This Manual is Bookmarked
Operating Instructions — Parts Manual
Square Wheel Belt Grinder
Models: 4103, 4106, and 4126AC
WHM TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123
Ph.: 800-274-6848
Part No. 5507796
Revision C2 09/04
Copyright © WMH Tool Group
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Cover Page .........................................................................................................................................1
General Specifications .........................................................................................................................4
Operating Precautions .........................................................................................................................5
Setup and Operation............................................................................................................................7
Maintenance ......................................................................................................................................10
Wiring Diagrams ................................................................................................................................12
Replacement Parts ............................................................................................................................13
Troubleshooting .................................................................................................................................13
Accessories .......................................................................................................................................17
3
Download from Www.Somanuals.com. All Manuals Search And Download.
General Specifications
The Wilton Square Wheel Belt Grinder,
Models 4103, 4106 and 4126AC, are
designed for grinding, deburring,
chamfering, and internal/external grinding of
small and large parts. The Square Wheel
Belt Grinder can be used to polish or buff
finished parts and grind small internal radii
using available accessories. Accessory
changeover is quick and easy. Belt tension
and tracking are easily adjustable.
The Square Wheel Belt Grinder is available
in either single speed (Models 4103 and
4106) or variable speed model (Model
4126AC). The variable speed model is
controlled by an inverter that provides belt
speeds ranging from 0 to 6000 SFPM.
4
Specifications
Belt Width & Length
Belt Speed
Model 4103
2 x 72 Inches
4600 SFPM
Model 4106
2 x 72 Inches
4600 SFPM
Model 4126AC
2 x 72 inches
0 - 6000 SFPM
1 HP, 1,750 rpm
Motor
1 HP, Single Phase, 2 HP, Three Phase,
1750 rpm 1750 rpm
Contact Wheel Diameters
Weight
1-1/2, 3, & 8 inches 1-1/2, 3, & 8 inches
115-125 pounds 120 pounds
1-1/2, 3, & 8 inches
120 pounds
Download from Www.Somanuals.com. All Manuals Search And Download.
- Never leave machine running while you are away
from it.
- Always shut off the machine when not in use.
When servicing machine:
- Always unplug machine from electrical power while
servicing.
- Misuse of this machine can cause serious injury.
- For safety, machine must be set up, used and
serviced properly.
- Read, understand and follow instructions in the
operator’s and parts manual which was shipped with
your machine.
- Always follow instructions in operators and parts
manual when changing accessory tools or parts.
- Never modify the machine without consulting Wilton
Corporation.
When setting up machine:
- Always avoid using machine in damp or poorly
lighted work areas.
- Always be sure machine is securely anchored to
the floor.
- Always keep machine guards in place.
- Always put start switch in OFF position before
plugging in machine.
You — the stationary power tool user—
hold the key to safety.
Read and follow these simple rules for best results
and full benefits from your machine. Used properly,
Wilton’s machinery is among the best in design and
safety. However, any machine used improperly can
be rendered inefficient and unsafe. It is absolutely
mandatory that those who use our products be
properly trained in how to use them correctly. They
should read and understand the Operators and Parts
Manual as well as all labels affixed to the machine.
Failure in following all of these warnings can cause
serious injuries.
When using machine:
- Never operate with machine guards missing.
- Always wear safety glasses with side shields (See
ANSI Z87.1)
- Never wear loose clothing or jewelry.
- Never overreach
machine.
you may slip and fall into the
Machinery general safety warnings
1. Always wear protective eye wear when operating
machinery. Eye wear shall be impact resistant,
protective safety glasses with side shields which
comply with ANSI Z87.1 specifications. Use of
eye wear which does not comply with ANSI Z87.1
specifications could result in severe injury from
breakage of eye protection.
2. Wear proper apparel. No loose clothing or
jewelry which can get caught in moving parts.
Rubber soled footwear is recommended for best
footing.
8. Disconnect electrical power before servicing.
Whenever changing accessories or general
maintenance is done on the machine, electrical
power to the machine must be disconnected
before work is done.
9. Maintain all machine tools with care. Follow all
maintenance instructions for lubricating and the
changing of accessories. No attempt shall be
made to modify or have makeshift repairs done to
the machine. This not only voids the warranty but
also renders the machine unsafe.
5
3. Do not overreach. Failure to maintain proper
working position can cause you to fall into the
machine or cause your clothing to get caught
pulling you into the machine.
4. Keep guards in place and in proper working
order. Do not operate the machine with guards
removed.
5. Avoid dangerous working environments. Do not
use stationary machine tools in wet or damp
locations. Keep work areas clean and well lit.
6. Avoid accidental starts by being sure the start
switch is OFF before plugging in the machine.
7. Never leave the machine running while unattended.
Machine shall be shut off whenever it is not in
operation.
10. Machinery must be anchored to the floor.
11. Secure work. Use clamps or a vise to hold work,
when practical. It is safer than using your hands
and it frees both hands to operate the machine.
12. Never brush away chips while the machine is in
operation.
13. Keep work area clean. Cluttered areas invite
accidents.
14. Remove adjusting keys and wrenches before
turning machine on.
15. Use the right tool. Don’t force a tool or attachment
to do a job it was not designed for.
