Arcam FMJ Blue Ray Disc Player BDP100 User Manual

BDP100  
Handbook Blu-ray Disc player  
ULTRAHIGHPERFORMANCE24-BITDAC  
ank you and congratulations for purchasing your Arcam FMJ Blu-ray Disc player.  
contents  
safety...........................................................E-2  
welcome......................................................E-3  
installation .................................................E-4  
Arcam has been producing specialist hi-fi and home cinema products of remarkable quality  
for over three decades and the BDP100 – which plays Blu-ray Discs, DVD-Video discs and  
Audio CDs – is the latest in a long line of award winning home cinema equipment. e design  
of the FMJ range draws upon all of Arcam’s experience as one of the UK’s most respected audio  
companies and is built to give you years of trouble-free listening enjoyment.  
welcome  
Placing the unit ..................................................... E-4  
Power......................................................................... E-4  
The remote control and trigger inputs......... E-4  
Interconnect cables.............................................. E-4  
Making video connections................................ E-6  
Making audio connections ............................... E-6  
The HDMI interface .............................................. E-7  
About HDMI ........................................................... E-7  
Connecting using HDMI..................................... E-7  
Troubleshooting HDMI....................................... E-7  
is handbook has been designed to give you all the information you need to install, connect  
and use the Arcam BDP100 Blu-ray Disc player. e CR104 remote control handset supplied  
with this equipment is also described. Use the contents list shown on this page to guide you to  
the section of interest.  
We hope that your FMJ Blu-ray Disc player will give you years of trouble-free operation. In the  
unlikely event of any fault, or if you simply require further information about Arcam products,  
our network of dealers will be happy to help you. Further information can also be found on the  
Arcam website at www.arcam.co.uk.  
disc & file formats .....................................E-8  
Playable discs ......................................................... E-8  
Playable files ........................................................... E-8  
Region coding........................................................ E-8  
Network connection............................................ E-9  
USB connection..................................................... E-9  
e FMJ development team  
basic operation....................................... E-10  
remote control........................................ E-11  
Controlling the BDP100....................................E-12  
Advanced controls..............................................E-13  
Useful information..............................................E-14  
Device Mode / Source keys.............................E-14  
Controlling other devices ...............................E-15  
Code blink-back...................................................E-15  
customising the CR104......................... E-26  
Code Learning......................................................E-26  
Creating Macros ..................................................E-27  
Volume punch-through ...................................E-27  
Key Mover..............................................................E-27  
Mode Mover..........................................................E-28  
Locking/Unlocking.............................................E-28  
Mode key IR punch-through ..........................E-29  
Resetting the CR104 ..........................................E-29  
Command summary..........................................E-29  
Device codes.........................................................E-29  
IR commands .......................................... E-30  
specifications.......................................... E-31  
Radio interference..............................................E-31  
Laser radiation......................................................E-31  
advanced operation.............................. E-16  
Disc Information..................................................E-16  
Menus......................................................................E-16  
Soundtrack Selection ........................................E-16  
Subtitles..................................................................E-16  
Bonusview & BD-Live.........................................E-17  
Playing files ...........................................................E-18  
Advanced playback controls ..........................E-19  
settings menus....................................... E-20  
troubleshooting..................................... E-23  
audio & video output formats............. E-24  
software licencing ................................. E-32  
product guarantee ................................ E-33  
device code tables.....................................34  
Audio output format .........................................E-24  
Video Output Resolution.................................E-25  
e-3  
Arcam’s BDP100 provides class-leading sound quality from  
Blu-ray Discs, DVD-Video discs and compact discs.  
e BDP100 has a state-of-the-art Delta-Sigma DAC  
(Digital-to-Analogue Converter) which provides audiophile  
sound quality for video and audio discs.  
installation  
e BDP100 is supplied with the CR104 ‘universal’ remote  
control, which is simple to use and can control up to eight  
audio devices – such as an amplifer, television or Personal  
Video Recorder.  
e high performance BDP100 Blu-ray Disc player is  
designed to truly bring your movies and music to life.  
Placing the unit  
Power  
e remote control input requires a mono 3.5mm  
jack, with the tip active and the sleeve grounded.  
<
Place the BD player on a level, firm surface,  
avoiding direct sunlight and sources of heat or  
damp.  
e BD player is supplied with a moulded mains plug  
already fitted to the lead. Check that the plug supplied  
fits your supply – should you require a new mains lead,  
please contact your Arcam dealer.  
e remote control signals must be in modulated  
rC5 format (at 36kHz), with a voltage level of  
between 5V and 12V.  
<
<
Do not place the BD player on top of an amplifier  
or other source of heat.  
Do not place the BD player in an enclosed space  
such as a bookcase or closed cabinet unless there  
is good provision for ventilation. e BD player is  
designed to run warm during normal operation.  
If your mains supply voltage or mains plug is different,  
please contact your Arcam dealer immediately  
e RS232 input is for optional connection to a home  
automation system or a computer. Various third-party  
sytems are available providing sophisticated control  
over all your entertainment devices using touch screens  
etc. Contact your dealer or installer for further details.  
e technical details of the remote control protocol  
are available from Arcam on request (email support@  
arcam.co.uk).  
Push the IEC plug end of the power cable into the  
socket on the back of the BD player, making sure that it  
is pushed in firmly. Plug the other end of the cable into  
your mains socket and, if necessary, switch the socket  
on.  
<
<
<
Do not place any other component or item on  
top of the BD player as this may obstruct airflow  
around the unit, causing the BD player to run hot.  
Make sure the remote-control receiver (next to  
the display on the front panel) is unobstructed, or  
remote control will be impaired.  
Do not place your record deck on top of this  
unit. record decks are very sensitive to the noise  
generated by mains power supplies which will be  
heard as a background ‘hum’ if the record deck is  
too close.  
The remote control and trigger  
inputs  
e REMOTE IN input can be used to pass rC5 codes  
(listed on page E-30) to the BDP100 if it is installed in a  
position, or a system, where infrared cannot be used. If  
this is required, please contact your dealer for further  
information.  
e TRIggER IN input can be used to switch the BDP100  
in and out of stand-by. Connecting the trigger output of  
your Arcam amplifier (or other compatible device), will  
cause the BDP100 to come out of stand-by automatically  
when the amplifier is switched on, returning to stand-by  
when the amplifier is switched off. Please see your  
amplifier handbook for further information.  
interconnect cables  
We recommend the use of high-quality screened cables  
that are designed for the particular application. Other  
cables will have different impedance characteristics  
that will degrade the performance of your system (for  
example, do not use cabling intended for video use to  
carry audio signals). All cables should be kept as short as  
is practically possible.  
It is good practice when connecting your equipment to  
make sure that the mains power-supply cabling is kept  
as far away as possible from your audio cables. Failure to  
do so may result in unwanted noise in the audio signals.  
In normal use there is no need to make any connections  
to these inputs.  
e-4  
analogue audio output  
coaxial digital output  
Connect these to your amplifiers CD (or other  
line-level) input using suitable high quality  
interconnect cables. Ensure that the leſt and  
right audio outputs from the BD player are  
connected to the same leſt and right inputs on  
your amplifier.  
Use this socket if you are using an  
AV receiver with a coaxial digital  
input. Connect to the digital input  
using a suitable 75screened cable.  
uSb connection  
Insert USB flash memory  
devices here. USB memory can  
be used to save downloaded  
content. e BDP100 can also  
play certain digital files stored  
on USB memory drives (see  
page E-8).  
CAUTION: Never connect  
the digital output socket to a  
conventional audio input.  
composite video output  
12V trigger input  
Connect this output to your  
display if the display does not  
support any other connection  
types.  
is socket allows the BDP100 to be switched  
in and out of stand-by mode by an amplifier  
(or another item of AV equipment) with a  
12V TRIg OuT function. See page E-4.  
Power inlet  
Connect the correct  
mains cable here.  
optical digital output  
RS232  
Use this socket if you are  
using an AV receiver with an  
optical digital audio input.  
is connection allows for remote  
control from a third-party home  
automation system or computer.  
network connection  
Connect this socket to a port on your  
network router using an Ethernet  
patch cable (see page E-9). An internet  
connection enables interactive  
content for BD-Live discs (for setup  
details see network” on page E-22).  
See page E-4 for more information.  
Zone 2 audio output  
Use this analogue output to  
provide audio for use in your  
AV receiver’s Zone 2. It can also  
be used to connect a recording  
device or headphone amplifier.  
Remote in  
is allows remote-control signals  
to be received by the BDP100  
if the remote sensor is covered  
(or otherwise not ‘visible’ to the  
remote-control).  
HdMi digital video output  
Connect this output to your display  
or AV receiver if available for the best  
digital video and audio connection  
(see. page E-7 for details).  
component video output  
If your display does not support  
HDMI but has a component input,  
connect it to this video output.  
See page E-4 for more information.  
e-5  
Making video connections  
Making audio connections  
e BDP100 offers a number of alternatives for connecting audio. e connection type to use depends on the rest of  
your system; chose the type most appropriate to your amplifier.  
To view the pictures from the BD player you need to connect one of its video outputs to your display device (TV,  
monitor, projector, etc.) or AV receiver (such as the Arcam AVr600).  
e BDP100 has three video output options, described below. You need only use one type of video from the list;  
choose a type that your display device or AV receiver supports. If your equipment does not support any of the above  
connection types then you will be unable to use it directly with the BDP100 and a video converter device may be  
required. In this case, please contact your dealer for further assistance.  
If you want to listen to audio through...  
...we recommend the following:  
Your television  
<
How you listen to audio through your TV depends on the inputs it has and your  
video connection:  
AV receivers and other video processing devices may be connected between the BDP100 and your display. Ensure  
that all the equipment supports the type of video signal you intend to use. For instructions on how to connect AV  
equipment, consult the manual for that equipment.  
HDMI: If you are using an HDMI connection (not DVI), this will carry both  
audio and video. no further connection is required.  
<
Digital Audio (Coaxial or Optical): If your TV has Digital Audio inputs on  
Coaxial or Optical connectors, connect the appropriate digital audio lead  
between the TV input and the appropriate BDP100 digital output. Do not  
make a connection between the BDP100 and a TVs Digital Audio output.  
<
HDMI DIgITaL VIDEO  
Stereo phono: If your TV has stereo phono inputs, follow the instructions  
<
e HDMI connector offers uncompressed digital video and audio transmission between  
the BDP100 and the display device, and provides the highest quality output. generally, it  
is also the easiest connection type to configure.  
below for a stereo amplifier.  
Your stereo amplifier  
<
<
To use this video connection, you will require a HDMI or HDMI/DVI cable between the  
BDP100 and your display device or receiver. See page E-7 for further details.  
If you wish to listen to audio from your player through a stereo amplifier, then use the  
stereo analogue outputs. ese outputs provide a stereo down-mix of the source material.  
Using a stereo phono cable of a suitable length, connect the outputs labeled zONE 1 auDIO to  
the leſt and right inputs (respectively) for DVD or CD on your amplifier.  
Your surround-sound receiver  
Connect the HDMI output to your receiver (for audio and video) if the receiver supports  
audio over HDMI. e HDMI connection supports all possible audio formats including  
Dolby TrueHD, DTS Master Audio and multichannel PCM.  
COMPONENT VIDEO  
Use three 75Ω phono cables to connect the Component Y, Pb, Pr outputs of the BD  
player to the Y, Pb, Pr inputs of the display device. Ensure that the cables are suitable for  
video use and that they are approximately the same length.  
If your receiver does not support HDMI audio, connect one of the Digital Audio outputs  
(Optical or Coaxial) to the ‘Blu-ray, ‘BD’ or ‘DVD’ input of your receiver. ese digital  
outputs provide PCM, Dolby Digital, DTS or MPEg multi-channel audio, depending on  
the source material. e BDP100 can also be set to re-encode all audio to DTS (“Bitstream  
Mixed”) (see Audio” on page E-21). is option provides the best surround sound quality for  
Digital Audio connections.  
If your television is capable of accepting a progressively scanned (de-interlaced) video  
signal, you may wish to use the progressive video output from the BDP100. If you are  
unsure whether your display device can accept progressive video, please refer to its  
instruction manual or consult your dealer.  
You may also wish to connect the stereo analogue audio outputs to the CD input on your  
receiver, for listening to CDs. is will allow the BDP100s audiophile digital-to-analogue  
circuitry to be utilised, for the best stereo sound quality.  
COMPOSITE VIDEO  
using two video connections simultaneously  
If your display device offers only a composite input (sometimes labelled CVBS or just  
‘video’), connect this to the COMPOSITE video output of the BD player using a 75Ω phono  
cable suitable for video use. note that a composite video connection gives the lowest-  
quality output; if your display device supports other video connection types, we advise  
that those are used instead.  
It is possible to use two video connections simultaneously (routing one connection to a  
second room or display, for example). If you wish to do this, please read these notes:  
e Composite video output is always active.  
It carries interlaced output at all times.  
<
<
<
e Component video output is always active.  
It can be set to carry either interlaced or progressive-scan output.  
e HDMI output is active only if a compatible display is detected by the BDP100.  
It can be set to carry either interlaced, progressive-scan or high-definition output.  
e-6  
Troubleshooting HdMi  
Problems with video  
The HdMi interface  
If you have a HDMI- or DVI-equipped monitor or  
display, you can connect it to the BDP100 using a HDMI  
cable. e HDMI connector carries uncompressed  
digital video, as well as digital audio.  
Problems with audio  
e type of audio provided by the HDMI connector  
depends on the configuration of the BDP100 (see  
AudioSetuponpageE-21).Chooseasettingaccording  
to the capabilities of your audio system. note that  
pure DVI devices (connections requiring a HDMI to  
DVI converter cable) do not support audio via this  
connection.  
No video (blank screen)  
Check that the HDMI cable is connected correctly at  
<
both ends. If an HDMI-equipped A/V receiver is in  
use, try connecting the BDP100 directly to the display  
device, in order to isolate where the fault may lie.  
about HdMi  
HDMI (High Definition Multimedia Interface) supports  
both video and audio on a single digital connection  
for use with Blu-ray Disc players, digital TV, set-top  
boxes, and other AV devices. HDMI was developed to  
combine the technologies of High-bandwidth Digital  
Content Protection (HDCP) and the Digital Visual  
Interface (DVI) in one specification, with the addition  
of transmission of digital audio information; HDCP is  
used to protect digital content transmitted to DVI-  
compliant displays.  
Check that the display device is set to display the  
HDMI input (i.e., has not been set to some other  
video input, instead).  
<
<
<
<
Check that the HDMI input of the receiver and/or  
display device is enabled. See the user handbook of  
the connected device for details on doing this.  
Using an alternative video display device (e.g.,  
connected via the composite video out), check that  
video is output.  
HDMI has the capability to support standard or  
high-definition video, together with stereo or multi-  
channel surround-sound audio. HDMI features include  
uncompressed digital video, one connector (instead of  
several cables and connectors), and communication  
between the AV source and AV devices.  
