SKID STEER
TILLER
TL52
TL73
TL84
Effective Serial Numbers:
TL52A 4200690202
TL73A 4300730102
TL84A 5600020102
Tested. Proven. Unbeatable.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
SERVICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
PARTS INDEX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
HYDRAULIC FITTING TORQUE CHART. . . . . . . . . . . . . . . . . . . . . . . . . . .26
QUICK COUPLER KITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .31
PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . INSIDE BACK COVER
Introduction 3
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL INFORMATION
The purpose of this manual is to assist you in operating
The illustrations and data used in this manual were cur-
rent at the time of printing but, due to possible inline
production changes, your machine may vary slightly in
detail. We reserve the right to redesign and change the
machines as may be necessary without notification.
and maintaining your tiller. Read it carefully. It furnishes
information and instructions that will help you achieve
years of dependable performance. These instructions
have been compiled from extensive field experience
and engineering data. Some information may be gen-
eral in nature due to unknown and varying operating
conditions. However, through experience and these
instructions, you should be able to develop procedures
suitable to your particular situation.
Throughout this manual, references are made to right
and left direction. These are determined by standing
behind the equipment facing the direction of forward
travel.
SPECIFICATIONS
TL52
TL73
TL84
Dual Direct
Dual Direct
Dual Direct
Motor
Char-Lynn 2000 - 18.7
3300 psi (228 bars)
0 - 6 Inches
Char-Lynn 2000 - 18.7
3300 psi (228 bars)
0 - 6 Inches
Ross ME180405 AAAB
5000 psi (245 bars)
0 - 6 Inches
Maximum Pressure
Working Depth
Working Width
Overall Width
Overall Length
Tines
52 Inches (1321 mm)
60 Inches (1524 mm)
44 Inches (1118 mm)
28
73 Inches (1854 mm)
86 Inches (2184 mm)
44 Inches (1118 mm)
36
84 Inches (2134 mm)
97 Inches (2462 mm)
44 Inches (1118 mm)
40
RPM
@12 gpm (46 lpm)
148 rpm
@15 gpm (76 lpm)
247 rpm
@20 gpm (76 lpm)
247 rpm
@15 gpm (57 lpm)
185 rpm
@25 gpm (95 lpm)
309 rpm
@25 gpm (95 lpm)
432 rpm
@18 gpm (69 lpm)
22 rpm
@32 gpm (122 lpm)
395 rpm
@32 gpm (122 lpm)
432 rpm
@40 gpm (152 lpm)
540 rpm
MAN0003 (Rev. 11/30/2006)
4 Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
ꢀ Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gan-
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be erased
by an operator’s single careless act.
grene, serious injury, or death will result. CON-
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
In addition to the design and configuration of
equipment, hazard control and accident preven-
tion are dependent upon the awareness, concern,
judgement, and proper training of personnel
involved in the operation, transport, maintenance
and storage of equipment.
ꢀ Never allow children or untrained persons to
operate equipment.
PREPARATION
It has been said “The best safety device is an
informed, careful operator.” We ask you to be that
kind of operator.
ꢀ Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
ꢀ Counterweight ballast may be required for
machine stability. Check your power unit manual or
contact your dealer.
INSTALLATION
ꢀ Hydraulics must be connected as instructed in
this manual. Do not substitute parts, modify, or
connect in any other way.
ꢀ Air in hydraulic systems can cause erratic oper-
ation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
ꢀ After connecting hoses, check that all control
lever positions function as instructed in the Opera-
tor's Manual. Do not put into service until control
lever and equipment movements are correct.
TRAINING
ꢀ After connecting hoses, check that all control
lever positions function as instructed in the Opera-
tor's Manual. Do not put into service until control
lever and equipment movements are correct.
ꢀ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
ꢀ Protective hose sleeves must cover all hydrau-
lic hoses within 20 inches of the operator and be
secured onto metal hose fittings. Replace hoses or
sleeves if damaged or if protective sleeve cannot
be properly positioned or secured.
ꢀ Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
ꢀ If you do not understand any part of this manual
and need assistance, see your dealer.
ꢀ Know your controls and how to stop engine and
attachment quickly in an emergency.
ꢀ
Operators must be instructed in and be capable
of the safe operation of the equipment, its attach-
ments, and all controls. Do not allow anyone to
operate this equipment without proper instructions.
ꢀ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
(Safety Rules continued on next page)
ꢀ Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
Alitec Tiller SR (Rev. 11/30/2006)
Safety 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
(Safety Rules continued from previous page)
ꢀ Do not operate or transport equipment while
under the influence of alcohol or drugs.
ꢀ Be sure attachment is properly secured,
adjusted, and in good operating condition. Coupler
lockpins must be fully extended and properly
engaged into attachment retaining slots.
ꢀ Operate only in daylight or good artificial light.
ꢀ Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
ꢀ Power unit must be equipped with ROPS and
seat belt/operator restraint. Keep seat belt/operator
restraint securely fastened/engaged. Falling off
power unit can result in death from being run over
or crushed. Keep ROPS systems in place at all
times.
ꢀ Always comply with all state and local lighting
and marking requirements.
ꢀ Do not allow riders. Do not lift or carry anybody
on the power unit or attachments.
ꢀ Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
ꢀ Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt/operator restraint, place transmission in park
or neutral, engage brake and ensure all other con-
trols are disengaged before starting power unit
engine.
ꢀ
Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
ꢀ Inspect and clear area of stones, branches, or
other hard objects that might be thrown, causing
injury or damage.
ꢀ Look down and to the rear and make sure area
is clear before operating in reverse.
OPERATION
ꢀ Improper operation can cause the machine to
tip or roll over and cause injury or death.
