INSTALLATION INSTRUCTIONS
D5RH
DIGI-5 DDS Digital Distribution System
Rack Mount 4 Source, 4 Zone Hub
08905153B
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Damage Requiring Service — These appliances should be serviced by qualified service personnel when:
• A power supply connection or a plug has been damaged or
• If liquid has been spilled into the appliance or objects have fallen into the appliance or
• The appliance has been exposed to water or moisture or
• The appliance does not appear to operate normally or exhibits a marked change in performance or
• The appliance has been dropped or the enclosure damaged.
Replacement Parts — When replacement parts are required, be sure the service technician has used replacement parts
specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
Safety Check — Upon completion of any service or repairs to this audio product, ask the service technician to perform
safety checks to determine that the audio product is in proper operating condition.
Lightning Storms — Unplug this apparatus during lightning storms or when unused for long periods of time.
Attachments and Accessories — Use only attachments/accessories specified by the manufacturer.
Cart, Stand, Tripod, Bracket or Table — Use only with a cart, stand, tripod, bracket or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip over.
Disconnect Device — Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect
device shall remain operable.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by Xantech could void the user’s authority to operate the
equipment
Caring For the D5RH
Clean only with a dry soft cloth.
It is important to properly care for your D5RH Digital Audio Distribution Hub. Follow these guidelines to ensure your device
is preserved and protected.
•
•
•
Do not expose the D5RH to rain, liquids or moisture for an extended period of time.
Do not expose the D5RH to temperature extremes.
Do not place any objects on top of the D5RH to prevent chassis damage.
Operating Temperatures & Environments
Operating Temperature: 32-104°F (0-40° C)
Humidity: 0-90%
Precautions
•
•
Always exercise care when operating the D5RH Digital Audio Distribution Hub.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
•
•
In the unlikely event that smoke, abnormal noise, or strange odor is present, immediately power the D5RH off.
Please report the problem to your dealer immediately.
Never attempt to disassemble the D5RH. You will lose any product warranty on the unit.
08905153B
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Modern Convenience
The D5RH 4 Source, 4 Zone Digital Audio Distribution Hub with DIGI-5 Technology and related
products from Xantech provides the ability to listen to 4 different audio sources in up to 28 separate
zones of the home, all over CAT-5 wiring for total flexibility and convenience. No need to have
multiple audio systems in different areas, just select a source from one of Xantech’s premium in-wall
keypads, sit back and enjoy!
Crystal Clear Digital Sound
End-to-end digital architecture means that the entire signal path of the audio system remains in the
digital domain from start to finish. This means that noise, signal loss and other unwanted effects are
never present. Each keypad contains a 30 Watt digital amplifier that allows the user to play music at
loud volume when desired. This also means that music at any volume is full and rich, without
distortion and with plenty of bass!
Simple, Logical Installation
A D5RH-based system connects using CAT-5 and speaker wire, making them reliable and easy to
install. Any digital or analog audio source can be connected directly to the D5RH Digital Audio
Distribution Hub. D5KP Amplified Keypads are connected to the D5RH using CAT-5 wiring
(inexpensive and reliable), while speakers are connected to the D5KP Amplifier Keypad using
traditional speaker wire. This eliminates the need for multiple long runs of speaker wire streamlining
the wiring process and slashing wiring costs.
Entertaining Possibilities
The D5RH’s Whole House Music and Zone Grouping features make entertaining more fun than ever.
Fully customized audio options allow for control of the entire house from one location and also allow
for the creation of multiple-zone linking where groups of zones work together in party mode.
Control for Parents
The Source Lock Out feature allows you to disable specific sources in the kid’s rooms that you don’t
want them to access.
About DIGI-5 Technology
DIGI-5 is a revolutionary new technology standard that provides a complete end-to-end digital audio
solution over CAT-5 wiring. DIGI-5 is based on advanced digital distribution and amplification circuits
that allow multi-room audio systems to be installed quickly and cost effectively.
DIGI-5 is a collaboratively developed technology that is licensed by the Linear Home Technology
Group and is being initially integrated on a Linear group-wide basis, targeted to expand market and
consumer acceptance of such systems.