16. Use only recommended accessories and follow
manufacturers instructions pertaining to them.
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Keep hands in sight and clear of all moving parts
and cutting surfaces.
safe by using padlocks, master switches, or by
removing starter keys.
18. All visitors should be kept at a safe distance
from the work area. Make workshop completely
19. Know the tool you are using—its application,
limitations, and potential hazards.
Wire sizes
Caution: for circuits which are far away from the
electrical service box, the wire size must be in-
creased in order to deliver ample voltage to the
motor. To minimize power losses and to prevent
motor overheating and burnout, the use of wire sizes
for branch circuits or electrical extension cords
according to the following table is recommended:
General Electrical Cautions
This machine should be grounded in accordance with
the National Electrical Code and local codes and
ordinances. This work should be done by a qualified
electrician. The machine should be grounded to
protect the user from electrical shock.
AWG (American wire gauge) Number
Conductor Length
240 Volt Lines
120 Volt Lines
0 - 50 Feet
50 - 100 Feet
Over 100 Feet
No. 14
No. 14
No. 14
No. 14
No. 12
No. 8
Safety requirements for abrasive grinding machines
condition. If the disc is not operating accurately
Abrasive grinding can be hazardous to operators and
bystanders. Grinding sparks, chips and dust par-
ticles thrown off by the grinding disc can cause
serious injury by contact or inhalation. To avoid
such injuries you must comply with the following
safety requirements:
1. Always wear protective eyewear when operating
machinery. Eye wear shall be impact resistant,
protective safety glasses with side shields which
and smoothly, immediately stop the motor and
make repairs before attempting any grinding
operations.
7. Abrasive discs must be stored in a controlled
environment area. Relative humidity should be
35% to 50% and the temperature should be
between 60 and 80 degrees Fahrenheit. Failure
to do so could cause premature disc failure.
comply with ANSI Z87.1. Use of eye wear which 8. Examine the face of the grinding disc carefully.
does not comply with ANSI Z87.1 specifications
could result in severe injury from breakage of
eye protection. See Figure A, below.
Excessive grinding which wears down to the
backing material can tear the disc. Never use a
disc which shows backing, nicks or cuts on the
surface or edge or damage due to creasing or
poor handling.
2. Wear leather safety gloves, arm guards, leather
aprons and safety shoes.
3. A dust collection system is recommended,
Operator shall also wear a dust mask at all
times. See Figure B, below.
4. Additional precautions may be necessary for
grinding materials which are flammable or have
other hazardous properties. You should always
consult the manufacturer of such materials for
instructions on grinding and handling.
5. Do not force or jamb the workpiece into the
grinding disc.
9. When installing a new disc, be certain the disc is
accurately centered on the drive wheel. Failure
to do so could cause a serious unbalanced
condition.
10. Always present the workpiece to the wheel while
resting the workpiece firmly on the table. Failure
to do so could result in damage to the workpiece
or throwing of the workpiece off the wheel.
11. Safety shoes which comply with ANSI Z41.1 shall
be worn. See Figure C.
6
6. Before grinding, always allow the motor to come 12. Personal hearing protection such as ear plugs or
up to operating speed, then check the grinding
disc for wobble, runout, or any unbalanced
ear muffs shall be used to protect against the
effect of noise exposure. See Figure D:
A
B
C
D
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This manual includes operating and maintenance instructions for the Wilton Model 4103, 4106 and 4126AC
Square Wheel Belt Grinder. The manual also includes parts listings and illustrations of replaceable parts.
Refer to Figures 1 and 2 for key features of the Square Wheel Belt Grinder.
Setup and Operation
The Square Wheel Belt Grinder can be mounted on a work bench or an optional pedestal. The grinder should
be secured to the work bench or pedestal using the four holes in the base of the grinder. (Refer to Assembly
of Pedestal for machines that are to be pedestal-mounted.)
Installation of Work Rest
The work rest mounts on the left side of the head casting. Attach the work rest using the socket head cap
screw provided with the machine.
The slot in the work rest has a lip against which the cap screw is tightened. Place the hole at the end of the slot
over the cap screw. Then slide the rest inward until the work rest is in position in front of the contact wheel.
Tighten the cap screw.
Belt Tension Lever
Motor
Belt Tracking
Adjustment
Inverter
Belt Tracking
Adjustment
Upper
Guard
Upper
Guard
ON/OFF
Switch
Motor
7
Work
Rest
Switch
Work
Rest
Contact
Wheel
Contact
Wheel
Pedestal
Pedestal
Figure 1: Square Wheel Grinder Features
(single speed)
Figure 2: Square Wheel Grinder Features
(variable speed)
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Controls
Model 4103/4106
Vacuum Connection
NOTE:
A variety of vacuum system options
The ON/OFF switch for the Model 4103/4106 grinder
is located in a switch box mounted on the drive
motor.
are available. (Refer to Accessories section.)
The grinder uses a front mounted vacuum system.
Refer to Fgure 3. Install the vacuum system
components as follows:
1. Slide the support bracket into the channel
secured to belt grinder base. Install one knob
in the belt grinder base to secure the support
bracket.
