FAX Option Type C3000
Operating Instructions
Facsimile Reference
Transmission
1
2
3
4
5
6
7
Other Transmission Features
Reception
Changing/Confirming Communication Information
Storing a Document
Fax via Computer
Appendix
Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the
Safety Information in "About This Machine" before using the machine.
Download from Www.Somanuals.com. All Manuals Search And Download.
Manuals for This Machine
Refer to the manuals that are relevant to what you want to do with the machine.
❖ About This Machine
Be sure to read the Safety Information in this manual before using the ma-
chine.
This manual provides an introduction to the functions of the machine. It also
explains the control panel, preparation procedures for using the machine,
how to enter text, and how to install the CD-ROMs provided.
❖ General Settings Guide
Explains User Tools settings, and Address Book procedures such as register-
ing fax numbers, e-mail addresses, and user codes. Also refer to this manual
for explanations on how to connect the machine.
❖ Troubleshooting
Provides a guide to solving common problems, and explains how to replace
paper, toner, staples, and other consumables.
❖ Security Reference
This manual is for administrators of the machine. It explains security func-
tions that the administrators can use to protect data from being tampered, or
prevent the machine from unauthorized use.
Also refer to this manual for the procedures for registering administrators, as
well as setting user and administrator authentication.
❖ Copy/Document Server Reference
Explains Copier and Document Server functions and operations. Also refer to
this manual for explanations on how to place originals.
❖ Facsimile Reference
Explains Facsimile functions and operations.
❖ Printer Reference
Explains Printer functions and operations.
❖ Scanner Reference
Explains Scanner functions and operations.
❖ Network Guide
Explains how to configure and operate the machine in a network environ-
ment, and use the software provided.
This manual covers all models, and includes descriptions of functions and
settings that might not be available on this machine. Images, illustrations, and
information about operating systems that are supported might also differ
slightly from those of this machine.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
❖ Other manuals
• PostScript3 Supplement
• UNIX Supplement
• Manuals for DeskTopBinder Lite
• DeskTopBinder Lite Setup Guide
• DeskTopBinder Introduction Guide
• Auto Document Link Guide
Note
❒ Manuals provided are specific to machine types.
❒ Adobe Acrobat Reader/Adobe Reader must be installed in order to view the
manuals as PDF files.
❒ For “UNIX Supplement”, please visit our Web site or consult an authorized
dealer.
❒ “PostScript3 Supplement” and “UNIX Supplement” include descriptions of
functions and settings that might not be available on this machine.
❒ The following software products are referred to using general names:
Product name
General name
DeskTopBinder Lite *1 and DeskTopBinder Profes-
sional
DeskTopBinder
ScanRouter EX Professional *1 and ScanRouter EX En-
terprise *1
the ScanRouter delivery software
*1
Optional
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Manuals for This Machine......................................................................................i
NOTICE ...................................................................................................................1
Important Safety Instructions...............................................................................3
Caution.......................................................................................................................3
How to Read This Manual .....................................................................................4
Symbols .....................................................................................................................4
Names of Major Functions .........................................................................................4
Reading the Display...............................................................................................5
Reading the Display Panel and Using Keys...............................................................6
Simplified Display.......................................................................................................8
Function List ..........................................................................................................9
1. Transmission
Transmission Modes ...........................................................................................13
Selecting Type of Transmission...............................................................................14
Memory Transmission..............................................................................................15
Parallel Memory Transmission ..............................................................................19
Automatic Redial ...................................................................................................20
Dual Access...........................................................................................................20
Simultaneous Broadcast........................................................................................20
Immediate Transmission..........................................................................................21
Displaying Confirmation of Transmission.................................................................24
IP-Fax Functions..................................................................................................25
Terminology .............................................................................................................27
Notes on Using IP-Fax.............................................................................................28
Functions Not Available for IP-Fax Transmission ....................................................28
Internet Fax Functions ........................................................................................29
Notes on Using Internet Fax ....................................................................................30
Functions Not Available by E-mail Transmission.....................................................31
Functions Not Available by E-mail Reception ..........................................................32
E-mail Subject..........................................................................................................32
T.37 Full Mode .........................................................................................................33
Placing Originals..................................................................................................34
Setting the Original Orientation................................................................................36
Scanning Two-Sided Originals.................................................................................37
Acceptable Original Sizes ........................................................................................40
Paper Size and Scanned Area.................................................................................41
Original Sizes Difficult to Detect...............................................................................43
Transmission with Image Rotation...........................................................................44
Stamp.......................................................................................................................45
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Settings .......................................................................................................47
Scan Type................................................................................................................47
JBIG Transmission ................................................................................................49
Resolution ................................................................................................................49
Scan Size.................................................................................................................51
Auto Detect............................................................................................................52
Regular..................................................................................................................53
Area.......................................................................................................................54
Mixed Original Sizes..............................................................................................56
Density (Contrast) ....................................................................................................58
Mixing Scan Settings for a Multiple Page Original ...................................................60
Changing the Line Port .......................................................................................61
Simultaneous Broadcast Using Multiple Line Ports .................................................63
Specifying a Destination .....................................................................................64
Sending Over a Fax Line .........................................................................................64
Entering a pause ...................................................................................................65
Entering a tone ......................................................................................................66
Sending by IP-Fax....................................................................................................67
Regarding IP-Fax destinations ..............................................................................69
Sending to an E-mail Address..................................................................................70
Bypassing the SMTP server..................................................................................73
Using the Address Book to Specify Destinations.....................................................76
Switching the titles in the Address Book................................................................77
Specifying Group Destinations.................................................................................78
Selecting Destinations from Recent Destinations ....................................................79
Search by Destination Name ...................................................................................85
Search by Fax Number/IP-Fax Destination..............................................................87
Search by E-mail Address........................................................................................90
Search Using Advanced Search ..............................................................................92
Search by Registration Number...............................................................................95
On Hook Dial ........................................................................................................97
Manual Dial...........................................................................................................99
Sender Settings..................................................................................................101
PIN Code Transmission .........................................................................................104
Advanced Features............................................................................................106
Setting SUB Codes for Transmission.....................................................................106
Setting a password..............................................................................................109
Setting SEP Codes for Reception..........................................................................109
Entering a password............................................................................................112
SEP Code RX Reserve Report ..............................................................................112
SEP Code RX Result Report .................................................................................113
Canceling a Transmission ................................................................................114
Before the Original Is Scanned ..............................................................................114
While the Original Is Being Scanned......................................................................114
While the Original Is Being Transmitted.................................................................115
Before the Transmission Is Started........................................................................117
Confirming a Transmission ..............................................................................120
Checking the Storage Result (Memory Storage Report)................................122
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending at a Specific Time (Send Later) .........................................................123
Requesting a Reception Notice........................................................................125
Setting an E-mail Destination as a BCC ..........................................................127
Entering the Subject..........................................................................................130
Entering the Text................................................................................................133
Transmission Options.......................................................................................135
Standard Message Stamp......................................................................................135
Auto Reduce ..........................................................................................................136
Label Insertion........................................................................................................138
Closed Network......................................................................................................140
SUB Code Transmission........................................................................................141
SEP Code Reception .............................................................................................142
Fax Header Print....................................................................................................144
3. Reception
Types of Reception............................................................................................147
Immediate Reception .............................................................................................147
Memory Reception.................................................................................................148
Substitute Reception..............................................................................................149
Receiving documents unconditionally .................................................................150
Reception Modes ...............................................................................................152
Manual Reception ..................................................................................................152
Auto Reception.......................................................................................................152
Switching the Reception Mode...............................................................................153
Receiving Internet Fax Documents..................................................................154
Auto E-mail Reception ...........................................................................................154
Manual E-mail Reception.......................................................................................155
Received Images ...................................................................................................155
Reception Functions .........................................................................................157
Routing Received Documents................................................................................157
Routing received documents with SUB Code......................................................157
Transferring Received Documents.........................................................................158
SUB Code Transfer Report .................................................................................158
Forwarding Received Documents..........................................................................159
SMTP Reception Using Internet Fax......................................................................160
Routing e-mail received via SMTP ......................................................................161
JBIG Reception......................................................................................................162
Auto Fax Reception Power-Up...............................................................................162
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Options.................................................................................................163
Print Completion Beep ...........................................................................................163
Checkered Mark.....................................................................................................163
Center Mark ...........................................................................................................164
Reception Time......................................................................................................164
Two-Sided Printing.................................................................................................165
180-degree rotation printing ................................................................................166
Multi-Copy Reception.............................................................................................166
Image Rotation.......................................................................................................167
Page Separation and Length Reduction ................................................................168
Page Reduction......................................................................................................169
TSI Print (Transmitting Subscriber Identification Print) ..........................................169
If There Is No Paper of the Correct Size................................................................170
Setting priority trays.............................................................................................170
Just size printing..................................................................................................171
Where Incoming Documents Are Delivered - Output Tray.....................................172
Specifying tray for lines .......................................................................................172
Tray Shift .............................................................................................................173
Adding a Destination..............................................................................................178
Changing the Transmission Time ..........................................................................180
Changing the SMTP Server Setting.......................................................................182
Printing a File from Memory .............................................................................185
Resending a File ................................................................................................189
Confirming on Display............................................................................................191
Confirming by Report .............................................................................................192
Confirming by E-mail..............................................................................................193
Confirming by Report and E-mail...........................................................................193
Communication Failure Report ..............................................................................195
Confirming on Display............................................................................................196
Confirming by Report .............................................................................................197
Journal.................................................................................................................197
Print Journal.......................................................................................................198
Printing the Journal ................................................................................................198
All.........................................................................................................................199
Print per File No...................................................................................................200
Print per User ......................................................................................................201
Journal ...................................................................................................................203
Transmitting Journal by E-mail...............................................................................205
Journal by e-mail .................................................................................................205
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
(Print/Delete Stored Reception File) ..............................................................206
Printing Received and Stored Documents .............................................................207
Deleting Received and Stored Documents ............................................................208
Personal Boxes..................................................................................................211
Personal Boxes......................................................................................................211
Printing Personal Box Documents .........................................................................212
Confidential File Report..........................................................................................213
Information Boxes .............................................................................................214
Information Boxes ..................................................................................................214
Storing Documents in Information Boxes...............................................................215
Printing Information Box Documents......................................................................217
Deleting Information Box Documents.....................................................................218
Sending a Stored File ........................................................................................221
Storing a Document ...............................................................................................222
Programming a user name..................................................................................224
Setting a file name...............................................................................................225
Setting a password..............................................................................................225
Sending Stored Documents ...................................................................................226
Specifying documents from [File List]...................................................................229
Specifying documents by [User Name]..................................................................229
Specifying documents by [File Name] ...................................................................230
Displaying a preview............................................................................................230
Printing Stored Documents ....................................................................................231
Changing Stored Document Information................................................................233
Changing a user name ........................................................................................235
Changing the file name........................................................................................236
Changing the password.......................................................................................236
Deleting a Stored Document..................................................................................237
Before Use .............................................................................................................240
Using the Software.................................................................................................240
LAN-Fax Driver....................................................................................................240
Address Book ......................................................................................................241
LAN-Fax Cover Sheet Editor...............................................................................241
Auto Run program ...............................................................................................242
Installing Individual Applications ............................................................................242
Setting LAN-Fax Driver Properties.........................................................................243
Setting print properties ........................................................................................244
Making settings for option configuration..............................................................245
Basic Transmission................................................................................................246
Specifying a destination using a destination list ..................................................247
Specifying a destination using Address Book......................................................247
Specifying a destination by directly entering a fax number,
Internet Fax Destination, or IP-Fax destination.................................................248
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifying Options .................................................................................................249
To send a fax document at a specific time ..........................................................249
To print a sender stamp.......................................................................................250
To attach a cover sheet.......................................................................................250
To specify two-sided printing...............................................................................250
To display preview...............................................................................................250
Saving as files .....................................................................................................251
To store the fax document on the Document Server...........................................251
Confirming Transmission Results by E-mail ..........................................................252
LAN-Fax Result Report..........................................................................................253
Printing and Saving................................................................................................254
Editing Address Book.............................................................................................254
Programming new destinations ...........................................................................255
Editing programmed destinations........................................................................256
Deleting programmed destinations......................................................................256
Editing Fax Cover Sheets ......................................................................................258
Creating a cover sheet ........................................................................................258
Attaching a created cover sheet..........................................................................259
LAN-Fax Operation Messages...............................................................................260
Viewing received fax documents using a Web browser ......................................261
Printing fax information using a Web browser.....................................................262
Deleting fax information using a Web browser....................................................263
To add new receiver............................................................................................265
Delivering Files Received by Fax .....................................................................266
7. Appendix
Checking the Memory Status............................................................................267
Programs ............................................................................................................268
Registering and Changing Keystroke Programs....................................................268
Registering a priority function using a program...................................................270
Changing a program name..................................................................................271
Deleting a Program ................................................................................................272
Using a Program ....................................................................................................273
Optional Equipment...........................................................................................274
Expansion Memory (28MB: DIMM)........................................................................274
Handset..................................................................................................................274
Extra G3 Interface Unit...........................................................................................274
Specifications.....................................................................................................275
Maximum Values................................................................................................278
INDEX....................................................................................................... 280
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE
❖ Note to users in the United States of America
❖ Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communi-
cations. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio /TV technician for help.
❖ Caution:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
❖ Notice about the Telephone Consumer Protection Act (Valid in USA only)
The Telephone Consumer Protection Act of 1991 makes it unlawful for any
person to use a computer or other electronic device, including FAX ma-
chines, to send any message unless such message clearly contains in a mar-
gin at the top or bottom of each transmitted page or on the first page of the
transmission, the date and time it is sent and an identification of the busi-
ness or other entity, or other individual sending the message and the tele-
phone number of the sending machine or such business, other entity, or
individual. (The telephone number provided may not be a 900 number or
any other number for which charges exceed local or long-distance trans-
mission charges.)
In order to program this information into your FAX machine, you should
complete the following steps: Follow the FAX HEADER programming
procedure in the Programming chapter of the operating instructions to en-
ter the business identification and telephone number of the terminal or
business. This information is transmitted with your document by the FAX
HEADER feature. In addition to the information, be sure to program the
date and time into your machine.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
❖ Note to users in Canada
❖ Note:
This Class B digital apparatus complies with Canadian ICES-003.
❖ Remarque concernant les utilisateurs au Canada
❖ Avertissement:
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Caution
When using your telephone equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury to persons, includ-
ing the following:
• Do not use this product near water, for example, near a bath tub, wash bowl,
kitchen sink or laundry tub, in a wet basement or near a swimming pool.
• Avoid using a telephone during an electrical storm. There may be a remote
risk of electric shock from lightning.
• Do not use a telephone in the vicinity of a gas leak to report the leak.
• Use only the power cord and batteries indicated in this manual. Do not dis-
pose of batteries in a fire. They may explode. Check with local codes for pos-
sible special disposal instructions.
Save these instructions.
IMPORTANTES MESURES DE SÉCURITÉ
Certalnes mesures de sécurité doivent être prises pendant l’utilisation de matéri-
al téléphonique afin de réduire les risques d’incendle, de choc électrique et de
blessures. En voici quelquesunes:
• Ne pas utiliser l’appareil près de l’eau, p.ex., près d’une balgnoire, d’un lava-
bo, d’un évier de cuisine, d’un bac à laver, dans un sous-sol humide ou près
d’une piscine.
• Éviter d’utiliser le téléphone (sauf s’il s’agit d’un apparell sans fil) pendant un
orage électrique. Ceci peut présenter un risque de choc électrique causé par la
foudre.
• Ne pas utiliser l’appareil téléphonique pour signaler une fulte de gaz s’il est
situé près de la fuite.
• Utiliser seulement le cordon d’alimentation et le type de piles indiqués dans
ce manual. Ne pas jeter les piles dans le feu: elles peuvent exploser. Se con-
former aux ègrlements pertinents quant à l’élimination des piles.
Conserver ces instructions.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Read This Manual
Symbols
This manual uses the following symbols:
Indicates important safety notes.
Ignoring these notes could result in serious injury or death. Be sure to read these
notes. They can be found in the “Safety Information” section of About This Ma-
chine.
Indicates important safety notes.
Ignoring these notes could result in moderate or minor injury, or damage to the
machine or to property. Be sure to read these notes. They can be found in the
“Safety Information” section of About This Machine.
Indicates points to pay attention to when using the machine, and explanations
of likely causes of paper misfeeds, damage to originals, or loss of data. Be sure
to read these explanations.
Indicates supplementary explanations of the machine's functions, and instruc-
tions on resolving user errors.
This symbol is located at the end of sections. It indicates where you can find fur-
ther relevant information.
[ ]
Indicates the names of keys that appear on the machine's display panel.
{ }
Indicates the names of keys on the machine's control panel.
Names of Major Functions
This machine's major functions are referred to in this manual as follows:
• Internet Fax (by specifying an e-mail address) → Internet Fax
• Internet Fax (by specifying an IPv4 address) → IP-Fax
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Reading the Display
This section explains how to use control panel and screen-displayed keys.
The display guides you through operations, shows messages, machine status,
and destinations registered in the destination lists.
If you press the {Facsimile} or {Clear Modes} key during operation, the standby
display appears.
Note
❒ This machine automatically returns to standby mode if you do not use the
machine for a certain period of time. You can select the period using the Fac-
simile Auto Reset Timer in System Settings.
❒ You can have the machine return to standby mode after each transmission us-
ing User Parameters (switch 17, bit 3) in the Facsimile Features menu.
❒ To manually return to the standby display, do one of the following:
• If you have placed the original in the Auto Document Feeder (ADF) and
have not pressed the {Start} key, remove the original.
• If you have not placed an original, press the {Clear Modes} key.
• If you are in User Tools mode, press the {User Tools/Counter} key.
Reference
“System Settings”, General Settings Guide
“Facsimile Features”, General Settings Guide
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gener-
al Settings Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Reading the Display Panel and Using Keys
This section explains key functions and messages that appear on the control panel.
❖ Initial Display
ALV012S
1. Displays the date, time, and ma-
chine status. Displays the name, fac-
simile number of the destination,
and the size of the original when
transmitting.
6. Displays the entered number of a
destination.
7. Allows you to store documents in
the Document Server.
8. Press to display various informa-
When user authentication is set, a login
user name appears.
tion about communication.
9. Allows you to confirm the trans-
2. Allows you to send or print the
documents stored in the Document
Server.
mission settings.
10. Displays the percentage of free
memory space.
3. Allows you to set scan settings
and original feed types.
11. Allows you to search for a desti-
nation by destination name, fax
number, e-mail address or registra-
tion number.
4. Displays messages and the ma-
chine status.
5. Press this tab to switch the type of
transmission between fax/IP-Fax
and Internet Fax.
12. Switches transmission mode to
Immediate Transmission.
When [Immed. TX] is not highlighted, the
machine is in the Memory Transmission
mode.
When “Internet Fax Settings” is set to
“On” in the Facsimile Features menu,
appears.
• When [Fax] is selected, you can specify
fax numbers or IP-Fax destinations.
• When [Internet Fax] is selected, you can
specify e-mail addresses.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Allows you to set various fea-
17. Title word keys appear. Allows
you to switch from one page (dis-
play) to another on the destination
list.
tures for transmission.
14. Allows you to set a sender.
15. Allows you to check the number
of “Transmission Standby File(s)”,
“Memory Lock File(s)”, and “RX
Print Standby File(s)”.
18. Switches the title word keys.
19. Appears on Destination keys
programmed as a group destination.
16. Displays Quick Operation keys
set for frequently used functions. [TX
File Status] and [RX File Status] are pre-
set.
Note
❒ The display will differ depending on installed optional units.
❒ You can change “Internet Fax Settings” under “Initial Settings” in the Facsim-
ile Features menu.
❒ Information about documents sent using the facsimile function cannot be
p.13 “Transmission Modes”
p.221 “Storing a Document”
p.267 “Checking the Memory Status”
“Facsimile Features”, General Settings Guide
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gener-
al Settings Guide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Simplified Display
This section explains how to switch to the simplified display.
When you press the {Simplified Display} key, the screen changes from the initial
display to the simplified display.
Letters and keys are displayed at a larger size, making operations easier.
ALV021S
❖ Example of a simplified display
ALV013S
1. [Key Color]
Press to change the key color and in-
crease the brightness of the display panel.
Note
❒ To return to the initial display, press the {Simplified Display} key again.
❒ Certain keys do not appear on the simplified display.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Function List
This section explains various items that can be specified in the Facsimile Fea-
tures menu.
Press the {User Tools/Counter} key to display the Facsimile Features menu. For
details about the settings, see “Facsimile Features”, General Settings Guide.
❖ General Settings
Function name
Description
Quick Operation Key
Frequently used functions programmed as
Quick Operation keys are shown on the
menu immediately after the power is turned
on.
Switch Title
Select the title to be shown on the destination
list.
Search Destination
Communication Page Count
Adjust Sound Volume
Box Setting
Select a destination list to be used in “Search
Destination”.
Checks the transmission and reception, and
totals on the display.
Adjust the sound volume during On Hook
Mode and Immediate Transmission.
The following functions are for delivery and
transfer of documents: Personal Box, Infor-
mation Box, and Transfer Box.
Box Setting: Print List
You can print a list or the Personal Boxes, In-
formation Boxes, and Transfer Boxes cur-
rently programmed.
On Hook Mode Release Time
Use this function to specify a time to cancel
On Hook mode after you transmit using On
Hook dialing.
❖ Scan Settings
Function name
Description
Program / Change / Delete Scan Size
You can program, change, or cancel fre-
quently used scan sizes.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
❖ Send Settings
Function name
Description
Max. E-mail Size
Specify to limit the size of e-mail messages
that are transmitted, if receivers limit e-mail
size, or you cannot send large size e-mail for
some reason.
Program / Change / Delete Standard Mes- Program standard messages to be printed at
sage
the top of the first page of the original of the
opposite party.
Backup File TX Setting
You can specify whether or not to send to a
selected folder the backup of a file sent by
Memory Transmission.
❖ Reception Settings
Function name
Description
Switch Reception Mode
Program Special Sender
Specify the method for receiving fax documents.
By programming particular receivers as Spe-
cial Sender in advance, you can have Special
Senders treated differently.
Program Special Sender: Print List
Forwarding
You can print the Special Sender List.
Specify whether or not received fax docu-
ments are to be forwarded to a programmed
receiver.
Reception File Setting
Selects whether received documents are
saved on the hard disk to be printed later or
printed immediately without being saved.
Stored Reception File User Setting
The administrator can be specified for man-
aging documents stored on the machine after
fax documents are received.
SMTP RX File Delivery Settings
2 Sided Print
This function is available on systems that al-
low routing of e-mail received via SMTP.
Specify whether or not received fax docu-
ments are to be printed on both sides of the
paper.
Checkered Mark
Specify whether or not a checkered mark is
to be saved on the hard to be printed on the
first page of received fax documents.
Center Mark
Specify whether or not a center mark is to be
printed halfway down the left side and at the
top center of each page received.
Print Reception Time
Reception File Print Quantity
Specify whether or not the received date,
time, and file number are printed at the bot-
tom of received fax documents.
Specify the number of copies to be printed
for each fax document received.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Function name
Description
Paper Tray
Use this function to print fax documents re-
ceived from programmed senders and fax
documents from other senders, using differ-
ent paper trays.
Specify Tray for Lines
Specify a paper tray for each line (telephone,
Internet Fax, IP-Fax).
Folder Transfer Result Report
You can set whether the Folder Transfer Re-
sult Report is transmitted to the specified e-
mail address, when folders are programmed
as the forwarding destinations to which doc-
uments are sent from all senders or Special
Senders.
Memory Lock Reception
Switches the Memory Lock on or off.
❖ Initial Settings
Function name
Description
Parameter Setting
User Parameters allow you to customize var-
ious settings to suit your needs.
Parameter Setting: Print List
Program Closed Network Code
Program Memory Lock ID
Prints a list to see the current User Parameter
settings.
Register an ID required for Closed Network
communication.
Program a Memory Lock ID to be entered be-
fore printing documents when the Memory
Lock Reception function is activated.
Internet Fax Settings
Select Dial / Push Phone
Program Fax Information
Enable H.323
You can select to display the Internet Fax
icon or not.
Use this function to select a line type when
the machine is connected to a G3 analog line.
Program information to be shown on the display
of the other machine and printed as a report.
Specify whether or not H.323 is used for IP-
Fax transmission.
Enable SIP
Specify whether or not SIP is used for IP-Fax
transmission.
H.323 Settings
Set the IPv4 address or host name, and alias
telephone number of the gatekeeper.
SIP Settings
Set the SIP server's IPv4 address or host
name, and SIP user name.
Program / Change / Delete Gateway
Menu Protect
Register, change, or delete the gateway used
for transmission to IP-Fax.
Using Menu Protect, you can prevent unau-
thenticated users from changing the user
tools.
Reference
“Facsimile Features”, General Settings Guide
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Transmission
This section explains basic transmission operations such as specifying a trans-
mission mode or destination.
Transmission Modes
There are two types of transmission:
• Memory Transmission
• Immediate Transmission
Important
❒ It is recommended that you call the receiver and confirm with them when
sending important documents.
❖ Memory Transmission
Transmission starts automatically after the original is stored in memory. This
is convenient when you are in a hurry and want to take the document away
with you. You can also send the same original to several destinations.
❖ Immediate Transmission
Immediately dials the destination number, and while scanning the original,
sends it. It is very convenient when you want to send an original quickly or
when you want to check the destination you are sending to. When using this
type of transmission, the original is not stored in memory. You can only spec-
ify one address.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Normally the machine is in the Memory Transmission mode. To switch the
mode to Immediate Transmission, press [Immed. TX].
1
Note
❒ You can set the machine to enter Memory Transmission mode or Immediate
Transmission mode right after the power is turned on or the {Clear Modes} key
p.19 “Parallel Memory Transmission”
p.20 “Simultaneous Broadcast”
p.270 “Registering a priority function using a program”
Selecting Type of Transmission
You can select the transmission type: standard fax, IP-Fax, or Internet Fax.
Press the tab in the standby display to select the transmission type.
❖ When sending to a standard fax or IP-Fax destination
Make sure that [Fax] is selected.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission Modes
❖ When sending to an Internet Fax destination
Press [Internet Fax] to switch the type of transmission to Internet Fax.
1
p.25 “IP-Fax Functions”
p.29 “Internet Fax Functions”
Memory Transmission
Memory transmission mode has standard fax, Internet Fax and IP-Fax.
Important
❒ If there is a power failure (the main power switch is turned off) or the machine
is unplugged for about one hour, all the documents stored in memory are de-
leted. As soon as the main power switch is turned on, the Power Failure Re-
port is printed to help you identify deleted files. Simply turning off the power
by pressing the operation switch does not delete stored documents. See
“Troubleshooting When Using the Facsimile Function”, Troubleshooting.
❒ If memory is full (0% appears in “Memory” at the upper right of the screen),
Memory Transmission is disabled. Use Immediate Transmission instead.
A Make sure [Immed. TX] is not highlighted.
Normally Memory Transmission mode is selected.
B Place the original.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
C Make the scan settings you require.
1
D Using the number keys or a Destination key, specify a destination.
If you make a mistake, press the {Clear/Stop} key, and then enter the correct
number.
To select a destination from the Address Book, see “Using the Address Book
to Specify Destinations”.
E When sending the same original to several destinations (broadcasting),
press [Add] to specify the destinations.
You do not have to press [Add] when adding a destination using the destina-
tion list.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission Modes
F Specify the next destination.
1
Press [Fax] or [Internet Fax] to switch the transmission type between fax/IP-
Fax and Internet Fax.
A fax number, e-mail address and IP-Fax destination can be specified simul-
taneously.
G Press the {Start} key.
Note
❒ If the combined total number of programmed destinations exceeds the
maximum value, only Immediate Transmission is possible.
❒ For the maximum number of destinations you can specify per file, see
“Maximum Values”.
❒ For the maximum number of destinations you can specify for all files (in-
cluding files in memory), see “Maximum Values”.
❒ For the maximum number of documents you can store in memory for
Memory Transmission, see “Maximum Values”.
❒ For the maximum number of pages you can store in memory (using A4
p.67 “Sending by IP-Fax”
p.79 “Selecting Destinations from Recent Destinations”
p.278 “Maximum Values”
“Facsimile Features”, General Settings Guide
“Troubleshooting When Using the Facsimile Function”, Troubleshooting
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Sending multiple originals using the exposure glass
Follow these steps to send multiple originals using the exposure glass.
A Make sure [Immed. TX] is not highlighted.
1
B Place the first page of the original face down on the exposure glass.
C Specify a destination.
D Make the scan settings you require.
E Press the {Start} key.
The machine starts scanning.
F Place the next original on the exposure glass within 60 seconds after the ma-
chine has finished scanning the first original.
G Repeat steps to for all originals.
D
F
H Place the last original, and then press the {q} key.
The machine dials the destination and starts transmission.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission Modes
Parallel Memory Transmission
This function dials while the original is being scanned.
Standard Memory Transmission stores the original in memory, then dials the
destination. However, Parallel Memory Transmission allows you to confirm the
connection status quickly. In addition, this function scans the original faster than
Immediate Transmission. This is useful when you are in a hurry and need to use
the original for another purpose.
1
Important
❒ Standard Memory Transmission is used instead of Parallel Memory Trans-
mission in the following cases:
• When the line is busy and could not be connected to
• With Send Later
• When you store an original for Memory Transmission while another com-
munication is in progress
• When two or more destinations are specified
• When an original is placed on the exposure glass, and then sent
• When you send documents stored in the Document Server
Note
❒ You can turn this function on or off with the User Parameters (switch 07, bit
2) in the Facsimile Features menu.
❒ Standard Memory Transmission may be used instead of Parallel Memory
Transmission depending on the optional equipment installed if there is not
enough free memory left.
❒ If you use this function, the Memory Storage Report will not be printed.
❒ If the {Clear/Stop} key is pressed, the original will jam or memory will run out
while Parallel Memory Transmission stops. The Communication Result Re-
port is printed and files are deleted.
❒ When using Parallel Memory Transmission, only the page number is printed
on the header of the fax, the total number of originals is not automatically
printed.
Reference
“Facsimile Features”, General Settings Guide
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Automatic Redial
If a fax document could not be sent because the line was busy or an error oc-
curred during transmission, the line is switched to another at five-minute inter-
vals and redial is attempted up to five times.
1
If redialing fails after four redials, the machine cancels the transmission and
prints a Communication Result Report or Communication Failure Report.
Note
❒ If there are a large number of files stored in memory, documents might not be
sent in the order they were scanned.
Dual Access
The machine can scan other documents into memory even while sending a fax
document from memory, receiving a document into memory, or automatically
printing a report. Since the machine starts sending the second document imme-
diately after the current transmission ends, the line is used efficiently.
Note
❒ During Immediate Transmission or when in User Tools mode, the machine
cannot scan an original.
Simultaneous Broadcast
Use this function to send the same original to multiple destinations simulta-
neously.
To specify multiple destinations, specify the first destination, and then specify
the next destination by pressing [Add].
If you dial several destinations for the same document (broadcasting), the docu-
ments are sent in the order in which they were dialed. If the fax document could
not be transmitted, the machine redials that destination after the last destination
specified for broadcasting. For example, if you specify four destinations, A
through D, for broadcasting, and if the lines to destinations A and C are busy,
the machine dials the destinations in the following order: A, B, C, D, A, and C.
To check the transmission progress, print the TX file list.
