XHD6420
INSTALLATION/OWNER'SꢀMANUAL
AM/FM/CD/MP3/WMA/3.5mmꢀReceiver
withꢀBuilt-InꢀHDꢀRadio™ꢀandꢀDetachableꢀFace
R
XHD6420ꢀINSTALLATION
WiringꢀDiagram
Antenna Connector
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XHD64ꢀ0 uses one
10 amp ATM fuse located
beside the wiring connector.
ꢁ
XHD6420ꢀOPERATION
ControlꢀLocationsꢀ-ꢀReceiver
2
3
4
5
6
7
8
9
1
24
14 13
15
10
23 22 21 20 19
18 17 16
12 11
Release
Preset 6/Folder Up
1
2
13
14
15
16
17
18
19
20
21
22
23
24
Eject
Preset 5/Folder Down
Preset 4
Mode/Search
Volume/Audio/Setup
Tune/Track Up
IR Remote Sensor
Loudness
3
Preset ꢁ/Intro
4
Preset ꢀ/Random
Preset 1/Repeat
5
6
Auto Store/Preset Scan/Enter
Band/Play/Pause
HD Seek
7
EQ/Key 9
8
9
Display/Key 0
Auxiliary Input
Tuner Scan/Key 8
Key 7
10
11
12
Mute
Tune/Track Down
Power
The XHD64ꢀ0 allows playback of your favorite MPꢁ and WMA files recorded on CD-R and
CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while
maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic
Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track
search - even while a song is currently playing!
Function keys 7, 8, 9 and 0 apply to MPꢁ/WMA operation only.
4
XHD6420ꢀOPERATION
GeneralꢀOperation
FaceplateꢀRemoval Press RELEASE and pull away from the left side to remove.
To re-install, insert right side of faceplate first then push
left side to secure.
Semi-Permanentꢀ Remove trim ring and install supplied #1 x 7/ꢁꢀ” Phillips
FaceplateꢀInstallation head screw through left side of mounting frame into faceplate.
PowerꢀOn/Off Press POWER or any other button (except eject) to turn the
unit on. Inserting a disc will turn the unit on automatically.
Press POWER to turn the unit off.
ꢀ
Mode Press MODE to select between AM/FM, CD player and
auxiliary input. Modes of operation are indicated in the
display.
NOTE: CD mode will not appear unless a CD is inserted.
AuxiliaryꢀInput Insert ꢁ.5 mm plug to connect your portable audio device.
Volume Adjust volume using rotary encoder (00-46).
Programmableꢀ Press and hold POWER for ꢁ seconds to program currently
Turn-OnꢀVolume selected volume level. "P-VOL" and the current volume level
will momentarily appear in the display.
Mute Press MUTE to silence the audio. “MUTE” will flash in the
display. Press MUTE again to cancel.
PresetꢀEQꢀCurves Press EQꢀto select between POP, JAZZ, CLASSIC, BEAT,
ROCK and OFF (default) equalization curves. Any adjustment
to the Bass or Treble settings automatically cancels the
current EQ curve (if one is selected).
Reset Press to RESET the unit upon initial installation or if
abnormal operation occurs. The reset button is located
behind the faceplate.
Display Press DISP to select between clock and different types
of information, such as radio frequency, HD Radio song
information, CD track/elapsed time or MPꢁ/WMA song
information.
5
XHD6420ꢀOPERATION
GeneralꢀOperation
With the unit on, press and hold DISP until the clock begins to
flash, then release. Press TUNE to adjust the hours and
SetꢀtheꢀClock
nn
to adjust the minutes. Press DISP momentarily to
TUNEꢀ
ll
save the selected time.
Press and hold the rotaryꢀencoder for more than ꢁ seconds to
access the setup menu. Press the rotaryꢀencoder momentarily
to select between the menu functions and rotate the rotaryꢀ
encoder left/right to adjust or activate the desired function.
SetupꢀMenu
SetupꢀMenu
MenuꢀFunction
Options
Action
ClockꢀDisplay
CLK OFF
Programs the unit to not display the clock when the
power is off.
CLK ON
Programs the unit to display the clock when the
power is off.
AuxiliaryꢀInput
AUX ON
AUX OFF
Enables the front panel ꢁ.5mm auxiliary input.
