Yamaha MiniDisc Player MDX 595 User Manual

M D X -5 9 5

NATURAL SOUND MINIDISC RECORDER

LECTEUR ENREGISTREUR MINIDISC

OWNER’S MANUAL

MODE D’EMPLOI

Download from Www.Somanuals.com. All Manuals Search And Download.

FCC INFORMATION (for U.S. customers only)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void

your authority, granted by the FCC, to use the product.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product

is found to be the source of interference, which can be

determined by turning the product “OFF” and “ON”, please

try to eliminate the problem using one of the following

measures:

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded

cables. Cables supplied with this product MUST be used.

Follow all installation instructions. Failure to follow

instructions could void your FCC authorization to use this

product in the USA.

Relocate this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will not

result in harmful interference with other electronic devices.

If these corrective measures do not produce satisfactory

results, please contact your local retailer that is authorized to

distribute this type of product. If you cannot locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the

operation of other electronic devices.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the most out of

your equipment by playing it at a safe level. One that lets the

sound come through loud and clear without annoying blaring

or distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is

often undetectable until it is too late,

YAMAHA and the Electronic Industries

Association’s Consumer Electronics Group

recommend you avoid prolonged exposure

to excessive volume levels.

Want You

LISTENING

For A Lifetime

For Canadian Customers

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

Download from Www.Somanuals.com. All Manuals Search And Download.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1. This unit is a sophisticated mini disc recorder. To ensure

proper operation for the best possible performance, please

read this manual carefully.

For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note: The plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is hazardous

if engaged in a live socket outlet.

2. Install your unit in a cool, dry, clean place with good

ventilation. Avoid placing it in direct sunlight, near sources of

heat, or in locations subject to vibration, excessive dust, heat,

cold, or moisture. To avoid humming sounds, position the unit

away from other electrical appliances, motors, and

transformers.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

3. Do not operate the unit upside-down. It may overheat,

possibly causing damage.

ACCORDANCE WITH THE FOLLOWING CODE:

4. Do not place another component on top of this unit, to do so

may discolor or damage the surface of the unit.

Blue: NEUTRAL

Brown: LIVE

5. Do not open the cabinet of this unit, to do so may result in

damage to the unit or electrical shock. If any foreign object or

substance gets into the unit, contact your dealer for

assistance.

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug, proceed

as follows: The wire which is coloured BLUE must be

connected to the terminal which is marked with the

letter N or coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

6. When removing the power plug from the wall outlet, always

pull directly on the plug; never pull the cord itself.

7. Do not apply excessive force when operating switches and

knobs.

8. When moving the unit, be sure to first disconnect the power

cord from the AC outlet and disconnect all cords connecting

the unit to other equipment.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

9. To prevent damage by lightning, disconnect the power cord

from the wall outlet during an electrical storm.

CAUTION FOR CARRYING THE UNIT

Before carrying the unit, first remove a disc from the unit,

press POWER to turn the unit off, then disconnect the AC

power plug from the wall outlet.

10. Do not attempt to clean this unit with chemical solvents as this

may damage the finish. Use a clean, dry cloth.

11. Be sure to read the “TROUBLESHOOTING” section for advice

on common operating errors before concluding that your unit

is faulty.

WARNING

12. Keep this manual in a safe place for future reference.

To reduce the risk of fire or electric shock, do not expose this

appliance to rain or moisture.

13. The voltage to be used must be the same as that specified on

this unit. Using this unit with a higher voltage than that which is

specified is dangerous and may result in a fire or other type of

accident causing damage. YAMAHA will not be held

To avoid electrical shock, do not open the cabinet.

Refer servicing to qualified personnel only.

responsible for any damage resulting from use of this unit with

a voltage other than that which is specified.

DANGER

Invisible laser radiation when open and interlock failed or

Note

defeated. Avoid direct exposure to beam.

Please check the copyright laws in your country to record from

records, compact discs, radio, etc. Recording of copyright

material may infringe copyright laws.

CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

This mini disc recorder is

classified as a CLASS 1 LASER

product.

CLASS 1 LASER PRODUCT

The CLASS 1 LASER PRODUCT

label is located on the rear

exterior.

(U.K. and Europe models only)

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

CONTENTS

A sampling rate converter that lets you make

digital recordings from 32 kHz (DAT, etc.) , 44.1

kHz (CD, DAT, MD, etc.) and 48 kHz (DAT, etc.)

program sources.

PART DESCRIPTIONS........................................................ 4

FRONT PANEL ..................................................................... 5

REMOTE CONTROL............................................................. 6

CONNECTIONS ................................................................... 7

ANALOG CONNECTIONS ................................................... 7

DIGITAL CONNECTIONS .................................................... 7

PLAYBACK .......................................................................... 8

Skipping Tracks ................................................................ 8

Searching .......................................................................... 9

Switching the Display ....................................................... 9

RANDOM PLAY .................................................................. 10

REPEAT PLAY .................................................................... 10

Single Track Repeat ....................................................... 10

Full Disc Repeat.............................................................. 10

Part (A-B) Repeat............................................................ 11

PROGRAM PLAY................................................................ 11

RECORDING...................................................................... 13

Adjusting Recording Levels ........................................... 14

Auto Marking ................................................................... 15

TIME RESCUE RECORDING ............................................. 15

SYNCHRO RECORDING.................................................... 16

MONAURAL RECORDING................................................. 16

MONITOR OUT................................................................... 17

EDITING ............................................................................. 18

MOVE .................................................................................. 18

ERASE................................................................................. 19

Disc Erase ....................................................................... 19

Track Erase ..................................................................... 19

Part Erase........................................................................ 20

Disc or Track Title Erase ................................................ 20

COMBINE ........................................................................... 21

DIVIDE ................................................................................ 21

Disc Maintenance .............................................................. 22

TOC WRITE ..................................................................... 22

FRA CHECK .................................................................... 22

TITLING .............................................................................. 23

TIMER OPERATIONS ....................................................... 24

Timer Recording ............................................................. 24

Timer Playback ............................................................... 24

MD SYSTEM LIMITATIONS.............................................. 25

COPY PROTECTION (SCMS) .......................................... 26

NOTES REGARDING THE REMOTE CONTROL............ 26

Remote Control Operation Range.................................. 26

Battery Installation .......................................................... 26

TROUBLESHOOTING ....................................................... 27

DISPLAY MESSAGES ...................................................... 28

SPECIFICATIONS ............................................................. 29

Editing features (MOVE, ERASE, DIVIDE,

COMBINE, TITLE, and UNDO) that let you take

full advantage of the MD recording system.

Multiple digital input terminals (2 optical inputs)

let you connect two different digital program

sources.

The digital optical output terminal lets you output

digital audio from an MD.*

In addition to the standard disc and track repeat

modes, this unit also has a part (A-B) repeat

mode that lets you repeat a specific part of a

track.

Synchro Record lets you make synchronized

recordings from any type of source component.

Time Rescue Record monitors the sound being

input and allows you to recover sound input from

a point approximately six seconds before you

start the recording operation. (So you will not

miss the beginning of a song when recording

directly from the radio, etc.)

The Monaural Record mode lets you record up to

148 minutes of audio onto one MD.

Timer playback and recording modes that let you

start playback or recording at a preset time using

an optional audio timer.

* This is not possible if MD is a direct copy of another digital

signal (see page 26 for details regarding SCMS copy

protection).

US and foreign patents licensed from Dolby Laboratories

Licensing Corporation.

Download from Www.Somanuals.com. All Manuals Search And Download.

PART DESCRIPTIONS

Front Panel

⁄

¤ # ‹

T U

IN ID IS

E C

E R

–5

E R

)E J E C

E C

#˜*

DIGITAL

REC LEVEL

ANALOG

TIMER

OFF

–

REC LEVEL

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

1 0

› % ﬁ ^ ﬂ & ‡ * ° (

)

‚ _

—

Remote Control

DISPLAY SCROLL

A–B

REPEAT

(

ﬁ

–

)

RNDM

PROG

A B C

D E F

G H I

K L

Q R

T U

V W

Y Z

⁄

SPACE

+1 0

ﬂ

TITLE

CHAR. NUMBER DELETE

SET

‡

(

M-MARK MONO/ ST INPUT

REC

SKIP

TIME

SYNC

‹

PLAY

PAUSE

STOP

REC

CD-P

›

)

‚

M DX

Download from Www.Somanuals.com. All Manuals Search And Download.

FRONT PANEL

See the pages in parenthesis for details regarding operation.

~ POWER (8)

ﬂ SCROLL (9)

Press to turn the unit on or off.

Press to scroll the disc (track) title across the display.