Model 4126AC
NOTE: Refer to Figure 4. Use only the inverter
controls defined in the following procedures. The
inverter is pre-programmed at the factory and
requires no further programming.The controls for
the Model 4126AC grinder are located on the
inverter. The ON/OFF switch is located on the left
side of the inverter. Start the grinder by setting the
ON/OFF switch to ON.
NOTE: Refer to vacuum scoop exploded view,
Figure 11 when installing channel.
2. Slide the ducted scoop onto the support
bracket. Install remaining knob in the support
bracket to secure the scoop.
3. Connect hose to exhaust duct and secure with
a clamp.
Press the FWD RUN pushbutton on the inverter
and set the speed using the up/down arrow keys
(to the right of the speed display). Press the up
arrow to increase speed; press the down arrow to
reduce speed. The display on the inverter shows
drive motor speed in revolutions per minute. Press
the STOP button on the inverter to stop the grinder.
Then set the ON/OFF switch to OFF.
STOP
Button
Up
FWD (For-
ward) Button
Down
On/Off
Switch
Speed Display
(RPM)
8
Clamping
Knob
Support
Bracket
Scoop
Clamping
Knob
Figure 4: Operating Controls
(Model 4126AC)
Figure 3: Vacuum Connection
Electrical Connection
Refer to the Wiring Diagram section for wiring
information. Connection to electrical power should
be made by a qualified electrician. Observe local
electrical codes when connecting the machine.
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Uses for the Square Wheel Belt Grinder
Flat or angular
stock — Platen
Contouring — Grind
difficult, hard to
reach areas with the
3-inch by 2-inch or 1-
1/2 inch by 2-inch
diameter contact
wheels. Contours
and shapes unique
parts like propellers
and metal furniture.
Shaping — For
grinding and finish-
ing cylindrical
Roughing — Ser-
rated contact wheel is
used for removing
heavy stock, cleaning
up a weld or snag-
ging a casting. This
durable 8-inch
diameter wheel is
used extensively for
hollow grinding and
profiling knives and
other culinary tools.
It is standard equip-
ment on all models.
setting is the perfect
angle for high speed,
precision, flat and
level grinding of
tools, knives, plas-
tics, and other
materials. The platen
allows working to
very close toler-
ances. An adjustable
work rest is standard
on all models.
shapes. The yoke
surface conforms to
the shape of the
surface to produce
an even, smooth
finish without the
danger of scarring.
Excellent for tool
post applications.
OPTIONAL FEATURES
9
Internal contouring
— The air-cushioned
dead head is for use
on very small radius
grinding. When
Internal contouring with
small wheel — This small
wheel accessory is
designed for hard to reach
places. Includes 5/8-inch,
70 durometer contact
wheel. Available contact
wheels are 1/2-inch, 3/4-
inch, and 1-inch.
Polishing — The
Finishing — The nylon
reinforced, silicone
carbide wheel is
perfect for polishing
and deburring. It
buffing pad is perfect
for satin finish or high
gloss polishing. The
fine, close stitched
burring pads are ideal applies a high luster
for metal and plastic
connected to a
source of shop air
(80-90 psi), the belt
rides on a cushion of
air to decrease head
and belt wear. The
dead head is easy to
use, and adapts to
any of the available
radius tips.
finish on rough sur-
faces and is excellent
for steel, iron, or
aluminum.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation of Platen
WARNING: BE SURE TO SET ON/OFF SWITCH
OFF TOAVOID PERSONAL INJURY.
1. Refer to Figure 6. Lower the tension lever to
release belt tension.
2. Loosen upper guard knob and swing guard
back for clearance.
3. Loosen the contact wheel shaft clamping screw
on the head casting.
Maintenance
Cleaning
Shutoff the machine before cleaning. Keep the exterior
of the machine clean and free of chips. Use a brush for
cleaning. Periodically empty grinding dust and particles
from the dust collection system.
Lubrication
Lubrication of the grinder is not required. The drive
motor and contact wheel are fitted with sealed bearings.
4. Remove contact wheel (see Replacement of
Contact Wheel).
5. Install pivot shaft of platen in head casting.
Position platen as desired.
A. For grinding flat or angular work
pieces, position the platen with the platen
surface facing outward.
Replacement of Contact Wheel
WARNING: BE SURE TO SET ON/OFF SWITCH TO
OFF TOAVOID PERSONALINJURY.
1. Refer to Figure 5. Lower the tension lever to release
belt tension.
2. Loosen upper guard knob and swing guard back for
clearance.
3. Loosen the contact wheel shaft clamping screw on
the head casting.
4. Remove the contact wheel assembly.
5. Remove retaining rings from wheel shaft.
6. Remove shaft and wheel bearings.
7. Install bearings in replacement contact wheel.
8. Install shaft and secure with retaining rings.
9. Install contact wheel shaft in head casting.
10. Tighten clamping screw.
B. For grinding of cylindrical work pieces,
position the platen with the “yoke” side
facing outward.
C. Set at desired angle.
6. Tighten clamping screw.
7. Lift tension lever to set belt tension.
8. Lower and adjust position of upper guard.
Tighten the upper guard knob.
Platen
11. Lift tension lever to set belt tension.
12. Lower and adjust position of upper guard. Tighten
the upper guard knob.
