·
·
TSE270X TSE271X TSE272X
INSTRUCTION MANUAL
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The CAUTION label, shown on the left, is attached
on the top of camera.
INFORMATION
This equipment has been tested and found to comply
with the limits for Class A digital device, pursuant
to Part 15 of the FCC Rules.These limits are
desinged to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment.This equipment generates,
uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the
instruction manual, may cause harmful interference
to radio communications. Operation of this equipment
in a residential area is likely to cause harmful
interference in which case the user will be required
to correct the interference at his own expense.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
CAUTION
Do not use any power supply other than specified.
WARNING
USER-INSTALLER CAUTION:Your authority to operate
this FCC verified equipment could be voided if
you make changes or modifications not expressly
approved by the party responsible for compliance
to Part of the FCC Rules.
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
PRECAUTIONS FOR USE AND INSTALLATION
* Install your camera where no video noise appears.
When camera cables have been laid near electric wires or
television receivers, a noise may interfere the image.
If noise occurs, relocate cables or reinstall equipment.
* Check the ambient temperature and humidity.
Avoid using camera in areas where temperature is
consistently hotter or colder than the specified range (See
Specifications chart below) or poor image quality or
damaged parts may occur.
* Never aim the camera at the sun.
Never aim or point the camera at the sun even if you are
not shooting.
* Do not shoot intense light.
Strong light such as a spot light on the image plane will
cause blooming or smear. When strong light comes into
the image plane, vertical stripes may appear on it.
However, this does not mean that the camera is defect.
* Take precautions when handling a camera.
Do not drop your camera, or give it a strong shook or
vibration. This may cause camera to malfunction.
* Do not touch internal parts.
Precautions should also be taken to avoid areas of high
humidity.
* Should you notice any trouble.
Be sure not to touch the internal parts. This may cause to
electrical shock.
If any trouble occurs while you are using the camera, turn
off the camera and contact your dealer. Failure to do so may
cause damage to the camera.
* Do not let the camera get wet.
Install the camera at the place where it will not get wet.
Should it gets wet, turn off the power immediately and
contact your dealer.
* The socket-outlet should be installed near the equipment
and should be easily accessible.
SPECIFICATION
Model
TSE270X
AC24V 10% 60Hz 1Hz
Approx.6W
TSE271X
DC12V (DC11V-16V)
Approx.3.2W
TSE272X
AC120V 10% 60Hz 1Hz
Approx.6W
Power source
Power consumption
Pick-up device
Effective picture element
Scanning area
1/3" Black & White interline-transfer CCD
512 (H) X 492 (V)
4.92mm (H) X 3.69mm (V)
2:1 interlaced
Scanning system
Scanning frequency(H)(V)
Sync. system
15.75Hz 60Hz
Line-lock
15.75Hz 60Hz
Line-lock
15.734Hz 59.94Hz
Internal
Resolution
380TV lines (Horizontal) 350TV lines (Vertical)
More than 46dB
S/N ratio
Recommended illumination
AGC
22 lx (F1.2 under incandescent lamp)
Built into camera circuitry
Sens-up
Provided (Factory-set at OFF)
Provided (Factory-set at OFF)
Provided (Factory-set at OFF)
Backlight control
AES
(Automatic Electronic Shutter)
Gamma correction
Accumulation node
Output signal
0.45
Field
VBS 1.0 Vp-p, 75Ω, EIA, compatible
Auto-iris terminal
Power terminal
Lens mount
4P (DC/Video)
Power cord
3P terminal
2P terminal
CS
Ambient temperature
Ambient humidity
Dimensions
-10°C ~ +50°C (14°F~122°F)
30% ~ 90%
60(W) X 60(H) X 120(D)mm (2.4 X 2.4 X 4.9 inches)
510 grm (1.13 lbs) 320 grm (0.71 lbs)
600 grm (1.32 lbs)
Weight
Note: Weight and dimensions are approximate.
Design and specifications are subject to change without prior notice.
- 2 -
PART NAMES AND FUNCTIONS
2
4
1
3
10
2
1 Lens mount
Mount a CS-mount lens.
