4 CHANNEL DVR
User Manual
SRD-470/470D
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN11 11
2010-04-30 오후 6:06:2233
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit.
Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. if the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from
tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
English _3
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN33 33
2010-04-30 오후 6:06:3399
overview
BEFORE START
This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection
to other equipment, menu setup, etc.
You have to keep in mind the following notices :
•
•
•
SAMSUNG retains the copyright on this manual.
This manual cannot be copied without SAMSUNG’s prior written approval.
We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of
instructions mentioned in this manual.
•
•
Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be
removed from the unit.
Before installing an additional HDD or connecting an external storage device (USB memory or USB HDD) to this
DVR, check the compatibility. Consult your provider for the compatibility list.
Warning
❖ Battery
It is essential that when changing the battery in the unit, the replacement battery must be of the same type
otherwise there may be a possibility of an explosion.
The following are the specifications of the battery you are using now.
•
•
•
•
Normal voltage : 3V
CALIFORNIA USA ONLY
Normal capacity : 170mAh
Continuous standard load : 0.2mA
This Perchlorate warning applies only to primary CR (Manganese Dioxide)
Lithium coin cells in the product sold or distributed ONLY in California USA.
“Perchlorate Material - special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.”
Operating temperature : -20°C ~ +85°C
(-4°F ~ +185°F)
Connect the power cord into a grounded outlet.
J
The Mains plug is used as a disconnect device and shall stay readily operable at any time.
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
❖ System Shutdown
Turning off the power while the product is in operation, or undertaking improper actions may cause damage
or malfunction to the hard drive or the product.
Please turn off the power using the Power button on the front of your DVR.
After selecting <OK> in the pop-up menu, you can pull off the power cord.
You may want to install a UPS system for safe operation in order to prevent damage caused by an
unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)
❖ Operating Temperature
The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).
This product may not work properly if you run right after a long period of storage at a temperature below the
guaranteed one.
Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand
at room temperature for a period.
Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F).
Likewise, the hard drive may not work at a temperature below the guaranteed one.
❖ Ethernet Port
This equipment is in door use and all the communication wirings are limited to inside of the building.
4_ overview
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN44 44
2010-04-30 오후 6:06:4400
CONTENTS
4
7
9
Before Start
OVERV4IEW
Features
Part Names and Functions (Rear)
10 Part Names and Functions (Front)
12 Remote Control
13 Checking the installation environment
INSTALLATION
14 HDD Addition
13
17 Connecting the Video, Audio, and Monitor
17 Connecting the USB
CONNECTING WITH OTHER1DEV7ICE
17 Connecting POS Device
18 Connecting the Alarm Input/Output
18 Connecting the RS485 Device
19 Connecting the Network
21 Getting Started
23 Live Screen Configuration
27 Live Mode
2L1IVE
29 Spot Out
29 Zoom
30 Audio ON/OFF
30 Freeze
30 Event Monitoring
32 System Setup
USING THE DVR
42 Setting the Device
50 Setting the Recording
53 Setting the Event
56 Backup
32
57 Network Configuration
64 Controlling a PTZ device
English _5
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN55 55
2010-04-30 오후 6:06:4400
overview
66 Search
SEARCH & PLAY
69 Playback
66
70 Introducing Web Viewer
71 Connecting Web Viewer
73 Using Live Viewer
79 Using Search Viewer
83 Viewer Setup
WEB7VIEW0ER
93 About
94 SEC Backup Viewer
BACKUP9VIEW4ER
96 Product Specification
99 Product Overview
100 Default Setting
APPENDIX
103 Troubleshooting
96
6_ overview
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN66 66
2010-04-30 오후 6:06:4411
FEATURES
The SRD DVR (Digital Video Recorder) employs H.264 video encoding for 4 channel inputs and G.723 audio
encoding for 4 channels while simultaneously supports hard disc recording and playback.
These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video
and audio data.
•
•
•
•
•
•
•
•
•
•
4 CH Composite Input Connectors
CIF(S)/2CIF(M)/4CIF(L) Recording
Network transfer regardless of the recording conditions using network specific codec
Improved quality using de-interlace chip
HDD information and status with HDD SMART
Record at 4CIF Size (NTSC: 704*480, PAL: 704*576) 120(NTSC)/100(PAL)IPS
4 CH Loop Through video port
HDD Overwrite
Massive HDD backup via USB 2.0
Backup using USB 2.0 memory and/or external CD/DVD writer
(DVD writer not supported in SRD-470)
•
•
•
•
•
•
Record and play 4 CH video data simultaneously
Various search modes (time, event, backup, POS, motion detection)
Lots of storage modes (time lapse, event, timed recording)
HDD extension (USB 2.0)
Alarm connection (input: 4, output:2, reset: 1)
Remote monitoring via Windows Network Viewer
English _7
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN77 77
2010-04-30 오후 6:06:4411
overview
Standards Approvals
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
M
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Package Contents
Please unwrap the product, and place the product on a flat place or in the place to be installed.
Please check the following contents are included in addition to the main unit.
Remote Control
Adaptor
Power Cable
Network Viewer Software /
User Manual CD
User Manual
Remote Control Battery (AAA)
HDD Fixing Screw
SATA Cable
(Only applicable for SRD-470 : 4EA)
(Only applicable for SRD-470 : 1EA)
For models that are not equipped with the HDD, one SATA cable is provided for HDD installation.
M
8_ overview
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN88 88
2010-04-30 오후 6:06:4422
PART NAMES AND FUNCTIONS (REAR)
1
2
3
4
5
11
10
9
8
7
6
Part Names
Functions
VGA
Output port for VGA video signal.
RS-232C communications port.
RS-232C
VIDEO OUT
BNC type of output port for the composite video signal.
Output port (RCA jack) for the audio signal.
AUDIO OUT
It is recommended to use an amplifier-integrated speaker for the output of the audio
signal.
AUDIO IN 1~4
NETWORK
Output ports (RCA jacks) for the audio signal.
Network connection port.
DC 12V
Port to be connected to the 12V power source.
1~4, G : Alarm input ports.
ALARM IN
ALARM OUT
RS485
1, 2, COM : Alarm output ports.
Used to establish RS485 communications. (TX+, TX-)
USB connection port.
USB
SPOT
BNC type of output port for the Spot signal.
Port to transfer the video signal to other video devices.
THROUGH
Input port for the composite video signal.
VIDEO IN
Supports both NTSC and PAL video signal.
English _9
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN99 99
2010-04-30 오후 6:06:4444
overview
PART NAMES AND FUNCTIONS (FRONT)
SRD-470
1
2
3
5
SRD-470
9
8
7
3
6
SRD-470D
1
2
4
5
SRD-470D
9
8
7
6
10_ overview
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1100 1100
2010-04-30 오후 6:06:4455
Part Names
Power
Functions
Power LED : Displays the power ON/OFF status.
Power Button : Used to turn the DVR ON/OFF.
In Live mode, pressing it will switch the mode to 4-split, PIP, and Auto Sequence in sequence.
In Search mode, pressing it will switch the mode to 9-split and 4-split in sequence.
For the Play Screen mode, refer to “Play”. (page 69)
MODE
AUDIO
ALARM
REC
Sets Audio ON/OFF.
Cancels the ALARM LED and the audible alarm when the alarm is going off, and to remove the
icon.
Starts or ends the recording.
Step Rewind () : Used for backward frame-by-frame search while in PAUSE.
Fast Rewind () : Used for quick backward search while in Play.
(-x2, -x4, -x8, -x16, -x32, -x64)
/
Stop : Used to stop the playback.
Play/Pause : Used to pause or resume the screen.
►/
/
Open/Close
Fast Forward () : Used for quick forward playback. (x2, x4, x8, x16, x32, x64)
Step Forward ( ) : Used for forward frame-by-frame search while in PAUSE.
Used to open and close the DVR-RW disc tray. (available for SRD-470D only)
ALARM : Lights on when an event occurs.