Disables the auxiliary input.
BeepꢀConfirmation BEEP OFF
Disables the confirmation beep.
Enables the confirmation beep.
Activates distance tuning.
Activates local tuning for strong station reception
only.
BEEP ON
Local/Distanceꢀ
Tuning
LOC OFF
LOC ON
PowerꢀonꢀMessage MSG OFF
Disables power on message.
MSG ON
Enables power on message to be displayed.
Disables the demonstration mode.
Enables the "BUILT IN HD RADIO" message.
Demonstrationꢀ
Mode
DEMO OFF
DEMO ON
SCRL ON
DisplayꢀScrolling
Programs the unit to scroll display information
continuously.
SCRL OFF
Disables the display scroll feature.
6
XHD6420ꢀOPERATION
GeneralꢀOperation
Press rotaryꢀencoder momentarily to select between
Audio
Volume (default), Bass, Treble, Balance, & Fader.
VOLUME
BASS TREBLE
BALANCE
FADER
Press rotaryꢀencoder until BAS appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Bass
Treble
Press rotaryꢀencoder until TRE appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Press rotaryꢀencoder until BAL appears then rotate encoder
left/right to adjust (BAL L 1ꢀ-BAL 00-BAL R 1ꢀ).
BAL 00 represents equal balance
Balance
Press rotaryꢀencoder until FAD appears then rotate encoder
left/right to adjust (FAD F 1ꢀ-FAD 00-FAD R 1ꢀ).
FAD 00 represents equal fader
Fader
Individual Bass and Treble settings are retained in memory
for AM, FM, CD and AUX modes. This allows you to save the
Bass and Treble settings separately for each mode.
SourceꢀAudioꢀMemory
Note:
Any adjustment to the Bass or Treble settings automatically
cancels the current EQ curve (if one is selected).
7
XHD6420ꢀOPERATION
HDꢀRadio™ꢀAM/FMꢀTunerꢀOperation
AnalogꢀandꢀDigitalꢀTuning The following tuning functions will access both analog and
digital stations. Refer to the HDꢀSEEKꢀmodeꢀsection on page
10 for instructions on tuning to only digital stations.
SeekꢀTuning Press TUNE
or TUNEꢀllmomentarily to seek the
nn
next strong station.
When an HD Radio station is selected, an HD Radio logo will
begin to flash on the display. In about five seconds, HD or
HD1 will illuminate after the radio frequency.
• If "HD" appears, the radio station is broadcasting a higher
quality sound. No additional stations are available.
•
If "HD1" appears, additional multicast channels (HDꢀ
and/or HDꢁ) are available. Press TUNE or
TUNEꢀllto tune to other available multicast channels.
nn
ManualꢀTuning
Press TUNE
or TUNEꢀ
for more than two seconds,
nn
then release. "MANUAL" will momentarily appear in the
display. Press TUNE or TUNEꢀ momentarily to
ll
nn
ll
move radio frequency up or down one step at a time. Press
and hold to advance quickly. If tuning is not adjusted for five
seconds, the unit will return to seek tuning mode (default).
"AUTO" will momentarily appear in the display.
ScanꢀTuning
Press SCN to preview strong stations on the current band,
pausing for five seconds at each. Press SCN again to cancel.
StoringꢀandꢀRecallingꢀ
StationꢀPresets
Up to 18 FM stations and 1ꢀ AM stations can be stored,
including HD Radio stations. To store a station, first select
the desired band and station. Press and hold the desired
preset button (1-6) for more than two seconds. When stored,
the preset number appears in the display. The station can be
recalled by pressing the corresponding preset button.
Note: Function keys 7, 8, 9 and 0 apply to MPꢁ/WMA
operation only.
8
XHD6420ꢀOPERATIONꢀ
HDꢀRadio™ꢀAM/FMꢀTunerꢀOperation
AutomaticallyꢀStoreꢀ
Press AS/PS for more than two seconds to automatically
store the six strongest stations in the current band.
Automatic local tuning is activated during initial band scan.
Stations
PresetꢀScan
Press AS/PS momentarily to scan presets 1-6 on the
current band, pausing for five seconds at each. Press AS/PS
again to cancel.
Band
Press BAND to select FM1, FMꢀ, FMꢁ, AM1 or AMꢀ.