08905153B
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
• 4 Source, 4 Zone Capacity
• Expandable up to 28 Zones with Optional D5XH Digital Audio Distribution Expansion Hub
• End-to-End Digital Architecture for Crystal Clear Sound with No Signal Loss
• Simple CAT-5 Wiring requirements
• Innovative D5KP Amplified Keypad (not included)
• Provide Custom Control Options
• No PC Software Required For Setup – Simply plug in the D5KP and go
• Optional D5MR – Mini Remote and D5LR – Advance Learning Remote for added control
features and remote operation
• Whole House Music – Turns On All Zones to Same Source
• Zone Functions – Do Not Disturb, Source Lock Out, Tone Control,
• Balance, Loudness, Dynamic Range Compression (DRC)
• Local (In-Room) Source Connectivity with Optional D5IP Source Input Wall Plates
• Paging/DB Functionality w/ Optional Communications Controller
• Compact Single Rack Space Design
• Rack Mountable – Optional Rack Ear Kit Available (RM1UKIT)
D5RH Accessories
• D5XH 6 Zone Expansion Router
• D5KP Amplified Keypad
• D5IP Source Input Wall Plate
• D5MR Slim-line Mini Remote
• D5LR Advance Learning Remote Control
• RM1UKIT 1U Rack Ear Kit
• Xantech Speakers
08905153B
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Defining Terms
Zone
A Zone is defined as an area of the house that has separate source selection capabilities from all
other areas of the house. Typically, a zone is comprised of a single room, but it is possible for a zone
to spread across multiple rooms (kitchen/dining room, master bedroom/master bath) or for multiple
zones to be contained in one room (game room/bar area or multiple zones in the yard).
Source
A Source is any audio (or audio/video) device that is connected to the SOURCE INPUTS of the
D5RH. Any Source can be heard in any zone in the system.
Local Source
A Local Source is an audio (or audio/video) device that is connected to a D5IP Source Input Wall
Plate. Local Sources are able to be heard only in the zone in which they are installed and may not be
heard in other zones of the system.
Front Panel
The front panel of the D5RH is populated simply by a Power LED and a Power Button. Figure 1.1
and Table 1.1 provide descriptions and locations of Front Panel controls and indicators.
2
1
Figure 1.1: D5RH Front Panel
Indicator/Button Function
LED
1 Power LED
2 Power Button
Indicates Power ON/OFF Status Red
Turns System Power ON/OFF
Table 1.1: Front Panel
08905153B
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
The Rear Panel of the D5RH has connections for Power, Source Inputs, Zone Outputs, IR Outputs,
Page/Doorbell Trigger Input, Auxiliary Power, USB and Expansion capabilities as well as
Digital/Analog Source Selection, Source Input Gain and Zone Pairing DIP Switches.
1
3
1
1
3
1
8
10
13
18
16
7
2
3
2
2
4
3
2
4
5
6
9
11
12 14
15
17
Figure 1.2: D5RH Rear Panel
Connector
Function
Connect digital audio sources using Digital
Coaxial cable
Connect digital audio sources using Digital
Optical cable
Select between Digital Coaxial, Digital Optical
or RCA connection
Connect analog audio sources using RCA
cables
1
2
3
4
Digital Coaxial Audio Input
Digital Optical Audio Input
Coaxial/Optical/RCA Selection
Switch
Analog Audio Input
5
6
Expansion Port
Source Loop Outputs
Control/Status Link to D5XH Digital Audio Hub
Audio Links to D5XH
For future 2-way data sources &
communication
7
D5-NET Port
Source-specific IR ports to control audio
sources
Non-source-specific IR port
Interface with Page/Doorbell system
Adjust Input GAIN from digital sources to avoid
distortion
8
9
IR OUT Ports
ALL IR OUT Port
10 Page/Doorbell Trigger Input
Analog Source Input Gain
Switches
11
12 USB Port
For firmware updates
13 Clip Indicators
14 Zone Pairing Switches
Displays clipping from sources
Links multiple zones
Provides additional power to D5KP Amplifier
Keypads
Connect to D5KP Amplifier Keypads located in
each zone
15 Auxiliary Power Output Port
16 Zone Output Ports
Plug into 110VAC wall outlet (Export 240VAC
models also available)
RS232 Communication Port.
17 AC Power Connector
18 RS232 Port
Table 1.2: Rear Panel
08905153B
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. System Design Overview/Applications
Planning
Before installing the D5RH, it is essential to have a detailed and accurate system design. The first
step to a good design is to map the system. It is advisable to mark up a copy of the house floor plan
with speaker, keypad and equipment locations, etc. Make sure that all locations are decided upon
before pre-wiring so that all necessary wiring and installation hardware is in place.
It is essential that ALL system components are accounted for prior to the pre-wire stage. After
establishing design goals, make a detailed list of all components. Include source equipment, keypad,
expansion hubs, local source wall plates, IR emitters, etc.