2 Camera mount
For mounting a camera on wall, housing, etc.
(1/4"-20UNC thread)
MODEL TSE270X
MODEL TSE271X
MODEL TSE272X
3 Focusing dial
For fine-adjustment of the lens back-focus.
4 IRIS terminal
Connect when an automatic iris lens is used.
5
6
7
5
VIDEO OUT terminal
Connect to a monitor TV, etc. (BNC connector)
AC power terminal
6
7
Connect this to optional AC 24V power supply.
Ground terminal
Connect this to the ground wire of the power supply cord.
5
8
8 DC power terminal
Connect this to optional DC 12V power supply.
9 Power cord
Connect this to AC120V power supply.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE
5
DE LA PRISE ET POUSSER JUSQU' AU FOND.
Camera control switches
10
9
Refer to "CAMERA CONTROLS." on page 6.
- 3 -
HOW TO CONNECT
1. Before connection, make sure that power of all units are OFF and cords are unplugged.
2. Mount a lens onto the camera. Refer to "HOW TO USE" for usable lens.
3. Connect video terminal of the camera and the video input terminal of a monitor TV, etc. with a 75Ω coaxial cable.
4. Connect the power terminal of the camera to a power supply.
Caution: Installation should be made by a qualified service personnel and should conform to all local codes.
Lens, coaxial cable for video signal and power supply are not supplied with a camera.
HOW TO USE
1. TSE270X: Turn on the unit by connecting the power cord of AC 24V power supply.
TSE271X: Turn on the unit by connecting the power cord of DC 12V power supply.
TSE272X: Connect the power cord to AC 120V and turn the power ON.
2. Adjust the iris and focus of the lens so that optimum image may
be obtained.
CS-mount
*Usable lenses
Lens
5mm or less
CS-mount lenses, whose length "L" (in the illustration) from the
bearing surface of the mount is 5mm or less if protruded, should
be used.
L
*Using the zoom lens (adjustment of the back focus)
The camera is set at the standard back focus position when
shipped from factory. Depending on types of zoom lenses,
Lens
Camera
however, slight readjustment may be necessary.
Adjust the lens back-focus by turning the focusing dial in either
Focusing dial
direction as per the illustration, referring to the following
instructions.
1
Place an object at any fixed distance and set the focus ring of the zoom lens accordingly.
2 Set the zoom lens to full TELE position and obtain the best focus position by turning the focus ring or the zoom
lens.
3 Set the zoom lens to full WIDE position and obtain the best focus position by turning the focusing dial located on
the side of the camera.
4 Repeat procedures
2
and 3 until focus remains constant throughout the zooming range.
Note: When weight of the lens is more than 1kg, the camera should be supported by the lens rather than relying
on camera mounting screw.
Adjust the back-focus only when necessary.
*Using an auto iris lens
When a DC driven type auto iris lens is used, set the AUTO IRIS switch at DC, and connect the plug of the lens
(for iris terminal) to the IRIS terminal on the right side of the camera.
When a video feedback type auto iris lens is used, set the AUTO IRIS switch at VIDEO, and connect the plug of
the lens (for iris terminal) to the IRIS terminal on the right side of the camera.
(Refer to Lens manual for the level adjustment.)
IRIS terminal
DC position
Control -
Control +
VIDEO position
+9V iris power (50mA Max.)
GND
1
2
3
4
Camera
Plug for IRIS terminal
(CHUOMUSEN E4-191J-100)
Auto iris lens
Drive +
Drive - (GND)
0.8Vp-p auto iris video signal
GND
Soldering side
*When a video feedback type auto iris lens (peak/average selectable type) is used at peak mode, BLC may not
function well. In such a case, select the average mode.
3. Before your use of the camera at AES (Automatic Electronic Shutter) mode.
*When using an auto-iris lens, set the AES switch at OFF.
(The AES switch is set at OFF when shipped from factory.)
*The AES mode may increase smears on monitors, which is caused by characteristics of CCD and is not defect.
Set the AES switch at OFF in case smears appear excessively.
- 4 -
LINE-LOCK CONTROL (TSE270X/TSE272X)
Matching the vertical synchronization with the power frequency is called the line-lock.
