Woodstock Lathe SB1039F User Manual

MODEL SB1039F  
14" X 40" LATHE 220V w/DRO  
Manual Insert  
PHONE: (360) 734-1540 www.southbendlathe.com  
The Model SB1039F Lathe is the same machine as the Model SB1039 except for the following:  
Added a 2-Axis Fagor Digital Readout (DRO).  
Except for the differences noted in this insert, all other content in the Model SB1039 Owner’s Manual  
applies to this machine. Before operating your new lathe, you MUST read and understand this insert,  
the entire Model SB1039 Owner’s Manual, and the Fagor DRO Owner’s Manual to reduce the risk of  
injury when using this machine. Keep this insert for later reference.  
If you have any further questions about this manual insert or the differences between the Model  
SB1039F and the Model SB1039, contact our Technical Support at (360) 734-1639 or email  
New & Changed Parts  
1601  
O
R
1518-1  
1518  
0V w/D  
MFG Date  
THE 22  
A
MODEL SB1039F  
LE USING THIS  
!
o.  
G
Y
WHI  
N
I
Serial  
N
NJUR  
N
R
A
W
er source.  
.
w
14"  
x
4" 16  
v
S
!
PEED  
L
ting  
ng hair and  
lo  
ent  
OUS PERSONAL  
I
e
e
star  
.
s
or  
cohol.  
.
y; secur  
ting  
welr  
drugs or al  
ye protection.  
or je  
e
or adjustme star  
,
or  
ef  
ed  
es  
v
glo  
uck and has  
skin.  
,
ntenance,  
O
REDUCE THE RISK OF SERI  
ng  
T
the.  
CHINE:  
a
act with  
MA ead and understand manual bef  
vice, mai  
the machine is connected to  
R
e
a
grounded po  
1.  
2.  
3.  
4.  
5.  
ely held in the ch  
.
e
ser  
ly adjusted/setinugp tbhe  
oid cont  
l
Always wear appro  
es  
or ed or under the influence of  
v
.
ning  
Make sur  
e
star  
or  
ly and av  
and secur  
T
wear loose clothi  
te when tir  
eep all guards in place.  
n
motion.  
ar  
ted.  
ou  
K
wer bef  
y
l
e
tur  
DO NO  
a
gular  
tion bef  
proper  
e
er chuck.  
e
,
A
roll up long slee  
0V  
22  
s
4.3  
T
oper  
to the machine.  
,
1
Disconnecettphoe machine is prnotp  
h
P
terial  
suppor  
kpiectetewndhleedn.it is  
or  
y
y
ng:  
7"  
6.  
7.  
8.  
9.  
y
i
i
kpiece  
or  
i
Hz ti  
.1  
DO NO  
a
R
,
60  
:
5/2.5H  
Make sure  
w
ent  
r
6"  
.6  
8
e
prooprerthe ma  
r
vised access  
:
14  
ance through full rota  
Change cutting fluid  
r
te  
f
Motor  
Cu  
a
e:  
e
the chuck ke  
the running una  
he chuck or  
kpieces ar  
e
ad  
3-P  
Make sur  
w
e
hr Bed  
e
clear  
"
ll-Lo  
Fu  
10.  
unsuper  
94  
"
saf  
.
er leav  
or  
the la  
t
v
e
long  
:
20  
Ne  
Ne  
Ne  
ce Between Centers: 40"  
er touch  
Swing Over Cross Slid  
v
v
11.  
12.  
13.  
14.  
15.  
16.  
en to hav  
e
w
er leav  
Gap": 6.46  
Distan er Gap  
ck  
el:  
7
4
"
Swing Ov  
Swing Ov  
w
childr  
av  
r
Make sur  
el:  
1-5  
le Nose to  
Camlo  
av  
r
T
T
Always use the proper speed  
Do not allo  
r
ind  
Sp  
d
ss Slide  
un  
7"  
#3  
Cro  
le: MT#5  
e: 1.5  
se: Dind k: MT  
le No  
r
Compo  
tions  
a
ind  
le Bo  
Sp  
fic  
Speci  
Sp  
Sp  
ailstoc  
ind  
T
.
s
Bend  
0
lb th  
aper Inside  
an  
T
42  
aper Insideto  
2
Sou  
T
W
ght:  
ei  
aiw  
Made in  
T
1518-3  
1618  
1518-2  
REF  
1518  
PART #  
PSB1039F1518  
DESCRIPTION  
DRO ASSEMBLY FAGOR 2-AXIS  
REF  
PART #  
DESCRIPTION  
1518-3 PSB1039F1518-3 DRO Y-AXIS SCALE FAGOR MKT-22  
1518-1 PSB1014F2318-1 DRO DISPLAY FAGOR 20-iT  
1518-2 PSB1037F2318-2 DRO X-AXIS SCALE FAGOR MKT-102  
1601  
1618  
PSB1039F1601  
PSB1039F1618  
MACHINE ID LABEL  
MODEL NUMBER LABEL  
Copyright © June, 2011 by South Bend Lathe Co.  
WARNING: No portion of this manual may be reproduced without written approval.  
#BL14239 Printed in USA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mfg. Since 4/11  
Model SB1039F  
M A N U A L I N S E R T  
Main Specifications  
Operation Info  
Swing Over Bed.................................................................................................................................. 14.17 in.  
Distance Between Centers...................................................................................................................... 40 in.  
Swing Over Cross Slide........................................................................................................................ 8.66 in.  
Swing Over Saddle............................................................................................................................. 13.75 in.  
