Yamaha Projector DPX 1200 User Manual

DPX-1200

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation

Address: 6660 Orangethorpe Avenue

Buena Park, CA90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: Projector

Model Name: DPX-1200

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

See the user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (for US customers only)

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is

found to be the source of interference, which can be determined

by turning the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures:

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void

your authority, granted by the FCC, to use the product.

Relocate either this product or the device that is being affected

by the interference.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded

cables. Cable/s supplied with this product MUST be used.

Follow all installation instructions. Failure to follow

instructions could void your FCC authorization to use this

product in the USA.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe

Ave, Buena Park, CA 90620.

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will not

result in harmful interference with other electronic devices.

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the operation

of other electronic devices.

We WantYou Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or

distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend

you to avoid prolonged exposure from excessive volume levels.

Download from Www.Somanuals.com. All Manuals Search And Download.

Caution: Read this before operating this unit.

•

To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

•

When not planning to use this unit for a long period of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

Installation

•

When disconnecting the power cord from the wall outlet, grasp

the plug; do not pull the cable.

•

Install this unit in a well-ventilated, cool, dry, clean place with

at least 30 cm (1 feet) clearance on the top, right and left, and

at the back of this unit — away from direct sunlight, heat

sources, vibration, dust, moisture, and/or cold.

Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

Others

Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds. To prevent fire or

electrical shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

•

Clean the lens carefully so as not to create any scratches by

using a blower or lens paper.

•

Replace the lamp when the LAMP warning indicator blinks in

red after the lamp usage has exceeded 2000 hours. Follow the

lamp replacement procedure described in this manual.

Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an appropriate

3 pin plug fitted. For details, refer to the instructions described

below.

•

On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

Note

– Containers with liquid in them, as they may cause electrical

shock to the user and/or damage to this unit.

•

The plug severed from the mains lead must be destroyed, as a plug with

bared flexible cord is hazardous if engaged in a live socket outlet.

•

Do not cover this unit with a newspaper, tablecloth, curtain, etc.

in order not to restrict heat dissipation. If the temperature inside

this unit rises too much, it may cause fire, damage to this unit,

and/or personal injury.

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW: EARTH

BLUE:

BROWN:

When installing this unit on the ceiling, make sure the ceiling

has sufficient strength to support this unit and the ceiling

mounts for an extended period of time. Installation must be

performed only by qualified service personnel.

NEUTRAL

LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be

connected to the terminal in the plug which is marked by the letter

E or by the safety earth symbol or coloured GREEN or GREEN-

and-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

Operation

•

Remove the lens cover before starting any operation of this unit

to prevent the heat from staying around the lens. Operation

with the cap on may cause damage to this unit.

•

Do not plug in this unit to a wall outlet until all connections are

complete.

Only the voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than that

specified.

For Canadian customers

•

Do not use force on switches, knobs and/or cords.

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian ICES-

003.

Take care of this unit so that no foreign objects and/or liquid

drop inside this unit.

•

To prevent damage by lightning, disconnect the power cable

from the wall outlet during an electrical storm.

Do not look into the lens while this unit is turned on. It may

cause serious damage to your eyesight.

Before moving this unit, press STANDBY/ON to set this unit

in the standby mode, and disconnect the AC power plug from

the wall outlet.

•

Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed. The

cabinet should never be opened for any reason.

iii

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of contents

1 Getting started

Inappropriate places for installation........ 2

Accessory check .................................... 2

Getting started

Features

2 Features

3 Controls and functions

4 Remote control

5 Preparation

Controls and functions

Remote control

Preparation

Projection

6 Projection

Checking installation and connections...12

Turning the projector power on ............ 13

Selecting an input signal ...................... 15

Adjusting the image ............................. 20

7 Menu

Menu configurations............................. 22

Menu items .......................................... 23

Menu operations .................................. 32

Memory function

Connection

Installation

8 Memory function

(Saving, Recall, Lock, Copy, Reset)

9 Connection

Connecting to AV components............. 48

Connecting to computer devices.......... 49

10 Installation

Reference

Setting up the DPX-1200 ..................... 50

Projection distance ............................... 51

Projection image position ..................... 52

11 Reference

Glossary ............................................... 53

Compatible signal types ....................... 55

Maintenance......................................... 56

Troubleshooting.................................... 58

Message display .................................. 60

LED Indicator meanings ....................... 61

Specifications ....................................... 62

Dimensional drawing ............................ 63

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Getting started

NInappropriate places for installation

If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the unit itself. Carefully choose the place

to install this unit by avoiding the places listed below.

1. Places where the temperature and humidity vary greatly

• Do not install this unit in a place where the temperature and humidity become extremely high or the temperature becomes extremely

low.

• This unit must be used within a temperature range of 5 to 35°C.

2. Places without adequate ventilation

• Install this unit with at least 30 cm (1 feet) of ventilation space on the top, right and left, and back.

• Do not cover the ventilation slots of this unit. Covering the slots will obstruct heat dissipation.

• Install this unit on the firm surface.

• Do not cover this unit with a tablecloth, etc.

• Make sure there is nothing to get sucked into the ventilation slots so that the temperature of this unit does not become too high.

• If you are going to install the unit in a rack, be sure to leave space for ventilation to prevent exhaust overheating the unit.

3. Places where it gets dusty

• If the filter is blocked with dust, the temperature of this unit may become too high.

4. Places with too much vibration or impact

• Vibration and impact can damage parts of this unit.

5. Places where this unit gets exposed to water or high humidity

• If this unit is exposed to water or high humidity, it may cause a fire or electrical shock.

6. Unstable places

• If this unit is installed on an unstable or an inclined tabletop, it may fall and cause damage to the unit or personal injury.

7. In close proximity to a Radio or Stereo

• The unit may interfere with reception if placed in close proximity to a radio or television receiver.

Warning

•

To ensure vivid, high contrast images, make sure that no light other than the projector light falls directly on the screen.

NAccessory check

Please check that all accessories listed here are included in your package.

• Remote control

• Batteries (AA, UM-3 or R6)

• Power cable

• Trigger-out DC plug

(For USA only)

AUTO

V. POS

IRIS

ZOOM

FOCUS

PATT

SETTING

ESCAPE

• Pin/BNC adapters

• Lens cap

ASPECT

INPUT

HIDE

RESET

STILL

LIGHT

VIDEO

HDMI

VIDEO

INPUT

MEMORY

Download from Www.Somanuals.com. All Manuals Search And Download.

2 Features

Highly configurable electronic adjustment gives you the

freedom to place the projector wherever you want

A short focal length, high power zoom, and fully vertically adjustable lens allow you to use the

projector in a wide range of environments. You can also use the remote control to access many

lens functions such as focus, zoom, and lens shift to fine-tune the projector from your viewing

position.

Uses the DMD^TMdevice 720p DarkChip3^TM

The projector uses the high contrast “720p DarkChip3^TM”, to reduce black levels even further

and reproduce contrasts close to that of a film.

Adjust 7 colors independently (including white), or use the

automatic color balance function

The DPX-1200 allows you to adjust the 7-axis WRGBYCM color coordinate and gain

parameters directly. For better consistency, you can also control color temperature and RBG

balance together, allowing you to check that the changes you make are always consistent with

your preferences.

The digital interface provides sharp, detailed images

The DPX-1200 is equipped with an HDMI terminal, which is set to become the standard for the

coming generation of products. Connect to a DVD player or set-top box with a HDMI terminal

to receive digital image data directly, and enjoy completely digitally processed images.

Compatible with the content protection function of HDCP.

Intelligent memory functions

The DPX-1200 can store six image memory settings, called memory numbers, for each input

jack. For each memory number, you can set parameters for different input resolutions, and the

unit will switch to the appropriate parameters when it begins displaying an image of an

appropriate resolution. For example, the unit automatically changes display settings without

changing memory numbers when you change from watching a DVD to watching a HDTV

image for which you have set different image menu item parameters.

In-line menus for image adjustment

You can access image adjustment menu items at the touch of a button, and adjust images while

viewing them without opening the menu screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

3 Controls and functions

NMain unit <Front panel and controls>

Front remote control sensor

STANDBY/ON indicator

Lamp cover

Exhaust vent

Ventilation inlet

STANDBY/ON

Lens

ESCAPE

Lens cap

PATTERN

SETTING

Adjustable feet

Makes small adjustments to

the projection angle

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

DIGITAL CINEMA PROJECTOR DPX-1200

1 LED Indicators

The main unit is equipped with 5 indicators to display various states of operation. See page 61 for explanations of the LED indicator

meanings.

STANDBY/ON

A STANDBY/ON indicator

(There is also an LED on the front panel of the main unit.)

ESCAPE

B LAMP warning indicator

C COVER warning indicator

D TEMP warning indicator

E FAN warning indicator

PATTERN

SETTING

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

2 STANDBY/ON button

7 MENU button

Switches the unit between Standby and On (operational)

modes.

Switches the settings and adjustments menu display on and off.

8 SETTING button

3 ESCAPE button

Selects lens adjustment modes.

Exits from submenus.

9 INPUT button

4 PATTERN button

Switches the input signal selection menu display on and off.

Switches the built-in test pattern on and off.

0 Cursor buttons

5 ASPECT button

Use the h, g, +, - buttons for system operations, menu item

Turns the display aspect menu for the project image on and off.

selection, and changing system values.

(Enter) button

Sets values when the DPX-1200 is displaying the menu. When

the menu is not displayed, the DPX-1200 displays the in-line

image quality adjustment menu. (ꢀ page 40)

Download from Www.Somanuals.com. All Manuals Search And Download.

NMain unit <Rear panel / Connections>

Rear remote control sensor

OUT

HDMI

RS-232C

TRIGGER OUT

REMOTE

INPUT

RGB/YP^B

R/YCBC

D4 VIDEO

G/Y

B/PB/CB

R/PR/CR

HD/SYNC

VIDEO

1 INPUT B (D-sub 15 pin)

9 AC inlet

Receives component video and RGB (RGB/YPBPR/YCBCR)

Insert the supplied AC power cable here.

signals. Use a D-sub monitor cable to connect components to

this jack.

0 VIDEO (Pin Jack)

Receives composite video signals from the VIDEO output

jacks of other AV components. Use a video pin cable for these

connections.

2 D4 VIDEO (D jack)

Receives signals output from the D jacks of other AV

components. It is compatible with D1 - D4 formats.

q HDMI^TM(HDMI^TMjack)

Receives HDMI^TMsignals from computers or AV components.

3 - 7 INPUT A (BNC jacks)

Receive component video and RGB signals. Connect

component signal connectors from AV components to input

jacks 3 - 5, and RGB signal connectors from computers to

input jacks 3 - 7. Use BNC cables for these connections.

w REMOTE IN / OUT jack

Connect the remote control to the REMOTE IN jack if you

want to use it through a cable. The REMOTE OUT jack

outputs the signal received through the REMOTE IN jack

without any change.

3 G/Y

(G, or luminance signal)

4 B/P^B/CB (B, or color difference signal)

5 R/PR/CR (R, or color difference signal)

6 HD/SYNC (Horizontal sync signal, composite sync signal)

e RS-232C (D-sub 9 pin)

For use in servicing this unit.

7 VD

(Vertical sync signal)

r TRIGGER OUT

8 S VIDEO (Mini DIN jack)

Outputs control signals to external components. This output

provides a potential of 12 V/ maximum 200 mA when this unit

is projecting. Use the supplied trigger-out DC plug (for US

model only) to control external components.

Receives signals from S-VIDEO output jacks of other AV

components. Use an S-VIDEO cable for these connections.

Download from Www.Somanuals.com. All Manuals Search And Download.

4 Remote control

NRemote control functions

Buttons on the remote control with identical names to those on the main unit perform identical functions. When using the remote control,

point it at the remote control sensor on the front or back of the main unit from a distance of 7m (23 feet) or less.

1 Transmit indicator

Lights up when the remote control sends infrared signals to the

main unit.

2 AUTO button

Automatically sets the DPX-1200 to the best settings for the

type of signal it is currently receiving.

3 V.POS button

AUTO

Switches on or off the vertical adjustment mode for the entire

image.

V. POS

ZOOM

FOCUS

4 ZOOM button

Switches on or off the size adjustment mode for the image the

DPX-1200 is projecting.

IRIS

SETTING

PATT

5 IRIS button

ESCAPE

Switches on or off the lens iris change mode.

6 ESCAPE button

Exits from submenus.

7 Cursor buttons

Use the h ,g, +, - buttons to move the cursor within the on-

screen display.

8 ASPECT button

Turns the display aspect menu for the project image on and off.

ASPECT

RESET

INPUT

HIDE

9 RESET button

Resets all adjustable parameters to their default settings. Also

you can display information about this unit by pressing and

holding the button for five seconds while the menu screen is

not displayed.

STILL

LIGHT

0 STILL button

Stops a moving image, displaying a still of the image the DPX-

1200 is projecting. Press STILL again to cancel this effect.

S VIDEO

HDMI

q INPUT area

VIDEO

Selects the INPUT jacks directly.

INPUT

w MEMORY area

Calls stored memory (all parameter settings) directly.

