LOCATION AND FUNCTION OF CONTROLS
SPECIFICATION
GENERAL
Supply Voltage
Current Consumption
MAX Power Output
Number of channels
Unit Dimensions
DC 14.4 V. Negative Ground
Max.15A
40Watts X 4
2 STEREO channels.
178[W] X 164[D] X 50[H] mm.
FM SECTION
Frequency range
Effective sensitivity
I.F Frequency
87.5MHz -107.9MHz
3uV.
10.7MHz.
AM SECTION
Frequency range
Effective sensitivity
I.F Frequency
530KHz - 1710KHz
40dB.
450KHz
RCA LINE OUT (OPTION)
Output
1200mV @ CD MAX.
CD PLAYER
System
Suitable CDs
Frequency characteristics
MP3 Audio System.
MP3, WMA, CD, CD-R, CD-RW Disc
20Hz-100Hz < 5dB
10KHz-20KHz < 5dB.
50dB [1KHz]
S/N Ratio to CD
1. SEL( AUDIO MODE SELECT)/ROTARY VOL KNOB
(1) Press SEL button shortly and repeatedly to change the mode in the sequence as follows:
--> VOL --> BAS --> TRE --> BAL --> FAD -->
1) VOLUME CONTROL
A. The volume level can be adjusted at any time by rotating the VOL knob as select mode
has been initially defaulted at volume mode.
B. The volume level is also obtained by stepping through the SEL button until the function
VOL is displayed and then rotate the VOL knob to adjust the sound level.
2) BASS CONTROL
A. Press the SEL button to select the bass mode until BAS appears on the display.
B. Rotate the VOL knob to adjust the bass effect.
3) TREBLE CONTROL
A. Press the SEL button to select the treble mode until TRE appears on the display.
B. Rotate the VOL knob to adjust the treble effect.
4) BALANCE CONTROL
A. Press the SEL button to select the balance mode until BALappears on the display.
B. Rotate the VOL knob to increase or decrease the sound level of left or right speaker.
5) FADER CONTROL
A. Press the SEL button to select the fader mode until FAD appears on the display.
B. Rotate the VOL knob to increase or decrease the sound level of front or rear speaker.
Page 13
Page 2
TROUBLE SHOOTING
(2) When pressed longer 2 seconds, it is activated as cyclical mode of following functions for
user s selection.
-> BEEP (2nd/ALL/OFF) ->SEEK1/ 2 -> DSP(OFF/POP/ROCK/CLASSIC/FLAT) ->
SUBW ON/OFF-> VOL LAST/VOLADJ -> ESP 40/10 seconds mode.
After selecting the desired mode, rotate the VOL knob to select one setup item of the
desired mode.
Before using the check list please make all the connections first.
If you still have questions after going through the checklist, please consult
your local customer service representative.
BEEP 2ND, BEEP ALL, BEEP OFF MODE:
The unit is equipped with 3 mode beep sound, After entering this mode by pressing
the SEL button, rotate the VOL knob to choose one.
Common Symptoms
Cause
Solution
- Beep 2nd mode: The beep is only generated when an allotted double key is pressed long
(1 second).
If the power supply is properly connected to
the car accessory, switch the ignition key to
" ON " or " ACC " .
The car ignition is switched off.
There is no power.
- Beep all mode: The beep is generated when every key is pressed.
- Beep off mode: The beep sound is disabled when a key is pressed.
SEEK 1/SEEK 2 mode:( Only available during radio operation)
SEEK 1: Press and hold the >>| or |<< button to seek up or down for a station with a strong
signal. The seek stops when a station is reached .
Replace another fuse according to the wiring
diagram.
The fuse has blown.
The CDs can not
be loaded.
A disc is inside the player.
Remove the disc in the player then put a new
upward
SEEK 2: Press and hold the >>| or |<< button to seek up or down for a station with a strong
signal. The seek does not stop until the >>| or |<< button is released.
DSP(OFF/POP/ROCK/CLASSIC/FLAT):
The unit is equipped with 4 preset equalization modes. After entering this mode by pressing
the SEL button, rotate the VOL knob to choose one of 4 preset EQ s in the above order.
When using preset EQ modes you will not have access to Bass and Treble settings.
SUBW ON / OFF:
After entering this mode by pressing the SEL button, rotate the VOLknob to choose the
SUB-WOOFER ON or SUB-WOOFER OFF mode.
VOL LAST/VOL ADJ:
After entering this mode by pressing the SEL button, rotate the VOL knob to choose VOL
LAST or VOL addition.
The CDs are loaded The transport screws have not been Remove the transport screws before using.
only halfway into
the CD tray.
removed.
The disc is inserted upside-down.
Insert the compact disc with the label facing
upward
The device does
not work correctly
(EJECT, LOAD,
PLAY)
The surface of CD is extremely dirty Clean the CD or try another CD, if this works
or it is damaged.
correctly, the first CD is properly damaged.
