/
/
E
INSTRUCTION
MANUAL
Contents
Conventions Used in this Instruction manual .....................2
Handling Cautions..............................................................4
Nomenclature.....................................................................6
Before You Start
11
1
Installing the Batteries ......................................................11
Checking the Battery Level ..............................................12
Mounting and Detaching a Lens.......................................13
How the Shutter Button Works.........................................14
=Loading and Unloading Film ........................................15
¢Midroll Rewind......................................................16
Fully Automatic Shooting
17
2
3
Since everything is automatic, all you do is press the
shutter button.
User-Controlled Shooting
27
You can set the desired shutter speed or aperture value to
obtain the exposure you want. You take control of the
camera.
Reference
49
Symbols
The Caution symbol alerts you to actions to prevent
shooting problems.
The Note symbol gives supplemental information.
3
Handling Cautions
Camera Care and Storage
• The camera is a precision instrument. Do not drop it or subject it to
physical shock.
• The camera is not waterproof and should not be used in wet
conditions or underwater. If the camera gets wet, take it to your
nearest Canon dealer as soon as possible. If small amounts of
water splash onto the camera, wipe it with a clean dry cloth. If the
camera is exposed to salty air, wipe it thoroughly with a slightly
damp cloth.
• Do not leave the camera in places prone to excessive heat such as
in a car on a sunny day. Excessive heat can cause the camera to
malfunction.
• The camera contains precision electronic circuitry. Never attempt to
disassemble the camera.
• Use only a blower brush to blow away any dust on the lens,
eyepiece, mirror, focusing screen, film compartment, etc. Do not
clean the camera body or lens with any cleaner containing an
organic solvent. For stubborn dirt, consult your nearest Canon
Service Center.
• The shutter curtains are extremely thin. Use only a blower to clean
them. Be careful not to blow air too forcefully on the shutter
curtains. The shutter curtains can be easily deformed or damaged.
Also, when loading and unloading film, be careful not to touch the
shutter curtains.
• Do not touch the electrical contacts with your fingers. Otherwise
corrosion may develop on the contacts, resulting in improper
camera operation.
• If the camera is not to be used for an extended period, remove the
battery. Store the camera in a well-ventilated, cool, dry place.
During the storage period, press the shutter button to release the
shutter a few times once in a while.
• Avoid storing the camera in a laboratory, cabinet, etc., where
corrosive chemicals are present.
4
• If the camera has not been used for a prolonged period or if you
will use the camera for an important event, check the operation of
all the camera controls or take the camera to your nearest Canon
Service Center.
LCD Displays
By their nature, LCD displays react more slowly at low
temperatures, and may appear dark at high temperatures. The
display will return to normal at room temperature.
Batteries
• Before installing the batteries, wipe the battery contacts to remove
any fingerprints and smudges. This is to prevent faulty connections
and corrosion.
• Never disassemble or recharge the batteries. Also, never store a
battery in high-temperature places or short circuit the battery
contacts or toss a battery into a fire.
• Although the batteries work well even at low temperatures, battery
performance may decline slightly at freezing temperatures. In such
a case, keep spare batteries warm in a pocket, etc., and use and
warm the batteries alternately.
How Low Battery Levels Affect Camera Operation
On the LCD panel, if the <π> icon blinks or it is not displayed, a
proper exposure can still be obtained as long as the shutter
releases. However, when the battery level is low, film advance and
auto rewind might stop midway or not work at all and <π> icon may
blink on the LCD panel. After the batteries are replaced with new
ones, film advance will be possible and film rewind can resume by
pressing the <¢> button.
Lens Electrical Contacts
After detaching the lens from the camera, put
Contacts
on the lens caps or put down the lens with
the rear end up to avoid scratching the lens
surface and electrical contacts.
5
Nomenclature
• Reference page numbers are indicated by (p.∗∗).
Red-eye reduction lamp
Built-in flash /
AF-assist beam
(p.44/19)
(p.22)
Hot shoe
<^> Film advance mode /
Flash-sync contact
Self-timer/*Remote control button
(p.32/23/24)
<M> Flash button
(p.44)
Mode Dial (p.10)
<l> Main Dial
<£ >
Film plane
mark
Shutter button (p.14)
Strap
mount
(p.7)
*Remote control
sensor / Self-timer/
*Remote control
lamp (p.24/23/24)
Remote
control
terminal**
Grip / Battery
compartment
(p.11)
Lens release
button (p.13)
Depth-of-field
preview button(p.42)
Focus mode switch
(p.13)
Zooming ring
Focusing ring (p.31)
Body cap (p.13)
* DATE Model only
**For Remote Switch RS-60E3 (sold separately).
6
Viewfinder eyepiece
Eyecup (p.26)
<4> AF mode/*SET button (p.28/26)
< > Aperture set/Exposure
compensation button (p.37/39)
Film check
window
<j> AE lock/FE lock
button (p.41/46)
Back
<3> AF point
selection button
(p.29)
cover
release
lever
AF point selection
keys (p.29)
(p.15)
<\>
LCD
panel
(p.8)
Function button
(p.22, 25, 26, 40,
42, 43, 44, 47)
<¢> Midroll
rewind button
(p.16)
Tripod socket
<6> LCD panel illumination
Guide hole
button
Battery compartment
cover release lever
(p.11)
Back cover
Battery compartment
cover (p.11)
Attaching the Strap
Pass the end of the strap through the
camera’s strap mount from the bottom. Then
pass it through the strap’s buckle as shown
in the illustration. Pull the strap to make sure
it does not slip out of the buckle.
1
2
• The eyepiece cover is also attached to the
strap. (p.24)
3
4
Eyepiece cover
7
Nomenclature
LCD Panel
Shutter speed
<?> Manual focus
Aperture value
ISO film speed
Date
Red-eye reduction setting
AEB amount
Date
FE lock
DATE Model
Shooting mode
icon
Date
ISO film speed
Red-eye reduction
Beeper
AF Mode
Safety release lock
Multiple exposures
AEB
One-Shot AF
AI Focus AF
AI Servo AF
Custom Function
Battery level mark
<>> Function pointer
Frame counter
Multiple-exposure setting
Self-timer operation
Remote control operation
<=> Film mark
Film advance mode
<J> Single frame
<H> Continuous
shooting
Custom Function icon
<´> Self-timer/
Exposure level indicator
Exposure compensation amount
AEB level
Red-eye reduction lamp-on indicator
Film transport indicator
Remote control
Non-DATE Model
• Pressing the <6> button
illuminates the LCD panel.
• The actual display will show only the
applicable items.
8
Viewfinder Information
AF points (7)
Focusing screen
Superimposed display
<n> Focus
<j> AE lock / FE lock
confirmation light
AEB in progress
Exposure level indicator
<M> Flash-ready
Improper FE lock
warning
Exposure compensation
amount
AEB level
<|
>
*High-speed sync
(FP flash)
Red-eye reduction
lamp-on indicator
Shutter speed
FE lock
Aperture value
Remove the eyecup, then slide the
dioptric adjustment lever left or right until
the AF points in the viewfinder look
sharp.
* With an EX-series Speedlite.
9
Nomenclature
Mode Dial
The dial is divided into two zones.
