MONO CHANNEL CLASS "D"
AUTOMOTIVE AMPLIFIER
G1-1200 / G1-2000 / G1-3000
INSTRUCTION MANUAL
CONGRATULATIONS ON YOUR PURCHASE
Your new high fidelity mono block amplifier is designed to deliver maximum enjoyment
and one year of trouble free service. Please take a few moments to read this manual
thoroughly. It will explainthe features andoperation of yourunit and helpinsure trouble
free installation.
FEATURES
• Class ''D'' Technology
• 1 Ohm Stable
• Spec AudiophileGrade Components
• High Efficiency PWM Power Supply
- Multi-stranded powertoroid
- Tow toroidal core
- MOSFET transistors
• Oversized Capacitor Banks
• Discrete Mount Powerand speaker terminals
• Variable Low Pass ElectronicCrossover 50Hz - 250Hz
• Built in powerbridging module
• Circuit / Thermal / OverloadProtection
• Bridge Sync Capable
• Remote Level Control
IMPORTANT
PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION !
The quality of installation may affect the performance and reliability of your product. If
you have any doubts or questions regarding installation, you may wish to contact your
authorized dealer. Remember to heed all wire and fuse requirements suggested in this
manual. Warranty may be void if proper installation technique is not used (refer to warranty
section in the rear of the manual )
1
INSTALLATION
MOUNTING:
1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1.
2. Once thelocation has beendetermined, place theamplifier into position. Using a felttip
pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as
a template for drilling. It is very easy to damage the amplifier surface in this manner.
3. Remove amplifier. Drill four 3.5 m/m holes into mounting surface. If you want to mount
the amplifier to MDF or wood panel, drill four 3.0m/m diameter holes into mounting surface.
4. If possible, test the system to ensure it is operating correctly before final mounting of
the amplifier.
Mount the amplifier using the supplied 4 self tapping screws.
5.
INSTALLATION DIAGRAM
Self Tapping Screws
FIG.1
2
SPEAKER WIRING
The Class "D" amplifier is a SINGLE CHANNEL dedicated subwoofer amplifier. Unlike
other amplifiers, the Class "D" operates as a single channel and cannot be bridged.
Don't be fooled by the outputs. Two outputs are used strictly for convenience and are
paralleled internally on the amplifier. This means that if both outputs are used with one
driver each, the amplifier sees the same load as if the same drivers are connected to
only one outputterminal. See diagrambelow.
digital mono block AMPLIFIER
G1-2000
POWER
REM
SPEAKER
B+
GND
FUSE
30A
30A
30A
4OHM
SUBWOOFER
4OHM
SUBWOOFER
digital mono block AMPLIFIER
G1-2000
POWER
REM
SPEAKER
B+
GND
FUSE
30A
30A
30A
4OHM
SUBWOOFER
4OHM
SUBWOOFER
In both diagrams, the amplifiersees a 2 ohm load.
3
SPEAKER WIRING
MONO BRIDGED
MASTER SLAVE
Master
Amplifier
MASTER SLAVE
LINE INPUT
GAIN
LPF
BASS BOOST
MASTER
/SLAVE
CH1
CH2
6V 0.2V 50Hz 250Hz 0dB 12dB
REMOTE
GAIN CONTROL
FROM
RADIO
MASTER SLAVE
Slave
Amplifier
MASTER SLAVE
LINE INPUT
GAIN
LPF
BASS BOOST
MASTER
/SLAVE
CH1
CH2
6V 0.2V 50Hz 250Hz 0dB 12dB
REMOTE
GAIN CONTROL
WIRING SUBWOOFERS (DUAL AMPS)
When using dual amplifiers to power one subwoofer, the Positive terminal of the Subwoofers
voice coil is connected the positive terminal of the MASTER Amplifier and the Negative terminal
of the Subwoofers voice coil is connected to Positive terminal on the SLAVE Amplifier. This
procedure will allow the total power of both amplifiers to be added together and act like a single
powerful amplifier. Please check that your subwoofer power handling capabilities are not exceeded
when hooking two amplifiers to it.
CAUTION
Always check your speaker load with a multi-meter before hooking up to the amplifier. These
digital amplifiers are only 1 ohm stable. Any Impedance (load) smaller than 1 ohm will damage
the amplifier. SuchDamage is not covered underwarranty either, sopay strict attention to what
connections are madeto the amplifier.