Press while scrolling to pause the scroll. Press and

hold to scroll rapidly.

Ÿ Disc insertion slot

Insert the disc into this slot.

& TITLE (23)

! ) EJECT

Press to activate or deactivate the title mode.

Press to remove the disc.

If the TOC* data has not yet been written, it is written

automatically before the disc is ejected.

‡ CHARA. (23)

Press repeatedly to select different types of characters

when creating a disc (track) title.

⁄ Remote control sensor (26)

Receives the signals emitted from the remote control.

* DELETE/CANCEL (23, 18)

Press to cancel an edit function or to delete the

selected character when titling a disc (track).

@ Display panel (9)

Displays various system information.

° EDIT (18)

¤ #/* (8, 14)

Press repeatedly to access the different edit modes.

Press during stop (or pause) to start playback. Press

while playing to pause.

( SET/ENTER (23, 18)

Press during record pause to start recording. Press

while recording to pause.

Press to confirm an edit operation or enter a character

in the title mode.

# & (8, 13, 18, 23)

· Jog dial ($ ›)/DIGITAL REC LEVEL (8, 14, 18, 23)

Use to adjust the digital recording level when

recording digital audio sources.

Press to stop recording or playback.

Press to cancel an edit or title input operation.

Use to skip to the beginning of previous tracks or

advance to later tracks.

Use to select characters when creating a disc (track)

title.

‹ REC (14)

Press during stop or pause to activate the record

pause mode.

$ TIMER (24)

) SEARCH ! ⁄ (9, 23)

Use to set the unit to play or record when activated by

an external timer.

Press and hold to search quickly during play or pause.

Use to move the cursor when creating a disc (track)

title.

› RANDOM (10)

Press to activate or deactivate the random play mode.

‚ INPUT (13)

Press repeatedly to select the input jacks you want to

record from: ANALOG or DIGITAL (OPTICAL 1 or

OPTICAL 2).

% REPEAT S/F (10)

Press to select single track (S) or full disc (F) repeat.

ﬁ REPEAT A-B (11)

_ ANALOG REC LEVEL (14)

Use to adjust the recording level when recording from

the analog inputs.

Press to specify the A and B points for A-B repeat.

^ DISPLAY (9)

Press repeatedly to switch between the title and time

— PHONES (12)

displays.

PHONES jack

For connecting stereo headphones.

PHONES LEVEL knob

Turn to adjust the volume of the headphones

connected to the PHONES jack.

* TOC (Table of Contents): This is the non-audio data

contained on all mini discs (track numbers, playback

time, title data, etc.).

UTOC (User’s Table of Contents): This is non-audio data

that you can edit (like track numbers, playback time, and

title data).

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE CONTROL

See the pages in parenthesis for details regarding operation.

~ REPEAT (10)

ﬁ SCROLL (9)

Press to scroll the disc (track) title across the display.

Press while scrolling to pause the scroll. Press and

hold to scroll rapidly.

S/F [ ! ]

Press to select single track (S) or full disc (F) repeat.

Press to select “!” when creating a disc (track) title.

^ NUMBER (23)

A-B [ ? ]

Press before pressing a number button to input a

number during title mode.

Press to specify the A and B points for A-B repeat.

Press to select “?” when creating a disc (track) title.

ﬂ DELETE (23)

Ÿ PROG [ – ] (11)

Press to delete the selected character when creating a

disc (track) title.

Press to activate or deactivate the program play mode.

Press to select “–” when creating a disc (track) title.

& SET (23)

! RNDM [ & ] (10)

Press to confirm selected character when creating a

disc (track) title.

Press to activate or deactivate the random play mode.

Press to select “&” when creating a disc (track) title.

‡ M-MARK (15)

⁄ Numbers [Characters] (8, 23)

Use to specify a track.

Press to select automatic or manual marking of tracks

during recording.

Press repeatedly to select a character when creating a

disc (track) title.

* INPUT (13)

Press repeatedly to select the input jacks you want to

record from: ANALOG or DIGITAL (OPTICAL 1 or

OPTICAL 2).

@ CHAR. (23)

Press repeatedly to select uppercase or lowercase

letters during title mode.

° MONO/ST (16)

¤ TITLE (23)

Press during stop or pause to select either monaural or

stereo recording.

Press to activate or deactivate the title mode.

# SEARCH ! ⁄ (9, 23)

( Special Record buttons

Press and hold to search quickly during play or pause.

Use to move the cursor when creating a disc (track)

title.

TIME (15)

Press during record pause mode to activate Time

Rescue Recording.

‹ SKIP $ › (8, 23)

SYNC (16)

Press to skip back to the beginning of previous tracks

or advance to later tracks during play, pause or stop.

Use to select characters when creating a disc (track)

title.

Press during stop to activate Synchronized Recording.

· CD-P (16)

Press to start playback from a YAMAHA CD player.

$ PLAY # (8, 14)

) REC ? (14)

Press during stop (or pause) to start playback.

Press during record pause to start recording.

Press during stop or pause to activate the record

pause mode.

› PAUSE * (8, 14)

‚ STOP & (8, 13, 18, 23)

Press to pause playback or recording.

Press to stop recording or playback.

Press to cancel an edit or title input operation.

% DISPLAY (9)

Press repeatedly to switch between the title and time

displays.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTIONS

Do not plug in this unit (or other components) until all connections are complete.

• Connections should be made to the correct input/output terminals on the other component.

• Also refer to the owner’s manual supplied with the component you are connecting.

• If the placement of this unit causes noise in other equipment, such as a tuner, move them farther apart.

ANALOG CONNECTIONS

Audio connecting cords (included)

PLAY

REC

DIGITAL

OPTICAL

ANALOG

IN OUT

OUT

Amplifier/Receiver

(REC) (PLAY)

To AC outlet

Notes for analog connections

• The white plug on the audio connecting cords corresponds to the L (left) channel and the red plug corresponds to the R (right) channel.

Be sure to connect L (left) to L and R (right) to R. Also make sure that the plugs are fully inserted and that the connection is firm.

• The LINE OUT jacks on the MD recorder should be connected to the MD PLAY jacks on your amplifier.

The LINE IN jacks on the MD recorder should be connected to the MD REC jacks on your amplifier.

• The LINE OUT terminals on this unit are numbered 3 and the LINE IN jacks are numbered 4. When connecting this unit to a YAMAHA

amplifier or receiver whose terminals are numbered 1, 2, 3, 4 ... (etc.), connect this unit’s LINE OUT terminals to the input terminals

numbered 3 and connect this unit’s LINE IN terminals to the output terminals numbered 4 on the rear panel of the amplifier or receiver.

DIGITAL CONNECTIONS

Optical fiber cable (included)

DIGITAL OUT

OPTICAL

DIGITAL

OPTICAL

ANALOG

IN OUT

OUT

CD player (etc.) with

optical OUT

Amplifier/Receiver

(or MD/DAT recorder)

with optical IN/OUT

(REC) (PLAY)

To AC outlet

DIGITAL IN

OPTICAL

DIGITAL OUT

OPTICAL

*Optical fiber cable

* One optical fiber cable is included with

the MDX-595. Additional OPTICAL

connections should be made using

commercially available optical fiber cables.

*Optical fiber cable

Notes for digital connections

• The DIGITAL IN terminals can be connected to any component with an optical output so you can make direct digital recordings.

• The DIGITAL OUT terminal can be connected to a any component with an optical input so you can output digital audio from an MD.

• Before making OPTICAL connections, remove the terminal cover(s).

• In order to protect the terminals from dust, be sure to attach the terminal covers when the optical terminals are not being used.

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK

Preparations

To stop

• Be sure to set the TIMER switch to OFF, then press

POWER to turn this unit on.

• Set your amplifier or receiver to MD.

Press & (STOP & on the remote).

To pause

Press #/* (PAUSE * on the remote).

Press again to resume playback (or press PLAY # on the

remote).

) EJECT

IN ID IS

–5

To eject the MD

)

#˜*

Press ) EJECT.

DIGITAL

REC LEVEL

ANALOG

REC LEVEL

TIMER

OFF

–

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

Note

The MONO indicator lights when playing monaural MDs.

jog dial SEARCH ! ⁄

Skipping Tracks

To skip to the next track

Turn the jog dial to the right (or press SKIP › on the

remote).

DISPLAY SCROLL

A–B

REPEAT

(

–

)

RNDM

PROG

Numbers

To skip to a previous track

SPACE

+1 0

Turn the jog dial to the left (or press SKIP $ on the

remote).

Turn one click to skip to the beginning of the current track.

Turn an additional click to skip back to the beginning of

each previous track.