If the optional extra G3 interface unit is installed, you can use the Simultaneous
Broadcast function to send faxes simultaneously on different phone lines.
If you specify a second transmission while broadcasting to several destinations,
faxes are transmitted alternately to each remaining destination in the current
and second broadcast.
For example, if you specify a broadcast to destinations A and B, and then specify
a broadcast to destinations C and D while transmission to destination A is in
progress, the machine sends the faxes in the following order: A, C, B, and then D.
If the previous file and next file are both on standby, these are also sent in the
same order.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission Modes
Note
❒ To avoid accidentally pressing the wrong Destination key, you can set the
machine so that each time a destination is added using a Destination key,
[Add] must be pressed. Make the setting in User Parameters (switch 17, bit 2)
in the Facsimile Features menu.
1
p.63 “Simultaneous Broadcast Using Multiple Line Ports”
p.187 “Printing a List of Files in Memory (Print TX File List)”
Immediate Transmission
Immediate Transmission is possible with standard fax transmission and IP-Fax
transmission.
Important
❒ Internet Fax is executed in only Memory Transmission that starts transmis-
sion automatically after storing documents in memory. If you switch the type
of transmission to Internet Fax while the machine is in the Immediate Trans-
mission mode, the transmission mode is automatically switched to the Mem-
ory Transmission mode.
❒ Group cannot be used for Immediate Transmission. You cannot send the
same document to multiple destinations (broadcasting). If you specify broad-
cast or transmission for a group, the machine changes automatically to Mem-
ory Transmission.
A Press [Immed. TX].
B Place the original.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
C Select the scan settings you require.
1
D Using the number keys or a Destination key, specify a destination.
If you make a mistake, press the {Clear/Stop} key, and then enter the correct
number.
To select a destination from the Address Book, see “Using the Address Book
to Specify Destinations”.
E Press the {Start} key.
The machine dials a destination.
Note
p.67 “Sending by IP-Fax”
p.78 “Specifying Group Destinations”
p.79 “Selecting Destinations from Recent Destinations”
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission Modes
Sending multiple originals using the exposure glass
Follow these steps to send multiple originals using the exposure glass.
A Press [Immed. TX].
1
B Place the first page face down on the exposure glass.
C Specify a destination.
D Make the scan settings you require.
E Press the {Start} key.
F Place the next original on the exposure glass within 10 seconds after the ma-
chine has finished scanning the first original.
G Repeat steps to for all originals.
D
F
H Place the last original, and then press the {q} key.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Displaying Confirmation of Transmission
On this screen you can check the destination, transmission mode, and other
transmission settings before transmitting.
1
A Press [Check Modes], and then check the transmission settings.
The following display appears.
B After checking the settings on the display, press [Exit].
24
Download from Www.Somanuals.com. All Manuals Search And Download.
IP-Fax Functions
IP-Fax Functions
The IP-Fax function sends or receives documents between two facsimiles direct-
ly via a TCP/IP network.
1
This function has the following advantages and is suitable for communication
within the same LAN:
• Reducing communication costs
• Communicating between IP-Faxes at higher speed than by standard fax
IP-Fax uses SIP and H.323 as the network protocol.
Specify an IPv4 address or host name instead of a fax number for sending. When
using a gatekeeper, specify its alias telephone number. Specify addresses of the
gatekeeper or SIP server (proxy server, register server, redirect server) as appro-
priate in Initial Settings in the Facsimile Features menu.
When using a SIP server, you can send by specifying SIP user name.
You can also transmit to a G3 facsimile connected to the public switched tele-
phone network (PSTN) via a gateway (T.38-compliant).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
You can receive IP-Faxes in the same manner as standard faxes.
1
ALT001S
Important
❒ To use IP-Fax functions, this machine must be connected to a LAN and set up
correctly under Initial Settings in the Facsimile Features menu.
❒ The facsimile function of this machine cannot be used with IPv6.
❒ Before using this function, configure the network in the System Settings
menu.
Note
❒ IP-Fax supported by this machine is ITU-T Recommendation T.38 compliant.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
IP-Fax Functions
Reference
p.147 “Types of Reception”
“Connecting the Machine”, General Settings Guide
“System Settings”, General Settings Guide
“Facsimile Features”, General Settings Guide
1
Terminology
The following are words you should know when using IP-Fax:
❖ H.323
A multimedia communication protocol that sends or receives files via one-to-
one communication over a LAN or the Internet.
❖ SIP
A communication control protocol for Internet telephone that utilizes VoIP
(which converts voice information to IP packets) and is equipped with func-
tions such as creating, modifying, and terminating sessions with one or more
participants.
❖ Gatekeeper (VoIP gatekeeper)
A gatekeeper manages devices connected to an IP network and converts alias
telephone numbers to IPv4 addresses and performs authentication functions.
In addition, a gatekeeper governs band (transmission rate assignment) and
access control.
❖ SIP server
A SIP server mediates connection requests between devices connected to an
IP network and is composed mainly of servers that have the following three
functions:
• Proxy server: Receives SIP requests and forwards them on behalf of the re-
questor.
• Register server: Receives information about a device's address within an IP
network and registers them in the database.
• Redirect server: Used to inquire the destination address.
❖ Gateway (VoIP gateway)
A gateway connecting a telephone network and IP network, it has functions
such as protocol conversion for connecting these different networks, and also
connects communication devices (telephones, facsimiles, etc.) to a LAN or
other network.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Notes on Using IP-Fax
The following are notes about using IP-Fax:
• You may not be able to send to a firewall-protected network.
• You cannot use telephones on a LAN.
1
• If a power outage lasts about an hour, or the machine is disconnected from
the power outlet for about an hour, documents stored in the fax machine's
memory are deleted. If any document is deleted, the Power Failure Report is
automatically printed out when the main power switch is turned on. Use this
report to check which documents were deleted. Simply turning off the power
by pressing the operation switch does not delete stored documents. See
“Troubleshooting When Using the Facsimile Function”, Troubleshooting.
Reference
“Troubleshooting When Using the Facsimile Function”, Troubleshooting
Functions Not Available for IP-Fax Transmission
You can use the following functions with standard fax transmission, but not IP-
Fax transmission:
• On hook dial
• Manual dial
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Internet Fax Functions
Internet Fax Functions
This machine converts scanned document images to e-mail format and transmits
the data over the Internet.
1
The e-mail sent by this machine can be received by another Internet Fax ma-
chine. Instead of dialing the telephone number of the destination you want to
send to, you enter the relevant e-mail address.
You can also print or forward received e-mail messages.
ALT002S
Important
❒ To use Internet Fax functions, this machine must be connected to a LAN and
set up correctly in “System Settings”.
❒ The facsimile function of this machine cannot be used with IPv6.
❒ To send Internet Fax documents, in the Facsimile Features menu, under Ini-
tial Settings, set [Internet Fax Settings] to [On]. However, documents can still be
forwarded or delivered to Internet Fax destinations even if [Off] is selected.
❒ To receive Internet Fax documents, in the System Settings menu, in File
Transfer, under [Fax E-mail Account], set [Account] to [Receive].
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Note
❒ The Internet Fax function supported by this machine is compliant with ITU-
T Recommendation T.37.
❒ You can receive e-mail messages with an attached TIFF-F image from com-
1
puters.
❒ Though Internet Fax documents are normally sent via an SMTP server, you
can also send Internet Fax documents directly to their destinations without
going through an SMTP server. To do this, set whether or not to bypass the
SMTP server on the standby display.
❒ When sending Internet Fax documents, “Subject”, “Text”, “Reception No-
tice”, and “BCC Transmission” can be selected in [TX Mode].
❒ You can limit the size of transmitted e-mail messages in “Send Settings” of
“Facsimile Features”.
❒ See “Received Images” for how e-mail is actually received by the computer.
❒ For details about how to confirm the transmission result, see “Checking the
p.125 “Requesting a Reception Notice”
p.155 “Received Images”
p.191 “Checking the Transmission Result (Transmission File Status)”
“Connecting the Machine”, General Settings Guide
“System Settings”, General Settings Guide
“Facsimile Features”, General Settings Guide
Notes on Using Internet Fax
The following are notes about using Internet Fax:
• When using the Internet Fax function, originals are sent at A4 size. Originals
larger than A4 are reduced to A4 size. If the receiver is in compliance with the
T.37 full mode, originals are sent at the size specified in the Address Book.
• When using Internet Fax transmission, documents are sent at “Detail” resolu-
tion, even if you specify “Super Fine”. To send documents at “Super Fine”,
specify this resolution when registering the destination in the Address Book.
• If a transmission is not successful, this machine usually receives an e-mail er-
ror notification. However, e-mail error notifications may not be transmitted
for various reasons. It is recommended that you confirm receipt of important
document by calling the other party.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Internet Fax Functions
• The level of security for Internet communications is low. It is recommended
that you use the telephone network for confidential communications.
• Voice communication is not supported over a LAN.
• Internet Fax delivery might be delayed due to network congestion. Use Inter-
net Fax transmission that bypasses the SMTP server, a public telephone line
fax, or IP-Fax whenever communication time is a concern.
1
• If a power outage lasts about an hour, or the machine is disconnected from
the power outlet for about an hour, documents stored in the fax machine's
memory are deleted. If any document is deleted, the Power Failure Report is
automatically printed out when the main power switch is turned on. Use this
report to check which documents were deleted. Simply turning off the power
by pressing the operation switch does not delete stored documents. See
“Troubleshooting When Using the Facsimile Function”, Troubleshooting.
• You may not be able to send large files as e-mail, depending on e-mail envi-
ronment conditions.
• When available memory is low, you may not be able to send Internet Fax doc-
uments.
• Because the machine sends documents as e-mail messages with an attached
TIFF-F image, viewer applications are required in order to view documents
when they are received on a computer.
• With a large volume of document, it may take some time before transmission
starts. This is due to the time the machine requires to convert the data in mem-
ory.
p.33 “T.37 Full Mode”
p.41 “Paper Size and Scanned Area”
p.73 “Bypassing the SMTP server”
“Troubleshooting When Using the Facsimile Function”, Troubleshooting
Functions Not Available by E-mail Transmission
The following functions are supported with standard fax transmission, but not
with Internet Faxing.
• Immediate Transmission
• ID Transmission
• Transmission by SUB Code
• On Hook Dial
• Manual Dial
• JBIG Transmission
• ECM (Error Correction Mode)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Functions Not Available by E-mail Reception
The following functions are supported with standard fax reception, but not with
Internet Faxing.
1
• Memory Lock Reception
• SEP Code Reception
• Authorized Reception per Sender
• Reception File Print Quantity per Sender
E-mail Subject
If you send e-mail without specifying a subject, a subject is automatically insert-
ed. Subjects differ depending on Stamp Sender Name settings.
❖ When Stamp Sender Name is set to on:
From Sender Name(Fax Message NO.xxxx)
❖ When Stamp Sender Name is set to off:
• If Own Fax Number and Own Name are programmed:
From “Own Fax Number”(“Own Name”)(Fax Message NO.xxxx)
• If only Own Fax Number is programmed:
From “Own Fax Number”(Fax Message NO.xxxx)
• If only Own Name is programmed:
From “Own Name”(Fax Message NO.xxxx)
• If neither Own Fax Number nor Own Name are programmed:
Fax Message NO.xxxx
Note
Reference
p.123 “Other Transmission Features”
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Internet Fax Functions
T.37 Full Mode
This machine is T.37 full mode compatible. T.37 full mode is an international
standard for Internet Fax transmission. (ITU-T Recommendation, RFC2532)
1
When an Internet Fax communication is made between T.37 full mode compat-
ible machines, the receiver side sends the return receipt (dispatched) in response
to the reception notice request attached to the sent e-mail. This return receipt in-
cludes the receiver's reception capability information (compression type, paper
size, and resolution). When the receiver is programmed in the Address Book as
the full mode destination, the sender side automatically registers the received in-
formation in the Address Book. This allows you to send a subsequent Internet
Fax document to that receiver based on this information.
❖ Returning a Return Receipt
When e-mail is received, if the sender requests reception notice, the receiver
sends a return receipt that includes the receiving machine's capability (com-
pression type, paper size, and resolution).
❖ Registering the Received Reception Confirmation Contents
When the sender receives the return receipt that includes the receiver's recep-
tion capability, the sender checks that the final recipient address sent is pro-
grammed in the Address Book. If it is programmed as a full mode destination,
the sender automatically registers the receiver's reception capability. The reg-
istered reception capability is updated each time the sender receives new re-
ception capability information. The sender can send documents to the
receiver based on this information.
If the receiver is programmed as the simple mode machine or not pro-
grammed in the Address Book, the receiver's reception capability cannot be
registered.
If you know the receiver's reception capability, you can set it manually.
❖ Requesting a Reception Notice
When the receiver's machine supports T.37 full mode and is programmed as
a full mode machine in the Address Book, the machine requests the reception
notice from the receiver. Then, the machine will receive the return receipt
(sent) that includes the receiver's reception capability.
Note
❒ Use Web Image Monitor to manually program a receiver's reception capabil-
ity information.
❒ If you use Internet Fax transmission, you can send documents to multiple
destinations at once. However, if you specify full mode destinations, since
each destination may have a different reception capability, transmission is
p.125 “Requesting a Reception Notice”
p.263 “Programming Destination Information from Web Browser”
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Placing Originals
Place the original on the exposure glass or the ADF. For details about how to
place originals, see the following:
1
• Placing originals on the exposure glass
“Placing Originals on the Exposure Glass”, Copy/Document Server Refer-
ence
• Placing originals into the ADF
“Placing Originals in the Auto Document Feeder”, Copy/Document Server
Reference
“Non-compatible originals for the Auto Document Feeder”, Copy/Docu-
ment Server Reference
Note that [Special Original] of the copy function cannot be used with the facsimile
function.
Place the originals according to their paper size.
Original size
Placing on the exposure glass
Placing into the ADF
A4, B4 JIS, A3, 8 1/2"×11",
8 1/2"×14", 11"×17"
A4, B4 JIS, A3, 8 1/2"×11",
8 1/2"×14", 11"×17"
A5, B5 JIS
A5, B5 JIS
Important
❒ If you place A5 size originals on the exposure glass, they are not detected.
Place A5 size originals into the ADF.
❒ Do not lift the ADF while using it to scan originals.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing Originals
Note
❒ To scan multiple originals using the Auto Document Feeder (ADF), set origi-
nals in a stack.
❒ When sending a fax, the image output at the other end depends on the size
and orientation of paper used in the receiver's machine. If the receiver does
not use paper of the same size and orientation as that of the original, the fax
image may be reduced in size, trimmed at both edges, or divided across two
or more sheets. When sending an important original, ask the receiver about
the size and orientation of the paper in their machine.
1
❒ When sending an original of irregular (i.e. custom) size or part of a large orig-
inal, you can specify the scan area precisely.
❒ Custom size originals are scanned as regular size originals, so the receiver
may find extra blank margins or edges of images missing. If you specify a
scan area, only that area is scanned regardless of the actual size of the original.
❒ Documents longer than 800 mm (32") must be sent by Memory Transmission
(Immediate Transmission may not be possible).
❒ If an original jams, press the {Clear/Stop} key, and then carefully remove the
original.
❒ Make sure that all ink, correcting fluid etc., has completely dried before plac-
ing your original. If it is still wet, the exposure glass will become marked and
those marks will appear on the received image.
❒ Generally, place A4, 8 1/2"×11" originals in the landscape orientation (L). If
you place an A4, 8 1/2"×11" original in the portrait orientation (K), the image
is sent rotated by 90°.
❒ You can send the first page from the exposure glass then the remaining pages
from the ADF. You cannot change from the ADF to the exposure glass.
❒ When using the Internet Fax function, originals are sent at A4 size. Originals
larger than A4 are reduced to A4 size. If the receiver's machine is compliant
with the T.37 full mode, originals are sent at the size specified in the Address
Book.
❒ Information about this machine is printed at the destination. This information
is printed on the side of the paper that is to your left when placing the docu-
ments on the exposure glass or the ADF. However, the information is also
printed rotated by 90 degrees if an A4, 8 1/2"×11" original is placed in the por-
trait orientation (K).
❒ For acceptable types of originals, see “Acceptable Original Sizes”, “Paper Size
and Scanned Area” and “Original Sizes Difficult to Detect”.
❒ You can set the original feed types that are selected right after the power is
turned on or the {Clear Modes} key is pressed. See “Registering a priority func-
tion using a program”.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
p.33 “T.37 Full Mode”
1
p.41 “Paper Size and Scanned Area”
p.51 “Scan Size”
p.270 “Registering a priority function using a program”
“Facsimile Features”, General Settings Guide
“Placing Originals”, Copy/Document Server Reference
Setting the Original Orientation
When you store documents in the Document Server, set “Original Orientation”.
A Place the original, and then select the scan settings you require.
B Press [Original Feed Type].
C Specify the original orientation.
Check the orientation of the placed document, and then press [
] or [
].
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing Originals
D Press [OK].
The selected original orientation appears in “Original Feed Type”.
1
Reference
p.221 “Storing a Document”
Scanning Two-Sided Originals
Use this function to send two-sided originals.
The front and back of the scanned original will be printed in order on separate
sheets at the other end. The orientation of alternate sheets may be reversed at the
other end. If you want to print the original with the same orientation at the other
end, specify the “Original position” and “Page opening orientation”.
Important
❒ Two-sided originals cannot be sent by using just the exposure glass.
❒ Two-sided originals are only sent with Memory Transmission. Immediate
Transmission is not possible.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
A Place the original, and then select the scan settings you require.
B Press [Original Feed Type].
1
C Specify the original orientation.
Check the orientation of the placed document, and then press [
] or [
].
Make sure that the specified original orientation matches the orientation of
originals loaded in the ADF.
D Press [2 Sided Original].
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing Originals
E Select [Top to Top] or [Top to Bottom].
1
To cancel two-sided transmission, press [1 Sided Original]. The display returns
to that of step .
D
Select [2nd Sheet] if you want to send a cover sheet as the first page.
G Press [OK].
“2 Sided Original” appears above [Original Feed Type].
H Specify a destination, and then press the {Start} key.
Note
❒ You can confirm whether both sides were properly scanned using the
Stamp function.
❒ You can set the original feed types that are selected right after the power is
turned on or the {Clear Modes} key is pressed. See “Registering a priority
p.45 “Stamp”
p.270 “Registering a priority function using a program”
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Acceptable Original Sizes
Where original is set Acceptable original size
Maximum
number of
sheets
Paper thickness
1
Exposure glass
Up to A3 (297 × 420 mm),
11" × 17" (279 × 432 mm)
1
----
40-128 g/m2
ADF, one-sided docu- A5 L to A3 L
ment (up to 1200 mm long)
50 sheets
(80 g/m2, 20 lb) (11-34 lb)
51/2" × 81/2" K to 11" × 17"L
52-105 g/m2
50 sheets
(80 g/m2, 20 lb) (14-28 lb)
ADF, two-sided docu- A5 L to A3 L
ment (up to 432 mm long)
51/2" × 81/2" K to 11" × 17"L
Note
❒
The weight range for originals in the Mixed Original Sizes mode is 52–81 g/m2,
13.8–21.5 lb.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing Originals
Paper Size and Scanned Area
Important
❒ If you place an original larger than A3, 11"×17" on the exposure glass, only an
A3, 11"×17" area is scanned.
1
❖ Exposure Glass
❖ ADF
AAG019S
❖ Maximum scan area
The following shows the maximum scan area:
• Memory Transmission: 297 × 1200 mm/11" × 47" (W × L) from the ADF
• Immediate Transmission: 297 × 1200 mm/11" × 47" (W × L) from the ADF
• 297 × 432 mm/11" × 17" (W × L) (from the exposure glass)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Note
❒ There may be a difference in the size of the image when it is printed at the des-
tination.
❒ Even if an original is correctly placed on the exposure glass or in the ADF, a
1
margin of 3 mm (0.1") around each edge of the original may not be sent.
❒ If the receiver uses paper of a smaller width than the original, the image is re-
duced to fit that paper.
❒ During Immediate Transmission, the length of the scanning range can be-
come narrower than 1200 mm (47"), depending on the resolution as well as
the settings on the destination machine.
❒ The machine detects paper sizes in the following ways:
• When you place an original in the ADF, an original wider than about 263
mm (10.4") is scanned as A3, 11"×17" size.
An original narrower than about 230 mm (9.1") is sent as 81/2"×11" or
81/2"×14" size, and an original narrower than about 263 mm (10.4") is
scanned as B4 JIS (Japanese Industrial Standard).
Originals up to 1200 mm (47.2") in length can be scanned.
• See the following table for sizes the machine can detect when you place an
original on the exposure glass. Because the machine scans custom size doc-
uments in a standard size, part of the image may be truncated depending
on the length of the document. For details about how to set custom size
documents, see “Scan Size”.
❖ Metric Version
❖ Inch Version
× - Unable to auto detect
*1 Normally a length of about 420 mm (16.5") can be scanned; however, it is only
possible to specify a scanning size up to 432 mm (17").
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing Originals
Reference
p.51 “Scan Size”
Original Sizes Difficult to Detect
1
The machine has difficulty detecting the size of the following kinds of originals.
(When this happens, the receiving machine may not select print paper of the cor-
rect size.)
• documents placed on the exposure glass of sizes other than those listed in the
following table
• originals with index tabs, tags, or protruding parts
• transparent originals, such as OHP transparencies or translucent paper
• dark originals with dense text or drawings
• originals that contain areas of solid print
• originals that have solid print around their edges
• originals with glossy surfaces
• bound originals of more than 10 mm (0.3") in thickness, such as books.
The following paper sizes are automatically detected in facsimile mode.
❖ Metric Version
8 1/2"×13"
Paper size
where orig-
inal is
A3L
B4 JISL
A4KL
B5 JISKL
A5KL
(F4)
placed
Exposure
glass
×
ADF
- Auto detect
× - Unable to auto detect
❖ Inch Version
8 1/2"×14" L
8 1/2"×11" KL
5 1/2"×8 1/2" K
Paper size where
original is placed
11"×17"L
Exposure glass
ADF
×
- Auto detect
× - Unable to auto detect
Note
❒ You can select from 81/2" × 13", 81/4" × 13", 8" × 13" with User Tools (System
Settings). See “System Settings”, General Settings Guide.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Reference
“System Settings”, General Settings Guide
Transmission with Image Rotation
1
Generally, place A4, 81/2"×11" originals in the landscape orientation (L). If you
place an A4, 81/2"×11" original in the portrait orientation (K), the image is sent
rotated by 90°. Providing the receiver has A4, 81/2"×11" landscape paper (L),
the document is printed the same size as the original.
Note
❒ This function is unavailable with Immediate Transmission.
❒ When Image Rotation is used, all documents are sent by normal Memory
Transmission.
❒ This function is unavailable when using Mixed Original Sizes.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing Originals
Stamp
When sending a fax document using the ADF, the machine can stamp a circle
mark at the bottom of the original. When sending a two-sided document, the
document is marked at the bottom of the front page and top of the rear page.
1
Important
❒ Stamp only works when scanning from the ADF.
A Place the original, and then select the scan settings you require.
B Press [Original Feed Type].
C Press [Stamp].
To cancel the stamp, press [Stamp] again before pressing [OK].
D Press [OK].
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
E Specify the destination, and then press the {Start} key.
Note
❒ This stamp indicates that the original has been successfully stored in mem-
ory for Memory Transmission, or successfully sent by Immediate Trans-
mission.
1
❒ When the stamp starts getting lighter, replace the cartridge.
❒ If a multi-page feed or paper jam occurs, the originals are not sent properly
and not stamped. If you find a page that is not stamped, send only that
page again.
❒ You can have the machine select the Stamp function right after the power
is turned on or the {Clear Modes} key is pressed. See “Registering a priority
function using a program”.
❒ You can program one of the Quick Operation keys with operations for this
function. Using the Quick Operation key allows you to omit step .
B
❒ A paper jam during Parallel Memory Transmission may cause the trans-
mission to fail even if stamping is performed.
❒ You cannot turn the Stamp function on or off while an original is being
scanned.
Reference
p.270 “Registering a priority function using a program”
“Facsimile Features”, General Settings Guide
“Adding Paper, Toner and Staples”, Troubleshooting
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Settings
Scan Settings
You may want to send many different types of fax documents. Some of these
may be difficult to reproduce at the receiver's end. However, the machine has
three settings that you can adjust to help you transmit the document with the
best possible image quality.
1
❖ Scan Type:
Text, Text / Line Art, Text / Photo, Photo
❖ Resolution:
Standard, Detail, Super Fine (optional)
❖ Scan Size:
Auto Detect, Regular, Area, Mixed Original Sizes
❖ Density (Contrast):
Auto Density, Manual Density (seven levels), Combined Auto and Manual
Density
Scan Type
If the original contains photographs, illustrations, or diagrams with complex
shading patterns or grays, select the appropriate scan type to optimize image
clarity.
❖ Text
Select [Text] to send high-contrast black-and-white image originals. Use this
setting when you only want to send clearer text, even if the original contains
text and photographs.
❖ Text / Line Art
Select [Text / Line Art] to send high-contrast black-and-white graphic originals
at improved resolution. The [Text] mode gives priority to scanning speed;
[Text / Line Art] mode gives priority to scanning quality.
❖ Text / Photo
Select [Text / Photo] to send an original containing both a high-contrast black-
and-white image, such as text, and a halftone image, such as a photograph.
❖ Photo
Select [Photo] to send an original containing a halftone image, such as a pho-
tograph or a color original.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
A Press [Scan Settings].
1
B Make sure that [Scan Type] is selected.
C Select the scan type you require, and then press [OK].
Note
❒ If you select [Text / Line Art], [Text / Photo], or [Photo], the transmission will
take longer than when [Text] is selected.
❒ If you send a fax document with [Text / Line Art], [Text / Photo], or [Photo] and
the background of the received image is dirty, reduce the density setting
and resend the fax.
❒ You can set the scan type that is selected right after the machine is turned
on or the {Clear Modes} key is pressed. See “Registering a priority function
using a program”.
p.58 “Density (Contrast)”
p.270 “Registering a priority function using a program”
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Settings
JBIG Transmission
If you use JBIG (Joint Bi-level Image experts Group) compression, you can send
originals scanned using [Photo] faster than with other compression methods.
1
Important
❒ This function is not available with Internet Fax function.
❒ This function requires that the other party's fax machine has both the JBIG
function and ECM function (G3 communication only).
Resolution
This section explains how to set the resolution of the original.
Images and text are scanned into the machine by converting them to a sequence
of dots. The density of the dots determines the quality of the image and how long
it takes to transmit. Therefore, images scanned at high resolution (Super Fine)
have high quality but transmission takes longer. Conversely, low resolution
(Standard) scanning results in lower quality but the original is sent more quick-
ly. Select the setting that matches your needs based upon this trade off between
speed and image clarity.
❖ Standard (8 x 3.85 lines/mm, 200 x 100 dpi)
Select for originals containing normal size characters.
❖ Detail (8 x 7.7 lines/mm, 200 x 200 dpi)
Select for originals containing small characters or when you require greater
clarity. This resolution is twice as fine as Standard.
❖ Super Fine (optional expansion memory required: 16 x 15.4 lines/mm, 400 x 400 dpi)
Select for originals with very fine details or when you require the best possi-
ble image clarity. This resolution is eight times finer than Standard.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
A Press [Scan Settings].
1
B Press [Resolution].
C Select the resolution you require, and then press [OK].
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Settings
Note
❒ If you install the optional expansion memory, “Super Fine” appears in the
Resolution box.
❒ If the other party's machine does not support the resolution at which you
are sending, this machine automatically switches to a resolution that is
supported. You can check the resolution at which you actually sent by
printing the Journal.
1
❒ Sending with Super Fine resolution requires that the machine has the op-
tional expansion memory, and the other party's machine has the capability
to receive fax documents at Super Fine resolution.
❒ The machine supports Standard, Detail, and Super Fine (with the optional
expansion memory) resolutions.
❒ You can set the resolution type that is selected right after the machine is
turned on or the {Clear Modes} key is pressed. See “Registering a priority
function using a program”.
❒ When using Internet Fax transmission, documents are sent at “Detail” res-
olution, even if you have specified “Super Fine”. To send a document at
“Super Fine”, configure the Full Mode when registering the destinations in
p.33 “T.37 Full Mode”
p.198 “Print Journal”
p.270 “Registering a priority function using a program”
Scan Size
Normally, a placed original is scanned according to the automatically detected
size. If a scan area is specified, the original is scanned accordingly. Thus, origi-
nals can be sent without extra space or blank margins.
Note
❒ When placing different size originals into the ADF, adjust the document
guide to the largest original.
❒ Small-size originals may be sent at a slight slant since they do not match the
Reference
p.43 “Original Sizes Difficult to Detect”
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Auto Detect
Detects the size of the first page and scans all pages using that size.
If the machine cannot detect the original size, a confirmation message appears.
Place the original again.
1
A Place the originals.
B Press [Scan Settings].
C Press [Scan Size].
D Make sure that [Auto Detect] is selected.
If it is not, press [Auto Detect].
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Settings
E Press [OK].
1
“Auto Detect: Same Size” appears above [Scan Settings].
F Specify a destination and press the {Start} key.
Regular
The placed original is scanned according to specified size regardless of actual
size.
The sizes that can be specified are A4KL, B4 JISL, A3L, 81/2"×11"KL,
81/2"×14"L, and 11"×17"L.
A Place the originals.
B Press [Scan Settings].
C Press [Scan Size].
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
D Press the size of the originals to be sent.
1
81/2"×11" indicates LT. 81/2"×14" indicates LG. 11"×17" indicates DLT.
E Press [OK].
The selected size appears above [Scan Settings].
F Specify a destination and press the {Start} key.
Note
❒ To cancel the selected scan size, select [Auto Detect].
Area
Program the sizes of the originals to be scanned in advance. Only the area in the
specified size is scanned regardless of the actual size of a placed original.
A Place the originals.
B Press [Scan Settings].
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Settings
C Press [Scan Size].
D Press [Area 1] or [Area 2].
E Press [OK].
1
The specified size appears above [Scan Settings].
F Specify a destination and press the {Start} key.
Note
❒ To cancel the selected scan size, select [Auto Detect].
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Mixed Original Sizes
Select this to individually scan the size of originals loaded into the ADF. For ex-
ample, when A3Land A4Ksize originals are sent together, usually all are sent
using the size of the first original. By selecting Mixed Original Sizes, the machine
scans and sends each original according to its size.
1
A Place the originals.
B Press [Scan Settings].
C Press [Scan Size].
D Press [Mixed Original Sizes].
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Settings
E Press [OK].
1
“Auto Detect: Mixed Sizes” appears above [Scan Settings].
F Specify a destination and press the {Start} key.
Note
❒ To cancel Mixed Original Sizes, press [Mixed Original Sizes] again.
❒ You can combine the original sizes as follows: A3Land A4K, B4 JISLand
B5 JISK, A4Land A5K.
❒ When using Mixed Original Sizes, the machine sends the originals by
Memory Transmission.
❒ When using Mixed Original Sizes, rotation transmission is disabled.
❒ You can have the machine select Mixed Original Sizes right after the power
is turned on or the {Clear Modes} key is pressed. See “Registering a priority
function using a program”.
p.44 “Transmission with Image Rotation”
p.270 “Registering a priority function using a program”
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Density (Contrast)
The text and diagrams on originals should stand out clearly from the paper they
are on. If the original has a darker background than normal (for example, a
newspaper clipping), or if the writing is faint, adjust the density.