Local Source
Speakers
D5KP
CAT-5
16/2 Speaker Wire
D5IP
Sources
CAT-5
D5RH
D5XH
Audio
Cables
CAT-5
4X4 DDS EXPANSION HUB
Speakers
CAT-5
D5IP
CAT-5
16/2 Speaker Wire
D5KP
Audio
Cables
Local Source
Figure 2.1: System Wiring Overview
08905153B
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Construction
In a pre-construction installation, walls and ceilings are open with no drywall installed. This is
desirable and allows the installer greater access than in retro-fit applications. Before actually running
any wire or cable, take the time to look around each room or area of the house and plan your wire
paths for maximum efficiency. Look for routes through uncluttered parts of the stud wall or ceiling that
allow you to group all low-voltage (video, speaker wires, CAT-5, telephone, etc.) wires wherever
possible. It is a good practice to label both ends of all cables and to protect wires by tying a plastic
bag over the ends.
Note: Do not run low-voltage wires closer than 12" from high-voltage wires. If necessary, cross low-
voltage wires at a 90º angle to prevent interference.
Retro-Fit Wiring/ Post Construction
Retro-fit installations are more difficult to complete than pre-construction because walls and ceilings
are intact. Typically wires must be fished into position through walls, floors and ceilings. Holes must
be cut; speakers mounted directly in the ceiling or walls with no rough-in brackets and keypads and
local source wall plates must be mounted in existing drywall.
08905153B
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Wiring
D5RH Digital Audio Distribution Hub to D5KP Amplifier Keypad
The D5RH and all associated components are wired using CAT-5 terminated to the T-568A Wiring
Standard (Figure 2.2). When pre-wiring, run lengths of CAT-5 from the pre-determined equipment
location (the “head-end”) to each Amplifier Keypad location. The CAT-5 routes all audio, power, IR
and status information needed for full system operation.
Note: For maximum performance over long runs (more than 150 ft) run an additional 16AWG 2-
conductor wire for external power.
1 2 3 4 5 6 7 8
1 2 3 4 5 6 78
Shown tab
down
Figure 2.2: T-568A Wiring Standard
Amplifier Keypad to Speakers
Run 16AWG 2-conductor stranded copper speaker wire between Amplifier Keypad locations and
speaker locations.
Local Sources to Amplifier Keypad
Local sources are only available within the area that they are installed. They will not be available to
other areas of the house as they are not distributed by the D5RH. Run lengths of CAT-5 from any
local (in-room) source to the Amplifier Keypad located in that area.
08905153B
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Applications
There are three typical system applications when installing the D5RH. These options can be
combined throughout a system depending on the design of the system:
1 Basic 4 Source, 4 Zone System
2 Basic 4 Source, 4 Zone System - Local Sources connected using D5IP Source Input Wall Plates
3 Expanded 4 Source, 8-28 Zone System - Local Sources connected using D5IP Source Input Wall
Plates
Basic 4 Zone, 4 Source System
Figure 2.3 shows a basic D5RH system with four sources and four zones. The system is comprised of
a D5RH Digital Audio Distribution Hub, D5KP Amplified Keypad and Xantech XTC Speakers. This
configuration provides audio from each source into each zone as well as control of each source from
each zone.
SPEAKERS
16/2 SPEAKER WIRES
D5KP
CAT 5
D5RH
SOURCES
Figure 2.3: Basic System – 4 Sources/4 Zones
08905153B
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic 4 Zone, 4 Source System w/ Local Sources
Local Sources Connected Using DHIP Local Source Wall Plates
Figure 2.4 shows a basic D5RH system with four sources and four zones with the addition of Local
Sources in two of the zones. Each zone can have one local source. The system is comprised of a
D5RH Digital Audio Distribution Hub, D5KP Amplified Keypad, D5IP Source Input Wall Plates and
Xantech XTC Speakers. This configuration provides audio from each source into each zone as well
as control of each source from each zone. Zones with Local Sources have access to and control of
those sources, but the Local Sources are not available to other zones within the system.
SPEAKERS
D5IP
D5IP
16/2 SPEAKER
WIRES
CAT 5
D5KP
SOURCE
SOURCE
CAT 5
D5RH
SOURCES
Figure 2.4: Basic System w/ Local Sources – 4 Sources / 4 Zones + Local Sources
08905153B
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Expanded 4 Source, 8-28 Zone System
D5XH Expansion Router
Figure 2.5 shows an expanded system with four sources and ten zones with the addition of Local
Sources in four of the zones. Each zone can have one local source. The system is comprised of a
D5RH Digital Audio Distribution Hub, D5XH Expansion Hub, D5KP Amplified Keypad, D5IP Local
Source Wall Plates and Xantech XTC Speakers. This configuration provides audio from each source
into each zone as well as control of each source from each zone. Zones with Local Sources have
access to and control of those sources, but the Local Sources are not available to other zones within
the system. This system can be expanded up to 28 zones using additional D5XHs.
