Woods Equipment Compact Loader 211716 User Manual

211716 LOADER MOUNTING KIT  
for 1009, 1012, LC96, LC102 Loaders  
on John Deere® FWA, ROPS Tractors  
3120, 3320, 3520, 3720  
& 3203  
Includes Hose Kit  
1019027  
Tested. Proven. Unbeatable.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!  
Make sure that all operating and service person-  
nel know that if hydraulic fluid penetrates skin, it  
LEA EL INSTRUCTIVO!  
must be surgically removed as soon as possible by  
!
Si no lee Ingles, pida ayuda a  
alguien que si lo lea para que le  
traduzca las medidas de seguridad.  
a doctor familiar with this form of injury or gan-  
grene, serious injury, or death will result. CON-  
TACT A PHYSICIAN IMMEDIATELY IF FLUID  
ENTERS SKIN OR EYES. DO NOT DELAY.  
Check that all hardware is properly installed.  
Always tighten to torque chart specifications  
unless instructed otherwise in this manual.  
Safety is a primary concern in the design and  
manufacture of our products. Unfortunately, our  
efforts to provide safe equipment can be wiped  
out by an operator’s single careless act.  
Air in hydraulic systems can cause erratic oper-  
ation and allows loads or equipment components  
to drop unexpectedly. When connecting equipment  
or hoses or performing any hydraulic maintenance,  
purge any air in hydraulic system by operating all  
hydraulic functions several times. Do this before  
putting into service or allowing anyone to  
approach the equipment.  
In addition to the design and configuration of  
equipment, hazard control and accident preven-  
tion are dependent upon the awareness, con-  
cern, judgement, and proper training of  
personnel involved in the operation, transport,  
maintenance, and storage of equipment.  
It has been said, “The best safety device is an  
informed, careful operator.” We ask you to be  
that kind of operator.  
Protective hose sleeves must cover all hydrau-  
lic hoses within 20 inches of the operator and be  
secured onto metal hose fittings. Replace hoses or  
sleeves if damaged or if protective sleeve cannot  
be properly positioned or secured.  
INSTALLATION  
This Loader Mounting Kit is to be used only for  
the loaders and tractors specified in this manual.  
Any other use or modification of this mounting kit  
may result in serious injury or death.  
Make sure all hydraulic hoses, fittings, and  
valves are in good condition and not leaking before  
starting power unit or using equipment. Check and  
route hoses carefully to prevent damage. Hoses  
must not be twisted, bent sharply, kinked, frayed,  
pinched, or come into contact with any moving  
parts. Operate moveable components through full  
operational range to check clearances. Replace  
any damaged hoses immediately.  
Hydraulics must be connected as instructed in  
this manual. Do not substitute parts, modify, or  
connect in any other way.  
After connecting hoses, check that all control  
lever positions function as instructed in the Opera-  
tor's Manual. Do not put into service until control  
lever and equipment movements are correct.  
Always wear relatively tight and belted clothing  
to avoid getting caught in moving parts. Wear  
sturdy, rough-soled work shoes and protective  
equipment for eyes, hair, hands, hearing, and head;  
and respirator or filter mask where appropriate.  
Safety instructions are important! Read all  
attachment and power unit manuals; follow all  
safety rules and safety decal information. (Replace-  
ment manuals and safety decals are available from  
your dealer. To locate your nearest dealer, check  
or in the United States and Canada call 1-800-319-  
6637.) Failure to follow instructions or safety rules  
can result in serious injury or death.  
Do not modify or alter or permit anyone else to  
modify or alter the equipment or any of its compo-  
nents in any way.  
Do not allow bystanders in the area when oper-  
ating, attaching, removing, assembling, or servic-  
ing equipment.  
Use a suitable lifting device of sufficient capac-  
ity. Use adequate personnel to handle heavy com-  
ponents.  
Keep all persons away from operator control  
area while performing adjustments, service, or  
maintenance.  
Keep hands and body away from pressurized  
lines. Use paper or cardboard, not hands or other  
body parts to check for leaks. Wear safety goggles.  
Hydraulic fluid under pressure can easily penetrate  
skin and will cause serious injury or death.  
Loader Mounting Kit SR3 (11/1/2002)  
3 Safety  
Download from Www.Somanuals.com. All Manuals Search And Download.  