When two or more cameras are switched by the video switcher to a monitor TV, the vertical sync. phase can be locked
with the power frequency, and a stable vertical sync. is obtained without being disturbed at the time of switching.
Monitor TV
Video output
CAMERA
1
Video
input
Video switcher
Video output
To AC 24V power supply (TSE270X)
CAMERA
2
}
1.The camera is synchronized to the power frequency of 60Hz ±0.5Hz covering a normal fluctuation of the power
To AC 120V power supply (TSE272X)
Caution:
frequency.The camera may not compensate for large fluctuation caused by power generated by an engine
generator, etc.
2.It takes about 10 seconds or more to obtain a stable synchronization after the power is turned on. This is
necessary to stabilize the camera against the power noise.
- 5 -
CAMERA CONTROLS
By adjusting the switches/potentiometers provided on the side panel, the control functions are available.
1 AES switch
TSE270X, TSE272X
[Electronic shutter] The camera is
factory-set at the AES switch OFF
and 1/60 sec. shutter speed.
SENS-UP
AUTO IRIS
V-PHASE
[AES (Automatic Electronic Shutter)]
By setting the AES switch to ON, the
Automatic Electronic Shutter mode
(1/60~1/100,000 sec) is available.
AES
ON
BLC
ALC
LEVEL
DC VIDEO
Note: In electronic shutter mode;
*Sufficient brightness is
required.
OFF
*The picture will flicker
when shooting under the
illumination produced by
fluorescent lamp.
1
2
3
4
5
6
2 SENS-UP switch
To increase the sensitivity, set this
switch to ON position.
TSE271X
SENS-UP
AUTO IRIS
3 BLC (Back Light Control) switch
In case the back oighting is too
brighit to shoot the main object
clearly, set this swith to ON position.
AES
ON
BLC
ALC
LEVEL
DC VIDEO
OFF
4 ALC LEVEL
Adjust video output level, when
AUTO IRIS switch is DC position.
1
2
3
4
5
5 AUTO IRIS switch
When a DC driven type auto iris lens is used, set this switch to DC position.
When a video feedback type auto iris lens is used, set this switch to VIDEO position.
Vertical sync. phase adjustment potentiometer
6
Vertical sync. phase adjusting potentiometer is set at the position fully counterclockwise that the delay time of
vertical sync. phase against the phase of power frequency is shortest, when shipped from the factory.
Turning this potentiometer clockwise will make the delay time of vertical sync. Phase against the phase of
power frequency longer.
6
camera in combination with other camera(s) controlled by the Line-Lock synchronization.
Use the function control potentiometer
if the picture image on a monitor TV may flow when using the
In this case, get a proper image by shifting the phase of vertical sync. signal of the camera against that of the
other. If a proper image cannot be obtained even after this adjustment, reset the potentiometer to its original
6
position, and use the function control potentiometer
signal of other camera.
of the other camera to shift the phase of vertical sync.
Caution: Before making adjustment, make sure that cameras have their power supplies connected with the same
polarity. (not 180°apart)
- 6 -
PROFILE
All dimensions in mm (inch)
43 (1.69)
MODEL TSE270X
60 (2.36)
120 (4.72)
MODEL TSE271X
43 (1.69)
MODEL TSE272X
6-14, Meizen-cho, Mizuho-ku,
Nagoya, 467-8567 Japan
ELMO CO., LTD.
OVERSEAS SUBSIDIARY COMPANIES
ELMO Mfg. Corp.
ELMO Canada Mfg. Corp.
ELMO (Europe) G.m.b.H.
1478 Old Country Road,
Plainview, NY 11803-5034
U.S.A.
44 West Drive, Brampton,
Ontario, L6T 3T6,
Canada
Neanderstr. 18
40233 Dusseldorf,
Germany
Tel. 516-501-1400
Fax. 516-501-0429
E-mail:[email protected]
Tel. 905-453-7880
Fax. 905-453-2391
E-mail:[email protected]
Tel. 0211-376051-53
Fax. 0211-376630
E-mail:[email protected]
6X1NHVA02 B
Printed in CHINA
|