FLOOR SWEEPER
Operating Instructions
MODEL:
TRACER FS
QTFSD (Diesel Version)
QTFSG (Gas Version)
Read these instructions before using the machine
M
98349 11/01/03
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Machine Data Log..........................................2
Table of Contents...........................................3
GROUP PARTS LIST
Frame Group................................................5-1
Differential Group.........................................5-3
Front Wheel Drive Group.............................5-5
Impeller Group. ............................................5-7
Impeller (Wet Sweep Bypass).....................5-9
Rear Clip Group...........................................5-11
Console Group.............................................5-13
Brake Group.................................................5-15
Steering Group.............................................5-17
Rear Suspension Group..............................5-19
Engine Group (GAS)....................................5-21
Engine Group (DIESEL-1)...........................5-23
Engine Group (DIESEL-2)...........................5-25
Drive Group..................................................5-27
Side Broom Group.......................................5-29
Filter Group. .................................................5-31
Hydraulic Group...........................................5-33
Hopper Group ..............................................5-35
Main Broom Lift Group.................................5-37
Main Broom Group.......................................5-39
Instrument Panel Group (GAS)...................5-41
Instrument Panel Group (DIESEL)..............5-43
Wiring Group (GAS).....................................5-45
Wiring Group (DIESEL). ..............................5-47
Horn Wire Asm.............................................5-49
Wiring Schematic (GAS)..............................5-51
Wiring Schematic (DIESEL) ........................5-52
Engine Service Parts (GAS)........................5-53
Engine Service Parts (DIESEL)...................5-54
HD Air Cleaner.............................................5-55
Notes............................................................5-57
Warranty ......................................................5-58
HOW TO USE THIS MANUAL
How to use this Manual..................................1-1
SAFETY
Important Safety Instructions.........................2-1
Hazard Intensity Level. ..................................2-2
Safety Label Location.....................................2-3
OPERATIONS
Technical Specifications................................3-1
Controls..........................................................3-2
Machine Operation.........................................3-7
Pre-Run Machine Inspection ......................3-7
Starting Machine.........................................3-7
Sweeping.....................................................3-7
Operating on Grades ..................................3-7
Stopping Machine .......................................3-8
Storing Machine..........................................3-8
Dumping the Hopper...................................3-8
Hopper Safety Arm.....................................3-8
Machine Jacking............................................3-9
Machine Tie-Downs .......................................3-9
MAINTENANCE
Hydraulics......................................................4-1
Directional Control System............................4-2
Throttle Neutral Position.................................4-2
Main Broom....................................................4-3
Side Broom ....................................................4-5
Belts...............................................................4-6
Differential Drive.............................................4-9
Skirts..............................................................4-9
Hopper..........................................................4-11
Brakes/Tires.................................................4-13
Battery Information.......................................4-14
Hydraulic Schematic....................................4-15
Hydraulic Troubleshooting...........................4-15
Propelling Troubleshooting..........................4-16
Machine Troubleshooting.............................4-17
Service Schedule.........................................4-18
3
QTFSG/QTFSD 98349 05/15/03
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THIS MANUAL
The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition. They are
listed in this general order:
This manual contains the following sections:
-
-
-
-
HOW TO USE THIS MANUAL
SAFETY
OPERATIONS
-
-
-
-
-
-
-
-
-
-
Hydraulics
MAINTENANCE
Directional Control System
Throttle Neutral Position
Main Broom
Side Broom
Belts
Differential Drive
Skirts
Hopper
-
PARTS LIST
The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.
Parts may be ordered from authorized Windsor
dealers. When placing an order for parts, the
machine model and machine serial number are
important. Refer to the MACHINE DATA box which
is filled out during the installation of your machine.
The MACHINE DATA box is located on the inside of
the front cover of this manual.
Brakes/Tires
-
Battery Information
Hydraulic Schematic
Hydraulic Troubleshooting
Propelling Troubleshooting
Machine Troubleshooting
Service Schedule
-
-
-
-
-
MODEL _____________________________________
DATE OF PURCHASE ________________________
SERIAL NUMBER ____________________________
SALES REPRESENTATIVE # ___________________
DEALER NAME ______________________________
OPERATIONS GUIDE NUMBER __________________
The PARTS LIST section contains assembled parts
illustrations and corresponding parts list. The parts
lists include a number of columns of information:
-
-
-
-
-
REF – column refers to the reference
number on the parts illustration.
PART NO. – column lists the part
number for the part.
QTY – column lists the quantity of the
part used in that area of the machine.
DESCRIPTION – column is a brief
description of the part.
SERIAL NO. FROM – column indicates
the first machine the part number is
applicable to. When the machine design
has changed, this column will indicate
serial number of applicable machine.
The main illustration shows the most
current design of the machine. The
boxed illustrations show older designs. If
column has an asterisk (*), call
PUBLISHED ________________________________
Copyright 1995 Windsor Industries, Printed in USA
The model and serial number of your machine is on
the bottom back-end of the machine.
The SAFETY section contains important information
regarding hazard or unsafe practices of the
machine. Levels of hazards is identified that could
result in product or personal injury, or severe injury
resulting in death.
The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.
manufacturer for serial number.
NOTES – column for information not
noted by the other columns.
-
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.
NOTE: The 98# on the lower left corner of the front
cover is the part number for this manual.
QTFSG/QTFSD 98349 05/15/03
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
When using a gas or diesel powered appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
! WARNING:
To reduce the risk of fire, electric shock, or injury:
This machine is for dry use only and shall not be used or stored outdoors in wet conditions.
Use only as described in this manual. Use only manufacturer’s recommended brushes and attachments.
If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return
it to an authorized service center.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near
flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops
and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
During operation, attention shall be paid to other persons, especially children.
When leaving unattended, secure against unintentional movement.
The machine shall only be operated by instructed and authorized persons.
When leaving unattended, switch off or lock the main power switch to prevent unauthorized use.
The exhaust system gets very hot, keep hands, clothing and any items than can burn away from the engine
while hot.
This machine emits lethal exhaust gas. Ensure the working area is well ventilated.
Keep hands, feet, strings and ties away from all moving parts while the machine is in operation.
Keep hair, loose clothing, fingers and all parts of the body away from openings.
Disconnect battery before cleaning or servicing machine.
This machine not suitable for picking up hazardous dust.
Before use, all covers and doors shall be put in the positions specified in the instructions.
SAVE THESE INSTRUCTIONS
QTFSG/QTFSD 98349 05/15/03
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
HAZARD INTENSITY LEVEL
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR
SAFETY . The level of hazard intensity is determined by the following definitions:
! WARNING
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
! CAUTION
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property
damage.
FOR SAFETY: To identify actions which must be followed for safe operation or equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating
condition. Following is information that signals some potentially dangerous conditions to the operator or the
equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on
the machine. Please take the necessary steps to train the machine operating personnel.
FOR SAFETY
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the
machine. Use Windsor approved replacement parts.
! WARNING
Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep
sparks and flames away from the battery. Do not smoke around battery.
! WARNING
Hazardous voltage. Shock can result. Disconnect battery before working on machine. Only qualified
personnel should work inside machine. Always wear eye protection and protective clothing when working
on or near battery. Avoid skin contact with the acid contained in the battery.
! WARNING
Never allow metal to lie across battery tops.
! WARNING
Flammable materials or reactive metals can cause explosion or fire. Do not sweep these materials.
! WARNING
Engine emits toxic gases. Severe respiratory damage or asphyxiation can results. Provide adequate
ventilation. Consult with your regulatory agency for exposure limits. Keep engine properly tuned.
! WARNING
Machine can emit excessive noise. Consult with your regulatory agency for exposure limits. Hearing
loss can result. Wear hearing protection.
! WARNING
Lift arm pinch points. Keep clear of hopper lift arm. Raised hopper may fall. Engage hopper safety arm.
! WARNING
Moving belts. Keep away.
QTFSG/QTFSD 98349 05/15/03
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY LABEL LOCATION
NOTE: These drawings indicate the location of safety labels on the Tracer FS. If, at any time, the labels become
illegible contact your Windsor representative for prompt replacement.
