Radio Shack PLVH7IP User Manual

7" Wide LCD Monitor  
With 4 Mounting Options  
PLVH7IP  
INSTRUCTION MANUAL  
About the liquid crystal display (LCD) panel  
1. Do not press on the LCD panel on the monitor unit as doing so can distort the picture or cause a  
malfunction, the picture may become unclear, or the LCD panel may be damaged.  
2. Notes on cleaning  
-clean the LCD panel with a slightly damp soft cloth.  
- do not use solvents such benzine, thinner, commercially available cleaners or antistatic spray.  
3. Do not use this unit temperatures under 5oC (41oF) or over 45oC (113oF).  
4. If your car was parked in a clod or hot place, the picture may not be clear. The monitor is not damaged.  
The picture will become clear after temperature in your car becomes normal.  
5.Some stationary blue or red dots may appear on the monitor.These are called bright spots, and happen  
with anyLCD.The LCD panel is highly sophisticated, and more then 99.99% of the segments used in  
the panel are flawless.However, there is a possibility that less than 0.01% of the segments are defective  
and maynot light up properly. However, these segments will not interfere with your viewing.  
Safety  
To avoid the risk of accident and the potential violation of applicable laws, the fronts tv should  
Never used while the vehicle is being driven. Also, rear displays should not be location where  
It is a visible distraction to the driver.  
In some countries the viewing of image on a display inside a vehicle even by persons other than  
The driver may be illegal. Where such regulations, they must be obeyed and this units features  
Should not be used.  
Warning  
To Prevent fire or shock hazard, do not expose the unit to  
rain or moisture.  
This symbol is intended to alert the user to  
the presence of uninsulated DANGEROUS  
VOLTAGEwithin the products enclosure  
that may be of sufficient magnitude to  
constitute a risk of electric shock to persons.  
CAUTION!!  
RISK OF ELECTRIC SHOCK  
!
DO NOT OPEN  
!
Caution: To reduce the risk of electric shock  
This symbol is intended to alert the user to  
the presence of important operating and  
Do not remove cover (or Back)  
No user-serviceable parts inside  
Refer servicing to qualified service personnel  
maintenance(servicing) instructions in the  
literature accompanying the appliance.  
Disposal of old electrical & electronic equipment  
( applicable in the European Union & other European  
countries with separate collection systems)  
This symbol on the product or on its packaging indicates that this product shall not be treated  
as household waste. In stead it shall be handed over to the applicable collection point for the  
recycling of electrical and electronic equipment. By ensuring this product is disposed of  
correctly, you will help prevent potential negative consequences for the environment and  
human health, which could otherwise be caused by inappropriate waste handling of this  
product. The recycling of materials will help to conserve natural resources. For more detailed  
information about recycling of this product, please contact your local Civic Office, your  
household waste disposal service or the shop where you purchased the product  
2
Precautions  
Please read this manual completely and carefully prior to attempt to install your new car video  
equipment. Install correctly, your new equipment will provide you with years of enjoyable and safe usage.  
Installing this unit requires technical expertise. This unit should be installed by a qualified  
technician or service personnel. If you try to install this unit by yourself, do it properly, referring to the  
installation and wiring diagrams in this operating manual. Improper installation may result in fire or  
electric shock.  
1.Do not operate this equipment while driving-safe driving should always be your highest priority.  
2.Do not install components in areas which are susceptible to rain, moisture direct sunlight, extremely  
heat or cold, excessive dust, dirt or humidity.  
3. Immediately unplug the power cord and send the monitor to your local dealer or service center as  
soon as possible:  
a) If there is smoke or any peculiar odor present during used  
b) If there is damage to any of the internal components  
4. To avoid damage to the monitor and risk of electronic shock, do not permit any of this equipment to  
become damp or wet from water or liquid. If this does occur, immediately unplug the power cord and  
send the monitor to your local dealer or service center as soon as possible.  
5. Do not attempt to repair, open or disassemble any of the components. Dangerous high voltages are  
present which may result in electric shock.  
6. Use only a power source with DC12 volts car battery (negative ground).  
7. Do not place or suspend objects on the power cord, as this may damage the cord.  
8. Do not twist or place the power cord near any source of heat in the vehicle.  
9. Do not attempt to repair a damaged, broken or faulty power cord. Replace it with a new one immediately.  
10. Avoid dropping any metal objects or inflammable items into the monitor ventilation slots.  
11. After the monitor is installed, do not arbitrarily pull it down or strike it. This may loose the mounting  
screws and cause it fall down.  
