2X, 3 X
A N D
5 X
E
L E C T R O N I C
C
R O S S O V E R
O
W N E R
’
S
M
A N U A L
T A B L E O F C O N T E N T S
Punch 2X, 3X and 5X Packing List................................................ 1
Introduction ................................................................................. 1
Operating Features ................................................................. 1
Design Features............................................................................ 2
1. Gold Plated RCA Jacks ....................................................... 3
2. Power Terminals ................................................................ 3
3. LED Power Indicator .......................................................... 3
4. PROCards .......................................................................... 3
5. Input Mode Switch (3X and 5X only) .................................. 3
6. Phase Switch (3X and 5X only) ........................................... 4
7. Mounting Holes ................................................................. 4
8. Fusing ................................................................................ 4
Installation Considerations ........................................................... 5
Mounting and Wiring the Active Crossover .................................. 6
B+ .......................................................................................... 6
GND ...................................................................................... 6
REM ....................................................................................... 6
Input/Output Levels & Connections ........................................ 6
Selecting the PROCards ............................................................... 7
Using The Dual Filter (3X and 5X only) ........................................ 8
Installing the PROCards ............................................................... 8
Filter Effects.................................................................................. 9
Wiring Diagrams ........................................................................ 10
Appendix A - Building A Custom PROCard ................................ 18
Butterworth Resistor Chart.......................................................... 19
Specifications ............................................................................. 20
Warranty .................................................................................... 21
P U N C H 2X/ 3 X/ 5 X P AC KI N G LI ST
Punch Electronic Crossover
Owner's Manual
I N T R O D U C T I O N
This manual provides information on the features, installation and
operation of the Punch 2X, 3X and 5X Electronic Crossover. We
suggest you save this manual for future reference.
We strongly recommend you have your Authorized Rockford Fosgate
Dealerinstallyournew active crossover. Ifyou do choose to installthe
unit yourself, please be sure to read the entire manual before begin-
ning your installation.
OPERATING FEATURES
The Punch 2X, 3X and 5X Electronic Crossovers provide for state-of-
the-art flexibility and performance demanded by today’s car audio
enthusiasts. Features include:
PROCards – 3-Way Selectable Electronic Crossover modules that
feature 12dB per octave filters that give precise crossover points and
allow for individual selection of high-pass, low-pass or full range filter
operation.
Dual Filtered, Non-Faded Output with Phase Reversal Switch (3X
and 5X only) allows you to create various pass band configurations.
In addition, the phase reversal switch enables you to easily correct for
phase problems that may be inherent in some system designs.
2 Channel Input on the Punch 2X
2 or 4-Channel Input Mode Switch (3X and 5X only) enables you to
select two (2) or four (4) channels of input.
4 Outputs on the Punch 2X
6 Outputs on the Punch 3X for Front, Rear and a Dual-Filtered, Non-
Faded Output.
10 Outputs on the Punch 5X – In addition to the outputs found on the
Punch 3X, the 5X also has Front and Rear Dual-Filtered Outputs for
creating additional pass band filter combinations.
Gold Plated RCA Input and Output Jacksreduce corrosion which can
cause signal deterioration over time.
– 1 –
D E S I G N FE A T U R E S
REMOVING THE COVER
The design of the 2X, 3X and 5X allows the cover to be removed for
access to the crossovers and ease of installation. The cover can be
installed in eitherdirection to match the restofthe system. The top end
of the cover has two tabs which fit snugly into slots at either end of the
base. Care mustbe taken notto bend the securingtabswhen removing
the top cover. A screw secures the cover. Remove this screw to release
the cover for removal.