Consult the user handbook of the display device to  
ensure that it can handle the output formats provided  
by the BDP100. e BDP100 can provide the  
following:  
720 x 480p (nTSC progressive scan)  
720(1440) x 480i (nTSC interlaced)  
720 x 576p (PAL progressive scan)  
720(1440) x 576i (PAL interlaced)  
1280 x 720p  
1920 x 1080i  
1920 x 1080p  
connecting using HdMi  
Use a HDMI cable to connect the HDMI socket on  
this player to a HDMI socket on a compatible display  
device or receiver. e arrow on the cable connector  
body should be face up for correct alignment with  
the connector on the BDP100. If the BDP100 video  
resolution has been configured to ‘HDMI Auto, then the  
BDP100 will configure its video output automatically to  
match the capabilities of the attached HDMI device.  
At least one of these standards must be supported by  
the connected device in order for it to work with the  
BDP100.  
No video (random noise)  
random noise will be displayed if the content-protection  
algorithm fails to authenticate the attached device. is will  
occur, for example, if a DVI device that does not support  
HDCP (such as a computer monitor) is connected to the  
BDP100.  
NOTE: A HDMI connection can be made only with  
HDMI or DVI-equipped components compatible  
with both DVI and HDCP. note that if you choose  
to connect to a DVI device, you will need an adaptor  
(HDMI to DVI) to do so; a DVI/HDCP connection,  
however, does not support audio signals.  
To attempt to isolate this problem, remove all discs from the  
BDP100, then power-off both the BDP100 and the connected  
display device. Switch the display device on, then the BDP100  
– at this point, the idle logo of the BDP100 should be shown on  
the display device. If this is not the case, please check the items  
listed above for a blank screen.  
If you require further information on the  
possibilities for connecting your BDP100 to your  
DVI/HDMI equipped display device, please contact  
your Arcam dealer.  
If the noise appears when a copy-protected disc (Blu-ray/DVD)  
is played, then it is the authentication that is failing. Please  
contact your dealer for further information.  
e-7  
Playable files  
Region coding  
NOTE  
<
e player supports the following file types:  
Blu-ray Disc players and Blu-ray or DVD Video discs  
are assigned region codes according to the region in  
which they are sold. If the region codes do not match,  
the disc will not play.  
Only BD-rE/-r, DVD-r/-rW and  
CD-r/-rW discs recorded with UDF or  
ISO9660 format can be played back.  
is unit supports Ver 2.0 BD-rOM, Ver 3.0  
BD-rE and Ver 2.0 BD-r.  
Unfinalized BD-rE/-r, DVD-r/-rW and  
CD-r/-rW discs cannot be played back.  
Some 8 cm BD-rEs/8 cm BD-rs cannot be  
played on this unit.  
When a BD-Java title is played, loading may  
take longer than a normal title, and some  
functions may perform slowly.  
When an Audio CD recorded in DTS-ES  
or Dolby Digital EX is played, noise may be  
heard.  
<
MP3 (.mp3”)  
Sample rate: 44.1kHz, 48kHz  
Bit rate: Up to 320kbps.  
disc & file  
formats  
<
<
<
<
ID3 tags are not supported.  
MP3i and MP3 Pro are not supported.  
WMA (.wma”)  
Sample rate: 44.1kHz, 48kHz  
Bit rate: Up to 192kbps.  
Blu-ray Disc Area  
region code  
A
north America, Central America,  
South America, Korea, Japan, Taiwan,  
Hong Kong and South East Asia  
<
<
B
Europe, greenland, French territories,  
Middle East, Africa, Australia and  
new Zealand  
WMA tags are not supported.  
JPEG (.jpg, .jpeg”)  
Maximum resolution : 4,272x2,848 pixels.  
JPEg format images stored in progressive format  
cannot be played back.  
<
Playable discs  
e player supports the following disc types:  
C
India, China, russia, Central and  
South Asia  
A + B + C All areas  
<
<
AVI (.avi”)  
Playable codec : Xvid  
Maximum size of image : 1920 x 1080@30 fps  
WMV (.wmv”)  
Blu-ray Disc  
DVD region Area  
code  
Unplayable discs  
Any disc type not listed is not supported by the  
BDP100. Do not attempt to play an unsupported  
disc.  
1
2
north America  
Europe, Japan, Middle East, Egypt,  
South Africa, greenland  
Playable codec : WMV9  
Maximum size of image : 1920 x 1080@30 fps  
DVD-Video  
DVD-r  
Some BD-rE/BD-r, DVD-rWs/DVD-rs or  
CD-rs/CDrWs cannot be played due to incomplete  
disc finalization, poor recording quality or physical  
condition of the disc, incompatible characteristics of  
the recording device or authoring soſtware, etc. Try  
recording the disc at a lower speed, or try a different  
brand of media.  
3
4
Taiwan, Korea, the Philippines,  
Indonesia, Hong Kong  
Mexico, South America, Central  
America, Australia, new Zealand,  
Pacific Islands, Caribbean  
5
russia, Eastern Europe, India,  
most of Africa, north Korea, Mongolia  
See the operating instructions supplied with your  
recording device or soſtware for more information.  
6
China  
DVD-rW  
CD-Audio  
CD-r  
All  
All areas  
NOTE  
Symbols indicating disc will play in north America:  
Blu-ray Discs: DVDs:  
<
Characters except A~Z, a~z, 0~9, “ - “  
may be not be displayed.  
<
is unit supports multi-session discs. Some  
multisession discs may take a long time to  
load and some may not be loaded at all.  
<
<
For some files, it may not be possible to use  
certain functions during playback.  
It may not be possible to play some files, even  
if they have the extension of a file playable on  
this player.  
Symbols indicating disc will play in Europe:  
Blu-ray Discs: DVDs:  
CD-rW  
<
Files protected by DrM (Digital rights  
Management) cannot be played.  
e-8  
network connection  
BD-Live discs can enable the downloading of extra  
content from the Internet. To enjoy on-line content,  
connect the network socket of the BDP100 to a LAn  
port on your network router using an Ethernet patch  
cable (available from a computer supplies retailer).  
Arcam BDP100  
A local network with Internet connection is required. If  
you do not connect to the Internet through a router (e.g.  
you connect a single computer directly), please contact  
your Internet Service Provider or an IT professional  
regarding setting up a home network.  
LAN  
Internet  
Router  
NOTE  
<
When the player is powered on with no  
network configured, a pop-up is shown  
on-screen with an option to press the RED  
function key on the remote control to access  
network settings. Pressing RED will navigate  
directly to the network Settings menu. Please  
refer to page E-22 for details.  
USB ꢀash drive  
<
remember to press the  
key followed by  
S
in order to access the red button.  
u
uSb connection  
USB memory devices (flash drives) can be used for  
media playback and are necessary for storage of  
downloaded BD-Live content. To enjoy BD-Live  
content, the following specification is recommended:  
Capacity 2gB  
Formatted FAT32  
USB2.0 high speed (480Mbps)  
Connect the USB device to the USB socket on the rear  
of the unit.  
e-9  
basic  
operation  
ULTRAH GHPERFORMANCE24-BITDAC  
Loading a disc  
Press on the front panel (or  
and place the disc on the tray, with the playback side  
facing down (some discs are double sided, in which case  
the side labelled ‘side Ashould face up to play side A).  
Fast play  
Press or  
introduction  
NOTE  
/
on the handset)  
on the front-panel or remote control to  
< 1  
‘Basic use’ explains how to play a Blu-ray Disc (BD),  
DVD, CD or other type of disc. note that it may be  
necessary to configure your player correctly for your  
system before optimum – or any – playback can be  
achieved. Player configuration is described beginning  
on page E-20.  
8 7  
1
When you press a button, if the unit does not accept  
its operation, appears on the TV screen.  
play fast forwards or backwards. e following speeds  
for fast playback are available: x2, x4, x8, x16, x32, x64  
and x128 (depending on disc type). Press the button  
repeatedly to cycle through the different speeds. To  
resume normal playback speed, press PLaY.  
Operations are occasionally unacceptable even if  
is not displayed.  
Press  
/
on the front panel to close the tray. e disc  
< 1  
loads aſter a pause of a few seconds.  
Invalid operation may occur as expected if :  
More sophisticated features – such as special playback  
modes and programming jumps and playback sequences  
– are described in the “advanced operation” section,  
later in this handbook.  
<
e region codes of the unit is different from  
that of the disc and playback will not be  
allowed.  
e parental control is set to prevent  
operation.  
(For details, refer to "Parental Control" on  
page E-21.)  
BD/DVD Video operations and functions  
may be different from the explanations in  
this manual and some operations may be  
prohibited due to disc manufacturer’s settings.  
Skipping chapters/tracks  
To skip chapters (or tracks on a CD), press or  
Playing a disc  
.
/ 0  
A disc may take some time to load once the tray is  
closed. When the ‘Optical Disc Autoplay’ setting is set  
to On (default setting), playback will automatically start.  
(For details, refer to “Optical Disc AutoPlay” on page  
page E-22).  
When skipping back, the first button press takes you to  
the beginning of the current chapter. Pressing the button  
again takes you to the start of the previous chapter.  
<
Switching on  
Switch the unit on by pressing the POWER button. e  
status LED glows green when the unit is powered up and  
red when in stand-by mode. e remote control is used  
to enter and exit standby mode. If the POWER button is  
pressed (or power is removed) whilst in standby, the  
unit will enter standby mode when power is re-applied.  
Pausing playback  
If Autoplay is not set, the player’s Main Menu will  
appear on your TV. Use the cursor keys to select the  
disc, then press  
<
Press  
/
on the front panel or on the remote  
4 ;  
;
control to pause playback. To resume playback, press  
on the front panel or on the handset.  
/
4
to start playback.  
O
;
4
Some titles begin by displaying a menu. Select the menu  
item ‘Play movie’ (or similar) using the cursor pad, then  
press OK to start playback.  
Stopping playback  
note that the remote control sensor is located on the  
right-hand side of the display window. Do not obstruct  
this or the remote control will not work.  
Press the  
/
button on the front panel or on the  
< 1  
<
For discs that do not play automatically, press  
the front panel or press on the remote control.  
/
on  
4 ;  
remote control to stop playback.  
4
When playing a BD/DVD, pressing once performs  
<
a ‘resume stop. If you now press , playback resumes  
4
from the point it was stopped.  
If you press  
/
on the front panel or  
on the remote  
< 1  
<
control twice, this is a ‘complete stop, and playback  
resumes from the beginning of the disc.  
e-10  
remote  
control  
e BDP100 is supplied with the Cr104 universal  
remote control.  
notes on batteries:  
using the remote control  
Please keep in mind the following when using the  
remote control:  
inserting batteries into the  
Incorrect use of batteries can result in hazards  
<
such as leakage and bursting.  
remote control  
Do not mix old and new batteries together.  
<
<
<
Ensure there are no obstacles between the  
remote control and the remote sensor on the  
front panel. e remote has a range of about 7  
metres. (If the remote sensor is obscured, the  
Ir in remote control input jack on the rear  
panel is available. Please consult your dealer  
for further information.)  
Do not use non-identical batteries together –  
although they may look similar, different batteries  
may have different voltages.  
Ensure the plus (+) and minus (-) ends of each  
battery match the indications in the battery  
compartment.  
<
remove batteries from equipment that is not  
<
<
<
<
remote operation may become unreliable if  
strong sunlight or fluorescent light is shining  
on the remote sensor of the unit.  
replace the batteries when you notice a  
reduction in the operating range of the  
remote control.  
1. Open the battery compartment by pressing  
the button on the back of the handset.  
going to be used for a month or more.  
When disposing of used batteries, please comply  
with governmental or local regulations that apply  
in your country or area.  
2. Insert four AAAbatteries into the battery  
compartment – two facing the top of the unit,  
and two facing the end, as in the diagram.  
3. Lower the end cap onto the plastic locating  
plate in the handset. is acts as a hinge, and  
you can now push the end cap firmly into its  
locked position with a click.  
e-11  
controlling the bdP100  
DISP (display)  
On/Stand-by  
Press to cycle through the front panel displays  
brightness options (dim to bright, off).  
is allows the BDP100 to be put into and taken out of  
stand-by remotely.  
e Cr104 is a sophisticated ‘universal’ remote control  
that can control up to eight devices – including the  
BDP100. As it’s a ‘learning’ remote, it can copy almost  
any function from an existing single-device remote.  
You can also program the Cr104 to issue a sequence of  
commands (‘macros’) from a single button press.  
Numeric keys  
Source selection and handset configuration  
Used for data entry. Also gives direct access to  
individual tracks on audio CDs.  
BD  
BD input/BD controls  
Select the source key first  
SaT  
Satellite decoder input/SAT controls  
remember to select a source key before pressing  
command buttons – commands vary depending on the  
source selected.  
aV  
Television (sound) input/AV controls  
radio tuner input/TUn controls  
Arcam amplifier  
Personal Video recorder input/controls  
Video Cassette recorder input/controls  
CD player input/CD controls  
RND  
TuN  
Toggles random (‘shuffle’) play of chapters/tracks on  
and off.  
aMP  
T
DISP  
RND  
iPOD  
PVR  
Press SHIFT followed by RND to cycle through repeat play  
options (chapter, title, disc, etc.).  
To operate the BDP100 from the remote, first press the  
BD source button.  
VCR  
SHIFT  
STATUS  
CD  
Press the relevant button once to select input and  
reconfigure the handset.  
SAT  
PVR  
AV  
STaTuS  
TUN  
CD  
SAT  
PVR  
AV  
BD  
TUN  
Toggles the disc information display.  
Press and hold the button until the power LED blinks  
once if you wish to reconfigure the handset without  
changing the input.  
VCR  
VCR  
AMP  
Press SHIFT followed by STaTuS to activate or deactivate  
24p mode (supported discs and TVs only).  
AMP  
CD  
Navigation buttons  
Arrow buttons allow navigation around the settings  
menus on the BDP100 and disc menus.  
MENu  
Confirm a selection by pressing OK.  
Activates the BD ‘popup’ menu or the DVD disc menu.  
MODE  
RTN  
MODE  
MENU  
is button activates the Picture-in-Picture Secondary  
Video function, where available.  
navigates to the previous menu.  
RTN  
0/  
Press to skip backwards to the previous track( ) or  
MuTE  
0
Press once to mute an Arcam amplifier. Press again (or  
use +/volume) to un-mute.  
forwards to the next track ( ).  
/
U
VOLuME +/–  
Playback control  
SRCH  
Adjusts the volume of a compatible amplifier.  
Pause ( ), Play ( ) and Stop ( ). SHIFT+Pause  
;
4
<
activates slow playback.  
SETUP  
TITLE  
AUDIO  
SUBT  
OPEN  
Opens and closes the disc tray  
advanced controls  
ese buttons are described on the next page.  
