®
ELECTRIC RANGE
Use & Care Guide
For questions about features, operation/performance
parts, accessories or service, call: 1-800-253-1301.
or visit our website at...
Table of Contents................................................. 2
9756384
Download from Www.Somanuals.com. All Manuals Search And Download.
RANGE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
The Anti-Tip Bracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the
anti-tip bracket fastened down properly.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
See the installation instructions for details.
Failure to follow these instructions can result in death or serious burns to children
and adults.
Anti-Tip Bracket
Making sure the anti-tip bracket is installed:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor.
• Slide range back so rear range foot is under anti-tip bracket.
Range Foot
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list
of substances known to the State of California to cause cancer, birth defects, or other reproductive harm, and
requires businesses to warn of potential exposure to such substances.
WARNING: This product contains a chemical known to the State of California to cause cancer, birth defects, or
other reproductive harm.
This appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde,
carbon monoxide, and toluene.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical
I Use Proper Pan Size – The range is equipped with
one or more surface units of different size. Select
utensils having flat bottoms large enough to cover
the surface unit heating element. The use of under-
sized utensils will expose a portion of the heating
element to direct contact and may result in ignition
of clothing. Proper relationship of utensil to burner
will also improve efficiency.
shock, injury to persons, or damage when using the
range, follow basic precautions, including the
following:
I
WARNING: TO REDUCE THE RISK OF
TIPPING OF THE RANGE, THE RANGE MUST BE
SECURED BY PROPERLY INSTALLED ANTI-TIP
DEVICES. TO CHECK IF THE DEVICES ARE
INSTALLED PROPERLY, SLIDE RANGE FORWARD,
LOOK FOR ANTI-TIP BRACKET SECURELY
ATTACHED TO FLOOR, AND SLIDE RANGE BACK
SO REAR RANGE FOOT IS UNDER ANTI-TIP
BRACKET.
I Never Leave Surface Units Unattended at High Heat
Settings – Boilover causes smoking and greasy
spillovers that may ignite.
I Make Sure Reflector Pans or Drip Bowls Are in
Place – Absence of these pans or bowls during
cooking may subject wiring or components under-
neath to damage.
I
CAUTION: Do not store items of interest to
children in cabinets above a range or on the back-
guard of a range – children climbing on the range to
reach items could be seriously injured.
I Protective Liners – Do not use aluminum foil to line
surface unit drip bowls or oven bottoms, except as
suggested in the manual. Improper installation of
these liners may result in a risk of electric shock, or
fire.
I Proper Installation – Be sure the range is properly
installed and grounded by a qualified technician.
I Never Use the Range for Warming or Heating the
Room.
I Glazed Cooking Utensils – Only certain types of
glass, glass/ceramic, ceramic, earthenware, or other
glazed utensils are suitable for range-top service
without breaking due to the sudden change in
temperature.
I Do Not Leave Children Alone – Children should not
be left alone or unattended in area where the range
is in use. They should never be allowed to sit or
stand on any part of the range.
I Utensil Handles Should Be Turned Inward and Not
Extend Over Adjacent Surface Units – To reduce the
risk of burns, ignition of flammable materials, and
spillage due to unintentional contact with the utensil,
the handle of a utensil should be positioned so that
it is turned inward, and does not extend over
adjacent surface units.
I Wear Proper Apparel – Loose-fitting or hanging
garments should never be worn while using the
range.
I User Servicing – Do not repair or replace any part of
the range unless specifically recommended in the
manual. All other servicing should be referred to a
qualified technician.
I Do Not Soak Removable Heating Elements –
Heating elements should never be immersed in
water.
I Storage in or on the Range – Flammable materials
should not be stored in an oven or near surface
units.
I Do Not Cook on Broken Cooktop – If cooktop
should break, cleaning solutions and spillovers may
penetrate the broken cooktop and create a risk of
electric shock. Contact a qualified technician
immediately.
I Do Not Use Water on Grease Fires – Smother fire or
flame or use dry chemical or foam-type extinguisher.
I Use Only Dry Potholders – Moist or damp
potholders on hot surfaces may result in burns from
steam. Do not let potholder touch hot heating
elements. Do not use a towel or other bulky cloth.
I Clean Cooktop With Caution – If a wet sponge or
cloth is used to wipe spills on a hot cooking area,
be careful to avoid steam burn. Some cleaners can
produce noxious fumes if applied to a hot surface.
I DO NOT TOUCH SURFACE UNITS OR AREAS
NEAR UNITS – Surface units may be hot even
though they are dark in color. Areas near surface
units may become hot enough to cause burns.
During and after use, do not touch, or let clothing or
other flammable materials contact surface units or
areas near units until they have had sufficient time
to cool. Among those areas are the cooktop and
surfaces facing the cooktop.
I Use Care When Opening Door – Let hot air or
steam escape before removing or replacing food.
I Do Not Heat Unopened Food Containers – Build-up
of pressure may cause container to burst and result
in injury.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
For self-cleaning ranges –
I Keep Oven Vent Ducts Unobstructed.
I Do Not Clean Door Gasket – The door gasket is
essential for a good seal. Care should be taken not
to rub, damage, or move the gasket.
I Placement of Oven Racks – Always place oven
racks in desired location while oven is cool. If rack
must be moved while oven is hot, do not let
potholder contact hot heating element in oven.
I Do Not Use Oven Cleaners – No commercial oven
cleaner or oven liner protective coating of any kind
should be used in or around any part of the oven.
I DO NOT TOUCH HEATING ELEMENTS OR
INTERIOR SURFACES OF OVEN – Heating
elements may be hot even though they are dark in
color. Interior surfaces of an oven become hot
enough to cause burns. During and after use, do
not touch, or let clothing or other flammable
materials contact heating elements or interior
surfaces of oven until they have had sufficient time
to cool. Other surfaces of the appliance may
become hot enough to cause burns – among these
surfaces are oven vent openings and surfaces near
these openings, oven doors, and windows of oven
doors.
I Clean Only Parts Listed in Manual.
I Before Self-Cleaning the Oven – Remove broiler pan
and other utensils.
For units with ventilating hood –
I Clean Ventilating Hoods Frequently – Grease should
not be allowed to accumulate on hood or filter.
I When flaming foods under the hood, turn the fan on.
SAVE THESE INSTRUCTIONS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND FEATURES
This manual covers several different models. The range you have purchased may have some or all of the parts and features listed. The
location and appearance of the features shown here may not match your model.