ꢀ Use extreme care when working close to fences,
ditches, other obstructions, or on hillsides.
•
Keep power unit lift arms and attachment as
low as possible.
Do not travel or turn with power unit lift arms
and attachment raised.
•
ꢀ Do not operate or transport on steep slopes.
•
•
•
•
Turn only on level ground.
ꢀ Do not stop, start, or change directions sud-
denly on slopes.
Go up and down slopes, not across them.
Keep the heavy end of the machine uphill.
Do not overload the machine.
ꢀ Use extreme care and reduce ground speed on
slopes and rough terrain.
ꢀ Never use attachment to carry loads that exceed
the rated operating capacity or other specifications
of the power unit. Check your power unit manual or
see your dealer for rated operating capacity.
Exceeding this capacity can cause machine to tip,
roll over, or present other hazards that can cause
injury or death.
ꢀ Watch for hidden hazards on the terrain during
operation.
ꢀ Stop power unit and implement immediately
upon striking an obstruction. Dismount power unit,
using proper procedure. Inspect and repair any
damage before resuming operation.
ꢀ Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
ꢀ Leak down or failure of mechanical or hydraulic
system can cause equipment to drop.
ꢀ Contact with high voltage, overhead power
lines, underground cables, gas lines, and other
hazards can cause serious injury or death from
electrocution, explosion, or fire.
ꢀ Before making any adjustments on attachment,
stop engine and engage parking brake. Never
adjust or work on attachment while the power unit
or attachment is running.
ꢀ Keep bystanders away from equipment.
ꢀ Never direct discharge toward people, animals,
(Safety Rules continued on next page)
or property.
Alitec Tiller SR (Rev. 11/30/2006)
6 Safety
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
(Safety Rules continued from previous page)
ꢀ Never perform service or maintenance with
engine running.
MAINTENANCE
ꢀ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
ꢀ Before leaving operator's seat, follow power
unit manual instructions. Lower lift arms and put
attachment on the ground. Stop engine, remove
key, engage brake, and remove seat belt/operator
restraint.
ꢀ Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.
ꢀ NEVER GO UNDERNEATH EQUIPMENT. Never
place any part of the body underneath equipment
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.
ꢀ Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
ꢀ
Make sure shields and guards are properly
installed and in good condition. Replace if damaged.
• Service work does not require going under-
neath.
• Read Operator's Manual for service instruc-
tions or have service performed by a qualified
dealer.
ꢀ Do not disconnect hydraulic lines until all sys-
tem pressure is relieved. Lower unit to ground,
stop engine, and operate all hydraulic control
levers.
ꢀ Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its compo-
nents in any way.
ꢀ Leak down or failure of mechanical or hydraulic
system can cause equipment to drop.
STORAGE
ꢀ Your dealer can supply original equipment
hydraulic accessories and repair parts. Substitute
parts may not meet original equipment specifica-
tions and may be dangerous.
ꢀ Follow manual instructions for storage.
ꢀ Keep children and bystanders away from stor-
ꢀ Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
age area.
Alitec Tiller SR (Rev. 11/30/2006)
Safety 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
1 - Serial Number Plate
2 - PN 54519
3 - PN D0200
4 - PN D0209
WARNING
FALLING OFF CAN RESULT IN BEING RUN OVER.
■ Skid steer must have ROPS and seat belt/operator restraint.
Keep seat belt/operator restraint securely fastened.
D0209
■ Never allow riders.
RAISED EQUIPMENT CAN DROP AND CRUSH.
■ Never go under raised equipment or raised skid steer lift
arms. They can drop from hydraulic or mechanical failure, or
moving control levers.
■ Service work does not require going under equipment. Read
manual instructions.
FALLING OFF OR GOING UNDER MACHINE CAN RESULT IN
SERIOUS INJURY OR DEATH.
54519-B
5 - PN 19924
WARNING
Check for leaks with cardboard; never use hand.
Before loosening fittings: lower load, release pressure, and
be sure oil is cool.
Consult physician immediately if skin penetration occurs.
19924-B
6 - PN D0404
TO AVOID SERIOUS INJURY OR DEATH:
WARNING
ꢀ Read attachment and power unit manuals before you use,
service, or repair machine. Follow all safety rules and
instructions. (Manuals can be obtained from your dealer, or
in the United States and Canada call 1-800-319-6637.)
ꢀ Use only when sitting in operator's seat with seat belt/
operator restraint fastened.
ꢀ Before leaving operator's seat, follow power unit manual
instructions, lower lift arms and attachment to ground, stop
engine, remove key, engage brake, and remove seat belt/
operator restraint.
ꢀ Never let children or untrained persons run equipment.
D0404-C
(Rev. 4/4/2008)
MAN0003 (Rev. 11/30/2006)
8 Safety
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
BE CAREFUL!
Use a clean, damp cloth to clean safety decals. Avoid spraying too close to decals when using a
pressure washer; high-pressure water can enter through very small scratches or under edges of
decals causing them to peel or come off.
Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest
Canada call 1-800-319-6637.
(Rev. 4/4/2008)
MAN0003 (Rev. 11/30/2006)
Safety 9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
___ Keep all bystanders away from equipment work-
ing area.
___ Check that all hydraulic hoses and fittings are in
good condition and not leaking before starting
power unit.
ꢀ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
___ Check that hoses are not twisted, bent sharply,
kinked, frayed or pulled tight. Replace any dam-
aged hoses immediately.
___ Make sure power unit ROPS and seat belts are in
good condition. Keep seat belt securely fastened
during operation.