SETuP  
23425  
CR104  
Press SETuP to access the system settings menu.  
e-12  
advanced controls  
Transport control buttons  
Fast rewind.  
7
Starts playback.  
4
Pause playback. Press  
to resume playback.  
;
4
NOTE  
When paused, pressing advances one frame.  
;
Many of these controls are labelled according  
to the functions assigned to other device  
SHIFT + activates slow motion playback.  
;
Fast forward.  
modes. For example, the  
key will activate  
8
8
1
<
the bass control of an A/V receiver when the  
Open / Close the disc tray.  
remote is in aMP mode.  
Stop playback  
Cycles through different camera angles, if present on the disc.  
=
RED/gREEN/YELLOW/BLuE  
e colour-coded buttons RED, gREEN, YELLOW and BLuE  
provide interactive controls for Blu-ray Discs and some  
player functions and will be displayed on-screen. ey  
are accessed by first pressing SHIFT followed immediately  
by the button required. eir function depends on the  
disc and the part of the disc being viewed.  
aNgLE  
U
Displays Angle menu, to allow selection of  
different camera angles, if present on the disc.  
SRCH  
V
F V  
SETUP  
TITLE  
AUDIO  
SUBT  
SETuP  
SRCH  
Ensure no disc is playing and press SETuP to  
access the ‘Settings’ menu.  
Displays Search menu with Time, Title and  
Track options.  
auDIO  
Some discs offer the facility to select different  
audio tracks. Press auDIO to access a menu  
that allows selection of the available tracks. See  
“Soundtrack Selection” on page E-16.  
TITLE  
SuBT  
Press TITLE to access the DVD’s ‘Title’ menu (a  
feature that only applies to multi-title discs) or  
to access the main menu if a Blu-ray Disc.  
Cycles through the available subtitle languages,  
including ‘O. Some discs force subtitles on,  
overriding any set up preferences.  
e-13  
In aV mode issues the TV ‘channel down’ command.  
0
useful information  
device Mode / Source keys  
The cR104 complies with Part 15 of the  
e Cr104 remains in the last selected Device Mode  
so it is not necessary to press a Device Mode key before  
every command key if all you are doing is playing or  
skipping tracks on a CD, for example.  
Fcc rules  
As the Cr104 can control your BDP100, AVr500,  
AVr600 or AV888 as well as a range of other equipment,  
many of the buttons have more than one function  
depending on the ‘device mode’ selected on the remote  
control.  
backlight  
is equipment has been tested and found to  
comply with the limits for a class B digital device,  
pursuant to part 15 of the FCC rules. ese limits  
are designed to provide a reasonable protection  
against harmful interference in a residential  
installation. is equipment generates, uses, and can  
radiated radio frequency energy and if not installed  
and used in accordance with the instructions,  
may cause harmful interference to radio  
communications. However, there is no guarantee  
that interference will not occur in a particular  
installation. If this equipment does cause harmful  
interference to radio or television reception, which  
can be determined by turning the equipment off  
and on, the user is encouraged to try to correct  
the interference by one or more of the following  
measures:  
A blue backlight comes on for five seconds whenever  
a key is pressed. is helps you use the handset in  
subdued lighting conditions. It may be possible to hear a  
quiet tone being emitted from the remote control when  
the backlight is on. is is perfectly normal.  
navigation keys  
e Device Mode keys (shown below) select the source  
on the AVr500/AVr600/AV888. If one of these keys is  
pressed briefly, a command is transmitted to change the  
source on the unit. Also the functionality of the remote  
control changes to operate the selected source device. It’s  
like having eight different remotes in your hand!  
e navigation keys steer the cursor in Setup menus or  
on-screen menus. ey also replicate the  
Power led blinks  
Short blinks indicate a valid key press.  
Multiple short blinks convey information (such as a  
device code) or signal the beginning and successful  
completion of a programming sequence.  
navigation functions of original remotes  
OK  
supplied with other home entertainment  
devices in your system.  
confirms a setting.  
O
Volume control  
SAT  
AV  
Long blinks indicate an invalid key press or entry.  
TUN  
CD  
D
By default, the Cr104 is set up so that the volume  
control buttons always control the volume of an Arcam  
amplifier or receiver, regardless of which Device Mode  
the remote is currently set for. is is known as volume  
‘punch through.  
e symbol ‘ ’ is used in the manual to indicate a  
*
power LED blink.  
PVR  
VCR  
AMP  
Timeouts and unassigned keys  
Time out – Aſter 10 seconds the Cr104 exits the  
programming state and returns to normal operation.  
Stuck key timeout – Aſter any key is pressed  
continuously for 30 seconds, the Cr104 stops sending  
Ir transmission to conserve battery life. e Cr104  
remains off until all keys are released.  
reorient or relocate the receiving antenna.  
For example, if you are listening to a CD, you will  
probably have the Cr104 in CD Device Mode to control  
the CD player. You can use the volume controls on  
the remote directly to adjust the volume of an Arcam  
BD  
BDP100 Blu-ray player  
Satellite set-top box  
Increase the separation between the equipment and  
receiver.  
SaT  
aV  
Connect the equipment into an outlet or a circuit  
different from that to which the receiver is  
connected.  
Audio-visual sound input (use with TV)  
DAB, Sirius, FM or AM tuner  
amplifier without first having to press  
to put the  
A
TuN  
aMP  
remote into aMP Device Mode. e volume buttons  
‘punch through’ the CD Device Mode on the remote to  
the aMP Device Mode. Volume ‘punch through’ can be  
disabled individually for any Device Mode if desired.  
Unassigned keys – the Cr104 ignores any unassigned  
key presses for a particular Device Mode and does not  
transmit Ir.  
Controls the amplifier and setup features  
of the AVr500/AVr600 and AV888  
Consult the dealer or an experienced radio/TV  
technician for help.  
PVR  
Personal Video recorder (or Digital  
Video recorder)  
low voltage indicator  
When the batteries are running down, the Ir transmit  
indicator on the Cr104 (the LED under the Power  
button) flashes five times whenever you press a button:  
VCR  
CD  
Video Cassette recorder  
Compact Disc player  
* * * * *  
If you press and hold a Device Mode key for about four  
seconds, you change the Device Mode of the Cr104  
without changing the signal source on the AVr500/  
If this happens, please fit four new AAA alkaline  
batteries as soon as possible.  
AVr600/AV888. is can also be done by pressing  
S
followed by a Device Mode key (within two seconds).  
ese two methods allow you to change which device  
the Cr104 controls without also changing the AVr500/  
AVr600/AV888 source, allowing uninterrupted  
listening.  
Each Device Mode changes the behaviour of many  
of the Cr104 keys to control the source device  
appropriately. For example:  
In CD mode plays the previous CD track.  
0
e-14  
controlling other devices  
code blink-back  
9. Important! Write your device code down on the  
right hand side of the page so you can remember  
it if you ever reset the Cr104.  
Method 1 (direct code setup)  
Method 2 (library search)  
is section describes another way to program the  
Cr104 to control third-party equipment.  
Library Search allows you to scan through all the  
codes contained in the Cr104s memory. It can take a  
lot longer than the previous method, so only use this  
method if:  
Once you have set up your Cr104, you can blink back  
your device set-up codes for future reference.  
is section describes the simplest (preferred) way to  
program the Cr104s Device Mode keys to control the  
non-Arcam devices in your system.  
example: To blink back your Television code  
What if i still can’t control my device?  
1. Press the appropriate Device Mode key (e.g.  
once.  
)
a
If your device doesn’t respond, repeat the above  
steps until one of the device codes listed for your  
brand works.  
<
SAT  
AV  
TUN  
CD  
D
2. Press and hold  
blinks twice  
until the red Power LED  
S
(It actually blinks once when  
* *  
Your device does not respond to the Cr104 aſter  
you have tried all the codes listed for your brand.  
If none of the codes listed for your brand operates  
your device, or if your brand is not listed at all, try  
the Library Search Method described in the next  
section.  
<
<
PVR  
VCR  
you press the key, then twice aſter about three  
seconds).  
AMP  
Your brand is not listed at all in the Device Code  
tables.  
<
3. Press  
. e  
key blinks twice.  
9 9 0  
P
Some of the modes are locked to Arcam operation  
but can be unlocked if required (see “Locking/  
Unlocking a specific Device Mode” on page E-28).  
<
<
4. For the first digit of your four-digit code, press 1  
and count all the red blinks. If there are no blinks,  
the digit is ‘0.  
notes:  
example: To search for a TV code  
1. Switch your TV on (not standby) and aim the  
Cr104 at it.  
Some codes are quite similar. If your device does  
not respond or is not functioning properly with  
one of the codes, try another code listed under  
your brand.  
<
mode only controls Arcam equipment.  
A
5. For the second, third and fourth digits, repeat the  
BD mode  
SAT mode  
AV mode  
Locked  
previous step, pressing  
,
, or  
in order.  
2. Press  
on your Cr104.  
2 3  
4
a
3. Press and hold  
twice.  
until the power LED blinks  
Unlocked  
Unlocked  
Locked  
now you have the four-digit code.  
S
If your device’s original remote control does not  
<
have a  
(POWEr) key, press  
instead of  
Make a note of the codes  
Write down the codes for your devices in the boxes  
below for future reference.  
P
$
P
4. Press  
. e power LED key blinks  
9 9 1  
TUn mode  
AUX mode  
VCr mode  
CD mode  
when setting up your device.  
twice:  
.
* *  
remember to press the corresponding device key  
<
<
Locked  
5. Press  
.
P
before operating your device.  
Unlocked  
Locked  
Device  
Code  
6. Aim the Cr104 at your Television and press  
[
Many TVs do not switch on pressing  
. Please  
P
repeatedly until your Television turns off.  
1
2
3
4
5
6
7
8
try pressing a number key (‘channel select’) to  
switch your TV back on.  
Here is a specific example of how to program the  
key to control an Addison television. e principles for  
controlling other devices are exactly the same.  
1. Make sure your device is switched on (not just on  
standby).  
2. Find the correct Device Code table (e.g. TV) for  
the type of device you want to control from the  
Cr104.  
Every time you press  
the Cr104 sends out a  
a
[
POWEr signal from the next code contained in its  
To search for the code for another device follow  
the instructions above, but press the appropriate  
<
memory. In the worst case, you may have to press this  
key up to 150 times, so patience is required! If you  
device key instead of  
during step 2.  
a
skip past a code, step back by pressing  
. remember  
]
to keep pointing the Cr104 at your Television while  
pressing this key.  
7. As soon as your television turns off, press  
to  
S
store the code.  
3. Find the row containing the codes for the  
manufacturer of your device (e.g. Addison) (page  
34). e most popular code is listed first.  
notes:  
Many TVs do not switch on by pressing  
. Try  
<
<
<
<
P
4. Press the appropriate Device Mode key (e.g.  
)
a
pressing a number key (‘channel select’) to switch  
your TV back on.  
If you cannot control your Television properly,  
please continue the Search Method: you may be  
using the wrong code.  
To search for the code for another device follow  
the instructions above, but press the appropriate  
Device Mode key instead of  
on the Cr104.  
5. Press and hold  
blinks twice:  
until the red Power LED  
S
(It actually blinks once when  
* *  
you press the key, then twice aſter about three  
seconds).  
6. Enter the first four-digit device code using the  
number keys. e power key blinks twice:  
.
during step 2.  
* *  
. If the  
a
7. Aim the Cr104 at the device and press  
If your device’s original remote control does not  
have a  
step 5.  
P
device switches off, the setup is complete.  
(STaNDBY) key, press  
instead during  
P
$
8. Turn your device back on and test all the Cr104s  
functions to ensure they are working properly.  
e-15  
advanced  
operation  
disc information  
Press STaTuS to display disc information on your TV  
screen. e information shown depends on the disc  
type.  
Menus  
Soundtrack Selection  
Subtitles  
Many of BD Video and DVD Video disc contains disc  
menu, top menu or pop-up menu which guides you  
through the available functions in the disc.  
Some discs contain multiple audio streams, such as  
a standard Dolby Digital 5.1 soundtrack and a high  
definition Dolby TrueHD 7.1 surround soundtrack.  
e audio stream can be changed during playback. e  
secondary audio (e.g. directors commentary) of Blu-ray  
Discs (if present) can also be changed (if alternatives are  
available).  
Some discs contain multiple subtitles. e subtitles can  
be changed during playback. Subtitles for the secondary  
video (e.g. directors commentary) of Blu-ray Discs  
(if present) can also be changed (if alternatives are  
available).  
e contents of menus and corresponding menu  
operations depend on the disc.  
For Audio CD:  
note: Subtitle language is changed using the settings  
menu. refer to page E-21.  
<
Disc Menu: Press  
the disc menu (‘Top Menu’) on  
the TV.  
to display  
t
Disc type Current track/Total track number  
Repeat playback  
mode  
note: Audio language is changed using the settings  
menu. refer to page E-21.  
Press  
to display the current subtitle information:  
b
<
Popup Menu: Press  
display the ‘Popup’ menu on the  
TV.  
to  
Track : 1 / 11  
U
Press  
to display the current audio stream  
Current subtitle/total number of subtitles  
Primary Subtitle  
o
information:  
0 : 00 : 23  
0 : 06 : 46  
Off  
Off  
P lay  
CD DA  
Use the remote control cursor keys to  
navigate the menus. Highlight an item  
Current audio stream/total number of streams  
Elapsed time  
(current track)  
Progress bar  
Total Random  
track playback  
time mode  
Playback  
mode  
and press  
to select it, otherwise,  
S ubtitle  
01 / 08 E NG  
Off  
O
Primary audio  
press the relevant menu key to exit the  
menu.  
P IP S ubtitle  
Audio  
01 / 04 E NG Dolby Digital  
Off  
Press STaTuS again to turn off this display.  
Secondary Subtitle  
P IP Audio  
Highlight either the Primary (Subtitle) or the Secondary  
(PIP Subtitle) subtitle selection using the  
buttons.  
Search  
/
' ,  
e  
button allows you to search for a specific title,  
Secondary audio  
h
chapter or track on the medium. Press  
to display  
h
Press  
to show alternate subtitles. Press  
/
to  
>
' ,  
NOTE  
the search box. Press  
type:  
repeatedly to select the search  
Highlight either the Primary (Audio) or the Secondary  
(PIP) audio stream selection using the  
buttons.  
h
highlight the desired subtitle then press  
to select it.  
O
If the secondary audio is not heard, set the Digital  
Output to PCM Stereo, Bitstream Mixed, PCM 5.1  
or PCM 7.1. (For details, refer to “Digital Output”  
on page E-21.)  
/
' ,  
Video Discs  
go to Title  
go to Chapter  
go to Time  
Use the remote control numeric buttons to enter the  
search data. Press  
location.  
Audio Discs  
go to Track  
Media Files  
go to File no.  
go to Time  
Press  
/
to show alternate audio streams. Press  
' ,  
>
to highlight the desired audio stream then  
When the primary and the secondary Audio  
streams are all switched, they will be mixed and  
heard together. Set the PIP Audio to Off to switch  
off the secondary audio stream.  
press  
to select it.  