Punch 2X - Top Inside View
8
Input
3
1
Rem
B+
Output
Output
1
GND
4
2
7
Punch 3X - Top Inside View
5
6
7
8
Front Input
1
Rear Input
3
Front Output
Rem
B+
Dual Filtered Non-Faded Output
Rear Output
1
GND
4
2
7
– 2 –
6
7
8
5
Punch 5X - Top Inside View
Front Input
1
Rear Input
3
Front Output
Front Dual-Filtered Output
Dual Filtered Non-Faded Output
Rear Dual-Filtered Output
Rear Output
1
Rem
B+
GND
7
2
4
1. Gold Plated RCA Jacks
All input and output RCA jacks are gold plated. The gold plated
finish resists tarnishing and corrosion from interfering with the
signal quality.
2. Power Terminals
The B+, Rem and Gnd connections are made using gold plated
screw terminals on the barrier strip. The gold plating resists tarnish
and corrosion and maintains connection integrity. The terminals
allow easy connection of the power wires through the use of forked
lugs or bare wire up to 12 gauge. The barriers help prevent shorting
from frayed wires.
3. LED Power Indicator
The LED, located by the input jacks, provides a visual indication of
the status of the crossover, lighting when the unit is turned on.
4. PROCards
Crossover filter functions are determined by the use of plug in
cards. Each card can be configured for high-pass, low-pass and full
range operation. Resistors on each module determine the operat-
ing frequency.
5. Input Mode Switch (3X and 5X only)
When the input mode switch is in the two channel position the
front input jacks feed all the filters. When set to the four channel
position, the front and rear input jacks feed the respective filters.
Front and rear channels are summed for the non-faded filter.
– 3 –
6. Phase Switch (3X and 5X only)
The phase switch allows easy invertion polarity on the non-faded
output to optimize sound quality.
7. Mounting Holes
The crossover must be mounted on a flat surface. Two mounting
holes in the bottom are used to secure the crossover.
8. Fusing
The crossover has a 1/2 amp AGC fast blow power protection fuse.
If it is necessary to replace the fuse, use only the same type and
rating or the warranty may be voided.
– 4 –
I N STA L L AT I O N C O N SI D E R AT I O N S
This section focuses on some of the vehicle considerations for
installing your new Punch Electronic Crossover. Checking your
battery and current sound system, as well as pre-planning your system
layout and best wiring routes will save installation time. When
deciding how to lay out your new system, be sure that each compo-
nent will be easily accessible for making adjustments.
Before beginninganyinstallation, be sure to follow these simple rules:
1. Be sure to carefully read and understand the instructions before
attempting to install the crossover.
2. For safety, disconnect the negative lead from the battery prior to
beginning the installation.
3. For easier assembly, we suggest you run all wires prior to
mounting your electronic crossover in place.
4. Route all of the RCA cables close together and away from any
high current wires. this will help reduce noise.
5. Use high quality connectors for a reliable installation and to
minimize signal or power loss. See your Authorized Rockford
Fosgate Dealer for wire enhancements.
6. Think before you drill! Be careful not to cut or drill into gas tanks,
fuel lines, brake or hydraulic lines, vacuum lines or electrical
wiring when working on any vehicle.
7. Never run wires underneath the vehicle. Running the wires
inside the vehicle provides for best protection.
8. Avoid running wires over or through sharp edges. Use rubber or
plastic grommets to protect any wires routed through metal,
especially the firewall.
9. ALWAYS protect the battery and electrical system from damage
with proper fusing. Install a fuse holder and fuse on the +12V
power wire within 18” (45.7 cm) of the battery terminal.
10. When grounding to the chassis of the vehicle, scrape all paint
from the metal to ensure a good, clean ground connection.
Groundingconnectionsshould be asshortaspossible and always
be connected to metalthatiswelded to the main body, orchassis,
of the vehicle. Use of a continuity meter will confirm a proper
ground.
– 5 –
M O U N T I N G A N D W I R I N G T H E
E L E C T R O N I C C R O S S O V E R S
The information below describes the various considerations for
mounting and connecting the active crossovers. For additional infor-
mation see the wiring diagrams beginning on page 10.
We recommend mounting the crossover as close to the amplifier(s) as
possible.