211716 LOADER MOUNTING KIT  
Tractor Preparation  
For installing this mounting kit, references to right, left,  
forward, and rearward directions are determined from  
the operator’s position in the tractor seat.  
Only use 211716 Loader Mounting Kit for  
Leave all hardware loose until loader mount is com-  
pletely assembled. When assembly is completed,  
torque hardware to specifications listed on page 7 of  
this manual.  
mounting Woods 1009, 1012, LC96 and LC102  
loaders on John Deere® 3120, 3320, 3520, 3720 &  
3203 FWA ROPS tractors. Any other use or modi-  
fication of this mounting kit may result in serious  
injury or death.  
1. Shut off engine and set parking brake during  
installation.  
IMPORTANT  
This equipment must be assembled and  
2. Remove the tractor front weights and front weight  
bracket, if equipped.  
installed on the customer’s tractor by the Woods  
dealer. Dealer must thoroughly inspect equipment  
and complete each item on the PRE-DELIVERY  
CHECK LIST, DELIVERY CHECK LIST, and PROD-  
UCT REGISTRATION before equipment is  
released to the customer.  
3. The tractor must be equipped with single multi-  
function control lever (joystick) and hydraulic cou-  
plers, available through John Deere.  
4. Larger tires may require steering stop adjustment.  
Tires must clear loader and loader mounts at full  
oscillation and full turn. See your tractor opera-  
tor's manual for instructions on steering stop  
adjustment.  
Clean threaded holes in the tractor chassis  
thoroughly, using a tap of the proper size. Paint,  
rust or debris in the threads may not permit cap  
screws to be installed and tightened correctly.  
Remove Hydraulic Coupler Bracket  
Remove Hardware  
and Coupler Bracket  
1. Locate tractor female hydraulic couplers located  
in front of the right operator platform.  
2. Disconnect hydraulic couplers from hydraulic  
lines. Identify the lines with a color code so that  
they can be reinstalled in the same location.  
3. Remove snap rings on back side of coupler  
bracket and remove hydraulic couplers from cou-  
pler bracket.  
4. Remove two cap screws from tractor housing and  
remove coupler bracket shown in Figure 1.  
DP1  
Figure 1. Remove Hydraulic Coupler Bracket  
(Rev. 9/29/2011)  
4 Mount Installation  
MAN0426 (3/3/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Install Coupler and Hose Line Brackets  
1. Insert hydraulic couplers through new coupler  
bracket (2) and secure with snap rings.  
NOTE: Make sure hydraulic couplers are in the  
same color sequence as they were when they  
were removed.  
2. Connect couplers to the hydraulic feed lines.  
3. Attach coupler bracket to tractor chassis using  
hardware previously removed.  
2. 1019032 Bracket, hydraulic coupler  
Figure 2. Hydraulic Coupler Bracket Installed  
Install Right and Left Rear Mounts  
1. Attach right rear mount (1) to tractor housing  
using four cap screws (12) and hardened flat  
washers (11).  
2. Repeat process for installation of left mount (2).  
1. 1019010 Right rear mount  
2. 1019011 Left rear mount  
11.  
12.  
57817 5/8 Hardened flat washer  
64062 M16 x 2.0P x 40 mm HHCS  
Figure 3. Rear Mount Installation  
Mount Installation 5  
MAN0426 (3/3/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Install Right and Left Front Mounts  
1. Install right (4) and left front mounts (5) to front of  
tractor using eight (four per side) cap screws (7),  
flat washers (10), and hex nuts (8).  
2. Position cap screws on the outside of mount with  
flat washers and hex nuts on the inside of tractor  
frame.  
4. 1034180 Right front mount  
5. 1034181 Left front mount  
7. 307301 M12 x 1.75P x 40 mm HHCS  
8. 307813 M12 x 1.75 Hex nut  
10.  
57816 1/2 Hardened flat washer  
Figure 4. Front Mount Installation  
Install Side Rails  
1. Attach front end of right side rail (3) to outside of  
1. 1019010 Right rear mount  
3. 1019013 Side rail  
front mount (4).  
4. 1019018 Right front mount  
2. Secure with two carriage bolts (9), flat washers  
(11), and hex nuts (6).  
6.  
9.  
