FUNCTION OF CONTROLS
R
6
16 9
14
19
1
18
7
5
17
L
U
D
C D / C D - R / C D - R W P L A Y E R
L
U
D
DISP
RPT
RDM
SCAN
ALL
DIR
SONG
CLASSIC
JAZZ
JC-CD160
BND
ST
MUT
LOC
CLK
LUD
3
MUTE
LOUD
AF
PTY EON
MUSIC
MONO
60 WATT/DIGITAL TUNING SYSTEM
SCN
A/PS
2INT
4RDM
1
3RPT
5
6
MODE
Instruction Manual
L
U
D
21
22
23
20
2
15
11
12
13
4
8
10
L
U
D
C D / C D - R / C D - R W P L A Y E R
CONTROL
FUNCTIONS
L
U
D
DISP
RPT
RDM
SCAN
ALL
DIR
SONG
CLASSIC
JAZZ
BND
ST
MUT
LOC
CLK
LUD
MUTE
LOUD
AF
PTY EON
MUSIC
MONO
1POWER ON/OFF
Press the button to power up the unit
Press and hold for more than 1 second to turn off unit.
2,3. SEL (control mode select)/MENU KEY
60 WATT/DIGITAL TUNING SYSTEM
SCN
A/PS
2INT
4RDM
5
1
3RPT
6
MODE
L
U
D
Push to select the desired mode,VOL(volume),BAS(bass),TRE(treble)
BAL(balance),or FAD(fader).
This button normally functions as the volume control.Adjust the level
rotate(3) clockwise after selecting the desired control mode.
Otherwise the mode will go back to the volume control mode.
CAR CD PLAYER ASP 12/45SEC
RECEIVER(AM/FM)
Turn counter clockwise:
Control Mode
Volume control
Bass control
Turn clockwise:
For less volume
For less bass
For more volume
For more bass
Treble control
Balance control
Fader control
For less treble
To decrease the rightspeaker volume
To decrease the frontspeaker volume
For more treble
To increase the leftspeaker volume
Toincrease the rearspeaker volume
DETACHABLE FRONT PANEL
MENU KEY
Hold the SEL key to choose the menu.
1) menu1: AUDIO DSP FUNCTION
Press and hold longer than one second to activate the DSP feature.Rotate the SEL knob to select
DSP mode sound effect as shown in sequence below .User setting value of bass/treble in normal
mode is always memorized.In rock/classic/pops mode,bass/treble mode is skipped and level is
not changeable
FLAT----CLASSICS----POP M----ROCK M----DSP OFF.
Bass and Treble gain of each mode is as shown in below table.
Initial value of bass/treble in NORMAL mode is 0 dB.
-- 1 --
REMOVING THE FRONT PANEL
Front Panel
CD CONTROL LOCATION OF PARTS
18
19
17
L
U
D
C D / C D - R / C D - R W P L A Y E R
L
U
D
Release Button
DISP
RPT
RDM
SCAN
ALL
DIR
SONG
CLASSIC
JAZZ
BND
ST
MUT
LOC
CLK
LUD
MUTE
LOUD
MONO AF
PTY EON
INSTALLING THE FRONT PANEL
MUSIC
60 WATT/DIGITAL TUNING SYSTEM
SCN
A/PS
2INT
4RDM
6
1
3RPT
5
MODE
L
U
D
21
22
20
23
17.CD EJECT BUTTON
Press the EJECT button to remove the CD.The receiver will automatically switch to radio mode.
18.CD SLOT
PRECAUTIONS
Do not touch the contacts on the front panel or on the unit body, since this may result
in poor electrical conductivety.If dirt or other foreign substances get on the contacts, wiper
them with a clean dry cloth.
19.TRACK/SEARCH BUTTON
FORWARD AND REVERSE TRACK SEARCH
PRECAUTIONS WHEN HANDLING THE FRONT PANEL
Press the SKIP button or
during play to go to the desired track(song).
Do not leave the front panel in any area exposed to high temperatures or direct sunlight.
Do not drop the front panel or otherwise subject it to strong impact.
Do not allow such volatile agents as benzene, thinner, or insecticides to come into contactwith the
surface of the front panel.
(
....REVERSE)(
....FORWARD)
Press and hold the SKIP button or during play to scan the disc at high speed.When the
desired music section of the disc is found,release the button.Normal play will resume.
20.PAUSE BUTTON
Never try to disassemble the front panel.
During PLAY ,press button to PAUSE.Press it again to resume play.
21.INT BUTTON (Priview all Tracks)
INSTALLATION
This feature allowes you to listen to the first 10 seconds of each track on the
display .Press the key SCAN indicator appears on the LCD pannel.