Control Panel
6
3
7
2
4
5
1
8
10
9
1. ACCUSIMMER® Range Indicator Light
(on some models)
2. Left Front Control Knob
(ACCUSIMMER® Range Control Knob
on some models)
4. Left Rear Control Knob
5. Electronic Oven Control
6. Right Rear Control Knob
7. Right Front Control Knob
8. ACCUSIMMER® Range Switch (on some models)
9. Surface Cooking Area Locator
10. Keep Warm Element Control Knob
(on some models)
3. Surface Heating Indicator Light
Range
7
8
1
2
3
9
10
13
11
12
4
5
6
1. Oven Vent (on ceramic glass
models)
2. Ceramic Glass (on some
models)
3. Dual Element
(on some models)
6. Storage Drawer (on some
models) or Warming Drawer (on
some models)
7. Control Panel
8. Keep Warm Element
(on some models)
10. Automatic Oven Light Switch
11. Broil Element (not shown)
12. Bake Element
Parts and Features Not Shown
Coil Elements (on some models)
Oven Door Window
Oven Light
Broiler Pan and Grid
Roasting Rack
13. Self-Clean Latch
4. Anti-Tip Bracket
9. Hot Surface Indicator Light (on
ceramic glass models)
Storage Drawer Liner
(on some models)
5. Model and Serial Number Plate
(behind left side of storage
drawer)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCUSIMMER® Feature
COOKTOP USE
(on some models)
The ACCUSIMMER® feature setting is an adjustable heat setting
for more precise simmering. It is the left front surface cooking
area or element. The indicator light will glow when the
ACCUSIMMER® feature is in use.
Cooktop Controls
WARNING
(NOTE: Picture may vary depending on your model)
The ACCUSIMMER® control knob has two settings: SIMMER and
NORMAL BURNER. When the control is set on NORMAL
BURNER, the left front surface cooking area or element will
function as a single or dual element (on some models).
Fire Hazard
Turn off all controls when done cooking.
Failure to do so can result in death or fire.
To use:
1. Turn the ACCUSIMMER® Range control knob to the SIMMER
position. The indicator light will glow.
The control knobs can be set anywhere between HI and LO. Push
in and turn to setting. Use the following chart as a guide when
setting heat levels.
2. Push in and turn the left front control knob to a setting
between LO and 5.
Select LO for a low simmer or when using lids and 5 for a high
simmer or when not using lids.
SETTING
HI
RECOMMENDED USE
On some models, select either the Single or Dual Zone
settings. See “Dual Cooking Zone” section.
3. Turn the ACCUSIMMER® Range control knob back to the
Normal Burner setting when finished cooking. The indicator
light will go out.
I
I
Start food cooking.
Bring liquid to a boil.
I
I
Hold a rapid boil.
6-8
[MED- HI]
Quickly brown or sear food.
5
I
I
I
Maintain a slow boil.
Dual Cooking Zone
[MED]
Fry or sauté foods.
Cook soups, sauces and gravies.
(on some models)
2-4
[MED- LO]
I
I
Stew or steam food.
Simmer.
1
2
LO
I
I
Keep food warm.
Melt chocolate or butter.
ACCUSIMMER®
(on some models)
I
Precise simmer control.
I
I
Low simmer or when using lids.
4
LO
1. Single size (6 in. [15.24 cm])
2. Dual size (10 in. [25.4 cm])
High simmer or simmer without lids.
Keep Warm Element
(on some ceramic
glass models)
I
Keep cooked foods warm.
The Dual Cooking Zone offers flexibility depending on the size of
the cookware. Single size can be used in the same way as a
regular element. The dual size combines both the single and
outer element and is recommended for larger size cookware.
SINGLE
DUAL
OFF
LO
LO
2
2
REMEMBER: When range is in use or (on some
models) during the Self-Cleaning cycle, the entire
cooktop area may become hot.
4
4
6
6
8
8
HI
I H
1. Single
2. Dual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
To Use SINGLE:
1. Push in and turn the left front control knob counterclockwise
from the OFF position to the SINGLE zone anywhere between
HI and LO.
Ceramic Glass
(on some models)
2. Push in and turn knob to OFF when finished.
The surface cooking area will glow red when an element is on. It
will cycle on and off, at all settings, to maintain the selected heat
level.
To Use DUAL:
1. Push in and turn the left front control knob clockwise from the
It is normal for the surface of white ceramic glass to appear to
change color when surface cooking areas are hot. As the glass
cools, it will return to its original color.
OFF position to the DUAL zone anywhere between HI and
LO.
2. Push in and turn knob to OFF when finished.
Wiping off the cooktop before and after each use will help keep it
free from stains and provide the most even heating. For more
information, see “General Cleaning” section.
Keep Warm Element
I
Do not store jars or cans above the cooktop. Dropping a
heavy or hard object onto the cooktop could crack it.
(on some models)
I
Do not leave a hot lid on the cooktop. As the cooktop cools,
air can become trapped between the lid and the cooktop,
and the ceramic glass could break when the lid is removed.
WARNING
I
I
Clean up sugary spills and soils as soon as hot surface
indicator light goes off. If spills or soils are not wiped up while
warm, surface pitting can occur.
Food Poisoning Hazard
Do not let food sit for more than one hour before
or after cooking.
Do not slide cookware or bakeware across the cooktop.
Aluminum or copper bottoms and rough finishes on
cookware or bakeware could leave scratches or marks on the
cooktop.
Doing so can result in food poisoning or
sickness.
I
I
Do not cook popcorn in prepackaged aluminum containers
on the cooktop. It could leave aluminum marks that cannot
be removed completely.
Use the Keep Warm Element to keep cooked foods warm. One
hour is the recommended maximum time to maintain food
quality.
Do not allow objects that could melt, such as plastic or
aluminum foil, to touch any part of the entire cooktop.
Do not use it to heat cold foods.
The Keep Warm Element can be used alone or when any of the
other surface cooking areas are being used, and can be set from
MIN to MAX for different levels of heating.
I
I
Do not use the cooktop as a cutting board.
Use cookware about the same size as the surface cooking
area. Cookware should not extend more than 1 in. (2.5 cm)
outside the area.
The Keep Warm Element area will not glow red when cycling on.
However, its indicator light will glow as long as the Keep Warm
Element area is too hot to touch.
I
Use only cookware and dishes recommended for oven and
cooktop use.
I
Cover all foods with a lid or aluminum foil. When warming
baked goods, allow a small opening in the cover for moisture
to escape.
I
I
Do not use plastic wrap to cover food. Plastic wrap may melt.
Use pot holders or oven mitts to remove food.
KEEP WARM
1. Surface Cooking Area
2. Cookware/Canner
3. 1 in. (2.5 cm) Maximum Overhang
OFF MAX
MIN
I
I
Use flat-bottomed cookware for best heat conduction and
energy efficiency. Cookware with rounded, warped, ribbed or
dented bottoms could cause uneven heating and poor
cooking results.
Determine flatness by placing the straight edge of a ruler
across the bottom of the cookware. While rotating the ruler,
no space or light should be visible between it and the
cookware.
To Use:
I
I
Cookware designed with slightly indented bottoms or small
expansion channels can be used.
1. Push in and turn KEEP WARM knob to desired setting.
2. Turn knob to OFF when finished.
Make sure the bottoms of pots and pans are clean and dry
before using them. Residue and water can leave deposits
when heated.
I
Do not cook foods directly on the cooktop.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Hot Surface Indicator Light (under ceramic glass)
The hot surface indicator light will glow as long as any surface
cooking area is too hot to touch, even after the surface cooking
area(s) is turned off.
Lift-up Cooktop
(on some models)
The lift-up cooktop provides easy access for cleaning beneath.
Do not drop the cooktop. Damage could occur to the finish and
the cooktop frame. For more information, see the “General
Cleaning” section.
HOT SURFACE
To Lift:
Lift the cooktop by both front corners until the supports lock into
place.