12. Do not install this unit where:  
a) it will obstruct the drivers view.  
b) it will obstruct the operation of the airbag system.  
c) it will obstruct the operation of the vehicle, especially the steering wheel, shift lever, or brake pedal.  
d) a diver or passengers may injure themselves when getting into or out of the car.  
3
Control and layout for the monitor  
MMI Input  
Front audio video input  
(Plug & Play for Ps2 or games)  
Remote Sensor  
Blue screen when  
no video signal  
Front Audio Output  
Front audio output  
Remote control IR sensor  
(headphones)  
Power On / Off  
Turn on/off the monitor  
Front A/V Input  
Front audio video input  
Menu  
Press to display MENU  
with functions and setting  
Power Cord  
(Male)  
Adjust Increase  
Adjust Decrease  
This multipurpose button  
serves to increase the selected  
parameters, such as volume,  
contrast etc.  
This multipurpose button serves  
to decrease the selected  
parameters, such as volume,  
contrast etc.  
Notice: some functions are work by remote control.  
Control and layout for the remote control  
Mute  
Power On/Off  
Turn On / Off the monitor  
Press to Mute the sound, press again  
to restore the previous volume level  
Volume Increase  
Adjust increase headphone output  
volume  
Adjust Increase  
This multipurpose button se rves to  
adjust down to se lect menu function  
and increase the selected parameters  
such as contrast, color, brightness etc  
Adjust Decrease  
This multipurpose button serves to  
adjust up to select menu function  
and decrease the selected parameters  
such as contrast, color, brightness etc.  
Volume Reduce  
Adjust reduce headphone output  
volume  
Preset  
Picture preset by factory  
Menu  
This button brings up the on-screen  
menu for adjustment of a range of  
monitor parameters such as,  
vol, con, col, bri, tint. Etc  
V1/V2  
Select Video 1 or Video 2 Input  
Invert  
To adjust the picture  
up/down/left/right  
When you use a wireless radio or portable telephone near  
this unit, picture or sound interference may occur. Do not  
use such devices near this unit.  
4
Accessories  
Universal Stand  
Headrest &  
Sun Visor Shroud  
Headrest Bag  
Remote Control  
Extension Min Din Cable  
Key-for removing the monitor  
from headrest or visor shroud  
AV Cable  
INSTRUCTION MANUAL  
Earphone  
Instruction Manual  
5
Fuse replacement  
Never use fuse with an amperage rating  
exceeding the one supplied with the unit as  
this could damage the unit.  
Connection Diagram  
When replacing the fuse, be sure to use one  
that matches the amperage described on the  
original fuse. If the fuse blows, check the  
power connection and replace the fuse. If the  
fuse blows again after replacement, there may  
be an internal malfunction. In such a case,  
consult your nearest yours dealer.  
Blue screen when  
no video signal  
1
2
Fuse  
(2A)  
Games  
BATTERY  
Video  
Player  
Replacing the Remote Control Battery  
1)Always use new battery when replace the old set.  
2)Do not attempt to charge, short-circuit, disassemble,  
heat or burn used batteries, battery may be explode  
if mistreated.  
3)Battery replacement is necessary when remote  
control acts sporadically or stops operating.  
PULL OUT  
PUSH IN  
4)Do not drop, apply shock or step on the remote control.  
5)Do not spill water on the remote control.  
6)Do not place objects between the remote control and remote sensor.  
7)Do not use remote control for the other equipments at the same time.  
8)Do not leave the remote near any heat sources, or in a place subject to direct sunlight  
(especially on the dashboard).  
9) Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately  
consult a doctor.  
10)If the MONITOR does not operate even when you operate the remote control from a close range,  
it is time to replace the battery (use CR-2025 lithium battery), refer ring to the label on the back of  
the basic control.  
11)Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur.  
6
Steps For Installing Headrest with Shroud  
Setup work  
Remove the headrest and set it in an uncluttered  
work area. Pay the appropriate precautions to  
ensure that it is not damaged during the installation.  
CAUTION: make sure the screws are not long enough to go through  
the headrest!  
If you have any doubts about this type of installation, please consult  
your local mobile electronics retailer. Cutting and making holes in  
the headrest will cause electronic damage which is expensive to repair.  
Measurements  
Press the headrest with your fingers to make  
sure there are no obstructions that would hinder  
the installation. Use paper template to mark the  
area to be cut.  
