PUB. DIE-0429-002
HD Camcorder
Instruction Manual
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage”
within the product’s enclosure, that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The exclamation point, within an equilateral triangle, is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.
3
Only for European Union and EEA (Norway, Iceland and Liechtenstein)
These symbols indicate that this product is not to be disposed of with your household
waste, according to the WEEE Directive (2012/19/EU), the Battery Directive (2006/66/EC)
and/or national legislation implementing those Directives.
If a chemical symbol is printed beneath the symbol shown above, in accordance with the
Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in
this battery or accumulator at a concentration above an applicable threshold specified in the Battery
Directive.
This product should be handed over to a designated collection point, e.g., on an authorized one-for-one
basis when you buy a new similar product or to an authorized collection site for recycling waste electrical
and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste
could have a possible impact on the environment and human health due to potentially hazardous
substances that are generally associated with EEE. Your cooperatioin the correct disposal of this product
will contribute to the effective usage of natural resources.
For more information about the recycling of this product, please oact your local city office, waste
authority, approved scheme or your household waste al servior visit
www.canon-europe.com/weee, or www.canon-europattery.
Important Safety Instructions
In these safety instructions the word “apparatus”
refers to the Canon HD Camcorder EOS C100 and
all its accessories.
A grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
4
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
11. Only use attachments/accessories specified by
the manufacturer.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
12. Unplug this apparatus during lightning storms or
when unused for long periods of time.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
13. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objes have fallen into the apparatus, the
apras has been exposed to rain or moisture,
oes noperate normally, or has been dropped.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other.
CAN B)/NB-3(B)
Trademark Acknowledgements
• SD, SDHC and SDXC Logos are trademarks of SD-3C, LLC.
• Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• Apple, Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
• “AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony
Corporation.
• Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
• Other names and products not mentioned above may be trademarks or registered trademarks of their
respective companies.
• This device incorporates exFAT technology licensed from Microsoft.
• ANY USE OF THIS PRODUCT OTHER THAN CONSUMER PERSONAL USE IN ANY MANNER THAT
COMPLIES WITH THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED
MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2
PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, L.L.C., 250 STEELE STREET,
SUITE 300, DENVER, COLORADO 80206.
• This product is licensed under AT&T patents for the MPEG-4 standard and may be used for encoding
MPEG-4 compliant video and/or decoding MPEG-4 compliant video that was encoded only (1) for a personal
and non-commercial purpose or (2) by a video provider licensed under the AT&T patents to provide MPEG-4
compliant video. No license is granted or implied for any other use for MPEG-4 standard.
Highlights of the EOS C100
The Canon HD Camcorder EOS C100 is a versatile camcorder that combines the power of our latest CMOS
sensor and interchangeable lenses with the convenience of a compact size. The following are just some of the
many features that will help turn your creative vision into reality.
5
you record the same clip simultaneously to both SD
cards.
HD Recording
Large Super 35mm CMOS sensor and DIGIC DV
III image processor
Enhanced automatic functions
The camcorder is equipped with a large Super
35mm CMOS sensor that captures video at an
effective pixel count of 8.29 megapixels
(3840x2160). Combined with the DIGIC DV III image
processor, the camcorder offers a center resolution
of 1,000 TV lines*. Furthermore, thanks to its fast
scanning speed, the camcorder produces
spectacular video with true-to-life color reproduction
while reducing noise and “rolling shutter” artifacts.
* Varies depending on the lens used.
The camera features a variety of automatic functions
to support a simple one-person operation. These
include automatic aperture and push auto iris
as you press and hold the button, automatic white
adjust the optimal white balance setting, and
camcorder focus automatically one time.
Interchangeable lenses
Enjoy the freedom and creative versatility of using
interchangeable lenses to achieve exactly the look
you want. The camcorder features an EF lens mount
allowing you to use a huge variety of high-qualit
Canon EF lenses, including the new high-end C
Cinema lenses, as well as other lenses
rsatilArtistic Expression
tom picure settings
uparalleled image control to deliver the look you
want by adjusting parameters, such as gamma and
color matrix. The camcorder also features a new,
easy interface that lets you adjust the gamma curve
and white balance using an intuitive graph. The
custom picture settings can be saved onto an SD
card, which allows multiple C100 camcorders to use
the same settings.
Superb HD video
The camcorder offers you a whole arraof optns
when it comes to the video configuration our
recordings. By controlling the system frequency
(50.00 Hz recordings or 59.94 Hz recordings), bit
rate, resolution and frame rate of your recordings
you can select a video configuration to suit your
needs from a total of 24 different combinations.
recordings
You can easily apply the [/ CINEMA Locked]
preset settings, especially designed with
professional cinematography in mind. The Canon
Log gamma makes the most of the newly-
developed image sensor to achieve amazing
dynamic range, allowing you to realize in post-
production the artistic vision you desire.
Operability and Adaptability
Freely customizable compact design
At its most compact configuration, the camcorder
offers convenient and hassle-free hand-held
operation. Modular components let you expand
your options. The handle unit, for example, adds
advanced audio capabilities allowing for simple one-
Recording media
The camcorder supports all the latest types of
Secure Digital (SD) cards. You can even make
lengthy recordings without worry because the
camcorder features two SD card slots. When one
SD card becomes full, the recording will
automatically continue on the other one when you
Advanced Professional Features
Other Functions
Customization
Audio
The camcorder features several customization
options. You can assign often-used functions to
those functions with the press of a single button. You
can also register frequently-used menu settings in an
control many aspects of the camcorder’s operation.
Save custom picture and menu settings to an SD
preferences to other C100 camcorders in order to
use them in the same way.
When recording at the highest bit rate, you have the
option to record sound as 2-channel linear PCM
audio (16-bit/48 kHz). You can use the built-in
microphone, ∅ 3.5 mm MIC terminal or the two XLR
audio input terminals (with phantom power supply)
when recording.
6
LCD screen and viewfinder
The LCD screen and viewfinder both have 100%
frame coverage, which will ensure that you can
accurately check that your shots are framed how you
want them.
Video scopes
Check the brightness of the image using the
Time code/User bit output
The internal camcorder-generated time code can be
output from the HDMI OUT terminal for easy logging
Added and improved functionality
Other functions include the ability to down-convert
your recordings to standard definition (MPEG-2) in
Table of Contents
7
Video Configuration: System Frequency, Bit Rate
Changing Main Camera Functions with the
Momentary Automatic Aperture - Push Auto
SD Cards Compatible for Use with the
Checking the Remaining Recording Time on the
8
Connecting an External Microphone or External
Using the Built-in Microphone or an External
Terminal 74
Adjusting the Audio Level for the XLR
Superimposing Onscreen Displays to Appear on
Synchronizing the Video with the Audio being
Selecting the Output Level of the AV OUT
Resetting the current file’s settings to default
Customizing Functions and Onscreen
10
Introduction
1
11
About this Manual
Thank you for purchasing the Canon EOS C100. Please read this manual carefully before you use the camcorder
and retain it for future reference. Should the camcorder fail to operate correctly, refer to Troubleshooting
Conventions Used in this Manual
•
•
IMPORTANT: Precautions related to the camcorder’s operation.
NOTES: Additional topics that complement the basic operating procedures.
• A: Reference page number.
• The following terms are used in this manual.
“Screen” refers to the LCD screen and the viewfinder screen.
“SD card” refers to an SD, SDHC or SDXC card.
• Photographs in the manual are simulated pictures taken with a amera. Some screenshots have been
altered to make them easier to read.
• Illustrations in the manual show the Canon EOS C100 rder with a Canon EF 24-70mm f/2.8 L II USM
lens attached.
About this Manual
The > arrow is used to abbreviate menu
selections. For a detailed explanation on how to
use the menus, refer to Using the Menus
menu options and settings, refer to the appendix
Operating modes
indicates that a function is available in the
operating mode indicated and indicates
that the function is not available. For a detailed
explanation, refer to Turning the Camcorder On
12
Setting the Time Code
The camcorder generates a times code signal and embeds it in your recordings. You can output the time code
along with video output from the HDMI OUT terminal (A 134). For 59.94 Hz recordings, you can also select
between a drop frame and non-drop frame time code.
Operating modes:
Selecting the Running Mode
[¤ TC/UB Setup]
You can select the running mode of the camcorders time code.
[Time Code]
1 Open the time code [Mode] submenu.
[¤ TC/UB Setup] > [Time Code] > [Mode]
[Mode]
2 Select the desired option and then press the joystick.
€ If you selected [Regen.], you do not need to perform the rest of this
procedure. If you selected [Preset] and would like to set the time
[Preset]
code s initial value, see the following section Setting the Time
Initial Value.
[¤ C/UB Setup]
3 After you select [Preset], open the time code [Run] sub
[¤ TC/UB Setup] > [Time Code] > [Run]
[Time Code]
4 Select the desired option and then pres
[Run]
Options
[Preset]: The time code starts frn initial v
advance. The defanitial tcode time
codes running mdepends on the [R
[Rec Run]: The timode runs only while relips
recordensecutively ohe same SD card will have
continuome codes.
[Rec Run]
[Free Run]:The time coarts rug the moment you press
the joystick to soption and keeps running
regardless of the camcorder s operation.
[Regen.]: The camcorder will read the selected SD card and the time code
will continue from the last recorded time code on the SD card.
The time code runs only while recording so clips recorded
consecutively on the same SD card will have continuous time
codes.
Setting the Time Code s Initial Value
[¤ TC/UB Setup]
[Time Code]
If you set the time code mode to [Preset], you can set the initial value of
the time code.
1 Open the time code [Setting] submenu.
[¤ TC/UB Setup] > [Time Code] > [Setting]
2 Select [Set] and then press the joystick.
[Setting]
€ The time code setting screen appears with an orange selection frame
indicating the hours.
When a procedure requires selecting an option,
When a function requires the use of the menu,
the quick reference shows the submenus and,
when applicable, the default setting for the menu
item. The example illustration indicates that you
can find the function by selecting the
the available options are listed within or after the
procedure. Brackets [ ] are used to refer to menu
options as they are displayed on screen.
[¤ TC/UB Setup] menu and then the
[Time Code] menu item.
Supplied Accessories
Supplied Accessories
The following accessories are supplied with the camcorder.
13
Handle Unit
Grip Unit1
BP-955 Battery Pack
(incl. terminal cover)
CA-930 Compact Power Adapter
(incl. power cord)
Body Cap1
Thumb Rest
SS-1200 Shoulder Strap
DC-930 DC Cable
Adapter Base for 0.64 cm (1/4 in.)
Tripods
Tapeasure Hook1
PIXELA Software CD-ROM2
1
2
Comes pre-attached to the camcorder.
Use Data Import Utility to transfer your clips to a computer. Refer to Saving Clips to a Computer (A 123). The CD-ROM
includes the instruction manual of the software (on PDF file).
Names of Parts
15
17
18
19
20
21
24
25
26
22
23
27
20 REMOTE terminal
For connecting commercially availae reme
controllers.
Names of Parts
16
29
30
31
32
33
34
35
28
36
35 NE-SHOT AF (focus automatically once) button
Names of Parts
LCD panel fully open
LCD panel raised 90° up and turned left
38
37
17
39
40
53
54
55
56
46
47
48
49
50
41
57
58
51
52
42
43 44 45
51 SD card compartment cover
43 Battery compartment
44 SLOT SELECT (SD card slot selection) button
Names of Parts
18
60
59
59
Focal plane mark
60 Accessory shoe with mounting hole for
0.64 cm (1/4 in.) screws
Cold shoe for attaching the supplied handle unit or
other accessories, such as the optional
VL-10Li II Battery Video Light.
63
64
61
62
61 TB-1 Tripod Base for tripods with 0.95 cm (3/8 in.)
63 Attachment sockets for the optional TA-100 Tripod
Names of Parts
Grip Unit
The grip unit comes originally attached to the camcorder. If the grip unit is removed, you will not be able to use
the joystick, but you can set the joystick's functions (up/down/left/right/SET) to assignable buttons (A 89) to be
able to change settings that require the joystick*.
When the grip unit is not attached, the control dial (A 60, 61) and MAGN. button/Assignable button 7 (A 89)
cannot be used to operate the camcorder either.
* Except during photo playback. Functions that require the joystick include all settings in the menus (A 27, 133), white balance,
19
6
1
2
3
4
5
7
8
1
2
3
4
5
6
7
8
Names of Parts
Handle Unit
1
2
3 4 5
20
6
7
8
9
16
17
10
12
11
14
15
1
2
3
4
5
6
7
8
9
Cold accessory shoe
Mounting hole for 0.64 cm (1/4 in.) screws
13 Audio level switches for CH1 (left) and CH2 (right)
14 XLR terminal switches for CH1 (left) and CH2
15 AUDIO IN (audio input selection) switches for CH1
10 Protective cover for audio controls
12
(audio level) dials for CH1 (left) and CH2
Preparations
2
21
Preparing the Power Supply
You can power the camcorder using a battery pack or directly using the compact power adapter. If you connect
the compact power adapter to the camcorder while a battery pack is attached, the camcorder will draw power
from the power outlet.
Charge battery packs before use. For approximate charging times and recording/playback times with a fully
Using a Battery Pack
You can power the camcorder using the supplied BP-955 or an optional BP-950G, BP-970G or BP-975 Battery
Pack. The BP-955 and BP-975 are compatible with Intelligent System, meaning that you can check the
remaining battery time.
Charging the Battery Pack
Charge battery packs using the supplied DC-930 Compawer Adpter.
Before charging, disconnect the DC cable from the comwer adter
and remove the terminal cover of the battery pa
1 If the DC cable is connected to the compact aptedisconnect it.
• Charging will not start while the Dcable is d to the compact
power adapter.
2 Connect the power cord to the compct poer adapter.
3 Plug the power cord into a power outlet.
CHARGE indicator
4 Attach the battery pack to the compact power adapter.
• Press lightly and slide the battery pack in the direction of the arrow until it clicks.
• The CHARGE indicator starts flashing and also indicates the battery pack’s approximate charge. The
indicator will stay on when charging has completed.
0-34%: Flashes once per second
35-69%: Flashes twice per second
70-99%: Flashes 3 times per second
5 When charging has completed, remove the battery pack from the compact power adapter.
6 Unplug the power cord from the power outlet and disconnect it from the compact power adapter.
IMPORTANT
• Do not connect to the compact power adapter any product that is not expressly recommended for use with this
camcorder.
NOTES
• We recommend charging the battery pack in temperatures between 10 ºC and 30 ºC (50 ºF and 86 ºF).
Outside the temperature range of 0 ºC to 40 ºC (32 ºF to 104 ºF), charging will not start.
• If there is a malfunction with the compact power adapter or battery pack, the charge indicator will go out and
charging will stop.
Preparing the Power Supply
• Charged battery packs continue to discharge naturally. Therefore, charge them on the day of use, or the day
before, to ensure a full charge.
• We recommend that you prepare battery packs to last 2 to 3 times longer than you think you might need.
• To charge the battery pack, disconnect the DC cable from the compact power adapter.
22
Attaching the Battery Pack
1 Set the Q switch to OFF.
2 Insert the battery pack all the way into the compartment as shown
in the illustration and press it gently toward the left until it clicks.
Removing the Battery Pack
1 Set the Q switch to OFF.
2 Push the BATTERY RELEASE latch in the direction of the arrow.
While holding it down, slide the battery pack toward the right and
then pull it out.
Preparing the Power Supply
Checking the Remaining Battery Charge
When the camcorder is turned on, you can check the remaining battery charge by looking at any recording/
playback screen or the [Battery/Hour Meter] status screen (A 144). When the camcorder is turned off, use one
of the following methods to check the approximate remaining battery charge of a battery compatible with
Intelligent System.
23
Press the CHECK button on the battery pack. An indicator will light for
approximately 3 seconds and show the approximate remaining battery
charge.
0-25%
CHECK button
26-50%
51-75%
76-100%
0
100%
Battery charge indicator
Press the BATT. INFO button to display the approximate remaining
battery charge for about 5 seconds. Depending on the battery life, th
battery information may not be displayed.
NOTES
• The first time you use a battery pack, fully charge it and then use the camcorder until the battery pack is
completely exhausted. Doing so will ensure that the remaining recording time will be displayed accurately in
the various recording/playback screens.
• Repeatedly charging and discharging the battery pack will eventually shorten its battery life. You can check the
battery life on the [Battery/Hour Meter] status screen (A 144) or the battery information screen (press the
BATT. INFO button while the camcorder is turned off). Fully charging the battery pack and then discharging it
will give you a more accurate reading.
• USA and Canada only: The Lithium ion/polymer battery that powers the product is recyclable.
Please call 1-800-8-BATTERY for information on how to recycle this battery.
Preparing the Power Supply
Using a Household Power Outlet
You can also power the camcorder directly
from a power outlet using the supplied CA-930
Compact Power Adapter and DC-930 DC
Cable.
24
1 Set the Q switch to OFF.
2 Connect the DC cable to the DC IN
terminal on the camcorder.
3 Connect the power cord to the compact
power adapter and plug it into a power
outlet.
4 Connect the DC cable to the compact
power adapter.
IMPORTANT
• Turn off the camcorder before connecting or
disconnecting the compact power adapter.
DC IN
terminal
NOTES
• When using the camcorder with a household
power outlet, you can change the battery pack while the r is on.
Turning the Camcorder On anOff
The camcorder has two operating modeCAMRA (
) mode for making recordings and MEDIA (
)
mode for playing back recordings. Select the operating mode using the Q switch.
To turn on the camcorder
Set the Q switch to CAMERA for
mode or MEDIA for
mode.
CAMERA mode
MEDIA mode
To turn off the camcorder
Set the Q switch to OFF.
Date, Time and Language Settings
Date, Time and Language Settings
Setting the Date and Time
You will need to set the date and time of the camcorder before you can start using it. When the camcorder’s
clock is not set, the [Date/Time] screen will appear automatically with the first field selected (month or day,
depending on the country/region of purchase).
25
Operating modes:
1 Push the joystick up/down to change the month/day then push it right to move to the next field.
• To move to the next field you can also press the joystick itself.
2 Change the rest of the fields in the same way.
3 Select [Set] and then press the joystick to start thk and ose the screen.
NOTES
• You can change the date format and the cloc12/2hours) with the [w Other Functions] > [Set
Clock] > [Date Format] setting.
• You can also change the date and te later on (not during the initial setup) with the [w Other Functions] >
[Set Clock] > [Date/Time] setting.
• When the built-in rechargeable lithium battery is exhausted, the date and time setting may be lost. In such
Changing the Time Zone
[w Other Functions]
Change the time zone to match the time zone of your location. The default
setting is [UTC-05:00 New York] or [UTC+01:00 Central Europe],
depending on the country/region of purchase. The time zones are based
[Time Zone]
on Coordinated Universal Time (UTC).
[UTC-05:00 New York]
or
Operating modes:
[UTC+01:00 Central Europe]*
1 Press the MENU button.
* Depending on the country/region
of purchase.
2 Push the joystick up/down to select [w Other Functions].
3 Select [Time Zone] in a similar fashion.
4 Push the joystick up/down to change the time zone.
5 Press the joystick to set the time zone and then press the MENU button to close the menu.
Date, Time and Language Settings
Displaying the Date and Time while Recording
[£ LCD/VF Setup]
[Custom Display 2]
[Date/Time]
You can display the date and time on the screen.
Operating modes:
26
1 Press the MENU button.
2 Push the joystick up/down to select [£ LCD/VF Setup].
[Off]
3 Select [Custom Display 2] and then [Date/Time] in a similar
fashion.
4 Push the joystick up/down to select the information to display.
• Select [Off] to record without displaying the date and time.
5 Press the joystick and then press the MENU button to close the menu.
• The selected date/time display will appear at the bottom left of the screen.
Changing the Language
[w Other Functions]
[Language !]
[English]
The default language of the camcorder is English. You can change it to
German, Spanish, French, Italian, Polish, Russian, Simplified Chinese,
Korean or Japanese. Please note that some settings and screens w
displayed in English, regardless of the language setting.
Operating modes:
1 Press the MENU button.
2 Push the joystick up/down to selet [w Other Functions].
3 Select [Language !] in a similar fasio
4 Push the joystick up/down to select a language.
5 Press the joystick to change the language and then press the MENU button to close the menu.
Using the Menus
Using the Menus
In
opens after pressing the MENU button. You can also register frequently used menu settings in a customized
submenu (My Menu) for easy access. In mode, press the MENU button to open the menu for general
mode, many of the camcorder’s functions can be adjusted from the menu for general settings, which
27
settings or press the joystick to open the clip menu for clip operations. For details about the available menu
Operating modes:
CANCEL button
Press to return to the previous menu or to stop some
operations that are in progress.
MENU button
Press to open the menu and then press again to close
the menu after adjusting desired settings.
Joystick
Push the joystick to move the orange selection frame in
the menu. Then, press the joystick itself to select the
menu itindicated by the orange selection frame.
Selecting an Option from the Menu
The following is a step-by-step explanation of hect option from the menu. In the procedures
throughout the rest of this manual, oping and e menu is assumed and not included in the procedure.
1 Press the MENU button.
• The menu opens with the orange seltioframe indicating the menu item that was selected the previous
time the menu was closed (unless the camcorder was turned off).
2 Push the joystick up/down to select the desired submenu.
3 Push the joystick right or press the joystick.
• The orange selection frame will appear on a menu item in the submenu.
• Press the CANCEL button, push the joystick left, or select [L] to return to the previous submenu.
4 Push the joystick up/down to select the desired menu item.
• If a submenu contains many menu items, a scroll bar will appear on the right side of the submenu indicating
that you must scroll up or down to see other menu items.
• A Ð mark next to a menu item indicates another submenu. Repeat steps 3 and 4.
5 Push the joystick right or press the joystick.
• The orange selection frame will appear on a setting option.
• Press the CANCEL button to return to the previous submenu.
6 Push the joystick up/down to select the desired setting option and then press the joystick.
• Depending on the menu item, additional selections may be necessary.
7 Press the MENU button to close the menu.
NOTES
• Unavailable items may appear grayed out.
• Pressing the MENU button at any time closes the menu.
Using the Menus
• When an optional RC-V100 Remote Controller is connected to the camcorder, you can use the remote
controller's Up/Down/Left/Right/SET buttons in the same way as the camcorder's joystick. Pressing the SET
button is equivalent to pressing the joystick on the camcorder.
28
Using the Customized Submenu (My Menu)
You can register up to 14 frequently used menu settings under the My Menu submenu for easy access.
Furthermore, if you set an assignable button to [My Menu] (A 89), you can press the button to access your
registered menu settings even faster and more easily.
Adding Menu Settings
[
My Menu]
[Edit]
1 Open the My Menu [Register] screen.
My Menu] > [Edit] > [Register]
[
• The menu will change to blue to indicate you are selecting menu
settings to add to the My Menu submenu.
[Register]
• Select [Cancel] to cancel the operation.
2 Navigate the menus to find the menu setting you want to add and tn
press the joystick.
3 Select [OK] and then press the joystick twice.
• The menu setting you registered will now appear undeMy Mensubmenu.
Rearranging Menu Settings
[
My Menu]
[Edit]
1 Open the My Menu [Move] screen.
[
My Menu] > [Edit] > [Move]
2 Push the joystick up/down to select the setting you want to move and
then press the joystick.
[Move]
• An orange icon will appear next to the setting you selected to
move.
3 Push the joystick up/down to move the setting to the desired position and then press the joystick.
Removing Menu Settings
[
My Menu]
1 Open the My Menu [Delete] screen.
My Menu] > [Edit] > [Delete]
[
[Edit]
2 Push the joystick up/down to select the setting you want to remove and
then press the joystick.
[Delete]
3 Select [OK] and then press the joystick twice.
Resetting the My Menu Submenu
[
My Menu]
[Edit]
1 Reset all the menu settings registered to the My Menu submenu.
[
My Menu] > [Edit] > [Reset All]
2 Select [OK] and then press the joystick twice.
[Reset All]
Preparing the Camcorder
Preparing the Camcorder
This section outlines the basic preparations for the camcorder such as attaching a lens and attaching the
modular units (handle unit, grip unit, etc.) to the camcorder. The modular units extend the camcorder's
functionality so you can choose the configuration that best fits your needs and shooting conditions.
29
Configuration with handle:
Attach the handle unit to
use the built-in microphone,
XLR terminals, microphone
Light configuration with grip
for hand-held shooting.
Minimal configuration with thumb resYou will not be able to use the joystick,
but you can set the joystick's funcon(up/down/left/right/SET) to assignable
be used to operacamder.
* Except durig phoFunons that require the joystick include all settings in the
Preparing the Lens
As much as possible, attach and remove the lens quickly and in a clean environment free of dust. Refer also to
the instruction manual of the lens used.
IMPORTANT
• When attaching/removing a lens, avoid direct sunlight or strong light sources. Also, be careful not to drop the
camcorder or lens.
NOTES
• Be careful not to touch the lens mount or any components inside the lens mount area.
• Replace the body cap to the lens mount immediately after removing the lens from the camcorder.
• Keep the body cap clean and free from dust or dirt particles.
Preparing the Camcorder
Attaching an EF Lens
1 Set the Q switch to OFF.
2 Remove the body cap from the camcorder and any dust
caps from the lens.
30
3 Attach the lens to the camcorder and turn the lens in the
direction of the arrow until it clicks in place.
• EF lenses: Align the red mark on the lens with the red
EF Lens mount index mark on the camcorder.
• EF-S lenses: Align the white mark on the lens with the
white EF-S Lens mount index mark on the camcorder.
NOTES
• Turning on the image stabilization function of an EF lens may reduce the effective usage time of the battery
pack. When image stabilization is not necessary, for example if the camcorder is fixed to a tripod, it is
recommended to turn it off.
• On some EF lenses equipped with autofocus (AF) function, the focus ring will be disabled when the focus
mode switch is set to AF. In such case, set the focus mode switch to MF.
• Depending on the lens used, you may experience one or more of thfollowing limitations.
- The lens model name may be shortened when displayed on thseen.
- You may not be able to use the focus preset function telephto lenses).
- You may not be able to use the power zoom function ens.
Removing an EF Lens
1 Set the Q switch to OFF.
2 Hold down the lens release button anturn tlens all the
way in the direction of the arrow until it st
3 Remove the lens and replace the body cap to the
camcorder and the dust cap to the lens.
Peripheral Illumination Correction
Depending on the characteristics of the lens used, the image
around the corners of the picture may seem darker due to light
fall-off or peripheral illumination drop. If the camcorder has
correction data available for the EF lens used, it can apply this
correction data to compensate as necessary.
Operating modes:
1 Attach the lens you want to use.
[~ Camera Setup]
2 Open the peripheral illumination correction screen.
[~ Camera Setup] > [Periph. Illum. Corr.]
[Periph. Illum. Corr.]
• If correction data is available, the lens model name will appear on the
screen.
[Off]
• If correction data is not available, [Periph. Illum. Corr.] will appear
grayed out. Visit your local Canon Web site and check if there is
correction data available for the lens you are using. If so, download the necessary update package and
upgrade the camcorder’s firmware following the instructions supplied therein.
Preparing the Camcorder
3 Select [On] and then press the joystick.
• As long as [~ Camera Setup] > [Periph. Illum. Corr.] is set to [On], the camcorder will automatically apply
the appropriate correction data.
31
Correction for EF-S Lenses
The peripheral illumination fall-off may be more pronounced with EF-S lenses than with EF lenses. To prevent
this, when you use an EF-S lens, you can change the sensor area that is used for producing the image.
Operating modes:
1 Open the [EF-S Lens] submenu.
[~ Camera Setup]
[~ Camera Setup] > [EF-S Lens]
2 Select [On] and then press the joystick.
[EF-S Lens]
•
will appear at the lower center of the screen.
• When [EF-S Lens] is set to [On], the image is enlarged digitally by a
factor of approximately 1.04x, slightly affecting the image quality. In
most cases, using the default [Off] setting is recommended.
[Off]
NOTES
• About lens correction data:
- The camcorder contains a register of correction data focompe lenses that were available at the time
the camcorder went on sale. Correction data for futes will e made available as part of the regular
updates released for the camcorder’s firmware. For metails, visit your local Canon Web site.
- Depending on the recording conditions, noappr in the periphery of the image as a result of the
correction.
- The level of correction will be lowfor lenses nnot provide distance information.
- The level of correction will be lowthe higher the ISO speed/gain setting used.
- No correction will be applied when rrecn data is not available for the lens attached.
- When using non-Canon lenses, peripheral illumination cannot be corrected. Even if the [Periph. Illum. Corr.]
setting is available (not grayed out), setting it to [Off] is recommended.
Updating the Firmware of an EF Lens
You can update the lens firmware of an EF lens using the camcorder. For details about firmware updates for EF
lenses, visit your local Canon Web site.
Operating modes:
1 Insert the SD card containing the lens firmware update into SD card
slot A.
[w Other Functions]
2 Attach to the camcorder the lens you wish to update and open the
[Lens Firmware] submenu.
[Lens Firmware]
[w Other Functions] > [Lens Firmware]
• The current lens firmware version will appear on the screen.
• If the [Lens Firmware] submenu is grayed out, the attached lens may not support firmware updates or the
SD card in SD card slot A may not contain a valid lens firmware file. Check the lens and SD card and repeat
the procedure from the beginning.
3 Select [OK] and then press the joystick.
4 Select the lens firmware file (file extension .LFU) and then press the joystick.
5 Select [OK] and then press the joystick.
• The lens firmware will be updated. Once in progress, the lens firmware update cannot be canceled.
Preparing the Camcorder
6 When the confirmation message appears, press the joystick.
IMPORTANT
• Be sure to observe the following precautions while the lens firmware is being updated.
- Do not disconnect the power source or turn off the camcorder.
- Do not remove the lens.
32
- Do not operate any buttons or controls on the camcorder.
- Do not open the SD card compartment cover and do not remove the SD cards.
NOTES
• The lens firmware cannot be updated while pre-recording is activated.
• We recommend that you power the camcorder from a household power outlet using the compact power
adapter or use a sufficiently charged battery pack.
• When using an optional EF Extender, remove the Extender before performing the procedure.
Attaching and Removing the Handle Unit
The handle unit extends the camcorder’s audio capabilities, adding Xterminals as well as a built-in stereo
microphone.
Attaching the Handle Unit
1 Set the Q switch to OFF.
2 Insert the attachment base at the bottm of th
unit to the camcorder’s accessory se.
3 Tighten the handle unit’s lock screw wile geny pressing
it down.
4 Connect the handle unit’s cable to the camcorder’s EXT
terminal, aligning the Í marks.
Removing the Handle Unit
1 Set the Q switch to OFF.
2 Disconnect the handle unit's cable.
• Pull back the metallic tip of the cable to release the
cable and then disconnect the cable from the terminal.
3 Loosen the handle unit's lock screw and gently slide out
the handle unit from the accessory shoe.
NOTES
• You can use the accessory shoe or the socket for 0.64 cm (1/4 in.) screws on the handle unit to attach a
variety of commercially available accessories.
Preparing the Camcorder
Using the Viewfinder
Dioptric Adjustment
Turn on the camcorder and adjust the dioptric adjustment
lever.
33
Dioptric
adjustment
lever
Using the LCD Panel
1 Pull the LCD panel 90° up.
2 Rotate the LCD panel 180° left.
3 Push down the LCD panel to adjust it to the desired angle of iew.
NOTES
• When you use a commercially available lens nd e image on
the screen is inverted, you can use the [w Otons] > [Custom
Function] > [Scan Reverse Rec] sting to retmage to the
correct orientation.
• If you are not interested in using the vwfindr along with the LCD
screen, you can set [£ LCD/VF Setup] > [LCD/VF Simul.] to [Off] to
conserve the camcorder’s power. Even when [LCD/VF Simul.] is set to
[Off], closing the LCD panel will automatically activate the viewfinder.