Coil Elements and Burner Bowls
(on some models)
Coil elements should be level for optimal cooking results. Burner
bowls, when clean, reflect heat back to the cookware. They also
help catch spills.
Cookware should not extend more than 1 in. (2.5 cm) over the
coil element. If cookware is uneven or too large, it can produce
excess heat causing the burner bowl to change color. For more
information, see the “General Cleaning” section.
To Replace:
Before removing or replacing coil elements and burner bowls,
make sure they are cool and the control knobs are in the off
position.
1. Lift the cooktop from both sides while pressing the support
rods back to unlock them.
2. Slowly lower the cooktop into place.
To Remove:
1. Push in the edge of coil element toward the receptacle. Then
lift it just enough to clear the burner bowl.
Home Canning
When canning for long periods, alternate the use of surface
cooking areas, elements or surface burners between batches.
This allows time for the most recently used areas to cool.
I
Center the canner on the grate or largest surface cooking
area or element. Canners should not extend more than 1 in.
(2.5 cm) outside the cooking area.
I
Do not place canner on two surface cooking areas, elements
or surface burners at the same time.
2. Pull the coil element straight away from the receptacle.
I
I
On ceramic glass models, use only flat-bottomed canners.
On coil element models, the installation of a Canning Unit Kit
is recommended. If a kit is not installed, the life of the coil
element will be shortened. See “Assistance or Service” for
ordering instructions.
I
For more information, contact your local U.S. Government
Agricultural Department Extension Office. In Canada, contact
Agriculture Canada. Companies that manufacture home
canning products can also offer assistance.
3. Lift out the burner bowl.
To Replace:
1. Line up openings in the burner bowl with the coil element
Cookware
receptacle.
IMPORTANT: Never leave empty cookware on a hot surface
cooking area, element or surface burner.
Ideal cookware should have a flat bottom, straight sides, a well-
fitting lid and the material should be of medium-to-heavy
thickness.
Rough finishes may scratch the cooktop. Aluminum and copper
may be used as a core or base in cookware. However, when used
as a base they can leave permanent marks on the cooktop or
grates.
2. Holding the coil element as level as possible, carefully push
coil element terminal into the receptacle.
Cookware material is a factor in how quickly and evenly heat is
transferred, which affects cooking results. A nonstick finish has
the same characteristics as its base material. For example,
aluminum cookware with a nonstick finish will take on the
properties of aluminum.
3. When the terminal is pushed into the receptacle as far as it
will go, push down the edge of the coil element opposite the
receptacle.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the following chart as a guide for cookware material
characteristics.
Style 2 Electronic Oven Controls (on some models)
2 4 5
1
3
6
COOKWARE
Aluminum
CHARACTERISTICS
I
I
I
Heats quickly and evenly.
Suitable for all types of cooking.
Medium or heavy thickness is best for
most cooking tasks.
Cast iron
I
I
I
Heats slowly and evenly.
Good for browning and frying.
Maintains heat for slow cooking.
Ceramic or
Ceramic glass
I
I
I
Follow manufacturer’s instructions.
Heats slowly, but unevenly.
11
10
9
8
7
Ideal results on low to medium heat
settings.
1. Oven Display
2. Clock
3. Timer/Cancel
7. Temperature/Time
8. Cook Time
9. Start Time
Heats very quickly and evenly.
Copper
I
4. Start/Enter
(Control Lock)
5. Auto Clean
6. Off/Cancel
10. Custom Broil
11. Bake
I
I
Follow manufacturer’s instructions.
Earthenware
Use on low heat settings.
I
See stainless steel or cast iron.
Porcelain enamel-
on-steel or cast
iron
Display
Stainless steel
I
I
Heats quickly, but unevenly.
When power is first supplied to the appliance, “PF” will appear on
the display. Press CANCEL or OFF/CANCEL to clear “PF” from
the display.
A core or base of aluminum or copper on
stainless steel provides even heating.
If “PF” appears at any other time, a power failure has occurred.
Press CANCEL or OFF/CANCEL and reset the Clock if needed.
ELECTRONIC OVEN
CONTROLS
When the oven is not in use, the display shows the time of day.
When performing a timed cook function, the display will show
either hours and minutes, or minutes and seconds.
Style 1 Electronic Oven Controls (on some models)
Start
The START or START/ENTER pad begins any oven function. If not
pressed within 5 seconds after pressing a function pad, the
“START?” indicator light will flash as a reminder. On some
models, “START?” will appear on the display.
If not pressed within 5 minutes after pressing a function pad, the
oven display will return to the time of day mode and the
programmed function will be canceled.
Cancel or Off/Cancel
The CANCEL or OFF/CANCEL pad stops any function except the
Clock, Timer and Control Lock.
1. Display
2. Timer
3. Clock
4. Auto Clean
5. Oven Light Pad (on some
models)
6. Sequence Programming
(on some models)
7. Oven Settings
8. Warming Drawer
(on some models)
9. Temperature
10. Timed Cooking
(on some models)
11. Hour/Minute
(on some models)
Clock
On some models, this is a 12-hour clock that shows a.m. and
p.m.
12. Start/Control Lock
13. Off/Cancel
To Set:
Before setting, make sure the oven and Timer are off.
1. Press CLOCK.
2. Depending on your model, press the HR or MIN or TIME/
TEMP “up” or “down” arrow pads to set the time of day. Only
on some models can the time be set to include a.m. or p.m.
3. Press CLOCK or START.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
To display the time of day for 5 seconds when the timer is
counting down, press CLOCK.
Tones
Tones are audible signals, indicating the following:
Control Lock
One tone
The Control Lock shuts down the control panel pads to prevent
unintended use of the oven.
I
I
I
I
Valid pad press
When the control is locked, only the ACCUSIMMER, CLOCK SET,
OVEN LIGHT (on some models) and TIMER pads will function.
Oven is preheated (long tone)
Function has been entered
To Lock/Unlock Control: Before locking, make sure the oven
and Timer are off. Press and hold START for 5 seconds. A single
tone will sound, and “Loc” will appear on the display.
Reminder (on some models), repeating each minute after the
end-of-cycle tones
Repeat to unlock. “Loc” will disappear from the display.
Three tones
I
Invalid pad press
Oven Temperature Control
Four tones
IMPORTANT: Do not use a thermometer to measure oven
temperature because opening the oven door may cause burner
cycling to give incorrect readings.
I
End of cycle
Reminder Tones (on some models): Reminder tones may be
turned off. Press and hold STOP TIME for 5 seconds. “rEP OFF”
or “off” will appear in the display. Repeat to turn reminder tones
back on, and “rEP on” or “on” will appear in the display.
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature
calibration can be adjusted. It can be changed in Fahrenheit or
Celsius.
All Tones: All of the above tones are preset on. All except the
end-of-cycle tones can be turned off.
A minus sign means the oven will be cooler by the displayed
amount. No sign means the oven will be warmer by the displayed
amount. Use the following chart as a guide.
To Turn Off/On (on some models): Press and hold START TIME
for 5 seconds. A tone will sound and “Snd OFF” will appear on
the display. Repeat to turn tones on, and “Snd on” will appear on
the display.
ADJUSTMENT °F
(ADJUSTMENT °C)
COOKS FOOD
On some models, only the loudness of the tones can be adjusted.