QTFSG/QTFSD 98349 05/15/03
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY LABEL LOCATION
NOTE: These drawings indicate the location of safety labels on the Tracer FS. If, at any time, the labels become
illegible contact your Windsor representative for prompt replacement.
QTFSG/QTFSD 98349 05/15/03
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
ITEM
Power Source: Gas
DIMENSION/CAPACITY
20hp, 2 Cylinder, Liquid-Cooled
14hp, 2 Cylinder, Liquid-Cooled
Floating I-Beam
10k/hour
Diesel
Suspension
Maximum Speed
Sweep Path
1200mm
Main Broom
812mm
Main Broom Diameter
355mm
Side Broom
510mm
Hopper Capacity
Hopper Dump
Dust Control
180 liters
1520mm
54ft2 (5m2) pleated filter with exclusive
cyclonic pre-filter
Dual mechanical disc with parking brake
Rear wheel, rack & pinion
405mm dia. Pneumatic
1505mm
Brakes
Steering
Tires
Dimensions: Height
Weight
1060 lbs.
Length
2006mm
Coverage
12,000m2/hr
QTFSG/QTFSD 98349 05/15/03
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
SPECIAL NOTES:
The sound pressure level at the operator’s ear was
measured to be 78 dBA for the QTFSG and 83 dBA for
the QTFSD. This was a nearfield, broad-band
measurement made during normal operation on a
composite tile floor with a white pad. This appliance
contains no possible source of impact noise. The
instantaneous sound pressure level is below 63 Pa.
The weighted root mean square acceleration at the
operator’s arms was measured to be below 2.5m/s2 for
the QTFSG and below 3.2m/s2 for the QTFSD. The
weighted root mean square acceleration at the
operator’s posterior was measured to be below 0.5m/s2
for the QTFSG and below 1.3m/s2 for the QTFSD. This
was a tri-axial, third-octave-band measurement made
during normal operation on a composite tile floor. The
measurement and related calculations were made in
accordance with ANSI S3.34-1986.
QTFSG/QTFSD 98349 05/15/03
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
L. Engine Temperature Light
M. Oil Pressure Light
N. Engine Glow Plug Light (Diesel
Only)
O. Light Switch
P. Engine Throttle Handle
Q. Choke Cable
R. Key Switch
S. Circuit Breakers
T. Horn Pad
U. Steering Wheel
V. Wet Sweep Bypass
A. Directional Control Pedal
B. Brake Pedal
C. Parking Brake
D. Operator Seat
E. Rear Cover Latch
F. Main Broom Lever
G. Side Broom Lever
H. Filter Shaker Switch
I. Hopper Door Switch
J. Hopper Lift Switch
K. Hopper Safety Arm
QTFSG/QTFSD 98349 05/15/03
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
A - DIRECTIONAL CONTROL PEDAL
This pedal controls the direction of travel and the
speed of the machine.
E – REAR COVER LATCH
The rear cover latch locks the rear cover in the
closed position. To open the rear cover, push the
latch in and pull the rear cover back. To close the
rear cover, lower it slowly until the latch engages the
floor slot. Do not let the rear cover drop, or damage
to the latch or cover may occur.
FOR SAFETY: When the rear cover is open a
safety switch prevents the operation of the main
broom and vacuum impeller.
Slowly pressing the front of the pedal causes the
machine to travel forward. Pressing the rear of the
pedal causes the vehicle to travel in reverse. The
machine speed can be controlled by varying the
pressure on the front or rear of the pedal.
F – MAIN BROOM LEVER
FOR SAFETY: The main broom and the vacuum
impeller automatically begin to operate when the
main broom lever is positioned in the forward end of
its slot.
FOR SAFETY: The machine can coast for a short
distance after releasing the directional pedal. Use
the brake pedal to slow or stop the machine.
The main broom lever controls the position and the
drive of the main broom. To start the main broom
and lower it to the floor, release the main broom
lever and let it drop to the front end of its slot. To
shut off and raise the main broom, pull the main
broom lever back into its locked position.
B – BRAKE PEDAL
This brake operates the disc brakes on the two front
tires. To slow or stop the machine, apply pressure
to the brake pedal.
G – SIDE BROOM LEVER
C – PARKING BRAKE LEVER
The knob located above the brake pedal is the
parking brake knob. To set the parking brake, slide
the parking brake knob up to the top of its slot, then
depress the brake pedal. To release the parking
brake, slide the parking brake knob to the bottom of
its slot. The brake pedal will return to its raised
position.
FOR SAFETY: The side broom automatically
begins to operate when the side broom lever is
positioned in the forward end of its slot.
The side broom lever controls the position and the
drive of the side broom. To start the side broom and
lower it to the floor, release the side broom lever and
let it drop to the front end of its slot. To shut off and
raise the side broom, pull the side broom lever back
into its locked position.
FOR SAFETY: Always park on a level surface, turn
the machine off, and set the parking brake before
leaving the machine, and before servicing the
machine.
When parking the machine, always raise the brooms
to prevent the bristles from taking a set.
D – OPERATOR SEAT
H – FILTER SHAKER SWITCH
The operators seat position is adjustable. To
change positions loosen the four lower mounting
bolts and slide the seat to the desired position.
Tighten the four mounting bolts.
The filter shaker switch operates the dust filter
cleaning system.
For efficient sweeping the filter must be cleaned on
a regular basis. To clean the filters, pull the Wet
Sweep Bypass knob, then push and hold the filter
shaker switch for 10-20 seconds. Clean the filters
just before dumping the hopper. In very dusty
conditions the filter may need to be cleaned more
frequently.
QTFSG/QTFSD 98349 05/15/03
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
I – HOPPER DOOR SWITCH
L – ENGINE TEMPERATURE LIGHT
The hopper door switch opens and closes the
hopper dump door. Pushing the front half of the
hopper door switch closes the hopper dump door.
Pushing the rear half of the switch opens the hopper
dump door. A beeper sounds when the door is in
the closed position. Sweeping should not be
attempted when the hopper door is closed.
The engine temperature light indicates when the
engine is overheating. If the light comes on, stop
the engine immediately and determine the cause.
Failure to stop the engine will result in engine
damage. Some causes of engine overheating are a
clogged radiator, clogged cooling fins in the radiator,
loose fan belt or other engine malfunction. Consult
your Engine Owners guide to help determine the
problem.
J – HOPPER LIFT SWITCH
The hopper lift switch is used to raise and lower the
hopper during dumping operations. To raise the
hopper, press and hold the front half of the hopper
lift switch until the hopper has raised to the desired
height. Then release the switch. To lower the
hopper, press and hold the rear half of the hopper lift
switch until the hopper lowers to the normal
sweeping position.
M – OIL PRESSURE LIGHT
The engine oil pressure light indicates inadequate
engine oil pressure. If the light comes on, stop the
engine immediately and determine the cause.
Failure to stop the engine will result in engine
damage.
N – ENGINE GLOW PLUG LIGHT
(DIESEL ONLY)
FOR SAFETY: The hopper lift switch will not raise
or lower the hopper if the key switch is in the off
position.
The glow plug light is a time-controlled light that
allows the glow plugs to heat up sufficiently before
cranking the engine. When the ignition switch is
turned clockwise to the “RUN” position, the light will
come on. After 5-30 seconds, depending on
temperature, the light will go off. Then the engine
can be cranked with the ignition switch.
K – HOPPER SAFETY ARM
The hopper safety arm is used to support the hopper
in the raised position. The safety arm should be
used whenever inspection or service is performed
under the hopper. Do not rely on the hydraulic
cylinder to keep the hopper raised.
O – LIGHT SWITCH
The light switch operates the headlights and
taillights.
Raised hopper may fall. Engage hopper safety
arm before working under hopper.
P – THROTTLE
The throttle is an adjustable, lockable tee-handle.
The handle is unlocked by turning counter-
clockwise, and locked by turning clockwise. Start
the engine with the throttle pushed all the way in.
When the engine has adequately warmed up, unlock
and pull the throttle all the way out and lock. This
will set the engine at the maximum governed speed.
The throttle may be adjusted and locked anywhere
between idle and max. if desired. Consult engine
service guide.
QTFSG/QTFSD 98349 05/15/03
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
DIESEL:
DEVICE RATING
Q – CHOKE (GAS ONLY)
COMPONENT
PROTECTED
Glow Plugs
By pulling this knob out, the choke is engaged for
cold starting. To release choke, push the knob in.