! ⁄

TITLE

CHAR. NUMBER DELETE

SET

M-MARK MONO/ ST INPUT

REC

⁄

SKIP

›

TIME

SYNC

SKIP

PLAY

PAUSE

STOP

REC

$ ›

‹

CD-P

To skip to a specific track number

M DX

Press the number buttons on the remote corresponding to

the track you desire.

PAUSE *

STOP &

Example:

To select track 3, press 3.

To select track 13, press +10, then press 3.

To select track 23, press +10 twice, then press 3.

1 Insert an MD.

To skip to the last track on the disc

Label facing up

Turn the jog dial to the left when the display is showing the

total tracks and total playing time.

IN ID IS

–7

Arrow pointed toward

disc insertion slot

2 Press #/* (PLAY # on the remote) to start

playback.

3 Adjust the volume using the volume control on

your amplifier or receiver.

Download from Www.Somanuals.com. All Manuals Search And Download.

Searching

2 Time remaining on the MD (only for recordable MDs)

To search forward during play or pause

REMAIN indicator

Time remaining on the MD

Press and hold SEARCH ⁄.

DISC TRACK

TOTAL

REMAIN

To search in reverse during play or pause

Press and hold SEARCH !.

Notes

Total tracks

• Sound can be heard when searching in play mode to help you

locate the desired position within the track. No sound is heard

when searching in pause mode, but the search is conducted

at a higher speed.

• When searching in play mode, playback stops when you

reach the end of the last track.

3 Disc title

DISC TRACK

TOTAL

REMAIN

• Search may not function correctly when there are several

consecutive tracks consisting of only a few seconds each.

During playback

Switching the Display

Press DISPLAY repeatedly to display the following

information.

When you insert an MD, the disc title is displayed

1 Current track number and elapsed time

automatically (“No Title” appears if there is no disc title).

Pressing DISPLAY during stop or playback to display other

information, such as the remaining time and track titles.

Track number

Elapsed time

DISC TRACK

TOTAL

REMAIN

IN ID IS

–5

)

#˜*

2 Time remaining on the current track

DIGITAL

REC LEVEL

ANALOG

REC LEVEL

TIMER

OFF

–

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

REMAIN indicator

DISC TRACK

TOTAL

REMAIN

DISPLAY

SCROLL

3 Track title

DISPLAY SCROLL

If the track has not been given a name, “No Title” is

displayed and the display switches back to the elapsed time

(1).

A–B

REPEAT

(

SCROLL

DISPLAY

–

)

RNDM

PROG

DISC TRACK

TOTAL

REMAIN

SPACE

+1 0

During stop

Press DISPLAY repeatedly to display the following

information.

To view the entire disc (track) title

If the disc (track) title is too long to fit in the display, press

SCROLL to move the title sequentially across the display.

While the title is being displayed, press SCROLL to pause

the display, and again to continue presentation of the title.

Press and hold SCROLL for rapid presentation of the title.

1 Number of tracks and total playing time

Total tracks

Total playing time

DISC TRACK

TOTAL

REMAIN

Download from Www.Somanuals.com. All Manuals Search And Download.

RANDOM PLAY

REPEAT PLAY

You can have the unit play all the tracks on a disc in

random order.

You can have the unit repeat a single track, a full disc, or

just part of a track.

IN ID IS

–5

IN ID IS

–5

#˜*

)

#˜*

DIGITAL

REC LEVEL

DIGITAL

REC LEVEL

ANALOG

TIMER

OFF

TIMER

OFF

–

REC LEVEL

PHONES

LEVEL

–

REC LEVEL

PHONES

LEVEL

›

REC

PLAY

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

RANDOM

S/F – REPEAT

A-B – REPEAT

DISPLAY SCROLL

A–B

REPEAT

(

A–B

REPEAT

(

S/F – REPEAT

A-B – REPEAT

–

)

–

)

RNDM

PROG

RNDM

PROG

RNDM

SPACE

+1 0

SPACE

+1 0

Single Track Repeat

To start random playback

Press RANDOM (RNDM on the remote).

The RANDOM indicator lights up and “Random Search”

appears in the display while the unit selects a track.

Playback starts automatically.

1 Select the track you want to repeat.

2 Press S/F – REPEAT repeatedly to light the

REPEAT S indicators.

REPEAT

A-BSF

To cancel

Press RANDOM (RNDM on the remote) again to turn off the

To cancel

RANDOM indicator.

Press S/F – REPEAT repeatedly to turn off the REPEAT S

indicators.

Notes

• Pressing SKIP › during random play skips to another track

at random. Pressing SKIP $ returns to the beginning of the

current track (you cannot return to previously played tracks).

• If you turn the unit off during random playback, it will be ready

for random play the next time you turn the power back on.

Note

Single track repeat is not available during random or program

playback.

Full Disc Repeat

Press S/F – REPEAT repeatedly to light the REPEAT

F indicators.

REPEAT

A-BSF

To cancel

Press S/F – REPEAT repeatedly to turn off the REPEAT F

indicators.

Notes

• In program play mode, the entire program is played

repeatedly.

• In random play mode, the unit reshuffles the tracks and plays

them again after each track plays once.

Download from Www.Somanuals.com. All Manuals Search And Download.

Part (A-B) Repeat

PROGRAM PLAY

This function lets you repeat a specific part of a track. It’s a

convenient way to study a language, or to learn the lyrics to

your favorite song (etc.).

This function lets you enjoy listening to your favorite tracks

in any order you desire.

1 Press A-B – REPEAT during playback to specify

the beginning (A point) of the part you want to

repeat.

DISPLAY SCROLL

The REPEAT A indicators light up.

A–B

REPEAT

(

–

)

RNDM

PROG

REPEAT

A-BSF

SPACE

+1 0

2 Press A-B – REPEAT again to specify the end (B

point) of the part you want to repeat.

The REPEAT A-B indicators light up and the part you

specified starts to repeat.

DELETE

TITLE

CHAR. NUMBER DELETE

SET

! ⁄

M-MARK MONO/ ST INPUT

REC

⁄

SKIP

›

SKIP

TIME

SYNC

PLAY

PAUSE

STOP

REC

$ ›

‹

CD-P

REPEAT

A-BSF

M DX

To cancel

Press & or A-B – REPEAT.

1 Press STOP & to stop playback.

2 Press PROG to light up the PROGRAM indicator.

3 Program the desired track by pressing the

corresponding numeric buttons.

Example:

To select track 3, press 3.

To select track 13, press +10, then press 3.

To select track 23, press +10 twice, then press 3.

The following display appears momentarily to

show the step information:

Step number

Track number

PROGRAM

The display then switches to the program status:

Total steps

Total playing time

TOTAL

PROGRAM

Repeat this operation to program up to 30 steps.

4 Press PLAY # to start program playback.

Continued on next page

Download from Www.Somanuals.com. All Manuals Search And Download.

To check the programmed data

To use headphones for private listening

Stop or pause program playback.

Press SKIP $ or › to skip through the step

information (or use the jog dial on the front panel).

Set the PHONES LEVEL knob on the front panel to “0”

(minimum) and insert the headphones plug of your stereo

headphones into the PHONES jack.

To adjust the volume level of the headphones

To delete a specific step

Use the PHONES LEVEL knob.

Stop program playback.

Turn toward “10” (maximum) to increase the volume.

Turn toward “0” (minimum) to decrease the volume.

Press SKIP $ or › to skip through the step

information (or use the jog dial on the front panel).

Press DELETE (or DELETE/CANCEL on the front

panel) to delete the step. The higher steps are

renumbered automatically.

To change a step

Stop program playback.

Press SKIP $ or › to skip through the step

information (or use the jog dial on the front panel).

Use the numeric buttons to program a new track

number for that step. The original track is cleared from

memory and the new track is programmed.

To cancel

Press PROG to turn off the PROGRAM indicator, eject the

disc, or press POWER to turn this unit off.

Notes

• If the total time exceeds 255 minutes “255mOver” is displayed

instead of the total time.

• SKIP $ or › can be used during playback to skip

between programmed tracks.

• SEARCH ⁄ can be used during playback to search through

all tracks in the current program.

• SEARCH ! can be used during playback to return to the

beginning of the current track.

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

This unit allows you to make recordings from a wide variety

of program sources (both analog and digital).

1 Insert an MD.

Label facing up

When recording an analog source (such as an LP or

cassette) this unit converts the analog signals to a

44.1 kHz digital signal before recording them onto the MD.

When recording a digital source, this unit converts the

digital signals to 44.1 kHz for recording onto the MD.