D5RH
D5XH
4X4 DDS EXPANSION HUB
Figure 2.5: Expanded System – 4 Sources / 10 Zones + Local Sources
08905153B
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Connections
The D5RH is part of an integrated system that requires the use of other components. Depending on
the system design, these components may include:
• D5KP Amplified Keypad - at least one per zone required
• D5IP Source Input Wall Plates - one per zone where a Local Source is desired
• D5XH Expansion Hub - for systems containing from 5 to 28 zones (each D5XH add up to six
zones)
• Xantech Outdoor, Ceiling and In-Wall Speakers
• Xantech IR Emitters and accessories
This section describes the connectivity between these various components and the source audio
components that comprise the system. Each D5RH system is unique and not all connections will be
made in every installation.
Important Safety Note: Make sure that the D5RH is powered OFF before making any connections.
Source Audio Inputs
The D5RH supports a total of four System Sources which are available to each of four zones and can
be sent to up to a total of twenty-eight zones using D5XH Expansion Hubs. There are two types of
Source Inputs. Source 1 and 2 both have Digital Coaxial and Digital Optical connections.
Source 3 and 4 both have three types of connectors: Analog (RCA), Digital Coaxial, and Digital
Optical. For each audio source that is connected, use only one of these connection options.
Analog
Use stereo RCA-type audio patch cables to connect an audio source to the D5RH’s Source
Input 3 or 4 as shown in Figure 3.1. Use this method for sources that do not have Digital Audio
Outputs. NOTE: Make sure to put the COAX/OPT/RCA switch in the RCA (down) position.
Audio Source
Analog Output
Stereo
RCA Patch
Cables
L
R
Figure 3.1: Source Input - Analog
08905153B
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Coaxial (DIG COAX)
Use a Digital Coaxial cable to connect an audio source with a Digital Coaxial output to the
D5RH’s Source Input as shown in Figure 3.2. NOTE: Make sure to put the COAX/OPT switch in
the COAX (up) position. Digital Connections provide the best audio quality and should be used if
available. If both a Digital Coaxial connection and a Digital Optical connection are present on the
audio source, use only one. DO NOT connect both Coaxial and Optical outputs to the D5RH.
D5RH
Digital
Coax
Cable
Digital Source
Digital Output
SPDIF
Figure 3.2: Source Input – Digital Coaxial
Digital Optical (OPTICAL)
Use a Digital Optical (TOSLINK) cable to connect an audio source with a Digital Optical output to the
D5RH’s Source Input as shown in Figure 3.3. NOTE: Make sure to put the COAX/OPT switch in
the OPT (down) position. Digital Connections provide the best audio quality and should be used if
available. If both a Digital Coaxial connection and a Digital Optical connection are present on the
audio source, use only one. DO NOT connect both coaxial and optical outputs to the D5RH.
D5RH
Digital
Optical
Cable
Audio Source
Digital Optical
Output
DIGITAL
OPTICAL
Figure 3.3: Source Input – Digital Optical
NOTE: Multi-channel digital audio formats (5.1, 7.1 etc.) are not supported by the D5IP and D5RH. However, many audio/video sources allow you to
change the digital output to PCM Stereo. In most cases this will allow multi-channel audio sources to output a “summed” stereo signal through the digital
output. Consult the audio/video source manual for details.
NOTE: Some audio sources which utilize a digital output require that you enable the digital output before it will function. If there is no audio present,
check the setup menu of the audio source to confirm that the digital output is enabled.
08905153B
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Source Loop Outputs (SOURCE LOOP OUT)
The Source Loop Outputs are used only when adding D5XH Expansion Hubs to the D5RH in order to
create more than four zones. These connectors carry Audio, Status and IR information between the
units and allow seamless functionality in all areas of the home with no complicated cross-wiring,
splicing or specialized adapters needed. When adding a D5XH Router, simply connect CAT-5 Patch
Cables from the ‘SOURCE LOOP OUT’ of the D5RH to the ‘SOURCE LOOP IN’ of the D5XH as
shown in Figure 3.4. Complete connections for expanded systems are described in the section
entitled Multi-Chassis Connections.
D5RH
Cat-5 Ethernet
Patch Cables
D5XH
Figure 3.4: Source Loop Outputs
08905153B
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
D5-NET
This connector is reserved for future implementation of two-way data sources and communication.
EXPANSION OUT
Connect the CAT-5 Patch Cable from the D5RH ‘EXPANSION OUT’ port to the D5XH ‘EXPANSION
IN’ port as shown. Complete connections for expanded systems are described in the section entitled
Multi-Chassis Connections.