OFF
Full Auto
i
1 Basic Zone
2 Creative Zone
Fully automatic mode where
the camera takes care of
everything.
Semi-automatic and manual
modes enable you to take
control of the camera to
obtain the desired result.
Y : Full Auto (p.18)
Basically, all you do is point
and shoot.
T
R
: Program AE (p.33)
: Shutter-priority AE
(p.35)
Image Zone (p.20)
Fully automatic modes for a
particular subject.
E
W
: Aperture-priority AE
(p.36)
: Manual exposure
(p.37)
U
: Portrait
I : Landscape
Q : Automatic Depth-of-
O
P
A
: Close-up
: Sports
field AE (p.38)
3 : : OFF
: Night Portrait
S : Flash off
10
Before You Start
1
Installing the Batteries
∗ Batteries are not included in camera body only (not kit) sold in North
America. Obtain batteries separately.
The camera uses two CR2 lithium batteries.
Open the battery compartment
2
1 cover.
Slide the release lever in the
•
direction shown by the arrow in the
diagram, and open the cover.
1
Install the batteries.
2•
Make sure the battery contacts (+
and –) are properly oriented as
shown.
Do not mix old and new batteries.
•
Close the battery compartment
3cover.
Press the cover until it snaps shut.
The date and time must be set.
See page 26. (DATE Model only)
•
•
For places where CR2 batteries may not be easily available, take
spare batteries with you. Also carry spare batteries for extended
shooting sessions.
11
Checking the Battery Level
Check the battery level after replacing the batteries and before
using the camera.
Turn the Mode Dial to a shooting
mode.
The camera will then turn on and the
LCD panel will display one of the
following battery level mark:
•
: Battery level OK.
: The battery level is low. Keep
spare batteries handy.
: The batteries will soon be
completely exhausted.
: Replace the batteries.
Battery Life
(With 24-ex. rolls)
Temperature 0% Flash Use 50% Flash Use 100% Flash Use
At 20˚C
54 rolls
35 rolls
23 rolls
16 rolls
16 rolls
11 rolls
At –10˚C
• The battery life shown above is based on Canon’s testing
conditions with new batteries.
• If nothing is displayed on the LCD panel, the batteries may have
been installed incorrectly. Take out the batteries and install
correctly.
• If you often press the shutter button halfway for a prolonged
period or just autofocus without taking a picture, the battery life
will be affected.
• When not using the camera, set the Mode Dial to <:>.
12
Mounting and Detaching a Lens
Mounting a Lens
Remove the caps.
1 •
Remove the rear lens cap and the
camera body cap.
Mount the lens.
2•
Align the red dots on the lens and
camera and turn the lens as shown
by the arrow until it snaps in place.
Red dots
On the lens, set the focus mode
3switch to <
>.
AF
If the focus mode switch is set to
•
<
>, autofocus will not operate.
MF
Remove the front lens cap.
1
2
4
1
Detaching the Lens
While pressing the lens release
button, turn the lens as shown
by the arrow.
2
Turn the lens until it stops, then
1
•
detach it.
3
• Keep the removed caps where you will not lose them.
• <AF> stands for “Auto Focus,” and <MF> stands for “Manual
Focus.”
• An EF-S lens cannot be attached to the camera.
13
How the Shutter Button Works
The shutter button has two stages. You can press it down halfway
or fully. The two levels of shutter button operation are as follows:
When it is pressed halfway:
Pressing the shutter button down
•
halfway activates autofocusing
(AF), and also activates the
automatic exposure (AE)
mechanism and sets the shutter
speed and aperture value.
The exposure (the combination of
•
shutter speed and aperture value)
appears on the LCD panel and in
the viewfinder (˜).
When it is pressed fully:
The shutter is released to take the
picture and the film advances by
one frame.
•
If an Extender (optional) is used and the maximum aperture (the
lowest f/number) of the lens becomes smaller than f/5.6, autofocusing
will not operate. For details, refer to the extender's instructions.
Camera movement during the moment of exposure is called
camera shake. Camera shake can cause blurred pictures. To
prevent blurred pictures due to camera shake:
• Hold the camera steady.
· Firmly grasp the camera grip with your right hand, and press
your both elbows lightly against your body.
· Hold the lens at the bottom with your left hand.
·
Press the camera against your face and look through the viewfinder.
· To maintain a stable stance, place one foot in front of the other
instead of lining up both feet.
• Use your finger tip to touch the shutter button, grasp the camera
with your entire right hand, then press the shutter button gently.
14
=Loading and Unloading Film
Loading Film
After you load the film, the camera first winds the entire roll onto the
camera’s take-up spool. With DX-coded film, the camera
automatically sets the film’s ISO speed. Then each time a picture is
taken, one frame of film is rewound back into the film cartridge. The
frame counter shows always number of shots remaining.
Turn the Mode Dial to any
1setting except <:>.
Open the back cover.
2•
Slide down the back cover release
lever and open the back.
Insert the film cartridge at a
3slight angle.
Align the film leader edge with
4the <§> mark.
Hold down the film cartridge while
•
pulling out the film leader. If you
pull out the film leader too much,
rewind it back into the film
cartridge.
Wrong
Close the back cover.
5•
Close the back cover until it snaps
shut.
sFilm prewind will start and there will
be a shutter-release sound about
10 sec. later. The <=> icon and
frame count will also be displayed
on the LCD panel.
sDuring the film prewind, the ISO
speed will be displayed on the LCD
panel.
15
=Loading and Unloading Film
• The shutter curtains have been manufactured with very high
precision. Never touch them with your fingers. When loading film,
do not touch or damage the curtains with your fingers or film.
• In hot and humid environments, do not remove the film packaging
until you are ready to load the film.
• Infrared film cannot be used with this camera.
If the film is not loaded properly, the <=> icon will blink on the LCD
panel and the shutter will not work. Reload the film cartridge
properly.
Unloading Film
After the film’s last frame is exposed, the camera rewinds the film
automatically.
After the film is rewound, there will
be a shutter-release sound. Check
that the <=> icon is blinking on the
LCD panel, then open the back
cover and take out the film cartridge.
¢Midroll Rewind
To rewind the film in midroll, follow the procedure below.
Press the <¢> button.
sFilm rewind will begin.
Make sure the <=> icon is
blinking, then take out film
cartridge.
•
If you take out the film cartridge in midroll without rewinding the film
and then load a new roll of film and press the shutter button
completely, the new film will only rewind into the cartridge. Before
loading a new roll of film in this case, close the camera back and
press the shutter button.
16
Fully Automatic Shooting
YFull Auto Mode ......................................................18
AF-Assist beam with the Built-in Flash .................19
Programmed Image Control Modes ...........................20
UPortrait / ILandscape / OClose-up /
2
PSports / ANight Portrait / SFlash off
FUsing Red-eye Reduction.....................................22
q Self-timer Operation..............................................23
K Wireless Remote Control (DATE Model only)...........24
Using the Eyepiece Cover..........................................24
;Imprinting the Date or Time (DATE Model only).....25
This section explains how to use the camera's Basic Zone modes
<Y> <U> <I> <O> <P> <A> <S> on the Mode Dial for
quick and easy shooting. Each Basic Zone mode suits a particular
subject. The film advance mode, flash, and other functions are set
automatically. You just press the shutter button.