CB-1
CB-2
30A
30A
Starter Relay, Oil
Pressure Lamp,
Water Temp. Lamp,
Glow Plug Lamp,
Optional Charge
Light, Optional Air
Registration Light
Side Broom Valve,
Head Lamps, Tail
Lamps, Horn,
R – KEY SWITCH
The key switch controls starting and electrical power
for most machine functions. To start the machine,
turn the key clockwise past the “RUN” position to the
crank position. After engine has started release key.
(For starting diesel engines, see “Glow Plug Light”).
To stop engine, turn key counter-clockwise.
CB-3
15A
CB-4
CB-5
15A
15A
Options
S – CIRCUIT BREAKERS
Hopper Dump Door,
Shaker Motor, Hour
Meter, Hopper
The circuit breakers are circuit protection devices
designed to interrupt the flow of current in the event
of an electrical overload. When tripped, the circuit
breakers must be reset by pressing the exposed
button on the face of the affected circuit breaker. If
the circuit breaker continues to trip, the cause of the
electrical overload should be found and corrected.
Raise/Lower Valves
T – HORN PAD
The horn pad is located on the steering wheel. The
horn is activated by pressing on any area of the horn
pad.
The following chart shows the circuit breakers and
the components they protect.
U – STEERING WHEEL
GAS:
DEVICE RATING
COMPONENT
PROTECTED
The steering wheel controls the two rear wheels.
The machine is highly receptive to the movement of
the wheel. Operators should use care until they
become experienced in driving the machine.
CB-1
CB-2
30A
15A
Voltage Regulator
Igniter, Fuel Pump,
Oil Pressure Lamp,
Water Temp. Lamp
Side Broom Valve,
Head Lamps, Tail
Lamps, Horn
V – WET SWEEP BYPASS
CB-3
15A
By pulling this knob out, vacuum is cut off from filter
and hopper. To prevent damage to filter caused by
moisture, pull knob out when sweeping through
puddles. To maximize filter cleaning, pull knob out
before pressing filter shaker switch.
CB-4
CB-5
15A
15A
Options
Hopper Dump Door,
Shaker Motor, Hour
Meter, Hopper
Raise/Lower Valves
QTFSG/QTFSD 98349 05/15/03
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
BEFORE OPERATING THE FS:
TO SWEEP
1. Complete the machine data sheet on page 2.
Plan the sweeping pattern in advance. For efficient
operation, the sweeping runs should be long with as
little stopping and starting as possible. Overlap the
brush paths and complete an entire section at one
time.
2. Read this manual carefully before operating or
servicing the machine.
Do not operate machine unless Operation
manual is read and understood.
Use the side broom to pull debris from areas near
walls or obstructions. The side broom is also useful
for extending the sweeping paths on long runs. If
the area to be swept is very dusty, the side broom
should be raised to prevent dust clouds.
3. Carefully read the Owner’s Manual that is
supplied for your gas or diesel machine.
REFERENCE FOR GAS ENGINE:
Kawasaki FD620D – Owners Manual
REFERENCE FOR DIESEL ENGINE:
Lombardini LDW series – Use, Maintenance
Oversized debris that can inhibit sweeping
operations should be picked up by hand. This
includes large cartons and items that could become
tangled in the brooms, such as wire or banding
material.
4. Check oil and engine fuel in the machine. See
engine Owner’s manual for complete filling
instructions.
The machine is very responsive. Avoid turning the
steering wheel too sharply when the machine is in
motion. Avoid sudden turns except in an
emergency.
5. Check the hydraulic fluid level in the hydraulic
power unit. See hydraulics in the maintenance
section.
1. Put the main broom lever in the forward position
6. Check the main and side broom for correct
adjustment. See brooms in the maintenance
section.
to lower the main broom.
2. Put the side broom lever in the forward position
to lower the side broom.
STARTING THE MACHINE
NOTE: The main broom and side broom lever
indicators are color-coded green.
FOR SAFETY: use caution when backing machine.
Do not carry riders on the machine. Always follow
basic safety and traffic rules. Go slow on slippery
surfaces and grades.
3. Make sure that the hopper door is open. A
beeper will sound if the hopper door is not
open.
1. The operator should be sitting on the seat with
a foot on the brake pedal or with the parking
brake on. The directional pedal should be in
neutral.
4. Sweep as required.
OPERATING ON GRADES
FOR SAFETY: Before starting machine, make sure
that all safety devices are in place and operating
properly.
Operate the machine slowly on grades. Use the
brake pedal to control the machine speed.
NOTE: When operating machine, go slowly on
grades and slippery surfaces.
2. Turn the key switch clockwise to the “ON”
position.
3. Drive the machine to the area where sweeping
is to begin.
QTFSG/QTFSD 98349 05/15/03
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
STOPPING THE MACHINE
TO ENGAGE THE HOPPER SAFETY ARM
1. Remove foot from the directional pedal and
apply the brake.
Raised hopper may fail. Engage hopper safety
arm before working under hopper.
2. Raise and turn off the brooms by pulling the
main and side broom levers back to the rear
locked position.
1. Set the machine parking brake.
FOR SAFETY: Before leaving or servicing machine;
stop on level surface, set parking brake, turn OFF
machine and remove key.
3. Set the parking brake.
4. Turn the key switch counterclockwise to the off
position. Remove the key.
2. Raise the hopper.
STORING THE MACHINE
3. Unhook the safety arm and swing it down into
position over the safety arm retainer. Do not let
the safety arm drop into position.
When storing the machine for extended periods of
time, the following procedure must be followed to
lessen the chance of rust, sludge, or other
undesirable deposits from forming.
4. Slowly lower the hopper until the safety arm is
secure.
1. Empty the hopper.
2. Raise the main broom and the side broom.
3. Park the machine in a cool, dry area.
4. Remove or change the batteries for 4 hours,
once every three months.
DUMPING THE HOPPER
NOTE: The hopper dump switches are numbered
and color-coded. The filter shaker is shown in
yellow and hopper functions are shown in red.
1. Drive the machine to the dump site or dumpster.
2. The correct sequence for dumping the hopper is
shown by following the numbers on the switch
panel.
1. Clean the filter by pressing the filter shaker
switch for 10-20 seconds.
2. Close the hopper door by pushing and
releasing the front half of the hopper door
switch. The beeper will sound.
Make sure that the lower end of the safety arm is
correctly held in the retainer on the machine
frame.
3. Press and hold the front half of the hopper
lift switch and raise the hopper to a height
that will clear the dumpster, then release the
switch. Drive forward slowly until the hopper
is positioned above the dumpster.
4. Dump the hopper by pressing and then
releasing the rear half of the hopper door
switch. After dumping, back the machine
slowly away from the dumpster.
5. Lower the hopper by pressing and holding
the rear half of the hopper lift switch.
QTFSG/QTFSD 98349 05/15/03
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
TO DISENGAGE THE HOPPER SAFETY ARM
TO JACK UP MACHINE
1. Raise the hopper.
1. Empty and lower the hopper.
2. Place the safety arm in its storage position on
the inside of the hopper lift arm.
3. Lower the hopper.
2. Turn the key switch off and set the parking
brake.
FOR SAFETY: Before leaving or servicing machine;
stop on level surface, set parking brake, turn off
machine and remove key.
3. Block the tires that are not being raised to
prevent the machine from rolling.
FOR SAFETY: When servicing machine, block
machine tires before raising machine.
4. Use a jack of adequate capacity, raise the
machine using the designated jack locations.
TOWING OR PUSHING MACHINE
FOR SAFETY: When servicing machine, use hoist
or jack of adequate capacity, jack machine at
designated jack locations only. Block machine with
jack stands when raised.
Gas and diesel powered machines may be pushed
or towed easily by bypassing the transmission. To
do this raise the rear cover and remove the belt
guard. Locate the transmission. On the rear of the
transmission is a plunger valve. Push the valve in
as far as possible and pivot up the tow bar valve just
next to the valve. This bar is supplied to lock the
valve in the “IN” position. The machine can now be
easily pushed or towed up to 4 mph (7
5. When the machine is raised, use jack at the
designated jack locations.