230 5/8 Hex nut  
5607 5/8 NC x 1-1/2 Carriage bolt  
57817 5/8 Hardened flat washer  
3. Attach side rails to the inside (between tractor  
and mount) of right rear mount (1) using three  
carriage bolts (9), flat washers (11), and hex nuts  
(6).  
11.  
4. Repeat steps for installation of left side rail.  
Figure 6. Left Side Rail Installed  
Figure 5. Right Side Rail Installation  
(Rev. 9/29/2011)  
MAN0426 (3/3/2006)  
6 Mount Installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Torque Hardware  
Torque all mounting hardware to specifications given  
below.  
TORQUE SPECIFICATIONS  
Wrench  
Ref  
7
Cap Screw  
Qty  
Size  
18 mm  
15/16  
Required Torque  
50 lbs-ft. (68 N-m)  
170 lbs-ft. (230 N-m)  
125 lbs-ft. (169 N-m)  
M12 x 1.75P x 40 mm  
8
9
5/8 NC x 1-1/2 Carriage bolt GR5  
M16 x 2.0P x 40 mm  
10  
8
12  
24 mm  
Install Grill Guard (Optional)  
1. Align grill guard (A) with holes on front of tractor  
frame and secure into position using four cap  
screws (B), hardened flat washers (D), and hex  
nuts (C).  
A. 1019012 Grill guard -  
(Includes hardware B, C & D)  
B. 307301 M12 x 1.75P x 40 mm HHCS  
C. 307813 M12 x 1.75 Hex nut  
2. Torque to 50 lbs-ft.  
D.  
57816 1/2 Hardened flat washer  
Figure 7. Grill Guard Installation  
Figure 8. Grill Guard Installed  
As a valued customer, Woods appreciates your comments. Once loader mount and  
hydraulic hoses have been installed, please take a few minutes to complete the Loader  
Mount Evaluation sheet that was supplied with this mount. Your comments will help us  
continue to bring you quality products.  
Mount Installation 7  
MAN0426 (3/3/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1019027 HOSE KIT INSTALLATION  
General Description  
These instructions are for operating the loader using  
the tractor hydraulic remote control lever. To use this  
hydraulic connection, the tractor must be equipped  
with the manufacturer’s multi-function hydraulic lever  
and four tractor hydraulic couplers.  
Figure 9. Tractor Remote Control Connections  
Assemble Hoses  
Attach 45-degree elbow (3) and male quick coupler  
(8) to the end of the four loader supply hoses (1). See  
Figure 10.  
1. 1018142 Hose, 46" x 3/8 NPTM x 3/4 JICM  
3. 313015 Elbow, 3/8 NPTM x 3/8 NPTF 45°  
8.  
64300 Quick coupler, male 3/8  
Figure 10. Hose Kit Assembly  
Connect Hoses to Loader  
1. Connect the loader supply hoses to loader steel  
feedlines.  
2. Follow color code listed in Figure 11.  
Figure 11. Loader Feedline Identification  
8 Hydraulic Installation  
MAN0426 (3/3/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connect Hoses to Tractor  
1. Connect hydraulic hoses to tractor hydraulic  
couplers as shown in Figure 12.  
2. Attach color coded plastic bands around male  
quick couplers to identify quick coupler  
connections.  
Figure 12. Hydraulic Hose Connection  
Verification of Control Movements  
1. Mount loader to tractor: Remove mount pins  
from loader uprights. Align tractor with loader and  
slowly drive tractor into loader. Shut off tractor.  
9. Be sure that adequate slack is left in the hoses so  
they can move as the loader moves through its  
full range of motion.  
2. Connect loader feedline hoses to tractor hydraulic  
remote control hydraulic couplers. See Figure 12  
for hose connections.  
10. Before operating the loader, make sure that the  
Pre-Delivery, Delivery, and Pre-Operation Check  
Lists from the Loader Operator’s Manual have  
been completed.  
3. Mount loader to tractor by activating bucket  
cylinders to raise or lower the loader uprights into  
the loader mounts. Slowly drive tractor forward,  
activating appropriate cylinders to engage loader  
completely into mounts. Insert mounting pins to  
secure loader.  
4. Comply with all Safety Rules and start the tractor.  
5. Check that all hydraulic control lever positions  
operate the loader movements correctly as  
shown in Figure 13.  
