Oricom Secure 50 User Manual

aby Monitor  
Secure 50  
User Guide  
WARNINGS AND SAFETY INFORMATION 1  
Do not place the cord in a high "wear and tear" location.  
Never use a frayed or compromised cord.  
IMPORTANT  
Please read this user guide thoroughly before use.  
Never use or place your Parent or Baby units in or near  
moisture or water (e.g. near bath or pool). Immersing in  
water can cause electric shock and even death.  
Your ORICOM Baby Monitor is designed to be an aid and  
should not be used as a substitute for responsible and  
proper adult supervision of a child.  
The Baby Monitor has been designed to provide some  
added reassurance in the form of sound transmission  
for those times when you are not in the same room as  
your baby provided you always stay within hearing range  
of the baby monitor during use. Your Baby Monitor is  
not a medical device, nor a device to prevent cases of  
Sudden Infant Death Syndrome (SID'S) or "cot death",  
and you should not rely on it for your baby's wellbeing. It is  
important that you regularly check on your baby personally.  
Power requirements  
In Australia this product requires an electrical supply of  
220-240 volts, single phase/alternating current.  
CAUTION  
Use only the mains power adaptors supplied with this  
equipment. Incorrect adaptor polarity or voltage can  
seriously damage the unit and/or cause physical harm  
and even death. The adaptors may become warm during  
use, please take care when handling.  
!
Make sure the Baby unit, Parent unit and mains adaptor  
cables are kept out of reach of your baby and other young  
children within the house at all times, at least one metre  
away from the baby's cot.  
AC Adaptor (Baby unit)  
Input: 240VAC 50Hz  
Output: 6VDC 200mA  
AC Adaptor (Parent unit)  
Input: 240VAC 50Hz  
Output: 6VDC 200mA  
Never place the baby unit inside your baby's cot, bed or  
playpen.  
If you plan to use your Baby monitor whilst travelling  
overseas, make sure that the voltage shown on the mains  
power adaptor is the same as the local mains power before  
connecting to the power supply. Do not use any voltage  
converter with the monitor.  
Never cover the Parent or baby units with clothes, towels  
or blankets or any other item.  
2 WARNINGS AND SAFETY INFORMATION  
• The Ni-MH batteries supplied with this product may be  
Battery requirements  
able to be recycled once they are unable to recharge  
during normal operation. Always observe your local  
Council /State regulations regarding the disposal of  
your packaging materials, exhausted batteries, and old  
equipment.  
Each parent unit requires two rechargeable Ni-MH  
batteries, size AAA 1.2V 800mAh (HR10/44).  
• Do not dispose of the batteries in a re, as they can  
explode.  
• Always recycle where possible. Do not use your baby  
monitor in an explosive hazard area such as where  
there is gas leaking.  
• Do not open, unscrew or temper with any of your  
baby monitor units or battery. Always carry out repairs  
through your authorised ORICOM representative or  
other duly qualied tradesperson.  
• As there is a slight chance that the product could be  
damaged by an electrical storm, it is recommended that  
users unplug from the mains supply during an electrical  
storm.  
• Released electrolyte from the battery is corrosive  
and can cause damage to the eyes or skin. It can  
be toxic and fatal if swallowed. If there is any sign of  
poisoning, immediately call emergency 000.  
Cleaning and care  
• When your Baby Monitor is not in use, it is recom-  
mended that you disconnect it from the mains supply  
and remove the batteries.  
The surface of the case can be cleaned with a dry, soft,  
lint-free cloth. Never use cleaning agents, particularly  
aggressive solvents. Apart from occasional cleaning of the  
case, no other care is necessary.  
• Observe the proper polarity, or direction, of any  
battery. Reverse insertion of the battery cell can  
result in leakage or explosion and in turn harm or  
even death.  
GETTING STARTED 3  
Thank you for choosing this monitor from Oricom.  
Installation  
Your Secure 50 Baby Monitor offers the best Digital  
Technology.  
For the Parent Unit  
clip  
1 Remove the Belt Clip by lifting  
the clip at the top and sliding it  
downwards.  