Clamping
Screw
Pivot
Shaft
Tension
Lever
Upper Guard
10
Upper Guard Knob
Clamping
Screw
Work
Rest
Contact
Wheel
Figure 6: Installation of Platen
Head
Casting
Figure 5: Replacement of Contact Wheel
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Spin the drive wheel by hand and check track-
ing of the belt. If the belt tracks either right or
left, adjustment is required.
3. Use an Allen wrench to change the alignment
of the idler wheel. Turn the idler adjustment
screw clockwise to cause the belt to track right.
Turn the idler adjustment screw counterclock-
wise to cause the belt to track left.
Replacement of Grinding Belt
WARNING: DO NOT OPERATE THE MACHINE WITH
THE SIDE PANELOPEN. DISCONNECT ELECTRI-
CAL POWER TO THE MACHINE BEFORE PERFORM-
ING ANY MAINTENANCE.
1. Refer to Figure 7. Lower the belt tension lever to
release tension on the belt.
2. Loosen the knob on the left side of the machine
and raise upper guard. Turn the knob on the side
panel and lower the side panel.
3. If required, loosen work rest to provide clearance
for belt removal.
4. Remove the belt from the drive wheel, idler
wheel, and contact wheel. Install the replace-
ment belt over the drive wheel, idler wheel, and
contact wheel.
5. Raise the belt tension lever to tighten the belt
against the wheels. Tighten the belt until it is just
taut. A moderate tension will provide faster
cutting, longer belt life, and better tracking. Do
not over-tension the belt.
4. Close side panel and secure by turning the
knob on the panel. Lower the upper belt guard
and secure with the knob on the left side of the
grinder.
5. Connect electrical power and start the grinder.
Check belt tracking (the belt should be cen-
tered on the contact wheel.
6. If required, adjust belt tracking to center the
belt on the contact wheel. Turn the idler
adjustment screw clockwise to move the belt to
the right. Turn the idler adjustment screw
counterclockwise to move the belt to the left.
7. If the belt does not track properly, increase belt
tension. Repeat steps 1 through 6.
6. Check belt tracking by spinning the drive wheel
by hand. Adjust tracking if required. (Refer to
Checking Belt Tracking.)
Replacement of Inverter
Upper
Guard
Idler Wheel
Grinding
Belt
WARNING: DISCONNECT ELECTRICAL POWER
TO THE MACHINE BEFORE PERFORMING ANY
MAINTENANCE.
1. Disconnect electrical power.
2. Remove access panel on front of inverter.
Disconnect inverter wiring.
3. Remove four screws (1) and four nuts (6) from
inverter (2). Separate inverter (2) from mount
(4).
Drive
Wheel
11
Contact
Wheel
4. Install replacement inverter (2) and secure with
four screws (1) and four nuts (6).
5. Connect electrical wiring (refer to Wiring
Diagram section for connections).
6. Start belt grinder and check for proper opera-
tion.
Side
Panel
Figure 7: Replacement of Grinding Belt
NOTE: Inverter is pre-programmed at the factory,
further programming is not required.
Checking Belt Tracking
WARNING: DO NOT OPERATE THE MACHINE WITH
THE SIDE PANELOPEN. DISCONNECT ELECTRI-
CAL POWER TO THE MACHINE BEFORE PERFORM-
ING ANY MAINTENANCE.
1. Loosen the knob on the left side of the machine
and raise upper guard. Turn the knob on the side
panel and lower the side panel.
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagrams
Model 4103
12
Model 4106
Model 4126AC
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Probable Cause
Suggested Remedy
Poor Tracking
1. Improper belt splice.
2. Excessive belt tension.
3. Insufficient belt tension.
4. Worn contact surfaces.
1. Check belt for irregular seam or shape.
2. Set tension so belt is just taut.
3. Set tension so belt is just taut.
4. Check elastomer on contact wheels.
Replace worn wheels.
5. Misaligned contact surfaces.
5. Check alignment of drive wheel and
contact wheels. The drive pulley and
contact wheel must be aligned. To
adjust drive wheel, loosen set screws
and move drive wheel in or out on
motor shaft as required. To adjust
contact wheel, loosen shaft clamping
screw and move contact wheel in or out
as required.
6. Lack of crown on drive wheel.
7. Worn bearings.
6. Check for 1/16-inch crown. Replace
drive wheel if crown is not present.
7. Check all bearings for overheating or
damage. Replace worn or damaged
bearings.
Slack Belt
1. Insufficient belt tension.
1. Set tension so belt is just taut.
Contact Wheel Wear
1. Excessive belt tension.
2. Grinding in one area on belt.
1. Set tension so belt is just taut.
2. Use entire work surface of belt when
ever possible.
3. Excessive grinding deposits
on belt and debris in machine.
3. Periodically clean interior of grinder.
Short Belt Life
1. Excessive grinding pressure.
1. Allow the belt to do the cutting.
Excessive pressure dulls the belt and
removes the grit from the belt.
13
Replacement Parts
This section provides exploded view illustrations that show the replacement parts for the Wilton Models 4103,
4106 and 4126AC Square Wheel Belt Grinder. Also provided are parts listings that show part number, descrip-
tion and quantity. The item numbers on the illustration relate to the item number in the facing page of the parts
listing.
Order replacement parts from:
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123
Phone: 800-274-6848
Identify the replacement part by the part number shown in the parts listing. Be sure to include the model
number and serial number of your machine when ordering replacement parts to assure that you will receive the
correct part.