FOR SAFETY: Block machine at designated jack
locations with jack stands when raised.
kilometers/hr).
6. Slowly lower the machine onto the jack stands.
7. Be sure that the machine is secure.
8. Service or inspect the machine as required.
9. When finished working on the machine, raise the
machine off the jack stands.
Do not exceed 4 mph (7 kilometers/hr) as
damage to the transmission may result.
10. Remove the jack stands.
When towing is complete, slide tow valve bar out of
the way to release valve.
11. Lower the machine to the floor. Remove the
blocks from the tires.
MACHINE JACKING
MACHINE TIE-DOWNS
The machine may be jacked up for service or
inspection by using the specified jack locations.
Always block the tires when jacking up the machine.
There is a tie-down location at each corner of the
machine. The front attach points are the frame
cutouts located directly above each front tire. The
rear attach points are the right and left lower flange
of the frame channels, where they join the rear
bumper. An alternate single rear attach point is
around the pivot of the rear axle beam, located at
the center of the machine behind the rear jack point.
The right front jack location is the base of the side
broom, just ahead of the right tire.
The left front jack location is the lower front frame
channel just ahead of the left front tire.
The rear jack location is the steel beam mount
located at the rear of the machine, centered under
the plastic bumper.
NOTE: When transporting the machine on a trailer
or in a truck, in addition to tie-downs, be sure to set
the machine parking brake, and block the tires to
prevent the machine from rolling.
QTFSG/QTFSD 98349 05/15/03
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
HYDRAULIC FLUID
5. Remove bolts (4) in feet of reservoir.
6. Shift reservoir forward so that short leg of
reservoir drops down and rests on lower frame.
7. Remove upper hydraulic hose from reservoir.
8. Lift reservoir out of frame and rest on outer
frame with open port above oil level.
9. Tilt reservoir back and remove last hose.
10. Reservoir may be emptied by pouring fluid out of
ports.
Hydraulic fluid is used with the hydraulic pump to
operate the hopper lift system and the side broom
motor. The condition of the hydraulic fluid plays a
large part in determining the life of the hydraulic
system.
The hydraulic fluid used in the Tracer Gas/Diesel
powered Floor Sweeper is Chevron 400 15W40. If a
different hydraulic fluid is used, it must closely match
the viscosity specification below.
11. The fluid strainer may be removed for inspection
and to speed fluid drainage.
NOTE: Do not overfill the reservoir. Expansion of
the hydraulic fluid when heated to the normal
operating temperature can cause fluid to spill from
the reservoir, or cause damage to the component.
SUS @ 100” (38º C) 404-445
SUS @ 210” (38º C) 78-84
This specification has a flat viscosity curve (high
viscosity index). This means the thickness of the oil
stays relatively constant over a wide temperature
range. DO NOT use Automatic Transmission Fluid.
If the reservoir is overfilled, use a suction type
device to draw the excess hydraulic fluid from the
reservoir.
NOTE: The hydraulic components in the machine
rely on system hydraulic fluid for lubrication. Dirty or
contaminated fluid accelerates wear and
HYDRAULIC FLUID LEAKS
Pressurized hydraulic fluid spraying from a very
small hole can be very hard to see. Do not use
hands to locate the leak. Use a piece of cardboard
as shown below to find leaks.
malfunctions, and reduced component life.
HYDRAULIC FLUID RESERVOIR
The hydraulic fluid reservoir is located below the
broom levers inside the machine. To check the fluid
level remove the fill cap to read the dipstick attached
to the cap.
When servicing machine, use a sheet of
cardboard to locate leaking hydraulic fluid under
pressure. Keep eyes and hands clear of leaks.
Escaping hydraulic fluid under pressure can
cause severe injury.
NOTE: Do not overfill reservoir. Expansion of the
hydraulic fluid when heated to the normal operating
temperature can cause fluid to spill from the
reservoir, or cause damage to the component.
The oil in the reservoir should be replaced every 500
hours of use. To drain hydraulic reservoir:
1. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing the
machine, stop on level surface, apply parking brake,
turn off machine and remove key.
A – Hydraulic Line
B – Cardboard
C – Pinhole Leak
2. Raise rear cover.
3. Disconnect batteries from machine.
4. Remove impeller.
A – Hydraulic Pump
QTFSG/QTFSD 98349 05/15/03
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
HYDRAULIC FILTER
7. Loosen the locking nuts on both ends of the
threaded portion of the linkage rod.
8. Turning the balljoint changes the length of the
linkage rod, be sure that there is a minimum of
5/16” of threaded rod engaged in each of the
balljoints.
The hydraulic filter keeps the machines hydraulic
system clean to a level of 10 microns. The hydraulic
fluid filter is located just inside the left rear frame.
The filter should be changed every 500 hours.
TO REPLACE FILTER ELEMENT:
1. Stop the engine and set the parking brake.
2. Open the seat support.
3. Unthread and discard the hydraulic fluid filter
element.
4. Apply a thin coat of hydraulic fluid to the seal of
the new hydraulic fluid filter element.
5. Thread and hand tighten the new hydraulic fluid
filter element on the filter head.
9. When the new length is established, reconnect
the upper balljoint to the forward/reverse arm.
10. Tighten the two locking nuts on the threaded
portion of the linkage rod.
11. Reposition the directional foot pedal stop bolt.
12. The stop bolt must be adjusted so that the
directional foot pedal comes in contact with the
stop while there is still a small amount of travel
remaining in the throttle arm. This is done to
prevent heavy foot pressure from damaging the
throttle unit.
6. Close the seat support.
7. Operate the machine and check for leaks.
Correct any leaks found.
8. Check the hydraulic fluid reservoir level and fill
as required.
DIRECTIONAL CONTROL SYSTEM
(Refer to the Electrical Control Group in the
Parts section)
The directional control system controls the direction
and speed of the machine. The system is made up
of the directional pedal, the throttle box, the
transistorized controller and contactors. The
controller, located in the electrical drive
compartment, is sealed and can only be serviced by
trained service personnel.
THROTTLE “NEUTRAL POSITION”
ADJUSTMENT (Refer to the Console Group in
the Parts section)
Do not use a pressure washer to clean the inside
of the electrical drive compartment.
The throttle is automatically returned to its neutral
position by a spring centering system. If the
machine tends to creep forward or reverse when the
operators foot is removed from the directional foot
pedal, the throttle “neutral position” may require
adjustment as described below:
When servicing machine, disconnect battery
connections before working on machine.
DIRECTIONAL CONTROL PEDAL ADJUSTMENT
(Refer to the Console Group in the Parts section)
The directional control pedal is designed to prevent
driver fatigue. However if a different pedal angle is
preferred, these directions should be followed.
1. Turn off machine and set parking brake.
2. Raise the rear cover.
3. Disconnect the batteries from the machine.
4. Remove the drive motor dust cover.
5. Locate the throttle and spring centering
assembly.
1. Raise rear cover.
2. Disconnect batteries from machine.
3. Locate and remove the directional control pedal
stop bolt.
4. Locate the linkage rod beneath the directional
control pedal.
5. Adjusting the length of the linkage rod controls
the pedal angle. Shortening the linkage rod
causes the pedal to have a flatter angle with the
floor. Lengthening the linkage rod causes the
pedal to have a steeper angle.
6. To change the length of the linkage rod,
disconnect the upper end of the linkage rod from
the forward/reverse arm.
6. Disconnect the linkage rod from the throttle arm.
7. With the throttle arm free, the throttle will return
to its neutral position using its internal centering
spring.
8. Position the linkage rod balljoint over the hole in
the throttle arm. The balljoint should slide into
the hole without repositioning the throttle arm.
9. If required, shorten or lengthen the linkage rod
until proper engagement occurs.
10. Reattach linkage rod to the throttle arm.
11. Install the drive motor dust cover.
12. Connect batteries.
13. Lower hopper.
QTFSG/QTFSD 98349 05/15/03
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
MAIN BROOM (Refer to the Main Broom Group
and Main Broom Lift Group in the Parts section)
TO INSTALL THE MAIN BROOM
1. Turn off machine and set parking brake.
FOR SAFETY: The main broom and the vacuum
impeller automatically begin to operate when the
main broom lever is positioned in the forward end of
its slot.