INTERFERENCE  
FREE FREQUENCY  
2 Then remove the battery cover  
on the back of the Parent Unit  
by switching the OPEN switch.  
Insert the rechargeable batteries  
(supplied) as marked on the unit  
and close the cover again.  
DECT (Digital Enhanced Cordless Telecommunications) is the  
most widely used worldwide digital cordless technology, offering  
amazingly clear sound, long range and maximum voice security.  
DECT operates on the 1.8Ghz frequency which eliminates potential  
interference from other common wireless devices such as cordless  
telephones, wireless networks (Wi-Fi), Bluetooth and cordless  
computer devices.  
3 Place the Parent Unit into the  
Charger Pod.  
battery cover  
4 Plug the mains adaptor into a  
mains power socket.  
Pack Contents  
The red charger light on the charger pod will illuminate  
indicating that the Parent Unit is charging.  
• Parent unit (receiver)  
• Baby unit (sender)  
(the light will remain on to ensure optimum charge is  
maintained).  
• Mains adaptor with charger pod  
• 2 x NiMH rechargeable batteries (type AAA, 800mAh)  
• Mains adaptor with power cord  
WARNING  
DO NOT USE STANDARD/ALKALINE BATTERIES  
IN THE PARENT UNIT, AS THERE IS A RISK OF  
EXPLOSION AND/OR INJURY. USE ONLY Ni-MH  
RECHARGEABLE BATTERIES AS SUPPLIED.  
!
4 GETTING STARTED  
5 Press [  
] to turn the Parent Unit on.  
4 Press [ ] to turn on the Baby Unit.  
• Before rst use, or if it has been out of use for a long  
time, the Parent Unit will need to be charged for 15-16  
hours. During this time, the Parent Unit will operate  
from the Charger pod when switched on. Note that the  
Parent Unit cannot be used without batteries, even if it  
is placed in the charger.  
• The Baby Unit should be placed about 1 metre  
to 1.5 metres away from the baby's cot on a flat  
surface. Never place the Baby Unit inside the cot,  
bed or playpen. Make sure the unit, cords and mains  
adaptor are out of reach of the baby and other  
young children. Never place either Unit on antique  
or polished surfaces (as slippage or scuffing may  
occur). The unit may cause harm if it falls onto baby  
or other young children.  
For the Baby Unit  
1 In the event of a power failure, your Baby Monitor can  
switch to battery power. It is therefore recommended that  
you insert non-rechargeable batteries in the Baby Unit.  
Note:  
If you place the Parent and Baby units too close together  
you will hear a high pitched noise called "feedback", this is  
normal. The units are designed to be located in separate  
rooms.  
To prevent feedback, do not take the parent unit into the  
nursery/baby's room.  
2 Remove the battery cover on the  
back of the Baby Unit by switching  
the OPEN switch. Insert 3 alkaline  
batteries of the type AA (not  
provided) as marked on the unit  
and close the cover again. Do not  
use rechargeable batteries in the  
Baby Unit.  
3 Plug the power cord into the power input at the side of  
the Baby Unit and plug the adaptor plug into a mains  
power socket.  
YOUR BABY MONITOR 5  
Baby unit (Sender)  
1 Night light Key  
1
2
3
Press to turn On the night light. Press again to turn off  
the Light.  
2 Power On/Off Key  
Press to turn the Unit ON.  
Press and hold to turn the Unit OFF.  
3 Page Key  
Press and hold this key, Parent unit makes an audible  
alert.  
Useful to call for assistance or to locate a missing  
Parent Unit.  
4 Power light  
4
5
Red light glows when the power is On. A slow ashing  
light indicates batteries are low.  
5 Microphone  
Picks up the sounds from your baby's room.  
6 YOUR BABY MONITOR  
Left view of baby unit  
Parent unit (Receiver)  
6 DC 6V input  
7 Battery Cover  
Connecting to Power Adaptor.  
Rechargeable batteries.  
8 Belt Clip  
9 Volume Up/Down Keys  
Adjust the Volume at which you hear the sounds in your  
baby's room.  
10 Power Key  
Press and release to turn it ON.  
Press and hold to turn it OFF.  