O
to start playback from the selected  
O
e-16  
Picture in Picture (secondary video)  
Some Blu-ray discs include secondary video screens  
that can be played back as a small video overlaid in the  
Virtual Package  
bd-live  
bonusview & bd-live  
Bonusview and BD-Live are features of the Blu-ray Disc  
format.  
Bonusview provides Picture in Picture and Virtual  
Package functions for compatible discs. BD-Live discs  
additionally provide a variety of features via the Internet.  
Virtual Package/BD-LIVE data must be saved to a  
USB memory device connected to the BDP100. To  
enjoy these functions, connect a USB memory device  
(minimum 1 gB capacity, 2 gB or more recommended)  
supporting FAT 32 and USB 2.0 High Speed (480  
Mbit/s) to the USB connector. (For details, refer to “USB  
Connection” on page E-9.)  
Blu-ray discs supporting Virtual Package allow for extra  
content to be automatically transferred from the disc or  
from the Internet to USB storage for interactive viewing.  
Features available include secondary video and audio,  
subtitles and movie trailers.  
e BDP100 is compatible with BD-Live, allowing for a  
variety of functions when used with BD-Live compatible  
discs. BD-Live allows content such as the latest movie  
trailers and BD-J interactive games to be downloaded  
from the Internet to USB storage.  
corner of the screen. Press the  
button on the remote  
M
control to display the PiP menu:  
Available BD-Live functions are entirely dependant on  
the Blu-ray disc being played. Consult the disc manual  
for operational information.  
P IP  
Off  
NOTE  
<
Playback methods are disc-dependant — refer  
to the disc manual.  
NOTE  
<
Playback operations may require use of the  
colour-coded keys on the remote control. To  
access the colour key functions on the Cr104  
<
e BDP100 must have an active Internet  
connection to use BD-Live functions. refer  
to “network connection” on page E-9 and  
network” on page E-22  
Press  
to enter the PiP menu. Select a secondary video  
<
<
<
<
If there is insufficient storage space, the data will  
not be copied/downloaded. Delete unneeded  
contents or use a new USB memory device.  
If a USB memory device containing other  
contents (previously recorded) is used, the video  
and audio may not play back properly.  
If the USB memory device is disconnected from  
this unit during playback of Virtual Package/  
BD-LIVE contents, playback of the disc will stop.  
Some time may be required for the contents to  
load (read/write).  
>
stream using the remote control cursor keys  
/
.
remote control, press  
first.  
' ,  
S
Press  
to view the secondary video in PiP mode.  
O
<
<
BD-Live Internet access can be disabled using  
the BD-Live Internet access setting in the  
System menu. See “System” on page E-22  
NOTE  
Playback operations may require use of the  
colour-coded keys on the remote control. To  
access the colour key functions on the Cr104  
<
To listen to secondary audio or to display  
secondary subtitles, refer to “Soundtrack  
selection” or “Subtitles” on page E-16.  
remote control, press  
first.  
S
<
Secondary video may not be present for every  
scene of a disc. The feature is disc-dependant,  
please consult the disc manual for further  
details.  
NOTE  
<
It may not be possible to use the BD-LIVE  
functions if there is insufficient space on  
the USB memory device. In this case, refer  
to “Erase Blu-ray Storage?” on page E-22 for  
erasing the Virtual Package contents and  
the BD-LIVE contents in the USB memory  
device.  
<
<
Operation of USB memory devices is not  
guaranteed.  
Do not use a USB extension cable when  
connecting a USB memory device to the USB  
connector.  
e-17  
The Play Mode menu  
Use the  
/
cursor keys on the remote control to  
Playing files  
' ,  
highlight a menu item and press  
NOTE  
<
to select it.  
Use the  
/
cursor keys on the remote control to  
O
' ,  
Video and audio files can be played from USB media or  
You will only be able to browse the selected  
type of files (music, picture or video), even  
if a CD-r/CD-rW or a USB memory device  
contains a mix of music, picture and video  
files. To play a different file type, return to the  
main menu using the SETuP button.  
When there are playble files or folders within  
the selected media or folder, “Empty” will be  
displayed.  
highlight “Play Files” and press  
Mode menu:  
to show the Play  
Select “Play (file)” to play a single file, or select Add to  
Playlist” to add the file to the playlist. When the desired  
files have been added to the playlist, press  
remote control to go back to the Play menu.  
O
CD-r/rW discs. e following formats are supported:  
<
<
<
Video: AVI, WMV  
Image: JPg  
Audio: MP3, WMA  
on the  
<
The Play menu  
To play media files, insert the USB device or optical disc  
into the player. e main menu is displayed with music,  
video and/or picture file symbols:  
Please select Play mode  
Play All  
<
Play Selection  
Play Current Folder  
Cancel  
Mus ic  
2
item(s )  
A single file can be played or files can be added to a  
playlist in order to play a selection of files.  
Main Menu  
Video ꢀle  
P lay Files  
Highlight a file using the remote control cursor keys  
/
/
/
' , < >  
. Press  
to select the file.  
B rows e P ictures  
Now P laying  
O
System settings  
Select an option using the  
/
' ,  
cursor keys and  
Music ꢀle  
JPEG ꢀle  
If the file has not been added to the playlist, the  
following menu is displayed:  
press  
to select it.  
O
<
Play All: Plays all the files of the selected type on  
the disc or device.  
Play menu  
<
<
<
Play Selection: Plays all items added to the  
Add To P laylis t  
P lay (File)  
playlist.  
e items listed on the play menu vary according to the  
selected media and current status. When media is  
playing, press the STOP button to display the Play menu.  
Play Current Folder: Plays all the files of the  
selected type in the current folder.  
Cancel: return to Play menu.  
Use the  
/
cursor keys on the remote control to  
' ,  
highlight the media file type to play/view. Press  
select the file type. The 'Play' menu is displayed:  
to  
>
Select an option using the  
/
' ,  
cursor keys and  
When a play option is selected, the media will play and  
the “now Playing” information panel will be shown:  
press  
<
to select it.  
O
Main Menu: returns to the main menu.  
If the file has already been added to the playlist, the  
following menu is displayed:  
<
Play Files: navigates to the Play Mode menu.  
File : 1 / 1 Animals - When I dream. mp3  
Mus ic  
2
item(s )  
Title :  
<
Browse Pictures / Browse Music: Changes  
the file type to be played and navigates to the  
media device showing the file type selected.  
Artist :  
Album  
R emove from P laylis t  
P lay (File)  
0 : 00 : 28  
0 : 04 : 36  
Off  
Off  
P lay  
Main Menu  
P laylis t  
<
<
Add all to playlist: Adds all files to the playlist.  
Remove all from playlist: Clears all files from  
the playlist.  
P lay Files  
US B  
1
B rows e P ictures  
Now P laying  
<
<
Previous folder: navigates to the previous folder  
or menu.  
NOTE  
Now Playing: Displays the playback status for  
music files.  
<
When playing JPEg files, each file is displayed  
Play menu  
Media menu  
for a time interval. is can be adjusted by  
NOTE  
<
pressing SHIFT followed by  
on the remote  
&
“Play (File)” cannot be selected for JPEg  
images. Add the images to be viewed to the  
playlist in order to play a slideshow of images.  
e playlist is cleared whenever the USB  
device is removed or the optical disc is  
ejected.  
control, or by entering the Slideshow Effects  
menu, described opposite.  
To play all available files without making any selection,  
press to go to the Play menu, described below.  
<
<
e selectable play mode varies according to  
the operation status and the selected media,  
etc.  
<
To select particular files, use the  
/
cursor keys  
' ,  
on the remote control to highlight the media device  
to navigate in the Media menu. Press to select the  
>
media device and display the file and folder contents.  
e-18  
Play menu. Use the  
/
cursor keys on the remote  
advanced playback controls  
e following advanced controls are available during  
disc or file playback (depending on media type):  
' ,  
control to highlight “Browse Pictures” and press  
.
O
Select pictures and play them as described in “The Play  
menu” on page E-18. The JPEg pictures will be displayed  
whilst the music continues to play.  
S lide S how E ffects  
S lide S how Delay  
None  
Slow playback  
Press SHIFT followed by  
to activate slow motion  
5 s ec(s )  
&
playback. Press this button combination again to  
change the playback speed. Speeds of 1/2, 1/4 and 1/8 are  
available.  
Use the  
/
cursor keys on the remote control to  
' ,  
highlight a menu item and press  
Time interval  
to select it.  
>
When viewing JPEg picture slideshows, the time  
interval between pictures can be changed between 5, 10,  
<
Slide Show Effects: Use the  
/
cursor keys  
' ,  
NOTE  
<
15 and 30 seconds. Press SHIFT followed by  
to switch  
&
to select one of the following effects:  
< Horizontal Scroll  
< Fade  
When playing JPEg files and music  
simultaneously, the playback controls affect  
the JPEg file playback only.  
between different time intervals  
Rapid Playback  
Press  
or  
during playback to activate rapid  
< Shutter  
< none  
<
To control the music files:  
)
(
reverse or forward playback. Further button presses  
change the playback speed. Speeds of 2x, 4x, 8x, 16x,  
32x, 64x and 128x normal speed are available. Press  
1. Press the stop button  
to stop the  
#
Press  
to confirm the selection.  
JPEg slideshow and display the Play  
O
$
menu.  
to resume normal playback.  
2. Use the  
/
cursor keys on the  
<
Slide Show Delay: Use the  
to select the delay time between pictures:  
< 5 seconds  
/
cursor keys  
' ,  
' ,  
remote control to highlight “now  
Playing” and press . The playback  
displaying File information  
Press the STaTuS button to display the file information  
panel. e file information panel shows the following  
information:  
O
controls nowaffect music playback.  
< 2 seconds  
< 1 second  
< none  
< 10 seconds  
< 15 seconds  
< 30 seconds  
Current ꢀle/total ꢀle number  
File type  
Repeat playback mode  
Title  
File : 2 / 3  
0 : 01 : 59  
.. Love.Actually.DVDDiv...  
Press  
to confirm the selection.  
O
1 : 04 : 56  
Off  
Off  
P lay  
Playing music whilst viewing  
Random  
playback mode  
Elapsed time  
Progress bar  
pictures  
During the playback of music files,  
Playback  
mode  
Total playing time  
of current ꢀle  
press the  
button to display the  
O
Press status again to hide the file information panel.  
note that the file information panel is always shown  
when playing music files.  
Slideshow effects  
When viewing a JPEg picture slideshow, press the  
U
button to display the Slideshow Menu:  
e-19  
settings  
menus  
e Settings menus allow you to configure all aspects  
of your BDP100. e next few pages will go through  
the menu items and explain their function. e Settings  
menus may look daunting if you are new to setting up  
home cinema, but the majority of them need only be  
configured once when you first install the system.  
navigating the menus  
e BDP100 menus can be navigated by using the  
cursor (arrow) keys on the remote control.  
S ys tem  
1. To display the main menu, press the SETuP button.  
Dis play  
Network  
Info  
2. Use the  
and  
keys to navigate up and  
B
C
down the main section headings in the leſt-hand  
panel.  
e only way to view the Settings menus is on your  
display device (TV or projector) using the on-screen  
display (OSD) capability of the BDP100. To view the  
OSD for the initial setting up, connect any of the video  
outputs to your display device (or AV receiver connected  
to your display).  
HDMI S tatus  
C onnected  
720p  
NTS C  
HDMI Auto  
16:9 P illarbox  
Off  
3. Once you have the main section that you require  
HDMI P referred Format  
TV Type  
highlighted, use the key to enter the section.  
E
R es olution  
TV As pect  
Film Mode  
C olor Depth  
4. Use the  
and  
keys to navigate up and  
B
C
Dis play  
down the section settings in the right-hand panel.  
Some settings may be greyed out. ese are either  
for information only (e.g. incoming sampling  
frequency) or are not currently selectable (e.g.  
network IP address when DHCP is used).  
24 B it  
entering the settings menu  
To enter the settings menu, use the  
and  
cursor  
Audio  
L anguage  
P arental  
'
,
keys to highlight the ‘Settings’ option on the main menu.  
If the main menu is not currently displayed, press SETuP  
on the remote control to display it. note that during the  
playback of music, video or JPEg files further button  
presses may be required to exit the folder structure.  
5. Pressing > selects a setting to change it,  
6. Use the  
and  
keys to change the setting.  
B
C
7. Press OK to confirm the setting. go back to step 4  
to adjust the other settings in the current section.  
Press  
to enter the Settings menu.  
>
6. Press  
or RETuRN to go back to the previous  
<
screen, to select another section to adjust.  
unstable oSd menu or picture display?  
e default BDP100 output video resolution when first  
powered up out of the box has been chosen according  
to the national standard in the country wheso that most  
display devices can synchronise to the video signal  
automatically. is can be changed in the Video Outputs  
section of the Setup Menus.  
If the output resolution and frame rate is set to a setting  
your display device does not support, the picture  
may become unstable or may not display at all. If this  
happens, connect the BDP100 directly to your display  
using the composite video connection in order to see  
the menus. Once the correct video settings have been  
entered, a higher-quality connection can be used.  
e-20  
Digital Output – Sets the audio format output from the  
display  
NOTE  
<
language  
OSD – Set the language used for the On Screen Display  
(OSD).  
Menu – Set the language used for the Disc Menu and  
Pop-up Menu.  
HDMI, OPTICaL or COaxIaL DIgITaL OuT.  
1080/24p video signals can only be output  
<
<
<
<
Bitstream HD: Output the HD bitstream Blu-ray  
Disc soundtrack for decoding in your AV receiver  
(HDMI output only, requires compatible AV  
receiver).  
Bitstream Legacy: Output the relevant legacy  
format for the soundtrack. is option is suitab;e  
for older AV receivers that are not HD, HDMI  
Audio or DTS compatible.  
Bitstream Mixed: Convert all surround audio to  
DTS 5.1 surround format. is option gives the  
best quality for DTS-compatible AV receivers that  
are not HD or HDMI Audio compatible.  
PCM 7.1: Decodes all formats within the player  
and outputs PCM audio. Use this option for HD  
receivers that cannot decode all HD formats. e  
OPTICaL and COaxIaL digital outputs will output  
stereo PCM audio.  
TV Type – Set the video signal format. If the colour or  
picture quality of analogue video appears incorrect,  
change this setting. It should not need to be adjusted in  
normal use.  
using the HDMI connection.  
<
<
e connected equipment (AV receiver, TV/  
projector) must be 1080/24p compatible.  
e output resolution must be set to 1080p or  
HDMI Auto.  
<
NTSC: USA and Canada video standard.  
<
Auto: Sets the priority language of the disc.  
Audio – Set the language for the soundtrack.  
Auto: Sets the priority language of the disc.  
Subtitle – Set the language used for the subtitles.  