FOR SAFETY: Before leaving or servicing the
machine, stop on level surface, apply parking brake,
turn off machine and remove key.
The main broom spans the width of the machine,
and sweeps debris into the hopper. Inspect the
main broom daily for wear or damage. Remove any
obstructions found in the main broom chamber, main
broom drive hub or idler hub.
2. Raise rear cover.
3. Disconnect batteries from machine.
4. Lower the main broom lever.
5. Open right side broom door.
6. If replacing a worn broom, turn the main broom
adjustment knob so that the broom drive hub is
raised to a position that will allow a new broom
to easily slide onto the broom drive hub.
7. Slide the new brush into the broom chamber.
8. Hold the broom by the core and rotate the
broom counter-clockwise while pushing the
broom onto the drive hub. Make sure that the
broom is fully seated onto the drive hub before
attempting to install the idler arm.
9. Locate the idler arm. Align the tabs on the idler
hub with the slots on the main broom core.
Slide the idler into the main broom core, the
position the upper right end of the idler arm onto
the two locator pins.
The main broom should be replaced when the
remaining bristles measure 5/8 “ (16mm) or less in
length.
NOTE: All original equipment brooms are equipped
with “Perform Alert™”. This feature tells the
operator when it is time to replace the main broom.
“Perform Alert™” brooms have bright yellow tufts
located on each end of the broom. These tufts are
pre-trimmed to indicate the length of a worn out
broom. When the main body of the broom wears to
a length that matches the yellow tufts, the broom
should be replaced.
10. Replace and tighten the D-ring retainer.
11. Close the broom door.
12. Check the main broom floor pattern and adjust
as necessary.
Always check the main broom pattern when
installing a new broom.
TO REMOVE THE MAIN BROOM
1. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing the
machine, stop on a level surface, apply parking
brake, turn off the machine and remove key.
2. Raise rear cover.
3. Disconnect batteries from machine.
4. Lower the main broom lever.
5. Open the right side broom door.
6. Remove the idler arm D-ring retainer.
7. Remove the main broom idler arm.
8. Grasp the broom by the core and remove.
QTFSG/QTFSD 98349 05/15/03
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CHECKING AND ADJUSTING THE MAIN BROOM
PATTERN
1. Using chalk, or similar material, coat and area of
the floor that is flat and smooth. If a suitable
material is not available, run the broom for two
minutes during the following test.
2. With the main broom raised, position the
machine so that the main broom is directly over
the chalked area.
3. Apply the parking brake to prevent the machine
from moving.
4. Lower the main broom to the floor for 10-15
seconds.
5. Raise the main broom, release the parking
brake, and back the machine away from the test
area.
A – Main Broom Adjustment Knob
6. Observe the pattern that the main broom left on
the floor. The pattern should be 1 to 1-1/2
inches (25.4 to 38.1mm) wide. The pattern
should not be tapered (wider at one end than the
other).
7. To adjust the width of the pattern, locate the
main broom adjustment knob, and loosen the
locking wing nut.
The adjustable bearing block used to correct a
tapered broom pattern is located just inside the right
broom door. Only the right side of the broom can be
raised or lowered to correct the pattern. Before
attempting the following adjustment, determine if the
right side of the broom needs to be raised or
lowered to correct the tapered pattern.
8. If the pattern is too wide, rotate the adjustment
knob clockwise to raise the broom. If the pattern
is too thin, rotate the adjustment knob,
counterclockwise to lower the broom. Tighten
the locking wing nut.
1. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing the
machine, stop on level surface, apply parking brake,
turn off machine and remove key.
9. Check the broom pattern again. Repeat the
procedure until the pattern is correct.
2. Raise rear cover.
3. Disconnect batteries from machine.
4. Open the right side broom door.
5. Remove the main broom.
6. Locate the plastic main broom bearing block just
inside the right broom door. Loosen the bearing
block retainer bolts.
7. Slide the bearing block up or down to correct the
tapered pattern condition.
A – Main Broom Pattern
B – 1 to 1-1/2” (25.4 to 38.1mm)
8. Tighten the bearing block retaining bolts.
9. Replace the main broom, and repeat the pattern
test procedure. Readjust if necessary to
eliminate the tapered pattern condition.
NOTE: If one end of the main broom pattern is more
than 1/2” (12.7mm) wider than the other end,
perform the following leveling procedure.
QTFSG/QTFSD 98349 05/15/03
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
5. Slide the side broom onto the side broom motor
shaft.
6. Install the side broom retaining pin and the
SIDE BROOM (Refer to the Side Broom Group in
the Parts section)
retaining pin locking clip.
FOR SAFETY: The side broom automatically
begins to operate when the side broom lever is
positioned in the forward end of its slot.
7. Adjust the side broom if necessary
The side broom should contact the floor in an area
as shown below. One third to one half of the side
broom bristles should contact the floor when the
broom is down.
The side broom is used to clean debris sway from
curbs and walls, and sweep it into the path of the
main broom. Inspect the side broom daily for wear
or damage. Remove any string, wire or banding
found wrapped around the side broom, side broom
hub, or shaft.
The side broom should be replaced when the
remaining bristles measure 2-1/2 inches (65 mm) or
less in length.
NOTE: All original equipment brooms are equipped
with “Perform Alert™”. This feature tells the
operator when it is time to replace the side broom.
“Perform Alert™” brooms have bright yellow tufts
located around the outside edge of the broom.
These tufts are pre-trimmed to indicate the length of
a worn out broom. When the main body of the
broom wears to a length that matches the yellow
tufts, the broom should be replaced.
ADJUSTING THE SIDE BROOM
TO REMOVE THE SIDE BROOM
1. Raise the hopper.
2. Engage safety arm.
1. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
Raised hopper may fall. Engage hopper safety
arm.
2. Raise rear cover.
3. Turn off machine and set parking brake.
3. Disconnect batteries from machine.
4. Raise the side broom lever.
5. Remove the locking clip from the side broom
retaining pin.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
6. Push up on the base of the side broom to relieve
the tension on the retaining pin, then remove the
retaining pin.
4. Raise rear cover.
5. Disconnect batteries from machine.
7. Slide the side broom off the side broom motor
shaft.
6. Lower the side broom lever.
7. Place a block or similar support under the side
broom to relieve the tension in the lift cable.
8. Locate the side broom adjustments links
located just above the side broom, and remove
the retaining pin passing through both
adjustment links.
TO INSTALL THE SIDE BROOM
1. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
9. Reposition the two adjustment links to move the
side broom up or down as required, and replace
the retaining pin.
2. Raise rear cover.
3. Disconnect batteries from machine.
4. Raise the side broom lever.
QTFSG/QTFSD 98349 05/15/03
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
TRANSMISSION JACKSHAFT BELT
ADJUSTING THE JACKSHAFT BELT
The transmission belt transfers power from the
engine to the transmission jackshaft on the gasoline
machines and from the engine jackshaft to the
transmission jackshaft on the diesel powered
machines.
Proper alignment is important for all belts on
Tracer machines. To properly align the
transmission jackshaft belt:
Repeat Steps 1-8 from above then:
9. Move the transmission jackshaft belt off its
pulley and loosen the setscrew in the pulley.
10. Using a straightedge between the pulleys to be
aligned, move the pulley left or right on it’s shaft
until proper alignment is established.
11. After this adjustment, check the transmission
belt alignment.
TO REPLACE BELT
1. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
12. Reverse steps 1-8.
13. If jackshaft belt idler pulley does not center on
belt, adjust by adding or removing washers
behind the idler pulley.
2. Raise rear cover.
3. Disconnect batteries from machine.
4. Remove the belt guard cover.
5. Remove the tension spring for the idler on the
transmission drive belt. Loosen tension on
impeller belt.
6. Loosen, but do not remove the four bolts in the
base of the shaft mounting bracket.
7. Slide mounting bracket toward engine to create
slack in the belt.
TRANSMISSION BELT
The transmission belt transfers power from the
transmission jackshaft to the transmission.
TO REPLACE BELT
8. Loosen, but do not remove 4 bolts in the bases
of the rear jackshaft mount and pump mount
bracket.