4
SPEAKER WIRING
MONO BRIDGED
Master
Amplifier
digital mono block AMPLIFIER
G1-2000
POWER
REM
SPEAKER
B+
GND
FUSE
30A
30A
30A
Using a lead wire of 8 gauge or
bigger connect from the master
Amp's negative(-) speaker
terminal to the slave Amp's
negative(-) speaker terminal.
digital mono block AMPLIFIER
G1-2000
POWER
REM
SPEAKER
B+
GND
Slave
FUSE
Amplifier
30A
30A
30A
BATTERY VIA FUSE
CHASSIS GROUND
REMOTE TURN ON
(OPTION) TWO AMPLIFIER/ ONESUBWOOFER (SINGLE VOICE COIL)CONFIGURATION
digital mono block AMPLIFIER
Gd-1000
POWER
REM
Master
Amplifier
SPEAKER
B+
GND
FUSE
30A
30A
30A
digital mono block AMPLIFIER
Gd-1000
POWER
REM
SPEAKER
B+
GND
FUSE
Slave
Amplifier
30A
30A
30A
Recommend : Competition Only
5
SPEAKER WIRING
MONO BRIDGED
(OPTION) FOUR AMPLIFIER/ ONESUBWOOFER (DUAL VOICE COIL)CONFIGURATION
digital mono block AMPLIFIER
G1-2000
POWER
REM
SPEAKER
Master
B+
GND
FUSE
Amplifier
30A
30A
30A
Voice
Coil1
Voice
Coil2
Slave
Amplifier
digital mono block AMPLIFIER
G1-2000
POWER
REM
SPEAKER
B+
GND
FUSE
30A
30A
30A
Master
Amplifier
digital mono block AMPLIFIER
G1-2000
POWER
REM
SPEAKER
B+
GND
FUSE
30A
30A
30A
digital mono block AMPLIFIER
G1-2000
POWER
REM
SPEAKER
B+
GND
FUSE
Slave
Amplifier
30A
30A
30A
6
POWER SUPPLY CONNECTIONS
The Class "D" amplifier is designed to work within 10 to 16 volts DC. Before any wires
are connected, the vehicle's electrical system should be checked for correct voltage
supply with the help of a voltmeter. First check the voltage at the battery terminals with
the ignition in the off position. The voltmeter should read no less than 12 volts. Next,
check the battery with the engine running between 1500 and 2000 rpm. The voltmeter
should now read between 13.5 and 14.5 volts. If your vehicle's electrical system Is not
up to these specifications, we recommend having it checked by an automotive mechanic
before further installation.
RECOMMENDED POWER WIRE
The proper wire size is very imporat nt for an amplifier of this power level. Because the
Class "D" amplifier is capable of drawing in excess of 90 amperes,4 gauge wire is
recommended for lengths up to twenty feet. if a longer length is neede,da larger gauge
wire may be necessary.
POWER
Amplifier power wire should be wired directly to the battery using the wire requirements
listed above. Start at the amplifier and run the power wire through the vehicle to the
battery. The use of grommets is recommended when passing the power wire through
any metal wall. Avoid sharp corners or sharp body parts that may easily cut through the
insulation on the wire. Avoid running the power wire over engine components and near
heater cores. Use an inline fuse to eliminate the risk of a fire caused by a short in yoru
power wire. Connect the fuse holder as close to the battery positive as possible. For
most applications, an 80 ampere Maxi fuse or comparable ANL wafer fuse can be used.
Now connect the wire to the battery, but remember to leave the fuse out untli all other
wire connections are mode.
GROUND
When grounding your amplifier, locate a metal area close to the amplifier that is a good
source of ground ( preferably the floor ).Once again, investigate the area you wish to use
for electrical wires, vacuum lines, and brake or fuel lines. Using either a wire brush or
sandpaper eliminate unwanted paint to supply a better contact for your ground. Use the
same gauge wire for ground as you did for the power. Terminate the ground wire using the
correct size ring terminal and attach it to the bare metal using a nut and bolt. It is important
for this connection to be solid. To complete the job, spread silicon over the screw and bare
metal to prevent rust and possible water leaks.
REMOTE TURN-ON
In between the power and ground is a remote turn-on terminal. This terminal must be
connected to a switched +12volt source. Typically, remote turn-on leads are provided
at the source unit that will turn on and off the amplifier in correspondence with the source.