The B+ (Power) supplies power to the unit. Connect this terminal to
a constant +12 Volt power source by way of an in-line fuse.
The GND (Power Ground) grounds the unit. Connect this terminal to
the chassis of the vehicle. When grounding the unit be sure to scrape
all paint from the metal to ensure a clean electrical connection.
The REM (Remote Turn-On) turns on the unit by way of a +12 Volt
supply source. Connect this terminal to the source unit’s “Amplifier”
or “Auto Antenna” lead, either of which will go to +12 volts whenever
the source unit is on.
If your source unit does not have either a Remote or an Auto Antenna
lead (or if the Auto Antenna goes down during tape operation), we
recommend installing a switch to control the unit manually.
INPUT/OUTPUT LEVELS & CONNECTIONS
The Punch Electronic Crossovers are designed for preamp (input up
to 2VRMS) levels. Net gain in the crossover is unity. (Output levels are
equal to input levels.)
When connecting the input and output terminals be sure to use high
quality shielded interconnecting RCA cables.
• Connect source unit's OUTPUT jacks to the desired crossover
INPUT jacks.
• Connectthe desired crossover’sOUTPUTjacksto the Amplifier’s
INPUT jacks.
– 6 –
SELEC TI N G TH E PROCARD S
The Punch 2X is shipped with 100Hz cards. The 3X is shipped with
100Hz and blank programmable cards and the 5X is shipped with
100Hz, 6.5kHz and blank programmable cards. The following cards
are available factory built from your Authorized Rockford Fosgate
Dealer.
XM275
XM400
XM4.5k
XM6.5k
275Hz
400Hz
4.5kHz
6.5kHz
XM50
XM70
XM100 100Hz
XM150 150Hz
XM200 200Hz
50Hz
70Hz
Each card can be used for high-pass, low-pass or full range operation.
The mode ofoperation isdetermined bythe orientation ofthe ProCard
in its socket. These same PROCards are used in other Rockford
Fosgate products.
The following illustrations show the PROCards shipped in the Punch
2X, 3X and 5X. As configured, out of the box, each card is set for full
range operation.
Punch 2X
100 Hz
Output
100 Hz
Output
Punch 3X
100 Hz
Front Output
Blank
100 Hz
100 Hz
Dual Filtered
Non-Faded Output
Rear Output
– 7 –
Punch 5X
6.5kHz
100Hz
Front Output
Blank
Front Dual
Filtered Output
Dual Filtered
Non-Faded Output
100Hz
100Hz
6.5kHz
Blank
Blank
Rear Dual
Filtered Output
Rear Output
U S I N G T H E D U A L FI LT E R
The Punch 3X and the Punch 5X both have Dual Filter sections. The
Dual Filter is a two stage cascaded filter which uses two PROCards.
The first card determines the initial action and the second, the
subsequent action. The most common usage would be to use a low-
passmodule in the firstposition followed bya high-passmodule in the
second to build a bandpass function. By using two cards of the same
action at the same frequency, the filter slope is increased to 24dB per
octave. Both sockets must be used for a simple 12dB per octave filter.
Install the card in the second position for full range operation.
IN STALLIN G TH E PROCARD S
The operation of each filter section is determined by the use of plug
in cards. These multifunctional cards are available for a multitude of
operational frequencies, and their orientation in the socket deter-
mines their function. Each socket has a blank plastic side which
positions the card against the spring loaded contacts. The front, or
active, face of the card is marked with arrows to indicate which edge
plugs into the socket. Orient the card with the chosen face toward the
contacts and plug it into the socket of the appropriate filter operation.
The rear face of the card is for full range operation and either edge can
be used.
– 8 –
F I L T E R E F F E C T S
Example: The Punch 3X ships with three (3) 100Hz PROCards set in
the Full Range position. The crossover will pass through all 20Hz -
20kHz frequencies. The following diagram shows examples of the
types of response curves when programming for a High-Pass, Low-
Pass or Bandpass setting.