6. If loader movements do not respond correctly,  
shut off tractor, relieve pressure, and reconnect  
properly. Loader control movements must be  
correct before proceeding.  
Handle Forward - Boom down  
7. Once all loader functions are correct, start the  
tractor and operate the loader to check for leaks.  
Purge any remaining air from the hydraulic  
system and check oil level.  
Handle forward to limit - Float position  
Handle back - Boom up  
Handle to right - Dump bucket or attachment  
Handle to left - Rollback bucket or attachment  
8. When hose routings and correct loader  
operations are verified, place a matching colored  
band around male and female quick-disconnect  
couplers. The colored bands will make re-  
installation easier when the loader is removed  
from the tractor.  
Figure 13. Single Lever Control Operation  
MAN0426 (3/3/2006)  
Hydraulic Installation 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
211716 LOADER MOUNTING KIT  
1019012 Grill Guard (Optional)  
REF PART  
QTY  
DESCRIPTION  
REF PART  
QTY  
DESCRIPTION  
Right rear mount  
A
B
C
D
1019012  
1
4
4
4
Grill guard, includes items B - D  
M12 x 1.75P x 40 mm HHCS  
M12 x 1.75P Hex nut  
1
2
1019010  
1
1
2
1
1
307301  
307813  
57816  
1019011  
1019013  
1034180  
1034181  
Left rear mount  
Side rail  
3
1/2 Hardened flat washer  
4
Right front mount  
Left front mount  
5
6
230 * 10 5/8 NC Hex nut  
7
307301  
307813  
8
8
M12 x 1.75P x 40 mm HHCS  
M12 x 1.75P Hex nut  
8
9
5607 * 10 5/8 NC x 1-1/2 Carriage bolt  
57816 1/2 Hardened flat washer  
57817 18 5/8 Hardened flat washer  
64062 M16 x 2.0P x 40 mm Cap screw  
10  
11  
12  
8
8
* Standard hardware, obtain locally  
(Rev. 9/29/2011)  
10 Parts  
MAN0426 (3/3/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1019027 HOSE KIT  
REF PART  
QTY  
DESCRIPTION  
1
2
1018142  
4
1
4
2
2
2
2
4
Hose, 46" x 3/8 NPTM x 3/4 JICM  
Bracket, coupler  
1019032  
313015  
395061  
395062  
56061  
3
Elbow, 3/8 NPTM x 3/8 NPTF 45°  
Plastic spiral band, red  
4
5
Plastic spiral band, blue  
Plastic spiral band, green  
Plastic spiral band, yellow  
Quick coupler, male 3/8  
6
7
56062  
8
64300  
NS  
88 * AR Plastic tie  
* Standard hardware, obtain locally  
NS Not shown  
AR As required  
Parts 11  
MAN0426 (3/3/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BOLT TORQUE CHART  
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific  
application.  
Fasteners must always be replaced with the same grade as specified in the manual parts list.  
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.  
Make sure fastener threads are clean and you start thread engagement properly.  
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.  
SAE Bolt Head  
Identification  
SAE SERIES  
TORQUE  
CHART  
A
SAE Grade 2  
(No Dashes)  
SAE Grade 8  
(6 Radial Dashes)  
SAE Grade 5  
(3 Radial Dashes)  
MARKING ON HEAD  
A
SAE 2  
SAE 5  
SAE 8  
Diameter  
(Inches)  
Wrench  
Size  
lbs-ft  
N-m  
8
lbs-ft  
10  
N-m  
13  
lbs-ft  
14  
N-m  
1/4"  
5/16"  
3/8"  
7/16"  
1/2"  
9/16"  
5/8"  
3/4"  
7/8"  
1"  
7/16"  
1/2"  
6
18  
37  
12  
17  
19  
26  
27  
9/16"  
5/8"  
23  
31  
35  
47  
49  
67  
36  
48  
55  
75  
78  
106  
163  
232  
325  
569  
907  
1383  
3/4"  
55  
75  
85  
115  
164  
230  
403  
642  
979  
120  
171  
240  
420  
669  
1020  
13/16"  
15/16"  
1-1/8"  
1-5/16"  
1-1/2"  
78  
106  
149  
261  
416  
634  
121  
170  
297  
474  
722  
110  
192  
306  
467  
METRIC SERIES  
TORQUE  
CHART  
8.8  
Metric Bolt Head  
Identification  
10.9  
A
Metric  
Grade 8.8  
Metric  
Grade 10.9  
COARSE THREAD  
FINE THREAD  
A
A
MARKING ON HEAD  
MARKING ON HEAD  
Diameter &  
Thread Pitch Wrench  
(Millimeters)  
Diameter &  
Thread Pitch  
(Millimeters)  
Metric 8.8  
Metric 10.9  
N-m lbs-ft  
Metric 8.8  
Metric 10.9  
N-m lbs-ft  
Size  
N-m  
lbs-ft  
6
N-m  
lbs-ft  
6
6 x 1.0  
10 mm  
13 mm  
16 mm  
18 mm  
21 mm  
24 mm  
27 mm  
30 mm  
34 mm  
36 mm  
46 mm  
8
11  
27  
8
8
11  
29  
8
6 x 1.0  
8 x 1.0  
8 x 1.25  
10 x 1.5  
12 x 1.75  
14 x 2.0  
16 x 2.0  
18 x 2.5  
20 x 2.5  
22 x 2.5  
24 x 3.0  
30 x 3.0  
20  
15  
20  
21  
16  
22  
39  
29  
54  
40  
41  
30  