Turn the Mode Dial to <Y>, <U>,
<I>, <O>, <P>, <A> or <S>.
• The picture-taking procedure is the same
as with the “<Y> Full Auto mode” on
page 18.
n
17
YFull Auto Mode
All you do is point the camera and press the shutter button.
Everything is automatic so it is easy to photograph any subject.
With seven AF points to focus the subject, anyone can just point
and shoot.
Turn the Mode Dial to <Y>.
1
Aim any of the AF points on the
2subject.
Out of the seven AF points, the one
•
covering the closest subject is
selected automatically to achieve
focus.
AF point
Focus the subject.
3•
Press the shutter button halfway to
focus.
sWhen focus is achieved, the AF
point mark and focus confirmation
light <n> in the viewfinder will
flash.
Shutter speed
Aperture value
sWhen necessary, the built-in flash
will pop up automatically.
Check the exposure setting.
sThe shutter speed and aperture
value will be set automatically and
displayed in the viewfinder and on
the LCD panel.
4
Focus
confirmation
light
18
Take the picture.
5•
Compose the shot and press the
shutter button fully.
• If you want to zoom, do it before focusing. Turning the zooming
ring after achieving focus may throw off the focus.
• If the built-in flash’s pop-up operation is obstructed, the <π> icon
will blink on the LCD panel. Press the shutter button halfway to
resolve the problem.
• When focus is achieved, the autofocus and auto exposure setting
will also be locked.
• If the focus confirmation light <n> blinks, the picture cannot be
taken. (p.30)
• If multiple AF point marks will light, it means that all of them have
achieved focus at the respective points.
• In the Basic Zone modes (except <I> <P> <S> ), the built-in
flash will pop up and fire automatically in low-light or backlit
conditions. To retract the flash, push it back down.
• If you want to use a certain AF point to focus, set the Mode Dial to
<T> and select the AF point manually. (p.29)
AF-Assist beam with the Built-in Flash
Under low-light conditions, the built-in flash fires a brief burst of
flashes when you press the shutter button halfway. This is to
illuminate the subject to enable easier autofocusing.
• The AF-assist beam does not function in the <I> <P> <S>
modes.
• The AF-assist beam is effective up to about 4 meters/13.1 feet.
• In the Creative Zone modes when the built-in flash is popped up
with the <M> button, the AF-assist beam may be emitted.
19
Programmed Image Control Modes
Select a shooting mode to suit the target subject, and the camera
will be set to obtain the best results.
Portrait
U
This mode blurs the background to make
the human subject stand out.
• Holding down the shutter button executes
continuous shooting.
• To improve the background blur, use a
telephoto lens and fill the frame with the
subject or have the subject stand farther away
from the background.
I Landscape
This is for wide scenic views, night scenes,
etc.
• Using a wide-angle lens will further enhance
the depth and breadth of the picture.
Close-up
O
Use this mode to take close-up shots of
flowers, insects, etc.
• As much as possible, focus the subject at the
lens’ closest focusing distance.
• To obtain a larger magnification, use the
telephoto end of a zoom lens.
A blinking shutter speed indicates that the shutter speed is too slow
to prevent a blurred picture due to camera shake. Be careful to hold
the camera steady and press the shutter button smoothly, or use a
tripod. (The shutter speed indicator still blinks when you use a
tripod, but camera shake will not be a problem.)
20
Sports
P
A
This is for fast-moving subjects when you
want to freeze the action.
• The camera will first track the subject with the
center AF point. Focus tracking will then
continue with any of the seven AF points
covering the subject. When focus is achieved,
the beeper will sound softly.
• While you hold down the shutter button,
focusing will continue for continuous shooting.
• Using a telephoto lens and ISO 400 or higher
speed film is recommended.
Night Portrait
This mode is for taking pictures of people at
twilight or at night. The flash illuminates the
subject while a slow sync speed obtains a
natural-looking exposure of the background.
• If you want to photograph only a night scene
(without people), use the <I> mode
instead.
• Tell the subject to keep still even after the
flash fires.
Use a tripod to prevent camera shake.
Flash off
S
You can disable the flash when you do not
want it to fire.
• The built-in flash or any external Speedlite will
not fire.
21
FUsing Red-eye Reduction (with the built-in flash)
When flash is used in a low-light environment, the subject’s eyes
may come out red in the photograph. To reduce this “Red eye” the
red-eye reduction lamp shines a light into the subject’s eyes before
the flash is fired. Red-eye reduction works in all shooting modes
except <I> <P> <S>.
<
>
Move the
F
•
>
arrow to the
1 <
>
icon on the LCD panel.
Look at the LCD panel and press
the <\> button to move the
arrow. (∫)
Turn the <l> dial to set “
”
2on the LCD panel.
Press the shutter button halfway to
return to normal camera operation.
To cancel red-eye reduction, set
•
•
“
” on the LCD panel.
• When you press the shutter button
halfway, the red-eye reduction lamp-on
indicator will appear in viewfinder and
on the LCD panel.
• Red-eye reduction will not work unless
the subject looks at the red-eye reduction
lamp. Tell the subject to look at the lamp.
Red-eye reduction
lamp-on indicator
• For maximum effectiveness, press the shutter button fully after the
red-eye reduction lamp turns off (after 1.5 sec.).
• You can take a picture even while the red-eye reduction lamp is lit.
• The effectiveness of red-eye reduction varies depending on the
subject.
• To further increase the effectiveness of red-eye reduction, go to a
brighter environment or move closer to the subject.
22
qSelf-timer Operation
You can use self-timer in any Basic mode or Creative mode. We
recommend using a tripod when you use the self-timer.
Press the <^> button.
1 •
While looking at the LCD panel,
press the <^> button to select
<´>.
Take the picture.
2•
The picture-taking procedure is the
same as with the <Y> Full Auto
mode on page 18.
Look through the viewfinder and
press the shutter button fully to
start the self-timer.
•
sThe picture will be taken about 10
sec. later.
First 8 sec.: Self-timer lamp blinks
slowly.
Final 2 sec.: Self-timer lamp blinks
quickly.
sDuring the self-timer operation, the
LCD panel counts down the
seconds until the picture is taken.
Do not stand in front of the camera when you press the shutter
button to start the self-timer. Doing so prevents the camera from
focusing on the subject.
• To cancel the self-timer after it starts, press the <^> button.
• When using the self-timer to take a picture of only yourself, first
lock the focus (p.30) on an object at the same distance where you
will be in the picture.
23
K
Wireless Remote Control (DATE Model only)
With Remote Controller RC-5 (optional), wireless operation is
possible up to 5 m/16.4 ft away from the front of the camera.
Press the <^> button.
1 •
While looking at the LCD panel,
press the <^> button to select
<´>.
Take the picture.
2•
Point the controller toward the
camera’s remote control sensor
and press the transmit button.
sTaken about 2 sec. later.
Remote control sensor
The indicator will be the same as
•
during the last 2 sec. of the self-timer.
Certain types of fluorescent lights might cause the remote control
operation to work improperly. Place the camera away from any
fluorescent lights as far as possible.