Gain
(dB)
20Hz
20kHz
High-Pass Crossover Setting Response
Gain
(dB)
20Hz
20kHz
Low-Pass Crossover Setting Response
Gain
(dB)
20Hz
20kHz
Bandpass Crossover Setting Response
(3X and 5X only)
Note: The Punch 3X and 5X Dual-Filtered Output Channels contain a blank
crossover card. As with the Front and Rear Outputs, the default positioning
for these cards is set at Full Range.
– 9 –
W I R I N G D I A G R A M S
2X Basic System
Source Unit
Low-Pass
High-Pass
®
®
2
2X Crossover
Midrange/
Tweeter
High-Pass
@ 12dB/octave slope
–
+
–
+
Midrange/
Tweeter
2-Channel Amplifier
+
Low-Pass
@ 12dB/octave slope
–
Midrange/
Woofer
4Ω
+
–
+
–
2-Channel Amplifier
FIGURE 1
– 10 –
2X - 2 Way with Passive Crosovers
Source Unit
Low-Pass
High-Pass
®
®
2
High-Pass
@ 12dB/octave slope
Tweeter
2X Crossover
Passive
Crossover
Midrange
–
+
–
+
Passive
Crossover
Midrange
Tweeter
2-Channel Amplifier
+
Woofer
4Ω
Low-Pass
@ 12dB/octave slope
–
–
+
–
+
–
Woofer
4Ω
2-Channel Amplifier
+
FIGURE 2
– 11 –
3X – 2-Way with Passive Crossovers
Source Unit
2
4*
0°
180°**
High-Pass
Low-Pass
High-Pass
Low-Pass
®
®
3
High-Pass
Crossover
3x Crossover
Tweeter
Rear High-Pass
@ 12dB/octave slope
Midrange
–
+
–
+
Midrange
2-Channel Amplifier
Tweeter
+
High-Pass
Crossover
Subwoofer
Subwoofer
Summed Output
@ 24dB/octave slope
–
–
+
–
+
–
2-Channel Amplifier
High-Pass
Crossover
+
Tweeter
Midrange
Front High-Pass
@ 12dB/octave slope
–
+
–
+
Midrange
2-Channel Amplifier
Tweeter
High-Pass
Crossover
*2 or 4 Channel can be selected if user desires fader capability.
** Try Phase Switch for summed output and set to position that sounds best.
FIGURE 3
– 12 –
3X – 3-Way Basic System
Source Unit
2
0°
4*
180°**
High-Pass
Low-Pass
Low-Pass
High-Pass
®
®
3
3x Crossover
+
Subwoofer
Low-Pass
–
@ 12dB/octave slope
–
+
–
+
–
Subwoofer
2-Channel Amplifier
+
Midrange
Bandpass Output
@ 12dB/octave slope
–
+
–
+
Midrange
2-Channel Amplifier
High-Pass Output
@ 12dB/octave slope
–
Tweeter
Tweeter
+
–
+
2-Channel Amplifier
* Try Phase Switch for summed output and set to position that sounds best.
FIGURE 4
– 13 –
3X – 2-Way with Amplifier's Active Crossover
Source Unit
2
0°
4*
180°**
High-Pass
Low-Pass
High-Pass
Low-Pass
®
®
3
3x Crossover
Rear High-Pass
@ 12dB/octave slope
Tweeter
–
+
Tweeter
–
+
–
+
Rear Bandpass
Midrange
Both rolloffs @ 12dB/octave slope
–
+
4-Channel Amplifier
with Crossover***
(High-Pass)
Midrange
(Low-Pass)
Summed Output
@ 24dB/octave slope
–
–
+
Subwoofer
–
+
+
2-Channel Amplifier
Front High-Pass
@ 12dB/octave slope
Tweeter
–
+
Tweeter
–
+
–
+
Midrange
Front Bandpass
–
Both rolloffs @ 12dB/octave slope
+
4-Channel Amplifier
with Crossover***
(High-Pass)
Midrange
(Low-Pass)
*2 or 4 Channel can be selected if user desires fader capability.