ꢀ Power unit must be equipped with ROPS and
seat belt/operator restraint. Keep seat belt/operator
restraint securely fastened/engaged. Falling off
power unit can result in death from being run over
or crushed. Keep ROPS systems in place at all
times.
TILLER INSTALLATION
Read instructions in the skid steer operator’s manual
for connecting and removing attachment.
Place the couplers in the disengaged position as
shown in Figure 1. Rotate the skid steer attachment
slightly forward and fully lower the lift arms.
■
The operator is responsible for the safe opera-
tion of this equipment. Operators must be
instructed in and be capable of the safe operation
of the equipment, its attachments and all controls.
Do not allow anyone to operate this equipment
without proper instructions.
ꢀ
Skid steers must be equipped with an auxiliary
hydraulic system capable of supplying continuous
flow for hydraulic motor operation.
PRE-OPERATION CHECK LIST
Owner’s Responsibility
___ Review and follow all safety rules and decals.
See safety rules on page 5 and safety decals on
page 8.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
___ Check that all shields and guards are properly
installed and in good condition. Replace if dam-
aged.
DP1
Figure 1.
Pull forward to the attachment as shown in Figure 2.
Make sure the outside of the skid steer attach (1) is
aligned with the inside of the tiller attach (2). Continue
to pull forward until the skid steer attach makes contact
with the tiller attach. Raise the skid steer arms until the
top of the skid steer attach contacts the top latch bar
(3) on the tiller.
___ Check that equipment is properly and securely
attached to skid steer.
___ Check that all hardware and cotter pins are prop-
erly installed and secured.
___ Do not allow riders.
10 Operation
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
depth skid for the desired cutting depth. Reinstall the
two bolts and torque to 250 lbs-ft (325 N-m).
3
2
1
DP2
Figure 2.
Roll the skid steer arms back until the tiller is com-
pletely off the ground. Engage the parking break on the
skid steer. Stop engine and relieve the back pressure in
the auxiliary hydraulic system. Exit the skid steer.
1. 5.50" Cutting Depth
2. 4.25" Cutting Depth
3. 2.25" Cutting Depth
6.00" Cutting Depth if Skid is Removed
Move the coupler pins to the engaged position. Hook
up the auxiliary hydraulic hoses. Be sure they are
routed to prevent any hose interference. Check the
attach pins (4) to be sure they are fully engaged in the
attach bracket as shown in Figure 3.
Figure 4.
TILLER OPERATION
4
■
Read and understand the tiller and skid steer
operator’s manuals before operating the tiller. Fail-
ure to do so may result in death, serious personal
injury or properly damage.
The tiller is a hydraulic powered attachment intended to
cultivate soil. The tiller attachment operation is bi-direc-
tional; it will operate with tines rotating in either direc-
tion.
The TL52 has an offset mounting configuration to allow
the right tracks to be covered when the skid steer
moves in reverse for finishing the tilling operation.
DP3
The performance of the tiller can vary significantly
depending upon the way it is used. The tiller attach-
ment requires a minimum hydraulic supply. For require-
ments on each model see specifications on page 4.
Figure 3.
TILLER DEPTH ADJUSTMENT
All tiller models have four depth settings. Moving the
depth skid location allows the depth setting to be
changed. Figure 4 shows the cutting depth for the four
depth positions. When making adjustments, be sure
that both skids are set at the same position.
To change the depth skid position, lower the tiller to the
ground so the weight is supported on the tines.
Remove the two bolts from each depth skid. Adjust the
Operation 11
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING
NOTICE
■
To avoid tiller and motor damage, stop prime
After Each Use
mover hydraulic flow. Allow tiller to stop com-
pletely before changing direction of rotation.
●
●
●
Remove large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
For maximum productivity and to maintain optimal
operation, keep chassis free of residue build up and
replace worn or broken tines.
Inspect machine and replace worn or damaged
parts.
Replace any safety decals that are missing or not
readable.
Never raise the attachment more than 24" off the
ground. When loading, keep the attachment as low to
ramps and trailers as possible.
Periodically or Before Extended Storage
For finish tilling operation, the tiller may be operated in
the reverse direction with the tines rotating in a clock-
wise direction when viewed from the left side of the
machine.
●
Clean large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
●
Remove the remainder using a low-pressure water
spray.
Roll the skid steer arms fully back and lower the arms
completely. Activate auxiliary hydraulics and make sure
the tines are rotating in the desired direction. Bring skid
steer to high idle, slowly tilt the tiller forward until the
depth skids contact the ground. Move the skid steer in
the desired direction of travel.
1. Be careful when spraying near scratched or torn
safety decals or near edges of decals as water
spray can peel decal off surface.
2. Be careful when spraying near chipped or
scratched paint as water spray can lift paint.
3. If a pressure washer is used, follow the advice
TRANSPORT
of the pressure washer manufacturer.
●
●
Inspect machine and replace worn or damaged
parts.
NOTICE
■
When transporting the attachment, be sure the
tines do not contact the ground as this may cause
the drum to turn resulting in damage to the motor.
Sand down scratches and the edges of areas of
missing paint and coat with spray paint of matching
color (purchase from your dealer).
Roll the skid steer arms fully back and raise the attach-
ment 12" to 15" from the ground. Avoid excessive
ground speed and sudden maneuvers. Never raise the
attachment more than 24" off the ground. When load-
ing, keep the attachment as low to ramps and trailers
as possible.
●
Replace any safety decals that are missing or not
readable (supplied free by your dealer). See Safety
Decals section for location drawing.
STORAGE
NOTICE
■
Store the tiller inside when possible. If this is
not possible, store the tiller on a pallet. Be sure the
tiller is stored off the ground to protect the cou-
plers and hoses.