6
8
7
9
10  
YOUR BABY MONITOR 7  
11 Power Light  
Charger Pod  
Red light when the power is ON.  
Flashing light indicates rechargeable batteries need  
recharging.  
14 Charging Light  
When Parent unit is placed in the Charger Pod, the  
red charger light comes ON to indicate the batteries  
are charging. Light will remain ON to ensure optimum  
charge is maintained.  
12 Battery/Noise Level Indicators  
Indicates the battery level or Noise level  
13 Link Light  
Green light ON indicates “Linked” to Baby Unit. Flashing  
light indicates “Link” is lost.  
12  
11  
13  
14  
8 BASIC OPERATION  
Once you have set up your Baby Monitor, you will be able  
to hear the sounds in your baby's room through the Parent  
Unit. And also see the green and red sensor lights around  
the top of the Parent Unit rise and fall with the sound levels.  
and 3 red). The more audio is picked up, the more  
lights will be lit. When no audio is picked up, all 8  
lights will be off.  
• If the volume of the Parent Unit is turned off, an alert  
will sound when the audio reaches the second red  
led.  
Note:  
If the connection between the Parent and Baby Units is  
broken at any time the green Link light on the Parent Unit  
will ash slowly, the parent unit will beep to alter you that  
the link has been lost and the green and red sensor lights  
will cease to react to any sounds. Move closer to the baby  
unit or follow the directions in "Troubleshooting" chapter to  
re-establish the link.  
Note:  
Do not position the baby unit and the parent unit close to  
each other as feedback may be generated.  
Adjusting Volume  
You can adjust the volume at which you hear your baby.  
Power On/Off  
There are 5 volume levels and an Off setting on the  
Parent Unit.  
Once connected to the power supply,  
• Press [ ] on each Unit to turn on the power.  
• To switch off, press and hold the [ ].  
Press [  
] to increase the volume and [  
] to decrease  
the volume. When adjusting the volume, the 5 green sound  
sensor lights will illuminate to indicate the volume level.  
Monitoring  
Paging  
• Position the baby unit accordingly. It should be  
placed 1 metre to 1.5 metres away from the baby's  
cot on a at surface.  
If the Parent Unit is misplaced, you can use [ ] button on  
the Baby Unit to locate the Parent Unit.  
• Press and hold [ ] on the Baby Unit. The Parent Unit will  
automatically reset to mid volume and the paging alert will  
sound.  
• Take the parent unit to monitor.  
• Audio picked up by the baby unit microphone is  
depicted on the 8 lights on the parent unit (5 green  
BASIC OPERATION 9  
• To stop the Page alert, press any button on the  
Parent Unit, or press [ ] again on the Baby Unit.  
Low Battery  
Note:  
Baby Unit  
If no button is pressed, the paging tone will stop after 30  
seconds.  
When the battery power is low, the power light will ash.  
If the Parent Unit volume is off, the Parent Unit volume will  
reset to mid volume.  
Parent Unit  
When the batteries are low, the red power light will ash.  
And also the battery low warning beep will be heard. The  
unit still can be used for 30 minutes. You should put the  
parent unit on the charger pod to recharge the batteries.  
Night light  
The Baby Unit has a one touch night light which emits a  
soft starry glow, providing comfort and reassurance for your  
baby and allowing you to see them in a darkened room.  
Note:  
Low battery alert can be suppressed by pressing any  
button.  
Press [ ] on the top of the baby unit. A soft light will turn  
on gently. Press again and the light will fade away.  
Charging the Battery  
Out of Range  
The Parent Unit will work for up to 10 hours with fully  
charged batteries. If a battery low warning beep is heard  
and the red Power light on the Parent Unit is ashing, you  
should put the parent unit on the Charger Pod to recharge  
the batteries. You can still use your Parent Unit from the  
Charger Pod. When charging, the red power light on the  
charger will light steadily.  
When the baby and parent units have no link with each  
other (eg. Out of range, parent unit or Baby unit is not  
powered on), the green Link light flashes. The link break  
alert will be heard from the Parent Unit once only. When  
the units are linked, the green Link light will be steadily lit.  