Adjusting the Viewfinder/LCD Screen
[£ LCD/VF Setup]
You can adjust the brightness, contrast, color, sharpness, and backlight
of the viewfinder and LCD screen independently of each other. These
adjustments will not affect your recordings.
[LCD Setup]
[VF Setup]
Operating modes:
[Brightness: 0]
[Contrast: 0]
[Color: 0]
[Sharpness: 2]
[Backlight: Normal]
1 Open the setup menu for the viewfinder or LCD screen.
[£ LCD/VF Setup] > [LCD Setup] or [VF Setup]
2 Select [Brightness], [Contrast], [Color], [Sharpness] or [Backlight]
and then press the joystick.
3 Adjust the setting and then press the joystick.
• Repeat steps 2 and 3 to adjust other settings as necessary.
NOTES
• If you set an assignable button to [LCD Setup] or [VF Setup] (A 89), you can press the button to open the
respective submenu.
Preparing the Camcorder
Setting the Screen to Black & White
[£ LCD/VF Setup]
[LCD/VF B&W]
[Off]
The viewfinder and LCD screen display in color by default but you can set
them to black & white. Even when the screen is black & white, onscreen
text and icons will still be displayed in color.
34
1 Open the [LCD/VF B&W] submenu.
[£ LCD/VF Setup] > [LCD/VF B&W]
2 Select [On] and then press the joystick.
NOTES
• If you set an assignable button to [LCD/VF B&W] (A 89), you can press the button to turn the black & white
display on and off.
• About the LCD and viewfinder screens: The screens are produced using extremely high-precision
manufacturing techniques, with more than 99.99% of the pixels operating to specification. Less than 0.01% of
the pixels may occasionally misfire or appear as black, red, blue or green dots. This has no effect on the
recorded image and does not constitute a malfunction.
5.5 mm
Using a Tripod
The camcorder is shipped with the TB-1 Tripod Base for tripods th 95 cm (3/8 in.)
screws. You can mount the camcorder on a tripod but do nse trips with mounting
screws longer than 5.5 mm (0.2 in.) as this may cause dathe cmcorder.
Using a Tripod with 0.64 cm (1/4 n.) Mo
Screws
To use a tripod with 0.64 cm (1/4 in.) mnting crews, first
attach the supplied tripod adapter base to tcamcorder and
then attach the tripod to the adapter base.
1 Remove the original TB-1 Tripod Base from the camcorder.
• Remove the 4 screws and then remove the base.
2 Attach the supplied tripod adapter base for 0.64 cm (1/4 in.)
tripods.
• Firmly screw in the 4 screws.
3 Attach the tripod.
• Firmly screw in the tripod screw.
Removing and Attaching the Grip Unit
The grip unit comes originally attached to the camcorder. You can remove it and replace it with the thumb rest
should the minimal configuration be necessary. Although you will not be able to use the joystick, you can set the
joystick's functions (up/down/left/right/SET) to assignable buttons (A 89) to be able to change settings that
require the joystick*. Also, the control dial (A 60, 61) and MAGN. button/Assignable button 7 (A 89) cannot
be used to operate the camcorder.
* Except during photo playback. Functions that require the joystick include all settings in the menus (A 27, 133), white balance,
Preparing the Camcorder
Removing the Grip Unit
1 Set the Q switch to OFF.
2 Unscrew the grip unit’s lock screw and gently detach the
grip unit.
35
• The grip unit contains an internal connection cable so
be sure not to pull it too forcefully.
3 Disconnect the grip unit’s connection plug.
4 Screw the thumb rest onto the camcorder.
Attaching the Grip Unit
The grip unit can be attached in any of 24 positions (at 15º
intervals) to give you a convenient grip angle for high- and
low-angle shooting.
1 Set the Q switch to OFF.
2 Unscrew the thumb rest and remove it from the
camcorder.
White line
3 Firmly insert the grip unit’s plug all the way into the grip
unit connection terminal on the camcorder.
• Make sure to insert the plug all the way in, uite
line around the terminal is not vise.
• If the plug is not correctly connectd (for example, if the
white line around the terminal is pary visie), all the
controls on the camcorder may be disabled.
4 Attach the grip unit to the camcorder aligning it at the
desired angle and tighten the grip unit’s lock screw.
Adjusting the Grip Belt
Adjust the grip belt so that you can reach the START/STOP button
on the grip unit with your index finger but still have a comfortable
but secure grip.
IMPORTANT
• Be careful not to drop the camcorder when adjusting the grip belt.
Preparing the Camcorder
Attaching a Shoulder Strap
Pass the ends through the strap mount and adjust the length of
the strap.
36
IMPORTANT
• Be careful not to drop the camcorder when attaching or adjusting
the shoulder strap.
Removing and Attaching the Terminal Covers
You can remove the plastic covers of the following terminals to access them more readily.
• AV OUT
• EXT
• REMOTE
• DC IN
• MIC
• USB and HDMI OUT
• × (headphones)
Removing the Terminal Covers
Open the terminal cover and gently pull isaigh
Attaching the Terminal Covers
Insert the connecting strip into the opening to attach the terminal cover.
NOTES
• If the connecting strip is difficult to grasp, use a pair of tweezers or similar
tool.
Preparing the Camcorder
The Camcorder’s Cooling System
[w Other Functions]
The camcorder’s internal temperature is controlled using a cooling fan that
will turn on whenever the camcorder itself is turned on. However, you can
turn off the cooling fan temporarily if necessary.
[Fan]
[On]
37
Operating modes:
1 Open the [Fan] submenu.
[w Other Functions] > [Fan]
2 Select [Automatic] and then press the joystick.
Options
[On]:
The cooling fan is on as long as the camcorder is on.
The cooling fan is temporarily turned off. If the camcorder's internal temperature rises too much,
[Automatic]:
will appear in yellow on the left of the screen. If the temperature starts to become critical, the
icon
will turn red and the cooling fan will come on to prevent overheating. Once the camcorder has
cooled off sufficiently, the fan will turn off again. While the fan is activated automatically,
appear next to the icon.
will
NOTES
• Depending on the ambient temperature and other shootonditis, the cooling fan may not turn off even if
you set [Fan] to [Automatic].
• The cooling fan cannot be turned off in
.
• When changing the camcorder’s configuratioful ot to obstruct the cooling fan’s air intake and
exhaust vents (marked respectively s AIR INEXHAUST VENT).
• If you set an assignable button to [Fn] (A 89), an press the button to toggle between the [On] and
[Automatic] settings.
Intake vent (AIR INTAKE)
Exhaust vent (EXHAUST VENT)
Using an SD Card
Using an SD Card
SD Cards Compatible for Use with the Camcorder
You can use the following types of commercially available Secure Digital (SD) cards with this camcorder. The
camcorder is equipped with two SD card slots. Initialize SD cards (A 40) when you use them with this
camcorder for the first time.
38
As of October 2012, the video recording function has been tested using SD/SDHC/SDXC cards made by
Panasonic, Toshiba and SanDisk.
Memory card type: . SD card, / SDHC card, 0 SDXC card
SD Speed Class*:
Capacity:
128 MB or larger**.
* When using an SD card without a speed class rating or one rated SD Speed Class 2, you may not be able to record video,
depending on the card used.
**SD cards with a capacity of 64 MB or smaller cannot be used to record video.
IMPORTANT
• After repeatedly recording, deleting and editing clips (fragmented memory), it will take longer to write data on
the SD card and recording may stop. Save your recordings and initialize the SD card using the camcorder.
NOTES
• About the Speed Class: Speed Class is a standard that indicas e minimum guaranteed data transfer
speed of SD cards. When you buy a new SD card, look fe SpeClass logo on the package.
We recommend using SD cards rated SD Speed Class 10.
SDXC Cards
You can use SDXC cards with this camorder. WhSDXC cards with other devices, such as digital
recorders, computers and card readersmake sure tht the external device is compatible with SDXC cards.
The table below summarizes compatibiliby computer operating system, as of October 2012. For the latest
information, however, contact the computererating system or card manufacturer.
Compatible operating systems for SDXC cards
Operating system
Windows 7
Compatibility
Compatible
Windows Vista
Windows XP
Mac OS X
Compatible (requires Service Pack 1 or later)
Compatible (requires Service Pack 3 and KB955704 update)
Compatible (requires version 10.6.5 or later)
IMPORTANT
• If you use an SDXC card with a computer OS that is not SDXC-compatible, you may be prompted to format
the card. In such case, cancel the operation to prevent data loss.
Using an SD Card
Inserting and Removing an SD Card
You can insert an SD card into SD card slot A or slot B. If you have two
SD cards, you can use both slots.
39
1 Turn off the camcorder.
2 Lift the LCD panel upwards and open the SD card compartment
cover.
3 Insert the SD card straight, with the label facing up, all the way
into the SD card slot until it clicks.
4 Close the SD card compartment cover.
• Do not force the cover closed if the SD card is not correctly inserted.
SD card access
indicator
Checking the Status of the SCard Slo
You can check the status of the SD carslots mmediately by looking at
the SD card 2/SD card 3 access indicator. Refer to the following table.
Depending on the position of the LCD panel, it may be difficult to see the
SD card access indicators. In such case, adjust the position or angle of
the LCD panel as necessary.
Access indicator color
Red
SD card slot status
Accessing the SD card.
Recording/playback is possible and the SD card slot is selected
for recording/playback.
Green
An SD card is not inserted, the SD card slot is not currently
selected, or the SD card is not being accessed.
Indicator off
IMPORTANT
• Observe the following precautions while either of the SD card access
indicators is illuminated in red. Failure to do so may result in permanent
data loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not open the SD card compartment cover and do not remove the SD cards.
• Turn off the camcorder before inserting or removing an SD card. Inserting or removing the SD card with the
camcorder on may result in permanent data loss.
• SD cards have front and back sides that are not interchangeable. Inserting an SD card facing the wrong
direction can cause a malfunction of the camcorder. Be sure to insert the SD card as described in step 3.
Using an SD Card
NOTES
• To remove the SD card: Push the SD card once to release it. When the SD card springs out, pull it all the way
out.
• If you set the [w Other Functions] > [Media Access LED] function to [Off], the access indicators will not
illuminate.
40
Initializing an SD Card
The first time you use an SD card with this camcorder, initialize it first. You can also initialize an SD card to
permanently delete all the data it contains.
When initializing an SD card, you can select quick initialization, which clears the file allocation table but does not
physically erase the stored data, or complete initialization, which deletes all data completely.
Operating modes:
1 Open the [Initialize Media] submenu.
[w Other Functions] > [Initialize Media]
[w Other Functions]
2 Select [*A] or [*B] and then press the joystick.
[Initialize Media]
3 Select [Complete] (complete initialization) or [Quick] ck
initialization) and then press the joystick.
4 Select [OK] and then press the joystick.
• If you are using the [Complete] initialization oss tjoystick twice to cancel the operation while it is
in progress. You can use the SD cd but all be erased.
5 When the confirmation message pears, press the joystick.
• The SD card is initialized and all the da it ontains is erased.
IMPORTANT
• Initializing an SD card will permanently erase all data, including custom picture files. Lost data cannot be
recovered. Make sure you save important recordings in advance.
• Depending on the SD card, the complete initialization may take up to a few minutes.
NOTES
• If you set an assignable button to [Initialize Media] (A 89), you can press the button to open the initialization
submenu.
Using an SD Card
Switching Between the SD Card Slots
The camcorder features two SD card slots, SD card slot A and SD card
slot B. If both slots contain an SD card, you can switch between them as
necessary.
41
Operating modes:
Press the SLOT SELECT button.
• The access indicator of the selected SD card slot will illuminate in green.
On the screen, the SD card selected is indicated with a Ð mark next to
the SD card icon.
NOTES
• You cannot use the SLOT SELECT button to switch between SD card
slots while recording.
• The SD card slot selected for recording will be used to record both clips
and photos.
Selecting the SD Card Recording Method
The camcorder features two useful SD card recording mrelay cording and double slot recording.
Relay recording: This allows you to continue recoon aer SD card if the SD card you are using becomes
full. Relay recording is available from SD card sD cd slot B, and vice versa.
Double slot recording: This records the same clip eously to both SD cards, which is a convenient way to
make a backup copy of your recordinwhile you r.
Operating modes:
To use relay recording
[w Other Functions]
By default, this function is activated. If it has been deactivated, follow the
procedure below to activate it.
[Relay Rec]
1 Open the [Relay Rec] submenu.
[w Other Functions] > [Relay Rec]
[On]
2 Select [On] and then press the joystick.
To use double slot recording
[w Other Functions]
[Double Slot Rec]
[Off]
1 Open the [Double Slot Rec] submenu.
[w Other Functions] > [Double Slot Rec]
2 Select [On] and then press the joystick.
NOTES
• During relay recording, there will be a very brief stop in the video at the
point where the recording switches to the other SD card. With the supplied software, Data Import Utility, you
• If an SD card becomes full during double slot recording, recording on both SD cards will stop. On the other
hand, if an error occurs with one of the SD cards, recording will continue on the other SD card.
• Double slot recording cannot be used with relay recording, pre-recording or deleting the last clip recorded.
Using an SD Card
Checking the Remaining Recording Time on the SD Card
When the camcorder is in
mode, the display on the upper left of the screen indicates which SD card slot
is in use and the available recording time (in minutes*) that remains on each SD card.
On the [Media] status screen (A 143), you can check the total space, SD speed class, used space, available
recording time and available number of photos on each of the SD cards.
42
Recovering Data on an SD Card
Some actions, such as suddenly turning off the camcorder or removing the SD card while data is being
recorded, can cause data errors on the SD card. In such case, you may be able to recover the data on the SD
card.
Operating modes:
1 Insert the SD card with the data to be recovered into the camcorder.
2 When the screen prompts you to recover the data, select [OK] and then press the joystick.
3 When the confirmation message appears, press the joystick.
NOTES
• In some cases, data may not be recovered, such as while systm is corrupted or the SD card is
physically damaged.
Adjusting the Black Balance
Adjusting the Black Balance
You can have the camcorder adjust the black balance automatically when ambient temperature changes
considerably or if there is a noticeable change in a true black video signal.
43
Operating modes:
1 Open the [ABB] screen.
[~ Camera Setup]
[~ Camera Setup] > [ABB]
[ABB]
2 Attach the body cap to the lens mount.
• If a lens was attached, remove the lens and replace the body cap.
3 Select [OK] and then press the joystick.
• The automatic black balance procedure will start.
4 When the confirmation message appears, press the joystick.
• If the body cap is not correctly attached, [Error] will appear on the screen. Press the joystick and repeat the
procedure from the beginning.
NOTES
• Adjusting the black balance may be necessary in the following cass:
- When using the camcorder for the very first time or after a lg priod of not using it.
- After sudden or extreme changes in ambient tempera
- After changing the ISO speed/gain settings.
• The automatic black balance procedure will taroxiely 40 seconds when the frame rate is set to PF24
or 24P.
• During the adjustment of the black blance, yotice some irregular displays appear on the screen. This
is not a malfunction.
• Resetting the camcorder’s settings ung the w Other Functions] > [Reset] > [All Settings] or [Camera
Settings] menu option will reset also the k balance adjustment. In such case, perform the procedure again.
Adjusting the Black Balance
44
Recording
3
45
Recording Video
This section explains the recording basics. Before you begin recording, make a test recording first to check if the
camcorder operates correctly. Record for approximately 15 minutes at the default bit rate, 24 Mbps (LPCM)
Operating modes:
Preparing to Record
1 Attach the handle unit, grip unit, etc. as necessary to build the desired
• Insert another SD card into the other SD card slot to ay recoing
5 Adjust the viewfinder.
Rear tally lamp
Recording
• The camcorder turns on in
mode.
mode and enters record pause
• At first, both SD card access indicators will illuminate in red. After a
moment, the access indicator of the SD card slot selected for
recording will turn green and the other access indicator will go out.
Access indicators
Recording Video
2 Press the START/STOP button to begin recording.
• Recording starts. The rear and front tally lamps illuminate and the
recording indicator [ÜREC] appears at the top of the screen.
• You can use the START/STOP button on the grip unit, the
camcorder's body (on the front, next to the lens mount) or the
handle unit.
46
3 Press the START/STOP button to pause the recording.
• The clip* is recorded to the SD card and the camcorder enters
record pause mode. Both tally lamps will go out.
Front tally
lamp
* “Clip” refers to one movie unit from the point you press the START/STOP button to
start recording until you press again to pause the recording.
IMPORTANT
• Observe the following precautions while either of the SD card access
indicators is illuminated in red. Failure to do so may result in
permanent data loss.
- Do not open the SD card compartment cover and do not remove
the SD cards.
- Do not disconnect the power source or turn off the camcorder.
• Be sure to save your recordings regularly (A 123), especially after aking important recordings. Canon shall
not be liable for any loss or corruption of data.
NOTES
• Depending on the shooting conditions, the camay pick up and record the operation sounds of the
lens (autofocus, aperture, image stabilization, cooing fan. In such case, using an external
microphone is recommended to rede the effe
• A single clip can be recorded continuusly for p to 12 hours. After 12 hours, the camcorder will automatically
stop recording.
• You can use [w Other Functions] > [Rec Review] (A 83) to review part or all of the last clip recorded.
• You can use [w Other Functions] > [Delete Last Clip] (A 140) to delete the last clip recorded. However, you
cannot delete the last clip if double slot recording is on.
• If [w Other Functions] > [HDMI] > [Rec Command] is set to [On] and you use the HDMI OUT terminal to
connect the camcorder to a device compatible with HDMI recording commands, when you start or stop
recording with the camcorder, the other device will also start or stop recording.
• When the camcorder switches form recording on one SD card to another during relay recording, the video will
be recorded as two separate relay clips. With the supplied software, Data Import Utility, you can join relay
• The video (stream) file in a clip will be split approximately every 2 GB for clips with a long recording time.
Even in such case, playback will be continuous. With the supplied software, Data Import Utility, you can join
Recording Video
Locking the Controls in Recording Mode
Once in
mode, you can set the Q switch to C (key lock) to
lock all the physical controls (buttons and switches) on the camcorder,
save for the START/STOP button*. This is useful in preventing settings
from being changed due to inadvertently pressing one of the buttons.
Return the Q switch to the CAMERA position to reactivate the
controls.
47
Additionally, the START/STOP button on the handle unit has its own lock
lever to prevent its accidental operation. Turn the lock lever to C position
to lock the START/STOP button**. Return the lock lever to its original
position to enable use of the START/STOP button again.
* With the [w Other Functions] > [Custom Function] > [C START/STOP] setting, you
can choose to lock all buttons, including the START/STOP button.
**You can still use the START/STOP buttons on the camcorder and grip unit.
Recording Video
Onscreen Displays
Refer to this section for an explanation of the various screen displays that appear in
mode. You can use
the custom display function (A 102) to turn off individual onscreen displays if they are not required.
48
1213
14
1516
17
18
19
20
21
22
1
2
3
4
5
6
23
7
24
8
9
25
26
10
11
27
28 29 30 3132 33 34 35
When displaying the date and time (A 26):
36
1
2
3
Remaining recording time for double lot
Current focal length of an attached EF lens*
High temperature warning and cooling fan
8 Onscreen displays recorded with the clip
19 Photo recording - available number of photos
4
5
6
7
8
9
16 Onscreen displays superimposed on video output
* The displayed value is an estimate.
**Only displayed when [w Other Functions] > [Bit Rate] is set to [24 Mbps LPCM].
NOTES
• You can press the DISP. button to switch the onscreen displays in the following sequence.
Show all onscreen displays → show only onscreen markers* → hide all onscreen displays.
* Only when [£ LCD/VF Setup] > [Markers] > [Enable] is set to [On].
Recording Video
1 Remaining battery time
• The icon shows a rough estimate of the remaining charge as a percentage of the full charge of the battery
pack. When a battery pack compatible with Intelligent System is used, the remaining recording/playback
time of the battery pack is displayed, in minutes, next to the icon.
49
• è ꢀ é ꢀ ê ꢀ ë ꢀ ì (in red).
When ì is displayed, replace the battery pack with a fully charged one.
• Depending on the conditions under which the camcorder and the battery pack are used, the actual
battery charge may not be indicated accurately.
2 SD card status/available recording time
• The following indicates the SD card status.
2/3 Can record on SD card
4/5 No SD card or cannot record on SD card
The SD card selected for recording is indicated with a Ð mark.
14 Recording operation
ÜREC
Recording
STBY
Record pause
ÜPRE REC
PRE REC STBY
Pre-recording (after pressing the START/STOP button)
Pre-recording (before pressing the STARTTOP button)
• When double slot recording (A 41) is activated, the con wippear to the left of the operation indicator.
Canon Log Gamma and CINEMA Preset
[~ Camera Setup]
You can easily set the camcorder to use nuber of preset picture-
related settings especially designed with professional cinematography
and motion picture production in mind. With the CINEMA preset settings,
[/ CINEMA Locked]
Log setting, which makes full use of the newly developed image sensor to
[Off]
offer spectacular dynamic range. On the other hand, other custom picture
settings will not be available.
Clips recorded using Canon Log gamma need to be processed in post-production. During post-production, you
can apply a LUT (look-up table) to clips recorded using Canon Log gamma to view the clips with more natural
colors. For details about available LUTs, visit your local Canon Web site.
1 Open the [/ CINEMA Locked] submenu.
[~ Camera Setup] > [/ CINEMA Locked]
2 Select [On] and then press the joystick.
• All picture-related settings will be set according to the CINEMA preset values.
• [/ LOCKED] appears on the left of the screen.
Recording Video
Checking Clips Recorded with Canon Log Gamma (View Assistance)
When Canon Log gamma is used, the image displayed on the screen will appear darker than usual. You can use
the view assistance function to display an image that approximates the one that would be obtained using a
normal gamma setting. View assistance is only applied on the camcorder screen; it will not affect your recordings
or the video signal output from the various terminals.
50
1 Open the [View Assist.] submenu.
[£ LCD/VF Setup]
[£ LCD/VF Setup] > [View Assist.]
2 Select [On] and then press the joystick.
will appear on the lower left of the screen.
[View Assist.]
[Off]
•
Video Configuration: System Frequency, Bit Rate and Frame Rate
Video Configuration: System Frequency, Bit Rate and Frame Rate
Before you record, select the bit rate and frame rate that best match your creative needs. The options available
will depend on the system frequency selected: 59.94 Hz (former NTSC broadcast area) or 50.00 Hz (former PAL
broadcast area). A single SD card can contain only one type of recordings.
51
Selecting the System Frequency
[w Other Functions]
Operating modes:
[System Frequency]
1 Open the [System Frequency] submenu.
[59.94 Hz] or [50.00 Hz]*
[w Other Functions] > [System Frequency]
2 Select [59.94 Hz] or [50.00 Hz] and then press the joystick.
• The camcorder will reset and restart in the selected mode.
* Depending on the country/region
of purchase.
Selecting the Bit Rate
[w Other Functions]
[Bit Rate]
The bit rate selected determines also the resolution (frame size) and audio
recording mode of the recordings.
Operating modes:
[24 Mbps LPCM]
1 Open the [Bit Rate] submenu to set the bit rate and res.
[w Other Functions] > [Bit Rate]
2 Select the desired option and then press the
• The selected bit rate will appear the uppethe screen.
Selecting the Frame Rate
[w Other Functions]
[Frame Rate]
Operating modes:
1 Open the [Frame Rate] submenu to set the frame rate.
[w Other Functions] > [Frame Rate]
[60i] or [50i]*
2 Select the desired option and then press the joystick.
• The selected frame rate will appear on the upper right of the screen.
* Depending on the country/region
of purchase.
NOTES
• A single SD card cannot be used to record clips at different system frequencies (50.00 Hz recordings/59.94 Hz
recordings).
• Clips recorded using the 24P frame rate cannot be converted to standard definition using the camcorder.
Video Configuration: System Frequency, Bit Rate and Frame Rate
Available bit rate and frame rate settings
[System Frequency]
set to [59.94 Hz]
[System Frequency]
set to [50.00 Hz]
[Bit Rate]
setting
Resolution
Audio recording mode
Linear PCM, 2ch
1
52
Available [Frame Rate] settings
[24 Mbps LPCM]
[24 Mbps]
[60i]
[PF30]
[PF24]
[24P]
[50i]
2
3
1920 x 1080
1440 x 1080
4
[PF25]
[17 Mbps]
Dolby Digital, 2ch
[7 Mbps]
1
2
3
4
The camcorder uses a variable bit rate (VBR).
Shooting at 30 frames per second, progressive; recorded as 60i.
Shooting at 24 frames per second, progressive; recorded as 60i.
Shooting at 25 frames per second, progressive; recorded as 50i.
Changing Main Camera Functions with the Joystick
Changing Main Camera Functions with the Joystick
You can adjust three main camera functions –shutter speed, white balance and ISO speed/gain– using only the
joystick. This section will explain the basic operation for changing a value. For specific details about the functions
please refer to the each function’s section: shutter speed (A 54), white balance (A 63), ISO speed/gain
53
Operating modes:
1 Press the joystick.
White balance (highlighted in orange)
• The white balance mode icon will be highlighted in orange. If no
operation is performed for more than 6 seconds, the display will
return to normal.
• Push the joystick left/right to move the highlight between the
white balance mode icon, the ISO/gain value and the shutter
value.
2 Push the joystick up/down to select the desired value (ISO
speed, gain, shutter) or desired white balance mode and then
press the joystick.
Push the joystick (ÏÐ) to highlight the ISO/
Gain value or the Shutter value
• The selected value will be set and the display will return to
normal.
Shutter Speed
Shutter Speed
Set the shutter speed based on the recording conditions. For example, you may want to set slower shutter
speeds in darker environments. The camcorder offers the following 5 modes.
54
Operating modes:
[Speed]: Allows you to set the shutter speed (in fractions of a second). You can select the increment to use when
adjusting the shutter speed between 1/3-stop and 1/4-stop increments.
[Angle]: You can set the shutter angle to determine the shutter speed.
[Clear Scan]: Set the frequency in order to record CRT computer monitors without displaying black bands or
flicker on the screen.
[Slow]: You can set slower shutter speeds to obtain brighter recordings in places with insufficient lighting.
[Off]: The camcorder uses a standard shutter speed based on the frame rate.
Available Shutter Speeds
The available shutter speeds vary depending on the fram
e rat59.94 Hz recordings)
Shutter mode
60i
PF30
PF24 / 24P
Off
1/60
1/60, 1/80, 1/100, 1/125/160, 1/200, 1/40, 1/50, 1/60, 1/80, 1/100, 1/25, 1/30, 1/40, 1/50, 1/60, 1/80,
increments 1/250, 1/320, 1/400, 1/501/640, 1/125, 1/160, 1/200, 1/250, 1/320, 1/100, 1/125, 1/160, 1/200, 1/250,
1/800, 1/1000, 1/1250, 1/1601/00 1/400, 1/500, 1/640, 1/800, 1/1000, 1/320, 1/400, 1/500, 1/640, 1/800,
1/1250, 1/1600, 1/2000 1/1000, 1/1250, 1/1600, 1/2000
1/60, 1/75, 1/90, 1/100, 1/120, 1/150, 1/30, 1/34, 1/40, 1/48, 1/60, 1/75, 1/90, 1/24, 1/30, 1/34, 1/40, 1/48, 1/60, 1/75,
1/24
Speed
1/3-stop
1/4-stop
increments 1/180, 1/210, 1/250, 1/300, 1/360,
1/420, 1/500, 1/600, 1/720, 1/840,
1/1000, 1/1200, 1/1400, 1/1700,
1/2000
1/100, 1/120, 1/150, 1/180, 1/210, 1/250, 1/90, 1/100, 1/120, 1/150, 1/180, 1/210,
1/300, 1/360, 1/420, 1/500, 1/600, 1/720, 1/250, 1/300, 1/360, 1/420, 1/500, 1/600,
1/840, 1/1000, 1/1200, 1/1400, 1/1700, 1/720,1/840, 1/1000, 1/1200, 1/1400,
1/2000
1/1700, 1/2000
Angle
360°, 240°, 216°, 180°, 120°, 90°, 360°, 240°, 216°, 180°, 120°, 108°, 360°, 345.6°, 288°, 240°, 180°,
60°, 45°, 30°, 22.5°, 15°, 11.25°
90°, 60°, 45°, 30°, 22.5°, 15°,
11.25°
172.8°, 144°, 120°, 90°, 86.4°, 72°,
60°, 45°, 30°, 22.5°, 15°, 11.25°
23.98 Hz to 250.27 Hz
Clear Scan
Slow
59.94 Hz to 250.27 Hz
1/4, 1/8, 1/15, 1/30
29.97Hz to 250.27 Hz
1/4, 1/8, 1/15
1/3, 1/6, 1/12
Frame rate (50.00 Hz recordings)
1/25
Shutter mode
50i
PF25
Off
1/50
Speed
1/3-stop
1/50, 1/60, 1/80, 1/100, 1/125, 1/160, 1/200, 1/250, 1/320, 1/25, 1/30, 1/40, 1/50, 1/60, 1/80, 1/100, 1/125, 1/160,
increments 1/400, 1/500, 1/640, 1/800, 1/1000, 1/1250, 1/1600,
1/2000
1/200, 1/250, 1/320, 1/400, 1/500, 1/640, 1/800, 1/1000,
1/1250, 1/1600, 1/2000
1/4-stop
1/50, 1/60, 1/75, 1/90, 1/100, 1/120, 1/150, 1/180, 1/210,
1/25, 1/29, 1/33, 1/40, 1/50, 1/60, 1/75, 1/90, 1/100, 1/120,
1/150, 1/180, 1/210, 1/250, 1/300, 1/350, 1/400, 1/500, 1/600,
1/700, 1/800, 1/1000, 1/1200, 1/1400, 1/1600, 1/2000
increments 1/250, 1/300, 1/350, 1/400, 1/500, 1/600, 1/700, 1/800,
1/1000, 1/1200, 1/1400, 1/1600, 1/2000
Angle
360°, 300°, 240°, 180°, 150°, 120°, 90°, 60°, 45°, 30°, 360°, 300°, 240°, 180°, 150°, 120°, 90°, 75°, 60°, 45°,
22.5°, 15°, 11.25°
50.00 Hz to 250.78 Hz
1/3, 1/6, 1/12, 1/25
30°, 22.5°, 15°, 11.25°
25.00 Hz to 250.78 Hz
1/3, 1/6, 1/12
Clear Scan
Slow
Shutter Speed
Changing the Shutter Mode
[~ Camera Setup]
1 Open the shutter [Mode] submenu.
[~ Camera Setup] > [Shutter] > [Mode]
[Shutter]
[Mode]
55
2 Select the desired mode and then press the joystick.
• If you selected [Speed] (the default value), you can continue the
procedure to select the increment scale to use when adjusting the
shutter speed.
[Speed]
3 Open the [Shutter Increment] submenu.
[~ Camera Setup] > [Shutter] > [Shutter Increment]
[~ Camera Setup]
[Shutter]
4 Select [1/3 stop] or [1/4 stop] and then press the joystick.
[Shutter Increment]
[1/4 stop]
Adjusting the Shutter Value
1 Press the SHUTTER button.
• The current shutter value will be highlighted nge.
2 Push the joystick up/down to select the uttvalue
(shutter speed, angle value or clar scan fy) and then
press the joystick.
• The selected shutter value will be sand e display will return to
normal.
NOTES
• If you set an assignable button to [SHUTTER] (A 89), you can press that button instead of the SHUTTER
button to highlight the shutter value.