ꢀ Improper operation can cause the machine to
tip or roll over and cause injury or death.
• Keep power unit lift arms and attachment as
low as possible.
■
The supply and return hoses must always be
secured with quick disconnects or caps to prevent
loss of fluids and contamination.
• Do not travel or turn with power unit lift arms
and attachment raised.
• Turn only on level ground.
• Go up and down slopes, not across them.
• Keep the heavy end of the machine uphill.
• Do not overload the machine.
■
Keep children and bystanders away from stor-
age area.
ꢀ Look down and to the rear and make sure area
is clear before operating in reverse.
12 Operation
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
PROBLEM
Drum will not rotate
POSSIBLE CAUSES
SOLUTION
Auxiliary hoses are not hooked up
to skid steer
Inspect connections visually (make
sure QD’s are fully engaged).
There is an obstruction in one or
both of the auxiliary hoses
Remove and inspect hoses
visually.
One or more seals on the motor
have failed
Contact dealer.
Skid steer auxiliary hydraulics are
not operating properly
Refer to skid steer owner’s
manual.
Motor hoses are not plumbed
correctly
See “Hydraulic Assembly TL52” on
page 22. Verify correct hose
routing.
Drum rotates sluggishly
Insufficient hydraulic flow from the
skid steer
Refer to skid steer owner’s
manual.
The hydraulic oil filter on the skid
steer is dirty
Refer to skid steer owner’s
manual.
One or more seals on the motor
have failed
Contact dealer.
Motor operates, but the drum does
not rotate
Cross bolt on coupler is sheared
Coupler splines are stripped
Motor shaft splines are stripped.
Inspect visually and repair as
needed.
Inspect visually and repair as
needed.
Inspect visually and repair as
needed.
Oil is leaking from the motor area.
One or more seals on the motor
have failed.
Contact dealer.
O-rings on fitting are damaged
Visually inspect o-rings and
replace as needed.
Fittings are loose or damaged
Refer to skid steer owner’s
manual.
Hydraulic hoses are loose or
damaged
Refer to skid steer owner’s
manual.
Insufficient cutting power
One or more seals on motor have
failed
Contact dealer.
Oil filter on the skid steer is dirty
Refer to skid steer owner’s
manual.
Insufficient auxiliary flow from skid
steer
Refer to skid steer owner’s
manual.
Relief valve on skid steer is not set
properly
Refer to skid steer owner’s
manual.
Troubleshooting 13
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSES
SOLUTION
Excessive oil temperature
Obstruction in one or both auxiliary
hoses
Visually inspect and replace hoses
as necessary.
Hydraulic oil level on skid steer is
low
Refer to skid steer owner’s
manual.
Hydraulic oil in skid steer is dirty
Refer to skid steer owner’s
manual.
Hydraulic oil filter on skid steer is
dirty
Refer to skid steer owner’s
manual.
Relief valve on skid steer is not set
properly
Refer to skid steer owner’s
manual.
Insufficient tilling power
The tines are worn or bent
Replaced damaged tines.
Debris has built up inside the
chassis
Clean debris from inside of
chassis.
Insufficient hydraulic flow from the
skid steer
Refer to skid steer owner’s
manual.
The hydraulic oil filter on the skid
steer is dirty
Refer to skid steer owner’s
manual.
One or more seals on the motor
have failed
Contact dealer.
14 Troubleshooting
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE
DRUM REMOVAL
Rotate the tiller so it rests on the attach wings as
shown in Figure 5. Use a hoist to support the drum at
the midpoint.
Figure 7.
Remove the coupler bolt (3) and the coupler (4) from
both sides of the drum as shown in Figure 8.
DP4
Figure 5.
Remove the two depth skid bolts (1) and four motor
housing bolts (2) from one side as shown in Figure 6.
4
2
1
3
Figure 8.
DP5
Figure 6.
MOTOR REMOVAL
Remove the depth skid and the motor housing from
one side as shown in Figure 7. Slide the drum off
remaining motor shaft.
Rotate the tiller so it rests on the attach wings as
shown in Figure 9. Use a hoist to support the drum at
the midpoint.
Service 15
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
Use an extension and a 1/2” twelve point socket to hold
motor bolts from the inside and remove the four 1/2”
nuts (4) from the bottom as shown in Figure 12.
DP4
Figure 9.
4
Remove the two depth skid bolts (1) and four motor
housing bolts (2) from one side as shown in Figure 10.
DP9
Figure 12.
2
MOTOR INSTALLATION
1
Place the motor housing into a vice (1). Install the
motor and orient the motor ports (2) as shown in Figure
13.
DP5
2
Figure 10.
Remove the depth skid and motor housing. Place the
motor housing in vice (3) as shown in Figure 11.
1
DP8
3
Figure 13.
Install four 1/2” - 20 x 1-1/2” twelve-point bolts (3) and
four 1/2” - 20 (4) nuts as shown in Figure 14 and Figure
16. While using an extension and 1/2” twelve-point
socket, hold bolts from the inside and torque nuts to 85
lbs-ft. (115 N-m).
DP8
Figure 11.
16 Service
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
DRUM INSTALLATION
Rotate the tiller chassis (1) so that it rests on the attach
bracket as shown in Figure 17.
Figure 14. TL52 and TL73
Install motor housing (5) into one side of the chassis
using four 1/2” x 1-1/2” bolts (6), eight 1/2” flat washers
(7) and four 1/2” - 13 nuts (8) as shown in Figure 15.
1
DP12
Figure 17.