HDD : Displays the normal access to HDD.
Upon access to HDD, LED repeats on and off.
LED Indicator
NETWORK : Displays both network connection and data transfer status.
BACKUP : Displays when Backup is in progress.
REC : Lights on when recording is in progress.
Direction &
Used to change a value or move the cursor up/down/left/right (ꢀꢁ◄ ►).
Select Button
Selects a menu item or executes the selected menu.
PTZ : Sets PTZ Mode ON/OFF.
ZOOM(TELE) : Sets the screen to the x2 digital zoom.
Runs the TELE function in the PTZ Mode.
FREEZE(WIDE) : Runs the FREEZE function in the Live Mode.
Camera Control
Runs the WIDE function in the PTZ Mode.
SEARCH(VIEW) : This is the function that switches over to the Search mode.
(Perform the VIEW function when selecting the PTZ button.)
MENU : Used to access the Menu screen or move to the previous menu.
Used to select channel numbers directly in the Live Mode, or numbers in the numeric input
Channel
USB Port
mode.
Connects the USB devices.
English _11
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1111 1111
2010-04-30 오후 6:06:4466
overview
REMOTE CONTROL
BACKUP
SEARCH
Displays the search menu.
Displays the Backup Menu.
OPEN/CLOSE
Opens or closes the CD tray.
MODE
Changes the screen mode.
DVR
Activates the DVR function.
POWER
Displays the Exit pop up screen.
+
NUMBER [0~ 10]
Used as the numeric input keys, or displays a single
channel.
ID
Sets the ID of the system.
Select 2 digits from 0 ~ 9 while pressing the ID Key.
Skip Backward (by unit time),
Slow Rewind, Slow Forward,
Skip Forward (by unit time)
Move Frame
While paused, moves to the previous/next frame.
FR, STOP, PLAY/PAUSE, FF
T/W
PTZ
Zooms in or out.
Displays or ends PTZ.
SCROLL ,.
Moves the menu scroll.
MENU
RETURN
Goes to the system menu screen.
Returns to the previous screen.
Up/Down/Left/Right(▲▼◄ ►)/ENTER
Moves the cursor up/down/left/right, and runs the
Select Menu.
AUDIO
Turns Audio on/off.
FREEZE
ALARM
Freezes the screen temporarily.
Cancels the Alarm.
ZOOM
Runs the digital zoom (x2) function.
REC LOCK
REC
Selects the recording lock function.
Starts or ends the live recording.
PRESET
VIEW
Displays the Preset Setup.
Runs the View function in the PTZ mode.
Using the Numeric buttons
1. Press any button among 1 to 4.
2. Move to the selected channel number.
Changing the Remote Control ID
1. Press the ID button of the remote control and check the ID displayed on the DVR screen.
The factory default ID of the remote control is 00.
2. Enter 2 digits of your selection in order, while pressing the system [ID] button.
3. When ID input is done, press the system [ID] button again to check the setting.
If you want to change the remote control ID to 08: Press 0 and 8 in order while the system [ID] button is pressed.
M
Remote control's ID and DVR’s ID should be matched for proper operation. Refer to “Remote Devices”. (Page 46)
12_ overview
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1122 1122
2010-04-30 오후 6:06:4466
installation
Please take note of the followings before using this product.
•
•
•
•
•
•
•
•
Do not use the product outdoor.
Do not spill water or liquid in the connection part of the product.
Do not impose the system to excessive shock or force.
Do not pull out the power plug forcefully.
Do not disassemble the product on your own.
Do not exceed the rated input/output range.
Use a certified power cord only.
For the product with an input ground, use a grounded power plug.
CHECKING THE INSTALLATION ENVIRONMENT
Temperature
One Year: 24HR X 365 DAY =8,760 HR
Samsung Digital Video Recorder (“DVR” hereinafter) is a
Unit: ºC
state-of-art security device, and contains mass storage hard
disk(s) and critical circuits inside.
When the temperature rises inside the product, the product
may breakdown and the product life be shortened. Please
pay attention to the following recommendations before
installation.
Life (Unit: HOURS)
[Figure 1]
The followings are the recommendations when Samsung DVR is installed on a rack.
1. Please ensure that the rack inside is not sealed.
2. Please ensure the air is circulated through the inlet/outlet as shown in the picture.
3. If the DVR or other devices on a rack is to be stacked as in the picture, provide a
suitable space or install a ventilating opening for air circulation.
DI
DI
DI
DI
GI
T
A
L
V
ID
ID
ID
ID
EO
EO
EO
EO
RE
CO
RD
RD
RD
RD
ER
ER
ER
ER
SR
D-
47
0D
0D
0D
0D
MO
DE
AU
DIO
ALA
AL
RM
RM
RM
RM
AR
1
1
1
1
M
HDD
NET
NET
NET
NET
WO
WO
WO
WO
RK
RK
RK
RK
2
RE
BAC
BAC
BAC
BAC
KUP
KUP
KUP
KUP
REC
REC
REC
REC
3
4
ZO
OM
FR
EE
ZE
SE
AR
CH
TE
L
ME
ME
ME
ME
WID
NU
E
VIE
W
GI
GI
GI
T
A
L
V
RE
CO
SR
D-
47
4. For natural air convection, place the inlet at the bottom of the rack and the outlet on
top.
MO
DE
AU
DIO
ALA
ALA
RM
H
DD
2
RE
C
3
4
ZO
OM
FR
EE
ZE
SE
AR
CH
TE
LE
WD
NU
E
VIEW
T
A
L
V
RE
CO
SR
D-
47
MO
DE
AU
DIO
ALA
AL
AR
M
HDD
2
RE
3
5. It is strongly recommended that a fan motor is installed at the inlet and the outlet for air
circulation. (Please fit a filter at the inlet to screen dust or foreign substances.)
4
ZO
OM
FR
EEZ
E
SE
AR
TE
CH
L
WID
NU
E
VIE
W
T
A
L
V
RE
CO
SR
D-
47
MO
DE
AU
DIO
ALA
AL
AR
M
HDD
2
RE
C
3
4
ZO
OM
FRE
EZ
E
SE
AR
CH
TE
LE
WD
NU
E
6. Please maintain the temperature inside the rack or surrounding areas between 0°C ~
40°C (32°F ~ 104°F) as shown in the figure 1.
VI
EW
Rack Mount Instructions - The following or similar rack-mount instructions are
included with the installation instructions :
M
O
D
E
A
U
D
IO
A
LA
A
R
L
M
A
R
M
H
D
D
N
E
TW
O
R
K
2
R
BA
E
C
C
K
U
P
R
E
C
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment may be greater than room
ambient. Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specified by
the manufacturer.
3
4
Z
O
O
M
F
R
E
E
Z
E
S
E
A
R
T
C
H
E
L
E
M
E
N
W
U
ID
E
V
IE
W
DIGIT
AL VID
EO R
ER
SRD-
470D
[Figure 2]
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the
amount of air flow required for safe operation of the equipment is not compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is
not achieved due to uneven mechanical loading.
D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit
and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should
be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
English _13
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1133 1133
2010-04-30 오후 6:06:4488
installation
HDD ADDITION
You can install additional HDDs.
Make sure to unplug the power cord from the wall outlet to prevent possible electric shock, injury or product
damage.
Please consult your provider for further information on HDD installation since improper installation or settings may
damage the product.
Number of HDDs supported : SRD-470 : Default 1 HDD + Up to 1 HDD added
SRD-470D : Default 1 HDD
Make sure to unplug the power cord from the wall outlet before proceeding with the installation.
Cautions for data loss (HDD care)
J
Please pay attention so that the data inside the HDD is not damaged.
Before adding a HDD, please check the compatibility with this DVR product.
HDD is vulnerable to malfunction due to its sensitive nature especially against shock when operating.
Please ensure that the HDD is free from such shock.
We are not liable for any damage to the HDD incurred by user’s carelessness or miss use..