Off: Displays no subtitles.  
<
PAL: Europe, Australia and China video standard.  
Color Depth – Set the level of Deep Color processing  
applied to the HDMI video output.  
Resolution – Set the video resolution of the HDMI and  
COMPONENT VIDEO outputs.  
<
<
<
<
36-bit: Select to output 36-bit Deep Color signals  
<
<
<
<
<
HDMI Auto: Sets the TVs preferred resolution.  
1080p: Full HD progressive video.  
1080i: interlaced HD video.  
720p: progressive HD video.  
480p/576p: 480 lines (nTSC) or 576 lines (PAL)  
progressive video  
<
from the HDMI output.  
30-bit: Select to output 30-bit Deep Color signals  
from the HDMI output.  
24-bit: Select to output 24-bit standard color  
signals from the HDMI output (Deep Color off).  
NOTE  
<
e ability to select a particular language may  
depend on the disc played.  
<
480i/576i: 480 lines (nTSC) or 576 lines (PAL)  
Standard Definition interlaced video.  
NOTE  
<
<
<
PCM 5.1: As PCM 7.1 but any HD 7.1-format  
surround soudtracks will be converted to 5.1-  
format surround (HDMI output only).  
PCM Stereo: Decodes all formats within the  
player and outputs PCM audio. All surround-  
sound formats are converted to stereo on all audio  
output connections.  
e connected equipment (AV receiver, TV/  
projector) must be Deep Color compatible  
in order to use 30/36-bit Deep Color signals.  
refer to your TV & AV receiver user manual.  
All system HDMI interconnect cables must  
be Deep Color compatible in order to use  
30/36-bit Deep Color signals.  
If you experience a flickering or abnormal  
picture aſter changing the Deep Color  
setting, connect the unit using a Composite  
video cable and change the setting to a value  
supported by the display.  
Parental control  
NOTE  
Parental control settings can be engaged to prevent  
viewing of discs or scenes with material inappropriate  
for children. A 4-digit code is required to enable or  
disable Parental Control. Parental Control has various  
levels; according to the level set, a disc may be stopped  
or have certain scenes cut or substituted with alternative  
scenes, depending on the disc.  
<
e HDMI Auto setting may not set the best  
possible resolution. If you have a 1080p Full  
HD display, set the resolution to 1080p.  
<
<
<
For full details of output resolutions available  
at different outputs, refer to the table on page  
E-25.  
NOTE  
<
e signal at the HDMI output is also  
determined by the formats supported by the  
connected equipment.  
To activate Parental Control:  
1. Select the Parental Control menu:  
TV Aspect – Set the aspect ratio (shape) of your display.  
<
16:9 Wide: Use with widescreen TVs. 4:3 material  
will be zoomed to fit the screen.  
Settings  
Parental Control  
u
>
>
<
For full details of output formats, refer to the  
table on page E-25.  
2. If Parental Control is set to On, you must enter your  
PIn using the remote control numeric buttons.  
The default PIn is 3308.  
<
16:9 Pillarbox: Use with widescreen TVs. 4:3  
material will be displayed in full, with vertical  
black bars at the sides.  
audio  
<
<
4:3 Pan and Scan: Use with 4:3 non-widescreen  
TVs. 16:9 widescreen content will be displayed  
with the leſt- and right-hand sides of the image  
cropped to fit the screen (no black bars). e  
aspect ratio will be maintained (the image will not  
be stretched).  
4:3 Letterbox: Use with 4:3 non-widescreen TVs.  
16:9 widescreen content will be displayed with  
black bars at the top and bottom.  
P lease Input 4-Digit P arental P assword :  
Dynamic Range Control – Set whether to compress the  
dynamic range between the loudest and soſtest sounds  
when a Dolby Digital, Dolby Digital Plus or  
DolbyTrueHD audio is played back.  
PCM Downsampling – Set the maximum sample  
rate of audio output from the OPTICaL or COaxIaL  
DIgITaL OuT.  
P arental P assword  
<
96kHz: Output digital audio with a 96kHz sample  
rate (best quality).  
<
On: Turns on Dynamic range Control so that  
quiet sounds can be heard more easily.  
<
48kHz: Output digital audio with a 48kHz sample  
rate (most compatible).  
OK  
C ancel  
<
<
Off: Turns Dynamic range Control off.  
Auto: Allows coding embedded within a Dolby  
TrueHD soundtrack to set the dynamic range. For  
other soundtracks, responds the same as ‘On’.  
3. Once the Parental Control menu is accessed, press  
the cursor buttons on the remote to  
NOTE  
<
24p Mode – Enable or disable 24 frames-per-second  
video output (1080/24p).  
/
' ,  
If the connected equipment (e.g. AV receiver)  
does not support 96kHz, silence or loud noise  
may result from this setting. If this happens,  
set PCM Downsampling to 48kHz.  
select from the following items. Press  
an item.  
to select  
>
<
On: Select to output 24p signals from the HDMI  
output.  
<
Off: Disable 24p video output.  
e-21  
Parental Control – Set whether Parental Control is On  
Primary DNS – Press OK to set the IP address of your  
Primary DnS server. Use the cursors to navigate  
between segments and use the numeric keys on the  
remote control to enter the address. navigate to the  
on-screen OK button and press OK on the remote to  
save the setting.  
System  
network  
An active, configured Internet connection is required  
if you wish to use BD-Live websites and downloaded  
content. See page E-9 for physical connections.  
Most home networks will automatically configure  
the connection using DHCP. If your network is not  
configured automatically, you will need to know the  
following settings:  
or Off.  
<
Off: All discs are played back.  
Optical Disc Autoplay – controls whether an optical disc  
(e.g. Blu-ray Disc, DVD, CD) will play automatically  
aſter it has loaded.  
<
On: Disc palyback is restricted according to the  
Parental Level set in the following menu item.  
<
On: Optical discs will play automatically.  
Parental Level – Set the degree of disc restriction. e  
lower the value, the stricter the limitation.  
Secondary DNS – Press OK to set the IP address of  
your Secondary DnS server. Use the cursors to navigate  
between segments and use the numeric keys on the  
remote control to enter the address. navigate to the  
on-screen OK button and press OK on the remote to  
save the setting.  
<
Off: PLaY must be pressed to play a disc.  
<
<
<
<
<
<
1 [Kid Safe]: Suitable for children.  
2 [G]: general audience.  
3 [PG]: Parental guidance suggested.  
4 [PG-13]: Unsuitable for children under 13.  
5 [PG-R]: Parental guidance recommended.  
6 [R]: restricted; cinemas require children under  
the age of 17 to have an accompanying adult  
parent or guardian.  
BD-Live Internet access – sets restrictions on Internet  
access.  
IP Address  
Subnet Mask  
Gateway  
Primary DNS  
Secondary DNS  
<
<
<
<
<
<
<
<
Limit Access: Only allows Blu-ray discs with  
owner certification to access the Internet.  
Always Allow Access: All BD-Live discs are  
allowed access to BD-Live websites.  
Prohibit Access: Prohibit all BD-Live discs from  
accessing BD-Live websites.  
network Test  
Press OK to run a network test. is will also configure  
the network settings automatically if they have not been  
configured and if automatic configuration (DHCP) is  
supported by the network.  
Wired network  
Select and press OK to set the network connection  
parameters:  
<
<
7 [NC-17]: Cinemas do not admit anyone  
younger than 17 years old.  
NOTE  
8 [Adult]: Discs of any rating (Adult/general/  
Children) can be played back.  
<
e available on-line functions are disc-  
dependent.  
Link Status – Information only  
MAC Address – Information only  
<
<
refer to the BD-Live disc instructions for  
Parental Password – Press  
with this option  
>
IP Mode – Set whether the network settings are  
automatic or set manually.  
information about accessing on-line content.  
highlighted to enter a new password. Enter a new 4-digit  
code using the numeric buttons on the remote control,  
then navigate to the on-screen OK button using the  
remote control cursor keys, then press OK on the remote  
control. You will be prompted to re-enter the code for  
confirmation, repeating the process above.  
e BDP100 must be connected to the  
Off: Disables network functions.  
Internet and set up correctly to allow access  
to on-line content. See page E-9 for network  
connectionsandpageE-22fornetworksettings.  
<
Manual: Enter settings manually, for expert users.  
<
<
Dynamic: Allows the connected router or modem  
to configure the network settings automatically,  
using the network’s DHCP server. is setting  
should be used for the majority of home networks.  
BD-Live Storage – BD-Live content is stored in the  
attached USB memory device. is menu item displays  
the amount of USB memory remaining.  
Please enter a new Parental Control Password:  
e following settings are only available when IP Mode  
is set to Manual:  
P arental P assword  
Erase Blu-Ray Storage – Press OK with this item  
highlighted to erase the BD-Live content stored on the  
USB storage device.  
IP Address – Press OK to set the IP address assigned  
to your player by your network administrator. Use  
the cursors to navigate between segments and use the  
numeric keys on the remote control to enter the address.  
navigate to the on-screen OK button and press OK on  
the remote to save the setting.  
OK  
C ancel  
Screensaver duration –sets the duration of static image  
display before the screensaver is shown. e screensaver  
prevents screen damage due to burn-in of a static image.  
<
Off: Deactivates the screensaver function.  
<
5/10/20/30 minutes: sets the period of time  
that a static image can be displayed before the  
screensaver activates.  
Subnet Mask – Press OK to set the subnet mask of your  
network. Use the cursors to navigate between segments  
and use the numeric keys on the remote control to enter  
the subnet mask. navigate to the on-screen OK button  
and press OK on the remote to save the setting.  
NOTE  
<
e screensaver can be deactivated by  
Gateway – Press OK to set the IP address of your  
Internet gateway. Use the cursors to navigate between  
segments and use the numeric keys on the remote  
control to enter the address. navigate to the on-screen  
OK button and press OK on the remote to save the  
setting.  
pressing any button on the unit or remote.  
Reset Settings – Press OK with this item highlighted to  
reset all settings to factory defaults (except parental  
controls).  
e-22  
If a fault occurs, run through the table below before taking your unit for repair.  
trouble-  
shooting  
If the fault persists, attempt to solve it by switching the unit off and on again. If this fails to resolve the situation, consult your  
dealer. Under no circumstances should you repair the unit yourself as this will invalidate the guarantee!  
Problem  
Possible cause  
remedy  
no power  
• e AC input cord is disconnected.  
• Poor connection at AC wall outlet or the outlet is inactive.  
• e disc is loaded upside down.  
• Connect cord securely.  
• Check the outlet using a lamp or another appliance.  
reload the disc with the printed side up.  
• Use a playable disc.  
no playback  
• e disc is not playable.  
• e disc is dirty.  
• Clean the disc.  
• e recorded disc is not correctly finalized.  
• e parental level is not set correctly.  
• e symbol about invalid operation is displayed.  
• e disc is scratched, dirty, poorly recorded or unplayable.  
• Load a disc that is correctly finalized.  
• Set the parental level setting correctly. (refer to page E-21.)  
• Adjust the setting correctly.  
Malfunction  
• Press the POWEr switch to switch the power off, press the  
POWEr switch again and then unload the disc.  
no picture  
• e video cords are disconnected.  
• e incorrect selection of input source on the TV.  
• e disc is not playable.  
• Connect the cords correctly.  
• Select the input source correctly.  
• Use a playable disc.  
noisy or distorted picture  
• e unit is connected to a recording device directly and the  
copyguard function is activated.  
• Connect the unit so that the picture signal is  
transferred directly to the TV.  
• e disc is dirty.  
• Clean the disc.  
• It is in rapid advance or reverse playback, or in frame  
advance playback.  
• e resolution is not set correctly for video signals to be output form the  
COMPOnEnT and the HDMI OUTs.  
• e TV does not support HDCP.  
• e TV type of this unit is different from that of your TV or the disc.  
• Sometimes a small amount of picture distortion may  
appear. is is not a malfunction.  
• Set the resolution correctly. (refer to page E-21.)  
• is unit will not transfer the video signals via the HDMI  
connector to TV that does not support HDCP. is is not a  
malfunction.  
Abnormal picture or no picture  
• Set the TV type correctly. (refer to page E-21.)  
Slight pause of picture  
• e layer transition occurs during playback of DVD Videos, etc. recoded in  
dual-layer format.  
• Sometimes a slight pause may occur. is is not a malfunction.  
no sound  
• e audio cords are disconnected.  
• Connect the cords correctly.  
• e speakers are disconnected to the amplifier.  
• e incorrect selection of input source on the amplifier.  
• e disc is dirty.  
• Connect the speakers correctly.  
• Select the input source correctly.  
• Clean the disc.  
noisy or distorted sound  
• Poor connections.  
• Check the connections and connect all cords securely.  
• Check the connections and connect all cords securely.  
• Connect the USB memory device to this unit.  
• Set it to Always Allow Access” (refer to page E-22.)  
• Load a disc that supports BD-LIVE.  
• Set the network settings correctly. (refer to page E-22.)  
replace the batteries.  
BD-LIVE contents cannot be loaded  
• Poor connections between this unit and broadband router and/or modem.  
• e USB memory device is disconnected.  
• e BD-Live Internet Access is set to “Prohibit Access.  
• e BD disc does not support BD-LIVE.  
• e network settings are not set correctly.  
• Batteries are not loaded or exhausted.  
• e remote sensor is obstructed.  
remote control unit does not operate.  
remove the obstacle.  
e-23  
START  
audio  
& video  
output  
formats  
NO  
Do you use an AV receiver?  
Use “PCM Stereo”  
YES  
audio output format  
NO  
e audio output format available from the digital audio  
outputs depends on the soundtrack format being played,  
the audio output in use and the Digital Output setting  
in the Audio settings menu (Audio” on page E-21).e  
table opposite shows all possible combinations.  
NO  
NO  
YES  
YES  
NO  
Do you connect audio using  
HDMI?  
Does your receiver support  
the DTS audio format?  
Do you connect audio using  
Optical or Coaxial Digital?  
Use “Bitstream Legacy”  
Use the flowchart on this page to guide you to the  
correct setting for your home cinema setup.  
YES  
YES  
Use “Bitstream Mixed”  
Is your receiver HDMI1.3  
compatible (Dolby TrueHD/  
DTS HD)?  
YES  
NO  
NO  
Do you want to play back  
Secondary Audio from  
Blu-ray Discs?  
Do you have a 7.1-format  
surround sound  
Do you have a  
surround sound  
speaker system?  
Use “PCM Stereo”  
speaker system?  