Insert one coupler (2) into each end of the drum as
shown in Figure 18. Make sure the end nearest the
hole is to the inside. Line up the hole in the drum (3)
with the hole in the coupler and install one 1/2" x 3-3/4"
bolt (4) and one 1/2" - 20 nut (5).
Torque to 85 lbs-ft (115 N-m).
7
6
8
5
5
3
2
DP10
Figure 15.
4
DP7
Figure 18.
Install the motor housing (6) into one side of the chas-
sis using four 1/2" x 1-1/2" bolts (7), eight 1/2" flat
washers (8) and four 1/2" - 13 nuts (9) as shown in Fig-
ure 19. Torque to 120 lbs-ft (163 N-m).
Figure 16. TL84
Service 17
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
15
14
16
8
7
9
6
17
DP10
Figure 19
Use a hoist to lift the drum. Make sure the coupler is
aligned with the motor shaft and insert motor shaft into
drum as shown in Figure 20.
DP12
Figure 21.
Assemble the depth skid on either side of the chassis,
using an additional two 5/8" washers (18) and two 5/8"
nuts (19) for each side as shown in Figure 22. Torque
to 240 lbs-ft (325 N-m).
DP6
Figure 20.
Install the motor housing into other side of the chassis.
Install the motor housing (6) into one side of the chas-
sis using four 1/2" x 1-1/2" bolts (7), eight 1/2" flat
washers (8) and four 1/2" - 13 nuts (9) as shown in Fig-
ure 19. Torque to 120 lbs-ft (163 N-m).
18
19
Note: It may be necessary to rotate drum to allow the
splines on the coupler to align with the splines on the
motor shaft.
DEPTH SKID ASSEMBLY
Install two 5/8" x 4-1/2" bolts (14) and two 5/8" washers
(15) in each depth skid (17) as shown in Figure 21.
Slide the two bushings (16) onto the 5/8" bolts.
DP13
Figure 22.
18 Service
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
TINE REPLACEMENT
To replace worn or broken tines (1), remove the 1/2"
nut (3) and bolt (2) as shown in Figure 23. Remove the
worn or broken tine and replace with a new tine. Install
1/2" x 1-1/2" - 20 bolt (2) and 1/2" - 20 nut (3). Torque to
50 lbs-ft (68 N-m). The tine should rotate 15° when a
small force is applied to the tine. If the tine does not
rotate, loosen the nut until the tine is free to rotate.
3
2
1
Figure 23.
ꢁ
Service 19
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
DRUM ASSEMBLY
REF PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
1
1
1
2
2
2
59000
24 Bolt, 1/2 NF x 1-1/2 GR8 ZP TL52
24 Bolt, 1/2 NF x 1-1/2 GR8 ZP TL73
24 Bolt, 1/2 NF x 1-1/2 GR8 ZP TL84
3
3
3
4
4
4
101533
101533
101533
B0816
B0816
B0816
24 Tine, TL52
36 Tine, TL73
40 Tine, TL84
59000
59000
105170
101913
102402
1
1
1
Drum weld, 52" TL52
Drum weld, 73" TL73
Drum weld, 84" TL84
24 Nut, 1/2 - 20 Stover PLT TL52
36 Nut, 1/2 - 20 Stover PLT TL73
40 Nut, 1/2 - 20 Stover PLT TL84
(Rev. 4/4/2008)
20 Parts
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE UNIT ASSEMBLY
REF PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
Drum assembly TL73
1
2
3
4
5
6
7
7
7
20551
4
8
Bolt, 5/8 NC x 4-1/2 GR8 ZP
Bolt, 1/2 NC x 1-1/2 GR8 ZP
8
8
105899
1
1
2
1
2
1
8
2
2
4
8
21666
57816
105900
105901
S0100111
105902
1025864
B0815
Drum assembly TL84
16 Washer 1/2 SAE flat hrd
9
Housing/motor asy TL52/TL73
Seal kit (TL52/TL73 motor)
Housing/motor asy TL84
Seal Kit (TL84 motor)
101921
102993
104351
105715
105784
105786
2
2
4
1
1
1
Collar, round bore TL73
Skid
-
9
Bushing, TL Skid pin
Attach chassis TL52
Attach chassis TL73
Attach chassis TL84
-
10
11
12
13
14
Nut, 1/2 - 13 Stover plt GR5
Nut, 1/2 - 20 Stover plt GR5
Bolt, 1/2 x 3-3/4 - 20 GR8
Nut, 5/8 - 11 Stover UNC GR5
Washer, 5/8 flat SAE plt hrd
B0816
B0830
B1015
B1021
(Rev. 7/4/2008)
MAN0003 (Rev. 11/30/2006)
Parts 21
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC ASSEMBLY TL52
CONNECTION HOSE
END
1A
1B
2A
2B
3A
3B
H1265
H1265
H1264
H1264
H1281
H1281
-10 ST
-8 ST
ST
90°
ST
90°
REF PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
1
2
3
4
5
105716
2
4
4
2
1
Tube, 63.39 hyd TL52
6
7
-
HC414
1
2
2
2
2
QD 1/2" M Parker FE502-12 FO
Fitting 12 OM x 10 FLM ST
F1016
F1020
F1231
HC415
Fitting 10 OM x 8 FLM ST
Fitting 8 FLF x 8 FLM 90°
8 FLM x 8 FLM x 8 FLM
F1140
H1264
H1265
H1281
Hose #8 x 19" 8 FLF x 8 FLF 90° R2
Hose #10 x 52" 10 FLF x 8 FLF R2
Hose #8 x 21" 8 FLF x 8 FLF 90° R2
-
QD 1/2" F Parker FE501-12 FONL
-
(Rev. 4/4/2008)
MAN0003 (Rev. 11/30/2006)
22 Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC ASSEMBLY TL73
CONNECTION HOSE
END
1A
1B
2A
2B
3A
3B
H1280
H1280
H1278
H1278
H1279
H1279
-10 ST
-12 ST
ST
90°
ST
90°
REF PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
1
2
3
4
5
101897
2
2
4
2
2
Tube, hyd TL73
6
7
8
-
F1006
2
1
1
2
2
2
Fitting, 12 OM x 12 FLM
102360
F1087
F1110
F1232
Tube, hyd TL73/TL84
HC414
HC415
H1278
H1279
H1280
QD 1/2" M Parker FE502-12FO
QD 1/2" F Parker FE501-FONL
Hose #10 x 19" 10 FLF x 10 FLF 90°
Hose #10 x 21" 10 FLF x 10 FLF 90°
Hose #10 x 21" 10 FLF x 10 FLF 90°
Fitting, 10 OM x 10 FLM ST
Fitting, 10 FLM x 10 FLF 90°
