Cubase SX3 / DM2000 V2 Setup and Operation
Page 1
Cubase SX3 / DM2000 V2 Setup and Operation
This document describes setup and operation for remote control of Cubase SX from the
DM2000 digital mixing console. These instructions apply to DM2000 V2.0 or higher
and Cubase SX V3.0.0 or higher.
Driver Installation
1)
Connect your PC or Macintosh computer
The DM2000 should be connected to your computer by connecting the TO HOST
USB port on the DM2000 to a USB port on your computer.
2)
Install Driver
Once your computer is connected, you will need to install the USB-MIDI driver
included on the DM2000 CD-ROM. It is recommended that you install the latest
Configuring DM2000 V2
1)
2)
Press the [SETUP] display access key and select the MIDI/TO HOST screen.
Set the DAW port assignment to USB 2-5 (this allows USB port 1 to be used for
the DM2000 Studio Manager Editor software). Note: you must use USB ports 2-
5 for DAW Control and USB port 1 for Studio Manager if you intend to use these
two applications simultaneously.
3)
4)
5)
Press the [REMOTE] display access key and assign CUBASE SX as the Target
for one of the Remote layers.
(See “About Remote Layers” in the DM2000 manual for more information.)
Press the [LOCATOR] display access key and select DAW Control as the
function for the transport and locate keys. This allows the Cubase SX transport to
be controlled regardless of whether a Remote or Internal mixing layer is active.
Press the relevant [REMOTE] LAYER button to select the Cubase SX Remote
Control Layer.
When the Cubase SX Remote Control Layer is selected, the DM2000’s control
surface controls Cubase SX rather than the internal mixing of the DM2000. In
order to control the DM2000, you need to select an Input Channel Layer or the
Master Layer. Audio mixing on the Input and Master Layers, and Automix
continues while the Cubase SX Layer is selected.
Download from Www.Somanuals.com. All Manuals Search And Download.
Cubase SX3 / DM2000 V2 Setup and Operation
Page 3
level shown in the fluorescent display section. In this mode, each send can be switched
On/Off by pressing the encoder.
Selected Channel Functions
Pressing any of the DISPLAY switches in the SELECTED CHANNEL section of
DM2000 will cause the VST Audio Channel Settings window to open in Cubase SX.
COPY & PASTE
The CHANNEL COPY and PASTE switches on DM2000 perform the same functions as
COPY and PASTE in Cubase SX’s Edit menu.
EQ
The four bands of EQ GAIN, FREQUENCY and Q on DM2000 control the same
functions on the selected Cubase SX channel, and the parameter value is displayed on the
console. To switch an EQ band On or Off, hold down the FREQUENCY/Q encoder for
one second.
The entire EQ section can be bypassed by pressing the EQ ON key in the SELECTED
CHANNEL section of DM2000. (Note: when the EQ ON LED is lit in the DM2000, this
indicates EQ Bypass in Cubase SX.)
PANNING
The PAN encoder and the JOYSTICK on DM2000 control the pan functions of Cubase
SX. Even if there is no surround panning enabled, the joystick can be used for Left-Right
panning.
AUX SENDS
The AUX SEND LEVEL encoders and ON switches edit the 8 sends in Cubase SX. So
only the first two BANKS on DM2000 are used. By pressing the LEVEL encoders, the
send can be switched between Pre and Post Fader.
PHASE AND INSERT
The PHASE switch on DM2000 switches the phase of the selected Cubase SX channel,
and the INSERT ON switch bypasses all Inserts for the selected channel.
Download from Www.Somanuals.com. All Manuals Search And Download.
Cubase SX3 / DM2000 V2 Setup and Operation
Page 4
FX Sends, Routing and Insert Editing
FX SENDS
In the EFFECTS / PLUG-INS section of the DM2000, press the INTERNAL EFFECTS
key to access FX Send information on the LCD screen. The encoders below the screen
can edit various functions:
• Encoder 1 edits the send level.
• Encoder 2 edits the send On/Off status (by turning the encoder).
• Encoder 3 edits between Pre and Post Fader (by turning the encoder).
• Pressing any of the encoders will switch all sends On/Off.
There are 8 sends spread over 8 pages. To access different sends, use the UP and DOWN
cursor buttons to the left of the LCD encoders.