If you set <´> and do nothing for four minutes, the remote control
mode will be canceled automatically to save battery power.
Using the Eyepiece Cover
During self-timer or remote control operation when your eye does
not cover the viewfinder eyepiece, stray light may enter the
eyepiece and affect the exposure when the picture is taken. To
prevent this, use the eyepiece cover to cover the eyepiece. (p.7)
Remove the eyecup from the
1 eyepiece.
Attach the eyepiece cover.
2•
Slide the eyepiece cover down into
the eyepiece groove to attach it.
24
;
Imprinting the Date or Time (DATE Model only)
The camera has a date feature with
an automatic calendar to 2099. It
can imprint the date or time on the
photograph as shown in the left
photo.
The date or time can be imprinted in
any shooting mode.
Date position
Move the <>> arrow to <;>.
1 •
Look at the LCD panel and press
<
>
the
\
button. (∫)
If the date and time has not been
•
set, “
will blink on the LCD
”
panel. See page 26 to set the date
and time.
Select the date format.
2•
Turn the <l> dial.
sThe date format will change in the
following loop:
Year, month, day Month, day, year Day, month, year
Blank
Day, hour, minute
25
;Imprinting the Date or Time (DATE Model only)
Setting the Date and Time
Move the < > arrow to <
>.
;
>
1
Select the digit to be set.
2•
<
>
Press the
[
button.
The digit selection will change in
the following sequence: year,
month, day, hour, minute, “ ”.
•
Set the correct number.
3•
Turn the <l> dial.
Repeat steps and
date and time digits are set correctly.
2
3
until all the
•
Finalize the date and time setting.
4•
Keep pressing the <[> button
until no digits are blinking.
If you press the <[> button
while “ ” is blinking, 0 sec. will be
set.
•
If a picture is taken while the date and time are blinking, the date
and time will not be imprinted on that picture.
The date and time setting can be retained for about 10 min. after
the camera’s batteries are removed.
26
User-Controlled Shooting
Selecting the AF mode................................................28
3Selecting the AF point............................................29
Focus Lock ............................................................30
When Autofocus Fails (Manual Focusing) ..................31
3
Selecting the Film Advance Mode .........................32
H
Metering Modes...........................................................32
T Program AE ............................................................33
R Shutter-Priority AE ................................................35
E Aperture-Priority AE .............................................36
W Manual Exposure...................................................37
Q
Depth-of-Field AE..............................38
Automatic
∑Exposure Compensation.....................................39
LAuto Exposure Bracketing (AEB) ..........................40
jAE Lock ..................................................................41
<Multiple Exposures................................................42
Depth-of-Field preview ................................................42
D Setting the ISO Film Speed.................................43
8Beeper Setting........................................................43
7Safety Release Lock..............................................44
Using the Built-in Flash ...............................................44
5Setting Custom Functions ...................................47
With Creative Zone modes, you can set
the desired shutter speed or aperture
value to obtain the exposure you want.
You take control of the camera.
• A ★ next to the page title indicates that
the feature is available only in Creative
Zone modes.
27
★
Selecting the AF mode
The AF mode is the AF operation method. Three AF modes are
provided: ONE SHOT (One-Shot AF), AI FOCUS (AI Focus AF),
and AI SERVO (AI Servo AF).
Select the AF mode.
Press the <4> button (∫) and
turn the <l> dial.
•
ONE SHOT (One-Shot AF)
For still subjects. When you press the shutter button halfway, the AF
focuses once.
sWhen focus is achieved, the AF point achieving focus flashes in red and the
focus confirmation light <n> in the viewfinder lights. The exposure is also set.
AI FOCUS (AI Focus AF)
This mode switches the AF mode automatically to One-Shot AF or AI
Servo AF depending on whether the subject is still or moving.
Ideal for moving subjects whose distance from the camera keeps changing.
The exposure is set at the moment the picture is taken.
•
•
AI SERVO (AI Servo AF)
For moving subjects. While you hold down the shutter button, the
camera continues to focus the subject approaching or moving away
from the camera.
Ideal for moving subjects whose distance from the camera keeps changing.
The exposure is set at the moment the picture is taken.
The beeper will not sound when focus is achieved.
•
•
•
28
★
3Selecting the AF point
The AF point is used for focusing. The AF point can be selected
automatically by the camera or manually by you. In the Basic Zone
modes and <Q> mode, the AF point selection is automatic only.
In the <T> <R> <E> <W> modes, the AF point can be
selected either automatically or manually.
• Automatic AF point Selection
The camera selects the AF point automatically according to
situation.
• Manual AF point Selection
You can select any of the seven AF points manually. This is best
when you want to be sure to focus on a particular subject, or to
compose a particular shot quickly.
Press the <3> button. (∫)
1
sThe currently-selected AF point will
light.
Select the desired AF point.
2•
While looking at the AF point on the
LCD panel or in the viewfinder,
press the cross keys to select the
desired AF point.
To select a horizontal AF point,
press the left or right cross key. To
•
select a vertical AF point, press the
top or bottom cross key.
Select with cross keys
Automatic selection
You can also turn the <l> dial to
select an AF point.
If all the AF points light, automatic
AF point selection will be set.
Press the shutter button halfway to
return to shooting.
•
•
•
Automatic selection
29
★
3Selecting the AF point
Focus Lock
After achieving focus, you can lock the focus on a subject and
recompose the shot. This is called “focus lock.”
Select the desired AF point.
1
Focus the subject.
2•
Aim the AF point on the subject,
then press the shutter button
halfway.
Keep pressing the shutter
3button halfway and recompose
the picture as desired.
Take the picture.
4
• If focus has not been achieved, the focus confirmation light <n>
in the viewfinder will blink. In this case, you cannot take a picture
even when you press the shutter button fully. Recompose the shot
and focus again or see “When Autofocus Fails” (p.31).
• If you use an external, EOS-dedicated Speedlite and focus cannot
be achieved with the AF-assist beam, select the center AF point.
• Focus lock also works in the Basic Zone modes (except <P>).
Just start from step 2 above.
30
When Autofocus Fails (Manual Focusing)
Autofocus can fail to achieve focus (the focus confirmation light
<n> blinks) with certain subjects such as the following:
Difficult Subjects for Autofocusing
• Low-contrast subjects.
Example: Blue sky, flat surface with a solid color.
• Subjects in very low light.
• Extremely backlit or reflective subjects.
Example: Automobile with a strong reflection.
• Overlapping near and far objects.
Example: Animal behind bars in a cage.
• Subjects having a repetitive pattern.
Example: Personal computer keyboard, windows on a building, etc.
In such cases, do one of the following:
(1) Focus lock an object at the same distance as the subject and
recompose.
(2) Set the lens focus mode switch to <MF> and focus manually.
? Manual Focusing
Set the lens focus mode switch
1 to <
>.
MF
Focus the subject.
2•
Focus by turning the lens focusing
ring until the subject is in focus in
the viewfinder.
Focus ring
If you hold down the shutter button halfway while focusing
manually, the active AF point mark and the focus confirmation light
<n> will light when focus is achieved.