1
❖ Auto Density
The appropriate density setting for the original is automatically selected.
A Make sure that [Auto Density] is selected.
❖ Manual Density
Use manual density to set density manually.
You can select one of seven density levels.
A If [Auto Density] is selected, press [Auto Density] to turn it off.
B Press [W] or [V] to adjust the density.
The cursor moves.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Settings
❖ Combined Auto and Manual Density
You can only adjust density for photographs, illustrations, or diagrams if the
original has a dark background.
You can select one of seven density levels.
A Make sure that [Auto Density] is selected.
1
B Press [W] or [V] to adjust the density.
The cursor moves.
Note
❒ Selecting [Text], [Text / Line Art], or [Text / Photo] for the scan type causes [Auto
Density] to be selected.
❒ You can set the density that is selected right after the machine is turned on or
the {Clear Modes} key is pressed. See “Registering a priority function using a
Reference
p.270 “Registering a priority function using a program”
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Mixing Scan Settings for a Multiple Page Original
When sending an original of several pages, you can select a different density,
resolution, and scan type setting for each page.
1
It is recommended that originals be placed on the exposure glass when mixing
scan settings for a multiple page original.
❖ When placing originals on the exposure glass
A Check which pages you want to scan with different settings.
B Remove the previous page and place the next page that you checked on the
exposure glass.
C Select the density, resolution, and scan type.
You have about 60 seconds (10 seconds for Immediate Transmission) to se-
lect density, resolution, and scan type. The time remaining is shown on the
display.
Adjust the settings for each page before you press the {Start} key.
❖ When placing originals in the Auto Document Feeder (ADF)
A Check which pages you want to scan with different settings.
B Select the density, resolution, and scan type before the page you want to
change the settings for starts being scanned.
Depending on what time the scan settings are adjusted, the settings may
not be reflected in the resulting operation.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Line Port
Changing the Line Port
Select a line port or protocol to be used for standard fax or IP-Fax transmission.
When the extra G3 interface unit is installed, you can connect to a maximum of
three ports.
1
Important
❒ To add more fax lines, the optional extra G3 interface unit is required.
❖ G3
G3 is selected after power up or when the machine is reset. If you install the
extra G3 interface unit, you can select “G3-1”, “G3-2”, “G3-3”, or “G3 Au-
to”depending on the number of the installed unit.
❖ Multi-port
When the extra G3 interface unit is installed, communications can take place
simultaneously through three lines at once.
The following list shows protocol combinations available for each line type.
Option
Available line types
PSTN
Available protocol combinations
Without option
Extra G3 interface unit
G3
PSTN n PSTN
G3 n G3
Extra G3 interface unit n PSTN n PSTN n PSTN G3 n G3 n G3
Extra G3 interface unit
❖ IP-Fax
When sending an IP-Fax, select either “SIP” or “H.323” as the protocol.
To display “SIP” and “H.323” on the screen, make the settings in “Initial Set-
tings” in the Facsimile Features menu.
Ask your administrator whether you should select “SIP” or “H.323” as the
protocol.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
A Press [Select Line].
1
B Select the line you want to use.
If you select “G3 Auto”, the machine will use any available line. This increas-
es efficiency.
When one optional extra G3 unit is installed
When two optional extra G3 units are installed
When H.323/SIP are set to “On”
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Line Port
C Press [OK].
The standby display appears.
Note
❒ When you install the extra G3 interface unit, you can specify the line port
1
home position. See “Registering a priority function using a program”.
❒ When sending a fax, you can select the line port if dialing with the number
keys.
❒ A maximum of three simultaneous communications are possible. You can-
not perform three Immediate Transmissions simultaneously.
❒ If three communications are in progress, the display shows the first com-
Reference
p.270 “Registering a priority function using a program”
“Facsimile Features”, General Settings Guide
Simultaneous Broadcast Using Multiple Line Ports
The Standard Broadcast function sends faxes one at a time to multiple destina-
tions in the order of specified destinations.
However, the Simultaneous Broadcast function can simultaneously send faxes
to multiple destinations using different lines.
This results in a shorter overall transmission time.
Important
❒ The optional extra G3 interface unit is required.
Note
❒ A maximum of three simultaneous transmissions (including LAN) are possi-
ble.
❒ When using the optional extra G3 interface unit, if you set the line selection
as “G3 Auto” beforehand, the machine will use whichever G3 line is not busy.
This increases efficiency.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Specifying a Destination
This section explains how to specify a destination.
Fax numbers, IP-Fax destinations, and e-mail addresses can be specified.
1
Note
❒ The display shows the percentage of free memory space for storing originals.
Since fax numbers, IP-Fax destinations and e-mail addresses are programmed
in separate memory, dialing fax numbers using the number keys does not
change the percentage on the display.
Sending Over a Fax Line
Enter numbers directly using the number keys on the right side of the control
panel.
A Make sure that [Fax] is selected.
B Enter the fax number using the number keys.
If you make a mistake, press the {Clear/Stop} key, and then enter again.
If the optional extra G3 interface unit is installed, select G3 before pressing the
{Start} key.
To select a destination from the Address Book, see “Using the Address Book
to Specify Destinations”.
C Press the {Start} key.
The machine starts to scan the original and stores it in memory. When scan-
ning ends, the Communicating indicator lights and transmission starts.
Note
❒ You can insert pauses and tones in a fax number.
❒ Press [Prg. Dest.] after entering the fax number to store the fax number in
the destination list.
❒ For the maximum number of digits for a destination, see “Maximum Val-
ues”.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifying a Destination
p.65 “Entering a pause”
p.66 “Entering a tone”
1
p.76 “Using the Address Book to Specify Destinations”
p.83 “Registering Entered Destinations to the Address Book”
p.278 “Maximum Values”
Entering a pause
Press [Pause] when dialing or storing a number to insert a pause of about two
seconds.
Note
❒ A pause is shown as a “-” on the display.
❒ You can also program numbers including pauses in the destination list.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Entering a tone
This function allows a machine connected to a pulse dialing line to send tonal
signals (for example if you want to use a special service on a tone dialing line).
When you press [Tone], the machine dials the number using tonal signals.
1
This section explains how to use the tone function with On Hook Dial as an ex-
ample.
A Press [On Hook].
B Enter the fax number using the number keys.
C Press [Tone].
D Enter the number you want to tone dial using the number keys.
E Press the {Start} key.
The machine starts to scan the original and stores it in memory. When scan-
ning ends, the Communicating indicator lights and transmission starts.
Note
❒ Certain services may be unavailable even when using Tone function.
❒ A tone is shown as a “T” on the display and the next numbers are dialed
using tonal signals.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifying a Destination
Sending by IP-Fax
This section explains how to specify a destination using IP-Fax transmission.
When using IP-Fax transmission, specify the IP-Fax destination (IPv4 address,
host name, or alias telephone number) in place of the fax number.
1
Important
❒ Specify the protocol to be used in [Select Line] in advance.
A Make sure that [Fax] is selected.
B Press [Manual Entry].
C Enter the IP-Fax destination, and then press [OK].
If you enter an incorrect character, press [Backspace] or [Delete All]. Then, re-
enter the characters correctly.
To change the IP-Fax destination after pressing [OK], press [Edit Dest.], re-enter
an IP-Fax destination, and then press [OK].
To select a destination from the Address Book, see “Using the Address Book
to Specify Destinations”.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
D To add a destination, press [Add].
1
When you press [Prg. Dest.], you can register an entered destination in the des-
tination list.
E Specify the next destination.
To add another destination, repeat steps and .
D
E
F Press the {Start} key.
The machine starts to scan the original and stores it in memory. When scan-
ning ends, the Communicating indicator lights and transmission starts.
Note
❒ Depending on security settings, [Manual Entry] may not appear, and you
may be unable to enter the IP-Fax destination.
❒ For a list of gateways (T.38-compliant), gatekeepers, or SIP servers that are
certified as operable with this machine, contact your local reseller or ser-
vice representative.
❒ Methods of entering a destination vary depending on the network settings
made by the administrator. Ask the machine administrator for details. For
details about entering the IP-Fax destination, see “Regarding IP-Fax desti-
nations”.
❒ To avoid accidentally pressing the wrong Destination key, you can set the
machine so that each time a destination is added using a Destination key,
[
Add] must be pressed. Make the setting in User Parameters (switch 17, bit 2)
in the Facsimile Features menu.
❒
For the maximum number of digits for a destination, see “Maximum Values”.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifying a Destination
p.76 “Using the Address Book to Specify Destinations”
1
p.83 “Registering Entered Destinations to the Address Book”
p.278 “Maximum Values”
“Entering Text”, About This Machine
“Facsimile Features”, General Settings Guide
Regarding IP-Fax destinations
Depending on the network to which this machine is connected or this machine's
configuration, enter the IP-Fax destination as follows:
❖ When not using a gatekeeper/SIP server
• From IP-Fax to IP-Fax
Specify the IPv4 address or host name of the receiving machine.
Example: 192.168.1.10 (IPv4 address)
Example: IPFAX1 (host name)
• From IP-Fax to G3 fax
Specify the G3 fax telephone number of the receiving machine.
Example: 0312345678
❖ When using a gatekeeper server
• From IP-Fax to IP-Fax
Specify the alias telephone number of the receiving machine.
Example: 0311119999 (alias telephone number)
• From IP-Fax to G3 fax
Specify the G3 fax telephone number of the receiving machine.
Example: 0312345678
❖ When using a SIP server
• From IP-Fax to IP-Fax
Specify the SIP user name of the receiving machine.
Example: ABC (SIP user name)
• From IP-Fax to G3 fax
Specify the G3 fax telephone number of the receiving machine.
Example: 0312345678
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Note
❒ To send to a G3 fax via a gateway connected to a public telephone line, you
must specify the receiver's machine telephone number. For example, if the re-
ceiver's fax number is “0312345678”, specify “5678”. To send from an IP-Fax
to G3 fax without using gatekeeper or SIP server, you must register the gate-
way also.
1
❒ When you specify a destination with IP-Fax, depending on the receiver's net-
work configuration, you may need to specify the IPv4 address and port num-
ber of the receiving machine. For example, if the receiver's IPv4 address is
“192.168.1.10” and the port number is “2100”, specify “192.168.1.10:2100”.
Ask the network administrator for details.
❒ When you specify a host name, depending on the receiver's network config-
uration, you may need to specify the host name and port number of the re-
ceiving machine. For example, if the receiver's host name is “IPFAX1”and the
port number is “2100”, specify “IPFAX1:2100”. Ask the network administra-
tor for details.
❒ An alias telephone number is a number that is registered in the gatekeeper,
and is available only in the network to which the gatekeeper is connected.
❒ Pay attention to the number of telephone number digits set in the gate-
way/IPv4 address conversion table to avoid transmission error.
Sending to an E-mail Address
This section explains how to specify an e-mail address as a destination.
When using Internet Fax transmission, specify the e-mail address in place of the
fax number.
Important
❒ In the destination list, register senders, specify their e-mail addresses, and set
the User Name as [Sender] in advance.
❒ Internet Fax is executed in only Memory Transmission that starts transmis-
sion automatically after storing documents in memory. If you switch the type
of transmission to Internet Fax while the machine is in the Immediate Trans-
mission mode, the transmission mode is automatically switched to the Mem-
ory Transmission mode.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifying a Destination
A Press [Internet Fax] to switch the type of transmission to Internet Fax.
1
B Specify the sender.
For details about specifying senders, see “Sender Settings”.
C Press [Manual Entry].
D Enter the e-mail address destination, and then press [OK].
If you enter an incorrect character, press [Backspace] or [Delete All]. Then, re-
enter the characters correctly.
To change the e-mail address after pressing [OK], press [Edit Dest.], re-enter an
e-mail address, and then press [OK].
To select a destination from the Address Book, see “Using the Address Book
to Specify Destinations”.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
E To add a destination, press [Add].
1
When you press [Prg. Dest.], you can register an entered destination in the des-
tination list.
F Specify the next destination.
To add another destination, repeat steps and .
E
F
G Press the {Start} key.
The machine starts to scan the original and stores it in memory. When scan-
ning ends, the Communicating indicator lights and transmission starts.
Note
❒ Depending on security settings, [Manual Entry] may not appear, and you
may be unable to enter the e-mail address.
❒ For details about canceling a transmission, see “Canceling a Transmis-
sion”.
❒ To avoid accidentally pressing the wrong Destination key, you can set the
machine so that each time a destination is added using a Destination key,
[Add] must be pressed. Make the setting in User Parameters (switch 17, bit
2) in the Facsimile Features menu.
❒
For the maximum number of digits for a destination, see “Maximum Values”.
❒ If “Auto Specify Sender Name” is set to “On” in “System Settings”, the
sender is automatically specified and you can omit the procedure for spec-
ifying a sender. If “On” is selected, the specified e-mail address is printed
at “From:”. If no e-mail address is specified for the sender, or if the speci-
fied e-mail address is not programmed in the destination list, Internet Fax
documents cannot be sent.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifying a Destination
p.101 “Sender Settings”
1
p.114 “Canceling a Transmission”
p.278 “Maximum Values”
“Entering Text”, About This Machine
“System Settings”, General Settings Guide
“Facsimile Features”, General Settings Guide
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gen-
eral Settings Guide
Bypassing the SMTP server
You can send Internet Fax documents directly to their destinations without go-
ing through the SMTP server.
Important
❒ To use this function, the following settings must be made. For details about
these settings, see “System Settings”, General Settings Guide and “Special
Operations under Windows”, Network Guide.
• In “System Settings”, “SMTP” in “E-mail Communication Port”, set the
port number to “25”.
• To specify the host name of the other party as the domain part of the e-mail
address, program the host name of the other party on the DNS server.
❒ If the other party's IPv4 address is not registered on the DNS server, specify
the IPv4 address at the domain part of the e-mail address.
❒ To use this function, the other party's fax machine must be:
• compatible with Internet Fax
• connected to the same LAN as this machine
• have its reception protocol set to SMTP
❒ SMTP authentication set on the other party's fax machine is disabled when In-
ternet Fax is transmitted using this function.
❒
If an Internet Fax is transmitted from the other party using this function, even
if reception is not successful, an Error Mail Notification is not sent to the sender.
❒ When an Internet Fax is transmitted using this function, even if transmission
is not successful, the error e-mail is not sent from the server.
❒ When using this function, you cannot send Internet Fax documents to the ad-
ministrator's e-mail address programmed on this machine.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
You can send Internet Fax documents directly to their destinations without go-
ing through the SMTP server. Internet Faxes are normally transmitted via the
SMTP server. However, with this feature the domain part of the destination's e-
mail address is read as the SMTP server's address and transmissions bypass the
SMTP server. Since this reduces load on the server, you can send faxes without
having to take server to destination transfer time into account.
1
There are two ways of specifying a destination, as follows:
❖ Specify the other party's host name
Specify a destination's e-mail address by adding the other party's host name
to the domain part of the e-mail address. Specify the address to the right of @
as follows: “host name”, “. (dot)”, and “domain name”.
xxxx@host name of the other party.domain name
Example: The other party's e-mail address is “[email protected]” and the
host name is “HOST”; [email protected]
❖ Specify the other party's IPv4 address
Specify a destination's e-mail address by changing the domain part of the e-
mail address to the other party's IPv4 address.
xxxx@[the other party's IPv4 address]
Example: The other party's e-mail address is “[email protected]” and the
IPv4 address is “192.168.1.10”; abc@[192.168.1.10]
Follow these steps to bypass the SMTP server.
A Press [SMTP].
B Press [No].
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifying a Destination
C Press [OK].
1
Note
❒ When you specify destinations directly using the number keys, you can
specify whether or not to use the SMTP server for each destination.
❒ When you select destinations in the destination list, the SMTP server set-
ting specified in the Address Book is enabled.
❒ To send Internet Fax documents from a computer, use the LAN-Fax Driver
to specify whether or not to bypass the SMTP server. When sending with
the [Use device address] check box selected, the SMTP server setting speci-
Reference
p.239 “Sending Fax Documents from Computers”
“System Settings”, General Settings Guide
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gen-
eral Settings Guide
“Special Operations under Windows”, Network Guide
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Using the Address Book to Specify Destinations
When destinations are programmed in a destination list, you can specify a des-
tination by selecting a Destination key from the destination list.
1
The programmed name appears on Destination key.
Press [Fax] or [Internet Fax] to switch the transmission type between fax/IP-Fax
and Internet Fax.
Important
❒ In the destination list, program an individual fax number, IP-Fax destination,
e-mail address and/or groups of destinations.
A Press [Fax] or [Internet Fax] to switch the transmission type to fax/IP-Fax or
Internet Fax.
B Press the title word key where the desired destination is programmed.
For example, if you want to specify “NEW YORK OFFICE” programmed in
“LMN”, press [LMN].
C Press the Destination key programmed with the desired destination.
If the desired Destination key is not shown, press [U] and [T] to look through
the list.
press the {Clear / Stop} key to cancel the selection.
To select more destinations, repeat steps and .
B
C
The destination is set and the Destination key is highlighted.
D Press the {Start} key.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifying a Destination
Note
❒ To check the contents of Destination keys, print the destination list.
Reference
“System Settings”, General Settings Guide
1
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gen-
eral Settings Guide
Switching the titles in the Address Book
There are three types of titles for destination lists; “Title 1”, “Title 2”, and “Title
3”. The above display shows “Title 1”.
A Press [Change Title].
B Select the type of the title, and then press [OK].
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Specifying Group Destinations
If you program multiple destinations into a Group, you can send documents to
all destinations in that Group using just a few keystrokes. Destinations pro-
1
grammed in a group are indicated by
.
Important
❒ In the destination list, program an individual fax number, IP-Fax destination,
e-mail address and/or groups of destinations.
❒ Group destination can be used only for Memory Transmission; it cannot be
used for Immediate Transmission. The machine automatically changes to
Memory Transmission when you use group destination.
❒ The total number of destinations programmed in multiple groups should not
exceed the maximum number of destinations you can specify for one file. For
details, see “Maximum Values”.
A Press [Fax] or [Internet Fax] to switch the transmission type to fax/IP-Fax or
Internet Fax.
B Press the Destination key programmed with the desired group.
The destination is set and the Destination key is highlighted.
To select more groups, repeat step .
B
C Press the {Start} key.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifying a Destination
Note
❒ Destinations programmed in groups can be checked using “Print Group
Dial List” in “System Settings”.
❒ If a destination where a fax number, e-mail address, or IP-Fax destination
is not programmed is included in the specified group, the confirmation
message appears. Press [Select] to specify destinations where the fax num-
ber, the e-mail address, or IP-Fax destination is programmed. Press [Can-
cel] to change the destination. You can select the priority order used to
specify an alternative destination if there is no destination of the specified
type. Make this setting with User Parameters (switch 32, bit 0) in the Fac-
simile Features menu.
1
❒ To cancel any destination(s) among the group, press [Expand Group Dest.] in
[Check Modes]. Then, on the standby display, press [U] and [T] to display
the desired destination, and then press the {Clear/Stop} key. You can also
cancel a transmission by pressing the highlighted Destination key to dese-
lect it.
Reference
p.278 “Maximum Values”
“System Settings”, General Settings Guide
“Facsimile Features”, General Settings Guide
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gen-
eral Settings Guide
Selecting Destinations from Recent Destinations
The machine stores the latest destinations specified for each transmission meth-
od. This function saves time when you are sending to the same destination re-
peatedly, as you do not have to enter the destination again.
Important
❒ The following kinds of destinations are not stored:
• Destinations specified using the destination list
• Destinations specified as a group destination
• Destinations dialed using the optional handset or an external telephone
• Destinations selected from Recent Destinations (regarded as already
stored in memory)
• Second and later destinations broadcasted to
• Destinations specified in the LAN-Fax Driver on the computer
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
A Place the original, and then select the scan settings you require.
B Press [Recent].
1
C Select the destination you want to redial to, and then press [OK].
D Press the {Start} key.
Note
❒ You can select Internet Fax and IP-Fax destinations from Recent Destina-
tions as well.
❒ When you press [Program Dest.], you can register a selected recipient in the
destination list.
❒ For the maximum number of recent destinations the machine can store, see
“Maximum Values”.
p.83 “Registering Entered Destinations to the Address Book”
p.278 “Maximum Values”
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Destinations in the Address Book
Programming Destinations in the Address
Book
1
You can program fax numbers, e-mail addresses, IP-Fax destinations, and folder
destinations using Address Book Management in Administrator Tools in the
System Settings menu.
A Press the {User Tools/Counter} key.
ALV020S
B Press [System Settings].
C Press [Administrator Tools].
D Press [Address Book Management].
E Check that [Program / Change] is selected.
F Press [New Program].
For a description of the subsequent procedure, see “System Settings”, General
Settings Guide.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Note
❒ You can also register programmed fax numbers, e-mail addresses, IP-Fax
destinations, and folder destinations in a Group.
❒ When you press the {Facsimile} key to show the facsimile initial display af-
ter changing the contents of the Address Book, the “Destination list /
machine settings are updated.” message appears. Press [Exit] to bring
up the facsimile's initial display.
1
❒ You can register in the Address Book using Web Image Monitor or Smart-
DeviceMonitor for Admin. For details about installation, see “Monitoring
and Configuring the Printer”, Network Guide, or, for information about
the Address Book, see the relevant Help.
Reference
“System Settings”, General Settings Guide
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gen-
eral Settings Guide
“Monitoring and Configuring the Printer”, Network Guide
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Destinations in the Address Book
Registering Entered Destinations to the Address Book
This section explains how to register a directly entered fax number, e-mail ad-
dress, or IP-Fax destination to the Address Book.
1
When registering a destination directly entered or displayed on the Recent Des-
tination screen in the Address Book, [Prg. Dest.] appears in the destination field.
A Press [Prg. Dest.].
B Press [Names] and enter any necessary information.
For details about registering destinations, see “Registering Addresses and
Users for Facsimile/Scanner Functions”, General Settings Guide.
C Press [OK].
Note
❒ Depending on security settings, [Prg. Dest.] may not appear, and you may
be unable to register the destination.
❒ When you press the {Facsimile} key after changing the contents of the Ad-
dress Book, the “Destination list / machine settings are updat-
Reference
p.79 “Selecting Destinations from Recent Destinations”
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gen-
eral Settings Guide
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Searching for a Destination in the Address
Book
1
Use this function to search for a destination registered in the destination list or
on the LDAP server.
Important
❒ To search for a destination from an LDAP server, the LDAP server must be
registered in advance. For details about registering LDAP servers, see “Sys-
tem Settings”, General Settings Guide.
Note
❒ Press [Fax] or [Internet Fax] on the Search Destination screen to switch the
transmission type between fax/IP-Fax and Internet Fax.
❒ The search returns only destinations that partially match the entered name.
❒ A warning message appears if the search returns more than the maximum
number of destinations you can search for at a time. Press [Exit] and change
the destination name to view fewer destinations.
❒ Although one user can program multiple e-mail addresses, only one address
can be retrieved by the search. The address retrieved by the search depends
on the searching method supported by the LDAP server. However, the ad-
Reference
p.278 “Maximum Values”
“System Settings”, General Settings Guide
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching for a Destination in the Address Book
Search by Destination Name
Follow these steps to search for a destination registered in the Address Book by
name.
1
A Press [Search Dest.].
B Select a search destination.
To search through the Address Book, select [Address Book].
To search through an LDAP server, select the relevant LDAP server.
C Press [Fax] or [Internet Fax] to switch the transmission type to fax/IP-Fax or
Internet Fax.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
D Press [Name].
1
E Enter the destination name you want to search for, and then press [OK].
If you enter a wrong destination name, press [←], [→], [Backspace], and [Delete
All], and then enter the destination name again.
F Confirm the characters you entered, and then press [Start Search].
A search-in-progress message appears.
When the search is finished, a result appears.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching for a Destination in the Address Book
G Select a destination.
1
If the desired destination does not appear, use [U] or [T] to scroll through the
list.
Press [Details] to display the detailed information of the selected destination.
Reference
“Entering Text”, About This Machine
Search by Fax Number/IP-Fax Destination
Follow these steps to search for a destination registered in the Address Book by
fax number or IP-Fax destination.
A Press [Search Dest.].
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
B Select a search destination.
To search through the Address Book, select [Address Book].
To search through an LDAP server, select the relevant LDAP server.
1
C Press [Fax Destination].
D Enter the number you want to search for, and then press [OK].
To search for an IP-Fax destination, enter the IP-Fax destination that you want
to find.
If you enter a wrong number, press [←], [→], [Backspace], or [Delete All], and
then enter the number again.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching for a Destination in the Address Book
E Confirm the entered fax numbers, and then press [Start Search].
1
A search-in-progress message appears.
When the search is finished, a result appears.
F Select a destination.
If the desired destination does not appear, use [U] or [T] to scroll through the
list.
Press [Details] to display the detailed information of the selected destination.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Search by E-mail Address
Follow these steps to use an e-mail address to search for a destination registered
in the destination list.
1
A Press [Search Dest.].
B Select a search destination.
To search through the Address Book, select [Address Book].
To search through an LDAP server, select the relevant LDAP server.
C Press [Internet Fax] to switch the type of transmission to Internet Fax.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching for a Destination in the Address Book
D Press [E-mail Address].
1
E Enter the e-mail address you want to search for, and then press [OK].
If you enter a wrong e-mail address, press [←], [→], [Backspace], or [Delete All],
and then enter the e-mail address again.
F Confirm the entered characters, and then press [Start Search].
A search-in-progress message appears.
When the search is finished, a result appears.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
G Select a destination.
1
If the desired destination does not appear, use [U] or [T] to scroll through the
list.
Press [Details] to display the detailed information of the selected destination.
Search Using Advanced Search
Follow these steps to search for a destination registered in the Address Book by
specifying search criteria.
A Press [Search Dest.].
B Select a search destination.
To search through the Address Book, select [Address Book].
To search through an LDAP server, select the relevant LDAP server.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching for a Destination in the Address Book
C Press [Advanced Search].
1
D Press the key for each condition, and then enter a partial string.
The following conditions can be specified for Address Book searches: Name,
User Code, Fax Destination, E-mail Address, and Folder Name.
The following conditions can be specified for LDAP server searches: Name,
Fax Destination, E-mail Address, Company Name, and Department Name.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
E Select search criteria for each condition.
1
The meanings of the search criteria are as follows:
• [Beginning Word]: Search for strings that start with the specified character.
Example: When searching for “ABC”, enter “A”.
• [End Word]: Search for strings that end with the specified character.
Example: When searching for “ABC”, enter “C”.
• [Exact Match]: Search for strings that fully match the specified character.
Example: When searching for “ABC”, enter “ABC”.
• [Include one Word]: Search for strings that include the specified character.
Example: When searching for “ABC”, enter “A”, “B”, or “C”.
• [Exclude Words]: Search for strings that do not include the specified charac-
ter.
Example: When searching for “ABC”, enter “D”.
• [Fuzzy Search]: Perform a fuzzy search.
This item appears when selecting an LDAP server in step . The perfor-
B
mance of fuzzy search depends on the search method supported by the
LDAP server.
F Press [OK].
G Press [Start Search].
When the search is finished, the search result appears.
H Select a destination.
If the required destination does not appear, press [U] or [T] to display it.
Press [Details] to display the detailed information of the selected destination.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching for a Destination in the Address Book
Note
❒ You can add one additional search condition for LDAP servers by specify-
ing the Search Options under Program / Change / Delete LDAP Server
under System Settings. For details about setting Search Options, see “Sys-
tem Settings”, General Settings Guide.
1
❒ The string you enter in the [Name] condition field is read as the first or last
name, depending on the administrator's setting. For example, to search for
the name “John Smith”, ask the system administrator whether you should
enter “John” or “Smith”.
Reference
“Entering Text”, About This Machine
“System Settings”, General Settings Guide
Search by Registration Number
Follow these steps to search for a destination by specifying a registration num-
ber stored in the destination list.
A Press [Fax] or [Internet Fax] to switch the transmission type to fax/IP-Fax or
Internet Fax.
B Press [Reg. No.].
The registration number entry display appears.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
C Enter a registration number using the number keys, and then press [#].
1
You do not need to enter the first zeros of a registration number when the dis-
play prompts you to enter five digits.
If you make a mistake, press [Clear], and then try again.
D Press [OK].
The corresponding destination appears.
Note
❒ If the “Cannot find the specified Registration No.” message ap-
pears, the specified registration number or selected type of transmission is
wrong or does not exist. Press [Exit], check the registration number again,
and then follow the procedure from step .
B
96
Download from Www.Somanuals.com. All Manuals Search And Download.
On Hook Dial
On Hook Dial
The On Hook Dial function allows you to dial while listening to the tone from
the internal speaker. You can send a fax checking the connection.
1
Important
❒ This function is not available for the optional extra G3 interface unit, Internet
Fax and IP-Fax.
A Place the original, and then select the scan settings you require.
B Press [On Hook].
You will hear a low tone from the internal speaker.
If you want to cancel this operation, press [On Hook] again.
C Dial.
The machine immediately dials the destination.
If you make a mistake, press [On Hook] or the {Clear Modes} key, and then try
again.
To select a destination from the Address Book, see “Using the Address Book
to Specify Destinations”.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
D {WShtaertn} tkheey.line is connected and you hear a high-pitched tone, press the
The transmission starts.
If you want to cancel a transmission, press the {Clear/Stop} key, and then re-
1
move the originals.
After transmission, the standby display appears.
Note
❒ This function is unavailable in some countries.
❒ Press [Vol...] to display the Adjust Sound Volume screen, and then press
[Louder] or [Lower] to adjust the volume of the on-hook sound. The volume
can also be preprogrammed in the Facsimile Features menu.
❒ If you have the optional handset or an external telephone on the fax ma-
chine, you can speak with the other party when you hear a voice. If you
hear a voice before pressing the {Start} key, pick up the optional handset
or the handset of the external telephone and tell the receiver you want to
send a fax document (ask them to switch to facsimile mode).
❒ For details about On Hook Mode Release Time, see “Facsimile Features”,
General Settings Guide.
Reference
p.76 “Using the Address Book to Specify Destinations”
“Facsimile Features”, General Settings Guide
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Dial
Manual Dial
Pick up the optional handset or the handset of the external telephone and dial.
When the line is connected and you hear a high-pitched tone, press the {Start}
key to send your fax document. If, on the other hand, you hear a voice at the oth-
er end, continue conversation as normal.
1
Important
❒ The optional handset or an external telephone is required.
❒ This function is not available for the optional extra G3 interface unit, Internet
Fax and IP-Fax.
❒ If Immediate TX Result Report (Immediate Transmission) is printed, the re-
sult of a transmission with Manual Dial is not mentioned in the report.
A Place the original, and then select the scan settings you require.
B Pick up the handset.
You will hear a dial tone.
C Dial.
The machine immediately dials the destination.
If you make a mistake, replace the handset, and then try again from step .
B
To select a destination from the Address Book, see “Using the Address Book
to Specify Destinations”.
D W{Shtaertn} tkheeyltionseeinsdcyoonunrecfatexddoancudmyeonut.hear a high-pitched tone, press the
If you hear a voice, tell the receiver that you want to send them a fax docu-
ment (ask them to switch to facsimile mode).
The transmission starts.
E Replace the handset.
If you want to cancel a transmission, press the {Clear/Stop} key, and then re-
move the originals.