To cancel the function press the key again.
NOTE:
Choose the mounting location where the unit will not interfere with normal driving function.
Before finally installing the unit, connect the wiring temporarily and make sure it is all connected
up properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use of unauthorized
parts can cause malfunctions.
22.REPEAT BUTTON (RPT)
To repeat the current track press the key.The RPT indicator appears on the LCD
panel and the track be repeated continuously.
To cancel the function press the key again.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications
of the vehicle.
Install the unit where it does not get in the driver s way and cannot injure the passenger if there
is a sudden stop. Like an emergency stop.
23.RANDOM BUTTON (RDM)
Press the key. Tracks will be player in randomorder.
To cancel the function the press the key again.
If installation angle exceeds 30 from horizontal the unit might not give optimum performance.
Avoid installating the unit where it would be subject to high temperature.such as from direct
sunlight. Lower case or from hot air,from the heater,or where it would be subect to dust,.dirt or
excessive vibration.
HOW TO REMOVE AND INSTALL THE FRONT PANEL
1. Press the release button and pull-off the front panel.
2. To install the front panel, insert the panel into the housing and make sure the panel is securely
installed, otherwise, abnormalities occurs on the display or some keys will not function properly.
DIN FRONT/REAR-MOUNT
This unit be can properly installed either from Front (conventional DIN Front-mount) or Rear
(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For
detail, refer to the following illustrated installation methods.
-- 5 --
-- 4 --
DIN FRONT- MOUNT (Method A)
Installing the unit
USING THE RESET BUTTON
Press button with a thin, pointed object if unit is malfonctioning. Though not a normal
occurrence, the microprocessor which controls the operation of this unit can be affected
by electrostatic noise.
This generally is indicated by such symptoms as no power being supplied when you switch
the unit on, failure of buttons and controls, or an abnormal display.
Should this happen, press the reset button with a thin, pointed object to reset the
microprocessor.
2
1
1. Dashboard
2. Holder
After inserting the holder into the
dashboard, select the appropriate tab
according to the thickness of the
dashboard material and bend them
inwards to secure the holder in place.
3. Screw
3
1. Dashboard
2. Nut (5mm)
3. Spring washer
1
4. Screw (5 x 16mm)
5. Screw
6. Strap
6
7
4
Be sure to use the strap to secure the
back of the unit of the place. The strap
can be bent by hand to the desired
angle.
RESET
FLASHING
5
2
7. Plain washer
3
SPECIFICATIONS
MW(AM) SECTION
1. Frame
2. Insert fingers into the groove in the front
of frame and pull out to remove the
frame .(When re-attaching the frame.
Point the side with a groove downwards
and attach it.)
1
Frequency Range
Channel Step
Intermediate Frequency
Usable Sensitivity
Image Rejection Ratio
If Rejection Ratio
: 530 - 1710 KHz
: 10 KHz
: 450 KHz
: 33 dB
: >50 dB
3. Lever
Insert the levers supplied with the unit
into the grooves at both sides of the unit
as shown in figure until they click.
Pulling the levers makes it possible to
remove the unit from the dashboard.
3
: >50 dB
FM SECTION
4 SPEAKER WIRING
Frequency Range
Channel Step
: 87.5-107.9 MHz
: 200 Khz
Intermediate Frequency
Image Rejection Ratio at 106KHz
Signal to noise ratio
: 10.7 MHz
: >50 dB
: >60 dB
CONNECTIONS
ANTENNA
CD PLAYER SECTION
BLACK
GROUND(-)
RED(R)
Signal to noise Radio
Channel separation
: More than 60dB
: More than 60dB
FUSE
LINE OUT
WHITE(L)
BLUE
AUTO ANT(+)
GRAY
0.5A
Frequency Response
: 20Hz - 20KHz
RED
B (+)
RED(R)
1A
LINE IN
WHITE(L)
BLACK
YELLOW
BACK UP
7A
GENERAL
GRAY +
FRONT
+ WHITE
FRONT
LEFT
RIGHT
Power Supply Voltage
Speaker impedance
Maximum Output Power
Dimensions Chassis
: DC 12 Volts Negative Ground
: 4 -8
: 15W x 4CH
SPEAKER
SPEAKER
- WHITE/BLACK
+ GREEN/BLACK
GRAY/BLACK-
VIOLET +
REAR
REAR
LEFT
SPEAKER
RIGHT
: 178(W) x 50 (H) x 160(D)mm
SPEAKER
- GREEN
VIOLET/BLACK-
-- 7 --
-- 6 --
|