Cut the headrest  
Use an adjustable-depth blade, start  
your cut 1/4 inch inside one corner and  
cut diagonally across, stopping 1/4 inch in  
from the other corner. Repeat this procedure  
for the other two corners.  
Remove foam & obstructions  
Carefully peel off the material. Set the  
adjustable blade to one inch depth and cut  
around the edges of the hole, staying 1/4 inch  
inside the edge. Pull up one corner of the foam  
and use the blade to cut underneath. Remove  
small section at a time and ensure to be the  
uniform depth. Use a dremel or other appropriate  
tools to remove other obstructions. Insert the monitor to  
measure the fit and make adjustment if necessary  
7
Route the cable through the headrest  
Run the supplied cable through the opening  
and out to the bottom of the headrest. If possible,  
conceal the wires with a shaft covering.  
Connect the power, ground and video leads to  
test the MONITOR.  
Before connecting the monitor, pull the  
connecting cable through the headrest shroud as  
shown in diagram. Place the headrest housing into the  
opening and secure with correct fasteners.  
Install the headrest shroud  
Pull the connecting cable through the center of  
the shroud as shown in diagram, and secure the  
headrest shroud with correct fasteners  
Insert the monitor  
Push to insert the monitor  
to the headrest shroud.  
Removal  
Insert the release key between the monitor and  
headrest shroud gap and pull it out to remove the  
monitor from headrest shroud.  
8
Steps For Installing Sun-visor with Shroud  
Setup work  
Remove the visor and set it in an uncluttered  
work area. Pay appropriate precautions to  
ensure that it is not damaged during the installation.  
CAUTION: make sure the screws are not long enough to go through  
the visor!  
If you have any doubts about this type of installation, please consult  
your local mobile electronics retailer. Cutting and making holes in  
the visor will cause electronic damage which is expensive to repair.  
Measurements  
Press push on the headliner with your fingers to make  
sure there are no obstructions that would hinder  
the installation. Use paper template to mark the  
area to be cut.  
Cut the visor  
Use an adjustable-depth blade, start  
your cut 1/4 inch inside one corner and  
cut diagonally across, stopping 1/4 inch in  
from the other corner. Repeat this procedure  
for the other two corners.  
Remove foam & obstructions  
Carefully peel off the material. Set the  
adjustable blade to one inch depth and cut  
around the edges of the hole, staying 1/4 inch  
inside the edge. Pull up one corner of the foam  
and use the blade to cut underneath. Remove  
small section at a time, ensure to be the  
uniform depth . Use a dremel or other appropriate  
tools to remove other obstructions. Insert the  
monitor to measure the fit and make  
adjustment if necessary.  
9
Route the cable through the visor  
Run the supplied cable through the opening  
and out to the bottom of the visor. If possible,  
conceal the wires using a shaft covering.  
Connect the power, ground and video leads to  
test the MONITOR. Before connecting the  
monitor, pull the connecting cable assembly  
through the visor housing as shown in diagram.  
Place sun-visor shroud into the opening and  
secure it with correct fasteners.  
Install the sun-visor shroud  
Pull the connecting cable through the center of  
the housing as shown in diagram, and secure  
the sun-visor shroud with correct fasteners  
Insert the monitor  
Push to insert the monitor  
to the sun-visor shroud.  
Removal  
Insert the release key between the monitor and  
visor shroud gap and pull it out to remove the  
monitor from headrest shroud.  
Oper ate your syst em in a safe and legal manner  
When oper ate a motor vehi cle, it shoul d always be your highest priority to  
maintain safe driving habi ts.  
It is illegal in many areas of most count ries to drive with TV or MONITOR  
on, when it is visible to the driver. Please check your local and state  
laws gover ning the use of MOBILE ENTERTAINMENT SYSTEM in your area.  
10  
Steps For Installing Headrest Bag  
Insert the monitor to the headrest bag  
Put the monitor with headrest bag at the  
rear side center of pillow.  
Rear side of headrest  
Cut the magic tape to the fit your pillow size,  
then fasten it as X as diagram show.  
Front side of headrest  
11  
Function setting  
SOURCE  
Press MENU button (1)from the remote or press  
manu button (1) from the monitor to call out the  
function menu, press button (2 or 3) to the  
desired setting.  
AV1  
AV2  
AV3  
RETURN  
2
1
3
Monitor  
Remote  
SOURCE  
When screen appears SOURCEPress Menu  
button (1) to enter video signal input selection.  