** Try Phase Switch for summed output and set to position that sounds best.
*** Additional filtering provided by internal crossovers in the amplifiers.
FIGURE 5
– 14 –
5X – Basic System
Source Unit
2
0°
4*
180°**
High-Pass
Low-Pass
Low-Pass
Low-Pass
High-Pass
High-Pass
®
Low-Pass
High-Pass
®
5
5x Crossover
Rear High-Pass
@ 12dB/octave slope
–
Tweeter
Tweeter
+
–
+
2-Channel Amplifier
Front Bandpass
Both rolloffs @ 12dB/octave slope
Midrange
–
+
–
+
Midrange
2-Channel Amplifier
Summed Output
@ 24dB/octave slope
–
–
+
Subwoofer
–
+
+
2-Channel Amplifier
Midrange
Front Bandpass
Both rolloffs @ 12dB/octave slope
–
+
–
+
Midrange
2-Channel Amplifier
Front High-Pass
@ 12dB/octave slope
–
Tweeter
Tweeter
+
–
+
2-Channel Amplifier
*2 or 4 Channel can be selected if user desires fader capability.
** Try Phase Switch for summed output and set to position that sounds best.
FIGURE 6
– 15 –
5X – 2-Way with 24dB Slopes
Source Unit
2
0°
4*
180°**
Not Used
High-Pass
Low-Pass
High-Pass
Not Used
High-Pass
Low-Pass
High-Pass
Not
Used
®
®
5
5x Crossover
Not
Used
Midrange/Tweeter
Midrange/Tweeter
Rear High-Pass
@ 24dB/octave slope
–
+
–
+
2-Channel Amplifier
–
Summed Output
@ 24dB/octave slope
–
+
Subwoofer
–
+
+
2-Channel Amplifier
Midrange/Tweeter
Midrange/Tweeter
Front High-Pass
@ 24dB/octave slope
–
+
–
+
2-Channel Amplifier
*2 or 4 Channel can be selected if user desires fader capability.
** Try Phase Switch for summed output and set to position that sounds best.
FIGURE 7
– 16 –
5X – 4-Way System
Source Unit
2
0°
4
180°**
Not Used
Low-Pass
Low-Pass
Low-Pass
High-Pass
High-Pass
®
Low-Pass
High-Pass
®
5
5x Crossover
High-Pass
@ 12dB/octave slope
–
Tweeter
Tweeter
+
–
+
2-Channel Amplifier
Bandpass
Both rolloffs @ 12dB/octave slope
Midrange
–
+
–
+
Midrange
2-Channel Amplifier
Low-Pass
@ 24dB/octave slope
–
–
+
Subwoofer
–
+
+
2-Channel Amplifier
Mid Bass
Mid Bass
Bandpass
Both rolloffs @ 12dB/octave slope
–
+
–
+
2-Channel Amplifier
Not Used**
*2 or 4 Channel can be selected if user desires fader capability.
** Try Phase Switch for summed output and set to position that sounds best.
FIGURE 8
– 17 –
AP P EN D I X A
BUILDING A CUSTOM PROCARD
The 3X and 5X both ship with blank cards which can be assembled
to select any frequency you need for your system's design. Each card
is built using 4 capacitors and 4 resistors, the value of the resistors
determines the operating frequency. The custom cards are also
available as model number XM00 from your Authorized Rockford
Fosgate Dealer. The following section has instructions on assembling
the card. The PC Board is fragile and extra care should be taken to
avoid damage.
Items Needed:
1. Soldering Pencil
40 to 60 Watt electronic soldering iron
2. 60/40 resin core solder
3. Solder Braid - to keep surface free of excess solder
4. Capacitors - Each card uses four .022µF capacitors. These should
be metal film capacitors with a minimum rating of 16 volts.