Using Slow Shutter Mode
When recording in dark surroundings, you can obtain a brighter picture by using slow shutter mode. You can
also use this mode when you wish to add certain effects to your recordings, such as blurring the background
during panning shots or recording a moving subject with an afterimage trail.
• Image quality may not be as good as when using faster shutter speeds in brighter surroundings.
Shutter Speed
NOTES
• Closing down the aperture when recording under bright conditions may cause the picture to appear soft or out
of focus. To avoid the loss of sharpness due to diffraction, use a faster shutter speed, a denser ND filter
56
• When the shutter mode is set to [Slow], bright red, green or blue dots may appear on the screen. In such case,
• Even when using the [C7: EOS Std.] preset custom picture file, if you set the camcorder to a certain shutter
speed, you may not get the exactly the same image brightness as you would on an EOS digital SLR camera
set to the same shutter speed.
• When an optional RC-V100 Remote Controller is connected to the camcorder, you can change the shutter
mode with the remote controller's SHUTTER SELECT button.
Flicker Reduction
[~ Camera Setup]
You can perform the following procedure to have the camcorder
automatically detect and reduce flicker.
[Flicker Reduction]
1 Open the [Flicker Reduction] submenu.
[Off]
[~ Camera Setup] > [Flicker Reduction]
2 Select [Automatic] and then press the joystick.
NOTES
• When recording under artificial light sors surescent, mercury or halogen lamps, the screen may
flicker depending on the shutter sped. You may e to avoid flicker by setting the shutter mode to
[Speed] and the shutter speed to a ve matching the frequency of the local electrical system: 1/50* or 1/100
for 50 Hz systems, 1/60 or 1/120 for 6Hz sstems.
* May not be available depending on the frame rate.
ISO Speed/Gain
ISO Speed/Gain
Depending on the shooting conditions you may want to adjust the brightness of the image. You can do so by
changing the ISO speed or gain value to adjust the sensitivity of the sensor.
57
Operating modes:
Available ISO speed and gain settings
1
Increment
Normal range
Extended range
2
3
2, 4
2
1-stop increments
320 , 400, 800, <850> , 1600, 3200, 6400, 12800, 20000
25600, 51200, 80000
3
320, 400, 500, 640, 800, <850> , 1000, 1250, 1600, 2000,
2500, 3200, 4000, 5000, 6400, 8000, 10000, 12800, 16000,
20000
ISO Speed
Gain
25600, 32000, 40000, 51200,
64000, 80000
1/3-stop increments
-6 dB, -3 dB, 0 dB, 3 dB, 6 dB, 9 dB, 12 dB, 15 dB, 18 dB,
21 dB, 24 dB, 27 dB, 30 dB
Normal
Fine
33 dB, 36 dB, 39 dB, 42 dB
–
0 dB to 24 dB in 0.5 dB increments
1
2
3
4
Settings available only when [~ Camera Setup] > [ISO/Gain] > [Extended Range] is set to [On].
The minimum and maximum ISO speeds are available even when the 1-stop increment scale is selected.
ISO speed required for a suitable dynamic range for Canon Log gamma. Equivalent to a gain value of 2.5 dB.
This value is only available when [Extended Range] is set to [Off].
Changing the ISO Speed or Gain Setts
[~ Camera Setup]
[ISO/Gain]
[Select]
1 Open the ISO Speed/Gain [Select] subm
[~ Camera Setup] > [ISO/Gain] > [Select]
2 Select [ISO] or [Gain] and then pss the joystick.
If you selected [ISO] (the default value):
3 Open the [ISO Increment] submenu to select the increment to
use when adjusting the ISO speed.
[ISO]
[~ Camera Setup] > [ISO/Gain] > [ISO Increment]
4 Select [1 stop] or [1/3 stop] and then press the joystick.
[~ Camera Setup]
[ISO/Gain]
If you selected [Gain]:
3 Open the [Gain] submenu to select the increment to use when
adjusting the gain.
[~ Camera Setup] > [ISO/Gain] > [Gain]
[ISO Increment]
[1/3 stop]
4 Select [Normal] (3-dB increment) or [Fine] (0.5-dB increment) and
then press the joystick.
[~ Camera Setup]
[ISO/Gain]
[Gain]
[Normal]
ISO Speed/Gain
Adjusting the ISO/Gain Value
1 Press the ISO/GAIN button.
• The current ISO/gain value will be highlighted in orange.
58
2 Push the joystick up/down to select the desired ISO speed or
gain value and then press the joystick.
• The selected ISO/gain value will be set and the display will return to
normal.
• You can also adjust the ISO/gain value using only the joystick
NOTES
• When high ISO speeds or gain levels are set, the picture may flicker slightly.
• When high ISO speeds or gain levels are set, bright red, green or blue dots may appear on the screen. In such
• When the ISO speed or gain level is changed, some noise may appar momentarily on the screen. Do not
adjust the ISO speed/gain level while recording.
• When an optional RC-V100 Remote Controller is connethe cmcorder, you can adjust the ISO speed
or gain value with the remote controller's ISO/GAIN Í/ons.
ND Filter
ND Filter
Using the ND filters allows you keep the aperture within an appropriate
range when recording in bright surroundings*.
* Closing down the aperture when recording under bright conditions may cause the
picture to appear soft or out of focus. To avoid the loss of sharpness due to diffraction,
59
Operating modes:
Turn the ND FILTER dial toward the + or - direction to select the
desired ND filter setting.
• Turning the dial up (in the + direction) will change the ND filter setting in
the following order: [ND1 2 stops] ꢀ [ND2 4 stops] ꢀ [ND3 6 stops] ꢀ
ND filter off. (Turning the dial down (in the - direction) will cycle through
the settings in reverse order.)
NOTES
• Depending on the scene, the color may change when turning he D filter on/off. Setting a custom white
Adjusting the Aperture
Adjusting the Aperture
You can affect the brightness of your recordings or change the depth of field by adjusting the aperture. For
example, use a small aperture value for a shallow depth of field that isolates the subject in focus and nicely blurs
the background. You can have the camcorder automatically set the aperture according to the brightness of the
subject, or adjust the aperture manually.
60
Operating modes:
Automatic Aperture
When an EF-S 18-135mm f/3.5-5.6 IS STM or EF-S 18-55mm f/3.5-5.6 IS STM lens is attached to the
camcorder, you can have the camcorder automatically adjust the aperture (f/stop).
1 Open the aperture [Mode] submenu.
[~ Camera Setup] > [Iris] > [Mode]
[~ Camera Setup]
2 Select [Automatic] and then press the joystick.
[Iris]
• When the camcorder is set to automatic aperture, m will appear on
the screen next to the aperture value.
[Mode]
[Manual]
NOTES
button to toggle between the [Automatic] and ] segs.
Manual Aperture Control
You can adjust the aperture value of most EF lenses using the control
dial on the grip unit. Available aperture values will vary depending on
the EF lens attached to the camcorder.
By default, the camcorder is set to manual aperture. If the aperture
mode was changed, set [~ Camera Setup] > [Iris] > [Mode] to
Control dial
Selecting the Increment Scale to Use When Adjusting the
Aperture
[~ Camera Setup]
[Iris]
1 Open the [Iris Increment] submenu.
[~ Camera Setup] > [Iris] > [Iris Increment]
2 Select [1/2 stop], [1/3 stop] or [Fine] and then press the joystick.
[Iris Increment]
[1/3 stop]
Changing the Aperture Value
Turn the control dial to adjust the aperture.
• The selected aperture value will appear on the lower left of the screen.
• When [~ Camera Setup] > [Iris] > [Iris Increment] is set to [Fine], the actual increments will be smaller than
1/3 stop but the onscreen display will show the closest 1/3-stop aperture value.
Adjusting the Aperture
NOTES
• When using an EF lens with no lens contacts, such as a Canon Cinema lens, you cannot adjust the aperture
using the camcorder. Adjust the aperture using the lens.
• You can use the [w Other Functions] > [Custom Function] > [Grip Ctrl Dial Dir.] setting (A 102) to change
the direction of the adjustment when you turn the control dial.
61
• If you are using an EF lens that can correct the aperture value according to the position of the zoom, you can
use the [~ Camera Setup] > [Iris] > [Zoom-Iris Correct.] setting to select whether to maintain the f/stop as
you zoom.
• If you set an assignable button to [Iris +] or [Iris -] (A 89), you can press the button to respectively open up or
close the aperture.
• When an optional RC-V100 Remote Controller is connected to the camcorder, you can adjust the aperture
with the remote controller's IRIS dial. At default settings, turn the dial right to open up the aperture (smaller F
value) and left to close the aperture (larger F value).
Momentary Automatic Aperture - Push Auto Iris
During manual aperture, you can press the PUSH AUTO IRIS button to have
the camcorder temporarily take control and automatically adjust the aperture
(f/stop) for an optimal exposure.
Hold down the PUSH AUTO IRIS button.
• The camcorder will automatically adjust the aperture toptim
exposure. As long as you hold the button pressed dowill appear on
the screen next to the aperture value.
• When you release the button, the selected f/set as the aperture
value. Automatic aperture mode wiend and thnext to the aperture
value will disappear.
Exposure Compensation - AE Shift
Use AE shift to compensate the exposure that was set using automatic
aperture, in order to darken or lighten the image. You can select from 15
available AE shift levels.
1 Open the [AE Shift] submenu.
[~ Camera Setup] > [AE Shift]
[~ Camera Setup]
2 Select an AE shift level and then press the joystick.
[AE Shift]
[ 0]
Available AE Shift Levels
+2.0 +1.5 +1.25 +1.0 +0.75 +0.5 +0.25
0
-0.25 -0.5 -0.75 -1.0 -1.25 -1.5
-2.0
NOTES
• You can also set the AE shift level by turning the control dial while holding the PUSH AUTO IRIS button
pressed down.
• If you set an assignable button to [AE Shift +] or [AE Shift -] (A 89), you can press the button to adjust the AE
shift level.
• When you use automatic aperture (including push auto iris) after setting an AE shift level, the camcorder will try
to adjust the aperture (f/stop) so as to achieve the AE shift level that was set rather than optimal aperture.
Adjusting the Aperture
The Exposure Bar
You can use the exposure bar as a reference when adjusting the aperture or
shutter speed or when compensating the exposure using AE shift. The Î on
top of the exposure bar indicates optimal exposure without any shift (AE 0); the
scale markings indicate the deviation from optimal exposure in 1/2 EV
increments. The indicator inside the exposure bar represents the current
exposure. When the difference between current and optimal exposure is larger
than 2 EV, the indicator will flash at the edge of the exposure bar. Optimal
Optimal exposure AE 0
Current exposure
62
Light Metering Mode
Select the light metering mode to match the recording conditions. Using the appropriate setting will ensure that
the camcorder obtains the most suitable exposure level when automatic aperture is used.
1 Open the [Light Metering] submenu.
[~ Camera Setup] > [Light Metering]
[~ Camera Setup]
[Light Metering]
[Standard]
2 Select the desired option and then press the joystick.
• The icon of the selected mode appears on the left of treen.
Options
[Backlight] °:
[Standard]:
Suitable when recording backlit
Averages the light metered from cre, giving more weight to the subject in the center.
Use this option when cording a which only a certain part of the picture is lit, for example,
when the subject is lit a spotlight.
[Spotlight] ®:
NOTES
• If you set an assignable button to [Backlight] or [Spotlight] (A 89), you can press the button to change the
light metering mode.
White Balance
White Balance
The camcorder uses an electronic white balance process to calibrate the picture and ensure accurate colors
under different lighting conditions. There are 4 methods of setting the white balance.
63
Custom white balance: You can use a white object to establish the white balance and set it to one of two custom
white balance positions, ÅA or ÅB.
Preset white balance: Set the white balance to ¼ (daylight) or
(incandescent lamp). Preset white balance
settings can be further fine-tuned within a range of -9 to 9.
Set color temperature: Allows you to set the color temperature between 2,000 K and 15,000 K.
Auto white balance: The camcorder automatically adjusts the white balance to the optimal level.
Operating modes:
NOTES
• The [Color Matrix] (A 99) and [White Balance] (A 99, 101) custom picture settings take precedence over the
white balance settings.
• You can use the [w Other Functions] > [Custom Function] > [Shockless WB] setting (A 102) to make the
transition look smoother when you change the white balance settings.
• When an optional RC-V100 Remote Controller is connected tthe amcorder, you can adjust the white
balance with the remote controller's A button, B button, PRESET ton and Å button.
Custom White Balance
1 Press the WB button.
• The white balance mode icon will bhighlhted in orange.
• You can also select the white balance mode icon using only the
2 Push the joystick up/down to select the ÅA or ÅB icon.
• If a custom white balance has been stored previously, press the
joystick to set the stored custom white balance. You do not need to
perform the rest of the procedure.
• If a custom white balance has not yet been stored, the custom white
balance icon ÅA or ÅB and default value (5,500 K) will flash slowly.
Continue the procedure to establish the custom white balance.
3 Point the camcorder at a white object so that it fills the whole
screen.
• Use the same lighting conditions you plan to use when recording.
4 Press the Å button.
• The Å A or Å B icon will flash quickly.
• Make sure the white object fills the screen until the procedure is completed.
• After the icon stops flashing, the procedure is completed. The setting is retained even if you turn off the
camcorder.
NOTES
• Readjust the custom white balance if the light source or ND filter setting changes.
• Very rarely and depending on the light source, Å may keep flashing (it will change to a slow flashing). The
result will still be better than with the auto white balance.
White Balance
Preset White Balance Settings
1 Press the WB button.
• The white balance mode icon will be highlighted in orange.
64
2 Push the joystick up/down to select the ¼ or É icon and then press the joystick.
• If necessary, instead of pressing the joystick, you can continue the procedure to fine-tune the preset settings
within a range of -9 to 9.
3 Press the Å button.
• The adjustment value 0 will appear next to the white balance icon, highlighted in orange.
4 Push the joystick up/down to change the adjustment value and then press the joystick.
• The selected adjustment value will be set and will appear next to the white balance icon.
Color Temperature Setting
1 Press the WB button.
• The white balance mode icon will be highlighted in orange.
2 Push the joystick up/down to select the È icon.
3 Press the Å button.
• The default color temperature value (5,500 Ke higghted in orange.
4 Push the joystick up/down to change the perure value and then press the joystick.
• The selected color temperature wibe set and ear next to the white balance icon.
Auto White Balance
The camcorder constantly adjusts the white balance automatically to achieve an optimal level. The camcorder
will adjust the white balance if the light source changes.
1 Press the WB button.
• The white balance mode icon will be highlighted in orange.
2 Push the joystick up/down to select the m icon and then press the joystick.
• The m icon appears next to the color temperature display.
NOTES
• Custom white balance may provide better results in the following cases:
- Changing lighting conditions
- Close-ups
- Subjects in a single color (sky, sea or forest)
- Under mercury lamps and certain types of fluorescent and LED lights
Adjusting the Focus
Adjusting the Focus
The camcorder offers three ways to focus.
Manual focus: Turn the focus ring on the attached lens to adjust the focus. The camcorder offers several focus
assistance functions to help you focus more accurately when using the manual focus.
65
One-shot AF: With the lens's focus mode switch set to AF, press and hold the ONE-SHOT AF button to let the
camcorder focus automatically on the subject at the center of the screen.
Continuous AF*: Set the lens's focus mode switch to AF to have the camcorder continuously focus on the
subject.
* Only when an EF-S 18-135mm f/3.5-5.6 IS STM or EF-S 18-55mm f/3.5-5.6 IS STM lens is attached to the camcorder.
Operating modes:
Manual Focus
Turn the focus ring to adjust the focus.
NOTES
• In most cases, you can use the focus ring on the lens to aust thcus even when the focus mode switch is
set to AF (autofocus). However, depending on the lencus rinmay be disabled in AF mode. In such
case, set the focus mode switch to MF.
• If you operate the zoom after focusing manucus n the subject may be lost.
• When adjusting the focus, be careful oto toont of the lens or moving parts on the lens except for
the focus ring.
• If you focus manually and then leave he camorder with the power turned on, the focus on the subject may
be lost after a while. This possible slighshifin focus is a result of the internal temperature rising in the
camcorder and lens. Check the focus before resuming shooting.
• When an optional RC-V100 Remote Controller is connected to the camcorder, you can adjust the focus with
the remote controller's FOCUS dial. At default settings, turn the dial right to focus farther and left to focus
nearer.
One-Shot AF
1 Set the focus mode switch on the lens to AF in advance.
• Refer to the instruction manual of the lens used.
• [AF] will appear on the left of the screen.
2 Press and hold the ONE-SHOT AF button.
• The AF frame will appear at the center of the screen and the
camcorder will focus automatically. When correct focus has been
achieved, the AF frame turns green.
• If the camcorder cannot focus automatically, the AF frame will turn
red.
• The AF frame will disappear when you release the ONE-SHOT AF
button.
Adjusting the Focus
Continuous AF
When a compatible lens is attached to the camcorder, you can have the camcorder focus automatically.
1 Set the focus mode switch on the lens to AF in advance.
• Refer to the instruction manual of the lens used.
• [AF] will appear on the left of the screen.
[~ Camera Setup]
[AF Mode]
66
2 Open the [AF Mode] submenu.
[~ Camera Setup] > [AF Mode]
[One Shot]
3 Select [Continu.] and then press the joystick.
NOTES
• One-shot AF is not available when the shutter mode is set to [Slow] and the shutter speed is set to 1/4 or 1/3.
• When the frame rate is set to PF30, PF24 or 24P (59.94 Hz recordings) or PF25 (50.00 Hz recordings), the
camcorder will take longer to focus automatically.
• When [~ Camera Setup] > [AF Mode] is set to [Continu.], the ONE-SHOT AF button will be disabled. To use the
button, set it to [One Shot].
• The point where the camcorder focuses may change slightly depending on shooting conditions, such as subject,
brightness and zoom position. Check the focus before resuming shoog.
• Autofocus (one-shot or continuous) is only available when usinEF nses equipped with autofocus (AF)
function. Refer to the instruction manual of the lens used.
• With some EF lenses, the camcorder may take longer tautomcally or may not be able to focus
correctly. Visit your local Canon Web site for the t infation.
• Autofocus may not work well on the following or in he following cases. In such case, focus manually.
- Reflective surfaces
- Subjects with low contrast or withut vertical lin
- Fast moving subjects
- Through dirty or wet windows
- Night scenes
Adjusting the Focus
Using the Focus Assistance Functions
In order to focus more accurately, you can use two focus assistance functions – peaking, which creates a clearer
contrast by emphasizing the outlines of the subject, and magnification, which enlarges the image on the screen.
You can use both functions simultaneously for greater effect.
You can also use the [w Other Functions] > [Custom Function] > [F. Assist. B&W] setting (A 102) to switch
the screen to black & white while using the focus assistance functions.
67
Peaking
[£ LCD/VF Setup]
The camcorder offers two peaking levels. Select the level before activating
peaking.
[Select]
(under [Peaking])
1 Press the PEAKING button.
• The peaking icon (J or K) appears at the lower center of the
screen and the outlines in the image will be emphasized, depending
on the focus.
[Peaking 1]
• Press the button again to turn off peaking.
• Alternatively, you can use the [£ LCD/VF Setup] > [Peaking]
setting to turn peaking on and off.
2 Open the [Select] submenu (under [Peaking]) to select the peaking level.
[£ LCD/VF Setup] > [Select] (under [Peaking])
3 Select the desired level and then press the joystick.
Magnification
1 Press the MAGN. button.
• ^ appears at the lower center ote sche center of the
screen is magnified approximatel2 times*.
2 If necessary, use the joystick (ÝÞ) to mve around the orange
frame and check other parts of the ime.
• Set the focus mode switch on the lens to MF in advance.
• You can move the orange frame 5 steps vertically or horizontally.
Press the CANCEL button to return the magnification frame to the
center position.
3 Press the MAGN. button again to cancel the magnification.
* The magnification that appears on the LCD screen and on the viewfinder screen is
different. The magnification also differs based on the video configuration.
NOTES
• Peaking/Magnification appears only on the camcorder screen. It will not appear on an external monitor
connected to the camcorder and will not affect your recordings.
• You can use the [£ LCD/VF Setup] > [Peaking 1] and [Peaking 2] settings to set the color, gain and
frequency of the two peaking levels independently of each other.
• The camcorder features professional video scopes (A 81). You can display the edge monitor to help you
focus even more accurately.
• You can use peaking together with the edge monitor. In such case, The gain and frequency of the peaking
effect will be adjusted automatically according to the gain settings of the edge monitor.
• You can use the [w Other Functions] > [Custom Function] > [Magn. Add. Disp.] setting (A 102) to select
an additional assistance display (peaking or the edge monitor) to also be displayed when magnification is
used.
Onscreen Markers and Zebra Patterns
Onscreen Markers and Zebra Patterns
Using onscreen markers allows you to make sure your subject is correctly framed and is within the appropriate
safe area. The zebra patterns help you identify areas that are overexposed. The onscreen markers and zebra
pattern will not affect your recordings.
68
Operating modes:
Displaying Onscreen Markers
[£ LCD/VF Setup]
The camcorder offers 5 types of onscreen markers. You can display
multiple onscreen markers simultaneously.
[Markers]
1 Open the [Markers] submenu.
[£ LCD/VF Setup] > [Markers]
[Center]
[Horizontal]
[Grid]
[Safety Zone]
[Aspect Marker]
2 Select a marker you wish to display, select [White] or [Gray] and
then press the joystick.
• Select [Off] to turn off the selected marker.
• You can display multiple markers simultaneously. Repeat this step s
necessary.
[Off]
• If you selected [Safety Zone] or [Aspect Marker], constep 3
Otherwise, you can skip to step 4.
3 Select [Safety Zone Area] or [Aspect Ratiothe esired option and then press the joystick.
4 Select [Enable], select [On] and thn press ick to enable the onscreen markers.
• All of the selected onscreen markewill be displayed.
• Select [Off] to turn off all onscreen mrkers
Options
[Center]:
Displays a small marker that indicates the center of the screen.
[Horizontal]:
[Grid]:
Displays a horizontal line to help you compose level shots.
Displays a grid that allows you to frame your shots correctly (horizontally and vertically).
Displays indicators that show various safe areas, such as the action safe area and text safe area.
Available options for [Safety Zone Area] are [80%], [90%], [92.5%] and [95%].
[Safety Zone]:
[Aspect Marker]: Displays markers that indicate various aspect ratios to help you keep your shot within that area.
Available options for [Aspect Ratio] are [4:3], [13:9], [14:9], [1.66:1], [1.75:1], [1.85:1] and [2.35:1].
Safety zone 80%
Level marker
Aspect guide 4:3
Onscreen Markers and Zebra Patterns
Grid
Center marker
69
NOTES
• If you set an assignable button to [Markers] (A 89), you can press the button to turn the onscreen markers on
and off.
Displaying Zebra Patterns
[£ LCD/VF Setup]
The camcorder has a zebra pattern feature that shows black and white
diagonal stripes over areas that are overexposed. This is displayed oy
on the screen and will not affect your recordings. There are two tpeof
zebra patterns and you can display both simultaneously. Z1 lets ou
[Select]
(under [Zebra])
identify areas within a certain range ( 5% of a specified lile zeb
[Zebra 1]
2 lets you identify areas that are over a specified l. Whu display
both simultaneously and they overlap, only zebe dplayed in
those areas.
1 Open the zebra pattern [Select] bmenu.
[£ LCD/VF Setup] > [Select] (unde[Zeb])
2 Select [Zebra 1], [Zebra 2] or [Zebra 1&2] and then press the
joystick.
3 Open the zebra level submenu.
[£ LCD/VF Setup] > [Zebra 1 Level] or [Zebra 2 Level]
4 Select a zebra level and then press the joystick.
5 Press the ZEBRA button to activate the selected zebra pattern.
• Alternatively, before closing the menu, you can also select [Zebra],
select [On] and then press the joystick.
NOTES
• You can use the [£ LCD/VF Setup] > [Zebra HD Output] setting to display the zebra pattern on an external
monitor connected to the HDMI OUT terminal (HD output only).
Setting the Time Code
Setting the Time Code
The camcorder generates a time code signal and embeds it in your recordings. You can output the time code
along with video output from the HDMI OUT terminal (A 140). For 59.94 Hz recordings, you can also select
between a drop frame and non-drop frame time code.
70
Operating modes:
Selecting the Running Mode
[¤ TC/UB Setup]
You can select the running mode of the camcorder’s time code.
[Time Code]
1 Open the time code [Mode] submenu.
[¤ TC/UB Setup] > [Time Code] > [Mode]
[Mode]
2 Select the desired option and then press the joystick.
• If you selected [Regen.], you do not need to perform the rest of this
procedure. If you selected [Preset] and would like to set the time
[Preset]
code’s initial value, see the following section Setting the Time Code’s
Initial Value.
[¤ TC/UB Setup]
3 After you select [Preset], open the time code [Run] smenu.
[¤ TC/UB Setup] > [Time Code] > [Run]
[Time Code]
4 Select the desired option and then press ttick
[Run]
Options
[Preset]: The time code starts from an tial value yelect in
advance. The default initial timcode is 00:00:00.00. The time
code’s running mode depends othe [un] setting.
[Rec Run]: The time code runs only while recording so clips
recorded consecutively on the same SD card will have
continuous time codes.
[Rec Run]
[Free Run]: The time code starts running the moment you press
the joystick to select this option and keeps running
regardless of the camcorder’s operation.
[Regen.]: The camcorder will read the selected SD card and the time code
will continue from the last recorded time code on the SD card.
The time code runs only while recording so clips recorded
consecutively on the same SD card will have continuous time
codes.
Setting the Time Code’s Initial Value
[¤ TC/UB Setup]
[Time Code]
If you set the time code mode to [Preset], you can set the initial value of
the time code.
1 Open the time code [Setting] submenu.
[¤ TC/UB Setup] > [Time Code] > [Setting]
[Setting]
Setting the Time Code
2 Select [Set] and then press the joystick.
• The time code setting screen appears with an orange selection frame indicating the hours.
• To reset the time code to [00:00:00.00], select [Reset] instead. If the running mode is set to [Free Run], the
time code will be reset the moment you press the joystick and keep running continuously from 00:00:00.00.
71
3 Push the joystick up/down to set the hours and then press the joystick to move to the minutes.
4 Change the rest of the fields (minutes, seconds, frame) in the same way.
• Press the CANCEL button to close the screen without setting the time code.
5 Select [Set] and then press the joystick to close the screen.
• If the running mode is set to [Free Run], the time code will start running from the selected time code the
moment you press the joystick.
Selecting Drop or Non-Drop Frame
[¤ TC/UB Setup]
When [w Other Functions] > [System Frequency] is set to [59.94 Hz],
you can select between a drop frame (DF) or non-drop frame (NDF) time
code, depending on how you plan to use your recordings.
[Time Code]
In the following cases, the time code is set to non-drop frame (NDF) and
cannot be changed.
- [w Other Functions] > [System Frequency] is set to [50.00 Hz]
- [w Other Functions] > [System Frequency] is set to [59.94 Han
the frame rate is set to 24P
[DF/NDF]
[DF]
1 Open the [DF/NDF] submenu.
[¤ TC/UB Setup] > [Time Code] > [DF
2 Select [DF] or [NDF] and then prs the jo
• The time code display will differ dpending on the setting. When you select [DF], the time code will appear
as [00:00:00.00]; when you select DF], iwill appear as [00:00:00:00].
Putting the Time Code Display on Hold
If you set an assignable button to [Time Code Hold] (A 89), you can press the button to freeze the display of
the time code. While the time code display is put on hold, [H] will appear on the screen next to the time code.
The time code continues to run normally while the time code display is on hold. When you resume the time code
display, the current time code will be displayed.
About the Time Code Display
An icon may appear next to the time code depending on the operation. Refer to the following table.
Icon
R
Description
The time code is set to [Regen.].
P
The time code is set to [Preset] and the running mode is set to [Rec Run].
The time code is set to [Preset] and the running mode is set to [Free Run].
Time code display is on hold.
F
H
No icon Time code during clip playback.
Setting the Time Code
NOTES
• When the frame rate is set to 24P, the frames value in the time code runs from 0 to 23. When the frame rate is
set to 50i or PF25, it runs from 0 to 24. With other frame rates, it runs from 0 to 29.
• When pre-recording mode is activated, [Free Run] is set automatically and cannot be changed.
72
• When you mix drop frame and non-drop frame time codes, there might be a discontinuity in the time code at
the point where the recording starts.
• As long as the built-in rechargeable lithium battery is charged and you selected the [Free Run] running mode,
the time code continues to run even if you disconnect all other power sources. However, this is less accurate
than when the camcorder is on.
• If you set an assignable button to [Time Code] (A 89), you can press the button to open the [¤ TC/UB
Setup] > [Time Code] submenu.
Setting the User Bit
Setting the User Bit
The user bit display can be selected from the date or the time of
recording, or an identification code consisting of 8 characters in the
hexadecimal system. There are sixteen possible characters: the numbers
0 to 9 and the letters A to F.
[¤ TC/UB Setup]
73
[User Bit]
[Type]
Operating modes:
1 Open the user bit [Type] submenu.
[¤ TC/UB Setup] > [User Bit] > [Type]
[Setting]
2 Select the desired user bit type and then press the joystick.
• Select [Setting] to set your own identification code, [Time] to use the time as user bit, or [Date] to use the
date as the user bit.
• If you selected [Time] or [Date], you do not need to perform the rest of the procedure. If you selected
[Setting], continue the procedure to set the identification code.
3 Select [Set] and then press the joystick.
• The user bit setting screen appears with an orange selection frame on the leftmost digit.
• To reset the user bit to [00 00 00 00], select [Reset] instead.
4 Push the joystick up/down to select the first character antn press the joystick to move to the
next digit.
• Change the rest of the digits in the same way.
• Press the CANCEL button to close the scrout tting the user bit.
5 Select [Set] and then press the joystck to e screen.
NOTES
• User bit output: The user bit will be outut ong with the video output from the HDMI OUT terminal. In
mode, when the frame rate is set to PF24 or 24P, you can output the user bit as 2:3 pulldown data by setting
[¤ TC/UB Setup] > [User Bit] > [Output Mode] to [Pulldown].
Recording Audio
Recording Audio
You can record audio using the built-in stereo microphone*, commercially available microphones (XLR terminal*,
MIC terminal) or line input (XLR terminal*). Using the XLR terminals, you can select the audio input independently
for channel 1 and channel 2.
When the bit rate is set to [24 Mbps LPCM], you can enjoy two-channel linear PCM audio recording with a
sampling frequency of 48 kHz. LPCM audio playback is also available for clips recorded with that bit rate.
* Only available when the handle unit is attached to the camcorder.
74
Operating modes:
Connecting an External Microphone or External Audio Input Source to the Camcorder
In order to use the microphone holder and XLR terminals, the handle unit must be attached to the camcorder.
Follow the procedure below to attach a microphone (refer also to the following illustration). To connect an
external device to the camcorder, plug the device’s cable into the camcorder’s XLR terminal (ብ).
1 Loosen the microphone lock screw (ቢ), open the microphone holder and insert the microphone (ባ).
2 Tighten the lock screw and put the microphone cable through the microphone cable clamp under
the microphone holder (ቤ).
3 Plug the microphone cable into the desired XLR terl (ብ) the MIC terminal (ቦ).
XLR terminals
MIC terminal
Microphone lock screw
Cable clamp
CH1/CH2
AUDIO IN switches
Using the Built-in Microphone or an External Microphone
Connected to the MIC Terminal
Follow the step below to use the built-in microphone or an external microphone
attached to the MIC terminal. Use commercially available condenser microphones
with their own power supply and a ∅ 3.5 mm mini-stereo plug*. You can use the
microphone attenuator for either type of microphone. If you are using the built-in
microphone, you can also use the low-cut filter and select the sensitivity.