Temperature inside the car is too
high.
Cool off until the ambient temperature returns
to normal
The volume control is set too low.
Turn up the volume properly.
VOL LAST: The radio switches on at the actual volume it had when it was last switched off.
VOL ADJ: Rotating the VOLknob you can pre-select a constant switch-on volume after
entering into this mode.
There is no sound.
Check the power and earth connection
according to the wiring diagram.
The device has not been correctly
connected.
ESP 40 /10 seconds:
1.The built-in microcomputer is not
operating properly due to noise
1. Switch the device off and on again. Or press
the RESET button to resume the program.
Briefly press the SEL button to access the ESP function (anti-shock system which improves
playback if there are shocks or vibrations); you can choose between two lengths of time for
ESP, either 40 seconds (ESP 40) or 10 seconds (ESP 10) by rotating the VOL knob.
The operation keys
do not work
2.The front panel is not properly
installed.
2. Reinstall the front panel
2. COVER CAP of USB SOCKET
The installation angle is more than
30 degrees
Adjust the installation angle to less than 30
degrees
When needing to insert USB bar into the USB socket, uncover the plastic cover cap and then
store it for safety. When not using the USB device, please cover it with the plastic cover cap.
The surface of the road is uneven.
Wait until the road becomes smoother before
playing the CD.
The sound of the
CD player skips
The surface of CD is extremely dirty Clean the CD or try another CD, if this works
or it is damaged. correctly, the first CD is properly damaged.
3. LCD (LIQUID CRYSTALDISPLAY)
No radio reception. The antenna cable is not connected. Insert the antenna cable firmly into the
antenna socket of the device.
4&5. TUNE, SEEK, TRACK, SKIP UP / DOWN BUTTONS
In automatic search The transmission signals are too
mode the radio does weak.
not stop at a trans-
Tune in to a radio station manually.
1)In RADIO mode, press >>| or |<< button shortly and repeatedly to manually tune up or down
for the desired radio station with step by step. Press >>| or |<< button hold for more than 0.5
seconds to auto-matically tune up or down for the radio station of strong signal.
mitting station.
2) In MMC/SD, USB or DISC mode, press >>| button to play next track. Press |<< button once
to play the current track from the beginning of the current track, press |<< button twice
continuously to play the last track. Press >>| or |<< button hold to skip forward or backward.
Page 3
Page 12
6. AUTO-STORAGE/PRESET MEMORYSCAN BUTTON
1) In radio mode, press it to perform all stations memory for 5 seconds each time, while memory
digital and frequency will flash on LCD. If the button is pressed for more than 2 seconds, it will
seek station on current band, then write to the preset memories. When the auto-storage
operation is completed, it will automatically perform for 5 seconds each time. After finishing 1
loop of memory scan, it will listen to the first memory station in the current band.
PRECAUTION OF DISC PLAY:
Cleaning the CD:
Before playing a CD, wipe it off with a clean, dust-free cleaning cloth.
Wipe the disc in the direction of the arrow.
2) In MMC/SD or USB mode, press A.P button repeatedly to select TRACK SEARCH or
DIRECTORY SEARCH mode.
In MP3/WMA disc mode, press A.Pbutton repeatedly to select TRACK SEARCH, FIRST
CHARACTER SEARCH or DIRECTORY SEARCH mode.
3) In TRACK SEARCH mode of MMC/SD, USB or MP3/WMA disc, the LCD will display MP3/
WMA T 000 and flash the biggest digit 0 that the MMC/SD card, USB bar or MP3/WMAdisc
contain.
Then rotate the VOL knob to select the number of the flashing digit from 0 ~ 9. Then press
SEL button to confirm the number and flash next smaller digit 0. With the same means, select
the number of the flashing digit. After finishing selecting the number of all flashing digit, press
SEL button to play the track of the selected serial number.
In FIRST CHARACTER SEARCH mode of MP3/WMA disc, the LCD will display A--......, If there
are files names its first character are A , the ......is the first file name its first character isA by the
order of A~Z and 0~9; otherwise, the ......is NONE. Rotate the VOL knob to select file s first
character by the order of A~Z and 0~9. Then press >>| or |<< button to select one file its first
characters is the selected one. Finally press SEL button to play the selected file.
In DIRECTORY SEARCH mode of MMC/SD, USB or MP3/WMA disc, the LCD will display the
root folder(if there is not the root folder, it will found a root folder named ROOT).
Then rotate the VOL knob to select your desired folder and then press >>| or |<< button to select
your desired track in the folder. Finally press SEL button to play the selected track.
Always insert the CD with the label side facing upwards.
If the CD is inserted with the printed side facing downwards, the device may be
damaged.