After transmission, the standby display appears.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Note
❒ When the operation switch is off, even if the main power switch is on, you
cannot operate this machine using only the handset of the external tele-
1
Reference
p.76 “Using the Address Book to Specify Destinations”
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Sender Settings
Sender Settings
Use this function to set sender information.
If the sender's e-mail address is registered in the destination list, the sender can
receive transmission results by e-mail.
1
Also, if you enable the Stamp Sender Name, the registered sender's name (user
name) appears on the receiver's sheet, lists, and report.
Important
❒ In the destination list, register senders, specify their e-mail addresses, and set
the User Name as [Sender] in advance.
❒ If user authentication is set, the user logged in is set as sender. The transmis-
sion result is sent to the logged-in user's e-mail address.
A Place the original, and then select the scan settings you require.
B Press [Sender Name].
C Select a sender.
To select a sender by specifying the registration number registered in the Ad-
dress Book, press [Registration No.].
To search for a sender from the Address Book, press [Search].
If a destination protection code is set, the entry screen appears. Enter the pro-
tection code for destination using the number keys, and then press [OK].
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
D Confirm the selected sender, and then press [OK].
1
E To print the sender's name on the receiver's sheet, press [Stamp Sender Name]
to highlight it.
If you enable this function, the sender's name (user name) appears on the re-
ceiver's sheet, lists, and report.
F To confirm the transmission results by e-mail notification, press [E-mail TX
Results] to highlight it.
If the sender's e-mail address is registered, you can send the transmission re-
sult to the registered e-mail address.
G Press [OK].
The standby display appears.
To check the settings, press [Sender Name].
H Specify the destination, and then press the {Start} key.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Sender Settings
Note
❒ You can confirm transmission results by using both the E-mail TX Results
function, which sends the results by e-mail, and the Communication Re-
sult Report printed by the machine. You can set whether to use both of
these together in User Parameters (switch 10, bit 6) in the Facsimile Fea-
tures menu.
1
❒ You can use Communication Result Report, etc. to check usage status by
specified users. If user authentication is set, you can check usage by
logged-in users. If User Code is set to sender, you can count the number of
uses by each user.
❒ To cancel the Sender Name, cancel the transmission. See “Canceling a
Transmission”.
Reference
p.114 “Canceling a Transmission”
“Facsimile Features”, General Settings Guide
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gen-
eral Settings Guide
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
PIN Code Transmission
A PIN (Personal Identification Number) Code is a number used for identifying
the sender.
1
PIN Code Transmission uses the PABX (Private Automatic Branch eXchange)
system to prevent unauthorized users sending faxes and to manage charges ac-
cording to user.
A PIN Code is added to the end of the fax number, and this is identified by the
PABX. The PIN Code cannot be revealed or leaked over public telephone lines.
To utilize PIN Codes, your PABX must be equipped with the PIN Code function.
Depending on the PABX system you are using, you might have to enter a PIN
Code every time you want to send a fax.
If you want to use PIN Code Transmission, ask the PABX administrator if the
PABX you are connected to supports the PIN Code function, and if it does, con-
tact your service representative for information about setting up.
Important
❒ Program the PIN Code TX function to a Quick Operation key beforehand.
❒ This function is not available with IP-Fax and Internet Fax.
❒ When you specify a group destination, a PIN Code is added only to those fax
destinations included in the group.
A Place the original, and then select the scan settings you require.
B Specify the fax number of a destination.
C Press [PIN Code TX].
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Sender Settings
D Enter the PIN Code, and then press [OK].
1
The standby display appears.
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
E Press the {Start} key.
Note
❒ For the maximum number of digits you can use in a PIN Code, see “Max-
imum Values”.
❒ You can enter numbers, p, q, and pauses.
❒ PIN Codes are not printed in lists and reports.
❒ You can set the machine so that a PIN Code must be entered after the fax
number before you can send a fax. For details, contact your service repre-
sentative.
Reference
p.278 “Maximum Values”
“Facsimile Features”, General Settings Guide
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Advanced Features
This section describes how to specify a destination using advanced features.
1
Setting SUB Codes for Transmission
Follow these steps to send a document with a SUB Code as a confidential trans-
mission.
A SUB Code is an ID consisting of numbers, q, p, and spaces. Document trans-
mitted with a SUB Code is stored in the other party's memory, and not printed
automatically. The other party inputs the SUB Code to print the received docu-
ment. Privacy can be mutually protected when transmitting a confidential doc-
ument intended for a particular receiver, since only a person who knows the
SUB Code can print the document.
Documents can also be sent via facsimiles that have the Transfer Station func-
tion.
This function helps you save costs when you send the same document to more
than one place in a distant area, and saves time since many documents can be
sent in a single operation.
Important
❒ Documents can be sent to facsimiles that have the Personal Box function.
❒ A SUB Code cannot be used with Internet Fax.
❒ To use this function, set [SUB Code Transmission] to on.
❒ Obtain the SUB Code of the other party in advance.
❒ When sending a confidential document, inform the other party of the SUB
Code in advance.
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
C Press [Option Setting].
1
D Press [SUB Code Transmission].
E Press [OK] twice.
The standby display appears.
F Enter the fax number of a destination or an IP-Fax destination.
G Press [Adv.Features].
H Make sure that [SUB Code] is selected.
I Press [Transmission SUB Code].
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
J Enter a SUB Code, and then press [OK].
1
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
K When a password is required, press [Password (SID)], enter the password
with the number keys, and then press [OK].
L Press [OK].
M Press the {Start} key.
If you use Immediate Transmission and the fax machine at the destination
does not support the SUB Code function, a message will appear on the dis-
play to inform you of this. When this happens, press [Exit] to cancel the trans-
mission.
Note
❒ Make sure the number of digits in the SUB Code matches the specification
of the machine to which you are sending. For the maximum number of dig-
its for the SUB Code of this machine, see “Maximum Values”.
❒ You can store SUB Codes as well as names and fax numbers in the destina-
tion list and Keystroke Programs.
❒ When a SUB Code is stored in the destination list, the SUB Code can be
modified or deleted after selecting a destination using the Destination
keys.
p.141 “SUB Code Transmission”
p.268 “Registering and Changing Keystroke Programs”
p.278 “Maximum Values”
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gen-
eral Settings Guide
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Setting a password
There are times when you may want to use an “SID” (Sender ID) when sending
confidential faxes with the SUB Code function. When you use a Personal Box
that has a password, enter the SID Code as the password.
1
Note
❒ For the maximum number of digits for the SID Code, see “Maximum Values”.
❒ You can enter numbers, p, q, and spaces.
❒ You can store SID Codes as well as names and fax numbers in the destination
list and Keystroke Programs.
p.268 “Registering and Changing Keystroke Programs”
p.278 “Maximum Values”
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gener-
al Settings Guide
Setting SEP Codes for Reception
Follow these steps to enter a SEP Code to request the destination to transmit a
document.
You can receive a document stored in the destination's memory if the document
has the same SEP Code as the SEP Code you entered.
This function enables the machine to utilize services that use the polling function
or receive documents from multiple destinations.
Important
❒ Documents can be received from facsimiles that have Information Boxes and
the SUB Code Transmission function.
❒ A SEP Code cannot be used with Internet Fax.
❒ To use this function, set [SEP Code Reception] to on.
A Press [TX Mode].
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
B Press [Option Setting].
1
C Press [SEP Code Reception].
D Press [OK] twice.
The standby display appears.
E Enter the fax number of a destination or an IP-Fax destination.
F Press [Adv.Features].
G Make sure that [SEP Code] is selected.
H Press [Reception SEP Code].
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
I Enter a SEP Code, and then press [OK].
1
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
J When a password is required, press [Password (PWD)], enter the password
using the number keys, and then press [OK].
K Press [OK].
L Press the {Start} key.
Note
❒ Make sure the number of digits in the SEP Code matches the specification
of the machine from which you are receiving. For the maximum number
of digits for the SEP Code of this machine, see “Maximum Values”.
❒ You can enter numbers, p, q, and spaces.
❒ You can store SEP Codes as well as names and fax numbers in the destina-
tion list and Keystroke Programs.
❒ When a SEP Code is stored in the destination list, the SEP Code can be
modified or deleted after selecting a destination using the Destination
keys.
p.142 “SEP Code Reception”
p.268 “Registering and Changing Keystroke Programs”
p.278 “Maximum Values”
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gen-
eral Settings Guide
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Entering a password
There are times you may want to use a password when receiving faxes by SEP
Code Reception.
1
Note
❒ For the maximum number of digits for the PWD Code, see “Maximum Val-
ues”.
❒ You can enter numbers, p, q, and spaces.
❒ You can store PWD Codes as well as names and fax numbers in the destina-
tion list and Keystroke Programs.
p.268 “Registering and Changing Keystroke Programs”
p.278 “Maximum Values”
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gener-
al Settings Guide
SEP Code RX Reserve Report
This report is printed after SEP Code Reception is set up. You can use this report
to check the reservations for SEP Code Reception.
Note
❒ You can turn this function on or off with the User Parameters (switch 03, bit
3) in the Facsimile Features menu.
❒ You can have a destination displayed with the User Parameters (switch 04, bit
4) in the Facsimile Features menu.
❒ You can display a sender name with the User Parameters (switch 04, bit 5) in
the Facsimile Features menu.
Reference
“Facsimile Features”, General Settings Guide
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
SEP Code RX Result Report
This report is printed after each SEP Code Reception is completed and shows its
result.
1
If E-mail TX Results is programmed in a Quick Operation key, you can select
whether a report e-mail is sent after reception.
Note
❒ You can also check the result of a SEP Code Reception with the Journal.
❒ You can turn this function on or off with the User Parameters (switch 03, bit
4) in the Facsimile Features menu.
❒ To view the report without text disruption, select a font of even character
width in your e-mail application's settings.
❒ You can display a destination with the User Parameters (switch 04, bit 4) in
the Facsimile Features menu.
❒ You can display a sender name with the User Parameters (switch 04, bit 5) in
Reference
p.203 “Journal”
“Facsimile Features”, General Settings Guide
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Canceling a Transmission
This section explains how to cancel a fax transmission.
1
Important
❒ Remember that the Communicating indicator turns off almost immediately
when an Internet fax is being sent.
Before the Original Is Scanned
Use this procedure to cancel a transmission before pressing the {Start} key.
A Press the {Clear Modes} key.
ALV015S
Note
❒ When originals are placed into the ADF, you can cancel transmission sim-
ply by removing them.
While the Original Is Being Scanned
Use this procedure to cancel a transmission while the originals are being
scanned after the {Start} key has been pressed.
A Press the {Clear/Stop} key.
ALV016S
The machine stops scanning.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Canceling a Transmission
Note
Scanning may be completed while you are performing the cancel operation.
❒
While the Original Is Being Transmitted
1
Follow these steps to cancel a transmission while the Communicating indicator
is lit.
A Press the {Clear/Stop} key.
ALV016S
You can also cancel a Memory Transmission by pressing [Change TX / Info].
B Select the file you want to cancel.
If the desired file is not shown, press [U] or [T] to find it.
There are cases when a destination may not be selected as the destination ap-
pears as “p”, depending on the security settings.
C Press [Stop Transmission].
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
D Press [OK].
1
To cancel another file, repeat steps and .
B
D
To cancel stopping transmission, press [Cancel].
E Press [Exit].
The standby display appears.
Note
❒ If you cancel a document while it is being sent, the transmission is halted
as soon as you finish the cancellation procedure. However, some pages of
the document may already have been sent and received at the other end.
❒ If the transmission finishes while you are carrying out this procedure, it
will not be canceled.
❒ If multiple destinations were specified, only one destination number ap-
pears.
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Canceling a Transmission
Before the Transmission Is Started
Use this procedure to cancel a transmission after the original is scanned.
This function is useful to cancel a transmission when you notice a mistake in des-
tination or with the originals after storing. To cancel Memory Transmission,
search for the file to be canceled among the files stored in memory, and then de-
lete it.
1
You can cancel transmission of a file while the file is being sent, stored in mem-
ory, or fails to transmit. All the scanned data is deleted from memory.
Important
❒ This function is unavailable with Immediate Transmission.
A Press [Change TX / Info].
B Press [Check / Stop Transmission File].
The list of stored files being transmitted or waiting for transmission appears.
To display only the files being sent, press [Files under TX].
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
C Select the file you want to cancel.
1
If the desired file is not shown, press [U] or [T] to find it.
There are cases when a destination may not be selected as the destination ap-
pears as “p”, depending on the security settings.
D Press [Stop Transmission].
E Press [OK].
To cancel another file, repeat steps and .
C
E
To cancel stopping transmission, press [Cancel].
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Canceling a Transmission
F Press [Exit] twice.
1
The standby display appears.
Note
❒ To cancel transmission to some destinations that a fax is sent to, see “De-
leting a Destination from a Simultaneous Broadcast”.
❒ If you cancel a transmission while the file is being sent, some pages of your
file may have already been sent and is received at the other end.
❒ If the transmission finishes while you are carrying out this procedure,
transmission cannot be canceled.
❒ If multiple destinations were specified, only the number of destinations for
unsent documents appears.
❒ If multiple destinations were specified, only one destination number ap-
Reference
p.176 “Deleting a Destination from a Simultaneous Broadcast”
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Confirming a Transmission
A Press [Change TX / Info].
1
B Press [Check / Stop Transmission File].
C Select a file to check.
If multiple destinations were specified, only the destination selected first ap-
pears.
If multiple destinations were specified, only the number of destinations for
unsent documents appears.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Confirming a Transmission
D Press [Check / Change Settings].
1
E Confirm a transmission, and then press [Exit].
F Press [Exit] twice.
The standby display appears.
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission
Checking the Storage Result (Memory
Storage Report)
1
This report is printed after an original is stored in memory. It helps you review
the contents and the destinations of stored originals.
Important
❒ If you use Parallel Memory Transmission, the Memory Storage Report is not
printed.
Note
❒ You can turn this report on and off with the User Parameters (switch 03, bit
2) in the Facsimile Features menu.
❒ Even if the machine is set up not to print this report, it is still printed if an orig-
inal could not be stored.
❒ You can select whether to include part of the original image on the report with
the User Parameters (switch 04, bit 7) in the Facsimile Features menu.
❒ You can select whether to display a destination with the User Parameters
(switch 04, bit 4) in the Facsimile Features menu.
❒ You can display a sender name with the User Parameters (switch 04, bit 5) in
the Facsimile Features menu.
Reference
“Facsimile Features”, General Settings Guide
122
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Other Transmission Features
This section explains the features of [TX Mode], which you can use to apply trans-
mission functions.
Sending at a Specific Time (Send Later)
Using this function, you can instruct the machine to delay transmission of your
fax document until a specified later time. This allows you to take advantage of
off-peak telephone charges without having to be by the machine at the time.
Important
❒ If the machine is switched off for about one hour, all fax documents stored in
memory are lost. If documents are lost for this reason, a Power Failure Report
is automatically printed when the operation switch is turned on. Use this re-
port to identify lost documents. For details, see “Troubleshooting When Us-
ing the Facsimile Function”, Troubleshooting.
❒ This function is unavailable with Immediate Transmission. Use Memory
Transmission.
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
C Press [Send Later].
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Transmission Features
D Enter the time using the number keys and select [AM] or [PM]. Then press
[OK].
2
When entering numbers smaller than 10, add a zero at the beginning.
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
To cancel Send Later, press [Cancel]. The display returns to that of step .
C
The specified time is shown above the highlighted [Send Later].
E Press [OK].
The standby display appears.
To check the settings, press [TX Mode].
F Specify a destination, and then press the {Start} key.
Note
❒ You can specify a time within 24 hours of the current time.
❒ If the current time shown is not correct, change it.
❒ You can program one of the Quick Operation keys with operations for this
function. Using the Quick Operation key allows you to omit step .
B
❒ You can cancel the transmission setup for Send Later. See “Canceling a
Transmission”.
Reference
p.114 “Canceling a Transmission”
“System Settings”, General Settings Guide
“Facsimile Features”, General Settings Guide
“Troubleshooting When Using the Facsimile Function”, Troubleshooting
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Requesting a Reception Notice
Requesting a Reception Notice
You can confirm sent documents were properly received using e-mail or the
Journal.
The receiver sends back a reception notice message. Once the reception notice
message is received, “OK” appears in the Result column of the Journal, allowing
the originator to verify the transmission was received.
2
Important
❒ The Reception Notice feature is only available if the receiver supports MDN
(Message Disposition Notification).
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
C Press [Reception Notice] to highlight it.
D Press [OK].
The standby display appears.
To check the settings, press [TX Mode].
E Specify a destination, and then press the {Start} key.
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Transmission Features
Note
❒ If the fax is not received normally, “Error” appears in the Result column.
❒ Only the last 50 communications appear in the Journal. If you do not re-
ceive a reception notice message before the last 50 communications are fin-
ished, “OK” might not be printed in the Journal's Result column. This may
happen even if the mail is received normally at the other end.
❒ If you specify mailing list addresses, do not set for Reception Notice. Oth-
erwise, you will receive multiple reception notice messages from e-mail re-
cipients, and the Result column will be overwritten each time a new notice
message is received. However, if you receive a reception notice message
indicating an error, “Error” appears in the Result column and will not be
overwritten, even if you subsequently receive a reception notice message
as “OK” following the error message.
2
❒ Reception notice results are only shown in the Journal. The Result column
in all other files, lists, and transmission reports show “- -”.
❒ Reception notice messages themselves are not recorded in the Journal.
❒ You can select whether or not to print the Reception Notice. This can be set
with User Parameters (switch 21, bit 0) in the Facsimile Features menu.
❒ You can program one of the Quick Operation keys with operations for this
function. Using the Quick Operation key allows you to omit step .
B
❒ You cannot broadcast e-mail using Reception Notice. The documents are
sent to the destinations in the order in which they were specified.
Reference
“Facsimile Features”, General Settings Guide
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting an E-mail Destination as a BCC
Setting an E-mail Destination as a BCC
E-mail is sent to all specified destinations as bcc.
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
2
C Press [BCC Transmission] to highlight it.
D Press [OK].
The standby display appears.
To check the settings, press [TX Mode].
E Specify a destination, and then press the {Start} key.
Note
❒ You can program one of the Quick Operation keys with operations for this
function. Using the Quick Operation key allows you to omit step .
B
Reference
“Facsimile Features”, General Settings Guide
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Transmission Features
Confirming Transmission Results by E-mail
Use this function to confirm the transmission results by sending an e-mail noti-
fication to the specified destination.
Important
❒ Register the e-mail address of the destination for e-mail notification in the
destination list in advance.
2
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
C Press [E-mail TX Results] to highlight it.
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Confirming Transmission Results by E-mail
D Select the destination of notification, and then press [OK].
2
If you make a mistake, before pressing [OK], press [Clear] or press the selected
Destination key again to turn the highlight off.
[E-mail TX Results] gets highlighted and the destination of notification selected
appears.
E Press [OK].
To check the settings, press [TX Mode].
The standby display appears.
F Specify a destination, and then press the {Start} key.
Note
❒ You can program one of the Quick Operation keys with operations for this
function. Using the Quick Operation key allows you to omit step .
B
Reference
“Facsimile Features”, General Settings Guide
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Transmission Features
Entering the Subject
Allows you to enter a subject for the document you want to send.
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
2
C Press [Subject].
D Enter the subject.
130
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering the Subject
E To enter the character strings programmed in the machine, press [User Text],
and then select the character strings you want to enter.
2
F Press [OK].
The entered subject appears in the Subject field.
G Press [OK].
The standby display appears.
H Specify a destination, and then press the {Start} key.
Note
❒ For convenience, program frequently-used subjects in advance in “Pro-
gram / Change / Delete User Text” in “System Settings”.
❒ If you send e-mail without setting a subject, a subject is automatically in-
serted. For details about how the subject is automatically inserted, see “E-
mail Subject” and “Received Images”.
❒ You cannot send a subject only as e-mail without an original.
❒ You can program one of the Quick Operation keys with operations for this
function. Using the Quick Operation key allows you to omit step .
B
❒ For the maximum number of characters for an e-mail subject, see “Maxi-
mum Values”.
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Transmission Features
p.155 “Received Images”
p.278 “Maximum Values”
“Entering Text”, About This Machine
“System Settings”, General Settings Guide
“Facsimile Features”, General Settings Guide
2
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering the Text
Entering the Text
Allows you to enter the text to be transmitted.
Important
❒ Program text strings in advance in “Program / Change / Delete E-mail Mes-
sage” in “System Settings”.
2
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
C Press [Text].
D Select a text, and then press [OK].
E Press [OK].
The standby display appears.
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Transmission Features
F Specify a destination, and then press the {Start} key.
Note
❒ You cannot send text only without an original.
❒ You can program one of the Quick Operation keys with operations for this
function. Using the Quick Operation key allows you to omit step .
B
Reference
2
“System Settings”, General Settings Guide
“Facsimile Features”, General Settings Guide
134
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission Options
Transmission Options
This section describes various functions that you can switch on and off for any
particular transmission, following the procedures given here.
Standard Message Stamp
2
Use this function to stamp a standard message at the top of the first original sent.
There are four types of standard messages: “Confidential”, “Urgent”, “Please
phone”, and “Copy to corres. section”
You can also program other messages.
Important
❒ While this function is in use, the third line of the Label Insertion is not printed.
❒ When there is an image around the area where the standard message is to be
stamped, that image is deleted.
❒ Program a standard message in “Program / Change / Delete Standard Mes-
sage” in the Facsimile Features menu. See “Facsimile Features”, General Set-
tings Guide.
A Place the originals, and then select the scan settings you require.
B Press [TX Mode].
C Press [Option Setting].
D Press [Standard Message].
135
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Transmission Features
E Select the standard message to be stamped, and then press [OK].
2
The selected standard message is shown above the highlighted [Standard Message].
F Press [OK] twice.
G Specify the destination, and then press the {Start} key.
The machine cannot stamp multiple standard messages.
Note
function. Using the Quick Operation key allows you to omit step and
B
step .
C
Reference
p.138 “Label Insertion”
“Facsimile Features”, General Settings Guide
Auto Reduce
When this function is turned on, if the receiver's paper is smaller than the size of
the original you are sending, the document is automatically reduced to fit onto
the paper available at the other end.
136
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission Options
Important
❒ If you turn this function off, the scale of the original is maintained and some
parts of the image may be deleted when printed at the other end.
2
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
C Select [Option Setting].
D Make sure that [Auto Reduce] is highlighted.
To cancel an Auto Reduce, press [Auto Reduce] to turn the highlight off.
E Press [OK] twice.
F Specify the destination, and then press the {Start} key.
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Transmission Features
Label Insertion
With this function you can have the receiver's name printed on the document
that is received at the other end.
Important
❒ To use this function, set Label Insertion to [On] when registering fax destina-
tions in the Address Book, and also set “Label Insertion” to on when sending
fax documents.
2
❒ When there is an image around the area where the Label is to be printed, that
image is deleted.
The receiver's name is printed as follows:
• Receiver's name: printed at the top of the page and preceded by “To:”.
• Standard message: the programmed message is printed within the next two
lines.
Set this function as follows:
• Set Label Insertion to [On] when programming fax destinations.
• Set Label Insertion to on when sending fax documents.
• On the Standard Message screen, select the standard message you want to
print.
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
C Select [Option Setting].
138
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission Options
D Press [Label Insertion] to highlight it.
2
To cancel Label Insertion, press [Label Insertion] again.
E Press [OK] twice.
F Specify the destination, and then press the {Start} key.
Note
function. Using the Quick Operation key allows you to omit step and
B
step .
C
❒ To print a standard message that is not programmed as a default, program
it in advance in “Program / Change / Delete Standard Message” in the
Facsimile Features menu.
Reference
p.135 “Standard Message Stamp”
“Facsimile Features”, General Settings Guide
139
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Transmission Features
Closed Network
If you turn this function on, transmission will only take place if the destination's
Closed Network Code is the same as yours. This function can stop you acciden-
tally sending information to the wrong place.
Important
❒ You need to register a Closed Network Code beforehand.
2
❒ This function is not available with Internet Fax.
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
C Select [Option Setting].
D Press [Closed Network] to highlight it.
To cancel a Closed Network transmission, press [Closed Network] again.
E Press [OK] twice.
F Specify the destination, and then press the {Start} key.
Note
❒
You can program one of the Quick Operation keys with operations for this
function. Using the Quick Operation key allows you to omit step and step .
B
C
Reference
“Facsimile Features”, General Settings Guide
140
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission Options
SUB Code Transmission
Enable this function to perform SUB Code Transmission.
Important
❒ This function is not available with Internet Fax.
❒ To perform SUB Code Transmission, a SUB Code must be set in [Adv.Features],
the Address Book, or Keystroke Programs in advance. Even though “SUB
Code Transmission” is set to on, if the SUB Code is not appended to the spec-
ified destination, transmission is in standard fax mode.
2
❒ When you select a destination that has a registered SUB Code from the Ad-
dress Book, if “SUB Code Transmission” is set to off, the SUB Code is not ap-
pended and transmission is in standard fax mode.
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
C Select [Option Setting].
D Press [SUB Code Transmission] to highlight it.
To cancel a SUB Code Transmission, press [SUB Code Transmission] again.
E Press [OK] twice.
F Specify the destination, and then press the {Start} key.
141
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Transmission Features
Note
function. Using the Quick Operation key allows you to omit step and
B
step .
C
p.106 “Setting SUB Codes for Transmission”
p.268 “Programs”
2
“Facsimile Features”, General Settings Guide
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gen-
eral Settings Guide
SEP Code Reception
Enable this function to perform SEP Code Reception.
Important
❒ This function is not available with Internet Fax.
❒ To perform SEP Code Reception, a SEP Code must be set in [Adv.Features], the
Address Book, or Keystroke Programs in advance. Otherwise, even if “SEP
Code Reception” is set to on, reception is not performed. If the other party's
fax machine has a polling transmission function, the machine performs poll-
ing reception.
❒ When you select a destination that has a registered SEP Code from the Ad-
dress Book, if “SEP Code Reception” is set to off, the SEP Code is not append-
ed and transmission is in standard fax mode.
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
C Select [Option Setting].
142
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission Options
D Press [SEP Code Reception] to highlight it.
2
To cancel SEP Code Reception, press [SEP Code Reception] again.
E Press [OK] twice.
F Specify the destination, and then press the {Start} key.
Note
function. Using the Quick Operation key allows you to omit step and
B
step .
C
p.109 “Setting SEP Codes for Reception”
p.268 “Programs”
“Facsimile Features”, General Settings Guide
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gen-
eral Settings Guide
143
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Transmission Features
Fax Header Print
When the Fax Header is set to on, the stored name is printed on the receiver's
paper.
You can store two Fax Headers; “First Name” and “Second Name”.
For example, if you store your department name in one and your organization
name in the other, you could use the first when sending internal faxes and the
second for external faxes.
2
Important
❒ In the USA, the Fax Header must contain the telephone number of the line
your machine is connected to. It will be printed on the header of every page
you send. Required in the USA.
A Place the original, and then select the scan settings you require.
B Press [TX Mode].
C Select [Option Setting].
D Make sure that [Fax Header Print] is highlighted.
E Press [OK] twice.
F Specify the destination, and then press the {Start} key.
144
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmission Options
Note
❒ You can program fax header names using the Program Fax Information
function in the Facsimile Features menu.
❒ You can select whether or not dates, fax header names, file numbers, or
page numbers are printed by changing their respective User Parameters
(switch 18, bit 3, 2, 1, 0) in the Facsimile Features menu.
❒ If you used the number keys to specify the receiver, the first header name
is printed on the receiver's paper. To print the second header name, contact
your service representative.
2
function. Using the Quick Operation key allows you to omit step and
B
step .
C
❒ In the USA, law requires that your fax number be included in the Fax
Header. Register the fax number and switch on Fax Header Print with User
Parameters (switch 18, bit 1) in the Facsimile Features menu. See “Facsim-
ile Features”, General Settings Guide.
Reference
“Facsimile Features”, General Settings Guide
145
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Transmission Features
2
146
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Reception
This section explains reception and reception functions such as printing received
documents or routing received documents to other fax machines.
Types of Reception
This section explains different ways of receiving fax documents.
Immediate Reception
Each page of a fax document is printed as soon as it is received. This method is
used for standard fax documents.
Important
❒ When receiving important fax documents, it is recommended that you con-
firm the contents of the received documents with the senders.
❒ The machine may not be able to receive fax documents when free memory
space is low.
❒ If free memory reaches 0% during Immediate Reception, any further recep-
tion becomes impossible and the current communication is terminated.
Note
❒ Normally this machine receives documents by Immediate Reception. But
Memory Reception is used when “Multi-copy Reception” or “2 Sided Print”
is set to on.
❒ If the Substitute Reception is used, a fax document is not printed: it is stored
in memory.
❒ The machine supports Standard, Detail, and Super Fine (with the optional ex-
pansion memory) resolutions. If you do not have the optional expansion
memory, faxes sent at Super Fine resolution is printed on your machine at De-
tail resolution. This may differ from the sender's intended resolution.
147
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
p.49 “Resolution”
p.149 “Substitute Reception”
p.163 “Printing Options”
Memory Reception
The machine waits until all pages of the document have been received into mem-
ory before printing it.
3
Important
❒ About one hour after the machine is turned off, all fax documents stored in
memory are lost. If any documents are lost in this way, a Power Failure Re-
port is automatically printed when the operation switch is turned on. Use this
report to identify lost documents. See “Troubleshooting When Using the Fac-
simile Function”, Troubleshooting.
❒ The machine may not be able to receive large numbers of documents or doc-
uments with high data content. In such cases, it is recommended that you
switch off multi-copy and 2 sided printing, or install the optional expansion
memory.
❒ The machine may not be able to receive fax documents when free memory
space is low.
❒ If free memory reaches 0% during Memory Reception, any further reception
becomes impossible and the current communication is terminated.
Note
❒ Normally this machine receives documents by Immediate Reception. But
Memory Reception is used when “Multi-copy Reception” or “2 Sided Print”
is set to on.
❒ If you have selected Store for Reception File Setting, received document is
saved on the hard disk and will not be printed. You can print those docu-
ments by operating the machine or a connected computer, as necessary.
148
Download from Www.Somanuals.com. All Manuals Search And Download.
Types of Reception
Reference
“Facsimile Features”, General Settings Guide
“Troubleshooting When Using the Facsimile Function”, Troubleshooting
Substitute Reception
Substitute Reception is used when the machine cannot print any fax documents.
In Substitute Reception, a received fax document is stored in memory instead of
being printed. Fax documents received using Substitute Reception are automat-
ically printed when the condition which caused the machine to use Substitute
Reception is rectified.
3
Depending on why the machine cannot print, Substitute Reception might be
used for all fax documents received, or for only those documents that match a
condition specified in the User Parameters in the Facsimile Features menu.
The Receive File indicator lights to let you know when fax documents have been
received using Substitute Reception.
ALV018S
Important
❒ Reception may not take place if there is not enough free memory.
❒ If free memory reaches 0% during Substitute Reception, any further reception
becomes impossible and the current communication is terminated.
Note
❒ When a fax document is received after Store is selected for Reception File Set-
ting in the Facsimile Features menu, the Receive File indicator lights.
❒ The Receive File indicator may light even when receiving documents using
Immediate Reception.
Reference
“Facsimile Features”, General Settings Guide
149
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
Receiving documents unconditionally
If one of the conditions in the following list occurs, the machine receives all fax
documents using Substitute Reception.