However, if you are recording a 44.1 kHz source signal

(such as a CD) there is no conversion. This unit can record

32, 44.1 and 48 kHz digital signals.

IN ID IS

–7

Arrow pointed toward

disc insertion slot

2 Press INPUT repeatedly to select the input

connected to the sound source you want to

record.

Preparations

• Be sure to set the TIMER switch to OFF, then press

POWER to turn this unit on.

• Set your amplifier or receiver to the program source to be

recorded.

For

Select

LINE IN 4

ANALOG

DIGITAL IN OPTICAL 1

DIGITAL IN OPTICAL 2

DIGITAL OPT. 1

DIGITAL OPT. 2

) EJECT

Input indicator

IN ID IS

–5

ANALOG DISC TRACK

)

#˜*

DIGITAL

TOTAL

OPT. 1

COAX.

REMAIN

DIGITAL

REC LEVEL

ANALOG

REC LEVEL

TIMER

OFF

–

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

3 2 4 4 .1 4 8

RANDOM

ENTER

kHz

PROGRAM

REPEAT

A-BSF

(Source) sampling frequency indicators*

REC LEVEL

* Appears when digital signal is input.

3 Locate the point where you want to start

recording.

M-MARK

TITLE

CHAR. NUMBER DELETE

SET

M-MARK MONO/ ST INPUT

REC

• When recording on a blank MD

Skip this step.

• To start recording from the end of a previous recording

Press & to set this unit to stop mode.

• To record over a previous recording

Turn the jog dial (or press SKIP $ or › on the remote)

to select a track (recording starts from the beginning of the

deleted track), or press ^ (PAUSE * on the remote)

during playback to pause at the point where you want to

start recording.

⁄

SKIP

›

TIME

SYNC

PLAY

PAUSE

STOP

REC

‹

CD-P

PAUSE *

STOP &

M DX

Continued on next page

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting Recording Levels

4 Press REC (REC ‡ on the remote) to set this unit

to record pause mode.

Setting the digital volume level

The REC * indicators light up.

“REC Standby” and the amount of time available for recording

flash alternately in the display.

The volume level of digital audio sources is often similar,

however, level differences may be quite obvious between

different digital audio formats and even between one

recording and another. To maintain a consistent volume

level in MD recordings, it is possible to change the volume

of the input digital signal.

If you selected a track number or paused playback (in step

3) to record over a previous recording

“OverWrite OK?” appears in the display.

To confirm, press ENTER. This operation will erase the

selected track number (or point) and all subsequent material.

To cancel, press CANCEL (or &).

To select the digital signal to be recorded or monitored,

press INPUT repeatedly until the appropriate digital input

indicator (DIGITAL OPT. 1 or DIGITAL OPT. 2) appears in

the display. During record or record pause mode, turning

DIGITAL REC LEVEL adjusts the volume of the digital

signal. The digital volume can be adjusted up to +12 dB

and down to a minimum (MIN) level from the default volume

of 0 dB, the level of the input digital signal. To set the

volume level, play the digital source to be recorded and

adjust DIGITAL REC LEVEL so that highest peak causes

the 0 dB level indicators to flicker. The OVER indicators

should not light.

Adjust the recording level corresponding to the audio

input you selected in step 2. Refer to "Adjusting

Recording Levels" on this page for more details.

Note

When recording from a digital source that has a digital output

(volume) control, set the output level (volume) to “MAX”.

Recording may not be possible at low output levels (when the

digital volume is turned down).

5 Start playing the program source to be recorded.

6 Press #/* (PLAY # on the remote) to start

–

dB 00 6 0

3 0

1 0

OVER

recording.

The TOC indicator lights up.

When the TOC indicator is lit, this means that the TOC

information has not yet been written to the disc. After

recording is complete, the TOC data is automatically written to

the disc.

Should not light

If recording is stopped, the digital recording level is

restored to the default volume of 0 dB.

Notes

To stop

• When DIGITAL REC LEVEL is turned, the digital volume level

is adjusted in 0.5 dB steps between +12 dB and –20 dB, 1 dB

steps from –20 dB to –30 dB, 2 dB steps from –30 dB to –40

dB, followed by –44 dB, –48 dB, –54 dB, –62 dB and MIN.

• Although some sources can be recorded with lower peak

levels, setting the peak levels too low may degrade the quality

of the recording.

Press & (STOP & on the remote).

To pause

Press #/* (PAUSE * on the remote).

Press again to resume recording.

• The digital volume cannot be adjusted while a track title is

being entered.

To eject the MD

Press ) EJECT.

Setting the analog recording level

Press INPUT repeatedly until the ANALOG indicator

appears in the display, and press REC (REC ‡ on the

remote) to put this unit in the record pause or monitor out

mode. For best results, play the loudest passage of the

source to be recorded and watch the recording level meter

in the display. Adjust ANALOG REC LEVEL so that the

highest peak causes the 0 dB level indicators to flicker.

The OVER indicators should not light.

If the power to this unit is turned off while making a

recording, the TOC data cannot be correctly written to

the disc and the recorded data will be erased.

TOC writing may be impossible (or track number

marking may not perform as expected) when recording

a damaged CD or a broadcast source with

interference.

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto Marking

TIME RESCUE RECORDING

When making a recording, you can choose either

automatic or manual marking. This feature operates

somewhat differently for analog and digital signals. See

below for details.

The Time Rescue (TIME) recording function allows you to

start recording six seconds before you press record.

During record pause mode, the MD recorder monitors the

input signal and continuously maintains a six second

memory “cache”. Therefore, you can record a song that

just started without cutting off the beginning. You may find

this function useful when recording live broadcasts, or

when you want to start recording from the beginning of a

song without recording lots of commercials (etc.).

Press M-MARK on the remote repeatedly to select

automatic (MANUAL indicator out) or manual

(MANUAL indicator lit) marking.

MANUAL

When recording analog signals

TITLE

CHAR. NUMBER DELETE

SET

Auto : Track numbers are written in synchronization with

the input level of the signal being recorded. During

recording, if no sound is detected for more than 1.5

seconds, the recorder interprets this to be a gap between

two tracks. When the source signal is detected again, a

track number is automatically written.

M-MARK MONO/ ST INPUT

REC

⁄

SKIP

›

TIME

SYNC

PLAY

PAUSE

STOP

REC

‹

CD-P

M DX

Manual : One track number is written automatically when

you start recording, but none are written during recording.

To mark a track number, press M-MARK at the desired

position while recording.

Note

When using manual marking, the marks must be set at least 4

seconds apart.

1 Press INPUT repeatedly to select the input

connected to the sound source you want to

record.

When recording digital signals

Track numbers are written in the same positions as the original

source (CD, etc.) with either automatic or manual marking.

To add additional track numbers, set M-MARK to MANUAL

and press M-MARK at the desired position while recording.

2 Locate the point where you want to start

recording.

3 Press REC ‡ to set this unit to record pause

Notes

mode.

• When recording is paused, the portion recorded up to the

pause is counted as an individual track. When recording is

resumed, a new track number is created. On the other hand, if

one track is recorded in continuous repetition, that track is

recorded as one continuous track with a single track number.

• During synchronized recording, manual track marking is not

possible.

The REC * indicators light up.

“REC Standby” and the amount of time available for recording

flash alternately in the display.

To adjust the recording level of digital or analog input

sources, see “Adjusting Recording Levels” on page 14.

4 Press TIME to start recording when you hear the

beginning of a song you want to record.

Recording starts from the memory cache, allowing you to

record from a point approximately six seconds before you

pressed TIME.

Download from Www.Somanuals.com. All Manuals Search And Download.

SYNCHRO RECORDING

MONAURAL RECORDING

The synchronized recording function lets you set this unit

to start recording automatically when a sound signal is

input. When operating this unit in combination with a

remote controllable Yamaha CD player, you can use the

CD-P button on this unit’s remote control to start playback

from the CD player.

Recording in monaural (mono) allows you to record up to

148 minutes of sound on one 74 minute MD. (When

recording in stereo you can record up to 74 minutes of

sound.) This may be useful when recording an interview,

debate, or whenever you want to record for a long time on

one disc.

TITLE

CHAR. NUMBER DELETE

SET

TITLE

CHAR. NUMBER DELETE

SET

M-MARK MONO/ ST INPUT

REC

⁄

M-MARK MONO/ ST INPUT

REC

SKIP

⁄

›

TIME

SYNC

SKIP

PLAY

PAUSE

STOP

REC

›

TIME

SYNC

‹

CD-P

PLAY

PAUSE

STOP

REC

‹

CD-P

M DX

1 Load the sound source into the source

component.

1 Press INPUT repeatedly to select the input

connected to the sound source you want to

record.