57  
42  
10 x 1.25  
12 x 1.25  
14 x 1.5  
16 x 1.5  
18 x 1.5  
20 x 1.5  
22 x 1.5  
24 x 2.0  
30 x 2.0  
68  
50  
94  
70  
75  
55  
103  
163  
250  
363  
507  
684  
861  
1740  
76  
109  
169  
234  
330  
451  
571  
1175  
80  
151  
234  
323  
457  
623  
790  
1626  
111  
173  
239  
337  
460  
583  
1199  
118  
181  
263  
367  
495  
623  
1258  
87  
120  
184  
268  
374  
505  
635  
1283  
125  
172  
244  
332  
421  
867  
133  
194  
270  
365  
459  
928  
Typical Washer  
Installations  
Bolt  
Flat Washer  
Lock Washer  
8/9/00  
Bolt Torque & Size Charts (Rev. 10/10/2005)  
12 Appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BOLT SIZE CHART  
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.  
SAE Bolt Thread Sizes  
5/16  
3/8  
1/2  
5/8  
3/4  
7/8  
IN  
1
2
7
3
4
5
6
MM  
25  
50  
75  
100  
125  
150  
175  
Metric Bolt Thread Sizes  
8MM 10MM  
12MM  
14MM  
16MM  
18MM  
ABBREVIATIONS  
AG.............................................................Agriculture  
ATF...............................Automatic Transmission Fluid  
BSPP .......................... British Standard Pipe Parallel  
BSPTM...............British Standard Pipe Tapered Male  
CV.................................................. Constant Velocity  
CCW ............................................ Counter-Clockwise  
CW............................................................. Clockwise  
F..................................................................... Female  
GA................................................................... Gauge  
GR (5, etc.) .........................................Grade (5, etc.)  
HHCS.......................................Hex Head Cap Screw  
HT ......................................................... Heat-Treated  
JIC............... Joint Industry Council 37° Degree Flare  
LH ...............................................................Left Hand  
LT ......................................................................... Left  
m.......................................................................Meter  
mm ..............................................................Millimeter  
M........................................................................ Male  
MPa........................................................Mega Pascal  
N ....................................................................Newton  
NC ....................................................National Coarse  
NF......................................................... National Fine  
NPSM ...................National Pipe Straight Mechanical  
NPT ........................................ National Pipe Tapered  
NPT SWF .......National Pipe Tapered Swivel Female  
ORBM......................................... O-Ring Boss - Male  
P .........................................................................Pitch  
PBY .................................................... Power-Beyond  
psi........................................Pounds per Square Inch  
PTO ................................................... Power Take Off  
QD ..................................................Quick Disconnect  
RH ............................................................Right Hand  
ROPS..........................Roll-Over Protective Structure  
RPM.......................................Revolutions Per Minute  
RT...................................................................... Right  
SAE ........................Society of Automotive Engineers  
UNC....................................................Unified Coarse  
UNF ........................................................ Unified Fine  
UNS....................................................Unified Special  
Bolt Torque & Size Charts (Rev. 10/10/2005)  
Appendix 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY  
(Replacement Parts For All Models Except Mow’n Machine  
Zero-Turn Mowers and Woods Boundary Utility Vehicles)  
TM  
TM  
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and  
workmanship for a period of ninety (90) days from the date of delivery of the product to the original  
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a  
period of 12 months.  