Problems
Causes
Solutions
The machine is printing
with a different function.
The machine is busy print- The document is automatically
ing with a different func-
tion.
printed after the current job finishes.
Remove paper from the output tray.
The output tray is full.
The message “Output
Tray is full. Re-
move paper.” appears.
3
h is lit.
The cover is open.
Close the cover shown in the display.
Receiving documents according to parameter-specified settings
If one of the conditions in the following list occurs, the machine receives only
those documents that match the conditions specified in the User Parameters in
the Facsimile Features menu.
Problems
Causes
Solutions
h is lit.
Paper is jammed.
Remove the jammed paper.
For details about removing the pa-
per, see “Clearing Misfeeds”, Trou-
bleshooting.
h is lit.
h is lit.
All trays are out of paper. Add paper.
For details about adding paper, see
“Adding Paper, Toner and Staples”,
Troubleshooting.
Toner is empty.
Replace the toner cartridge.
For details about replacing the toner
cartridge, see “Adding Paper, Toner
and Staples”, Troubleshooting.
All trays are out of action. Call your service representative.
The message “This
tray is out of or-
der.” appears.
150
Download from Www.Somanuals.com. All Manuals Search And Download.
Types of Reception
You can specify the following conditions with the User Parameters (switch 05,
bit 2, 1) in the Facsimile Features menu.
• When Own Name or Own Fax Number is received
The machine switches to Substitute Reception only when the sender has pro-
grammed their Own Name or Own Fax Number. If the power is switched off
for more than an hour, all the documents stored in memory are deleted. In
this case, the Journal can be used to identify the senders of the deleted docu-
ments, so you can ask them to resend.
If a sender has not programmed their Own Name or Own Fax Number, the
machine may fail to receive an important fax document. It is recommended
that you ask important senders to program an Own Name or Own Fax Num-
ber in advance.
3
• Free
The machine switches to Substitute Reception regardless of whether or not
the sender has programmed their Own Name or Own Fax Number.
• Closed Network Code match
The machine switches to Substitute Reception only when the programmed
Closed Network Code of the other end matches the Closed Network Code of
this machine.
• Disable
The machine does not receive any documents.
Reference
“Facsimile Features”, General Settings Guide
“Adding Paper, Toner and Staples”, Troubleshooting
“Clearing Misfeeds”, Troubleshooting
151
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
Reception Modes
There are two ways you can set up the machine to handle incoming calls:
• Manual Reception (the optional handset or an external telephone required)
• Auto Reception
You can change the reception mode only if a standard G3 line is used.
You cannot change the reception mode when a line other than the standard G3
line (G3-2 or G3-3) is used.
Note
3
❒ The optional handset or an external telephone is required to use this machine
as a telephone.
Manual Reception
When a telephone call comes in, the machine rings. If the call is a fax document,
you must switch manually to facsimile mode.
A When the machine rings, pick up the optional handset or the handset of the
external telephone.
B If you hear beeps, press the {Start} key, or hold the {Facsimile} key down for
a few seconds. (The {Start} key is only available in facsimile mode when an
original is not placed.)
C Replace the optional handset or the handset of the external telephone. The
machine will start receiving.
Note
❒ When the operation switch is off, even if the main power switch is on, you
cannot operate this machine using only the handset of the external tele-
phone. You must first press the operation switch to turn on the machine.
Auto Reception
When a telephone call comes in, the machine automatically receives it as a fax
document. Use this setting on a dedicated fax line.
152
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception Modes
Switching the Reception Mode
You can switch reception modes using Reception Settings in the Facsimile Fea-
tures menu.
If you program a Quick Operation key with Switch Reception Mode, you can
switch the reception mode quickly.
A Press [Switch RX Mode].
3
B Select the reception mode, and then press [OK].
To cancel the selection, press [Cancel].
The standby display appears.
Reference
“Facsimile Features”, General Settings Guide
153
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
Receiving Internet Fax Documents
You can receive e-mail documents by Internet Fax.
There are two methods of receiving e-mail: Auto E-mail Reception and Manual
E-mail Reception.
Important
❒ E-mail with attachments other than TIFF-F format files cannot be received.
Senders receive an Error Mail Notification if their e-mail contains attach-
ments. You can select whether or not the machine sends this message with
User Parameters (switch 21, bit 7) in the Facsimile Features menu. However,
TIFF-F documents created by the Saving function of DeskTopBinder can be
received.
3
❒ If [Require Secure Password Authentication (SPA) for all client connections] is select-
ed in Windows Server 2003, reception is not possible.
Note
❒ When Reception Protocol is set to POP3 or IMAP4, you can set the machine
to retain incoming e-mail or delete it from the server in “System Settings”.
❒ With User Parameters (switch 21, bit 1) in the Facsimile Features menu, you
can have the machine send the return receipt in response to the reception no-
tice request attached to the sent e-mail.
Reference
“System Settings”, General Settings Guide
“Facsimile Features”, General Settings Guide
Auto E-mail Reception
When this function is turned on, the machine periodically checks the e-mail
server for incoming e-mail and downloads it as necessary.
Note
❒ If memory runs out, e-mail will not be received at the specified intervals. Re-
ception will resume when sufficient memory becomes available.
❒ E-mail auto-reception should be set in “System Settings”. When you select
auto-reception, set the reception interval in minutes.
Reference
p.155 “Manual E-mail Reception”
“System Settings”, General Settings Guide
154
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving Internet Fax Documents
Manual E-mail Reception
Follow these steps to receive a fax by accessing the e-mail server manually.
Important
❒ Program the Manual E-mail RX function to a Quick Operation key before-
hand.
A Press [Manual E-mail RX].
3
B Check the message, and then press [Exit].
The machine accesses the server to check for e-mail and receives any new e-mail.
The standby display appears.
Reference
“Facsimile Features”, General Settings Guide
Received Images
Here is an example of an Internet Fax document sent from this machine and re-
ceived on a computer using the Outlook Express e-mail application.
The received image varies according to the e-mail application.
Important
❒ When Internet Fax e-mail is sent to computer, the following information is al-
ways inserted in the e-mail text: “This E-mail was sent from “Host
Name” (product name) Queries to: “Administrator's e-mail ad-
dress”” To check the host name and e-mail address, see “System Settings”,
General Settings Guide.
155
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
3
ALV011S
1. E-mail transmitted without speci-
6. Subject
fying a subject in “TX Mode”.
Shows the subject specified in “TX
Mode” at the time of transmission. If no
subject is specified, one is automatically
assigned in the format shown in 1 above.
2. E-mail transmitted with a subject
specified in “TX Mode”.
3. From
7. The message is inserted in all e-
The name (e-mail address) of the sender
mail. “xxxx” is the machine name.
4. Date
8. Attachment File
Any document included by the sender is
displayed as an attached document.
The date and time of e-mail transmission
5. To
The e-mail address of the recipient
Note
❒ The display format of the sender name differs according to that of the Stamp
Sender Name setting and other functions.
❒ The display format of the subject varies according to Stamp Sender Name and
Reference
p.32 “E-mail Subject”
156
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception Functions
Reception Functions
This section explains useful functions for receiving fax documents.
Routing Received Documents
This section describes how to route received documents using SUB Codes.
Important
❒ Documents cannot be routed to folders using this function.
3
Routing received documents with SUB Code
This machine can route received documents using SUB Codes.
When a document is received, its SUB Code is compared to SUB Codes pro-
grammed in Personal Boxes, and if a match is found, the document is routed to
the destination whose SUB Code is specified.
ALT003S
Important
❒ You must set the Personal Box and register a delivery destination beforehand.
Personal Boxes can be programmed in “Box Setting” in the Facsimile Features
menu.
❒ This function is not available when you set received documents to be deliv-
ered to the network delivery server. Delivery of received documents can be
set in “System Settings”.
Note
❒ If the destination specified is an e-mail address, the received document is
routed to that destination as e-mail.
❒
You can route documents received from any fax machine, regardless of manufacturer.
Reference
“System Settings”, General Settings Guide
“Facsimile Features”, General Settings Guide
157
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
Transferring Received Documents
The machine can transfer received documents by using SUB Codes.
Originals sent with a SUB Code that matches the SUB Code programmed as a
Transfer Box are received then relayed to the programmed receiver.
Important
❒ Transfer Boxes and Receiving Stations must be set up in order to transfer re-
ceived documents. Transfer Boxes can be programmed in “Box Setting” in the
Facsimile Features menu.
3
Note
❒ When e-mail addresses are programmed as receivers, received documents
are sent in an e-mail format to the receivers.
❒ Transfer results are not sent back to the requesting party.
❒ You can transfer data received from any fax machine, regardless of manufac-
turer.
Reference
“Facsimile Features”, General Settings Guide
SUB Code Transfer Report
You can check the results of transmission to Receiving Stations. The machine
prints this report when it has finished transmitting to Receiving Stations.
Note
❒ You can select whether the SUB Code Transfer Report be automatically print-
ed using the User Parameters (switch 04, bit 1) in the Facsimile Features
menu.
❒ You can set whether a portion of the original image is printed on the report
with the User Parameters (switch 04, bit 7) in the Facsimile Features menu.
❒ “Unprogrammed” indicates the document could not be sent because the end
receiver is not programmed.
❒ “--” indicates that the Internet Fax document was sent to the mail server pro-
grammed in this machine.
❒ For the maximum number of destinations you can program in a group, see
“Maximum Values”.
Reference
p.278 “Maximum Values”
“Facsimile Features”, General Settings Guide
158
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception Functions
Forwarding Received Documents
This machine can forward received documents to other destinations pro-
grammed in this machine.
3
ALT004S
Note
❒ A fax number, Internet Fax address, IP-Fax destination, or folder address can
be set as a forwarding destination.
❒ If an e-mail address is programmed as the destination, documents received
are forwarded as e-mail.
❒ You need to specify the forwarding destination in advance. Forwarding can
be set under Reception Settings, in the Facsimile Features menu.
❒ If you would like the machine to forward received documents to a particular
destination according to the sender, specify the Forwarding destination for
each sender under Facsimile Features, Reception Settings, Program Special
Sender. Documents from other senders are forwarded to the default Forward-
ing destination specified for this function.
❒ You can select whether the machine prints out the documents it forwards
with User Parameters (switch 11, bit 6) in the Facsimile Features menu.
❒ You can set whether or not the Folder Transfer Result Report is transmitted
to the specified e-mail address if folders are programmed as the forwarding
destinations to which documents are sent from all senders or Special Senders.
For details, see “Facsimile Features”, General Settings Guide.
❒ For the maximum number of destinations you can program in a group, see
“Maximum Values”.
159
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
Reference
p.278 “Maximum Values”
“Facsimile Features”, General Settings Guide
SMTP Reception Using Internet Fax
You can receive a document sent by Internet Fax using SMTP reception.
With SMTP reception, e-mail is received as soon as it is sent to the e-mail address
set by the machine.
3
ALT005S
Important
❒ Set this machine beforehand using the MX record of the DNS server to enable
SMTP reception.
❒ Set the reception protocol to SMTP under “System Settings”.
Note
❒ You can route received e-mail to other Internet Fax machines as well.
❒ Even if SMTP reception is enabled on the DNS server, e-mail sent from the
SMTP server will not be received and the machine reports an error if SMTP
reception is not set. Also, the SMTP server sends an error notification to the
originator.
❒ If an error occurs while receiving e-mail, reception is aborted, the e-mail is de-
leted, and Error Report is printed. Also, the SMTP server will send an error
notification to the originator.
❒ When the SMTP server attempts to route received documents to this machine
while the machine is transmitting e-mail, the machine will respond to the
SMTP server with a “busy” signal. Then, the SMTP server usually tries re-
Reference
p.154 “Auto E-mail Reception”
“System Settings”, General Settings Guide
160
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception Functions
Routing e-mail received via SMTP
E-mail received via SMTP can be routed to other fax machines.
3
ALT006S
Important
❒ Before routing e-mail received via SMTP, you first must set “SMTP RX File
Delivery Settings” to “On” in the Facsimile Features menu.
❒ Depending on security settings, this function may not be available.
The originator can request transfer of e-mail sent to another fax machine by spec-
ifying the e-mail address as follows:
❖ Fax Number
fax=destination fax number@host name of this machine.domain name
Example: to transfer to fax number 212-123-4567:
❖ Single destination programmed in the destination list
fax=qregistration number of 5 digits or less@host name of this machine.do-
main name
Example: to transfer to the destination number 00001:
❖ Group destination programmed in the destination list
fax=qppregistration number of 5 digits or less@host name of this ma-
chine.domain name
Example: to transfer to the destination programmed under Group number
00004:
161
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
Note
❒ If an e-mail transfer request is received when the “SMTP RX File Delivery Set-
tings” is “Off”, this machine responds with an error message to the SMTP
server.
❒ You can make settings that limit transfer to specified originators.
❒ Using this function, you can also send documents from your e-mail applica-
tion to e-mail addresses and G3 fax machines' destinations through this ma-
chine simultaneously.
❒ For the maximum number of destinations you can program in a group, see
“Maximum Values”.
3
Reference
p.278 “Maximum Values”
“Facsimile Features”, General Settings Guide
JBIG Reception
If you use JBIG (Joint Bi-level Image Experts Group) compression, you can send
photographic originals faster than with other methods of compression. It allows
you to receive documents sent in the JBIG format through JBIG Transmission.
Important
❒ You can only use this function with telephone line.
Auto Fax Reception Power-Up
This machine can be set to shut down automatically if no one has used it for a
while. In these situations, even though the operation switch is off, the machine
can still receive incoming documents as long as the main power switch is on.
Important
❒ Reception is not possible if both the operation switch and main power switch
are turned off.
Note
❒ You can set whether documents are printed as soon as they are received (Im-
mediate Reception) with the User Parameters (switch 14, bit 0) in the Facsim-
ile Features menu.
❒ You can also have fax documents received by Memory Reception (Substitute
Reception) printed after the machine is turned on.
Reference
“Facsimile Features”, General Settings Guide
162
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Options
Printing Options
This section explains useful functions for printing received documents.
Print Completion Beep
When this function is turned on, the machine beeps to let you know when a re-
ceived document is printed.
Note
3
❒ You can alter the volume of the beep or turn it off completely using “Adjust
Sound Volume” in the Facsimile Features menu (set the volume to the mini-
mum level).
Reference
“Facsimile Features”, General Settings Guide
Checkered Mark
When this function is turned on, a Checkered Mark is printed on the first page
of fax documents to help you separate them.
Note
❒ You can turn this function on or off using Checkered Mark in the Facsimile
Features menu.
Reference
“Facsimile Features”, General Settings Guide
163
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
Center Mark
When this function is enabled, marks are printed halfway down the left side and
at the top center of each page received.
This makes it easy for you to position a hole puncher correctly when you file re-
ceived documents.
3
Note
❒ The Center Mark may deviate a little from the exact center of the edge.
❒ You can enable or disable this function using Center Mark in the Facsimile
Features menu.
Reference
“Facsimile Features”, General Settings Guide
Reception Time
You can have the date, time, and file number printed at the bottom of the docu-
ment when it is received.
Note
❒ You can turn this function on or off using Print Reception Time in the Facsim-
ile Features menu.
❒ When a received document is printed on two or more sheets, the reception
time is printed on the last page.
❒ The time when the document was printed can also be recorded on the docu-
ment. If you need this function, contact your service representative.
Reference
“Facsimile Features”, General Settings Guide
164
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Options
Two-Sided Printing
You can have a received document printed on both sides of a sheet.
3
Important
❒ To use this function, all pages of the received document must be of the same
size-inform the sending party of this beforehand if necessary. You must also
have paper set in the machine of the same size as that sent by the sending par-
ty. In Two-Sided Printing, this machine will correctly receive in A3L, B4 JIS
(Japanese Industrial Standard)L, A4KL, B5 JISKL, A5KL(11"×17"L,
81/2"×14"L, 81/2"×11"KL, 81/2"×51/2"L). The following table shows the re-
sults that can be achieved when receiving with this machine.
❒ This function works only when all pages are of the same width and received
into memory.
165
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
Note
❒ You can turn this function on or off using 2 Sided Print in the Facsimile Fea-
tures menu.
❒ Printouts may vary depending on how the sender sets the originals.
❒ You can select to have documents only from selected senders printed in this
way.
❒ Stored documents of the same size are printed on the same paper. Some
stored documents may be unavailable for this printing option.
Reference
3
“Facsimile Features”, General Settings Guide
180-degree rotation printing
When printing on both sides of the paper, this machine rotates images as shown
in the diagram.
CP2B02E0
Multi-Copy Reception
If you switch this function on, multiple copies of each incoming fax document
are printed.
You can also select to have multiple copies made of documents from particular
senders.
166
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Options
Note
❒ The maximum number of copies that can be made for each document is 10.
❒ When using the Multi-copy function with specified senders, the maximum
number of copies is 10.
❒ You can turn this function on or off using Reception File Print Quantity in the
Facsimile Features menu.
❒ The machine will use Memory Reception for Multi-copy Reception.
Reference
“Facsimile Features”, General Settings Guide
3
Image Rotation
If you have set paper in the standard tray K, incoming fax documents are auto-
matically rotated to fit onto the paper.
Note
❒ If you specified a tray for “Paper Tray” in the Facsimile Features menu, the
paper loaded in the specified tray is selected.
167
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
Page Separation and Length Reduction
If the size of a received document is longer than the paper loaded in the machine,
each page of the document can be split and printed on several sheets, or reduced
and printed on a single sheet.
3
For example, this function splits the document if the document length is 20 mm
(0.79") or longer than the paper used. The document is reduced if it is less than
20 mm (0.79"). When a document is split, an asterisk (p) is inserted at the split
position and about 10 mm (0.39") of the split area is duplicated on the top of the
second sheet.
Note
❒ Your service representative can customize this function with the following
settings:
• Reduction
• Print split mark
• Overprinting
• Overprinting length
• Guideline for split
❒ You can adjust the overprinting and reduction lengths within the following
ranges:
• Overprinting length: 4 mm (0.16"), 10 mm (0.39"), 15 mm (0.59")
• Guideline for split: 5-155 mm (5 mm steps)/0.2-6.1" (0.2" steps)
168
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Options
Page Reduction
If you receive a document that is longer than the paper in the tray, the machine
usually prints it on two pages.
3
If you turn this function on, the machine reduces the width and length of the re-
ceived image so that it will fit on one page. If A4L paper is loaded and a docu-
ment of B4 JISL size is received, the machine will reduce the document to a
single A4L sheet.
Note
❒ You can turn this function on or off with the User Parameters (switch 10, bit
3) in the Facsimile Features menu.
Reference
p.168 “Page Separation and Length Reduction”
“Facsimile Features”, General Settings Guide
TSI Print (Transmitting Subscriber Identification Print)
Usually the sender's Fax Header is printed on received documents. When you
receive an Internet Fax document, the e-mail address of the sender is printed. If
the sender has not programmed their Fax Header, you will not be able to iden-
tify them. However, if you turn this function on, the sender's Own Name or Own
Fax Number is printed instead so you can find out where the document came
from.
Note
❒ You can turn this function on or off in the User Parameters (switch 02, bit 3)
in the Facsimile Features menu.
Reference
“Facsimile Features”, General Settings Guide
169
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
If There Is No Paper of the Correct Size
If there is no paper in the machine that matches the size of a received document,
the machine will choose a paper size based on the paper available.
Page reduction
Disabled
Enabled
Reduction in Sub-scan Direction
Page Separation Threshold
Width or Length Priority
20 mm (0.79")
Width
3
Note
❒ The document is split over two sheets of paper depending on the paper size.
❒ Paper placed in the bypass tray is not usually selected for printing a received
document. However, you can use this tray if you select the bypass tray as the
main paper tray using Reception with Specified Senders.
❒ Widths that this machine can receive are A4, B4 JIS, LT (81/2"×11") and A3.
Any documents narrower than A4 or LT (81/2"×11") are received at A4 or LT
(81/2"×11") width. The length of documents depends on the document.
❒ The paper size used to print a received document may be different from the
size of the sent original.
p.168 “Page Separation and Length Reduction”
p.169 “Page Reduction”
“Facsimile Features”, General Settings Guide
Setting priority trays
With the same size of paper loaded into multiple trays, you can make the ma-
chine use one tray for one function and another tray for another function.
For example, you may load white A4 paper into tray 1 to use when making cop-
ies, and yellow A4 paper into tray 2 to use when printing received faxes. You can
then easily identify for which purpose paper has been output. You can perform
this setting in “Paper Tray Priority: Facsimile” in “System Settings”.
Note
❒ When a different size of document from the priority tray is received, the tray
containing the same size of paper as the received document is used.
Reference
“System Settings”, General Settings Guide
170
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Options
Just size printing
If you enable this function, received documents are printed on the sheet that has
the highest priority.
This function is enabled with User Parameters (switch 05, bit 5) in the Facsimile
Features menu.
If the paper tray is not stocked with paper of a suitable size to print a received
document, a message appears on the display prompting you to load paper of the
required size. When you have loaded new paper, press [Exit] to print the docu-
ment.
3
Note
❒ After pressing [Exit], procedure varies depending on machine status when the
message occurred.
• If any received documents or reports were being printed automatically, the
printer automatically continues printing from where it left off.
• If any documents or reports were being printed manually, the printer does
not resume printing. Perform the operation from the beginning again.
Reference
“Facsimile Features”, General Settings Guide
Having incoming documents printed on paper from the bypass tray
You can print documents sent from Specified Senders on paper from the bypass
tray.
Set as follows:
• Program a special sender and select the Bypass Tray for the paper tray type.
• In “Program Special Sender” in the Facsimile Features menu, turn on the
“Special Reception Function” in “Initial Set Up”.
Important
❒ When using this function, printed sheets cannot be delivered to the finisher
output tray. Even if you specify the finisher output tray, sheets are delivered
to the Internal Tray 1.
171
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
Note
❒ You can load a maximum of 100 sheets of standard paper in the bypass tray.
❒ You can use a size of paper not loaded in the paper tray(s) in the bypass tray.
❒ The machine can detect A6L, A5L, A4L, A3L (51/2"×81/2"L, 81/2"×11"L,
11"×17"L) paper sizes. When you load any other size, specify the paper size.
However, if the specified paper size and size of paper set in the bypass tray
do not match, paper jams may occur, or the image may be shortened.
❒ When using tray 1 of the optional 1000-sheet finisher, paper is output to the
tray even with custom sizes selected.
❒ Documents printed on paper smaller than A4 may be shortened, or split
3
across sheets.
❒ Paper longer than 600 mm may be creased, not sent, or jam.
❒ Print area depends on optional expansion memory, resolution, and vertical
length of originals.
❒ If you use this function, Image Rotation and 180-degree rotating printing are
not possible.
Reference
“Facsimile Features”, General Settings Guide
Where Incoming Documents Are Delivered - Output Tray
You can specify the output tray or output position to facilitate separation of re-
ceived documents.
Specifying tray for lines
Use this function to specify the output tray for each line port.
You can specify the document feeding tray for each port (telephone, Internet
Fax, IP-Fax). For example, you can specify documents received through the G3-
1 port to be fed to the “Internal Tray 1” and documents received through the G3-
2 port to be fed to the “Internal Tray 2”, facilitating separation of files. You can
also set the machine to output Internet Fax documents and ordinary faxes onto
different trays.
Important
❒ The optional extra G3 interface unit is required.
Note
❒ To use this function, specify the port and destination using [Specify Tray for
Lines] in the Facsimile Features menu.
❒ Available output tray depends on the type of finisher.
Reference
“Facsimile Features”, General Settings Guide
172
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Options
Tray Shift
Use this function to shift the output position for each document, so you can sep-
arate received documents easily.
Important
❒ The optional finisher or shift sort tray unit is required.
When the optional finisher unit is selected for fax output, you can use the Tray
Shift function whenever a fax or report is printed.
This is useful for separating faxes stacked in the finisher output tray. For exam-
ple, if the previous incoming fax was output to the left, the next incoming fax
will be output to the right and vice-versa.
3
Note
❒ You can turn this function on or off with the User Parameters (switch 19, bit
0) in the Facsimile Features menu.
Reference
“Facsimile Features”, General Settings Guide
173
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception
3
174
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Changing/Confirming
Communication Information
This section explains the features of [Change TX / Info], which you can use to con-
firm communication results on the screen or printed reports.
Changing the Settings of Files in Memory
After you have pressed the {Start} key (after scanning originals), you can check
and edit the destination or settings of Memory Transmission. You can also can-
cel a transmission, change the settings of a transmission, print a stored file, print
a list of stored files, and resend a file which the machine failed to transmit.
Note
❒ If the “No transmission files found.” message appears on the screen af-
ter you press [Check / Stop Transmission File], no files are being stored or sent
by Memory Transmission.
❒ You cannot check or edit a file being sent. Also a SUB Code Transmission file
or stored file to be printed as a report cannot be checked or edited.
❒ There are cases when a destination may not be selected as the destination ap-
pears as “p”, depending on the security settings.
175
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
Deleting a Destination from a Simultaneous Broadcast
You can delete selected broadcasting destinations.
Important
❒ If you delete a destination that is the only destination for a transmission, the
transmission is canceled.
A Press [Change TX / Info].
4
B Press [Check / Stop Transmission File].
C Select the file from which you want to delete a destination.
176
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Settings of Files in Memory
D Press [Check / Change Settings].
E Press [Change] for the destination you want to delete.
4
F Press the {Clear/Stop} key to delete the destination, and then press [OK].
ALV016S
Pressing the {Clear/Stop} key deletes by single digits the fax number or IP-Fax
address. The Internet Fax address can be entirely deleted at once by pressing
the {Clear/Stop} key.
G Press [Exit].
To delete another destination, repeat from step .
C
H Press [Exit] twice.
The standby display appears.
177
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
Adding a Destination
You can add a destination for broadcasting.
A Press [Change TX / Info].
4
B Press [Check / Stop Transmission File].
C Select the file to which you want to add a destination.
178
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Settings of Files in Memory
D Press [Check / Change Settings].
E Press [Add Destination].
4
F Specify the destination using the number keys or Destination keys, and
then press [OK].
When the file has some Internet Fax destinations, you can switch the transmis-
sion type between fax/IP-Fax and Internet Fax by pressing
[
Fax
]
or [Internet Fax].
To add an e-mail address, switch the type of transmission to Internet Fax by
pressing [Internet Fax]. Then, press [Manual Entry] and enter the e-mail address.
You can also program a SUB Code or SEP Code by pressing [Adv.Features].
G Press [Exit].
Repeat from step , if you want to add another destination.
C
H Press [Exit] twice.
The standby display appears.
179
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
Changing the Transmission Time
You can change the transmission time specified with Send Later.
You can also delete the transmission time. If the transmission time is deleted, the
file is transmitted immediately.
A Press [Change TX / Info].
4
B Press [Check / Stop Transmission File].
C Select the file for which you want to change or cancel the transmission
time.
180
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Settings of Files in Memory
D Press [Check / Change Settings].
E Press [Change TX Time].
4
F Press [Clear], re-enter the transmission time using the number keys, and
then press [OK].
If you press [Transmit Now], the file is transmitted immediately. However, if
there is a file on standby, that file is sent first.
G Press [Exit].
Repeat from step , if you want to change another transmission time.
C
H Press [Exit] twice.
The standby display appears.
181
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
Changing the SMTP Server Setting
You can change the settings for whether or not to bypass the SMTP server.
A Press [Change TX / Info].
4
B Press [Check / Stop Transmission File].
C Select a file whose SMTP server setting you want to change.
182
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Settings of Files in Memory
D Press [Check / Change Settings].
E Press [Change].
4
F Press [SMTP].
G Select [Yes] or [No], and then press [OK].
183
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
H Press [OK].
I Press [Exit].
4
Repeat from step to change the SMTP server settings of other recipients.
C
J Press [Exit] twice.
The standby display appears.
184
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing a File from Memory
Printing a File from Memory
If you want to check the contents of a file that is stored in memory and not yet
sent, use this procedure to print it out.
A Press [Change TX / Info].
4
B Press [Check / Stop Transmission File].
C Select the file you want to print.
If multiple destinations were specified, only the number of destinations for
unsent documents appears.
185
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
D Press [Print].
If you want two-sided printing, press [Print on 2 Sides].
To cancel printing, press [Cancel]. The display returns to that of step .
C
4
E Press the {Start} key.
play returns to that of step .
C
Repeat from step , if you want to print another file.
C
F Press [Exit] twice.
The standby display appears.
Note
❒ You can also print files that have not been successfully transmitted.
186
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing a List of Files in Memory (Print TX File List)
Printing a List of Files in Memory (Print TX
File List)
Print this list if you want to find out which files are stored in memory and what
their file numbers are. Knowing the file number can be useful (for example when
erasing files).
A Press [Change TX / Info].
B Press [Check / Stop Transmission File].
C Press [Print List].
4
To cancel printing before pressing the {Start} key, press [Cancel]. The screen
returns to that displayed before pressing [Print List].
187
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
D Press the {Start} key.
To cancel printing after pressing the {Start} key, press [Stop Printing]. The dis-
play returns to that of step .
C
E Press [Exit] twice.
The standby display appears.
Note
❒ The contents of a file stored in memory can also be printed.
❒ You can set whether or not to display a sender name with the User Param-
eters (switch 04, bit 5) in the Facsimile Features menu.
Reference
“Facsimile Features”, General Settings Guide
4
188
Download from Www.Somanuals.com. All Manuals Search And Download.
Resending a File
Resending a File
Machine memory stores documents that could not be successfully transmitted
using Memory Transmission. Use this procedure to resend these documents.
Important
❒ Set “Store documents in memory that could not be transmitted” to “On” in
User Parameters (switch 24, bit 0) in the Facsimile Features menu.
A Press [Change TX / Info].
4
B Press [Check / Stop Transmission File].
C Select the file you want to resend.
“TX failed” is displayed for files that could not be sent.
If multiple destinations were specified, only the destination you specify first
appears.
If multiple destinations were specified, only the number of destinations for
unsent documents appears.
189
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
D Press [Transmit Failed File].
To add a destination, press [Add Destination], and then specify the destination.
E Press [OK].
4
Repeat from step to resend another file.
C
To cancel transmissions, press [Cancel]. The display returns to that of step .
D
F Press [Exit] twice.
The standby display appears.
Transmission starts.
Note
❒ Files that could not be transmitted are kept for either 24 or 72 hours, de-
pending on the setting you make in User Parameters (switch 24, bit 1) in
the Facsimile Features menu.
Reference
“Facsimile Features”, General Settings Guide
190
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the Transmission Result (Transmission File Status)
Checking the Transmission Result
(Transmission File Status)
You can confirm transmission by the display, report, or e-mail.
Confirming on Display
Follow these steps to display the transmission results.
A Press [Change TX / Info].
4
B Select [Transmission File Status].
C Check the transmission results.
Transmission results are displayed, from the latest result down, in groups of
nine.
When a fax is sent, “Destination” shows the Own Fax Number or Fax Header
information of the receiver. When an Internet Fax is sent, the e-mail address
and name programmed in the destination list appears. For a transmission
from a computer, “-- LAN-Fax -->” is shown.
Depending on security settings, the destination may appear as p.
D Press [Exit] twice.
The standby display appears.
191
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
Note
❒ Only the transmission results of the latest communications are displayed.
For the maximum number of communication results you can check on this
machine, see “Maximum Values”.
❒
You can view sent fax documents and their lists, using a Web Image Moni-
tor on a network computer. For details, see the Web Image Monitor's Help.