When you switch on your Parent Unit, the green and red  
sensor lights will briey indicate the current charge level of  
the batteries in the following way:  
10 BASIC OPERATION  
Rechargeable batteries in the Parent unit give up to 10  
hours continuous usage. Please note however, that new  
batteries do not reach full capacity until they have been in  
normal use for several days.  
8 lights illuminated  
fully charged  
half charged  
Running rechargeable batteries right down at least once a  
week will help them last as long as possible. The charge  
capacity of rechargeable batteries will reduce with time as  
they age, so reducing the performance time of the parent  
unit. Eventually they will need to be replaced.  
6 lights illuminated  
4 lights illuminated  
battery is running  
low  
2 lights illuminated  
batteries need  
recharging  
(alarm beep sounds)  
Note:  
The parent unit can be used on or off the charger pod.  
When on the charger pod, the batteries will be recharged  
at the same time. However, the time it takes to charge the  
batteries to full will be longer when the unit is charged and  
used at the same time.  
The Parent Unit can't be operated on the charging cradle  
without batteries.  
TROUBLESHOOTING 11  
Problem  
Possible cause(s)  
The red power lights do not turn on when you plug 1. Check if the units are properly connected to the power supply.  
in the power.  
2. Check if the power is turned on. If not, Press [  
] to turn on the power.  
1. You may have moved out of range. Move closer to the Baby Unit and wait 5  
seconds for the Link to establish.  
2. You may need to reestablish the Link between the two units. Turn both units  
off by pressing and holding the [ ] and then turn on again by pressing the [ ].  
The green Link light on the Parent Unit is ashing  
and cannot hear the sounds from your baby's  
room.  
Can't hear your baby on the Parent Unit but the  
Link light is still glowing steadily.  
Check if the volume is turned up on the Parent Unit.  
Your re-chargeable batteries are running low. Return the Parent Unit to the  
Charger Pod to recharge them.  
The Red Power light is ashing on the Parent Unit  
1. The batteries in the parent unit are not fully charged. Charge the parent unit for  
14 hours before use.  
2. The power to the baby unit may be turned off or disconnected, and or the Baby  
unit may be turned off. Reconnect the AC power adaptor to the baby unit and  
or turn on the baby unit.  
3. You may have to re-establish the link between the two units. You will need to  
remove the batteries from the parent unit and register the parent unit back to  
the baby unit by following the instructions below:  
A. Ensure batteries are removed from the Parent unit (and baby unit if tted) and the  
AC power plug is disconnected from the Baby unit). Press and hold the [ ] on  
the BABY unit then plug in the AC power plug, after 2 seconds, when the baby  
unit night-lights ash release the [ ] button;  
B. Press and hold the [  
2 seconds, the parent unit will sound an alert and the level indication red  
LED’s will ash, then release the [ ] button;  
Two bars ash on the parent unit.  
] on the PARENT unit then insert the batteries, after  
C. After a few seconds, the PARENT unit will give a conrmation tone and the  
units will be re-linked and ready to use.  
NOTE: Steps A and B need to be performed within 50 secs.  
A high pitched ear piercing noise will be heard  
from the units (feedback).  
Check if the Parent and Baby Units are too close together. Move them further apart.  
12 PRODUCT SPECIFICATIONS  
Feature  
Specications  
Operating Frequency  
DECT 1.8 GHz  
Up to 300m under optimum conditions. The range is  
reduced in buildings (up to 50m) as a result of walls, doors  
etc.  
Range  
Input: 240 VAC 50Hz  
Power supply (baby unit)  
Output: 6 VDC, 200 mA,  
Non rechargeable batteries (baby unit)  
(not included in the package contents)  
Type: AA, 1.5 V Alkaline  
Transmitting power  
Average: 10 mW Maximum: 250 mW  
Input: 240 VAC, 50Hz  
Output: 6 VDC, 200 mA  
Power supply (parent unit)  
Rechargeable batteries (parent unit)  
(included in the package contents)  
Type: AAA, 1.2 V, 800 mAh NiMH  
Approx. 10 hours  
Operating time with charged battery  
GUARANTEE 13  
Warranty Information (Australia)  
Oricom makes no other warranties or conditions, express or implied, including  
as to merchantability and tness for a particular purpose, except as stated in  
this Warranty. Any implied warranties that may be imposed by law are limited  
in duration to the Warranty Period.  