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View - Square Wheel Belt Grinder
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Ref. Part
No. Number
Parts List - Square Wheel Belt Grinder
Ref. Part
Description
Qty.
1
1
1
1
1
1
1
1
4
1
1
2
1
2
1
1
2
1
1
1
1
1
1
1
30
31
5541241
5644231
9066821
Switch (Model 4103 only)
Manual Motor Starter (Model 4106 only)
No. Number
Description
Qty.
1
5510944
5510943
5510942
5044590
5044610
Contact Wheel
Assy, 10 x 2 Serrat, 90 Duro
1
1
1
1
1
2
1
2
2
2
1
1
1
1
1
Motor & Switch, 1 HP
,
Cont
act Wheel Assy
, 8 x 2 Smooth, 50 Duro
, 8 x 2 Serrated, 50 Duro
Assy, 1-1/2 x 2
Assy, 3 x 2
Single Phase (Model 4103)
Motor, 2 HP, 3 Phase (Model 4106)
Motor, 1 HP, 3-Phase (Model 4126AC only)
Knob, Hand
Nut, Allen, 5/16-18
Bolt, Hex Head, w/Nylock 3/8-16 x 3/4
Key, 3/16 x 3/16 x 1-1/4
Pulley, Drive
Set Screw, Socket Head 5/16-18 x 1/2
Screw, Socket Head Hex 5/16-18 x 1-1/2
Cont
act Wheel Assy
9066831
5508076
9070361
9070781
9128671
9114320
5044511
9054541
5630451
5077041
9070381
5630061
5507583
5055311
9070371
5044630
9057461
5046600
5046540
5541030
2
3
Contact Wheel
Contact Wheel
Screw, Flat Head Cap
Idler Wheel
Bearing
Retaining Ring, Internal
Retaining Ring, External
Contact Wheel, 8 x 2 Serrated, 50 Duro
Contact Wheel, 8 x 2 Smooth, 50 Duro
Contact Wheel, 10 x 2 Serrated, 90 Duro
Shaft, 8 x 10 Wheel
Retaining Ring, External
Abrasive Belt, 2 x 72, 50 Grit (S
tandard -
optional grit below) (10 piece minimum order)
Platen Casting
Work Rest Casting
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
3A 9049821
4
5
6
7
8
5507582
9100331
9074011
9074081
5510946
5510947
5510948
5053231
9074381
9112811
Lock Washer
, 5/16
Latch, Cam
9
10
11
Nut, Hex, 5/16-18
Washer, Nylon 5/16
Door
Knob, Hand
Guard FlapAssembly
Washer, Flat 0.26 x 0.63 x 0.06
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
5044400
5044410
5044370
9128441
5049990
9129881
9055361
9129861
5046571
9055381
9010271
5044651
9133041
5046560
9133191
9129561
9059811
5053301
Head Casting
Tracking Leader
Assembly
Screw, Socket Head Cap 3/8-16 x 1
Screw, Work Rest Machine
Screw, Socket Head Cap 3/8-16 x 5/8
Flat Washer, Nylon 1/2 I.D. x 1 O.D.
Scr, Socket Head Cap, Fll
Bearing, Idler Housing
Flat Washer, Nylon, 3/8
O-Ring, 1/2
Casting, Idler Housing
Main FrameAssembly
Thrd, 3/8-24 x 3
Cap, Idler Housing Pin
Set Screw, Socket Head 1/4-20 x 1/4
Lever, Tension
Set Screw, Nylon
Tipped 5/16-18 x 3/4
Locknut, Hex, 3/8-24
Roll Pin, 3/16 x 1-1/2
Shaft, Idler Pulley
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List - Inverter
Ref. Part
Ref. Part
No. Number Description
Qty.
7
No. Number Description
Qty.
1
2
5550874 Screw, Socket head
Cap, 10-32NF x 3/8
6
7
9
5508073 Nut, Lock, 10-32 Nylock
5507934 Box, Switch
9119721 Spade, Female 16-14AWG
4
1
4
1
1
2
1
5507817 inverter (1ph, 120V, 50/60Hz)
5507818 Inverter (3ph, 220V, 50/60Hz)
5511447 Inverter (3ph, 440V, 50/60Hz)
9128571 Screw, Hex Head 1/2-13 x 1
5515215 Mount, Inverter
1
10 9117401 Switch, Toggle
12 9085061 Dial, ON-OFF
13 9119071 Grip, Cord
3
4
5
1
1
1
14 5628371 Lock Washer, 1/2
9119481 Terminal, Full Closed
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Belt Grinder Pedestal
The optional pedestal enables the Square Wheel Belt
Grinder to be mounted in a free standing configuration
rather than on a work bench. The grinder is secured
to the pedestal using the four holes in the base of the
grinder (refer to page 22).
Dust Collection Systems
A dust collection system is available as an option
(refer to page 24 for additional coverage).
The dust collection system can be used in two con-
figurations: as a machine base (Figure 9) or as a
stand- alone system (Figure 8).
Figure 8: Stand-Alone Dust Collection System
In the stand-alone configuration, the dust collection
system is placed next to the grinding machine, and the
dust collection hose connected to the inlet duct. It
may also be placed between two grinding machines,
making use of the inlet ducts on both sides of the dust
collection system.