[The  
symbol show current video input.]  
AV1  
AV2  
AV3  
RETURN  
2
1
3
Monitor  
Remote  
SOURCE  
Press the button( 2or3) to move the  
and choose video signal input.  
symbol  
Press menu button (1) to confirm your selection.  
Move the symbol to RETURN and press  
menu button (1) to exit input setting.  
AV1  
AV2  
AV3  
RETURN  
2
1
3
Monitor  
Remote  
12  
PICTURE  
When screen appears PICTUREpress the menu  
button (1)to enter picture parameters setting.  
BRIGHT  
CONTRAST  
COLOR  
RETURN  
2
1
3
Monitor  
Remote  
PICTURE  
Press the button( 2or3) to adjust the  
symbol  
to choose BRIGHT.  
Press menu button (1) to enter BRIGHT setting.  
[Brightness: Makes black appear darker or lighter]  
BRIGHT  
CONTRAST  
COLOR  
RETURN  
2
1
3
Monitor  
Remote  
PICTURE  
Press button 2: adjust brightness to lighter level.  
Press button 3: adjust brightness to darker level.  
Press button 1 to confirm setting.  
[Brightness adjustable level: 0~100 . Preset: 50]  
2
1
BRIGHT 50  
3
Monitor  
Remote  
13  
PICTURE  
Press the button( 2or3) to adjust the  
symbol  
to choose CONTRAST.  
Press menu button (1) to enter CONTRAST setting.  
[Contrast: Narrows or widens the gap between black & white  
(darken & brighten)]  
BRIGHT  
CONTRAST  
COLOR  
RETURN  
2
1
3
Monitor  
Remote  
PICTURE  
Press button 2: adjust contrast to brighter level.  
Press button 3: adjust contrast to darker level.  
Press button 1 to confirm setting.  
[Contrast adjustable level: 0~100 . Preset: 50]  
2
1
CONTRAST 50  
3
Monitor  
Remote  
PICTURE  
Press the button( 2or3) to adjust the  
symbol  
to choose COLOR.  
Press menu button (1) to enter hue setting.  
[COLOR: adjusts more or less color intensity]  
BRIGHT  
CONTRAST  
COLOR  
RETURN  
2
1
3
Monitor  
Remote  
14  
PICTURE  
Press button 2: adjust more color intensity level.  
Press button 3: adjust less color intensity level.  
Press button 1 to confirm setting and exit.  
[Color adjustable level: 0~100 . Preset: 50]  
2
1
COLOR 50  
3
Monitor  
Remote  
PICTURE  
Exit Picture setting, Press the button( 2or3) to  
adjust the  
symbol to RETURN.  
Press menu button (1) to exit.  
BRIGHT  
CONTRAST  
COLOR  
RETURN  
2
1
3
Monitor  
Remote  
AUDIO  
When screen appears PICTUREpress the menu  
button (1)to enter picture parameters setting.  
Press the button( 2or3) to adjust the  
symbol  
to choose VOLUME.  
Press menu button (1) to enter volume setting.  
VOLUME  
RETURN  
[VOLUME: adjust sound soft or loud ]  
2
1
3
Monitor  
Remote  
15  
AUDIO  
Press button 2: adjust sound to more loud level.  
Press button 3: adjust sound to more soft level.  
Press button 1 to confirm setting and exit.  
[Volume adjustable level: 0~100 . Preset: 50]  
2
1
VOLUME 50  
3
Monitor  
Remote  
FUNCTION  
When screen appears FUNCTIONpress the menu  
button (1)to enter function parameters setting.  
Press the button( 2or3) to adjust the  
to choose desired setting  
symbol  
INVERT 1  
SIZE:  
Full 16:9  
Language Select:  
RETURN  
2
1
3
Monitor  
Remote  
FUNCTION  
When the  
symbol at INVERT1and Press the  
MENU (1) button repeatedly to invert the picture,  
each time the button press the picture rotate as  
clockwise as the diagram show.  
Inve rt  
1
LCD  
MONITOR  
INVERT 1  
SIZE:  
Full 16:9  
Language Select:  
R O T I N O M  
D C L  
2
3 t r e v n I  
1
RETURN  
3
Monitor  
Remote  
16  
Full 16:9  
Normal 4:3  
FUNCTION  
Diagram  
Diagram  
When the  
symbol at SIZEPress the MENU (1)  
INVERT 1  
SIZE:  
button repeatedly to change the picture display  
size to Full 16:9 or Normal 4:3 as the diagram show.  