ꢀDisplay
When the unit is tuned to an analog station, press DISP to
toggle the display between the following options:
CLOCK
FREQUENCY
When the unit is tuned to an HD Radio station, press DISP to
toggle the display between the following options:
SONG
TITLE
STATION
NAME
PROGRAM
TYPE
ARTIST
CLOCK
FREQUENCY
When information is unavailable, "NO DATA" appears in the
display.
Press HDꢀSEEK to activate digital-only tuning mode. The HDꢀ
SEEK icon will appear on the display, indicating that the unit
will skip over analog stations and tune to HD Radio stations
only. Follow the instructions on page 9 to access seek,
manual and scan tuning.
HDꢀSeekꢀMode
•ꢀꢀStoringꢀandꢀRecallingꢀStationꢀPresets
HD Radio multicast stations (HDꢀ and HDꢁ) can also
be stored as presets. When a preset multicast station
is recalled, "LINKING" appears in the display until the
download process is complete (approximately 5 seconds).
ꢀ
Note: If the HD radio signal on the preset is unavailable,
the unit reverts to the previous analog or digital station.
• AutomaticallyꢀStoreꢀStations
While in HDꢀSEEK mode, press AS/PS to automatically
store HD Radio stations to presets 1-6. Multicast
channels (HDꢀ and/or) HDꢁ are not stored but can be
accessed by pressing TUNEꢀllfrom the HD1 station.
9
XHD6420ꢀOPERATIONꢀ
CDꢀPlayerꢀOperation
With the label facing up, insert a standard size CD into the
InsertꢀCD
CD slot. The CD will automatically begin playback.
Press EJECT to eject the CD. The unit will change to
previous mode of operation (tuner or AUX). If the disc is not
removed within 10 seconds, the unit will reload the disc. The
unit does not have to be turned on to eject CD.
EjectꢀCD
Press TRACKꢀ
track. Press TRACK
current track. Pressing TRACK
beginning of the previous track.
to skip to the beginning of the next
TrackꢀSelect
ll
to return to the beginning of the
nn
again skips to the
nn
Press and hold TRACKꢀ
or reverse a track.
or TRACK
to fast forward
FastꢀForwardꢀandꢀReverse
ll
nn
Press
Press
/
/
II to temporarily stop CD playback.
II again to resume playback.
Pause
Scan
l
l
Press INTꢀto play the first 10 seconds of each track.
Press INT again to cancel.
Press RPT to continuously repeat selected track.
Press RPT again to cancel.
Repeat
Random
Press RDM to play all tracks in random order. Press RDM
again to cancel. Random mode is retained in memory when
selecting between AM, FM, CD and AUX modes and when
the unit is turned on/off.
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method. In
addition, the following CDs may be incompatible with this
unit:
CD-R/CD-RWꢀCompatibility
CDs exposed to extreme temperatures or direct sunlight
for extended periods of time, CDs recorded in which a
recording session failed or a re-recording was attempted
and, or encrypted or copy-protected CDs which do not
conform to the audio CD-DA red book recording standard.
10
XHD6420ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
When an MPꢁ/WMA encoded disc is first inserted,
PlayingꢀanꢀMP3/WMAꢀDisc
“READING” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
Press DISP to select between track number/elapsed time
(default), clock, track name, directory name, title, artist and
album.
DisplayingꢀInformation
“NO IDꢁ TAG” will be displayed if the MPꢁ file contains no
IDꢁ tag information.
ꢀꢀ
“UNKNOWN” will be displayed if the WMA file contains no
WMA tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
This icon will illuminate when the album name is displayed.
This icon will illuminate when the folder name is displayed.
ꢀTitleꢀIconꢀꢀ
ArtistꢀIconꢀꢀ
AlbumꢀIconꢀꢀ
FolderꢀIconꢀꢀ
Maximum character display information
• Track name – ꢁꢀ character maximum
• Directory name – ꢀꢁ character maximum
• *Song title – ꢁ0 character maximum
• *Artist name – ꢁ0 character maximum
• *Album name – ꢁ0 character maximum
CharacterꢀSupport
*Song title, Artist Name and Album name will only be
displayed if included with the MPꢁ/WMA file.