5. Resistors - Each card uses four resistors. The resistance is deter-
mined by the operating frequency (refer to the following chart).
These can be either 1/8 or 1/4 Watt, 1% or 5% tolerance.
6. Wire Cutters
Refer to the following illustration for component placement. Install
the resistors, from the fullrange face, and fold the leadsslightlytoward
the inside of the board to hold them in position. Solder the resistors
in place and use the solder braid to remove any excess solder. Install
the capacitors in the same manner. Trim the component leads.
Examine the board carefully to ensure there is no solder splashed,
paying particular attention to the contacts on each edge. Make sure
that the leads do not interfere when plugging the card into the socket.
Crossover Card
Hh Pass
FUL
LoPass
Ful Range
– 18 –
Electron ic Crossover Field Progra m m a ble Ca rd Resistor Cha rt
Butterworth Align m en t
Use 5% resistors in conjunction with .022µF standard capacitor.
Low Pass
High Pass
R2
R2
Freq.
18.5Hz
26Hz
R1
R1
390k Ohm
270k Ohm
220k Ohm
180k Ohm
150k Ohm
120k Ohm
100k Ohm
82k Ohm
68k Ohm
56k Ohm
47k Ohm
39k Ohm
33k Ohm
27k Ohm
22k Ohm
18k Ohm
15k Ohm
12k Ohm
10k Ohm
8.2k Ohm
6.8k Ohm
5.6k Ohm
4.7k Ohm
3.9k Ohm
3.3k Ohm
2.7k Ohm
2.2k Ohm
1.8k Ohm
1.5k Ohm
1.2k Ohm
1k Ohm
390k Ohm
270k Ohm
220k Ohm
180k Ohm
150k Ohm
120k Ohm
100k Ohm
82k Ohm
68k Ohm
56k Ohm
47k Ohm
39k Ohm
33k Ohm
27k Ohm
22k Ohm
18k Ohm
15k Ohm
12k Ohm
10k Ohm
8.2k Ohm
6.8k Ohm
5.6k Ohm
4.7k Ohm
3.9k Ohm
3.3k Ohm
2.7k Ohm
2.2k Ohm
1.8k Ohm
1.5k Ohm
1.2k Ohm
1k Ohm
390k Ohm 390k Ohm
270k Ohm 270k Ohm
220k Ohm 220k Ohm
180k Ohm 180k Ohm
150k Ohm 150k Ohm
120k Ohm 120k Ohm
100k Ohm 100k Ohm
33Hz
40Hz
48Hz
60Hz
72Hz
88Hz
82k Ohm
68k Ohm
56k Ohm
47k Ohm
39k Ohm
33k Ohm
27k Ohm
22k Ohm
18k Ohm
15k Ohm
12k Ohm
10k Ohm
8.2k Ohm
6.8k Ohm
5.6k Ohm
4.7k Ohm
3.9k Ohm
3.3k Ohm
2.7k Ohm
2.2k Ohm
1.8k Ohm
1.5k Ohm
1.2k Ohm
1k Ohm
82k Ohm
68k Ohm
56k Ohm
47k Ohm
39k Ohm
33k Ohm
27k Ohm
22k Ohm
18k Ohm
15k Ohm
12k Ohm
10k Ohm
8.2k Ohm
6.8k Ohm
5.6k Ohm
4.7k Ohm
3.9k Ohm
3.3k Ohm
2.7k Ohm
2.2k Ohm
1.8k Ohm
1.5k Ohm
1.2k Ohm
1k Ohm
106Hz
130Hz
154Hz
185Hz
220Hz
270Hz
330Hz
400Hz
480Hz
600Hz
720Hz
880Hz
1.06kHz
1.3kHz
1.54kHz
1.85kHz
2.2kHz
2.7kHz
3.3kHz
4.0kHz
4.8kHz
6.0kHz
7.2kHz
8.8kHz
10.6kHz
13.0kHz
15.4kHz
820 Ohm
680 Ohm
560 Ohm
470 Ohm
820 Ohm
680 Ohm
560 Ohm
470 Ohm
820 Ohm
680 Ohm
560 Ohm
470 Ohm
820 Ohm
680 Ohm
560 Ohm
470 Ohm
– 19 –
S P E C I F I C A T I O N S
Maximum Input Level
Input Impedance
2V RMS
20,000Ω
Maximum Output Level
Output Impedance
Frequency Response
2V RMS
500Ω
20Hz to 20kHz
+0dB –0.5dB
>105dB
Signal to Noise Ratio
Distortion
<0.02% THD + Noise
>75dB
Channel Separation
Dimensions
Punch 2X
4.8" x 2.9" x 1.8"
12.19cm x 7.37cm x 4.57cm
4.8" x 4.1" x 1.8"
Punch 3X
Punch 5X
12.19cm x 10.41cm x 4.57cm
4.8" x 5.55" x 1.8"
12.19cm x 10.41cm x 4.57cm
Factory Equipped ProCards
100Hz (2X/3X)
100Hz & 6.5kHz (5X)
12dB per octave
Butterworth
Crossover Slope
Factory Supplied Alignment
Specifications subject to change.
– 20 –
W A R R A N T Y I N F O R M A T I O N
