Digital Video Camcorder
Operating Instructions
(PV-GS15 Shown)
Models No.
PV-GS9
PV-GS12
PV-GS14
PV-GS15
Before attempting to connect, operate or adjust this product, please
read these instructions thoroughly.
Spanish Quick Use Guide is included.
Guía para rápida consulta en español está incluida.
[For PV-GS12/PV-GS14/
PV-GS15]
[For PV-GS12/PV-GS14/
PV-GS15]
LSQT0802 A
Declaration of Conformity
Trade Name :
Model No. :
Panasonic
PV-GS9/PV-GS12/PV-GS14/PV-GS15
Responsibility Party : Matsushita Electric Corporation of America
Address : One Panasonic Way Secaucus New Jersey 07094
Telephone Number : 1-800-211-PANA(7262)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
To assure continued compliance, follow the attached installation instructions and use only shielded
interface cables when connecting to computer or peripheral devices.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate this equipment.
CAUTION:
TO PREVENT FIRE OR SHOCK HAZARD AND ANNOYING
INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
CAUTION:
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.
• Since this product gets hot during use, operate it in well ventilated place; do not install this equipment in
a confined space such as a bookcase or similar unit.
WARNING
AS WITH ANY SMALL OBJECT, SD CARDS CAN BE SWALLOWED BY YOUNG CHILDREN. DO NOT
ALLOW CHILDREN TO HANDLE THE SD CARD.
U.S.A. CONSUMERS: ATTENTION:
A lithium ion/polymer battery that is
recyclable powers the product you have
purchased. Please call 1-800-8-BATTERY
for information on how to recycle this battery.
3
Important Safeguards
1. Read Instructions — All the safety and operating
instructions should be read before the unit is operated.
11. Grounding or Polarization — This video unit may be
equipped with either a polarized 2-wire AC (Alternating
Current) line plug (a plug having one blade wider than
the other) or 3-wire grounding type plug, a plug having
a third (grounding) pin.
2. Retain Instructions — The safety and operating
instructions should be retained for future reference.
3. Heed Warnings — All warnings on the unit and in the
operating instructions should be adhered to.
The 2-wire polarized plug will fit into the power outlet
only one way. This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing the
plug. If the plug still fails to fit, contact your electrician
to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
4. Follow Instructions — All operating and maintenance
instructions should be followed.
5. Cleaning — Unplug this video unit from the wall outlet
before cleaning. Do not use liquid or aerosol cleaners.
Use a dry cloth for cleaning.
The 3-wire grounding type plug will fit into a grounding
type power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding type plug.
6. Attachments — Do not use attachments not
recommended by the video product manufacturer as
they may be hazardous.
7. Water and Moisture — Do not use this video unit near
water — for example near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet basement, or near
a swimming pool, and the like.
12. Power-Cord Protection — Power-supply cords should
be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords of plugs, convenience
receptacles, and the point where they exit from the
unit.
8. Accessories — Do not place this video unit on an
unstable cart, stand, tripod, bracket, or table. The
video unit may fall, causing serious injury to a child or
adult, and serious damage to the unit. Use only with a
cart, stand, tripod, bracket, or table recommended by
the manufacturer, or sold with the video unit. Any
mounting of the unit should follow the manufacturer’s
instructions and should use a
13. Outdoor Antenna Grounding — If an outside antenna
or cable system is connected to the video unit, be sure
the antenna or cable system is grounded so as to
provide some protection against voltage surges and
built-up static charges. Part 1 of the Canadian
mounting accessory
recommended by the
manufacturer. An appliance and
cart combination should be moved
with care. Quick stops, excessive
force, and uneven surfaces may
cause the appliance and cart
combination to overturn.
Electrical Code, in USA Section 810 of the National
Electrical Code, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
9. Ventilation — Slots and openings in the cabinet are
provided for ventilation and to ensure reliable operation
of the video unit and to protect it from overheating.
These openings must not be blocked or covered.
Never place the video unit on a bed, sofa, rug, or other
similar surface, or near or over a radiator or heat
register. This video unit should not be placed in a
built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
10. Power Sources — This video unit should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of power
supply to your home, consult your appliance dealer or
local power company. For video units intended to be
operated from battery power, or other sources, refer to
the operating instructions.
14. Lightning — For added protection of this video unit
receiver during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to
the video unit due to lightning and power-line surges.
4
15. Power Lines — An outside antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken
to keep from touching such power lines or circuits as
contact with them might be fatal.
b. If any liquid has been spilled into, or objects have
fallen onto, the video unit.
c. If the video unit has been exposed to rain or water.
d. If the video unit does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician to
restore the video unit to its normal operation.
16. Overloading — Do not overload wall outlets and
extension cords as this can result in a risk of fire or
electric shock.
17. Objects and Liquids — Never push objects of any kind
into this video unit through openings as they may touch
dangerous voltage points or short out parts that could
result in a fire or electric shock. Never spill liquid of any
kind onto the video unit.
e. If the video unit has been dropped or the cabinet
has been damaged.
f. When the video unit exhibits a distinct change in
performance — this indicates a need for service.
20. Replacement Parts — When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock or other hazards.
18. Servicing — Do not attempt to service this video unit
yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
19. Damage Requiring Service — Unplug this video unit
from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
21. Safety Check— Upon completion of any service or
repairs to this video unit, ask the service technician to
perform safety checks to determine that the video unit
is in safe operating order.
a. When the power-supply cord or plug is damaged.
Precautions
WARNING
USE & LOCATION
• TO AVOID SHOCK HAZARD ... Your Camcorder and power supply should not be exposed to rain or moisture. Do not
connect the power supply or operate your Camcorder if it gets wet. Your Camcorder has been designed for outdoor
use, however, it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or direct splashing
from a pool or even a cup of coffee. This action could permanently damage the internal parts of your Camcorder. Do not
attempt to disassemble this unit. There are no user serviceable parts inside. Unplug your Camcorder from the power
supply before cleaning.
CAUTION
• DO NOT AIM YOUR CAMCORDER AT THE SUN OR OTHER BRIGHT OBJECTS
• DO NOT LEAVE THE CAMCORDER WITH THE EVF AIMED DIRECTLY AT THE SUN AS THIS MAY CAUSE
DAMAGE TO THE INTERNAL PARTS OF THE EVF
• DO NOT EXPOSE YOUR CAMCORDER TO EXTENDED HIGH TEMPERATURE ... Such as, direct sunlight, inside a
closed car, next to a heater, etc... This action could permanently damage the internal parts of your Camcorder.
• AVOID SUDDEN CHANGES IN TEMPERATURE ... If the unit is suddenly moved from a cold place to a warm place,
moisture may form on the tape and inside the unit.
• DO NOT LEAVE YOUR CAMCORDER OR THE POWER SUPPLY TURNED ON WHEN NOT IN USE.
• STORAGE OF YOUR CAMCORDER ... Store and handle your Camcorder in a manner that will not subject it to
unnecessary movement (avoid shaking and striking). Your Camcorder contains a sensitive pick-up device which could
be damaged by improper handling or storage.
CARE
• TO CLEAN YOUR CAMCORDER ... Do not use strong or abrasive detergents when cleaning your Camcorder body.
• TO PROTECT THE LENS ... Do not touch the surface of the lens with your hand. Use a commercial Camcorder lens
solution and lens paper when cleaning the lens. Improper cleaning can scratch the lens coating.
• TO PROTECT THE FINISH OF YOUR CAMCORDER ... Before handling your Camcorder, make sure your hands and
face are free from any chemical products, such as suntan lotion, as it may damage the finish.
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited viewing.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
5
Before opening the CD-ROM package (PV-GS15: Supplied, PV-GS9/PV-GS12/PV-GS14: Optional
Software), please read the following.
End User License Agreement (for USB Driver, WebCam Driver and
DV STUDIO (Optional Software))
You (“Licensee”) are granted a license for the Software defined in this End User Software Agreement
(“Agreement”) on condition that you agree to the terms and conditions of this Agreement. If Licensee does
not agree to the terms and conditions of this Agreement, promptly return the Software to Matsushita
Electric Industrial Co., Ltd. (“Matsushita”), its distributors or dealers from which you made the purchase.
Article 1
License
Licensee is granted the right to use the software, including the information recorded or described on the
CD-ROM, instruction manuals, and any other media provided to Licensee (collectively “Software”), but all
applicable rights to patents, copyrights, trademarks and trade secrets in the Software are not transferred to
Licensee.
Article 2
Use by a Third Party
Licensee may not use, copy, modify, transfer or allow any third party, whether free of charge or not, to use,
copy or modify the Software, except as expressly provided for in this Agreement.
Article 3
Restrictions on Copying the Software
Licensee may make a single copy of the Software in whole or in part solely for back-up purpose.
Article 4
Computer
Licensee may only use the Software on a single computer at a single location.
Article 5 Reverse Engineering, Decompiling or Disassembly
Licensee may not reverse engineer, decompile, or disassemble the Software, except to the extent either of
them is permitted under law or regulation of the country where Licensee resides. Matsushita, or its
distributors or dealers will not be responsible for any defects in the Software or damage to Licensee
caused by Licensee’s reverse engineering, decompiling, or disassembly of the Software.
Article 6
Limitation of Liability
The Software is provided “AS-IS” without warranty of any kind, either expressed or implied, including, but
not limited to, warranties of non-infringement, merchantability and/or fitness for a particular purpose.
Further, Matsushita does not warrant that the operation of the Software will be uninterrupted or error free.
Matsushita or any of its distributors or dealers will not be liable for any damage suffered by Licensee
arising from or in connection with Licensee’s use of the Software.
Article 7
Export Control
Licensee agrees not to export or re-export to any country the Software in any form without the appropriate
export licenses under regulations of the country where Licensee resides, if necessary.
Article 8
Termination of License
The right granted to Licensee hereunder will be automatically terminated if Licensee violates any of the
terms and conditions of this Agreement. Upon such automatic termination, Licensee must destroy the
Software and related documentation together with all the copies thereof at Licensee’s own expense.
6
This operating instruction book is designed for use with models PV-GS9, PV-GS12, PV-GS14, and
PV-GS15. The PV-GS15 is the model used for illustrative purposes. Features may vary, so please read
carefully.
Differences between models
Model
Number
PV-GS9
PV-GS12
PV-GS14
PV-GS15
Battery Pack
(Supplied)
CGR-D08R
(800 mAh)
CGR-D08R
(800 mAh)
CGR-D08R
(800 mAh)
CGR-D14
(1 350 mAh)
Memory
Card
Supplied
(RP-SD008MMK0)
Optional
Optional Software
Optional
Optional
Optional Software
Optional
CD-ROM
Optional Software
Optional
Supplied (LSFT0575)
Remote
Control
Supplied (LSSQ0411)
Supplied
(K1HA05CD0005)
USB Cable
Optional
Optional
Optional
f2.1-42 mm, F1.8-3.1
(35 mm equivalent:
39.5-790 mm),
f2.1-42 mm, F1.8-3.1 f2.1-46.2 mm, F1.8-3.4 f2.1-50.4 mm, F1.8-3.6
(35 mm equivalent:
39.5-790 mm),
20x zoom lens
(35 mm equivalent:
39.5-869 mm),
22x zoom lens
(35 mm equivalent:
39.5-948 mm),
24x zoom lens
Lens
20x zoom lens
Photoshot
(Tape)
Yes
No
No
No
Feature
(Tape Recording Mode) (Tape Recording Mode) (Tape Recording Mode)
(Tape Playback Mode) (Tape Playback Mode) (Tape Playback Mode)
(Card Recording Mode) (Card Recording Mode) (Card Recording Mode)
(Tape Recording Mode)
(Tape Playback Mode)
Mode Dial
(Picture Playback
Mode)
(Picture Playback
Mode)
(Picture Playback
Mode)
Card
Feature
No
Yes
Yes
Yes
Liquid Crystal Color
Electronic Viewfinder
Liquid Crystal Color
Electronic Viewfinder
Viewfinder
Electronic Viewfinder
Electronic Viewfinder
LED Video
Light
No
No
No
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
S-Video
Output Jack
Microphone
Jack
7
Contents
Before Use
Recording Mode
Things You Should Know ....................................2
Safety Precautions ..............................................2
Important Safeguards..........................................4
Precautions .........................................................5
End User License Agreement..............................6
Differences between models ...............................7
Quick Guide.......................................................10
Standard Accessories........................................12
Controls and Components.................................12
The Remote Control (PV-GS15 Only) ...............14
Power Supply ....................................................15
Charging Time and Available Recording Time...16
How to remove the Sensor tag..........................16
The Grip Belt .....................................................16
Re-attaching the Lens Cap................................17
Attaching the Shoulder Strap ............................17
Inserting a Cassette ..........................................17
Using a Memory Card
About Recording................................................24
Recording on a Tape .........................................24
Recording a Still Picture on a Tape
(PV-GS9 Only).................................................25
Recording a Still Picture on a Card (Photoshot)
(For PV-GS12/PV-GS14/PV-GS15).................25
Recording Yourself ............................................26
Recording with the Built-in LED Video Light
(For PV-GS12/PV-GS14/PV-GS15).................26
Quick Start.........................................................26
Self-timer Recording..........................................27
Zoom In/Out Functions......................................27
Digital Zoom Function .......................................27
Image Stabilizer Function..................................28
Fade In/Out Functions.......................................28
Backlight Compensation Function.....................29
MagicPix Function.............................................29
Soft-Skin Mode..................................................29
Wind Noise Reduction Function........................29
Cinema Function ...............................................29
Recording in Special Situations.........................30
Recording in Natural Colors ..............................30
Adjusting White Balance Manually....................31
Manual Shutter Speed Adjustment....................32
Manual Iris Adjustment......................................32
Manual Focus Adjustment.................................32
Digital Effect Functions......................................33
(For PV-GS12/PV-GS14/PV-GS15).................18
Turning on the Camcorder.................................18
Easy to Use Mode Dial......................................18
Using the Viewfinder/LCD Monitor ....................19
Using the Menu Screen.....................................19
List of Menus.....................................................20
Setting Date and Time.......................................23
Internal Lithium Battery Recharge.....................23
LP Mode ............................................................23
Audio Recording Mode......................................23
8
Playback Mode
Playing Back a Tape..........................................35
Finding a Scene You Want to Play Back ...........35
Slow Motion Playback (Remote Control Only) ..36
Still Playback/Still Advance Playback................36
Index Search Functions
With a PC
Using the Software with a Personal Computer..47
Using USB Driver ..............................................47
To disconnect USB cable safely........................49
Using as a Web Camera ...................................50
Using the DV STUDIO 3.1E-SE
(Remote Control Only) ....................................37
Playback Zoom Function
(Optional Software) .........................................53
Using the ArcSoft Software
(Remote Control Only) ....................................37
Playback Digital Effect Functions ......................38
Playing Back a Memory Card
(For PV-GS12/PV-GS14/PV-GS15).................38
Slide Show
(PV-GS15: Supplied).......................................55
If you no longer need software or driver
(Uninstall) ........................................................56
Notes.................................................................57
(For PV-GS12/PV-GS14/PV-GS15).................39
Creating a Title
(For PV-GS12/PV-GS14/PV-GS15).................40
Adding a Title
(For PV-GS12/PV-GS14/PV-GS15).................40
Writing Printing Data on a Card
(For PV-GS12/PV-GS14/PV-GS15).................41
Protecting the Files on a Card
Others
Indications .........................................................59
Initializing the Modes.........................................60
Warning/Alarm Indications.................................60
Notes and Hints.................................................61
Cautions for Use................................................65
Before Requesting Service
(For PV-GS12/PV-GS14/PV-GS15).................41
Deleting the Files Recorded on a Card
(For PV-GS12/PV-GS14/PV-GS15).................42
Formatting a Card
(For PV-GS12/PV-GS14/PV-GS15).................42
Playing Back on Your TV...................................43
(Problems and Solutions)................................69
Using the RESET button ...................................70
Explanation of Terms.........................................71
Specifications ....................................................72
Camcorder Accessory System ..........................73
Camcorder Accessory Order Form....................74
Request for Service Notice................................75
Limited Warranty ...............................................76
Customer Services Directory.............................78
Spanish Quick Use Guide/
Editing Mode
Recording from a Tape onto a Card
(For PV-GS12/PV-GS14/PV-GS15).................44
Recording Pictures from a Card onto a Tape
(For PV-GS12/PV-GS14/PV-GS15).................44
Audio Dubbing (Remote Control Only)..............44
Copying on an S-VHS (or a VHS) Cassette......45
Using the DV Cable for Recording ....................45
PC Connection With DV Interface Cable...........46
Guía Para Uso Rápido ....................................79
Guía rápida........................................................80
Index..................................................................82
9
Before Use
Inserting a Card
Quick Guide
(For PV-GS12/PV-GS14/PV-GS15)
1 Place your Thumb on the [OPEN▼] 1 Knob
and pull the LCD Monitor 2 out in the
direction of the arrow.
1 Attach the Battery to the AC Adaptor and
charge it.
2
1
• Before use, fully charge the Battery.
• Since the Battery will not be charged when the DC
Cable is connected to the AC Adaptor, disconnect
it from the AC Adaptor.
• The [POWER] Lamp and [CHARGE] Lamp light
up, and charging starts.
2 Slide the [OPEN] Lever 3 to open the Card
Slot Cover 4 .
3 While holding the Memory Card with its cut
corner facing right 5 insert it into the Card
Slot 6 .
• When the [CHARGE] Lamp goes off, charging is
completed.
4 Close the Card Slot Cover 4 securely.
3
2 Attach the charged Battery to the Camcorder.
4
6
5
Recording on a Tape
1 Set the [OFF/ON] Switch 1 to [ON].
• The [POWER] Lamp 2 lights up.
Inserting a Cassette
1 Slide the [OPEN/EJECT] Lever 1 toward the
front and pull down to fully open the Cassette
Compartment Cover.
1
• To protect the tape, if the cover is not fully opened,
the cassette cannot be ejected.
2
2 Insert a Cassette.
2 Set the Mode Dial to Tape Recording Mode.
1
(PV-GS9)
(PV-GS12/
PV-GS14/
PV-GS15)
3 Close the Cassette Holder by pressing the
[PUSH] mark 2 .
3 Press the Recording Start/Stop Button.
• Recording starts.
4 Close the Cassette Compartment Cover by
pressing the mark 3 .
2
3
4 Press the Recording Start/Stop Button again
to pause the recording.
10
Before Use
2 Set the Mode Dial to Tape Playback Mode.
Recording a Still Picture on Tape
(PV-GS9 Only)
1 Set the Mode Dial to Tape Recording Mode.
(PV-GS9)
(PV-GS12/
PV-GS14/
PV-GS15)
3 Press the [
] Button to rewind the tape.
2 Press the [PHOTO SHOT] Button in the
Recording Pause Mode.
4 Press the [►] Button to start playback.
Recording a Still Picture on Card
(Photoshot)
(For PV-GS12/PV-GS14/PV-GS15)
5 Press the [ ] Button to stop playback.
1 Set the Mode Dial to Card Recording Mode.
Playing Back a Card
(For PV-GS12/PV-GS14/PV-GS15)
2 Press the [PHOTO SHOT] Button.
1 Set the Mode Dial to Picture Playback Mode.
Playing Back a Tape
1 Set the [OFF/ON] Switch 1 to [ON].
• The [POWER] Lamp 2 lights up.
2 Start Playback.
► :
Starting the Slide Show
Playing back the next picture
Playing back the previous picture
Stop the Slide Show
:
:
1
2
:
:
Pause the Slide Show
11
Before Use
Controls and Components
Before Use
Camcorder
Standard Accessories
6
Illustrated are accessories supplied with the
Camcorder.
7
8
9
2
21
20
1)
19
10
11
12
18
13 14 15 16 17
PV-DAC11
LSJA0288
K2CB2CB00014
1
2)
3)
CR2025
3
4
5
CGR-D08R
(For PV-GS9/
(PV-GS15 Only) PV-GS12/PV-GS14)
1
2
LCD Monitor Open Knob [OPEN▼] (p. 19)
LCD Monitor (pp. 19, 68)
CGR-D14
LSSQ0411
(PV-GS15 Only)
4)
5)
6)
Due to limitations in LCD production technology,
there may be some tiny bright or dark spots on
the LCD Monitor screen.
However, this is not a malfunction and does not
affect the recorded picture.
RP-SD008MMK0
(PV-GS15 Only)
LSJA0280
LSFC0018
7)
3
4
5
Card Slot Cover Open Lever [◄OPEN]
(For PV-GS12/PV-GS14/PV-GS15) (p. 18)
Card Slot (For PV-GS12/PV-GS14/PV-GS15)
(p. 18)
Card Slot Cover (For PV-GS12/PV-GS14/
PV-GS15) (p. 18)
K1HA05CD0005
(PV-GS15 Only)
LSFT0575
(PV-GS15 Only)
1) AC Adaptor, DC Cable and AC Cable
(p. 15)
6
7
Speaker (p. 35)
Recording Check Button [
] (p. 24)
CAUTION:
Recording Button [REC] (p. 46)
This unit will operate on 110/120/220/240 V AC.
An AC plug adaptor may be required for
voltages other than 120 V AC. Please contact
either a local or foreign electrical parts distributor
for assistance in selecting an alternate AC plug.
We recommend using the accessory power plug
adaptor (VJSS0070/KZDB4ZE00001) in an area
which has special AC outlets.
8
9
MagicPix Button [MAGICPIX] (p. 29)
Soft Skin Button [SOFT SKIN] (p. 29)
Backlight Button [BACK LIGHT] (p. 29)
Light Button [LIGHT]
(For PV-GS12/PV-GS14/PV-GS15) (p. 26)
Card Access Lamp
(For PV-GS12/PV-GS14/PV-GS15) (p. 18)
Pause Button [ ] (p. 25)
Still Button [STILL] (p. 25)
10
11
12
13
2) Battery Pack (p. 15)
3) Remote Control and Button-Type Battery
(p. 14) (PV-GS15 Only)
4) AV Cable (pp. 43, 45)
14
15
Fast Forward/Cue Button [
Play Button [►] (p. 35)
Enter Button [ENTER] (p. 20)
Stop Button [ ] (p. 35)
Fade Button [FADE] (pp. 28-29)
Rewind/Review Button [
Mode Selector Switch
] (p. 35)
5) Shoulder Strap (p. 17)
16
6) SD Memory Card (PV-GS15 Only) (p. 18)
7) USB Connection Kit (USB Cable and
CD-ROM) (PV-GS15 Only) (pp. 47-49, 51, 54)
17
18
] (p. 35)
[AUTO/MANUAL/FOCUS] (pp. 24, 30-32)
Menu Button [MENU] (p. 19)
Multi Button [MULTI] (p. 33)
19
20
Picture-in-Picture Button [P-IN-P] (p. 34)
21
Reset Button [RESET] (pp. 60, 70)
12
Before Use
26
34 35 36
37
40
42
22
23
24
41
38
39
43
44
25
22
23
24
25
Lens Hood (p. 69)
Lens
Microphone (built-in, stereo) (pp. 27, 29)
Built-in LED Light
(For PV-GS12/PV-GS14/PV-GS15) (p. 26)
34
Viewfinder (pp. 19, 68)
Due to limitations in LCD production technology,
there may be some tiny bright or dark spots on
the Viewfinder screen.
However, this is not a malfunction and does not
affect the recorded picture.
26
Zoom Lever [W/T] (pp. 27-28, 35)
27
28
35
Eyepiece Corrector Knob (p. 19)
36
Photoshot Button [PHOTO SHOT]
(pp. 25-26)
37
38
39
Cassette Eject Lever [OPEN/EJECT] (p. 17)
DC Input Jack [DC IN] (p. 15)
S-Video Output Jack [S-VIDEO OUT]
(For PV-GS14/PV-GS15) (pp. 43, 45)
31
29 30
40
41
42
Mode Dial (p. 18)
Power Lamp [POWER] (p. 18)
Quick Start Recording Button [QUICK
START] (p. 26)
Quick Start Recording Lamp (p. 26)
32 33
27
28
29
30
Cassette Holder
Cassette Compartment Cover (p. 17)
] (pp. 48-49, 51, 54)
DV Input/Output Terminal (pp. 45-46)
USB Jack [
43
44
Recording Start/Stop Button (p. 24)
Power Switch [OFF/ON] (pp. 18, 24)
• Connect this to the digital video equipment.
31
32
White Balance Sensor (p. 31)
Remote Control Sensor (p. 15)
Audio-Video Output Jack [AV OUT]
(pp. 43, 45)
45 46
Headphone Jack [PHONES]
• Connecting an AV Cable to this jack activates
the Camcorder’s built-in speaker, but
connecting a headphone, etc. deactivates it.
• When connecting the pin plug of the AV Cable
to this jack, plug it in as far as it goes.
• When using headphones, set [INITIAL] >> [AV
JACK] >> [OUT/PHONES].
47 48
49
45
46
47
48
Shoulder Strap Holders (p. 17)
Grip Belt (p. 16)
Battery Holder
Battery Eject Switch [BATTERY RELEASE]
(p. 16)
Tripod Receptacle
33
Microphone Jack [MIC]
(For PV-GS14/PV-GS15)
• When connecting an external microphone
or audio equipment to this jack, the built-in
microphone does not operate.