MEMORY

button

Switches the unit between Standby and On (operational)

modes.

r FOCUS button

Switches on or off the focus adjustment mode for the image the

DPX-1200 is projecting.

t PATT (PATTERN) button

Switches on and off the built-in test pattern.

y MENU button

Switches on and off the settings and adjustments menu display.

(Enter) button

Sets values when the DPX-1200 is displaying the menu. When

the menu is not displayed, the DPX-1200 displays the in-line

image quality adjustment menu. (ꢀ page 40)

Download from Www.Somanuals.com. All Manuals Search And Download.

i INPUT button

Switches on and off the input signal selection menu display.

o LIGHT switch

Moving this switch lights the high-use AUTO (2), ESCAPE

(6), ASPECT(8) ,

(e), MENU (y), and INPUT (i)

FOCUS

buttons. The light disappears if you do not perform any

operation within 10 seconds.

-1

ASPECT

ID-2

INPUT

p HIDE button

HIDE

VIDEO

Temporarily halts projection of the image the DPX-1200 is

currently displaying. Press again to cancel this effect.

INPUT

MEMORY

a Remote control code switch

Selects ID-1 or ID-2 when operating two main units with one

remote control. You can set the ID for the main unit in the

menu (The default setting is ID-1).

s Remote control cable jack

Connect this jack and REMOTE IN jack on the main unit using

a cable (commercially available) to use the remote control with

a wired connection. (ꢀ page 8)

Download from Www.Somanuals.com. All Manuals Search And Download.

NLoading the batteries into the remote control

1. Remove the battery compartment cover.

2. Insert two batteries (AA, UM3, or R6 type), matching the polarity

markings on the batteries with those in the battery

compartment.

3. After loading the batteries, close the cover until it snaps into

place.

Warning

•

If the remote control must be used closer to the main unit than normal, or does not always operate correctly, exchange the

batteries for new ones.

•

Do not mix old and new, or different types of batteries.

Remove the batteries if you do not plan to use the unit for a long time.

If the batteries leak, dispose of them immediately, taking care not to touch the battery fluid. If the battery fluid comes into contact

with your eyes, mouth, or skin, rinse it off with water immediately and consult a doctor. Clean the battery compartment thoroughly

before installing new batteries.

NUsing the remote control with a wired connection

Use a 2P monaural miniplug cable (commercially available) to connect the remote control jack on the underside of the remote control to the

REMOTE IN jack on the main unit. Use the wired remote control configuration to control the DPX-1200 without having to be within range

of the remote sensor.

-1

LIGHT

INPUT

MEMORY

OUT

HDMI

RS-232C

TRIGGER OUT

REMOTE

INPUT

RGB/YP^B

PR/YCB

D4 VIDEO

G/Y

B/PB/CB

R/PR/CR

HD/SYNC

S-VIDEO

VIDEO

Download from Www.Somanuals.com. All Manuals Search And Download.

NLimits for using the remote control

Use the remote control within the following parameters. The remote control may not function correctly if you use it outside the limits

described here.

Distance to sensor

Angle to sensor

7 m

30˚ vertically and horizontally

(approximate value)

OUT

HDMI

REMOTE

RS-232C

TRIGGER OUT

INPUT

RGB/YP^BPR/YCBCR

G/Y

B/PB/CB

R/PR/CR

HD/SYNC

S-VIDEO

VIDEO

AUTO

POS

ZOOM

FOCUS

PATT

POS

ZOOM

FOCUS

PATT

IRIS

SETTING

IRIS

SETTING

ESCAPE

ASPECT

INPUT

HIDE

ASPECT

INPUT

HIDE

RESET

STILL

RESET

STILL

LIGHT

VIDEO

HDMI

VIDEO

HDMI

VIDEO

INPUT

MEMORY

Use within a left/right arc of 30 degrees

Use within a vertical arc of 30 degrees

Warning

•

Bright or fluorescent light on the main unit remote sensor may inhibit the functioning of the remote control.

Objects placed between the main unit remote sensor and the remote control may block the remote control signal and inhibit

functioning.

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparation

Before projection, install the main unit and a screen, connect the main unit to an AV component or computer, and adjust the projection image.

You can begin projection as soon as installation is complete.

Refer to the sections below for information on how to install the main unit to suit your viewing environment.

NIf you have not installed the main unit or screen

• Immediately after purchase, when you have not installed either the main unit or a screen.

• When moving the main unit and screen to a new location.

STEP4

projection image.

ꢀ page 22 - 40

• Use the menu to

adjust projection

details.

STEP 1 STEP2 STEP3

Adjust the

Install the main unit

and screen.

Connect AV

components or a

computer to the

main unit.

Select an image and

project.

Projection

preparations

complete

ꢀ page 50

ꢀ page 12 - 21

• The image is used

for adjusting the

image position

and focus.

ꢀ page 48

NIf you have installed the main unit and screen, but not connected

any image playback components

• You have installed the main unit and screen, but not connected any source components.

• You are using the main unit in a previously installed location, and wish to change the component you use as a signal source.

STEP2 STEP3

STEP4

projection image.

ꢀ page 22 - 40

• Use the menu to

adjust projection

details.

Connect AV

components or a

computer to the

main unit.

Select an image and

project.

Adjust the

Projection

preparations

complete

ꢀ page 12 - 21

• The image is used

for adjusting the

image position

and focus.

ꢀ page 48

NIf you have installed the main unit and screen, and connected a

source component

• You have installed the main unit and screen, and connected source components.

• You are using the main unit in a previously installed location with previously connected source components.

You do not need to carry out step 3 or step 4 if you

do not want to adjust the projection image. If the

unit does not project the image correctly, it may not

be connected correctly. In this case, carry out this

procedure starting from step 2.

STEP3

STEP4

projection image.

ꢀ page 22 - 40

• Use the menu to

adjust projection

details.

Select an image and

project.

Adjust the

Projection

preparations

complete

ꢀ page 12 - 21

• The image is used

for adjusting the

image position

and focus.

Download from Www.Somanuals.com. All Manuals Search And Download.

Step1

Set up the projector and screen

• Install the projector

• Install the screen ꢀ page 50

Step2

Connect an AV component or computer

• Connect AV components

• Connect a computer ꢀ page 48

Step3

Turn the power on and selecting an

image for projection

• Turn on the projector power

• Begin playback of the input image

• Select an input signal

• Select a projection image aspect

• Adjust the image

Focus/Vertical and Horizontal position/Size/Iris

ꢀ page 12 - 21

Step4

Only adjust these

parameters when

necessary. It is not

necessary to adjust these

settings once you have set

them initially.

Use the menu to adjust the image quality and

other parameters

• Image quality: Set image quality details

• Signal setting: Set input signal details

• Default settings: Set the default settings for everyday use

• Installation settings: Set to suit your viewing environment ꢀ page 22 - 40

Download from Www.Somanuals.com. All Manuals Search And Download.

6 Projection

Checking installation and connections

NPre-operation check

Prior to projection, adjust settings to suit the location of the main unit and screen, and the input signal you are using.

However, there is usually no need to adjust any settings if you have not changed the installation location or components since the last time

you used this unit. Check settings and connections only when the unit does not appear to project images correctly.

Prior to projection, check that the main unit and screen are correctly installed, and that source components are connected correctly.

Is the main unit power

turned on?

Main unit

Are the components connected correctly?

“Connecting to AV components”

ꢀ page 48

Image source component

Is the screen installed correctly?

“Setting up the projector and screen”

ꢀ page 50

PURE DIRECT

REC OUT/ZONE

SOURCE/REMOTE

VOLUME

MULTI JOG

BALANCE

DTV/LD

CABLE

DVD

MD/TAPE

SPEAKERS

MULTI CH

INPUT

DSP

PROGRAM

2CH/MULTI CH

VCR

CD-R

INPUT MODE

STRAIGHT

EFFECT

INPUT SELECTOR

TONE

CONTROL

TUNER

DVR

PHONO

VIDEO AUX

STANDBY

/ON

SILENT

OPTIMIZER

MIC

VIDEO AUX

PHONES

VIDEO

AUDIO

OPTICAL

Is the source component power

turned on?

To project images, carry out the following procedure.

Check installation and connections

Select an image for projection and image adjustment

Turn on the projector power.

Begin playback of the source image for adjustment.

Select a projection image.

(Select an input signal and projection image aspect.)

Adjust focus and vertical/ horizontal positioning.

Projection preparations complete

For an explanation of detailed settings, see “Menu”. ꢀ page 22 - 40

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning the projector power on

NTurning the power on

Always remove the lens cap before operating the main unit.

STANDBY/ON

1. Insert the supplied power cable

firmly into the AC inlet at the rear

of the main unit, then insert the

plug into an AC outlet.

STANDBY/ON

indicator

ESCAPE

PATTERN

SETTING

ASPECT

INPUT

The STANDBY/ON indicator lights orange.

LAMP

COVER

TEMP

FAN

OUT

HDMI

RS-232C

TRIGGER OUT

REMOTE

INPUT

RGB/YP^BP

R/YCBC

D4 VIDEO

G/Y

B/PB/CB

R/PR/CR

HD/SYNC

S-VIDEO

VIDEO

AC inlet

button STANDBY/ON button

2. Press the STANDBY/ON button

(the

button on the remote

control).

AUTO

V. POS

IRIS

STANDBY/ON

ZOOM

FOCUS

PATT

The indicator blinks green and the lamp

lights up in preparation for projection. After

approximately 35 seconds, the indicator

changes from blinking to solid green,

indicating that the unit is ready to project.

SETTING

ESCAPE

PATTERN

SETTING

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

ASPECT

INPUT

Warning

Remote Control

Main unit

•

Do not remove the power cable while the STANDBY/ON indicator is blinking green or

lit steady green.This could damage the lamp or reduce lamp life.

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning the projector power on

NPlacing the DPX-1200 in standby mode

button STANDBY/ON button

1. Press the STANDBY/ON button.

A confirmation message appears on the

screen.

AUTO

V. POS

IRIS

STANDBY/ON

ZOOM

FOCUS

PATT

Press again to enter standby.

SETTING

ESCAPE

PATTERN

SETTING

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

ASPECT

INPUT

Remote Control

Main unit

2. If you wish to place the DPX-1200

in standby mode, press the

STANDBY/ON button again.

The lamp changes to a half lit state, and the

fan activates for 2 minutes to cool the lamp.

During this time, the STANDBY/ON

indicator blinks orange, and pressing

STANDBY/ON does not turn main unit

power on again. When the unit finishes

cooling, the fan stops, and the STANDBY/

ON indicator turns orange.

Memo

•

The lamp may blink when half lit.This is not a defect.

Warning

AC inlet

•

Do not remove the power cable while the STANDBY/ON indicator is blinking green

or when the fan is activated.This could damage the lamp or reduce lamp life.

If you do not plan to use the main unit for a long period of time, attach the lens cap

and remove the plug from the AC outlet.

OUT

HDMI

RS-232C

TRIGGER OUT

REMOTE

INPUT

RGB/YP^BPR/YCBCR

D4 VIDEO

G/Y

B/PB/CB

R/PR/CR

HD/SYNC

S-VIDEO

VIDEO

Condensation may appear on the unit if the temperature of the surrounding

environment changes quickly. Condensation may also cause the projected image to

be cloudy. Place the unit in standby mode until the condensation disappears.

Switching the unit on when condensation is present may damage the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting an input signal

NSelecting using the INPUT button

Press the INPUT button to select an input signal from a source component. Choose from the following:

INPUT SIGNAL

VIDEO

Projection image signal

Selects component video signals received from AV components connected to the VIDEO jack.

Selects S-Video signals received from AV components connected to the S VIDEO jack.

S VIDEO

INPUT A

• Component

• RGB PC

• RGB TV

: Selects component signals received from the INPUT A BNC jacks.

: Selects RGB signals received from computers connected to the INPUT A BNC jacks.

: Selects RGB signals received from AV components connected to the INPUT A BNC jacks.

INPUT B

HDMI

• Component

• RGB PC

• RGB TV

: Selects component signals received from the INPUT B D-sub 15 pin jack.

: Selects RGB signals received from computers connected to the INPUT B D-sub 15 pin jack.

: Selects RGB signals received from AV components connected to the INPUT B D-sub 15 pin jack.

• Auto

: Signals input to the HDMI jack from AV components (automatically distinguishes between

component and RGB signals).

• Component

• RGB TV

: Selects digital component signals received from AV components connected to the HDMI jack.

: Selects digital RGB signals received from AV components connected to the HDMI jack.

D4 VIDEO

Selects component signals received from AV components connected to the D4 VIDEO jack.

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting an input signal

Remote cotrol

Main unit

1. Press the INPUT button.

Input signal

VIDEO

+ button

The input signal selection menu appears on

the display.

AUTO

S VIDEO

INPUT A

INPUT B

HDMI

STANDBY/ON

V. POS

IRIS

ZOOM

FOCUS

PATT

SETTING

ESCAPE

PATTERN

SETTING

button

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

ASPECT

INPUT

HDMI

RESET

STILL

2. Use the h or g buttons to select

an input signal, then press the

button.

Input signal

VIDEO

LIGHT

VIDEO

DVI

INPUT button

Cursor button

VIDEO

S VIDEO

INPUT A

INPUT B

HDMI

INPUT

MEMORY

Warning

•

You can select [Component], [RGB PC], or [RGB TV] for INPUT A and INPUT B, or

[Auto], [Component], or [RGB TV] for HDMI, from the submenu. If you do not select a

setting, the unit continues to use the setting from the last signal it received.To

change this setting, carry out the following procedure.