* For 50.00 Hz recordings, use commercially available microphones with a cable no longer than
3 m.
Set the AUDIO IN switch of the desired channel to INT.
• If you connect a microphone to the MIC terminal while the AUDIO IN switch is
set to INT, the camcorder will switch automatically from the built-in microphone
to the external microphone.
Recording Audio
Adjusting the Audio Level for the MIC Terminal
You can adjust the audio recording level of a microphone attached to the MIC terminal to auto or manual. The
way to adjust the audio level depends on whether the handle unit is attached to the camcorder.
75
CH1
dial
When the Handle Unit is Attached
With the handle unit attached, the audio level adjustment is done using the
audio controls on the handle unit.
1 Select the audio level adjustment mode with the CH1 audio level switch.
• Automatic audio level adjustment: Set the CH1 audio level switch to
A. You do not need to perform the rest of the procedure.
CH1
audio level switch
Manual audio level adjustment: Set the CH1 audio level switch to M.
Continue the procedure to set the microphone's audio recording level.
2 Turn the CH1
dial to adjust the audio level.
• For reference, 0 corresponds to -G, 5 corresponds to 0 dB, and 10
corresponds to +18 dB.
• As a guideline, adjust the audio recording level so that the audio level
meter on the screen will go to the right of the 18 dB mark (one mark right
of the 20 dB mark) only occasionally.
• Closing the protective cover will prevent the audio controls from eing
changed inadvertently.
When the Handle Unit is Not Attached
You can use an external microphone connecteIC rminal without attaching the handle unit. In such
case, adjust the microphone's audio reoing the menu.
1 Open the [MIC Mode] submenu.
[¡ Audio Setup]
[¡ Audio Setup] > [Audio Input] > [MIC ode]
2 Select [Automatic] or [Manual] and then press the joystick.
[Audio Input]
• If you selected [Automatic], you do not need to perform the rest of the
procedure. If you selected [Manual], continue the procedure to set the
microphone’s audio recording level.
[MIC Mode]
3 Open the [MIC Level] screen.
[Automatic]
[¡ Audio Setup] > [Audio Input] > [MIC Level]
4 Push the joystick up/down to set the audio recording level and then
press the joystick.
[¡ Audio Setup]
• For reference, 0 corresponds to -G, 50 corresponds to 0 dB, and
99 corresponds to +18 dB.
[Audio Input]
• As a guideline, adjust the audio recording level so that the audio level
meter on the screen will go to the right of the 18 dB mark (one mark
right of the 20 dB mark) only occasionally.
[MIC Level]
[50]
NOTES
• When adjusting the audio level manually, you can activate the audio
peak limiter with the [¡ Audio Setup] > [Audio Input] > [Limiter]
setting. When activated, the audio peak limiter will limit the amplitude of audio input signals when they exceed
-6 dBFS.
• We recommend using headphones when adjusting the audio level. If the input level is too high, audio may
become distorted even if the audio level indicator shows an appropriate level.
• If you set an assignable button to [Audio Level] (A 89), you can press the button to turn the onscreen audio
level indicator on and off.
Recording Audio
Configuring the Built-in Microphone’s Low-Cut Filter
[¡ Audio Setup]
[Audio Input]
[Int. Mic Low Cut]
[Off]
1 Open the [Int. Mic Low Cut] submenu.
[¡ Audio Setup] > [Audio Input] > [Int. Mic Low Cut]
2 Select the desired option and then press the joystick.
76
Options
[Off]:
For recording audio under usual conditions.
[LC1]: For recording mainly people’s voices.
[LC2]: For reducing the background sound of wind when recording
outdoors in windy surroundings (for example, on a beach or close to
buildings). Note that when you use this setting some low-frequency
sounds may be suppressed along with the sound of wind.
Selecting the Built-in Microphone’s Sensitivity
[¡ Audio Setup]
[Audio Input]
1 Open the [Int. Mic Sensitivity] submenu.
[¡ Audio Setup] > [Audio Input] > [Int. Mic Sensitivity]
2 Select the desired option and then press the joystick.
[Int. Mic Sensitivity]
[Normal]
Options
[Normal]: For recording audio under usual conditions.
[High]:
For recording audio at a higher volume (+6 dB).
Activating the Microphone Attenuator
[¡ Audio Setup]
[Audio Input]
[MIC/Int. Mic Att.]
[Off]
If the audio level is too high and the soud sundd when
recording with the built-in microphone r an externophone
connected to the MIC terminal, activate he micrphone attenuator (built-
in microphone: 12 dB, external micropho(MIterminal): 20 dB).
1 Open the [MIC/Int. Mic Att.] submenu.
[¡ Audio Setup] > [Audio Input] > [MIC/Int. Mic Att.]
2 Select [On] and then press the joystick.
Recording Audio
Using Audio Input from the XLR Terminals
Using the XLR terminals CH1 and CH2, you can record audio independently to the two audio channels from a
microphone or analog audio input source.
77
CH1/CH2
Switching Between Microphone and Line Input
dials
1 Set the AUDIO IN switch of the desired channel to EXT.
2 Set the XLR terminal switch of the desired channel to LINE or
MIC.
CH1/CH2
audio level
switches
• To supply a microphone with phantom power, set the switch to
MIC+48V instead. Make sure to connect the microphone first,
before turning the phantom power on. Keep the microphone
connected when turning off the phantom power.
XLR terminal
switches
• When using the XLR terminal to record to only one channel, use
the CH1 terminal.
CH1/CH2
AUDIO IN
switches
Selecting the Recording Channel
[¡ Audio Setup]
You can select to which channel the cmcorder d audio.
1 Open the [XLR Rec Channel] subme.
[Audio Input]
[XLR Rec Channel]
[CH1]
[¡ Audio Setup] > [Audio Input] > [XRec Channel]
2 Select the desired option and then press the joystick.
Options
[CH1]:
Records audio to each channel separately. Audio input
into CH1 is recorded to channel 1, while audio input into
CH2 is recorded to channel 2.
[CH1/CH2]: Audio input into CH1 is recorded to both channels. Audio
input into CH2 will not be recorded.
IMPORTANT
• When connecting a microphone or device that does not support phantom power, make sure to set the XLR
terminal switch to MIC or LINE, respectively. If you set the switch to MIC+48V, the microphone or device may
be damaged.
Recording Audio
Adjusting the Audio Level for the XLR Terminals
You can set the audio recording level for audio input from the XLR terminals to automatic or manual
independently for each channel.
78
CH1/CH2
audio level switches
Automatic Audio Level Adjustment
Set the audio level switch of the desired channel to A (automatic) to let the
camcorder automatically adjust that channel’s audio level.
NOTES
• When both CH1 and CH2 are set to the same audio input (external
microphone or external line input), if the audio level is set to automatic, you
can use the [¡ Audio Setup] > [Audio Input] > [XLR ALC Link] setting to
link the audio level adjustment of both channels.
CH1/CH2
Manual Audio Level Adjustment
dials
You can set the audio level for each channel manually from to 18 B.
1 Set the audio level switch of the desired channel M.
2 Turn the corresponding
dial to adjust leve
• For reference, 0 corresponds to -G, 5 corro 0 dB, and 10
corresponds to +18 dB.
• As a guideline, adjust the audio recding leel so that the audio level
meter on the screen will go to the right f t18 dB mark (one mark right
of the 20 dB mark) only occasionally.
CH1/CH2
audio level
switches
• Closing the protective cover will prevent the audio controls from being
changed inadvertently.
NOTES
• If at least one of the channels is set to manual audio level adjustment, you
can also activate the audio peak limiter to prevent audio distortions. When
activated, the audio peak limiter will limit the amplitude of audio input
signals when they exceed -6 dBFS. Use the [¡ Audio Setup] > [Audio
Input] > [Limiter] setting.
• We recommend using headphones when adjusting the audio level. If the input level is too high, audio may
become distorted even if the audio level indicator shows an appropriate level.
• If you set an assignable button to [Audio Level] (A 89), you can press the button to turn the onscreen audio
level indicator on and off.
Recording Audio
Adjusting the Microphone’s Sensitivity
You can adjust the microphone’s sensitivity if the XLR terminal switch is set to MIC or MIC+48V.
1 Open the desired XLR terminal’s sensitivity submenu.
79
[¡ Audio Setup] > [Audio Input] > [XLR1 Mic Trimming] or [XLR2 Mic Trimming]
2 Select the desired level and then press the joystick.
Available Sensitivity Levels
[¡ Audio Setup]
+12 dB
+6 dB
0 dB
-6 dB
-12 dB
[Audio Input]
[XLR1 Mic Trimming]
[XLR2 Mic Trimming]
[0 dB]
Activating the Microphone’s Attenuator
[¡ Audio Setup]
You can activate the microphone’s attenuator (20 dB) if the XLR ermal
switch is set to MIC or MIC+48V.
[Audio Input]
1 Open the desired XLR terminal’s microphone attenuatoenu.
[¡ Audio Setup] > [Audio Input] > [XLR1 ] or LR2 Mic
Att.]
[XLR1 Mic Att.]
[XLR2 Mic Att.]
2 Select [On] and then press the joysk.
[Off]
Monitoring the Audio with Headphones
Connect headphones* to the × (headphone) terminal to monitor the
recorded audio. You can adjust the headphone volume with the
[¡ Audio Setup] > [Audio Output] > [Headphone Volume] setting.
× (headphone)
terminal
* For 50.00 Hz recordings, use commercially available headphones with a cable no
longer than 3 m.
NOTES
• If you set an assignable button to [Headphone +] or [Headphone -]
without using the menu.
• When you are monitoring the audio, you can choose to synchronize the
audio signal with the video signal or monitor the audio in real time. Use
the [¡ Audio Setup] > [Audio Output] > [Monitor Delay] setting to
select the method. Note that there will be a slight delay when you monitor in real time. Regardless of the
setting, however, the audio and video signals recorded will be synchronized.
Color Bars/Audio Reference Signal
Color Bars/Audio Reference Signal
You can have the camcorder generate and record color bars and a 1 kHz audio reference signal and output
them from the HDMI OUT terminal, AV OUT terminal and × (headphone) terminal (audio reference signal only).
80
Operating modes:
Recording Color Bars
[~ Camera Setup]
The types of color bars available depend on the camcorder's system
frequency setting. When [System Frequency] is set to [59.94 Hz], you can
choose between SMPTE standard-definition color bars and ARIB multi-
[Color Bars]
format HDTV color bars. When [System Frequency] is set to [50.00 Hz],
you can choose between EBU color bars and SMPTE standard-definition
color bars.
[Type]
[SMPTE] or [EBU]*
1 Open the color bars [Type] submenu.
[~ Camera Setup] > [Color Bars] > [Type]
* Depending on the country/region of
purchase.
2 Select the type of color bars and then press the joystick.
3 Open the [Enable] submenu to activate the color bars.
[~ Camera Setup]
[Color Bars]
[Enable]
[~ Camera Setup] > [Color Bars] > [Enable]
4 Select [On] and then press the joystick.
• The selected color bars appear on the screll be ecorded
when you press the START/STOP button.
• Turning the camcorder off or channg the opemode to
mode will deactivate the color bars
[Off]
NOTES
• If you set an assignable button to [Color Bars] (A 89), you can press the button to activate and deactivate the
color bars.
Recording an Audio Reference Signal
[¡ Audio Setup]
The camcorder can output a 1 kHz audio reference signal with the color
bars.
[Audio Input]
1 Open the [1 kHz Tone] submenu.
[1 kHz Tone]
[Off]
[¡ Audio Setup] > [Audio Input] > [1 kHz Tone]
2 Select the desired level and then press the joystick.
• Available levels are -12 dB, -18 dB and -20 dB.
• Select [Off] to turn off the signal.
• The signal is output at the selected level and will be recorded when you press the START/STOP button.
Video Scopes
Video Scopes
The camcorder can display a simplified waveform monitor or an edge monitor* to help you focus. The video
scopes appear only on the LCD screen. They do not appear in the viewfinder or on an external monitor.
* The edge monitor looks at the focus of the entire picture and displays the results as a waveform. The edge monitor is available
81
only in
mode.
Displaying a Video Scope
Operating modes:
Press the WFM button.
• The waveform monitor will appear in a window on the lower right of the
screen.
• You can press the WFM button repeatedly to activate the video scopes
in the following sequence.
Waveform monitor ꢀ Edge monitor* ꢀ Off
• Alternatively, you can display the video scopes using [w Other
Functions] > [WFM (LCD)] > [Setting]. Select [WFM] for the waverm
monitor or [Edge Mon.]* for the edge monitor.
* Not available in
mode.
Configuring the Waveform Monitor
[w Other Functions]
[WFM (LCD)]
The camcorder’s waveform monitor fuction offers 5 des. You can also
change the gain.
Operating modes:
[Waveform Monitor]
[Line]
1 Open the [Waveform Monitor] submenu.
[w Other Functions] > [WFM (LCD)] > [Waveform Monitor]
2 Select the desired option and then press the joystick.
• If you do not need to change the gain, you do not need to perform steps 3 and 4.
3 Open the waveform monitor [Gain] submenu.
[w Other Functions] > [WFM (LCD)] > [Gain] (under [Waveform Monitor])
4 Select [1x] or [2x] and then press the joystick.
Options
[Line]:
Sets the waveform monitor to line display mode.
[Line+Spot]:
[Field]:
The waveform of the area in the red frame is displayed in red on top of the [Line] mode waveform.
Sets the waveform monitor to field display mode.
[RGB]:
Functions like an RGB parade scope.
[YPbPr]:
Functions like a YPbPr parade scope.
Video Scopes
Configuring the Edge Monitor
[w Other Functions]
[WFM (LCD)]
[Edge Monitor]
[Type 1]
Using this video scope allows you to focus with more precision. You can
use the edge monitor along with the other focus assistance functions
82
Operating modes:
1 Open the [Edge Monitor] submenu.
[w Other Functions] > [WFM (LCD)] > [Edge Monitor]
2 Select the desired option and then press the joystick.
• If you do not need to change the gain, you do not need to perform steps 3 and 4.
3 Open the edge monitor [Gain] submenu.
[w Other Functions] > [WFM (LCD)] > [Gain] (under [Edge Monitor])
4 Select the desired gain value and then press the joystick.
Options
[Type 1]: The waveform that represents the focus of the entire picture is displayed in green. In addition, the waveform
of the area in the three red frames is displayed in red on top of he previous waveform.
[Type 2]: This mode displays the edge monitor with the waveform moniin [Line+Spot] mode. The waveform
monitor appears on the left in green while the edge monitor ars on the right in blue. The waveform of
the area in the red frame is displayed in red on toedge nitor waveform.
Reviewing a Recording
Reviewing a Recording
When the camcorder is in
was recorded.
mode, you can review the last clip that
[w Other Functions]
83
Operating modes:
[Rec Review]
[Entire Clip]
1 Open the [Rec Review] submenu to set the review length.
[w Other Functions] > [Rec Review]
2 Select the desired option and then press the joystick.
3 After you finish recording, press the u button.
• The last clip that was recorded is played back without audio for the
selected duration. [Ð REVIEW] appears at the top of the screen.
• Press the CANCEL button to stop reviewing the clip and change the
camcorder back to record pause mode.
• After the clip finishes playing back, the camcorder returns to record
pause mode.
Options
[Entire Clip]: Allows you to review the entire clip.
[Last 4 sec]: Allows you to review just the last 4 seconds of the clip.
NOTES
• If the camcorder switched SD cards during a rthe camcorder
will play back the clip on the SD camost recencorded on.
Pre-recording Mode
Pre-recording Mode
When pre-recording mode is activated, the camcorder starts recording continuously into a temporary memory of
approximately 3 seconds so when you press the START/STOP button, the clip will contain also approximately 3
seconds of video and audio recorded before you pressed the button. This is especially useful when it is difficult
to predict when to start recording.
84
Operating modes:
1 Open the [Pre Rec] submenu.
[w Other Functions] > [Pre Rec]
[w Other Functions]
2 Select [On] and then press the joystick.
• [PRE REC STBY] appears at the top of the screen.
[Pre Rec]
[Off]
3 Press the START/STOP button to begin recording.
• The rear and front tally lamps illuminate.
• [PRE REC STBY] changes to [Ü PRE REC] while recording.
4 Press the START/STOP button again to stop recording.
• The camcorder records the clip, including approximately 3 seconds of video and audio recorded before the
START/STOP button was pressed.
• Both tally lamps will go out and [PRE REC STBY] appears at thp of the screen.
NOTES
• During pre-recording mode, if the camcorder icord pause mode for approximately 1 hour, a message
• Pre-recording mode cannot be used with double cording, deleting the last clip recorded or reviewing a
recording.
• During pre-recording mode, the time coe wbe recorded with the running mode (A 70) set to [Free Run],
regardless of the previous setting. When the time code is recorded, it will include the 3 seconds before the
START/STOP button was pressed. When pre-recording mode is deactivated, the running mode will return to
its previous setting.
Continuous Recording
Continuous Recording
Using continuous recording you can avoid missing important shooting opportunities. You need to activate the
continuous recording mode using the menu. Once continuous recording has started, the camcorder will keep
recording until you access the menu to stop recording. Additionally, when two SD cards are inserted in the
camcorder, activating the continuous recording mode will automatically activate also the double slot recording
function so you can have an additional copy of your continuous recording.
85
During continuous recording, you can press the START/STOP button to set in and out points* in the recording;
the portion of a clip between an in point and an out point will be defined as a "shot". In
mode, you can
display a special index screen of shots (A 105) and play back and delete specific shots. The in and out point
information can also be read by compatible NLE software** and used for editing.
* In points and Out points are marks in the continuous recording clips that indicate the beginning and end point of important parts
in the recording.
**For details about compatible software, visit your local Canon Web site.
Operating modes:
START
(in point)
STOP
START
STOP
START
STOP
START
START/STOP button
(out point) (in point) (out point)
(in point) (out point) (in point)
(out point)
Shots
Shots
Continuous reclip)
top]
Continuous recording (clip)
[Start]
Menu operation
([Continuous Rec] >
[Start/Stop])
[Start]
(start recording)
[Stop]
(stop recording)
stop recording) (start recording)
1 Open the continuous recording [Moe] bmenu.
[w Other Functions] > [Continuous Rec] > [Mode]
[w Other Functions]
2 Select [On] and then press SET.
[Continuous Rec]
[Mode]
• [CONT STBY] or [4CONT STBY] (when using two SD cards)
appears at the top of the screen and the camcorder will enter
continuous recording standby mode.
• The total shot recording time (4CONT 00:00:00) will appear on the
left of the screen.
[Off]
3 Press the START/STOP button to begin recording.
• The rear and front tally lamps illuminate and continuous recording will
start. [CONT] will be displayed in red and the time code will start
running.
[w Other Functions]
[Continuous Rec]
[Start/Stop]
• At the same time, the first shot's in point is recorded. [STBY] changes
to [Ü REC] and the total shot recording time will start advancing.
• You can also set [w Other Functions] > [Continuous Rec] > [Start/
Stop] to [Start] to start recording.
[Start]
4 Press the START/STOP button as necessary to set additional in
and out points.
• While recording: An out point is recorded, [Ü REC] changes to [STBY] and the total shot recording time will
stop advancing.
• During standby mode: An in point is recorded, [STBY] changes to [Ü REC] and the total shot recording time
will start advancing again.
Continuous Recording
5 To stop the continuous recording, open the continuous recording [Start/Stop] submenu.
[w Other Functions] > [Continuous Rec] > [Start/Stop]
6 Select [Stop] and then press SET.
• Continuous recording will stop. Both tally lamps will go out and the clip will be recorded on the SD card(s).
• [CONT] will change back to white and the time code will stop.
86
• If a shot was being recorded while the menu was accessed, stopping the continuous recording will
automatically record also an out point for that shot.
7 To end the continuous recording mode, open the continuous recording [Mode] submenu.
[w Other Functions] > [Continuous Rec] > [Mode]
8 Select [Off] and then press SET.
• [CONT] and the total shot recording time display will disappear.
NOTES
• When using two SD cards for continuous recording, even if continuous recording is not possible on one SD
card because the maximum number of clips (200 clips) has been reached, continuous recording may continue
only on the other SD card as long as continuous recording clips can still be recorded on that SD card.
• During continuous recording mode, relay recording, pre-recording, reviewing a recording or deleting the last
clip recorded cannot be used.
• Immediately after activating the continuous recording mode or opg a continuous recording, the onscreen
[CONT] display will flash momentarily. During this time, segs in tContinuous Rec] submenu cannot be
changed. Wait until the onscreen display stops flashing ys on change other settings.
Using the RC-V100 Remote Controller
Using the RC-V100 Remote Controller
You can connect the optional RC-V100 Remote Controller to control the camcorder (including advanced
recording functions) from a distance. In addition to turning the camcorder on and off and navigating the menus,
while recording you can control various camera functions, such as aperture and shutter speed, and custom
picture settings, like knee and sharpness.
87
The connection cable supplied with the RC-V100 is required to connect the remote controller to the camcorder's
REMOTE terminal. For details on how to connect and use the remote controller, refer to its instruction manual.
Operating modes:
Con cabl
(suppe RC-V)
1 Turn off the camcorder and connect the optional RC-V100
[w Other Functions]
Remote Controller to the camcorder.
2 Turn on the camcorder in
Term.] submenu.
[w Other Functions] > [REMOTE Term.]
3 Select [RC-V100] and then press the joystick.
Options
mode and open the [REMOTE
[REMOTE Term.]
[Standard]
[RC-V100]:
[Standard]:
Select this option to use the optional RC-V100 Remote Controller.
Select this option to use commercially available remote controls.
NOTES
• The following controls on the remote controller will not operate the camcorder: ND button, AGC button, AUTO
KNEE button, ZOOM dial and AF button.
• The AUTO IRIS button on the remote controller will operate the camcorder only when a compatible EF lens
• Custom picture settings can be changed using the remote controller only when an appropriate custom picture
Using the RC-V100 Remote Controller
88
Customization
4
89
Assignable Buttons
The camcorder conveniently features 15* buttons to which you can assign various functions. By assigning often-
used functions, you can quickly access them with a single press of a button. Assignable button 7 is located on
the grip unit, so its availability depends on the camcorder configuration used.
* In
mode, only assignable buttons 7 to 15 are available.
Operating modes:
(on the grip unit)
Changing the Assigned Function
[w Other Functions]
1 Open the [Assign Button] submenu.
[w Other Functions] > [Assign Button]
[Assign Button]
2 Select the button to change and then press the joystick.
• A list of available functions appears.
[1 to 6 (NONE)]
[7 MAGN.]
• The quick reference shows the default settings for each assignable
button. The labels on the camcorder/grip unit for assignable buttons
7 to 15 also indicate their default settings. By default, buttons 1 to 6
have no assignable function set.
[8 MAGN.]
[9 PEAKING]
[10 ZEBRA]
[11 WFM]
[12 PUSH AUTO IRIS]
[13 ISO/GAIN]
[14 SHUTTER]
[15 ONE-SHOT AF]
3 Select the desired function and then press the joystick.
• If you selected [User Setting (NONE)], the menu will change from
orange to blue to indicate you are selecting a menu setting to register.
Continue the procedure to register a menu setting. Otherwise, you do
not need to perform the rest of the procedure.
Assignable Buttons
4 Navigate the menus to find the menu setting you want to register and then press the joystick.
• The selected menu setting will be registered to the customizable slot and to the assignable button.
• The name of the selected menu setting will be listed instead of [User Setting (NONE)] and the customizable
slot will be marked by a
.
90
NOTES
• You can check the two [Assign Button] status screens (A 142) to see what functions are set for the
assignable buttons.
• You can reset only the functions assigned to the assignable buttons, without affecting other camera settings,
with the [w Other Functions] >[Reset] > [Assignable Buttons] function. All the assignable buttons will return
to their default function.
Using an Assignable Button
After you assign a function to one of the buttons, press the button to activate the function. For some functions,
an options menu may appear. In such case, select the desired option and then press the joystick.
Assignable Functions
Functions can be set separately in
mode and
mode. Refer to the following table for assignable
functions and available modes.
Function name
Description
A
[ONE-SHOT AF]
[PUSH AUTO IRIS]
[Iris Mode]
[Iris +]
The camcorder focuses automatically one time only AF funct).
The camcorder automatically adjusts th(f/sto
Switches the aperture adjustment mode omatand manual.
Opens up the aperture.
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
–
–
–
–
–
–
–
–
–
–
–
–
–
–
[Iris -]
Closes the aperture.
[AE Shift +]
[AE Shift -]
[Backlight]
[Spotlight]
[ISO/GAIN]
[SHUTTER]
[View Assist.]
[PEAKING]
[ZEBRA]
Compensates the exposure towd the right side.
Compensates the exposure toward the dark side.
Turns the [Backlight] light metering option on/off.
Turns the [Spotlight] light metering option on/off.
Highlights the ISO speed or gain value so it can be adjusted.
Highlights the shutter speed so it can be adjusted.
Turns view assistance on/off.
Turns peaking on/off.
Turns zebra patterns on/off.
Activates video scopes in the following sequence:
[WFM]
Ü
Ü
Waveform monitor J Edge monitor (
mode only) J Off
[MAGN.]
Turns magnification on/off.
Ü
Ü
Ü
Ü
Ü
Ü
–
–
[Color Bars]
[Markers]
Turns color bars on/off.
Turns onscreen markers on/off.
Opens the [LCD Setup] submenu.
Opens the [VF Setup] submenu.
–
[LCD Setup]
[VF Setup]
[LCD/VF B&W]
Ü
Ü
Ü
Turns the B&W mode of the LCD and viewfinder on/off.
Turns on/off the inclusion of onscreen displays on video output from the camcorder’s
terminals (both HD and SD video output).
[Onscreen Display]
[Time Code]
Ü
Ü
Displays the [Time Code] submenu.
Ü
Ü
–
[Time Code Hold]* Puts the time code display on hold or resumes it.
Ü
Assignable Buttons
Function name
[Headphone +]
[Headphone -]
[Speaker +]
[Speaker -]
Description
A
Increases the headphone volume.
Reduces the headphone volume.
Ü
Ü
–
Ü
Ü
Increases the built-in speaker's volume.
Reduces the built-in speaker's volume.
Switches the audio output channel.
Turns the audio level meter on/off.
Ü
Ü
91
–
[Audio Output CH]
[Audio Level]
[Photo]*
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Records a photo.
Ü
[Fan]
Switches the cooling fan’s operation between always on and automatic.
Opens the [My Menu] customized submenu.
Opens the [Initialize Media] submenu.
Replaces the joystick's up arrow.
–
[My Menu]
–
[Initialize Media]
Ü
[
[
[
[
Up]
Ü**
Ü**
Ü**
Ü**
Down]
Left]
Replaces the joystick's down arrow.
Replaces the joystick's left arrow.
–
Right]
Replaces the joystick's right arrow.
Replaces the joystick's SET button. That is, pressing the assignable button is the same
as pressing down the joystick itself.
[
SET]
Ü
Ü
Ü**
[User Setting
(NONE)]*
Customizable slot. Assign to the button any menu setting you wouike to register.
Ü
* Function can be used only by assigning it to a button.
**Not available during photo playback.
Custom Picture Settings
Custom Picture Settings
You can preset a number of picture-related settings (A 95). You can change each individual setting for
maximum control or use a more intuitive graphical interface to adjust the gamma curve and white balance shift
(A 101). After adjusting the desired settings to your preference, you can save the whole set in the camcorder or
SD card as a custom picture file. You can then load the file at a later date to change the current settings to the
preset levels you selected. You can even use the [w Other Functions] > [Photos] > [Add / File] setting to
embed the custom picture settings in photos recorded to an SD card.
92
You can save up to 9 different custom picture files on the camcorder and up to 20 custom picture files on an SD
card. Custom picture files can be copied between the camcorder and SD card.
Custom picture files created with previous Canon camcorders are not compatible with this camcorder. Custom
picture files created with this camcorder are compatible only with other C100 camcorders.
Operating modes:
Selecting Custom Picture Files
Select a custom picture file to apply its settings to your recordings or to
edit, rename, protect, or transfer it. When [~ Camera Setup] >
[/ CINEMA Locked] is set to [On], the custom picture menu caot e
accessed and custom picture files cannot be used.
1 Press the CUSTOM PICTURE button.
• The custom picture menu appears. The currlectfile
appears next to the - icon or [Off] if no file d.
• When an optional RC-V100 RemoControllected to the
camcorder, you can also press the emote contr's CUSTOM
PICT. button to open the custom piure sumenu.
2 Select [- / Select File] and then press the joystick.
3 Select the location of the custom picture file and then press the
joystick.
• Select [Camera] to apply a custom picture file saved in the camcorder or [*A] or [*B] to apply a custom
picture file saved on the respective SD card.
• [*A] and [*B] will only appear if the SD card contains previously saved custom picture files.
4 Select the desired file and then press the joystick.
• Select [Off] to record without applying any custom picture settings.
• To apply the file’s settings, press the CUSTOM PICTURE button to exit the custom picture menu. An icon
representing the selected custom picture file will appear on the left of the screen.
• To perform other operations on the file, continue with the following procedures.
Preset Custom Picture Files
By default, the custom picture files in the camcorder in file slots [C7] to [C9] are protected. Remove the
[C7: EOS Std.]: Reproduces the image quality and look (high contrast, vibrant colors) of an EOS digital SLR
camera with its picture style set to [Standard].
[C8: Wide DR]: Applies a gamma curve with a very wide dynamic range and an appropriate color matrix that
nevertheless do not require post-production processing.
[C9: CINEMA]: Uses the Canon Log gamma and color matrix for an outstanding dynamic range and an
image suitable for processing in post-production.
Custom Picture Settings
NOTES
• About changing custom picture related settings using the optional RC-V100 Remote Controller
- If a protected custom picture file or no custom picture file is selected on the camcorder ([- / Select File]
is set to [Off]) custom picture related settings cannot be changed using the remote controller.
- While the remote controller is connected to the camcorder, custom picture files on an SD card ([A1] to [A20]
for SD card A, [B1] to [B20] for SD card B) cannot be used. If you connect the remote controller while a
custom picture file on an SD card was selected, the custom picture file will change automatically to [Off]
(recording without custom picture settings). To use the settings of a custom picture file saved on an SD card,
93
- Adjusting custom picture related settings using the remote controller will change the settings registered
under the currently selected custom picture file. If you want to keep an important custom picture file, copy it
in advance to an SD card or select in advance a custom picture file you do not mind changing.
Editing a Custom Picture File’s Settings
This procedure describes how to change the custom picture settings in detail when you want maximum control
over the image. In addition, the camcorder offers an easier, more intuitive way to adjust only the gamma curve
1 After selecting a file, select [ / Fine Tuning] and then prethe joystick.
2 Select a setting and then press the joystick.
3 Change the setting to the desired level and then pe joystk.
• Repeat steps 2 and 3 for other settings, as y.
4 Press the CUSTOM PICTURE bton to exit ustom picture menu and apply the new custom
picture settings.
Resetting the current file’s settings to default values
[
/ Fine Tuning]
1 After selecting a file, open the [Reset] submenu.
/ Fine Tuning] > [Reset]
[
[Reset]
2 Select the desired default values and then press the joystick.
• Select [NEUTRAL] to reset to neutral default values (equivalent to not
using custom picture settings at all) or one of the preset settings ([CINEMA], [Wide DR] or [EOS Std.]) if you
want to replicate these preset settings, for example as a starting point to edit them further.
3 Select [OK] and then press the joystick.
Renaming Custom Picture Files
[
/ Fine Tuning]
1 After selecting a file, open the [Rename] submenu.
/ Fine Tuning] > [Rename]
[
[Rename]
• A screen appears that displays the current file name with an orange
selection frame on the first character.
