5 Make sure the paper is below the maximum fill
The MFP automatically engages the print
media.
Lexmark™ X342
Quick Reference
lines on the left inside wall of the tray.
6 Squeeze and adjust the paper guides until they
lightly touch the side of the stack of paper.
Loading paper and
specialty media
Loading paper in the paper tray
1 Remove the paper tray.
7 Close the paper tray.
Copying
Loading paper in the manual
feeder
Making a copy
1 Make sure:
1 Load the original document face-up into the
• You use paper designed for laser printers.
• The paper is not used or damaged.
• If you are using specialty paper, you follow the
instructions that came with it.
• You do not force paper into the MFP.
• Set the correct paper type and size in the
control panel, or using the computer.
ADF or face-down on the scanner glass.
2 Holding the tray on a stable surface, press the
guide lock, and slide the rear guide until it locks
at the paper length you want.
2 From the control panel, press Copy.
3 Enter the number of copies you want to print.
4 Press Start.
3 Prepare a stack of paper for loading by flexing
or fanning it back and forth. Straighten the
edges on a level surface.
Copying multiple pages onto a
single sheet (Paper Saver)
The Paper Saver feature lets you copy consecutive
pages of a multiple-page document on a single sheet
of paper.
2 Place a single sheet of paper face-up with the
leading edge first into the center of the manual
feeder, and adjust the paper guides to the paper
width.
4 Load the paper with the print side facing down.
1 Load paper.
2 Load the original document face-up into the
ADF or face-down on the scanner glass.
3 From the control panel, make sure Copy mode
is selected.
4 Under Copy, press Options.
5 Press
or
repeatedly until Paper Saver
is selected, and then press
.
Note: The toner cartridge snaps into place
Replacing the photoconductor
Cleaning the inside of the MFP
when correctly installed.
1 Press the access button on the left side of the
CAUTION: The fuser area is hot. Avoid contact
MFP, and open the front cover.
with the fuser area to prevent burns.
1
Warning: While cleaning the inside of the
MFP, be careful not to touch the
transfer roller located under the
toner cartridge. Oil from your fingers
can affect print quality.
7 Reinstall the print cartridge assembly.
1 Turn the MFP off, unplug the power cord, and
2
8 Press and hold Stop for three seconds to reset
then wait for the MFP to cool down.
photoconductor recount.
2 Open the front cover, and pull on the handle to
2 Pull on the handle to remove the print cartridge
9 Close the front cover.
remove the print cartridge assembly.
assembly.
Cleaning the scanner glass
1 Slightly dampen a soft, lint–free cloth or paper
towel with water.
2 Open the top cover.
3 Place the print cartridge assembly on a flat,
Warning: Do not touch the green
clean surface.
photoconductor drum.
4 To remove the toner cartridge:
3 Place the print cartridge assembly on a clean,
3 Wipe the surfaces of the scanner glass and
a Press the button on the print cartridge
dry surface.
ADF until they are clean and dry.
assembly.
4 With a dry, lint–free cloth, wipe away any dust
4 Wipe the underside of the white top cover and
b Remove the toner cartridge using the
and spilled toner from the print cartridge area.
white sheet until it is clean and dry.
handle.
5 Close the top cover.
Cleaning the outside of the MFP
Wipe the outside surface of the MFP with a soft,
clean, lint–free cloth. If you dampen the cloth slightly
with water, be careful not to let any water drip onto or
inside the MFP.
5 Unpack the photoconductor kit.
5 Reinsert the print cartridge assembly, and close
6 Install the toner cartridge into the new
the front cover.
photoconductor.
6 Plug in the power cord and turn the MFP on.
|