D5RH
D5XH
Cat-5
Ethernet
Patch Cable
Figure 3.5: Expansion Outputs
08905153B
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
IR OUT/ALL IR OUT
Xantech D5KP Amplified Keypad feature a built-in IR Receiver that is used to control the sources
connected to the D5RH using hand-held remotes. The four IR ports labeled 1-4 are Source-Specific.
When a particular source is selected in a zone, the corresponding IR port is active and only the
selected source receives IR. This allows for same-branded or identical source components to be
controlled discreetly from one location without conflict. The ALL IR PORT is constantly active and
passes IR information regardless of the source selected. This is useful for sources that may need
control no matter which source is active, such as an A/V Receiver, or for applications utilizing an
expanded IR network including IR Distribution devices such as Xantech’s 791-44 Amplified IR
Connection Block.
To make IR connections, simply plug a standard 3.5mm IR emitter such as Xantech’s 283D IR
Emitter into the desired port. If the source that is to be connected has an IR Input port, a 3.5mm
(“mini-to-mini”) interconnect cable can be used instead. See Figure 3.6 for details.
Satellite 1
DVD
1
3
2
ALL IR OUT
IR OUT
Satellite 1
A/V Receiver
CD
Figure 3.6: IR Outputs
08905153B
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
ZONE OUT
The ‘ZONE OUT’ RJ-45 connector’s interface with D5KP Amplified Keypad through CAT-5 cables
wired to the T-568A Standard. These connectors carry IR information from the keypad as well as
audio information to the D5KP Amplifier Keypad. Status information is also carried between the D5RH
chassis and the Amplifier Keypads. While a great deal of information is handled by the ‘ZONE OUT’
connections, the connections are straightforward. Simply connect CAT-5 cables terminated to the T-
568A configuration (Figure 2.2) from each Amplifier Keypad to the corresponding ‘ZONE OUT’
connector on the D5RH hub as shown in Figure 3.7.
Note: For wire runs up to 150', the CAT-5 connections are all that is necessary. For wire runs over 150', use the AUX
POWER OUT connectors as described in the section entitled Auxiliary Power Connector (AUX POWER OUT).
D5KP Rear
D5KP Rear
D5RH
Cat-5
Cat-5
-
L+
R+
R-
+
-
L-
L+
R+
+
L-
R-
SPEAKERS
PWR IN
SPEAKERS
PWR IN
Cat-5
Cat-5
-
-
L+
R+
+
L-
R-
L+
R+
L-
+
R-
SPEAKERS
PWR IN
SPEAKERS
PWR IN
D5KP Rear
D5KP Rear
Figure 3.7: ZONE OUT Connections
08905153B
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
D5KP Speaker Connections
The D5RH routes digital audio to connected D5KP Amplifier Keypad where the audio is then
amplified and sent to in-room speakers.
WARNING!: The D5KP’s amplifier is capable of powering a single pair of 8-6 Ohm speakers.
DO NOT connect speakers with a rating of less than 6 Ohms! DO NOT connect more than one speaker to either speaker
connector of the D5KP. In doing this, damage to the D5KP may occur and will void the products warranty.
To connect speakers to D5KP Amplifier Keypad:
1 Ensure that system power is OFF!
2 Remove the SPEAKER CONNECTOR from the D5KP Amplifier Keypad
3 Strip speaker wire back 1/4"
4 Loosen speaker terminal screws on the speaker connectors
5 Insert speaker wires into terminals making sure to maintain +/- polarity
6 Tighten screws on speaker terminals
7 Re-connect the terminal strip to the SPEAKER CONNECTOR on the D5KP Amplifier Keypad
8 Connect speaker wires to the room speakers maintaining correct polarity
Figure 3.8: Speaker Connections
08905153B
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Auxiliary Power Connector (AUX POWER OUT)
For wire runs over 150’, it is recommended to run an additional 16 AWG/2-conductor wire from the
head-end location to the Amplified Keypad locations. This will allow the AUX POWER OUT terminals
to supply additional power to the Amplifier Keypads to compensate for the additional distance. For
wire runs over 300’, 16 AWG/2-conductor wire is required to operate the keypad. The maximum wire
run using CAT-5 and 16 AWG/2-conductor is 600’. Make all connections between the D5RH and the
D5KP Amplifier Keypad as previously described, then make the aux power connections described
below.