❒
If a transmission is completed while you are using this function, the result will not
appear. To view the latest result, exit Transmission File Status, and then try again.
❒ You can program one of the Quick Operation keys with operations for this
function. Using the key allows you to omit step .
A
❒ When documents are transmitted from the computer to the machine, --
LAN-Fax --> appears. To check if the documents are sent to the receiver,
4
Reference
p.278 “Maximum Values”
“Facsimile Features”, General Settings Guide
Confirming by Report
Print reports for confirmation.
❖ Memory Transmission
If a document cannot be sent, a Communication Failure Report is automati-
cally printed. Or, you can use the Communication Result Report to check each
transmission result regardless of status.
This report is printed each time a Memory Transmission is completed if turned
on with User Parameters (switch 03, bit 0) in the Facsimile Features menu.
You can also print the report by programming the TX Status Report to a Quick
Operation key and pressing this when specifying a destination.
If you turn the Communication Result Report on, the Communication Failure
Report is not printed.
❖ Immediate Transmission
You can confirm the result with an Immediate TX Result Report.
Select to print this report in User Parameters (switch 03, bit 5) in the Facsimile
Features menu. A report is printed after every Immediate Transmission is
completed.
You can also print the report by programming the TX Status Report to a Quick
p.194 “Immediate TX Result Report (Immediate Transmission)”
p.195 “Communication Failure Report”
“Facsimile Features”, General Settings Guide
192
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the Transmission Result (Transmission File Status)
Confirming by E-mail
Use the E-mail TX Results function to send reports by e-mail to a computer, and
then confirm them on the computer.
The available reports are:
• Communication Result Report.
• Immediate TX Result Report.
• Polling with SEP Rx Result.
Important
❒ You must first register the e-mail addresses of the destinations the report is to
be sent to on the destination list.
4
Note
❒ By programming the E-mail TX Results to a Quick Operation key in advance,
you can send transmission results by e-mail after each transmission is com-
pleted. Select the destination for notification from the Internet Fax destina-
tions in the destination list.
❒ When using the Sender Name function to select the sender, the transmission
results are sent to senders' e-mail addresses that have been registered. Select
the sender from the Internet Fax destinations in the destination list.
❒ If you send fax documents from a computer, use LAN-Fax Driver to specify
p.194 “Immediate TX Result Report (Immediate Transmission)”
p.198 “Print Journal”
“Facsimile Features”, General Settings Guide
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gener-
al Settings Guide
Confirming by Report and E-mail
You can confirm transmission results using both the E-mail TX Results function,
which sends the results by e-mail, and the Communication Result Report print-
ed by the machine.
You can set whether to use both of these together in User Parameters (switch 10,
bit 6) in the Facsimile Features menu.
Reference
“Facsimile Features”, General Settings Guide
193
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
Communication Result Report (Memory Transmission)
This report is printed when a Memory Transmission is completed, so you can
check the result of the transmission.
Note
❒ If E-mail TX Results is programmed in a Quick Operation key, you can select
whether a report e-mail is sent after transmission.
❒ If two or more destinations are specified, this report is printed after the fax
document is sent to all the destinations.
❒ If the machine is set up not to print this report and the fax document could
not be successfully transmitted, a Communication Failure Report is printed.
❒ You can turn this function on or off with the User Parameters (switch 03, bit
4
0) in the Facsimile Features menu.
❒ You can display a sender name with the User Parameters (switch 04, bit 5) in
the Facsimile Features menu.
❒ You can select whether to include part of the original image on the report with
the User Parameters (switch 04, bit 7) in the Facsimile Features menu.
❒ To view the report without text disruption, select a font of even character
width in your e-mail application's settings.
❒ You can set whether or not to display a destination with the User Parameters
(switch 04, bit 4) in the Facsimile Features menu.
❒ The Pg(s) column gives the total number of pages. The Page Not Sent column
gives the number of pages that could not be sent successfully.
❒ “--” indicates that the Internet Fax document was sent to the mail server pro-
grammed in this machine. (However, this does not mean the e-mail was de-
livered.)
Reference
p.195 “Communication Failure Report”
“Facsimile Features”, General Settings Guide
Immediate TX Result Report (Immediate Transmission)
If you turn this report on, a report is printed after every Immediate Transmission
so you have a record of whether the transmission was successful or not.
If the machine is set up not to print this report and the fax document could not
be successfully transmitted, the Error Report is printed instead.
194
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the Transmission Result (Transmission File Status)
Note
❒ If E-mail TX Results is programmed in a Quick Operation key, you can select
whether a report e-mail is sent after transmission.
❒ You can switch this report on or off in the User Parameters (switch 03, bit 5)
in the Facsimile Features menu.
❒ To view the report without text disruption, select a font of even character
width in your e-mail application's settings.
❒ You can set whether or not to display a destination with the User Parameters
(switch 04, bit 4) in the Facsimile Features menu.
❒ If the page was sent successfully, the Page column gives the total number of
pages sent successfully.
Reference
4
“Facsimile Features”, General Settings Guide
Communication Failure Report
This report is printed when a document could not be successfully transmitted
with Memory Transmission.
If the machine is set up to print a Communication Result Report, this report is not
printed. Use it to keep a record of failed transmissions so you can send them again.
Note
❒ You can select whether the Communication Failure Report is automatically
printed using the User Parameters (switch 04, bit 1) in the Facsimile Features
menu.
❒ This report is only printed if the Communication Result Report is turned off
and a document could not be successfully transmitted with Memory Trans-
mission.
❒ You can select whether to include part of the original image on the report with
the User Parameters (switch 04, bit 7) in the Facsimile Features menu.
❒ You can display a destination with the User Parameters (switch 04, bit 4) in
the Facsimile Features menu.
❒ You can set whether or not to display a sender name with the User Parame-
ters (switch 04, bit 5) in the Facsimile Features menu.
❒ The Pg(s) column gives the total number of pages. The Page Not Sent column
gives the number of pages that could not be sent successfully.
❒ “Unprogrammed” indicates that the document could not be sent because the
forwarding destination is not programmed.
❒ “--” indicates that the Internet Fax document was sent to the mail server pro-
grammed in this machine. (However, this does not mean the e-mail was de-
livered.)
Reference
“Facsimile Features”, General Settings Guide
195
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
Checking the Reception Result
(Reception File Status)
Confirm the reception result on the screen or in a report.
Confirming on Display
Follow these steps to display the reception result.
A Press [Change TX / Info].
4
B Press [Reception File Status].
C Check the reception results.
Reception results are displayed, from the latest result, in groups of nine.
When a fax or IP-Fax is received, “Sender” shows the Own Fax Number or
Fax Header information. When an Internet Fax is received, the sender's e-mail
address appears.
D Press [Exit] twice.
The standby display appears.
196
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the Reception Result (Reception File Status)
Note
❒ Only the reception results of the latest communications are displayed. For
the maximum number of communication results you can check on this ma-
chine, see “Maximum Values”.
❒ You can view received fax documents and their lists, using a Web Image
Monitor on a network computer. For details, see the Web Image Monitor's
Help.
❒ If a document is received while you are using this function, the result will
not appear. To view the latest result, exit Reception File Status, and then
try again.
❒ You can program one of the Quick Operation keys with operations for this
A
Reference
p.278 “Maximum Values”
4
“Facsimile Features”, General Settings Guide
Confirming by Report
Print a report to confirm reception results.
Journal
Print the Journal to confirm the latest reception results. For details, see “Jour-
nal”.
Reference
p.203 “Journal”
197
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
Print Journal
You can print the Journal manually.
Important
❒ The contents of a Journal printed automatically are deleted after printing.
Keep the journal if you require a record of transmissions and receptions.
Printing the Journal
To print the Journal manually, select the printing method: “All”, “Print per File
No.”, or “Print per User”.
Note
4
❒ You can set whether the Journal is automatically printed after every 50 com-
munications in User Parameters (switch 03, bit 7) in the Facsimile Features
menu.
❒ You can display a sender name with the User Parameters (switch 04, bit 5) in
the Facsimile Features menu.
❒ Depending on security settings, the Journal is not automatically printed.
❒ You can set whether the Journal is printed by line type with the User Param-
eters (switch 19, bit 1) in the Facsimile Features menu.
❒ You can program one of the Quick Operation keys with operations for this
function. Using the key allows you to omit the step where you press [Change
TX / Info].
❒ Depending on security settings, the destination may not appear.
❒ For the maximum number of communication results printed in the Journal,
Reference
p.278 “Maximum Values”
“Facsimile Features”, General Settings Guide
198
Download from Www.Somanuals.com. All Manuals Search And Download.
Print Journal
All
Prints the results of communications in the order made.
A Press [Change TX / Info].
4
B Press [Print Journal].
C Select [All].
To cancel a file printing, press [Stop Printing]. The display returns to that of
step .
C
E Press [Exit] twice.
The standby display appears.
199
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
Print per File No.
Prints only the results of communications specified by file number.
A Press [Change TX / Info].
4
B Press [Print Journal].
C Select [Print per File No.].
D Enter a 4-digit file number.
If you make a mistake, press [Clear] or the {Clear/Stop} key, and then try again.
E Press the {Start} key.
To cancel a file printing, press
[Stop Printing]. The display returns to that of step
.
C
F Press [Exit] twice.
The standby display appears.
200
Download from Www.Somanuals.com. All Manuals Search And Download.
Print Journal
Print per User
Prints the results of communications by individual senders.
A Press [Change TX / Info].
4
B Press [Print Journal].
C Select [Print per User].
D Select a user.
Press [Cancel] if the user is not registered. The display returns to that of step .
C
Press [Cancel] if a wrong user name is selected. The display returns to that of
step .
C
201
Download from Www.Somanuals.com. All Manuals Search And Download.
Print Journal
Journal
This section explains the items printed in the Journal.
4
ALV014S
1. Printing date
5. Other end
• For fax destinations
Shows the date and time the report was
printed.
Shows the name (for display) pro-
grammed by the other end.
Shows the programmed fax number if
the name (for display) was not pro-
grammed.
2. Programmed Fax Header
Shows the sender name programmed for
printing.
If neither name nor fax number was
programmed by the other end, an en-
tered fax number or a name pro-
grammed in a destination list is
shown for transmissions.
3. Date
Shows the transmission or reception
date.
4. Time
Shows the transmission or reception start
time.
203
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
• For Internet Fax destinations
At time of transmission, it shows the
e-mail address or name programmed
in the destination list. At time of re-
ception, it shows the e-mail address of
the sender.
• For IP-Fax transmissions and recep-
tions
After
, and “T” for outgoing faxes
or “R” for incoming faxes, the com-
munication mode appears in alpha-
betical letters or symbols.
At time of broadcasting transmission,
it shows the number of destinations
after the e-mail addresses or names of
destination.
When documents are transmitted
from the computer to the machine, --
LAN-Fax --> appears. To check if the
documents are sent to the receiver,
confirm the same File No.
• For forwarding to the folder destina-
tions
After
(folder mark) and “T” for
outgoing faxes, the communication
mode appears in alphabetical letters
or symbols.
7. Communication time
Shows time taken for transmissions or re-
ceptions.
• For IP-Fax destinations
Shows the IP-Fax destination or name
programmed in the destination list.
The fax destination details appear on
the reception report.
4
8. Number of pages
Shows the number of pages transmitted
or received.
• For Folder destinations
Shows the name programmed in the
destination list.
9. Communication result
Shows the result of transmissions or re-
ceptions.
6. Communication mode
OK: All pages were properly transmitted
or received. When Reception Notice is ac-
tivated using “TX Mode”, receipt of Re-
ception Notice is shown. The results of
received documents that were routed are
preceded by “n”.
--: The Internet Fax document was sent to
the mail server programmed in this ma-
chine. (However, this does not mean the
e-mail was delivered.) When using LAN-
Fax, the results of communication from a
computer to this machine are shown.
• For fax transmissions and receptions
After the line type, and “T” for outgo-
ing faxes or “R” for incoming faxes,
the communication mode appears in
alphabetical letters or symbols. If the
optional extra G3 interface unit is in-
stalled, “G3-1”, “G3-2”, or “G3-3” ap-
pears.
• For Internet Fax transmissions and re-
ceptions
After
, and “T” for outgoing e-
mail or “R” for incoming e-mail, the
communication mode appears in al-
phabetical letters or symbols. A “Q”
indicates outgoing e-mail for which a
Reception Notice is set in “TX Mode”,
whereas an “A” indicates reception
notice e-mail.
Error: A communication error occurred.
D: Power was disconnected during com-
munication. Not all fax documents were
transmitted.
10. User name
Shows the sender's name.
11. File number
Shows file management numbers.
Note
❒ To prioritize a fax number or name programmed in the destination list, con-
tact your service representative.
204
Download from Www.Somanuals.com. All Manuals Search And Download.
Print Journal
Transmitting Journal by E-mail
Use this function to send the Journal to the administrator's e-mail address.
The Journal is sent automatically after every 50 communications. A CSV format
Journal is attached to the e-mail.
Important
❒ To transmit the Journal by e-mail, it is necessary to make settings with User
Parameters (switch 21, bit 4) in the Facsimile Features menu.
❒ This machine does not store sent CSV files. It is recommended that you dou-
ble-check the e-mail address of an administrator before the Journal is trans-
mitted. If the e-mail address of the administrator is not correct, your
important Journal may be lost. Sent CSV files are not left on the fax machine.
4
Note
❒ If the administrator's address is wrong, you may not be able to acquire the
Journal.
❒ If the Journal fails to be transmitted in e-mail format, the Journal is printed
out.
❒ The name of an attached CSV file is “JOURNALnyear, month, date, hours,
minutes”. For example, the file name transmitted in 14:40 on 20th, December,
2005 is “JOURNAL200512201440.csv”.
❒ The subject of a Journal sent by e-mail begins with “Journal”.
Reference
“Facsimile Features”, General Settings Guide
Journal by e-mail
If the setting is made so that the Journal is transmitted as e-mail, it is transmitted
to the e-mail address of an administrator.
Note
❒ To transmit the Journal, it is necessary to make settings with the User Param-
eters (switch 21, bit 4) in the Facsimile Features menu.
❒ You can set whether or not to display a sender name with the User Parame-
ters (switch 04, bit 5) in the Facsimile Features menu.
❒ To set the administrator e-mail address, see “System Settings”, General Set-
tings Guide.
❒ Depending on security settings, the Destination/Sender name may not ap-
pear.
Reference
p.125 “Requesting a Reception Notice”
“System Settings”, General Settings Guide
“Facsimile Features”, General Settings Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
205
Changing/Confirming Communication Information
Printing/Deleting Received and Stored
Documents (Print/Delete Stored
Reception File)
You can print documents that are received and stored on the hard disk. You can
also delete unwanted documents.
4
Important
❒ Make the settings for received and stored documents in “Reception File Set-
ting” in the Facsimile Features menu before using this function.
Note
❒ If you have selected to store received documents and specified an e-mail ad-
dress for notification of receipt, fax reception notification can be sent to that
e-mail address.
❒ For the maximum number of received documents you can store on the ma-
chine's hard disk, see “Maximum Values”.
❒ You can view and print received and stored documents using a Web Image
p.261 “Viewing Fax Information Using a Web Browser”
p.278 “Maximum Values”
“Facsimile Features”, General Settings Guide
DeskTopBinder's manuals and Help
206
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing/Deleting Received and Stored Documents (Print/Delete Stored Reception File)
Printing Received and Stored Documents
Use the following procedure to print documents saved on the hard disk.
A Press [Change TX / Info].
4
B Press [Print / Delete Stored Reception File].
C Select a file to be printed, and then press [Print].
To cancel printing, press [Cancel].
To delete the document after printing, press [Delete File after Printing].
To perform two-sided printing, press [Print on 2 Sides] before pressing the
{Start} key.
D Press the {Start} key.
E Press [Exit] twice.
The standby display appears.
Note
❒ This function allows you to print only received and stored documents.
❒ You cannot print and delete received documents using the Document
Server function.
❒ You can program one of the Quick Operation keys with operations for this
function. Using the Quick Operation key allows you to omit step .
A
❒ You can specify and print multiple documents. For the maximum number
of documents you can specify at a time, see “Maximum Values”.
207
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
Reference
p.278 “Maximum Values”
“Facsimile Features”, General Settings Guide
Deleting Received and Stored Documents
Use the following procedure to delete documents stored on the hard disk.
A Press [Change TX / Info].
4
B Press [Print / Delete Stored Reception File].
C Select a file to be deleted, and then press [Delete].
D Press [Yes].
To cancel a deletion, press [No]. The display returns to that of step .
C
E Press [Exit] twice.
The standby display appears.
Note
❒ You cannot delete a document while another person is previewing or
printing it using a Web Image Monitor or DeskTopBinder.
❒ You can specify and delete multiple documents. For the maximum number
Reference
p.278 “Maximum Values”
208
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing a File Received with Memory Lock
Printing a File Received with Memory Lock
This is a security function designed to prevent unauthorized users from reading
your documents. If Memory Lock Reception is switched on, all received docu-
ments are stored in memory and are not automatically printed. To print the doc-
uments, you have to enter the Memory Lock ID. When your machine has
received a document with Memory Lock Reception, the Confidential File (i)
indicator blinks.
Before using this function, the following preparations are required.
• Program your Memory Lock ID.
• Set Memory Lock Reception to On.
Important
4
❒ If the main power switch is turned off for about an hour, all documents pro-
tected by Memory Lock Reception are deleted. When this happens, the Power
Failure Report is printed so you can confirm which documents have been de-
leted. For details, see “Troubleshooting When Using the Facsimile Function”,
Troubleshooting.
A Confirm that the Confidential File indicator is blinking.
ALV017S
B Press [Change TX / Info].
C Press [Print Memory Lock].
If no documents were received while Memory Lock Reception was switched
on, the message “No reception file.” is shown. Press [Exit] .
209
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
D {ESnttaerrt}ak4e-yd.igit Memory Lock ID with the number keys, and then press the
If the Memory Lock ID does not match, the “Specified code does not
correspond to programmed Memory Lock ID.” message appears. Press
[Exit] and retry after checking the Memory Lock ID.
4
E Press [Exit].
The standby display appears.
Note
❒ If Memory Lock Reception and received document storage are both set to
on, Memory Lock Reception is unavailable and received documents be-
come stored documents.
❒ Even when Memory Lock Reception is available, if free memory is insuffi-
cient, reception is not possible.
❒ You can also apply a Memory Lock Reception to documents that come
only from certain senders.
❒ Documents received by SEP Code Reception are automatically printed
even if this function is switched on.
❒ You can program one of the Quick Operation keys with operations for this
function. Using the key allows you to omit step .
B
p.206 “Printing/Deleting Received and Stored Documents (Print/Delete
Stored Reception File)”
“Facsimile Features”, General Settings Guide
“Troubleshooting When Using the Facsimile Function”, Troubleshooting
210
Download from Www.Somanuals.com. All Manuals Search And Download.
Personal Boxes
Personal Boxes
You can receive confidential documents in Personal Boxes.
Important
❒ Before using this function, set the Personal Box in advance.
Personal Boxes
Storing your documents in a Personal Box prevents unauthorized users reading
them.
When you specify a receiver for the Personal Box, incoming documents are for-
warded directly to the destination you specify. You can specify a fax number, e-
mail address, or IP-Fax destination as the receiver.
4
To be able to receive documents into a Personal Box, you must inform the sender
of the SUB Code programmed for that Personal Box and ask them to send the
document using SUB Code Transmission with that SUB Code. When your ma-
chine has received a confidential document, the Confidential File (i) indicator
lights.
Important
❒ If the main power switch is turned off for about an hour, all documents re-
ceived into Personal Boxes are deleted. When this happens, the Power Failure
Report is printed so you can confirm which documents have been deleted.
For details, see “Troubleshooting When Using the Facsimile Function”, Trou-
bleshooting.
❒ Documents delivered to registered destinations are deleted from Personal
Boxes.
Note
❒ If a receiver is not assigned, you can print the received documents on this ma-
chine. See “Printing Personal Box Documents”.
p.212 “Printing Personal Box Documents”
p.213 “Confidential File Report”
“Troubleshooting When Using the Facsimile Function”, Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
211
Changing/Confirming Communication Information
Printing Personal Box Documents
Follow these steps to print a document received into a Personal Box.
A Make sure that the Confidential File indicator is lit.
4
ALV017S
B Press [Change TX / Info].
C Press [Print Personal Box File].
D Select the box with the document you want to print.
212
Download from Www.Somanuals.com. All Manuals Search And Download.
Personal Boxes
E If a password has been set for the box, enter the password, and then press
[OK].
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
4
To cancel entering a password, press [Cancel]. The display returns to that of
step .
D
F Press the {Start} key.
To stop printing, press [Stop Printing]. The display returns to that of step .
D
To print a document in another Personal Box, repeat from step .
D
G Press [Exit] twice.
The standby display appears.
Note
❒ If you print a Personal Box document, it is deleted.
❒ The passwords for Personal Boxes can be programmed under “General
Settings” in the Facsimile Features menu.
Reference
“Facsimile Features”, General Settings Guide
Confidential File Report
You can check whether a document was received in a Personal Box.
Note
❒ You can turn this function on or off with the User Parameters (switch 04, bit
0) in the Facsimile Features menu.
Reference
“Facsimile Features”, General Settings Guide
213
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
Information Boxes
This section describes how to use Information Boxes.
Important
❒ Before using this function, set the Information Box in advance.
Information Boxes
Use the Information Box function to set up the machine as a document server.
Program a document into an Information Box for others to pick up. When a re-
quest is made by another party, the SEP Code they specify is matched against
the SEP Codes programmed in that Information Box. If a code matches the doc-
ument stored in the Information Box the document is sent to the other party au-
tomatically.
4
Other parties can receive these documents whenever they request them.
Important
❒
If the main power switch is turned off for about an hour, all documents stored
in Information Boxes are deleted. When this happens, the Power Failure Report
is printed so you can confirm which documents have been deleted. For details,
see “Troubleshooting When Using the Facsimile Function”, Troubleshooting.
❒ For other parties to be able to retrieve a document programmed in an Infor-
mation Box, you need to inform the of the SEP Code assigned to that Informa-
tion Box.
Note
❒ For details about storing documents in the Information Boxes, see “Storing
Documents in Information Boxes”.
❒ You can set a password for Information Boxes in advance. A password can be
Reference
p.215 “Storing Documents in Information Boxes”
“Facsimile Features”, General Settings Guide
“Troubleshooting When Using the Facsimile Function”, Troubleshooting
214
Download from Www.Somanuals.com. All Manuals Search And Download.
Information Boxes
Storing Documents in Information Boxes
Follow these steps to store a document in an Information Box.
A Press [Change TX / Info].
4
B Press [Store / Delete / Print Information Box File].
C Select the box in which you want to store the file.
When there are pre-programmed files, a file mark appears to the left of the box name.
A message is displayed if you select a box with a file stored in it. Press [Yes]
when changing the file. The stored original file is overwritten.
D
If a password has been set for the box, enter the password, and then press [OK].
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then try again.
To cancel entering a password, press
[
Cancel
]
. The display returns to that of step
.
C
215
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
E Place the original, and then select the scan settings you require.
You can also select the following settings:
• Original Orientation
• Original Settings
4
• Stamp
F Press the {Start} key.
The machine starts to scan the original.
To stop scanning, press [Stop]. The display returns to that of step .
C
To store a document in another Information Box, repeat from step .
C
G Press [Exit] twice.
The standby display appears.
Note
❒ One Information Box stores one file.
❒ The stored file is not deleted automatically. If you want to delete a stored
file, see “Deleting Information Box Documents”.
Reference
p.218 “Deleting Information Box Documents”
216
Download from Www.Somanuals.com. All Manuals Search And Download.
Information Boxes
Printing Information Box Documents
Follow these steps to print a document stored in an Information Box.
A Press [Change TX / Info].
4
B Press [Store / Delete / Print Information Box File].
C Press [Print].
D Select the box that contains the stored file you want to print.
You cannot select a box that has no stored file.
E
If a password has been set for the box, enter the password, and then press [OK].
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
To cancel entering a password, press [Cancel]. The display returns to that of
step .
D
217
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
F Press the {Start} key.
If you want two-sided printing, press [Print on 2 Sides] before pressing the
{Start} key.
To stop printing before pressing the {Start} key, press [Cancel]. The display re-
turns to that of step .
D
play returns to that of step .
D
Repeat from step to print another stored file in the box.
D
G Press [Exit] twice.
The standby display appears.
4
Deleting Information Box Documents
Follow these steps to delete a file stored in an Information Box.
A Press [Change TX / Info].
B Press [Store / Delete / Print Information Box File].
C Press [Delete].
D Select the box that contains the stored file you want to delete.
218
Download from Www.Somanuals.com. All Manuals Search And Download.
Information Boxes
E If a password has been set for the box, enter the password, and then press
[OK].
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
4
To cancel entering a password, press [Cancel]. The display returns to that of
step .
D
F Press [Yes].
To stop deleting, press [No]. The display returns to that of step .
D
Repeat from step to delete another stored file in another box.
D
G Press [Exit] twice.
The standby display appears.
219
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing/Confirming Communication Information
4
220
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Storing a Document
This section explains storing and managing documents in the Document Server.
Sending a Stored File
This section describes how to store and manage fax documents in the Document
Server.
The Document Server can store documents from various applications.
The documents that are stored using the facsimile function are available to trans-
mit by facsimile.
Storing in the Document Server enables the following:
• Once stored, a document can be sent out as many times as you want, just by
selecting it.
• Storing a document does not use facsimile memory.
You can send and print multiple stored documents as a single document, and
also send them with scanned originals at the same time. Follow the instructions
under [Select Stored File] when sending or printing stored documents.
Important
❒ Data stored in the machine can be lost if there is an error on the machine's
hard disk. The manufacturer is not responsible for any damage that might re-
sult from the loss of data.
221
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Document
Note
❒ Stored documents are not deleted even if there is a power failure, or the main
power switch is turned off.
❒ You can specify whether or not the machine automatically deletes documents
from the Document Server after a certain number of days. The delete function
is preconfigured with the software and automatically deletes any stored doc-
ument that is more than three days (72 hours) old. You can change this setting
using “Auto Delete File in Document Server” under “System Settings” . See
“System Settings”, General Settings Guide.
❒ You cannot check received and stored documents through the Document
Server.
❒ Documents in the Document Server can be sent, printed, or deleted, and their
information can be changed using the Web Image Monitor.
❒ Using the DeskTopBinder or Web Image Monitor, documents you stored in
the Document Server can be downloaded and managed on the computer. See
“Document Server”, Copy/Document Server Reference.
5
❒ For the maximum values of the following items, see “Maximum Values”.
• Number of documents you can store in the Document Server using the fac-
simile function
• Number of pages per document you can store in the Document Server
• Number of pages you can store in the Document Server (in total – copy
function, facsimile function, printer function, and scanner function)
Reference
p.278 “Maximum Values”
“Utilizing Stored Documents”, About This Machine
“System Settings”, General Settings Guide
“Document Server”, Copy/Document Server Reference
Storing a Document
You can store and send a document at the same time. You can also just store a
document.
❖ File names
Scanned documents are automatically assigned names like “FAX0001” or
“FAX0002”.
❖ User Names
You can set this function if necessary to know who and what departments
stored documents in the machine.
❖ Password
You can set this function so as not to send to unspecified people.
222
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Stored File
A Place the original, and then select the scan settings you require.
Set “Original Orientation” correctly. If you do not, the top/bottom orienta-
tion of the original will not be displayed correctly in the preview.
B Press [Store File].
C Select [Send & Store] or [Store Only].
5
Select [Send & Store] to send documents after they are stored.
Select [Store Only] to store documents.
D Set the user name, file name, and password as necessary.
If you are not setting a user name, file name, or password, proceed to step .
E
You cannot change multiple documents at once.
E Press [OK].
The file name appears to the left of [Store File].
223
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Document
F If you have selected [Send & Store], specify the receiver.
If you have selected [Store Only], proceed to step .
G
G Press the {Start} key.
Note
Reference
p.36 “Setting the Original Orientation”
“System Settings”, General Settings Guide
Programming a user name
A Press [User Name].
5
B Press the user name to be programmed.
Press the title key to switch between titles.
To set a non-programmed user name, press [Manual Entry], and then enter the
name. User names entered by pressing [Manual Entry] are not programmed
into the user code.
C Press [OK].
Note
❒ Depending on the security settings, [Access Privileges] might be displayed
instead of [User Name]. For details about setting [Access Privileges], ask the
administrator.
224
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Stored File
Reference
“Entering Text”, About This Machine
Setting a file name
A Press [File Name].
B Enter the file name.
C Press [OK].
5
Reference
“Entering Text”, About This Machine
Setting a password
A Press [Password].
225
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Document
B Enter a password using the number keys, and then press [OK].
If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing
[OK], and then reenter your password.
You can enter up to four to eight digits.
C Enter the password again, and then press [OK].
5
Sending Stored Documents
The machine sends documents stored in the Document Server.
The documents stored in the Document Server can be sent again and again until
they are deleted. Once sent, documents are stored in the Document Server.
Therefore, you can send them in just one operation without having to set your
originals again.
Important
❒ Store the documents to be sent in advance. You can program a password for
this function. You can change the user names, file names, and passwords of
stored documents.
❒ You cannot use the following transmission methods:
• Immediate Transmission
• Parallel Memory Transmission
• On Hook Dial
• Manual Dial
A Press [Select Stored File].
226
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Stored File
B Select the documents to be sent.
When multiple documents are selected, they are sent in the order of selection.
• Press [Queue] to arrange the order of the documents to be sent.
• Press [File Name] to place the documents in alphabetical order.
• Press [User Name] to place the documents in order by programmed user
name.
5
• Press [Date] to place the documents in order of programmed date.
To view details about stored documents, press [Details].
Press the Thumbnails key to switch the screen to thumbnail display.
C If you select a document with a password, enter the password, and then
press [OK].
If the document does not have a password, proceed to step .
D
227
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Document
D When you want to add your originals to stored documents and send them
all at once, press [Original n Stored File] or [Stored file n Original].
When sending only stored documents, proceed to step .
E
When [Original n Stored File] is pressed, the machine sends the originals, and
then stored files. When [Stored file n Original] is pressed, the machine sends
the stored files, and then originals.
5
E Press [OK].
F Specify the destination, and then press the {Start} key.
To add an original to stored documents, place the original, and then select
any scan settings you require.
The added originals are not stored.
Note
❒ You can send only documents saved with the facsimile function in the Doc-
ument Server. You cannot send documents stored in the Document Server
using the copy, printer, or scanner functions.
❒ The specified documents are sent with the scan settings made when they
were stored.
❒ To see details of the selected document, press [Details]. To return to the dis-
play in step , press [Exit].
B
❒ For the maximum number of stored documents you can specify at a time,
see “Maximum Values”.
❒ For the maximum number of stored pages you can send in one operation,
see “Maximum Values”.
Reference
p.278 “Maximum Values”
228
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Stored File
Specifying documents from [File List]
A Press [U] or [T] to display the documents to be sent.
B Select the file.
Specifying documents by [User Name]
A Select [User Name].
5
B Select the user name of the programmed document, and then press [OK].
To search by directly entering a user name, press [Manual Entry], and then enter
the user name. Partial matching is used when searching for a user name.
C Select the file to be sent.
229
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Document
Specifying documents by [File Name]
A Select [File Name].
B Enter the name of the document to be sent, and then press [OK].
