Morphy Richards Blender mill User Manual

Blender & mill  
Please read and keep these instructions  
getting the best from your new  
blender and mill  
Safety first  
The blender and mill blades are very sharp, therefore handle with care when  
using and cleaning.  
Quantities  
Do not overfill the blender. Refer to the operating chart for quantities and  
operating times.  
Ensure the blender lid is in place  
When using the blender ensure the lid is in place before switching on and do  
not remove until the blades have stopped rotating.  
Do not overfill the blender. This could  
cause damage to the motor. The 3A  
fuse will blow if the blender is over  
loaded. Replace fuse and do not  
exceed the maximum recommended  
volumes. Refer to the operating chart.  
Do not blend or mill for longer than the  
time periods recommended in the  
operating chart.  
When using the blender or mill ensure  
the lid is in place before switching on  
and do not remove the lid until the  
blade has stopped rotating.  
Features of your blender  
and mill attachment  
Filler cap  
Lid  
Jug  
Base unit  
Cord storage  
Control switch  
Mill attachment jar  
Mill attachment  
Electrical requirements  
Check that the voltage on the rating plate of  
your appliance corresponds with your house  
electricity supply which must be A.C.(Alternating  
current).  
If the socket outlets in your home are not  
suitable for the plug supplied with this appliance  
the plug should be removed and the appropriate  
one fitted.  
IMP0RTANT : THE PLUG REMOVED FROM  
THE MAINS LEAD, IF SEVERED, MUST BE  
DESTROYED AS A PLUG WITH A BARED  
FLEXIBLE CORD IS HAZARDOUS IF EN-  
GAGED INTO A LIVE SOCKET OUTLET.  
Should the fuse in the 13 amp plug require  
replacement, a 3 amp BS1362 fuse must be  
fitted.  
This appliance is a double insulated  
product and it does not require an earth.  
Blender & mill use  
Use your blender for soups, sauces, drinks,  
pates, mayonnaise, dressings etc.  
Use your mill for milling herbs, nuts and coffee  
beans.  
3
IMPORTANT:  
Operating controls  
Blender and Mill  
The blender control switch has the following  
settings. Pulse, off, speed 1 and speed 2.  
To ensure the long life of your blender never run it  
for longer than 60 seconds or the mill for longer  
than 30 seconds. Switch off as soon as you have  
reached the desired consistency.  
PULSE  
CLEAN  
OFF  
SPEED 1  
SPEED 2  
Don’t process spices they may damage the  
plastic.  
The machine will not work if the blender or mill  
is fitted incorrectly.  
The speed can be adjusted whilst the blender  
is in use.  
Blender only  
Using the pulse button allows greater control  
over the texture of the food produced. It is only  
intended to be used for short ‘bursts’ of blending.  
Don’t put dry ingredients into the blender  
before switching on. If necessary, cut them  
into pieces; remove the filler cap; then, with  
the machine running drop the pieces through  
one by one.  
Operating the blender  
Setting up  
Empty regularly  
1
2
Ensure the blender base unit  
from the mains.  
Place the blender jug  
is unplugged  
Don’t use the blender as a storage container.  
Keep it empty when not in use.  
onto the base unit  
Never blend more than 1 litre (1 3/4 pints) -  
less for frothy liquids such as milk shakes.  
and turn anti-clockwise until the tabs on  
the jug lock securely into the slots on the  
base unit.  
Mill only  
Use for dry ingredients only  
Operating the mill  
1
Put your ingredients into the mill attachment  
jar and fill it no more than half full.  
3
4
Place the food in the blender.  
Place the lid  
filler cap  
onto the blender. Then put the  
into the lock position.  
Always ensure the blender lid has clicked into  
place.  
5
6
Plug in the blender and turn the control switch  
to either pulse, speed 1 or speed 2  
depending on the desired consistency.Always  
operate the blender with the lid in place.  
Never operate the blender with more than  
1500ml of liquid or when empty.  
4
4
5
Turn the correct way up.  
2
3
Turn the mill attachment  
upside down and  
Place the mill onto the base unit and twist anti-  
clockwise until the tabs on the mill lock  
securely into the slots on the base unit.  
lower into the mill attachment jar  
down).  
Place the mill attachment into the jar and twist  
in a clockwise direction to lock.  
(blades  
6
Switch the unit on using the control switch and  
select the desired control speed.  
Operating chart  
15 secs-1min  
Begin with low speed and  
increase to high if  
required.  
Blending/  
liquidising  
Soups, purees,  
drinks,  
milkshakes,  
batters  
1.5 lt  
1-2  
+ pulse  
pulse  
10 secs -  
30 secs  
Milling  
Herbs  
nuts  
coffee beans  
DO NOT OVER PROCESS FOR LONGER THAN RECOMMENDED TIME  
DO NOT EXCEED RECOMMEDED MAXIMUM VOLUMES  
5
Hints and tips  
Cleaning and storage  
When making mayonnaise, put all the  
ingredients, except the oil, into the blender. Then  
with the machine running, pour the oil slowly into  
the blender through the filler cap hole.  