Cases might cause damage to HDD or recorded data
To minimize the risk of data loss from a damaged HDD, please backup data as often as possible.
Data may be lost due to external impacts during disassembly or installation of the DVR.
HDD may be damaged if the DVR is suddenly stopped by a power cut or power off during operation.
HDD or files stored inside may be damaged if the main body is moved or impacted during the HDD operation.
Cautions when adding a HDD
1. When adding a HDD, ensure that the cable does not get caught or the insulation does not come off.
2. Pay attention so as not to lose the disassembly screws or accessories.
If the screws or accessories are not put together correctly, the product may breakdown or not operate properly.
3. Please check the HDD compatibility before adding a HDD.
Please contact your nearest dealer to obtain the list of compatible devices.
14_ installation
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1144 1144
2010-04-30 오후 6:06:5511
1. First, loosen the screws on both sides and remove
the cover.
2. Loosen the left and right screws on the lower hard
disk bracket to remove it.
3. Insert the additional hard disk into the bracket and
fix it using the provided screws.
Hard disk bracket
Master hard disk
English _15
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1155 1155
2010-04-30 오후 6:06:5511
installation
4. Insert the bracket where the additional hard disk is
inserted into the lower bracket and fix it using the
provided screws.
5. When done, connect the power cable and connect
the signal cable (SATA cable) to the connector for
the main board.
SATA2
SATA1
6. Check if the connectors are properly connected
and there is no problem with wiring, and close the
cover and fix it with screws.
16_ installation
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1166 1166
2010-04-30 오후 6:06:5577
connecting with other device
CONNECTING THE VIDEO, AUDIO, AND MONITOR
VIDEO IN
AUDIO OUT
VIDEO OUT(VGA)
VIDEO OUT
AUDIO IN
MONITOR
SPOT OUT
CONNECTING THE USB
1. There is one USB port at the front and one at the back of the product.
2. You can connect a USB HDD, USB CD/DVD player, USB memory or mouse to the USB port.
3. If a USB HDD is connected to the system, recognition and settings are available in “Menu > Setting the Device >
Storage Device”. (Page 44)
4. This product supports hot-plugging, which connects/removes the USB device during the system operation.
If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the DVR.
J
CONNECTING POS DEVICE
1. You can connect a POS device to the RS-232C port on the product’s rear side when you connect it directly with
a RS-232C cable.
2. Connection setup for the RS-232C port is available in “Menu > Device > POS Devices”, press the
<POS Device Setup> button and set <Baudrate, Parity, Data, Stop bit and Transfer Type>. (Page 47)
English _17
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1177 1177
2010-04-30 오후 6:07:0033
connecting with other device
CONNECTING THE ALARM INPUT/OUTPUT
Connecting the alarm input signal
Connection port for the alarm input signal.
Connect one strand of the sensor signal line (two
strands) to the alarm input port and connect the other
to the [G] port.
Connecting the alarm output signal
Connection port for the alarm output signal.
Connect one strand of the sensor signal line
(two strands) to the alarm output port and connect
the other to the [COM] port.
ALARM IN ALARM OUT
CONNECTING THE RS485 DEVICE
Connect the rear [RS485 +, –] ports to the external device.
ex) you can connect and control the PTZ camera
M
which supports the RS485 communication.
Check if the RS485 device is compatible with the
product first.
Pay attention not to change the polarity (+/-) of the
RS485 device when connecting it.
Depending on camera’s type, connection polarity can
be different.
For further information, refer to the respective PTZ
Camera’s documentation.
RS485
18_ connecting with other device
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1188 1188
2010-04-30 오후 6:07:0055
CONNECTING THE NETWORK
Connecting to Internet through Ethernet (10/100/1000BaseT)
RJ-45 Ethernet Cable
(Direct Cable)
INTERNET
Back Bone
Hub/Switcher
Windows
Network Viewer
Hub/Switcher
Connecting to the Internet using the router
INTERNET
xDSL or Cable
xDSL or Cable
Modem
Modem
Router
External Remote
PC
DDNS Server
(Data Center)
English _19
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN1199 1199
2010-04-30 오후 6:07:0066
connecting with other device
Connecting to Internet through ADSL
RJ-45 Ethernet Cable
(Direct Cable)
INTERNET
Phone(ADSL) Line
ADSL MODEM
Windows
Network Viewer
Hub/Switcher
20_ connecting with other device
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2200 2200
2010-04-30 오후 6:07:0088
live
GETTING STARTED
Starting the system
1. Connect the power cable of the DVR to the wall outlet.
2. Press the Power button on the front panel.
REC
3. You will see the initialization screen.
The initialization process will last about 1 minute.
If a new HDD is installed, the initialization process may
take longer.
REC
4. The live screen appears with a beep.
Shutting Down the System
You can shut down the system only if you have logged in to the DVR.
You require permission to shut down the system if you are not logged in as admin.
1. Press the [POWER] button on the remote control or the
front panel, or right-click to display the context sensitive
menu and select <Shutdown>.
2. The “Shutdown” confirmation window appears.
Shutdown
Are you sure to shutdown?
OK Cancel
3. Use the arrow keys on the remote control or the front panel
to move to <OK> and press the [ENTER] button or click
<OK>.
The system will shut down.
For the permission management, refer to “Permission
M
Management > Setting Permissions”. (Page 37)
English _21
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2211 2211
2010-04-30 오후 6:07:0099
live
Login
To access a DVR or restricted menu, you should have logged in to the DVR.
1. In live mode, right-click any area of the screen.
You will see the context sensitive menu as in the right
figure.
Scene Mode ꢁ
Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Login
2. Click <Login>.
The login dialog appears.
You can also see the login dialog to access a desired menu
by pressing the [MENU] button on the remote control or
the front panel.
Login
x ID
admin
OK
x Password
The login dialog will also appear if you press a menu button on
the remote control or the front panel of the DVR when the
corresponding menu requires logging in.
Cancel
After logged in, press [RETURN] on the remote control to display
the logout dialog.
By default, initial ID and password are set to “admin”, and “4321”.
For the restricted permission, refer to “Permission Management > Setting Permissions”. (Page 37)
M
Locking All Buttons
This will restrict access to all buttons available in the DVR.
1. In Live mode, press buttons in the order of [STOP]
ꢀ
[FREEZE] [STOP] [FREEZE] [MENU].
ꢀ
ꢀ
ꢀ
All buttons will be locked.
2. In the lock condition, press any button to display a dialog
where you are prompted to enter the password for
unlocking the buttons.
Key Lock Password
x ID
admin
x Password
OK
Cancel
The button lock will be released if you enter the admin
password.
22_ live
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2222 2222
2010-04-30 오후 6:07:1144
LIVE SCREEN CONFIGURATION
Icons on the Live Screen
You can check the status or operation of the DVR with the icons on the live screen.
2010-01-01 00:00:01
CAM 01
Name
Description
Current Date, Time
Displays the current time and date.
Login Information
When you are logged in, the “LOG ON” icon will be displayed.
Displayed if the zoom function is activated.
Displayed if you press the Pause button.
Displayed in Auto Sequence mode where all channels are switched at the
Screen Mode
specific time interval.
Displayed if the recording is in process.
M To cancel the recording, enter the password.
Displayed if there is a problem with the cooling fan.
Displayed if the HDD is full and the DVR has an insufficient space to record.
Displayed if no HDD is installed or the existing HDD should be replaced.
Displayed if the HDD needs a technical examination.
System Operation
Video Input Status
Displayed if a new firmware is found from the network.
Displayed if no input is entered in the condition that the camera is set to <ON>.
Nothing will be displayed on the screen if the camera is set to <OFF>.
Camera Name/ Channel
Displays the camera name and the changed channel, if any.
Displays the resolution of the recording screen. (Page 52)
Displayed in PTZ setting, and highlighted yellow if PTZ is in operation.
Displays AUDIO ON/MUTE.
Not displayed in video mode if deactivated.