If a radio does not have a remote turn-on, then a power antenna wire may be used. Yet, if
neither of these leads are available at the source, a switched +12 volt supply must be
supplied. Run a minimum of 18-gauge wire from the amplifier location to the source of the
switched +12 volt lead. If possible, route this wire on the same side of the vehicle as your
power wire. Connect the source remote output wire to the REM terminal on the amplifier
using a 3mm screw key. Cut the remote wire to length. Strip approximately 1/2 inch of
insulation from theend of thewire and insertinto the terminal. Tighten thescrew securely.
7
OPERATION
1
2
3
4
5
6
7
MASTER SLAVE
LINE INPUT
GAIN
LPF
BASS BOOST
MASTER
/SLAVE
CH1
6V 0.2V 50Hz 250Hz 0dB 12dB
REMOTE
GAIN CONTROL
CH2
1. RCA Input Jacks
4. Bass Boost
5. Remote Control Jack 6. Master/Slave Switch
2. Input Level Control
3. Low Pass Frequency
7. Slave Input Jack
Control and Crossover
1. RCA Input Jacks - Low level-high impedance inputs. Use high quality RCAcables designed
for mobile applications.
2. Input Level Control - Adjust the input level for the marked channels. Turn clockwise to
increase the level, counterclockwiseto decrease. Amplifiers will run cooler and produce
less system noise at lower level settings.
3. Low Pass Frequency - Adjust the crossover frequency by turning clockwise to set to a higher
frequency, counterclockwiseto set to a lower frequency.
4. Bass Boost - Adjust the sub boost level of the selected frequency outputfrom 0dB to 12dB.
5. Remote Control Jack - For connecting the remote control module to the amplifier.
6. Master/Slave Switch -Select the remote level control or the on-board level control as the
master control.
7. Slave Input Jack - Used to connect to another amplifier when bridging 2 amps together.
The Slave mode bypasses normal input jacks and controls.
8
FRONT/REAR PANEL
MASTER SLAVE
LINE INPUT
GAIN
LPF
BASS BOOST
MASTER
/SLAVE
CH1
CH2
6V 0.2V 50Hz 250Hz 0dB 12dB
REMOTE
GAIN CONTROL
G1-1200/2000/3000 front
digital mono block AMPLIFIER
Gd-1500
POWER
REM
SPEAKER
B+
GND
FUSE
25A
25A
25A
G1-1200 REAR
digital mono block AMPLIFIER
Gd-2000
POWER
REM
SPEAKER
B+
GND
FUSE
30A
30A
30A
G1-2000 REAR
digital mono block AMPLIFIER
Gd-3000
POWER
REM
SPEAKER
B+
GND
G1-3000 REAR
9
TROUBLE SHOOTING GUIDE
This section providesyou with acatalog of amplifiersymptoms and theirprobable causes
and solutions. Beforeyou consult thislisting, make surethe vehicle's electricalsystem is
working properly byverifying that otherelectrical items (e. g. headlights, windows, etc.)
Still function correctly.
SYMPTOM
PROBABLE CAUSE
SOLUTION
No Audio
Low or N.C Remote
Turn-on connections
Check remote turn-on voltage at
amp and head unit
Blown Fuse
Power wires not connected
Replace with new fast-blow fuse
Check butt splices or solder joints
Check ground and battery
connections
Blown or non speakers
connected
Use VOM or DVM to measure speaker
coil
impedance; check speaker wiring
connections
Distorted Audio
Input Sensitivity not set
properly
See adjustment procedure and check
each step;
or damaged speaker cones
Inspect each speaker for damage
and repair or replace suspected
component
Low turn-on voltage
Refer to head unit owner's manual
Audio Level Low
Audio Lacks
Mute circuit on head
unit is on.
Check electrical system for low
voltage;
Check ground connection
Speakers wired with wrong
polarity, causing
cancellation of bass
frequencies
Check polarity of wires from
amplifiers to each speaker as defined
by the system design
Check battery voltage at amplifier
during operation
External Fuse
Blowing
Incorrect wiring or short
circuit
Refer to electrical installation and
check each installation step
Whining noise
on audio with
engine running
Amplifier is picking
up alternator noise
Install an in-line noise filter on the
head unit's power wire; Check
alternator routing diodes or voltage
regulator for proper operation. Check
all grounds , battery voltage, and
RCA cables
Ticking noise on
audio with
engine
Amplifier is picking up
radiated spark noise
Check RCA audio cable; Install an
in-line noise filter on the head unit's
power wire. Check spark plug wires.
