Welcome
Thank you for purchasing the Plantronics Explorer 240, 242, 243, 245,
or 395 headset. This guide contains instructions for setting up and using
your new headset.
Please refer to the separate For Your Safety guide for important
product safety information prior to installation or use.
Getting Assistance
The Plantronics Technical Assistance Center is ready to assist you.
You can find answers to frequently asked questions, ask a question
using e-mail, receive service over the Internet, or speak directly
NOtE If you are considering returning this headset, please contact
the Technical Assistance Center first.
Registering Your Product
online so we can provide you with the best service and technical support.
NOtE For pairing your headset, your PIN code/Passkey is 0000.
ii
Package Contents and Features
NOtE Your headset may look different than the illustration, but will still
work as described.
Headset Front*
Volume Control Button
Call Control Button
Status Light
Power On/Off Switch
Swivel Earloop [fits either ear]
Headset Back
Microphone
Speaker/Eartip
Micro USB Charging Jack
Power On/Off Switch
AC Charger 100–240V
* For illustration purposes only; designs will vary by model number.
iv
Charging Your Headset
Your new headset performs best when it is fully charged. While your
headset is charging, the indicator light glows red. When your headset is
fully charged, the indicator light turns blue.
How to Charge Your Headset Using the AC Charger
1 Plug the charger into a power outlet.
2 Connect the charger cable to the headset.
1
1
C h a r g i n g t i m e
2 hours ....................... Full charge
1 hour ......................... minimum charge
before first use
2
2
NOtE Never charge the battery where the temperature may fall below
32°F (0°C) or rise above 104°F (40°C). Do not use your earpiece while it
is connected to the charger.
1
What Is Bluetooth?
Bluetooth wireless technology provides a way for devices, like headsets
and phones, to communicate with each other without wires. Pairing is
the set-up process of introducing your headset to your phone.
Before using your headset for the first time, you must pair it with
your Bluetooth-enabled phone.
Plantronics QuickPair™ Technology
To simplify the Bluetooth setup process, your new headset uses
Plantronics QuickPair technology. This process is shown on the next page.
• the first time you turn your headset on, your headset
automatically enters pairing mode for 10 minutes.
•
Until you successfully pair your headset with a Bluetooth-
enabled phone, every time you turn it on it will enter pairing mode.
• to later pair to a new phone, turn on the headset, then press
and hold the Call Control button until red then blue flashing
appears, which indicates pairing mode status.
Range (the distance between headset and phone)
• To maintain the connection, keep your headset within 33 feet
of your phone.
• For the least amount of interference place the headset and
phone on the same side of your body.
If you move too far from your phone and lose the Bluetooth connection:
•
the headset may reconnect automatically within 60 seconds when
you move closer to your phone (you will hear a low tone), OR
• you may have to tap the Call Control button to reconnect (you
will hear a low tone), OR
• if neither of the above options work, you may have to
reconnect to your headset using your phone’s Bluetooth menu.
2
Pairing Your Headset
1
2
3
SETTINGS
Time and Date
Phone Settings
BLUETOOTH
Bluetooth
Sound Settings
Network Services
Security
Discover/
BLUETOOTH
Search
Reset Settings
2XXPlantronics
PASSKEY
4
0000
How to Pair Your Phone With Your Headset for the First Time
1 turn on the Bluetooth feature on your phone.
For most phones, select Settings/Tools > Connections >
Bluetooth > On. See your phone’s user guide for more information.
2 turn the headset on.
Turn on your headset by sliding the Power Switch toward the
microphone. Wait until the indicator light flashes red then blue.
If you don’t see the red then blue flashes, turn the headset off, then
turn it on again. Press and hold the Call Control button until you see
the red then blue flashes that indicate pairing mode status.
3 Set your Bluetooth phone to ‘discover’ to locate the headset.
This usually involves going to ‘setup’, ‘connect’ or ‘Bluetooth’ menu
on your phone and selecting the option to ‘discover’ or ‘add a
device’.
4 Once available headsets are listed, select your headset (for
example 2XXPlantronics or 3XXPlantronics). If prompted for a
passkey, enter 0000.
When pairing is successful, the indicator on your headset flashes
blue. Your phone will also confirm when pairing is complete.
Call Us with Questions 1-866-363-BLUE (2583)
3
Adjusting the Fit
1
2
The headset comes out of the box with the earloop in place to wear on
your right ear.