On other models, the tones cannot be adjusted or turned off.
10°F (5°C)
...a little more
...moderately more
...much more
Tone Pitch: The pitch is preset at high, but can be changed to
low. On some models, only the loudness of the tones can be
adjusted. On other models, the tones cannot be adjusted or
turned off.
20°F (10°C)
30°F (15°C)
-10°F (-5°C)
-20°F (-10°C)
-30°F (-15°C)
To Change (on some models): Press and hold BAKE for 5
seconds. A tone will sound, and “Snd LO” will appear on the
display. Repeat to change, and “Snd Hi” will appear on display.
...a little less
...moderately less
...much less
Fahrenheit and Celsius
The temperature is preset at Fahrenheit, but can be changed to
Celsius on some models.
To Adjust Oven Temperature Calibration:
1. Press and hold BAKE for 5 seconds until the oven display
shows the current calibration, for example “0°F CAL” or “00.”
To Change: Press and hold CUSTOM BROIL for 5 seconds. A
tone will sound, and “°C” will appear on the display. Repeat to
change back to Fahrenheit. To exit mode, press CANCEL.
2. Press the TEMP or TEMP/TIME “up” or “down” arrow pad(s)
to increase or to decrease the temperature in 10°F (5°C)
amounts. The adjustment can be set between 30°F (15°C)
and -30°F (-15°C).
Timer
The Timer can be set in hours or minutes up to 12 hours and 59
minutes, and counts down the set time. The Timer does not start
or stop the oven.
3. Press START.
OVEN USE
To Set:
1. Press TIMER SET or TIMER CANCEL*. The timer indicator
light will light up on some models. If no action is taken after 5
minutes, the display will return to the time of day mode.
Odors and smoke are normal when the oven is used the first few
times, or when it is heavily soiled.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and well
ventilated room.
2. Depending on your model, press the HR or MIN or TIME/
TEMP “up” or “down” arrow pads to set the length of time to
cook.
3. Press START or TIMER SET. When the set time ends, end-of-
cycle tones will sound, then, if enabled, reminder tones will
sound every minute on some models.
4. Press TIMER OFF or TIMER CANCEL* anytime to cancel the
Timer and reminder tones.
Remember, do not press the CANCEL pad because the oven
will turn off.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Aluminum Foil
Split Oven Rack
IMPORTANT: Do not line the oven bottom with any type of foil,
liners or cookware because permanent damage will occur to the
oven bottom finish.
(on some models)
Split-Rack with Removable Insert
I
Do not cover entire rack with foil because air must be able to
move freely for best cooking results.
The split-rack with removable insert is a space maximizer. When
the two are attached, they make a full rack. The insert can also be
removed to provide room for large items such as a turkey and
casseroles.
I
To catch spills, place foil on rack below dish. Make sure foil is
at least 1 in. (2.5 cm) larger than the dish and that it is turned
up at the edges.
The insert can also be used on the counter for a cooling rack.
Do not place more than 25 lbs. (11.3 kg) on the split-rack.
I
Do not cover food with aluminum foil when convection
cooking (on some models).
2
Positioning Racks and Bakeware
1
IMPORTANT: Never place food or bakeware directly on the oven
door or bottom. Permanent damage will occur to the porcelain
finish.
1. Split-Rack
2. Removable Insert
RACKS
Position racks before turning the oven on. Do not move racks
with bakeware on them. Make sure racks are level. To move a
rack, pull it out to the stop position, raise the front edge, then lift
out. Use the following illustration and chart as a guide.
To Use Racks:
1. Place a full rack on position 1 or 2, and the split-rack on
position 3 or 4.
2. Place large items on the right side of the full rack.
3. Place deeper, covered dishes on the left side of the full rack.
4. Place shallow dishes on the split-rack.
5
4
3
5. When finished cooking, carefully remove items.
2
1
FOOD
RACK POSITION
Frozen pies, large roasts, turkeys, angel
food cakes
1 or 2
Bakeware
The bakeware material affects cooking results. Follow
Bundt cakes, most quick breads, yeast
breads, casseroles, meats
2
manufacturer’s recommendations and use the bakeware size
recommended in the recipe. Use the following chart as a guide.
Cookies, biscuits, muffins, cakes, pies
2 or 3
BAKEWARE/
RESULTS
RECOMMENDATIONS
BAKEWARE
I
I
Use temperature and time recommended
in recipe.
Light colored
aluminum
To cook food evenly, hot air must be able to circulate. Allow 2 in.
(5 cm) of space around bakeware and oven walls. Use the
following chart as a guide.
I
Light golden
crusts
I
Even browning
NUMBER OF
PAN(S)
POSITION ON RACK
May need to reduce baking temperatures
25°F (15°C).
Dark aluminum and
other bakeware
1
Center of rack.
with dark, dull and/
I
I
Use suggested baking time.
or nonstick finish
2
Side by side or slightly staggered.
For pies, breads and casseroles, use
temperature recommended in recipe.
I
Brown, crisp
crusts
3 or 4
Opposite corners on each rack. Make sure that no
bakeware piece is directly over another.
I
Place rack in center of oven.
Insulated cookie
sheets or baking
pans
I
I
Place in the bottom third of oven.
May need to increase baking time.
I
Little or no
bottom
browning
12
Download from Www.Somanuals.com. All Manuals Search And Download.
BAKEWARE/
RESULTS
RECOMMENDATIONS
Baking and Roasting
ACCUBAKE® DUO SYSTEM® Temperature Management
(on some models)
I
May need to increase baking time.
Stainless steel
I
Light, golden
crusts
The ACCUBAKE DUO SYSTEM technology electronically
regulates the oven heat levels during preheat and bake to
maintain the most uniform temperature control.
I
Uneven
browning
I
I
Follow manufacturer’s instructions.
Stoneware
Two temperature sensors will independently control the bake and
broil elements for optimal cooking results. The bake and broil
elements cycle on and off in intervals. The bake element will glow
red when cycling on, the broil element will not. This feature is
automatically activated when the oven is in use.
I
Crisp crusts
May need to reduce baking temperatures
25°F (15°C).
Ovenproof
glassware, ceramic
glass or ceramic
Before baking and roasting, position racks according to the
“Positioning Racks and Bakeware” section. When roasting, it is
not necessary to wait for the oven preheat conditioning time to
end before putting food in unless recommended in the recipe.
I
Brown, crisp
crusts
To Bake or Roast:
1. Press BAKE.
Meat Thermometer
On models without a temperature probe, always rely on a meat
thermometer to determine doneness of meat and poultry. The
internal temperature, not appearance, is what counts. A meat
thermometer is not supplied with this appliance.
2. Press TEMP or TEMP/TIME “up” or “down” arrow pad to set
a temperature other than 350°F (175°C) in 5 degree amounts.
The bake range can be set between 170°F and 500°F (75°C
and 260°C).
I
I
I
Insert the thermometer into the center of the thickest portion
of the meat or inner thigh or breast of poultry. The tip of the
thermometer should not touch fat, bone or gristle.
When the oven temperature is greater than 170°F (77°C), no
preheat conditioning time will be shown in the display. The
preheat conditioning time will not change if the temperature is
reset before the countdown time ends.