running
10
SPECIFICATION
AMPLIFIER
G1-1200
G1-2000
G1-3000
RMS POWER / 1 ohm @ 1% T.H.D
2 ohms @ 0.05% T.H.D
1200W x 1
750W x 1
400W x 1
90%
2000W x 1
1000W x 1
500W x 1
90%
3000W x 1
2000W x 1
1000W x 1
90%
4 ohms @ 0.05% T.H.D
Efficiency / Typical @ 4 ohms
MIN RATE @ 1 ohm
79%
79%
79%
Bandwidth ±1dB
10Hz ~ 250Hz
>100dB
10Hz ~ 250Hz
>100dB
10Hz ~ 250Hz
>100dB
Signal To Noise Ratio ('A' WTD)
Damping Factor
Input Sensitivity
150
150
150
200mV ~ 6V
200mV ~ 6V
200mV ~ 6V
Input Impedance
X-Over Slope
20K Ohms
24dB
20K Ohms
24dB
20K Ohms
24dB
Variable Low Pass Filter
Variable Bass Boost
50 ~ 250Hz
0dB ~ 12dB
50 ~ 250Hz
0dB ~ 12dB
50 ~ 250Hz
0dB ~ 12dB
Need External Fuse/
Minimum 180 Amp
75Amp
90 Amp
Circuit Breaker
Dimensions (W x H x D) mm
245 x 55 x 320
245 x 55 x 350
245 x 55 x 420
NOTE : Specifications & design subject to change without notice
for improvements.
11
WARRANTY
WARRANTY LIMITATIONS
The following is NOT covered under Interfire
Audio's warranty program:
WARRANTY TERMS
(Effective January 01, 2010)
These terms supersede all prior published
warranty terms
1. Product owned by anyone other than the
original purchaser from an authorized
Interfire Audio dealer. (The warranty is
NOT transferable and will not apply to
products purchased from unauthorized
dealers.)
Interfire Audio products are warrantied against
defects in materials and workmanship for a
period of One (1) Year from the original date of
purchase.
Products found to be defective during the
warranty period will be repaired or replaced
(with a product deemed to be equivalent) at
Interfire's discretion.
2. Speaker products thathave been over-
powered, causing thermal (burnt voice coil)
and/or mechanical failure (ripped surrounds
or spiders).
Note: Products purchased from unauthorized
dealers are not covered under warranty. Ask
your dealer for details on warranty limitations.
3. Product that has NOT been installed
according to the instructions in the owner's
manual
INTERNATIONAL WARRANTIES:
Products purchased outside the United States
of America are covered only by that country's
distributor and not by Interfire Audio, Inc.
4. Product in which repair and/or modification
has been attempted by unauthorized parties
IF YOU NEED SERVICE ON YOUR
INTERFIRE AUDIO PRODUCT:
5. Product damaged in an accident, due to
criminal activity (attempted theft, gunshot
damage, etc.) or by "acts of God" (flooding,
lightning, etc.)
Please call Interfire Customer Service at
1-877-90-AUDIO to obtain an RA #(Return
Authorization number). All warranty returns
should be sent to INTERFIRE AUDIO freight
prepaid through an authorized INTERFIRE
AUDIO dealer and must be accompanied
by proof of purchase (a copy of theoriginal
sales receipt.) Direct returns from consumers
or non-authorized dealers will be refused
unless specifically authorized by INTERFIRE
AUDIO with avalid return authorization
number. Warranty expiration on products
returned without proof ofpurchase will be
determined from the manufacturing date
code. Coverage may be invalidated as this
date is previous topurchase date. Return
only defective components. Non-defective
items received will be returned freight-collect.
Customer is responsible for shipping charges
and insurance in sending the product to
INTERFIRE AUDIO. Freight damage on
returns is not covered under warranty.
Always include proof of purchase (sales
receipt).
6. Product that has been physically damaged
abused and/or altered. Including bent frames
or missing magnets.
7. Custom finishes or other cosmetic treatments
applied to products. (Interfire Audio will not be
responsible for restoring or maintaining any
Custom finishes)
8. Product with defaced, altered or removed
serial numbers (no valid, legible serial No.
= no warranty).
9. Product damaged cosmetically due to
improper handling or normal wear and
tear Including Freight damage. Besure
to package all returns in its packing material
and box.
10. Installation and shipping costs associated
with removing, re-installing or shipping the
product to Interfire Audio for warranty service
NOTICE: Products shipped without a valid RA# will be refused and shipped back.
|