To make connections:
1 Ensure that system power is OFF!
2 Strip the ends of the 16 AWG wire 1/4" on both ends of the wire run.
3 Remove the terminal strip from the AUX POWER OUT connector on the D5RH.
4 Loosen the screws for the appropriate zone’s terminal pairs on the terminal strip.
5 Insert the wires into the terminal strip, paying close attention to polarity (+/-).
6 Tighten the screws on the terminal strip.
7 Remove the terminal strip from the PWR IN connector of the D5KP.
8 Loosen the screws on the D5KP’s PWR IN terminal.
9 Insert the wires into the terminal, paying close attention to polarity (+/-).
10 Tighten the screws on the D5KP’s PWR IN terminal.
11 Connect the terminal strip back onto the AUX POWER OUT connector on the D5RH.
Figure 3.9: AUX POWER OUT Connections
08905153B
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
USB Port (USB IN)
The USB IN port is designed to allow upgrades to the D5RH’s firmware.
AC Power Connector
Connect the supplied cord from the AC Power Connector into a properly grounded electrical outlet.
RS232 Port
Connect RS232 port to an external controller.
System Expansion
The D5RH is capable of supporting up to four sources to up to four zones. The system may be
expanded in two ways:
• Local Sources
• Adding Zones
Local Sources
Each zone of a D5RH-based system can have its own “Local” source connected directly to the zone’s
D5KP Amplified Keypad using a D5IP Source Input Wall Plate. A source connected to a D5KP is
accessible from the zone in which it is connected. It is NOT AVAILABLE to the other zones of the
system. Both audio and IR control capabilities are available to Local Sources through the D5KP. A
zone may have a maximum of one Local Source.
08905153B
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
D5IP Source Input Wall Plate
A D5IP Source Input Wall Plate is required to add a Local Source to a zone. The wall plate has audio
and IR connections similar to the SOURCE INPUT of the D5RH. A run of CAT-5 terminated to T-
568A standard (see Figure 2.2) is required between the D5KP Amplified Keypad and the location
designated for the D5IP. Connections between a source component and the D5IP are detailed in
Figure 3.10 to Figure 3.12, while connections between the D5IP and the D5KP Amplified Keypad are
detailed in Figure 3.15. NOTE: Set RCA/OPT/COAX switch to RCA (up) position.
08905153B
- 23 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3.10 to Figure 3.12: Local Source to D5IP Connections
NOTE: Multi-channel digital audio formats (5.1, 7.1 etc.) are not supported by the D5IP and D5RH. However, many
audio/video sources allow you to change the digital output to PCM Stereo. In most cases this will allow multi-channel
audio sources to output a “summed” stereo signal through the digital output. Consult the audio/video source manual for
details.
NOTE: Some audio sources which utilize a digital output require that you enable the digital output before it will function. If
there is no audio present, check the setup menu of the audio source to confirm that the digital output is enabled.
D5IP
D5KP Rear
Side View
Cat-5
-
L+
R+
+
L-
R-
SPEAKERS
PWR IN
Figure 3.13: D5IP to D5KP Connections
08905153B
- 24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
IR OUT
Connect a standard IR Emitter (283D emitter, for example) from the IR OUT port on the front of the
D5IP to the IR receiver on the front of the audio source (see Figure 3.14). For sources that have an
IR Input port on the back of the unit, use a 3.5mm to 3.5mm mono interconnect cable instead (see
Figure 3.14).
Figure 3.14: IR Out to Source Connections
08905153B
- 25 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding Zones – D5XH Digital Audio Distribution Hub
A basic D5RH system can contain a maximum of four sources and four zones. By adding D5XH
Digital Audio Distribution Expansion Hub, the system can contain a maximum of twenty-eight zones.
Each D5XH expands the system by up to six zones, while still maintaining a four source maximum
limit. This section details the connections required for adding D5XH Digital Audio Distribution
Expansion Hub to a D5RH. For detailed specifications, settings, etc., please consult the D5XH
Installation Manual.
# of Chassis
Max # of Zones
(1) D5RH
4
(1) D5RH, (1) D5XH
(1) D5RH, (2) D5XH
(1) D5RH, (3) D5XH
(1) D5RH, (4) D5XH
10
16
22
28
Zone X 4
Local Source
1 Per Zone
Sources X 4
Audio
Calbes
Cat 5
Zone X 6
Local Source
1 Per Zone
Cat 5
IR Emitters
Audio
Calbes
Cat 5
Zone X 6
Zone X 6
Zone X 6
D5RH
D5XH
Local Source
1 Per Zone
Cat 5
Cat 5
Cat 5
Cat 5
Local Source
1 Per Zone
Cat 5
D5XH
D5XH
D5XH
Cat 5
Cat 5
Cat 5
Local Source
1 Per Zone
Cat 5
Cat 5
Cat 5
08905153B
- 26 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections between a D5RH chassis and D5XH Digital Audio Distribution Hub involve CAT-5 patch
cables routed between the units. All cables are included with the D5XH. Connections are required for:
• EXPANSION OUT/EXPANSION IN
• SOURCE LOOP OUT/SOURCE LOOP IN
EXPANSION OUT/EXPANSION IN
Simply connect a CAT-5 patch cable from the D5RH’s EXPANSION OUT port to the first D5XH’s
EXPANSION IN port. For multiple D5XH units, connect a CAT-5 patch cable from the first D5XH’s
EXPANSION OUT port to the next D5XH’s EXPANSION IN port, and so on. See Figure 3.15 for
details.