9. Loosen tensioning nut and bolt on the rear of
rear jackshaft mount. Slide rear jackshaft mount
away from engine.
1. Repeat steps 1-10.
11. Lift the jackshaft and bearings from the mount
and remove the transmission belt off the end of
shaft.
REAR JACKSHAFT (PUMP DRIVE) BELT
10. Remove the bolts retaining the bearings on
transmission jackshaft.
11. Lift the jackshaft and bearings from the mount
and remove the transmission drive belt, then the
transmission jackshaft belt.
The rear jackshaft belt transfers power from
transmission jackshaft to rear jackshaft.
TO REPLACE BELT
12. Remove the bolts retaining the bearing on the
rear jackshaft. Remove the belt controller rod.
13. Loosen bearing collars on rear jackshaft
bearings.
14. Remove first the main broom belt, then the
pump drive belt.
1. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
15. Slide the rear jackshaft outward to disengage
the pump coupling, then lift the shaft up to
remove drive belt in reverse order.
16. Reinstall belt in reverse order.
2. Raise rear cover.
3. Disconnect battery from machine.
4. Remove the belt guard cover.
5. Remove belt controller rod from rear jackshaft
mount and take main broom drive belt off double
pulley located on rear jackshaft.
6. Loosen, but don’t remove 4 bolts in base of rear
jackshaft mount and pump mount.
7. Loosen tensioning nut and bolt at rear jackshaft
mount, and slide mount away from engine.
8. Remove rear jackshaft belt.
QTFSG/QTFSD 98349 05/15/03
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
TO ALIGN BELT
VACUUM IMPELLER BELT (Refer to the Impeller
Group in the Parts section)
1. Repeat steps 1-7
8. Loosen tension on impeller drive pulley on end
of transmission jackshaft.
9. Slide pulley side to side on shaft to make proper
alignment.
The impeller belt transfers power from the auxiliary
motor to the impeller. Check the belt condition and
tension every 200 hours of operation.
10. Retighten setscrews in pulley.
11. Reverse Steps 1 –7.
The main broom and vacuum impeller
automatically begin to operate when the main
broom lever is positioned in the forward end of
its slot.
MAIN BROOM BELT (Refer to Main Broom Group
in the Parts section)
The main broom belt transfers power from the rear
jackshaft to the main broom pulley. Check the belt
condition and tension every 200 hours of operation.
REPLACING AND ADJUSTING THE VACUUM
IMPELLER BELT
1. Turn off machine and set parking brake.
The main broom and vacuum impeller
automatically begin to operate when the main
broom lever is positioned in the forward end of
its slot.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
2. Raise rear cover.
REPLACING AND ADJUSTING MAIN BROOM
BELT
3. Disconnect batteries from machine.
4. Remove the belt guard and the side filler panel.
5. Loosen the auxiliary motor base mounting bolts.
6. Slide the auxiliary motor back and remove the
jackshaft belt.
1. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
7. Pull the auxiliary motor forward to tension the
jackshaft belt. The belt has proper tension when
the belt deflects 1/4 inch (6 mm) from a force of
6 Ibs (3 kg) applied at the midpoint of the belt.
8. While keeping the motor and jackshaft pulleys
aligned, tighten the auxiliary motor base
mounting bolts.
2. Raise rear cover.
3. Disconnect batteries from machine.
4. Remove the belt guard.
5. Be sure main broom lift lever is in the raised
position. Remove the belt controlling rod from
rear jackshaft mount.
9. Replace the main broom belt.
10. Replace the side filler panel and the belt guard.
6. Remove belt from pulleys.
7. Install new belt and reinstall belt controlling rod.
TO ALIGN BELT
Repeat steps 1-7 under rear jackshaft (Pump Drive)
belt.
8. Loosen set screws in double pulley located on
the rear jackshaft.
9. Slide pulley side to side to align with main broom
drive pulley below.
10. Retighten setscrews in pulley.
11. Reverse Steps 1 –7.
NOTE: This adjustment may require realignment of
the rear jackshaft belt.
QTFSG/QTFSD 98349 05/15/03
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
IMPELLER BELT
6. Loosen 4 bolts holding transmission case to
mount.
The impeller belt transfers power from transmission
jackshaft to impeller.
7. Locate tensioning bolt at top of transmission
mount. Tighten or loosen bolt as needed to
properly tension chain.
8. Tighten 4 mounting bolts in transmission body.
1. Turn off machine and set parking brake.
If alignment of the chain and sprockets becomes
necessary, the alignment is accomplished by moving
the entire differential assembly side to side.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
TO REALIGN
2. Raise rear cover.
1. Raise the hopper and engage the hopper safety
3. Disconnect batteries from machine.
4. Remove the belt guard cover.
5. Release tension on impeller belt using tension
bolt under impeller arm.
6. Repeat Steps 5 and 6 under Rear Jackshaft
(Pump Drive) Belt.
arm.
Raised hopper may fall. Engage hopper safety
arm.
7. Remove rear jackshaft belt from front pulley.
8. Remove impeller belt.
2. Turn off machine and set parking brake.
9. Replace belt and reverse Steps 1 –6.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
TO ALIGN BELT
1. Loosen impeller belt, using the tensioning bolt
under the impeller arm.
2. Loosen set screws in the impeller pulley.
3. Slide the pulley side to side to make proper
alignment.
3. Remove rear cover.
4. Disconnect battery from machine.
5. Remove the drive motor dust cover.
6. Loosen all four locking on bearings supporting
the differential.
4. Tighten set screws in pulley.
5. Retighten impeller belt.
7. Loosen the set screws in the two brake disks.
8. Loosen but don't remove the hardware attaching
the bearing flanges to the frame.
DIFFERENTIAL DRIVE CHAIN (Refer to the
Differential Group in the Parts section)
9. Make sure there is little tension on the drive
chain. Gently slide the differential in it's bearing
to restore proper alignment.
The differential drive chain transfers power from the
output sprocket of transmission to differential
sprocket. Check the chain condition and tension
every 200 hours of operation.
NOTE: The brake disks must remain stationary
while the differential shafts move in them.
10. Reverse Steps 1-8. Follow tensioning
REPLACING AND ADJUSTING DIFFERENTIAL
DRIVE CHAIN
instructions above.
NOTE: After aligning the differential the small
sprockets at each end of the differential may need to
be realigned with the wheel sprockets. If so, loosen
setscrews in small sprockets and slide on differential
shaft until aligned. Retighten setscrews.
1. Raise the hopper and engage the hopper safety
arm.
2. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
3. Raise rear cover.
4. Disconnect batteries from machine.
5. Remove the drive motor dust cover.
QTFSG/QTFSD 98349 05/15/03
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
DRIVE WHEEL CHAIN (Refer to the Front Wheel
Group in the Parts section)
REPLACING THE RIGHT BROOM DOOR SKIRT
1. Turn off machine and set parking brake.
The drive wheel chain transfers power from the
differential shaft to the drive wheels. Check the
chain condition and tension every 200 hours of
operation.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
REPLACING AND ADJUSTING THE DRIVE
WHEEL CHAINS
2. Open the right broom door.
3. Loosen the lower three retaining bolts on the
side skirt mounting plate.
1. Turn off machine and set parking brake.
4. Slide the worn side skirt out of the skirt retainer.
5. Slide a new skirt into place. Tighten the three
retaining bolts.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
6. Adjust the side skirt.
ADJUSTING THE RIGHT BROOM DOOR SKIRT
2. Raise rear cover.
3. Disconnect batteries from machine.
4. Chock the rear wheels. Jack up and remove the
front tire.
5. Remove the chain guard and tensioner disk.
6. Check the drive wheel chain for excessive wear.
Replace if necessary.
1. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
7. Check the drive wheel and differential shaft
sprockets to proper alignment. If they are not
lined up, loosen the setscrews on the
differential shaft sprocket, align the sprockets,
and tighten the setscrews.
2. Open the right broom door.
3. Loosen the three upper adjustment bolts on the
side skirt mounting plate.
4. Adjust the side skirt for correct floor clearance,
then tighten the three adjustment bolts.
8. Replace the chain guard and tensioner disk.
9. Check the chain tension. There should be 1/2
inch (1 5 mm) slack measured midway between
the sprockets. To adjust the tension, loosen the
chain guard mounting bolt and rotate the disk.