5
Partial matching is used when searching for a file name.
C Select the file to be sent.
Displaying a preview
A Select the document you want to send.
Press the Thumbnail key to switch the screen to thumbnail display.
B Press [Preview].
230
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Stored File
C Check the preview.
• Press [Zoom Out] or [Zoom In] to reduce or enlarge the preview image.
• Press [←][→][↑][↓] to scroll the preview image.
• Press [Switch] for “Display File” to display another selected file.
• Press [Switch] for “Display Page” to change the displayed page.
D Press [Exit].
E Press [OK].
Note
5
❒ If image files are corrupt or are larger than A3, they are not displayed on
the preview window.
❒ If the image file is corrupt, store it again.
❒ If you stored originals that had multiple mixed-size pages without using
the Mixed Original Sizes function, the displayed size might differ from the
actual size for pages after the first page.
Printing Stored Documents
Use this function to print documents stored in the Document Server.
Important
❒ When [Print 1st Page] is selected, originals larger than A4 size are printed after
they are reduced to A4 size.
A Press [Select Stored File].
231
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Document
B Select the document to be printed.
Press the Thumbnail key to switch the screen to thumbnail display.
C If you select a document with a password, enter the password, and then
press [OK].
5
If the document does not have a password, proceed to step .
D
D Press [Print File] or [Print 1st Page].
When [Print File] is pressed, the machine prints all the pages. When [Print 1st
Page] is pressed, the machine prints only the first page.
To print both sides, press [Print 2 Sides]. When multiple files are specified they
are printed per file.
To cancel printing, press [Cancel].
E Press the {Start} key.
When only the first page is printed, the file name is printed at the top of the
paper.
To cancel printing after pressing the {Start} key, press [Stop Printing].
F Press [Cancel].
The standby display appears.
232
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Stored File
Note
❒ Only documents stored using the facsimile function can be printed.
❒ When printing originals that were not stored using the Mixed Original Siz-
es function, paper sizes might differ according to whether printing is
through the facsimile function or the Document Server.
❒ You can also print the first page only to check the content of the original.
❒ You can specify and print multiple documents at one time.
❒ For the maximum number of stored documents you can print at a time us-
ing [Print 1st Page], see “Maximum Values”.
❒ For the maximum number of stored pages you can print at a time, see
“Maximum Values”.
Reference
p.278 “Maximum Values”
Changing Stored Document Information
5
You can change the file name, user name, and password of stored documents.
To change a stored document, delete the document you no longer need, and then
reprogram the new document.
A Select [Select Stored File].
B Select [Manage / Delete File], and then press the document to be changed.
233
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Document
C If you select a document for which a password is set, enter the password,
and then press [OK].
When a selected file does not have a password, proceed to step .
D
D Change the desired information of the stored document.
Press the keys for the items you want to change.
5
E Press [Exit].
The standby display appears.
234
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Stored File
Changing a user name
A Press [Change User Name].
B Press [Clear].
5
The user name is deleted.
C Enter the new user name, and then press [OK].
Press the title word keys to switch between titles.
To set a non-programmed user name, press [Manual Entry], and then enter the
name.
User names entered by pressing [Manual Entry] are not programmed into the
user code.
Note
❒ Depending on the security settings, [Change Access Priv.] might be dis-
played instead of [Change User Name]. For details about setting [Change Ac-
cess Priv.], ask the administrator.
Reference
“Entering Text”, About This Machine
235
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Document
Changing the file name
A Press [Change File Name].
B Press [Backspace] or [Delete All], and then re-enter the file name.
5
C Press [OK].
Reference
“Entering Text” About This Machine
Changing the password
A Press [Change Password].
236
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Stored File
B Enter a new password using the number keys, and then press [OK].
C Enter the password again, and then press [OK].
5
Deleting a Stored Document
Use this function to delete stored documents.
A Press [Select Stored File].
237
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing a Document
B Press [Manage / Delete File].
C Select the document you want to delete.
5
You can also delete multiple documents at once.
D Enter a password using the number keys, and then press [OK].
E Press [Delete File].
F Press [Yes].
If you do not want to delete the document, press [No].
G Press [Exit].
The standby display appears.
238
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Fax via Computer
This section explains how to use this machine's facsimile function from a com-
puter via a network.
Sending Fax Documents from Computers
You can send a document created with a Windows application from a computer
connected to the machine to another fax machine.
Connect computers to the machine via parallel port, LAN, IEEE 802.11b (wire-
less LAN), IEEE 1394 (IPv4 over 1394), or USB 2.0.
• To send a fax, simply select [Print] from the Windows application, then select
LAN-Fax as the printer, and then specify a destination. LAN-Fax enables pa-
perless faxing from your computer to the other destinations.
• In addition to sending faxes, the LAN-Fax Driver allows this machine to be
used for printing out documents prepared on a computer for proof checking.
• To use the LAN-Fax Driver, connect this machine to a LAN and make the nec-
essary network settings, and then install the LAN-Fax Driver and the related
utilities on your computer.
ALT007S
Important
❒ Errors occurring when the machine is used as a LAN-Fax will not be dis-
played on the computer. Check for errors by using a Web Image Monitor. See
Web Image Monitor help.
❒ USB connection is not available when using the LAN-Fax function on Win-
dows 98.
❒ The facsimile function of this machine cannot be used with IPv6.
239
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
Note
❒ It is recommended that you use Web Image Monitor running under the same
network environment as this machine. Otherwise, the Web browser may not
open and an error may occur.
Before Use
To use these features, a LAN-Fax Driver must be installed on your computer.
Use the LAN-Fax Driver included on the scanner CD-ROM. You must also make
the required network settings on the machine, according to the type of connec-
tion.
Note
❒ When a personal computer and the machine are connected in parallel: See
“Preparing the Machine”, Printer Reference.
❒ When using Ethernet, IEEE 1394 (IPv4 over 1394), or IEEE 802.11b (wireless
LAN): See “Connecting the Machine”, General Settings Guide.
Reference
“Connecting the Machine”, General Settings Guide
6
“System Settings”, General Settings Guide
“Preparing the Machine”, Printer Reference
Using the Software
This section provides information about LAN-Fax Driver, Address Book, and
LAN-Fax Cover Sheet Editor.
LAN-Fax Driver
This driver allows you to use LAN-Fax functions.
Important
❒ All operations cannot be guaranteed depending on the system environment.
❒ When you use Windows NT, LAN-Fax Driver will not work in an RISC base
processor (MIPS R series, Alpha AXP, PowerPC) environment.
❖ Location of the file
The following folders are on the CD-ROM:
• LAN-Fax Driver for Windows 98/Me
\DRIVERS\LAN-FAX\WIN9X_ME
• LAN-Fax Driver for Windows NT 4.0
\DRIVERS\LAN-FAX\NT4
• LAN-Fax Driver for Windows 2000/XP and Windows Server 2003
\DRIVERS\LAN-FAX\WIN2K_XP
240
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending Fax Documents from Computers
❖ Operating environment
• Computer
PC/AT compatible
• Operating systems
Microsoft Windows 98/Me
Microsoft Windows 2000/XP
Microsoft Windows Server 2003
Microsoft Windows NT 4.0
• Display
VGA 640×480 pixels or more
Note
❒ Before beginning installation, exit all other applications.
Address Book
Address Book helps you edit LAN-Fax transmission destinations.
❖ Operating systems
Microsoft Windows 98/Me
Microsoft Windows 2000/XP
Microsoft Windows Server 2003
Microsoft Windows NT 4.0
6
LAN-Fax Cover Sheet Editor
LAN-Fax Cover Sheet Editor helps you edit LAN-Fax cover sheets.
❖ Operating systems
Microsoft Windows 98/Me
Microsoft Windows 2000/XP
Microsoft Windows Server 2003
Microsoft Windows NT 4.0
241
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
Auto Run program
The installers for various drivers and utilities launch automatically as Auto Run
programs when you insert the CD-ROM.
LAN-Fax Driver, Address Book, and LAN-Fax Cover Sheet Editor can be in-
stalled by Auto Run.
Important
❒ If the plug and play function starts, click [Cancel] in the [New Hardware Found],
[Device Driver Wizard], or [Found New Hardware Wizard] dialog box, and then in-
sert the CD-ROM. The [New Hardware Found], [Device Driver Wizard], or [Found
New Hardware Wizard] dialog box appears depending on the system version of
Windows 98/Me, Windows 2000/XP, Windows Server 2003, or Windows NT
4.0.
❒ Auto Run might not work automatically with certain OS settings. If this is the
case, double-click “Setup.exe”, located on the CD-ROM root directory.
❒ If you want to cancel Auto Run, hold down the {SHIFT} key (when your sys-
tem is Windows 2000/Windows XP or Windows Server 2003, hold down the
left {SHIFT} key) while inserting the CD-ROM. Keep the {SHIFT} key held
down until the computer stops reading the CD-ROM.
6
❒ Clicking [Cancel] during installation aborts the installation. If you cancel the
installation, restart your computer and install the rest of the software or print-
er driver.
Note
❒ If your operating system is Windows 2000/XP, Windows Server 2003 or Win-
dows NT 4.0, installing a printer driver using Auto Run requires Administra-
tor permissions. When you install LAN-Fax Driver using Auto Run, log on
using an account that has Administrator permissions.
Installing Individual Applications
You need to install a LAN-Fax Driver on your computer before using the LAN-
Fax functions. The LAN-Fax Driver is on the CD-ROM included with this ma-
chine.
Address Book and LAN-Fax Cover Sheet Editor are installed with the LAN-Fax
Driver. Address Book helps you edit LAN-Fax transmission destinations. LAN-
Fax Cover Sheet Editor helps you edit LAN-Fax cover sheets.
Use the following procedure to install LAN-Fax Driver, Address Book, and
LAN-Fax Cover Sheet Editor at one time.
Important
❒ Before installing the above applications, install SmartDeviceMonitor for Cli-
ent.
242
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending Fax Documents from Computers
A Quit all applications currently running.
B Insert the CD-ROM included with this machine into the CD-ROM drive of
your computer.
The installer launches automatically, and the language selection window ap-
pears.
Depending on your operating system settings, the installer may not launch
automatically. If it does not, double-click “Setup.exe” in the CD-ROM root di-
rectory to launch the installer.
C Select the interface language of the software, and then click [OK].
D Click [LAN-Fax Driver].
The software license agreement window appears.
E Read all of the terms and, if you agree, select [I accept the agreement.], and
then click [Next].
If you select [I don't accept the agreement.], you cannot complete the installation.
F Select the [LAN-Fax Driver] check box, and then click [Next].
6
G Confirm that the [Printer Name:<LAN-Fax M8>] check box is selected, and then
click [Continue].
Select the desired port.
H Click [Finish].
The installation completion dialog box appears.
I Click [Finish].
J Click [Exit].
Setting LAN-Fax Driver Properties
This section explains how to set properties required for using the LAN-Fax Driv-
er.
Note
❒ If your operating system is Windows NT 4.0, Windows 2000/XP, or Windows
Server 2003, log on using an account that has Administrator rights.
243
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
Setting print properties
This section explains how to make settings such as paper size or resolution.
A On the [Start] menu, point to [Settings], and then click [Printers].
With Windows XP Professional or Windows Server 2003, select [Printers and
Faxes] on the [Start] menu.
With Windows XP Home Edition, select [Control Panel] on the [Start] menu.
Next select [Printers and Other Hardware], and then [Printers and Faxes].
B Select to highlight [LAN-Fax M8], then click [Properties] on the [File] menu.
With Windows NT, click [Document Defaults...] on the [File] menu.
C When using Windows 98/Me, click the [Paper] tab to set the following prop-
erties.
• Paper Size
• Orientation
• Tray
• Resolution
• Gray Scale
• Print as Graphics
6
D When using Windows NT 4.0, set the following properties.
• Paper Size
• Orientation
• Tray
• Resolution
E When using Windows 2000/XP or Windows Server 2003, click the [Printing
Preferences...] button to set the following properties.
• Paper Size
• Orientation
• Tray
• Resolution
F Click [OK].
244
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending Fax Documents from Computers
Making settings for option configuration
Make settings for optional units installed in this machine.
A On the [Start] menu, point to [Settings], and then click [Printers].
With Windows XP Professional or Windows Server 2003, select [Printers and
Faxes] on the [Start] menu.
With Windows XP Home Edition, select [Control Panel] on the [Start] menu.
Next select [Printers and Other Hardware], and then [Printers and Faxes].
B Select to highlight [LAN-Fax M8], then click [Properties] on the [File] menu.
C Click the [Accessories] tab, and then make the settings for the option config-
uration.
D When the machine is connected to a network, option configuration is auto-
matically performed. If the settings do not match the installed optional
units, click [Load from Device].
E When this machine is connected locally to your computer, select the check
boxes for the installed optional units.
6
F Click [Apply].
Option configuration settings are complete.
G Click [OK].
[Accessories] tab
The [Accessories] tab contains the following items besides option configura-
tion items.
• Prohibit manual destination entry
Check this option to inhibit direct destination specification.
• Enable E-mail
Check this when using Internet Fax with the LAN-Fax function.
• IP-Fax
Check this option when using IP-Fax.
After checking this option, select a protocol by clicking an appropriate ra-
dio button.
Note
❒ If the options on this machine are not configured as instructed, LAN-Fax
functions may fail.
❒ When this machine is connected to a network and the port is set via the
“SmartDeviceMonitor for Client” port, option configuration is automati-
cally performed. For details about automatic option configuration, see
LAN-Fax Deriver's Help.
245
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
Basic Transmission
This section explains how to send fax documents created using Windows appli-
cations.
To send a fax, simply select [Print...] from the Windows application, then select
[LAN-Fax M8] as the printer, and then specify a destination in the [LAN-Fax] dialog
box.
Open the application document you want to send or create a new document, and
then perform the following procedure.
For details, see LAN-Fax Driver's Help.
Important
❒ When using SmartDeviceMonitor for Client, you cannot send documents to
this machine using more than one LAN-Fax at the same time.
A On the [File] menu, click [Print...].
B Select [LAN-Fax M8] in the [Name:] list.
C Click [OK].
6
The LAN-Fax dialog box appears.
The setting method may differ depending on the application you are using.
In all cases, select [LAN-Fax M8] for the printer.
D Specify the destination.
For details about specifying a destination, see the LAN-Fax Driver's Help.
When user authentication is used with this machine, click [User Settings...].
E Specify necessary options.
F Click [Send].
When you click [Send & Print], the fax is sent to the destination and your ma-
chine prints a copy of the document you sent.
Note
❒ The machine can retain documents sent from a LAN-Fax Driver as files to
be sent. For the maximum number of documents the machine can retain,
see “Maximum Values”.
❒ For the maximum number of destinations you can specify per file, see
“Maximum Values”.
246
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending Fax Documents from Computers
Fax Destination, or IP-Fax destination”
p.249 “Specifying Options”
p.254 “Editing Address Book”
p.278 “Maximum Values”
Specifying a destination using a destination list
A Click the [Address Book] or [Specify Destination] tab.
The [Address Book] or [Specify Destination] tab appears.
B Select the [Device Address] (or [Use device address]) check box.
C The machine's address is displayed in the [Device Address] field on the [Ad-
dress Book] tab. On the [Specify Destination] tab, enter the registration number
of the Destination key in the [Device Address] box.
6
D Click [Set as Destination].
The entered destination is added and appears in the [List of Destination:] box.
click [Delete from List].
E To specify more destinations, repeat steps and .
C
D
Specifying a destination using Address Book
Important
❒ In order to use this method, you need to register destinations in the address
list using Address Book.
A Click the [Address Book] tab.
The [Address Book] tab appears.
B Select a CSV file containing the desired destination list, from the [Address
Book:] dropdown menu.
Up to the three most recently used files appear in the dropdown menu. To use
a destination list that did not appear, click [Browse...], and then select the file.
247
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
C
Select
[
Contact
]
or
[
Group
]
in the [Name:] dropdown menu as the display format.
Destination list contents change as follows, depending on the option selected:
• Group: Group name
If you selected [Group], proceed to step .
E
D If you selected [Contact] in step , select the type of fax from the [Type:]
C
dropdown menu.
To send by standard fax or IP-Fax, select [Fax]. To send by Internet Fax, select
[E-mail].
E Click the destination in the destination list to highlight it, and then click
[Set as Destination].
The selected destination is added and appears in the [List of Destination:] box.
If you add a destination by mistake, click the wrong destination, and then
click [Delete from List].
You can then jump to the name you entered.
6
F To specify more destinations, repeat steps through .
B
E
Note
❒ Destination list contents can be narrowed down by selecting the first letter
of a contact name, company name or group name in the [Search] dropdown
menu.
Specifying a destination by directly entering a fax number, Internet Fax Destination, or
IP-Fax destination
A Click the [Specify Destination] tab.
The [Specify Destination] tab appears.
B Select the type of fax from the [Type:] dropdown menu.
To send by standard fax or IP-Fax, select [Fax]. To send by Internet Fax, select
[E-mail].
After you select the fax type, the items corresponding to the selected type ap-
pear.
C Specify the destination.
Specify the destination depending on the selected fax type as follows:
• If you selected [Fax]: enter the fax number. To send by IP-Fax, enter the IP-
Fax destination.
To enter a pause in the fax number, click [Pause]. If you selected [E-mail] in step
, [Pause] is not available.
B
248
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending Fax Documents from Computers
D Specify settings according to the type of fax transmission.
Specify settings according to the type of fax transmission selected in step ,
B
as follows:
• If you selected [Fax], select a line or a protocol in the [Line:] list.
• If you selected [E-mail], select the [Do not use SMTP server] check box if you
want to bypass the SMTP server.
E Click [Set as Destination].
The entered destination is added and appears in the [List of Destination:] box.
click [Delete from List].
F To specify more destinations, repeat steps through .
B
E
Note
❒ For the maximum number of digits for a destination, see “Maximum Val-
ues”.
6
p.67 “Sending by IP-Fax”
p.70 “Sending to an E-mail Address”
p.278 “Maximum Values”
Specifying Options
You can specify the following transmission options when sending a fax.
For details about transmission options, see the LAN-Fax Driver's Help.
• Sending at specific time
• Print Fax Header
• Attach a Cover Sheet
• 2 sided printing
• Preview
• Save as file
• Document Server
To send a fax document at a specific time
A Click [Send Options].
The [Send Options] tab appears.
B Select the [Sending at specific time] check box, and then specify a transmission
time.
249
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
To print a sender stamp
A Click [Send Options].
The [Send Options] tab appears.
B Select the [Print Fax Header] check box.
To attach a cover sheet
A Click [Send Options].
The [Send Options] tab appears.
B Select the [Attach a Cover Sheet] check box.
A cover sheet is added to the first page of a transmission file.
Reference
p.258 “Editing Fax Cover Sheets”
6
To specify two-sided printing
A Click [Send Options].
The [Send Options] tab appears.
B Select the [2 sided printing] check box.
To display preview
Selecting the [Preview] check box allows you to check how the fax document will
be output at the destination.
A Click [Send Options].
The [Send Options] tab appears.
B Select the [Preview] check box.
C Click [Send] or [Send & Print].
The [Preview] window appears.
D Click [Next] or [Previous] to check the image.
To close the [Preview] window, click [Cancel].
250
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending Fax Documents from Computers
Saving as files
You can save the fax document in TIFF format (TIFF-F).
A Click [Send Options].
The [Send Options] tab appears.
B Select the [Save as file] check box.
C Click [Save to...].
D Select a folder on the folder tree.
E Select a method of file naming.
To enter a file name manually, select the [Specify file name when saving] check
box. To have the file assigned a name and saved automatically, select the [Au-
tomatically create a new file] check box.
F Click [OK].
G Click [Save] or [Save & Send].
If you select [Automatically create a new file], the image file is assigned a name
and saved under the specified folder.
6
The file name will be RicHHMMSS.tif (HH: hours, MM: minutes, SS: sec-
onds).
H Enter a file name.
You can also change the folder in this step.
I Click [Save].
The image file is saved in the specified folder.
Note
❒ Single-page documents are saved as single TIFF files, and multiple-page
documents are saved as multiple TIFF files.
To store the fax document on the Document Server
Important
❒ If [Hard Disk Unit] is not selected in [Accessories] on the printer properties dia-
log box, you cannot select [Document Server].
A Click [Send Options].
The [Send Options] tab appears.
B Select the [Send to Document Server] check box, and then enter a user name,
file name, and password.
251
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
Checking Transmission Using LAN-Fax Driver
From “SmartDeviceMonitor for Admin”, “SmartDeviceMonitor for Client”, or
Web Image Monitor, you can check information about files sent using LAN-Fax
Driver. For the maximum number of transmission results you can check, see
“Maximum Values”.
Also, you can save the contents of the Journal in a personal computer as a CSV
file using [Load Fax Journal] in “SmartDeviceMonitor for Admin”.
Note
❒
When data is transmitted from the LAN-Fax Driver via the “SmartDeviceMoni-
tor for Client” port, the “Data-transmission complete.” message appears on
the computer's display, so you can easily ascertain the communication progress.
However, if the volume of communication data from the LAN-Fax to this ma-
chine increases, the message may appear during the operation, due to the differ-
ences in memory capacity between this machine and “SmartDeviceMonitor for
Client”. For more accurate fax transmission results, use “E-mail TX results”.
❒ The job history may differ from the machine's transmission results. In that
case, refer to the machine's transmission results.
6
p.194 “Communication Result Report (Memory Transmission)”
p.278 “Maximum Values”
Confirming Transmission Results by E-mail
After communicating in the LAN-Fax mode, this function transmits the commu-
nication results with the computer by e-mail.
When you have done [Send] or [Send & Print] using the LAN-Fax, and when the
communication was successful, it transmits e-mail of the transmission result.
Result notification e-mail is sent when printing is complete, or if an error occurs
during communication between this machine and a computer.
A Click the [E-mail Settings] tab.
B Select the [Notify] check box under [E-mail TX results].
C Enter the destination.
When entering the e-mail address directly, click the [Specify destinations] radio
button, and then enter the e-mail address in the [Specify destinations] field.
When entering the machine's programmed address, click the [Device Address]
radio button, and then enter the registration number of the Destination key in
the [Device Address] box.
The [Device Address] box is unavailable when the [Specify destinations] is select-
ed, and you cannot enter anything in the text box.
252
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending Fax Documents from Computers
D Click [Send] or [Send & Print].
Note
❒ You can confirm transmission results using the E-mail TX Results function
and the Communication Result Report. You can set whether to use both of
these together in User Parameters (switch 10, bit 6) in the Facsimile Fea-
tures menu.
❒ If there be any insufficient configurations in the e-mail menu on this ma-
chine, or if “Auto Specify Sender Name” is set to “Off”, the LAN-Fax result
notification e-mail is not transmitted, and the LAN-Fax Result Report is
printed. See “System Settings”, General Settings Guide for the e-mail set-
p.194 “Communication Result Report (Memory Transmission)”
p.253 “LAN-Fax Result Report”
“System Settings”, General Settings Guide
“Facsimile Features”, General Settings Guide
6
LAN-Fax Result Report
This section explains the LAN-Fax Result Report.
If “E-mail TX results” is set to “Notify”, if there be any insufficient configura-
tions in the e-mail menu on this machine, or if “Auto Specify Sender Name” is
set to “Off”, the LAN-Fax result notification e-mail is not transmitted, and the
LAN-Fax Result Report is printed. If the “E-mail TX Results” of “Sender Name”
has not been set to on, the LAN-Fax Result Report is printed.
Note
❒ Whether or not the LAN-Fax Result Report is printed, can be configured with
User Parameters (Switch 20, bit 0) in the Facsimile Features menu.
❒ When executing [Send] or [Send & Print] with the LAN-Fax Driver, and when
the E-mail TX Result Report has not arrived, the Communication Result Re-
Reference
p.194 “Communication Result Report (Memory Transmission)”
“Facsimile Features”, General Settings Guide
253
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
Printing and Saving
You can print documents created using Windows applications.
Open the application document you want to print or create a new document,
and then perform the following procedure.
For details about printing the fax image, see the LAN-Fax Driver's Help.
A On the [File] menu, click [Print...].
B Select [LAN-Fax M8] in the [Name:] list, and then click [OK].
The [LAN-Fax] dialog box appears.
The setting method may differ depending on the application you are using.
In all cases, select [LAN-Fax M8] for the printer.
C Click [Print] or [Send & Print].
You can save the fax image in a file. See “Specifying Options”.
Note
❒ You can also save documents in TIFF format. For details about saving in
TIFF format, see “Saving as files”.
6
❒ You can select the length of time the machine keeps document data in
memory if print fails due to problems such as a paper shortage or paper
jams. Make this setting with User Parameters (switch 20, bit 2, 3, 4, 5) in the
Facsimile Features menu. Date is deleted when the specified length of time
elapses.
p.249 “Specifying Options”
p.251 “Saving as files”
“Facsimile Features”, General Settings Guide
Editing Address Book
You can program and edit destinations in the address list using the Address
Book.
For details about the Address Book, see the LAN-Fax Driver's Help.
Note
❒ You can use files created in CSV format as Address Book data. For this pur-
pose, create CSV files that conform to a certain format. For more information,
see Help.
254
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending Fax Documents from Computers
Programming new destinations
A On the [Start] menu, point to [Programs], [LAN-Fax Utilities], and then click [Ad-
dress Book].
The [Address Book] dialog box appears.
If LAN-Fax Driver has already started up, click [Edit Address Book...].
B Click [New/Browse...], and then select the CSV file containing the address list
to be edited.
C Enter the destination and name.
You can enter a contact name, company name, department name, fax num-
ber, e-mail address, and IP-Fax address. The name and destination (Fax Num-
ber, E-mail address or IP-Fax address) cannot be omitted.
D Click [Add].
The destination is added to the destination list.
E Click [Close].
F If you made changes to a destination, a confirmation message appears. To
save the changes, click [Yes].
6
If you do not want to save the changes and want to quit editing, click [No].
To return to the editing display, click [Cancel].
The confirmation dialog box does not appear when you have not made any
changes after starting Address Book.
Note
❒ To program the contents of the destination list of this machine to the Ad-
dress Book, select the [Use device address] check box, then enter the Desti-
nation key's registration number in the [Device Address] field.
❒ For [Line:] under [Fax Number:], the following line types are selectable; G3,
G3-2, G3-3, G4, G3 Dir. Auto, G3 PABX Auto, or I-G3. However, this ma-
chine does not support G4 and G3 PABX Auto.
❒ For [Protocol:] under [IP-Fax address:], select [H.323] or [SIP].
❒ To bypass the SMTP server, under the [E-mail address:] box, select the [Do
not use SMTP server] check box.
255
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
Editing programmed destinations
A On the [Start] menu, point to [Programs], [LAN-Fax Utilities], and then click [Ad-
dress Book].
The [Address Book] dialog box appears.
If LAN-Fax Driver has already started up, click [Edit Address Book...].
B Click [New/Browse...], and then select the CSV file containing the address list
to be edited.
C Select the destination you want to edit so it is highlighted in the list.
D Edit the data.
E Click [Update].
F Click [Close].
G If you made changes to a destination, a confirmation message appears. To
save the changes, click [Yes].
If you do not want to save the changes and want to quit editing, click [No].
To return to the editing display, click [Cancel].
6
The confirmation dialog box does not appear when you have not made any
changes after starting Address Book.
Deleting programmed destinations
A On the [Start] menu, point to [Programs], [LAN-Fax Utilities], and then click [Ad-
dress Book].
The [Address Book] dialog box appears.
If LAN-Fax Driver has already started up, click [Edit Address Book...].
B Click [New/Browse...], and then select the CSV file containing the address list
to be edited.
C Select the destination you want to delete so it is highlighted in the list.
D Click [Delete].
E Click [Yes].
F Click [Close].
256
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending Fax Documents from Computers
G If you made changes to a destination, a confirmation message appears. To
save the changes, click [Yes].
If you do not want to save the changes and want to quit editing, click [No].
To return to the editing display, click [Cancel].
The confirmation dialog box does not appear when you have not made any
changes after starting Address Book.
Using the Machine's Address Book Data in the Destination List of
the LAN-Fax
You can save information about fax destinations registered to this machine in a
personal computer as a CSV file using “Address Management Tool” in “Smart-
DeviceMonitor for Admin”. Saved CSV files can be inserted into the destination
table of the LAN-Fax Driver by selecting [New/Browse...] in Address Book. Save
the file again for the LAN-Fax Driver.
Note
❒ When destinations registered in groups by this machine are inserted into Ad-
dress Book, each person's destination is determined according to the follow-
ing order of priority (check before inserting and changing the order of
priority, if necessary): IP-Fax destination → Fax number → Mail address
6
❒ Depending on the machine type, you may not be able to use the machine
when it is updating the Address Book using CSV files (retrieved using Smart-
DeviceMonitor for Admin) that contain user codes.
❒ For details, see “SmartDeviceMonitor for Admin” Help.
257
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
Editing Fax Cover Sheets
LAN-Fax Cover Sheet Editor allows you to edit the format for fax cover sheets.
Important
❒ It is necessary to create a cover sheet file before attaching a cover sheet to fax
document using LAN-Fax Driver.
Creating a cover sheet
Use the following procedure to create a fax cover sheet.
You can edit the following items using LAN-Fax Cover Sheet Editor.
• Company name as destination information
• Department name as destination information
• Person name as destination information
• Company name as sender information
• Department name as sender information
• Person name as sender information
• Telephone number as sender information
• Fax number as sender information
• Date
6
• Message
A On the [Start] menu, point to [Programs], [LAN-Fax Utilities], and then click
[LAN-Fax Cover Sheet Editor].
The [LAN-Fax Cover Sheet Editor] dialog box appears.
B Edit the cover sheet.
For details about operations, see Help.
C Click [Save as...] on the [File] menu.
D Select a folder, and then enter a file name.
E Click [Save].
Note
❒ Cover sheet data is stored in its own format (using “fcp” as its extension).
258
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending Fax Documents from Computers
Attaching a created cover sheet
Use the following procedure to attach a created cover sheet file to a fax docu-
ment.
A On the [File] menu, click [Print...].
B Select [LAN-Fax M8] in the [Name:] list, and then click [OK].
The [LAN-Fax] dialog box appears.
C Click [Edit Cover Sheet...].
The [Cover Sheet] dialog box appears.
D Select a cover sheet file from the dropdown list or after clicking [Browse...]
in [Select Cover Sheet].
other file. If you want to change only destination information, omit this step
and proceed to step .
E
E Select the type of information from [To:].
You can select [Use Address Book], [To Whom It May Concern], [Edit Names], or
[(None)]. Selecting [Edit Names] allows you to enter company, department, and
person names.
6
F To print the date, select the [With a Date] check box.
G Enter the sender information.
You can enter company, department, and contact names, and telephone and
fax numbers.
To add a message, select the [With a Message] check box, and then enter a mes-
sage.
H Click [OK].
I Specify a destination.
J Click the [Send Options] tab, and then select the [Attach a Cover Sheet] check
box.
K Click [Send] or [Send & Print].
259
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
Managing Facsimile Functions Using SmartDeviceMonitor for
Admin
You can check information about this machine's fax functions using a computer
and save files on a computer using SmartDeviceMonitor for Admin.
Note
❒ For details about SmartDeviceMonitor for Admin and its installation, see
“Monitoring and Configuring the Printer”, Network Guide.
❒ For details, see Network Guide and SmartDeviceMonitor for Admin Help.