2 Push the joystick up/down to select an alphanumeric character or symbol and then press the
joystick to move to the next field.
• Change the rest of the name in the same way.
Custom Picture Settings
3 Select [Set] and then press the joystick.
4 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom
picture settings.
94
Protecting Custom Picture Files
[
/ Fine Tuning]
Protecting a custom picture file prevents its settings from being
accidentally changed.
[Protect]
1 After selecting a file, open the [Protect] submenu.
[
/ Fine Tuning] > [Protect]
2 Select [Protect] and then press the joystick.
• In the custom picture menu, i will appear next to the file name.
• To remove protection settings, select [Unprotect] instead.
3 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom
picture settings.
Transferring Custom Picture Files
You can transfer custom picture files between the camcordd SD cards. When the custom picture file is in
the camcorder, use [Copy To *] or [Load From endg on the operation you wish to perform. Similarly,
when the custom picture file is on an SD card, uo Cm.] or [Load From Cam]. Custom picture files
cannot be copied directly from one SD ard to an
Copying a File from the Camcordeto n SD Card
[+ / Transfer File]
1 After selecting a file in the camcorder, open the [Copy To *] submenu.
[+ / Transfer File] > [Copy To *]
[Copy To *]
2 Select [*A] or [*B] and then press the joystick.
3 Select the file slot on the SD card under which to save the file and then
press the joystick.
• If there are available slots, you can select [New File] to save the file in the first available slot.
4 Select [OK] and then press the joystick.
• The currently selected file will be copied to the selected slot on the SD card, overwriting the file in that slot.
When the confirmation screen appears, press the joystick.
5 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom picture
settings.
Replacing a File in the Camcorder with a File on an SD Card
[+ / Transfer File]
1 After selecting a file in the camcorder to replace, open the [Load
From *] submenu.
[Load From *]
[+ / Transfer File] > [Load From *]
2 Select [*A] or [*B] and then press the joystick.
3 Select the file to transfer to the camcorder and then press the joystick.
Custom Picture Settings
4 Select [OK] and then press the joystick.
• The file in the camcorder will be overwritten by the one on the SD card. When the confirmation screen
appears, press the joystick.
5 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom picture
settings.
95
Copying a File from an SD Card to the Camcorder
[+ / Transfer File]
1 After selecting a file on an SD card, open the [Copy To Cam.] submenu.
[+ / Transfer File] > [Copy To Cam.]
[Copy To Cam.]
2 Select the file slot under which to save the file and then press the
joystick.
3 Select [OK] and then press the joystick.
• The currently selected file will be copied to the selected slot on the camcorder, overwriting the file in that
slot. When the confirmation screen appears, press the joystick.
4 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom picture
settings.
Replacing a File on an SD Card with a File in the Camcoer
[+ / Transfer File]
1 After selecting a file on an SD card to replace, open the [Load o
Cam.] submenu.
[Load From Cam.]
[+ / Transfer File] > [Load From Cam.]
2 Select the file to transfer to the SD card and ss tjoystick.
3 Select [OK] and then press the joystick.
• The file on the SD card will be ovwritten by in the camcorder. When the confirmation screen
appears, press the joystick.
4 Press the CUSTOM PICTURE button texit he custom picture menu and apply the selected custom picture
settings.
NOTES
Available Custom Picture Settings
The following are the available settings. Even if no custom picture file is selected, the default settings are still
applied to the picture.
[Gamma]
The gamma curve changes the overall look of the image. Generally, this should be the same setting as [Select]
under [Color Matrix]. (Default: [Normal 1]).
[Normal 1] to [Normal 4]: These settings are suitable for viewing the image on a TV monitor. Highlights in [Normal
2] are brighter than those of [Normal 1]. Dark tones in the lower part of the gamma
curve for [Normal 3] (ITU-R BT.709 standard) and [Normal 4] are more pronounced than
those of [Normal 2].
[Cine 1] or [Cine 2]:
Use [Cine 1] for a gamma curve that results in a picture with a cinema-like feel and
cinema-like tones. [Cine 2] has softer contrasts than does [Cine 1] but is also suitable
for creating a cinema-like picture.
[EOS Std.]:
This gamma curve approximates the look of an EOS digital SLR camera when the
picture style is set to [Standard] (high contrast, vibrant colors).
Custom Picture Settings
[Wide DR]:
Applies a gamma curve with a very wide dynamic range, optimized for playback on an
HDTV.
[Canon Log]:
Applies a logarithmic gamma curve for outstanding dynamic range. Requires image
processing in post-production.
96
Gamma
Canon log
Cine 1
Cine 2
Normal 2/3/4
Normal 1
Wide DR
Canon Log
Normal 4
Normal 3
Normal 1/2
Input
Input
[Black]
Controls the black level and color cast of blacks.
[Master Pedestal]
The master pedestal increases or decreases the black level. Highr ttings will make dark areas brighter but
decrease contrast. This setting can be adjusted from -. (Deflt: 0)
[Master Black]
Corrects color cast in blacks.
[Red]: -50 to 50 (Default: 0)
[Green]: -50 to 50 (Default: 0)
[Blue]: -50 to 50 (Default: 0)
[Black Gamma]
Controls the lower part of the gamma curve (dark areas of the image). When [Gamma] is set to [Wide DR] or
[Canon Log], this setting has no effect on the picture.
[Level]: Raises or lowers the lower part of the gamma curve. This setting can be adjusted from -50 to 50.
(Default: 0)
[Range]: Selects the range in which dark areas are affected. This setting can be adjusted from -5 to 50.
(Default: 0)
[Point]: Determines the shape of the lower part of the gamma curve. This setting can be adjusted from -1 to 50.
(Default: 0)
Black Gamma
Point
Input
Custom Picture Settings
[Low Key Satur.]
Adjusts color saturation in dark areas.
[Enable]: Activates/deactivates the setting. (Default: [Off])
[Level]: Specifies how saturated colors are in dark areas. This setting can be adjusted from -50 to 50. (Default:
0)
97
[Knee]
Controls the upper part of the gamma curve (highlights of the image). By compressing the highlights, you can
prevent parts of the image from being overexposed. When [Gamma] is set to [Cine 1], [Cine 2], [EOS Std.], [Wide
DR] or [Canon Log], this setting has no effect on the picture.
[Enable]:
[Slope]:
Activates/deactivates the setting. (Default: [On])
Determines the slope of the gamma curve above the knee point. This setting can be adjusted from
-35 to 50. (Default: 0)
[Point]:
Sets the knee point of the gamma curve. This setting can be adjusted from 50 to 109. (Default: 95)
[Saturation]: Adjusts color saturation in highlights. This setting can be adjusted from -10 to 10. (Default: 0)
Knee Slope Knee Point
Input
Input
[Sharpness]
Sets the sharpness of the output and recording signal.
[Level]: Sets the sharpness level. This setting can be adjusted from -10 to 50. (Default: 0)
[H Detail Freq.]: Sets the center frequency of horizontal sharpness. Setting higher values increases the
frequency, which, in turn, increases the sharpness. This setting can be adjusted from -8 to 8.
(Default: 0)
[Coring]:
Reduces noise artifacts caused by high sharpness levels.
[Level]: Sets the coring level. Higher values prevent sharpness from being applied to minute details, resulting in
less noise. This setting can be adjusted from -30 to 50. (Default: 0)
[D-Ofst]: You can use [D-Ofst], [D-Curve] and [D-Depth] to adjust the coring level based on brightness. [D-Ofst]
sets the coring level of the minimum brightness level. This setting can be adjusted from 0 to 50. (Default: 0)
[D-Curve]: Sets the curve of the coring adjustment. This curve is the change from [Level] to [D-Ofst]. This setting
can be adjusted from 0 to 8. (Default: 0)
[D-Depth]: Sets a multiplier to [D-Ofst] that determines the coring level adjustment based on brightness.
Positive values raise the coring level in dark areas and negative values lower the level. This setting can be
adjusted from -4 to 4. (Default: 0)
[HV Detail Bal.]: Adjusts the ratio between horizontal and vertical detail. Higher values emphasize vertical detail
while lower values emphasize horizontal detail. This setting can be adjusted from -8 to 8.
(Default: 0)
[Limit]:
Restricts how much sharpness is applied. This setting can be adjusted from -50 to 50.
(Default: 0)
Custom Picture Settings
[Select]:
In addition to the sharpness set by [Level], [Select] sets the sharpness for areas with higher
frequencies. Higher values apply more sharpness to areas with higher frequencies. Use this for
subjects in which normal sharpening is not effective. This setting can be adjusted from 0 to 15.
(Default: 0)
98
[
Knee Aperture]: Allows you to set the sharpness of only the areas above the knee point by adjusting the gain and
slope. This is not available when [Gamma] is set to [Cine 1], [Cine 2], [Canon Log] or [EOS Std.].
[Gain]: Sets the amount of sharpness. This setting can be adjusted from 0 to 9. (Default: 0)
[Slope]: Sets the slope of the sharpness. This setting can be adjusted from 0 to 3, with 0 having no slope, 1
having a steep slope and 3 having a gradual slope. (Default: 1)
[Level Depend]: Lowers the amount of sharpness applied to dark areas of the image.
[Level]: Sets the brightness of the dark areas of the image that will be affected. This setting can be adjusted
from 0 to 50. (Default: 0)
[Slope]: Determines the slope of the area between the upper and lower parts of the gamma curve. This setting
can be adjusted from 0 to 3, with 0 having no slope, 1 having a steep slope and 3 having a gradual slope.
(Default: 0)
[Offset]: Adjusts the sharpness level of dark areas in the image. Setting higher values will lower the sharpness
level. This setting can be adjusted from 0 to 50. (Default: 0)
[Noise Reduction]
Reduces the amount of noise that appears in the image. Select a leverom 1 (lowest level) to 12 (highest level),
or select [Off] to turn the noise reduction off. (Default: [Off])
[Skin Detail]
The camcorder applies a softening filter to areas ipictith skin tones to give a more pleasant
appearance. By changing these settings, you caine hat areas will be detected as skin tones. A zebra
pattern will appear over areas on the screethat ted as having skin tones.
[Effect Level]: Adjusts the level of the fir. The avaiptions are [Off], [Low], [Middle] and [High]. (Default:
[Off])
[Hue]:
Adjusts the hue for detectioof sin tones. This setting can be adjusted from -16 to 16.
(Default: 0)
[Chroma]:
[Area]:
Adjusts the color saturation for detection of skin tones. This setting can be adjusted from 0 to 31.
(Default: 16)
Adjusts the color range for detection of skin tones. This setting can be adjusted from 0 to 31.
(Default: 16)
[Y Level]:
Adjusts the brightness for detection of skin tones. This setting can be adjusted from 0 to 31.
(Default: 16)
[Selective NR]
The camcorder detects the characteristics of a certain color or tone and applies a noise reduction filter to the
targeted areas. A zebra pattern will appear over targeted areas on the screen.
[Effect Level]:Adjusts the level of the noise reduction filter. The available options are [Off], [Low], [Middle] and
[High]. (Default: [Off])
[Hue]:
Adjusts the hue for the color to be detected. This setting can be adjusted from 0 to 31. (Default: 0)
[Chroma]:
Adjusts the color saturation for the color to be detected. This setting can be adjusted from 0 to 31.
(Default: 16)
[Area]:
Adjusts the color range for the color to be detected. This setting can be adjusted from 0 to 31.
(Default: 16)
[Y Level]:
Adjusts the brightness for the color to be detected. This setting can be adjusted from 0 to 31.
(Default: 16)
Custom Picture Settings
[Color Matrix]
Color matrix affects the color tones throughout the whole image. When [Gamma] is set to [Canon Log], this
setting has no effect on the picture.
[
Select]: Available options are [Normal 1] to [Normal 4], [Cine 1] and [Cine 2], [EOS Std.], [Wide DR] and [Canon
Log]. Generally, this should be the same setting as [Gamma]. After selecting an option, you can make
more precise adjustments. (Default: [Normal 1])
99
[Gain]: Adjusts the color intensity. This setting can be adjusted from -50 to 50. (Default: 0)
[Phase]: Adjusts the color phase. This setting can be adjusted from -18 to 18. (Default: 0)
[R-G]: The R-G matrix changes the tint of the picture along the cyan/green and red/magenta gradations. This
setting can be adjusted from -50 to 50. (Default: 0)
[R-B]: The R-B matrix changes the tint of the picture along the cyan/blue and red/yellow gradations. This
setting can be adjusted from -50 to 50. (Default: 0)
[G-R]: The G-R matrix changes the tint of the picture along the magenta/red and green/cyan gradations. This
setting can be adjusted from -50 to 50. (Default: 0)
[G-B]: The G-B matrix changes the tint of the picture along the magenta/blue and green/yellow gradations.
This setting can be adjusted from -50 to 50. (Default: 0)
[B-R]: The B-R matrix changes the tint of the picture along the yellow/red and blue/cyan gradations. This
setting can be adjusted from -50 to 50. (Default: 0)
[B-G]: The B-G matrix changes the tint of the picture along the yellw/green and blue/magenta gradations.
This setting can be adjusted from -50 to 50. (Default: 0)
[White Balance]
Adjusts the amount of white balance throughout the whoe.
[R Gain]: Adjust the intensity of red tones. This an badjusted from -50 to 50. (Default: 0)
[B Gain]: Adjust the intensity of blue tones. This n be adjusted from -50 to 50. (Default: 0)
[Color Correction]
The camcorder detects the characterists of a ertain color (color phase, chroma, area and Y level) and corrects
them when recording. You can set the color correction for up to two different areas (A and B).
[Select Area]: Selects the area or areas to correct. Available options are [Area A], [Area B] and [Area A&B].
Select [Off] to turn this setting off. (Default: [Off])
[Area A Setting]: Determines the area in which colors will be corrected.
[Phase]: Adjusts the color phase for area A. This setting can be adjusted from 0 to 31. (Default: 0)
[Chroma]: Adjusts the color saturation for area A. This setting can be adjusted from 0 to 31. (Default: 16)
[Area]: Adjusts the color range for area A. This setting can be adjusted from 0 to 31. (Default: 16)
[Y Level]: Adjusts the brightness for area A. This setting can be adjusted from 0 to 31. (Default: 16)
[Area A Revision]: Sets the amount of correction for area A.
[Level]: Adjusts the amount of correction to the color saturation. This setting can be adjusted from -50 to 50.
(Default: 0)
[Phase]: Adjusts the amount of correction to the color phase. This setting can be adjusted from -18 to 18.
(Default: 0)
[Area B Setting]: Determines the area in which colors will be corrected.
[Phase]: Adjusts the color phase for area B. This setting can be adjusted from 0 to 31. (Default: 0)
[Chroma]: Adjusts the color saturation for area B. This setting can be adjusted from 0 to 31. (Default: 16)
[Area]: Adjusts the color range for area B. This setting can be adjusted from 0 to 31. (Default: 16)
[Y Level]: Adjusts the brightness for area B. This setting can be adjusted from 0 to 31. (Default: 16)
Custom Picture Settings
[Area B Revision]: Sets the amount of correction for area B.
[Level]: Adjusts the amount of correction to the color saturation. This setting can be adjusted from -50 to 50.
(Default: 0)
[Phase]: Adjusts the amount of correction to the color phase. This setting can be adjusted from -18 to 18.
(Default: 0)
100
[Other Functions]
[Setup Level]: Adjusts the black level set by the [Black] and [Master Pedestal] settings.
[Level]: Determines the amount of adjustment to be made. This setting can be adjusted from -50 to 50.
(Default: 0)
[Press]: Compresses the dynamic range of the video signal so that it does not exceed 100%. Available options
are [On] and [Off]. (Default: [Off])
[Clip At 100%]: When the video signal exceeds 100%, this function clips the white level at 100%. Available
options are [On] and [Off]. (Default: [Off])
NOTES
• When an optional RC-V100 Remote Controller is connected to the camcorder, the following custom picture
settings can be changed using the buttons and dials on the remote controller. They cannot be changed from
the camcorder while the RC-V100 is connected.
- [Black] > [Master Pedestal]; [Black] > [Master Black] > [Red], Blue]
- [Black Gamma] > [Level]
- [Knee] > [Slope] and [Point] (only when [Knee] > [Eis set [On])
- [Sharpness] > [Level]
- [White Balance] > [R Gain], [B Gain]
Custom Picture Settings
Simplified Graphical Interface
In addition to the very detailed settings explained in the previous section (A 95), the camcorder offers a more
intuitive graphical interface for adjusting the gamma curve and white balance settings. Instead of remembering
numeric values, you can see how your changes affect the gamma curve or white balance shift right on the
screen.
101
Gamma Curve
[, / Edit File]
1 After selecting a file, open the gamma curve adjustment screen.
[, / Edit File] > [Gamma]
[Gamma]
• The current gamma curve will be displayed on the screen.
2 Push the joystick left/right to highlight the [M] field and then push the
joystick up/down to select the desired basic gamma curve.
• The numbers correspond to the [Gamma] settings explained
1 to 4: [Normal 1] to [Normal 4]
7: [EOS Std.]
5 and 6: [Cine 1] and [Cine 2]
8: [Wide DR]
9: [Canon Log]
3 Push the joystick left/right to highlight the [H] field or [L] field and then
push the joystick up/down to adjust the gamma curve as necessa.
• The [L] value can be adjusted from 1 to 9. It is equivalent to e [ack Gamma] setting and controls the
lower part of the gamma curve (dark areas of the imaThis sng is not available when the [M] value is
set to 8 or 9.
• The [H] value can be adjusted from 1 to 5. It ivaleo the [Knee] setting and controls the upper part of
the gamma curve (highlights of the image). ng inot available when the [M] value is set to 5 or
higher.
4 Push the joystick left/right to select Set] and thes the joystick.
• The adjusted gamma curve will be aved. he [Gamma] value under the [ / Fine Tuning] submenu will
change accordingly.
5 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom picture
settings.
White Balance
[, / Edit File]
1 After selecting a file, open the white balance shift screen.
[, / Edit File] > [White Balance]
[White Balance]
• The current white balance is shown as an orange point at the
center of the WB correction coordinates.
2 Push the joystick left/right to shift the white balance along the blue
(B)/amber (A) gradation. Push the joystick up/down to shift the white
balance along the green (G)/magenta (M) gradation.
• The white balance shift can be set to one of 9 levels in each
color's direction.
• The amount of white balance shift will be displayed as two
coordinates in the [SHIFT] box to the left of the graph.
3 Press the joystick.
• The adjusted white balance shift value will be saved. The [White Balance] value under the [ / Fine
Tuning] submenu will change accordingly.
4 Press the CUSTOM PICTURE button to exit the custom picture menu and apply the selected custom picture
settings.
Customizing Functions and Onscreen Displays
Customizing Functions and Onscreen Displays
Customize the camcorder to match your shooting style and needs. Use the [w Other Functions] > [Custom
Function] setting to adjust how some of the camcorder’s controls and functions operate in
mode.
Similarly, use the [£ LCD/VF Setup] > [Custom Display 1] or [Custom Display 2] setting to customize the
onscreen displays that appear during recording. You can save these preferences along with other menu settings
102
Customizing Functions
[w Other Functions]
The following table describes which functions can be customized using
[Custom Function].
[Custom Function]
Operating modes:
1 Open the [Custom Function] submenu.
[w Other Functions] > [Custom Function]
2 Select the desired function.
3 Change the setting option and then press the joystick.
Customizable Functions with [Custom Function]
Menu item
[Shockless WB]
[AE Response]
ription
When this function is set to [On], it cretranion when the white balance is changed.
Controls the camcorder’s repon([Faor [Slow]) when you change the automatic exposure setting.
Changes the direction of tadjustment ([Nor [Reverse]) when operating the control dial on the grip unit.
[Grip Ctrl Dial Dir.]
Automatically switches the seen to BW while the focus assist functions (peaking and magnification) are activated. You
can have the screen switch to Bly when peaking is activated ([Peaking]), only when the magnification is activated
([Magnify]) or when either function is activated ([Both]).
[F. Assist. B&W]
Simultaneously activates peaking ([Peaking]) or displays the edge monitor ([Edge Mon.]) whenever the magnification
function is used.
[Magn. Add. Disp.]
[Scan Reverse Rec] Inverts the recorded image horizontally ([Horizontal]), vertically ([Vertical]) or both ([Both]).
[Character Rec]
When this function is set to [On], all of the onscreen displays will be recorded to the clip exactly as they appear on the screen.
Selects whether the START/STOP button will be active or locked too when the Q switch is set to C (key lock)
[C START/STOP]
Customizing Onscreen Displays
[£ LCD/VF Setup]
For details on which onscreen displays can be customized, refer to
[Custom Display 1]
[Custom Display 2]
Operating modes:
1 Open the [Custom Display 1] or [Custom Display 2] submenu.
[£ LCD/VF Setup] > [Custom Display 1] or [Custom Display 2]
2 Select the desired onscreen display.
3 Change the setting option and then press the joystick.
Saving and Loading Camera Settings
Saving and Loading Camera Settings
After you adjust custom picture settings and settings in the various menus, you can save those settings on an
SD card. You can load those settings at a later date or on another C100 camcorder so that you can use that
camcorder in that same exact way.
103
Operating modes:
Saving Camera Settings to an SD Card
[w Other Functions]
1 Open the [Save To *] submenu.
[w Other Functions] > [Transfer Menu//] > [Save To *]
[Transfer Menu//]
2 Select [*A] or [*B] and then press the joystick.
[Save To *]
3 Select [Menu] or [Menu+/] and then press the joystick.
• Selecting [Menu] will save menu settings and [Menu+/] will save
menu and custom picture settings.
4 Select [OK] and then press the joystick.
• The current settings are saved to the SD card. If the SD card alrdy has camera settings on it, they will be
overwritten.
5 When the confirmation screen appears, press the k.
Loading Camera Settings from an SD
[w Other Functions]
1 Open the [Load From *] subme.
[w Other Functions] > [Transfer Menu//] > [Load From *]
[Transfer Menu//]
2 Select [*A] or [*B] and then press the joystick.
[Load From *]
3 Select [Menu] or [Menu+/] and then press the joystick.
• Selecting [Menu] will load menu settings and [Menu+/] will load
menu and custom picture settings.
4 Select [OK] and then press the joystick.
5 When the confirmation screen appears, press the joystick.
NOTES
• The SD card includes a text file that lists the camera settings. You can check the settings by using a USB card
reader to access the SD card on a computer. In the “PRIVATE\CAMSET” folder, open the file “CAMSET4.TXT”.
• When loading camera settings from an SD card, even protected custom picture files in the camcorder will be
replaced.
• Only camera settings from other Canon C100 camcorders can be used with this camcorder.
Saving and Loading Camera Settings
104
Playback
5
105
Playback
This section explains how to play back clips recorded on an SD card. For details on playing back clips using an
external monitor, refer to Connecting to an External Monitor (A 118). For details on viewing photos, refer to
Operating modes:
Clip Index Screen
Playback functions are accessed from the clip index screen. To open
the clip index screen, set the camcorder to
mode.
Set the Q switch to MEDIA.
• The camcorder switches to
appears.
mode and the clip index sen
• Clips recorded at a system frequency other than the ontly
used by the camcorder, cannot be played bacplay k such
the recordings on the SD card.
5
6
1
2
3
4
7
9
8
1
2
3
4
Clip thumbnail
Recording date (month and day only) and time
Orange selection frame
5
6
7
8
9
Clip number / Total number of clips
Clip's start time code
Recording date and time
* The audio recording mode is only displayed for clips recorded using the [24 Mbps LPCM] bit rate.
Playback
Switching Between the SD Card Slots
If both SD card slots contain an SD card, you can switch between them as
necessary.
106
Operating modes:
Press the SLOT SELECT button.
• The access indicator of the selected SD card slot will illuminate in green.
Switching to Other Index Screens
The clip index screen shows AVCHD clips that were recorded on the SD
card using the camcorder. To view other recordings on the same SD card, you will need to open a different index
screen. Open the [Photos] index screen to view photos, the [SD Movies] index screen to access clips that were
converted to standard definition, or the [Shot List] index screen to vieonly shots recorded during continuous
recording.
Operating modes:
1 Press the INDEX button.
• The index screen selection menu apears.
2 Select the desired index screen and en press the jystick.
• The selected index screen appears.
• Select [Cancel] instead to cancel the operation.
• Press the INDEX button again to return to the clip index screen.
NOTES
• If you set the camcorder to
open automatically.
mode during continuous recording mode, the [Shot List] index screen will
Playback
Playing Back Clips
You can play back clips from the clip index screen. You can control the
playback with the controls on the camcorder or with the joystick and onscreen
joystick guide.
107
1 Move the orange selection frame to the clip you want to play back.
2 Press the Ò button to start playback.
• Playback will start from the clip selected and continue until the end of the
last clip in the index screen. When the last frame of the last clip is reached,
playback will be paused.
• Press the Ò button again or press the joystick to pause/resume the
playback.
• Press the Ñ button to stop the playback and return to the index screen.
IMPORTANT
• Observe the following precautions while either of the SD card access indicators is illuminated in red. Failure to
do so may result in permanent data loss.
- Do not disconnect the power source or turn off the camcorde
- Do not open the SD card compartment cover and move e SD cards.
NOTES
• You may notice brief stops in video or adio petween clips.
• Playback of clips converted to stanard definitio113) is limited to only Ð (play) and Ñ (stop). Also,
playback will stop at the end of eacclip.
Playback
Onscreen Displays
5
6
1
2
7
108
8
9
10
11
12
13
14
3
4
1
2
3
4
5
6
7
8
Recording date and time*
Playback operation
9
11 Onscreen displays superimposed on video output
14 Audio meter***
Clip number / Total number of clips
*
Appears when [£ LCD/VF Setup] > [Date/Time] is set On].
** The audio recording mode is only displayed for clips reng t[24 Mbps LPCM] bit rate.
*** Appears when [£ LCD/VF Setup] > [Audio Level] is
5 Playback operation
Ð PLAY
Playback
Ý PAUSE
Ô/Ó
F FWD ×
Ø F REV
Playback pause
Frame reverse/Frame advance
Fast playback*
Fast reverse playback*
* The playback speed (x5, x15 or x60) will also appear in the indicator.
Playback
Playback Controls
When you play back a clip, operate the buttons on the camcorder’s body or
use the joystick and joystick guide to use fast playback, play back frame-by-
frame or skip clips. Refer to the following table.
109
Available Playback Types
Playback type
Operation
Buttons: Press the Ø or × button.
Joystick: During playback, push the joystick up or down.
Repeat to increase the playback speed to approximately 5x J
15x J 60x the normal speed.
Fast playback
Frame advance/reverse
Joystick: During playback pause, push the joystick up or down.
Skip to the beginning of
the next clip
Buttons: Press the Ù button.
Joystick: Push the joystick right.
Skip to the beginning of
the current clip
Buttons: Press the Ú button.
Joystick: Push the joystick left.
Buttons: Press the Ú button twice.
Joystick: Push the joystick left twice.
Skip to the previous clip
Return to playback mode
Buttons: Press the Ò button.
Joystick: Press the joystick itself.
NOTES
• There is no audio during any of the playback tylistee previous table.
• During some special playback modes, you msoe anomalies (blocky video artifacts, banding, etc.)
in the playback picture.
• The speed indicated on the screen approxima
• You can press the DISP. button to tuthe jostick guide display on and off.
Adjusting the Volume
[¡ Audio Setup]
During playback, audio will come from the monaural built-in speaker or
headphones. When you connect headphones to the × (headphone)
terminal, the built-in speaker will be muted.
[Audio Output]
1 Open the [Headphone Volume] or [Speaker Volume] submenu.
[¡ Audio Setup] > [Audio Output] > [Headphone Volume] or
[Speaker Volume]
[Headphone Volume]
[Speaker Volume]
[8]
2 Select the desired level and then press the joystick.
• Select [Off] to mute the audio.
Playback
NOTES
• For details on changing the audio channel, refer to Selecting the
110
× (headphone)
terminal
• If you set an assignable button to [Headphone +], [Headphone -],
adjust the headphone volume or built-in speaker volume without
using the menu.
Speaker
(monaural)
Clip Operations
Clip Operations
You can use the clip menu to copy* clips, delete clips, and convert* clips to standard definition. Clip menu
functions apply only to a single clip. Selecting the same functions from the [w Other Functions] > [Clips]
submenu, you can perform the same operations on multiple clips (selected clips or all clips).
* Original AVCHD clips in the clips index screen only.
111
Operating modes:
Using the Clip Menu
1 Select a clip and then press the joystick.
• The clip menu appears.
2 Select the desired function and then press the joystick.
3 Select [OK] and then press the joystick to perform the operation.
• Select [Cancel] instead to cancel the operation.
4 When the confirmation message appears, press the joystick.
IMPORTANT
• Observe the following precautions while either of the Saccesindicators is illuminated in red. Failure to
do so may result in permanent data loss.
- Do not disconnect the power source or turcaorder.
- Do not open the SD card compartment conoemove the SD cards.
NOTES
• When performing clip operations, masure he LOCK switch on the SD cards used is not set to prevent
writing.
Copying Clips
You can copy clips from one SD card to the other.
Copying a Single Clip
1 Select the desired clip and then press the joystick to open the clip menu.
2 Select [Copy Clip] and then press the joystick.
3 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• While the clip is being copied, you can press the joystick to cancel.
4 When the confirmation message appears, press the joystick.
• The selected clip is copied to the other SD card and the screen changes back to the clip index screen.
Clip Operations
Copying a Selection of Clips
[w Other Functions]
[Clips]
1 Open the clip selection index screen.
[w Other Functions] > [Clips] > [Copy] > [Select]
112
2 Using the joystick, bring the orange selection frame to a clip you wish to
copy and then press the joystick.
[Copy]
• A checkmark " will appear next to the clip's thumbnail to indicate it
was selected. Press the joystick again to remove the checkmark.
[Select]
• Repeat this step to select all the clips you wish to copy. The total
number of selected clips will appear at the bottom of the screen, next
to the " icon.
3 After selecting all the desired clips, press the MENU button.
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to return to the clip selection screen.
• While the clips are being copied, you can press the joystick to cancel.
5 When the confirmation message appears, press the joystick.
Copying All Clips
[w Other Functions]
1 Open the [Clips Copy All] screen.
[w Other Functions] > [Clips] > [Copy] > [All]
2 Select [OK] and then press the joystick.
[Clips]
[Copy]
[All]
• All of the clips on the selected SD card will be ed to other SD
card.
• Select [Cancel] instead to cancel thoprati
• While the clips are being copied, yu can press ystick to cancel.
3 When the confirmation message appers, pres the joystick.
Deleting Clips and Shots
You can delete clips or shots you are not interested in keeping from the SD card. When you delete a shot, only
the in point/out point marks within the continuous recording clip are deleted but the video file itself is not deleted.
Although the following procedures make reference only to clips, unless stated otherwise, the procedures are the
same when deleting shots.
Deleting a Single Clip/Shot
1 Select the desired clip and then press the joystick to open the clip menu.
2 Select [Delete Clip] or [Delete Shot] and then press the joystick.
3 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• While the clip is being deleted, the operation cannot be canceled.
4 When the confirmation message appears, press the joystick.
Clip Operations
Deleting a Selection of Clips/Shots
[w Other Functions]
1 Open the clip selection or shot selection index screen.
[w Other Functions] > [Clips] > [Delete] > [Select]
[w Other Functions] > [Delete Shots] > [Select]
[Clips]
[Delete]
[Select]
113
2 Using the joystick, bring the orange selection or shot selection frame to
a clip you wish to delete and then press the joystick.