• A compatible plug-in powered microphone can
be used. Please consult your dealer for more
information.
49
• Used for mounting the Camcorder on an
optional tripod.
• The microphone may make noises depending
on the type used. In this case, we recommend
using the battery with the Camcorder to reduce
noises instead of the AC Adaptor.
13
Before Use
The following buttons function in the same manner as
the corresponding buttons on the Camcorder.
Remote Control (PV-GS15 Only)
Using the wireless Remote Control with the
Camcorder, most of the Camcorder functions can
be operated from a distance.
65
66
71
72
50
51
67
68
69
70
73
54
55
52
53
74
75
56
65
Photoshot Button [PHOTO SHOT]
(pp. 25-26)
50
51
52
53
54
55
56
66
67
Date/Time Button [DATE/TIME] (p. 60)
Indication Output Button [OSD] (p. 43)
Display Button [DISPLAY] (p. 60)
Reset Button [RESET] (pp. 60, 70)
Recording Button [ REC] (p. 45)
Audio Dubbing Button [A.DUB] (p. 44)
Title Button [TITLE] (p. 40)
Multi-Picture/Picture-in-Picture Button
[MULTI/P-IN-P] (pp. 33-34)
Rewind/Review Button [
Pause Button [ ] (pp. 36, 44-45)
Stop Button [ ] (pp. 37, 45)
68
69
70
71
] (p. 35)
Recording Start/Stop Button [START/STOP]
(p. 24)
Cursor buttons for Variable Speed Search
Function [▲, ▼] (p. 36)
72
73
74
75
Direction Buttons for Playback Zoom
Function [▲, ▼, ◄, ►] (p. 37)
Play Button [►] (pp. 36, 45)
Fast Forward/Cue Button [
Playback Zoom Button [P.B. ZOOM] (p. 37)
Enter Button [ENTER] (p. 20)
] (p. 35)
The Remote Control (PV-GS15 Only)
62
Inserting the Button-type Battery
Before using the Remote Control, insert the supplied
button-type battery.
57
58
59
60
61
63
64
1 While pressing the Lock Button 1 , pull out
the Battery Holder. Then, remove the
button-type battery.
57
58
Slow Motion/Still Advance Buttons [
: reverse, : forward) (p. 36)
Index Search Buttons [
: reverse, : forward) (p. 37)
,
]
(
1
,
]
2 Insert the button-type battery with the (+)
marking facing upward.
(
59
60
61
62
Selection Button [SELECT] (p. 38)
Store Button [STORE] (p. 38)
Off/On Button [OFF/ON] (p. 38)
Zoom/Volume Button [ZOOM/VOL]
(p. 38)
Variable Speed Search Button
[VAR.SEARCH] (p. 36)
Menu Button [MENU] (p. 19)
3 Insert the Battery Holder into the Remote
Control.
63
64
14
Before Use
• When the button-type battery is exhausted, replace
Setup on the Remote Control:
it with a new CR2025 battery. (A battery is normally
expected to last about 1 year. However, it depends
on operation frequency.)
2
1
• Make sure to match the poles correctly when
inserting the button-type battery.
[VCR1]:
Press the [ ] Button and [ ] Button
WARNING
simultaneously.
1
●Replace Battery with Panasonic or Lixing
type CR2025 only. Use of another battery
may present a risk of fire or explosion.
●Battery may explode if mistreated.
●As with any small object, this type of Battery
can be swallowed by young children. Do not
allow children to handle this Battery.
[VCR2]:
Press the [ ] Button and [ ] Button
simultaneously.
• When the battery in the Remote Control is replaced,
the mode is automatically reset to [VCR1] Mode.
2
Power Supply
Using the AC Adaptor
CAUTION
●Dispose of used battery promptly.
●Do not recharge, disassemble or dispose of
in fire.
Using the Remote Control
(PV-GS15 Only)
1 Direct the Remote Control at the Remote
31
Control Sensor
of the Camcorder and
1 Connect the DC Cable to the Camcorder.
2 Connect the DC Cable to the AC Adaptor.
press an appropriate button.
3 Connect the AC Cable to the AC Adaptor and
the AC Jack.
• Before connecting or disconnecting the power
15°
15°
44
supply, set the [OFF/ON] Switch
on the
31
Camcorder to [OFF] and make sure that
[POWER] Lamp is not lit. (p. 18)
15°
15°
• Distance from the Camcorder: Within
approximately 15 feet (5 meters)
• Angle: Within approximately 15° in the vertical and
horizontal directions from the central axis
Using the Battery
Before use, fully charge the Battery.
• We recommend using a Panasonic Battery.
• We cannot guarantee the quality of this Camcorder
when batteries from other companies are used.
• The above operating ranges are for indoor use
Outdoors or under strong light, the Camcorder may
not operate properly even within the above ranges.
1 Attach the Battery to the AC Adaptor and
charge it.
Selecting Remote Control Modes
When 2 Camcorders are used simultaneously, they
can be operated individually by selecting different
Remote Control Modes.
• If the Remote Control Mode of the Camcorder and
that of the Remote Control do not match, [CHECK
REMOTE MODE (REMOTE)] Indication is displayed.
Setup on the Camcorder:
Set [REMOTE] on the [INITIAL] Sub-Menu to the
desired Remote Control Mode. (p. 21)
15
Before Use
• Since the Battery will not be charged when the DC
Cable is connected to the AC Adaptor, disconnect
it from the AC Adaptor.
• The [POWER] Lamp and [CHARGE] Lamp light
up, and charging starts.
• The times shown in the table are for continuous
recording at a temperature of 68 °F (25 °C) and
humidity of 60 %. If the Battery is charged at a
higher or lower temperature, the charging time
may be longer.
• When the [CHARGE] Lamp goes off, charging is
completed.
• The available recording time becomes shorter
if you use both of Viewfinder and LCD Monitor
simultaneously when rotating the LCD Monitor
forward to record yourself or setting [EVF
ON/AUTO] to [ON].
• When the battery is completely discharged, the
[CHARGE] Lamp blinks at first, but the battery is
charged normally. When the temperature of the
battery is too high or low, the [CHARGE] Lamp
blinks and the charging time becomes longer than
usual.
How to remove the Sensor tag
1 Detach the end of the Grip Belt.
2 Attach the charged Battery to the Camcorder.
2 Remove the Sensor tag. Then, replace the
Grip Belt.
Disconnecting the Power Source
44
Set the [OFF/ON] Switch
sliding the [BATTERY RELEASE] Switch
remove the Battery downward or DC Cable.
to [OFF], and while
48
,
• When attaching or removing Battery, set the [OFF/ON]
Switch to [OFF] and make sure the [POWER] Lamp
is not lit.
The Grip Belt
44
To Use as a Grip Belt
Adjust the length of the Grip Belt to the size of your
hand.
48
1 Detach the end of the Grip Belt.
• For other notes concerning this item, see page 61.
Charging Time and Available
Recording Time
2 Adjust the length of the Grip Belt to the size
of your hand.
A
B
A
B
1 h
CGR-D08R
CGR-D14
2 h 10 min. (1 h 45 min.)
1 h 30 min.
3 h (2 h 25 min.)
A Charging Time
Maximum Continuous Recording Time
B
3 Reattach the Grip Belt.
• “1 h 30 min.” indicates 1 hour and 30 minutes.
• Battery CGR-D08R (PV-GS9/PV-GS12/PV-GS14)
or CGR-D14 (PV-GS15) is supplied.
• The times shown in the table are approximate
times. The numbers indicate the recording time
when the Viewfinder is used. The numbers in
parentheses indicate the recording time when the
LCD Monitor is used. In actual use, the available
recording time may be shorter.
16
Before Use
• Pull it out more than 1 inch (2 cm) 1 from the
Shoulder Strap Length Adjuster so that it cannot
slip off.
Re-attaching the Lens Cap
To protect the Lens surface, attach the Lens Cap.
• The Lens Cap and Lens Cap Cord come preattached
to the Grip Belt.
1
• Attach the other end of the Shoulder Strap to the
other Shoulder Strap Holder in the same way.
1 Pass one end of the Lens Cap Cord through
the attached eye on the Lens Cap. Then pass
the Lens Cap through the loop made by itself
and pull tight.
Inserting a Cassette
37
1 Slide the [OPEN/EJECT] Lever
toward the
front and pull down to fully open the Cassette
Compartment Cover.
• To protect the tape, if the cover is not fully opened,
the cassette cannot be ejected.
37
• When not using the Lens Cap, pull the Lens Cap
Cord in the direction of the arrow. 1
• When you are not recording, be sure to cover the
Lens with the Lens Cap for protection. 2
2 Insert a Cassette.
2
3 Close the Cassette Holder by pressing the
[PUSH] mark 1 .
1
• When you remove the Lens Cap, press the knobs
1
firmly.
4 Close the Cassette Compartment Cover by
pressing the mark 2 .
Attaching the Shoulder Strap
2
We recommend that you attach the Shoulder Strap
before going out to avoid dropping the Camcorder.
1 Pull the end of the Shoulder Strap through
the Shoulder Strap Holder on the Camcorder.
Accidental Erasure Prevention
Opening the accidental erasure prevention slider 1
on the cassette (by sliding it to the [SAVE] arrow
direction) prevents recording. To enable recording,
close the accidental erasure prevention slider (by
sliding it to the [REC] arrow direction).
1
2 Fold the end of the Shoulder Strap, run it
through the Shoulder Strap Length Adjuster,
and pull it.
• For other notes concerning this item, see page 61.
17
Before Use
Using a Memory Card (For PV-GS12/
Turning on the Camcorder
PV-GS14/PV-GS15)
Turn on the power first and then select modes.
How to Turn on the Power
A Card can be used to record still pictures.
• Use a genuine SD Memory Card or MultiMediaCard
manufactured by Panasonic only.
Before inserting or removing a Card, be sure to
turn off the Camcorder.
44
1 Set the [OFF/ON] Switch
to [ON] while
pressing the button 1 .
41
• The [POWER] Lamp
lights up.
• Otherwise, the Camcorder may not function properly
or it may cause the loss of recorded data in a Card.
44
1
Inserting a Card
3
1 Slide the [OPEN] Lever
to open the Card
41
5
Slot Cover
.
5
How to Turn off the Power
3
44
2 Set the [OFF/ON] Switch
pressing the button 1 .
to [OFF] while
2 While holding the Memory Card with its cut
corner facing right 1 , insert it into the Card
44
1
4
Slot
.
Easy to Use Mode Dial
4
You can choose a desired mode by rotating the Mode
Dial.
1
40
1 Rotate the Mode Dial
.
5
3 Close the Card Slot Cover
securely.
Removing the Card
Open the Card Slot Cover and press the center of
the Card and then pull it straight out.
40
• After removing the Card, close the Card Slot Cover.
• The Camcorder may be damaged if the Card is
forced out when the Card is fully inserted.
(PV-GS12/PV-GS14/
PV-GS15)
(PV-GS9)
12
Card Access Lamp
Tape Recording Mode
:
Use this mode when recording pictures on a
tape. Also, you can record still pictures on the
card simultaneously while recording on a tape
(For PV-GS12/PV-GS14/PV-GS15).
12
While the Camcorder is accessing the Card (reading,
recording, playback or erasing), the Card Access
Lamp lights up.
• While the Card Access Lamp is on, never attempt
to open the Card Slot Cover, to pull out the Card,
to turn off the Camcorder, or to turn the Mode Dial.
Such actions will damage the Card, and recorded
data, and cause the Camcorder to malfunction.
Tape Playback Mode
Use this mode when playing back the
recorded scene on a tape.
:
:
Card Recording Mode
(For PV-GS12/PV-GS14/PV-GS15)
Use this mode when recording still pictures
on a card.
Picture Playback Mode
:
(For PV-GS12/PV-GS14/PV-GS15)
Use this mode when playing back the
recorded still picture on a card.
PC Mode
:
(For PV-GS12/PV-GS14/PV-GS15)
Use this mode when you want to connect the
Camcorder to your Personal Computer.
18
Before Use
Using the Viewfinder/LCD Monitor
Using the Viewfinder
Before using the Viewfinder, adjust the field of view so
that the displays inside the Viewfinder become clear
and easy to read.
1 Pull the Viewfinder.
1 180°
2 90°
Closing the LCD Monitor
Push the LCD Monitor until it is securely locked.
• Make sure the Card Slot Cover is closed.
2 Adjust by turning the Eyepiece Corrector
Adjusting Brightness and Color Level
When [LCD/EVF SET] on the [LCD/EVF] Sub-Menu
is set to [YES], the following items are displayed.
35
Knob
.
35
To Use the Viewfinder at the Same Time as the
LCD Monitor
Set [LCD/EVF] >> [EVF ON/AUTO] >> [ON].
• The Viewfinder does not turn off even if the LCD
Monitor is opened.
• When you turn the Camcorder off, this setting is
canceled.
LCD Brightness [LCD BRIGHTNESS]
Adjusts the brightness of the image on the LCD
screen.
LCD Color Level [LCD COLOR LEVEL]
Adjusts the color saturation of the image on the LCD
screen.
Using the LCD Monitor
With the LCD Monitor open, you can also record the
picture while watching it.
Brightness of the Viewfinder
[EVF BRIGHTNESS]
Adjusts the brightness of the image in the Viewfinder.
1
1 Place your Thumb on the [OPEN▼] Knob
To Adjust
2
and pull the LCD Monitor
direction of the arrow.
out in the
Press the [
adjusted, and then press the [
/
] Button and select the item to be
] Button to
/
• The Viewfinder is now deactivated.
raise or lower the number of vertical bars in the Bar
• The LCD Monitor can be opened a maximum
of 120°. If you open the LCD Monitor by 120°, it
becomes convenient to operate menus or to play
back pictures.
Indication.
• More vertical bars indicates stronger brightness or
color saturation.
• For other notes concerning this item, see page 68.
2
Using the Menu Screen
To facilitate the selection of a desired function or
setup, this Camcorder displays various function setups
on Menus.
1
• When operating the menu with the Viewfinder, set
[LCD/EVF] >> [EVF ON/AUTO] >> [ON] or rotate the
LCD Monitor by 180°.
2 Adjust the LCD Monitor angle according to
the desired recording angle.
• The LCD Monitor can rotate a maximum of 180°
1 from the vertical position upwards and a
maximum of 90° 2 to the downward direction.
Forcefully rotating the LCD Monitor beyond these
ranges will damage the Camcorder.
19
1 Press the [MENU] Button
.
19
13 14 15 16 17
19
Before Use
• The Menu corresponding to the Mode selected by
40
15
to confirm the
2 Press the [ENTER] Button
selection of the file.
using the Mode Dial
is displayed.
• After the above File Selection Procedure, carry
out the various Menu Operations. (The above
procedure will not be repeated in the following
instructions.)
40
(PV-GS9)
(PV-GS12/
PV-GS14/
PV-GS15)
List of Menus
The figures of the Menus are for explanation purposes
only, and they are different from the actual Menus.
13 16
to select a
2 Press the [
desired Sub-Menu.
• Press the [
item.
/
] Button
[TAPE RECORDING MENU]
Tape Recording Menu
/
] Button to display the highlighted
(PV-GS12/PV-GS14/PV-GS15)
(PV-GS9)
14
3 Press the [
] Button
to display the
selected Sub-Menu.
4 Press the [
/
] Button to select the item.
14
5 Press the [
] Button
to display the
selected item.
6 Press the [
and press the [ENTER]
determine the setting.
• While a Menu is displayed, you cannot record or play
back. Menus can be displayed during playback but
not during recording. The above operations can be
done using the [MENU] Button, [▲▼◄►] Buttons
and [ENTER] Button on the Remote Control. (p. 14)
/
] to select the desired mode
1) [CAMERA]
Camera Setup Sub-Menu
[PROG.AE]
Auto Exposure Mode (p. 30)
[EIS]
Image Stabilizer (p. 28)
[D.ZOOM]
15
Button to
Digital Zoom (p. 27)
[SHTR EFFECT] (PV-GS9 Only)
Shutter effect (p. 25)
[SELF TIMER]
Self-timer Recording (p. 27)
[USB FUNCTION]
USB Functions Mode (pp. 51, 54)
To Return to the Previous Screen
17
Press the [
] Button
.
To Exit the Menu Screen
Press the [MENU] Button again.
About the Menu Mode Setting
The setting selected on the Menu will be retained
even when the Camcorder is turned off. However,
if the Battery or AC Adaptor is disconnected before
turning off the Camcorder, the selected setup may
not be retained.
• If you press the [
back to the previous screen.
2) [DIGITAL]
Digital Setup Sub-Menu
[EFFECT1]
Digital Effects 1 (p. 33)
[EFFECT2]
] Button, the menu changes
• Menu operation flow is shown in this text by >>.
Digital Effects 2 (p. 33)
[MULTI MODE]
Multi-Picture Mode (p. 33)
[TITLE IN] (For PV-GS12/PV-GS14/PV-GS15)
Adding a Title (p. 40)
3) [CARD] (For PV-GS12/PV-GS14/PV-GS15)
Card Setup Sub-Menu
[PICT QUALITY]
File Selection in the Picture Playback
Mode (For PV-GS12/PV-GS14/PV-GS15)
A File Selection Operation may be necessary during
Menu Operations. In this case, carry out the following
procedure.
1 Press the [
/
/
/
] Button and select
a file.
Picture Quality (p. 25)
• The selected file is marked by a frame.
[CREATE TITLE]
Title Creation (p. 40)
4) [RECORDING]
Recording Setup Sub-Menu
[REC SPEED]
Recording Speed Mode (p. 23)
[AUDIO REC]
Audio Recording Mode (p. 23)
20
Before Use
[SCENE INDEX]
Scene Index Mode (p. 37)
[WIND CUT]
[TAPE PLAYBACK MENU]
Tape Playback Menu
(PV-GS12/PV-GS14/PV-GS15)
(PV-GS9)
Wind Noise Reduction (p. 29)
[ZOOM MIC]
Zoom Microphone (p. 27)
[CINEMA]
Cinema-like Format Recording (p. 29)
5) [DISPLAY]
Display Setup Sub-Menu
[DISPLAY]
Display Mode (p. 60)
[DATE/TIME]
Date and Time Indication (p. 60)
1) [PLAYBACK]
Playback Functions Sub-Menu
[SEARCH]
Index Search Mode (p. 37)
[12bit AUDIO]
Audio Selector (p. 44)
[AUDIO OUT]
[C.DISPLAY]
Counter Display Mode (p. 60)
[C.RESET]
Audio Output Mode (p. 64)
Counter Reset (p. 71)
[USB FUNCTION]
USB Functions Mode (pp. 51, 54)
2) [DIGITAL]
Playback Digital Setup Sub-Menu
[EFFECT ON]
Digital Effect On/Off (p. 38)
• It resets the counter to zero. However, it cannot reset
the Time Code.
6) [LCD/EVF]
LCD/EVF Setup Sub-Menu
[LCD/EVF SET]
LCD and Viewfinder Adjustment (p. 19)
[EFFECT SEL]
Digital Effect Selection (p. 38)
[TITLE IN] (For PV-GS12/PV-GS14/PV-GS15)
Adding a Title (p. 40)
[SELF REC]
Recording Yourself (p. 26)
[EVF ON/AUTO]
Using the Viewfinder (p. 19)
3) [CARD] (For PV-GS12/PV-GS14/PV-GS15)
Card Setup Sub-Menu
[PICT QUALITY]
7) [INITIAL]
Initial Setup Sub-Menu
[BLANK SEARCH]
Blank Search (p. 24)
Picture Quality (p. 25)
[CREATE TITLE]
Title Creation (p. 40)
[DEMO MODE]
Demonstration Mode
4) [RECORDING]
Recording Setup Sub-Menu
[REC SPEED]
Recording Speed Mode (p. 23)
[AUDIO REC]
Audio Recording Mode (p. 23)
5) [DISPLAY]
Display Setup Sub-Menu
[DISPLAY]
Display Mode (p. 60)
[DATE/TIME]
• If no operation takes place for approximately 10
minutes after the AC Adaptor is connected to the
Camcorder and the [OFF/ON] Switch is turned to
[ON] without inserting a Cassette or a Card, the
Camcorder is automatically set to Demonstration
Mode for introducing its functions. If any button is
pressed or operated, the Demonstration Mode is
canceled. The Demonstration Mode can be started
by setting [DEMO MODE] to [ON] and by exiting the
Menu. To terminate the Demonstration Mode, insert
a Cassette or set the [DEMO MODE] to [OFF].
[AV JACK]
Date and Time Indication (p. 60)
[C.DISPLAY]
AV Jack (pp. 13, 65)
Counter Display Mode (p. 60)
[C.RESET]
Counter Reset (p. 71)
[REMOTE]
Remote Control Mode (p. 15)
[BEEP SOUND]
Beep Sound (p. 61)
6) [LCD/EVF]
LCD/EVF Setup Sub-Menu
[LCD/EVF SET]
[CLOCK SET]
Date and Time Setting (p. 23)
LCD and Viewfinder Adjustment (p. 19)
[EVF ON/AUTO]
Using the Viewfinder (p. 19)
[INITIAL SET]
Initial Setting Mode (p. 60)
21
Before Use
7) [INITIAL]
6) [INITIAL]
Initial Setup Sub-Menu
[BLANK SEARCH]
Blank Search (p. 24)
[AV JACK]
AV Jack (pp. 13, 65)
[REMOTE]
Initial Setup Sub-Menu
[AV JACK]
AV Jack (pp. 13, 65)
[REMOTE]
Remote Control Mode (p. 15)
[BEEP SOUND]
Remote Control Mode (p. 15)
[BEEP SOUND]
Beep Sound (p. 61)
Beep Sound (p. 61)
[CLOCK SET]
Date and Time Setting (p. 23)
[INITIAL SET]
Initial Setting Mode (p. 60)
[CARD RECORDING MENU]
(For PV-GS12/PV-GS14/PV-GS15)
Card Recording Menu
[PICTURE PLAYBACK MENU]
(For PV-GS12/PV-GS14/PV-GS15)
Picture Playback Menu
1) [CAMERA]
Camera Setup Sub-Menu
[PROG.AE]
Auto Exposure Mode (p. 30)
[SHTR EFFECT]
Shutter Effect (p. 25)
[SELF TIMER]
Self-timer Recording (p. 27)
2) [DIGITAL]
Digital Setup Sub-Menu
[TITLE IN]
Adding a Title (p. 40)
3) [CARD]
Card Setup Sub-Menu
[PICT QUALITY]
Picture Quality (p. 25)
[CREATE TITLE]
Title Creation (p. 40)
[BURST MODE]
RapidFire Consecutive Photoshot (p. 26)
4) [DISPLAY]
Display Setup Sub-Menu
[DISPLAY]
Display Mode (p. 60)
[DATE/TIME]
Date and Time Indication (p. 60)
5) [LCD/EVF]
LCD/EVF Setup Sub-Menu
[LCD/EVF SET]
LCD and Viewfinder Adjustment (p. 19)
[SELF REC]
Recording Yourself (p. 26)
[EVF ON/AUTO]
1) [DELETE]
Deleting a File Sub-Menu
[FILE BY SEL]
Selecting and Deleting a File (p. 42)
[ALL FILES]
Deleting All Files (p. 42)
[TITLE BY SEL]
Selecting and Deleting a Title (p. 42)
2) [EDITING]
Editing a File Sub-Menu
[FILE LOCK]
Setting the Lock (p. 41)
[DPOF SET]
Setting DPOF (p. 41)
[CARD FORMAT]
Formatting a Card (p. 42)
3) [DIGITAL]
Playback Digital Setup Sub-Menu
[TITLE IN]
Adding a Title (p. 40)
4) [DISPLAY]
Display Setup Sub-Menu
[DISPLAY]
Display Mode (p. 60)
[DATE/TIME]
Date and Time Indication (p. 60)
[C.DISPLAY]
Counter Display Mode (p. 60)
[C.RESET]
Counter Reset (p. 71)
Using the Viewfinder (p. 19)
22
Before Use
5) [LCD/EVF]
LCD/EVF Setup Sub-Menu
[LCD/EVF SET]
LCD and Viewfinder Adjustment (p. 19)
[EVF ON/AUTO]
Internal Lithium Battery Recharge
The internal lithium battery sustains the operation of
the clock. When the [ ] Indication flashes, the
internal lithium battery is near exhaustion.
Using the Viewfinder (p. 19)
6) [INITIAL]
Initial Setup Sub-Menu
[AV JACK]
AV Jack (pp. 13, 65)
[REMOTE]
Remote Control Mode (p. 15)
1 Connect the AC Adaptor to the Camcorder
with the power turned off and then connect
to the AC jack.
Setting Date and Time
Since the internal clock of the Camcorder has a slight
imprecision make sure to check the time before
recording.
19
13 14 16 17
• After charging for 4 hours, the built-in lithium battery
can power the clock for approximately 3 months.