When referring to MPꢁ/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name
11
XHD6420ꢀOPERATIONꢀ
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
Refer to the following button function table when selecting, searching or
navigating MPꢁ/WMA files and folders:
MP3/WMAꢀButtonꢀFunctionꢀTable
Button
Function
SEARCH
Direct Select, Search and Navigate Modes
Enter/Confirm
A, B, C, 1
Preset #1
Preset #ꢀ
D, E, F, ꢀ
Preset #ꢁ
G, H, I, ꢁ
Preset #4
J, K, L, 4
Preset #5
M, N, O, 5
Preset #6
P, Q, R, 6
Key #7
S, T, U, 7
Key #8
V, W, X, 8
Key #9
Y, Z, /, 9
Key #0
-, _, +, 0
Rotary Encoder (push)
Rotary Encoder (rotate)
MUTE
Character Shift
Character Select (A, B, C ~ 8, 9, 0)
Character Backspace
DirectꢀSelect,ꢀSearchꢀandꢀ
NavigateꢀModesꢀ
Press SEARCHꢀfor more than ꢁ seconds, to select between
the following modes:
• Direct File Select
• Alphanumeric File or Folder Search
• File or Folder Navigate
DirectꢀFileꢀSelect
Stepꢀ1
Press SEARCHꢀfor more than ꢁ seconds, then release.
“MPꢁ T " or “WMA T ” will flash in the display. Use the
*
*
buttons in the above table (ꢁ keystroke maximum input),
or the rotary encoder to enter the desired file number.
Stepꢀ2
Press
to confirm the selected file number or wait for
the input cycle to time out (approximately 5 seconds).
If the file is not available, “NO FILE” will be displayed
momentarily and the current file will continue to play.
1ꢀ
XHD6420ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
AlphanumericꢀFileꢀ Press SEARCHꢀfor more than ꢁ seconds, then release.
ꢀorꢀFolderꢀSearch Press SEARCHꢀagain, an " " will flash in the display.
*
Stepꢀ1 Use the buttons in the table on page 1ꢀ (ꢁꢀ character
maximum input) or the rotary encoder to enter the desired
alphanumeric search characters. Pressꢀthe rotary encoder
to advance one character to the right.
Stepꢀ2 Press
to initiate the selected alphanumeric search.
Stepꢀ3 Turn the rotary encoder to preview the search results.
If the search returns a folder, the icon will illuminate.
Stepꢀꢀ4 Press
to select the desired file or folder. If a folder is
selected, "/ꢀ/" will be displayed. Turn the rotary encoder to
the right to begin searching files in the folder.
Stepꢀ5 Press
Note:
to select the desired file within the folder.
If the file is not available, “NO FILE” will be displayed
momentarily and the current file will continue to play.
File/FolderꢀNavigate Press SEARCHꢀfor more than ꢁ seconds, then release.
Stepꢀ1 Press SEARCHꢀagain two times to navigate files/folders
on the disc. The current folder name will scroll one time
followed by available files and folders.
Stepꢀ2 Turn the rotary encoder to preview files/folders in the
current folder. If a folder is selected, the
illuminate.
icon will
Stepꢀ3 Press
to select the desired file or folder. If a folder is
selected, "/ꢀ/ꢀ" will be displayed. Turn the rotary encoder to
the right to begin searching files in the folder.
Stepꢀ4 Press
to select the desired file within the folder.
*FolderꢀAccess When navigating folders (and “/ꢀ/“ is displayed), press MUTEꢀ
(Upꢀꢀoneꢀlevel)ꢀ to access the previous level (up one level).
*Only available on MPꢁ/WMA discs recorded with more
than one folder.
1ꢁ
XHD6420ꢀOPERATIONꢀ
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
NavigatingꢀNote
*FolderꢀAccessꢀ
FileꢀRepeat
After navigating by direct select, alphanumeric search or
file/folder navigate modes, the track number and elapsed
time will be displayed by default. Press DISP momentarily
to select clock, track name, directory name, title, artist and
album.
Press
Press
to select the previous folder.
to select the next folder.
*Folder access is only available on MPꢁ/WMA discs recorded
with more than one folder.
Press RPT momentarily to continuously repeat selected file.
Press RPT again to cancel.
FileꢀRepeat
Press RPT for more than ꢀ seconds to consecutively repeat
(CurrentꢀFolderꢀOnly)
all files in the current folder only. The
the display when in folder repeat mode.