If necessary, program, or select the track you want to

start recording from before proceeding to the next

step. (Refer to the operation manual supplied with the

source component for instructions regarding its use.)

2 Locate the point where you want to start

recording.

2 Press INPUT repeatedly to select the input

connected to the sound source you want to

record.

3 Press MONO/ST to light the MONO indicator.

4 Press REC ‡.

The REC * indicators light up.

3 Locate the point where you want to start

“REC Standby” and the amount of time available for recording

flash alternately in the display.

recording.

To adjust the recording level of digital or analog input

sources, see “Adjusting Recording Levels” on page 14.

4 Press SYNC to set this unit to record pause

mode.

The REC * indicators light up.

“Synchro REC” and the amount of time available for recording

flash alternately in the display.

5 Press PLAY # to start recording.

During synchronized recording, analog input sources are

recorded at the current ANALOG REC LEVEL setting, digital

sources are recorded at the 0 dB level.

5 Start playing the sound source. (Press CD-P if

recording from a Yamaha CD player.)

The MD starts recording automatically when a sound signal is

input. When the sound signal stops, the unit switches back to

record pause mode and “Synchro REC” blinks in the display.

6 To continue recording, repeat step 5.

When you have finished recording, press & on

this unit to cancel the record pause mode.

Note

When the signals at the beginning of a track are at a lower level

than the level required to start synchronized recording, they are

not recorded. Should this occur, perform manual recording.

Download from Www.Somanuals.com. All Manuals Search And Download.

MONITOR OUT

When a disc is not loaded, you can use the monitor out

function to monitor the sound of the input source. This

allows you to enjoy better sound from your other digital

source components, such as CD, by using this unit as a

digital to analog converter.

IN ID IS

–5

)

#˜*

DIGITAL

REC LEVEL

ANALOG

TIMER

OFF

–

REC LEVEL

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

1 Press ) EJECT to remove the disc.

2 Press INPUT repeatedly to select the input

connected to the sound source you want to

monitor.

3 Press REC.

“MONITOR OUT” appears in the display.

Sound from the selected input will be output from this unit’s

analog and digital output terminals.

4 Start playing the sound source selected in step 2.

The sound is output from the MD recorder’s analog and digital

output terminals.

To cancel

Press REC again, press &, or insert a disc.

Note

The digital volume can be adjusted when using the monitor out

function. However, please note that the digital volume setting is

restored to the default (0 dB) the next time a recording is made.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDITING

One of the main advantages of MD is its editing

MOVE

capabilities. You can remove the commercials from a radio

broadcast, reorder songs into the order you want, remove

songs, combine songs, and even remove part of a song.

This function lets you change the position of any track.

First, select the track you want to move, then specify the

track number you want to move it to. After the move, the

tracks located between the old and new positions are

renumbered automatically. You can perform this operation

repeatedly to completely reorder the disc.

Edit functions

This unit offers the following editing operations.

(Please note that track numbers are updated automatically

when you perform a MOVE, ERASE, COMBINE or DIVIDE

operation.)

IN ID IS

–5

)

#˜*

MOVE

DIGITAL

REC LEVEL

ANALOG

REC LEVEL

TIMER

OFF

Lets you move a track to a different track number.

–

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

ERASE

Lets you erase a track, the entire disc, or part of a

track. You can also erase the title of a disc, or the titles

of tracks on a disc.

CANCEL

2,4 1,3

1 Turn the jog dial to select the track you want to

COMBINE

Lets you combine two adjacent tracks.

move.

2 Press EDIT repeatedly to display “Move ?”, then

DIVIDE

press ENTER.

Lets you split a single track into two different tracks.

“Move (track number)=(track number)” appears in the

display.

TOC WRITE

Lets you write TOC information to the disc so that

changes are saved.

3 Turn the jog dial to select the track’s destination.

Destination

Selected track

FRA CHECK

Lets you recover disc space that may have been lost

after multiple edit operations.

ANALOG DISC TRACK

DIGITAL

TOTAL

OPT. 1

COAX.

REMAIN

UNDO

4 Press ENTER.

Lets you undo the previous edit operation if you make

a mistake (you cannot, however, undo the UNDO

function).

“Complete” appears momentarily in the display.

To cancel before moving the track

Press CANCEL (or &).

Note

After performing an edit operation, the TOC indicator lights to

show that the TOC information has not yet been written to the

disc. Undo is possible only when the TOC indicator is lit.

However, if you perform a recording operation (by pressing

REC, TIME, or SYNC), UNDO is not possible even if the TOC

indicator is lit.

To undo MOVE

Press & to put this unit in stop mode.

Press EDIT repeatedly to display “Undo Move”, then

press ENTER.

“Undo OK ?” appears in the display.

Press ENTER again to undo.

To cancel, press CANCEL (or &).

Download from Www.Somanuals.com. All Manuals Search And Download.

Track Erase

ERASE

The ability to erase sound without having to re-record is

another convenient function. You can erase the entire disc,

a single track, or just part of a track.

This operation lets you erase a single track as well as

corresponding title data. After you erase the track, the total

number of tracks decreases by one and all tracks following

that track are renumbered.

Disc Erase

IN ID IS

–5

This operation lets you erase all audio and title (character)

data to create a blank MD. Please note that once erased,

this data can be recovered using the UNDO function.

)

#˜*

DIGITAL

REC LEVEL

ANALOG

REC LEVEL

TIMER

OFF

–

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

CANCEL

2,3

IN ID IS

–5

)

#˜*

If you plan to erase two or more tracks

DIGITAL

REC LEVEL

ANALOG

TIMER

OFF

–

REC LEVEL

PHONES

LEVEL

›

REC

PLAY

To avoid confusion you should always erase from higher track

numbers to lower track numbers. This prevents accidental

renumbering of tracks you plan to erase.

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

CANCEL

2,3

1 Turn the jog dial to select the track you want to

erase.

1 Press & to set this unit to stop mode.

2 Press EDIT repeatedly to display “Erase ?”, then

press ENTER.

2 Press EDIT repeatedly to display “Disc Erase?”,

then press ENTER.

“(track number) Erase OK?” appears in the display.

“Disc Erase OK?” appears in the display.

3 Press ENTER again.

The track is erased and “Complete” appears momentarily.

3 Press ENTER again.

When all audio, name and title data has been erased

“Complete” appears momentarily.

To cancel before erasing the track

Press CANCEL (or &).

To cancel before erasing the entire disc

Press CANCEL (or &).

To undo ERASE

Press & to set this unit to stop mode.

Press EDIT repeatedly to display “Undo Erase”, then

press ENTER.

“Undo OK ?” appears in the display.

Press ENTER again to undo.

To undo ERASE

Press & to set this unit to stop mode.

Press EDIT repeatedly to display “Undo Erase”, then

press ENTER.

To cancel, press CANCEL (or &).

“Undo OK ?” appears in the display.

Press ENTER again to undo.

To cancel, press CANCEL (or &).

Download from Www.Somanuals.com. All Manuals Search And Download.

Part Erase

Disc or Track Title Erase

This operation lets you erase the title of the disc or the title

of tracks on a disc. The title of the disc can only be erased

during the stop mode, however, the title of the track can be

erased during play or stop mode. In the stop mode, use

the jog dial to select the track.

This operation lets you erase part of a track.

2,4 1,2,4

IN ID IS

–5

)

#˜*

To erase a disc title

DIGITAL

REC LEVEL

ANALOG

TIMER

OFF

–

REC LEVEL

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

IN ID IS

–5

CANCEL

)

#˜*

3,5

3,5,6

DIGITAL

REC LEVEL

ANALOG

REC LEVEL

TIMER

OFF

–

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

1 Press #/* to play the track containing the part

you want to erase.

CANCEL

2,3

2 Use SEARCH ! or ⁄ to locate the beginning

of the part you want to erase (point A), then press

#/* to pause at that point.

1 Press & to set this unit to stop mode.

2 Press EDIT repeatedly to display “Title Erase?”,

then press ENTER.

3 Press EDIT repeatedly to display “A–B Erase?”,

“Disc Title” and “Erase OK?” appear alternatively in the

display.

then press ENTER.

Point A (from step 2) is registered and “Erase A–_” appears in

the display.

3 Press ENTER again.

The disc title is erased and “Complete” appears momentarily.

4 Use #/* and SEARCH ⁄ to locate the end of

the part you want to erase (point B).

To erase a track title

5 Press ENTER to register point B.

IN ID IS

–5

“Check” appears momentarily in the display, and two second

segments of the track immediately before point A and after

point B play repeatedly. “Erase A–B?” appears in the display.