1 Set [INITIAL] >> [CLOCK SET] >> [YES].
LP Mode
A desired recording speed can be selected with [REC
SPEED] on the [RECORDING] Sub-Menu.
If LP Mode is selected, the recording time
becomes 1.5 times longer than that of SP Mode.
Although the image quality does not decrease with the
LP Mode recording, mosaic-pattern noise may appear
on a playback image, or some normal functions may
be restricted.
13 16
to select [YEAR],
[MONTH], [DAY], [HOUR] or [MIN.] and press
2 Press the [
/
] Button
14 17
to set it to the desired
the [
/
]
value.
• The contents that are recorded in LP Mode are not
completely compatible with other equipment.
• Audio dubbing is not possible with LP Mode. (p. 44)
• Year will cycle in the order shown below.
2000, 2001, ..., 2089, 2000, ...
19
3 Press the [MENU] Button
the date and time.
to finish setting
• The clock operation starts from [00] second.
Audio Recording Mode
• If the built-in battery is weak, the [ ] Indication
flashes. In this case, charge the built-in battery.
• The clock uses the 12-hour system.
The sound quality of the recorded sound can be
selected with [AUDIO REC] on the [RECORDING]
Sub-Menu.
High sound-quality recording is possible with “16 bit
48 kHz 2 track” Mode. With the “12 bit 32 kHz 4 track”
Mode, the original sound can be recorded on 2 tracks
in stereo, while the other 2 tracks can be used for
Audio Dubbing.
23
Recording Mode
43
3 Press the Recording Start/Stop Button
• Recording starts.
• After [RECORD] is displayed, it changes to [REC].
.
Recording Mode
About Recording
When recording pictures on a tape, set the Mode
40
Dial
to Tape Recording Mode [
].
When recording still pictures on a card, set the
40
Mode Dial
PV-GS12/PV-GS14/PV-GS15).
When recording with the [AUTO/MANUAL/FOCUS]
to Card Recording Mode [
] (For
43
43
4 Press the Recording Start/Stop Button
again to pause the recording.
• The [PAUSE] Indication is displayed.
18
Switch
set to [AUTO], the Camcorder
automatically adjusts the focus and white balance.
In some cases, they cannot be adjusted
automatically and need to be adjusted manually.
(pp. 31, 32)
18
Recording “Simultaneous Motion/Still
Record Mode”
(For PV-GS12/PV-GS14/PV-GS15)
Even if the Mode Dial is set to Tape Recording
Mode and the recording to a tape is in progress,
you can also record a still picture on a card by
pressing the [PHOTO SHOT] Button.
• Before turning on the power, remove the Lens
Cap. If the Lens Cap is still attached when the
power is turned on, Automatic White Balance
Adjustment (p. 30) may not function correctly.
• When the Recording Pause Mode continues for more
than 5 minutes, the power is turned off automatically
for tape protection and power conservation. (If the
AC Adaptor is used, the power is turned off only
when the tape is inserted in Tape Recording Mode.)
When the tape is inserted in Tape Recording Mode
and if the Recording Pause Mode continues for more
than 5 minutes the power is turned off automatically.
To resume recording from this condition, turn off,
then turn on the power again.
To Check the Recording
By pressing the [ ] Button
7
briefly in the
Recording Pause Mode, you can play back the last
few seconds of the recorded scene.
7
• The [CHK] Indication is displayed. After checking,
the Camcorder resumes the Recording Pause Mode.
• When the Camcorder is connected to a personal
computer with a USB Cable, Standby mode is not
available.
• For other notes concerning this item, see page 61.
Finding the End of Recording
(Blank Search Function)
The Blank Search Function aids you in locating the
Recording on a Tape
1 Set the [OFF/ON] Switch
44
to [ON].
41
• The [POWER] Lamp
lights up.
end of the recording on the Cassette quickly.
1 Set [TAPE RECORDING MENU] or [TAPE
PLAYBACK MENU] >> [INITIAL] >> [BLANK
SEARCH] >> [YES].
44
41
19
40
2 Set the Mode Dial
Mode.
to Tape Recording
13 14 15 16 17
• The [BLANK] Indication appears during the Blank
Search.
40
• Approximately 1 second before the last recorded
scene, the Camcorder switches to the Recording
Pause Mode or the Still Playback Mode.
• If there is no blank left on the Cassette, the
Camcorder stops at the end of the tape.
(PV-GS9)
(PV-GS12/
PV-GS14/
PV-GS15)
24
Recording Mode
To Cancel Blank Search Before Completion
Press the [ ] Button.
Recording a Still Picture on a Card
(Photoshot) (For PV-GS12/PV-GS14/
PV-GS15 )
Still pictures can be recorded on the Memory Card
from the Camcorder.
Digital Still Picture
When the [STILL] Button
13
is pressed, images
become still pictures. When the button is pressed
again, the Digital Still Picture Mode is canceled.
40
1 Set the Mode Dial
Mode.
to Card Recording
13
40
• We recommend that you press the [STILL] Button
first at the position where you wish to record the still
picture so as to enter the Digital Still Picture Mode
and then press the [PHOTO SHOT] Button.
36
2 Press the [PHOTO SHOT] Button
.
36
Progressive Photoshot
P
When the [
] Indication is displayed, Progressive
Photoshot Function works. You can record still pictures
with higher quality by using this function.
• The Progressive Photoshot Function may not be
activated depending on the function you use. (p. 60)
• To record still pictures with higher quality, we
recommend setting to the Card Recording Mode.
(To activate the Progressive Photoshot Function
regardless of the function you use)
PICTURE
• The [
] Indication lights up in red.
Selecting the quality of Photoshot images
1 Set [CARD RECORDING MENU] >> [CARD]
>> [PICT QUALITY] >> a desired image
quality.
• When you record onto the tape and the card
simultaneously, the Progressive Photoshot Function
is not activated.
19
13 14 15 16 17
Recording a Still Picture on a Tape
(PV-GS9 Only)
Still pictures can be recorded from the Camcorder
lens.
Maximum number of images recordable on the
supplied (PV-GS15 Only) Card (8MB)
[FINE] (high image quality):
36
1 Press the [PHOTO SHOT] Button
Recording Pause Mode.
in the
approximately 45 pictures
[NORMAL] (normal image quality):
approximately 95 pictures
[ECONOMY] (low image quality):
approximately 190 pictures
36
• These figures vary depending on the subject being
photographed.
Maximum number of still pictures recordable
on an SD Memory card (optional)
Continuous Photoshot
PICTURE
QUALITY
If you set [SHTR EFFECT] on the [CAMERA]
Sub-Menu to [ON] and keep the [PHOTO SHOT]
Button pressed, the Camcorder will continuously
record still pictures in approximately 0.7 seconds
intervals until the button is released.
FINE
NORMAL
ECONOMY
16 MB
100
220
200
440
400
880
32 MB
64 MB
440
880
1 760
3 520
7 040
14 080
• The screen blinks and, at the same time, a shutter
clicking sound is recorded.
128 MB
256 MB
512 MB
880
1 760
3 520
7 040
1 760
3 520
• These figures vary depending on the subject being
photographed.
25
Recording Mode
RapidFire Consecutive Photoshot
The still pictures can be recorded on a Card at regular
intervals.
Recording with the Built-in LED Video
Light (For PV-GS12/PV-GS14/PV-GS15)
To brighten the natural colors in a scene. Gain Up
mode works with the Built-in Video Light to enhance
the light’s brightness.
1 Set [CARD RECORDING MENU] >> [CARD]
>> [BURST MODE] >> [ON].
11
1 Press the [LIGHT] Button
. 1
19
13 14 15 16 17
11
• The [
] Indication appears.
• The Built-in LED Video Light lights and the Gain
Up mode is set to on.
• Gain Up mode will be brighter than when only
the Video Light is on, however, ghost images will
appear.
36
2 Press the [PHOTO SHOT] Button
.
2 Press the [LIGHT] Button. 2
• Gain Up mode is set to off.
• To eliminate ghost images, use this mode.
36
3 Press the [LIGHT] Button. 3
• The Video Light turns off.
• Pressing the [LIGHT] Button again returns to 1 .
1
2
3
• When [ON] is selected, the still pictures can be
recorded in approximately 0.5 second intervals until
the [PHOTO SHOT] Button is released or 10 pictures
are recorded.
• For other notes concerning this item, see pages
61-62.
• For other notes concerning this item, see page 62.
Recording Yourself
By opening the LCD Monitor and rotating it forward (to
the lens side), you can let the subject in front of the
Camcorder monitor the shot while recording is in
progress.
Quick Start
42
By pressing the [QUICK START] Button
, the
Camcorder will be ready for recording in approximately
1.3 seconds after it is turned on.
42
1 Press the [QUICK START] Button
.
42
• The Quick Start Recording Lamp
lights up.
• When the LCD Monitor is opened, the Viewfinder
is disabled automatically. However, when the LCD
Monitor is rotated forward, the image is also shown
in the Viewfinder.
42
• If you prefer to have the image on the LCD Monitor
to look like an image in a mirror, set [SELF REC]
on the [LCD/EVF] Sub-Menu to [MIRROR]. Images
are recorded normally and no left and right reversal
occurs.
44
2 Set the [OFF/ON] Switch
to [OFF].
• The Quick Start Recording Lamp remains lit.
44
26
Recording Mode
44
• Zoom Magnification Indication is displayed for a few
3 Set the [OFF/ON] Switch
to [ON].
seconds.
• The Camcorder will be ready for recording in
approximately 1.3 seconds.
To Cancel the Quick Start
Keep the [QUICK START] Button pressed for
approximately 2 seconds and make sure the Quick
Start Recording Lamp is not lit.
• For other notes concerning this item, see page 62.
To Take Close-up Shots of Small
Subjects
(Macro Close-up Function)
When the zoom magnification is 1X, the Camcorder
can focus on a subject that is as close as
approximately 0.8 inches (20 mm) from the Lens.
Small subjects like insects can be recorded with
this function.
Self-timer Recording
When you set the self-timer, the recording starts
automatically after 10 seconds on the Tape (PV-GS9
Only) or the Card (For PV-GS12/PV-GS14/PV-GS15).
1 Set [TAPE RECORDING MENU] (PV-GS9
Only) or [CARD RECORDING MENU] (For
PV-GS12/PV-GS14/PV-GS15) >> [CAMERA] >>
[SELF TIMER] >> [ON].
To Use the Zoom Microphone Function
Along with the zooming operation, the microphone’s
directional angle and sensitivity are varied for
recording sounds.
19
13 14 15 16 17
• Set [TAPE RECORDING MENU] >>
[RECORDING] >> [ZOOM MIC] >> [ON]. (The
[Z.MIC] Indication is displayed.)
• The [ ] Indication appears.
36
2 Press the [PHOTO SHOT] Button
.
36
• For other notes concerning this item, see page 62.
• The [ ] Indication flashes and the recording
starts after 10 seconds.
• You can also use the RapidFire Consecutive
Photoshot (For PV-GS12/PV-GS14/PV-GS15).
(p. 26)
Digital Zoom Function
This function is useful when you want to record
close-up shots of subjects located beyond a normal
zoom range of 1X to 20X (PV-GS9/PV-GS12)/22X
(PV-GS14)/24X (PV-GS15) magnification. With the
Digital Zoom Function, you can select a magnification
from 50X up to 800X.
• For other notes concerning this item, see page 62.
Zoom In/Out Functions
1 Set [TAPE RECORDING MENU] >> [CAMERA]
>> [D.ZOOM] >> [50X] or [800X].
This feature gives special effects to the picture by
recording objects close by or with wide-angle shot.
1 For wide-angle shots (zoom out):
19
26
Push the [W/T] Lever
For close-ups (zoom in):
towards [W].
13 14 15 16 17
Push the [W/T] Lever towards [T].
• 50X : Digital zooming to 50X
• 800X : Digital zooming to 800X
26
27
Recording Mode
26
2 Push the [W/T] Lever
towards [W] or
Fade In/Out Functions
towards [T] to zoom in or out.
Fade In
Fade In brings out images and sounds gradually from
a black screen at the beginning of a scene.
26
To Cancel the Digital Zoom Function
Set [TAPE RECORDING MENU] >> [CAMERA] >>
[D.ZOOM] >> [OFF].
16
1 Keep pressing the [FADE] Button
the Recording Pause Mode.
during
• For other notes concerning this item, see page 62.
Image Stabilizer Function
If the Camcorder is shaken while recording, the
camera shake in the image can be corrected.
• If the Camcorder shakes too much, the images may
not be stabilized.
16
• The image fades out gradually.
1 Set [TAPE RECORDING MENU] >> [CAMERA]
>> [EIS] >> [ON].
2 When the image is completely gone, press
43
the Recording Start/Stop Button
recording.
to start
19
13 14 15 16 17
• The [EIS] Indication appears.
43
16
3 Release the [FADE] Button
about 3
seconds after recording starts.
• The image reappears gradually.
Fade Out
43
2 Press the Recording Start/Stop Button
or
Fade Out causes images and sounds to disappear
gradually, leaving a black screen at the end of a scene.
36
[PHOTO SHOT] Button
to start recording.
36
43
To Cancel Image Stabilizer Function
Set [TAPE RECORDING MENU] >> [CAMERA] >>
[EIS] >> [OFF].
16
1 Keep pressing the [FADE] Button
recording.
while
• For other notes concerning this item, see page 62.
16
• The image fades out gradually.
28
Recording Mode
2 When the image is completely gone, press
Soft-Skin Mode
43
the Recording Start/Stop Button
recording.
to stop
This enables you to record skin colors in a softer tone.
In order to get the best result, avoid background colors
similar to the skin color of the subject. Otherwise, this
may result in a softer background lacking in detail.
9
1 Press the [SOFT SKIN] Button
.
43
9
16
3 Release the [FADE] Button
.
• The still picture cannot fade in or fade out.
• The [
] Indication appears.
SOFT SKIN
Backlight Compensation Function
This prevents the subject from being recorded too
darkly when backlit. (Backlight is the light that shines
from behind the subject being recorded.)
• To obtain the best effect, we recommend to take a
bust shot, so that the upper part from the breast of
the subject can be framed in the screen.
To Cancel the Soft-Skin Mode
10
1 Press the [BACK LIGHT] Button
.
Press the [SOFT SKIN] Button.
10
Wind Noise Reduction Function
This function reduces the sound of wind hitting the
microphone when recording.
• The [
] Indication flashes and then is displayed.
• The entire screen becomes brighter.
1 Set [TAPE RECORDING MENU] >>
[RECORDING] >> [WIND CUT] >> [ON].
To Resume Normal Recording
19
Press the [BACK LIGHT] Button.
13 14 15 16 17
• For other notes concerning this item, see page 62.
• The [WIND CUT] Indication appears.
MagicPix Function
This function allows you to record color images brightly
in a dark place without using the Video Flash.
8
1 Press the [MAGICPIX] Button
.
To Cancel the Wind Noise Reduction Function
Set [TAPE RECORDING MENU] >> [RECORDING]
>> [WIND CUT] >> [OFF].
8
• For other notes concerning this item, see page 63.
Cinema Function
• The [MAGICPIX] Indication appears.
This function is for recording a cinema-like image.
1 Set [TAPE RECORDING MENU] >>
[RECORDING] >> [CINEMA] >> [ON].
To Cancel the MagicPix Function
Press the [MAGICPIX] Button again.
19
• For other notes concerning this item, see pages
62-63.
13 14 15 16 17
29
Recording Mode
• Black bars appear at the top and bottom of the
1) [
] Sports Mode
screen.
• For recording scenes involving quick movements,
such as sports scenes.
2) [
] Portrait Mode
• Use when you want to make people (subjects)
stand out from the background.
3) [ ] Low Light Mode
To Cancel the Cinema Function
Set [TAPE RECORDING MENU] >> [RECORDING]
>> [CINEMA] >> [OFF].
• For brightening a dark scene.
4) [
] Spotlight Mode
• For recording a subject under a spotlight.
5) [
] Surf & Snow Mode
• For other notes concerning this item, see page 63.
• For recording in glaring surroundings, such as ski
slopes, beaches, etc.
Recording in Special Situations
To Cancel the Program AE Function
Set the [PROG.AE] on the [CAMERA] Sub-menu
to [OFF]. Or, set the [AUTO/MANUAL/FOCUS]
Switch to [AUTO].
(Program AE)
You can select optimal automatic exposure under
specific recording situations.
18
1 Set the [AUTO/MANUAL/FOCUS] Switch
to [MANUAL].
• For other notes concerning this item, see page 63.
Recording in Natural Colors
18
(White Balance)
Depending on the scene or lighting conditions, the
Automatic White Balance Adjustment Mode may not
be able to bring out natural colors. In this case, the
white balance can be adjusted manually.
When the Camcorder is turned on with the Lens Cap
on, the Automatic White Balance Adjustment may not
function properly. Please turn on the Camcorder after
removing the Lens Cap.
• The [MNL] Indication appears.
2 Set [TAPE RECORDING MENU] or [CARD
RECORDING MENU] (For PV-GS12/PV-GS14/
PV-GS15) >> [CAMERA] >> [PROG.AE] >> a
desired mode ([
]).
], [
], [ ], [
] or
18
1 Set the [AUTO/MANUAL/FOCUS] Switch
to [MANUAL].
[
18
19
13 14 15 16 17
• The Indication of the selected Mode appears.
• The [MNL] Indication appears.
15
2 Press the [ENTER] Button
.
1)
2)
3)
5)
4)
14 15 17
• The [AWB] Indication appears.
14
3 Press the [
] Button
or [
] Button
17
to select a desired White Balance Mode.
1)
2)
3)
4)
30
Recording Mode
1) Automatic White Balance Adjustment [AWB]
2) The white balance setting that was previously
About White Balance Sensor
31
The White Balance Sensor
determines the
set manually [
]
nature of the light source during recording.
3) Outdoor Mode [
]
4) Indoor Mode (recording under incandescent
lamp) [
To Resume Automatic Adjustment
]
14
17
] Button
Press the [
] Button
or [
31
until the [AWB] Indication appears. Or, set the
[AUTO/MANUAL/FOCUS] Switch to [AUTO].
• Do not cover the White Balance Sensor with your
hand during recording because White Balance will
not function normally.
Adjusting White Balance Manually
White Balance Adjustment recognizes the color of light
and adjusts so that white will appear pure white. The
Camcorder determines the hue of light that comes
through the Lens and White Balance Sensor, thereby
judging the recording condition, and selects the closest
hue setting. This function is called Automatic White
Balance Adjustment.
For light outside the functional Auto White Balance
Adjustment range, use the Manual White Balance
Adjustment Mode.
18
1 Set the [AUTO/MANUAL/FOCUS] Switch
to [MANUAL].
18
• The [MNL] Indication appears.
15
2 Press the [ENTER] Button
.
Outside of the effective range of Automatic White
Balance Adjustment, the image will become reddish or
bluish. Even within the effective range of Automatic
White Balance Adjustment, the Automatic White
Balance Adjustment may not function properly if there
is more than one light source. In this case, adjust the
White Balance.
14 15 17
• The [AWB] Indication appears.
1)
The effective range of Automatic White Balance
Adjustment on this Camcorder
14
3 Press the [
] Button
or [
] Button
2)
3)
4)
5)
6)
7)
8)
9)
10)
17
Blue sky
until the [
] Indication is displayed.
Cloudy sky (rain)
TV screen
Sunlight
White fluorescent lamp
Halogen light bulb
Incandescent light bulb
Sunrise or sunset
Candlelight
4 Point the Camcorder at a full-screen white
subject.
15
5 Keep pressing [ENTER] Button
] Indication stops flashing.
until the
[
To Resume Automatic Adjustment
• For other notes concerning this item, see page 63.
14
17
Press the [
] Button
or [
] Button
until the [AWB] Indication is displayed. Or, set the
[AUTO/MANUAL/FOCUS] Switch to [AUTO].
31
Recording Mode
14
3 Press the [
] Button
to adjust the iris.
Range of Iris Adjustment
CLOSE (Closed), F16, ..., F2.0,
OP (Opened) + 0dB, ..., OP + 18dB
or [
] Button
Manual Shutter Speed Adjustment
17
Useful for recording fast-moving subjects.
18
1 Set the [AUTO/MANUAL/FOCUS] Switch
to [MANUAL].
When a value closer to [CLOSE] is selected, the
image becomes darker.
When a value closer to [OP + 18dB] is selected, the
image becomes brighter.
18
The value to which + dB is attached indicates a
Gain-up value. If this value is too large, the quality of
the image deteriorates.
• The [MNL] Indication appears.
15
2 Press the [ENTER] Button
until the
To Resume Automatic Adjustment
Shutter Speed Indication appears.
Set the [AUTO/MANUAL/FOCUS] Switch to [AUTO].
• For other notes concerning this item, see page 63.
Manual Focus Adjustment
Focus can be adjusted manually for recording in a
situation where auto focus may not function well.
14 15 17
18
1 Set the [AUTO/MANUAL/FOCUS] Switch
to [MANUAL].
14
3 Press the [
] Button
or [
] Button
17
to adjust the shutter speed.
Range of Shutter Speed Adjustment
1/60–1/8000 s in Tape Recording Mode
1/60–1/500 s in Card Recording Mode
(For PV-GS12/PV-GS14/PV-GS15)
The standard shutter speed is 1/60 s.
18
Selecting a speed closer to [1/8000] causes the
shutter speed to be faster.
• The [MNL] Indication appears.
18
2 Slide the [AUTO/MANUAL/FOCUS] Switch
to [FOCUS].
To Resume Automatic Adjustment
Set the [AUTO/MANUAL/FOCUS] Switch to [AUTO].
• For other notes concerning this item, see page 63.
18
Manual Iris Adjustment
(F Number)
• The [►MF] Indication (Manual Focus Mode)
appears.
You can use this function when the screen is too bright
or too dark.
18
1 Set the [AUTO/MANUAL/FOCUS] Switch
to [MANUAL].
14
3 Press the [
] Button
or [
] Button
18
17
to adjust the focus.
14
17
• The [MNL] Indication appears.
15
2 Press the [ENTER] Button
Indication appears.
until the Iris
14
or
• If you keep pressing the [
] Button
[
] Button, the speed of adjusting becomes
faster.
To Resume Automatic Adjustment
Set the [AUTO/MANUAL/FOCUS] Switch to [AUTO]
or [FOCUS].
14 15 17
32
Recording Mode
To Select a Desired Digital Effect
Digital Effect Functions
This Camcorder is equipped with Digital Effect
Functions that add special effects to the scene.
Digital Effects 1 [EFFECT1]
Set [TAPE RECORDING MENU] >> [DIGITAL] >>
[EFFECT1] or [EFFECT2] >> a desired Digital
Effect.
1) MULTI
2) P-IN-P
3) WIPE
To Cancel the Digital Effect
Set [TAPE RECORDING MENU] >> [DIGITAL] >>
[EFFECT1] or [EFFECT2] >> [OFF].
4) MIX
5) STROBE
6) TRAIL
• For other notes concerning this item, see pages
63-64.
Multi-Picture Mode
Strobe Multi-Picture Mode:
7) MOSAIC
10) SLIM
8) MIRROR 9) STRETCH
1) Multi Mode [MULTI]
2) Picture-In-Picture Mode [P-IN-P]
3) Wipe Mode [WIPE]
You can capture and record 9 consecutive small still
pictures.
Manual Multi-Picture Mode:
4) Mix Mode [MIX]
5) Strobe Mode [STROBE]
• Records images with a stroboscopic effect.
6) Trailing Effect Mode [TRAIL]
• Records images with a trailing effect.
7) Mosaic Mode [MOSAIC]
• Produces a mosaic-like image.
You can manually capture and record 9 small still
pictures.
1 Set [TAPE RECORDING MENU] >> [DIGITAL]
>> [EFFECT1] >> [MULTI].
8) Mirror Mode [MIRROR]
• The right half of an image becomes a mirror
image of the left half.
9) Stretch Mode [STRETCH]
• The picture is expanded horizontally.
10) Slim Mode [SLIM]
19
• The picture is expanded vertically.
13 14 15 16 17
Digital Effects 2 [EFFECT2]
11) NEGA
12) SEPIA
2 Set [TAPE RECORDING MENU] >> [DIGITAL]
>> [MULTI MODE] >> [STROBE] or [MANUAL].
20
3 Press the [MULTI] Button
.
13) B/W
14) SOLARI
20
11) Negative Mode [NEGA]
• The colors of the recorded image are inverted
as seen in a negative.
12) Sepia Mode [SEPIA]
• If [MANUAL] is selected, press the [MULTI] Button at
each scene you want to capture.
• It records a scene with a brownish tint, like the
color of old pictures.
13) Black & White Mode [B/W]
• It records an image in black and white.
14) Solarisation Mode [SOLARI]
• It records an image with a painting-like effect.
33
Recording Mode
Deleting All the Captured Multi-Pictures
While 9 multi-pictures are displayed, press the
[MULTI] Button.
• If [MANUAL] has been selected, press the [MULTI]
Button after 9 pictures are displayed.
Wipe Mode and Mix Mode
Wipe Mode:
Like drawing a curtain, the still picture of the last
recorded scene gradually changes to the moving
image of a new scene.