Camera Operation
If the sensor is set to <ON>, the input signal will be displayed on the screen of
the connected channel.
Displayed if a motion detected in the condition that the motion detection is set to
<ON>.
Displays the current record mode from Record/Event/Schedule.
English _23
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2233 2233
2010-04-30 오후 6:07:2200
livEerror Information
•
If you turn on the system when the internal HDD is not connected or an error occurs, the “HDD FAIL” icon
(
) will be displayed on the top left corner. In this case, make sure you contact the service center for
assistance as this may cause a failure of recording, playback or backup.
•
If the cooling fan does not work properly or has a problem, the <Fan Information> window will appear and
the fan error icon (
works.
) will be displayed on the top left corner. In this case, check to see if the internal fan
As a fan error can shorten the product life, make sure you contact the service center for assistance.
If you see the fan error icon or No HDD, HDD FAIL icons on the screen, contact the service center for more details.
M
Live Screen Menu
In addition to the buttons on the front panel or the remote control, you can access a desired menu by right-
clicking the mouse any area in live mode.
The context sensitive menu that appears by right-clicking the screen may differ, depending on the login/
logout, screen split mode and DVD operation mode.
Menu items of Search, Record, Backup, Shutdown and PTZ can be deactivated, depending on the user permission.
M
Scene Mode ꢁ
Scene Mode ꢁ
PTZ Control
Audio Off
ZOOM
Freeze
Audio
ꢁ
Stop Alarm
Record
Freeze
Stop Alarm
Record
Play
Play
Search
Search
Backup
Backup
Main Menu
Shutdown
Main Menu
Shutdown
Hide Launcher
Login
Hide Launcher
Login
PTZ
Alarm
Freeze
< Single Mode Menu >
< Split Mode Menu >
Split Mode Menu
The context sensitive menu in split mode differs, depending on the login/logout status.
Scene Mode
Spot Out
Audio Off
Freeze
ꢁ
ꢁ
1
2
3
4
Stop Alarm
Record
5
6
Play
7
Search
8
Backup
9
Main Menu
Shutdown
Hide Launcher
Logout
10
11
12
13
24_ live
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2244 2244
2010-04-30 오후 6:07:2222
Menu
Scene Mode
Spot Out
Audio On/Off
Freeze
Description
Refer to “Live Mode”. (Page 27)
Refer to “Spot Out”. (Page 29)
Refer to “Audio ON/OFF”. (Page 30)
Refer to “Freeze”. (Page 30)
Stop Alarm
Record/Stop
Play
Stops the alarm output and the event monitoring. Refer to “Event Monitoring”. (Page 30)
Starts/stops the standard recording.
Plays the search result (data). Refer to “Search & Play > Play”. (Page 69)
Refer to “Search & Play > Search”. (Page 66)
Refer to “Using the DVR > Setting the Backup”. (Page 56)
Accesses the main menu. Refer to the Using the DVR section. (Page 32)
Turns down the DVR.
Search
Backup
Main Menu
Shutdown
Show/Hide Launcher
Login/Logout
Shows or hides the launcher. Refer to “View the Launcher Menu”. (Page 26)
You can log in or out.
Single Mode Menu
The single mode menu is available only in Single Mode.
The context sensitive menu for the One Channel mode, in Split mode is different from that of the Single mode.
Full Screen
1
Spot Out
PTZ Control
ZOOM
ꢁ
ꢁ
2
3
Audio
Freeze
Stop Alarm
Record
Play
Shutdown
Hide Launcher
Logout
PTZ
Alarm
Freeze
Menu
Description
Select and click a desired channel in Split mode to switch to the full screen of the selected
Full Screen
channel.
Accesses the PTZ Control menu. The PTZ menu is activated only in One-Channel Live mode.
(Page 64)
Enlarges the selected image. (Page 29)
PTZ Control
ZOOM
English _25
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2255 2255
2010-04-30 오후 6:07:3300
live
View the Launcher Menu
The Launcher menu appears on the bottom of the live screen.
1. In Live mode, right-click to display the context menu and
select <Show Launcher>.
2. Move the cursor to the bottom and click a desired item in
the Launcher menu.
If no input is entered for 10 seconds, the menu will disappear.
M
The Launcher menu can be accessed only by using the mouse.
PTZ Alarm Freeze
Menu
Description
Displays the current time and date.
Date/Time
The indication of AM/PM is displayed if you set 12 hours for the time format in
“System > Date/Time/Language > Time”. (Page 32)
Screen Mode
Displays in the sequence of 4-split, PIP and Auto Sequence.
Menu Expansion Button Click to display the hidden menu to the right.
Audio
Zoom
PTZ
Turns ON/OFF the sound of the selected channel.
Enlarges the selected area. This is available only in Single Live mode.
Runs the PTZ Control launcher.
Alarm
Freeze
Play
Stops the alarm if it's activated.
Freezes the Live screen temporarily.
Enters Play mode if a file to play exist, and if not, enters Search mode.
Start/End recording the Live screen.
Record
26_ live
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2266 2266
2010-04-30 오후 6:07:3333
LIVE MODE
Displays 4 live video images in 3 different modes.
Switching the screen mode
To switch the split mode, select a screen mode in the launcher menu, or right-click to select a screen mode in
the context menu.
Press the [MODE] button on the front panel or the remote control to switch the mode in the sequence of the
launcher menu items.
CH1
CH3
CH2
ꢂ
ꢂ
CH2
CH4
CH1
CH1
4-split mode
PIP
Auto Sequence
Switching the screen automatically
With SRD-470/470D, you can display 4 live single screens in sequence.
4
CH1
1
Single mode
In Single mode, If you have set <SEQ-Dwell Time> in “Setting the Device > Camera”, Auto Sequence will be
M
conducted at the set interval. (Page 42)
English _27
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2277 2277
2010-04-30 오후 6:07:3355
live
Channel Setting
You can display the channel in a desired area of a split screen.
1. Place the cursor over the camera name of each channel to display the <
▼> key to the right on the screen.
2. Click a camera name to display a channel list where you can select a different channel.
3. Select a desired channel and click it.
The current channel will be switched to the selected one.
Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also
change the channel position.
Ex : if switching CH 1 to CH 4
CH4
CH3
CH2
CH1
CH1
CH3
CH2
CH4
ꢂ
Switching to Single Mode
When in split mode, select and double-click a desired channel to switch to its Single mode.
Press the number corresponding to a desired channel on the front panel or the remote control to switch to its
Single mode.
Refer to “Remote Control > Using the numeric buttons”. (Page 12)
Ex : If double-clicking CH 3 or pressing the number “3” on the remote control or the front panel.
CH1
CH3
CH2
CH4
ꢂ
CH3
28_ live
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2288 2288
2010-04-30 오후 6:07:3366
SPOT OUT
The Spot Out monitoring is independent of the Live mode, which monitors a specific channel through the Spot Out
port.
Selecting a Spot Out mode
If an event occurs such as sensor, motion or alarm from the Spot Out port in connection with a monitor, you
can select a output screen mode.
1. In Live mode, right-click any area on the screen.
Scene Mode ꢁ
Spot Out
Audio Off
Freeze
ꢁ
Spot Out 1
ꢁ
Auto Sequence
Single
The Live menu appears.
ꢁ
CH1
CH2
CH3
CH4
2. Click Spot Out.
Stop Alarm
Record
Supports the Spot output in Single screen with Auto
Sequence mode.
Play
Search
Backup
Main Menu
Shutdown
The Spot output is supported only for a designated channel.
For the Spot Out port of a model, refer to “Part Names and
Functions (Rear)”. (Page 9)
Hide Launcher
Logout
< Multichannel Live Menu >
ZOOM
This is available only in Single Live mode. In Single mode, select a desired area and use the Zoom function to
enlarge it twice.
1. Select <ZOOM> in the right-click menu.
Press the [ZOOM] button on the front panel or the remote control, or simply click <
> in the launcher
menu. The zoom box appears.