After reading the thermometer once, push it into the meat
¹⁄₂ in. (1.25 cm) more and read again. If the temperature
drops, cook the meat or poultry longer.
3. Press START. The temperature can be changed after this
step. START does not need to be pressed again.
Check all meat in two or three places.
If baking and roasting while the minute timer is counting
down, the set temperature can be seen for 5 seconds by
pressing BAKE.
Oven Vents
4. Press CANCEL or OFF when finished.
Preheating
2
After START is pressed, the oven will enter a timed preheat
conditioning. “PrE” (on some models) and the countdown time
will appear on the display. When the preheat conditioning time
ends, a tone will sound and the selected temperature will appear
on the display.
1
Preheat temperatures are affected by varying factors such as
room temperature and peak energy usage times. It is normal for
the temperature showing on the display and the actual oven
temperature to differ due to the cycling of the elements.
2. Ceramic Glass Models
1. Coil Element Models
The oven vent releases hot air and moisture from the oven, and
should not be blocked or covered. Doing so will cause poor air
circulation, affecting cooking and cleaning results. Never set
plastics, paper or other items that could melt or burn near the
oven vent.
Waiting an additional 10 minutes, after the preheat conditioning
time ends, to put food in the oven is suggested when baking
foods with leavening ingredients, such as yeast, baking powder,
baking soda and eggs.
On coil element models, the element can be used when the oven
is in use as long as the cookware does not extend more than 1 in.
(2.5 cm) over the element.
®
Choice Bake Function
(on some models)
The CHOICE BAKE® function eliminates the top heat during oven
cooking. It is ideal for baking pies, casseroles and breads, and for
roasting foods that require longer and slower cook times such as
poultry and roasts.
Similar to the baking and roasting function, the bake elements or
burners cycle on and off at intervals during CHOICE BAKE®
cycle. However, the cycle duration for the broil element is much
shorter during CHOICE BAKE®, allowing less top browning of
foods and more customized control for your baking results.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To Use:
To Broil:
1. Press CUSTOM BROIL.
1. Press CHOICE BAKE® function.
Press the TEMP “up” or “down” arrow pad to set a
temperature other that 350°F (175°C) in 5 degree amounts.
The bake range can be set between 170°F and 500°F (75°C
and 260°C).
2. Press START.
3. Press CANCEL when finished.
To Custom Broil:
1. Press CUSTOM BROIL.
2. Press START.
The temperature can be changed after this step. Start does
not need to be pressed again.
2. Press TEMP “up” or “down” arrow pad to change the
temperature in 5° amounts. The broil range can be set
between 300°F and 500°F (150°C and 260°C).
3. Press OFF/CANCEL when finished cooking.
3. Press START.
To use the CHOICE BAKE® function during a regular BAKE cycle
to achieve less top browning, press CHOICE BAKE® function, set
the desired temperature and press START.
On some models, if broiling while the time is counting down,
the set broiling temperature can be seen for 5 seconds by
pressing CUSTOM BROIL.
4. Press CANCEL when finished.
Broiling
Broiling uses direct radiant heat to cook food. Changing the
temperature when Custom Broiling allows more precise control
when cooking. The lower the temperature, the slower the
cooking. Thicker cuts and unevenly shaped pieces of meat, fish
and poultry may cook better at lower broiling temperatures.
BROILING CHART
For best results, place food 3 in. (7 cm) or more from the broil
element. Times are guidelines only and may need to be adjusted
for individual foods and tastes. Recommended rack positions are
numbered from the bottom (1) to the top (5). For diagram, see the
“Positioning Racks and Bakeware” section.
I
Use only the broiler pan and grid provided with the range. It is
designed to drain juices and help prevent spatter and smoke.
COOK
RACK
POSITION
TIME
I
For proper draining, do not cover the broiler grid with foil. The
bottom of the pan may be lined with aluminum foil for easier
cleaning.
FOOD
minutes
Side 1
Side 2
I
I
Trim excess fat to reduce spattering. Slit the remaining fat on
the edges to prevent curling.
Steak
1 in. (2.5 cm) thick
medium rare
medium
4
4
4
14-15
15-16
18-19
7-8
Pull out oven rack to the stop position before turning or
removing food. Use tongs to turn food to avoid the loss of
juices. Very thin cuts of fish, poultry or meat may not need to
be turned.
8-9
well done
9-10
*Ground meat patties
³ꢀ₄ in. (2 cm) thick
well done
I
After broiling, remove the pan from the oven when removing
the food. Drippings will bake on the pan if left in the heated
oven, making cleaning more difficult.
4
4
13-14
20-22
7-8
Pork chops
1 in. (2.5 cm) thick
10-11
Before broiling, position rack according to Broiling Chart. It is not
necessary to preheat the oven before putting food in unless
recommended in the recipe. Position food on grid in the broiler
pan, then place it in the center of the oven rack. Close the door to
the broil stop position to ensure proper broiling temperature.
Ham slice, precooked
¹ꢀ₂ in. (1.25 cm) thick
4
4
8-10
5-7
4-5
3-4
Frankfurters
Lamb chops
1 in. (2.5 cm) thick
4
14-17
8-9
Chicken
bone-in pieces
boneless breasts
3
4
17-20
11-16
17-20
11-16
Fish
- ¹ꢀ₂ in.
4
4
8-10
4-5
8-9
Fillets ¹ꢀ₄
(.6-1.25 cm) thick
- 1 in.
16-18
Steaks ³ꢀ₄
(2-2.5 cm) thick
*Place up to 9 patties, equally spaced, on broiler grid.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Warm Hold Feature
Timed Cooking
(on some models)
(on some models)
WARNING
WARNING
Food Poisoning Hazard
Food Poisoning Hazard
Do not let food sit in oven more than one hour
before or after cooking.
Do not let food sit in oven more than one hour
before or after cooking.
Doing so can result in food poisoning or
sickness.
Doing so can result in food poisoning or
sickness.
IMPORTANT: Food must be at serving temperature before
placing it in the warmed oven. Food may be held up to one hour,
however breads and casseroles may become too dry if left in the
oven during Warm Hold.
Timed Cooking allows the oven to be set to turn on at a certain
time of day, cook for a set length of time, and/or shut off
automatically. Delay start should not be used for food such as
breads and cakes because they may not bake properly.
Warm Hold Feature allows hot cooked foods to stay serving
temperature. It can also be used at the end of a timed cook.
Style 1 Series Electronic Oven Control (see “Electronic
Oven Controls” section)
To Use Automatic Warm Hold Feature:
At the end of a timed cook, either with or without a delayed start,
or at the end of a sequence program in which the last step is not
the Warm Hold mode, the oven will automatically default to a
1-hour warm hold mode at 170°F (77°C).
To Set a Timed Cook:
1. Press BAKE (optional).
2. Press the TEMP “up” or “down” arrow pads to enter a
temperature other than the one displayed.
When the cook time ends or the last step of the sequence is
complete, the display will show a warming countdown time.
When warming ends, the oven will automatically shut off and
“End” will appear on the display. Four tones will sound, and then
four 1-second reminder tones will sound every minute thereafter.
3. Press STOP TIME.
4. Press the HR and MIN “up” or “down” arrow pads to enter
the desired time to end cooking.