To Display the Multi-Pictures Again
Press the [MULTI] Button for 1 second or longer.
To Delete Multi-Pictures One by One
(When pictures were captured in [MANUAL])
When the [MULTI] Button is pressed for 1 second
or longer while the still pictures are displayed, the
pictures captured last are deleted continuously.
• After still pictures are deleted one by one, they
cannot be displayed again.
Mix Mode:
While the moving image of a new scene fades in, the
still image of the last recorded scene gradually fades
out.
• For other notes concerning this item, see page 64.
Picture-in-Picture Mode
1 Set [TAPE RECORDING MENU] >> [DIGITAL]
>> [EFFECT1] >> [WIPE] or [MIX].
You can display a sub-screen (still picture) inside the
screen.
1 Set [TAPE RECORDING MENU] >> [DIGITAL]
>> [EFFECT1] >> [P-IN-P].
19
13 14 15 16 17
• The [WIPE] or [MIX] Indication appears.
19
43
2 Press the Recording Start/Stop Button
start recording.
to
13 14 15 16 17
2 Aim the Camcorder at the scene you want to
20
capture and press the [P-IN-P] Button
insert a small still picture.
to
43
20
43
3 Press the Recording Start/Stop Button
pause the recording.
to
• The last scene is stored in memory. The [WIPE] or
• A small still picture is displayed in a normal picture.
• If the [P-IN-P] Button is pressed again, the small still
picture is cleared.
WIPE
MIX
[MIX] Indication changes to [
] or [
].
43
4 Press the Recording Start/Stop Button
restart the recording.
to
• The last image of the previous scene gradually
changes to the new scene.
• For other notes concerning this item, see page 64.
• For other notes concerning this item, see page 64.
34
Playback Mode
Adjusting the Sound Volume
Playback Mode
26
To adjust the volume, push the [W/T] Lever
to
Playing Back a Tape
display the [VOLUME] Indication. Push the [W/T]
Lever towards [T] to increase the volume or push
the [W/T] Lever towards [W] to decrease the
volume. The [VOLUME] indication disappears
immediately after adjustment is made.
The recorded scene can be played back immediately
after the recording.
44
1 Set the [OFF/ON] Switch
to [ON].
41
• The [POWER] Lamp
lights up.
44
41
26
To adjust the volume with the Remote Control,
press the [T] or [W] Button to display the [VOLUME]
Indication. Press the [T] Button to increase the
volume or press the [W] Button to decrease the
volume. The [VOLUME] indication disappears
immediately after adjustment is made.
40
2 Set the Mode Dial
to Tape Playback Mode.
40
(PV-GS9)
(PV-GS12/
PV-GS14/
PV-GS15)
17
to rewind the
3 Press the [
tape.
] Button
• The sound volume cannot be adjusted using the
Remote Control in Playback Zoom Mode. (pp. 37-38)
• For other notes concerning this item, see page 64.
17
Finding a Scene You Want to Play
Back
• Rewind the tape to the point where you want to
start playback.
Cue/Review Playback
• When the tape reaches the beginning, rewinding
stops automatically.
14
17
15
4 Press the [►] Button
to start playback.
• The [ ] Indication appears.
15
14
17
is
If the [
] Button
or [
] Button
pressed during Playback, it turns to Cue Playback
A
B
or Review Playback
A
.
B
• If a cassette recorded with copyright protection
signal is played back, the picture is distorted by
mosaic-like patterns.
To Stop Playback
Press the [ ] Button
• If the Button is held continuously, it turns to Cue
Playback or Review Playback until you release it.
16
.
16
35
Playback Mode
Scenes recorded in the SP Mode are played back at
Variable Speed Search Function
The speed of Cue Playback or Review Playback can
be varied.
approximately 1/5th of the normal speed.
Scenes recorded in the LP Mode are played back at
approximately 1/3rd of the normal speed.
15
1 During playback, press the [►] Button
.
To Resume Normal Playback
• The [1X ] Indication appears.
72
Press the [►] Button
.
15
• If the Camcorder is left in the Slow Motion Playback
Mode for more than 10 minutes, the Camcorder
switches to the Stop Mode to protect the video heads
from excessive wear and tear.
26
Still Playback/Still Advance Playback
2 Push the [W/T] Lever
search speed.
to select a desired
This Camcorder is capable of still picture playback and
frame-advance playback.
72
69
57
26
57
72
69
1 Press the [►] Button
2 Press the [ ] Button
.
The following 6 playback speeds are available for the
Variable Speed Search Function in both the
fast-forwarding and rewinding directions:
1/5X (slow playback in SP Mode only), 1/3X (slow
playback in LP Mode only), 1X, 2X, 5X, 10X and 20X.
• This function works by pressing the [VAR. SEARCH]
and cursor buttons ([▲, ▼]) on the Remote Control.
(p. 14)
.
• The playback image stops in the Still Playback
Mode.
57
on
3 Press the [
the Remote Control.
] Button or [
] Button
• With each press of the [
advance in the reverse direction.
With each press of the [
advances in the forward direction. If one of the
buttons continues to be pressed, still pictures
advance continuously 1 frame at a time until the
button is released.
] Button, still pictures
] Button, still pictures
To Resume Normal Playback
15
Press the [►] Button
.
• During Cue or Review Playback, fast-moving images
may show mosaic-like patterns.
• The sound is muted during search.
To Resume Normal Playback
72
Press the [►] Button
.
Slow Motion Playback (Remote
Control Only)
• This feature is only available with Remote Control.
However it is not supplied for models PV-GS9/
PV-GS12/PV-GS14. If you would like to order, the
parts number is LSSQ0411 as a replacement parts.
Please refer to page 74.
Playback with Zoom Lever
By pushing the [W/T] Lever
the Still Playback Mode, still pictures can be
advanced one frame at a time in the forward or
backward direction. If you keep pushing the Lever,
still pictures advance continuously.
26
Camcorder
in
of the
This Camcorder can play back at a slow speed.
72
69
57
57
26
72
1 Press the [►] Button
.
57
on
2 Press the [
the Remote Control.
• The [ ] or [ ] Indication appears.
] Button or [
] Button
• If the Camcorder is left in the Still Playback Mode for
more than 5 minutes, the Camcorder switches to the
Stop Mode to protect the video heads from excessive
wear and tear.
• When the [
Playback proceeds in the reverse direction.
When the [ ] Button is pressed, Slow Motion
Playback proceeds in the forward direction.
] Button is pressed, Slow Motion
36
Playback Mode
Scene Index Search
Index Search Functions (Remote
Control Only)
1 Set [TAPE PLAYBACK MODE] >> [PLAYBACK]
>> [SEARCH] >> [SCENE].
• This feature is only available with Remote Control.
However it is not supplied for models PV-GS9/
PV-GS12/PV-GS14. If you would like to order, the
parts number is LSSQ0411 as a replacement parts.
Please refer to page 74.
To facilitate searching for desired scenes, this
Camcorder automatically records index signals during
recording, as explained in the following.
58
] Button
2 Press the [
] Button or [
on the Remote Control.
• When the corresponding button is pressed once,
the [S 1] Indication appears, and searching for the
subsequent scene marked with an index signal
starts. Each time the button is pressed after the
start of Scene Index Search, the indication changes,
from [S 2] to [S 9], and the beginning of the scene
corresponding to the selected number will be
searched.
Photoshot Index Signal
(PV-GS9)
These signals are automatically recorded whenever
still pictures are taken in Photoshot Mode. (p. 25)
Photoshot Index Signals are not recorded on still
pictures recorded in Continuous Photoshot Mode.
(PV-GS12/PV-GS14/PV-GS15)
These signals are automatically recorded when still
pictures on a card are recorded to a tape.
Scene Index Signal
Scene Index Signals are automatically recorded
when you start recording after inserting a Cassette.
• If [SCENE INDEX] of [RECORDING] Sub-Menu on
the [TAPE RECORDING MENU] is set to [2HOUR],
an index signal is recorded when recording is
restarted after an elapse of 2 hours or longer. If it
is set to [DAY], an index signal is recorded when
recording is restarted after the date has changed
since the last recording. (While the index signal is
being recorded, the [INDEX] Indication flashes for a
few seconds.)
• Up to 9 scene numbers can be selected.
Continuous Index Search
58
is
If the [
] Button or the [
] Button
pressed for 2 seconds or longer, search can be
continued at several-second intervals. (To cancel,
72
70
.)
press the [►] Button
or the [ ] Button
72
70
58
58
• For other notes concerning this item, see page 64.
Playback Zoom Function (Remote
Control Only)
• This feature is only available with Remote Control.
However it is not supplied for models PV-GS9/
PV-GS12/PV-GS14. If you would like to order, the
parts number is LSSQ0411 as a replacement parts.
Please refer to page 74.
• If the Camcorder is switched from the Tape Playback
Mode to Tape Recording Mode or if the date and
time is set before the start of recording, the index
signal is not recorded.
A part of the image can be enlarged up to 10 times
during playback.
Photoshot Index Search
1 During playback, press the [P.B. ZOOM]
1 Set [TAPE PLAYBACK MENU] >> [PLAYBACK]
>> [SEARCH] >> [PHOTO].
74
Button
on the Remote Control.
74
56
19
56
13 14 15 16 17
58
2 Press the [
on the Remote Control.
] Button or [
] Button
• The center of the image is enlarged by approximately
2 times.
58
58
• With each press of the corresponding button, still
pictures recorded in Photoshot Mode are searched.
37
Playback Mode
Wipe Mode and Mix Mode (Remote
To Change the Zoom Magnification
Control Only)
2 Change the magnification by pressing the [W]
• This feature is only available with Remote Control.
However it is not supplied for models PV-GS9/
PV-GS12/PV-GS14. If you would like to order, the
parts number is LSSQ0411 as a replacement parts.
Please refer to page 74.
62
Button or [T] Button
Control.
on the Remote
62
72
1 Press the [►] Button
.
72
To Change the Enlarging Area of an Image
56
3 Press the Arrow Button (▲, ◄, ►, ▼)
on
the Remote Control that points to the area
you want to enlarge.
59
2 Press the [SELECT] Button
on the
Remote Control and select [WIPE] or [MIX].
To Cancel the Playback Zoom Function
59
60
61
74
Press the [P.B. ZOOM] Button
Control.
on the Remote
• For other notes concerning this item, see page 64.
60
3 Press the [STORE] Button
at the moment
Playback Digital Effect Functions
you want to save as a still picture.
WIPE
the image is saved.
MIX
] Indication appears, and
• The [
] or [
During playback, special digital effects can be added
to the recorded pictures. The same effects as those of
Digital Effects 1 and 2, which are used during
recording, are obtained.
61
4 Press the [OFF/ON] Button
in which you want to use the Wipe or Mix
in the scene
72
1 Press the [►] Button
.
effect.
• The scene changes as a result of the Wipe or Mix
effect.
72
• The Wipe Function and Mix Function can only
be accessed by using the Remote Control during
playback.
59
2 Press the [SELECT] Button
on the
Remote Control to select a desired digital
effect.
61
• If the [OFF/ON] Button
is pressed while Wipe or
Mix is carried out, the effect will stop temporarily at
61
that point. Pressing the [OFF/ON] Button
will bring back the effect.
again
59
• For other notes concerning this item, see page 64.
61
Playing Back a Memory Card (For
PV-GS12/ PV-GS14/PV-GS15)
It plays back files recorded on a Card.
• When the [SELECT] Button is pressed repeatedly,
the digital effect selection changes.
• The same setting can be done using [EFFECT
SEL] Sub-Menu on the [TAPE PLAYBACK MENU].
40
1 Set the Mode Dial
Mode.
to Picture Playback
To suspend Playback Digital Effect Temporarily
61
Press the [OFF/ON] Button
to suspend or
restart the digital effect. When the digital effect is
paused temporarily, the selected effect’s indication
flashes.
40
• The same operating can be done using [EFFECT
ON] Sub-Menu on the [TAPE PLAYBACK MENU].
To Cancel the Digital Effect
2 Start Playback.
59
Press the [SELECT] Button
repeatedly on the
► :
Starting the Slide Show
Playing back the next picture
Playing back the previous picture
Stop the Slide Show
Remote Control and clear the digital effect
indication.
:
:
:
:
Pause the Slide Show
38
Playback Mode
1
Slide Show (For PV-GS12/PV-GS14/
PV-GS15)
The recorded still pictures in the Card can be played
back like a Slide Show.
2
40
1 Set the Mode Dial
Mode.
to Picture Playback
3
1
2
3
Folder File Number
Picture Size (p. 60)
File Number
40
To Select a Desired File and Playing Back
40
1 Set the Mode Dial
Mode.
to Picture Playback
15
2 Press the [►] Button
.
40
15
• The [SLIDE ] Indication is displayed.
20
2 Press the [MULTI] Button
.
20
• Each of the pictures are played back for several
seconds.
To Pause the Slide Show
Press the [ ] Button.
• The files recorded on the Card are displayed in
Multi-Picture Mode.
• The [SLIDE ] Indication is displayed.
1
2
3
To Stop the Slide Show
Press the [ ] Button.
1
2
3
Picture Size
File Number
• For other notes concerning this item, see page 64.
Folder File Number
13 14 16
] Button
3 Press the [
/
/
/
17
to select a desired file.
20
13 14 15 16 17
• The selected file is marked with a frame.
15
4 Press either the [ENTER] Button
or the
20
[MULTI] Button
.
• The selected file is shown on the entire screen.
• For other notes concerning this item, see page 64.
39
Playback Mode
1
2
Creating a Title (For PV-GS12/
PV-GS14/PV-GS15)
You can create a title and record on a Card.
1 Recording Mode:
Set the Mode Dial
Mode or Card Recording Mode. Set the Lens
to the image you want to use for creating a
title.
• The dark portion of the image is missing 1 , and
the colors of the bright portion change in order of
black, blue, green, cyan, red, magenta, yellow and
white, after which the bright portion of the image
is missing 2 and the colors of the dark portion
change in the above order.
40
to Tape Recording
6 Select [RECORDING] and press the [ENTER]
15
Button
.
• The title is recorded on the Card.
40
• For other notes concerning this item, see page 65.
Adding a Title (For PV-GS12/PV-GS14/
PV-GS15)
1 Tape Playback Mode:
Search for the image you want to use for
creating a title and set the Camcorder to the
Still Playback Mode.
A title can be added to the picture. It is displayed in
Tape/Card Recording Mode and Tape/Picture Playback
Mode.
13
2 Set [CARD] >> [CREATE TITLE] >> [YES].
1 Set [DIGITAL] >> [TITLE IN] >> [ON].
19
13 14 15 16 17
19
36
3 Press the [PHOTO SHOT] Button
.
13 14 15 16 17
36
• The title is displayed.
19
20
2 Press the [MENU] Button
3 Press the [MULTI] Button
.
.
20
• The title is stored.
• To perform Photoshot again, select [RETURN].
4 Select [LUMINANCE] and press the [ENTER]
15
14
Button
or [
, then press the [
] Button
17
] Button
to adjust the title
• A Multi Title Screen is displayed.
15
contrast and press the [ENTER] Button
.
14
5 Press the [
] Button
or [
] Button
17
to adjust the color and press the [ENTER]
15
Button
.
1
• File Name 1
40
Playback Mode
13 14 16 17
14
or [
4 Press the [
/
/
/
]
4 Press the [
] Button
] Button
17
Button to select a desired title.
to select the number of pictures to be
15
printed, and press the [ENTER] Button
.
• [ ] Indication 2 is displayed in the picture set.
(p. 60)
5 Repeat Steps 3 and 4 and press the [MENU]
13 14 16 17
19
Button
when the setup is completed.
To Verify DPOF Setting
• The selected title is marked with a frame.
Select [VERIFY] in Step 2. The pictures for which 1
or more print is set in DPOF are played back
continuously.
20
5 Press the [MULTI] Button
• The selected title is displayed.
.
• Recording and Photoshot Recording can be made
with pictures that have titles.
• For other notes concerning this item, see page 65.
To Clear the Title Display
Protecting the Files on a Card (For
PV-GS12/PV-GS14/PV-GS15)
Set [DIGITAL] >> [TITLE IN] >> [OFF]. Or, press
66
the [TITLE] Button
on the Remote Control.
(Lock Setting)
• For other notes concerning this item, see page 65.
Precious files recorded on a Card can be locked to
prevent accidental erasure. (Even if files are locked,
the files will be deleted if the Card is formatted.)
Writing Printing Data on a Card (For
PV-GS12/PV-GS14/PV-GS15)
1 Set [PICTURE PLAYBACK MENU] >> [EDITING]
>> [FILE LOCK] >> [YES].
(DPOF Setting)
DPOF Setting Printing data (DPOF Settings), such as
the number of images to be printed, can be written to
the Card. “DPOF” means Digital Print Order Format.
19
40
1 Set the Mode Dial
Mode.
to Picture Playback
13 14 15 16 17
40
1
2 Set [PICTURE PLAYBACK MENU] >> [EDITING]
>> [DPOF SET] >> [YES] >> [VARIABLE].
2 Select the file to be locked, and press the
15
[ENTER] Button
.
• The selected file is locked and the [
]
Indication 1 appears. Repeat this procedure to
lock 2 or more files.
19
15
• Press the [ENTER] Button
again to cancel.
13 14 15 16 17
• The SD Memory Card has a write protection switch.
(p. 65)
• For other notes concerning this item, see page 65.
1
2
• When all images are not printed, select [ALL 0].
3 Select a desired picture and press the [ENTER]
15
Button
.
• The selected picture is marked with a frame.
• The number of prints set by DPOF 1 is displayed.
41
Playback Mode
Deleting the Files Recorded on a Card Formatting a Card (For PV-GS12/
(For PV-GS12/PV-GS14/PV-GS15)
PV-GS14/PV-GS15)
If a Card becomes unreadable by the Camcorder,
format it for reuse. Formatting erases all the data
recorded on a Card.
Using the Camcorder, you can delete the files
recorded on a Card. After the file is deleted, it cannot
be restored.
1 Set [PICTURE PLAYBACK MENU] >> [EDITING]
>> [CARD FORMAT] >> [YES].
To Select and Delete Files or Titles
1 Set [PICTURE PLAYBACK MENU] >> [DELETE]
>> [FILE BY SEL] >> [YES].
19
19
13 14 15 16 17
13 14 15 16 17
• A confirmation message appears, select [YES]
and formatting will be carried out.
• To erase a title in [PICTURE PLAYBACK MENU],
select [TITLE BY SEL].
2 Select the file you wish to delete and press
15
the [ENTER] Button
.
• The selected picture is marked with a frame.
• To erase 2 files or more, repeat this step.
• When the formatting is completed, the screen
becomes white.
36
3 Press the [PHOTO SHOT] Button
.
• It may not be able to use the Card formatted by this
Camcorder on another unit. In this case, format the
Card on the unit which will use the Card. Make sure
that valuable pictures are stored on your PC before
proceeding.
36
• A Card formatted on other equipment (e.g. PC) might
be unusable or it might take more time for recording.
We recommend that you use this equipment to
format the Card.
• A verification message appears.
4 Select [YES] and press the [ENTER] Button
15
.
• The selected file is deleted from the Card.
• If [NO] is selected, the file selection is canceled.
To Select and Delete All Files
1 Set [PICTURE PLAYBACK MENU] >> [DELETE]
>> [ALL FILES] >> [YES].
19
13 14 15 16 17
• A verification message appears.
2 Select [YES] and press the [ENTER] Button
15
.
• All files of Picture Playback Mode are erased.
• A locked file cannot be erased.
• If there are many files on a card, it may take
longer to delete files.
42
Playback Mode
Playing Back on Your TV
By connecting your Camcorder with your TV, the
recorded scenes can be viewed on your TV screen.
• Before connecting them, turn off the power of both
the Camcorder and TV.
1 Connect the [AV OUT] Jack of the Camcorder
and the Video and Audio Input Jacks of the
TV.
[VIDEO IN]
[S-VIDEO IN]
[AUDIO IN]
2
1
(For PV-GS14/
PV-GS15)
• Connect to the TV with the AV Cable 1 . If the TV
has an S-Video Jack, connect the S-Video Cable
(not supplied) 2 , too (For PV-GS14/PV-GS15).
• When plugging the pin plug of the AV cable into
the [AV OUT] Jack, plug it in as far as it goes.
To Make the Indications Appear on the TV
Screen
51
Press the [OSD] Button
on the Remote Control.
51
• For other notes concerning this item, see page 65.
43
Editing Mode
• When recording to tape, select the tape position
Editing Mode
Recording from a Tape onto a Card (For
PV-GS12/PV-GS14/PV-GS15)
Still pictures can be recorded on the Memory Card
from scenes that have already been recorded on a
cassette.
before recording. The picture will be recorded to the
tape position when the [PHOTO SHOT] Button is
pressed at Step 3.
• Photoshot index signals are automatically recorded.
• For other notes concerning this item, see page 65.
40
1 Set the Mode Dial
to Tape Playback Mode.
Audio Dubbing (Remote Control Only)
• This feature is only available with Remote Control.
However it is not supplied for models PV-GS9/
PV-GS12/PV-GS14. If you would like to order, the
parts number is LSSQ0410 as a replacement parts.
Please refer to page 74.
40
You can add music or narration to the recorded
Cassette.
• If the tape recorded in the [16bit] Mode is dubbed
with the Audio Dubbing function, the original sound
is erased. (If you wish to preserve the original sound,
use the [12bit] Mode when recording.)
2 Start playback and set the Camcorder to Still
Playback Mode at the scene you wish to
record, and press the [PHOTO SHOT] Button
36
.
• Audio Dubbing cannot be performed on a recording
made in LP Mode. (p. 23)
36
69
1 Press the [ ] Button
on the Remote
Control where you want to add new sound.
Recording Pictures from a Card onto
a Tape (For PV-GS12/PV-GS14/
PV-GS15)
55
69
Card Images can be recorded to the Tape.
55
2 Press the [A.DUB] Button
Control.
on the Remote
40
1 Set the Mode Dial
Mode.
to Picture Playback
3 To start Audio Dubbing, press the [ ] Button
69
on the Remote Control.
40
To Cancel Audio Dubbing
69
Press the [ ] Button
on the Remote Control.
The Camcorder is in the Still Playback Mode again.
To Play Back the Sound Recorded by 12bit
Audio Dubbing
2 Display the first picture.
Set [TAPE PLAYBACK MENU] >> [PLAYBACK] >>
[12bit AUDIO] >> [ST1], [ST2] or [MIX].
36
3 Press the [PHOTO SHOT] Button
.
ST1: It plays back only the original sound.
36
ST2: It plays back only the sound added by Audio
Dubbing.
MIX: It plays back both the original sound and the
sound added by Audio Dubbing
simultaneously.
• During the copying, the following Indication
appears.
• It takes a few seconds to record a picture to the
Tape.
44
Editing Mode
To Dub Audio While Listening to a Pre-recorded
Camcorder:
Sound
1 Insert the recorded Cassette.
When pausing the audio dubbing, set the [12bit
AUDIO] on the [PLAYBACK] Sub-Menu to [ST2]
and you can check the pre-recorded sound.
When a microphone (For PV-GS14/PV-GS15) is
used for audio dubbing, use headphones to listen
to the pre-recorded sound while dubbing the audio.
(When using headphones, set [AV JACK] on the
[INITIAL] to [OUT/PHONES].)
VCR:
2 Insert an unrecorded Cassette with an
erasure prevention tab.
• If various setups (such as external input, tape
speed, etc.) are required, please refer to the
operating instructions of your VCR.
Camcorder:
When the line input is used, you can dub audio
while listening to the pre-recorded sound from the
speaker.
3 Press the [►] Button to start playback.
VCR:
4 Start recording.
• For other notes concerning this item, see page 65.
5 Press the Pause or Stop Button to stop
recording.
Copying on an S-VHS (or a VHS)
Cassette
Camcorder:
6 Press the [ ] Button to stop playback.
(Dubbing)
After connecting the Camcorder and the VCR as
illustrated, start the following procedures.
Using the DV Cable for Recording
(Digital Dubbing)
By connecting this Camcorder with other digital video
equipment (such as another Camcorder of the same
format/model) that has a DV input/output Terminal, and
using a 4-pin to 4-pin DV Interface Cable PV-DDC9
(optional) 1 , high quality images and sounds can be
dubbed in the digital mode.
[S-VIDEO IN]
[VIDEO IN]
[AUDIO IN]
2
(For PV-GS14/
PV-GS15)
1
1
Player/Recorder:
1 Insert the Cassette and set to Tape Playback
Mode.
Player:
72
2 Press the [►] Button
to start playback.
1
2
AV Cable
S-Video Cable (not supplied)
54
69
72
70
• Be sure to press the [OSD] Button (p. 14) on
the Remote Control prior to copying so that no
indications are visible. Otherwise, the displayed tape
counter and function indications are also copied.
45
Editing Mode
Recorder:
54
3 While pressing the [ REC] Button
, press
72
the [PLAY] Button
on the Remote Control.
7
Or while pressing the [REC] Button
, press
10
the [BACK LIGHT] Button
Camcorder.
on the
7
10
• Recording starts.