)

#˜*

DIGITAL

REC LEVEL

ANALOG

REC LEVEL

TIMER

OFF

–

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

To adjust points A and B

Pressing EDIT repeatedly displays “A point” and “B point”

alternately. Adjust the selected point by turning the jog dial in

the direction you want to move the point.

Each point can be adjusted up to 2 seconds (176 steps) in

either direction.

CANCEL

2,3

1 Turn the jog dial to select the track with the title

you want to erase.

6 Press ENTER again.

2 Press EDIT repeatedly to display “Title Erase?”,

The part is erased and “Complete” appears momentarily.

then press ENTER.

“Track Title” and “Erase OK?” appear alternatively in the

display.

To cancel before erasing the part

Press CANCEL (or &).

3 Press ENTER again.

The track title is erased and “Complete” appears momentarily.

To undo ERASE

To cancel before erasing the disc or track title

Press & to set this unit to stop mode.

Press EDIT repeatedly to display “Undo Erase”, then

press ENTER.

Press CANCEL (or &).

“Undo OK ?” appears in the display.

Press ENTER again to undo.

To cancel, press CANCEL (or &).

To undo ERASE

Press & to set this unit to stop mode.

Press EDIT repeatedly to display “Undo Erase”, then

press ENTER.

“Undo OK ?” appears in the display.

Press ENTER again to undo.

To cancel, press CANCEL (or &).

To erase parts spanning more than one track

Use the COMBINE function described next to combine the

tracks into one track before performing this operation.

Notes

• Note that the DISC and TRACK indicators appear in the

display when “Title Erase” is displayed to distinguish between

the two operations.

• To avoid mistakes when erasing the disc or track names,

press DISPLAY repeatedly until the title display screen

appears so that titles can be confirmed beforehand.

• After part erase, a new track number is automatically

assigned to the section starting after point B.

• Point B cannot be positioned before point A.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMBINE

DIVIDE

This function lets you combine two consecutive tracks into

one. After you combine the tracks, the total number of

tracks decreases by one and the tracks following the

combined tracks are renumbered.

This function lets you divide one track into two separate

tracks by adding a new track number to a certain point in

the track. If you add a track number at the beginning of a

section you want to hear, you can access it quickly by

using the skip function during playback. After you divide a

track, the total number of tracks increases by one and the

tracks following the divided tracks are renumbered.

IN ID IS

–5

)

#˜*

DIGITAL

REC LEVEL

ANALOG

TIMER

OFF

–

REC LEVEL

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

1,2

IN ID IS

–5

CANCEL

3,4

)

#˜*

DIGITAL

REC LEVEL

ANALOG

TIMER

OFF

–

REC LEVEL

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

1 Press & to stop playback.

2 Turn the jog dial to select the second track of the

CANCEL

3,5

two you want to combine.

3 Press EDIT repeatedly to display “Combine ?”,

then press ENTER.

1 Press #/* to play the track you want to divide.

“Check” appears momentarily, then the unit plays the 4

seconds before and after the point where the tracks will be

connected. “(track number) + (track number) OK?” appears in

the display.

2 Use SEARCH ! or ⁄ to locate the point

where you want to divide the track, then press

#/* to pause at that position.

4 Press ENTER again.

The tracks are combined and “Complete” appears

momentarily.

3 Press EDIT repeatedly to display “Divide ?”, then

press ENTER.

“Check” appears momentarily, then “Divide OK ?” appears

and the unit starts repeating the point where the track will be

divided.

To cancel before combining the tracks

Press CANCEL (or &).

4 If necessary, use the jog dial to adjust the

position of the point where the track will be

To undo COMBINE

divided.

The divide position can be adjusted up to 2 seconds (255

steps) in either direction.

Press & to set this unit to stop mode.

Press EDIT repeatedly to display “Undo Combine”,

then press ENTER.

5 Press ENTER.

“Undo OK ?” appears in the display.

The track is divided and “Complete” appears

momentarily.

Press ENTER again to undo.

To cancel, press CANCEL (or &).

Notes

To cancel before dividing the track

• This operation is not possible when track 1 is selected.

• You can also divide the track later using the DIVIDE function.

• If “Can’t Edit” appears in the display, the tracks cannot be

combined. This sometimes happens when you have edited

the same track many times. This is due to the technical

limitations of the MD system and is neither a mechanical error

nor a malfunction.

Press CANCEL (or &).

To undo DIVIDE

Press & to set this unit to stop mode.

Press EDIT repeatedly to display “Undo Divide”, then

press ENTER.

“Undo OK ?” appears in the display.

Press ENTER again to undo.

To cancel, press CANCEL (or &).

Note

You can also combine the tracks later using the COMBINE

function.

Download from Www.Somanuals.com. All Manuals Search And Download.

FRA CHECK

Disc Maintenance

When edit functions such as “MOVE” and “DIVIDE” are

performed, spaces of recordable space may be lost and

“TOC Full” may appear in the display to indicate that no

more recording can be performed. When this occurs, it

may be possible to recover the FRA (Freely Recordable

Area) on the disc that was lost during edit functions so that

more recording is possible.

This unit features two disc maintenance functions which

optimize performance of your MD discs. The TOC WRITE

function allows you to write any edits to the TOC without

having to eject the disc. The FRA CHECK function recovers

recordable space on a disc that may have been lost

because of multiple edit operations. The diagram below

applies to the procedures for both TOC WRITE and FRA

CHECK functions.

1 Press & to stop playback.

2 Press EDIT repeatedly to display “FRA Check ?”,

then press ENTER.

IN ID IS

–5

“FRA Check OK ?” appears.

)

#˜*

DIGITAL

REC LEVEL

ANALOG

TIMER

OFF

–

REC LEVEL

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

3 Press ENTER.

ENTER

“Complete” appears momentarily.

CANCEL

2,3

To cancel before checking the FRA

Press CANCEL (or &).

TOC WRITE

When making a recording, the TOC (Table Of Contents) of

the MD is written as soon as recording is finished. When

making disc edits, however, the TOC isn't automatically

written unless the disc is ejected. If the unit is accidentally

turned off before writing edits to the TOC, it is possible that

these changes will not be saved. By using this function,

you can ensure that your edits are saved on the disc.

1 Press & to stop playback.

2 Press EDIT repeatedly to display “TOC Write ?”,

then press ENTER.

“TOC Write OK ?” appears.

3 Press ENTER.

“TOC Writing” blinks in the display momentarily.

To cancel before writing to the TOC

Press CANCEL (or &).

Notes

• You cannot undo an edit once it has been written to the TOC.

• The TOC Write function can only be selected when the TOC

indicator is lit in the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

TITLING

This function lets you title recorded MDs and the individual

3 Using the front panel

tracks. Titles may consist of uppercase and lowercase

letters, numbers, and symbols for a maximum of up to 250

characters for each title.

Press CHARA. repeatedly to select between

uppercase letters (A), lowercase letters (a), and

numbers (0).

Note : To access the symbols, press CHARA. repeatedly to

select “A”, then turn the jog dial to the left.

! ⁄

DELETE

Using the remote

IN ID IS

–5

Press CHAR. repeatedly to select between uppercase

letters (A) and lowercase letters (a).

#˜*

DIGITAL

REC LEVEL

ANALOG

TIMER

OFF

–

REC LEVEL

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

ENTER

4 Use the jog dial (the character buttons or SKIP

$ or › on the remote) to select a character,

number, or symbol.

2,7 3 5 4

Example (using the remote):

To select “A”, press 1 [ABC] once.

To select “B”, press 1 [ABC] twice.

To select “C”, press 1 [ABC] three times.

To select “1”, press NUMBER, then press 1 [ABC].

5 Press SET to move the cursor into position for the

DISPLAY SCROLL

A–B

REPEAT

(

next character.

–

)

RNDM

PROG

6 Repeat steps 3 through 5 to complete your title.

SPACE

+1 0

To delete a character (ABCD = ABD)

1 Use SEARCH ! or ⁄ to move the cursor to the position

of the character you want to delete.

2 Press DELETE.

2,7

DELETE

TITLE

CHAR. NUMBER DELETE

SET

M-MARK MONO/ ST INPUT

REC

⁄

! ⁄

SKIP

›

TIME

SYNC

To insert a character (ABCD = ABTCD)

1 Use SEARCH ! or ⁄ to move the cursor to the position

where you want to insert the character.

2 Use CHARA. and the jog dial (or CHAR. and the character

buttons on the remote) to select the new character.

3 Press SET to set the character. The character previously in

that position automatically moves to the right.