During the Warranty Period, Oricom will replace and where possible repair  
the defective product. All component parts removed under this Warranty  
become the property of Oricom.  
In the unlikely event that your Oricom product has a recurring failure, Oricom,  
at its discretion, may elect to provide you with a replacement product of its  
choosing that is at least equivalent to your product in performance.  
Oricom warrants that the product is free from defects in materials or  
workmanship during the Warranty Period. This Warranty in no way affects  
your statutory warranty rights under the Trade Practices Act 1974 or any  
other similar legislation. This Warranty does not extend to any product from  
which the serial number has been removed, was purchased outside of  
Australia or that has been damaged or rendered defective:  
Oricom does not warrant that the operation of the product will be  
uninterrupted or error free. Oricom is not responsible for damage that occurs  
as a result of your failure to follow the instructions that came with the product.  
These terms and conditions together with any specic terms and conditions  
contained in the user guide to the product purchased constitute the complete  
and exclusive agreement between you and Oricom regarding the product. No  
change to the conditions of this Warranty is valid unless it is made in writing  
and signed by an authorised representative of Oricom.  
1. as a result of lightning, over voltage, accident, misuse, abuse or other  
external causes;  
2. the operation outside the normal use of the product;  
3. by the use of parts not manufactured or sold by Oricom; or  
4. by modication or service by anyone other than:  
(a) Oricom; or (b) an Oricom authorised service provider.  
Oricom is not liable for any damages caused by the product or the failure  
of the product to perform, including any lost profits or savings or special,  
incidental or consequential damages. Oricom is not liable for any claim made  
by a third party or made by you on behalf of a third party.  
The Warranty Period will be 36 months from the date of purchase of the  
product evidenced by your dated sales receipt. You are required to provide  
proof of purchase as a condition of receiving warranty services. You are  
entitled to a replacement or repair according to the terms and conditions of  
this document if your product is found to be faulty within the Warranty Period.  
This Warranty extends to the original purchaser only and is not transferable.  
This limitation of liability applies whether damages are sought, or a claim  
made, under this Warranty or as a tort claim (including negligence and strict  
product liability), a contract claim or any other claim. However, this limitation  
of liability will not apply to claims for personal injury.  
Nothing in this Warranty excludes, restricts or modifies any condition,  
warranty, right or remedy which pursuant to the Trade Practices Act 1974  
applies to this Warranty and which may not be so excluded, restricted or  
modified. For warranties that cannot be excluded, restricted or modified,  
Oricom limits the remedies available to those specified in the relevant  
legislation.  
Batteries (if supplied) with this product are covered under this warranty for a  
period of 90 days. Oricom products are manufactured using new materials  
or new and used materials equivalent to new in performance and reliability.  
Spare parts may be new or equivalent to new. Spare parts are warranted to  
be free from defects in material or workmanship for thirty (30) days or for the  
remainder of the Warranty Period of the Oricom branded product in which  
they are installed, whichever is longer.  
Customer Support  
If you suspect your product is not functioning to specication, before making a warranty claim please use the following  
resources.  
- Troubleshooting Guide in this user guide  
- Email our customer support team on [email protected]  
- Contact Oricom Customer Support team on 1300 889 785 or 02 4574 8888 (Monday to Friday 9am to 5pm EST)  
Please retain your purchase receipt and attach to the back page of this user guide.  
Customer Support  
Phone: 1300 889 785  
Australia  
Oricom International Pty Ltd  
Locked Bag 658  
South Windsor, NSW 2756  
Fax: (02) 4574 8898  

Printek Formsmaster 8000se User Manual
Ricoh Mp 3090 User Manual
Samsung Clp 315nkg User Manual
Sanyo Uf383450f User Manual
Sears 200713121 User Manual
Sharp Ar Nb3 User Manual
Solio Hybrid 1000 H1000 User Manual
Teledyne 730 Bubbler User Manual
Whirlpool Ace184xl0 User Manual
Xerox All In One Printer 6204 User Manual