Note: If there is already a CD in the CD slot, do not try to insert a second CD.
This may damage the device.
7. BAND BUTTON
Always hold CDs by the edge. In order to keep the CD clean do not touch the surface.
Pull out the CD as shown below.
Press the BND button briefly to select the radio broadcasting band you would like to hear.
The AM/FM band is toggled cyclically through the tuning bands
->FM 1-> FM 2 -> FM 3 -> AM 1->AM 2 ->.
In MP3/WMA disc mode, if you press BND button repeatedly, the file name, folder name,
song s title, artist and album information will be scrolling on the LCD display.
As long as the current playing MP3/WMA music contains relevant ID3 tag information in version
1.0/2.0 format, the 3 items underlined above will be scrolling on the LCD display; otherwise, they
will not.
In CD,MP3 or WMA mixed-formatted disc playback mode, pressing the BND button for more
than 2 seconds will change among the playing the CD,MP3 and WMA formatted songs.
In a default mode, the unit will first play all the CD formatted songs and then play the MP3/WMA
formatted songs.
Do not attach any sticker or adhesive tape on the CD.
Do not expose the CD to direct sunlight or sources of heat such as heating vents.
Do not leave CDs in a car if it is parked in direct sunlight as that will lead to a con-
siderable rise in the temperature inside the car.
8. LOUDNESS BUTTON
When press shortly, the LOUD mode is turned on, its to enhance the bass sound effect when
the volume level is low. Press again to cancel the loudness effect.
Note: Do not use any solvents such as petrol or thinning agents.
Commercially available cleaning substances or antistatic spray. This will damage
the device.
9. LOCAL/DISTANCE BUTTON
Radio station search mode is divided by this LOC/DX switch, this button can be used to control
an attenuator in the tuner during search. The detecting level of seek, scan, auto-memory will be
reduced as much as the attenuated level of the tuner. In radio mode, press the LOC button to
change local reception or distance reception. (Note: This button is only for FM reception. )
Page 11
Page 4
10. POWER BUTTON
PRECAUTIONS AND MAINTENANCE
Press any button except the EJECT and RELEASE button to turn on the unit.
It also can turn on the unit to insert disc, MMC/SD card or USB bar into their compartment or
socket. Press PWR button hold for more than 0.5 seconds to turn off the unit.
1. If the car interior is extremely hot, as after being parked in the sun, do
not use the player until the car has been driven for a while to cool off
the interior.
2. The protective case is to safely keep the front panel.
PROTECTIVE CASE
11. STEREO/MONO BUTTON
Press the button to select STEREO or MONO sound mode.
12. MUTE BUTTON
This button serves to switch the MUTED state on/off.
Press the MUTE button to suppress the loudspeaker temporarily, and press
again to resume listening. The muted state will be also released when the
MODE, BAND, SEL button is pressed and VOL knob on the front panel is used.
FRONT PANEL
3. The unit is designed for negative terminal of the battery which is connected
to the vehicle metal. Please confirm it before installation.
13. PRESET STATION [ 1-6 ] AND TOP/CDP, INT, RPT, RDM BUTTONS.
4. Do not allow the speaker wires to be shorted together when the unit is
switched on. Otherwise it may overload or burn out the power amplifier.
5. Do not install the detachable panel before connecting the wire.
A).RADIO MODE
When pressed short, these keys select a preset station directly,
When pressed longer than one seconds, current station is stored in preset memory bank.
B).In MMC/SD, USB or disc mode, press TOP/CDP button to pause MMC/SD, USB or
disc playback, press it again to resume MMC/SD, USB or disc playback. Press it hold
for more than about 0.5 seconds to play the first track of the MMC/SD, USB or disc.
C).In MMC/SD, USB mode, press INT button shortly to display M-INT and play the first 10
seconds part of each track of all.
WIRING DIAGRAM
In CD/MP3/WMA disc mode, press INT button shortly to display S-INT and play the first 10
seconds part of each track of all.
In MMC/SD, USB or MP3/WMA disc mode, Press INT button long to display D-INT and play the
first 10 seconds part of each in current folder.
During INT mode, press INT button again to stop INT mode and retain playing the track
currently selected.
ANTENNA PLUG
YELLOW
FUSED
FILTER
BOX
1A & 15A
FUSES
MEMORY B+
BLACK (GND)
POWER B+
RED R
RCA LINE OUT
D).In MMC/SD, USB mode, press RPT button shortly to display M-RPT and play the current
track repeatedly.
REAR (GRAY)
WOOFER LINE OUT
WHITE L
RED
YELLOW
RED R
In CD/MP3/WMA disc mode, press RPT button shortly to display S-RPT and play the current
track repeatedly.
RCA LINE OUT
FRONT (BLACK)
0.5A
FUSE
BLUE AUTO ANT
WHITE L
In MMC/SD, USB or MP3/WMA disc mode, Press RPT button long to display D-RPT and play the
current folder repeatedly.