NO  
YES  
YES  
Use “Bitstream HD”  
Use “PCM 7.1”  
Use “PCM 5.1”  
e-24  
Audio Format  
Dolby Digital  
Digital Output setting  
Bitstream HD  
Bitstream Legacy  
Bitstream Mixed  
PCM 7.1  
HDMI out  
Dolby Digital 5.1  
Dolby Digital 5.1  
DTS 5.1  
Optical/Coax out  
Dolby Digital 5.1  
Dolby Digital 5.1  
DTS 5.1  
PCM 5.1  
PCM Stereo  
PCM 5.1  
PCM 5.1  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
Bitstream HD  
Dolby Digital Plus /  
Dolby TrueHD  
Dolby Digital 5.1  
Bitstream Legacy  
Bitstream Mixed  
PCM 7.1  
PCM 5.1  
PCM Stereo  
Bitstream HD  
Dolby Digital 5.1  
DTS 5.1  
PCM 7.1  
PCM 5.1  
PCM Stereo  
DTS-HD High  
resolution Audio /  
DTS-HD Master Audio  
Dolby Digital 5.1  
DTS 5.1  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
Dolby Digital Plus /  
Dolby TrueHD  
Video output Resolution  
e following table shows the video output resolution  
at each video output for the different resolution settings  
(see “Display” on page E-21).  
DTS-HD High  
resolution Audio /  
DTS-HD Master Audio  
Bitstream Legacy  
Bitstream Mixed  
PCM 7.1  
DTS 5.1  
DTS 5.1  
PCM 7.1  
PCM 5.1  
PCM Stereo  
DTS 5.1  
DTS 5.1  
DTS 5.1  
PCM Stereo  
PCM Stereo  
PCM Stereo  
DTS 5.1  
resolution setting  
Video Outputs  
Component video out  
PCM 5.1  
Composite video out  
HDMI out  
nTSC  
Preferred  
1080p  
1080i  
720p  
PCM Stereo  
Bitstream HD  
Bitstream Legacy  
Bitstream Mixed  
PCM 7.1  
nTSC  
480i  
480i  
480i  
480i  
480i  
480i  
PAL  
576i  
576i  
576i  
576i  
576i  
576i  
nTSC  
1080i  
1080i  
1080i  
720p  
480p  
480i  
PAL  
1080i  
1080i  
1080i  
720p  
576p  
576i  
PAL  
Preferred  
1080p  
1080i  
720p  
DTS 5.1  
DTS 5.1  
HDMI Auto  
1080p  
1080i  
720p  
480p/576p  
480i/576i  
DTS 5.1  
PCM 5.1  
PCM 5.1  
PCM Stereo  
PCM 7.1  
PCM 7.1  
DTS 5.1  
PCM 7.1  
PCM 5.1  
PCM Stereo  
PCM Stereo  
PCM Stereo  
DTS 5.1  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
DTS 2.0  
DTS 5.1  
DTS  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
DTS 5.1  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
DTS 2.0  
PCM 5.1  
PCM Stereo  
Bitstream HD  
Bitstream Legacy  
Bitstream Mixed  
PCM 7.1  
480p  
480i  
576p  
576i  
LPCM 7.1 (48kHz /  
96kHz)  
PCM 5.1  
PCM Stereo  
Bitstream HD  
Bitstream Legacy  
Bitstream Mixed  
PCM 7.1  
NOTES:  
<
<
<
If the HDMI and Component video outputs are used simultaneously, the Component video  
will be output at standard definition (480i/576i resolution).  
Copy protected DVDs can only be output at standard definition over analogue video  
connections (component or composite).  
If the BDP100 is set to a resolution that your TV does not support, there may be no picture.  
If this happens, connect the Composite Video output to your TV. Select the appropriate  
video input on your TV to display the settings menu. Change the resolution to a value  
supported by your TV then change the connections back to the desired configuration.  
LPCM 5.1 192kHz  
PCM 5.1  
PCM Stereo  
Bitstream HD  
Bitstream Legacy  
Bitstream Mixed  
PCM 7.1  
<
e ‘HDMI Auto’ setting uses the resolution value that the TV requests. is may not be  
the best resolution. It is recommended to consult your TV documentation to discover the  
best resolution setting and to set this resolution manually.  
LPCM 2.0  
(44.1kHz / 48kHz)  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM Stereo  
PCM 5.1  
PCM Stereo  
e-25  
e original function of the Cr104 is restored.  
until the device key blinks twice:  
.
* *  
code learning  
9. To use the learned function on the Cr104, press  
the Device Mode key, followed by the function  
key.  
To delete a Shifted learned function:  
e Cr104 comes with a complete library of  
preprogrammed codes. Aſter you have set up the Cr104  
for your device, you may find that there are one or more  
functions on your original remote which do not have a  
place on the Cr104 keypad. For convenience, the Cr104  
offers a Code Learning feature that allows you to copy  
up to 16 functions from an original remote control onto  
the Cr104 keypad.  
To delete a Shiſted Learned function, press  
before  
S
you press the key to be deassigned (during step 4 above).  
In this example, youd press  
followed by  
customising  
the CR104  
To delete all learned functions within a  
a
(
given device Mode  
Shifted learning  
You can assign a learned function to a Cr104 key  
without sacrificing its original function.  
1. Press and hold  
until the power LED blinks  
S
twice:  
2. Press  
.
9 7 6  
* *  
– the power LED blinks twice:  
Before you start, make sure that:  
You can assign Shiſted Learning functions to any key  
.
* *  
e original remote control is working correctly.  
e remotes are not pointing at your device.  
e remotes have new batteries.  
e remotes are not in direct sunlight or under  
strong fluorescent lights.  
<
<
<
<
except for: Device Mode keys (e.g.  
keys ( to ).  
), , or number  
a S  
3. Press the appropriate Device Mode key twice.  
0
9
1. To assign a Shiſted Learning function, simply  
follow Code Learning steps in the previous  
section. During step 5, press  
once before you  
S
press the key to which you want to assign the  
learned function.  
Learned functions are mode-dependent: You could  
theoretically assign up to eight different functions  
to a single key (the Cr104 can handle a total of 16  
learned functions).  
2. To access the shiſted function, press  
the target key.  
and then  
S
important notes  
Once you start a Code Learning session, you have  
approximately 10 seconds to conduct each step.  
Any longer, and a timeout means that you’ll have  
to start the process again.  
e Learning feature is mode-specific – you can  
copy one feature per mode onto a key.  
e Cr104 can learn approximately 16 functions  
in total.  
To replace a learned function, simply assign a new  
one to the same key.  
Learned functions are retained when you change  
batteries.  
If Code Learning fails, try altering the distance  
between the two remotes; make sure that the light  
in the area is not too bright.  
<
example: To copy the‘text hold’ function  
from a TV remote onto the  
key of your  
(
cR104  
1. Place both remotes on a flat surface, 2 to 5cm  
<
<
<
<
<
apart, with the Ir ports facing each other.  
2. On the Cr104, press and hold  
until the power  
S
LED blinks twice:  
.
* *  
3. Press  
. e power LED blinks twice:  
9 7 5  
.
* *  
4. On the Cr104, press the device key that matches  
the ‘source’ device (e.g. if you’re learning a TV  
function, press  
).  
a
5. On the Cr104, press the key to which you want to  
assign the learned function (e.g.  
key blinks rapidly.  
). e device  
(
To delete a learned function  
6. On the original remote, press and hold the  
function key that you want to learn (e.g.  
1. Press and hold  
until the power LED blinks  
S
twice:  
.
* *  
TExT HOLD) until the Cr104 device key blinks  
2. Press  
. e power LED blinks twice: .  
9 7 6  
twice:  
.
* *  
3. Press a Device Mode key once. For example, if you  
want to delete one of your learned TV functions,  
7. If you want to learn other functions from the  
same source device, simply repeat steps 5 and 6  
pressing the next key you want to learn.  
press  
.
a
4. Press twice on the key you want to deassign. e  
handset blinks twice: to confirm.  
8. To exit Code Learning mode, press and hold  
S
* *  
e-26  
example: To deassign the Macro associated  
with the key  
creating Macros  
Volume punch-through  
Volume punch-through means that, no matter which  
Device Mode is selected, the Cr104 controls the  
AVr500, AVr600 or AV888 volume. You don’t need to  
key Mover  
h
You can program your Cr104 to issue a sequence of  
commands when you press a single key. Any sequence of  
commands you regularly use can be reduced to a single  
key press for your convenience.  
Sometimes you might find that a key you use a lot for  
your system is in the ‘wrong’ place on the Cr104 keypad  
for your comfort. It’s quite easy to reassign a favourite  
function to a more accessible key. It is even possible  
to move a function from one Device Mode to another  
Device Mode.  
1. Press and hold  
until the power LED blinks  
S
twice:  
2. Press  
3. Press  
.
* *  
press  
on your Cr104; this feature is switched on by  
A
default.  
.
9 9 5  
For example, you might want to turn off your TV, VCr  
and Satellite at the same time.  
.
h
ere are times, however, when you might want to  
control a device’s volume directly when in a specific  
Device Mode.  
4. Press and hold  
until the power LED blinks  
S
A key programmed with a Macro is available in all  
modes; it will replace that keys different functions  
for all modes.  
<
example: To assign the  
function to the  
D
U
twice:  
.
* *  
key in SaT mode  
1. Press  
.
z
example: To cancel volume punch-through  
A Macro can consist of up to eight key presses.  
2. Press and hold  
until the power LED blinks  
<
S
for a TV (aV mode)  
twice:  
3. Press  
.
* *  
9 9 4  
1. Press  
once.  
a
example: To assign a Macro to the  
key  
h
.
2. Press and hold  
until the power LED blinks  
1. Press and hold  
until the power LED blinks  
S
S
4. Press the key you want to move (e.g.  
)
D
twice:  
3. Press  
4. Press  
.
twice:  
2. Press  
3. Press  
.
* *  
* *  
5. Press the key you want to move the key to (e.g.  
.
.
9 9 3  
9 9 5  
).  
U
. e power LED blinks four times.  
(the Macro will be assigned to this key).  
-
h
now, pressing either  
Mode makes the Cr104 transmit the  
or  
while in SAT Device  
D
U
4. Press a,  
,
,
,
,
. (ese are the  
now, while in TV (AV) mode, you will be able to control  
the volume or mute functions of your TV directly.  
P w P z P  
Macro steps you wish to record.)  
function.  
D
To completely swap over the functionality of the two  
5. To store the Macro, press and hold  
until the  
S
To completely cancel all volume punch-  
keys to put the  
functionality on the  
key, repeat  
and  
U
D
power LED blinks twice:  
.
* *  
through settings  
1. Press and hold  
the above process again, but swap over the  
key presses in the example.  
D
U
now, whenever you press  
, the Cr104 will toggle the  
until the power LED blinks  
h
S
power to your TV, VCr and Satellite.  
twice:  
2. Press  
.
* *  
9 9 3  
note that the function that is copied over to the new key  
is always the original function of the old key.  
e important word here is ‘toggle. For example,  
if the TV and Satellite devices are currently on,  
<
<
<
.
3. Press  
. e power LED blinks four times  
.
+
*
but the VCr is off, pressing  
will switch off the  
Restore a moved key  
h
* * *  
TV and Satellite and switch on the VCr (rather  
than switching all three devices on or off).  
To restore a key to its previous function, repeat the  
example above, pressing the key to be restored twice  
(copy it back to itself).  
now, whichever mode you’re in, you will have direct  
access to that device’s volume or mute functions,  
assuming they are available. You would need to switch to  
aMP mode to alter the AVr500/AVr600/AV888 volume.  
When using Macros, remember that you may  
need to change mode or use  
, and that each  
S
Restore all moved keys for a device Mode  
To restore all keys in a Device Mode to their original  
functional positions, repeat the example above, but press  
the relevant Device Mode key (e.g.  
5 in the example.  
key press (including changing modes and pressing  
) counts as one of the Macro steps. You cannot  
S
example: To restore default volume punch-  
use a Macro key within another Macro.  
through settings to all device Modes  
) at points 1,4 and  
A
If the amount of memory storage for a particular  
Macro is exceeded, the power LED comes on for  
five seconds. You can, however, save the macro  
1. Press and hold  
until the power LED blinks  
S
twice:  
2. Press  
.
9 9 3  
* *  
.
steps up to that point by pressing  
, or you can  
S
cancel the Macro recording by pressing any other  
key.  
3. Press  
. e power key LED blinks twice:  
A
*
.
*
e delay between key presses is recorded as  
part of the Macro. A delay of up to 30 seconds is  
permitted.  
<
e-27  
To toggle a Device Mode lock setting:  
copy a key between device Modes  
Mode Mover  
locking/unlocking a specific  
1. Press the Device Mode key you want to unlock  
It is possible to copy functions between Device Modes.  
However, remember that button functions are Device  
Mode specific and therefore effectively ‘punch-through’  
to the original Device Mode when copied over.  
device Mode  
If your home entertainment setup contains devices of  
the same type (e.g. two TVs, perhaps from different  
manufacturers) you can still control both those devices  
with the Cr104. You simply need to reassign an unused  
Device Mode key.  
(e.g.  
)
c
When you first unpack your Cr104 and insert the  
batteries, for your convenience it is able to control  
certain Arcam components automatically (e.g. DVD  
players, Amplifiers, Tuners and CD Players). We achieve  
this by preprogramming specific Arcam device codes  
onto the relevant Device Mode keys, then locking  
the Device Modes so you don’t reprogram them  
inadvertently.  
2. Press and hold  
until the power LED blinks  
S
twice:  
3. Press  
.
* *  
9 8 2  
e following example copies the AVr500/AVr600/  
AV888 DIRECT function from the Cr104 aMP device  
.
e power LED blinks twice when being locked,  
and blinks four times when being unlocked.  
<
mode to the shiſted function of the  
Device Mode.  
button on aV  
#
NOTE  
If you enter an invalid key sequence, the power  
LED gives one long blink and returns to normal  
operation.  
<
Before using Mode Mover, make sure both the  
source and destination Device Mode keys are  
unlocked (see next section).  
1. Press and hold  
until the power LED blinks  
S
twice:  
.
* *  
9 9 4  
If you want to override these locked default settings – to  
control a third-party CD player, for example – you will  
first need to unlock CD Mode before setting up the  
Cr104 using one of the methods described at the start  
of this guide.  
2. Press  
.
While the Device Mode key is locked, the Direct Code  
Setup and Move Mode functions are not available.  
3. Press the Device Mode key of the function you  
want to move (e.g. ).  
A
example: To use the  
key to control a  
z
4. Press the function key you want to move (e.g.  
/
)
second TV  
DIRECT)  
1. Press and hold  
until the power LED blinks  
Here are the factory default settings:  
S
5. Press the key of the Device Mode you want to  
copy the function to (e.g.  
twice:  
3. Press  
.
* *  
9 9 2  
Device Mode  
Default status  
Default Arcam  
codes  
)
a
.
6. Press the  
button graphic  
S
3. Press the Device Mode key for the type of device  
you want to control (e.g. for a TV, press ).  