Tighten the chain guard mounting bolt.
10. Replace the tire and slowly lower the machine
to the floor.
11. Repeat the procedure for the other drive tire.
SKIRTS AND SEALS (Refer to the Frame Group
and the Main Broom Group in the Parts section)
The main broom skirts prevent dust from exiting the
main broom chamber.
The skirts should be
inspected for wear or damage daily. When correctly
adjusted, they should clear the floor by 0 to 1/8 inch
(0 to 3mm).
NOTE: Original equipment skirts are provided with
“Perform Alert™” wear indicators.
The wear
indicator is raised horizontal line near the lower edge
of the skirts. When a skirt is worn to this line it
should be replaced. A skirt can be adjusted many
times before it wears to the “Perform Alert™” strip.
During daily inspections the “Perform Alert™”
indicators are useful in determining when skirts are
close to requiring replacement.
QTFSG/QTFSD 98349 05/15/03
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
REPLACING THE LEFT BROOM SKIRT
ADJUSTING THE REAR BROOM SKIRT
1. Turn off machine and set parking brake.
1. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
2. Raise rear cover and disconnect the batteries
from the machine.
2. Loosen the five upper adjustment nuts on the
rear skirt mounting plate.
3. Open the left broom door.
3. Adjust the rear skirt for correct floor clearance,
then tighten the adjustment nuts.
NOTE: The left skirt is mounted to the frame. This
skirt does not have a wear indicator strip.
RECIRCULATION SKIRT
4. Remove the five adjustment nuts and the
retaining bars.
5. Replace the worn side skirt with a new skirt.
6. Install the retaining bars and adjustment nuts.
7. Adjust the side skirt.
The recirculation skirt helps to channel debris that
has been carried over the main broom, back into the
sweeping area. The recirculation skirt should be
checked daily for wear or damage.
REPLACING THE RECIRCULATION SKIRT
ADJUSTING THE LEFT BROOM SKIRT
1. Turn off machine and set parking brake.
1. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
2. Raise the rear cover and disconnect the
batteries from the machine.
3. Remove the main broom.
2. Raise rear cover and disconnect the batteries
from the machine.
3. Open the left broom door.
4. Open the left broom door.
5. Remove the three retaining nuts and retaining
strip on the left side broom skirt.
6. Loosen the five retaining nuts on the
NOTE: The left skirt is mounted to the frame. This
skirt does not have a wear indicator strip.
recirculating skirt retaining plate.
4. Loosen the five adjustment nuts.
5. Adjust the side skirt for correct floor clearance,
then tighten the adjustment nuts.
6. Tighten the five broom skirt.
7. Adjust the rear skirt.
7. Slide the worn skirt out of the skirt retainer and
replace with a new skirt.
8. Hold the skirt firmly in place and tighten the five
retaining bolts. No adjustment is required.
QTFSG/QTFSD 98349 05/15/03
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
HOPPER SEALS
The hopper seals prevent dust from exiting around
the hopper where it meets the broom chamber.
There are two side hopper seals and one upper
hopper seal. These seals should be inspected for
wear or damage daily. When correctly adjusted, the
two hopper side seals should clear the floor by 0 to
1/8 inch (0 to 3mm).
REPLACING THE HOPPER SEALS
1. Park the machine on a smooth, level floor.
2. Raise the hopper and engage the hopper safety
arm.
HOPPER LIP SKIRTS
The hopper lip skirts seal the area between the lip of
the hopper and the floor. They also help deflect
debris into the hopper. The lip skirts should be
inspected for wear or damage daily. The lip skirts do
not require adjustment. They should be replaced
when the lower edge is worn down to the “Perform
Alert™” wear indicator line.
Raised hopper may fall. Engage hopper safety
arm.
3. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
REPLACING THE HOPPER LIP SKIRTS
1. Empty the debris hopper.
4. Remove the retaining bolts and retaining bar.
5. Replace the worn hopper seal with a new seal.
6. Install the retaining bar and bolts.
2. Park the machine on a smooth, level floor.
3. Raise the hopper and engage the hopper safety
arm.
7. Adjust the hopper side seals.
ADJUSTING THE HOPPER SIDE SEALS
Raised hopper may fall. Engage hopper safety
arm.
1. Park the machine on a smooth, level floor.
2. Raise the hopper and engage the hopper safety
arm.
4. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
Raised hopper may fall. Engage hopper safety
arm.
5. Remove the retainer plate on the right side of
the hopper.
3. Turn off machine and set parking brake.
6. Loosen the four lip skirt retaining bolts.
7. Slide the four hopper lip skirts out of the retainer
plate.
8. Slide the new hopper lip skirts into place.
9. Tighten the retaining bolts and replace lip skirt
retainer.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
4. Loosen the three adjustment bolts.
5. Adjust the hopper side seals for correct floor
clearance, then tighten the adjustment bolts.
6. Connect the batteries and lower the hopper.
QTFSG/QTFSD 98349 05/15/03
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
HOPPER DOOR SEALS
4. Check the distance from the lower rear edge of
the hopper to the floor. The correct clearance is
2 inches (51 mm). The clearance should be
equal from side to side. A good method for
checking this clearance is to slide a 2 inch
(51mm) high bar under the hopper.
5. If necessary, loosen the two rear hopper
attachment bolts, raise or lower the rear of the
hopper to obtain the correct floor clearance, and
tighten bolts.
The hopper door seals prevent debris from spilling
out of the hopper before dumping. There are two
hopper door side seals, one hopper door lower seal
and one hopper door upper seal. The upper seal
can only be replaced by removing the hopper door
from the hopper. The hopper door seals should be
inspected for wear or damage daily. They do not
require adjustment.
REPLACING DOOR SEALS
HOPPER DUST FILTER
1. Empty the debris hopper.
The hopper dust filter cleans the dust laden air that
is drawn up from the hopper by the vacuum impeller.
The filter is located above the hopper and is
accessed by raising the filter cover. The filter should
be cleaned daily by pressing the filter shaker button
for 10-20 seconds. The filter should be removed,
cleaned and inspected after every 100 hours of
operation. Replace if damaged.
2. Park the machine on a smooth, level floor.
3. Raise the hopper and engage the hopper safety
arm.
Raised hopper may fall. Engage hopper safety
arm.
4. Partially open the hopper dump door so that
both sides of the hopper door can be accessed.
5. Turn off machine and set parking brake.
TO REMOVE AND REPLACE HOPPER DUST
FILTER
1. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
6. Remove the retainer bar from the worn or
damaged seal.
2. Raise the filter cover.
7. Remove the old seal and place the new seal in
position.
3. Loosen the four filter retaining bolts.
4. Rotate the lower two filter retaining tabs down.
5. Lift the left side of the upper filter retaining bar to
clear the retaining bolt and swing the bar down
to clear the right side of the filter panel.
6. Remove the filter.
NOTE: When replacing the lower door seal, a new
seal cord must be used.
8. Replace the seal retaining bar. Replace and
7. After inspection or cleaning, install the dust filter
with the air flow arrow pointing up.
tighten the screws.
8. Replace the filter retaining bar, and the two
HOPPER
lower retaining tabs. Tighten the bolts.
The hopper holds debris swept by the main broom.
The hopper should be dumped after each day of
operation and cleaned every 200 hours of operation.
For efficient sweeping, the correct hopper floor
clearance must be maintained.
1. Empty the hopper.
2. Park the machine on a smooth, level floor.
3. Turn off machine and set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
QTFSG/QTFSD 98349 05/15/03
4-12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
To clean the filter after removal, use one of the
following methods:
TIRES
Tires should be inspected after every 100 hours of
operation. Pneumatic tires should be inflated to 90
PSI.
1. TAPPING Tap the filter frame gently on the
dirty side of the filter down. Be
careful not to dent the filter frame.
2. AIR
Blow compressed air through the
filter opposite the direction of the
arrow on the side of the filter. This
may be done with filter in the
machine. Wear eye and dust
inhalation protection when using
compressed air.
3. WATER
The filter can be soaked in water
and mild detergent. Rinse the filter
until it is clean. Air dry the filter.
NOTE: Do not install the filter until it is completely
dry.