3. Press the + button to open the

submenu.

Input signal

VIDEO

S VIDEO

INPUT A

INPUT B

HDMI

The mark to the right of the input signal

name indicates that there is a submenu

available for selection.

4. Select an appropriate setting

from [Component], [RGB PC], or

Input signal

VIDEO

[RGB TV] and press the

to confirm the setting.

button

S VIDEO

INPUT A

INPUT B

HDMI

Component

RGB PC

RGB TV

Memo

•

If you set your laptop or notebook computer to display on its built-in display and on

an external monitor simultaneously, the main unit may not project the image

correctly. In this case, set your computer to display on the external monitor only.

Refer to your computer’s operating instructions for further details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting an input signal

NSelecting a display aspect for a projection image

The display aspect parameter sets the ratio of height to width the unit uses to project an image for an input signal.

Remote cotrol

Main unit

1. Press the ASPECT button.

Display Aspect Ratio

Auto

The display aspect selection menu appears

on the display.

cursor button

Normal

AUTO

STANDBY/ON

V. POS

IRIS

ZOOM

FOCUS

PATT

Squeeze

Smart Zoom

Zoom

SETTING

ESCAPE

PATTERN

SETTING

Special

Through

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

ASPECT

INPUT

HDMI

RESET

STILL

ASPECT

button

2. Use the h or g button

LIGHT

Display Aspect Ratio

Auto

VIDEO

DVI

to select a suitable display aspect

VIDEO

setting, then press the

button.

Normal

INPUT

button

MEMORY

Squeeze

Smart Zoom

Zoom

If you select [Special] or [Through],

pressing the + button displays the submenu.

Special

Through

Memo

•

The display aspect you can use depends on the current input signal. When the input

signal contains display aspect information, set the display aspect parameter to

[Auto] to detect the appropriate display aspect setting automatically.

You can also use the [Display Aspect Ratio] page in the menu screen to select a

display aspect. (ꢀ page 22- 40)

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting an input signal

Memo

•

Refer to the glossary for explanations of terms such “letterbox” or “squeeze”. (ꢀ page 53)

Auto

Special

Detects information encoded in letterbox or squeeze type input

Subtitle Zoom

signals and automatically selects an appropriate display aspect.

Depending on the input source, the unit may not change to the

most appropriate mode. In this case, manually select a suitable

setting.

The best format for projecting subtitled letterbox format

software. See page 38 for the o ,Cperational procedure.

• Subtitle area: Adjust the area used to display subtitles on

screen.

• V Scroll: Adjusts the vertical position of the subtitles.

Normal

Cinema Zoom

Projects images with their original display aspect. Depending

on the input signal, black areas may appear to the left and right

of the image.

Removes the black bar from Cinescope size screens (2.35:1) to

display a full horizontal image, cutting both screen sides.

There are two types: SDTV for 4:3 images, and HDTV for

16:9 images.

Squeeze

Returns horizontally compressed images to their original

aspect. Use this mode to display horizontally squeezed images

in a normal wide aspect manner.

Cinema Squeeze

Removes the black bar from cinescope size screens for 4:3

images and resize the vertical image so that a 16:9 panel

resolution is fully displayed, cutting both screen sides.

Smart Zoom

14:9 Zoom

Stretches the left and right edges of a 4:3 image without

altering the image center, to project a 16:9 image that fills the

screen.

Displays 14:9 images with a full vertical aspect, retaining the

black area at either side of the screen.

Through

Zoom

Normal Through

Projects images the unit receives in letterbox format as 16:9

images that fill the screen.

Projects images without stretching or reducing them. The size

of the projection image depends on the resolution of the image

received.

Squeeze Through

Widens the image received to project it with a 16:9 aspect

ratio. The size of the projection image depends on the

resolution of the image received. This mode is not available for

RGB PC input signals.

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting an input signal

Input signal type

Input image

Display aspect

Projected image

Normal

Standard 4:3 image

Smart Zoom

Zoom

Letter box

Subtitle Zoom

Cinema Zoom

Squeeze

SUBTITLE

Squeeze

Cinema Squeeze

14:9 Zoom

Normal

14:9 image

Normal

HDMI

Cinema

Scope

Cinema Zoom

Normal

RGB PC

Normal

Normal Through

Squeeze Through

All

Squeeze

Download from Www.Somanuals.com. All Manuals Search And Download.

Select an image for projection

Adjusting the image

Carry out the following adjustments to obtain optimal projection conditions.

Using test patterns to adjust the projection image – PATT button

The DPX-1200 is equipped with three test patterns, the crosshatch pattern necessary for focus and keystone adjustment, and the grayscale

and color bar patterns necessary for adjusting image quality.

Crosshatch pattern

1. Press the PATT button on the

remote control, or the PATTERN

button on the main unit.

AUTO

V. POS

IRIS

ZOOM

FOCUS

PATT

2. Press the + or - button to select

the necessary pattern.

SETTING

PATT

button

ESCAPE

Grayscale pattern

Color bar pattern

3. To exit from the test display,

press the PATT or PATTERN

button.

STANDBY/ON

PATTERN button

ESCAPE

PATTERN

SETTING

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

N Adjusting the vertical position – V.POS button

If the center of the screen is not in line with the center of the lens of the DPX-1200, use the V.POS button to adjust the position of the image

up or down. You can adjust the image to a maximum of half of the height of the projection screen.

1. Press the V.POS button on the

remote control, or press the

AUTO

SETTING button on the main unit

repeatedly to select [Lens Shift]

from the display menu.

V. POS

IRIS

ZOOM

FOCUS

PATT

V.POS

button

SETTING

Lens Shift

ESCAPE

2. Press the h or g button to move

the projected image to a suitable

place.

STANDBY/ON

ESCAPE button

3. To exit from the adjustment

mode, press the V.POS or

ESCAPE button.

ESCAPE

SETTING

button

SETTING

PATTERN

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the image

N Adjusting the size of an image – ZOOM button

Enlarge or reduce the size of the projection image to match the size of the screen. The zoom ratio is 1:1.6.

1. Press the ZOOM button on the

remote control, or press the

ZOOM

button

AUTO

SETTING button on the main unit

repeatedly to select [Zoom] from

the display menu.

V. POS

IRIS

ZOOM

FOCUS

PATT

SETTING

Zoom

ESCAPE

2. Press the h or g button to adjust

the image to a suitable size.

STANDBY/ON

ESCAPE button

3. To exit from the adjustment

mode, press the ZOOM or

ESCAPE buttons.

ESCAPE

SETTING

button

SETTING

PATTERN

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

N Adjusting the image focus – FOCUS button

Adjust the focus of the on-screen image.

1. Press the FOCUS button on the

remote control, or press the

AUTO

SETTING button on the main unit

repeatedly to select [FOCUS]

from the display menu.

V. POS

IRIS

ZOOM

FOCUS

PATT

FOCUS

button

SETTING

Focus

ESCAPE

Memo

STANDBY/ON

•

When you want to use the test pattern

to adjust image focus press the PATT

button on the remote control, or the

PATTERN button on the main unit

before carrying out step 1.

ESCAPE button

ESCAPE

SETTING

button

SETTING

PATTERN

2. Press the h or g button to adjust

ASPECT

INPUT

the focus of the projected image.

LAMP

COVER

TEMP

FAN

3. To exit from the adjustment

mode, press the FOCUS or

ESCAPE buttons.

N Adjusting the iris setting – IRIS button

Press the g button to reduce the aperture of the iris for increased black levels and contrast, or the h button to increase aperture to obtain a

brighter image.

1. Press the IRIS button on the

remote control, or press the

AUTO

SETTING button on the main unit

repeatedly to select [IRIS] from

the display menu.

V. POS

IRIS

ZOOM

FOCUS

PATT

IRIS

button

SETTING

Iris

ESCAPE

2. Press the h or g button to adjust

the iris setting for the projected

image.

STANDBY/ON

ESCAPE button

3. To exit from the adjustment mode,

press the IRIS or ESCAPE button.

ESCAPE

SETTING

button

SETTING

PATTERN

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu

Menu configurations

Configure the DPX-1200 to suit your viewing environment by adjusting image quality, initial settings, defaults, and setup characteristics.

These parameters can be accessed through the menu.

Press the MENU button on the remote control or the main unit to display the menu screen. The menu consists of the [Image], [Signal],

[Initial], and [Setup] menu groups, each containing numerous items you can use for configuring the unit. Note that some items are only

selectable for certain types of input signal (Video, Component, RGB TV, RGB PC).

Menu groups appear in the upper area of the display, as the top level of menu composition. Menu items appear in the left area of the display.

You can select settings and make adjustments to suit your preferences. See page 32 - 40 for an explanation of how to use the menu.

NMenu screen

<Example:When in advanced mode>

[Move Menu Window] area

Use this selection area to move

menu screens. See page 37 for

more information.

Move Menu Window

Initial

Menu group

Image

Signal

Setup

[Image] selected.

Black Level

White Level

Gamma

Hue

Menu items

Saturation

100

Items displayed here depend on

the menu group you select.

The picture on the right shows

menu items in the [Image] group

for example.

Parameter adjustment area

Sharpness Type

Sharpness Gain

Color Adjustment

White Peaking

Iris

Off

WRGB

6500K 0.000uv

Level Adjustment

Input jack display area

Shows the currently selected

input jack.

Memory 1

VIDEO

Menu operation guide

Displays helpful instructions when

special operations are necessary.

Memory number status

Displays the currently selected memory number and memory status. Change

the memory number and lock/unlock memory settings here(ꢀ page 41-43).

Some menu items contain an additional level of items called a submenu. Moving the cursor to an item with a submenu attached displays “

to the right of the item name. Some submenus contain further levels of submenus containing items for selection.

”

Move Menu Window

Initial

Move Menu Window

Initial

Image

Signal

Setup

Image

Signal

Setup

Black Level

White Level

Gamma Trim

Hue

Color Temp.

6900K 0.005uv

Indicates the existence of a submenu

–

0.4

Saturation

100

0.35

0.5

Sharpness Type

Sharpness Gain

Color Adjustment

White Peaking

Iris

Off

0.02uv

0.3

Standard

67000K 0.0005uv

0.00uv

Color Adjustment

Standard

WRGB

6700K 0.000uv

–

0.02uv

6500K 0.000uv

0.0

0.25

0.5

WRGBYCM

6500K 0.000uv

0.25

0.3

0.35

Level Adjustment

[Color Adjustment] submenu

+ : Enter

Memory 1

VIDEO

Memory 1

VIDEO

: Edit

[WRGB] submenu

In this example, the menu contains three submenus, and one of the submenus contains a further submenu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

NMenu item list:

There are two types of menu, [Basic Mode] and [Advanced Mode].

• Basic mode: The menu displays menu items that are frequently used or absolutely necessary to image projection.

• Advanced mode: The menu displays all menu items, allowing you to carry out detailed adjustments.

You can change between the menu modes using the [Menu Mode] setting in the [Setup] menu group.

G Image

G Signal

G Initial

G Setup

Black Level (Brightness)

White Level (Contrast)

Gamma

Display Aspect Ratio

Setup Level (SDTV)

Setup Level (HDTV)

Signal Status

Color System

INPUT A Signal

INPUT B Signal

HDMI Signal

Display Language

Lamp Running Time

Reset

Location

Keystone Correction

Lens Adjustment Lock

Menu Color

Hue

Saturation

Menu Mode

Color Temp

White Correction

Sharpness Type

White Peaking

G Image

G Signal

G Initial

G Setup

Black Level (Brightness)

While Level (Contrast)

Gamma

Display Aspect Ratio

Color System

Location

Overscan

INPUT A Signal

INPUT A Sync Type

INPUT B Signal

INPUT B Sync Type

HDMI Signal

Keystone Correction

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

Lamp Power

3D Y/C separation

Noise Reduction

Video Type

Hue

Saturation

Sharpness Type

Sharpness Gain

Color Adjustment

White Peaking

Iris

Progressive Mode

Color Space Conversion

Setup Level (SDTV)

Setup Level (HDTV)

Clamp Position

Auto Power Off

Auto Input Search

Display Language

Lamp Running Time

Reset

Menu Color

Menu Mode

Message

Trigger Out

Level Adjustment

Sync Adjustment

Tracking

Baud Rate

Horiz. Display Position

Vert. Display Position

Signal Status

Memo

• Menu items you can choose may differ depending on the input signal type.

• Items in the menu that contain submenus are marked with “ ”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

The submenus display different items depending on the input signal. Items in submenus that contain further submenus are marked with “ ” .