BD  
SaT  
aV  
Locked  
Unlocked  
Unlocked  
Locked  
0762  
1205  
0586  
2009  
1242  
1930  
0111  
2010  
7. Press the key you want to copy the function to  
(e.g.  
a
)
#
4. Press the Device Mode key you want to use (e.g.  
If you prefer to copy the key to the main function of the  
).  
z
button instead of the ‘shiſted’ function, omit point 6  
#
5. Don’t forget to set up the Cr104 to control the  
second device, using one of the methods from  
“Controlling other devices” on page E-15.  
TuN  
aMP  
PVR  
VCR  
CD  
in the above example.  
Locked  
Unlocked  
Unlocked  
Locked  
note that volume punch-through is not applied to a  
Device Mode that has been copied using Mode Mover.  
However, volume punch-through functionality can be  
restored when you have used Mode Mover, by copying  
,
and  
from the AMP Device Mode to the  
- +  
@
Alternative codes are available for multi-room solutions,  
or in the case of code clashes with other manufacturers  
products.  
same physical buttons on the new moved Device Mode  
using the last example shown in Key Mover.  
To restore a moved device Mode key to its  
For example:  
original state  
1. Press and hold  
aMP (system code 19)  
1954  
until the power LED blinks  
S
twice:  
2. Press  
.
* *  
9 9 2  
You will need to change the system code on the product  
you wish to control, as well as the Cr104.  
.
3. Press the Device Mode key you want to restore  
twice.  
NOTE  
e aMP Device Mode can only be used to control  
Arcam amplifiers like the AVr500, AVr600 and  
AV888, either on its default or alternative Ir system  
codes.  
e-28  
Mode key iR punch-through  
Device codes  
Command summary  
direct code setup  
e Mode key Ir punch-through default is ‘on.  
key mover  
(e.g. SAT mode, DISP key to MEnU key)  
e tables that begin on page 34 (in the final section of  
this Handbook) list the four-figure codes for different  
manufacturers’ devices.  
example: To set the Mode key iR punch-  
through to aMP  
1. Press and hold  
(e.g. AV mode, nnnn=code number)  
until the power LED blinks  
S
z S * * 9 9 4 D U  
nnnn  
a S * *  
* * P  
twice:  
.
* *  
Use these when setting your Cr104 up to control your  
devices, as described in Method 1 (see page E-15).  
Mode mover  
(e.g. change SAT to TV(AV))  
2. Press  
. e power LED blinks twice:  
library search  
(e.g. AV mode)  
9 7 1  
If more than one code number is listed, try the first  
number. If the results are unsatisfactory, continue trying  
the numbers for that manufacturer to get the best ‘fit’  
with the functionality required.  
.
* *  
3. Press  
A
S * * 9 9 2 a z  
to punch through Ir from it.  
until unit turns off  
a S 9 9 1 * * P [  
Restore device mode  
(e.g. restore SAT)  
now, whenever you press and release a Mode key, the  
Ir data assigned to aMP is transmitted, no matter what  
the current mode is (i.e. it ‘punches through’ any other  
device).  
to save  
S
code blink back  
If the manufacturer of your equipment is not listed, you  
can try Method 2, the Library Search (see page E-15). is  
allows you to scan through every set of codes contained  
in the Cr104s memory.  
S * * 9 9 2 z z  
a S 9 9 0 **  
locking/unlocking a mode  
(e.g. CD mode)  
count blinks for first N  
1
To cancel Mode key iR punch-through  
count blinks for second N  
1. Press and hold  
until the power LED blinks  
2
S
c S * * 9 8 2 * *  
twice:  
.
count blinks for third N  
* *  
3
(i.e. two blinks for lock)  
2. Press  
. e power LED blinks twice:  
count blinks for fourth N  
9 7 1  
4
c S * * 9 8 2 * * * *  
.
* *  
code learning  
(e.g. AV mode fast forward key)  
(i.e. four blinks for unlock)  
3. Press  
until the power LED blinks twice:  
S
*
.
cancel all volume punch-through  
S * * 9 9 3 + * * * *  
*
(many  
S * * 9 7 5 * * a ( *  
rapid blinks)  
Resetting the cR104  
(Press key on original remote that you wish to copy)  
Restore volume punch-through  
S * * 9 9 3 A * *  
resetting the Cr104 will erase all learned functions  
across all modes, as well as some other programmed  
functions like Macros. It will not reset the Device Mode  
keys; these will remain programmed to your choice of  
component.  
* * S * *  
delete a learned function  
(e.g. AV mode fast forward key)  
Mode key iR punch-through  
S * * 9 7 1 * * A  
S * * 9 7 5 * * a ( ( * *  
cancel mode key iR punch-through  
S * * 9 7 1 * * S * *  
1. Press and hold  
until the power LED blinks  
S
delete all learned functions with a device  
(e.g. AV mode)  
twice:  
2. Press  
times:  
.
* *  
. e power LED blinks four  
.
9 8 0  
S * * 9 7 5 a a  
* * * *  
3. Press and hold  
until the power LED blinks  
creating macros  
S
twice:  
4. Press  
.
* *  
9 9 3  
(e.g. SrCH key)  
.
S * * 9 9 5 h a P w P z P S  
* *  
5. Press  
. e power key LED blinks twice:  
A
*
.
NOTE  
*
deassign macro  
S * * 9 9 5 h S * *  
6. Press and hold  
until the power LED blinks  
As elsewhere in this Handbook, a single ‘blink’ of  
the red LED behind the power button is indicated  
by the symbol  
S
twice:  
.
* *  
.
*
7. Press  
. e power LED blinks twice:  
9 7 1  
.
* *  
8. Press  
. e power key LED blinks twice:  
A
*
.
*
e-29  
IR  
commands  
ese are the Ir commands generated from the BD player  
remote control, and accepted by the BDP100. e codes are  
useful if you wish to programme another remote handset  
to control the BDP100. e codes are given in the format  
SystemCode–CommandCode. 25 (0x19) is the Arcam  
System Code for a Blu-ray Disc player.  
Key name  
Decimal  
25–0  
25–1  
25–2  
25–3  
25–4  
25–5  
25–6  
25–7  
Hexadecimal  
0x19–0x00  
0x19–0x01  
0x19–0x02  
0x19–0x03  
0x19–0x04  
0x19–0x05  
0x19–0x06  
0x19–0x07  
0x19–0x08  
0x19–0x09  
0x19–0x12  
0x19–0x40  
0x19–0x1D  
0x19–0x4C  
0x19–0x20  
Key name  
NaVIgaTE uP  
NaVIgaTE LEFT  
OK  
Decimal  
25–86  
25–81  
25–87  
25–80  
25–85  
25–45  
25–48  
25–53  
25–54  
25–75  
16–13  
16–16  
16–17  
25–88  
25–73  
25–69  
25–65  
25–74  
25–107  
25–108  
25–109  
25–110  
Hexadecimal  
0x19–0x13  
0x19–0x51  
0x19–0x57  
0x19–0x50  
0x19–0x55  
0x19–0x2D  
0x19–0x30  
0x19–0x35  
0x19–0x36  
0x19–0x4B  
0x10–0x0D  
0x10–0x10  
0x10–0x11  
0x19–0x58  
0x19–0x49  
0x19–0x45  
0x19–0x41  
0x19–0x4A  
0x19–0x6B  
0x19–0x6C  
0x19–0x6D  
0x19–0x6E  
0
1
2
3
NaVIgaTE RIgHT  
4
NaVIgaTE DOWN  
LOaD  
5
6
PauSE  
7
PLaY  
8
STOP  
25–8  
25–9  
9
STaTuS  
MuTE  
DISP  
RND  
RPT  
SRCH  
25–18  
25–64  
25–29  
25–76  
25–32  
VOL+  
VOL–  
24P  
aNgLE  
auDIO  
SuBT  
/
0
25–33  
25–50  
25–52  
0x19–0x21  
0x19–0x32  
0x19–0x34  
7
SETuP  
8
RED / a  
gREEN / B  
YELLOW / C  
BLuE / D  
MENu (POPuP MENu)  
25–67  
25–58  
25–72  
25–66  
0x19–0x43  
0x19–0x3A  
0x19–0x48  
0x19–0x42  
CaNCEL  
RETuRN  
TITLE (TOP MENu)  
e-30  
Radio interference  
e BDP100 Blu-ray Disc player is a digital device  
which has been designed to very high standards of  
electromagnetic compatibility.  
All Blu-ray players generate, and can radiate rF  
(radio frequency) energy. In some cases this can cause  
interference with FM and AM radio reception. If this is  
the case, keep the player and its connecting cables as far  
from the tuner and its aerials as possible. Connecting  
the player and the tuner to different mains sockets can  
also help to reduce interference.  
Analogue Audio Output  
Digital to Analogue conversion  
Signal to noise ratio  
24-bit 192kHz Delta-Sigma DAC  
110dB CCIr  
0.002%  
Harmonic distortion (1kHz)  
Frequency response ( 0.5dB)  
Output level (0dB)  
specifications  
10Hz–20kHz  
2.2Vrms  
47Ω  
Output impedance  
Minimum recommended load  
Video Outputs  
5kΩ  
EC COUnTrIES – is products have been designed to  
comply with EMC Directive 2004/108/EC.  
Composite video  
1 x phono. 1V pk-pk in 75Ω  
Component video  
Interlaced or Progressive  
3 phono sockets.  
Y 1V pk-pk in 75Ω, Pb 0.7V pk-pk in 75Ω, Pr 0.7V pk-pk in 75Ω  
USA – ese products comply with FCC Part 15  
Class B.  
HDMI  
19-pin HDMI connector  
Supported video formats are:  
laser radiation  
If the BDP100 Blu-ray Disc  
player is operated whilst  
he outer casing is removed,  
nvisible laser radiation could  
cause eye damage.  
720 x 576p, 720(1440) x 576i, 720 x 480p, 720(1440) x 480i,  
1280 x 720p, 1920 x 1080i, 1920 x 1080p  
Audio to 6-channel/96kHz or 2-channel/192kHz (24-bit).  
Digital interfaces  
USB  
USB 2.0 High Speed (480 Mbit/s)  
10 BASE-T / 100 BASE-TX  
network  
Physical  
Dimensions  
Weight  
W430 x D400 x H100mm  
6.2kg nett/10.0kg packed  
30W maximum  
Power consumption  
Digital output connection  
75co-axial  
optical TOSLInK  
Supplied accessories  
Mains lead  
Cr104 remote control  
4 x AAA batteries  
E&OE  
NOTE: All specification values are typical unless otherwise stated  
continual improvement policy  
Arcam has a policy of continual improvement for its  
products. is means that designs and specifications  
are subject to change without notice.  
e-31  
In addition, mere aggregation of another work not based on  
the Program with the Program (or with a work based on the  
Program) on a volume of a storage or distribution medium does  
not bring the other work under the scope of this License.  
3. You may copy and distribute the Program (or a work based  
on it, under Section 2) in object code or executable form under  
the terms of Sections 1 and 2 above provided that you also do  
one of the following:  
a) Accompany it with the complete corresponding machine-  
readable source code, which must be distributed under the  
terms of Sections 1 and 2 above on a medium customarily used  
for soſtware interchange; or,  
b) Accompany it with a written offer, valid for at least three  
years, to give any third party, for a charge no more than your  
cost of physically performing source distribution, a complete  
machine-readable copy of the corresponding source code, to  
be distributed under the terms of Sections 1 and 2 above on a  
medium customarily used for soſtware interchange; or,  
c) Accompany it with the information you received as to the  
offer to distribute corresponding source code. (is alternative  
is allowed only for noncommercial distribution and only if you  
received the program in object code or executable form with  
such an offer, in accord with Subsection b above.)  
e source code for a work means the preferred form of the  
work for making modifications to it. For an executable work,  
complete source code means all the source code for all modules  
it contains, plus any associated interface definition files, plus  
the scripts used to control compilation and installation of  
the executable. However, as a special exception, the source  
code distributed need not include anything that is normally  
distributed (in either source or binary form) with the major  
components (compiler, kernel, and so on) of the operating  
system on which the executable runs, unless that component  
itself accompanies the executable.  
If distribution of executable or object code is made by offering  
access to copy from a designated place, then offering equivalent  
access to copy the source code from the same place counts as  
distribution of the source code, even though third parties are  
not compelled to copy the source along with the object code.  
4. You may not copy, modify, sublicense, or distribute the  
Program except as expressly provided under this License.  
Anyattempt otherwise to copy, modify, sublicense or distribute  
the Program is void, and will automatically terminate your  
rights under this License. However, parties who have received  
copies, or rights, from you under this License will not have  
their licenses terminated so long as such parties remain in full  
compliance.  
gnU gEnErAL PUBLIC LICEnSE  
Version 2, June 1991  
Copyright (C) 1989, 1991 Free Soſtware Foundation, Inc.  
51 Franklin Street, Fiſth Floor, Boston, MA 02110-1301, USA  
Everyone is permitted to copy and distribute verbatim copies of  
this license document, but changing it is not allowed.  
containing the Program or a portion of it, either verbatim or  
with modifications and/or translated into another language.  
(Hereinaſter, translation is included without limitation in the  
term “modification.) Each licensee is addressed as “you.  
Activities other than copying, distribution and modification are  
not covered by this License; they are outside its scope. e act  
of running the Program is not restricted, and the output from  
the Program is covered only if its contents constitute a work  
based on the Program (independent of having been made by  
running the Program). Whether that is true depends on what  
the Program does.  
software  
licencing  
Preamble  
e licenses for most soſtware are designed to take away your  
freedom to share and change it. By contrast, the gnU general  
Public License is intended to guarantee your freedom to share  
and change free soſtware--to make sure the soſtware is free for  
all its users. is general Public License applies to most of the  
Free Soſtware Foundation’s soſtware and to any other program  
whose authors commit to using it. (Some other Free Soſtware  
Foundation soſtware is covered by the gnU Lesser general  
Public License instead.) You can apply it to your programs, too.  
When we speak of free soſtware, we are referring to freedom,  
not price. Our general Public Licenses are designed to make  
sure that you have the freedom to distribute copies of free  
soſtware (and charge for this service if you wish), that you  
receive source code or can get it if you want it, that you can  
change the soſtware or use pieces of it in new free programs;  
and that you know you can do these things.  
To protect your rights, we need to make restrictions that forbid  
anyone to deny you these rights or to ask you to surrender the  
rights. ese restrictions translate to certain responsibilities for  
you if you distribute copies of the soſtware, or if you modify  
it. For example, if you distribute copies of such a program,  
whether gratis or for a fee, you must give the recipients all the  
rights that you have. You must make sure that they, too, receive  
or can get the source code. And you must show them these  
terms so they know their rights.  
We protect your rights with two steps: (1) copyright the  
soſtware, and (2) offer you this license which gives you legal  
permission to copy, distribute and/or modify the soſtware.  
Also, for each author’s protection and ours, we want to make  
certain that everyone understands that there is no warranty for  
this free soſtware. If the soſtware is modified by someone else  
and passed on, we want its recipients to know that what they  
have is not the original, so that any problems introduced by  
others will not reflect on the original authors’ reputations.  
