el
flash, Nightshot o SuperNightshot, o
cuando aparece su sombra en la imagen.
Tiene instalada una pila de litio tipo botón.
CD-ROM “Handycam Application
Software” (1)
Cable de conexión de A/V (1)
Guía de operaciones (este manual) (1)
Cable de video componente (1)
Cable i.LINK (1)
115
Paso 2: Carga de la batería
2
Interruptor
POWER
1
Toma DC IN
3
4
Batería
Indicador
CHG (carga)
/
Clavija de cc
4
Al tomacorriente
de la pared
Adaptador de alimentación de ca
Cable de alimentación
Para cargar la batería “InfoLITHIUM”
(serie H), conéctela a la
videocámara.
4
Conecte el cable de alimentación
al adaptador de alimentación de
ca y al tomacorriente de pared.
b Notas
El indicador /CHG (carga) se
enciende y se inicia el proceso de carga.
El indicador /CHG (carga) se apaga
cuando la batería está completamente
cargada.
• No puede conectar ninguna batería
“InfoLITHIUM” que no sea de la serie H a la
videocámara.
1
Instale la batería en la
videocámara.
b Notas
Deslice la batería en el sentido de la
flecha hasta que calce para colocarla.
• Desconecte el adaptador de alimentación de ca
de la toma DC IN sujetando a la vez la
videocámara y la clavija de cc.
2
3
Deslice el interruptor POWER
hasta la posición OFF (CHG)
(el ajuste predeterminado).
z Sugerencias
• Puede utilizar su videocámara conectada a una
fuente de alimentación como un tomacorriente
de pared tal como se muestra en la ilustración.
La batería no perderá la carga en este caso.
Conecte el adaptador de
alimentación de ca a la toma DC
IN de la videocámara. Asegúrese
de que la marca v de la clavija de
cc esté orientada hacia a la marca
v de la videocámara.
116
Para retirar la batería
Carga restante de la batería (aprox.)
Deslice el interruptor POWER hasta la
posición OFF (CHG). Deslice la palanca
BATT (liberación de la batería) y retire la
batería.
NIVEL CARGA BATERÍA
TIEMPO GRAB DISPON
PANT.LCD
VISOR
60
65
Capacidad de grabación (aprox.)
Puede comprobar la carga restante de la
batería en la pantalla LCD.
Indicador
Estado
Suficiente energía restante
Palanca BATT
(liberación de la
batería)
Batería baja, la grabación/
reproducción se detendrá
pronto.
Sustituya la batería por una
completamente cargada, o
cargue la batería.
Cuando guarde la batería
Descargue completamente la batería antes
de guardarla durante un período
prolongado.
Tiempo de carga
Tiempo aproximado (min) necesario para
cargar totalmente una batería descargada
por completo.
Para comprobar la carga restante de
la batería (Información sobre la
batería)
Ajuste el interruptor POWER en
OFF(CHG) y, a continuación, presione
DISPLAY/BATT INFO.
Tiempo de
Batería
carga
NP-FH50
135
NP-FH60
(suministrada)
135
NP-FH70
170
390
NP-FH100
DISPLAY/
BATT INFO
Después de cierto tiempo, el tiempo
disponible para grabación y la información
sobre la batería aparecen durante
aproximadamente 7 s (segundo). Puede ver
la información sobre la batería durante
20 s (segundo) presionando nuevamente
DISPLAY/BATT INFO mientras se
visualiza la información.
Continued ,
117
Paso 2: Carga de la batería (Continuación)
Tiempo de grabación
Tiempo aproximado (min) disponible
cuando utiliza una batería completamente
cargada.
Panel LCD Panel LCD
abierto* cerrado
Batería
Formato
grabado
HDV DV HDV DV
105 115 120 130
140 150 160 170
NP-FH50
Tiempo de Tiempo de
grabación
continua
NP-FH60
(suministrada)
Batería
grabación
normal*
NP-FH70
230 245 255 280
525 565 590 635
Formato de
grabación
HDV DV HDV DV
NP-FH100
NP-FH50
70
70
75
90
70 40
75 40
80 40
95 50
40
40
45
50
55
55
85
90
90
* Con la luz de fondo de la pantalla LCD
encendida.
Acerca de la batería
• Antes de cambiar la batería, deslice el
interruptor POWER a la posición OFF (CHG).
• El indicador /CHG (carga) parpadeará durante
la carga o la información de la batería no se
mostrará correctamente en las siguientes
condiciones.
– La batería no está correctamente conectada.
– La batería está dañada.