Another option is to use the dust collection system as
a base for the Model 4103 grinding machine in lieu of
placing the machine on a bench or on the pedestal.
The second inlet duct on the side of the system is
available for connecting another grinding machine. In
areas with limited space, this may be the most desir-
able option.
17
The dust collection system features a chip drawer into
which grinding debris is collected. The dust collection
system has a filter at the rear to filter out remaining
grinding debris.
The system has a removable top that provides access
for cleaning and maintenance. The system is con-
trolled by an ON/OFF toggle switch on the motor at the
rear of the machine.
Figure 9: Dust Collection System -
Used as Grinder Base
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View - Vacuum Scoop
A vacuum scoop connects the machine to the vacuum system. The mounting provisions for the scoop are
shown in the exploded view below.
15
7
14
13
10
1
12
10
12
11
10
2
9
3
4
8
7
6
5
18
Ref. Part
No. Number Description
Ref. Part
No. Number Description
Qty.
Qty.
1
2
3
5053531 ScoopAssembly
5052471 Adapter, Hose
5053601 Reducer, 4 x 3 in.
(Woodworkers)
5053611 Reducer, 4 x 3 in.
(Metal Workers)
5507534 Clamp, Hose 3 in.
5507533 Hose, 3 x 5 in.
9128241 Screw, HH Cap
9070361 Knob
1
1
1
8
9
5053571 Rail
9032961 Lock Nut, Nylon Insert
1
4
8
1
2
3
2
2
10 9055411 Washer, Nylon
11 5053581 Channel
1
12 9057391 Washer, Flat
13 9056411 Nut, Hex Jam
14 9062111 Screw, SHCS (5/16-18 X 3/4)
15 9146801 Screw, SHCS Low Head
(5/16-18 X 1 1/2)
4
5
6
7
1
1
3
2
Figure 11: Vacuum Scoop Exploded View
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Cushioned Dead Head Assembly
2
8
7
6
Refer to Figures 10 and 11. The air-cushioned dead
head is for use on very small radius grinding. When
connected to a source of shop air (80-90 psi), the
belt rides on a cushion of air to decrease head and
belt wear. The dead head is easy to use, and adapts
to any of the available radius tips.
1
4
5
3
Ref. Part
No. Number
Description
Qty.
1
5044960 Air Cushion Dead Head
Assembly (Note 1)
1
2
3
5044970 Casting, Dead Head
1
1
1
1
1
1
5044991 Tip, Dead Head, 3/16 R x 2
5045011 Tip, Dead Head, 1/4 R x 2
5045031 Tip, Dead Head, 5/16 R x 2
5045051 Tip, Dead Head, 3/8 R x 2
5045071 Fitting, Flareless Com-
pression, 1/4 x 1/8
4
5
5044610 Contact Wheel Assembly
3 x 2
1
6
7
5045101 Spacer
9062441 Screw, Socket Head Cap
10-32 x 1/2
1
2
Figure 10: Internal Contouring
with Air Cushioned Dead Head
8
9049761 Screw, Socket Head Flare
1
Note 1: Includes 3/8 R x 2 dead head tip 5045051.
Other tips available at additional cost.
Install the dead head assembly as follows:
WARNING: DISCONNECT ELECTRICAL POWER
TO THE MACHINE BEFORE INSTALLING THE
DEAD HEAD ASSEMBLY.
Figure 11: Air Cushioned Dead
Head Assembly Parts Breakdown
1. Lower tension lever to release belt tension.
2. Loosen clamping screw and remove platen or
contact wheel.
19
3. Insert the shaft of the dead head assembly in
head casting. Position dead head assembly
with the tip parallel with the machine base.
Tighten the clamping screw.
4. Install the belt under the dead head contact
wheel and over the dead head tip.
5. Lift the tension lever to tighten the belt.
6. Check belt tracking.
7. Connect pressurized air supply (80-90 psi).
8. Check operation of the dead head assembly.
Download from Www.Somanuals.com. All Manuals Search And Download.
Hub and Wheel Assembly
Refer to Figures 12 and 13. The hub and wheel
assembly Small Diameter Contact Wheels
can be used to adapt a number of other optional
attachments for use on the belt grinder. The assem-
bly consists of a pre-balanced hub shaft, collar, and
V-belt and a special wrench to enable quick change
of the optional attachments.
V-Belt
Collar
Hub Shaft
4
1
Ref. Part
No. Number
Description
Qty.
1
5054920 Hub and Wheel Assembly
(Includes Hub Shaft, V-Belt,
Collar, and Special Wrench)
5045141 Polishing Wheel
5058071 Spacer Plate
1
2
3
4
1
2
1
5044620 Buffer Pad
Figure 12: Polishing with
Hub and Wheel Assembly
Figure 13: Hub and Wheel Assembly
Install the hub and wheel assembly as follows:
WARNING: DISCONNECT ELECTRICAL
POWER TO THE MACHINE BEFORE INSTALL-
ING THE HUB AND WHEEL ASSEMBLY.
20
1. Lower tension lever to release belt tension.
2. Loosen clamping screw and remove platen
or contact wheel.