G Image

G Signal

G Initial

G Setup

1: Color Adjustment

3: Display Aspect Ratio

5: Color System

9: Location

Standard

Auto

Front/Table

Front/Ceiling

Rear/Table

Rear/Ceiling

10: Remote Control Sensor

Front & Rear

Front

WRGB

Normal

NTSC

WRGBYCM

2: Level Adjustment

Y Offset

Squeeze

NTSC4.43

PAL

Smart Zoom

Zoom

PAL-M

Cb Offset

Cr Offset

Y Gain

Special

PAL-N

Through

PAL60

4: Signal Status

Resolution

Sync Type

Sync Polarity

Frequency

SECAM

Rear

Cb Gain

6: All Input Signals

Component

RGB PC

Off

Cr Gain

11: Remote Control ID

ID 1

RGB TV .etc

7: Display Language

ID 2

Source Equipmet (HDMI only)

12: Menu Color

Monotone

Color

English

Deutsch

Español

Français

Italiano

13: Trigger Out

Lamp

Fan

RS-232C

Portuguêsa

8: Reset

All Settings

All Memory

Current Memory

1 Standard

2 WRGB

3 WRGBYCM

• Color Temp.

• Color selection screen

Color coordinate

Gain

• Color selection screen

Color coordinate

Gain

4 Special

5 Through

6 Monotone

7 Color

• Subtitle Zoom

Subtitle Area

V Scroll

(For video type input signal)

• Normal Through

• Menu Brightness

• Menu Contrast

• Menu Brightness

• Menu Contrast

• Color Style

• Squeeze Through

• Cinema Zoom

• Cinema Squeeze

• 14:9 Zoom

Memo

•

In addition to color temperature adjustment, the color coordinates and gain adjustment for each color may be carried out at the

[WRGB] and [WRGBYCM] color selection screen. Refer to page 36 for more information.

You can select [Subtitle Area] and [V Scroll] from the [Subtitle Zoom] menu item. See page 38 and 39 for more information.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

NMenu group items and functions

Memo

•

You can only select items displayed with a

in advanced mode.

<Image>

You can adjust the image when the unit is receiving an input signal.

Adjusts the level of darkness (black level) in an image.

Adjusts the level of darkness without altering peak whiteness levels.

Black Level

(Input signal)

• + side (0 to +50):

Video/S-Video/Component/RGB TV

White

Increases the luminance of dark scenes,

increasing the clarity of shading, but

reducing contrast.

• - side (-50 to 0):

Output signal

Weakens dark scenes, increasing image

contrast while reducing the clarity of black

shading.

Black

Input signal White

Adjusts the bright areas (white level) in the image.

Changes the brightness of an image without altering the brightness of the black areas of the

image.

White Level

(Input signal)

Video/S-Video/Component/RGB TV

• + side (0 to +50):

Increases the brightness of white areas in

White

the image, increasing contrast clarity, but

rendering white shadings difficult to see.

Output signal

• - side (-50 to 0):

Reduces the contrast of images.

Black

Input signal White

Adjusts the overall brightness of the image.

• Increase luminance (0 to +100):

Setting this figure too high results in a

white saturated image without any black.

• Decrease luminance (-100 to 0)

Setting this figure too low darkens the

entire image.

Brightness

(Input signal)

RGB PC

White

Output signal

Black

Input signal White

Adjusts the bright areas (white level) in the image.

Changes the brightness of an image without altering the brightness of the black areas of the

image.

• + side (1.00 to 1.50):

Increases the brightness of white areas in

Contrast

(Input signal)

RGB PC

white level

White

the image, increasing contrast clarity, but

rendering white shadings difficult to see.

Output signal

• - side (0.50 to 1.00):

Reduces the contrast of images.

Black

Input signal White

Changes the way the unit responds to changes in the shadings and color

Gamma

(Input signal)

tones of the image.

Video/S-Video/Component/RGB TV/RGB PC

The unit supplies 10 types of patterns for dealing with these changes. (ꢀ page39)

• A-E Provides the same sense of contrast as an ordinary TV monitor. Dark sections

become more muted in the order A

Provides richer expression of gradations in dark sections. Dark sections become

more muted in the order a e.

• a-e

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

Sets the hue or phase of the image.

• + side (0 to +50) : Shifts the hue towards blue coloration.

• - side (-50 to 0) : Shifts the hue towards red coloration.

Hue

(Input signal)

Video/S-Video/Component/RGB TV

Adjusts the degree to which color depth is expressed in the image.

• + side (+100 to + 200) : The unit projects colors with greater depth.

Saturation

(Input signal)

• - side (0 to +100)

: The unit projects colors with less depth.

Video/S-Video/Component/RGB TV

Adjusts color temperature.

Color Temp.

Adjusts the level of white in colors between red and blue, and between green and magenta.

Increase the color temperature to increase the amount of blue in an image, giving bright

color tones. Reduce the color temperature to increase the amount of red, giving a darker,

more relaxed atmosphere to the image.

(Input signal)

Video/S-Video/Component/RGB TV/RGB PC

Adjust in the [Color Adjustment] menu in

advanced mode.

Choices: 5,000 to 10,000

Color temprature

adjustment

Adjusts hUV.

White Correction

Increasing the hUV setting increases the amount of green in the image. Decreasing this

setting increases the amount of magenta.

Choices: -0.02 to +0.02

(Input signal)

Video/S-Video/Component/RGB TV/RGB PC

Adjust in the [Color Adjustment] menu in

advanced mode.

hUV

–

Changes the characteristics of the filter used for “Sharpness Gain”

Sharpness Type

(Input signal)

(described below).

Video/S-Video/Component/RGB TV

Choices: Off / L / ML / MH / H

Adjusts the clearness of the image edges.

Sharpness Gain

(Input signal)

Increase this figure to render a sharper image, or reduce it to give a softer image with less

image noise. You cannot adjust this parameter if [Sharpness Type] is set to [Off].

Choices: 0 to 10

Video/S-Video/Component/RGB TV

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

Adjusts color balance.

Color Adjustment

There are three menus, [Standard], [WRGB], and [WRGBYCM], separated in order of

complexity from simple to detailed. By the default setting, the DPX-1200 automatically

selects BT709 (RGB color coordinate for High-Definition Television) for HDTV (High-

Definition Television) or PC video input and BT601 (RGB color coordinate for Standard

Television) for SDTV (Standard Television) input. Refer to page 36 for parameter operation

methods.

(Input signal)

Video/S-Video/Component/

RGB TV/RGB PC/D4 VIDEO

The present color temperature setting is displayed to the right of the menu items.

Color Adjustment

Standard

6700K 0.000uv

The current color temperature is displayed.

- Standard

Adjusts color temperature and hUV only.

hUV adjusts values within the maximum

color temperature limits of the projector.

0.5

W (Color temperature

and h UV)

0.0

0.5

- WRGB

Adjusts the color coordinates and gain for

the three primary colors, R(Red), G(Green),

and B(Blue). The unit sets the complemental

colorsY(Yellow), C(Cyan), and M(Magenta)

automatically.Adjusting[ColorTemp.]resets

the RGB gain based on color coordinate

settings.Adjusting[Gain]resets[Colortemp.]

based on color coordinate settings.

G (Green)

0.5

W (Color temperature

and h UV)

R (Red)

B (Blue)

0.0

0.5

- WRGBYCM

G (Green)

Y (Yelow)

Adjusts the color coordinates and gain for

each component color individually. Press

the RESET button on the remote control

when the WRGBYCM menu is open to

automatically adjust the RGB gain and

YCM color coordinates and gain based on

the color temperature and RGB color

settings. When you have selected

WRGBYCM in the color adjustment

submenu, press RESET to automatically

adjust the RGB gain and YCM color

balance to the most appropriate setting,

based on color temp and RGB color

balance settings.

C (Cyan)

0.5

0.0

W (Color temperature

and h UV)

R (Red)

M (Magenta)

0.0

0.5

B (Blue)

Choices: White correction : -0.02 to +0.02

Color temperature : 5,000 to 10,000

Gain

: 0.00 to 1.99

Enhances the brilliance of the white portions of the projected image.

Choices: 0 to 5

White Peaking

Iris

Adjusts the iris (Optical).

You can select 3 levels.

(Input signal)

Video/S-Video/Component/RGB TV/RGB PC

Open

Adjusts the analog input signal gain and offset settings.

Adjust the gain and offset for component and RGB (Y, C^B, CR/R, G, B) input signals.

Choices: -50 to 0 to +50 (except for HDMI signals)

Level Adjustment

(Input signal)

Component/RGB TV/RGB PC

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

N Signal

You can adjust the image when the unit is receiving an input signal.

Sets the aspect ratio for projecting an image from an input signal.

See “Selecting a display aspect for projecting images”, page 17.

Display Aspect Ratio

(Input signal)

Video/S-Video/Component/RGB TV/RGB PC

Overscans video input sources for display.

Overscan

(Input signal)

Selects from [Standard] and [Full]. This parameter is not available when you select [Smart

Zoom] in [Display Aspect]. In some cases, noise may appear at the edges of the image

when you select [Full].

Video/S-Video/Component/RGB TV

• [Standard] : approximately 94% video output ratio

• [Full]

: approximately 100% video output ratio

Adjusts the quality of images input from VIDEO jack.

Suppresses the rainbow-like color and annoying dots in images. This function is only

available for NTSC format signals the unit receives at its composite input jacks.

Choices: On/Off

3DY/C Separation

(Input signal)

Video(NTSC)

Reduces noise in analog images.

Noise Reduction

Digital processing eliminates noise in the luminance and color signals from sources with a

comparatively large amount of noise, producing a more vivid image. Use when the quality

of the source you are viewing requires it.

(Input signal)

Video/S-Video/Component/RGB TV

Choices: Off/1/2/3

Selects the correct type of device to ensure image synchronization.

Select [VCR] when using an analog video tape as a video source. Select [DVD] for other

sources.

Video Type

(Input signal)

Video/S-Video

Switches the interlace/progressive (I/P) conversion mode.

Changes from Interlace/Progressive (I/P) conversion mode to [Auto] or [Video] mode.

(Only for SDTV interlaced signal).

Progressive Mode

(Input signal)

Video/S-Video/Component/RGB TV

• [Auto] : Detects t he film source automatically and projects it progressively.

• [Video]: Turns the detection function off.

Selects color space coefficients.

Color Space Conversion

• [Auto] : Selects the best color space coefficient for the image resolution.

• [SDTV] : Color space coefficient for BT.601 type signal.

• [HDTV] : Color space coefficient for BT.709 type signal.

(Input signal)

Video/S-Video/Component

Compensates for differences in the black levels of SDTV images.

• For signals equal to the pedestal level : Set to [0%].

• For signals with high levels of blackness : Set to [7.5%].

Setup Level (SDTV)

(Input signal)

Video/S-Video/Component/RGB TV

100

PEDESTAL LEVEL

BLACK LEVEL

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

Compensates for differences in the black levels of HDTV images.

Usually, choose [0%].

• For signals equal to the pedestal level : Set to [0%].

• For signals with high levels of blackness : Set to [7.5%].

Setup Level (HDTV)

(Input signal)

Component/RGB TV

100

PEDESTAL LEVEL

BLACK LEVEL

Regulates flickering, noise, and disorder in the image.

Choices: -128 to +127

Sync Adjustment

(Input signal)

RGB PC (except for HDMI signals)

Regulates vertical striping in the image.

Choices: 0 to 31

Tracking

(Input signal)

RGB PC (except for HDMI signals)

Adjusts the clamp position for analog video sources.

Choices: -30 to +30

Clamp Position

(Input signal)

Component/RGB TV

Adjusts the horizontal display position of the image.

Choices: PC type : -50 to 0 to +50

Horiz. Display Position

Video type : -10 to 0 to +10

(Input signal)

RGB PC (except for HDMI signals)/

Component/RGB TV

Adjusts the vertical display position of the image.

Choices: PC type : -50 to 0 to +50

Video type : -5 to 0 to +5

Vert. Display Position

(Input signal)

RGB PC (except for HDMI signals)/

Component/RGB TV

Displays the resolution of the image signal the unit is receiving.

Sync signal information for RGB type inputs is also displayed.

Signal Status

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

N Initial

Selects the color system to use for video input signals.

Usually, set this parameter to Auto to have the unit automatically detect the signal and

select an appropriate color system. Set the unit manually to view NTSC4.43 images as it

cannot detect NTSC4.43 automatically.

Color System

Choices: Auto/NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60/SECAM

Selects the type of input signal received at INPUT A.

Choices: Component/RGB PC/RGB TV

INPUT A Signal

Selects the sync type for signals received at INPUT A.

This function is only available for RGB TV.

INPUT A Sync Type

Choices: Auto/Separate Sync/Composite Sync/Sync on Green

Selects the signal type received at INPUT B.

Choices: Component/RGB PC/RGB TV

INPUT B Signal

Selects the sync type for signals received at INPUT B.

This function is only available for RGB TV.

INPUT B Sync Type

Choices: Auto/Separate Sync/Composite Sync/Sync on Green

Selects the signal type received at the HDMI jack.

Choices: Auto/Component/RGB TV

HDMI Signal

If the signal the unit is currently receiving stops and you do not perform any

operations for 30 minutes or more, the unit automatically places itself in

Auto Power Off

standby mode.

Choices: On/Off

Automatically changes inputs when the unit does not receive a signal.

If the signal the unit is currently receiving stops, or the input signal you selected the last

time you used the unit does is not available when you turn the unit power on, it

automatically searches through inputs for a signal in the following order.

Auto Input Search

INPUT A

Choices: On/Off

INPUT B

D4 VIDEO

S VIDEO

VIDEO

HDMI

Selects the language used in the menu display.

