7+(ꢀ'2&80(17ꢀ&203$1<
ꢀꢁꢂꢃꢀ
DC230LP Windows NT® 4.0 TCP/IP Quick Install
IP Address
(current entry)
Installation Requirements:
>
2.
Access the System Administration menus:
d) Press [ ].
displays.
To install the DC230LP in a DHCP environment,
exclude the addresses assigned to the
DC230LP at the DHCP server.
a) Press [Online] to take the printer off
4.
IP Address Setup (skip this step if using
RARP):
Printer Off Line
line.
displays.
IP Address
(current entry)
=
*
Main Menu
Before Installation:
>
a) Press [ ].
displays.
b) Press [Menu].
displays.
Record the following information for use during
setup at the DC230LP:
Note: Use zeros to supplement each address
segment if fewer than 3 digits are used; e.g.,
13.252.25.08 = 013.252.025.008.
c) Press [ ], then press [ ] or [ ] until
System
Administration
>
TCP/IP Address:________________________
Gateway Address: ______________________
Subnet Mask: __________________________
Broadcast Address: _____________________
Host Name:____________________________
displays.
b) Use the [ ] or [ ] key to enter the
Enter Password
>
d) Press [ ].
displays.
first digit of the IP Address.
c) Press [ ] to move to the next digit.
Repeat this procedure to enter the
entire IP Address.
e) Use the [ ] and [ ] keys to enter
[2222].
Note: 2222 is the factory default password and
may be changed to suit your needs. Refer to the
DC230LP System Administration Guide,
Network Installation and Troubleshooting.
d) Press [Enter]. **SAVED**displays
momentarily, followed by
This installation procedure assumes that you
know how to navigate through the menu system
on the DC230LP Control Panel. Refer to the
quick reference card, Using the Menu System,
(701P96834) for assistance.
IP Address
(your entry)
>
.
System Admin
>
f) Press [Enter].
displays.
5.
RARP Setup:
Note: If you used a static IP Address, leave the
3.
Access the TCP/IP menus:
RARP setting at Disabled.
1.
Connect the DC230LP to your network
outlet or cable.
Port Setup
>
a) Press [ ].
displays.
a) To change the RARP setting, press
[ ] until the current setting displays
Network Setup
>
b) Press [ ] until
RARP
>
.
(current entry)
displays.
TCP/IP
>
c) Press [ ].
displays.
Over
For assistance, contact your local Xerox Customer Support Center:
USA: 1-800-821-2797 Canada: 1-800-939-3769
Page 1 of 4
7+(ꢀ'2&80(17ꢀ&203$1<
ꢀꢁꢂꢃꢀ
DC230LP Windows NT® 4.0 TCP/IP Quick Install
f) Press [Enter]. **SAVED**displays
d) Press [ ] repeatedly to delete the
momentarily, followed by
13.
At the client, install print drivers and map
the printer in the usual manner. Refer to
the CentreWare® manual, Getting Started
with Print and Fax Services, for additional
information.
current entry.
Enablement
>
.
Enabled
e) Use the [ ] or [ ] key to select the
Note: The next menu at this level, Port Setting,
has a fixed setting for the LPD (515) and can not
be changed.
first character in the Printer Name.
f) Press [ ] to move to the next charac-
ter. Repeat this procedure to enter the
entire Printer Name.
14.
TCP/IP protocol and TCP/IP print services
must be installed on the NT Server and the
printer name must be set to [lp] (lower
case) when configuring the LPR port.
Refer to the screen sample below.
11.
Save all settings:
Reset Required
g) Press [Enter]. **SAVED**displays
a) Press [Online].
Press ENTER key
momentarily, followed by
displays.
Printer Name
(your entry)
>
Additional information on the Windows NT
TCP/IP setup can be found in the DC230LP
System Administration Guide, Network Installa-
tion and Troubleshooting.
.
Warming Up
Please Wait . . .
>
b) Press [Enter].
10.
Enable the Line Printer Daemon (LPD):
displays. The DC230LP will reboot,
save the settings entered, and print a
Configuration Report in approximately
3 minutes.
a) Press [Escape] to move back a level
in the menu system.
TCP/IP-
>
displays.
12.
Check the settings on the Configuration
Report against those entered to be sure
they are correct.
Line Printer
Daemon
>
b) Press [ ] until
displays.
Enablement
(current entry)
>
c) Press [ ].
displays.
Enablement
(current entry)
=
*
d) Press [ ].
displays.
Enablement
Enabled
=
e) Press [ ] until
displays.
Page 3 of 4
7+(ꢀ'2&80(17ꢀ&203$1<
ꢀꢁꢂꢃꢀ
DC230LP Windows NT® 4.0 TCP/IP Quick Install
©1998 Xerox Corporation
701P98454 Version 1.0, 5-98
Page 4 of 4
|