3. Remove work rest.
3. Insert the shaft of the hub in head casting.
Tighten the clamping screw.
4. Install the V-belt around the idler wheel,
drive wheel, and wheel of hub and wheel
assembly.
5. Raise tension lever to tighten belt.
6. Install polishing wheel or buffing pad as
follows:
A. Install one spacer plate on threaded
shaft.
B. Install polishing wheel or buffing pad.
C. Install second spacer plate and collar.
D. Tighten collar using special wrench.
Download from Www.Somanuals.com. All Manuals Search And Download.
Small Diameter Contact Wheels
Small diameter contact wheels are useful for grinding
or contouring difficult, hard to reach areas (refer to
Figure 15). The small diameter contact wheels are
available in several sizes. Refer to Figure 14 for a
listing of small diameter contact wheels.
Dia.
(In.)
1/2
5/8
3/4
1
Part Number
5057871
5057881
5057891
5057901
Description
Contact Wheel, 70 Duro
Contact Wheel, 70 Duro
Contact Wheel, 70 Duro
Contact Wheel, 70 Duro
Figure 14: Small Diameter Contact Wheels.
Assembly of Pedestal
Unpacking
Figure 15: Contouring Using Small
Diameter Contact Wheel
The grinding machine pedestal is shipped separately
from the grinding machine. Transport the shipping
containers to the installation site before unpacking.
Unpack the pedestal and grinding machine. Locate and
open the plastic bag containing four 5/16-18 socket
head cap screws. Verify that that there are two screws
1-inch long and two screws 1-3/4 inches long (Figure
16, View A).
MAKE SURE THE GRINDING MACHINE IS
CORRECTLY POSITIONED AND SECURED TO
THE PEDESTAL BEFORE LEAVING THE
MACHINE UNATTENDED. FAILURE TO COR-
RECTLY POSITION AND SECURE THE MA-
CHINE COULD RESULT IN THE MACHINE
TIPPING OVER, CAUSING INJURY TO PER-
SONNEL.
Securing the Pedestal
WARNING: BOLTING THE PEDESTAL TO THE
FLOOR IS STRONGLY RECOMMENDED. THE
PEDESTAL IS BOLTED TO THE FLOOR TO
ELIMINATE THE POSSIBILITY OF TIP-OVER
WHILE THE MACHINE IS BEING OPERATED.
FAILURE TO DO SO CAN RESULT IN INJURY
TO THE OPERATOR AND/OR OTHER NEARBY
PERSONNEL.
There are four mounting holes in the mounting plate on
the pedestal. The holes on the motor side of the machine
are approximately 20 inches apart. The holes on the
belt-guard side of the machine are located approximately
½-inch from the corners of the plate. When correctly
installed, all four screw holes in the machine base plate
and belt guard will align with the holes in the mounting
plate of the pedestal.
21
Mounting Procedure
The pedestal has four mounting holes in its base.
Use these mounting holes to secure the pedestal to
the floor before installing the grinder. Shims should
be used to level the pedestal before the attaching
bolts are tightened.
A. Using two people or a hoisting device, lift the grind-
ing machine and set it on the pedestal. Align all
four screw holes in the machine base plate and
belt guard with the holes in the mounting plate of
the pedestal (Figure 16, View B).
B. Open the grinding belt guard door (Figure 16, View
C). Install two 5/16-18 x 1-inch long screws in the
base of the grinding belt guard. Install screws
finger-tight.
Assembly
WARNING: THE MACHINE MOUNTING PLATE IS
NOT CENTERED ON THE LEG OF THE PEDES-
TAL. THIS OFFSET EVENLY DISTRIBUTES
THE WEIGHT OF THE GRINDING MACHINE.
C. Install the two 5/16-18 x 1-3/4-inch long screws in
the screw holes on the motor side of the machine
base (Figure 16, View D). Tighten all four screws.
Download from Www.Somanuals.com. All Manuals Search And Download.
B
A
Belt Guard Holes
Approximately
1/2-inch from
corners
2
3
Motor Side
Holes
20 inches
apart
1
C
D
3
Install two 1-
inch long
screws
22
Install two
1 3/4-inch
screws
2
Ref. No.
Part Number
Description
Pedestal
Socket Head Cap Screw (5/16-18 x 1)
Socket Head Cap Screw (5/16-18 x 1 3/4)
Qty.
1
2
1
2
3
5248081
9062121
5511051
2
Figure 16: Assembly of Grinding Machine and Pedestal
Download from Www.Somanuals.com. All Manuals Search And Download.
Dust Collection System (Optional)
Installation
Transport the shipping container to the installation site.
Filter
Unpack the dust collection system and check for
damage. Contact the carrier if damage is found.
Check for accumulation of debris. Replace the filter
at intervals that you determine are appropriate for
your shop environment and machine utilization.
Open the installation kit (refer to Optional
Accessories in the parts listing for installation kits).
Install cover and debris collection drawer if removed.
Slip a hose clamp over the 3-inch vacuum hose. Slip
the hose on the inlet duct(s). Move the clamp over the
duct to secure the hose.
Drawer Seal
Check the drawer seal periodically and replace if
damaged or missing. Keep the seal in good condition
to help maintain collection system efficiency.
Repeat the procedure to connect the hose to the other
duct on the grinding machine.