SOURCE LOOP OUT/SOURCE LOOP IN
Connect a CAT-5 patch cable from each SOURCE LOOP OUT of the D5RH to each corresponding
SOURCE LOOP IN on the first D5XH. For multiple D5XH units, connect a CAT-5 patch cable from
each SOURCE LOOP OUT of the first D5XH to each corresponding SOURCE LOOP IN on the next
D5XH and so on. See Figure 3.15 for details.
D5RH
Cat-5
D5XH
Cat-5
D5XH
To Additional D5XH Chassis
Figure 3.15: System Expansion Connections
08905153B
- 27 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Settings & Operation
DIP Switch Settings
There are two groups of DIP switches on the rear panel of the D5RH that must be set prior to
operation:
• SOURCE INPUT GAIN
• KEYPAD PAIRING
ANALOG SOURCE INPUT GAIN
Analog Audio SOURCE 3 and 4 have a corresponding DIP switch to adjust the input level relative to
the other sources. Once all connections are made, the Analog Audio Source should be adjusted for
clipping (distortion) before the installation is completed.
To adjust ANALOG SOURCE INPUT GAIN DIP switches:
1 Ensure that the Analog Audio Source is connected properly to SOURCE 3 or 4.
2 Power up each source and turn on an audible signal (Press PLAY, tune to a station, etc.).
3 Select the Source (3 or 4) from the zone’s D5KP Amplifier Keypad.
4 Adjust the zone’s volume to a normal, comfortable listening level.
5 Select SOURCE 1 and then SOURCE 2 and compare the levels to SOURCE 3 and/or SOURCE
4.
6 If the analog source(s) are playing at a softer volume than the other sources, position the DIP
switch for that source to the BOOST (UP) position.
7 Observe the CLIP LED on the front of the D5RH. If it lights up constantly or consistently, the
source’s output level is too high and needs to be adjusted. In this case, position the appropriate
DIP switch to the DEFAULT (DOWN) position.
8 Repeat this process for the other analog source.
ZONE PAIRING
The ZONE PAIRING DIP switches allow each of the zones to be paired or grouped with any other
zone. Any zone that is in the UP position will be paired with any other zone that is also placed in the
UP position. This feature is useful to create large “party” zones where combined areas of the house
share audio and system control.
08905153B
- 28 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Troubleshooting
Table 5-1 provides troubleshooting information for the D5RH Digital Audio Distribution Hub.
Audio
Symptom
Possible Cause
Solution
No audio present in a specific
zone
1. Source not playing
Press Play, turn ON, etc.
2. Zone not ON
3. Zone volume turned all the
way down
Press “Power” on the D5KP
Increase volume
4. Speakers in room miswired or a. Test known good speaker at
defective, or D5KP miswired
D5KP speaker connector
b. Verify connections
No audio from specific source
Digital audio output not enabled Check setup menu and confirm
digital audio output is enabled
Multi-channel digital audio
formats (5.1, 7.1 etc.) are not
supported by the D5IP, D5RH,
etc.
Change digital Output to PCM
Stereo
Incorrect audio format selection. Check RCA/OPT/COAX
selection switch for proper
selection.
No audio present in any zone
1. See above
Perform steps above
2. Digital source is outputting
Select PCM Stereo output on
multi-channel audio format (5.1, source component. Consult
7.1, etc.) source’s manual for details.
3. Digital output not enabled on Enable digital output through
source
source’s menu. Set to PCM
stereo. Consult source’s manual
for details.
Hum or buzz through system
speakers
1. Ground loop
Ensure proper grounding using
a three prong grounded AC
outlet.