• A checkmark " will appear next to the clip's thumbnail to indicate it
was selected. Press the joystick again to remove the checkmark.
• Repeat this step to select all the clips you wish to delete. The total
number of selected clips will appear at the bottom of the screen, next
to the " icon.
[w Other Functions]
[Delete Shots]
[Select]
3 After selecting all the desired clips, press the MENU button.
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to return to the clip selection screen.
• While the clips are being deleted, you can press the joystick to
cancel.
5 When the confirmation message appears, press the joystick.
Deleting All Clips/Shots
[w Other Functions]
1 Open the [Clips Delete All] or [Delete Shots All] sc
[w Other Functions] > [Clips] > [Delete] > [
[w Other Functions] > [Delete Shots] > [A
[Clips]
[Delete]
[All]
2 Select [OK] and then press the joystk.
• All of the clips on the selected SD card will be ed.
• Select [Cancel] instead to cancel toperon.
• While the clips are being deleted, you can press the joystick to
cancel.
[w Other Functions]
[Delete Shots]
[All]
3 When the confirmation message appears, press the joystick.
Converting Clips to Standard Definition
You can convert original AVCHD clips to standard definition (MPEG-2) movies. The down-conversion to standard
definition requires two SD cards: one (source) that contains the source clips to be converted and the other one
(destination) that will store the converted files (SD movies).
Converting a Single Clip to Standard Definition
1 Select the desired clip from the index screen of the source card and then press the joystick to open the clip
menu.
2 Select [Convert HD`SD] and then press the joystick.
• The estimated size of the converted SD movie and the available space on the destination card will be
displayed on the screen.
3 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
Clip Operations
• The clip will be played back as it is converted. While the clip is being converted, you can press the joystick to
cancel.
4 When the confirmation message appears, press the joystick.
• The selected clip is converted to an SD movie on the destination card and the screen changes back to the
clip index screen.
114
Converting a Selection of Clips to Standard Definition
[w Other Functions]
1 From the index screen of the source card, open the clip selection index
screen.
[Clips]
[w Other Functions] > [Clips] > [Convert HD`SD] > [Select]
2 Using the joystick, bring the orange selection frame to a clip you wish to
convert and then press the joystick.
[Convert HD`SD]
• A checkmark " will appear next to the clip's thumbnail to indicate it
was selected. Press the joystick again to remove the checkmark.
[Select]
• Repeat this step to select all the clips you wish to convert. The total
number of selected clips will appear at the bottom of the screen, next to the " icon.
3 After selecting all the desired clips, press the MENU button.
• The estimated total size of the converted SD movies and the available space on the destination card will be
displayed on the screen.
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to return to the clip selection
• The selected clips will be played back as they conv. While the clips are being converted, you can
press the joystick to cancel.
5 When the confirmation message appersprestick.
Converting All Clips to Standard efinitn
[w Other Functions]
1 From the index screen of the source card, open the [Clips Convert
HD`SD All] screen.
[Clips]
[w Other Functions] > [Clips] > [Convert HD`SD] > [All]
• The estimated total size of the converted SD movies and the available
space on the destination card will be displayed on the screen.
[Convert HD`SD]
2 Select [OK] and then press the joystick.
[All]
• All of the clips on the source card will be converted to SD movies on
the destination card.
• Select [Cancel] instead to cancel the operation.
• The clips will be played back as they are converted. While the clips are being converted, you can press the
joystick to cancel.
3 When the confirmation message appears, press the joystick.
NOTES
• The maximum total playback time of the clips to be converted to standard definition is 12 hours.
• The bit rate of converted SD movies is 9 Mbps.
• Clips recorded with the 24P frame rate cannot be converted to standard definition.
• Clips are played back as they are converted to standard definition. If you set an assignable button to
[Headphone +], [Headphone -], [Speaker +] or [Speaker -] (A 89), you can press the button to adjust the
headphone volume or built-in speaker during the conversion.
• Clips cannot be converted to standard definition when the SD card already contains the maximum number of
Clip Operations
Deleting SD Movies
From the [SD Movies] index screen you can delete clips that were converted to standard definition.
Deleting a Single SD Movie
115
2 Select the desired SD movie and then press the joystick to open the clip menu.
3 Select [Delete Clip] and then press the joystick.
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• While the SD movie is being deleted, the operation cannot be canceled.
5 When the confirmation message appears, press the joystick.
Deleting All SD Movies
[w Other Functions]
2 Open the [Clips Delete All] screen.
[Clips]
[Delete]
[All]
[w Other Functions] > [Clips] > [Delete] > [All]
3 Select [OK] and then press the joystick.
• All the SD movies will be deleted.
• Select [Cancel] instead to cancel the operation.
• While the SD movies are being deleted, you can presoystick t
cancel.
4 When the confirmation message appears, prstic
Clip Operations
116
External Connections
6
117
Video Output Configuration
The video signal output from the HDMI OUT terminal depends on the various menu settings and the capabilities
of the external monitor. Video from the AV OUT terminal is output as 480/59.94i (59.94 Hz recordings) or 576/
50.00i (50.00 Hz recordings). If necessary, you can superimpose the onscreen displays on the video displayed
Operating modes:
Video Output Configuration by Terminal
[System Frequency]
set to [59.94 Hz]
[System Frequency]
set to [50.00 Hz]
Terminal
HD Output*
SD Output
SD Output
10809.94i
0/94P
480/594i
1080/50.00i
576/50.00P
576/50.00i
HDMI OUT
AV OUT
* You can use the [£ LCD/VF Setup] > [Zebra HD Outpetting lay the zebra patterns on an external monitor (HD
output only).
Connecting to an External Monitor
Connecting to an External Monitor
When you connect the camcorder to an external monitor for recording or playback, use the terminal on the
camcorder that matches the one you wish to use on the monitor. Then, select the video signal output
118
Operating modes:
Connection Diagram
We recommend that you power the camcorder from a household power outlet using the compact power adapter.
AV OUT
terminal
HDMI OUT
terminal
STV-250N
Stereo Video
Cable (optional)
HDMI cable
(commercially
available)
HDMI IN
VIDEO IN/
AUDIO IN
Using the HDMI OUT Terminal
The HDMITM OUT terminal offers a digital connection and outputs both a video and audio signal. The output
signal will automatically switch to HD or SD depending on the capability of the external monitor. Audio will be
output as a 2ch linear PCM (16 bits, 48 kHz) signal.
NOTES
• If necessary, you can superimpose the onscreen displays on the video displayed on the external monitor
• The HDMI OUT terminal on the camcorder is for output only. Do not connect it to an HDMI output terminal on
an external device, as this may damage the camcorder.
• There will be no video output from the AV OUT terminal while an external monitor is connected to the HDMI
OUT terminal.
• Correct operation cannot be guaranteed when connecting the camcorder to DVI monitors.
• Video may not be output correctly depending on the monitor. In such case, use the AV OUT terminal.
Connecting to an External Monitor
Using the AV OUT Terminal
The AV OUT terminal outputs a down-converted analog video signal and audio signal for connection to monitors
with a composite audio/video input.
119
NOTES
• When you play back a clip on a monitor with a 4:3 aspect ratio, the monitor will switch automatically to
widescreen mode if it is compatible with the Video ID-1 or WSS system.
• If necessary, you can superimpose the onscreen displays on the video displayed on the external monitor
SD Output
[¢ Video Setup]
When HD video (16:9 aspect ratio) is converted and output as SD video
(4:3 aspect ratio), you can choose how it appears on the external monitor.
[Resize SD Output]
[Squeeze]
Operating modes:
1 Open the [Resize SD Output] submenu.
[¢ Video Setup] > [Resize SD Output]
2 Select the desired option and then press the joysti
Options
[Letterbox]:
The 16:9 aspect ratio is maained ettebox bars are added to the top and bottom of the
image.
[Squeeze]:
The image is squeezed frm the lefand right so that the entire image fits within the screen. The image
will appear normal if the extnal nitor also has a 16:9 aspect ratio.
[Side Crop]: The left and right sides of the image are cropped so that the central part of the image fits within the
screen.
Original image (16:9)
NOTES
[Letterbox] setting
[Squeeze] setting
[Side Crop] setting
• In mode, the [Squeeze] setting is applied and cannot be changed.
Connecting to an External Monitor
Superimposing Onscreen Displays to Appear on an
External Monitor
[¢ Video Setup]
[Character Display]
[VF]
By default, onscreen displays are shown on the viewfinder but you can
choose to superimpose onscreen displays on video output from the HDMI
OUT terminal or AV OUT terminal. Doing so will display the onscreen
displays on an external monitor. You must set this function separately for
HD and SD output. This setting will not affect your recordings.
120
Operating modes:
[¢ Video Setup]
In
mode, you need to select where the onscreen displays will be
mode,
[HD Onscreen Disp.]
[SD Onscreen Disp.]
output. Perform all the procedure from the beginning. In
onscreen displays will automatically disappear from the viewfinder’s
screen when video is being output from one of the terminals, so steps 1
and 2 are not necessary. Start the procedure from step 3.
[Off]
1 Open the [Character Display] submenu.
[¢ Video Setup] > [Character Display]
2 Select [Ext. Out] and then press the joystick.
3 Open the [HD Onscreen Disp.] or [SD Onscreen Disp.] submeu.
[¢ Video Setup] > [HD Onscreen Disp.] or [SD Onscreen Di.]
4 Select [On] and then press the joystick.
• T appears on the upper right of the screen (when CD/VF Stup] > [Custom Display 2] >
[Output Display] is set to [On]).
NOTES
• Onscreen displays cannot appear siultaneously on the viewfinder and on an external monitor connected to
one of the video output terminals.
• During SD video output, onscreen displays will not appear on an external monitor if [¢ Video Setup] >
[Resize SD Output] is set to [Side Crop].
• If you set an assignable button to [Onscreen Display] (A 89), you can press the button to turn on and off the
superimposing of onscreen displays on video output from the camcorder’s terminals (simultaneously for HD
and SD video).
Audio Output
Audio Output
The camcorder can output audio from the HDMI OUT terminal, AV OUT terminal or × (headphone) terminal.
When audio is output from the AV OUT terminal or × (headphone) terminal, you can configure other settings,
such as the output channel.
121
Synchronizing the Video with the Audio being Monitored
[¡ Audio Setup]
When audio is output from the AV terminal or × (headphone) terminal,
you can choose to synchronize the audio signal with the video signal or
have the camcorder output the audio in real time. When the audio is
[Audio Output]
output in real time, there will be a slight delay. Regardless of the setting,
however, the audio and video signals recorded will be synchronized.
[Monitor Delay]
Operating modes:
[Normal]
1 Open the [Monitor Delay] submenu.
[¡ Audio Setup] > [Audio Output] > [Monitor Delay]
2 Select the desired option and then press the joystick.
Options
[Line Out]: Synchronizes the audio and video signals.
[Normal]:
Allows you to monitor the audio in rea
Selecting the Audio Channel
[¡ Audio Setup]
[Audio Output]
[Channel]
You can select the audio channel that is output from the AV OUT terminal
or × (headphone) terminal.
Operating modes:
1 Open the [Channel] submenu.
[¡ Audio Setup] > [Audio Output] > [Channel]
[CH1/CH2]
2 Select the desired option and then press the joystick.
Options
[CH1/CH2]: Audio from CH1 is output from the left audio channel and audio from CH2 is output from the right audio
channel.
[CH1/CH1]: Audio from CH1 is output from both the left and right audio channels.
[CH2/CH2]: Audio from CH2 is output from both the left and right audio channels.
[All/All]:
Audio from CH1 and CH2 is mixed and output from both the left and right audio channels.
NOTES
• If you set an assignable button to [Audio Output CH] (A 89), you can press the button to change the audio
channel directly.
Audio Output
Selecting the Output Level of the AV OUT Terminal
[¡ Audio Setup]
[Audio Output]
[Level]
You can select the output level of audio that is output from the AV OUT
terminal.
122
Operating modes:
1 Open the audio ouput [Level] submenu.
[¡ Audio Setup] > [Audio Output] > [Level]
[1 Vrms]
2 Select the desired level and then press the joystick.
Options
[1 Vrms]: The audio output level is normal.
[2 Vrms]: The audio output level is 6 dB higher.
NOTES
• This setting does not affect audio output to headphones.
Saving Clips to a Computer
Saving Clips to a Computer
Using the supplied software Data Import Utility to save your clips, you have the additional advantage of
automatically joining clips that were saved as multiple files so you can work with them as single clips with the
editing software of your choice.
123
Operating modes:
Saving Clips Using Data Import Utility:
• Save clips to the computer (all clips/new clips only).
• Join multiple video stream files of a single clip split because of the 2 GB maximum file size restriction and save
them as a single clip.
For more details, check the Data Import Utility Software Guide, a PDF file* in the [\Manual\English] folder of the
supplied PIXELA CD-ROM.
* Adobe® Reader® 6 or later is required to view the PDF file.
Installing the Software
See Installation and System requirements in the Data Import Utlity oftware Guide (PDF file) for step-by-step
installation instructions and full system requirements. Below are the in system requirements.
Windows Vista*, SP2
OS
Windows 7*, SP
Windows 8
Mac OS X 10.6, 10.7, 10.8
Intel® CPU
(not compatible with Power PC)
CPU
Intel® Core or equi
1 GB
RAM
(2 B for ndows 7/Windows 8, 64-bit version or Mac OS X 10.7/10.8)
Display
1024 x 768 pixels
* 32-bit and 64-bit versions.
Connection Diagram
We recommend that you power the camcorder from a household power outlet using the compact power adapter.
USB terminal
(mini-B)
USB terminal
(standard-A)
IFC-400PCU USB Cable
(optional)
Saving Clips to a Computer
124
Photos
7
125
Taking Photos
You can take photos when the camcorder is in
mode or you can capture a photo from a clip when the
camcorder is in
mode. The size of the photos recorded on the SD card is 1920 x 1080*.
* At this size, the camcorder can save approximately 670 photos on a 1 GB SD card.
Taking Photos in CAMERA Mode
You can take a photo while the camcorder is recording a clip or is in record pause mode. If a custom picture file
is selected in advance, it will be recorded with the photo (A 92). To take a photo, set an assignable button to
[Photo] in advance.
Operating modes:
2 Press the assignable button to take a photo.
• The icon of the selected SD card (2 or 3) and the of avable photos appear momentarily on the
upper right of the screen.
• If a custom picture file is selected, it will be witthe photo.
• The SD card access indicator will umnate the photo is being recorded.
Capturing Photos in MEDIA Mode
You can capture a photo from a clip during playback pause. To capture a photo, set an assignable button to
[Photo] in advance.
Operating modes:
2 Select the desired clip and press the Ò button to start playback.
3 Pause the playback at the point you want to capture.
4 Press the assignable button to capture a photo.
• The screen will momentarily turn black as if a camera shutter had released.
• The icon of the selected SD card (2 or 3) and the number of available photos appear momentarily on the
upper right of the screen.
• The SD card access indicator will illuminate in red as the photo is being recorded.
5 Press the Ñ button to stop playback.
IMPORTANT
• Observe the following precautions while either of the SD card access indicators is illuminated in red. Failure to
do so may result in permanent data loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not open the SD card compartment cover and do not remove the SD cards.
Taking Photos
NOTES
• If the LOCK switch on the SD card selected for recording is set to prevent writing, you will not be able to
record a photo. Change the position of the LOCK switch in advance.
• Even if [w Other Functions] > [Custom Function] > [Scan Reverse Rec] (A 102) is set to a setting other
than [Off], photos will not be inverted.
126
Photo Playback
Photo Playback
You can view the photos that you took with the camcorder.
Operating modes:
127
Displaying the [Photos] Index Screen
Display the [Photos] index screen to view photos.
1 Set the Q switch to MEDIA.
• The camcorder switches to
screen appears.
mode and the clip index
2 Press the INDEX button.
• The index screen selection menu appears.
3 Select [Photos] and then press the joystick.
• The [Photos] index screen appears.
• After you are finished viewing photos, press the INDEX button to
return to the clip index screen.
Viewing Photos
1 Move the orange selection framto the deoto.
2 Press the Ò button to view thphoto
• The photo playback screen appears he selected photo is displayed.
• Use the Ú/Ù buttons or push the joystick left/right to switch to the
previous/next photo.
• Press the DISP. button to hide/show the onscreen displays.
• Press the Ñ button to return to the [Photos] index screen.
IMPORTANT
• Observe the following precautions while either of the SD card access
indicators is illuminated in red. Failure to do so may result in permanent data
loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not open the SD card compartment cover and do not remove the SD
cards.
NOTES
• The following photos may not be displayed correctly.
- Photos not recorded with this camcorder.
- Photos created or edited on a computer.
- Photos whose file names have been changed.
Photo Operations
Photo Operations
You can use the photo menu to copy a photo, delete a photo, or copy a custom picture file embedded in a
photo. You can display the photo menu from the [Photos] index screen or photo playback screen.
128
Using the Photo Menu
1 From the [Photos] index screen, select a photo and then press the joystick.
• If you are viewing a photo, simply press the joystick.
• The photo menu appears. Available functions depend on the photo’s settings.
2 Select the desired function and then press the joystick.
Copying Photos
You can copy photos from one SD card to the other.
Operating modes:
Copying a Photo from the Playback Screen
2 Press the joystick to open the photo menu.
3 Select [Copy] and then press the joysck
4 Select [OK] and then press the joystk.
• Select [Cancel] instead to cancel thoperan.
• The selected photo is copied.
5 When the confirmation message appears, press the joystick.
Copying a Photo from the Index Screen
2 Move the orange selection frame to the photo to be copied.
3 Press the joystick to open the photo menu.
4 Select [Copy] and then press the joystick.
5 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• The selected photo is copied.
6 When the confirmation message appears, press the joystick.
Photo Operations
Copying a Selection of Photos
[w Other Functions]
1 From the [Photos] index screen open the photo selection screen.
[w Other Functions] > [Photos] > [Copy] > [Select]
[Photos]
[Copy]
129
2 Using the joystick, bring the orange selection frame to a photo you wish
to copy and then press the joystick.
• A checkmark " will appear next to the photo's thumbnail to indicate
it was selected. Press the joystick again to remove the checkmark.
[Select]
• Repeat this step to select all the photos you wish to copy. The total
number of selected photos will appear at the bottom of the screen,
next to the " icon.
3 After selecting all the desired photos, press the MENU button.
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to return to the photo selection screen.
• While the photos are being copied, you can press the joystick to cancel.
5 When the confirmation message appears, press the joystick.
Copying All Photos
[w Other Functions]
1 From the [Photos] index screen open the [Photos Copy All] scren.
[w Other Functions] > [Photos] > [Copy] > [All]
2 Select [OK] and then press the joystick.
[Photos]
[Copy]
[All]
• Select [Cancel] instead to cancel the operat
• While the photos are being copied, you cae jostick to
cancel.
3 When the confirmation message apears, press oystick.
Deleting Photos
You can delete a photo you no longer need. When you do so, however, the custom picture file embedded in it
will also be deleted. Photos can be deleted one at a time from the photo playback screen or [Photos] index
screen.
Operating modes:
Deleting a Photo from the Playback Screen
2 Press the joystick to open the photo menu.
3 Select [Delete] and then press the joystick.
4 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• The selected photo is deleted and the next photo is displayed.
• If a custom picture file is embedded in the photo, it is also deleted.
5 When the confirmation message appears, press the joystick.
Photo Operations
Deleting a Photo from the Index Screen
2 Move the orange selection frame to the photo to be deleted.
3 Press the joystick to open the photo menu.
130
4 Select [Delete] and then press the joystick.
5 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
• The selected photo is deleted.
• If a custom picture file is embedded in the photo, it is also deleted.
6 When the confirmation message appears, press the joystick.
Deleting a Selection of Photos
[w Other Functions]
[Photos]
1 From the [Photos] index screen open the photo selection screen.
[w Other Functions] > [Photos] > [Delete] > [Select]
2 Using the joystick, bring the orange selection frame to a photo you wish
to delete and then press the joystick.
[Delete]
• A checkmark " will appear next to the photo's thumbnail to indicte
it was selected. Press the joystick again to remove the checkmar
[Select]
• Repeat this step to select all the photos you wish to delete. The al
number of selected photos will appear at the bottom creen
next to the " icon.
3 After selecting all the desired photos, press thbutn.
4 Select [OK] and then press the joystic.
• Select [Cancel] instead to return to he photo sn screen.
• While the photos are being deleted, ou capress the joystick to cancel.
5 When the confirmation message appears, press the joystick.
Deleting All Photos
[w Other Functions]
[Photos]
1 From the [Photos] index screen open the [Photos Delete All] screen.
[w Other Functions] > [Photos] > [Delete] > [All]
2 Select [OK] and then press the joystick.
• Select [Cancel] instead to cancel the operation.
[Delete]
• While the photos are being deleted, you can press the joystick to
cancel.
[All]
3 When the confirmation message appears, press the joystick.
IMPORTANT
• Be careful when deleting photos. Deleted photos cannot be recovered.
• Photos that were protected using other devices cannot be deleted with the camcorder.
Photo Operations
Copying Custom Picture Files
You can copy to the camcorder a custom picture file embedded in a photo. Custom picture files can be copied
from the photo playback screen or [Photos] index screen.
131
Operating modes:
Copying a File from the Playback Screen
2 Press the joystick to open the photo menu.
3 Select [Copy / File] and then press the joystick.
• The [/ Data 1/3] screen appears with a file slot in the camcorder highlighted in orange.
• Alternatively, you can press the CUSTOM PICTURE button.
• You can push the joystick up/down to display the [/ Data 2/3] and [/ Data 3/3] screens.
4 Push the joystick left/right to select the desired file slot and then press the joystick.
5 Select [OK] and then press the joystick.
• The custom picture file embedded in the selected photo is copied, overwriting the file in that slot.
• Select [Cancel] instead to cancel the operation.
6 When the confirmation message appears, press the joystick.
Copying a File from the Index Screen
2 Move the orange selection frame to the photcusm picture file to be copied.
3 Press the joystick to open the photmenu.
4 Select [Copy / File] and then presthe joysick.
• The [/ Data 1/3] screen appears wh thorange selection frame indicating a file slot in the camcorder.
• Alternatively, you can press the CUSTOM PICTURE button.
• You can push the joystick up/down to display the [/ Data 2/3] and [/ Data 3/3] screens.
5 Push the joystick left/right to select the desired file slot and then press the joystick.
6 Select [OK] and then press the joystick.
• The custom picture file embedded in the selected photo is copied, overwriting the file in that slot.
• Select [Cancel] instead to cancel the operation.
7 When the confirmation message appears, press the joystick.
NOTES
• You cannot copy the custom picture file to a file slot with a protected file.
• By default, file slots [C7] to [C9] are protected.
Photo Operations
132
Additional Information
8
133
Menu Options
For details about how to select an item, refer to Using the Menus (A 27). For details about each function, see
the reference page. Menu items without a reference page are explained after the tables. Setting options in
boldface indicate default values. Menu items not available appear grayed out.
To skip directly to the page of a specific menu:
[~ Camera Setup] menu
[¡ Audio Setup] menu
[¢ Video Setup] menu
[£ LCD/VF Setup] menu
[¤ TC/UB Setup] menu
[w Other Functions] menu
A 133
A 134
A 134
A 135
A 138
A 138
A 140
[
My Menu] customized menu
[~ Camera Setup] menu (
mode only)
Menu item
[Light Metering]
[AE Shift]
Submenu
Setting options
A
[Backligard], [Stlight]
[.0], [+.25], [+1.0, [+0.75], [+0.5], [+0.25], [ 0], [-0.25],
0.75-1.0], [-1.25], [-1.5], [-2.0]
[ISO/Gain]
[Select]
n]
[Extended Rang
[ISO Increment]
[Gain]
[1 stop], [1/3 stop]
[Normal], [Fine]
[Automatic], [Manual]
[1/2 stop], [1/3 stop], [Fine]
[On], [Off]
[Iris]
[Mode]*
[Iris Increment]
[Zoom-Iris Correct.]
[Mode]
[Shutter]
[Speed], [Angle], [Clear Scan], [Slow], [Off]
[1/3 stop], [1/4 stop]
[One Shot], [Continu.]
[Automatic], [Off]
[On], [Off]
[Shutter Increment]
[AF Mode]*
[Flicker Reduction]
[/ CINEMA Locked]
[EF-S Lens]
[On], [Off]
[ABB]
[Cancel], [OK]
[Color Bars]
[Enable]
[Type]
[On], [Off]
When [System Frequency] is set to [59.94 Hz]:
[SMPTE], [ARIB]
When [System Frequency] is set to [50.00 Hz]:
[EBU], [SMPTE]
[Periph. Illum. Corr.]
[On], [Off]
* Available only when an EF-S 18-135mm f/3.5-5.6 IS STM or EF-S 18-55mm f/3.5-5.6 IS STM lens is attached.
Menu Options
[¡ Audio Setup] menu
Menu item
Submenu
[Int. Mic Low Cut]
[Int. Mic Sensitivity]
[MIC/Int. Mic Att.]
[MIC Mode]
Setting options
[Off], [LC1], [LC2]
A
[Audio Input]
Ü
Ü
Ü
Ü
Ü
Ü
–
–
–
–
–
–
[Normal], [High]
134
[On], [Off]
[Automatic], [Manual]
0 to 99 (50)
[MIC Level]
[XLR Rec Channel]
[XLR1 Mic Trimming]
[XLR2 Mic Trimming]
[XLR1 Mic Att.]
[XLR2 Mic Att.]
[XLR ALC Link]
[Limiter]
[CH1], [CH1/CH2]
[+12 dB], [+6 dB], [0 dB], [-6 dB], [-12 dB]
Ü
Ü
–
–
[On], [Off]
[Linked], [Separated]
Ü
Ü
–
–
[On], [Off]
75,
[1 kHz Tone]
[Monitor Delay]
[Channel]
[-12 dB], [-18 dB], [-20 dB], [Off]
[Line Out], [Normal]
Ü
Ü
Ü
Ü
–
–
[Audio Output]*
[CH1/CH2], [CH1/CH1], [C2/CH2], [All/All]
[1 Vrms], [2 Vrms]
Ü
Ü
[Level]
[Headphone Volume]
[Off], 1 to 1
79,
Ü
Ü
Ü
[Speaker Volume]
o 15
–
* Not available in the [Photos] index screen.
[¢ Video Setup] menu
Menu item
Setting options
A
[Character Display]
[HD Onscreen Disp.]
[SD Onscreen Disp.]
[Resize SD Output]
[VF], [Ext. Out]
[On], [Off]
Ü
Ü
Ü
–
–
Ü
Ü
Ü
[On], [Off]
[Letterbox], [Squeeze], [Side Crop]
Menu Options
[£ LCD/VF Setup] menu
Menu item
Submenu
[Brightness]
Setting options
A
[LCD Setup]
-99 to 99 ( 0)
-99 to 99 ( 0)
-20 to 20 ( 0)
1 to 4 (2)
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
[Contrast]
[Color]
135
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
–
[Sharpness]
[Backlight]
[Brightness]
[Contrast]
[Color]
[Normal], [Bright]
-99 to 99 ( 0)
[VF Setup]
-99 to 99 ( 0)
-20 to 20 ( 0)
[Sharpness]
[Backlight]
1 to 4 (2)
[Normal], [Bright]
[On], [Off]
[LCD/VF B&W]
[LCD/VF Simul.]
[View Assist.]
[Peaking]
[On], [Off]
[On], [Off]
[On], [Off]
–
[Select]
[Peaking 1], [Peaking 2]
[White], [Red], [Yellow], ue]
[Off], 1 to 15 (8)
1 to 4 (2
–
[Peaking 1]
[Color]
–
[Gain]
–
[Frequency]
[Color]
–
[Peaking 2]
[White], [Rlow], [Blu
o 15 5)
–
[Gain]
–
[Frequency]
–
[Zebra]
–
[Select]
[Zebra 1], [Zebra 2], [Zebra 1&2]
–
[Zebra 1 Level]
[70 5%], [75 5%], [80 5%], [85 5%],
[90 5%], [95 5%]
Ü
Ü
–
–
[Zebra 2 Level]
[70%], [75%], [80%], [85%], [90%], [95%],
[100%]
[Zebra HD Output]
[Markers]
[On], [Off]
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
–
–
–
–
–
–
–
–
[Enable]
[On], [Off]
[Center]
[White], [Gray], [Off]
[White], [Gray], [Off]
[White], [Gray], [Off]
[White], [Gray], [Off]
[80%], [90%], [92.5%], [95%]
[White], [Gray], [Off]
[Horizontal]
[Grid]
[Safety Zone]
[Safety Zone Area]
[Aspect Marker]
[Aspect Ratio]
[4:3], [13:9], [14:9], [1.66:1], [1.75:1],
[1.85:1], [2.35:1]
Ü
–
[Audio Level]
[On], [Off]
–
Ü*
–
Menu Options
Menu item
Submenu
[Light Metering]
Setting options
A
[Custom Display 1]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
Ü
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Ü*
–
[Custom Picture]
[Focal Length]
[ND Filter]
136
[AF Mode]
[Key Lock]
[White Balance]
[Exposure]
[Iris]
[ISO/Gain]
[Shutter]
[Peaking]
[Magnification]
[View Assist.]
[EF-S Lens]
[Lens]
[Custom Display 2]
[Remaining Battery]
[Remaining Rec Time]
[Rec Mode]
[Warning], [Normal], [Off
[Warning], [Normal], f]
[On], [Off]
–
[Time Code]
[Photo]
[On], [Off]
[Noal], [Off]
[Bit Rate]
[Frame Rate]
[Character Rec]
[Output Display]
[User Bit]
[
[On], [Off]
[On], [Off]
[On], [Off]
[Audio Output CH]
[Audio Level]
[HDMI Rec Command]
[Temperature/Fan]
[Date/Time]
[On], [Off]
[On], [Off]
[On], [Off]
[On], [Off]
[Date/Time], [Time], [Date], [Off]
[On], [Off]
[Date/Time]
* Not available in the [Photos] index screen.
–
[Audio Level]: Displays the audio level meter when set to [On].
[Custom Display 1] settings
[Light Metering]: When set to [On], the light metering icon (° or ®) is displayed if [~ Camera Setup] >
[Light Metering] is set to [Backlight] or [Spotlight].
[Custom Picture]: Displays the custom picture icon (/) when set to [On], indicating that a custom picture file
was selected and its custom picture settings will be applied.
[Focal Length]: Displays the current focal length of an attached EF lens when set to [On].
[ND Filter]: Displays the ND filter indicator when set to [On].
[AF Mode]: When set to [On], displays the autofocus icon (AF) if the focus mode switch on the attached EF lens
is set to AF.
[Key Lock]: Displays the key lock icon (C) when set to [On].
Menu Options
[White Balance]: Displays the white balance indicator when set to [On].
[Exposure]: Displays the exposure bar when set to [On].
[Iris]: Displays the aperture setting when set to [On].
137
[ISO/Gain]: Displays the ISO speed or gain setting when set to [On].
[Shutter]: Displays the shutter speed setting when set to [On].
[Peaking]: Displays the peaking icon (J or K) when set to [On].
[Magnification]: Displays the screen magnification icon (^) when set to [On], indicating that the image on
the screen is being magnified.
[View Assist.]: Displays the view assistance icon (
) when set to [On].
when set to [On].
[EF-S Lens]: Displays the EF-S lens correction icon
[Lens]: Displays the lens warning icon
when set to [On].
[Custom Display 2] settings
[Remaining Battery]: Controls when the remaining battery indicator appears.
[Normal]: Always appears on the screen.
[Warning]: Appears only when there is a warning.
[Remaining Rec Time]: Displays the remaining recording time.
[Normal]: Always appears on the screen.