Removable cover –
ON/OFF switch on
remove for interior
motor at rear of dust
cleaning/access to
collection system
Electrical Connection
impeller
Refer to the Dust Collection System Wiring Diagram
for wiring information. Connection to electrical power
should be made by a qualified electrician. Observe
local electrical codes when connecting the machine.
Second Inlet
Duct on this side
Operation
The dust collection system motor is started by setting
the toggle switch on the motor to the ON position. Set
the switch to OFF to shut down the dust collection
system.
Maintenance
23
WARNING:
· MAKE SURE YOU DISCONNECT ELECTRICAL
POWER TO THE DUST COLLECTION SYSTEM
BEFORE PERFORMING MAINTENANCE.
FAILURE TO DO SO MAY RESULT INJURY TO
THE OPERATOR AND/OR MAINTENANCE
PERSONNEL.
· DO NOT OPERATE THE DUST COLLECTION
SYSTEM WITH THE COVER REMOVED. INJURY
TO FINGERS AND HANDS FROM THE FAN
BLADES, AND INGESTION OF LOOSE FITTING
CLOTHING INTO THE AIR INLET WITH RESULT-
ANT INJURY IS ALSO POSSIBLE.
Outlet filter at rear
removes fine debris
from outlet air stream
Chip Drawer -
Pull to Open
Inlet Duct – Connect
3 inch hose - secure
with clamp
Figure 17: Dust Collector Assembled View
Cleaning
Periodically dispose of accumulated chips and debris
from the chip drawer. Use a brush to loosen debris
from internal surfaces. Use a vacuum cleaner to clean
up the loosened debris.
Download from Www.Somanuals.com. All Manuals Search And Download.
Disassembly
Disassembly of the dust collection system is re-
quired only to replace the motor or the fan compo-
nents. The motor switch, if failed, can be replaced
without removal of the motor.
1. Remove chip drawer (2) and cover (4) from
base (1).
2. Remove the filter cover (5) and filter (6). Re-
place filter if required.
3. Remove five nuts (10) and lock washers (11)
from studs at rear of base (1).
4. Remove four nuts (12) and lock washers (13)
from screws (14). Remove screws (14) from
inside fan housings. Separate motor support
panel (9) (with fan and motor still attached) from
base (1).
5. Remove five nuts (17), lock washers (18) and
screws (19) that secure the fan housings
together.
6. Using a flat bladed tool, separate the outer fan
housing (16) from the inner fan housing (24).
7. Using an Allen wrench, loosen set screw (22).
Remove fan (21) from shaft of motor (25).
Remove key (23) from motor shaft.
8. Use a flat-bladed screwdriver to hold flat head
screws (28) (in inner fan housing). Remove four
nuts (26) and lock washers (27) from the flat
head screws (28) in motor mounting lugs.
Assembly
Assembly is the reverse of disassembly. Observe the
following during assembly:
1. Assemble motor (25) and inner fan housing (24)
on rear panel; make sure fan duct is facing
downward.
2. Make sure guard strap (20) is installed in the
recesses in fan duct.
24
3. Mate fan housings (16 and 24). Turn fan (21) by
hand to check for rubbing. Adjust fan as re-
quired.
4. Use a spare screw or a Phillips screwdriver to
align screw holes in outer fan housing (16),
spacer (15), and in the internal panel of base
(1).
5. With the screw holes aligned, install the support
panel (9) on the five studs at the rear of base
(1).
6. Connect electrical power and check operation
of the dust collection system.
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View – Model 5511885 Dust Collection System
15
14
16
21
22
26
24
27
9
19
20
23
12
13
18
28
17
25
11
10
5
4
6
25
REAR VIEW
7
8
1
2
FRONT VIEW
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List – Model 5511885 Dust Collection System
Ref. Part
No. Number
Ref.
No.
19
20
21
22
23
24
25
26
27
28
Part
Description
Base
Qty
1
Number
5514748
5514749
5514750
5514751
5514752
5514753
5514754
5514755
5514756
5514757
Description
Qty
5
1
1
1
1
1
1
4
1
2
3
4
5
6
7
8
5514731
5514732
5514733
5514734
5514735
5514779
5514736
5514737
5514738
5514739
5514740
5514741
5514742
5514743
5514744
5514745
5514746
5514747
Screw, Hex Head
Strap, Guard
Fan
Screw, Set
Key
Housing, Inner Fan
Motor
Screw, Hex Head
Seal, Tape 5-feet long
Switch, Motor
Drawer, Chip
Seal, Tape (5-feet long)
Cover
Cover, Filter
Filter
Panel, Rear Foam
Panel, Side Foam
Panel, Motor Support
Nut, Hex
Washer, Lock
Nut, Hex
Washer, Lock
Screw, Hex Head
Spacer
Housing, Outer Fan
Nut, Hex
1
1
1
1
2
1
5
5
4
4
4
1
1
5
5
9
1
1
10
11
12
13
14
15
16
17
18
Connection Kits:
Refer to Wilton catalog for appropriate connection
kit for your grinding machine or contact Wilton for
assistance.
Washer, Lock
Wiring Information - Dust Collection System
26
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123
Phone: 800-274-6848
Download from Www.Somanuals.com. All Manuals Search And Download.
|