PLAY

PAUSE

STOP

REC

‹

CD-P

M DX

STOP &

To insert a space (ABCD = AB CD)

1 Use SEARCH ! or ⁄ to move the cursor to the position

where you want to insert the space.

2 Press +10 [SPACE] on the remote.

1 To title a disc

Press & (STOP & on the remote) to stop playback.

7 Press TITLE to exit the title mode.

If a title consists of more than 12 characters, it will scroll

across the display once and then be displayed in abbreviated

form (first 12 characters only).

To title a track

• During stop mode

Use the jog dial (SKIP $ or › on the remote) to select the

track you want to title.

• During playback or pause

To undo TITLE

Use the jog dial (SKIP $ or › on the remote) to select the

track you want to title, or go directly to step 2 to title the

current track.

During playback, the unit automatically repeats the selected

track while you are entering the title.

• During recording

Go directly to step 2 to title the current track.

Recording continues normally while you are entering the title

for the selected track.

Press & (STOP & on the remote) to display the total

tracks and total playing time on the disc.

Press EDIT repeatedly to display “Undo Title”, then

press ENTER.

“Undo OK ?” appears in the display.

Press ENTER again to undo.

To cancel, press CANCEL (or &).

2 Press TITLE to activate the title mode.

The cursor appears in the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER OPERATIONS

With a commercially available audio timer, it is possible to make recordings and initiate playback automatically at any time.

Make sure that all power cord connections between the timer and amplifier/receiver are properly made.

For details, refer to the instructions of your audio timer. No change in any of the other connections between the recorder and

amplifier/receiver, etc., is necessary.

IN ID IS

–5

)

#˜*

DIGITAL

REC LEVEL

ANALOG

TIMER

OFF

–

REC LEVEL

PHONES

LEVEL

›

REC

PLAY

RANDOM S/

REPEAT A–B DISPLAY SCROLL

TITLE

CHARA. DELETE

CANCEL

EDIT

SET

⁄

INPUT

TIMER

ENTER

To AC outlet

Amplifier

Audio timer

Tuner

Timer Recording

Timer Playback

1 Turn on the power of each component, then set

1 Turn on the amplifier/receiver and adjust the

your tuner to the station you want to record.

volume and tone controls.

2 Set this unit’s recording options.

2 Set the input mode selector of your amplifier/

Select digital or analog inputs, auto or manual marking,

and stereo or mono recording. When recording analog

signals, be sure to set the recording level. When

recording digital signals, the recording level is set at

0 dB. (See pages 13 to 16 for details regarding these

operations.)

receiver to MD.

3 Set the timer to the times at which you want to

start and stop playback.

4 Set TIMER to PLAY.

TIMER

OFF

3 Turn down the volume on your amplifier/receiver.

REC

PLAY

This has no effect on the recording level.

4 Set the timer to the times at which you want to

start and stop recording.

We recommend setting the timer to start a few minutes before

and stop a few minutes after the actual broadcast to leave

some room for later editing.

When the preset time arrives, the timer turns on the

components (amplifier/receiver and MD recorder) and

the MD recorder starts to play. When the stop time

arrives, the timer stops the playback by turning off the

components.

5 Set TIMER to REC.

TIMER

OFF

Notes

REC

PLAY

• Playback always starts from the beginning of the MD.

• Set TIMER to OFF when not using the timer play function. If

the power is turned on (by pressing POWER, plugging in the

power cord, etc.) when TIMER is set to PLAY, the MD

recorder will start to play and may cause a sudden output at

high volume.

When the preset time arrives, the timer turns on the

components (amplifier/receiver, tuner and MD

recorder) and the MD recorder starts to record. When

the stop time arrives, the timer stops the recording by

turning off the components.

Notes

• When recording to a blank MD, recording starts from the

beginning. When recording to a previously recorded MD,

recording starts from the end of the last track.

• Set TIMER to OFF when not using the timer recording

function. If the power is turned on (by pressing POWER,

plugging in the power cord, etc.) when TIMER is set to REC,

the MD recorder will start recording automatically.

Download from Www.Somanuals.com. All Manuals Search And Download.

MD SYSTEM LIMITATIONS

The recording system in your MD recorder is radically

Tracks created through editing may exhibit sound

dropout during search operations.

different from those used in cassette and DAT decks and is

characterized by the limitations described below. Note,

however, that these limitations are inherent to the MD

recording system and are not a result of mechanical

trouble.

Track numbers are not recorded correctly

Incorrect assignment or recording of track numbers may

result when CD tracks are divided into several smaller

tracks during digital recording.

“Can’t REC” is displayed before the maximum

recording time (60 or 74 minutes) has been reached

It is not possible to erase part of a track using the A-B

ERASE function

Once 255 tracks have been recorded on one MD, “Can’t

REC” is displayed regardless of the total recorded time.

More than 255 tracks cannot be recorded on one MD. To

continue recording, erase unnecessary tracks, combine

tracks to reduce the total number of tracks, or use another

recordable MD.

This unit organizes the audio data in sound groups and

clusters. The minimum size of these units varies according

to the number of channels being recorded. For a 2 channel

(stereo) recording, a single unit may not consist of less

than 10 seconds of sound. For one channel (mono)

recording, a single unit may not consist of less than 20

seconds of sound.

“Disc Full” is displayed before the maximum number of

tracks (255) have been recorded

During automatic track marking, fluctuations in emphasis

within songs may be interpreted as song intervals,

increasing the total number of tracks and causing “Disc

Full” to be displayed.

Limitations when recording over an existing track

• The correct remaining recording time may not be

displayed.

• You may find it impossible to record over a track if that

track has been recorded over several times already. If

this happens, erase the track using the ERASE function.

• The remaining recording time may be shortened out of

proportion to the total recorded time.

• Recording over a track to eliminate noise is not

recommended since this may shorten the duration of the

track.

The remaining recording time does not increase even

after erasing numerous short tracks

Tracks under 12 seconds in length are not counted and so

erasing them may not lead to an increase in the recording

time.

• You may find it impossible to label a track while

recording over another track.

“TOC Reading” is displayed continuously

The “TOC Reading” display lasts longer than normal when

a brand new (blank) disc is inserted.

The correct recorded/playing time may not be displayed

during playback of MDs recorded in monaural.

The total recorded time and the remaining time on the

MD do not total to the maximum recording time

• Recording is done in minimum units of 2 seconds each,

no matter how short the material. The contents recorded

may thus be shorter than the maximum recording

capacity. Disc space may also be further reduced by

scratches.

• This unit displays the length of the largest continuous

blank area as the remaining time. Therefore, if there are

several separate blank spaces, the remaining time will

only display a time equivalent to the largest continuous

blank space.

If there is a 1 minute blank space and a 2 minute blank

space, the remaining time display will be “2” minutes. If

you then record 1 minute and 30 seconds of the 2 minute

blank, the remaining time display will become “1” minute.

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES REGARDING THE

REMOTE CONTROL

COPY PROTECTION (SCMS)

As a digital audio component, this MD recorder conforms

with the Serial Copy Management System (SCMS)

standards. The Serial Copy Management System restricts

copies made by recording digital signals to first-generation

copies only. Therefore, an MD recorded through a digital

input cannot be used as a source for making another

digital recording.

Remote Control Operation Range

However, subsequent recordings can be made from the

first-generation copy by using the analog input/output

jacks.

6 m

There are three general rules that apply to this unit.

30°

Rule 1

You can record from digital program sources (CDs, DATs

or pre-mastered MDs) onto a DAT tape or recordable MD

via the digital input jack on a DAT or MD recorder. You

cannot, however, record from this recorded DAT tape or

MD to another DAT tape or recordable MD via a digital

input jack.

Notes

• There should be no large obstacles between the remote

control and the remote sensor on the main unit.

• Strong light (especially from an inverter type fluorescent lamp)

shining directly on the remote sensor may prevent proper

operation. In such cases, reposition the main unit to avoid

direct light.

Rule 2

You can record a digital signal input from a digital satellite

broadcast onto a DAT tape or recordable MD via the digital

input jack on the DAT or MD recorder. (This unit is

equipped with a sampling rate converter that allows you to

make digital recordings from 32 kHz, 44.1 kHz, or 48 kHz

digital program sources).

Battery Installation

If the broadcast does not contain a copyright protection

code, you can then record the contents of this recorded

DAT tape or MD (first-generation) onto another DAT tape or

recordable MD via a digital input jack on the DAT or MD

recorder to create a second generation digital copy (these

copies may also be copied digitally). Note, however, that if

the broadcast contains a copy protection code, second-

generation digital copying will not be possible.