Rockford Fosgate warrants all electronics to the original consumer/purchaser to
be free from defects in materials or workmanship for a period of three (3) years.
We will cover parts and labor provided the product was purchased from an
Authorized Rockford Fosgate Dealer. This warranty does not apply to any product
on which the seals and/or serial number have been broken, removed, tampered
with, defaced or altered in any manner. This warranty applies only to the original
consumer/purchaser and is not transferable.
Electronics found to be defective during the warranty period will be repaired or
replaced at Rockford Fosgate’s discretion. Repaired or replaced electronics will
be covered by the balance of the original warranty period only. Rockford Fosgate
shall not be responsible for any incidental or consequential damages resulting
from a defect in electronics. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the previous limitation may not be
applicable.
The warranty does not cover any appearance item, any cost or expense related to
the removal or reinstallation of the product, any accessory used in conjunction
with the product, damage to the product resulting from alteration, accident,
misuse or abuse, or improper installation. This warranty does not apply if the parts
or labor, which would otherwise be provided without charge under this warranty,
are obtained from any source other than Rockford Fosgate or an Authorized
Rockford Fosgate Service Center.
This warranty is the only express warranty and does not create any implied
warranties. Rockford Fosgate limits its obligations under any implied warranties
under state laws to a period not to exceed the written warranty period. Some states
do not allow limitation on how long an implied warranty lasts, so the above
limitation maynotapply. Thiswarrantyappliesonlyto productssold in the United
States of America or its possessions. For warranty outside the U.S.A., please
contact the nearest Authorized Rockford Fosgate Dealer. This warranty gives the
consumerspecific legalrights, and the consumermayhave otherrightswhich vary
from state to state.
A defective product must be shipped prepaid to the Authorized Rockford Fosgate
Dealer from which the consumer purchased the product or to the Rockford
Fosgate factoryin Tempe, Arizona in the originalfactorycarton orequivalent. Any
shipping loss or damage will be borne by the consumer or the consumer’s shipper.
A consumer returning a product to the factory should call (800) 669-9899 for a
Return Authorization Number. All shipments shall be clearly marked with the
Return Authorization Number on the outside of the shipping carton.
Ship to:
Rockford Corporation
Warranty Repair Department
2055 E. 5th Street
Tempe, AZ 85281 U.S.A.
Return Authorization Number:__________________________
N O TES
N O TES
Rockford Fosgate
A Division of Rockford Corporation
546 South Rockford Drive
Tempe, Arizona 85281 U.S.A.
In U.S.A. (602) 967-3565
In Canada, call Korbon (905) 567-1920
In Europe, Fax (49) 4207-801250
MAN-0628-A
1/94
|