31
★
H
Selecting the Film Advance Mode
Two film advance modes are provided: single-frame and continuous
shooting (Max. 3 frames per sec.).
Press the <^> button.
Look at the LCD panel and press
•
<
>
the
^
button.
J : Single frame:
A single picture will be taken when you press the shutter button all
the way.
H : Continuous shooting
Continuous shots will be taken while you hold down the shutter
button all the way.
´ : Self-timer/Remote control
Metering Modes
The camera has three metering modes: Evaluative, partial, and
center-weighted average metering.
Evaluative metering
This is the camera’s standard metering mode suited for
most shooting including backlit conditions. Based on the
subject’s position in the viewfinder, brightness, background,
front or back lighting conditions, etc., the camera always
calculates the proper exposure for the subject.
Partial metering
This mode is set automatically when AE lock is used in
a Creative Zone mode. It is effective for backlit subjects
when there is a strong light behind the subject. The
viewfinder center covering about 9.5% of the viewfinder
area is used for metering. The partial metering area is
shown on the left.
Center-weighted average metering
This is set automatically in the <W> mode. The
metering is weighted at the center and then averaged
for the entire scene.
32
T Program AE
Like the <Y> (Full Auto) mode,
this is a general-purpose mode to
make picture-taking easy. It sets
the shutter speed and aperture
value automatically to suit the
subject’s brightness.
∗ <T> stands for Program.
∗ “AE” stands for auto exposure.
Turn the Mode Dial to <T>.
1
AF point
Focus the subject.
2•
Move the AF point over the subject
and press the shutter button
halfway.
Check the display.
Shutter speed
Aperture value
3
sThe shutter speed and aperture
value are set automatically and
displayed in the viewfinder and on
the LCD panel.
If the shutter speed and aperture
value do not blink, a correct
exposure will be obtained.
•
33
T Program AE
Take the picture.
4•
Compose the shot and press the
shutter button fully.
• If “
” and the maximum aperture value blink, it
indicates underexposure. Use flash.
• If “
” and the minimum aperture value blink, it
indicates overexposure. Use an ND filter to reduce
the light entering the lens.
The Difference Between <T> and <Y>
• The shutter speed and aperture value are set in the same way in
both modes.
• The following features can be used in the <T> mode, but not in
the <Y> mode.
· Manual selection of AF mode · Depth-of-field preview
and AF point
·
AE/FE lock with the <j> button
· Film advance mode selection · Multiple exposures
· Program shift
· Exposure compensation
· AEB
· Built-in flash manual firing and
flash OFF
· High-speed sync
(with EX-series Speedlites)
· Custom Function
About Program Shift
• In the Program AE mode, you can freely change the shutter speed
and aperture value combination (program) set by the camera while
retaining the same exposure. This is called program shift.
• To shift the program, press the shutter button halfway and turn the
<l> dial until the desired shutter speed or aperture value is
displayed.
• Program shift is canceled automatically after the picture is taken.
• Program shift cannot be set when the built-in flash is used.
34
R Shutter-Priority AE
In this mode, you set the shutter speed and the camera sets the
aperture value automatically to suit the subject brightness. A fast
shutter speed can freeze the motion of a fast-moving subject and a
slow shutter speed can blur the subject to give the impression of
motion.
∗ <R> stands for Time value which is the shutter speed.
Turn the Mode Dial to <R>.
1
Select the desired shutter
2speed.
Turn the <l> dial.
The shutter speed can be set in
half-stop increments.
•
•
Focus the subject.
3
sThe aperture value is set
automatically.
Check the viewfinder display
4and take the picture.
If the aperture value display is not
blinking, a correct exposure will be
obtained.
•
• If the maximum aperture value blinks, it indicates
underexposure. Turn the <l> dial to set a
slower shutter speed until the blinking stops.
• If the minimum aperture value blinks, it indicates
overexposure. Turn the <l> dial to set a faster
shutter speed until the blinking stops.
Shutter Speed Display
The shutter speeds from “
the fractional shutter speed. For example, “
sec. Also, “ ” indicates 0.7 sec, and “
” to “ ” indicate the denominator of
” indicates 1/125
” indicates 15 sec.
35
E Aperture-Priority AE
In this mode, you set the desired aperture value and the camera sets
the shutter speed automatically to suit the subject brightness.
The larger the aperture value (smaller aperture), the wider the depth of
field (range of acceptable focus) will be. Vice versa, the smaller the
aperture value (larger aperture), the narrower the depth of field will be.
∗ <E> stands for aperture value.
Turn the Mode Dial to <E>.
1
Select the desired aperture
2value.
Turn the <l> dial.
The aperture value can be set in
half-stop increments.
•
•
Focus the subject.
3
sThe shutter speed is set
automatically.
Check the viewfinder display
4and take the picture.
If the shutter speed display does
not blink, a correct exposure will be
obtained.
•
•
If the slowest shutter speed blinks, it indicates
underexposure. In such a case, turn the <
l> dial
to set a larger aperture value (smaller f/number)
until the shutter speed display stops blinking.
• If the fastest shutter speed blinks, it indicates
overexposure. In such a case, turn the <l> dial
to set a smaller aperture value (larger f/number)
until the shutter speed display stops blinking.
Aperture Value Display
The larger the f/number, the smaller the diaphragm will be. The
aperture value display will differ depending on the lens. When no lens
is attached to the camera, “
” will be display for the aperture value.
36
W Manual Exposure
In this mode, you set both the shutter speed and aperture value as
desired. To determine the exposure, refer to the exposure level
indicator in the viewfinder. This method is called manual exposure.
In the <W> mode, the center-weighted average metering will be set
automatically.
∗ <W> stands for Manual.
Turn the Mode Dial to <W>.
1
Standard exposure index
Exposure level mark
Focus the subject.
sThe exposure setting will be
displayed.
2
The exposure level mark <v>
•
indicates how close the exposure
level is to the correct exposure.
Determine the exposure.
3•
To set the shutter speed, turn the
<l> dial.
To set the aperture value, hold
down the <∑> button and turn
the <l> dial.
•
Take the picture.
4
• If the exposure level mark <v> blinks at the <o> or <t> level,
it indicates that the difference between the standard exposure
exceeds +/–3 stops.
About Bulb Exposures
• If you keep turning the <l> dial counterclockwise,
“
”
will
appear to indicate bulb. The exposure will continue for as long as
you hold down the shutter button completely. With Remote
Controller RC-5, when you press the transmit button, the exposure
will start 2 sec. later. To stop the exposure, press the button again.
• With a new set of batteries, a bulb exposure can last up to 4
hours long at 20˚C.
37
Q Automatic Depth-of-Field AE
This mode is for obtaining a wide depth of field automatically
between a near subject and far subject. It is effective for group
photos and landscapes.
The camera uses the 7 AF points to detect the nearest and farthest
subjects to be in focus.
∗ <Q> stands for Auto-depth of field.
Turn the Mode Dial to <Q>.
1
Focus the subject.
2•
Move the AF point over the subject
and press the shutter button
halfway.
Focus is achieved at all the AF
point marks that light.
•
Take the picture.
3
The <Q> mode cannot be used if the lens’ focus mode switch is
set to <MF>. The result will be the same as using the <T> mode.