ROUTING
Press the PLUG-INS switch to access Routing information in the LCD. There are two
pages, accessed by pressing the UP and DOWN cursor buttons to the left of the LCD
encoders. The following functions can be edited:
Page 1
• Encoder 1 chooses the Output Bus for the selected channel
• Encoder 2 switches the Monitor On/Off (by pressing or turning the encoder)
• Encoder 3 selects the Input bus
• Encoder 4 edits the Input Gain (the encoder must be pressed down while turning)
Page 2
Only Encoder 1 has a function. It is used to switch the Input Phase On/Off (by pressing
or turning the encoder).
INSERTS
When the CHANNEL INSERTS switch is pressed on DM2000, the LCD shows Insert
information for the selected channel.
• Encoder 1 selects which insert is to be edited
• Encoder 2 switches the insert On/Off (by turning, not pressing)
• Encoder 3 selects the type of effect to insert
Once an Effect has been selected, all the parameters can be edited by changing the page
viewed on the LCD (by pressing the UP and DOWN cursor buttons to the left of the LCD
encoders). The number of pages available depends on the number of parameters used by
the Effect.
Note: in any of the above modes, the EFFECT DISPLAY switch toggles between
showing the parameter names and the parameter values on the LCD.
Download from Www.Somanuals.com. All Manuals Search And Download.
Cubase SX3 / DM2000 V2 Setup and Operation
Transport & Automation
Page 5
Ensure that DAW CONTROL is selected in the LOCATE MEMORY screen of the
LOCATOR display menu on DM2000.
TRANSPORT CONTROLS
The following Transport functions can be controlled from DM2000:
• REC
• PLAY
• STOP
• FF
• REW
• SCRUB
• SHUTTLE
• LOOP
• QUICK PUNCH
• ONLINE
LOCATE FUNCTIONS
The following DM2000 locate functions also control the corresponding Cubase SX
functions:
• RTZ
• END
• IN
• OUT
• SET
• LOCATE 1-8
To set a locate point (Marker in Cubase SX), hold the SET switch on DM2000, and press
the required LOCATE MEMORY switch at the required time. Note: DM2000 must be in
the appropriate Cubase SX Remote Layer in order to set Markers.
TRACK-ARMING
The DM2000 TRACK ARMING 1-24 switches control the RECORD ENABLE switches
of the corresponding Cubase SX channels.
AUTOMATION
The following AUTOMIX switches on DM2000 control automation functions of Cubase
SX:
• ENABLE puts all Cubase SX channels into READ mode
• REC puts all Cubase SX channels into WRITE mode.
• The AUTO switch above each DM2000 channel fader switches READ On/Off for
each channel individually. However, when AUTO-REC is switched on, the channel
AUTO switches function to control WRITE On/Off in Cubase SX.
Download from Www.Somanuals.com. All Manuals Search And Download.
Cubase SX3 / DM2000 V2 Setup and Operation
User Defined Keys
Page 6
When DM2000 is used to remotely control Cubase SX, the following User Defined Keys
have permanently assigned functions:
UDEF 1: Brings the Project window to the front
UDEF 2: Scrolls channels down in banks of 8
UDEF 3: Scrolls channels up in banks of 8
UDEF 9: Open or closes the VST Mixer window
UDEF 10: Scrolls channels down one channel at a time
UDEF 11: Scrolls channels up one channel at a time
Other User Defined Keys (UDEF 4-8 and 12-16) can be programmed by the user to
control various Cubase SX functions. These functions can be selected in the DEVICE
SETUP of Cubase SX, by selecting “YAMAHA DM2000 V2” and choosing the desired
‘Category’ and ‘Command’ from the drop-down list for each button.
Other Functions
ZOOM & NAVIGATION
The DM2000 CURSOR keys (next to the Scrub Wheel) have two different functions.
Their mode can be changed by pressing the INC key above the cursor keys. The mode is
shown on the LCD display.
• ZOOM mode: the cursor keys control the vertical and horizontal zoom of the Project
Window.
• NAVIGATION mode: the cursor keys control the selection of channels and objects in
the Project Window.
TIME COUNTER
The TIME COUNTER is displayed on the DM2000 LCD screen, with the counter mode
(TIME CODE / FEET / BEATS). If “Samples” is selected in Cubase SX, then no
selection is displayed in the DM2000 LCD.
METER BRIDGE
The DM2000 meter bridge displays Cubase SX’s input channel levels when the correct
REMOTE layer is selected. The TIME CODE counter is also displayed on the Meter
Bridge.
Download from Www.Somanuals.com. All Manuals Search And Download.
|