To Stop Dubbing
69
70
Press the [ ] Button
or the [ ] Button
.
CAUTION:
Unauthorized exchanging and/or copying of
copyrighted recordings may be copyright
infringement.
• For other notes concerning this item, see page 65.
PC Connection With DV Interface
Cable
A video clip can be transferred directly to your PC
(Personal Computer) via a DV Interface Cable (Optional)
using products and software from a number of video
editing software companies.
Using products from video editing software companies
allows you to capture and edit video clips using the DV
Interface.
Our DVC being OHCI compliant should
have no problem working with any OHCI
compliant Firewire Card/video - Editing
software package.
• Personal Computer must be equipped with an DV
Terminal.
• During Camcorder playback, do not disconnect the
DV Interface Cable or turn the Camcorder off as this
may cause a PC hang-up error.
• 1394 (i.LINK) Interface must conform to OHCI (Open
Host Controller Interface Specification).
46
With a PC
Using USB Driver
With a PC
Operating environment
• Despite having the Operating environment indicated,
it may not be possible to use the program with some
types of personal computers.
• A CD-ROM drive is requires to install this program.
OS:
Using the Software with a Personal
Computer
An image stored on the DV Cassette or Memory
Card can be transferred to your personal computer.
Software Installation (For Windows)
1 Turn on the personal computer and start up
Windows.
IBM PC/AT compatible personal computer with
preinstalled;
Microsoft Windows XP Home Edition/Professional
Microsoft Windows 2000 Professional
Microsoft Windows Me (Millennium Edition)
Microsoft Windows 98 Second Edition
CPU:
2 Insert the CD-ROM into the personal
computer’s CD-ROM drive.
• The [Setup Menu] screen appears.
Intel Pentium ll/Celeron 300 MHz or higher
(including compatible CPU)
RAM:
32 MB or more (64 MB or more recommended)
(128 MB or more required for Windows XP)
Free hard disk space:
At least 30 MB or more
Ports:
[PV-GS15: Supplied] [PV-GS9/PV-GS12/PV-GS14:
Optional Software]
USB Jack
3 Select the software to be installed from [Setup
Menu].
Installing USB Driver
Please install USB Driver first before connecting the
Camcorder to your personal computer with the USB
Cable.
● USB Driver (pp. 47-49) :
Software for USB Driver allows you to transfer
images directly from the Memory Card into the
computer.
1 Turn on the personal computer and start up
Windows.
● WebCam Driver (pp. 50-53) :
If the Camcorder is connected to your personal
computer, you can send video from the Camcorder
to the other parties via the network.
● DV STUDIO 3.1E-SE (Optional Software)
(pp. 53-55) :
2 Insert the CD-ROM into the personal
computer’s CD-ROM drive.
• Quit all applications.
• The [Setup Menu] Screen appears.
With DV STUDIO 3.1E-SE software, your favorite
scene on a tape can be captured to your personal
computer as a still image. Also, images viewed
through the camera lens can be captured to your
personal computer.
● ArcSoft Software (pp. 55-56) :
PhotoImpression 4 and PhotoBase 4 are included.
● Acrobat Reader (Optional Software) :
To view the installed operating instructions, Adobe
Acrobat Reader 5.0 or higher is required. Please
install Adobe Acrobat Reader from the CD-ROM
(Optional Software).
[PV-GS15: Supplied] [PV-GS9/PV-GS12/PV-GS14:
Optional Software]
3 Click the [USB Driver].
• The set up program starts running.
4 For Windows 98SE/Me/2000 users, click
[Restart] if the [InstallShield] dialog appears.
• Do not remove the CD-ROM.
4 Follow the instructions on the computer
screen until the installation is complete.
• Setup window will disappear when the installation
is complete.
• If a window does not appear automatically, click the
“Start” Button on your desktop and then click “Run”.
When the “Run” Box is open, type in “D:\InstMenu.exe”
and click “OK”. (“D” applies when the CD-ROM drive
is drive D.)
47
With a PC
5 Finish installation by following the on-screen
instructions.
• Click [Next] and proceed with installation.
• After completing the installation, Click [Finish].
Connecting the Personal Computer and
Camcorder
Please install the USB Driver first before
connecting the Camcorder to your Personal
Computer with the USB Cable.
6 After the USB Driver is installed, please
restart your computer.
• Reboot the computer to finish installing USB
Before making these connections, turn off all devices
which are to be connected.
• When using the USB Connection Kit, use of the AC
Adaptor is recommended for the power supply of the
Camcorder.
driver.
• Installation continues after the computer reboots if
you selected additional software.
• A message indicating a conflict between versions
may be displayed during the installation. This will not
cause a problem. Simply click [Yes] to proceed with
the installation.
• Depending on the OS version, illustrations and icon
names may vary.
For Using Built-in SD Drive
(For PV-GS12/PV-GS14/PV-GS15)
By connecting the Camcorder and Personal Computer
with the USB Cable, you can transfer still images
saved on a Memory Card directly to your Personal
Computer.
Windows 98SE/Me Users
(For Windows)
The following messages may be displayed when
connecting this Camcorder and your personal
computer via USB Cable.
1 Insert the Memory Card into the Camcorder.
2 Set the Camcorder to PC Mode.
1 For Windows 98SE Users:
The message, “Please insert the disk labeled
‘Windows 98 Second Edition CD-ROM’,.....” is
displayed. Click [OK].
3 Connect the Camcorder to your personal
computer with USB Cable.
1) The message “The file ‘kstvtune.ax’ on [Unknown]
cannot be found...” is displayed.
• Enter “C:\Windows\system” for Windows 98SE.
Enter “C:\Windows\options\CABS” for Windows
Me.
• If the “kstvtune.ax” file is missing in one of the 2
above-mentioned folders, insert the OS CD-ROM
and assign the path.
2) The message “The file ‘ksclockf.ax’ on [Unknown]
cannot be found...” is displayed.
• It enters PC Connecting Mode.
• Enter “C:\Windows\system”.
4 Open [My Computer] and click [Removable
Disk] 1 (For Windows 98SE/Me/2000 users).
• If the “ksclockf.ax” file is missing in the above
mentioned folder, insert the OS CD-ROM and
assign the path.
Click [Open folder to view files using
Windows Explorer] 2 and then [OK] (For
Windows XP users).
3) The message “MTDV98M3.pdr is not found” is
displayed.
• Enter “C:\Windows\system\IOSUBSYS”.
4) The message “MTDV98M3.sys is not found” is
displayed.
• Enter “C:\Windows\SYSTEM32\DRIVERS”.
• You may click [Browse] to look for and assign the
path.
48
With a PC
[Windows 98SE/Me/2000]
[Windows XP]
To disconnect USB cable safely
(For Windows)
If USB Cable is disconnected while computer is on,
error dialog may appear. In such case click [OK] and
close the dialog box. By following the steps below you
can disconnect the cable safely.
1
2
1 Double click the
icon in task tray.
• Hardware disconnect dialog appears.
• You can view images stored on the Memory Card
and also save them to your hard disk.
• Please do not change file or folder names on the
Personal Computer. The images on the Memory
Card may not be able to be viewed on the
Camcorder.
2 Select [USB Mass Storage Device] 1 and
click [Stop].
(For Macintosh)
OS:
Mac OS X v 10.1 – X v 10.2
3 Verify [Matshita DVC USB Device] is selected
and click [OK].
CPU:
iMac, iBook or Power Book G4, Power Mac G4 or
Power Mac G5
RAM:
1
64 MB or more
1 Insert the Memory Card into the Camcorder.
2 Set the Camcorder to PC Mode.
• You can safely disconnect the cable.
Note on the driver name 1 displayed
The driver name displayed will differ depending on
your OS, operating environment and the mode of the
Camcorder.
Windows XP/2000:
• When the Camcorder is in Tape Recording mode or
Tape Playback Mode:
3 Connect the Camcorder to your Macintosh
with USB Cable.
[Panasonic DVC USB-SERIAL Driver for WinXXXX
(COM X)] (The numeral designation after “Win” will
differ depending on the OS. The numeral after “COM”
will differ depending on the operating environment of
your personal computer.)
• When the Camcorder is in PC Mode:
[USB Mass Storage Device] or [Panasonic DV DISK
Port Driver]
Windows Me:
• When the Camcorder is in PC Mode:
[USB Disk]
4 Double click the “NO_NAME” icon.
• You can view images stored on the Memory Card
and also save them to your hard disk.
• Please do not change file or folder names on the
Personal Computer. The images on the Memory
Card may not be able to be viewed on the
Camcorder.
• Some OS, such as Windows 98SE, may not show
the icon indicating that you may safely disconnect in
task tray. (OS may be set not to 1 show) Make sure
Camcorder’s Card Access lamp is off and disconnect
the cable. Also, with Windows Me, the icon will not
be displayed when in Tape Recording Mode or Tape
Playback Mode.
CAUTION:
If you disconnect the USB Cable while the Card
Access Lamp is on, it may damage the Card
data.
49
With a PC
Operating environment
(For Macintosh)
Removing the USB Cable safely for
Macintosh
OS:
IBM PC/AT compatible personal computer with
preinstalled;
Microsoft Windows XP Home Edition/Professional
(In this case of Windows XP, SP1 or later is needed.)
Microsoft Windows 2000 Professional
Microsoft Windows Me (Millennium Edition)
Microsoft Windows 98 Second Edition
CPU:
Intel Pentium ll/Celeron 300 MHz or higher
(including compatible CPU)
RAM:
32 MB or more (64 MB or more recommended)
(128 MB or more required for Windows XP)
Free hard disk space:
1 Drop the [NO_NAME] icon which appeared
when you connected the Camcorder with the
USB Cable into the recycle bin, then disconnect
the USB Cable.
If the above operation is not performed correctly, when
data is copied from the personal computer to an SD
Memory Card, the copied data may be damaged.
At least 250 MB or more
Ports:
USB Jack
Even when the following operations are performed, the
same results will occur as when the USB Cable is
removed (above). Therefore, it is imperative that the
above operation 1 is completed before proceeding.
To use the Camcorder as a Web Camera, the
additional minimum requirements must be met.
Graphic display:
High Color (16 bit or more)
Desktop resolution of 800 x 600 pixels or more
• When Camcorder power is turned OFF.
Communication Speed:
56 kbps or faster is recommended.
Necessary software:
Windows Messenger 5.0 or later (Windows XP)
MSN Messenger (Windows 98SE/Me/2000)
Other requirements (to send/receive audio):
Sound card
• When SD Memory Card is removed.
Speaker or headphones
To use the Camcorder as a Web Camera, the
following conditions must be met.
• To upgrade Windows XP to SP1, click [Start] >> [All
Programs] >> [Windows Update]. (Requires Internet
connection.)
• You have direct dial-up connection capability to the
Internet. Also, you and the other person(s) are in the
same Network (LAN).
• Install the Windows Messenger (Windows XP) or
MSN Messenger (Windows 98SE/Me/2000). If you
have a version older than 5.0, please download the
latest version (5.0 or later) from the Microsoft Home
Page:
Using as a Web Camera
If the Camcorder is connected to your personal
computer, you can send video and sound from the
Camcorder to the other parties via the network.
• Do not connect the USB Cable until the WebCam
Driver is installed.
This feature can be used only if both parties are
using the same operating system. Please see chart
below.
[Send]
[Receive]
[Software]
Windows
Messenger
Windows XP <--OK--> Windows XP
(For download and installation instructions, please
refer to Help on the Home Page.)
• If you are connected to the Internet through a
firewall or a router, proper communication will not be
possible.
Windows
Windows XP <--NG-->
98SE/Me/2000
Windows
98SE/Me/2000
Windows
98SE/Me/2000 Messenger
MSN
<--OK-->
• The installer is available only in English but can be
used on operating systems using other languages.
• When DirectX9.0 is installed, applications supported
by previous versions of DirectX may not run.
50
With a PC
3 Connect the Camcorder to your personal
computer with USB Cable.
Installing WebCam Driver
1 Turn on the personal computer and start up
Windows.
2 Insert the CD-ROM into the personal
computer’s CD-ROM drive.
• Quit all applications.
• The [Setup Menu] Screen appears.
• “WEB” is displayed on the LCD Monitor of the
Camcorder.
• When the Camcorder and personal computer (with
Windows 2000) are connected via USB Cable, a
message, such as the one below, is displayed.
However, testing by the manufacturer has
confirmed functionality of this Camcorder with
Windows 2000. Click [Yes] and proceed.
[PV-GS15: Supplied] [PV-GS9/PV-GS12/PV-GS14:
Optional Software]
3 Click the [WebCam Driver].
• The set up program starts running.
4 For Windows XP users:
Depending on your system environment,
installation of “DirectX9.0b” may be required.
Click [Yes] and continue with installation.
• After “DirectX9.0b” is installed, the computer will
restart.
• Do not remove the CD-ROM.
• For Windows 98SE/Me users, “USB Audio
Device” is required. Click [Next] and proceed.
5 Finish installation by following the on-screen
instructions.
• Click [Next] and proceed with installation.
• After completing the installation, click [Finish].
• If you use Windows 98SE, the OS installation CD
may be required.
Connecting the Camcorder to Personal
Computer (For Using as a Web Camera)
1 Set the Camcorder to Tape Recording Mode
or Tape Playback Mode.
4 Start the Windows Messenger (For Windows
XP users) or MSN Messenger (For Windows
98SE/Me/2000 users).
• Click [Start] >> [All Programs (Program)] >>
[Windows Messenger] or [MSN Messenger].
• When you use Windows XP, the other parties via the
network have to use the Windows Messenger on
Windows XP. When you use other than Windows XP,
the other parties via the network have to use MSN
Messenger on an OS other than Windows XP.
• If the Camcorder is used as a Web Camera, the
quality of the video to be exchanged will depend on
the Internet connection status.
(PV-GS9)
(PV-GS12/
PV-GS14/
PV-GS15)
2 Set [CAMERA] or [PLAYBACK] >> [USB
FUNCTION] >> [WEB CAMERA].
• If the USB Cable is disconnected from the personal
computer, the Web Camera mode is canceled.
• If the Camcorder is used as a Web Camera, video
cannot be recorded onto a tape or a card.
19
13 14 15 16 17
51
With a PC
6 Click on [Audio Tuning Wizard...] in the [Tools]
menu to confirm that equipment is connected
correctly.
Setting up the Windows Messenger
When starting the Windows Messenger for the first
time, its setup screen is displayed. (However, the
screen is not displayed if the Windows Messenger
setup has already been done.) For more details,
please read the corresponding Help file.
1 Click [Click here to sign in].
7 Select [USB Video Device] in the [Camera]
menu.
2 Select [.NET Messaging Service] and click
[OK].
8 Select [DVC] in the [Microphone] menu.
3 Click [Next] when the [.NET Passport Wizard]
dialog appears.
• For other information about Windows Messenger,
please refer to Help.
• When access is finished, close Windows Messenger,
then turn off the Camcorder. Finally, disconnect the
USB Cable.
• If the Camcorder is used as Web Camera
continuously for two hours, the communication is
automatically shut OFF. In this case, restart Windows
Messenger and set up the communication again.
4 Please carefully read the displayed contents
and then proceed.
5 After the setup is completed, sign in and start
the Windows Messenger.
Setting up the MSN Messenger
When starting the MSN Messenger for the first time,
its setup screen is displayed. (However, the screen is
not displayed if the MSN Messenger setup has already
been done.) For more details, please read the
corresponding Help file.
1 Click [Sign In].
52
With a PC
2 Type in your Sign-in name and password.
• If you do not have your Sign-in name and
password, click [Get one here].
8 Confirm the [Panasonic DVC Web Camera
Device] 1 is selected.
1
• For other information about MSN Messenger, please
refer to Help.
3 Please carefully read the displayed contents
and then proceed.
• If the Camcorder is used as a Web Camera
continuously for two hours, the communication is
automatically shut OFF. In this case, restart MSN
Messenger and set up the communication again.
• When access is finished, close MSN Messenger,
then turn off the Camcorder. Finally, disconnect the
USB Cable.
4 After the setup is completed, sign in and start
the MSN Messenger.
5 Click on [Audio Tuning Wizard...] in the [Tools]
menu to confirm that equipment is connected
correctly.
Using the DV STUDIO 3.1E-SE (Optional
Software)
Following Software is not supplied with the Camcorder;
• LSFT0577 (DV STUDIO 3.1E-SE)
• K1HA05CD0005 (USB Cable)
The Software allows you to capture a still image from
your motion video on the tape and transfer to a PC. If
you would like to order, please refer to page 74.
Operating environment
OS:
IBM PC/AT compatible personal computer with
6 Select [USB Audio Device] in the [Microphone]
menu.
preinstalled;
Microsoft Windows XP Home Edition/Professional
Microsoft Windows Me (Millennium Edition)
Microsoft Windows 98 Second Edition
CPU:
Intel Pentium II/Celeron 300 MHz or higher
(including compatible CPU)
Graphic display:
High Color (16 bit or more)
Desktop resolution of 800 x 600 pixels or more
RAM:
7 Click [Web Camera Settings...] in the [Tools]
menu.
32 MB or more (64 MB or more recommended)
(128 MB or more required for Windows XP (256 MB or
more recommended))
Free hard disk space:
At least 20 MB
Ports:
USB Jack
Other requirements:
Mouse
53
With a PC
• The DV STUDIO 3.1E-SE cannot be operated on
Windows 2000.
5 After the completion of setup, click on [Finish].
• When 2 or more USB devices are connected to a
personal computer, or when devices are connected
through USB hubs or by using extension cables,
proper operation is not guaranteed.
• When connected to the keyboard USB Jack, normal
function may not be possible.
• This instruction manual describes only the
procedures for installation, connection and startup.
Please read the PDF-based instructions for how to
use the DV STUDIO 3.1E-SE.
• To view the installed operating instructions, Adobe
Acrobat Reader 5.0 or higher is required. Please
install Adobe Acrobat Reader from the CD-ROM
(Optional Software).
• Before using for the first time, select [Readme] from
[Start] >> [All programs (Programs)] >> [Panasonic]
>> [DV Studio3], and read any supplementary details
or updates.
• Installation will be completed.
• Sample data is installed concurrently with the DV
STUDIO 3.1E-SE software.
To Use DV STUDIO 3.1E-SE
• When using the USB Connection Kit, use of the AC
Adaptor is recommended for the power supply of the
Camcorder.
1 Set the Camcorder to Tape Recording Mode
or Tape Playback Mode.
• To capture images from a tape, set the Camcorder
to Tape Playback Mode and insert a tape.
• To capture images viewed through the camera
lens, set the Camcorder to Tape Recording Mode.
Installing DV STUDIO 3.1E-SE
(Optional Software)
1 Turn on the personal computer and start up
Windows.
2 Insert the CD-ROM into the personal
computer’s CD-ROM drive.
• Quit all applications.
(PV-GS12/
PV-GS14/
PV-GS15)
(PV-GS9)
• The [Setup Menu] Screen appears.
2 Set [CAMERA] or [PLAYBACK] >> [USB
FUNCTION] >> [DV STUDIO].
19
3 Click [DV STUDIO].
4 Click [Next].
13 14 15 16 17
3 Connect the Camcorder to your personal
computer with USB Cable.
• After reading the displayed contents, please carry
out the installation according to instructions.
54
With a PC
4 Select [Start] >> [All Programs (Programs)]
>> [Panasonic] >> [DV Studio3] >> [DV
Studio3].
Operating environment
(For Windows)
OS:
IBM PC/AT compatible personal computer with
pre-installed;
Microsoft Windows XP Home Edition/Professional
Microsoft Windows 2000 Professional
Microsoft Windows Me (Millennium Edition)
Microsoft Windows 98 Second Edition
CPU:
Pentium ll-based PC or equivalent ( 1 )
Pentium-based PC or equivalent ( 2 )
(Pentium II 300 MHz or higher recommended)
Graphic display:
• If a short-cut icon has been created on the desktop
during installation, it is also possible to start by
double-clicking on the icon.
• For other information about DV STUDIO 3.1E-SE
Software, please refer to Help.
High Color (16 bit or more)
Desktop resolution of 800 x 600 pixels or more
RAM:
64 MB or more (128 MB or more recommended)
Free hard disk space:
At least 625 MB
Using the ArcSoft Software (PV-GS15:
Supplied)
There are 2 types of image editing software in the
ArcSoft Software package.
Other requirements:
Mouse
(For Macintosh)
OS:
1 PhotoBase 4 (Windows), PhotoBase 2 (Mac)
Mac OS 9 – X
CPU:
iMac, iBook or Power Book G4, Power Mac G4 or
Power Mac G5
Graphic display:
High Color (16 bit or more)
Desktop resolution of 800 x 600 pixels or more
RAM:
• Create albums of image, video, audio, and other
electronic files for easy viewing, retrieval, and
management.
64 MB or more (128 MB or more is recommended)
2 PhotoImpression 4 (Windows, Mac)
Free hard disk space:
At least 300 MB
• This instruction manual describes only the
procedures for installation, connection and startup.
Please read the Help messages of your software for
how to use the ArcSoft Software.
Installation of ArcSoft Software
(For Windows)
• Easy-to-use photo editing program to edit, enhance,
retouch or add special effects to any image. Also
offers creative solutions for making greeting cards
and calendars.
1 Turn on the personal computer and start up
Windows.
2 Insert the CD-ROM into the personal
computer’s CD-ROM drive.
• Quit all applications.
• The [Setup Menu] Screen appears.
55
With a PC
3 Click [ArcSoft].
5 Double click [PhotoBase] or
[PhotoImpression] folder.
4 Select the desired language on the [Choose
Setup Language] dialog, and click [OK].
6 Double click [English] or [French] folder.
7 Double click [PhotoBase Installer] or
[PhotoImpression Installer].
• Installation begins.
8 Follow the instructions on the computer
screen until the installation is complete.
• Installation begins.
• After reading the displayed contents, please carry
out the installation according to instructions.
• If a language other than the OS language is
selected, the characters may not be presented
correctly.
To start ArcSoft Software
(For Windows)
1 Select [Start] >> [All Programs (Programs)]
>> [ArcSoft Software Suite] >> [PhotoBase 4]
or [PhotoImpression 4].
• For other information about ArcSoft Software,
please refer to Help.
5 When the component selection screen is
displayed, check the software to be installed
and click [Next].
6 After the completion of setup, click on [Finish].
(For Macintosh)
1 Double-click the [PhotoImpression] or
[PhotoBase] icon on the desktop.
• For other information about ArcSoft Software,
please refer to Help.
For Information on ArcSoft Software:
TEL:
1-510-440-9901
• Installation will be completed.
If you no longer need software or
driver (Uninstall)
(For Macintosh)
1 Turn on computer and start up Macintosh.
2 Insert the CD-ROM into the CD-ROM drive.
3 Double click the Panasonic icon.
The screens may vary with the type of the OS.
1 Select [Start] (>> [Settings]) >> [Control
Panel], select the software or the driver from
[Add/Remove Programs] to uninstall.
• Uninstalling steps may vary depending on the OS.
Please refer to the user manual of your OS.
2 After software or driver is uninstalled, please
restart your computer.
4 Double click [ArcSoft] folder.
56
With a PC
• When you are using Windows XP or Windows 2000,
Notes
you may install or uninstall this software after logging
ON by setting the user name to Administrator or to a
user name having equivalent authority.
• If you install the USB Driver after the USB Cable is
connected, or if you do not follow these Operating
Instructions, the Camcorder will not be recognized
correctly. In this case, delete the USB Driver from
[Device Manager] as described below, uninstall the
USB Driver, and re-install it.
• With the Camcorder and personal computer
connected via a USB Cable, open the [Device
Manager]. Right-click [!DVC] 1 in [Ports] or [Other
devices], and select [Uninstall].
([!DVC] 1 will differ depending on the OS or
operating environment of your personal computer.)
• Macintosh is a registered trademark of Apple
Computer, Inc. ArcSoft, the ArcSoft logo, ArcSoft
PhotoImpression 4 and ArcSoft PhotoBase 4 are
trademarks of ArcSoft, Inc.
• Microsoft® Windows®, Windows Messenger®, MSN
Messenger® and DirectX® are either trademarks or
registered trademarks of the Microsoft Corporation in
the United States and/or other countries.
• Intel®, Pentium® and Celeron® are the registered
trademarks or trademarks of the Intel Corporation.
• All other names, company names, product names,
etc. in these instructions are the trademarks
or registered trademarks of their respective
corporations.
• The names of the products you are using may differ
from the names given in the text. Depending on
the operating environment and other factors, the
contents of the screens used in these instructions
may not necessarily match what you will see on your
screen.
• Although the screens in these Operating Instructions
are shown in English for the sake of example, other
languages are supported as well.
1
• In this Manual, the Panasonic make digital video
camera with USB Jack is referred to as Camcorder.
• These instructions do not cover the basic operations
of the personal computer or define any terms. For
this information, refer to the Operating Instructions
which accompany your personal computer.
• Do not disconnect USB Cable while the operation
light of Camcorder is on. It may freeze the software
or destroy the data in transfer.