• If the aperture value blinks, it indicates that the exposure level is
correct but the desired depth of field cannot be achieved. Either
use a wide-angle lens or move further away from the subjects.
• In this shooting mode, you cannot freely change the shutter speed
and aperture value. If the camera sets a slow shutter speed, hold
the camera steady or use a tripod.
• Regardless of the AF mode setting, ONE-SHOT AF will take effect.
• If flash is used, the result will be the same as using flash in the
<T> mode.
38
★
∑Exposure Compensation
Exposure compensation is used to alter the camera’s standard
exposure setting. You can make the picture look lighter (increased
exposure) or darker (decreased exposure). The exposure
compensation amount can be set up to +/–3 stops in half-stop
increments.
Turn the Mode Dial to a Creative
1 Zone mode except <W>.
Check the exposure setting.
2•
Press the shutter button halfway
and check the display.
Set the exposure compensation
3amount.
Hold down the <∑> button and
turn the <l> dial.
•
To cancel the exposure
compensation, set the exposure
•
compensation amount to <~>.
Standard exposure index
Take the picture.
4
Decreased
exposure
Increased
exposure
Exposure level mark
• The exposure compensation amount set is retained even after the
Mode Dial is set to <:>.
• The exposure compensation amount is canceled automatically
when you turn the Mode Dial to a Basic Zone mode.
• Assuming that a shutter speed of 1/125 sec. and an aperture
value of f/5.6 will give a correct exposure, setting the exposure
compensation amount to plus or minus 1 stop will change the
shutter speed or aperture value as follows:
–1 stop
250
8.0
←
←
←
0
125
5.6
→
→
→
+1 stop
60
4.0
Shutter speed
Aperture value
39
★
LAuto Exposure Bracketing (AEB)
With AEB, the camera automatically changes the exposure within the set
range (up to / 3 stops in 1/2-stop increments) for three successive frames.
+
–
Move the <>> arrow to the
AEB amount
1 <L> icon.
Look at the LCD panel and press
•
the <\> button. (∫)
Set the desired AEB amount.
2•
Turn the <l> dial.
Press the shutter button halfway to
return to normal camera operation.
•
AEB range
Take the picture.
standard exposure
3
sThe three bracketed shots will be
exposed in the following sequence:
standard exposure, decreased
exposure, and increased exposure.
decreased exposure
sAs shown on the left, the respective
bracketing amount will be displayed
as each bracketed shot is taken.
increased exposure
The picture will be taken in the
current film advance mode.
•
After the three AEB shots are
taken, the AEB will not be canceled
automatically. To cancel AEB, set
•
the AEB amount back to “
.”
• During AEB shooting, the <>> arrow will appear next to the
<L> icon and the AEB level <•> will be displayed. In the
viewfinder, the <j> icon will blink.
• In the <H> film advance mode, the camera stops shooting
automatically after taking the three AEB shots. In the <J> (single
frame) mode, press the shutter button completely three times to
take the three AEB shots.
• If you use the self-timer or remote control, the three AEB shots
will be taken continuously automatically.
• AEB can be combined with exposure compensation.
• AEB cannot be used with flash or bulb exposures.
40
★
jAE Lock
AE lock enables you to lock the exposure at a different place from
the point of focus. After locking the exposure, you can recompose
the shot while maintaining the desired exposure level. This feature
is useful for backlit and spotlighted subjects. For AE lock, partial
metering is used automatically.
Focus the subject.
1
sThe exposure setting will be
displayed.
Press the <j> button. (˜)
2•
Aim the center of the viewfinder
over the subject where the
exposure is to be locked, then
press the <j> button.
sThe <j> icon will light in the
viewfinder to indicate that the
exposure setting has been locked
(AE lock).
Each time you press the <j>
button, it locks the current
exposure setting.
•
AE lock indicator
Compose the shot and take the
3picture.
If you want to maintain the AE lock
•
while taking more pictures, hold
down the <j> button and press
the shutter button to take another
picture.
41
★
<Multiple Exposures
Since the film is not advanced after each shot, you can expose
multiple shots on the same frame. You can expose up to nine shots
on a single frame.
Move the <>> arrow to the <<> icon.
1 •
<
>
\
(
)
Look at the LCD panel and press the
button. ∫
s“ ” will be displayed.
Set the desired number of multiple exposures.
2•
Turn the <l> dial.
Press the shutter button halfway to return to normal camera
operation.
•
Take the picture.
sAfter you take all the multiple exposures, the film advances to the next
frame automatically and the multiple-exposure setting is canceled.
3
If you shoot multiple exposures on the first few or last few frames of a roll,
the multiple exposures might not be precisely aligned due to the film curling.
• During multiple-exposure shooting, the <>> arrow next to the <<>
icon on the LCD panel will blink.
• To cancel multiple exposures before shooting, set the number of multiple
exposures to
“
.”
• To cancel multiple exposures after shooting, follow steps
set the number of multiple exposures to blank.
1
and
2
to
★
Depth-of-Field preview
When you press the depth-of-field
preview button, the camera will stop
down the diaphragm to the current
aperture. You can then see the
range of acceptable focus in the
viewfinder.
When you press the depth-of-field preview button, the exposure
setting will be locked (AE lock).
42
★
D Setting the ISO Film Speed
If the film is not DX-coded or if you want to set a different film
speed, load the film in the camera and set the film speed manually
as follows. The settable film speed range is ISO 6 to 6400.
Move the <>> arrow to the
1 <D> icon.
Look at the LCD panel and press
the <\> button to move the
arrow. (∫)
•
sThe current film speed is displayed.
Set the desired film speed.
2•
Turn the <l> dial to set the film
speed.
The manually-set film speed will be canceled if the film is taken out
and DX-coded film is loaded.
8Beeper Setting
Move the <>> arrow to the
1 <8> icon.
Look at the LCD panel and press
•
the <\> button. (∫)
Select the setting
Turn the <l> dial to select the
setting.
“
/
/
”
.
2•
0 : Beeper silent.
1 : Beeper sounds when focus is achieved and during self-timer
operation.
2 : Beeper sounds when focus is achieved, during self-timer
operation, and during slow shutter speeds when camera shake
can blur the shot. In this case, use a tripod.
43
7Safety Release Lock
This prevents shutter release if there is no film loaded or if there is
no lens attached. It is particularly effective against missed shots
due to no film.
If you press the shutter button while there is no film in the camera
or no lens attached, “
” (F: film) or “
” (L: lens) will blink
in the viewfinder and on the LCD panel.
Move the <>> arrow to the
1 <7> icon.
While looking at the LCD panel,
press the <\> button. (∫)
•
Set it to
“
.”
2•
Turn the <l> dial.
To cancel the setting, set it to “ .”
•
Using the Built-in Flash
With E-TTL II autoflash, high-precision and consistent flash exposures
can be obtained.
In a Basic Zone Mode
In low-light or backlit conditions, the built-in flash will pop up and fire
automatically (except in <I> <P> <S> modes).
In a Creative Zone Mode
Press the <M> button to pop up the built-in flash.