Press RPT again to cancel.
icon will appear in
DiscꢀRandom
Press RDM momentarily to play all files on entire disc in
random order. Press RDM again to cancel.
FolderꢀRandom
Press RDM for more than ꢀ seconds to play all files in
current folder only in random order. The
in the display when in folder random mode.
Press RDM again to cancel.
icon will appear
DiscꢀIntro
Press INT momentarily to play the first 10 seconds of each
file on the entire MPꢁ/WMA disc. Press INT again to cancel.
FolderꢀIntro
Press INT for more than ꢀ seconds to play the first 10
seconds of each file in the current folder only. The
will appear in the display when in folder intro mode.
Press INT again to cancel.
icon
Note:
File repeat (current folder only), folder random and folder
intro is only available on MPꢁ/WMA discs recorded with
more than one folder.
14
XHD6420ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
MediaꢀCompatibility The following types of discs/files are compatible:
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA
• MPꢁ data
• WMA data
The following types of discs/files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• Discs recorded with Track At Once or packet writing
• MPꢁ PRO format
• MPꢁ playlists
• WAV format
PlaybackꢀOrder MPꢁ/WMA playback sequence is based on recorded order
of files and begins in the root folder of the disc. Any empty
folders or folders that do not include MPꢁ/WMA files are
skipped. This unit may not play files in the order they were
recorded in. Refer to your recording software’s user’s
manual for more information.
CompatibleꢀRecordingꢀ • ISO9660 level 1
Formats • ISO9660 level ꢀ
• Yellow Book MODE 1
• Yellow Book MODE ꢀ FORM 1
• Multi session
• Maximum folders and files - ꢀ56
• Maximum folder levels - 8
• MPEG-1/ꢀ/ꢀ.5 Audio Layer-ꢁ
ISO9660 standards:
• Maximum nested folder depth is 8 (including the root
folder).
• Valid characters for folder/file names are letters A-Z
(all caps), numbers 0-9, and “_” (underscore). Some
characters may not be displayed correctly, depending on
the character type.
• This device can play back discs in Joliet, Romeo, and other
standards that conform to ISO9660. MPꢁ/WMA written in the
formats other than the above may not play and/or their file
names or folder names may not be displayed properly.
15
XHD6420ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
AdditionalꢀMP3/WMAꢀ An internal buffer provides ESP (Electronic Skip Protection) to
Information virtually eliminate skipping.
When playing a disc recorded with regular audio files
(CD-DA or .WAV) and MPꢁ/WMA files, the unit will play the
MPꢁ/WMA files only.
Only MPꢁ files with filename extension (.mpꢁ) can be played.
Only WMA files with filename extension (.wma) can be played.
Do not attempt to play discs which contain non-MPꢁ/WMA
files with the MPꢁ/WMA extension.
SamplingꢀFrequencyꢀRates
MP3 8kHz ~ 48kHz
WMA ꢁꢀkHz ~ 48kHz
TransferꢀBitꢀrates
MP3 ꢁꢀkbps ~ ꢁꢀ0kbps constant
Variable bit rates
WMA ꢁꢀkbps ~ 19ꢀkbps constant
Variable bit rates
Note:
Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3ꢀTagꢀDisplay IDꢁ tags Version 1.x
This model will not display IDꢁ Version ꢀ.0 or greater tags.
RecommendedꢀSettings For best results, use the following settings when burning an
MPꢁ disc:
1ꢀ8kbps or higher constant bit rate
44.1kHz or higher sampling frequency
For best results, use the following settings when burning a
WMA disc:
64kbps or higher constant bit rate
ꢁꢀkHz or higher sampling frequency
16
XHD6420ꢀOPERATION
LimitedꢀOneꢀYearꢀWarranty
This warranty gives you specific legal rights.
You may also have other rights which vary from
state to state.
Whatꢀtoꢀdo?
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls may save you a service call.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.
ꢀ. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
in material or workmanship or to furnish an
equal new, renewed or comparable product
(whichever is deemed necessary) in exchange
without charges, subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.
ꢁ. Please describe your problem in writing and
include your name, a return UPS shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.
4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:
Whoꢀisꢀcovered?ꢀThis warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A.