2. Use the direction keys, or drag and drop to specify an area to enlarge.
3. Press the [ENTER] button, or double-click the selected area to enlarge it twice.
In the enlarged image, use the direction buttons (ꢀꢁ◄ ►) on the remote control or the front panel to move the
enlarged area.
4. Press the [ZOOM] button on the front panel or the remote control, or simply click <
> in the launcher
menu to release the zoom.
ꢂ
English _29
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN2299 2299
2010-04-30 오후 6:07:3377
live
AUDIO ON/OFF
You can turn the sound on/off corresponding to the channel in Live mode.
AUDIO ON/OFF in Single mode
Click the audio icon ( ) on the screen, or press the [AUDIO] button on the front panel or the remote control
to turn it on/off.
Only the channel where <AUDIO> is set to <ON> in “Device > Camera” displays the audio icon ( ) in Live
M
mode that you can use to turn the sound on/off.
FREEZE
This is available only in Live mode, this pauses playing the Live image temporarily.
Freeze
1. Press the [FREEZE] button on the front panel or the remote control, or click <
> in the launcher
menu.
The playback of the image is stopped temporarily.
Freeze
2. Press the [FREEZE] button again, or click <
>.
This will release the freeze.
EVENT MONITORING
This will display the channel in sync with a specific event (Sensor/Motion/Video Loss) if it occurs.
In “Monitor > Event Display”, set the event monitoring to ON/OFF and specify the event display time. (Page 48)
•
•
If multiple events occur simultaneously, the screen will switch to a split mode.
- 2~4 events : 4-split mode
If the second event occurs within the set time of <Event Display>, the first event will last until the second
one is terminated. (Page 48)
Ex : If you set <Event Display> to 5 seconds, and only one event occurs in CH 1.
Event occurrence
5 seconds
Stop alarm
CH1
30_ live
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3300 3300
2010-04-30 오후 6:07:4466
Ex : If you set <Event Display> to 5 seconds, and the second event occurs in CH 2 within the set time after the first
event occurred in CH 1.
Event occurrence
4 seconds
9 seconds
Stop alarm
CH1
CH2
CH1
Press the [ALARM] button to reset the alarm settings and to release the event mode.
M
If an alarm activates in the condition you have set the event record, and pre/post alarm times, the event record will
be performed.
English _31
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3311 3311
2010-04-30 오후 6:07:4477
using the DVR
You can setup the system properties, devices, and options for recording, event,
backup and network.
SYSTEM SETUP
You can setup Date/Time/Language, Permission, System Properties and Log.
Date/Time/Language
You can check and setup the current Date/Time and time related properties, as well as the language used for
the interface on the screen.
Setting the Date/Time/Language
Set the Date/Time/Language
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control or on the
front panel.
If not logged in, it prompts with login window.
Refer to “Login”. (Page 22)
2. Use the left/right buttons (◄ ►) to select the <System>.
Logout
Exit
System property setup menu is selected.
3. Use the up/down buttons (ꢀꢁ) to select <Date/Time/
Language> and press the [ENTER] button.
System
Date/Time/Language
4. Select <Date/Time/Language>.
Permission Management
System Management
Log Information
A dialog to setup Date, Time and Language.
5. Use direction buttons (ꢀꢁ◄ ►) to select an item to set
and make your changes.
•
•
Date : Sets the date that will appear on the screen.
You can select the date format.
Time : Sets the time and its format that will appear on the
screen.
Date/Time/Language
Date/Time/Language
Holiday
x Date
2010-01-01
YYYY-MM-DD
24 Hours
x Time
08:14:24
GMT+09:00
Setup
Select either one from <24 Hours, 12 Hours (AM/PM)>.
x Time Zone
x Time Sync.
x DST
•
•
Time Zone : Sets the time zone of your area based on the
Greenwich Mean Time (GMT).
Dec First (Sun) 0
Dec First (Sun) 0
x Language
English
GMT (Greenwich Mean Time) is standard World Time and the basis
of world time zone.
OK
Cancel
Time Sync. : You can set the DVR’s current time
synchronized to a selected <Time Server> regularly if you select to use <Time Server>.
In this case, <Date/Time/Language> setup does not allow time adjustment.
32_ using the DVR
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3322 3322
2010-04-30 오후 6:07:4477
- Time Server : Enter an IP or URL address of the time
server.
Date/Time/Language
Date/Time/Language
Holiday
- Last Sync Time : Displays the most recent
synchronization time from the selected time server.
- Activate as Server : Set to <Use> to allow the DVR to act
as a Time Server for other DVRs.
x Time Synchronization Setup
x Synchronization
x
x Time Server
x
x Last Sync Time
x
x Activate as Server
x
Use
203.248.240.103
Fail
Use
•
•
DST : Set up Daylight Saving Time with its period to make
the time earlier than the GMT of its time zone by 1 hour
during the set period.
Language : Select your language. Sets the language for the
interface.
OK
OK
Cancel
Cancel
x Language
English
English, French, German, Spanish, Italian, Chinese, Russian, Korean, Polish, Japanese, Dutch, Portuguese,
Turkish, Czech, Danish, and Swedish are available.
6. When the Date/Time/Language setup is done, press <OK>.
You can also use numeric buttons on the remote control or front panel to enter values for Date, Time and other
M
numeric fields.
Setting Holiday
You can set specific dates to Holidays according to your preferences.
Holidays are applied to <Recording Schedule> and <Alarm Schedule> too.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <Date/Time/Language> window to select <Date/Time/Language>, and
press the [ENTER] button.
A calendar for Holiday setup appears.
4. Select <Holiday>.
Date/Time/Language
Holiday
Date/Time/Language
5. Use the left/right <
> buttons to select year or month,
2010
Sun Mon Tue
Jan
and press the [ENTER] button.
Wed Thu
Fri
1
Sat
2
3
4
5
6
7
8
9
10
17
24
31
11
18
25
12
19
26
13
20
27
14
21
28
15
22
29
16
23
30
OK
Cancel
6. Use direction buttons (ꢀꢁ◄ ►) to select a desired date,
and press the [ENTER] button.
Date/Time/Language
Holiday
Date/Time/Language
You will see the “Setting Holiday” screen.
2010
Jan
Ex : Select January 11th and check on <1/11> only to make
every January 11th a holiday. Check both on <1/11> and <Jan
2nd Mon> to make every January 11th and 2nd Monday of
January holidays.
Setting Holiday
1 / 11
Jan 2nd Mon
24
31
25
29
30
OK
Cancel
26
27
28
7. When the Holiday setup is done, press <OK>.
OK
Cancel
Using the Calendar
Using the mouse may help make setup easier.
{
Select year and month.
Select the left/right <
adjust by 1 year/month.
> key on the left/right side of year/month and press [ENTER] button to
|
Use direction buttons to select a date and press [ENTER] button.
A date with recorded data to be searched will appear in yellow in the System Log, Event Log, Time Search and Event
Search.
English _33
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3333 3333
2010-04-30 오후 6:07:5511
using the DVR
Permission Management
You can set permissions of each user over the DVR's specific function and settings.
Setting the Administrator
You can set and change Administrator’s ID and password.
The administrator can use and set all menu items and functions.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <System> window to
Permission Management
move to <Permission Management>, and press
Admin
Group
User
Setup
[ENTER] button.
x ID
admin
x Password
********
********
4. Select <Admin>.
x Confirm P/W
A dialog for Admin ID and Password input appears.
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired
item, and set the ID and password.
OK
Cancel
By default, initial ID and password are set to “admin”, and
M
“4321”.
6. When the administrator setup is done, press <OK>.
Using Virtual Keyboard
{
|
}
For alphanumeric inputs, the virtual keyboard window
appears.
`
1
w
s
2
e
d
c
3
r
4
t
5
6
u
j
7
i
8
o
l
9
p
;
0
[
-
]
=
\
ꢂ
Use direction buttons (ꢀꢁ◄ ►) to move to a desired
q
a
z
y
h
Del
character, and press the [ENTER] button.
f
g
b
k
,
‘
Caps Lock
Shift
x
v
n
m
.