T
: Use this mode for automatic flash photography. The flash
sync speed (1/60-1/125 sec.) and aperture value will be set
automatically as with the <Y> (Full Auto) mode.
R
: Use this mode if you want to set the flash sync speed
manually (within 30 sec. - 1/125 sec.). The camera will set
the flash aperture value automatically to obtain a correct
flash exposure.
44
Using the Built-in Flash
E
: Use this mode if you want to set the flash aperture value.
The camera will set the flash sync speed (within 30 sec. -
1/125 sec.) automatically to obtain the best exposure for
the aperture you set. For portraits with a night scene or
dark background, a slow sync speed will be set to obtain a
proper exposure for both the subject and background. The
flash illuminates the subject, while the background is
properly exposed with a slow shutter speed.
• Because automatic slow-sync shooting uses a slow
shutter speed, always use a tripod.
• If you do not want long exposures, set C.Fn-06. (p.48)
W
: You can manually set both the flash sync speed (within Bulb
- 1/125 sec.) and aperture value. The subject is properly
exposed with the flash and the background is exposed with
the flash sync speed and aperture value you have set.
Q : The result will be the same as using the <T> mode.
Flash Distance Range (With EF28-90mm f/4-5.6)
[m/ft]
28mm
90mm
ISO
Negative Film Slide Film Negative Film Slide Film
1 - 4.6 / 3.3 - 15.2 1 - 3.3 / 3.3 - 10.9 1 - 3.3 / 3.3 - 10.9 1 - 2.3 / 3.3 - 7.6
1 - 9.2 / 3.3 - 30.4 1.2 - 6.6 / 3.9 - 21.5 1 - 6.6 / 3.3 - 21.8 1- 4.6 / 3.3 - 15.2
100
400
• When using the built-in flash, stay at least 1 meter/3.3 feet away
from the subject. Otherwise, part of the photo will look dark.
• When using the built-in flash, detach any hood attached to the
lens. A lens hood will partially obstruct the flash coverage.
• When a super telephoto lens or a fast, large-aperture lens is
attached, the built-in flash coverage might be obstructed.
• The built-in flash’s flash coverage is 28mm lens angle.
• To retract the built-in flash, push it down.
• This is a Type-A camera (compatible with E-TTL II autoflash)
which can use all the features of EX-series Speedlites.
45
Using the Built-in Flash
jFE Lock★
FE (Flash Exposure) lock is for setting the correct flash exposure
for any part of the subject. First pop-up the built-in flash.
Focus the subject.
1 •
Keep pressing the shutter button
until step 3.
Aim the viewfinder center over
2the target subject, then press
the <j> button.
sA preflash is fired and the <j>
icon will be displayed in the
viewfinder.
Compose the shot and take the
3picture.
• If the subject is beyond the effective flash range resulting in
underexposure, the <M> icon will blink. Get closer to the subject
and repeat steps 1 and 2.
• For the external Speedlite, use an EX-series Speedlite. If the
camera is used with an EZ-, E-, EG-, ML-, or TL-series Speedlite,
the flash will not fire in the TTL and A-TTL autoflash modes. Use
the manual flash mode if the Speedlite has one.
About E-TTL II Autoflash
E-TTL II is a new autoflash exposure system incorporating
improved flash exposure control and lens focusing distance
information, making it more precise than the previous E-TTL
(evaluative flash metering with preflash) system.
The camera can execute E-TTL II autoflash with any EX-series
Speedlite.
46
★
5Setting Custom Functions
You can customize camera functions to suit your preferences. They
are called Custom Functions.
Display <5> on the LCD
1 panel.
Press the <\> button to display
the icon.
•
Function
Setting No.
Select the Custom Function No.
2•
Turn the <l> dial.
Change the setting.
3•
Press the <[> button. The
button toggles the setting between
“
” and “ .” “ ” is the default
setting.
The <5> icon remains displayed
on the LCD panel and the Custom
Function setting is set.
•
Custom Function
Setting No.
Custom Function Settings
C.Fn-01 Self-timer delay time
The 2-sec. delay is effective for preventing camera shake (when
you press the shutter button) during close-ups and other critical
work.
0 : 10-sec. delay
1 : 2-sec. delay
47
★
5Setting Custom Functions
C.Fn-02 AF point selection method
0 : Press AF point selection button, then press the cross keys.
1 : Press the shutter button halfway, then press cross keys.
Effective during the <˜> and <∫> active times.
Pressing the <3> button switches to automatic AF point
selection.
C.Fn-03 Switch to center AF point with AF point selection button
0 : Disabled
1 : Enabled
C.Fn-04 Emission of built-in AF-assist beam
0 : Enabled
1 : Disabled
C.Fn-05 Shutter curtain sync with built-in flash and EX-series Speedlite
0 : 1st-curtain sync
1 : 2nd-curtain sync
With second-curtain sync and a slow shutter speed, you can
create a light trail following a moving subject. The flash fires
right before the shutter closes. Second-curtain sync can be set
even with EOS-dedicated Speedlites which cannot switch the
shutter curtain synchronization. The Speedlite with a shutter
curtain synchronization setting will override the camera’s
setting.
∗ When you press the shutter button completely, a preflash will be
fired for flash exposure control.
C.Fn-06 Flash sync speed in Av mode
0 : Auto
1 : 1/125 sec. (fixed)
When you use flash in the aperture-priority mode (Av), the flash
sync speed will be fixed at 1/125 sec. This prevents the camera
from setting a slow sync speed in low-light conditions.
48
Reference
Feature Availability Table
: Set automatically.
: User-selectable/settable.
R E W
Mode Dial Mode
One Shot
Y
U
I
O
P
A
S
T
Q
AI Servo
AI Focus
Auto
AF Point
Selection
Manual
Single frame
Continuous
Self-timer/
Remote control
Troubleshooting Guide
If there is a problem, first refer to this Troubleshooting Guide.
Nothing is displayed on the LCD panel.
The batteries are exhausted. / The batteries have been installed incorrectly.
•
Replace the batteries with new ones. / Install the batteries correctly. (p.11)
s
The picture looks blurred.
The lens focus mode switch is set to <MF>.
•
Set the lens focus mode switch to <AF>. (p.13)
s
There was camera shake when the picture was taken.
Hold the camera steady or use a faster shutter speed. (p.14)
s
The shutter does not work.
On the LCD panel, the frame count is not displayed and the <
•
=> icon blinks.
Take out the film and load it correctly. (p.15)
s
The focus confirmation light <n> in the viewfinder blinks and focus
cannot be achieved.
Select another AF point. (p.29) If focus still cannot be achieved, focus manually. (p.31)
s
The <π> icon blinks on the LCD panel.
The battery level is very low.
•
Replace the batteries with new ones. (p.11)
s
A misoperation has occurred.
Press the shutter button halfway. (p.14) / Remove the batteries and reload it. (p.11)
s
If the <π> icon does not stop blinking, consult your nearest service center.