Display Language

Lamp Running Time

Reset

Choices:

/English/Deutsch/Español/Français/Italiano/Portuguêsa/

Displays the total lamp running time.

Opens the submenu to reset the running time. See page 38 for the operational procedure.

Resets menu parameters to their default setting.

Resets all menu parameters to their default setting, and return the configurations stored in

the memory to their defaults. See page 37, 46 and 47 for the operational procedure.

• [All Settings]

: Return all settings in the [Initial] and [Setup] menu groups in the

main menu, and all configurations stored by the memory function, to

their default settings.

• [All Memory]

: Return all configurations stored by the memory function to their

default settings.

• [Current Memory] : Return the currently selected memory configuration (corresponding

to the signal input from the currently selected input jack) to its

default setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu items

N Setup

Designate the location of the main unit.

Choices: [Front/Table] [Front/Ceiling] [Rear/Table] [Rear/Ceiling] (ꢀ page 50)

Location

Adjusts the projection angle of the image.

Keystone Correction

If you do not install the projector at right angles to the screen, the image will be trapezoidally

distorted. You can electronically correct this distortion using the keystone function to adjust the

width without changing the height of the image. Increase the keystone value (0 to 100) when the

top of the image is overly wide, and reduce it (-100 to 0) when the lower part is overly wide.

When the upper part of

the image is wider than the lower

When the lower part of

the image is wider than the top

Increase the value

in the positive (+) direction

Decrease the value

in the negative (-) direction

Sets the remote control sensor.

Remote Control Sensor

Remote Control ID

The main unit has two remote control sensors, one on the front panel and one on the rear,

which this setting allows you to switch between. The remote control functions regardless

of the setting of this parameter if you use a wired connection to connect it to the main unit.

Choices: Front & Rear/Front/Rear/Off

Sets the remote control ID.

Selects ID1 or ID2 for each main unit when operating two main units with one remote

control. You can select the controllable main unit with the remote control code switch on

the remote control.

Choices: ID1/ID2

Locks the lens adjustment function.

Locks the lens so that you cannot change the V.POS, ZOOM, and FOCUS settings

accidentally when set to [ON]. Set to [OFF] to cancel this function.

Lens Adjustment Lock

Lowers the power supply to the lamp.

You can adjust the power supplied to the lamp within the range of 80 to 100%.

Lamp Power

Menu Color

Selects the color of the letters and background the main unit uses to display

the menu on screen.

You can choose to display the menu screen in [Monotone] or [Color]. Also, you can adjust

the contrast and brightness of the menu from the [Menu Brightness] and [Menu Contrast]

menus. You can select from 3 color types.

Monotone

Menu Brightness

Menu Contrast

Color

Menu Brightness

Menu Contrast

Color Style

Switches menu modes between an easy-to-use basic mode and a detailed

Menu Mode

Message

advanced mode.

Choices: Basic/Advanced

Selects whether to display memory number, input signal and other

information on the projection screen. (ꢀ page 60)

Choices: On/Off

Sets the TRIGGER OUT terminal.

Trigger Out

Set the external control TRIGGER OUT jack 12 V signal emission to [Lamp] to

synchronize it to the ON/OFF state of the lamp, to [Fan] to synchronize it to the fan, and to

[RS-232C] to receive ON/OFF signals through the RS-232C terminal.

Choices: Lamp/Fan/RS-232C

Baud Rate

Sets the transmission speed of the RS-232C terminal.

This setting becomes valid from the next time you switch the unit on.

Choices: 9600bps/19200bps/38400bps/57600bps/115200bps

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu operations

NOperation button functions

Use the buttons on the remote control or the main unit to operate the menus. The button functions are listed below.

Remote Control

1 Menu Button

Opens/Closes the menu.

2 Cursor button

+ / - (Move the cursor ringht/left)

AUTO

• Selects menu groups.

• Opens/Closes submenus.

V. POS

IRIS

ZOOM

FOCUS

PATT

• Selects/Changes settings.

h / g (Moves the cursor up/down)

• Selects menu items.

SETTING

• Selects/Changes settings.

ESCAPE

button

• Confirms setting changes.

• Opens the in-line menu when the menu is not open.

• Selects special menu items (ꢀ page 36) and memory operation. (ꢀ page 41)

4 ESCAPE button

ASPECT

RESET

INPUT

HIDE

• Returns the cursor one level up the menu (e.g. From the menu item level to the menu

group level).

• Closes submenus.

• Closes the menu screen when the cursor is in a menu group.

• Returns from the menu movement bar to the menu entry screen, after moving a menu.

STILL

LIGHT

S VIDEO

HDMI

5 RESET button (Remote control only)

Returns parameters back to their default settings (Does not affect items with no default

setting).

VIDEO

INPUT

MEMORY

STANDBY/ON

Main Unit

ESCAPE

PATTERN

SETTING

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu operations

NMenu operations 1 (with no submenu)

Menu operations use the procedure below to adjust menu item without submenus.

Select a menu group (Image / Signal / Initial / Setup)

(Select with the +/- buttons)

Menu items related to the selected menu group are displayed.

Select an item to adjust or a setting

(Select with the h / g buttons)

You can now adjust the selected item.

Choose a setting for the selected item

(Usually, use the +/- buttons)

MENU Button

1. Press the MENU button to open

the menu screen.

Move Menu Window

Initial

Image

Signal

Setup

AUTO

V. POS

STANDBY/ON

Black Level

White Level

Gamma Trim

Hue

ZOOM

FOCUS

PATT

IRIS

SETTING

ESCAPE

PATTERN

SETTING

Memo

Saturation

100

Sharpness Type

Sharpness Gain

Color Adjustment

White Peaking

Iris

Off

ASPECT

INPUT

•

If you have opened the menu screen

previously, the menu displays the

settings from the last time you used it.

LAMP

COVER

TEMP

FAN

ASPECT

INPUT

WRGB

6500K 0.000uv

Remote Control

Main Unit

Level Adjustment

Memory 1

VIDEO

2. Press the + or - button to select a

menu group..

Move Menu Window

Initial

Image

Signal

Setup

Location

Front / Table

Keystone Correction

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

Lamp Power

Front & Rear

The illustration at right depicts the [Setup]

group being selected.

ID 1

Off

Remote Control

Main Unit

105

Menu Color

Monotone

Basic

Menu Mode

Advance

Message

Off

Trigger Out

Lamp

Baud Rate

115200bps

Memory 1

VIDEO

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu operations

3. Press the h or g button to move

the cursor to the item you wish to

adjust..

Move Menu Window

Initial

Image

Signal

Setup

Location

Front / Table

Keystone Correction

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

Lamp Power

Front & Rear

ID 1

Off

The illustration at right depicts [Lens

Adjustment Lock] being selected.

Remote Control

Main Unit

105

Menu Color

Color

Menu Mode

Basic

Advance

Message

Off

Trigger Out

Lamp

115200bps

Baud Rate

Memory 1

VIDEO

4. Press the + or - button to select a

suitable setting..

Move Menu Window

Initial

Image

Signal

Setup

Location

Front / Table

Keystone Correction

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

Lamp Power

Front & Rear

The illustration at right depicts the [Lens

Adjustment Lock] mode set to [On].

ID 1

Off

Remote Control

Main Unit

105

Memo

Menu Color

Monotone

Basic

Menu Mode

Advance

•

The setting method depends on the

item selected.

Message

Off

Trigger Out

Lamp

Baud Rate

115200bps

Memory 1

VIDEO

5. Move to another item or group as

necessary.

Memo

•

Press the h or g button to move the

cursor to another item in the same

group.

To move to an item in another menu

group, press the ESCAPE or h button

to return to the top of the menu group,

and repeat steps 2,3 and 4.

Remote Control

Main Unit

ESCAPE Button

AUTO

STANDBY/ON

V. POS

IRIS

ZOOM

FOCUS

PATT

SETTING

ESCAPE

PATTERN

SETTING

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

ASPECT

INPUT

Remote Control

Main Unit

MENU Button

6. To close the menu screen when

you have finished making

adjustments, press the MENU

button.

AUTO

STANDBY/ON

V. POS

IRIS

ZOOM

FOCUS

PATT

SETTING

ESCAPE

PATTERN

SETTING

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

ASPECT

INPUT

Remote Control

Main Unit

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu operations

NMenu operations 2 (with submenus)

Use the procedure below to adjust menu items that contain submenus.

Move Menu Window

Initial

1. Carry out steps 1 to 3 from “Menu

Image

Signal

Setup

Operations 1” to select the menu

item you want to set.

Color System

Auto

INPUT A Signal

Component

Auto

INPUT A Sync Type

INPUT B Signal

INPUT B Sync Type

HDMI Signal

RGB TV

Auto

The illustration at right depicts [Display

Language] in the [Initial] group selected.

Component

Off

Auto Power Off

Auto Input Search

Display Language

Lamp Running Time

Reset

Off

Memo

English

0 Hour

•

“

” appears to the right of items that

contain a submenu.

Memory 1

VIDEO

Move Menu Window

2. Press the + button to move to the

submenu.

Image

Signal

Initial

Setup

Memo

•

Some menu items contain other items

that you can select. In such cases,

move to the lower level submenu

using the + button.

Remote Control

Main Unit

English

Deutsch

Español

Français

Italiano

Display Language

Portuguêsa

Memory 1

VIDEO

Items using the

button for setting.

3. Press the h or g button to to

adjust item settings.

Display Aspect Ratio

Color System

Memo

Input A Signal

•

Press the

settings.

button to confirm some

Input A Sync Type

Input B Signal

English

Deutsch

Español

Français

Italiano

: Fix appears in the operations

guide at the bottom left of the menu

screen if this is necessary.

Input B Sync Type

HDMI Signal

Portuguêsa

Remote Control Sensor

Remote Control ID

VIDEO

4. Press the – or ESCAPE button to

return to higher level menu items.

5. To close the menu screen when

you have finished making

adjustments, press the MENU

button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu operations

NSpecial menu operations

Some items in the menu require special methods to configure.

1. Select [Color Adjustment] in the [Image] group from the main menu.

2. Press the + button to enter submenus.

3. Select a suitable item from [Standard] • [WRGB] • [WRGBYCM] using the h or g button, and

press the + button.

This explanation uses the [WRGBYCM] menu as an example.

4. Press the h, g, +, or - button to select the item you wish to configure from the color scale, and

press the

button.

Color coodinate adjustment area on the right side of the menu screen will be highlighted.

5. Press the h, g, +, or - button to adjust the setting for the item.

6. If you select R (red), G (green), B (blue),Y (yellow), C (cyan), or M (magenta) in step 4, press the

button to move to the gain adjustment area, and press the + or - button to adjust the gain.

7. Press the ESCAPE button to return to the color scale.

Example: Adjusting R (Red)

nu Window

Initial

Move Men

Setup

Image

Signal

x=0.640 y=0.330

The name of the

selected item appears

here.

Color coordinate

display area

Red

Press the

button.

0.35

0.5

Color coordinate

adjustment area

Use the h, g, +, or -

button to select an

item.

0.3

0.0

Press the ESCAPE

button.

0.6

0.82

0.65

0.5

Gain

Press the

button to

change the item to adjust.

Memory 1

VIDEO

: Edit

Gain setting

display area

Gain adjustment

area

Memo

•

See page 27 for datails about each color item.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu operations

Reset the selected parameter to the default setting.

1. Select the item you wish to reset to the default setting

from the main menu.

2. Press the RESET button on the remote control to reset

to the default settings (resetting does not affect items

with no default setting).

Memo

•

The RESET button has a special function when selecting

[WRGBYCM] in [Color Adjustment]. (ꢀ page 27)

The RESET button resets the parameters to their default

settings (corresponding to the signal input: HDTV or SDTV)

when the Color coordinate adjustment area is selected after

selecting [WRGB] or [WRGBYCM] in [Color Adjustment]. (ꢀ

page 27)

Reset all parameters to their default settings.

Move Menu Window

Initial

1. From the menu screen, select [Initial]

[All Settings].

[Reset]

Image

Signal

Setup

All Settings

Reset

All Memory

Current Memory

2. Press the + button to display a confirmation message.

Memory 4

+ : Enter

VIDEO

3. Press the

Memo

button to reset to the default settings.

Move Menu Window

Initial

Image

Signal

Setup

•

To cancel this operation and return to the previous screen,

press the ESCAPE button.

Press " " to reset

to factory settings.

Memory 4

ESC : Return

Image

VIDEO

Change the position of the menu on the screen.

Move Menu Window

Initial

1. In the menu screen, press the ESCAPE or h button

Signal

Setup

and move the cursor to one of the menu groups.

2. Press the h button to enter [Move Menu Window].

3. Use the h, g, +, or - button to move the menu screen to

a location of your choice.

4. Press the ESCAPE button to return to the previous

menu screen.

Memory 1

ESC : Return

VIDEO

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu operations

Reset the [Lamp Running Time] displayed on screen to “0”.

Move Menu Window

Initial

1. From the menu screen, select [Initial]

Running Time].