Finally, any free program is threatened constantly by soſtware  
patents. We wish to avoid the danger that redistributors of a  
free program will individually obtain patent licenses, in effect  
making the program proprietary. To prevent this, we have made  
it clear that any patent must be licensed for everyone’s free use  
or not licensed at all.  
EngLISH  
1.You may copy and distribute verbatim copies of the Program’s  
source code as you receive it, in any medium, provided that  
you conspicuously and appropriately publish on each copy an  
appropriate copyright notice and disclaimer of warranty; keep  
intact all the notices that refer to this License and to the absence  
of any warranty; and give any other recipients of the Program a  
copy of this License along with the Program.  
You may charge a fee for the physical act of transferring a  
copy, and you may at your option offer warranty protection in  
exchange for a fee.  
2. You may modify your copy or copies of the Program or any  
portion of it, thus forming a work based on the Program, and  
copy and distribute such modifications or work under the terms  
of Section 1 above, provided that you also meet all of these  
conditions:  
a) You must cause the modified files to carry prominent notices  
stating that you changed the files and the date of any change.  
is item incorporates copy protection technology that is  
protected by U.S. patents and other intellectual property rights  
of rovi Corporation. reverse engineering and disassembly are  
prohibited.  
“AVCHD” and the AVCHD” logo are trademarks of Panasonic  
Corporation and Sony Corporation.  
Java and all Java-based trademarks and logos are trademarks or  
registered trademarks of Sun Microsystems, Inc. in the U.S. and  
other countries.  
e “BD-LIVE” logo is a trademark of Blu-ray Disc  
Association.  
b) You must cause any work that you distribute or publish, that  
in whole or in part contains or is derived from the Program or  
any part thereof, to be licensed as a whole at no charge to all  
third parties under the terms of this License.  
“Blu-ray Disc, Blu-ray” and the “Blu-ray Disc” logo are  
trademarks of Blu-ray Disc Association.  
“BOnUSVIEW” is a trademark of Blu-ray Disc Association.  
c) If the modified program normally reads commands  
interactively when run, you must cause it, when started running  
for such interactive use in the most ordinary way, to print or  
display an announcement including an appropriate copyright  
notice and a notice that there is no warranty (or else, saying  
that you provide a warranty) and that users may redistribute  
the program under these conditions, and telling the user how to  
view a copy of this License. (Exception: if the Program itself is  
interactive but does not normally print such an announcement,  
your work based on the Program is not required to print an  
announcement.)  
ese requirements apply to the modified work as a whole.  
If identifiable sections of that work are not derived from the  
Program, and can be reasonably considered independent and  
separate works in themselves, then this License, and its terms,  
do not apply to those sections when you distribute them as  
separate works. But when you distribute the same sections  
as part of a whole which is a work based on the Program, the  
distribution of the whole must be on the terms of this License,  
whose permissions for other licensees extend to the entire  
whole, and thus to each and every part regardless of who wrote  
it.  
Manufactured under license from Dolby Laboratories.  
Dolby and the double-D symbol are trademarks of Dolby  
Laboratories.  
Manufactured under license under U.S. Patent #’s: 5,451,942;  
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,392,195;  
7,272,567; 7,333,929; 7,212,872 & other U.S. and worldwide  
patents issued & pending. DTS and the Symbol are registered  
trademarks, & DTS-HD, DTS-HD Master Audio | Essential and  
the DTS logos are trademarks of DTS, Inc. Product includes  
soſtware. © DTS, Inc. All rights reserved.  
is a trademark of DVD format/Logo licensing  
Corporation.  
5. You are not required to accept this License, since you have  
not signed it. However, nothing else grants you permission to  
modify or distribute the Program or its derivative works. ese  
actions are prohibited by law if you do not accept this License.  
erefore, by modifying or distributing the Program (or any  
work based on the Program), you indicate your acceptance  
of this License to do so, and all its terms and conditions for  
copying, distributing or modifying the Program or works based  
on it.  
6. Each time you redistribute the Program (or any work based  
on the Program), the recipient automatically receives a license  
from the original licensor to copy, distribute or modify the  
Program subject to these terms and conditions. You may not  
HDMI, the HDMI logo and High-Definition Multimedia  
Interface are trademarks or registered trademarks of HDMI  
Licensing LLC.  
MPEg Layer-3 audio coding technology licensed from  
Fraunhofer IIS and omson.  
Windows Media and the Windows logo are trademarks or  
registered trademarks of Microsoſt Corporation in the United  
States and/or other countries.  
is product uses some soſtware programs which are listributed  
under the gPL license. Accordingly, the following gPL soſtware  
source codes that have been used in this product can be  
e precise terms and conditions for copying, distribution and  
modification follow.  
TErMS AnD COnDITIOnS FOr COPYIng,  
DISTrIBUTIOn AnD MODIFICATIOn  
is License applies to any program or other work which  
contains a notice placed by the copyright holder saying it may  
be distributed under the terms of this general Public License.  
e “Program, below, refers to any such program or work, and  
a “work based on the Program” means either the Program or  
any derivative work under copyright law: that is to say, a work  
us, it is not the intent of this section to claim rights or contest  
your rights to work written entirely by you; rather, the intent is  
to exercise the right to control the distribution of derivative or  
collective works based on the Program.  
e-32  
impose any further restrictions on the recipients’ exercise of  
the rights granted herein. You are not responsible for enforcing  
compliance by third parties to this License.  
11. BECAUSE THE PrOgrAM IS LICEnSED FrEE  
OF CHArgE, THErE IS nO WArrAnTY FOr THE  
PrOgrAM, TO THE EXTEnT PErMITTED BY  
APPLICABLE LAW. EXCEPT WHEn OTHErWISE  
STATED In WrITIng THE COPYrIgHT HOLDErS  
AnD/Or OTHEr PArTIES PrOVIDE THE PrOgrAM  
AS IS” WITHOUT WArrAnTY OF AnY KInD,  
EITHEr EXPrESSED Or IMPLIED, InCLUDIng, BUT  
nOT LIMITED TO, THE IMPLIED WArrAnTIES OF  
MErCHAnTABILITY AnD FITnESS FOr A PArTICULAr  
PUrPOSE. THE EnTIrE rISK AS TO THE QUALITY AnD  
PErFOrMAnCE OF THE PrOgrAM IS WITH YOU.  
SHOULD THE PrOgrAM PrOVE DEFECTIVE, YOU  
ASSUME THE COST OF ALL nECESSArY SErVICIng,  
rEPAIr Or COrrECTIOn.  
Soſtware Foundation, Inc., 59 Temple Place, Suite 330, Boston,  
MA 02111-1307 USA  
Also add information on how to contact you by electronic and  
paper mail.  
If the program is interactive, make it output a short notice like  
this when it starts in an interactive mode:  
gnomovision version 69, Copyright (C) year name of author  
gnomovision comes with ABSOLUTELY nO WArrAnTY; for  
details type ‘show w. is is free soſtware, and you are welcome  
to redistribute it under certain conditions; type ‘show c’ for  
details.  
e hypothetical commands ‘show w’ and ‘show c’ should show  
the appropriate parts of the general Public License. Of course,  
the commands you use may be called something other than  
‘show w’ and ‘show c’; they could even be mouse-clicks or menu  
items--whatever suits your program.  
You should also get your employer (if you work as a  
programmer) or your school, if any, to sign a “copyright  
disclaimer” for the program, if necessary. Here is a sample; alter  
the names:  
Yoyodyne, Inc., hereby disclaims all copyright interest in the  
program ‘gnomovision’ (which makes passes at compilers)  
written by James Hacker.  
signature of Ty Coon, 1 April 1989  
Ty Coon, President of Vice  
is general Public License does not permit incorporating  
you program into proprietary programs. If your program is  
subroutine library, you may consider it more useful to permit  
linking proprietary applications with the library. If this is what  
you want to do,  
use the gnU Library general Public License instead of this  
License.  
7. If, as a consequence of a court judgment or allegation of  
patent infringement or for any other reason (not limited to  
patent issues), conditions are imposed on you (whether by  
court order, agreement or otherwise) that contradict the  
conditions of this License, they do not excuse you from the  
conditions of this License. If you cannot distribute so as to  
satisfy simultaneously your obligations under this License and  
any other pertinent obligations, then as a consequence you  
may not distribute the Program at all. For example, if a patent  
license would not permit royalty-free redistribution of the  
Program by all those who receive copies directly or indirectly  
through you, then the only way you could satisfy both it and  
this License would be to refrain entirely from distribution of  
the Program. If any portion of this section is held invalid or  
unenforceable under any particular circumstance, the balance  
of the section is intended to apply and the section as a whole is  
intended to apply in other circumstances. It is not the purpose  
of this section to induce you to infringe any patents or other  
property right claims or to contest validity of any such claims;  
this section has the sole purpose of protecting the integrity of  
the free soſtware distribution system, which is implemented  
by public license practices. Many people have made generous  
contributions to the wide range of soſtware distributed through  
that system in reliance on consistent application of that system;  
it is up to the author/donor to decide if he or she is willing to  
distribute soſtware through any other system and a licensee  
cannot impose that choice. is section is intended to make  
thoroughly clear what is believed to be a consequence of the  
rest of this License.  
8. If the distribution and/or use of the Program is restricted in  
certain countries either by patents or by copyrighted interfaces,  
the original copyright holder who places the Program under  
this License may add an explicit geographical distribution  
limitation excluding those countries, so that distribution is  
permitted only in or among countries not thus excluded. In  
such case, this License incorporates the limitation as if written  
in the body of this License.  
9. e Free Soſtware Foundation may publish revised and/  
or new versions of the general Public License from time to  
time. Such new versions will be similar in spirit to the present  
version, but may differ in detail to address new problems  
or concerns. Each version is given a distinguishing version  
number. If the Program specifies a version number of this  
License which applies to it and “any later version, you have  
the option of following the terms and conditions either of that  
version or of any later version published by the Free Soſtware  
Foundation. If the Program does not specify a version number  
of this License, you may choose any version ever published by  
the Free Soſtware Foundation.  
12. In nO EVEnT UnLESS rEQUIrED BY APPLICABLE  
LAW Or AgrEED TO In WrITIng WILL AnY  
COPYrIgHT HOLDEr, Or AnY OTHEr PArTY WHO  
MAY MODIFY AnD/Or rEDISTrIBUTE THE PrOgrAM  
AS PErMITTED ABOVE, BE LIABLE TO YOU FOr  
DAMAgES, InCLUDIng AnY gEnErAL, SPECIAL,  
InCIDEnTAL Or COnSEQUEnTIAL DAMAgES ArISIng  
OUT OF THE USE Or InABILITY TO USE THE PrOgrAM  
(InCLUDIng BUT nOT LIMITED TO LOSS OF DATA  
Or DATA BEIng rEnDErED InACCUrATE Or LOSSES  
SUSTAInED BY YOU Or THIrD PArTIES Or A FAILUrE  
OF THE PrOgrAM TO OPErATE WITH AnY OTHEr  
PrOgrAMS), EVEn IF SUCH HOLDEr Or OTHEr PArTY  
HAS BEEn ADVISED OF THE POSSIBILITY OF SUCH  
DAMAgES.  
EnD OF TErMS AnD COnDITIOnS  
How to Apply ese Terms to Your new Programs  
If you develop a new program, and you want it to be of the  
greatest possible use to the public, the best way to achieve this  
is to make it free soſtware which everyone can redistribute and  
change under these terms.  
To do so, attach the following notices to the program. It is safest  
to attach them to the start of each source file to most effectively  
convey the exclusion of warranty; and each file should have at  
least the “copyright” line and a pointer to where the full notice  
is found.  
One line to give the program’s name and a brief idea of what  
it does.  
Copyright (C) <year><name of author>  
is program is free soſtware; you can redistribute it and/or  
modify it under the terms of the gnU general Public License  
as published by the Free Soſtware Foundation; either version 2  
of the License, or (at your option) any later version.  
is program is distributed in the hope that it will be useful,  
but WITHOUT AnY WArrAnTY; without even the implied  
warranty of MErCHAnTABILITY or FITnESS FOr A  
PArTICULAr PUrPOSE. See the gnU general Public  
License for more details.  
10. If you wish to incorporate parts of the Program into other  
free programs whose distribution conditions are different,  
write to the author to ask for permission. For soſtware which  
is copyrighted by the Free Soſtware Foundation, write to the  
Free Soſtware Foundation; we sometimes make exceptions for  
this. Our decision will be guided by the two goals of preserving  
the free status of all derivatives of our free soſtware and of  
promoting the sharing and reuse of soſtware generally.  
You should have received a copy of the gnU general Public  
License along with this program; if not, write to the Free  
nO WArrAnTY  
e-33  
e-34  
Worldwide guarantee  
is entitles you to have the unit repaired free of charge, during the first two years aſter  
purchase, provided that it was originally purchased from an authorised Arcam dealer.  
e Arcam dealer is responsible for all aſter-sales service. e manufacturer can take no  
responsibility for defects arising from accident, misuse, abuse, wear and tear, neglect or  
through unauthorised adjustment and/or repair, neither can they accept responsibility  
for damage or loss occurring during transit to or from the person claiming under the  
guarantee.  
product  
guarantee  
The warranty covers:  
Parts and labour costs for two years from the purchase date. Aſter two years you must pay  
for both parts and labour costs. e warranty does not cover transportation costs at any  
time.  
claims under guarantee  
is equipment should be packed in the original packing and returned to the dealer from  
whom it was purchased. It should be sent carriage prepaid by a reputable carrier – not  
by post. no responsibility can be accepted for the unit whilst in transit to the dealer or  
distributor and customers are therefore advised to insure the unit against loss or damage  
whilst in transit.  
For further details contact Arcam at:  
Arcam Customer Support Department,  
Pembroke Avenue, Waterbeach, CAMBrIDgE, CB25 9Qr, England  
or via www.arcam.co.uk.  
Problems?  
If your Arcam dealer is unable to answer any query regarding this or any other Arcam  
product please contact Arcam Customer Support at the above address and we will do our  
best to help you.  
on-line registration  
You can register your product on-line at www.arcam.co.uk.  
Correct disposal of this product  
is marking indicates that this  
product should not be disposed with  
other household waste throughout  
the EU.  
To prevent possible harm to the  
environment or human health from  
uncontrolled waste disposal and to  
conserve material resources, this  
product should be recycled responsibly.  
To dispose of your product, please use your local  
return and collection systems or contact the retailer  
where the product was purchased.  
e-35  

Alpine CDE 7856 User Manual
BenQ G900WA User Manual
Black Decker BX180 User Manual
Canon IXUS 105 User Manual
Graco PACK N PLAY 9747 User Manual
HP (Hewlett Packard) Hewlett Packard Car Video System 2010 User Manual
HP (Hewlett Packard) HP 33s User Manual
Huey Chiao HCB31 User Manual
JVC Car Stereo System KD R330 User Manual
JVC GR SX21EA User Manual