Fitting, 10 FLM x 10 FLF x 10 FLM
-
-
(Rev. 4/4/2008)
MAN0003 (Rev. 11/30/2006)
Parts 23
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC ASSEMBLY TL84
CONNECTION HOSE
END
1A
1B
2A
2B
3A
3B
H1337
H1337
H1335
H1335
H1336
H1336
ST
ST
ST
90°
ST
90°
REF PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
1
2
3
4
5
102746
2
2
2
2
4
Tube, hyd TL84
6
7
8
-
F1006
2
1
1
2
2
2
Fitting, 12 OM x 12 FLM
102747
F1023
F1077
F1089
Tube, hyd TL84
HC415
HC414
H1335
H1336
H1337
QD 1/2" F Parker FE501-FONL
QD 1/2" M Parker FE502-12FO
Hose #12 x 19" 12 FLF x 12 FLF
Hose #12 x 21" 12 FLF x 12 FLF 90°
Hose #12 x 84" 12 FLF x 12 FLF
Fitting, 12 FLF x 12 FLM 90°
Fitting, 12 FLM x 12 FLF x 12 FLM
Fitting, 12 FLM x 10 OM ST
-
-
(Rev. 4/4/2008)
MAN0003 (Rev. 11/30/2006)
24 Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
DECAL PLACEMENT
REF PART QTY
DESCRIPTION
1
2
2
2
3
4
D0119
D0155
D0161
D0264
D0157
D0158
1
1
1
1
1
2
Decal, Alitec (white with black)
Decal, TL52
Decal, TL73
Decal, TL84
Decal, tie down
Decal, lift point
Parts 25
MAN0003 (Rev. 11/30/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
FITTING TORQUE CHART
Always tighten fittings to these values unless a different torque value is listed
for a specific service procedure.
Make sure fastener threads are clean and threads are engaged properly.
All torque values are adopted from SAE J514 and SAE J1453.
SAE (JIC)
37° Flare Thread
Size
O-Ring Style
Straight Thread
Size
Seal-Lok
Thread
Size
2
5/16 - 24
3/8 - 24
5/16 - 24
3/8 - 24
---
---
3
4
7/16 - 20
1/2 - 20
7/16 - 20
1/2 - 20
9/16 - 18
---
5
6
9/16 - 18
3/4 - 16
9/16 - 18
3/4 - 16
11/16 - 16
13/16 - 16
1 - 14
8
10
12
14
16
20
24
32
7/8 - 14
7/8 - 14
1-1/16 - 12
1-3/16 - 12
1-5/16 - 12
1-5/8 - 12
1-7/8 - 12
2-1/2 - 12
1-1/16 - 12
1-3/16 - 12
1-5/16 - 12
1-5/8 - 12
1-7/8 - 12
2-1/2 - 12
1-3/16 - 12
---
1-7/16 - 12
1-11/16 - 12
2 - 12
---
TORQUE
SAE
Dash
Size
SAE 37° Flare
O-Ring Straight Thread
Seal-Lok
Lbs-Ft
4
N-m
5
Lbs-Ft
4
N-m
5
Lbs-Ft
---
N-m
---
2
3
8
11
9
12
---
---
4
12
16
16
22
18
25
5
15
20
22
30
---
---
6
18
25
35
48
27
37
8
37
50
60
82
40
54
10
12
14
16
20
24
32
48
65
105
140
184
221
258
317
---
143
190
250
300
350
430
---
63
86
74
100
120
135
180
225
320
92
125
---
88
---
100
133
166
236
122
147
166
---
165
200
225
---
26 Appendix
Fitting Torque Chart (7/15/2005)
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK COUPLER KITS
High-Flow with Auxiliary
High-Flow with No Auxiliary
Low-Flow
Description
Make
QC Kit
Description
QC Kit
Description
QC Kit
HC357
HC243
HC211
Bobcat
HC356
Flush Face
HC355
Flush Face
Flush Face
Poppet
Ag Ball Valve
Case
1013825
HC278
HC209
Flush Face
Flush Face
HC212
Flush Face
HC279
HC211
Flush Face
Ag Ball Valve
Flush Face &
Ag Ball Valve
Cat
Daewoo
Gehl
HC538
HC209
HC398
Flush Face
Flush Face
Flush Face
1014196
HC212
Flush Face
Flush Face
Flush Face
1014197
HC211
Flush Face
Ag Ball Valve
Flush Face
1014195
HC305
HC400
Poppet &
Ag Ball
John Deere
Komatsu
1014198
1013834
1014199
HC537
Flush Face
Flush Face
Flush Face
Flush Face
1013826
1013833
HC308
Flush Face
Flush Face
Flush Face
HC310
1013835
HC310
HC243
Flush Face
Flush Face
Flush Face
Poppet
New Holland
Scat Trak
QUICK COUPLER KIT COMPONENTS
QC KIT
Includes
Style
Male/Female
Body
Size
Hose End
HC209
HC193
HC194
HC195
HC196
HC197
HC195
HC196
HC193
HC194
HC197
HC193
HC194
HC197
HC201
HC197
HC201
Flush Face
Flush Face
Ag Ball
Male
Female
Female
Male
3/4
3/4
1/2
1/2
1/2
1/2
1/2
3/4
3/4
1/2
3/4
3/4
1/2
1/2
1/2
1/2
SAE #12 O-ring
SAE #12 O-ring
1/2-14 NPT
Ag Ball
1/2-14 NPT
Flush Face
Ag Ball
Female
Female
Male
SAE #10 O-ring
1/2-14 NPT
HC211
HC212
Ag Ball
1/2-14 NPT
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Male
SAE #12 O-ring
SAE #12 O-ring
SAE #10 O-ring
SAE #12 O-ring
SAE #12 O-ring
SAE #10 O-ring
SAE #10 O-ring
SAE #10 O-ring
SAE #10 O-ring
Female
Female
Male
HC278
HC279
Female
Female
Male
Female
Male
Quick Coupler 27
Quick Coupler Chart (Rev. 10/20/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK COUPLER KIT COMPONENTS
QC KIT
Includes
Style
Male/Female
Body
Size
Hose End
HC308
HC416
HC417
HC418
HC414
HC415
HC344
HC345
HC346
HC342
HC343
HC344
HC345
HC346
HC344
HC345
HC344
HC345
HC346
HC344
HC345
HC415
HC416
HC417
HC418
HC521
HC522
1532994
1532995
1532997
HC417
HC418
HC545
HC546
HC547
HC343
HC521
HC522
HC415
HC521
HC522
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Female
Male
5/8
5/8
3/8
1/2
1/2
SAE #12 O-ring
SAE #12 O-ring
SAE #8 O-ring
SAE #12 O-ring
SAE #12 O-ring
Male
HC310
HC355
Male
Female
Male
12 mm SAE #12 O-ring
12 mm SAE #12 O-ring
Female
Female
Female
Male
9 mm
7 mm
7 mm
SAE #8 O-ring
SAE #6 O-ring
SAE #6 O-ring
HC356
Male
12 mm SAE #12 O-ring
12 mm SAE #12 O-ring
Female
Female
Male
9 mm
SAE #8 O-ring
HC357
HC398
12 mm SAE #12 O-ring
12 mm SAE #12 O-ring
12 mm SAE #12 O-ring
12 mm SAE #12 O-ring
Female
Male