[Lamp

Image

Signal

Setup

Color System

Auto

INPUT A Signal

Component

Auto

INPUT A Sync Type

INPUT B Signal

INPUT B Sync Type

HDMI Signal

RGB TV

Auto

Component

Off

Auto Power Off

Auto Input Search

Display Language

Lamp Running Time

Reset

Off

English

12 Hours

Memory 1

+ : Enter

VIDEO

Move Menu Window

Initial

2. Press the + button to open the confirmation screen.

Image

Signal

Setup

3. Press the h or g button to select [Yes].

4. Press the

Memo

button to confirm.

Press

to reset lamp running time.

Yes

•

To cancel the operation and return to the menu screen, select

[No].

Lamp Running Time

12 Hours

Memory 4

: Fix

VIDEO

Use the [Subtitle Area] menu to adjust the size of the subtitle display area. Use [V Scroll] to adjust the vertical position of the subtitle display.

1. From the menu screen, select [Signal]

Aspect Ratio] [Special].

[Display

Move Menu Window

Initial

Image

Signal

Setup

Special

Subtitle Zoom

Cinema Zoom

Cinema Squeeze

14:9 Zoom

2. Press the + button to enter the lower level selection

menu.

3. Select [Subtitle Zoom] with h or g buttons.

4. Press the

button.

“

” appears to the right of [Subtitle zoom].

Memory 1

VIDEO

+ : Enter

Memo

•

After the first time you carry out this procedure, “ ” appears

beside [Subtitle Zoom] automatically.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu operations

5. Press the + button to enter the lower level selection

menu.

Move Menu Window

Initial

Image

Signal

Setup

Subtitle Zoom

Subtitle Area

V Scroll

6. Press h or g button to select [Subtitle Area] or [V

Scroll].

7. Press the + or – button to select a suitable setting.

Memo

•

Press the h or g button to move to a different menu item in

the [Subtitle Zoom] menu.

Memory 1

VIDEO

ESC : Return

8. Press the ESCAPE button to return to the higher level

selection menu.

Select a gamma control pattern (color tone characteristics) from the 10 preset patterns. (ꢀ page 25)

1. From the menu screen, select [Image] [Gamma].

Move Menu Window

Initial

Image

Signal

Setup

2. Press the

button to switch between capital (A to E)

Black Level

White Level

Gamma

and non capital (a to e) letters.

Hue

3. Use the + or – button to select an appropriate setting.

Saturation

100

Sharpness Type

Sharpness Gain

Color Adjustment

White Peaking

Iris

Off

WRGB

6500K 0.000uv

Level Adjustment

Memory 1

VIDEO

: Exchange

Press the

button

Move Menu Window

Initial

Image

Signal

Setup

Black Level

White Level

Gamma

Hue

Saturation

100

Sharpness Type

Sharpness Gain

Color Adjustment

White Peaking

Iris

Off

WRGB

6500K 0.000uv

Level Adjustment

Memory 1

VIDEO

: Exchange

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu operations

N Adjusting image quality using the inline menu

Use the inline menu to adjust image quality without obstructing the image during projection. See “Menu group items and functions” (page 25

to 31) for information on each setting.

Indicates that you can use the h and g buttons to

change the position of the inline menu.

Black Level

Inline menu item

Parameter adjustment area

The menu items available may differ depending on the input signal type.

For video type sources

For PC type sources

Black Level

White Level

Gamma

Hue

Saturation

Color Temp.

Sharpness Type

Sharpness Gain

White Peaking

Iris

Brightness

Contrast

Gamma

Color Temp.

White Correction

White Peaking

Iris

White Correction

Memo

•

When [Sharpness Type] is set to [Off], the [Sharpness Gain] adjustment cannot be performed.

<Example: Using the inline menu>

1. Press the

button when the menu is not open.

Image menu items appear one at a time in the lower area of the screen. If you do not carry out any operations within 5 seconds, the menu

disappears.

Black Level

Press the h or g button to select an item to set.

Sharpness Type

Off

ML MH

Press the + or - button to set the item to an appropriate setting.

Press the RESET button to return the item to its default setting.

2. To close the menu when you have finished making adjustments, press the ESCAPE button.

Memo

•

Press the

button to change between the pages of the [Gamma] menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Memory function

(Save, Recall, Lock, Copy, Reset)

The memory function automatically saves the settings of menu items listed in the “Items to be saved” table below.

N Memory configurations

The DPX-1200 stores up to six sets of configurations, called memory numbers, for each input jack. For each memory number, the DPX-

1200 stores specific configurations for each signal type, giving a total of 72 configurations.

Memory configurations for each input jack

Input Signal Type The Number of Memories

Items to be saved

Signal

Input

Image

VIDEO

S VIDEO

INPUT A

–

Black Level (Brightness)

White Level (Contrast)

Gamma

Hue

Saturation

3D Y/C Separation

Noise Reduction

Video Type

Progressive Mode

Color Space Conversion

Setup Level

–

SDTV

HDTV

RGB-PC

Color Temp.

INPUT B

SDTV

White Correction

Sharpness Type

Sharpness Gain

Color Adjustment

White Peaking

Iris

Signal Level

HDTV

RGB-PC

HDMI

SDTV

HDTV

SDTV

HDTV

Level Adjustment

Total

N Saving memory settings

All memory numbers have default settings. Since the DPX-1200 saves any changes in the menu item to the current memory number, you do

not need to save the settings each time. To preserve the specific settings, use the “Memory lock” function (ꢀ See page 43).

N Recalling a memory number

1. Press the MEMORY button (in the

STILL

LIGHT

VIDEO

DVI

MEMORY area) of which you want

to recall the settings.

VIDEO

INPUT

MEMORY

MEMORY area

Remote Control

MENU Button

1. Select the [Image] or [Signal]

group from the menu screen.

AUTO

V. POS

STANDBY/ON

ZOOM

FOCUS

PATT

IRIS

SETTING

ESCAPE

PATTERN

SETTING

ASPECT

INPUT

LAMP

COVER

TEMP

FAN

ASPECT

INPUT

Remote Control

Main Unit

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Press the g button to select

“Memory number status” from the

bottom of the screen.

Move Menu Window

Initial

Image

Signal

Setup

Black Level

White Level

Gamma Trim

Hue

Saturation

100

Remote Control

Main Unit

Sharpness Type

Sharpness Gain

Color Adjustment

White Peaking

Iris

Off

WRGB

6500K 0.000uv

Level Adjustment

+ : Enter

Memory 1

VIDEO

Memory number status

3. Press the + button to open the

submenu.

Move Menu Window

Image

Signal

Initial

Setup

Remote Control

Main Unit

Memory 1

Memory 2

Memory 3

Memory 4

Memory 5

Memory 6

VIDEO

: Fix

4. Press the h or g button to select

a memory number.

Remote Control

Main Unit

5. Press the

button to recall the

settings in the selected memory.

Memo

•

When the unit receives a signal with a different resolution from the same input jack,

it detects the new resolution and recalls an appropriate memory settings.

Remote Control

Main Unit

Download from Www.Somanuals.com. All Manuals Search And Download.

N Memory lock

The lock function protects information in a memory not to be overwritten. You can set the lock function for each memory number, and

additionally for each SDTV/HDTV/RGB-PC input.

1. Recall the memory number you

Move Menu Window

Image

Signal

Initial

Setup

wish to lock.

Black Level

White Level

Gamma Trim

Hue

2. Select a memory number status.

Saturation

100

3. Press the

button.

Sharpness Type

Sharpness Gain

Color Adjustment

White Peaking

Iris

Off

WRGB

6500K 0.000uv

“ ” appears beside locked memory

numbers.

Level Adjustment

Remote Control

Main Unit

Memory 1

VIDEO

appears

Move Menu Window

Initial

1. Select the memory number you

wish to unlock.

Image

Signal

Setup

Black Level

White Level

Gamma Trim

Hue

2. Select a memory number status.

Saturation

100

3. Press the

button.

Sharpness Type

Sharpness Gain

Color Adjustment

White Peaking

Iris

Off

WRGB

6500K 0.000uv

“ ” disappears from the memory status

screen and the memory lock is removed

from the memory number you selected.

Level Adjustment

Remote Control

Main Unit

+ : Enter

Memory 1

VIDEO

disappears

Memo

•

You can change settings when the memory is locked, but the unit does not save the changes to a memory. Any changes you make

are erased when you place this unit to standby mode. (The memory number status color changes from white to gray if you change

any menu items while the memory is locked.)

Download from Www.Somanuals.com. All Manuals Search And Download.

N Memory copy

Copy the settings stored in a memory number to another memory number.

1. Recall the memory number to be

the copy source.

2. Press the g button to select

“Memory number status” from the

bottom of the screen.

Move Menu Window

Initial

Image

Signal

Setup

Black Level

White Level

Gamma Trim

Hue

Saturation

100

Remote Control

Main Unit

Sharpness Type

Sharpness Gain

Color Adjustment

White Peaking

Iris

Off

WRGB

6500K 0.000uv

Level Adjustment

+ : Enter

Memory 1

VIDEO

Memory number status

Move Menu Window

3. Press the + button to open the

submenu.

Image

Signal

Initial

Setup

Remote Control

Main Unit

Memory 1

Memory 2

Memory 3

Memory 4

Memory 5

Memory 6

VIDEO

: Fix

4. Press the h or g button to select

a memory number to be the copy

destination.

Move Menu Window

Initial

Image

Signal

Setup

Main Unit

Remote Control

Memo

•

You cannot select a source memory

number (gray colored) as a copy

destination.

Memory 1

Memory 2

Memory 3

Memory 4

Memory 5

Memory 6

You cannot select a locked memory

number (marked “ ”) as a copy

destination.

VIDEO

: Fix

: Copy

Download from Www.Somanuals.com. All Manuals Search And Download.

Move Menu Window

Initial

5. Press the + button to display the

confirmation screen.

Image

Signal

Setup

Copy the Memory?

Press to confirm.

Main Unit

Remote Control

Yes

Memory 1

Memory 2

Memory 3

Memory 4

Memory 5

Memory 6

6. Press the h or g button to select

[Yes] .

VIDEO

: Fix

Main Unit

Remote Control

Move Menu Window

Initial

7. Press the

button.

Image

Signal

Setup

The settings stored in the source memory

number are copied to the destination

memory number.

If the copy is complete, the memory status

screen dislplays the memory number

selected in step 1.

Main Unit

Remote Control

Copying to Memory 3 ...

Memory 1

VIDEO

: Fix

Download from Www.Somanuals.com. All Manuals Search And Download.

N Resetting to the default settings

Reset parameters stored in memories to default settings.

Follow the procedure below to return parameters stored in the selected memory (corresponding to the signal input from the currently selected

input jack) to their default settings.

Move Menu Window

1. From the main menu, select

Image

Signal

Initial

Setup

[Initial]

[Reset]

[Current

Memory].

All Settings

Reset

All Memory

Current Memory

Memory 4

+ : Enter

VIDEO

Move Menu Window

2. Press the + button to display the

confirmation screen.

Image

Signal

Initial

Setup

Remote Control

Main Unit

Press "

" to reset current memory.

Memory 4

ESC : Return

VIDEO

3. Press the

parameters to their default

settings.

button to reset the

Remote Control

Main Unit

Download from Www.Somanuals.com. All Manuals Search And Download.

Reset all parameters in memories to default settings regardless of the input jack or input signal.

Move Menu Window

Initial

1. From the main menu, select

Image

Signal

Setup

[Initial]

[Reset]

[All

memory].

All Settings

All Memory

Reset

Current Memory

Memory 4

+ : Enter

VIDEO

Move Menu Window

Initial

2. Press the + button to display the

confirmation screen.

Image

Signal

Setup

Remote Control

Main Unit

Press " " to reset

all Memory.

Memory 4

ESC : Return

VIDEO

3. Press the

parameters to their default

settings.

button to reset the

Remote Control

Main Unit

Download from Www.Somanuals.com. All Manuals Search And Download.

9 Connection

Connecting to AV components

This unit is equipped with 6 types of video input jacks for AV components. Follow the diagram to connect AV components to this unit, taking

care to use cables and adapters that match the input jacks.

Input

Signal type

Composite video

Connector type

VIDEO

Pin jack

S VIDEO

INPUT A

INPUT B

D4 VIDEO

HDMI

S-Video

Mini DIN connector

BNC connector x 3-5

D-sub 15 pin

D connector

HDMI connector

Component video/RGB video

Component video

Component video/RGB video (digital)

Warning

•

Be sure to turn off the power of this unit and the source component before attempting connection.

Connection methods and jack names may differ depending on the component you are attempting to connect. Refer to the owner’s

manual for the component.

•

Insert all plugs firmly to avoid noise or other problems.

HDMI cable (digital)

D connector

cable

OUT

HDMI

RS-232C

TRIGGER OUT

REMOTE

INPUT

RGB/YP^BP

R/YCBC

D4 VIDEO

G/Y

B/PB/CB

R/PR/CR

HD/SYNC

VIDEO

D-sub

monitor

cable

BNC cable for

component connection

Video pin cable

S-Video cable

Pin/BNC

adapters

Pin cable

R/PR/CR

D1—4 output HDMI output

connectors connector

D-sub

Pin jacks

BNC jacks

S-Video output Video output

jack jack

Component/RGB video output connectors

Image output from AV components

Memo

•

Be sure to connectY/PB/PR andY/CB/CR to the jacks with the correct signals when connecting AV components to INPUT A. Refer to

the owner’s manual of the source component for more information.You may need to make connections to HD/SYNC and VD for

RGB video signals.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting to computer devices

You can use the following two methods to connect to computer devices. Be sure to use cables with jacks that match the connectors and jacks

you wish to use. You cannot use a HDMI-DVI conversion cable to connect this unit and a computer device.