5. Press START. The display will count down the time.
To Disable Automatic Warm Hold: Press and hold WARM for 5
seconds. “Off” will appear in the 4-digit display. Repeat to turn
back on.
When the time ends, the oven will shut off automatically and
“End” will appear on the display. End-of-cycle tones will
sound, then, if enabled, reminder tones will sound every
minute.
When using the Automatic Warm Hold Feature, cook times may
need to be adjusted accordingly so that foods do not become
overcooked and dry.
6. Open and close the oven door to clear the display and/or
stop reminder tones.
To Use Manual Warm Hold Feature:
To Set a Delayed Timed Cook:
1. Press WARM.
Before setting, make sure the clock is set to the correct time of
2. Set the temperature (optional).
day. See “Clock” section.
Press the TEMP “up” or “down” arrow pad to raise or lower
the temperature in 5°F (3°C) amounts to set a temperature
other than 150°F (66°C). The warm range is 100°F-200°F
(38°C-93°C).
1. Press desired cook function.
2. Press the TEMP “up” or “down” arrow pads to enter a
temperature other than the one displayed.
3. Press START TIME or DELAY START TIME.
3. Press START.
4. Press the HR and MIN “up” or “down” arrow pads to enter
4. Press OFF/CANCEL when finished.
the time of day to start.
5. Press STOP TIME (optional).
6. If STOP TIME has been pressed, press the HR and MIN “up”
or “down” arrow pads to enter the desired time to end
cooking.
7. Press START. “DELAY” will appear on the display.
When the start time is reached, the oven will automatically
turn on. When the stop time is reached (if programmed), the
oven will shut off automatically and “End” will appear on the
display. End-of-cycle tones will sound, then, if on, reminder
tones will sound every minute.
8. Open and close the oven door to clear the display and/or
stop reminder tones.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
To Program the First Step of the Sequence:
1. Press FIRST/NEXT STEP.
Style 2 Series Electronic Oven Control (see “Electronic
Oven Controls” section)
“PROGRAM” and “STEP” will appear on the display. A
flashing “1” will also appear on the display, indicating that
step 1 is being programmed.
To Set a Timed Cook:
1. Press BAKE. The bake indicator light will light up.
2. Set the temperature (optional).
2.
Choose the desired cook function by pressing any cook
function key.
3. Press START TIME, then HR and MIN “up” or “down” arrow
3. Press the TEMP/TIME “up” or “down” arrow pad to enter a
pads to set the time of day for the first cook function to begin.
temperature other than the one displayed.
If START TIME is not pressed, then the sequence of cook
functions will begin immediately once programming is
complete and START is pressed.
4. Press COOK TIME. The cook time oven indicator light will
light up.
5. Press TEMP/TIME “up” or “down” arrow pad to enter the
The display will show either the time of day (if start time was
not programmed) or the start time (if same was programmed),
but with a flashing colon. “Stop” and “Time” will also appear
on the display.
length of time to cook.
6. Press START/ENTER. The display will count down the time.
When the time ends, the oven will shut off automatically and
“End” will appear on the display.
4. Press STOP TIME, then HR and MIN “up” or “down” arrow
7. Press OFF or open the oven door to clear the display.
pads to set the time of day for the first cook function to stop.
To Set a Delayed Timed Cook:
Before setting, make sure the clock is set to the correct time of
day. See “Clock” section.
To Program Next Steps of the Sequence:
1. Press FIRST/NEXT STEP.
“PROGRAM” and “STEP” will appear on the display. The
number of the steps being programmed will flash.
1. Press BAKE.
2. Set the temperature (optional).
“START” and “TIME” will appear on the display.
3. Press the TEMP “up” or “down” arrow pad to enter a
temperature other than the one displayed.
2. Choose the desired cook function by pressing any cook
function key.
4. Press COOK TIME. The cook time oven indicator light will
light up.
Press TEMP “up” or “down” arrow pad (if desired) to select
temperature.
5. Press the TEMP/TIME “up” or “down” arrow pad to enter the
length of time to cook.
3. Press STOP TIME, then HR and MIN “up” or “down” arrow
6. Press START TIME. The start time/delay oven indicator light
pads to select stop time.
will light up.
4. Press START to begin sequence.
7. Press the TEMP/TIME “up” or “down” arrow pad to enter the
5. Press OFF/CANCEL at any time to clear program and to stop
time of day to start.
program.
8. Press START/ENTER.
To Review/Modify Programmed Sequence:
When the start time is reached, the oven will automatically
turn on. The temperature and/or time settings can be
changed any time after pressing START/ENTER by repeating
steps 1-7. When the set cook time ends, the oven will shut off
automatically and “End” will appear on the display.
If program steps are partially or completely programmed, yet the
sequence has not been started, the programmed cook functions
can be reviewed.
1. Press REVIEW STEPS. Step 1 will appear in the display
9. Press OFF/CANCEL or open the oven door to clear the
Subsequent presses of REVIEW STEPS will cause display of
programmed steps in order.
display.
“STEP” and “RECALL” will appear on the display. The
number of the displayed step will flash. A recalled step will
remain lit on the display for 5 minutes if no further action is
taken.
Sequence Programming
(on some models)
Sequence Programming allows you to program at one time up to
four cook functions, and is usable with other electronic oven
control functions, such as the Timer and Warming Drawer.
2. If fewer than four steps have been programmed, press
REVIEW STEPS repeatedly until the last programmed step is
displayed, then press FIRST/NEXT STEP if it is desired to
program an additional step.
Sequence Programming takes precedence over any
nonsequenced cook function. For example, if an untimed Bake
function is in process and a sequence program is started, the
untimed Bake function will be canceled, and the program
sequence will start.
While a step is recalled, a cook function pad can be used to
change the function, or the TEMPERATURE “up” or “down”
arrow pad can be used to change the set temperature.
START TIME, when used with the HR or MIN “up” or “down”
arrow pads, can be used to change, add or delete a delayed
start.
All steps of a sequenced program must be programmed with a
stop time. If a stop time is not entered for a step in the sequence
program, and the FIRST/NEXT STEP pad is pressed, three tones
will sound.
STOP TIME can be used to change the stop time. Changing
the stop time of a step will automatically change the start
times and stop times of all subsequent programmed cook
functions.
3. After Review/Modification of the programmed sequence is
complete, press START to begin sequence.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
To Modify Sequence Programming:
1. Press UNDO.
To Use:
1. Place cooked food(s) in warming drawer.
The last step of the sequence will be canceled, and the step
prior to the canceled sequence will show on the display for
either review or modification.
2. Press WARMING DRAWER.
“dr Lo,” “DRAWER” and “START?” will appear on the display.
3. Press START.
If the programmed sequence has not been started, see “To
Program Next Steps of the Sequence” section to program a
step to replace the canceled cook function.
“DRAWER” and “ON” will appear on the display.
4. Press DRAWER OFF when finished.
2. Press START.
Warming Drawer Settings:
The first step will show on the display and the program
sequence will begin.
The warming drawer is pre-set for a “Lo” temperature, but can be
changed by pressing the TEMP “up” arrow pad. Use the
following chart as a guide when selecting a different temperature
other than “Lo.”
Changes can be made during a programmed cook function;
however, changes cannot be made after a programmed cook
function has been completed.