2. Receiver/Amplifier level too
high
Reduce level
Poor Audio quality
1. Clipping or distortion
2. Speaker out of phase
Adjust GAIN settings
Carefully check polarity of each
speaker
3. Incorrect assignment of
left/right source RCA cables or
speaker cables
Isolate to source or room and
correct
08905153B
- 29 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Specifications
Power Input
120 VAC / 3 Amps (Export 240VAC
models also available)
Sampling Frequency
Digital Audio Resolution
Signal to Noise Ratio
Input GAIN Switches
(Input Sensitivity)
48kHz
24 Bit
94dB
DIP Switch 3 & 4 UP
DIP Switch 3 & 4 DOWN
Frequency Response
1.35Vrms / 4.8dBu
2V rms / 8.2dBu
20Hz-20kHz +/- 0.1dB
Dimensions
H x W x D (w/ feet)
2 3/8" x 17" x 14 1/8"
(8.6cm x 43.2cm x 35.9cm)
H x W x D (w/o feet)
Weight
1 3/4" x 17" x 14 1/8"
(4.4cm x 43.2cm x 35.9cm)
19lbs (8.6kg) Unit Weight
21lbs (9.5kg) Shipping Weight
08905153B
- 30 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Xantech Limited Warranty
(Effective for products sold after July 1, 2006)
Xantech Corporation (“Xantech”) warrants to the holder of a valid proof of purchase as the first end-user purchaser
(“You”), its products to be free from defects in materials and workmanship for the periods specified below from the date of
purchase. This limited warranty extends only to You for product purchased and used in the United States of America. For
product purchased outside of the United States of America, You must contact the Xantech authorized distributor in your
region for warranty services. Product is not intended for end user installation. If within the applicable warranty period
above You discover such item was not as warranted above and You promptly notify Xantech in writing, Xantech shall
repair or replace the items at its option. Xantech may elect which remedy or combination of remedies to provide in its sole
discretion. Xantech may use functionally equivalent reconditioned/refurbished/pre-owned or new products or parts under
this limited warranty. This warranty shall not apply (a) to product which shall have been installed by other than an
authorized Xantech installer, (b) to installed product which is not installed to Xantech’s specifications, (c) to product which
shall have been repaired or altered by others than Xantech, (d) to charges for installation or set up or adjustment of
customer controls, (e) to product that has suffered normal cosmetic deterioration (f) to product which shall have been
subjected to negligence, misuse, abuse, accident, or damage by circumstances beyond Xantech’s control, including, but
not limited to, lightning, flood, electrical surge, tornado, earthquake, or any other catastrophic events beyond Xantech’s
control, or (g) to product which shall have been subjected to improper operation, connected equipment failure or
malfunction, inadequate packing or shipping damage, maintenance or storage, or to other than normal use of service. The
foregoing warranties do not cover reimbursement for labor, transportation, shipping, removal, installation, or other
expenses which may be incurred in connection with repair or replacement. All claims for product shipping damage must
be processes within 3 days of receipt by You.
A Xantech Return Authorization (RA) must be obtained from Xantech by You, your installer or your distributor for Product
covered under this warranty. Covered product must be sent to Xantech together with proof of purchase, RA number,
prepaid and insured to Xantech. Freight collect shipments will be refused. Risk of loss or damage in transit is borne by the
sender. Xantech's warranty does not cover Products which have been received improperly packaged, altered, or
physically damaged. Products will be inspected upon receipt.
Except as may be expressly provided and authorized in writing by Xantech, Xantech shall not be subject to any other
obligations or liabilities whatsoever with respect to equipment manufactured or sold by Xantech or services rendered by
Xantech.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
ATTENTION: TO OUR VALUED CONSUMERS
To insure that consumers obtain quality pre-sale and after-sale support and service, Xantech products are sold
exclusively through authorized dealers and authorized distributors. The warranties on Xantech products are NOT VALID if
the products have been purchased from an unauthorized dealer or distributor. In order to determine if your Xantech re-
seller is authorized, please call Xantech (800) 843 - 5465.
XANTECH PRODUCT
WARRANTY DURATION
(go to Xantech.com/warranty for model numbers)
IR Receivers and IR Emitters
Remote Control Switchers
Modules and Connecting Blocks
Accessories
Limited Lifetime
Limited Lifetime
Limited Lifetime
Limited Lifetime
Limited Lifetime
5 year Limited
2 year Limited
2 year Limited
2 year Limited
1 year Limited
1 year Limited
1 year Limited
Speakers
Volume Controls and Speaker Selectors
DIGI-5, MRC, BX, ZPR and Commercial Products
Amplifiers
Control Interfaces
Hand Held Remote Controls
SPLCD Product
Source Components, XIS100
08905153B
- 31 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Xantech Corporation
13100 Telfair Ave. 2F, Sylmar CA 91342 | Xantech.com
Installation Instructions, D5RH © 2008 Xantech Corporation
Document # 08905153B
This document is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Xantech
Corporation. Xantech Corporation shall not be liable for operational, technical, or editorial errors/omissions made in this document.
08905153B
- 32 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|