Rule 3

You can record a DAT tape or MD recorded via the DAT or

MD recorder’s analog input jack onto another DAT tape or

MD via the DAT or MD recorder’s digital output jack. You

cannot, however, make a second-generation DAT tape or

MD copy via the DAT or MD recorder’s digital output jack.

Battery replacement

When you notice a decrease in the operating range of the

remote control, replace both batteries with new ones.

Notes

• Use only AA, R6, UM-3 batteries for replacement.

• Be sure to insert the batteries with correct polarity (as

illustrated on the battery compartment).

• Remove the batteries if the remote control will not be used for

an extended period of time.

• If batteries leak, dispose of them immediately. Avoid touching

the leaking material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly

before installing new batteries.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

If your MD recorder fails to operate normally, check the following table. It lists common operating errors and simple

measures which you can take to correct the problem. If it cannot be corrected, or the symptom is not listed, disconnect the

recorder’s power cord and contact your authorized YAMAHA dealer or service center for help.

Symptom

Cause

Remedy

The unit does not respond to

operations.

• MD is dirty or damaged.

• MD is damaged (“UTOC ERR appears

in the display).

• Replace the current disc with a new

one.

It happens that this unit does not work

normally.

• There is an influence of strong external

noise (lightning, excessive static

electricity, etc.) or a misoperation was

performed while using this unit.

• Turn the power off and disconnect the

AC power from the AC outlet. After

about 30 seconds have passed,

connect the power and try again.

Playback is not possible.

• Moisture is on the laser pickup.

• Leave the unit switched ON and wait 20

to 30 minutes for the moisture to

evaporate before trying to play a disc.

• Press POWER to turn the power on.

• Reload the disc with the label side

facing up, and the arrow pointing

toward the disc insertion slot.

• The power is OFF.

• The disc has been loaded incorrectly.

• An unrecorded (blank) MD was loaded

(“Blank Disc” appears in the display) .

• Insert a recorded MD.

Recording is not possible.

• The disc is record protected

(“Protected” appears in the display).

• A pre-mastered MD is loaded

• Slide the record-protect tab to the

closed position.

• Load a recordable MD.

(“Playback MD” appears in the display).

• The source is not connected correctly.

• The input setting is incorrect.

• Check all connections again.

• Press INPUT repeatedly to select the

correct input jacks.

• The recording level is too low.

• Turn REC LEVEL to adjust the recording

level.

• The digital output level of the digital

source is too low.

• Set the digital output level of the digital

source to “MAX”.

• There is not enough blank space left on

the MD.

• Load a recordable MD with fewer

recorded tracks, or erase unnecessary

tracks from the current MD.

• If recording was interrupted, try

recording again starting from the

beginning.

• If the power cord was unplugged or

there was a power outage during

recording, that recording may be lost.

The MD cannot be removed when

partially inserted.

• The carriage lock function has activated.

• Insert the MD completely, then press

) EJECT to eject it.

Excessive noise.

• The unit is too close to the television or

other component.

• Place the unit farther away from the

television or other component.

The remote control does not operate.

• The batteries are exhausted.

• The remote control transmitter is

operated from an incorrect distance or

angle.

• Replace the batteries.

• Operate the remote from less than 6

meters (about 20 feet) and within 30° on

either side of the sensor.

• The remote control sensor is located in

strong direct light.

• Place the unit away from the strong

light.

To clean the cabinet

Use a soft cloth slightly moistened with mild detergent solution.

Care of MDs

• Do not expose the MD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight

as there can be a considerable rise in temperature inside the car.

• Periodically remove dust and debris from the cartridge surface by wiping it with a dry cloth.

• Because the MD itself is housed in a cartridge, you can handle it normally without being concerned about dirt or

fingerprints. However, malfunctioning may result if the cartridge itself is dirty or warped.

Do not open the shutter on the MD cartridge

Trying to force the shutter open will damage the shutter.

Download from Www.Somanuals.com. All Manuals Search And Download.

TMP Over!!

DISPLAY MESSAGES

The temperature of the unit has exceeded the normal

operating temperature. Turn off the unit and let it cool

down. If the unit is installed in a place with little ventilation

(such as a built in bookcase), move the unit to another

location with better ventilation.

Can’t Copy

Digital recording cannot be performed. (See “COPY

PROTECTION (SCMS)” on page 26.)

TOC Writing

Can’t Edit

The TOC data is being written to the disc. Do not move the

unit or pull out the mains lead. If you do, recorded material

may not be saved normally.

Edit operations are not possible.

Can’t Play!

Timer playback is not possible. The loaded disc may be

blank, damaged, or an incompatible format.

TOC Reading

The unit is reading the TOC data.

Can’t REC!

Protected

Timer recording is not possible. The loaded disc may be

protected or there may not be enough blank space

remaining on the disc.

The record protection on the inserted MD is set to

“protect”.

Playback MD

Can’t REC

The inserted MD is a designed for playback only (you

cannot record on this disc).

Recording is not possible because there is not enough

blank space remaining on the disc.

MONITOR OUT

DIGin Unlock

The monitor out function is active. The audio signal input to

the selected input terminals is output from this unit’s output

terminals.

No digital signal is being input to the selected digital input

jack.

Disc Full

Recording is not possible because there is no blank space

remaining on the disc.

Program Full

Additional steps cannot be programmed because the

maximum number of steps (30) has already been

programmed.

Title Full

Additional characters cannot be input for the current title

because the maximum number of characters for a single

title (250) has already been input.

UTOC WError

Error occurred when writing to the UTOC.

Not Audio

The inserted disc is not an audio MD.

Tr Protected

The selected track cannot be edited because it is

protected.

TOC Full

The disc area allotted for TOC data has become full and

further editing is not possible.

UTOC ERR L...

Problem involving UTOC data.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

Digital audio system

Inputs

System

LINE IN (REC)

MiniDisc digital audio system

Disc

Type: pin jack

Standard input level (56 k-ohms): 300 mV

DIGITAL IN (OPTICAL) (2)

Type: square optical connector jack

Mini Disc

Recording method

Magnetic field variation overwrite

Reading method

Non-contact optical pickup (using semiconductor

laser)

Outputs

LINE OUT (REC)

Type: pin jack

Standard output level (1 kHz, 0 dB): 2.0 ± 0.5 Vrms

DIGITAL OUT (OPTICAL)

Type: square optical connector jack

PHONES

Laser

Semiconductor laser

Laser Diode Properties

Material: GaAIAs

Wavelength: 780 nm

Pulse time:

...

Standard output level

(Input 150 ohms shorted, –20 dB): 300 ± 60 mV

Read mode 0.8 mW Continuous

...

Write mode

max 10 mW 0.5S

min cycle 1.5S

Repetition

GENERAL

Record/playback time

Max. 74 minutes (using MDW-74 disc)

74 minutes (stereo)

148 minutes (mono)

Power Supplies

230 V, 50 Hz (U.K. and Europe models)

120 V, 60 Hz (U.S.A. model)

Power Consumption

Revolutions

Approx. 400 – 900 rpm (CLV)

Error Correction

ACIRC (Advanced Cross Interleave Reed-solomon

Code)

Sampling frequency

44.1 kHz (32 kHz and 48 kHz signals converted to

44.1 kHz for recording)

Coding

ATRAC (Adaptive TRansform Acoustic Coding)

Modulation system

EFM (Eight-to-Fourteen Modulation)

Number of channels

20 W

Dimensions (W x H x D)

435 x 96 x 288 mm (17-1/8" x 3-3/4" x 11-5/16")

Weight

4.1 kg (9 lbs. 1 oz.)

Accessories

Remote Control

Audio connecting cord

Optical fiber cable

Batteries (size AA, R6, UM-3)

2 (stereo) or 1 (monaural, for extended recording)

Frequency Response

5 – 20,000 Hz ±0.5 dB

Signal-to-Noise Ratio

More than 99 dB during playback

Wow and Flutter

Specifications subject to change without notice.

Below measurable limit

Download from Www.Somanuals.com. All Manuals Search And Download.

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B.

WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia

V354880

Download from Www.Somanuals.com. All Manuals Search And Download.

Weslo Home Gym 831,21611,0 User Manual
Weslo Treadmill WLTL39093 User Manual
Whirlpool Oven AKZ 561 User Manual
Whirlpool Ventilation Hood IN600S User Manual
Wolf Appliance Company Ventilation Hood PW302210R User Manual
Worksaver Lawn Mower FM 560, FM 572 User Manual
Yamaha Home Theater Server MCX 2000 User Manual
Zanussi Oven FM 55 User Manual
Zanussi Refrigerator Z1142TRM User Manual
Zanussi Washer FL 816 A User Manual