BEFORE CLEANING, SWITCH OFF AND  
UNPLUG THE MAINS LEAD.  
After use, fill the blender or mill attachment  
with warm water and run for 30 seconds on the  
pulse setting and repeat as necessary. Never use  
abrasives or cream cleaners. Clean the base unit  
with a damp cloth or kitchen paper roll.  
NEVER IMMERSE THE BLENDER BASE  
UNIT IN WATER.  
Thick mixtures, eg. pates and dips, may need  
scrapping down with a spatula (ensure the  
appliance is switched off first). If the mixture is  
difficult to process add more liquid.  
After the blender has been cleaned, the mains  
When crushing ice, add 15ml (1tbsp) water  
to 6 ice cubes and operate the blender in short  
bursts using pulse setting.  
lead can be wound round the storage area  
underneath the base unit.  
When blending pour the liquids in first and  
then add the solid food. Begin blending at the  
lower speed and increase when needed.  
6
Helpline  
If you have any difficulty with your appliance,  
do not hesitate to call us. We’re more likely able  
to help than the store from where you bought it.  
Please have the following information ready to  
enable our staff to deal with your query quickly.  
Name of the product  
Model number as shown on the  
underside of the appliance.  
Serial number as shown on underside  
of the appliance.  
7
To qualify for the 2 year guarantee the appliance  
must have been used according to the manu-  
facturers instructions. For example kettles  
should have been regularly descaled.  
Your two year  
guarantee  
EXCLUSIONS  
It is important to retain the retailers  
Morphy Richards shall not be liable to replace  
or repair the goods under the terms of the  
Guarantee where:  
1 The fault has been caused or is attributable  
to accidental use, misuse, negligent use or  
used contrary to the manufacturers  
recommendations or where the fault has  
been caused by power surges or damage  
caused in transit.  
2 The appliance has been used on a voltage  
supply other than that stamped on the  
products.  
3 Repairs have been attempted by persons  
other than our service staff (or authorised  
dealer).  
4 Where the appliance has been used for hire  
purposes or non-domestic use.  
5 Morphy Richards are not liable to carry out  
any type of servicing work, under the  
guarantee.  
6 Plastic filters for all Morphy Richards kettles  
and coffee makers are not covered by the  
guarantee.  
This guarantee does not confer any rights  
other than those expressly set out above and  
does not cover any claims for consequential  
loss or damage. This guarantee is offered as an  
additional benefit and does not affect your  
statutory rights as a consumer.  
receipt as proof of purchase. Staple your  
receipt to this back cover for future reference.  
Please quote the following information if the  
product develops a fault. These numbers can  
be found on the base of the product.  
Model No.  
Serial No.  
All Morphy Richards products are individually  
tested before leaving the factory. In the unlikely  
event of any appliance proving to be faulty within  
28 days of purchase it should be returned to the  
place of purchase for it to be replaced.  
If the fault develops after 28 days and within  
24 months of original purchase, you should  
contact the Helpline number quoting Model  
number and Serial number on the product, or  
write to Morphy Richards at the address shown.  
You will be asked to return the product (in  
secure, adequate packaging) to the address  
below along with a copy of proof of purchase.  
Subject to the exclusions set out below (see  
‘Exclusions’) the faulty appliance will then be  
repaired or replaced and dispatched usually  
within 7 working days of receipt.  
If for any reason this item is replaced during  
the 2 year guarantee period, the guarantee on  
the new item will be calculated from original  
purchase date. Therefore it is vital to retain your  
original till receipt or invoice to indicate the date  
of initial purchase.  
This guarantee is valid in the UK and Ireland  
only.  
Morphy Richards products are  
intended for household use only.  
The After Sales Division,  
Morphy Richards Ltd, Mexborough,  
South Yorkshire, England, S64 8AJ  
Morphy Richards has a policy of  
continuous improvement in product  
quality and design.  
The Company, therefore, reserves  
the right to change the  
Helpline (office hours)  
specification of its models at any time.  
UK 0870 060 2612  
Republic of Ireland 1800 409119  
444/8502/84 Rev 2  

RCA Small Wonder EZ217 User Manual
Raymarine Radar equipment Chartplotter RL70CRC PLUS User Manual
Phoenix Gold Car Amplifier TI2 16005 User Manual
Philips AJ 3800 User Manual
Orion Telescopes Binoculars Camcorder 52099 User Manual
Lochinvar SOLUTION CB 180 User Manual
Listen Technologies LA 325 User Manual
Kenwood eXcelon KDC X994 User Manual
Kalorik USK BL 16910 User Manual
JVC LYT0844 001A User Manual