/
In the upper text input box of the virtual keyboard, there
displays a list of candidate words containing the selected
character.
Space
Ctrl
OK
Cancel
~
Select a word from the list, or use the keyboard to enter the
whole word.
If there are many of candidate words, use <
,
> buttons to move between them forward and backward.
You can use mouse wheel and jog shuttle button too.
Select <OK>.
Entered word is applied.
For upper case letters, use <Caps Lock> button.
For special characters, use <Shift> button.
Using the virtual keyboard is the same to a normal keyboard use in your region.
You can enter only lower-case alphabets and numeric values for the user ID.
For the password, use alphabets and special characters excluding < > and <“>.
\
You can use number buttons on the remote control or front panel.
34_ using the DVR
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3344 3344
2010-04-30 오후 6:07:5544
Setting the Group
You can create user groups and setup permissions for those user groups.
You can register a user for each group in <User>.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <System> window to
Permission Management
move to <Permission Management>, and press
Group
Admin
User
Setup
[ENTER] button.
x Group
Add
Delete
Rename
Group Authority
Live View
Search
4. Select <Group>.
Setup
Setup
Setup
Setup
PTZ
A window for <Add>, <Delete>, <Rename>, and
Backup
Menu
<Group Authority> setup appears.
Record Lock
Remote Alarm Out
Shutdown
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired
item, and set the value.
OK
Cancel
•
Add, Delete, Rename : You can add, delete, rename a
group or modify the permissions given to the group.
The virtual keyboard appears when <Add> or <Rename> was selected.
You can add up to 10 groups.
- Add : When you first run the DVR with the admin account, only the admin account exists. Add has already
been deactivated. Select to display the virtual keyboard. Enter a group name. You can add up to 10
groups.
- Delete : Deletes a user group that is already registered. Selecting Delete will delete all user accounts
belonging to that group.
- Rename : Renames a group that is already registered. Select <Rename> to display the virtual keyboard.
For entering a group name, refer to “Using Virtual Keyboard”. (Page 34)
•
Group Authority : Sets permissions to access menu items of each group.
Users of a group can access checked functions.
6. When the group setup is done, press <OK>.
To set the group authority
You can set the permissions of the group users to access the menu according to the channel.
1. Select a menu to which the group permission is assigned.
Permission Management
The menu where the group permission is assigned will be
Group
Admin
User
Setup
displayed in the Live menu when a group user logs in.
Group
ABC
Add
Delete
Rename
x
Group A
Channel Setup
Live V
Searc
Backu
Menu
•
•
•
•
Live View : You can set the permission to access the Live
screen according to the channel.
All
1
2
3
4
Search : You can set the permission to access the Search
menu according to the channel.
Reco
Cancel
n
OK
Backup : You can set the permission to access the Backup
menu according to the channel.
OK
Cancel
Menu : You can set menus accessible with a specific
permission.
Group users can access the permitted menus only.
Select a menu to display the Menu Permission screen.
Permission Management
Menu Permission
All
System
t
B
a
c
k
u
p
N
e
t
w
ork
D
evice
Record
Eve
n
•
Record Lock, PTZ, Remote Alarm Out, Shutdown : Select
an item so that the item will be added to the permissions.
Date/Time/Language
Date/Time/Language
Holiday
Settings
System Management
System Information
Log Information
2. Select <OK>.
System Log
Event Log Backup Log
Select and assign a group user so that the user can
access the specified menu.
OK
Cancel
English _35
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3355 3355
2010-04-30 오후 6:07:5566
using the DVR
To restrict the user permissions
If the admin restricts all permissions of an added group, the users belonging to that group can access only
the default minimum menus and can change the user’s own password only.
1. Start the DVR.
If all permissions are restricted, only the Login dialog
should appear.
2. Log in with a registered user ID.
Login
x ID
abc
x Password
OK
Cancel
3. Right-click any area on the screen.
If all permissions are restricted, only the accessible context
menus should appear.
Scene Mode
ꢁ
Audio Off
Freeze
Stop Alarm
User Menu
Hide Launcher
Logout
To change the user password
If you log in with a user account that is restricted to access the menu, you can change your own password
only.
1. Log in with your account.
Permission Management
User
2. Select <User Menu>.
The Permission Management setup screen appears.
x ID
abc
x Password
x Confirm P/W
********
********
3. Select <Permission Management>.
The Password setup dialog appears.
4. Enter a new password.
5. Select <OK>.
OK
Cancel
You change to the password will be applied.
36_ using the DVR
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3366 3366
2010-04-30 오후 6:07:5599
Setting the User
Users can be added only if a group was created in <Group> menu.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <System> window to
move to <Permission Management>, and press
[ENTER] button.
Permission Management
User
Admin
x Group
Group
Group
All Group
Name
Setup
Add
Delete
ID
Viewer
4. Select <User>.
A window for Add User appears.
5. Use direction buttons (ꢀꢁ◄ ►) to select <Add> from the
window.
Previous/Next Page
A window for “Add User” appears.
OK
Cancel
You can configure the Network Viewer settings including
name, ID, viewer, Select Group and password.
Result of the user setup appears in the <User> window.
To change the user property, use “Edit User”.
The “Edit User” window appears when you select a
desired item to be changed in the <User> window.
Permission Management
User
Admin
x Group
Groux Name
Group
Setup
AddUser
Add
Delete
Kim
ksh
•
Viewer : If you select <Use>, you will be given access to the
x ID
x Viewer
Not Used
ABC
Web Viewer and Network Viewer.
x Select Group
x Password
x Confirm
********
********
Refer to “Connecting Web Viewer”. (Page 71)
OK
Cancel
For more information about use of Network Viewer, refer to the
Previous/Next Page
Network Viewer's user guide. (Page 8)
OK
Cancel
6. When the user setup is done, press <OK>.
Setting Permissions
You can set restricted access for all general users.
Items with restrictions will require logging in for use.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <System> window to
move to <Permission Management>, and press
[ENTER] button.
Permission Management
Setup
Admin
Group
User
Restricted Access
Live View
Backup
Remote Alarm Out
Record Lock
Shutdown
Search
All
PTZ
4. Select <Setup>.
Restriction on Network Access
The Restricted Access, Restriction on Network Access,
Auto Log out, Manual Input of ID setup screen appear.
All Network
Web Viewer
x Auto Log out
3 min
ON
x Manual Input of ID
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired
item, and set the value.
OK
Cancel
•
Restricted Access : All menu items allowed for a user can
be set with restricted access.
- Checked ( ) : Restricted
- Not checked ( ) : Accessible
If it is not checked ( ) in <Restricted Access>, any user can access the item no matter what the <Group Authority>
setting.
If it is checked ( ) in <Restricted Access>, a user can access the item only if the user has permission in <Group
Authority> setting.
•
•
Restriction on Network Access : Restricts remote access from a <Restricted Access> network.
- All Network : Restricts all access instances via Network Viewer and Web Viewer.
- Web Viewer : Restricts access via the Web Viewer.
Auto Log out : A user will be automatically logged out if there is no operation on DVR for over set period of
time.
English _37
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3377 3377
2010-04-30 오후 6:08:0022
using the DVR
•
Manual Input of ID : Prompts you to enter the user ID
manually for the login process.
- Checked ( ) : Encloses the registered user IDs with the
[
½
] symbols.
Login
x ID
Use the virtual keyboard to enter the user ID.
6. When the permission setup is done, press <OK>.
*****
x Password
OK
Cancel
System Management
You can check the system version, update to a newer version, as well as data backup and initialization.
Checking the System Information
You can check the current system version, broadcasting system, MAC address. You can update the system.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <System> window to
System Management
move to <System Management>, and press [ENTER]
System Information
Settings
button.