Input

INPUT A

INPUT B

Signal type

RGB (Analog)

Connector type

BNC jack x 5

D-sub 15 pin

OUT

HDMI

RS-232C

TRIGGER OUT

REMOTE

INPUT

RGB/YP^B

R/YCB

D4 VIDEO

G/Y

B/PB/CB

R/PR/CR

HD/SYNC

VIDEO

BNC monitor cable

D-Sub monitor

cable

Monitor output terminal

Computer devices

Information for installers

(for US model only)

Use the supplied trigger-out DC plug to control external

components.

+ polarity (inside)

Be sure to solder the wires from an external component to the

plug terminals with the correct polarities, as illustrated at left.

- polarity (outside)

(GND)

Warning

•

Soldering the wires to terminals with incorrect polarity may

cause bodily injury or may damage this unit and the

external component connected to this unit with this cable.

- polarity

+ polarity

Download from Www.Somanuals.com. All Manuals Search And Download.

10 Installation

Setting up the DPX-1200

There are four ways of mounting the projector.

Mounting method

Projection method

A: From in front of a screen

Placed on a table

B: From behind a semi-translucent screen

C: From in front of a screen

Mounted on the

ceiling

D: From behind a semi-translucent screen

NMounting the projector on a table

A: From in front of a screen

Place the unit on a table to project and view the image from in front of the screen. Usually,

place the unit on a reasonably high table. The height from the bottom of the unit to the center

of the lens is 12.4 cm (4”-7/8).

B: From behind a screen (using a semi-translucent screen)

Place the unit on a table to project and view the image from behind a semi-translucent

screen. The distance between the projector and the screen should be the same as “A: From in

front of the screen”.

• Set the [Location] menu item in the [Setup] menu group to [Rear/Table]. (ꢀ page 22 - 40)

NMounting the projector on the ceiling

There are two kinds of brackets (sold separately: PMT-L31 and PMT-H35), which you can use to mount the projector on the ceiling. Please

consult your dealer for details on their use, and have installation done by either your dealer or a reputable contractor.

C: From in front of a screen

Mount the unit on the ceiling to project and view the image from in front of the screen. The

distance between the projector and the screen should be the same as “A: From in front of the

screen”.

•

Set the [Location] menu item in the [Setup] menu group to [Front/Ceiling]. (ꢀ page 22 - 40)

D: From behind a semi-translucent screen

Mount the unit on the ceiling to project and view the image from behind a semi-translucent

screen. The distance between the projector and the screen should be the same as “B: From

behind a screen”.

•

Set the [Location] menu item in the [Setup] menu group to [Rear/Ceiling]. (ꢀ page 22 - 40)

Download from Www.Somanuals.com. All Manuals Search And Download.

Projection distance

The most suitable distance between the screen and the projector (see Projection distance [a]) depends on the size of the screen (diagonal

length) you use. You can use the zoom function to adjust the projection distance within a preset range from Wide to Tele. You can also alter

the V.POS parameter to adjust the vertical position of the image to better suit the screen. Use the information in the table below to determine

the best location to place the projector in to suit your screen size.

Screen size

(inch)

Projection distance [a]

Wide (m) – Tele (m)

1.78 – 2.88

2.08 – 3.37

2.39 – 3.86

2.70 – 4.35

3.00 – 4.84

3.31 – 5.33

3.62 – 5.82

4.54 – 7.29

6.07 – 9.74

100

110

120

150

200

Projection distance [a]

6,07 – 9,74 m

(19'10" – 31'11")

4,54 – 7,29 m

(14'10" – 23'11")

3,00 – 4,84 m

(9'10" – 15'10")

2,39 – 3,86 m

(7'10" – 12'08")

1,78 – 2,88 m

(5'10" – 9'05")

Lens

centerline

Screen size

200''

60''

80''

100''

150''

* These are theoretical values.

During actual use there may be a deviance of a few percent.

Since the DPX-1200 has a 16:9 panel, the ideal installation location for use with a 4:3 screen depends on the size of the image you wish to

view.

Projection distance[a]

Screen size

16:9 image (*1)

Wide (m) – Tele (m)

4:3 image (*2)

Wide (m) – Tele (m)

(inch)

100

120

200

1.63 – 2.64

2.19 – 3.54

2.76 – 4.44

3.32 – 5.34

5.58 – 8.94

2.17 – 3.52

2.93 – 4.72

3.68 – 5.92

4.43 – 7.12

7.43 – 11.92

(*3)

(*1) Projects a 16:9 image that completely fills the screen (leaves a black line at the top and bottom of the screen).

(*2) Projects a 4:3 image that completely fills the screen.

(*3) When projecting both 16:9 and 4:3 images.

You can use the zoom function to make efficient use of the screen for both *1 and *2 above. The projection distance in this case is

between Wide in *2 and Tele in *1. Use the zoom to adjust the size of the projection images so that they fill the screen completely. Note

that adjustments to V.POS may cause the position of the image to change.

Download from Www.Somanuals.com. All Manuals Search And Download.

Projection image position

Follow the instructions to adjust the position of the projected image on screen.

Wide

Tele

This illustration shows the limits within which the

zoom function can alter projection distance [a] in

relation to screen size. You can adjust the image

within these limits so that it fills the screen

completely. ( ꢀ page 21)

Lens centerline

You can adjust the vertical position of the

projection image up or down by half of the height

of the screen. For example, shifting V.POS fully up

brings the lower limit of the image above the

centerline of the lens. (ꢀ page 20)

Lens centerline

(When shifted

fully up)

Lens centerline

(When shifted

fully down)

If you mount this unit on a tabletop, you can use the adjusters on its underside to change the

position of the projection image. Rotate the movable part of the two screw-type adjusters at

the front bottom of the case to adjust the height. The movement range of the adjusters is 3

cm (1-1/4 inch). Adjust with care as loosening them further than 3 cm may cause them to

separate from the unit.

NKeystone adjustment

If you mount the unit at an angle to the screen, it projects trapezoidally distorted images. You can use the [keystone Correction] item in the

[Setup] menu group to rectify this. (ꢀ page 22-34)

Memo

•

If the keystone is adjusted aspect ratio may not be correctly maintained.To correctly maintain the aspect ratio, try to use the DPX-

1200 with the lens shift in the center position.

The video may be disturbed by keystone correction. Wherever possible, we recommend setting up so the screen and projector

form a right angle.

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Reference

Glossary

The following is a list of key words used in the use of projectors and image signals and their explanations. Please refer to it when using this

manual.

For an explanation of vocabulary used in the menu, refer to "Menu group items and functions” ( ꢀ page 25).

Ceiling mount bracket

Interlace

The mounting hardware used to hang this unit from the ceiling.

Two types of bracket are available, for high and low ceilings.

Ceiling mount brackets are sold separately.

The most common type of scanning used in televisions. It divides a

screen into even and odd numbered fields for scanning, and then

builds an image by combining them into one image (frame).

Cinemascope size

Keystone Correction

The widest film format in 70 mm film, with an aspect of 2.35:1.

Using the unit at an angle to the screen distorts the projected image

trapezoidally. You can use Keystone Correction to electronically

correct this distortion.

Color spacing

The conversion of YUV color separated signal to RGB signal.

There are two formats for this, BT.601 for SDTV, and BT.709 for

HDTV. This unit switches between them as required.

Letterbox

A method of converting the content of landscape oriented film to a

4:3 signal. You can watch landscape images without trimming them

by adding a black bar to the top and bottom of the screen, however

this sacrifices vertical resolution to some extent.

Component video signal

A method of sending video signals with independent luminance

and color signals. Component video gives a higher image quality

than ordinary composite video because it bypasses mixing and

separating circuits. Component video signal consists of three lines,

the luminance signal (Y), and two color difference signals (P^B/CB,

PR/CR).

Progressive

A method of displaying all scanning lines in a frame at once,

reducing flicker noticeable on a larger screen and creating a sharp,

smooth image. This unit uses progressive scanning for progression.

Composite video signal

RGB Signal

The most common type of video signal, combining luminance and

color signals in one line. This method requires mixing and

separating processes on both the send and receive sides. Use a pin

cable for connection.

A method of transmitting color information using a numeric

representation of the primary colors red, green, and blue separately.

When received, it is expressed in various colors by adding a mixing

colors. RGB is widely used for sending and receiving color images

between computers, and requires horizontal and vertical sync

signals.

DCDi^TMfunction

Directional Correlational Deinterlacing, a high quality image

circuitry developed by the Faroudja company. DCDi^TMuses edge

cutting techniques to remove jagged edges from images during

Interlace to Progressive conversion, allowing smooth, natural

reproduction of images.

SDTV

Standard Definition Television, a term used to define normal

television broadcasts which do not meet HDTV standards.

Smart zoom

DLP^TMtechnology

Digital Light Processing, an image display engine used in

projectors that use the DMD™ chip developed by Texas

Instruments.

Expands the left and right sides of a 4:3 image without altering the

center, when you are attempting to project a 4:3 image on a wide

screen format. This creates some distortion at both edges.

Squeeze

D terminal

A method of compressing film images horizontally to an aspect of

ratio of 4:3 when recording to video medium. The raw image is

oblong, so needs to be passed through a desqueezing circuit to be

projected in it’s original form.

A cable that allows transmission of all of the signals in composite

video in one cable. This method is used for transmitting image

signals between the latest AV components. There are 5 methods of

transmission, D1-D5. This unit is compatible with D4.

Standby

HDCP

The state in which the circuit that receives infrared-signals from the

remote control is active, but all other main circuits are turned on.

The unit consumes a small amount of power in this state.

A technique designed to protect the video transmission between a

DVI or HDMI transmitter and a display device.

HDMI^TM

S Video signal

High-Definition Multimedia Interface, a method of differentially

transmitting digital RGB/component video signal from computers

and home digital equipment.

S stands for Separate. A method of sending signals with separate

luminance (Y) and color (C) signals. Use a 4-pin mini DIN

connector and cable for connection.

HDTV

Sync.

High-Definition Television, a term used to define systems that

satisfy the following conditions:

Computers output signals with a given regular frequency, which

you must synchronize the projector to in order to produce a good

quality image. If you do not match the phase of the signal, the

image may be flickery, faded, or distorted.

• A vertical resolution of 720p or 1080i (p stands for progressive

scans, ; stands for interlace scans)

• A 16:9 aspect ratio

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary

Test pattern

This unit contains test patterns which you can use to adjust the

position and focus of the projected image on the screen.

Tracking

Computers output signals with a given regular frequency, which

you must synchronize the projector to in order to produce a good

quality image. If you do not match the phase of the signal, vertical

stripes may appear on the image.

Vista size

A standard film size, with an aspect ratio of 1.85:1 in North

America, and 1.66:1 in Europe.

3-2 pulldown detection style IP conversion

A function for directly converting interlace signal into sixty frame

progressive signal used when receiving 60 field interlace signal

from an image source recorded with the same 24 frames as movie

film. This allows DVD and other materiel recorded with 24 frames

to be projected on large screens as a natural, precise image with no

loss of quality, comparable to a movie film.

* DLP^TM, DMD^TM, DarkChip2^TM, and DarkChip3^TMare registered

trademarks of the Texas Instruments corporation of America.

* “DCDi” is a trademark of Faroudja, a division of Genesis

Microchip, Inc.

* HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademark of HDMI

Licensing LLC.

Download from Www.Somanuals.com. All Manuals Search And Download.

Compatible signal types

The following tables show the types and formats of signals the DPX-1200 can project. Signals other than those listed here may not be

projected correctly.

NTV format 1

(Composite or S Video signals received at the VIDEO or S-VIDEO jack)

V active

(lines)

f (V)

(Hz)

fsc

(MHz)

Signal type

Color system

NTSC

PAL

SECAM

PAL

NTSC

PAL

NTSC

PAL

480

576

480

576

480

576

59.94

50.00

59.94

50.00

3.58

4.43

4.406, 4.25

4.43

3.58

SECAM

PAL60

NTSC4.43

PAL-M

PAL-N

3.58

NTV Format 2

(Component/RGB TV signals received at the INPUT A and B, or component signals received at the D4 jack)

H active

(pixels)

V active

(lines)

f (H)

(kHz)

f (V)

(Hz)

Signal type

480i

576i

480p

576p

720p/50Hz

720p/60Hz

1035i

1080i/50Hz

1080i/60Hz

720

1280

1920

483

576

480

576

720

1035

1080

15.734

15.625

31.469

31.250

37.500

44.955

33.750

28.125

33.716

59.940

50.000

59.940

50.000

59.940

60.000

50.000

59.940

NPC Format

(Analog RGB PC signals received at the INPUT A or B jack)

H active

(pixels)

V active

(lines)

f (H)

(kHz)

f (V)

(Hz)

Signal type

VESA (*1)

VGA/60Hz

640

800

1024

640

480

600

768

480

31.469

37.861

37.500

43.269

35.156

37.879

48.077

46.875

53.674

48.363

35.000

59.940

VGA/72Hz

VGA/75Hz

VGA/85Hz

SVGA/56Hz

SVGA/60Hz

SVGA/72Hz

SVGA/75Hz

SVGA/85Hz

XGA/60Hz

72.809

75.000

85.008

56.250

60.317

72.188

75.000

85.061

60.004

66.666

Macintosh (*2)

(*1) VESA is a registered trademark of the Video Electronics Standards Association.