SETTINGS
TEMPERATURES
If at any time during an active sequenced program FIRST/
NEXT STEP is pressed, three tones will sound.
dr Lo (Low)
keeps soft rolls warm
100°F (38°C)
Warming Drawer
dr 2 (Medium Low)
dr 3 (Medium)
140°F (60°C)
160°F (71°C)
180°F (88°C)
195°F (91°C)
(on some models)
dr 4 (Medium High)
WARNING
dr HI (High)
keeps french fries crisp and
warm
Food Poisoning Hazard
Do not let food sit for more than one hour before
or after cooking.
Warming Drawer Temperature Chart
Doing so can result in food poisoning or
sickness.
Different foods require different settings in order to maintain the
ideal serving temperature. Use the following chart as a guide.
FOOD
SETTING
dr HI
The Warming Drawer is ideal for keeping hot cooked foods at
serving temperature. It may also be used for warming breads and
pastries.
Appetizers
Biscuits
Chicken
dr LO
Different types of food may be placed in the warming drawer at
the same time. For best results, do not hold foods longer than
one hour. For smaller quantities or heat-sensitive foods, such as
eggs, do not hold longer than 30 minutes.
Boneless, Breaded
Nuggets
dr HI
dr HI
Food must be at serving temperature before being placed in the
warming drawer. Breads, pastries, and fruit pies may be heated
from room temperature on the HI setting.
dr LO
dr HI
Coffee Cake
Dinner Plate (1)
Salisbury Steak, Mashed Potatoes, Corn
Remove food from plastic bags and place in oven-safe container.
Cover foods with a lid or aluminum foil.
Do not cover with plastic wrap.
Fish Pieces
Breaded
Battered
Empty serving dishes and oven proof dishes can be heated while
the warming drawer is preheating.
dr HI
dr HI
Before using the warming drawer, wash the tray that lines the
bottom of the drawer with soap and water. See “General
Cleaning” section.
dr HI
dr 4
French Fries
Gravy
The warming drawer comes with a liner that helps keep the
drawer clean.
dr 3
Ham, Boneless
Hard Rolls
Lasagna
Do not place food to be warmed directly on warming drawer liner.
dr LO
dr 4
Pastries
Prepackaged, baked
Prepackaged, frozen
dr 4
dr LO
Pie
Single Crust
Double Crust
dr LO
dr LO
17
Download from Www.Somanuals.com. All Manuals Search And Download.
I
I
Remove oven racks to keep them shiny and easy to slide.
FOOD
SETTING
dr 4
See “General Cleaning” section for more information.
Hand clean inside door edge and the 1½ in. (3.8 cm) area
around the inside oven cavity frame, being careful not to
move or bend the gasket. This area does not get hot enough
during self-cleaning to remove soil. Do not let water, cleaner,
etc. enter slots on door frame. Use a damp cloth to clean this
area.
Pizza
dr 4
Potatoes, Baked
Quiche
dr 3
dr 4
Roast, Boneless
Roasted Chicken
Soft Rolls
I
Wipe out any loose soil to reduce smoke and avoid damage.
At high temperatures, foods react with porcelain. Staining,
etching, pitting or faint white spots can result. This will not
affect cooking performance.
dr 4
dr LO
Prepare Cooktop and Storage Drawer:
I
Remove plastic items from the cooktop because they may
melt.
RANGE CARE
I
Remove all items from the storage drawer.
How the Cycle Works
Self-Cleaning Cycle
IMPORTANT: The heating and cooling of porcelain on steel in the
oven may result in discoloring, loss of gloss, hairline cracks and
popping sounds.
(on some models)
The Self-Cleaning cycle uses very high temperatures, burning soil
to a powdery ash.
WARNING
The oven is preset for a 3 hour 30 minute clean cycle, but the
time can be changed. Suggested clean times are 2 hours 30
minutes for light soil and between 3 hours 30 minutes and
4 hours 30 minutes for average to heavy soil.
Once the oven has completely cooled, remove ash with a damp
cloth. Do not wipe down any of the inside surfaces until the oven
has completely cooled down. Applying a cool damp cloth to the
inner door glass before it has completely cooled could result in
the glass breaking.
Burn Hazard
The oven light will not work during the Self-Cleaning cycle.
Do not touch the oven during the
Self-Cleaning cycle.
To Self-Clean:
Before self-cleaning, make sure the door is closed completely or
it will not lock and the cycle will not begin.
Keep children away from oven during
Self-Cleaning cycle.
1. Press AUTO CLEAN.
2. Press the HR and MIN “up” or “down” arrow pad, or the
TIME/TEMP “up” or “down” arrow pad to set a clean time
other than 3 hours 30 minutes.
Failure to follow these instructions can result
in burns.
On models with style 1 series electronic oven controls (see
“Electronic Oven Controls” section), the oven can be set to a
clean time between 3 hours 15 minutes and 5 hours 15
minutes.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off during the Self-Cleaning cycle. Exposure to
the fumes may result in death to certain birds. Always move birds
to another closed and well ventilated room.
On models with style 2 series electronic oven controls (see
“Electronic Oven Controls” section), the oven can be set to a
clean time between 2 hours 30 minutes and 4 hours 30
minutes.
Self-clean the oven before it becomes heavily soiled. Heavy soil
results in longer cleaning and more smoke.
Keep the kitchen well-ventilated during the Self-Cleaning cycle to
help get rid of heat, odors, and smoke.
3. Press START/ENTER.
Do not block the oven vent(s) during the Self-Cleaning cycle. Air
must be able to move freely. Depending on your model, see
“Oven Vent” or “Oven Vents” section.
The oven door will automatically lock. “LOCKED” will appear
on the display (on some models), and on other models, the
ON, HEAT and DOOR LOCKED indicator lights will light up.
The door will not unlock until the oven cools.
Do not clean, rub, damage or move the oven door gasket. The
door gasket is essential for a good seal.
When the cycle is complete and the oven cools, “End” will
appear on the oven display and “LOCKED” shown on the
display of some models will disappear. The indicator lights on
other models will go off.
Prepare Oven:
I
Remove the broiler pan, grid, cookware and bakeware and,
on some models, the temperature probe from the oven.
4. Press CANCEL or OFF/CANCEL, or open the oven door to
I
Remove any foil from the oven because it may burn or melt,
damaging the oven.
clear the oven display.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
To Delay Start Self-Clean (on some models):
CERAMIC GLASS (on some models)
Before delay starting Self-Clean, make sure the clock is set to the
correct time of day. See “Clock” section. Also, make sure the
door is closed completely or it will not lock and the cycle will not
begin.
Do not use steel wool, abrasive powder cleansers, chlorine
bleach, rust remover or ammonia because damage may occur.
Always wipe with a clean, wet cloth or sponge and dry thoroughly
to prevent streaking and staining.
1. Press AUTO CLEAN.
2. Press the HR “up” or “down” arrow pad to set a clean time
other than 3 hours 30 minutes. The clean time can be set
between 3 hours 15 minutes and 5 hours 15 minutes.
Cooktop Polishing Creme is recommended regularly to help
prevent scratches, pitting and abrasions and to condition the
cooktop, and can be ordered as an accessory. See “Assistance
or Service” to order.