49
Major Specifications
• Type
Type......................................35 mm AF/AE SLR camera with built-in flash
Recording media...................35 mm film
Image size ............................24 x 36 mm
Compatible lenses ................Canon EF lenses (except EF-S lenses)
Lens mount...........................Canon EF mount
• Viewfinder
Type......................................Eye-level pentamirror
Coverage ..............................Approx. 90% vertically and horizontally
Magnification.........................0.7x (–1 diopter with 50mm lens at infinity)
Eyepoint................................18.5 mm
Dioptric adjustment range.....–2.5 - +0.5 dpt
Focusing screen ...................Fixed, all-matte screen
Mirror ....................................Quick-return half mirror
Viewfinder information ..........AF (Superimposed display, focus confirmation light);
Exposure (shutter speed, aperture value, exposure level, AE
lock); Flash (flash ready, hi-speed sync, FE lock, red-eye
reduction, underexposure warning
)
Depth-of-field preview...........Depth-of-field preview button
• Autofocus
Type......................................TTL-CT-SIR with a CMOS (Complementary Metal Oxide
Semiconductor) sensor
AF points...............................7 AF points
AF working range .................EV 1 - 18 (ISO 100)
Focusing modes ...................One Shot AF, AI Servo AF, AI Focus AF, manual focusing (MF)
AF point selection.................Automatic/manual
AF-assist beam.....................Intermittent firing of the built-in flash
Working distance: Approx. 4 m/13.1 ft at center,
Approx. 3.5 m/11.5 ft at outer edge
• Exposure control
Exposure metering modes....TTL full aperture metering with 35-zone SPC
• Evaluative metering (linkable to any AF point)
• Partial metering (approx. 9.5% of viewfinder at center)
• Center-weighted average metering (automatically set in
manual exposure mode)
Metering range......................EV 1 - 20 (normal temperature, 50mm f/1.4, ISO 100)
Exposure control...................Program AE (Full Auto, Portrait, Landscape, Close-up,
Sports, Night Portrait, Flash off), Program AE, shutter-
priority AE, aperture-priority AE, depth-of-field AE, manual
exposure, E-TTL II autoflash
Film speeds ..........................ISO 6 - 6400 (Set automatically for DX-coded film within
ISO 25 - 5000)
Exposure compensation .......Manual exposure compensation: +/– 3 stops in 1/2-stop
increments (can be used with AEB)
Auto Exposure Bracketing (AEB): +/– 3 stops in 1/2-stop increments
AE lock..................................Auto AE lock: Operates in One Shot AF mode with
evaluative metering when focus is achieved
Manual AE lock: By AE lock button in partial metering mode
Multiple exposures................Max. 9 exposures
50
• Shutter
Type......................................Electronically controlled focal-plane shutter
Shutter speeds......................1/4000 - 30 sec. in 1/2-stop increments, bulb, X sync at 1/125 sec.
Shutter release .....................Soft touch electromagnetic release (safety release lock possible)
Self-timer ..............................Shoot after 10 sec. delay
Remote control .....................Remote Controller RC-1/RC-5 (DATE Model only)
• Flash
Built-in flash ..........................E-TTL II autoflash, FE lock possible
Guide No. 13 (ISO 100, in meters), 39 (ISO 100, in feet)
Recycling time: Approx. 2 sec.
Flash coverage: 28 mm lens angle covered
Red-eye reduction: Lamp
External EOS-dedicated flash ...E-TTL II autoflash
• Film transport
Film loading ..........................Automatic prewind
Film advance modes ............Single-frame/continuous shooting
Continuous shooting speeds (approx.) ...One Shot AF: 3 fps, AI Servo AF: 2.5 fps
Film rewind ...........................Automatic. Mid-roll rewind
• Custom Functions.........6
•
Date imprinting (DATE Model only)...Automatic calendar to 2099
• Power source .................Two CR2 lithium batteries
• Dimensions (W x H x D)..130 x 90 x 64 mm/5.1 x 3.5 x 2.5 in
• Weight ..............................365 g/12.7 oz (body only)
• All the specifications above are based on Canon’s testing and measuring standards.
• Specifications and physical appearance are subject to change without notice.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Do not make any changes or modifications to the equipment unless otherwise specified in the
instruction manual. If such changes or modifications should be made, you could be required
to stop operation of the equipment.
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Complies with the Canadian ICES-003 class B specifications.
Respecte les exigences de la class B de la NMB-003 du Canada.
The CE Mark is a Directive conformity mark of the European Community (EC)
51
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
U.S.A.
CANON U.S.A. INC.
For all inquiries concerning this camera, call toll free in the U.S.
1-800-OK-CANON or write to: Customer Relations, Canon U.S.A., Inc.
One Canon Plaza, Lake Success, N.Y. 11042-1198
CANADA
CANON CANADA INC. HEADQUARTERS
6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada
CANON CANADA INC. MONTREAL BRANCH
5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada
CANON CANADA INC. CALGARY OFFICE
2828, 16th Street, N.E. Calgary, Alberta T2E 7K7, Canada
For all inquiries concerning this camera, call toll free in Canada
1-800-OK-CANON
EUROPE,
AFRICA &
MIDDLE EAST
CANON EUROPA N.V.
Bovenkerkerweg 59-61, P.O. Box 2262, 1180 EG Amstelveen,
The Netherlands
CANON COMMUNICATION & IMAGE FRANCE S.A.
102, Avenue du Général de Gaulle 92257 La Garenne-Colombes Cedex, France
CANON UK LTD.
Woodhatch Reigate Surrey RH2 8BF, United Kingdom
CANON DEUTSCHLAND GmbH
Europark Fichtenhain A10, 47807 Krefeld, Germany
CANON ITALIA S.p.A.
Via Milano 8, San Donato M.SE, Milano, Italy
CANON Schweiz AG
Geschäftsbereich Wiederverkauf, Industriestrasse 12, CH-8305 Dietlikon,
Switzerland
CANON G. m. b. H.
Oberlaaerstrasse 233, 4th floor, 1100 Wien, Austria
CANON España, S. A.
C/Joaquín Costa, 41, 28002 Madrid, Spain
SEQUE Soc. Nac. de Equip., Lda.,
Praça da Alegria, 58, 2°, 1269-149 Lisboa, Portugal
CENTRAL &
SOUTH AMERICA
CANON LATIN AMERICA, INC. DEPTO DE VENTAS
703 Waterford Way Suite 400 Miami, FL 33126 U.S.A.
CANON LATIN AMERICA, INC. CENTRO DE SERVICIO Y REPARACION
Apartado 2019, Zona Libre de Colón, República de Panamá
ASIA
CANON HONGKONG CO., LTD.
9/F, The Hong Kong Club Building, 3A Chater Road, Central, Hong Kong
CANON SINGAPORE PTE. LTD.
79 Anson Road #09-01/06 Singapore 079906
OCEANIA
JAPAN
CANON AUSTRALIA PTY. LTD.
1 Thomas Holt Drive, North Ryde, N.S.W. 2113, Australia
CANON NEW ZEALAND LTD.
Akoranga Business Park, Akoranga Drive, Northcote, Auckland, New Zealand
CANON SALES CO., INC.
16-6, Kohnan 2-chome, Minato-ku, Tokyo 108-8011, Japan
This Instruction booklet is current as of August 2004. For information on
using the camera with system accessories introduced after this date, contact
your nearest Canon Service Center.
CANON INC. 2004
PRINTED IN TAIWAN
©
|