• We recommend using the AC adaptor as the
power source for the Camcorder when using USB
Connection Kit. Data may be lost if the battery power
is lost while transferring data.
• If the Camcorder is used as a Web Camera while
virus checking software is running, the Camcorder’s
operation may stop midway through. In this case,
exit the Windows Messenger or MSN Messenger,
reconnect the Camcorder and restart the Windows
Messenger or MSN Messenger.
About the SD Memory Card and
MultiMediaCard
(For PV-GS12/PV-GS14/PV-GS15)
SD Memory Card
The SD Memory Card (PV-GS15: Supplied, PV-GS12/
PV-GS14: Optional) is virtually the same size as a
MultiMediaCard. It is an external memory card that is
available in larger capacities. It has a write protect
switch to prevent data writing and card formatting, as
well as a copyright protection function.
• SD Logo is a trademark.
MultiMediaCard (Optional)
The MultiMediaCard is a compact, lightweight and
removable external memory card.
• Do not delete the folders in the memory card such as
picture folder. Memory card may not be recognized if
folders are deleted.
• All other company and product names in the
operating instructions are trademarks or registered
trademarks of their respective corporations.
Files recorded on a SD Memory Card or
MultiMediaCard
It may not be possible to play back the files on this
Camcorder recorded on and created by other
equipment or vice versa. For this reason, check the
compatibility of the equipment in advance.
• When the Camcorder is connected to a personal
computer in PC Mode, it will not be possible
to change to other modes. To change modes,
disconnect the USB cable, switch the Camcorder
Mode Dial, then reconnect the USB cable.
• When the Tape Recording Mode of the Camcorder is
switched to the PC Mode, a warning message may
be displayed. You may simply ignore it.
57
With a PC
• The memory capacity indicated on the SD Card
About the compatibility of the card files
label corresponds to the total card capacity.
Some of this capacity is used to protect and
manage the copyright data, and not all capacity is
available as a conventional memory for a
Camcorder, Personal Computer or others.
Capacity that can be used as conventional
memory:
(For PV-GS12/PV-GS14/PV-GS15)
Data files recorded on an “SD Memory Card” or a
“MultiMediaCard” by this Camcorder conform with
DCF (Design rule for Camera File system) established
by JEITA (Japan Electronics and Information
Technology Industries Association).
• If you attempt to play back files recorded with this
Camcorder on other equipment or to play back files
recorded with other equipment on this Camcorder,
you may not be able to play them back. Please
check the compatibility with the other equipment in
advance.
8 MB Card: about 6,800,000 bytes
About the folder structure when using
the Memory Card in a personal
computer
(For PV-GS12/PV-GS14/PV-GS15)
• When a Card with data recorded on it is inserted
into a personal computer, folders will be displayed
as in the figure.
[100CDPFP]:
The images (IMGA0001.JPG, etc.) in this folder are
recorded in the JPEG format.
[MISC]:
Files in which DPOF Data has been set to the image
are in this folder.
[TITLE]:
This contains the data of the original titles
(USR00001.TTL, etc.).
• [DCIM], [IM01CDPF], [PRIVATE], [VTF], etc. are
necessary items in the folder structure. They
have nothing to do with actual operations.
• In the Card Mode, the Camcorder automatically
saves file numbers (IMGA0001.JPG, etc.) along
with the images. The file numbers are recorded
with each image as consecutive numbers.
• When using software without an indication
function, indication data, such as date, are not
displayed. Depending on the software in use, the
date and the time may not be displayed correctly.
58
Others
Low Light Mode (Program AE) (p. 30)
Spotlight Mode (Program AE) (p. 30)
:
Others
:
:
Indications
Surf & Snow Mode (Program AE)
(p. 30)
Various functions and the Camcorder status are
shown on the screen.
: Remaining Battery Power
• When the battery power becomes low, the Indication
changes. When the battery is discharged completely,
REC:
Recording (p. 24)
PAUSE:
Recording Pause (p. 24)
Self-Timer Recording (p. 27)
Playback (p. 35)
:
:
the
(
) Indication flashes.
R0:45: Remaining Tape Time
:
Still Playback (p. 36)
• Remaining tape time is indicated in minutes. (When
it reaches less than 3 minutes, the indication starts
flashing.)
:
Fast-forward/Cue Playback (p. 35)
Rewind/Review Playback (p. 35)
Slow Motion Playback (p. 36)
Still Advance Playback (p. 36)
Index Search (p. 37)
:
,
:
:
:
:
Tape Recording Mode (p. 24)
Tape Playback Mode (p. 35)
,
:
,
:
Card Recording Mode (p. 25)
CHK:
Recording Check (p. 24)
Audio Dubbing (p. 44)
(For PV-GS12/PV-GS14/PV-GS15)
A.DUB
A.DUB
BLANK:
:
:
Picture Playback Mode (p. 38)
(For PV-GS12/PV-GS14/PV-GS15)
:
Audio Dubbing Pause (p. 44)
Blank Search (p. 24)
PC Mode (p. 48)
:
(For PV-GS12/PV-GS14/PV-GS15)
R
:
Repeat Playback (p. 64)
Variable Speed Search (p. 36)
CINEMA:
D.ZOOM:
MULTI:
Cinema Mode (pp. 29-30)
Digital Zoom (p. 27)
Multi Mode (p. 33)
2X
:
1/500:
When you adjust shutter speed
manually, this indication appears.
(p. 32)
P-IN-P:
WIPE:
P-IN-P Mode (p. 33)
Wipe Mode (p. 33)
SLIDE
SLIDE
F2.4:
:
Slide Show Playback (p. 39)
:
Slide Show Playback Pause (p. 39)
MIX:
Mix Mode (p. 33)
When you adjust the F Number
manually, this indication appears.
(p. 32)
STROBE:
TRAIL:
Strobe Mode (p. 33)
Trailing Effect Mode (p. 33)
Mosaic Mode (p. 33)
Mirror Mode (p. 33)
MOSAIC:
MIRROR:
AWB:
:
Automatic White Balance Mode (p. 30)
White Balance Adjustment Mode
(p. 30)
STRETCH: Stretch Mode (p. 33)
SLIM:
NEGA:
SEPIA:
B/W:
Slim Mode (p. 33)
:
:
Outdoor Mode (p. 30)
Negative Mode (p. 33)
Sepia Mode (p. 33)
Indoor Mode (recording under
incandescent lamp) (p. 30)
Black & White Mode (p. 33)
Solarisation Mode (p. 33)
Playback Zoom (p. 37)
MAGICPIX: MagicPix Function (p. 29)
Z.MIC: Zoom Microphone (p. 27)
WIND CUT: Wind Noise Reduction (p. 29)
SOLARI:
ZOOM:
SP:
Standard Play Mode (Recording Speed
Mode) (p. 23)
P
Progressive Photoshot Mode (p. 25)
Soft Skin Mode (p. 29)
Picture (p. 39)
:
SOFT SKIN
PICTURE:
TITLE:
:
LP:
Long Play Mode (Recording Speed
Mode) (p. 23)
Title picture (p. 40)
INDEX:
S 1:
Index signal recording (p. 37)
Search Number (p. 37)
VOLUME:
Volume adjustment (p. 35)
3:30:45AM: Date/Time Indication (p. 60)
5X:
Zoom Magnification Indication
(pp. 27-28)
N (F, E):
Photoshot Picture Quality (during
Photoshot recording)
[F] means Fine, [N] means Normal and
[E] means Economy. (p. 25)
AUTO:
MNL:
EIS:
Automatic Mode (p. 24)
Manual Mode (pp. 30-32)
Image Stabilizer (p. 28)
0:
:
Remaining Number of Photoshot
pictures
12 bit, 16 bit: Audio Recording Mode (p. 23)
RapidFire Consecutive Photoshot
Recording (p. 26)
MF:
Manual Focus (p. 32)
:
:
Back Light Mode (p. 29)
:
:
Lock Setting (p. 41)
Sports Mode (Program AE) (p. 30)
Portrait Mode (Program AE) (p. 30)
LED Video Light is on. (p. 26)
:
59
Others
GAINUP:
(White):
Gain up Mode (p. 26)
Initializing the Modes
You can change the Menu settings back to the
shipping condition.
DPOF Setting completed (set to 1 or
more picture) (p. 41)
640
:
[640 x 480] Image size
1 Set [INITIAL] >> [INITIAL SET] >> [YES].
• The initializing takes a little while.
• After the initializing is completed, the [COMPLETED]
Indication appears with beeps.
• Initializing will not erase a clock setting (p. 23) that
has been adjusted.
• For images not recorded with this Camcorder, the
size display is determined as follows according to
the number of horizontal pixels.
640
:
640 or more, less than 800 (The size
is not displayed at under 640 pixels.)
SVGA
:
800 or more, less than 1 024
1 024 or more, less than 1 280
1 280 or more, less than 1 600
1 600 or more, less than 2048
2 048 or more
XGA
:
Warning/Alarm Indications
SXGA
UXGA
QXGA
:
If any one of the following indications lights up or
flashes, please check the condition of the Camcorder.
:
:
DEW (DEW DETECTED/EJECT TAPE):
Condensation has occurred. (pp. 66-67)
(CHECK REC TAB):
PICTURE
(Cyan): Photoshot Mode
PICTURE
(Red): While Photoshot recording is
activated
PICTURE
PICTURE
(Green): While the Card being read
The accidental erasure prevention slider on the
inserted Cassette is open (that is, set to [SAVE]).
You are attempting Audio dubbing or Digital
dubbing on a Tape while setting the accidental
erasure prevention slider to [SAVE].
No Card (Still Picture Mode)
(Red):
To Change the Counter Display Mode
By changing [C.DISPLAY] on the [DISPLAY]
Sub-Menu, you can change the Counter Display Mode
to Tape Counter Indication [COUNTER] (0:00.00),
Memory Counter Indication [MEMORY] (M0:00.00),
and Time Code Indication [TIMECODE] (0h00m00s00f).
(p. 21) By repeatedly pressing the [DISPLAY] Button
on the Remote Control, you can change the Counter
Display Mode.
(TAPE NOT INSERTED):
No Cassette in inserted. (p. 17)
(LOW BATTERY):
The Battery is low. Recharge it. (p. 15)
:
The built-in battery is low. (p. 23)
(NEED HEAD CLEANING):
The video heads are dirty. (p. 67)
END (TAPE END):
To Display Date/Time Indication
To display Date/Time Indication, set the appropriate
Date/Time in [DATE/TIME] on the [DISPLAY]
Sub-Menu. (p. 21)
You can also press the [DATE/TIME] Button of the
Remote Control repeatedly to display or change the
Date/Time Indication.
The tape came to an end during recording.
REMOTE (CHECK REMOTE MODE):
Wrong Remote Control Mode has been selected.
(p. 15)
UNPLAYABLE TAPE
(OTHER FORMAT):
To Change the Display Mode
By changing [DISPLAY] on the [DISPLAY] Sub-Menu,
you can change the Display Mode to All Function
Display [ALL] and Minimum Display [OFF]. (p. 21)
You are attempting to play back a tape section
that has been recorded with a different TV system.
UNABLE TO A.DUB
(LP RECORDED):
Progressive Photoshot
You cannot use the Progressive Photoshot Function in
the following cases.
Because the original recording was done in LP
Mode, audio dubbing cannot be performed.
When using Tape Recording Mode
• Digital Effect Modes in [EFFECT1]
• Digital Zoom [D.ZOOM]
• 1/750 s or faster shutter speed
• When brightness is insufficient
• When the MagicPix Function is ON
• When the Portrait is used
When using Card Recording Mode
• When brightness is insufficient
• When the MagicPix Function is ON
INCOMPATIBLE TAPE:
This cassette is incompatible.
PUSH THE RESET SWITCH:
Irregular mechanism is detected. Press the
[RESET] Button (p. 70). This may solve the
problem.
CARD FULL:
Card does not have sufficient memory remaining.
Select Picture Playback Mode and delete
unnecessary files.
60
Others
NO CARD:
Card is not inserted.
NO DATA:
There are no recorded files in the card.
Notes and Hints
Concerning the Power Supply
• When the Camcorder has been used for a long time,
the Camera body becomes warm, but this is not a
malfunction.
UNPLAYABLE CARD:
• If the [CHARGE] Lamp does not light up although
the Battery is attached to the AC Adaptor, detach the
Battery and reattach it.
You are attempting to play back data which is not
compatible with this Camcorder.
CARD ERROR:
The Card is not compatible with this Camcorder.
COPY INHIBITED:
Inserting/Removing the Cassette
• In the case of using a previously recorded Cassette,
you can use the Blank Search Function (p. 24) to find
the position where you want to continue recording.
• If a new Cassette is inserted, rewind to the beginning
of the tape before starting recording.
• When inserting the cassette, make sure it faces in
the right direction and then push it in until it stops.
• When the Cassette Holder is in action, do not touch
anything except the [PUSH] mark.
Because the medium is protected by a copy
guard, images cannot be recorded correctly.
INCORRECT OPERATION:
The Recording Start/Stop Button was pressed
without connecting the USB cable to the PC in
Picture Playback Mode.
CANNOT USE USB
CHANGE MODE:
• When closing the Cassette Compartment Cover,
do not get anything caught in the cover, such as
a cable of an optional stereo microphone (For
PV-GS14/PV-GS15).
The USB cable is connected to the Camcorder in
Card Recording Mode or Picture Playback Mode.
CANNOT OPERATE:
You are attempting to record pictures on a Card
while connecting the USB cable to the Camcorder
in Tape Recording/Playback Mode.
Alarm Sounds
When [BEEP SOUND] on the [INITIAL] Sub-Menu on
the [TAPE RECORDING MENU] is set to [ON],
confirmation/alarm beeps are issued as follows.
1 Beep
UNABLE TO WRITE
(MULTI RECORDING):
The [PHOTO SHOT] Button is pressed when you
are recording pictures on a Tape while setting the
Digital Effect [MULTI] of [EFFECT1].
• When you start recording
• When you switch the [OFF/ON] Switch from [OFF] to
[ON]
UNABLE TO WRITE:
The Recording Start/Stop Button is pressed when
you are recording still pictures on the Card.
2 Beeps
• When you pause recording
2 Beeps 4 times
CASSETTE DOOR OPENED:
• If you perform a wrong operation before or during
recording.
Close the Cassette Compartment Cover before
recording.
NO TITLE:
Recording Check
Titles are not recorded.
• For Recording Check, the recording speed mode
(SP/LP) must be the same as the mode used for
the recording. If different, playback images will be
distorted.
UNABLE TO WRITE
(WIDE MODE):
You are attempting to record pictures of S1 signal
(with aspect ratio 16:9) by pressing the [PHOTO
SHOT] Button.
Recording on a Card
• Even if the [SHTR EFFECT] is set to [ON], the
Shutter Effect cannot be recorded on the picture.
• When the color of the screen changes or blurs,
adjust the shutter speed manually to 1/60 or 1/100.
Photoshot
FILE LOCKED:
You are attempting to erase protected files.
CARD LOCKED:
The write protection switch on the SD Memory
Card is set to [LOCK].
• Photoshot Recording results in slightly inferior image
quality.
DISCONNECT USB CABLE:
You are attempting to turn the Mode Dial or turn
the Camcorder off in PC Mode while connecting
the USB cable to the Camcorder.
RapidFire Consecutive Photoshot
• One more still picture may be recorded after you
release the [PHOTO SHOT] Button.
• The RapidFire Consecutive Photoshot and Title
Function cannot be used simultaneously.
61
Others
• When the [SELF TIMER] is set to [ON], the
Camcorder records the maximum number of
recordable pictures depending on the [BURST
MODE] setting.
• When using a card formatted by other equipment,
intervals between recorded pictures may become
large.
• If you repeatedly record or erase pictures, intervals
between recorded pictures may become large. In
this case, back up your important data on a PC, and
format your card using this Camcorder.
Self-timer Recording
• When [BEEP SOUND] on the [INITIAL] Sub-Menu
is set to [ON], the beep sound will be emitted along
with the Recording Lamp flashing in the Self-timer
Standby Mode.
• By operating the [OFF/ON] Switch, Recording
Start/Stop Button or Mode Dial, the Self-timer
Standby Mode is canceled.
Zoom In/Out Functions
• When you are zooming in on a faraway subject, a
sharper focus is achieved if the recording subject is
4 feet (1.2 meters) or further from the Camcorder.
Recording with the Built-in LED Video
Light
Zoom Microphone Function
• The Zoom Microphone Function may not work
effectively if the surrounding noise is too loud.
• It does not work with the external microphone (For
PV-GS14/PV-GS15).
• The subject should be within 4.9 feet (1.5 metres) of
the Camcorder.
• Using the LED Video Light reduces battery time.
• Set the LED Video Light to off when not in use.
• Do not look directly into the light.
Digital Zoom Functions
• As the magnification of digital zoom increases, the
quality of image may deteriorate.
• White balance cannot be set in the digital zoom
range.
• If the LED Video light is used with a Conversion
lens attached, a slight vignetting (darkening around
edges) effect occurs on the screen.
• Using the MagicPix Function at the same time will
make conditions even brighter.
• The Video Light brightens images recorded in a
dimly-lit place, however we recommend using it in a
bright place in order to obtain high quality images.
Image Stabilizer Function
• The Image Stabilizer Function does not operate in
a dimly lit place. In this case, the [EIS] Indication
flashes.
Quick Start
• During the Quick Start Standby Mode, a minute
amount of electricity is consumed.
• Under fluorescent lighting, image brightness may
change or colors may not look natural.
• After-images may appear.
• When a tripod is used, it is recommended that you
turn the Image Stabilizer off.
• Within the digital zoom range, or when recording
with a conversion lens attached, the Image Stabilizer
Function may not work effectively.
• When the Camcorder is left in the Recording Pause
Mode for 5 minutes, it will be turned into the Quick
Start Standby Mode. To turn the Camcorder on
again, set the [OFF/ON] Switch to [OFF] and then
set it to [ON] again. (The Quick Start Mode will be
restored.)
• This Function is not activated in the following case:
• Neither a card nor a tape has been inserted while
the Tape/Card Recording Mode is set.
• In the following cases, Quick Start is canceled during
the Quick Start Standby Mode.
Backlight Compensation Function
• When setting the Iris manually, the Backlight
Compensation Function does not work.
• By operating the [OFF/ON] Switch, the Backlight
Compensation Function is canceled.
• Operate the Mode Dial
• The Battery is replaced
MagicPix Function
• If the [QUICK START] Button is pressed and held
for approximately 2 seconds during the Quick
Start Standby Mode, the Lamp will go off and the
Camcorder will be turned off.
• In a bright place, such as outdoors, the recorded
picture may become whitish.
• In a dark place, the recorded picture is presented in
a time-lapse-like manner.
• If the Camcorder is not operated for approximately
30 minutes when the Quick Start Recording Lamp
lights, the Lamp will go off and the Camcorder will be
completely turned off.
• In the Automatic White Balance Mode, the color
may be recorded unnaturally at the beginning of the
recording.
• The zoom magnification differs from when it is in the
Quick Start Standby Mode and when the recording
starts.
• Adjust the Focus manually.
• The Progressive Photoshot Function is automatically
turned off.
• The RapidFire Consecutive Photoshot Function
cannot be used.
• White Balance cannot be set.
• The shutter speed cannot be adjusted.
• The Image Stabilizer, Program AE, Multi Title Screen,
or Digital Effect Modes in [EFFECT1] cannot be set.
• When recording with the MagicPix Function, it is
recommended that you use a tripod.
62
Others
• The MagicPix Function makes the signal charging
Low Light Mode
time of CCD longer up to 30 times longer than usual,
so that dark scenes that are invisible to the naked
eyes can be recorded brightly. For this reason, a
bright dots may be seen, but this is not a malfunction.
• The Image Stabilizer Function does not work. In this
case, the [EIS] Indication flashes.
• Extremely dark scenes may not be able to be
made brighter to a satisfactory degree.
Spotlight Mode
• With this mode, recorded images may become
extremely dark.
• If the subject is extremely bright, its recorded
image may becomes whitish.
Surf & Snow Mode
• The Soft Skin Function and the Backlight
Compensation Function cannot be changed.
• If the subject is extremely bright, its recorded
image may turn out to be whitish.
Wind Noise Reduction Function
• It does not work with the microphone on an external
microphone.
• When it is set to [ON], directivity of microphone
is regulated depending on the strength of wind to
reduce wind noise.
White Balance
In the following cases, you cannot change
White Balance:
• When you set [EFFECT2] to [SEPIA] or to [B/W].
• When you set the Zoom higher than 20X
(PV-GS9/PV-GS12)/ 22X (PV-GS14)/24X (PV-GS15)
• During Digital Still Picture Mode
• When you display a Menu
Cinema Function
• Using the Cinema Mode does not widen the
recording angle.
• When images are displayed on a TV screen, the
Date/Time Indication may be erased in some cases.
• Depending on the TV, the picture quality may be
deteriorated.
• When you use the MagicPix Mode
In the following cases, the [
] Indication
flashes:
• The Cinema Mode is canceled when a Title is
displayed.
• The Cinema Mode and the Title Creation cannot be
used simultaneously.
• Using the Cinema Mode deactivates [MULTI] and
[P-IN-P] of [EFFECT1].
• The flashing indicates that the previously adjusted
White Balance setting is still set. This setting will be
kept until White Balance is adjusted again.
• You may not be able to achieve correct White
Balance Adjustment manually under weak
illumination.
• Depending on the software in use, the imported
Cinema picture may not be displayed correctly.
Manual Shutter Speed Adjustment
• You may see vertical lines of light in the playback
image of a brightly shining subject or highly reflective
subject.
• During normal playback, movement in the images
may not look smooth.
Program AE
• If any of the Program AE Modes are selected, you
cannot adjust the shutter speed (p. 32) or iris
(p. 32).
• Using the MagicPix Function cancels any of the
Program AE modes.
• Using the Light Function cancels any of the Program
AE modes.
Sports Mode
• During normal playback, the image movement
• Because the color and brightness of the playback
image may become unstable, avoid recording under
fluorescent light, mercury light or sodium light.
• If you are using MagicPix Mode (p. 29) or Program
AE Mode (p. 30), you cannot adjust the shutter
speed.
may not look smooth.
Manual Iris Adjustment
• Depending on zoom magnification, there are iris
values that will not be displayed.
• If you are using MagicPix Mode (p. 29) or Program
AE Mode (p. 30), you cannot adjust the iris.
• If you attempt to adjust the Shutter Speed after
setting the Iris, the value set for the Iris will be
canceled.
• Because the color and brightness of the playback
image may change, avoid recording under
fluorescent light, mercury light or sodium light.
• If you record a subject illuminated with strong light
or a highly reflective subject, vertical lines of light
may appear.
• If the light is insufficient, the [
flashes.
] Indication
Digital Effect Functions
Sports Mode/Portrait Mode
• If you have set [EFFECT2] to [B/W] or [SEPIA],
changing the selected White Balance Mode is not
possible. (pp. 30-31)
• Setting the Cinema Mode cancels the
Picture-in-Picture Mode and the Multi-Picture Mode.
• During the Digital Still Picture Mode, the Digital Effect
Functions cannot be set.
• If you record a still picture in Progressive
Photoshot Mode, the brightness and hue of the
recorded still picture may become unstable.
• If this mode is used for indoor recording, playback
images may flicker.
63
Others
In the following cases, using the [EFFECT1] on
Index Search Functions
• Index Search may not be possible at the beginning
of the tape.
• Scene Index Search may not function properly if the
interval between 2 scene index signals is less than 1
minute.
the [DIGITAL] Sub-Menu is not possible.
• When the MagicPix Mode and Light are set
(pp. 26, 29)
In the following cases, using the Digital Effect
Function is not possible.
• Title in
Multi-Picture Mode
Playback Zoom Function
• You cannot adjust the sound volume with the Remote
Control in Playback Zoom Mode.
• If you turn off the Camcorder power or if you operate
the Mode Dial, Playback Zoom Mode is automatically
canceled.
• Even if Playback Zoom Functions are being used,
images that are output from the DV Terminal (p. 13)
are not enlarged.
• As you enlarge an image, the quality of the image
deteriorates.
• If the [MULTI] Button is pressed while self-recording
Mirror Mode (p. 26) is used, the still picture is
displayed from the upper right corner of the screen,
but, in reality, the picture is recorded from the upper
left corner as usual.
• The quality of Multi images deteriorates slightly.
• The top and bottom of the Multi pictures will be cut
off slightly.
Picture-in-Picture Mode
• If Mode Dial is operated, the smaller picture
disappears.
• Titles cannot be inserted into the smaller picture.
Wipe Mode and Mix Mode
• During a Playback Zoom, the Variable Speed Search
Function cannot be changed with the Remote
Control.
Playback Digital Effect Functions
• Signals of images to which digital effects are added
during playback cannot be output from the DV
Terminal (p. 13).
If one of the following operations are carried out,
stored images will be erased, and Wipe and Mix
Functions cannot be used.
• Set another Digital Effect item
• You cannot use the Wipe or Mix Function while
playing back the non-recorded portion of tape.