[Warning]: Appears only when there is a warning.
[Rec Mode]: Displays the recording operation indicator in recd pause mode, for example) when set
to [On].
[Time Code]: Displays the time code when se
[Photo]: Controls the display of the D card staator and remaining number of photos when taking a
photo.
[Normal]: Always appears on the scren.
[Warning]: Appears only when there is a warning.
[Bit rate]: Displays the bit rate when set to [On].
[Frame Rate]: Displays the frame rate when set to [On].
[Character Rec]: Displays the character recording warning icon (S) when set to [On], indicating that the
onscreen displays will be recorded on the clip.
[Output Display]: Displays the output display warning icon (T) when set to [On], indicating that the
onscreen displays will be output to an external monitor.
[User Bit]: Displays the user bit when set to [On].
[Audio Output CH]: Displays the audio output channel when set to [On].
[Audio Level]: Displays the audio level indicator and, if activated, the audio peak limiter icon ( ) when set to [On].
[HDMI Rec Command]: Displays the status of the HDMI recording command that is being output when
[w Other Functions] > [HDMI] > [Rec Command] is set to [On].
[Temperature/Fan]: Displays the cooling system warning icons ( and/or
[Date/Time]: Displays the date and/or the time while recording.
[Date/Time]: Displays the date and time of recording during playback.
) when set to [On].
Menu Options
[¤ TC/UB Setup] menu (
mode only)
Menu item
Submenu
Setting options
A
[Time Code]
[Mode]
[Preset], [Regen.]
[Rec Run], [Free Run]
[DF], [NDF]
[Run]
138
[DF/NDF]*
[Setting]
[Set], [Reset]
[User Bit]
[Output Mode]
[Type]
[Fixed], [Pulldown]
[Setting], [Time], [Date]
* In the following cases, the time code is set to [NDF] and this setting cannot be changed:
- [w Other Functions] > [System Frequency] is set to [50.00 Hz]
- [w Other Functions] > [System Frequency] is set to [59.94 Hz] and the frame rate is set to 24P
[w Other Functions] menu
Menu item
Submenu
[All Settings]
Setting options
A
[Reset]
[Cancel], [OK]
[Cancel], [OK]
[Cancel], [OK]
Ü
Ü
Ü
Ü
–
[Camera Settings]
[Assignable Buttons]
[Save To *]
–
1
Ü
[Transfer Menu//]
[*A] [Menu], [Menu+/]
[*B]
Ü
Ü
Ü
Ü
[Load From *]
[*A] [Menu], [Men/]
[*B]
[Time Zone]
[Set Clock]
orld zones.
0 NeYork] or
Cenral Europe]
Ü
Ü
2
[Date/Time]
–
Ü
Ü
Ü
Ü
[Date Format]
[YMD], [YMD/24H], [MDY], [MDY/24H],
2
[DMY], [DMY/24H]
[WFM (LCD)]
[Setting]
[WFM], [Edge Mon.], [Off]
[WFM], [Off]
Ü
–
–
Ü
Ü
Ü
–
4
4
4
[Waveform Monitor]
[Gain]
[Line], [Line+Spot], [Field], [RGB], [YPbPr]
[1x], [2x]
Ü
Ü
Ü
Ü
[Edge Monitor]
[Gain]
[Type 1], [Type 2]
[Off], 1 to 15 (12)
–
[Language !]
[Deutsch], [English], [Español], [Français],
[Italiano], [Polski], [
], [
], [
],
Ü
Ü
[
]
[REMOTE Term.]
[Assign Button]
[RC-V100], [Standard]
Ü
Ü
–
Ü
–
[1] to [15]
[7] to [15]
[Front]
See footnote 3
1
1
Ü
[Tally Lamp]
[On], [Off]
Ü
–
–
[Rear]
[Media Access LED]
[Fan]
[On], [Off]
Ü
Ü
Ü
Ü
Ü
Ü
–
–
[On], [Automatic]
2
[System Frequency]
[Relay Rec]
[59.94 Hz], [50.00 Hz]
[On], [Off]
Ü
–
[Double Slot Rec]
[Continuous Rec]
[On], [Off]
–
[Mode]
[On], [Off]
Ü
–
[Start/Stop]
[Start], [Stop]
Menu Options
Menu item
Submenu
Setting options
A
[Bit Rate]
[24 Mbps LPCM], [24 Mbps], [17 Mbps],
[7 Mbps]
Ü
Ü
–
–
[Frame Rate]
When [System Frequency] is set to [59.94 Hz]:
[60i], [PF30], [PF24], [24P]
When [System Frequency] is set to [50.00 Hz]:
[50i], [PF25]
139
[Pre Rec]
[On], [Off]
Ü
Ü
–
–
–
–
[Delete Last Clip]
[Clips]
[Cancel], [OK]
4
4
5
4
6
[Copy]
[Select], [All]
Ü
Ü
Ü
Ü
Ü
–
[Delete]
[Select], [All]
–
[All]
–
[Convert HD`SD]
[Select], [All]
–
[Delete Shots]
[Rec Review]
[HDMI]
[Select], [All]
–
[Entire Clip], [Last 4 sec]
[On], [Off]
Ü
Ü
Ü
Ü
Ü
–
[Time Code]
[Rec Command]
[File Numbering]
[Add / File]
[Copy]
–
–
[On], [Off]
–
–
[Photos]
[Reset], [Continu.]
[On], [Off]
–
–
7
7
1
[Select], [All]
Ü
Ü
Ü
[Delete]
[Select]
–
[File Numbering]
[et], [C]
]
–
[Custom Function]
[Shockless WB]
[AE Response]
rmal], [Slow]
[, [Normal]
[Both], [Magnify], [Peaking], [Off]
[Peaking], [Edge Mon.], [Off]
[Both], [Vertical], [Horizontal], [Off]
[On], [Off]
[Grip Ctrl Dial Di
[F. Assist. B&W]
[Magn. Add. Disp.]
[Scan Reverse Rec]
[Character Rec]
[C START/STOP]
Ü
–
[On], [Off]
[Reset Hour Meter]
[Initialize Media]
[Cancel], [OK]
Ü
Ü
Ü
Ü
–
[*A]
[Complete], [Quick]
[*B]
[Lens Firmware]
[Firmware]
–
–
Ü
Ü
–
–
–
1
2
3
Not available in the [Photos] index screen.
The default value depends on the country/region or purchase.
Setting options for [Assign Button]: [(NONE)], [ONE-SHOT AF], [PUSH AUTO IRIS], [Iris Mode], [Iris +], [Iris -], [AE Shift +],
[AE Shift -], [Backlight], [Spotlight], [ISO/GAIN], [SHUTTER], [View Assist.], [PEAKING], [ZEBRA], [WFM], [MAGN.], [Color Bars],
[Markers], [LCD Setup], [VF Setup], [LCD/VF B&W], [Onscreen Display], [Time Code], [Time Code Hold], [Headphone +],
[Headphone -], [Speaker +], [Speaker -], [Audio Output CH], [Audio Level], [Photo], [Fan], [My Menu], [Initialize Media], [
Down], [ Left], [ Right], [ SET], [User Setting (NONE)].
Up],
[
The default settings are as follows. [1] to [6]: [(NONE)], [7] and [8]: [MAGN.], [9]: [PEAKING], [10]: [ZEBRA], [11]: [WFM], [12]:
[PUSH AUTO IRIS], [13]: [ISO/GAIN], [14]: [SHUTTER], [15]: [ONE-SHOT AF]
Available in the clip index screen only.
Available in the [SD Movies] index screen only.
Available in the [Shot List] index screen only.
4
5
6
7
Available in the [Photos] index screen only.
[Reset]: Reset various camcorder settings.
[All Settings]: Resets all the camcorder’s settings to default settings, except for the hour meter.
Menu Options
[Camera Settings]: Resets the white balance, iris, ISO speed, gain, shutter speed, [~ Camera Setup]
settings and custom picture settings to default settings.
[Assignable Buttons]: Resets the assignable buttons to default settings.
[Tally Lamp]: Allows you to set whether the front and rear tally lamps illuminate while the camcorder is recording.
140
[Media Access LED]: Allows you to set whether the respective SD card access indicator illuminates while the
camcorder is accessing an SD card.
[Delete Last Clip]: Deletes the last clip you recorded. This menu option will not be available if you turned the
camcorder off since recording the last clip.
[HDMI] settings
[Time Code]: Allows you to output the internal camcorder-generated time code through the HDMI OUT
terminal. The setting cannot be changed while the camcorder is connected to an external device using an
HDMI cable (commercially available).
[Rec Command]: After selecting to output the time code, this setting allows you to additionally output also the
camcorder’s recording command. When you connect the camcorder to another recording device using the
HDMI OUT terminal, if you start or stop recording with the camcorder, the other device will also start or stop
recording. The setting cannot be changed while the camcorder is connected to an external device using an
HDMI cable (commercially available).
[Reset Hour Meter]: The camcorder has two “hour meters” – the first keeps track of total operation time and the
second keeps track of operation time since the last time the second hur meter was reset with this function.
[Firmware]: You can verify the current version of the camcordes firmw. This menu option is usually unavailable.
[
My Menu] (
mode only)
Menu item
Submenu
Setting options
A
[Edit]
[Register]
[Move]
ncel][OK]
ncel], [OK]
[Cancel], [OK]
[Cancel], [OK]
[Delete]
[Reset All]
Displaying the Status Screens
Displaying the Status Screens
You can use the status screens to check the camcorder’s various recording- and playback-related settings. You
can also output the status screens on an external monitor.
141
Operating modes:
1 Press the STATUS button.
• The status screen most recently displayed will appear unless you
turned off the camcorder or changed the operating mode. In such
case, the [Camera] status screen appears in
[Assign Button 1/2] status screen appears in
mode and the
mode.
2 Push the joystick up/down to scroll through the status screens.
3 When you are finished, press the STATUS button again to exit the
status screens.
• Alternatively, you can press the MENU or CUSTOM PICTURE button.
Doing so will exit the status screen and open the respective menu.
,
Status screen
Descrip
A
[Camera]
Displays settings related to ding, s ISO speed/gain, iris
and shutter speed increheral umination correction and
attached lens model info
Ü
Ü
–
[Assign Button 1/2],
[Assign Button 2/2]
Allows you terify the curreion of each assignable button.
Ü
1
[Audio]
[Media]
[Video]
Displays settingelateo audio.
Ü
Ü
Ü
Ü
Displays information about the SD cards.
Displays the settings for the video terminals and whether the pre-
recording mode is in effect.
Ü
Ü
Ü
Ü
Ü
–
[Battery/Hour Meter]
Allows you to check the remaining battery time, battery life and how
long the camcorder has been in operation.
[/ Data 1/3], [/ Data 2/3],
[/ Data 3/3]
Displays the settings for the custom picture file that is in effect.
2
1
2
Does not appear in the [Photos] index screen.
These screens appear only after a custom picture file has been selected.
Displaying the Status Screens
[Audio] Status Screen
In
mode
143
1
2
3
4
5
6
7
8
9
10
11
12
13
In
mode
8
14
1
2
Low-cut filter (built-in microphone) (
Microphone's sensitivity (built-in microphone)
A
76)
7
8
9
3
Microphone attenuator (MIC terminal, built-in
4
5
6
[Media] Status Screen
In
mode
3
4
5
6
7
8
9
1
2
10
1
2
3
4
5
SD card A
SD card B
SD speed class (
Total space on the card
Used space on the card
6
7
8
9
Clip recording time* (
Total shot recording time* (
Available recording time on the card**
Available number of photos on the card**
A
85)
A
85)
A
38)
10 Approximate used space on the card
* This information appears only during continuous recording mode.
**In mode, this information appears only when opening the status screen from the clip index screen.
NOTES
• Depending on the card used, the total space displayed on the screen may differ from the nominal capacity
listed on the SD card.
Displaying the Status Screens
• In
mode and when both relay recording and double slot recording mode are turned off in
mode,
only the information about the SD card currently selected for recording/playback will be displayed.
144
[Video] Status Screen
1
2
3
5
4
1
2
HDMI OUT terminal status
Onscreen displays superimposed on HD video
4
5
Onscreen displays superimposed on SD video
3
*
mode only.
[Battery/Hour Meter] Status Screen
1
2
3
4
5
1
2
3
Remaining recording time
Remaining recording time indicator
Battery life indicator
4
5
Operation time since using [Reset Hour Meter]
Displaying the Status Screens
[/ Data 1/3] Status Screen (
mode only)
1
2
3
4
5
6
7
8
145
9
1
2
3
4
5
Black gamma settings (level, range and point)
6
7
8
9
Knee settings (slope, point and saturation)
Skin detail settings (hue, chroma, area and Y
Selective NR settings (hue, chroma, area and Y
[/ Data 2/3] Status Screen (
mode onl
1
2
3
4
5
6
7
1
Sharpness settings (level, horizontal detail
frequency, horizontal/vertical detail balance, and
Sharpness settings (select, knee aperture gain
4
Coring settings (level, offset, curve and depth)
Color matrix settings (select, gain and phase)
5
6
2
3
Level depend settings (level, slope and offset)
7
Resetting the File Numbering
Resetting the File Numbering
mode:
Photos and SD movies are automatically assigned consecutive numbers
from 0101 to 9900, and stored on the SD card in folders containing up to
100 files. Folders are numbered from 101 to 998. You can select the file
numbering method to be used but using the default [Continu.] setting is
recommended.
[w Other Functions]
[Photos]
147
[File Numbering]
[Continu.]
Operating modes:
1 Open the [File Numbering] submenu.
mode: [w Other Functions] > [Photos] > [File Numbering]
mode: [w Other Functions] > [File Numbering]
2 Select the desired option and then press the joystick.
mode:
[w Other Functions]
[File Numbering]
[Continu.]
Options
[Reset]:
File numbers will restart from 101-01time ou insert a new SD card. If an SD card already
contains photos or SD movies, file nuconnue from the number following that of the last photo
or SD movie on the SD ca.
[Continu.]: File numbers will continue fm the number following that of the last photo recorded or SD movie
converted with the camcordeHowver, if the SD card you insert already contains photos or SD movies,
file numbers will continue from the number following that of the last photo or SD movie on the SD card.
This setting is the most convenient for managing files on a computer.
NOTES
• The file number indicates the name and location of the file on the SD card. For example, the file of a photo
numbered 101-0107 is "IMG_0107.jpg" and it can be found in the "DCIM\101CANON" folder, while the file of
an SD movie numbered 101-0108 is "MVI_0108.mpg"and it is stored in the same folder.
Troubleshooting
Troubleshooting
If you have a problem with your camcorder, refer to this section. Consult your dealer or a Canon Service Center
if the problem persists.
148
Power source
The camcorder will not turn on or it turns off by itself.
- The battery pack is exhausted. Replace or charge the battery pack.
- Remove the battery pack and reattach it correctly.
Shortly after turning it on, the camcorder turns off on its own.
- You are using a battery pack that is not compatible for use with this camcorder. Use a recommended battery pack
Cannot charge the battery pack.
- The temperature of the battery pack is outside the charging range. If the battery pack’s temperature is below 0 °C
(32 °F), warm it before charging it; if it is above 40 °C (104 °F), let the battery pack cool down before charging it.
- Charge the battery pack in temperatures between 0 °C and 40 °C (32 °F and 104 °F).
- The battery pack is faulty. Replace the battery pack.
The battery pack is exhausted extremely quickly even at normal temperatures.
- Check the [Battery/Hour Meter] status screen (A 144) to see whether thbattery pack is at the end of its service life.
If so, buy a new battery pack.
Recording
The camcorder’s controls are not responsive/disab
- The grip unit’s plug may not be correctconnecteamcorder. When attaching the grip unit to the camcorder,
make sure the grip unit’s plug is firmly serted all thnto the connection terminal on the camcorder (A 35). If
you changed the angle of the grip unit, ake suryou did not partially disconnect the plug by mistake.
- When the Q switch is set to C, all ttons xcept for the START/STOP button are locked and cannot be
operated. (Depending on the [Other Function> [Custom Function] > [C START/STOP] setting, the START/STOP
button may be locked as well.) Set the Q switch to CAMERA.
Pressing the START/STOP button will not start recording.
- The SD card is full or it already contains the maximum number of clips (3,999 clips). Delete some clips (A 112) or
save your clips (A 123) and initialize the SD card (A 40) to free some space. Alternatively, replace the SD card.
- The START/STOP lock lever on the handle unit is set to C, rendering the handle unit's START/STOP button
inoperable. Change the position of the lock lever.
The point where the START/STOP button was pressed does not match the beginning/end of the recording.
- There is a slight interval between pressing the START/STOP button and the actual start/end of recording. This is not a
malfunction.
The camcorder will not focus.
- The viewfinder is not adjusted. Use the dioptric adjustment lever to make the proper adjustment (A 33).
- The lens is dirty. Clean the lens with a soft lens-cleaning cloth.
When a subject flits across in front of the lens, the image appears slightly bent.
- This is a phenomenon typical of CMOS image sensors. When a subject crosses very quickly in front of the camcorder,
the image may seem slightly warped. This is not a malfunction.
Bright red, green or blue dots appear on the screen.
- The camcorder’s CMOS sensor is a delicate piece of precision engineering. Direct exposure of the sensor to ion rays or other
types of cosmic radiation may affect it and this may rarely appear as bright colored dots on the screen. This is the nature of
CMOS image sensors and does not represent a malfunction. Adjusting the black balance (A 43) may help solve the problem.
- The effects of the damage may be more noticeable when the camcorder is used in places subject to high
temperatures, when a high ISO speed or gain level is used and when slow shutter speeds are used.
Abnormal images appear on the screen and the camcorder cannot record properly.
- While recording using an almost empty battery pack together with the compact power adapter, the compact power
adapter was inadvertently disconnected or the power supply was suddenly interrupted. Reconnect the compact
power adapter and turn the camcorder off and then on again or replace the battery pack with a fully charged one.
Troubleshooting
Changing between recording (ÜREC) and record pause (STBY) takes longer than usual.
- When the SD card contains a large number of clips, some operations may take longer than usual. Save your clips
The camcorder cannot record to an SD card properly.
- This may occur as recordings are made and deleted over time. Save your clips (A 123) and initialize the SD card (A 40).
149
After using the camcorder for a long time, it becomes hot.
- The camcorder may become hot after using it continuously for long periods of time; this is not a malfunction. If the
camcorder becomes unusually hot or it becomes hot after using it only for a short while, it may indicate a problem with
the camcorder. Consult a Canon Service Center.
Playback
Cannot delete clips or photos.
- Clips and photos that were protected using other devices cannot be deleted with the camcorder.
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
Deleting clips takes longer than usual.
- When the SD card contains a large number of clips, some operations may take longer than usual. Save your clips
Cannot copy clips.
- There is not enough available space on the SD card being copied to or the SD card already contains the maximum
Cannot select clips or photos.
- You cannot select more than 100 individual clips or photoshe [Allption instead of [Select].
Indicators and Onscreen Displays
ì lights up in red.
- Battery pack is exhausted. Replace or harge tbattery pack.
í appears on the screen.
- The camcorder cannot communicate with the battery pack attached so the remaining battery time cannot be
displayed.
The tally lamps do not illuminate.
- Set [Other Functions] > [Tally Lamp] > [Front] or [Rear] to [On].
The tally lamps flash quickly.
(4 flashes per second)
- The battery pack is exhausted. Replace or charge the battery pack.
- There is not enough available space on both SD cards. Delete some clips (A 112) to free some space or replace the
SD card.
- A system error has occurred. Turn off the camcorder and back on again. If this does not solve the problem, consult a
Canon Service Center.
The tally lamps flash slowly.
(1 flash per second)
- The combined available space on both SD cards is low. Replace the SD card.
* appears in red on the screen.
- An SD card error occurred. Turn off the camcorder. Remove and reinsert the SD card. Initialize the SD card (A 40) if
the display does not change back to normal.
- The SD card is full. Replace the SD card or delete some clips (A 112) or photos (A 129) to free some space on the
SD card.
Even after stopping recording, the SD card access indicator stays illuminated in red.
- The clip is being recorded. This is not a malfunction.
appears in yellow on the screen.
- The camcorder’s internal temperature has reached a predetermined level. You can continue using the camera.
appears in red on the screen.
- In
mode, when [Other Functions] > [Fan] is set to [Automatic], the cooling fan will start automatically (
appears on the screen).
Troubleshooting
appears on the screen.
- The camcorder and lens cannot communicate normally. Clean the lens’s contacts and reattach the lens.
150
Picture and Sound
Screen displays turn on and off repeatedly.
- The battery pack is exhausted. Replace or charge the battery pack.
- Remove the battery pack and reattach it correctly.
Abnormal characters appear on the screen and the camcorder does not operate properly.
- Disconnect the power source and reconnect it after a short time. If the problem still persists, perform one of the
following actions.
• Disconnect the power source and press the RESET button. This resets all the camcorder’s settings to default values
except for custom picture settings and the hour meter.
• Use the [Other Functions] > [Reset] > [All Settings] function. This resets all the camcorder’s settings to default
values except for the hour meter.
Video noise appears on screen.
- Keep a distance between the camcorder and devices that emit strong electromagnetic fields such as near powerful
magnets and motors, MRI machines or high-voltage power lines.
Horizontal bands appear on the screen.
- This is a phenomenon typical of CMOS image sensors when recording under some types of fluorescent, mercury or
sodium lamps. This is not a malfunction. You may be able to reduce the ymptoms by setting [Camera Setup] >
[Flicker Reduction] to [Automatic] and/or by setting the shutter modto peed] and the shutter speed to a value
matching the frequency of the local electrical system: 1/50* o100 foHz systems, 1/60 or 1/120 for 60 Hz
systems.
* May not be available depending on the frame rate.
No picture appears on the viewfinder.
- No picture will be output to the viewfinder if a caecteto the HDMI OUT or AV OUT terminal in playback
mode. Remove the cable.
No onscreen displays appear on the vieinder.
- In
mode, [Video Setup] > [Charter Disay] is set to [Ext. Out]. Set it to [VF].
Audio cannot be recorded.
- The audio input switch is not set correctly (A 74) or the audio recording level is not set correctly (A 75, 78).
- An external microphone connected to the XLR terminal requires phantom power. Set the XLR terminal switch to
Audio is recorded at an extremely low level.
- The AUDIO LEVEL switch is set to M, and the recording level is set too low. When using the MIC terminal: [Audio
Setup] > [Audio Input] > [MIC Mode] is set to [Manual] and the [MIC Level] setting is too low. Check the audio level
Sound is distorted or is recorded at lower levels.
- When recording near loud sounds (such as fireworks, shows or concerts), sound may become distorted or it may not
be recorded at the actual levels. Activate the microphone attenuator (A 76, 79), or adjust the audio recording level
The picture is displayed correctly but there is no sound from the built-in speaker.
- If headphones are connected to the camcorder, disconnect them.
SD Cards and Accessories
Cannot insert the SD card.
- The SD card you are trying to insert is not facing the correct direction. Turn it over and insert it.
Troubleshooting
Cannot record on the SD card.
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
- The SD card is full or it already contains the maximum number of clips (3,999 clips). Delete some clips (A 112) or
- The folder and file numbers have reached their maximum value. Set [File Numbering] to [Reset] (A 147) and insert a
new SD card.
151
Recording to and playing back from an SD card is slow.
- This may occur as clips and photos are recorded/deleted over time. Save your recordings (A 123) and initialize the
The optional RC-V100 Remote Controller or commercially available remote control does not work.
- Make sure that the [Other Settings] > [REMOTE Term.] setting is set to [RC-V100] when using the optional RC-V100
Remote Controller or [Standard] when using a commercially available remote control.
- When [Camera Setup] > [/CINEMA Locked] is set to [On] or a custom picture file is not selected, custom picture
settings cannot be adjusted using the RC-V100. Set [/CINEMA Locked] to [Off] or select a custom picture file ([C1]
- Turn off the camcorder, reconnect the RC-V100 or other remote control and then turn the camcorder back on again.
Connections with External Devices
Video noise appears on a nearby TV screen.
- When using the camcorder in a room where a TV is located, keep istce between the compact power adapter and
the power or antenna cables of the TV.
Playback looks fine on the camcorder but there is no imagexternmonitor.
- The camcorder is not connected correctly to the external mMake sue you are using the correct connection
- The video input on the external monitor is not seo rminal to which you connected the camcorder. Select
the correct video input.
The camcorder is connected using a comercially ae HDMI cable, but there is no picture or sound from the
external monitor.
- Disconnect the HDMI cable and then reore thconnection or turn the camcorder off and then on again.
The computer does not recognize the camcorder even though the camcorder is connected correctly.
- Disconnect the USB cable and turn off the camcorder. After a short while, turn it on again and restore the connection.
- Connect the camcorder to a different USB port on the computer.
- USB connection is not available while the [Shot List] index screen is displayed. Press the INDEX button to return to the
List of Messages
Refer to this section if a message appears on the screen. The messages in this section appear in alphabetical
order.
Accessing *A/*B Do not remove
- You opened the SD card compartment cover while the camcorder was accessing the SD card. Close the SD card
compartment cover.
CamerabLens communication error. Clean the lens’s contacts and reattach the lens.
- The camcorder cannot correctly communicate with the lens due to dirty lens contacts. After the message disappears,
the
icon appears on the screen. Clean the lens's contacts and reattach the lens.
Cannot acquire battery information
- Battery information can be displayed only for batteries bearing the Intelligent System mark.
Cannot acquire battery information Continue using this battery pack?
- If you are using a battery pack that bears the Intelligent System mark, there may be a problem with the camcorder or
battery pack. Consult a Canon Service Center.
Troubleshooting
Cannot play back
- The file control information is corrupted or there was a decoder error. Turn off the camcorder and back on again. If this
does not solve the problem, consult a Canon Service Center.
• Corrupted file control information cannot be recovered. SD cards or clips with corrupt file control information cannot
be read by the supplied software, Data Import Utility.
152
Cannot record
- The file control information is corrupted or there was an encoder error. Turn off the camcorder and back on again.
Then, remove the SD card being used and reinsert it. Alternatively, replace the SD card. If this does not solve the
problem, consult a Canon Service Center.
• Corrupted file control information cannot be recovered. SD cards or clips with corrupt file control information cannot
be read by the supplied software, Data Import Utility.
Cannot switch SD card slots
- The SLOT SELECT button was pressed while the camcorder is recording. Wait until recording is finished to change the
selected SD card slot.
Change the battery pack
- The battery pack is exhausted. Replace or charge the battery pack.
Check *A/*B
- The SD card cannot be accessed. Check that the SD card is inserted correctly and not malfunctioning.
- Due to an SD card error, recording on/playback from the SD card is not possible. Remove and then reinsert the SD
card or use a different SD card.
- If after the message disappears, the SD card access indicator illuminates in red, perform the following: Turn off the
camcorder and remove and reinsert the SD card. If the SD card access icator illuminates in green, you can resume
recording/playback. If the problem persists, save your recordings (12and initialize the SD card (A 40).
Check the data on *A/*B Initializing the card is also recded
- The SD card cannot be used for any of the following reaso
• A problem has occurred with the SD card.
• The camcorder cannot read the SD card’s dat
• The SD card was initialized using a coter.
• The SD card has been partitioned.
Data on *A/*B needs recovering Attemt to cover?
- If data on the SD card is corrupted, such as when the power suddenly turned off while recording, the data must be
recovered. When this message appears, select [OK] and then press the joystick.
Data on *A/*B needs recovering Change the position of the LOCK switch on the memory card.
- This message will appear the next time you turn on the camcorder if power supply was accidentally interrupted while
the camcorder was writing on the SD card and later the position of the SD card's LOCK switch was changed to
prevent erasure. Change the position of the LOCK switch.
Fan error
- The cooling fan has stopped working or may not be working properly. Consult a Canon Service Center.
File name error
- The folder and file numbers have reached their maximum value. Set [File Numbering] to [Reset] (A 147) and delete all
Invalid operation
- The following operations cannot be performed.
• In
mode, immediately reviewing a recording made using pre-recording or double slot recording.
• Pressing the START/STOP button when there is no SD card in the camcorder.
• During continuous recording mode, pressing the START/STOP button while continuous recording is stopped and
recording is not possible (not enough space on the SD card, or maximum number of shots or continuous recording
clips already recorded).
Lens error Change the frame rate
- The lens attached to the camcorder is not compatible for shooting at the frame rate selected on the camcorder. Select
Lens error Turn the camcorder off, then on again.
- There was a communication error between the camcorder and the lens. Turn the camcorder off and then on again.
Lens firmware update Firmware update failed. Try updating again.
- The lens's firmware could not be correctly updated. Try updating the lens's firmware again.
Troubleshooting
Media full
- SD card A and SD card B are full. Delete some clips (A 112) or photos (A 129) to free some space or replace one or
both SD cards.
Media is almost full
- The amount of available space on SD card A and SD card B combined is low. Replace one or both SD cards.
153
Memory card cover is open
- The SD card compartment cover was open when the camcorder was switched to or turned on in
the compartment cover.
mode. Close
No clips
- There are no clips on the SD card to play back. Clips must be recorded (A 45) in order to play them back.
No photos
- There are no photos on the SD card to play back. Photos must be taken (A 125) in order to view them.
Pre Rec was canceled. Activate Pre Rec again?
- Pre-recording was deactivated automatically after the camcorder was left in record pause mode for about 1 hour with
pre-recording activated. Select [On] and then press the joystick to activate pre-recording again.
Pre Rec will be canceled in a moment.
- The camcorder has been in record pause mode for about 1 hour with pre-recording activated. Pre-recording will be
deactivated automatically in approximately 1 minute.
Recorded at 50.00 Hz/59.94 Hz Check the data on *A/*B Initializing the card is also recommended
- The SD card contains clips that were recorded using a recording type (system frequency) other than the one currently
used by the camcorder. To record on this SD card, save your clips (A 23) and initialize the SD card (A 40). To play
back the recordings on the SD card, set [w Other Functions] > [SysteFrequency] to [59.94 Hz] or [50.00 Hz] as
necessary, so the camcorder matches the SD card.
This photo cannot be displayed
- You may not be able to display photos taken with other deimage s created or edited on a computer.
*A/*B Buffer overflow. Recording was stoppe
- The data transfer rate was too high for the SD cand e recording was stopped. Use a recommended card
*A/*B Cannot record movies on this memory card
*A/*B Cannot restore
*A/*B Cannot start continuous rec
- You have already recorded the maximum number of continuous recording clips (200 clips) in a single SD card. Replace
the SD card(s).
*A/*B May not be possible to record movies on this memory card
- You may not be able to record video on an SD card without a speed class rating or rated SD Speed Class 2. Replace
the SD card with one rated SD speed class 4, 6 or 10.
*A/*B Media full
- SD card A or SD card B is full so recording will not start. Switch to the SD card in the other SD card slot to record.
*A/*B Memory card is write-protected
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
*A/*B Number of clips already at maximum
- The SD card selected for recording already contains the maximum number of clips (3,999 clips). Replace the SD card
or use the SD card in the other SD card slot.
- Because both SD cards reached the maximum number of clips, double slot recording is not available.
• During double slot recording, both “*A” and “*B” will appear in the message.
*A/*B Number of shots already at maximum
- You have already recorded the maximum number of shots (3,999 shots) in a single SD card. When using two SD cards,
you cannot record additional shots on either SD card. To add more shots, replace the SD card(s).
*A/*B Number of shots in this clip already at maximum
- You have already recorded the maximum number of shots (950 shots) in a single continuous recording clip.
Continuous recording can continue but you cannot record additional shots. To add more shots, stop the continuous
Troubleshooting
*A/*B Reached the recording limit for one clip. Recording was stopped.