(*2) Macintosh is a registered trademark of the Apple Computer corporation.

NHDMI Format

(Component/RGB signals input from the HDMI jack)

H active

(pixels)

V active

(lines)

f (H)

(kHz)

f (V)

(Hz)

Signal type

Component type

VGA

480i

576i

640

(1440) 720

480

576

31.469

15.734

15.625

59.94

RGB (*3)

RGB/YCBCR4:4:4/YCBCR4:2:2 (*4)

720

480p

576p

480

576

31.469

31.25

59.94

RGB/YCBCR4:4:4/YCBCR4:2:2 (*4)

1440

720

1440

720/60p

720/50p

1080/60i

1080/50i

1280

1920

720

1080

59.94

RGB/YCBCR4:4:4/YCBCR4:2:2 (*4)

44.955

33.716

28.125

(*3) VGA mode is only available for RGB signals.

(*4) You cannot select YCBCR4:2:2 mode manually. This mode only available when you set the unit to HDMI Auto mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

N Regular care

Be sure to disconnect the power cable before doing any maintenance.

Wipe with a soft cloth. Use a damp cloth with a mild detergent and then wipe with a dry cloth again if the unit is heavily soiled. Do not use

strong solvents such as thinner or alcohol as they may damage the unit casing.

<Lens>

Use commercially available blowers or lens tissue to remove any dirt from the lens.

If dust accumulates on the ventilation port filter, the internal temperature of the unit rises, which may cause damage to the unit. Clean the

filter approximately once every 200 hours. Remove the power cable from the AC outlet, and remove dust from the filter with a vacuum

cleaner.

To prevent dust from entering the filter itself, be sure to vacuum the filter with the unit on its side.

N Replacing the filter

Replace the filter when it becomes difficult to remove dust from it.

1. Turn off the power and remove the power cable.

2. Carefully place the unit upside down on a soft cloth to prevent scratching.

3. Press the filter hook on the underside of the main unit to remove the filter.

4. Firmly attach the new filter.The lamp does not light if the filter is

incorrectly attached.

Warning

•

Contact aYAMAHA dealer or service center if you require replacement filters.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

N Replacing the lamp

The lamp used as a light source in the DPX-1200 is a consumable item which will gradually lose its brightness during the course of use. It is

advisable to replace the lamp when running time has exceeded 2000 hours.

You can check the lamp running time in the [Lamp Running Time] in the [Initial] menu group of the Menu screen. The LAMP warning

indicator will blink when running time exceeds 2000 hours.

There will also be a message displayed on the screen. In this case, follow the instructions below to replace the lamp cartridge. For details on

replacement of lamp cartridges, consult the store where you purchased the DPX-1200.

Warning

•

Be sure to use the replacement lamp cartridge PJL-427. Other lamp cartridges are not suitable for use in the DPX-1200.

If replacing the lamp of the projector that has been installed to the ceiling, you should remove the projector from the ceiling before

replacing the lamp.

•

Before starting to replace the lamp cartridge, turn off the power, disconnect the power cable after the fan has completely stopped,

and wait at least one hour for the lamp to cool down.

•

Do not remove any other screws than those specified in the following steps.

The gases inside the lamp contain mercury vapor. Be careful the lamp may break if it gets old or overtasked.The life of a lamp

differs depending on operation environments.

1. Loosen the lamp cover screws.

Lamp cover screws

2. Remove the lamp cover.

3. Loosen the screws of the lamp cartridge.

4. Grip the handle and pull the lamp cartridge to remove it.

5. Insert the new lamp cartridge by reversing the above steps, and tighten

the screws to fix it into place.

6. Replace the lamp cover and secure it with the screws.

The lamp will not turn on if the cover is not securely fastened.Take care to

attach it firmly in place.

7. Connect the unit to the power outlet, turn the unit on, and reset [Lamp

Running Time] on the [Initial] group in the menu. (ꢀ page 38)

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Problem

Cause

Remedy

The DPX-1200 does not The power cable is not plugged in.

Plug the power cable in firmly.

turn on.

You attempted to turn on The DPX-1200

Wait for approximately two minutes.

immediately after turning it off.

<MEMO>

•

To protect the lamp, you cannot turn on

power for two minutes after you turn it off.

The filter cover is not correctly attached.

The lamp cover is not correctly attached.

Correctly attach the filter cover.

Correctly attach the lamp cover.

No picture.

The lens cover has not been removed.

Remove the lens cover.

Check the connections.

The DPX-1200 is not correctly connected

to the other components.

The input signal has not been correctly

selected.

Select the correct input signal with the

INPUT button.

Press the AUTO button on the remote

control.

Use the menu to adjust the signal setting

to suit the input setting.

[Initial]

The picture is turned off.

Press the HIDE button again to cancel the

HIDE function.

The computer is not set to display on the

external monitor.

Set the computer to display on the external

monitor. (Refer to the computer operating

instructions.)

Image is unstable.

Picture is blurred.

The connection cables are not correctly

attached to the connectors.

Correctly connect the cables to the

appropriate connectors.

The lens is not correctly focused.

Press the FOCUS button, and adjust the

focus.

The screen and the DPX-1200 are not

facing each other directly.

Adjust the projection angle and direction,

and the height of the DPX-1200.

The image becomes

cloudy.

There is condensation on the DPX-1200.

Switch the DPX-1200 power off until the

condensation disappears.

Cannot adjust focus or [Lens Adjustment Lock] in the menu is set

Set correctly.

Set [Lens Adjustment Lock] to off.

Press the MENU button to display the menu

zoom, or the vertical

position of the lens.

to ON.

and select [Setup]

Lock].

[Lens Adjustment

Remote control does

not work correctly.

The batteries are exhausted.

Replace both batteries with new ones.

The remote control sensor is not set

correctly.

Set correctly.

Press the MENU button to display the menu

and select [Setup]

Sensor].

[Remote Control

There is a fluorescent lamp near the

remote control sensor being used.

Turn off the remote control sensor near the

fluorecent lamp, and use the other remote

sensor.

The remote control code switch is

incorrectly set.

Set the remote control code switch to the

same ID number as the setting on the

“REMOTE CONTROL ID” in the setting menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Problem

Cause

Remedy

COVER warning

indicator lights up.

The filter cover is not correctly attached.

The lamp cover is not correctly attached.

Tightly attach the filter cover.

Tightly attach the lamp cover.

LAMP warning

indicator lights up or

blinks.

Lamp running time has exceeded 2000

hours.

Replace the lamp with a new one.

The lamp has burned out.

TEMP warning indicator The temperature inside the DPX-1200 is

lights up. extremely high.

Check that the ventilation slots are not

covered.

FAN warning indicator The fan is broken.

lights up.

Contact the store where the DPX-1200 was

purchased.

•

This unit uses a DMD^TMchip for the picture display.Their highly accurate technology makes it possible to keep more than 99.99% of

effective pixels, however, unexpectedly it can produce less than 0.01% of ineffective pixels. In such a case, missing or flashing of a

few pixels can be found on the screen.These are characteristics of DMD^TM, not mechanical problems.

Download from Www.Somanuals.com. All Manuals Search And Download.

Message display

Message

Condition

No Signal

The unit is not receiving or detecting any signal at the selected input jack. This message is

displayed together with the name of the input source selected with the INPUT button.

INPUT A (Component) (Example)

The input name selected by the INPUT button is displayed. It will turn off 2 seconds after

the signal has been input.

Out Of Range

The unit is not able to decode the PC or HDMI signal currently being input.

The unit is not able to decode the video signal currently being input.

Unknown Format

Auto Sync...

The unit is setting itself to the most appropriate configuration for the RGB signal currently

being received.

Memory 1—6 Now Processing

The memory setting number is displayed for two seconds.

The lamps has reached its recommended

This message is displayed when the power switch is turned on if the lamp running time

replacement time. Please replace with a new exceeds 2000 hours. Press the ESCAPE button to remove the message.

one.

Press again to enter standby.

Lens Adjustment is locked.

Press the STANDBY/ON button once more to place the unit in standby mode.

This message will display for two seconds if you press the V. POS, ZOOM, or FOCUS

button when [Lens Adjustment Lock] is set to [On].

Invalid Operation

Appears in the menu operation guide when you press an invalid button during menu

operation. This message displays for two seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

LED indicator meanings

LED indicator

State

Meaning

Unlit

Electrical fault.

Standby

STANDBY/ON (*)

Lit orange

Blinking green

Lit green

Preparing for operation.

Operating

Blinking orange

Cooling the lamp.

Blinking red / blinking Blinking red: Error in the LAMP/COVER/TEMP system

red and orange rapidly Blinking red and orange rapidly: Error in the FAN system

Unlit

Normal

LAMP

Blinking orange

Lit red

Unlit

The lamp running time has exceeded 2000 hours.

The lamp has burned out.

Normal

COVER

TEMP

FAN

Lit red

Unlit

The lamp cover or the filter cover is not attached correctly.

Normal

Lit red

Unlit

The temperature of the lamp or the interior of the case is abnormally high.

Normal

Lit red

The cooling fan has broken.

(*) This LED is also present on the front panel of the main unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

• Optical

Projection mode

Lens

DLP^TM(DMD^TM) type, 1280 X 720 pixels, 0.8 inch

f=24.3 – 38.9 mm F=2.7 – 5.0, Electronic zoom(x 1.6), Electronic focus, Electronic lens shift

270 W SHP lamp

Lamp

Screen size

Brightness

Contrast

60–200 inch (16:9)

800 – 400 ANSI lm (depends on Iris Setting)

2500:1 to 5000:1 (depends on Iris Setting)

• Input

Color system

VIDEO

NTSC, PAL, SECAM, NTSC4.43, PAL-M, PAL-N, PAL60

Composite signal

S-Video signal

1Vp-p/75 Ω, Negative sync

S VIDEO

Y:1Vp-p/75 Ω, Negative sync

C:0.286 or 0.3Vp-p/75 Ω

D4 VIDEO

Component signal

Y with sync:1Vp-p/75 Ω, Negative sync

(480i, 576i, 480p, 576p)

Y with sync:1Vp-p/75 Ω, 3 values sync

(1035i, 1080i, 720p)

PB/CB, PR/CR:0.7Vp-p/75 Ω

INPUT A/INPUT B

Component signal

RGB signal

Y with sync:1Vp-p/75 W, Negative sync (480i, 576i, 480p, 576p)

Y with sync:1Vp-p/75 W, 3 values sync (1035i, 1080i, 720p)

PB/CB, PR/CR:0.7Vp-p/75 Ω

G with sync:1Vp-p/75 Ω, Negative sync

(480i, 576i, 480p, 576p)

G with sync:1Vp-p/75 Ω, 3 values sync

(1035i, 1080i, 720p)

G:0.7Vp-p/75 Ω

(When using HD/VD or SYNC)

B, R:0.7Vp-p/75 Ω

HD, VD:1–5Vp-p/2.2kΩ, positive and negative sync

SYNC:2Vp-p/2.2kΩ, Negative sync (with video signals) (480i, 576i)

SYNC:0.6–5Vp-p/2.2kΩ, Negative sync (without video signals)

(480i, 576i, 480p, 576p)

HDMI

Digital RGB/component signal

RS-232C (D-sub 9 pins)

• Controls

Remote

Trigger

+12 V/Max 200 mA when the power is on

1 in front, 1 at rear

Wireless remote

Wired remote

1 input jack, 1 output jack

• General

Usable temperature range

5 °C – 35 °C

Usable humidity range

Power supply

30 % – 85 %(There should be no condensation)

AC100 – 120 V/220 – 240 V, 50/60 Hz

375 W

Power consumption

Power consumption in standby mode 0.1 W – 0.2 W

Noise level

Dimension

Weight

30 dB(Standard mode), 28 dB(When Lamp Power Mode is set to 80)

495(W) x 192.6(H) x 465.4(D) mm

13.8 kg

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensional drawing

119.1

4"-3/5

465.4

18"-5/16

124.6

4"-7/8

132.1

297.4

5"-3/16

11"-3/4

Specifications are subject to change without notice.

•

This unit may interfere with reception if placed in close proximity to a radio or television receiver. Follow the instructions in this

manual to install the unit correctly.

Download from Www.Somanuals.com. All Manuals Search And Download.

C2004

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Japan WE49620

Download from Www.Somanuals.com. All Manuals Search And Download.

Westinghouse Flat Panel Television LTV 19w6 User Manual
Wharfedale Microphone DM40 User Manual
Whirlpool Double Oven GGG390LX User Manual
Woodstock Trimmer M1044 User Manual
Xerox Copier 3435 User Manual
Xilinx Computer Hardware Spartan 3E 1600E User Manual
Yamaha Electronic Keyboard GT1 User Manual
Yamaha Outboard Motor 6D6 28199 10 User Manual
Zanussi Dishwasher ZDI 6896 SX User Manual
Zebra Technologies Printer GX420D User Manual