System Information
x Software Version
V1.00h_100315180929
x Broadcast Format
NTSC
4. Check the Version, Broadcast Format, and MAC Address.
x MAC Address
00:00:F0:54:FF:FF
•
System Information : Shows the current system’s
information.
S/W Upgrade
Upgrade
x Device
Network
x Version
No S/W Data
The values can not be changed by a user.
•
S/W Upgrade : Updates the DVR’s software up to date.
Previous
Ex : If you connect to a storage device that has upgradable software
installed, and return to the <System Management> menu, the
current software version will be displayed.
System Management
System Information
Settings
System Information
x Software Version
x Broadcast Format
x MAC Address
V1.00h_100315180929
NTSC
00:00:F0:54:FF:FF
S/W Upgrade
Upgrade
x Device
v3.1.0.4
x Version
V1.00h_100320180929
Previous
38_ using the DVR
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3388 3388
2010-04-30 오후 6:08:0055
•
Updating the Software
1. Connect a device storing the software to be updated.
System Management
System Information
(It may take about 10 seconds to recognize the device.)
Settings
System Information
Upgradeable devices include USB memory, CD/DVD and
x Software Version
V1.00h_100315180929
System Upgrade
x Broa
network device.
x MAC
Current Version
V1.00h_100315180929
New Version
V1.00h_100320180929
To update the network, the current DVR should have been
connected to the network.
S/W
Do you want to upgrade?
x Devi
OK
Cancel
x Vers
Upgrade via the proxy server may not be enabled due to the
restricted access.
Previous
2. Select <System Management> from <System> window.
3. Select <System Information>.
4. When the recognized device appears, select <Upgrade>.
The <Upgrade> button will be activated only if the current <Software Version> of the <System Information> is
same to or older than that of <S/W Upgrade>.
5. Press <OK> in the “System Upgrade” window.
System Management
System Information
While updating, it shows the progress.
Settings
System Information
•
Updating progresses with 3 steps as shown in the figure.
x Software Version
V1.00h_100315180929
x BroadcaS/WUpgrade
x MAC Ad
Software upgrading...
S/W Up
x Device
x Version
Previous
System Management
System Information
Settings
System Information
x Software Version
V1.00h_100315180929
x Broadca
S/W Upgrade
x MAC Ad
Software upgrading...
S/W Up
Do not turn off during the upgrade.
x Device
x Version
Previous
6. When the updating is done, it automatically restarts.
Do not turn the power off until it finishes restarting.
If “Upgrade Failed” appears, retry from the step 4.
M
When you experience continued failure, consult the service
center for assistance.
English _39
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN3399 3399
2010-04-30 오후 6:08:0088
using the DVR
Settings
You can copy and import the DVR settings by using a storage media.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <System> window to
move to <System Management>, and press [ENTER]
button.
System Management
Settings
System Information
x Storage Device
1932 MB (Remained Capacity)
Export
Import
x DVRꢃUSB
10041400
4. Select <Settings>.
x USBꢃDVR
Include Network Settings
A window of storage device and load factory default
appears.
x Load Factory Default
Default
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired
item, and export or import settings data to a storage
device.
Previous
•
•
•
Storage Device : Shows the connected storage device.
Export : Exports DVR settings to the connected storage device.
Import : Imports DVR settings from the storage device and applies to the DVR.
If <Include Network Settings> is checked, the network settings will be imported too.
•
Load Factory Default : If <Default> is selected, a
Press <OK> to initialize the system to the factory default.
System Management
confirmation dialog for “Load Factory Default” prompts.
Settings
System Information
x Storage Device
1932 MB (Remained Capacity)
Load Factory Default
x DVRꢃ
6. To move to the previous menu, press <Previous>.
x USBꢃ
Sure to Default Setting?
OK
Cancel
x Load
Previous
Log Information
You can browse logs on the system and events.
System Log
System Log shows log and timestamp on every system start up, system shutdown, and changes on system
settings.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <System> window to
Log Information
move to <Log Information>, and press [ENTER] button.
System Log
Event Log
Backup Log
Search
Search Day
First Page
2010-01-01
Last Page
4. Select <System Log>.
Type View all
No.
Log List
Date/Time
Refer to “Using the Calendar”. (Page 33)
Click on the calendar < > to display the calendar window.
•
Type : When there are too many logs, you can display logs of
the desired format by selecting the type.
Previous/Next Page
Previous
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired item,
and press <Search>.
40_ using the DVR
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4400 4400
2010-04-30 오후 6:08:1122
Event Log
Event log shows recorded events on alarms, motion detections and video loss.
It also shows the log and its timestamp.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <System> window to
Log Information
move to <Log Information>, and press [ENTER] button.
Event Log
System Log
Backup Log
Search Day
First Page
2010-01-01
Last Page
Search
All CHs
4. Select <Event Log>.
CH
Type
Date/Time
View all
No.
Log List
5. Use direction buttons (ꢀꢁ◄ ►) to move to the desired
7
6
5
4
3
2
1
Motion Detection [CH 1]
Motion Detection [CH 2]
Motion Detection [CH 3]
Motion Detection [CH 4]
Motion Detection [CH 3]
Motion Detection [CH 2]
Motion Detection [CH 1]
2010-01-01 00:02:14
2010-01-01 00:02:14
2010-01-01 00:02:14
2010-01-01 00:02:18
2010-01-01 00:02:18
2010-01-01 00:02:18
2010-01-01 00:02:18
item.
6. Set Search Day, Channel and Type and the press
<Search>.
Previous/Next Page
Refer to “Using the Calendar”. (Page 33)
Previous
Click on the calendar < > to display the calendar window.
Backup Log
You can find out who backed up and the details (backup time, channel, device to use, file format, etc.).
Using the mouse may help make setup easier.
3. In the <System> window, press the up/down (ꢀꢁ) button
Log Information
to move to <Log Information> and press the [ENTER]
Backup Log
System Log
Event Log
Search Day
First Page
2010-01-01
Last Page
~
2010-01-02
Search
button.
Previous/Next Page
No.
User
Date/Time
4. Select <Backup Log>.
5. Use the four direction buttons (ꢀꢁ◄ ►) to move to a
desired item.
6. Specify a search term and select <Search> in the right
corner.
Previous
Backup details for the search term will be listed.
English _41
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4411 4411
2010-04-30 오후 6:08:1155
using the DVR
SETTING THE DEVICE
You can setup Camera, Storage Device, Remote Device, POS Device and Monitor.
Camera
Setting the Camera
You can set Video, Audio, Channel Name and Dwell Time of a Camera.
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control or front
Logout
Exit
panel.
2. Use the left/right button (◄ ►) to select <Device>.
Device setting menu is selected.
Device
Camera
3. Use the up/down buttons (ꢀꢁ) to move to <Camera>,
Storage Device
Remote Device
POS Device
Monitor
and press [ENTER] button.
4. Select <Camera>.
Camera
Camera
You will see a window where you can configure the
PTZ
camera settings including Video, Audio, Channel Name,
Dwell Time and Progressive.
CH
1
Video ꢄ
Audio ꢄ
OFF ꢄ
OFF ꢄ
OFF ꢄ
OFF ꢄ
CH Name
SEQ-Dwell Time ꢄ Progressive ꢄ
ON ꢄ
ON ꢄ
ON ꢄ
ON ꢄ
CAM 01
CAM 02
CAM 03
CAM 04
5 sec
5 sec
5 sec
5 sec
ꢄ
ꢄ
ꢄ
ꢄ
OFF ꢄ
OFF ꢄ
OFF ꢄ
OFF ꢄ
2
3
4
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired
item, and set the value.
•
Video
Screen Setup
- <ON/OFF> : You can turn ON/OFF the selected
OK
Cancel
channel’s camera.
- <Covert1> : Shows information other than the video of the selected channel.
For privacy protection, it does not display the video while the recording continues.
- <Covert2> : Shows nothing but an empty screen while the recording continues.