Female
Female
Male
9 mm
SAE #8 O-ring
HC400
HC537
12 mm SAE #12 O-ring
12 mm SAE #12 O-ring
Female
Female
Female
Male
1/2
5/8
5/8
3/8
SAE #12 O-ring
SAE #12 O-ring
SAE #12 O-ring
SAE #8 O-ring
Male
HC538
Female
Male
16 mm SAE #12 O-ring
16 mm SAE #12 O-ring
Female
Male
3/4
3/4
SAE #12 O-ring
SAE #12 O-ring
SAE #8 O-ring
SAE #12 O-ring
SAE #8 O-ring
SAE #12 O-ring
SAE #10 O-ring
SAE #10 O-ring
SAE #6 O-ring
Female
Male
1/2
1013825
5/8
Male
3/8
Female
Female
Male
5/8
1/2
1/2
1013826
1013833
Male
7 mm
Female
Male
16 mm SAE #12 O-ring
16 mm SAE #12 O-ring
Female
Female
Male
1/2
SAE #12 O-ring
16 mm SAE #12 O-ring
16 mm SAE #12 O-ring
28 Quick Coupler
Quick Coupler Chart (Rev. 10/20/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK COUPLER KIT COMPONENTS
QC KIT
Includes
Style
Male/Female
Body
Size
Hose End
1013834
HC414
HC415
HC521
HC522
46058
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Flush Face
Male
Female
Female
Male
1/2
1/2
SAE #12 O-ring
SAE #12 O-ring
16 mm SAE #12 O-ring
16 mm SAE #12 O-ring
1013835
1014195
M/F Set
Male
3/4
SAE #12 O-ring
HC344
HC345
HC346
HC521
HC522
1532997
1532994
1532995
HC343
HC414
HC415
HC521
HC522
HC414
HC415
HC416
HC417
HC418
12 mm SAE #12 O-ring
12 mm SAE #12 O-ring
Female
Female
Female
Male
9 mm
SAE #8 O-ring
1014196
16 mm SAE #12 O-ring
16 mm SAE #12 O-ring
Female
Female
Male
1/2
3/4
SAE #8 O-ring
SAE #10 O-ring
SAE #10 O-ring
SAE #6 O-ring
SAE #12 O-ring
SAE #12 O-ring
1014197
1014198
3/4
Male
7 mm
1/2
Male
Female
Female
Male
1/2
16 mm SAE #12 O-ring
16 mm SAE #12 O-ring
1014199
Male
1/2
1/2
5/8
5/8
3/8
SAE #12 O-ring
SAE #12 O-ring
SAE #12 O-ring
SAE #12 O-ring
SAE #8 O-ring
Female
Female
Male
Male
Quick Coupler 29
Quick Coupler Chart (Rev. 10/20/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
A
SAE 2
SAE 5
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
8
lbs-ft
10
N-m
13
lbs-ft
14
N-m
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
7/16"
1/2"
6
18
37
12
17
19
26
27
9/16"
5/8"
23
31
35
47
49
67
36
48
55
75
78
106
163
232
325
569
907
1383
3/4"
55
75
85
115
164
230
403
642
979
120
171
240
420
669
1020
13/16"
15/16"
1-1/8"
1-5/16"
1-1/2"
78
106
149
261
416
634
121
170
297
474
722
110
192
306
467
METRIC SERIES
TORQUE
CHART
8.8
Metric Bolt Head
Identification
10.9
A
Metric
Grade 8.8
Metric
Grade 10.9
COARSE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft
FINE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft
A
A
Diameter &
Thread Pitch Wrench
(Millimeters)
Diameter &
Thread Pitch
(Millimeters)
Size
N-m
lbs-ft
6
N-m
lbs-ft
6
6 x 1.0
10 mm
13 mm
16 mm
18 mm
21 mm
24 mm
27 mm
30 mm
34 mm
36 mm
46 mm
8
11
27
8
8
11
29
8
6 x 1.0
8 x 1.0
8 x 1.25
10 x 1.5
12 x 1.75
14 x 2.0
16 x 2.0
18 x 2.5
20 x 2.5
22 x 2.5
24 x 3.0
30 x 3.0
20
15
20
21
16
22
39
29
54
40
41
30
57
42
10 x 1.25
12 x 1.25
14 x 1.5
16 x 1.5
18 x 1.5
20 x 1.5
22 x 1.5
24 x 2.0
30 x 2.0
68
50
94
70
75
55
103
163
250
363
507
684
861
1740
76
109
169
234
330
451
571
1175
80
151
234
323
457
623
790
1626
111
173
239
337
460
583
1199
118
181
263
367
495
623
1258
87
120
184
268
374
505
635
1283
125
172
244
332
421
867
133
194
270
365
459
928
Typical Washer
Installations
Bolt
Flat Washer
Lock Washer
8/9/00
Bolt Torque & Size Charts (Rev. 3/28/2007)
30 Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
5/8
3/4
7/8
IN
1
2
7
3
4
5
6
MM
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM 10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG .............................................................. Agriculture
MPa.........................................................Mega Pascal
N.......................................................................Newton
NC......................................................National Coarse
NF ...........................................................National Fine
NPSM.....................National Pipe Straight Mechanical
NPT.......................................... National Pipe Tapered
NPT SWF .........National Pipe Tapered Swivel Female
ORBM .......................................... O-Ring Boss - Male
P...........................................................................Pitch
PBY...................................................... Power-Beyond
psi..........................................Pounds per Square Inch
PTO..................................................... Power Take Off
QD....................................................Quick Disconnect
RH..............................................................Right Hand
ROPS........................... Roll-Over Protective Structure
RPM ........................................Revolutions Per Minute
RT ....................................................................... Right
SAE..........................Society of Automotive Engineers
UNC .....................................................Unified Coarse