NP-FH60
(suministrada)
95 100 50
100 105 55
150 155 80
155 165 85
160 170 85
NP-FH70
NP-FH100
345 365 185 195
365 385 195 210
375 395 205 215
– La batería está agotada (sólo para la
información de la batería).
• Cuando el adaptador de alimentación de ca esté
conectado a la toma DC IN de la videocámara,
la batería no suministrará alimentación, aunque
el cable de alimentación esté desconectado del
tomacorriente de pared.
• Si instala una luz de video opcional, es
recomendable que utilice los modelos de batería
NP-FH70 o NP-FH100.
* El tiempo de grabación normal muestra la hora
cuando se repite la operación de inicio/
detención de la grabación, al conectar y
desconectar la alimentación y al usar la función
de zoom.
b Notas
• Todo los tiempos se calcularon en las siguientes
condiciones:
Superior: Con la luz de fondo de la pantalla
LCD encendida.
Medio: Con la luz de fondo de la pantalla LCD
apagada.
Acerca del tiempo de carga/grabación/
reproducción
• Tiempos medidos con la videocámara a una
temperatura de 25 ºC
(se recomienda una temperatura de 10 a 30 ºC).
Inferior: Grabación con el visor mientras el
panel LCD se encuentra cerrado.
• El tiempo de grabación y de reproducción será
más corto cuando use la videocámara a bajas
temperaturas.
Tiempo de reproducción
Tiempo aproximado (min) disponible
cuando utiliza una batería completamente
cargada.
• El tiempo de grabación y de reproducción será
más corto en función de las condiciones de uso
de la videocámara.
118
Paso 3: Encendido y
ajuste de la fecha y la
hora
Ajuste la fecha y la hora cuando use la
videocámara por primera vez. De lo
contrario, la pantalla [AJUS.RELOJ]
aparecerá cada vez que encienda la
videocámara o cambie la posición del
interruptor POWER.
Acerca del adaptador de alimentación de
ca
• Si utiliza el adaptador de alimentación de ca
conéctelo a un tomacorriente de pared cercano.
Si se produce alguna falla de funcionamiento al
utilizar la videocámara, desconecte el adaptador
de alimentación de ca del tomacorriente de
inmediato.
• No utilice el adaptador de alimentación de ca
colocado en un espacio angosto, tal como entre
una pared y los muebles.
• Evite la formación de cortocircuitos en la clavija
de cc del adaptador de alimentación de ca o en
el terminal de la batería con objetos metálicos.
Podría provocar una falla de funcionamiento.
• Aunque la videocámara esté apagada, seguirá
recibiendo adaptador de alimentación de ca
(corriente doméstica) mientras esté conectada a
la toma de pared mediante el adaptador de
alimentación de ca
Interruptor POWER
Toque los botones
de la pantalla LCD.
1
Mientras presiona el botón verde,
deslice el interruptor POWER en
el sentido de la flecha para que se
encienda el indicador
correspondiente.
CAMERA-TAPE: para grabar en una
cinta.
CAMERA-MEMORY: para grabar en
un “Memory Stick Duo”.
PLAY/EDIT: para reproducir o editar
imágenes.
Aparecerá la pantalla [AJUS.RELOJ].
ESPERA –:––:––
AJUS.RELOJ
A
2008
M
1
D
1 12:00AM
OK
Continued ,
119
Paso 3: Encendido y ajuste de la fecha y la hora (Continuación)
b Notas
2
Ajuste [A] (año) con
/
.
• Si no usa la videocámara durante
aproximadamente 3 meses, la batería
recargable incorporada se descarga y es posible
que los ajustes de la fecha y la hora se borren de
la memoria. En este caso, cargue la batería
recargable y ajuste la fecha y la hora
nuevamente.
• Al momento de la compra, la alimentación se
ajusta para desconectarse automáticamente si no
se opera la videocámara durante unos
5 min (minuto) para ahorrar energía de la batería
([APAGADO AUTO]).
Puede seleccionar cualquier año hasta el
año 2079.
3
4
Vaya hasta [M] (mes) con
ajústelo con
, y
/
.
Vaya hasta [D] (día) con
,
ajústelo con y repita la
/
z Sugerencias
operación para ajustar las horas y
los minutos.
• La fecha y hora no aparecen durante la
grabación, pero se graban automáticamente en
la cinta y pueden visualizarse durante la
reproducción ([CÓDIGO DATOS] (durante el
funcionamiento de Easy Handycam, sólo puede
ajustar [FECHA/HORA])).
Ajuste la medianoche a las 12:00 AM.
Ajuste el mediodía a las 12:00 PM.