• Operate the [OFF/ON] switch or Mode Dial
• Insert or eject a cassette
Playing Back a Card
Playing Back
• If a blank (nothing recorded) Card is played, the
screen becomes white.
Repeat Playback
If you continue to press the [►] Button for 5 seconds
or longer, the Camcorder switches to Repeat Playback
Mode, and the [R ] Indication appears. (To cancel
Repeat Playback Mode, set the [OFF/ON] Switch to
[OFF].)
Listening to Playback Sound through
Headphones
If you want to use the headphones to listen to the
playback sound, set [AV JACK] on the [INITIAL]
Sub-Menu to [OUT/PHONES] and connect the
headphones to the [PHONES] Jack (p. 13) on the
Camcorder. In this case, no sound (including warning
and shutter sounds) will be reproduced through the
built-in speaker of the Camcorder.
Choosing Sound during Playback
You can select the sound by using the [AUDIO OUT]
setting on the [PLAYBACK] Sub-Menu.
STEREO: Stereo Sound (main sound and sub
sound)
• If you attempt to play back a file recorded in a
different format or if file data is defective, the whole
display becomes bluish and the [UNPLAYABLE
CARD] Indication may appear as warning.
• When playing back a picture recorded on other
equipment, its size and that of this Camcorder may
appear differently.
• When playing back a picture recorded on other
equipment, the picture may not be played back or
the quality of pictures may be deteriorated.
• When playing back a non standardized file, the
Folder File Number may not be displayed.
• In the following cases, black bars may appear,
depending on the playback device.
• When playing back a mega-pixel still-picture with
this Camcorder and recording it onto a tape
• Changing the picture size to 640 x 480 pixels with
DV STUDIO
L:
R:
Left channel sound (main sound)
Right channel sound (sub sound)
Slide Show
• Playback time may take longer than usual depending
on the picture.
• If you dub a tape recorded at the [12bit] selected as
the [AUDIO REC] on the [RECORDING] Sub-Menu,
playback sound becomes stereo sound regardless of
the [AUDIO OUT] setting if [12bit AUDIO] is set to [MIX].
64
Others
Creating a Title
Recording Pictures from a Card onto a
Tape
• Even if the contrast of the Title is adjusted, the
portions where there is little difference between light
and dark and where the boundary between light and
dark is unclear may not appear.
• The Title may not be clear if something small is used
for it.
• If titles are created, the number of images that can
be recorded on a Card decreases.
• If the number of images that can be recorded on a
Card is small, you may not be able to create a title.
• When recording the Card Image on a Tape, its size
is transformed into 720 x 480 pixels according to the
DV format.
• If you attempt to record a still picture with a large
image size on a Tape, there may be a reduction in
the quality of the image.
Audio Dubbing
• The blank section of a tape cannot be dubbed.
• Sounds sent through the DV terminal cannot be
dubbed.
Adding a Title
• The Title In Function and Digital Effects cannot be
used simultaneously.
• The Title In Function and RapidFire Consecutive
Photoshot cannot be used simultaneously.
• When a title is displayed in Tape Playback Mode, the
title is not output from the DV Terminal.
• The Multi-Picture Mode cannot be used once the title
is inserted.
• If a tape has a non-recorded portion when the tape is
dubbed, images and sounds may be disturbed when
this portion of the tape is played back.
• If you set the tape counter back to 0 at the position
where you want to stop Audio Dubbing so as to
make it possible to use the Memory Stop Function
(p. 71), Audio Dubbing is terminated automatically
when the tape reaches this position.
• A full-colored title made on other equipment cannot
be played back or added to the picture with this
Camcorder.
• A title with a size than 640 x 480 pixels cannot be
displayed.
• When the title is displayed on the Multi screen, the
recording and the playback cannot be performed.
• During DV input, you cannot use Title In Function
or display titles on the Multi screen. Select the
desired titles to display them on the screen before
connecting the DV cable to the Camcorder.
• In the case of importing data recorded with Audio
Dubbing to a PC using the PC’s software, only the
original sound (ST1) may be imported, depending on
the software.
Using the DV Cable for Recording
(Digital Dubbing)
• Regardless of the setting, digital dubbing is carried
out automatically in the same audio recording mode
as that of the playback Cassette.
• The images on the recorded monitor may be
disturbed, but it does not affect the recorded images.
• Even if Playback Digital Effects, Playback Zoom, or
Playback Title In have been used, these effects are
not output from the DV terminal.
• Even if you use a device equipped with DV
Terminals, you may not be able to perform Digital
Dubbing in some cases.
• Date or other information to be displayed cannot be
displayed if the software of the connected equipment
does not support the display function.
DPOF
• Perform the DPOF Settings with your Camcorder.
• Verifying the DPOF Settings may take a little time.
Wait until the Card Access Lamp goes out.
Lock Setting
• The Lock Setting carried out by this Camcorder is
only effective for this Camcorder.
• The SD Memory Card has a write protection switch
on it. If the switch is moved to the [LOCK] side, you
cannot write to or format the Card. If it is moved
back, you can.
Cautions for Use
Playing Back on Your TV
After Use
• Depending on your TV, nothing may be shown even
if you correctly connect the Camcorder with your
TV. In this case, set [AV JACK] on the [INITIAL]
Sub-Menu to [OUT].
1 Take out the Cassette. (p. 17)
2 Set the [OFF/ON] Switch to [OFF].
3 Take out the Card. (p. 18)
• Picture size may be displayed differently when
playing back a Cinema picture on a wide-screen TV
with Playback Digital Effect.
4 Detach the power supply and retract the
Viewfinder or the LCD Monitor. (pp. 15-16, 19)
5 To protect the Lens, attach the supplied Lens
Cap.
65
Others
Do not use benzine, thinner or alcohol for
cleaning the Camcorder.
• The Camcorder body may be deformed and the
surface finish may peel off.
• Before cleaning, detach the Battery or pull out the
AC Cable from the AC Jack.
• Wipe the Camcorder with a soft dry cloth. To remove
stubborn stains, wipe with a cloth that is soaked in
a detergent diluted with water and afterwards finish
wiping with a dry cloth.
Cautions for Use
When you use your Camcorder on a rainy or
snowy day or on a beach, make sure that no
water enters the Camcorder.
• Water may cause the Camcorder or Cassette to
malfunction. (Irreparable failure may occur.)
• If sea water splashes onto the Camcorder, wet a
soft cloth with tap water, wring it well, and use it to
wipe the camera body carefully. Then, wipe it again
thoroughly with a soft dry cloth.
• For storing or transporting the Camcorder, place it in
a bag or case lined with soft pads so as to prevent
the coating on the camera body from being worn.
After use, be sure to take the Cassette out and
detach the Battery from the Camcorder or pull
out the AC Cable from AC Jack.
• If the Cassette is left in the Camcorder, the tape sags
and deteriorates.
• If the Battery is left on the Camcorder for a long time,
the voltage drops excessively, and the Battery will
not function even after it is recharged.
Keep the Camcorder away from magnetized
equipment (such as a microwave oven, TV,
video game equipment, etc.).
• If you use the Camcorder on or near a TV, images
or sounds may be disturbed due to electromagnetic
wave radiation.
• Do not use near a cell phone because doing so
may cause noise to adversely affect the picture and
sound.
• Recordings on the tape may be damaged, or images
may be distorted, by strong magnetic fields created
by speakers or large motors.
About AC Adaptor
• Electromagnetic wave radiation generated by a
microprocessor may adversely affect the Camcorder,
causing the disturbance of images and sounds.
• If the Camcorder is affected by magnetically charged
equipment and does not function properly, turn off
the Camcorder power and detach the Battery or AC
Adaptor and then connect the Battery or AC Adaptor
again. Thereafter, turn on the Camcorder power.
Do not use your Camcorder near radio
transmitters or high-voltage cables.
• If you record pictures near radio transmitters or
high-voltage cables, recorded images or sounds may
be adversely affected.
• If the temperature of the Battery is extremely high or
extremely low, the [CHARGE] Lamp may continue
flashing, and the Battery may not be charged. After
the temperature of the Battery has decreased or
increased sufficiently, charging starts automatically.
If the [CHARGE] Lamp continues to flash even after
the Battery temperature has decreased or increased
sufficiently, the Battery or AC Adaptor may be faulty.
In this case, please contact a dealer.
• If the Battery is warm, charging takes a longer time
than normal.
• If you use the AC Adaptor near a radio, radio
reception may be disturbed. Keep the AC Adaptor 3
feet (1 meter) or more away from radio.
Do not use this Camcorder for surveillance
purposes or other business use.
• When using the AC Adaptor, it may generate whirring
sounds. However, this is normal.
• After use, be sure to pull out the AC Cable from the
AC Jack. (If they are left connected, a minute amount
of current is consumed.)
• If you use the Camcorder for a long period of
time, the internal temperature increases and,
consequently, this may cause malfunction.
• This Camcorder is not intended for business use.
When you use your Camcorder on a beach or
similar place, do not let sand or fine dust get
into the Camcorder.
• Sand or dust may damage the Camcorder or
Cassette. (Care should be taken when inserting and
removing the Cassette.)
Do not spray insecticides or volatile chemicals
onto the Camcorder.
• If the Camcorder is sprayed with such chemicals,
the camera body may be deformed and the surface
finish may peel off.
• Keep the electrodes of the AC Adaptor and Battery
always clean.
Condensation
If you turn the Camcorder on when condensation
occurs on the head or the tape, Condensation
Indication [
DEW ] (yellow or red) blinks on the
Viewfinder or the LCD Monitor and the messages [DEW
DETECTED] or [EJECT TAPE] (only when the tape is
inserted) appear. In this case, follow the procedure
below.
Blinking in yellow:
Dew is slightly adhering to the head or the tape.
• Do not keep rubber or plastic products in contact with
the Camcorder for a long period of time.
Blinking in red:
Dew has adhered to the head or the tape.
66
Others
1 Remove the tape if it is inserted.
• It takes about 20 seconds to open the Cassette
Holder. This is not a malfunction.
4 If the image is not still clear, repeat Steps 1
to 3. (Do not use the Head Cleaner 3 times or
more consecutively.)
Notes:
2 Leave the Camcorder with the Cassette
Compartment Cover closed to cool or warm
it to the ambient temperature.
• Do not rewind every time you use the Head Cleaner.
Rewind only when the tape reaches the end, and
then use it again from the beginning in the same
manner as before.
• If the heads become dirty soon after cleaning, the
tape may be damaged. In this case, immediately
stop using that Cassette.
• Do not clean the heads excessively. (Excessive
cleaning may cause excessive wear of the heads. If
the heads are worn, images cannot be played back
even after the heads are cleaned.)
• If the dirty heads cannot be cleaned with the Head
Cleaner, the Camcorder needs to be cleaned at a
Servicenter. Please consult a dealer.
When [
DEW ] blinks in yellow
• You cannot use the Tape Recording/Playback
Mode. Leave the Camcorder for about 30 minutes.
• However, you can use the Card Recording Mode
or Picture Playback Mode when the cassette is
not inserted.
When [
DEW ] blinks in red
• The Power Indicator Lamp blinks for about 1
minute and then the Camcorder automatically
turns off. Leave it for about 2 to 3 hours.
3 Turn the Camcorder on again, set it to the
Tape Recording/Playback Mode and then
check if the condensation indication
disappears.
• Head cleaning due to dirty heads is not considered
a malfunction of the product. It is not covered by the
warranty.
Periodical Check-up
Especially in cold conditions, dew may be frozen. In
this case, it may take more time before the
condensation indication disappears.
Watch for Condensation even before the
Condensation Indication is displayed.
• The condensation indication may not appear
depending on circumstances. When condensation
occurs on the lens or the Camcorder, it also may
occur on the head and the tape. Do not open the
Cassette Compartment Cover.
To maintain the highest image quality, we recommend
replacement of worn parts, such as heads, etc., after
approximately 1000 hours of use. (This, however,
depends on operating conditions, such as temperature,
humidity, dust, etc.)
Optimal Use of the Battery
Battery Characteristics
This Battery is a rechargeable lithium ion battery. Its
ability to generate power is based upon the chemical
reaction that takes place inside it. This reaction is
susceptible to the surrounding temperature and humidity,
and, if the temperature is too high or too low, the
operating time of the Battery becomes shorter. If the
Battery is used in an extremely cold environment, the
Battery may operate only for about 5 minutes. If the
Battery becomes extremely hot, a protective function
may operate, and the Battery may become unusable
for a while.
Be Sure to Detach the Battery after Use
Be sure to detach the Battery from the Camcorder. (If
it is left attached to the Camcorder, a minute amount
of current is consumed even when the Camcorder
power is off.) If the Battery is left attached to the
Camcorder for a long time, over-discharge takes
place. The Battery may become unusable after it is
charged.
When the Lens Is Fogged:
Set the [OFF/ON] Switch to [OFF] and leave the
Camcorder in this condition for about 1 hour. When the
lens temperature becomes close to the ambient
temperature, the fog disappears naturally.
Video Head Clogging and Care
If the heads (the parts that make contact with the tape)
are dirty, mosaic-pattern noise may appear on the
playback image, or the screen as a whole becomes
black. If the heads are extremely dirty, recording
performance deteriorates, and, in the worst case, the
Camcorder cannot record at all.
Causes of Dirty Heads
• Large quantity of dust in the air
• High-temperature and high-humidity environment
• Damaged tape
Disposing of an Unusable Battery
• Long operating hours
• The Battery has a limited life.
• Do not throw the Battery into fire because it may
cause an explosion.
Always Keep the Terminals of the Battery Clean
Prevent the terminals from getting clogged with dirt,
dust, or other substances. If you drop the Battery
accidentally, check to see if the Battery body and
terminals are deformed. Attaching a deformed Battery
to the Camcorder or AC Adaptor may damage the
Camcorder or AC Adaptor.
Using Panasonic cleanig cassette (AY-DVMCLA)
1 Insert the Head Cleaner into the Camcorder
in the same manner as a Video Cassette.
2 Press the [►] Button, and approximately 20
seconds later, press the [ ] Button. (Do not
rewind the tape.)
3 Take out the Head Cleaner. Insert a Video
Cassette and start recording. Then, play the
tape back to check the recorded image.
67
Others
Card
Cautions for Storage
• When the Card is being read, do not remove the
Card, turn off the power, or subject it to vibration or
impact.
• Do not leave the Card in places where there is
high temperature or direct sunlight, or where
electromagnetic waves or static electricity are easily
generated.
• Do not bend or drop the Card. The Card or the
recorded content may be damaged.
• After use, be sure to remove the Card from the
Camcorder.
• After usage, store the supplied SD Memory Card in
the enclosed bag.
Before storing the Camcorder, take the
Cassette out and detach the Battery.
Store all the components in a dry place with a
relatively stable temperature.
(Recommended Temperature: 59 °F to 77 °F (15 °C to
25 °C), Recommended Humidity: 40 % to 60 %)
Camcorder
• Wrap it with a soft cloth to prevent dust from getting
into the Camera.
• Do not leave the Camcorder in places that expose it
to high temperature.
Battery
• Extremely high temperatures or low temperatures
will shorten the life of the Battery.
• Do not touch the terminals on the back of the Card
with your fingers. Do not allow dirt, dust or water to
enter it.
• Keep the Memory Card out of reach of children to
prevent swallowing.
• If the Battery is kept in smoky or dusty places, the
terminals may rust and cause malfunctions.
• Do not allow the Battery terminals to come in
contact with metal objects (such as necklaces,
hairpins, etc.). This can result in a short circuit or
heat generation and, if you touch the Battery in
this condition, you may be badly burned.
• Store the Battery in a completely discharged state.
To store the Battery for a long period of time, we
recommend you charge it once every year and store
it again after you completely use up the charged
capacity.
LCD Monitor/Viewfinder/Lens Hood
LCD Monitor
• In a place with drastic temperature changes,
condensation may form on the LCD Monitor. Wipe it
with a soft dry cloth.
• If your Camcorder is extremely cold when you turn its
power on, the image on the LCD Monitor is slightly
darker than usual at first. However, as the internal
temperature increases, it goes back to the normal
brightness.
Cassette
• Before storing it, rewind the tape to the beginning.
If the Cassette is left for more than 6 months with
the tape stopped midway, the tape sags (although it
depends on the storage condition). Be sure to rewind
to the beginning.
• Store the Cassette in its case. Dust, direct sunlight
(ultraviolet rays), or humidity may damage the tape.
Dust contains hard mineral particles, and dusty
Cassettes damage the heads of the Camcorder and
other components. Develop a habit of returning the
Cassette back to its case.
• Once every half year, wind the tape to the end and
then rewind it to the beginning. If the Cassette is left
for 1 year or longer without winding or rewinding,
temperature and humidity changes may cause the
Cassette to deform due to swelling, shrinking, and so
forth. The wound tape may stick to itself.
• Do not place a Cassette near highly magnetic
substances or equipment.
• The surface of tape is covered with extremely minute
magnetic particles, upon which signals are recorded.
Magnetic necklaces, toys, etc., have magnetic force
that is stronger than you may normally expect, and
they may erase the contents of a recording or may
cause noise in images and sounds.
Extremely high precision technology is employed to
produce the LCD Monitor screen featuring a total of
approximately 105,000 pixels. The result is more
than 99.99 % effective pixels with a mere 0.01 % of
the pixels inactive or always lit. However, this is not
a malfunction and does not affect the recorded
picture.
Viewfinder
• Do not direct the Viewfinder or Lens to the sun.
Internal components may be seriously damaged.
•
When the Camcorder is used with a large capacity
Battery (CGR-D16A/1B, CGP-D28A/1B: Optional)
attached to it, it is not practical to look in the Viewfinder
from behind the Battery.
Extremely high precision technology is employed to
produce the Viewfinder screen featuring a total of
approximately 67,000 pixels (PV-GS9/PV-GS12)/
113,000 pixels (PV-GS14/PV-GS15). The result is
more than 99.99 % effective pixels with a mere 0.01
% of the pixels inactive or always lit. However, this
is not a malfunction and does not affect the
recorded picture.
68
Others
Lens Hood
• Do not attach other conversion lenses in front of
the Lens Hood; there is no mount to be used for the
attachment.
Recording does not start although power is
supplied to the Camcorder and the
Cassette is correctly inserted.
• Is the accidental erasure prevention slider on
the Cassette open? If it is open (set to [SAVE]),
recording cannot be performed. (p. 17)
• Is the tape wound to the end? Insert a new
Cassette. (p. 17)
• When you wish to attach the Tele Conversion Lens (not
supplied), Wide Conversion Lens (not supplied), MC
Protector (not supplied), or ND Filter (not supplied),
first of all, turn the Lens Hood counter-clockwise. If
the MC Protector or ND Filter is used, the Lens Hood
can be mounted on the filter.
• If you push the [W/T] Lever toward [W] during
recording with the filter and conversion lens
attached together to the Camcorder, 4 corners of the
image may become dark (vignetting). For details,
please refer to the operating instructions of your
accessories.
• Is the Camcorder power turned on? (p. 24)
• Has condensation occurred? Wait until the
Condensation Indication disappears. (pp. 66-67)
Auto Focus Function does not work.
• Is Manual Focus Mode selected? If Auto
Focus Mode is selected, focus is automatically
adjusted. (pp. 32, 71)
• There are some recording subjects and
recording surroundings for which the Auto Focus
Function does not operate correctly. In this case,
use the Manual Focus Mode to adjust the focus.
(p. 32)
• Be sure to keep the Lens Hood attached to the
Camcorder so as to shut out unnecessary light.
Before Requesting Service (Problems
and Solutions)
Audio dubbing cannot be performed.
• Is the accidental erasure prevention slider on
the Cassette open? If it is open (set to [SAVE]),
recording cannot be performed. (p. 17)
• Are you attempting to edit a tape portion that
was recorded in LP Mode? LP Mode does not
allow audio dubbing to operate. (p. 23)
The Camcorder power cannot be turned on.
• Is the power source connected correctly?
(pp. 15-16)
The Camcorder power is turned off
automatically.
• When the Recording Pause Mode continues
for more than 5 minutes, the power is turned
off automatically for tape protection and power
conservation. (If the AC Adaptor is used, the
power is turned off only when the tape is
inserted in Tape Recording Mode.) When the
tape is inserted in Tape Recording Mode and
if the Recording Pause Mode continues for
more than 5 minutes the power is turned off
automatically. To resume recording from this
condition, turn off, then turn on the power again.
(pp. 24-25)
The Time Code becomes inaccurate.
• The Time Code Indication counter may not be
constant in the reverse direction in Slow Motion
Playback Mode, but this is not a malfunction.
The Remaining Tape Time Indication does
not match the actual remaining tape time.
• If scenes of less than 15 seconds are
continuously recorded, the remaining tape time
cannot be displayed correctly.
• In some cases, the Remaining Tape Time
Indication may show remaining tape time that is
2 to 3 minutes shorter than the actual remaining
tape time.
The Camcorder power does not stay on
long enough.
• Is the Battery low? Charge the Battery or attach
Pictures cannot be played back even when
the [►] Button is pressed.
a fully charged Battery. (p. 15)
• Is the Mode Dial set to Tape Playback Mode? If
not, the playback function cannot be used.
(p. 35)
• Has condensation occurred? Wait until the
Condensation Indication disappears. (pp. 66-67)
Battery runs down quickly.
Mosaic-pattern noise appears on images
during Cue, Review or Slow Motion
Playback.
• This phenomenon is characteristic of digital
video systems. It is not a malfunction.
• Is the Battery fully charged? Charge it with the
AC Adaptor. (p. 15)
• Are you using the Battery in an extremely cold
place? In cold places, the operating time of the
Battery becomes shorter. (p. 68)
• Has the Battery worn out? If the operating time
is still too short even after the Battery is fully
charged, the Battery has worn out.
The Battery cannot be charged.
• If the DC Cable is connected to the AC Adaptor,
charging cannot be performed. Disconnect the
DC Cable.
69
Others
Although the Camcorder is correctly
connected to a TV, playback images cannot
be seen.
• Have you selected “Video Input” on the TV?
Please read the operating instructions of your
TV and select the channel that matches the
input jacks used for the connection.
Recorded pictures are not clear.
• Is [PICT QUALITY] on the [CARD] Sub-Menu
set to [NORMAL] or [ECONOMY]? If recording
is done with it set to [NORMAL] or [ECONOMY],
images with fine details may include a
mosaic-like pattern. Set [PICT QUALITY] to
[FINE]. (p. 25)
• Depending on your TV, nothing may be shown
even if you correctly connect the Camcorder
with your TV. In this case, set [AV JACK] on the
[INITIAL] Sub-Menu to [OUT].
Photoshot Playback images do not look
normal.
• The picture may be damaged. In order to
prevent the loss of image data, backing up
on a Cassette or a personal computer is
recommended. (pp. 44, 48)
Playback picture is not clear.
• Are the heads of the Camcorder dirty? If the
heads are dirty, playback image cannot be clear.
(p. 67)
During Playback the [UNPLAYABLE CARD]
Indication is displayed.
Playing back or recording do not function,
the screen has frozen or the indication has
disappeared.
• Turn the Camcorder off. If the Camcorder is
not turned off after operating the [OFF/ON]
switch, press the [RESET] Button (p. 12) first.
And detach the Battery or AC Adaptor and then
reattach it.
• The image was either recorded in a different
format, or data is damaged.
Even if a Card is formatted, it cannot be
used.
• Either the Camcorder or the Card may be
damaged. Please consult a dealer.
The Camcorder clatters when shaking it.
• It is a sound of the lens moving, not a
malfunction.
Sound is not played back from the built-in
speaker of the Camcorder or the
headphones.
• Is the volume too low? During playback, push
the [W/T] Lever to display the [VOLUME]
Indication and adjust the volume. (p. 35)
When the USB Cable is disconnected, an
error message will appear on PC.
• To disconnect the USB cable safely, double-click
the [
] icon in the task tray and follow the
instructions on the screen. (p. 49)
Different sounds are reproduced at the
same time.
Using the RESET button
• [12bit AUDIO] on the [PLAYBACK] Sub-Menu of
the [TAPE PLAYBACK MENU] has been set to
[MIX]. As a result, the original sound and sound
that was recorded by audio dubbing are played
back together. It is possible to reproduce the
sounds separately. (p. 44)
1 Open the LCD Monitor. (p. 19)
2 Undo Grip Belt end 1 and pull Lens Cap
Cord 2 downward to loosen Grip Belt.
The original sound was erased when audio
dubbing was performed.
• If you perform audio dubbing on a recording
made in [16bit] Mode, the original sound will
be erased. If you wish to preserve the original
sound, be sure to select [12bit] Mode at the time
of recording.
1
2
3 Use projection 3 on the Lens Cap to press
the [RESET] Button 4 .
Sounds cannot be played back.
• Although a Cassette with no audio dubbing is
being played, is [12bit AUDIO] on the [PLAYBACK]
Sub-Menu of the [TAPE PLAYBACK MENU] set
to [ST2]? To play back a Cassette with no audio
dubbing, [12bit AUDIO] must be set to [ST1].
(p. 44)
4
3
• Is the Variable Speed Search Function working?