Swing Over Gap.................................................................................................................................. 20.94 in.  
Maximum Tool Bit Size........................................................................................................................ 0.75 in.  
Compound Travel...................................................................................................................................... 4 in.  
Carriage Travel..................................................................................................................................... 36.5 in.  
Cross Slide Travel...................................................................................................................................... 7 in.  
Headstock Info  
Spindle Bore.......................................................................................................................................... 1.57 in.  
Spindle Taper.......................................................................................................................................... MT#5  
Number of Spindle Speeds............................................................................................................................ 16  
Spindle Speeds......................................................................................................................... 50 – 2570 RPM  
Spindle Type.............................................................................................................................. D1-5 Camlock  
Spindle Bearings............................................................................................................. NTN Tapered Roller  
Spindle Length.................................................................................................................................... 20.87 in.  
Spindle Length with 3-Jaw Chuck.................................................................................................... 28.74 in.  
Spindle Length with 4-Jaw Chuck.................................................................................................... 30.71 in.  
Tailstock Info  
Tailstock Quill Travel............................................................................................................................. 4.5 in.  
Tailstock Taper........................................................................................................................................ MT#3  
Tailstock Barrel Diameter.................................................................................................................. 1.968 in.  
Threading Info  
Number of Longitudinal Feeds..................................................................................................................... 17  
Range of Longitudinal Feeds................................................................................................ 0.002 – 0.067 in.  
Number of Cross Feeds................................................................................................................................. 17  
Range of Cross Feeds............................................................................................................. 0.001 – 0.034 in.  
Number of Inch Threads............................................................................................................................... 45  
Range of Inch Threads..................................................................................................................... 2 – 72 TPI  
Number of Metric Threads........................................................................................................................... 39  
Range of Metric Threads.............................................................................................................. 0.2 – 14 mm  
Number of Modular Pitches.......................................................................................................................... 18  
Range of Modular Pitches............................................................................................................ 0.3 – 3.5 MP  
Number of Diametral Pitches....................................................................................................................... 21  
Range of Diametral Pitches.............................................................................................................. 8 – 44 DP  
Dimensions  
Bed Width.................................................................................................................................................. 9 in.  
Leadscrew Diameter............................................................................................................................ 1-1/8 in.  
Leadscrew TPI................................................................................................................................................. 4  
Leadscrew Length.................................................................................................................................... 59 in.  
Steady Rest Capacity............................................................................................................. 5/16 – 4-5/16 in.  
Follow Rest Capacity.................................................................................................................. 5/8 – 3-1/8 in.  
Faceplate Size.......................................................................................................................................... 12 in.  
Feed Rod Diameter................................................................................................................................. 3/4 in.  
Floor to Center Height...................................................................................................................... 42-5/8 in.  
Height With Leveling Jacks.............................................................................................................. 54-3/8 in.  
-3-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model SB1039F  
Mfg. Since 4/11  
M A N U A L I N S E R T  
Construction  
Base.................................................................................................................................................... Cast Iron  
Headstock.......................................................................................................................................... Cast Iron  
Headstock Gears.......................................................................................................... Flame Hardened Steel  
Bed.............................................................................................. Induction Hardened and Ground Cast Iron  
Stand.................................................................................................................................................. Cast Iron  
Paint................................................................................................................................................... Urethane  
Other  
Country Of Origin .............................................................. Taiwan (Some Components Made in USA and Japan)  
Warranty ......................................................................................................................................................... 1 Year  
Serial Number Location ................................................................................. ID Label on Rear Side of Left Stand  
Assembly Time ...................................................................................................................... Approximately 1 Hour  
Sound Rating .................................................................................................................................................... 76 dB  
Features  
Allen Bradley Electrical Components  
Fagor DRO  
Meehanite Casting, Signature South Bend Three V-Way Bed  
Safety Chuck Guard with Micro-Switch Shut-Off  
Halogen Work Light (24V/70W)  
4-Way Tool Post  
Complete Coolant System  
Micrometer Carriage Stop  
Threading Dial Indicator  
NTN Japanese Spindle Bearing  
Full Length Splash Guard  
Front Removable Sliding Chip Tray  
Headstock Gears Run in an Oil Bath  
Completely Enclosed Universal Gearbox for Cutting Inch, Metric, Modular and Diametral Pitches  
Jog Button and Emergency Stop  
Included Accessories  
10 in. 4-Jaw Independent Chuck D1-5  
8 in. 3-Jaw Scroll Chuck (Mounted to 8 in. D1-5 Back Plate)  
12 in. Faceplate D1-5  
Follow Rest  
Steady Rest with Roller Bearing Tips  
#5 to #3 Morse Taper Spindle Sleeve  
Two Morse Taper #3 Dead Centers (1 Carbon Steel and 1 Carbide-Tipped)  
Six Leveling Pads  
Service Tools  
Tool Box  
USA Written Manual  
-4-  
Download from Www.Somanuals.com. All Manuals Search And Download.  

West Bend Popcorn Poppers L5786 User Manual
Whirlpool Refrigerator 2211602 User Manual
White Rodgers Thermostat 1F51N 619 User Manual
Windsor Vacuum Cleaner SRS12 User Manual
Wolf Oven FHBO User Manual
Woodstock Lathe W1704 User Manual
Xerox Printer Phaser 6300 6350 User Manual
Xpelair CD Player XIM100+ User Manual
Zanussi Refrigerator ZRT 155W User Manual
Zebra Technologies Printer RW 220 User Manual