UNF...........................................................Unified Fine
UNS......................................................Unified Special
ASABE.................... American Society of Agricultural &
Biological Engineers (formerly ASAE)
ASAE ....... American Society of Agricultural Engineers
ATF ............................... Automatic Transmission Fluid
BSPP .............................British Standard Pipe Parallel
BSPTM ................British Standard Pipe Tapered Male
CV.....................................................Constant Velocity
CCW .............................................. Counter-Clockwise
CW............................................................... Clockwise
F ...................................................................... Female
FT .............................................................. Full Thread
GA .................................................................... Gauge
GR (5, etc.) ........................................... Grade (5, etc.)
HHCS ........................................Hex Head Cap Screw
HT........................................................... Heat-Treated
JIC .................Joint Industry Council 37° Degree Flare
LH.................................................................Left Hand
LT........................................................................... Left
m......................................................................... Meter
mm................................................................Millimeter
M.......................................................................... Male
Bolt Torque & Size Charts (Rev. 3/28/2007)
Appendix 31
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________
Model Number: ____________________________
From (Dealer): ___________________________________________
Serial Number: ___________________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set
forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
Woods backhoe models BH70-X, BH80-X, and BH90-X are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted
Duration (from date of delivery
Model Number
to the original purchaser)
BW1260, BW1800
8 years
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X,
BB7200X, BB8400X, DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3
6 years
Gearbox
components
PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2,
RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2, 5 years
9204RD-2, S15CD, S20CD, S22CD, S25CD, S27CD
3 years (1 year if used in rental or
commercial applications)
RDC54, RD60, RD72
RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2,
9180RD-2, 9204RD-2
Blade spindles
Rust-through
3 years
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW180-3,
BW1260, BW1800, 2162, 3240, DS1260, DSO1260, DS1440, TS1680
10 years
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been
materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized
service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made
with parts other than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to
a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS,
in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof
of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS
WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business,
revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute
machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS,
its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-3079 (Rev. 5/15/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(Replacement Parts For All Models Except Mow’n Machine
Zero-Turn Mowers and Woods Boundary Utility Vehicles)
TM
TM
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a
period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This
Warranty does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser
in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)
days after such defect or noncompliance is discovered or should have been discovered, routed through
the dealer and distributor from whom the purchase was made, transportation charges prepaid.
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising
directly or indirectly from the product, whether such claim is based upon breach of contract, breach
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to
obtain materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized
to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-8494 (Rev. 6/23/2005)
Download from Www.Somanuals.com. All Manuals Search And Download.
PART NO.
MAN0003
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
© 2002 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual
are the property of their respective companies or mark holders. Specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|