Press the [►] Button to cancel the Variable
Speed Search Function. (p. 36)
70
Others
6) Recording a subject with little contrast
Explanation of Terms
Digital Video System
In a digital video system, images and sounds are
converted into digital signals and recorded on a tape.
This complete digital recording is capable of recording
and playback with minimal image and sound
deterioration.
• Because the Camcorder achieves focus based
upon the vertical lines of an image, a subject with
little contrast, such as a white wall, may become
blurry.
Time Code
Time Code signals are data that indicate time
measured in hours, minutes, seconds, and frames
(30 frames per second). If this data is included in a
recording, an address is assigned to each image on
the tape.
In addition, it automatically records data, such as Time
Code and Date/Time, as digital signals.
Compatibility with S-VHS or VHS Cassettes
Because this Camcorder employs a digital system for
recording image and sound data, it is not compatible
with conventional S-VHS or VHS video equipment that
employs an analog recording system.
The size and shape of the Cassettes are also different.
Compatibility with Output Signals
Because AV signal output from the AV signal output
Jack is analog (the same as conventional video
systems), this Camcorder can be connected with
S-VHS or VHS video or a TV for playback.
• The Time Code is automatically recorded as a part of
the sub-code at each recording.
• When a new (previously unrecorded) Cassette is
inserted, the Time Code automatically starts from
zero. If a recorded Cassette is inserted, the Time
Code picks up from the point where the last scene
was recorded. (In this case, when the Cassette
is inserted, the zero display [0h00m00s00f] may
appear, but the Time Code starts from the previous
value.)
Focus
Auto Focus Adjustment
• The Time Code cannot be reset to zero.
• Unless the Time Code is continuously recorded from
the beginning of a tape, accurate editing may not
be possible. To ensure that the Time Code will be
recorded with no breaks, we recommend the use of
the Blank Search Function (p. 24) before recording a
new scene.
The Auto Focus System automatically moves forward
and backward the focusing lens inside the Camcorder
to bring the subject into focus so that the subject can
be seen clearly.
However, the Auto Focus System does not function
properly for the following subjects or under the
following recording conditions.
Memory Stop Function
The Memory Stop Function is useful for the following
operations.
Please use the Manual Focus Mode instead.
1) Recording a subject whose one end is
located closer to the Camcorder and the
other end farther away from it
• Because Auto Focus makes adjustments at the
center of an image, it may be impossible to focus
on a subject that is located in both foreground and
background.
Rewinding or fast-forwarding a tape to a
desired position
1 Set [DISPLAY] >> [C.DISPLAY] >> [MEMORY].
2 Reset the Tape Counter to zero at the tape
position from which you want to play it back
later. (pp. 14, 21)
3 Start playback or recording.
2) Recording a subject behind dirty or dusty
glass
• Because the focus is on the dirty glass, the
4 After playback or recording has finished:
Set the Camcorder to Tape Playback Mode.
• The [POWER] Lamp lights up.
subject behind the glass will not be focused.
3) Recording a subject in dark surroundings
• Because the light information that comes through
the lens decreases considerably, the Camcorder
cannot focus correctly.
5 Rewind the tape.
• The tape automatically stops approximately at the
position where the counter was set to zero.
Stopping editing automatically during audio
dubbing
4) Recording a subject that is surrounded by
objects with glossy surfaces or by highly
reflective objects
1 Set [DISPLAY] >> [C.DISPLAY] >> [MEMORY].
2 Reset the Tape Counter to zero at the
position where you want to stop editing.
• Because the Camcorder focuses on the objects
with glossy surfaces or on highly reflective objects,
the subject may become blurry.
3 Play back the still picture where you want to
start audio dubbing.
5) Recording a fast-moving subject
• Because the focus lens-inside moves
mechanically, it cannot keep up with the
fast-moving subject.
4 Start audio dubbing. (p. 44)
• Audio dubbing automatically stops at the position
where the counter was set to zero.
71
Others
Mic Input: (For PV-GS14/PV-GS15)
Specifications
Digital Camcorder
Mic sensitivity –50 dB (0 dB=1 V/Pa, 1 kHz)
(Stereo mini jack)
USB:
Information for your safety
Card reader/writer function (For PV-GS12/
PV-GS14/PV-GS15), USB 2.0 compliant
(max. 12 Mbps)
Power Source:
DC 7.2/7.8 V
Power Consumption:
Recording
No copyright protection support
Digital Interface:
DV Input/Output Jack (IEEE1394, 4-pin)
Dimensions:
4.5 W
Recording Format:
Mini DV (Consumer-use Digital Video SD Format)
Tape Used:
6.35 mm digital video tape
Recording/Playback Time:
SP: 80 min.; LP: 120 min. (with DVM80)
Video
Recording System:
Digital Component
Television System:
Approx. 87 (H) x 69 (W) x 112 (D) mm
Approx. 3-3/8 (H) x 2-3/4 (W) x 4-3/8 (D) inch
Weight:
g
Approx. 0.40 k (0.88 lbs.) (PV-GS9/PV-GS12)
g
Approx. 0.41 k (0.90 lbs.) (PV-GS14/PV-GS15)
(without Battery and DV cassette)
Operating Temperature:
32 °F – 104 °F (0 °C–40 °C)
Operating Humidity:
EIA Standard: 525 lines, 60 fields NTSC color
signal
Audio
10 % – 80 %
Card Memory Functions (For PV-GS12/PV-GS14/
PV-GS15)
Recording System:
Recording Media:
PCM Digital Recording
16 bit (48 kHz/2ch), 12 bit (32 kHz/4ch)
Image Sensor:
1/6-inch CCD Image Sensor
Lens:
Auto Iris, F1.8, Focal Length; 2.1-50.4 mm
(PV-GS15) / 2.1-46.2 mm (PV-GS14) / 2.1-42 mm
(PV-GS9/PV-GS12), Macro (Full Range AF)
Filter Diameter:
MultiMediaCard (4 MB/8 MB/16 MB)
SD Memory Card (8 MB/16 MB/32 MB/64 MB/
128 MB/256 MB/512 MB)
Still picture recording file format:
JPEG (Design rule for Camera File system, based
on Exif 2.2 standard), DPOF corresponding
Still Image Size:
640 X 480 pixels (VGA)
WEB Camera
27 mm
Compression:
Zoom:
Motion JPEG
20:1 Power Zoom (PV-GS9/PV-GS12)
22:1 Power Zoom (PV-GS14)
24:1 Power Zoom (PV-GS15)
Monitor:
2.5-inch LCD
Viewfinder:
Color Electronic Viewfinder (PV-GS14/PV-GS15)
Electronic Viewfinder (PV-GS9/PV-GS12)
Microphone:
Stereo
Speaker:
Image Size:
320 X 240 pixels (QVGA)
AC Adaptor
Information for your safety
Power Source:
110/120/220/240 V AC, 50/60 Hz
Power Consumption:
18 W
DC Output:
DC 7.8 V, 1.4 A (Camcorder Operation)
DC 8.4 V, 1.2 A (Battery Charging)
1 round speaker 20 mm
Standard Illumination:
1,400 lx
Minimum Required Illumination:
2 lx (MagicPix Mode)
Dimensions:
70 (W) X 45 (H) X 115 (D) mm
2-3/4 (W) X 1-3/4 (H) X 4-1/2 (D) inch
Weight:
Video Output Level:
1.0 Vp-p, 75 ohm
g
Approx. 0.16 k (0.35 lbs.)
S-Video Output Level: (For PV-GS14/PV-GS15)
Y Output: 1.0 Vp-p, 75 ohm
C Output: 0.286 Vp-p, 75 ohm
Audio Output Level (Line):
316 mV, 600 ohm
Weight and dimensions are approximate values.
Specifications may change without prior notice.
72
Others
Camcorder Accessory System
Accessory #
Figure
Description
Price
PV-DAC11A
AC Adaptor with AC Cable and DC Cable
$119.95
CGR-D08A/1B
CGR-D16A/1B
CGP-D28A/1B
800 mAh/1 h 30 min, Battery Pack
1 600 mAh/3 h, Battery Pack
2 800 mAh/5 h, Battery Pack
$69.95
$99.95
$129.95
CGR-D53A/1K
5 300 mAh/9 h, Battery Pack
$229.95
$55.00
DV Interface Cable (i.LINK)
(4-pin to 4-pin)
PV-DDC9
Call For
Pricing
LSSQ0411
IR Remote Control
RP-SD64BPPA
RP-SD32BPPA
RP-SD16BPPA
64 MB SD Memory Card
32 MB SD Memory Card
16 MB SD Memory Card
Call For
Pricing
USB Reader/Writer for SD Memory Card
(compatible with MultiMediaCard)
BN-SDCAPE/1B
BN-SDABPE/1B
$79.95
SD PCMCIA Adaptor
(compatible with MultiMediaCard)
$79.95
Call For
Pricing
LSFT0577
DV STUDIO 3.1E-SE
USB Cable
Call For
Pricing
K1HA05CD0005
PV-H150
Carrying Case
Carrying Case
$49.95
Call For
Pricing
PV-HB002
• Please refer to page 74, when placing an order.
73
Others
Camcorder Accessory Order Form
Please photocopy this form when placing an order.
1. Camcorder Model #
2. Items Ordered
Accessory #
Description
Price Each
Quantity
Total Price
Subtotal
Your State & Local Sales Tax
Shipping & Handling
Total Enclosed
6.95
3. Method of payment (check one)
Check of Money Order enclosed (NO C.O.D.SHIPMENTS)
VISA
Credit Card #
MasterCard
Discover
Expiration Date
Customer Signature
Make Check or Money Order to: PANASONIC ACCESSORIES
(Please do not send cash)
4. Shipping information (UPS delivery requires complete street address)
Ship To:
Mr.
Mrs.
Ms.
Phone #:
Day
First
Last
(
(
)
)
Street Address
Night
City
State
Zip
TO OBTAIN ANY OF OUR CAMCORDER ACCESSORIES YOU CAN DO ANY OF THE
FOLLOWING:
VISIT YOUR LOCAL PANASONIC DEALER
OR
CALL PANASONIC’S ACCESSORY ORDER LINE AT 1-800-332-5368
[6 AM-5 PM M-F, 6 AM-10:30 AM SAT, PACIFIC TIME]
OR
MAIL THIS ORDER TO: PANASONIC SERVICES COMPANY ACCESSORY ORDER OFFICE
20421 84th Avenue South Kent, WA. 98032
74
Others
Request for Service Notice
Please photocopy this form when making a request for service notice.
In the unlikely event this product needs service.
• Please include your proof of purchase.
(Failure to do so will delay your repair.)
Request for Service Notice: • To further speed your repair, please provide an
explanation of what is wrong with the unit and any
symptom it is exhibiting.
Mail this completed form and your Proof of Purchase along with your unit to:
Panasonic Services Company
1705 N. Randall Road
Elgin, IL. 60123-7847
Attn: Camcorder Repair
75
Others
Limited Warranty
PANASONIC CONSUMER ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC CORPORATION
OF AMERICA
PANASONIC SALES COMPANY, DIVISION OF
MATSUSHITA ELECTRIC OF PUERTO RICO, INC.,
AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
One Panasonic Way Secaucus, New Jersey 07094
Panasonic/Quasar Video Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, Panasonic
Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”)
will, for the length of the period indicated on the chart below, which starts with the date of original purchase
(“warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace
it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.
Product
Camcorder
Parts
Labor
Service
Carry-In or Mail-In
Contact Number
One (1) Year (except CCD
Image Sensor)
CCD Image Sensor - 6 (Six)
Months
Ninety (90) Days
1-800-211-PANA(7262)
Ninety (90) Days
Ninety (90) Days
DVD/VCR Deck,
A/V Mixer
One (1) Year
Carry-In or Mail-In
1-800-211-PANA(7262)
TV/VCR, TV/DVD,
TV/DVD/VCR
Combination
Carry-In: 21” CRT and Smaller
In-Home or Carry-In: 22” CRT 1-800-211-PANA(7262)
and Larger
One (1) Year (except CRT)
CRT - Two (2) Years
Ninety (90) Days
Ninety (90) Days
TV/HDR
Combination
One (1) Year (except CRT)
CRT - Two (2) Years
Ninety (90) Days
Ninety (90) Days
In-Home or Carry-In
1-888-843-9788
Rechargeable
Batteries
(in exchange for
defective item)
Ten (10) Days
Not Applicable
Carry-In or Mail-In
1-800-211-PANA(7262)
Tape
(in exchange for Five (5) Days
defective item)
Not Applicable
Not Applicable
Carry-In or Mail-In
Carry-In or Mail-In
1-800-211-PANA(7262)
1-800-211-PANA(7262)
Memory Cards (in
exchange for
Ninety (90) Days
defective item)
During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no
charge for parts. You must carry-in or mail-in your product or arrange for in-home service, as applicable, during the
warranty period. If non-rechargeable batteries are included, they are not warranted. This warranty only applies to products
purchased and serviced in the United States or Puerto Rico. This warranty is extended only to the original purchaser of a
new product which was not sold “as is”. A purchase receipt or other proof of the original purchase date is required for
warranty service.
Carry-In, Mail-in or In-Home Service
For Carry-In, Mail-In or In-Home Service (as applicable) in the United States call toll free contact number listed above or
For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.
In-Home service, if applicable, requires clear, complete and easy access to the product by the authorized servicer and
does not include removal or re-installation of an installed product. It is possible that certain in-home repairs will not be
completed in-home, but will require that the product, or parts of the product, be removed for shop diagnosis and/or repair
and then returned.
76
Others
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear
and tear or cosmetic damage, nor does it cover markings or retained images on the picture tube resulting from viewing
fixed images (including, among other things, letterbox pictures on standard 4:3 screen TV’s, or non-expanded standard 4:3
pictures on wide screen TV’s, or onscreen data in a stationary and fixed location). The warranty ALSO DOES NOT
COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or
failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation,
set-up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage,
modification, or commercial use (such as in a hotel, office, restaurant, or other business), rental use of the product,
service by anyone other than a Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of
God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE
WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE
OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages
for lost time, cost of having someone remove or re-install an installed unit if applicable, or travel to and from the servicer,
loss of media or images, data or other memory or recorded content. The items listed are not exclusive, but are for
illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED
TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an
implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a
problem with this product develops during or after the warranty period, you may contact your dealer or Servicenter. If the
problem is not handled to your satisfaction, then write to the warrantor’s Consumer Affairs Department at the addresses
listed for the warrantor.
PARTS AND SERVICE (INCLUDING COST OF AN IN-HOME SERVICE CALL, WHERE APPLICABLE) WHICH ARE
NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR RESPONSIBILITY.
77
Others
Customer Services Directory
Obtain Product Information and Operating Assistance; locate your nearest Dealer
or Servicenter; purchase Parts and Accessories; or make Customer Service and
Literature requests by visiting our Web Site at:
or, contact us via the web at:
You may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.
For hearing or speech impaired TTY users, TTY : 1-877-833-8855
Accessory Purchases
Purchase Parts, Accessories and Instruction Books online for all Panasonic Products
by visiting our Web Site at:
or, send your request by E-mail to:
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday – Friday 9 am to 8 pm, EST.)
Panasonic Services Company
20421 84th Avenue South,
Kent, WA 98032
(We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY : 1-866-605-1277
Product Repairs
Centralized Factory Servicenter
Panasonic Services Company
1705 N. Randall Road,
MAIL TO :
Elgin, IL 60123-7847
Attention: Camcorder Repair
Please carefully pack and ship, prepaid and insured, to the Elgin Centralized Factory Servicenter.
Customer’s in Puerto Rico, please ship or carry in to location below (“Service in Puerto Rico”).
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company
Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Phone (787)750-4300, Fax (787)768-2910
As of October 2003
78
Others
Spanish Quick Use Guide/Guía Para Uso Rápido
Precauciones para su seguridad
ADVERTENCIA:
Para evitar incendios y descargas eléctricas, no exponga este equipo a
la lluvia ni a la humedad.
Su
Camcorder está diseñada para grabar y reproducir en el modo de Reproducción Estándar (SP) y
modo Largo (LP).
Se recomienda el uso sólo de cintas de cassette que hayan sido probadas e inspeccionadas para su uso
en aparatos VCR con la marca
.
Este símbolo tiene por finalidad alertar al usuario
acerca de la presencia de tensión sin aislación en
el interior del producto, que puede tener la
intensidad suficiente como para causar descargas
eléctricas. Por lo tanto, hacer contacto con
cualquier pieza en el interior de la unidad es
peligroso.
Este símbolo tiene por finalidad alertar al usuario
de la presencia de importantes instrucciones de
operación y mantenimiento en la literatura incluida
con la unidad. Por lo tanto, lea detenidamente la
literatura incluida para evitar problemas.
La etiqueta de régimen está pegada en la base de la cubierta del cargador.
Este dispositivo cumple con la parte 15 de las Reglas del FCC. El funcionamiento está sujeto a las dos
siguientes condiciones: (1) Este dispositivo puede no causar interferencias perjudiciales, y (2) este
dispositivo debe aceptar cualquier interferencia recibida, incluyendo interferencias que pueden causar un
funcionamiento no deseado.
Nota:
Este equipo ha sido puesto a prueba y se encontró que cumple con la Parte 15 de las reglas del FCC.
Estos limites están diseñados para proveer una protección razonable contra interferencias cuando se
opera en un ambiente residencial.
Si este equipo causa interferencias en la recepción de radio o televisión, lo cual se puede comprobar al
apagar y encender el equipo, utilice el equipo en otra ubicación y/o utilice un tomacorriente diferente al
que está utilizando el receptor.
Si es necesario, consulte con el distribuidor o un técnico experto de radio/TV para solicitar ayuda. Puede
encontrar útil el folleto ‘Información sobre las interferencias’ disponible en las oficinas regionales del FCC
local.
Advertencia del FCC:
Para asegurar la conformidad continua del FCC, utilice solamente el cable de interfaz blindado cuando
conecte una cámara de video digital a una computadora de acuerdo con las instrucciones incluidas aquí.
También, cualquier cambio sin autorización o modificaciones a este equipo anularían la autoridad del
usuario para operarlo.
79
Others
Inserción de una tarjeta de memoria
(Sólo para el modelo
PV-GS12/PV-GS14/PV-GS15)
1 Usando su pulgar presione la perilla [OPEN▼]
Guía rápida
1 Coloque la batería en el adaptador de CA y
cárguela.
1 y saque la pantalla LCD 2 en la dirección
de la flecha.
2
1
• Antes de usar, cargue completamente la batería.
• Debido a que la batería no se cargará cuando
el cable de entrada de CC esté conectado al
adaptador de CA, desconéctelo del adaptador de
CA.
• La lámpara [CHARGE] se enciende, y comienza
la carga.
• Cuando la lámpara [CHARGE] se apaga, se ha
terminado la carga.
2 Deslice la palanca [OPEN] 3 para abrir la
cubierta de la ranura de tarjeta 4 .
3 Mientras sostiene la tarjeta de memoria con
su esquina cortada hacia la derecha 5
insértela en la ranura de tarjeta 6 .
4 Cierre bien la cubierta de ranura de tarjeta 4 .
3
2 Coloque la batería cargada en el Camcorder.
4
6
5
Grabación de una cinta
1 Ajuste el interruptor [OFF/ON] 1 a [ON].
• La lámpara [POWER] 2 se enciende.
Inserción de un cassette
1 Deslice la palanca [OPEN/EJECT] 1 hacia el
frente y tire hacia abajo para abrir la tapa del
compartimiento del cassette.
• Para proteger la cinta, el casete no podrá
expulsarse, si la tapa no está completamente
abierta.
1
2
2 Gire el dial de modo a modo de grabación de
cinta.
2 Inserte un cassette.
1
(PV-GS9)
(PV-GS12/
PV-GS14/
PV-GS15)
3 Cierre el soporte del cassette presionando la
marca [PUSH] 2 .
3 Presione el botón de inicio/parada de
grabación.
• Comienza la grabación.
4 Cierre la cubierta del compartimiento del
cassette presionando la marca 3 .
2
3
4 Presione el botón de inicio/parada de
grabación nuevamente para detener la
grabación.
80
Others
2 Gire el dial de modo a Modo de reproducción
de cinta.
Grabación de una imagen fija en cinta
(Sólo para el modelo PV-GS9)
1 Gire el dial de modo a modo de grabación de
cinta.
(PV-GS9)
(PV-GS12/
PV-GS14/
PV-GS15)
3 Presione el botón [
cinta.
] para rebobinar la
2 Presione el botón [PHOTO SHOT] en el modo
de pausa de grabación.
4 Presione el botón [►] para comenzar la
reproducción.
Grabación de una imagen fija en tarjeta
(Photoshot)
(Sólo para el modelo
PV-GS12/PV-GS14/PV-GS15)
5 Para parar la reproducción.
• Presione el botón [ ].
1 Gire el dial de modo a modo de grabación de
tarjeta.
Reproducción de una tarjeta de memoria
(Sólo para el modelo
2 Presione el botón [PHOTO SHOT].
PV-GS12/PV-GS14/PV-GS15)
1 Gire el dial de modo a modo de reproducción
de foto.
Reproducción de una cinta
1 Ajuste el interruptor [OFF/ON] 1 a [ON].
• La lámpara [POWER] 2 se enciende.
2 Comience la reproducción.
►:
Comienzo de una presentación
Reproducción de la foto siguiente
Reproducción de la foto anterior
Parada de la presentación
:
1
2
:
:
:
Pausa en la presentación
81
Others
Index
A
H
AC Adaptor................................................ 15, 66
ArcSoft Software ............................................. 55
Audio Dubbing................................................. 44
Auto Focus ...................................................... 71
Headphones.................................................... 64
I
Iris.................................................................... 32
B
L
Backlight.......................................................... 29
Black & White Mode........................................ 33
Blank Search................................................... 24
Built-in LED Video Light................................... 26
LCD Monitor .............................................. 19, 68
Limited Warranty ............................................. 76
Lock Setting..................................................... 41
Low Light Mode............................................... 30
C
M
Camcorder Accessory Order Form.................. 74
Camcorder Accessory System ........................ 73
Charging the Battery ....................................... 15
Cinema Mode.................................................. 29
Condensation .................................................. 66
Cue Playback .................................................. 35
Customer Services Directory........................... 78
Macro Close-up............................................... 27
MagicPix Function........................................... 29
Manual Focus.................................................. 32
Memory Stop................................................... 71
Mirror Mode ..................................................... 33
Mix Mode......................................................... 34
Mosaic Mode................................................... 33
Multi-Picture Mode .......................................... 33
D
Date/Time Indication........................................ 60
Date/Time Setting............................................ 23
Digital Effects................................................... 33
Digital Still Picture ........................................... 25
Digital Zoom .................................................... 27
DPOF Setting .................................................. 41
Dubbing........................................................... 45
DV STUDIO 3.1E-SE (Optional Software) ...... 53
N
Negative Mode ................................................ 33
P
Photoshot ........................................................ 25
Picture-in-Picture Mode................................... 34
Picture Size ..................................................... 39
Playback Digital Effects................................... 38
Playback with Zoom Lever .............................. 36
Playback Zoom................................................ 37
Portrait Mode................................................... 30
Program AE..................................................... 30
E
Erasure Prevention Slider ............................... 17
F
Fade ................................................................ 28
Formatting a Card ........................................... 42
F Number......................................................... 32
Q
Quick Start....................................................... 26
82
Others
R
U
RapidFire Consecutive Photoshot................... 26
Recording Check............................................. 24
Recording Speed............................................. 23
Remaining Battery Power................................ 59
Remaining Tape Time...................................... 59
Remote Control ............................................... 14
Repeat Playback ............................................. 64
Request for Service Notice.............................. 75
Review Playback............................................. 35
USB Connection Kit......................................... 47
V
Variable Speed Search.................................... 36
Video Head Clogging....................................... 67
Viewfinder.................................................. 19, 68
W
Web Camera ................................................... 50
White Balance ................................................. 30
Wipe Mode ...................................................... 34
S
SD Memory Card............................................. 57
Self-timer Recording........................................ 27
Self Recording................................................. 26
Sensor tag....................................................... 16
Sepia Mode ..................................................... 33
Shutter Speed ................................................. 32
Simultaneous Motion/Still Record Mode ......... 24
Slide Show ...................................................... 39
Slim Mode ....................................................... 33
Slow Motion Playback ..................................... 36
Solarisation Mode............................................ 33
Sound Volume................................................. 35
SP/LP Mode .................................................... 23
Spanish Quick Use Guide ............................... 79
Sports Mode.................................................... 30
Spotlight Mode ................................................ 30
Still Advance Playback .................................... 36
Stretch Mode................................................... 33
Strobe Mode.................................................... 33
Surf & Snow Mode .......................................... 30
Z
Zoom ............................................................... 27
Zoom Microphone ........................................... 27
T
Time Code....................................................... 71
Trailing Effect Mode......................................... 33
83
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094
P
Panasonic Sales Company (“PSC”),
Printed in Indonesia
LSQT0802 A
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infanteria, Km. 9.5 San Gabriel Industrial Park Carolina,
Puerto Rico 00985
S0104A1024
|