1 Place the earloop behind your ear.
Rotate the headset so that the speaker rests comfortably in your ear.
2 Align the microphone with the corner of your mouth.
Callers can hear you best when you point the microphone towards
the corner of your mouth.
4
Adjusting the Fit
1
Right
Left
2
It’s easy to move earloop to fit on your left ear.
1 Lift the earloop.
2 Swivel the earloop to the right and push it back down.
5
Headset Controls and Indicators
Action
Indicator Light
Tone
Turn the headset On: Slide the Power Switch
On: Short blue flash
On: Four rising tones
on or off
to the “On” position.
Off: Long red flash,
Off: Four descending
Off: Slide the Power Switch
then turns off
tones
to the “Off” position.
Answer/end
a call
Tap the Call Control button.
None
None
Brief low tone at the
beginning or end of
the call.
Reject an
incoming call
Press and hold the Call
Control button until you
hear a low tone.
Low tone
Missed call
indicator
Briefly press any button to
cancel the indicator light.
Two simultaneous red/
blue flashes, a pause, then
two more red/blue flashes
(repeating for 5 minutes or
until cancelled).
None
6
Headset Controls and Indicators
Action
Indicator Light
Tone
Make a call
Battery level
Enter the number on your Blue flash every 2 seconds until
Ringing
phone and press send.
the call is ended.
To check, simultaneously
press and hold both the
Call Control and Volume
buttons for about 2
seconds. The indicator
light flashes to show the
charge level.
red flashes Battery level
None when
checking level.
1
2
3
More than 2/3 full
Low battery tone
indication: 3 tones
when under 5
minutes talk time
is remaining.
1/3 - 2/3 full
Less than 1/3 full
Adjust the volume
(during call)
Tap the Volume button to
increase through 4 levels;
tap at top level to return to
lowest volume setting.
Single blue flash for every
volume level change.
Low tone at every
volume level
change. (Two
tones at maximum
volume level.)
WARNING Do not use headsets at high volumes for an extended period of time. Doing so can cause
information on headsets and hearing.
7
Headset Controls and Indicators
Action
Indicator Light
Tone
Voice Dial
Press and hold the Call
Control button until you
hear a tone.
None
Single low tone;
phone may prompt
with “Name please” or
tones.
Redial last number Tap the Call Control
button twice.
None
None
Two brief low tones
Transfer a call from While the call is in progress,
headset to phone, press and hold the Call
Long low tone when
moving to phone; short
low tone when moving
to headset.
or from phone to
headset
Control button until you
hear a tone.
8
troubleshooting
My headset
does not work
with my phone.
Your headset may not have been in pairing mode
when your phone was searching for it. Repeat the
You may have made incorrect menu selections
on your phone while pairing. Repeat the pairing
Callers cannot hear Make sure the headset Power Switch is in the
me, or I cannot
hear callers/dialing
tone.
ON position.
Your headset may be out of Bluetooth range
or experiencing interference. Move the headset
closer to your phone, and make sure your
headset and phone are on the same side of your
Your headset battery is drained. Recharge the
battery using the supplied AC power adapter.
The listening volume is too low. Tap the Volume
button to increase the headset volume.
My headset is
flashing red then
blue
Your headset is in Pairing mode. If you are not
trying to pair the headset, reset it by simply
turning headset off then on again. Otherwise,
9
Product Specifications
Talk Time*
Standby Time*
Charge Time
Range
Up to 5 hours
Up to 7 days
2 hours
Up to 33 feet (10 meters)
Power Requirements 5V DC – 180 mA
Battery Type
Lithium ion polymer
Storage/Usage
Temperature
32º F - 104º F (0º C - 40º C)
Version
2.1 + EDR (Enhanced Data Rate)
Supports your phone’s Bluetooth Hands-free
(HFP), Headset (HSP) and Secure Simple
Pairing (SSP) profiles.
* Battery enabled. Performance may vary by device.
10
Plantronics, Inc.
345 Encinal
Santa Cruz, CA 95060
United States
Tel: 800-544-4660
© 2009 Plantronics, Inc. All rights reserved. Plantronics, the logo design, Plantronics
Explorer, QuickPair and Sound Innovation are trademarks or registered trademarks
of Plantronics, Inc. The Bluetooth name and the Bluetooth trademarks are owned by
Bluetooth SIG, Inc., and are used by Plantronics, Inc. under license. All other trademarks
are the property of their respective owners.
U.S. Patents Pending
83240-01 (12/09)
|