During RPT mode, Press RPT button again to cancel RPT mode.
FRONT
4 Ohm
+
+
+
FRONT
4 Ohm
GRAY
WHITE
WHITE / BLACK
GREEN
GRAY / BLACK
VIOLET
RIGHT
SP
LEFT
SP
E). In MMC/SD, USB mode, press RDM button shortly to display M-RDM and play the track
of all in random order.
+
REAR
4 Ohm
REAR
4 Ohm
In CD/MP3/WMA disc mode, press RDM button shortly to display S-RDM and play the track
of all in random order.
VIOLET / BLACK
GREEN / BLACK
In MMC/SD, USB or MP3/WMA disc mode, Press RDM button long to display D-RDM play the
track in the current folder in random order.
During RDM mode, Press RDM button again to cancel RDM mode.
Note:
1.Make sure usea speaker with4 ohm loadimpedance.
2.Do not makethe auto antennawire and groundtouch each other.
Page 5
Page 10
F).In MMC/SD, USB or MP3/WMA disc mode, M6 and M5 is assigned as 10 TRACK up/down
when normal play.
14. MODE BUTTON
Press it to select RADIO, DISC, CARD(after inserting MMC/SD card), USB(after inserting
USB bar) and auxiliary input playing mode.
15. AUXILIARY INPUT JACK
You can connect any external audio device to the auxiliary input jack.Then press the mode
button to select auxiliary input playing mode, use the volume control to adjust volume.
16&17. MMC/SD COMPARTMENT and USB SOCKET and THEIR OPERATION
When needing to do MMC/SD or USB playing, insert the MMC/SD card or USB bar into
MMC/SD compartment or USB socket. Then the playing mode will be changed into MMC/SD
or USB mode and display CARD or USB on LCD(When MMC/SD card and USB bar are both
inserted into their compartment or socket, the playing mode will be changed into the mode of
the latter one), and then play the first track of MMC/SD or USB.
18. RELEASE BUTTON
To remove the front panel from the unit chassis, press the RELkey to release the front
panel from the unit chassis, then pull it up a little to take out from the unit chassis.
19. INFRARED REMOTE CONTROL SENSOR
20. EJECT BUTTON
Press this key, a loaded disc can be to ejected.
21. CLOCK BUTTON
Press the CLK button briefly to display time for 5 seconds on the display, and then returns to
its previous display unless the button is pressed again.
Then press the CLK button and hold for more than 1 seconds until the real time flashes on the
display. Then you can adjust HOUR or MINUTE by rotating the VOL knob.
22. SCAN BUTTON
Press it to scan up by one channel step with station detection. If a valid signal has detected,
the current frequency is blinked within 5 seconds, then press it again to stop scan and remain
the current frequency; otherwise, the unit continue to scan up by one channel step with station
detection 5 seconds later.
Page 9
Page 6
23. RESET BUTTON
MAINTENANCE OF REMOTE CONTROLLER
Before operating the unit for the first time, or after replacing the car battery or changing the
connections. You must reset the unit.
After removing the faceplate, press this button with a cuspidal object.
This operation will erase the clock setting and some stored contents.
An insulation tag was installed in your remote by the manufacturer to prevent the
battery from draining. Removing the tag from the remote before using.
OPERATION OF REMOTE CONTROL:
BATTERY INFORMATION:
Lithium Battery: CR2025 3V
Battery Life: Approximately 6 months.
NOTE:
Before using the remote control, be sure to
turn on the unit by pressing the POWER button
on the front panel.
Replacing the Battery from the Remote Controller:
1) Remove the battery holder by pressing the locking tab with your thumb
and pulling it out.
2) Replace the battery with the same type and the
3) Gently push in the holder until securely locked into place.
+
side facing up.
1. Power On/Off.
2. Mute Button
3. Loudness Button
4. Level/MENU UP Button
5. SEL/MENU Button
6. Level/MENU Down Button
7. MO/ST Button
WARNING:
8. A.P Button
Do not recharge, disassemble or dispose of in fire.
Battery leakage may cause damage to the unit.
To avoid the risk of accident, keep batteries out of reach of children.
9. Band Button
10. Mode Button
16. CD Track TOP/ /Radio Preset 1
11. Tune/Seek Up And
Track Skip Up/FF Button
17. CD Track INT/Radio Preset 2
12. Tune/Seek Down And
Track Skip Down/REW Button
18. CD Track RPT/Radio Preset 3
13. SCN Button
19. CD Track RDM/Radio Preset 4
14. Clock Display /Setting Button
20. Radio Preset 5/10 Tracks Down
15. LOC Button
21. Radio Preset 6/10 Tracks Up
Page 7
Page 8
|