• La tapa del objetivo se abre automáticamente al
ajustar el interruptor POWER en CAMERA-
TAPE o CAMERA-MEMORY.
5
Asegúrese de que los ajustes de
fecha y hora son correctos y, a
continuación, toque
.
• Si los botones del panel sensible al tacto no
funcionan correctamente, ajuste el panel
sensible al tacto (CALIBRACIÓN).
El reloj se pone en funcionamiento.
Cambio del ajuste de idioma
Para apagar la videocámara
Deslice el interruptor POWER hasta la
posición OFF (CHG).
Puede cambiar las indicaciones en pantalla
para que muestren mensajes en un idioma
en particular.
Toque
t [MENU] t
Para restablecer la fecha y la hora
Para ajustar la fecha y la hora deseadas,
(HORA/LANGU.) t [LANGUAGE], y
luego seleccione el idioma deseado.
toque
[AJUS.RELOJ].
t
/
t
120
Paso 4: Ajustes antes de grabar
Panel LCD
Visor
Abra el panel LCD 90 grados con respecto
a la videocámara (1) y luego gírelo hacia
el mejor ángulo para grabar o
Puede ver imágenes utilizando el visor para
evitar el desgaste de la batería o cuando la
imagen en la pantalla LCD sea deficiente.
reproducir (2).
Visor
DISPLAY/BATT INFO
180 grados
(máx.)
2
1
2
90 grados con respecto
90 grados
Palanca de ajuste
del objetivo del visor
Muévala hasta que la
imagen aparezca nítida.
a la videocámara
(máx.)
Para desactivar la luz de fondo de la
pantalla LCD y prolongar la duración
de la batería
Mantenga presionado DISPLAY/BATT
INFO durante unos s (segundo) hasta que
z Sugerencias
• Puede ajustar el brillo de fondo del visor
seleccionando [AJ LCD/VISOR] - [LUZ
F.VISOR].
aparezca
.
Correa de sujeción
Este ajuste es práctico cuando utiliza la
videocámara en lugares muy luminosos o
cuando desea ahorrar energía. Este ajuste
no afectará a la imagen grabada. Para
encender la luz de fondo de la pantalla
LCD, mantenga presionado DISPLAY/
BATT INFO durante unos s (segundo)
Ajuste la correa de sujeción y sostenga la
cámara correctamente.
hasta que
desaparezca.
b Notas
• No presione los botones del panel LCD por
error al abrirlo o ajustarlo.
z Sugerencias
• Si gira el panel LCD 180 grados hacia el lado
del objetivo, podrá cerrarlo con la pantalla LCD
hacia afuera. Esto resulta conveniente para las
operaciones de reproducción.
• Consulte [AJ LCD/VISOR] - [BRILLO LCD]
para ajustar el brillo de la pantalla LCD.
• Presione DISPLAY/BATT INFO para activar o
desactivar los indicadores de pantalla (como la
información sobre la batería).
121
Paso 5: Inserción de una cinta o un “Memory
Stick Duo”
Cinta de videocasete
3
Cierre la tapa.
Solamente puede utilizar videocasetes mini
DV
.
Para expulsar el videocasete
Abra la tapa realizando el mismo
procedimiento que se describe en el paso 1
y extraiga el videocasete.
b Notas
• El tiempo disponible para grabación varía en
función del [ MODO GRAB.].
b Notas
1
Deslice y sostenga la palanca
OPEN/EJECT en el sentido de
la flecha y abra la tapa.
• No fuerce el compartimiento del
videocasete presionando la parte con la
marca {DO NOT PUSH} mientras se desliza
hacia adentro. Podría provocar una falla
de funcionamiento.
Palanca OPEN/EJECT
“Memory Stick Duo”
Puede utilizar “Memory Stick” que
presenten el logotipo que aparece a
continuación.
–
–
(“Memory Stick Duo”)
(“Memory Stick
Tapa
El compartimiento del videocasete sale
automáticamente y se abre.
PRO Duo”)
–
(“Memory Stick
PRO-HG Duo”)
z Sugerencias
2
Inserte un videocasete con la
cara de la ventanilla hacia afuera
y, a continuación, presione
• El número y la duración de las imágenes que se
pueden grabar varía en función de la calidad o
del tamaño de la imagen.
.
Presione ligeramente el centro de la parte
posterior del videocasete.
Ventanilla
1
2
Abra el panel LCD.
Compartimiento
del videocasete
Inserte el “Memory Stick Duo” en
la ranura para Memory Stick Duo
en el sentido correcto hasta que
calce.
El compartimiento del
videocasete se desliza
automáticamente hacia adentro.