- When recording a single clip for an extended period of time, the clip will be split into smaller video files every 2 GB.
This message will appear when the number of smaller video files reaches 50.
*A/*B Recording was stopped.
- The file control information is corrupted or there was an encoder error. Turn off the camcorder and back on again.
Then, remove the SD card being used and reinsert it. Alternatively, replace the SD card. If this does not solve the
problem, consult a Canon Service Center.
154
• Corrupted file control information cannot be recovered. SD cards or clips with corrupt file control information cannot
be read by the supplied software, Data Import Utility.
*AJ*B / *BJ*A Switched
- This message appears when you use the SLOT SELECT button to switch the SD card slot in use or recording
continued from one SD card to the other.
*AJ*B / *BJ*A Will switch in a moment
- The SD card is almost full so recording will continue on the other SD card in approximately 1 minute.
Handling Precautions
Handling Precautions
Camcorder
Be sure to observe the following precautions to ensure maximum performance.
155
• Do not carry the camcorder by the LCD panel. Be careful when closing the LCD panel.
• Do not leave the camcorder in places subject to high temperatures (like the inside of a car parked under direct
sunlight), or high humidity.
• Do not use the camcorder near strong electromagnetic fields such as near powerful magnets and motors, MRI
machines or high-voltage power lines. Using the camcorder in such places may cause anomalies in the video or
audio or video noise to appear.
• Do not use or store the camcorder in dusty or sandy places. The camcorder is not waterproof – avoid also
water, mud or salt. If any of the above should get into the camcorder it may damage the camcorder and/or the
lens. Consult a Canon Service Center as soon as possible.
• Be careful to avoid dust and dirt particles accumulating on the lens or entering the camcorder. When you finish using
the camcorder, make sure to attach the body cap to the lens mount and the lens cap and dust cap to the lens.
• Do not point the camcorder or viewfinder toward an intense light source, such as the sun on a sunny day or an
intense artificial light source. Doing so may damage the image sensor or the camcorder's internal
components. Be careful especially when using a tripod or shoulder strap. When you are not using the
camcorder, make sure to attach the body cap to the camcorder.
• Be careful of heat generated by lighting equipment.
• Do not disassemble the camcorder. If the camcorder does not fuon properly, consult qualified service
personnel.
• Do not touch the lens contacts on the lens mou. Dirty acts may cause a poor
contact between the camcorder and the lens in correct operation of the
camcorder. After removing the lens, make suh thbody cap to the lens
mount and the lens cap and dust cp to the le
• Handle the camcorder with care. Do not subject the camcorder to shocks or vibration
as this may cause damage. When usig the houlder strap, do not allow the
camcorder to swing and hit an object.
Long-term storage
If you do not intend to use the camcorder for a long time, store it in a place free of dust, in low humidity, and at
temperatures not higher than 30 °C (86 °F).
Battery Pack
DANGER!
Treat the battery pack with care.
• Keep it away from fire (or it might explode).
• Do not expose the battery pack to temperature higher than 60 °C (140 °F). Do not leave it near a heater or
inside a car in hot weather.
• Do not try to disassemble or modify it.
• Do not drop it or subject it to shocks.
• Do not get it wet.
• Dirty terminals may cause a poor contact between the battery pack and the camcorder. Wipe the terminals
with a soft cloth.
Handling Precautions
Long-term storage
• Store battery packs in a dry place at temperatures no higher than 30 °C (86 °F).
• To extend the battery life of the battery pack, discharge it completely before storing it.
• Charge and discharge all your battery packs fully at least once a year.
156
Always attach the battery terminal cover.
Do not allow any metal objects to touch the terminals (figure 1), as this can
cause a short circuit and damage the battery pack. Attach the terminal cover
whenever the battery pack is not being used (figure 2).
The battery terminal cover has a [ð]-shaped hole. This is useful when you
wish to differentiate between charged and uncharged battery packs. For
example, with charged battery packs, attach the terminal cover so that the
[ð]-shaped hole shows the colored label.
Figure 1
Figure 2
Terminal cover attached
Charged
Back side of the
battery pack
Uncharged
Remaining battery time
If the remaining battery time displayed is not corge e battery pack fully. Still, the correct time may not
be displayed if a fully charged battery pack is usouslin high temperatures or it is left unused for long
periods of time. Also, the correct remaing time me displayed, depending on the battery life. Use the
time shown on the screen as an appromation.
Regarding the use of non-Canon battery packs
• We recommend using genuine Canon battery packs bearing the Intelligent System
mark.
• If you attach to the camcorder battery packs that are not genuine Canon battery packs, the remaining battery
time will not be displayed.
SD Cards
• We recommend backing up the recordings on the SD cards onto your computer. Data may be corrupted or
lost due to defects or exposure to static electricity. Canon shall not be liable for lost or corrupted data.
• Do not touch or expose the terminals to dust or dirt.
• Do not use SD cards in places subject to strong magnetic fields.
• Do not leave SD cards in places subject to high humidity and high temperature.
• Do not disassemble, bend, drop, or subject SD cards to shocks and do not expose them to water.
• Check the direction before inserting the SD cards. Forcing an SD card into the slot if it is not correctly oriented
may damage the SD card or the camcorder.
• Do not attach any labels or stickers on the SD card.
Handling Precautions
• SD cards have a physical switch to prevent writing on the card so as to avoid the
accidental erasure of the card’s content. To write-protect the SD card, set the
switch to the LOCK position.
157
LOCK switch
Built-in Rechargeable Lithium Battery
The camcorder has a built-in rechargeable lithium battery to keep the date/time and other settings. The built-in
lithium battery is recharged while you use the camcorder; however, it will discharge completely if you do not use
the camcorder for about 3 months.
To recharge the built-in lithium battery: Connect the DC cable and compact power adapter to the camcorder
and use a household power outlet to power the camcorder for 24 hours while it is turned off.
Disposal
When you delete data on an SD card, only the file allocation table is altered and stored data is not physically
erased. Take the necessary precautions when you dispose of an SD card, for example by physically damaging it
to prevent the leakage of private data.
If giving an SD card to another person, initialize it using the [Completinitialization option (A 40). Fill it up with
unimportant recordings, and then initialize it again. This makes recvng the original recordings very difficult.
Maintenance/Others
Maintenance/Others
Cleaning
Camcorder Body
158
• Use a soft, dry cloth to clean the camcorder body. Never use chemically treated cloths or volatile solvents
such as paint thinner.
Lens
• Remove any dust or dirt particles using a non-aerosol type blower brush.
• Use a clean, soft lens-cleaning cloth to gently wipe the lens using commercially available cleaning fluid for
eyeglasses. Never use tissue paper.
LCD Screen
• Clean the LCD screen using a clean, soft lens-cleaning cloth.
• Condensation may form on the surface of the screen when the temperature changes suddenly. Wipe it with a
soft dry cloth.
Condensation
Moving the camcorder rapidly between hot and cold temperatures cause condensation (water droplets) to
form on its internal surfaces. Stop using the camcorder if sation detected. Continued use may damage
the camcorder.
Condensation may form in the following cases
• When the camcorder is moved quickfrom com places
• When the camcorder is left in a humroom
• When a cold room is heated rapidly
To avoid condensation
• Do not expose the camcorder to sudden or extreme changes in temperature.
• Remove the SD cards and battery pack. Then, place the camcorder in an airtight plastic bag and let it adjust
gradually to temperature changes before removing it from the bag.
When condensation is detected
The camcorder automatically shuts off.
The precise time required for water droplets to evaporate will vary depending on the location and weather
conditions. As a general rule, wait for 2 hours before resuming use of the camcorder.
Using the Camcorder Abroad
Power Sources
You can use the supplied compact power adapter to operate the camcorder and to charge battery packs in any
country with power supply between 100 and 240 V AC, 50/60 Hz. Consult a Canon Service Center for
information on plug adapters for overseas use.
Optional Accessories
Optional Accessories
The following optional accessories are compatible with this camcorder. The availability differs from area to area.
159
BP-950G, BP-955,
BP-970G, BP-975
Battery Pack
CA-930 Compact
Power Adapter
DC-930 DC Cable
CB-920 Car Battery
Adapter
TA-100 Tripod Adapter
RC-V100 Remote
Controller
STV-250N Stereo Video
Cable
IFC-400PCU
USB Cable
TB-1 Tripod Adapter
Base
For our customers in the USA: Call or visit your local retailer/dealer for genuine Canon video accessories. You
can also obtain genuine accessories for your Canon camcorder by calling: 1-800-828-4040, Canon U.S.A.
Information Center.
Use of genuine Canon accessories is recommended.
This product is designed to achieve excellent performance when used with genuine Canon accessories.
Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the
malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack). Please
note that this warranty does not apply to repairs arising out of the malfunction of non-genuine Canon
accessories, although you may request such repairs on a chargeable basis.
Optional Accessories
Battery Packs
When you need extra battery packs, select from the following: BP-950G,
BP-955, BP-970G, BP-975
When you use battery packs bearing the Intelligent System mark, the
camcorder will communicate with the battery and display the remaining
usage time (accurate to 1 minute). You can only use and charge these battery
packs with camcorders and chargers compatible with Intelligent System.
160
BP-955
BP-975
Charging Times
Use the supplied CA-930 Compact Power Adapter to charge battery packs. The charging times given in the
following table are approximate and vary according to charging conditions and initial charge of the battery pack.
BP-950G
245 min.
BP-955
BP-970G
350 min.
BP-975
200 min.
295 min.
Recording and Playback Times
Recording and playback times given in the following tables are approximate and vary according to recording
mode and charging, recording or playback conditions. The effective usage time of the battery pack may
decrease when recording in cold surroundings, when using the brighter screen settings, etc.
EF lenses with lens contacts draw power from the camcorder to operate some functions. Effective usage times
may decrease depending on the lens used.
Approximate times (LCD screen + viewfinder)
System frequency
59.94 Hz
Bit rate
24 Mbps /
24 Mbps LPCM
Usage time
Recording (maximum
Recording (typical*
Playbac
28.
70 n.
25 min.
280 min.
170 min.
425 min.
280 min.
170 min.
430 min.
295 min.
180 min.
430 min.
295 min.
180 min.
430 min.
300 min.
180 min.
430 min.
P-955
265 min.
160 min.
405 min.
265 min.
160 min.
405 min.
270 min.
165 min.
410 min.
285 min.
170 min.
410 min.
285 min.
170 min.
410 min.
285 min.
175 min.
410 min.
BP-970G
390 min.
235 min.
595 min.
390 min.
235 min.
595 min.
395 min.
240 min.
600 min.
415 min.
250 min.
600 min.
420 min.
250 min.
605 min.
420 min.
255 min.
610 min.
BP-975
405 min.
250 min.
635 min.
410 min.
250 min.
635 min.
415 min.
255 min.
640 min.
430 min.
265 min.
640 min.
430 min.
265 min.
645 min.
450 min.
270 min.
650 min.
17 Mbps
Record(maximum)
Recordinypical*
Playback
7 Mbps
Recording (maximum)
Recording (typical*)
Playback
50.00 Hz
24 Mbps /
24 Mbps LPCM
Recording (maximum)
Recording (typical*)
Playback
17 Mbps
7 Mbps
Recording (maximum)
Recording (typical*)
Playback
Recording (maximum)
Recording (typical*)
Playback
Optional Accessories
Approximate times using the viewfinder
System frequency
59.94 Hz
Bit rate
24 Mbps /
24 Mbps LPCM
Usage time
BP-950G
295 min.
180 min.
295 min.
180 min.
300 min.
180 min.
320 min.
190 min.
320 min.
190 min.
325 min.
190 min.
BP-955
280 min.
170 min.
280 min.
170 min.
285 min.
175 min.
305 min.
180 min.
305 min.
180 min.
310 min.
180 min.
BP-970G
BP-975
430 min.
265 min.
430 min.
265 min.
440 min.
270 min.
470 min.
280 min.
470 min.
280 min.
475 min.
285 min.
Recording (maximum)
Recording (typical*)
Recording (maximum)
Recording (typical*)
Recording (maximum)
Recording (typical*)
Recording (maximum)
Recording (typical*)
Recording (maximum)
Recording (typical*)
Recording (maximum)
Recording (typical*)
405 min.
250 min.
415 min.
250 min.
420 min.
250 min.
435 min.
260 min.
435 min.
260 min.
445 min.
265 min.
161
17 Mbps
7 Mbps
50.00 Hz
24 Mbps /
24 Mbps LPCM
17 Mbps
7 Mbps
* Approximate times for recording with repeated operations such as start/stop, and power on/off.
CB-920 Car Battery Adapter
Use the car battery adapter to arge battery packs on the go. The car
battery adapter plugs into yur r’s cigarette lighter socket and runs off a
12-24V DC negative gund bay.
TA-100 Triter
Te TA-100 ou to quickly mount/unmount the camcorder on/from a
trod.
SBR-1000 Shooting Brace
Using the SBR-1000 for additional support of the camcorder with the neck
strap will significantly lighten the load of the camcoder’s weight while
shooting.
This mark identifies genuine Canon video accessories. When you use Canon video equipment, we
recommend Canon-brand accessories or products bearing the same mark.
Specifications
Specifications
C100
System
162
• Recording System
Movies: AVCHD
Video compression: MPEG-4 AVC/H.264
Audio compression: Linear PCM, 16 bits, 48 kHz, 2ch;
Dolby Digital 2ch
Photos: DCF (Design rule for Camera File system), compatible with Exif Ver. 2.3, JPEG compression
• Video Configuration (recording/playback)
24 Mbps LPCM (VBR), 24 Mbps (VBR), 17 Mbps (VBR):
1920x1080: 60i, 50i, PF30, PF25, PF24, 24P
7 Mbps (VBR):
1440x1080: 60i, 50i, PF30, PF25, PF24, 24P
• Recording Media (not included)
1
SD, SDHC or SDXC memory card (2 slots)
1
Custom picture files, and camera settings files can be saved on and read from the SD card as well.
2
• Maximum Recording Time
16 GB SD Card
24 Mbps LPCM: 85 min., 24 Mbps: 85 min., 17 Mbps 12min., 7 Mbps : 285 min.
32 GB SD Card
24 Mbps LPCM: 175 min., 24 Mbps: 175 minps : 2min., 7 Mbps : 575 min.
Approximate figures based on continuous recording.
2
• Image Sensor: Super-35mm-equivalent CMOapox. 8,290,000 pixels (3840x2160)
• LCD screen: 8.8 cm (3.5 in.), wide, clor, equivpprox. 922,000 dots, 100% coverage
• Viewfinder: 0.61cm (0.24 in.), wide, lor, equivalent to approx. 1,555,000 dots, 100% coverage
• Lens Mount
Canon EF mount compatible with Canon EF lenses (including EF-S lenses)
Lens multiplication factor: approx. 1.53 (for 35mm-equivalent focal length)
• ND Filter: Built-in (Off, 2, 4 or 6 stops), manual
• White Balance
3
Custom white balance (two sets, A and B); two preset settings (daylight, 5,400 K and incandescent lamp,
3
3,200 K ) that can be further fine-tuned; color temperature setting (2,000 K to 15,000 K); automatic white
balance
3
Color temperatures are approximate and given for reference purposes only.
4
• Iris: Manual (1/2-stop increments, 1/3-stop increments, fine-tuning), push auto iris, automatic
4
• Focus: Manual, one-shot AF, continuous AF
4
Only when an EF-S 18-135mm f/3.5-5.6 IS STM or EF-S 18-55mm f/3.5-5.6 IS STM lens is attached to the camcorder.
• ISO Speed
5
5
ISO 320 to ISO 20000, ISO 25600 to ISO 80000 (1-stop or 1/3-stop increments)
• Gain
5
5
-6 dB to 30 dB (3-dB increments), 33 dB to 42 dB (3-dB increments), 0 dB to 24 dB (fine-tuning in 0.5-dB
increments)
5
With extended ISO/Gain range.
• Shutter Speed
Speed (1/3-stop increments, 1/4-stop increments), angle, clear scan, slow, off
6
• Lens Peripheral Illumination Correction: Available for Canon EF lenses
6
Some Canon EF lenses are not compatible with peripheral illumination correction.
Specifications
• Sensor Sensitivity (ISO 640 (0 dB), 2000 lux, 89.9% reflection)
F9 (1920x1080 at 60i) F10 (1920x1080 at 50i)
• S/N Ratio (ISO 850, using Canon Log gamma)
54 dB (typical, 1920x1080, at PF30 /
at PF25)
163
• Subject Illumination (24 dB, with an f/1.2 lens)
0.30 lux (PF30, shutter speed 1/30)
0.25 lux (PF25, shutter speed 1/25)
• Size of Photos: 1920x1080 pixels
Terminals
• HDMI OUT Terminal: HDMI connector, output only, supports time code output
• AV OUT Terminal
∅ 3.5 mm stereo minijack, output only
Video: 1 Vp-p / 75 Ω unbalanced
Audio: -10 dBV (47 kΩ load) / 3 kΩ or less
• USB Terminal: mini-B, Hi-Speed USB, output only
• MIC Terminal
∅ 3.5 mm stereo mini-jack, -72 dBV (manual volume center, full sle -18 dB) / 600 Ω
Microphone attenuator: 20 dB
• × (Headphone) Terminal
∅ 3.5 mm stereo mini-jack, -G to -12 dBV (16 Ω loadme rangMin to Max) / 50 Ω or less
• REMOTE Terminal: ∅ 2.5 mm stereo mini-ja
• Grip Unit Connection Terminal
Proprietary connector for the suppld Grip Unit cection plug
Power/Others
• Power Supply (rated): 7.4 V DC (battery pack), 8.4 V DC (DC IN)
• Power Consumption (recording at 24 Mbps/24 Mbps LPCM, viewfinder/LCD screen normal brightness)
LCD screen and viewfinder:
Viewfinder only:
8.1 W,
7.7 W,
7.6 W
7.3 W
Maximum rated power consumption: 19.6 W
• Operating Temperature: 0 – 40 °C (32 – 104 °F)
• Dimensions (W x H x D)*
Minimal configuration with thumb rest:
135 x 170 x 129 mm (5.3 x 6.7 x 5.1 in.)
Configuration with grip unit:
182 x 170 x 129 mm (7.2 x 6.7 x 5.1 in.)
Configuration with handle unit and grip unit:
182 x 281 x 263 mm (7.2 x 11.1 x 9.3 in.)
* All dimensions are approximate.
• Weight **
Camcorder unit only:
1,020 g (2.2 lb.)
Camcorder with grip unit and grip belt, BP-955 battery pack and two SD cards:
1,475 g (3.3 lb.)
Camcorder with grip unit and grip belt, handle unit, BP-955 battery pack and two SD cards:
1,835 g (4.0 lb.)
** All weights are approximate.
Specifications
Modular Units
Handle Unit
Modular unit includes a cold accessory shoe and socket for 0.64 cm (1/4 in.) screws for other accessories, built-
in microphone, XLR terminals and related audio controls.
164
• CH1, CH2 Terminals
XLR jack (pin1: shield, pin2: hot, pin3: cold), 2 sets
Sensitivity
MIC setting: -60 dBu (manual volume center, full scale -18 dB) / 600 Ω
LINE setting: 4 dBu (manual volume center, full scale -18 dB) / 10 kΩ
Microphone attenuator: 20 dB
• Microphone: Stereo electret condenser microphone
• Weight: Approx. 360 g (12.7 oz.)
Grip Unit
Modular unit can be attached at any of 24 positions (15º intervals); includes limited recording controls.
• Weight: Approx. 230 g (8.1 oz.)
CA-930 Compact Power Adapter
• Rated Input: 100 – 240 V AC, 50/60 Hz
Used as power adapter: 46 VA (100 V AC) – 60 V C)
Used as battery charger: 40 VA (100 V AC) – V A)
• Rated Output
Used as power adapter: 8.4 V DC, 2A
Used as battery charger: 8.4 V DC, 1.5 /2.0 A
• Operating Temperature: 0 – 40 °C (32 – 104 °F)
• Dimensions (W x H x D): Approx. 85 x 51 x 110 mm (3.3 x 2.0 x 4.3 in.)
• Weight: 240 g (8.5 oz.)
BP-955 Battery Pack
• Battery Type: Rechargeable lithium ion battery, compatible with Intelligent System
• Rated Voltage: 7.4 V DC
• Operating Temperature: 0 – 40 °C (32 – 104 °F)
• Battery Capacity
Typical: 5,200 mAh
Minimum: 37 Wh / 4,900 mAh
• Dimensions (W x H x D): 38.2 x 43.5 x 70.5 mm (1.5 x 1.7 x 2.8 in.)
• Weight: 220 g (7.8 oz)
Weight and dimensions are approximate. Errors and omissions excepted.
The information in this manual is verified as of April 2014. Subject to change without notice.
K
R
166
Recording
L
M
S
N
O
T
P
Photos
U
Playback
167
V
W
X
Z
USA
CANON CINEMA EOS LIMITED WARRANTY FOR PRODUCTS PURCHASED IN THE UNITED
STATES
The limited warranty set forth below is given by Canon U.S.A., Inc. ('Canon USA') with respect to (a) the Canon Cinema EOS Product, and (b) the
accessories for the Canon Cinema EOS Product (if any), packaged with this limited warranty (collectively the "Products")* and purchased in the United
States. This limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase. The Products are warranted to the original
end-user purchaser, when delivered in new condition in its original container, under normal use against defective materials or workmanship as follows:
Parts: At Canon USA's option, defective parts will be exchanged for new parts or comparable rebuilt parts for a period of ONE YEAR from the date of
original purchase. Labor: For a period of ONE YEAR from the date of original purchase, labor will be provided free of charge by Canon USA's factory
service centers or designated service facilities located in the United States. When returning Products under this warranty, you must pre-pay the shipping
charges, and you must enclose a copy of the Bill of Sale or other proof of purchase with a complete explanation of the problem. During the ONE-YEAR
warranty period, repairs will be made and the Products will be return-shipped to you free of charge. For repairs after the warranty period is over, you will
be given an estimate of the cost of repair and an opportunity to approve or disapprove of the repair expense before it is incurred. If you approve, repairs
will be made and the Products will be returned to you at your risk and expense. If you disapprove, we will return-ship the Products to you at no charge to
you to an address within the United States.
168
This limited warranty only applies if the Products are used in conjunction with compatible computer equipment and compatible software, as
to which items Canon USA will have no responsibility. Canon USA shall have no responsibility under this limited warranty for use of the
Products in conjunction with incompatible peripheral equipment and/or incompatible software. Non-Canon brand peripheral equipment and
software which may be distributed with, or factory loaded on, the Products, are sold 'AS IS' without warranty of any kind by Canon USA,
including any implied warranty regarding merchantability or fitness for a particular purpose. The sole warranty with respect to such non-
Canon brand items is given by the manufacturer or producer thereof.
*Except for the battery pack packaged with the Products, which carries a separate ninety (90) day limited warranty.
In order to obtain warranty service, please contact the authorized Canon retail dealer from whoyou purchased the Products or contact the CANON
INFORMATION CENTER AT 855-CINE-EOS (855-246-3367) or on the internet at pro.uscanocom/support. You will be directed to the nearest
service facility for your Products.
This Limited Warranty covers all defects encountered in normal use of the Prodoes not aly in the following cases:
A. Loss or damage to the Products due to abuse, mishandlingmpromaintenance, use of non-Canon accessories or failure to follow
operating, maintenance or environmental instructions prescUSAuser's manual;
B. If the Products are defective as a result of leakibatteries, sater damage;
C. If defects or damages are caused by the use oarts or supplies han those sold by Canon USA) that cause damage to the Products or that
cause abnormally frequent service calls or serviproblem
D. If defects or damages are caused by service othean Con USA's factory service centers or authorized service facilities;
E. Any internal modification to product hardware or firmware;
F. Any applicable fee for Maintenance of the Products;
G. If the Product has had its serial number or dating altered or removed.
This Limited Warranty does not apply to Products purchased outside the United States. This Limited Warranty does not apply to accessories or
consumables not originally packaged with the Product. Please retain this warranty card and your Bill of Sale as a permanent record of your purchase. This
card ensures that you are contacted promptly should there be a safety inspection, modification or Product recall under applicable laws or regulations.
NO IMPLIED WARRANTY, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLIES TO THE PRODUCTS AFTER THE
APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTY (EXCEPT AS MENTIONED ABOVE) GIVEN BY ANY PERSON, FIRM OR CORPORATION
WITH RESPECT TO THE PRODUCTS SHALL BIND CANON USA (SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU). CANON USA SHALL NOT BE LIABLE FOR LOSS OF
REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE PRODUCTS OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING
WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE PRODUCTS' HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE PRODUCTS, REGARDLESS OF THE LEGAL THEORY ON
WHICH THE CLAIM IS BASED, AND EVEN IF CANON USA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY
OF ANY KIND AGAINST CANON USA BE GREATER THAN THE PURCHASE PRICE OF THE PRODUCTS SOLD BY CANON USA AND CAUSING THE
ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND
YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE THE PRODUCTS NOT CAUSED
DIRECTLY BY THE NEGLIGENCE OF CANON USA (SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU). THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE
OTHER THAN THE ORIGINAL PURCHASER OF THE PRODUCTS OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
CANON U.S.A., INC.
CANADA
CANON CINEMA EOS LIMITED WARRANTY FOR PRODUCTS PURCHASED IN CANADA
The limited warranty set forth below is given by Canon Canada Inc. ('Canon Canada') with respect to (a) the Canon Cinema EOS product, and (b) the
accessories for the Canon Cinema EOS Product (if any), packaged with this limited warranty (collectively the "Products")* and purchased in Canada. This
limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase. The Products are warranted to the original end-user
purchaser, when delivered in new condition in its original container, under normal use against defective materials or workmanship as follows: Parts: At
Canon Canada's option, defective parts will be exchanged for new parts or comparable rebuilt parts for a period of ONE YEAR from the date of original
purchase. Labor: For a period of ONE YEAR from the date of original purchase, labor will be provided free of charge by Canon Canada's factory service
center or designated service facilities located in Canada. When returning Products under this warranty, you must pre-pay the shipping charges, and you
must enclose a copy of the Bill of Sale or other proof of purchase with a complete explanation of the problem. During the ONE-YEAR warranty period,
repairs will be made and the Products will be return-shipped to you free of charge. For repairs after the warranty period is over, you will be given an
estimate of the cost of repair and an opportunity to approve or disapprove of the repair expense before it is incurred. If you approve, repairs will be made
and the Products will be returned to you at your risk and expense. If you disapprove, we will return-ship the Products to you at no charge to you to an
address within Canada.
169
This limited warranty only applies if the Products are used in conjunction with compatible computer equipment and compatible software, as
to which items Canon Canada will have no responsibility. Canon Canada shall have no responsibility under this limited warranty for use of the
Products in conjunction with incompatible peripheral equipment and/or incompatible software. Non-Canon brand peripheral equipment and
software which may be distributed with, or factory loaded on, the Products, are sold 'AS IS' without warranty of any kind by Canon Canada,
including any implied warranty or condition regarding merchantability or fitness for a particular purpose. The sole warranty with respect to
such non-Canon brand items is given by the manufacturer or producer thereof.
*Except for the battery pack packaged with the Products, which carries a separate ninety (90) day limited warranty.
In order to obtain warranty service, please contact the authorized Canon retail dealer from whom you purchased the Products or contact the CANON
PROFESSIONAL SERVICE CENTRE 1-800-667-2666 or on the internet at www.canon.ca/prYou will be directed to the nearest service facility for your
Products.
This Limited Warranty covers all defects encountered in normal use of the Prod does apply in the following cases:
A. Loss or damage to the Products due to abuse, mishandling, accident, imaintenancuse of non-Canon accessories or failure to follow
operating, maintenance or environmental instructions presanon nada's user's manual;
B. If the Products are defective as a result of leaking batterir wadamage;
C. If defects or damages are caused by the use opartor suhan those sold by Canon Canada) that cause damage to the Products or
that cause abnormally frequent service calls service proble
D. If defects or damages are caused by service er than Cnon Canada's factory service centers or authorized service facilities;
E. Any internal modification to product hardware or mwar
F. Any applicable fee for Maintenance of the Products;
G. If the Product has had its serial number or dating altered or removed.
This Limited Warranty does not apply to Products purchased outside Canada. This Limited Warranty does not apply to accessories or consumables not
originally packaged with the Product. Please retain this warranty card and your Bill of Sale as a permanent record of your purchase. This card ensures
that you are contacted promptly should there be a safety inspection, modification or Product recall under applicable laws or regulations.
NO IMPLIED WARRANTY OR CONDITION, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLIES TO THE
PRODUCTS AFTER THE APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTY (EXCEPT AS MENTIONED ABOVE) GIVEN BY ANY PERSON,
FIRM OR CORPORATION WITH RESPECT TO THE PRODUCTS SHALL BIND CANON CANADA (SOME PROVINCES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY OR CONDITION LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU). CANON
CANADA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE PRODUCTS OR SERVICE, STORAGE
CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE PRODUCTS'
HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE
PRODUCTS, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON CANADA HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST CANON CANADA BE GREATER THAN THE PURCHASE PRICE OF
THE PRODUCTS SOLD BY CANON CANADA AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK
AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE,
MISUSE OR INABILITY TO USE THE PRODUCTS NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CANON CANADA (SOME PROVINCES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU).
THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THE PRODUCTS OR THE PERSON FOR
WHOM IT WAS PURCHASED AS A GIFT.
This warranty gives you specific legal rights, and you may also have other rights which vary from province to province.
CANON CANADA INC.
Canon Inc.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
ASIA and HONG KONG, S.A.R.
NEW ZEALAND www.canon.co.nz
Canon New Zealand Ltd
0800-222-666 (within New Zealand only)
(64) 09-489-0300
Canon Hongkong Company Ltd
19/F, The Metropolis Tower, 10 Metropolis Drive,
Hunghom, Kowloon, Hong Kong
+852 3191 2333,
+852 2428 3963
SINGAPORE
AUSTRALIA www.canon.com.au
Canon Australia Pty Ltd
13-13-83 (within Australia only)
(61) 02-9805-2555
Canon Singapore Pte. Ltd
1 HarbourFront Avenue, #04-01 Keppel Bay Tower,
Singapore 098632
(65) 6799 8888,
(65) 6799 8882
CANADA www.canon.ca/pro
UNITED KINGDOM
CANON CANADA INC.
Canon UK Ltd
❖
Professional Product Support /
Soutien des produits professionnels
(800) 667-2666
CCI Service Centre, Unit 130, Centennial Park,
Borehamood, Hertfordshire, WD6 3SE
04-69-0100
CENTRO Y SURAMÉRICA www.cla.canon.com
CANON LATIN AMERICA, INC.
pro.usacanon.com
ANON U.S.A., INC.
po.usa.canon.com/support
(855) CINE-EOS (855-246-3367)
(USA only)
EUROPE www.canon-europe.com
Canon Europa N.V.
Bovenkerkerweg 59,
1185 XB Amstelveen, The Netherlands
MÉXICO www.canon.com.mx
CANON MEXICANA, S DE RL DE CV
52 (55) 5249-4905
Visit your local Canon Web site to download the latest version of this Instruction Manual.
0166W716
© CANON INC. 2014
PUB. DIE-0429-002
|
Alpine CDE 9874 User Manual
Alpine Electronics Car Stereo System CDE W235BT User Manual
ATN MK 7750 User Manual
Blaupunkt CD 2001 User Manual
Carcomm i Mate Sp5 User Manual
Digital Camera Battery DCB40WB User Manual
Gitzo Classic Studex Mk2 G1326 User Manual
Jensen POWER 880 User Manual
JVC Car Speaker CS FS60 User Manual
JVC GR DVX 2LTD User Manual