Full 16:9  
Language Select:  
RETURN  
2
1
3
Monitor  
Remote  
FUNCTION  
When the  
symbol at Language Select:Press  
the MENU (1) button to enter the OSD languages  
display.  
INVERT 1  
SIZE:  
Full 16:9  
Language Select:  
RETURN  
2
1
3
Monitor  
Remote  
FUNCTION  
Press the buttons 2 or 3 to the desired language,  
and press MENUto confirm.  
English  
German  
French  
Spanish  
Portugal  
Italian  
2
1
3
Monitor  
Chinese C  
RETURN  
Remote  
17  
FUNCTION  
Exit  
When the  
button to exit the setup.  
symbol at ExitPress the MENU (1)  
2
1
3
Monitor  
Remote  
Troubleshooting guide  
The following checklist will help you solve problems you may encounter with your unit.  
Before going through the checklist below, check the connection and operating.  
if you can not solve the problem with follows guide, please contact your nearest dealer.  
Problem  
Cause/solution  
The power cord or battery has been disconnected.  
The fuse has blown.  
No picture, no sound  
Press power on.  
Press the volume increase button on the wireless  
remote, or on the monitor.  
Press the mute button from the wireless remote.  
(TIP: refer to page 4 for the control & layout)  
Good picture, but no sound  
Dolled lines or stripes  
This maybe caused by local interference such as car  
engine or motorcycle.  
The cord has been disconnected. Connect the cord  
securely.  
Press power on.  
No picture, or no sound when you  
connect the optional equipment  
No response when pressing the buttons on  
the wireless remote  
The wireless remote batteries may be exhausted.  
18  
Specifications:  
LCD Drive Method: a-SI TFT Active Matrix  
Visible Screen Size: 7 Inch Wide Screen (Diagonal)  
Aspect Ratio: 16:9  
Display Format: 480 x RGB x 234  
Number of Pixels: 336,960  
Response Time: 15ms  
Backlight : High Brightness CCFT  
Luminance: 380 cd/m2 #3  
Backlight Life: 15,000 Hrs #1  
Contrast Ratio: 300:1  
Viewing Angle: (H/V): 120o / 100o  
Operation Temperature: -20oC ~ 70oC / -2oF ~ 158oF  
Video Color System Input: NTSC & PAL Compatible  
On Screen Display: Multi Languages  
(English, German, French, Spanish, Portugal, Italian, Chinese)  
Rear Video Input Terminals: RCA x 1 (1 Vp-p, 75 ohm)  
Front Video Input Terminals: 3.5mm Jack x1 (1 Vp-p, 75 ohm)  
Front Audio Input Terminals: 3.5mm Jack x1 (-10 dBs, 10 Kohm)  
Front Audio Output Terminals: 3.5mm Jack x1 (-10 dBs, 10 Kohm)  
Front Video Input Terminals: MMI Plug  
Front Audio Input Terminals: MMI Plug  
Remote Control: Included  
Volume / Brightness / Contrast / Color: Adjustable  
Blue Screen: Yes  
Power Input: DC12 Volts car battery (negative earth)  
Current Consumption: 6 W Max  
Weight: 340 g / 0.75 Lbs  
Size: 186 x 105 x 22.5 cm (W x H x D)  
7.32 x 4.13 x0. 88 inch (W x H x D)  
#1 A measure of the time unit screen brightness declines by half under continuous viewing  
in a car/room at 25oC with screen brightness in standard mode. (50% original brightness)  
#2 A measure of the unit temperature declines in a car/room at 25oC  
with screen brightness in standard mode. (50% original brightness)  
#3 A measure of the backlight 350cd/m2 brightness will in standard  
lamp voltage at 560 Vrms.  
Pyle, Inc.  
1600 63rd street  
Brooklyn, NY 11204  
0
6 8 8 8 8 8 8 3 5 9  
7
19  

ProMaster LED STUDIO VL306 User Manual
Philips VOIP080 User Manual
Pentax TS2V114E (C70100) User Manual
NEC NDA 31135 User Manual
Motorola Cable Box DCT3400 User Manual
KitchenAid 4KFP740CR0 User Manual
Kenwood KDV S250P User Manual
Kenwood KDC MV6521 User Manual
Kenwood EZ900HDS User Manual
Kalorik Team International Group Blender usk bl 25161 User Manual