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of  
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This  
Warranty does not cover normal wear or tear, or normal maintenance items.  
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell  
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser  
in any way. There are no third party beneficiaries of this Warranty.  
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of  
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with  
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)  
days after such defect or noncompliance is discovered or should have been discovered, routed through  
the dealer and distributor from whom the purchase was made, transportation charges prepaid.  
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the  
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF  
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS  
WARRANTY.  
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF  
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND  
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/  
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising  
directly or indirectly from the product, whether such claim is based upon breach of contract, breach  
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality  
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or  
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for  
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.  
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to  
obtain materials or manufacture replacement parts.  
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,  
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized  
to alter, modify, or enlarge this Warranty.  
Answers to any questions regarding warranty service and locations may be obtained by contacting:  
F-8494 (Rev. 6/23/2005)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY  
All Models Except Mow’n MachineTM Zero-Turn Mowers  
Please Enter Information Below and Save for Future Reference.  
Date Purchased: ____________________________  
Model Number: ____________________________  
From (Dealer): __________________________________________  
Serial Number: __________________________________________  
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth  
below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE  
PRODUCT TO THE ORIGINAL PURCHASER.  
All current model loaders and backhoes are warranted for two (2) years from the date of delivery to the original purchaser.  
The warranty periods for specific parts or conditions are listed below:  
Part or  
Condition  
Warranted  
Duration (from date of  
delivery to the original  
purchaser)  
Model Number  
Gearbox  
Seals  
All units listed below  
2 years  
BW1260, BW1620, BW1800, BW2400  
8 years  
7 years  
BW240HD, BW180HD, BW180HB, BW126HB  
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X, BB8400X,  
DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240  
6 years  
Gearbox  
components PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2, RM660-2,  
RD990X, PRD6000, PRD7200, PRD8400, S15CD, S20CD, S22CD, S25CD, S27CD, BW180LH, 5 years  
TC/R74, TC/R68, TC/R60, TBW144, TBW180, TBW204  
3 years (1 year if used in rental or  
commercial applications)  
RDC54, RD60, RD72, TBW150C, TS/R60, TS/R52, TS/R44  
Blade  
spindles  
RM550-2, RM660-2, RD990X, PRD6000, PRD7200, PRD8400, TBW144, TBW180, TBW204  
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW126HB, BW180-3, BW180HB,  
3 years  
Rust-through BW180HD, BW1260, BW1800, BW240, BW240HD, 2162, 3240, DS1260, DSO1260, DS1440, 10 years  
TS1680  
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to  
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materially  
modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center.  
This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made with parts other  
than those obtainable through WOODS.  
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to a  
third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.  
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by  
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.  
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS, in  
its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of  
purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the  
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or  
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY.  
THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.  
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS  
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY  
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the  
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal  
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues  
or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery or  
rental; or (v) any other type of damage to property or economic loss.  
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture  
replacement parts.  
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS, its  
authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this  
Warranty.  
Answers  
to  
any  
questions  
regarding  
warranty  
service and locations may be obtained by contacting:  
Woods Equipment  
Company  
2606 South Illinois Route 2  
Post Office Box 1000  
Oregon, Illinois 61061 USA  
800-319-6637 tel  
800-399-6637 fax  
F-3079 (Rev. 2/14/2011)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PART NUMBER  
MAN0426  
815-732-2141 tel  
815-732-7580 fax  
©2006 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods  
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual  
are the property of their respective companies or mark holders. Specifications subject to change without notice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Weslo Treadmill WETL268051 User Manual
Weslo Treadmill WLTL29013 User Manual
Westinghouse Door AK 2A 25 User Manual
Whirlpool Microwave Oven GT1195SH User Manual
Whirlpool Microwave Oven YKHMS145J User Manual
Whirlpool Ventilation Hood RHH 4300 User Manual
Whirlpool Washer CAWC529PQ0 User Manual
Whistler Radar Detector XTR 185 User Manual
Wolf Griddle WEG24R User Manual
Yamaha Computer Drive CRW3200SX User Manual