•
Audio
- If set to <ON>, you can turn the audio of the channel ON/OFF on the Live screen.
- If set to <OFF>, the channel’s audio is off on the Live screen and not recorded.
Audio output is available for only 1 channel.
•
•
CH Name : Up to 15 characters including blanks are allowed.
Refer to “Using Virtual Keyboard”. (Page 34)
SEQ-Dwell Time : You can set the dwell time between channels for the Live screen and Spot Out.
If set to <OFF>, the channel is not listed in the Auto Sequence mode.
42_ using the DVR
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4422 4422
2010-04-30 오후 6:08:1177
•
Progressive : You can set the progressive camera to ON/OFF.
If you set it to <ON> for the progressive camera, screen flickering will be reduced.
J
•
Screen Setup : The video appeared on the screen may vary
depending on the channel’s camera, configure the DVR
display to your preferences.
Select a channel and adjust the
<
(Brightness)>,
<
(Contrast)>, and
<
(Color)> of the selected channel.
•
Press the <Init> to initialize settings back to the default 50.
Screen Setup
6. When the camera setup is done, press <OK>.
CH1
50
50
50
Init
Apply to All CH
OK
Cancel
Setting the PTZ
To use Camera’s PTZ functions, ID and protocols of each camera and DVR should be matched.
For other settings, refer to the “Remote Devices” settings. (Page 46)
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <Device> window to
Camera
move to <Camera>, and press [ENTER] button.
PTZ
Camera
CH
1
ID
Protocol ꢄ
4. Select <PTZ>.
0
1
2
3
None
None
None
None
ꢄ
ꢄ
ꢄ
ꢄ
>
>
>
>
2
A window of PTZ settings appears.
3
4
5. Use direction buttons (ꢀꢁ◄ ►) to move to a desired
item, and select it.
•
ID : Set the ID of the connected camera of each channel.
You can easily setup by using the numeric buttons on the
remote control or front panel.
OK
Cancel
•
Protocol : Set the protocol of the connected camera of each
channel.
You can check the camera’s ID and protocol if you turn the camera off and on after connecting it to the DVR.
M
(Page 65)
6. When the PTZ setup is done, press <OK>.
English _43
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4433 4433
2010-04-30 오후 6:08:1199
using the DVR
Storage Device
You can check information on storage devices.
Confirming Devices
You can check storage devices and their free space, usage as well as status.
Devices available are HDD, and USB devices (Memory, HDD, CD/DVD).
Refer to “Product Specifications > Backup”. (Page 96)
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <Device> window to
Storage Device
move to <Storage Device>, and press [ENTER] button.
Device
Format
HDD Alarm
Device
HDD
No.
1
Used/Total
12.28G/499.37G
Usage
Status/Management
Normal
4. Select <Device>.
Internal
•
No. : Shows the assigned number of the internal HDD.
To see the detailed positioning of the HDD according to the
number, refer to <HDD Map>.
HDD Map
•
•
•
Used/Total : Shows the used/total capacity of the storage
device.
Usage : Sets the storage device’s usage.
- USB memory and storage media such as CD/DVD are used for backup purpose only.
Status/Management : Shows the current status of the HDD, as in Normal/Check/Replace.
OK
Cancel
- Normal : Available to use
- Check : Available to use but recommended to replace
- Replace : Requires immediate replacement.
•
HDD Map : Shows the internal HDD’s locations according
HDD Map
to assigned numbers.
Refer to this for servicing or additional HDD installation.
5. To move to the previous menu, press <OK>.
OK
<SRD-470>
HDD Map
OK
<SRD-470D>
44_ using the DVR
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4444 4444
2010-04-30 오후 6:08:2255
Formatting
You can format a storage device.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <Device> window to
Storage Device
move to <Storage Device>, and press [ENTER] button.
Format
Device
HDD Alarm
Device
HDD
Select
1
Used/Total
12.28G/499.37G
Usage
4. Select <Format>.
Internal
A window for selection of device for formatting appears.
5. Use direction buttons (ꢀꢁ◄ ►) to select a device to be
formatted.
Format
OK
Cancel
6. Select <Format> on the bottom of the screen.
Press <OK> on the “Manage” confirmation window will
start formatting the selected device.
Storage Device
Format
Device
HDD Alarm
Device
HDD
Select
1
Used/Total
Usage
12.28G/499.37G
Internal
7. When the formatting is done, press <OK>.
Manage
Formatting deletes all recordings.
Proceed formatting?
OK
Cancel
Format
OK
Cancel
HDD Alarm
You can set alarm settings for HDD defects such as Check Alarm Output Port, Replace Alarm Output Port,
and its duration.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <Device> window to
Storage Device
move to <Storage Device>, and press [ENTER] button.
HDD Alarm
Device
Format
4. Select <HDD Alarm>.
1
2
BEEP
BEEP
x Check Alarm Output Port
All
A window for setting HDD check and replace output ports
and their durations appears.
x Duration
OFF
x Replace Alarm Output Port
1
All
2
5. Use direction buttons (ꢀꢁ◄ ►) to move to the desired
x Duration
OFF
item.
•
Alarm
OK
Cancel
- Alarm signal will output through the alarm out port on the
rear side when selected <1>, <2>.
- If <BEEP> was selected, a beep will sound.
- If <All> was selected, both beep sound and alarm signal through rear side ports will output.
•
•
Check Alarm Output Port : If HDD generates check alarm, the alarm signal will output to the specified alarm
output port.
Replace Alarm Output Port : If HDD generates replace alarm, the alarm signal will output to the specified
alarm output port.
English _45
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4455 4455
2010-04-30 오후 6:08:3333
using the DVR
•
Duration : Sets the alarm duration for the alarm signal and beep sound.
- If <BEEP> was selected, a beep will sound.
- If <All> was selected, both beep sound and alarm signal through rear side ports will output.
<Check> status means that the HDD is operating but it has problems that require technical examination.
M
(
) appears on the Live screen.
<Replace> status means that the HDD has defect and requires immediate replacement.
) appears on the Live screen.
(
6. When the HDD Alarm setup is done, press <OK>.
Remote Devices
You can set the RS-485 communication for use of PTZ Camera and system keyboard with the DVR.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <Device> window to
Remote Device
move to <Remote Device>, and press [ENTER] button.
Baudrate
9600
Parity
None
Data
8
Stop Bit
1
Transfer type
Half Duplex
ꢄ
ꢄ
ꢄ
ꢄ
4. Use direction buttons (ꢀꢁ◄ ►) to move to the desired
item, and press [ENTER] button.
System Keyboard
Remote Control
OFF
ON
ID
ID
00
00
5. Set the values of each communication setup of the remote
device.
•
Baudrate : Baud rate settings of the DVR, PTZ camera and
system keyboard should be matched for proper operations.
OK
Cancel
6. Make sure to match IDs of the DVR, System Keyboard
and Remote Control, and press <OK>.
For changing the remote control’s ID, refer to “Changing the Remote Control ID”. (Page 12)
M
POS Devices
You can set properties of POS devices connected to the DVR.
A POS device connection requires channel, preset, and Port/Ethernet settings.
Using the mouse may help make setup easier.
3. Use the up/down buttons (ꢀꢁ) in <Device> window to
POS Device
move to <POS Device>, and press [ENTER] button.
POS USE
POS Device Setup
POS
CH
Preset ꢄ
No preset
No preset
No preset
No preset
Port/Ethernet
None
4. Use direction buttons (ꢀꢁ◄ ►) to move to a desired
1
2
3
4
None
None
None
None
None
item, and set the value.
None
None
•
POS USE : When selected <POS USE>, DVR and POS will
be connected.
If you change settings for the device and press <OK> while
OK
Cancel
J
the <POS USE> is not checked, the changes for POS device
will not be saved.
46_ using the DVR
Z6806127401A_SRD-47700,, 447700DD--IIBB__EENN4466 4466
2010-04-30 오후 6:08:3366
|