BRAKES (Refer to the Brake Group in the Parts
section)
The brake pedal and the parking brake operate the
two front tire disc brakes. The disc brakes should be
checked every 200 hours of operation, and adjusted
if necessary. The disc brakes should be adjusted so
that the disc pads are as close to the brake disc as
possible, without causing the brakes to drag.
TO ADJUST THE BRAKES
1. Raise the hopper.
2. Engage the hopper safety arm.
Raised hopper arm may fall. Engage hopper
safety arm.
3. Turn off machine. Do not set parking brake.
FOR SAFETY: Before leaving or servicing machine,
stop on level surface, apply parking brake, turn off
machine and remove key.
4. Raise rear cover.
5. Disconnect batteries from machine.
6. Locate the brake adjustment screw on each
brake caliper.
7. Loosen the locknut and turn the adjusting screw
to adjust each brake. Tighten the locknut.
8. Lower the hopper.
9. Test brakes before beginning normal operations.
QTFSG/QTFSD 98349 05/15/03
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
BATTERY
BATTERY MAINTENANCE
The battery provides the power to start the machine.
The battery requires regular maintenance to keep
them operating at peak efficiency.
1. When cleaning the battery, use a solution of
baking soda and water. Do not allow the
cleaning fluid to enter the battery cells.
Electrolyte will be neutralized.
2. Maintain the proper electrolyte level in each
battery cell. If a cell should accidentally
overflow, clean immediately.
3. Do not add water until the battery is fully
charged.
4. Wipe off the top of the batteries at least once a
week.
To get the greatest life from the battery charge it
when their charge level reaches 25%of a full charge.
Use a hydrometer to check the charge level.
Do not allow the battery to remain in a discharged
condition for any length of time. Never expose a
discharged battery to temperatures below freezing.
Discharged batteries will freeze causing cracked
case. Do not operate the machine if the battery is in
poor condition or if they have a charge level below
25%, specific gravity below 1.177.
5. Test battery condition with a hydrometer at least
once a week.
Keep all metallic objects off the top of the battery, as
they may cause a short circuit. Replace worn or
damaged cables and terminals.
6. Ensure that all connections are tight and all
corrosion removed.
Check the electrolyte level in each battery cell
before and after charging the battery. Never add
acid to the battery, use water. Do not allow water
level to fall below the battery plates. Portions of
plates exposed to air will be destroyed. Do not
overfill. Keep plugs firmly in place at all times.
The battery in this machine is rated at 12V, 550cca.
It is located under the engine, center of frame.
When removing the battery cables, remove the
negative (-) cable before removing the positive (+)
cable.
7. Every 4 to 6 months, remove the batteries from
the machine and clean the battery cases and
battery compartment.
NOTE: Do not take readings immediately after
adding water. If the water and acid are not
thoroughly mixed, the reading may not be accurate.
! WARNING
When servicing machine, avoid contact with
acid.
! WARNING
Batteries emit hydrogen gas. Explosion or fire
can result. Keep sparks and open flame away.
Keep covers open when charging.
! WARNING
Wear eye protection and protective clothing
when working with batteries.
To find the correct specific gravity reading when the
temperature of the battery electrolyte is other then
80L F (27L C).
! WARNING
SPECIFIC GRAVITY
BATTERY CONDITION
1.265
1.225
1.190
1.155
1.120
100% CHARGED
75% CHARGED
50% CHARGED
25% CHARGED
DISCHARGED
Charge batteries in a well-ventilated area.
Add (+) to the specific gravity reading
0.004 (4 points), for each 10L F (6L C) above 80L F
(27L C) Subtract (-) from the specific gravity reading
0.004 (4 points), for each 10L F (6L C) below 80L F
(27L C).
QTFSG/QTFSD 98349 05/15/03
4-14
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC SCHEMATIC
HYDRAULIC TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
Loss of power to rocker
switch
Hopper will not lift
Key switch must be on check circuit breaker
Low hydraulic fluid
Hopper overloaded
Rocker switch failure
Speed control orifice
plugged
Add hydraulic fluid
Empty hopper
Test – replace switch
Clean or replace orifice (located behind the lower
cylinder fitting)
Pump solenoid failure
Check valve failure
Lift cylinder failure
Gear pump failure
Loss of power to rocker
switch
Replace pump solenoid
Replace check valve or solenoid
Replace cylinder seals
Replace pump or pump motor
Hopper will not lower
Key switch must be on, check circuit breaker
Rocker switch failure
Speed control orifice
plugged
Test – replace switch
Clean or replace orifice (located behind the lower
cylinder fitting)
Check valve failure
Replace check valve or solenoid
QTFSG/QTFSD 98349 05/15/03
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
PROPEL SYSTEM TROUBLESHOOTING
PROBLEM.
No propelling
CAUSE
SOLUTION
Low battery charge
Controller overheated
Loose or broken wires or
motor failure
Blown fuse (120A)
Main contactor failure
Charge battery.
Thermal switch tripped. Allow cool down period.
Located, then fix or replace wire(s). Check motor for
binding. Check motor for failure.
Replace fuse.
Replace main contactor.
Key operated on/off switch Replace on/off switch.
failure
Chain failure
Repair chain.
Machine moves without Throttle not set at “neutral“ Adjust linkage.
pressing foot pedal
Full speed only
Machine will not reach
full speed
position
Pedal linkage frozen
Transmission belt slipping
or linkage needs
adjustment
Repair or adjust linkage.
Charge battery.
Forward speed only
Reverse speed only
Sporadic operation
Transmission failure
Transmission failure
Transmission failure
Inspect, repair or replace.
Inspect, repair or replace.
Inspect, repair or replace.
QTFSG/QTFSD 98349 05/15/03
4-16
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE TROUBLESHOOTING
PROBLEM.
CAUSE
SOLUTION
Excessive dusting
Dust skirts and seals worn, Replace or adjust skirts or seals.
damaged, not adjusted
properly
Dust filter clogged or
damaged
Shake and clean or replace filter.
Vacuum hose damaged
Vacuum fan not operated
Broom bristles worn
Replace vacuum hose.
Belt loose, broken or off pulley.
Replace brooms.
Poor sweeping
performance
Brooms not adjusted
properly.
Adjust brooms.
Debris caught in broom
drive mechanism.
Free mechanism of debris.
Main broom drive failure
Side broom drive failure
Belt loose, broken or off pulley.
Check circuit breaker. Check side broom motor
circuit.
Hopper dump door closed
Hopper full
Open dump door.
Empty hopper.
Hopper floor skirts worn,
damaged
Replace skirts.
Machine travels slowly Parking brake set
Release parking brake.
or not at all
Towing valve activated.
Release towing valve.
Linkage broken or not
properly adjusted
Transmission drive belt
slipping or broken
Main engine drive belt
failure
Inspect and adjust or repair.
Inspect and repair.
Inspect and repair.
Inspect and repair.
Differential drive chain
failure.
QTFSG/QTFSD 98349 05/15/03
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SERVICE SCHEDULE
MAINTENANCE
Check and add fuel (see Engine’s
Owner’s Manual supplied)
Check and add engine oil (see
Engine’s Owner’s Manual supplied)
Check for fuel, oil and coolant leakage
(see Engine’s Owner’s Manual
supplied)
DAILY
WEEKLY
50HRS
*
*
*
Check radiator for dust and insects
(see Engine’s Owner’s Manual
supplied)
Check water level of batteries after
charging
*
*
Check main broom & side broom
adjustment, remove string, etc – check
for damage
*
*
Check main broom skirts and seals
Check hopper lip skirts for damage and
wear
Visually check tires for damage and
proper inflation
Check for leaks under hydraulic power
unit and at cylinder
*
*
*
Check hopper side seals for
adjustment and wear
Check hopper top seals for wear
*
*
Check air pressure in pneumatic tires
(90PSI)
Check air cleaner foam element (see
Engine’s Owner’s Manual supplied)
Rotate main broom end-for-end
*
*
*
*
*
*
Check skirt floor clearance
Tighten wheel nuts
Check carburetor adjustment
NOTE: More frequent intervals may be required in extremely dusty conditions.
QTFSG/QTFSD 98349 05/15/03
4-18
Download from Www.Somanuals.com. All Manuals Search And Download.
|