• Call us toll-free at 1-866-ꢁ8ꢀ-5476
• E-mail us at [email protected]
Whatꢀisꢀcovered?ꢀThis warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
line voltage, unauthorized repair or failure to
follow instructions supplied with the product,
or damage occurring during return shipment of
the product.
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect, incidental or consequential
damages.
17
XHD6420ꢀOPERATION
Troubleshootingꢀ
Problem
Cause
Action
Yellow wire not connected or incorrect voltage Check connections for proper
Unitꢀwillꢀnotꢀturnꢀonꢀ
(noꢀpower)
Red wire not connected or incorrect voltage
Black wire not connected
Fuse blown
voltage (11~16VDC)
Check connection to ground
Replace fuse
Speaker wires not connected
Check connections at speakers
Unitꢀhasꢀpowerꢀ
(butꢀnoꢀsound)
One or more speaker wires touching each
other or touching chassis ground
Insulate all bare speaker wires from
each other and chassis ground
Yellow or red wire touching chassis ground
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Check for pinched wire
Use fuse with correct rating
Unitꢀblowsꢀfuses
Unit is not mounted correctly or backstrap is
not secure
Check mounting sleeve and
backstrap support
Excessiveꢀskipping
Physical defect in media (CD, CD-R or CD-RW) Check media for scratches
ERROR-01ꢀappearsꢀ
onꢀdisplay
Disc read error
Press EJECT or RESET
ERROR-02ꢀappearsꢀ
onꢀdisplay
Focus error or disc is in upside down
Press EJECT or RESET
PROTECTꢀappearsꢀ
onꢀdisplay
The WMA file is copy-protected by DRM
(Digital Rights Management)
Write disc using WMA files that are
not copy-protected
NOꢀFILEꢀappearsꢀ
onꢀdisplay
Selected file is not available in direct or
alphanumeric search modes
Repeat search using valid
parameters
INVALIDꢀappearsꢀ
onꢀdisplay
The file format is incompatible
Write disc using valid audio files
with .mpꢁ or .wma file extensions
CD mechanism position out of alignment
CD transit screws still in place
Press and hold EJECT for ꢁ seconds
to reset CD mechanism position
Unitꢀwillꢀnotꢀacceptꢀ
aꢀdisc
Remove ꢀ transit screws located on
top of the unit
An invalid IDꢁ tag version is present
Version 1.x IDꢁ tags are supported.
Version ꢀ.0 or greater are not
supported
NOꢀSUPPORTꢀappearsꢀonꢀ
display
18
XHD6420ꢀOPERATION
Specifications
CDꢀPlayer Frequency response: 10Hz-ꢀ0kHz
Channel separation @ 1kHz: >65dB
D/A converter: 1 Bit
FMꢀTuner Tuning range: 87.5MHz-108.1MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
HD radio stereo separation @ 1kHz: 85dB
Frequency response: ꢁ0Hz-1ꢁkHz
HD radio frequency response: ꢁ0Hz-ꢀ0kHz
AMꢀTuner Tuning range: 5ꢁ0kHz-1710kHz
Usable sensitivity: ꢀꢀuV
Frequency response: ꢀ40~ꢁKHz
HD radio frequency response: ꢁ0~4.4KHz
HD radio stereo separation @ 1kHz: 85dB
General Operating voltage: 11-16 VDC, negative ground
Speaker output impedance: 4~8 ohms
Line output voltage: ꢀ Volts
Dimensions: 7" x 7" x ꢀ" (178 x 178 x 51 mm)
Design and specifications subject to change without notice.
CEA-ꢀ006 Power Standard Specifications
(reference: 14.4VDC +/- 0.ꢀV, ꢀ0Hz~ꢀ0kHz)
Power Output: 17 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
19
Dual Electronics Corp.
Toll Free: 1-866-ꢁ8ꢀ-5476
©ꢀ007 Dual Electronics Corp. All rights reserved.
Windows Media and the Windows logo are trademarks, or registered trademarks of
Microsoft Corporation in the United States and or other countries.
HD Radio™ Technology Manufactured Under License from iBiquity Digital Corporation. U.S. and Foreign
Patents. HD Radio™ and the HD Radio logo are proprietary trademarks of iBiquity Digital Corp.
Other trademarks and trade names are those of their respective owners.
NSA0807-V0ꢀ
|