122
Indicador de acceso
Para expulsar un “Memory Stick Duo”
Empuje suavemente el “Memory Stick
Duo” hacia dentro una vez.
b Notas
• Cuando el indicador de acceso se enciende o
parpadea, la videocámara está leyendo o
grabando datos. No sacuda ni golpee la
videocámara, no la apague, ni extraiga el
“Memory Stick Duo” ni retire la batería. De lo
contrario, se podrían dañar los datos de
imágenes.
• Si fuerza el “Memory Stick Duo” en la ranura
en la dirección incorrecta, puede dañarse el
“Memory Stick Duo”, la ranura para el Memory
Stick Duo o los datos de imágenes.
• Al insertar o expulsar el “Memory Stick Duo”,
procure que el “Memory Stick Duo” no salte y
se caiga.
123
Grabación
Cubierta del objetivo
Se abre según el ajuste del
interruptor POWER.
PHOTO
Interruptor POWER
START/STOP B
START/STOP A
Grabación de películas
Las películas se graban en una cinta.
Deslice el interruptor POWER varias veces en el sentido de la
flecha para que se encienda el indicador CAMERA-TAPE.
Si el interruptor POWER está ajustado en la
posición OFF (CHG), deslícelo mientras presiona el
botón verde.
Presione START/STOP A (o B).
60min
60min
60min
60min
P-MENU
P-MENU
GUÍA
GUÍA
[GRAB.]
[ESPERA]
Para detener la grabación, presione START/STOP A (o B) nuevamente.
z Sugerencias
• Las imágenes se graban en formato HDV con el ajuste predeterminado.
124
Grabación de imágenes fijas
Las imágenes fijas se graban en el “Memory Stick Duo”.
Deslice el interruptor POWER varias veces en el sentido de la
flecha para que se encienda el indicador CAMERA-MEMORY.
Si el interruptor POWER está ajustado en la posición
OFF (CHG), deslícelo mientras presiona el botón
verde.
Mantenga presionado ligeramente PHOTO para ajustar el
enfoque y luego presiónelo completamente para grabar.
min
min
6,1M
6,1M
Pitido
Clic del obturador
P-MENU
P-MENU
GUÍA
GUÍA
Parpadeo b Encendido
Se escucha el sonido del obturador. Cuando
grabado.
desaparezca, la imagen se habrá
Para verificar la última grabación en un “Memory Stick Duo”
Toque
. Para borrar la imagen, toque
t [SÍ].
125
Reproducción
Deslice el interruptor POWER en el sentido de la flecha varias veces
para encender el indicador PLAY/EDIT.
Si el interruptor POWER está ajustado en la posición
OFF (CHG), deslícelo mientras presiona el botón
verde.
Reproducción de películas
Toque
para rebobinar hasta la escena deseada y luego toque
para iniciar la reproducción.
Alterna entre Reproducir o Pausa cada vez que lo toca*
60min
60min
GUÍA
P-MENU
Rebobinar/Avanzar rápidamente
Detener**
* La reproducción se detiene automáticamente si la pausa permanece accionada durante más de
3 min (minuto).
** Se visualiza
en lugar de
cuando se inserta un “Memory Stick Duo” con imágenes
grabadas y no se está reproduciendo una cinta.
Para ajustar el volumen del sonido
Gire el selector CAM CTRL para ajustar el volumen manualmente.
z Sugerencias
• También puede ajustar el volumen desde el menú.
Para buscar una escena durante la reproducción
Mantenga presionado
/
durante la reproducción (Búsqueda de imágenes), o
/
durante el avance rápido o rebobinado de la cinta (Exploración con salto).
z Sugerencias
• Puede reproducir en diversos modos ([
REP VL VAR]).
126
Visualización de imágenes fijas
Toque
.
Se visualiza la imagen grabada más recientemente.
60min
10/10
6,1M
REPR.MEM.
GUÍA
Cambia entre
los medios de
reproducción*
P-MENU
Anterior/Siguiente
Vaya a la visualización de
la pantalla de índice
*
aparece en la pantalla de reproducción de cintas.
Para visualizar imágenes de un “Memory Stick Duo” en la pantalla de índice
Toque
. Toque una de las imágenes para regresar al modo de presentación sencilla.
FIN
B
A
A 6 imágenes anteriores o siguientes
B Imagen mostrada antes de cambiar a la pantalla de índice
Para ver imágenes de otras carpetas, toque
carpeta con y luego toque
t
t [REPR. CARP.], seleccione una
/
.
127
Additional information on this product and answers
to frequently asked questions can be found at our
Customer Support Website.
http://www.sony.net/
Printed in Japan
|