Reference
“Monitoring and Configuring the Printer”, Network Guide
LAN-Fax Operation Messages
This section explains typical operation error messages displayed on the comput-
er when using the LAN-Fax Driver, and solutions to those messages.
Message
Causes and Solutions
6
Check the network connection.
Cannot connect to the de-
vice.
Check that the power is turned on.
The number of destinations specified exceeds the
maximum possible. The maximum number of desti-
nations that can be specified at one time is 500.
The number of entries in
Destinations exceed the
limits. Up to 500 entries
can be entered.
The [LAN-Fax] dialog box is already open. Quit LAN-
Fax once, and then start it up again.
"LAN-Fax" has already been
launched. Cannot launch it
again.
Available memory on the computer is insufficient.
Quit applications currently not in use.
Failed to allocate memory.
260
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Fax Information Using a Web Browser
Viewing Fax Information Using a Web
Browser
You can view received fax documents and their lists or print these documents
using a Web Image Monitor on a network computer.
Note
❒ It is recommended that you use a Web Image Monitor running under the
same network environment as this machine. Otherwise, the Web browser
may not open and an error may occur.
❒ You need to select “Store” as the “Reception File Setting” in the Facsimile Fea-
tures menu.
❒ You can also check and manage the documents using DeskTopBinder.
Reference
“Monitoring and Configuring the Printer”, Network Guide
“Facsimile Features”, General Settings Guide
DeskTopBinder's manual and Help
6
Viewing, Printing, and Deleting Received Fax Documents Using a
Web Image Monitor
Use the following procedure to view and/or print received fax documents using
a Web Image Monitor.
Viewing received fax documents using a Web browser
A Start a Web browser.
B Enter the machine's IPv4 address in the [Address] field.
C Click [Fax Received File] in the left pane.
D If you have programmed a user code for the stored reception file, enter the
code, and then press [OK].
A list of the received fax documents appears.
If the programmed user code was deleted using the Address Book Manage-
ment function under System Settings, a message indicating incorrect user
code entry appears. If this is the case, reprogram a user code.
E Click of the desired fax document.
To view a list of the fax documents, select the thumbnail display, icon display,
or detail display. Click
,
, or
.
261
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
F View the content of the fax document.
To enlarge the preview image, click [Enlarge Image]. Enlargement cannot be
performed without Acrobat Reader installed. For more information, see Help
on the Web Image Monitor.
G To download the received fax document, click [PDF] or [Multi-page TIFF], and
then click [Download].
A downloading confirmation dialog box appears.
When you select [PDF], make the necessary “PDF File Security Settings” be-
fore clicking [Download]. Acrobat Reader starts and the selected document is
displayed.
Note
❒ If your computer cannot be connected to Web Image Monitor, see Network
Guide.
❒ To download the document data on the list of received fax documents,
click [TIFF] or [PDF]. For details about downloading, see the Web Image
Monitor Help.
❒ The method for downloading differs depending on the selected format.
For more information, see Help on the Web Image Monitor.
6
Reference
Network Guide
Printing fax information using a Web browser
A Start a Web browser.
B Enter the machine's IPv4 address in the [Address] field.
C Click [Fax Received File] in the left pane.
The list of received fax documents appears.
D Select the check box of the fax document to be printed.
To view a list of the fax documents, select the thumbnail display, icon display,
or detail display. Click
,
, or
.
E Click [Print].
F Click [Print].
To cancel printing, press [Cancel] before clicking [Print].
You can change the printing order of selected multiple documents. You can
also have documents printed on both sides of the paper. For more informa-
tion, see Help on the Web Image Monitor.
G Click [OK].
The display returns to that of step .
E
262
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Fax Information Using a Web Browser
Deleting fax information using a Web browser
A Start a Web browser.
B Enter the machine's IPv4 address in the [Address] field.
C Click [Fax Received File] in the left pane.
The list of received fax documents appears.
D Select the check box of the fax document to be deleted.
To view a list of the fax documents, select the thumbnail display, icon display,
or detail display. Click
,
, or
.
E Click [Delete].
F Click [Delete File(s)].
To cancel deletion, press [Cancel] before clicking [Delete File(s)].
After selecting multiple documents, you can also cancel deletion of some of
the selected documents. For more information, see Help on the Web Image
Monitor.
6
G Click [OK].
The display returns to that of step .
E
Programming Destination Information from Web Browser
If the receiving machine is compliant with T.37 full mode Internet Fax, you can
program the receiver's properties from Web Image Monitor. You can program
the following properties:
• Compression Type
• Paper size
• Resolution
Note
❒ For a detailed description, see Help for Web Image Monitor.
❒ When a receiver that is programmed as full mode in the Address Book re-
turns a Reception Notice e-mail, the contents of the newly received e-mail
Reference
p.33 “T.37 Full Mode”
263
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
To edit machine properties already programmed
Follow these steps to use Web Image Monitor to edit information about the des-
tination machine registered in the Address Book.
A Start the Web browser.
B Enter the IPv4 address of the machine you want to monitor after “http://” in
the address field.
The top screen is displayed.
C Click [Login], and then enter the Administrator's name and password.
D Click [Address Book] in the left pane.
The Address Book is displayed.
E Click the radio button to the left of the machine you want to modify, and
then click [Change].
The [Change User] page appears.
F Set the properties for Internet Fax data format other than the mode selec-
6
tion.
If you change the mode to “Simple Mode”, you cannot set machine proper-
ties.
G Click [OK] at the upper-left of the screen.
To cancel the setting, click [Cancel] in the upper-left of the screen.
The Address Book is displayed.
H Close the Web browser.
264
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Fax Information Using a Web Browser
To add new receiver
Follow these steps to use Web Image Monitor to add a new destination to the
Address Book.
A Start the Web browser.
B Enter the IPv4 address of the machine you want to monitor after “http://” in
the address field.
The top screen is displayed.
C Click [Login], and then enter the Administrator's name and password.
D Click [Address Book] in the left pane.
The Address Book is displayed.
E Click [Add User].
The [Add User] page appears.
F Enter the registration number, name, and e-mail address, then set the nec-
essary properties.
6
You can set the Internet Fax data format after entering the e-mail address.
G Click [Full Mode] under [Internet Fax Data Format], and set the properties ac-
cording to the receiver's properties.
If you change the mode to “Simple Mode”, you cannot set machine proper-
ties.
H Click [OK] in the upper-left of the screen.
To cancel the setting, click [Cancel] in the upper-left of the screen.
The Address Book is displayed.
I Close the Web browser.
265
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax via Computer
Delivering Files Received by Fax
Documents received by the machine can be viewed on or downloaded to a com-
puter using the network delivery server ScanRouter delivery software. This is a
useful function, enabling you to view and store documents on your computer
without printing them.
Important
❒ The ScanRouter delivery software is required as a delivery server. DeskTop-
Binder must be installed on your computer.
Using the delivery server, you can eliminate the task of retrieving and delivering
documents.
❖ Functions
Delivery server provides the following functions:
• Use the delivery server to associate incoming documents (SUB Code, Own
Name, and Own Fax Number) with receivers, so documents are delivered
to the intended receivers.
• You can select the delivery method for incoming documents: “Save in the
delivery server inbox”, “Send as an e-mail attachment”, or “Save in the
designated folder on the computer”. Incoming documents with no SUB
Code, Own Name, or Own Fax Number are saved in the delivery server
inbox. You can also set it so that the received documents are stored in the
specified delivery server inbox according to the line used for reception.
6
• You can check or download received documents stored in the delivery
server inbox using DeskTopBinder.
Note
❒ Documents received in Personal Boxes are also forwarded to the delivery
server.
❒ To view or download documents stored in the delivery server inbox, you
need to install DeskTopBinder on your computer.
❒ To send received documents to your computer as e-mail attachments, your
computer must have an e-mail application that is compatible with the Scan-
Router delivery software.
❒ To create a network using the delivery server, settings must be specified in
the User Tools of the machine. Settings must also be specified on the delivery
server.
❒ For details about the delivery server (ScanRouter delivery software), see the
ScanRouter delivery software's Help or instructions.
❒ For information about DeskTopBinder, see DeskTopBinder's manual and
Help.
Reference
“System Settings”, General Settings Guide
DeskTopBinder's manual and Help
266
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
This section explains features and specifications of the facsimile function.
Checking the Memory Status
Use this function to display a summary of current memory usage.
On the standby display you can check the percentage of free memory space. In
addition, in [System Status] you can check the number of “Transmission Standby
File(s)”, “Memory Lock File(s)”, and “RX Print Standby File(s)”. “Others” shows
the total number of documents registered in Information Boxes and received in
Personal Boxes. See “When the Machine Dose Not Operate as Wanted”, Trou-
bleshooting.
Note
❒ If you set the “Reception File Setting” in the Facsimile Features menu to
“Store”, you can check the number of received documents using “RX Print
p.211 “Personal Boxes”
p.214 “Information Boxes”
“Facsimile Features”, General Settings Guide
“When the Machine Dose Not Operate as Wanted”, Troubleshooting
267
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Programs
If you regularly send documents to a particular destination or transmit using the
same functions, you can save repetitive number keys operations by registering
this information in a Keystroke Program. Programs can be recalled by just press-
ing a programmed key.
Registering and Changing Keystroke Programs
The following procedure can be used to program a new Keystroke Program or
overwrite an old one.
You can register the following items in Keystroke Programs:
• Memory Transmission, Immediate Transmission, type of transmission, desti-
nations, Scan Type, Resolution, Scan Size, Mixed Original Sizes, Auto Densi-
ty, Manual Density, Original Orientation, Original Settings, Stamp, Select
Line, SUB/SID/SEP/PWD Code entry, Send Later, Reception Notice, BCC
Transmission, E-mail TX Results, Text, Standard Message, Auto Reduce, La-
bel Insertion, Closed Network, SUB Code Transmission, SEP Code Reception,
Fax Header Print, TX Status Report, Store File, PIN Code TX
• Program name
A Make the settings you want to register in the program.
7
The procedure for programming differs depending on the items you want to
register.
Press the {Clear Modes} key to cancel programming.
To register a program using Send Later with the fax number “0123456789”,
press {0}, {1}, {2}, {3}, {4}, {5}, {6}, {7}, {8}, {9} using the number keys, and
then continue doing the Send Later setting until the standby display appears
when you press [OK].
B Make sure that the machine is in facsimile mode and the standby display
is shown.
If the standby display is not shown, press the {Facsimile} key.
C Press the {Program} key.
ALV019S
268
Download from Www.Somanuals.com. All Manuals Search And Download.
Programs
D Press [Program].
When no programs are registered, proceed to step .
E
E Select a program number in which “Not Programmed” is shown.
If you make a mistake, press [Cancel] and select a program number again.
Yes
When you change a Keystroke Program, press
[
]
after pressing the program
No and return to step .
E
number you want to change. If you make a mistake, press
[
]
F Enter the program name, and then press [OK].
If you make a mistake, press [Backspace] or [Delete All], and then try again.
You should register the program name.
To cancel a program, press [Cancel]. The display returns to that of step .
E
G Press [Exit].
The standby display appears.
Note
❒ Use the same procedure to register and change programs. In step , select
E
the program number you want to change.
❒ For the maximum number of Keystroke Programs you can register, see
“Maximum Values”.
❒ For the maximum number of characters you can enter for a program name,
see “Maximum Values”.
❒ For the maximum number of destinations you can register to a Keystroke
Program, see “Maximum Values”.
❒ The method of registering or changing programs for the copy function is
different from that of the fax function.
269
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
p.123 “Sending at a Specific Time (Send Later)”
p.278 “Maximum Values”
“Entering Text”, About This Machine
Registering a priority function using a program
Set the functions registered in a program as priority functions, so you can have
the machine select these functions right after the power is turned on or the {Clear
Modes} key is pressed.
To set the priority functions, register the desired settings to a program. Then, re-
call the registered program, and then press [Program as Defaults] on the Program
screen. The recalled settings are registered as priority functions.
7
Important
❒ Destinations and SUB/SID/SEP/PWD Code entries cannot be registered as
priority functions.
Reference
“Facsimile Features”, General Settings Guide
270
Download from Www.Somanuals.com. All Manuals Search And Download.
Programs
Changing a program name
Follow these steps to change a program name.
A Make sure that the machine is in facsimile mode and the standby display
is shown.
If the standby display is not shown, press the {Facsimile} key.
B Press the {Program} key.
ALV019S
C Press [Change Name].
7
D Select the program number of the name you want to change.
E Enter a new program name, and then press [OK].
Press [Cancel] to cancel the change, and proceed to step .
F
F Press [Exit].
The standby display appears.
271
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Deleting a Program
Follow these steps to delete an unnecessary program:
A Make sure that the machine is in facsimile mode and the standby display
is shown.
If the standby display is not shown, press the {Facsimile} key.
B Press the {Program} key.
ALV019S
C Press [Delete].
7
D Select the program number you want to delete.
E Press [Yes].
Press [No] not to delete the program. The display returns to that of step .
D
F Press [Exit].
The standby display appears.
272
Download from Www.Somanuals.com. All Manuals Search And Download.
Programs
Using a Program
Follow these steps to recall and use a registered program:
A Make sure that the machine is in facsimile mode and the standby display
is shown.
If the standby display is not shown, press the {Facsimile} key.
B Place the original.
C Press the {Program} key.
ALV019S
D Confirm that [Recall] is selected, and press the registered program number.
7
The standby display appears.
The programmed fax number appears and the registered settings are recalled.
E Press the {Start} key.
The machine starts to scan the original.
Then, transmission starts with the recalled transmission settings.
Note
❒ Using the program causes the previous settings to be cleared.
❒ If you have no programmed destinations or scan settings as programs, se-
lect the program number, and then enter the fax number of the destination
and select the scan settings you require.
273
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Optional Equipment
This section explains the functions of options.
Expansion Memory (28MB: DIMM)
This allows you to send fax documents at high resolution (Super Fine). This also
allows you to receive fax documents at high resolution (Fine or Super Fine). If
Reference
p.278 “Maximum Values”
Handset
You can make or receive calls by installing the optional handset and dialing
manually.
Reference
p.226 “Manual Dial”
Extra G3 Interface Unit
7
This option provides one extra G3 line connection.
A maximum of two G3 interface units can be installed.
274
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications
❖ Fax Transmission and Reception
Standard
G3
Resolution
G3:
8 × 3.85/mm, 200 × 100 dpi (Standard character),
8 × 7.7/mm, 200 × 200 dpi (Detail character),
8 × 15.4/mm (Fine character: optional),
16 × 15.4/mm, 400 × 400 dpi (Super Fine character: optional)
Transmission time
G3: 3 seconds at 28,800 bps, Standard resolution
(JBIG transmission: 2 seconds)
Data compression method
Maximum original size
MH, MR, MMR, JBIG
Standard size: A3L, 11" × 17"
Custom size: 297 × 1200 mm/11" × 47"
Maximum scanning size
Print process
297 × 1200 mm/11" × 47"
Printing on standard paper using a laser
Transmission speed
G3:
33,600 / 31,200 / 28,800 / 26,400 / 24,000 / 21,600 / 19,200 /
16,800 / 14,400 / 12,000 / 9,600 / 7,200 / 4,800 / 2,400bps
(auto shift down system)
7
❖ Power Consumption
Immediate Transmission
Memory Transmission
Memory Reception
Reception
approx. 240 W
approx. 215 W
approx. 220 W
approx. 530 W
❖ IP-Fax Transmission and Reception
Network
LAN: Local Area Network
Ethernet/10base-T, 100base-TX, IEEE1394 (IPv4 over 1394),
IEEE802.11b (wireless LAN)
Scan line density
8 × 3.85 mm, 200 × 100 dpi (Standard character),
8 × 7.7 mm, 200 × 200 dpi (Detail character),
8 × 15.4 mm (Fine character: optional),
16 × 15.4 mm, 400 × 400 dpi (Super Fine character: optional)
Maximum original size
Standard size: A3L, 11" × 17"
Custom size: 297 × 1200 mm/11" × 47"
Maximum scanning size
Transmission protocol
297 mm × 1200 mm
Recommendation: T.38, TCP, UDP/IP communication, SIP
(RFC 3261 compliant), H.323 v2
275
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Compatible machines
IP-Fax compatible machines
IP-Fax transmission function
Specify an IPv4 address and send faxes to an IP-Fax compati-
ble fax through a network.
Also capable of sending faxes to a G3 fax connected to a tele-
phone line via a VoIP gateway.
IP-Fax reception function
Receive faxes sent from an IP-Fax compatible fax through a
network.
Also capable of receiving faxes from a G3 fax connected to a
telephone line via a VoIP gateway.
❖ Internet Fax Transmission and Reception
Network
LAN : Local Area Network
Ethernet/10Base-T, 100Base-TX, IEEE1394 (IPv4 over 1394),
IEEE802.11b (wireless LAN)
Transmit function
Scan line density
E-mail
(Super Fine character: optional) *1
A3 *1 , B4 JIS *1 , A4
Original size : Scanning width
Communication Protocols
•
Transmission
SMTP, TCP/IP
•
Reception
POP3, SMTP, IMAP4, TCP/IP
7
E-mail format
Single/Multi-part, MIME Conversion
Attached file forms: TIFF-F (MH, MR *1 , MMR *1 compression)
Authentication method
Internet communication
SMTP-AUTH, POP before SMTP, A-POP
Send and receive e-mail with a computer that has an e-mail
address
E-mail send functions
Automatic conversion of sent documents to e-mail format and
e-mail transmission. Memory transmission only.
E-mail receive functions
Automatic detection and printing of appended TIFF-F (MH)
files and ASCII text. Memory reception only.
*1
Full mode
276
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications Required for the Internet Fax Destination
Machines
This machine can communicate with Internet Fax machines that satisfy the fol-
lowing specification requirements.
When communicating with full mode compatible machines, you can take ad-
vantage of higher specifications for coding, original size, and resolution. For de-
tails about the specifications available in full mode, see “Internet Fax
Transmission and Reception” in “Specifications”.
Communication protocols
•
Transmission
SMTP
•
Reception
POP3, SMTP, IMAP4
E-mail format
•
•
Format
MIME, Base64
Content-Type
Image/tiff
Multipart/mixed (text/plain, Image/tiff (attached file forms))
Data format
•
•
•
•
Profile
TIFF Profile S
Coding
MH
7
Original size
A4
Resolution (dpi)
200×100/200×200, 204×98/204×196
Reference
p.275 “Specifications”
277
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Maximum Values
The following list contains the maximum value for each item.
Item
Standard
Expansion memory
(Optional)
Memory
4 MB
28 MB
400
Number of documents you can store in memory 400
for Memory Transmission
Number of pages you can store in memory (using Approx. 320
A4 Standard <ITU-T q1 Chart>)
Approx. 2,240
2000
Number of destinations you can register in the
destination list
2000
Number of groups you can register
100
100
500
500
500
Number of destinations you can register in a group 500
Number of destinations you can specify per file 500
Number of destinations you can specify for all
files (including files in memory)
500
Number of destinations you can search at a time 100
100
using [Search Dest.]
Number of recent destinations the machine can store 10
10
7
Number of digits for a destination
Number of digits for a SEP/SUB/PWD/SID Code 20
Number of digits in a PIN Code 20
128
128
20
20
Number of characters you can enter in the e-mail 128
subject line
128
Number of communication results you can check 200
on this machine
200
50
Number of communication results printed in the 50
Journal
Number of special senders you can register
30
30
70
Number of LAN-Fax Driver transmission results 70
you can check from a network computer “Smart-
DeviceMonitor for Admin”, “DeskTopBinder”,
or Web Image Monitor.
Number of documents sent from a LAN-Fax Driv- 400
er that the machine can retain as files to be sent
400
500
Number of destinations you can register into a
Keystroke Program
500
Number of Keystroke Programs you can register 100
100
20
Number of characters you can enter for a pro-
gram name
20
278
Download from Www.Somanuals.com. All Manuals Search And Download.
Maximum Values
Item
Standard
Expansion memory
(Optional)
Number of received documents you can store on 400
the machine's hard disk
400
Number of documents you can print at a time in 30
30
[Print / Delete Stored Reception File]
Number of documents you can delete at a time in 30
30
[Print / Delete Stored Reception File]
Number of stored documents you can specify at 30
30
a time in [Select Stored File]
Number of stored pages you can send in one op- 1,000
1,000
eration in [Select Stored File]
Number of stored documents you can print at a 30
30
time using [Print 1st Page]
Number of stored documents you can print at a 30
30
time using [Print File]
Number of documents you can store in the Doc- 2,000
ument Server using the facsimile function
2,000
Number of pages per document you can store in 1,000
the Document Server
1,000
Number of pages you can store in the Document Approx. 9,000
Server (in total – copy function, facsimile func-
tion, printer function, and scanner function) (Us-
ing ITU-T q4 Chart)
Approx. 9,000
7
Note
❒ The maximum number of pages that can be stored or transmitted may de-
crease depending on the contents of documents.
279
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
1st Sheet, 37
2nd Sheet, 37
2 Sided Original, 37
2 Sided Print, 9
Canceling a transmission before the
original is scanned, 114
Canceling a transmission before the
Canceling a transmission while the
Canceling a transmission while the
2 sided printing, 250
A
Acceptable original sizes, 40
Add, 20
Add Destination, 178
Adding a destination, 178
Address Book, 241, 254
Add User, 265
Adjust Sound Volume, 9
Advanced Features, 106
Adv.Features, 106
All, 199
Area, 54
Area 1, 54
Area 2, 54
Attach a Cover Sheet, 250
Auto Density, 58
Auto Detect, 52
Auto e-mail reception, 154
Automatic Redial, 20
Auto Reception, 152
Auto Reduce, 136
Checking a transmission file, 175
Checking files stored in memory, 187
Checking the result of the
Auto Run program, 242
B
Checking the result of the
Backup File TX Setting, 9
Basic Transmission, 246
BCC Transmission, 127
Before use, 240
Checking transmission using
LAN-Fax Driver, 252
Check Modes, 24
Clear Modes key, 5, 114
Box Setting, 9
Box Setting: Print List, 9
Broadcasting sequence, 20
Bypassing the SMTP server, 73
Clear/Stop key, 114, 115
Closed Network, 140
Closed Network Code, 140, 150
Combined Auto and Manual Density, 58
280
Download from Www.Somanuals.com. All Manuals Search And Download.
Communicating indicator, 115
Communication Failure Report, 195
Communication Page Count, 9
Communication Result Report, 194
Compatible machines, 277
Confidential File indicator, 209
Confidential File Report, 213
Confirming a transmission, 120
Confirming by e-mail, 193
Confirming by report, 192, 197
Confirming on display, 191, 196
Confirming the reservations for
SEP Code Reception, 112
Confirming the result of a
Confirming transmission results
by e-mail, 128, 252
Creating a cover sheet, 258
CSI→Own Fax Number, 150
Enable H.323, 9
Expansion memory, 274
External telephone, 99, 152
D
F
Delete, 208, 218, 272
Fax Destination, 87
Fax Header Print, 144
Fax via computer, 239
File List, 229
Delete File, 237
Deleting a destination from a
Simultaneous Broadcast, 176
Deleting a program, 272
Deleting a stored document, 237
Deleting fax information using a
Web browser, 263
Deleting programmed destinations, 256
Deleting received and
stored documents, 206, 208
Destination key, 76, 78
Detail, 49
Displaying a preview, 230
Document Server, 251
Functions not available by
e-mail reception, 32
Functions not available by
e-mail transmission, 31
Functions not available for
IP-Fax transmission, 28
Dual Access, 20
G
G3, 61
G3 Auto, 61
Gateway (VoIP gateway), 27
General Settings, 9
281
Download from Www.Somanuals.com. All Manuals Search And Download.
H
H.323, 27
H.323 Settings, 9
Handset, 99, 152, 274
Having incoming documents printed on
paper from the bypass tray, 171
How to Read This Manual, 4
Making settings for option configuration, 245
Managing facsimile functions using
Manual Density, 58
Manual Dial, 99
Menu Protect, 9
Mixed Original Sizes, 56
Mixing scan settings for a
I
Image Rotation, 167
Immediate Reception, 147
Immediate Transmission, 13, 21
Information Box, 214
Initial display, 6
Initial Settings, 9
Installing individual applications, 242
Internet Fax, 14
Internet Fax functions, 29
Internet Fax Settings, 9
IP-Fax functions, 25
J
JBIG reception, 162
JBIG transmission, 49
Journal, 197, 203
Journal by e-mail, 205
Just size printing, 171
Name, 85
Names, 83
Notes on using IP-Fax, 28
NOTICE, 1
K
Key Color, 8
Keystroke Programs, 268
L
Original Feed Type, 36, 37
Original size, 34, 40
Original sizes difficult to detect, 43
Original + Stored File, 226
Label Insertion, 138
LAN-Fax Cover Sheet Editor, 241, 258
LAN-Fax Driver, 239, 240
LDAP server, 84
Louder, 97
Lower, 97
282
Download from Www.Somanuals.com. All Manuals Search And Download.
Program / Change / Delete
Programming destinations in the
P
Page reduction, 169
Paper size and scanned area, 41
Paper Tray, 9
Parallel Memory Transmission, 13, 19
Parameter Setting, 9
Parameter Setting: Print List, 9
Password, 225
Password (SID), 109
Pause, 65
Personal Box, 157, 211
Photo, 47
PIN Code Transmission, 104
PIN Code TX, 104
Placing into the ADF, 34
Placing originals, 34
Preview, 230, 250
Prg. Dest., 83
Print, 185, 207
Print 1st Page, 231
Print completion beep, 163
Print Fax Header, 250
Print File, 231
Printing a file from memory, 185
Printing and saving, 254
Printing fax information using a
Web browser, 262
Printing on both sides, 165
Printing options, 163
Printing Personal Box documents, 212
Printing received and
stored documents, 206, 207
Printing the Journal, 198
Print Journal, 198
Print List, 187
Print Memory Lock, 209
Print per File No., 200
Print Personal Box File, 212
Print per User, 201
Print Reception Time, 9
Program, 268
Program as Defaults, 270
Program / Change / Delete Gateway, 9
Program / Change / Delete Scan Size, 9
Receiving documents according to
Reception File Setting, 9
Registering a priority function
Registering entered destinations to
Reg. No., 95
Report, 112, 113, 122, 158, 187, 194, 195,
203, 213, 253
283
Download from Www.Somanuals.com. All Manuals Search And Download.
Resending a file, 189
Resolution, 49
Returning the machine to the standby mode, 5
Routing received documents with
SUB Code, 157
SEP Code RX Reserve Report, 112
SEP Code RX Result Report, 113
Setting priority trays, 170
SID Code, 109
RTI→Own Name, 150
S
Saving as files, 251
Scan Settings, 9, 47
Scan Size, 51
Scan Type, 47
Search by destination name, 85
Search by e-mail address, 90
Search by fax number, 87
Search criteria, 92
Search Dest., 84
Search Destination, 9
Searching for a destination in the
Address Book, 84
Search using Advanced Search, 92
Second Name, 144
Select Dial / Push Phone, 9
Selecting a protocol, 61
Selecting destinations from
Recent Destinations, 79
Select Line, 61
Select Stored File, 226, 231, 233
Sender Name, 101
Sender settings, 101
Sending a stored file, 221
Sending at a specific time, 123
Sending at specific time, 249
Sending by Internet Fax, 70
Sending by IP-Fax, 67
Sending multiple originals using the
exposure glass, 18, 23
Sending over a fax line, 64
Send Later, 123
Specifying a destination by
Specifying a destination using a
Specifying an alias telephone number, 69
Stop Transmission, 115, 117
Store / Delete / Print
SUB Code Transmission, 106, 141
Subject, 130
Send Settings, 9
Send & Store, 222
SEP Code, 109, 142
SEP Code Reception, 109, 142
284
Download from Www.Somanuals.com. All Manuals Search And Download.
Substitute Reception, 149
Super Fine, 49
Using the Address Book to
Using the machine's Address Book data
in the destination list of the LAN-Fax, 257
Switching between Memory and
Immediate Transmission, 13
Switching the reception mode, 153
Switch Title, 9
Symbols, 4
System Status, 267
T
Terminology, 27
Viewing fax information using a
Viewing received fax documents
Text, 47, 133
Text / Line Art, 47
Text / Photo, 47
TIFF-F format, 29
Title 1, 77
Title 2, 77
Title 3, 77
Title word key, 6
To edit machine properties
already programmed, 264
Tone, 66
Web Image Monitor, 261
Where incoming documents are
Top to Bottom, 37
Top to Top, 37
Transfer Box, 158
Transferring received documents, 158
Transmission, 15, 21
Transmission File Status, 191
Transmission modes, 13
Transmission SUB Code, 106
Transmission with Image Rotation, 44
Transmit Failed File, 189
Transmitting Journal by e-mail, 205
Tray Shift, 173
TSI→Transmitting
Subscriber Identification, 169
TSI Print (Transmitting Subscriber
Identification Print), 169
Two-Sided Printing, 165
TX File List, 187
TX Mode, 123, 125, 127, 128, 130, 133
Types of reception, 147
285
Download from Www.Somanuals.com. All Manuals Search And Download.
286
EN
USA
B786-8510A
Download from Www.Somanuals.com. All Manuals Search And Download.
USA
❖ FCC Requirements
1. This equipment complies with Part 68 of the FCC rules and requirements adopted by the ACTA.
On the cover of this equipment is a label that contains, among other information, a product iden-
tifier in the format US:AAAEQ##TXXXXX. If requested, this number must be provided to the
telephone company.
2. This equipment uses the RJ11C USOC jack.
3. A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See installation instructions for
detail.
4. The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an in-
coming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be cer-
tain of the number of devices that may be connected to a line, as determined by the total RENs,
contact the local telephone company. The REN for this product is part of the product identifier
that has the format US:AAAEQ##TXXXXX. The digits represented by ## are the REN without
a decimal point (e.g., 03 is a REN of 0.3).
5. If this equipment causes harm to the telephone network, the telephone company will notify you
in advance that temporary discontinuance of service may be required. But if advance notice is
not practical, the telephone company will notify the customer as soon as possible. Also, you will
be advised of your right to file a complaint with the FCC if you believe it is necessary.
6. The telephone company may make changes in its facilities, equipment, operations or proce-
dures that could affect the operation of the equipment. If this happens the telephone company
will provide advance notice in order for you to make necessary modifications to maintain unin-
terrupted service.
7. If trouble is experienced with this equipment, for repair or warranty information, please contact
RICOH CORP. CUSTOMER SUPPORT DEPT. at 1-800-FASTFIX. If the equipment is causing
harm to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.
8. In the event of operation problems (document jam, copy jam, communication error indication),
refer to the solving problems section in this manual.
9. Connection to party line service is subject to state tariffs. Contact the state public utility commis-
sion, public service commission or corporation commission for information.
10. If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this equipment does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your telephone company or a qualified install-
er.
❖ WHEN PROGRAMMING EMERGENCY NUMBERS AND/OR MAKING TEST CALLS TO
EMERGENCY NUMBERS:
1. Remain on the line and briefly explain to the dispatcher the reason for the call before hanging
up.
2. Perform such activities in the off-peak hours, such as early morning hours or late evenings.
CANADA
This product meets the applicable Industry Canada technical specifications.
The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be con-
nected to a telephone interface. The termination on an interface may consist of any combination of de-
vices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.
Copyright © 2006
Download from Www.Somanuals.com. All Manuals Search And Download.
EN USA B786-8510A
Download from Www.Somanuals.com. All Manuals Search And Download.
|