3. Press START TIME.
4. Press the HR and MIN “up” or “down” arrows pads to enter
A Cooktop Scraper is also recommended for stubborn soils, and
can be ordered as an accessory. See “Assistance or Service” to
order. The Cooktop Scraper uses razor blades. Store razor
blades out of the reach of children.
the time of day to start.
5. Press START. The time of day is displayed.
The door will automatically lock and “LOCKED” and “DELAY”
will appear on the display. The door will not unlock until the
oven cools. When the start time is reached, the oven will
automatically turn on. When the cycle is complete and the
oven cools, “End” will appear on the lower oven display and
“LOCKED” will disappear.
Light to moderate soil
I
Paper towels or clean damp sponge:
Clean while the cooktop is still warm. You may want to wear
oven mitts while doing so.
6. Press any pad or open the oven door to clear the oven
Sugary spills (jellies, candy, syrup)
display.
I
Cooktop Scraper:
Clean while the cooktop is still warm. You may want to wear
oven mitts while doing so.
To Stop Self-Clean any time:
Press CANCEL or OFF. If the oven temperature is too high, “cln,”
“TIMED,” “ON,” “cool,” and “LOCKED” will appear on the display
(on some models), and the door will remain locked. It will not
unlock until the oven cools.
I
Cooktop Polishing Creme and clean damp paper towel:
Clean as soon as cooktop has cooled down. Rub creme into
surface with a damp paper towel or soft cloth. Continue
rubbing until white film disappears.
General Cleaning
Heavy soil, dark streaks, specks and discoloration
IMPORTANT: Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Always follow label instructions
on cleaning products.
I
Cooktop Polishing Creme or nonabrasive cleanser:
Rub product into soil with a damp paper towel or soft cloth.
Continue rubbing until white film disappears.
Soap, water and a soft cloth or sponge are suggested first unless
otherwise noted.
Burned-on soil
I
Cooktop Polishing Creme and Cooktop Scraper:
EXTERIOR PORCELAIN ENAMEL SURFACES
Rub creme into soil with damp paper towel. Hold scraper as
flat as possible on surface and scrape. Repeat for stubborn
spots. Polish entire cooktop with creme and paper towel.
(on some models)
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the entire appliance is cool. These spills
may affect the finish.
Metal marks from aluminum and copper
I
Cooktop Polishing Creme:
I
Glass cleaner, mild liquid cleaner or nonabrasive scrubbing
pad:
Clean as soon as cooktop has cooled down. Rub creme into
surface with a damp paper towel or soft cloth. Continue
rubbing until white film disappears. The marks will not totally
disappear but after many cleanings become less noticeable.
Gently clean around the model and serial number plate
because scrubbing may remove numbers.
Tiny scratches and abrasions
STAINLESS STEEL (on some models)
I
Cooktop Polishing Creme:
Rub creme into surface with a damp paper towel or soft
cloth. Continue rubbing until white film disappears. Scratches
and abrasions do not affect cooking performance and after
many cleanings become less noticeable.
Do not use soap-filled scouring pads, abrasive cleaners, Cooktop
Polishing Creme, steel-wool pads, gritty washcloths or some
paper towels. Damage may occur.
Rub in direction of grain to avoid damaging.
I
I
I
Stainless Steel Cleaner & Polish (not included):
See “Assistance or Service” section to order.
Liquid detergent or all-purpose cleaner:
Rinse with clean water and dry with soft, lint-free cloth.
Vinegar for hard water spots
COOKTOP CONTROLS
Do not use steel wool, abrasive cleansers or oven cleaner.
Do not soak knobs.
When replacing knobs, make sure knobs are in the OFF position.
On some models, do not remove seals under knobs.
I
Soap and water or dishwasher:
Pull knobs straight away from control panel to remove.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL PANEL
BROILER PAN AND GRID
Do not use abrasive cleaners, steel-wool pads, gritty washcloths
or some paper towels. Damage may occur.
Do not clean in the Self-Cleaning cycle.
I
Mildly abrasive cleanser:
I
Glass cleaner and soft cloth or sponge:
Scrub with wet scouring pad.
Apply glass cleaner to soft cloth or sponge, not directly on
panel.
I
Solution of ¹ꢀ₂ cup (125 mL) ammonia to 1 gal. (3.75 L) water:
Soak for 20 minutes, then scrub with scouring or steel-wool
pad.
COIL ELEMENTS (on some models)
I
Oven cleaner:
Do not clean or immerse in water. Soil will burn off when hot.
Follow product label instructions.
For more information, see “Coil Elements and Burner Bowls.”
Porcelain enamel only, not chrome
I
Damp cloth:
I
Dishwasher
Make sure control knobs are off and elements are cool.
STORAGE DRAWER (on some models)
BURNER BOWLS (on some models)
Make sure drawer is cool and empty before cleaning.
I
Solution of ¹ꢀ₂ cup (125 mL) ammonia to 1 gal. (3.75 L) water:
For more information, see “Storage Drawer” section.
Soak for 20 minutes, then scrub with stainless steel-wool
pad.
I
Mild detergent
Drawer Liner (on some models)
Remove all stored items from drawer and lift out drawer liner.
I
I
Oven cleaner:
Follow product label instructions.
Mildly abrasive cleanser:
Scrub with wet scouring pad.
I
Clean with mild detergent.
WARMING DRAWER and TRAY (on some models)
Porcelain enamel only, not chrome
Make sure drawer is cool and remove tray.
Mild detergent (for both)
I
Dishwasher
I
SURFACE UNDER COOKTOP (on some models)
Oven Light
Do not remove the cooktop to avoid product damage.
The oven light is a standard 40-watt appliance bulb. It will come
on when the oven door is open. It will not work during the Self-
Cleaning cycle. On some models, when the oven door is closed,
press OVEN LIGHT to turn it on or off.
For more information, see “Lift-up Cooktop” section.
I
Steel-wool pad
Before replacing, make sure the oven and cooktop are cool and
the control knobs are in the off position.
OVEN DOOR EXTERIOR
To replace:
I
Glass cleaner and paper towels or nonabrasive plastic
scrubbing pad:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
Apply glass cleaner to soft cloth or sponge, not directly on
panel.
counterclockwise to remove.
OVEN CAVITY
Do not use oven cleaners.
Food spills should be cleaned when oven cools. At high
temperatures, foods react with porcelain and staining, etching,
pitting or faint white spots can result.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb and bulb cover by turning clockwise.
5. Plug in range or reconnect power.
I
I
I
Self-Cleaning cycle:
See “Self-Cleaning Cycle” first.
OVEN RACKS AND ROASTING RACKS
Self-Cleaning cycle:
See “Self-Cleaning Cycle” first. Remove racks or they will
discolor and become harder to slide. If this happens, a light
coating of vegetable oil applied to the rack guides will help
them slide.
Steel-wool pad
20
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Tilt top of door toward range. Slide hinge hangers down onto
front frame support pins. Make sure the hinge hangers are
fully seated and engaged on the support pins.
Oven Door
For normal range use, it is not suggested to remove the oven
door. However, if necessary, follow these instructions. The oven
door is heavy.
Before Removing:
1. Use a putty knife or screwdriver and insert it at the bottom
corner of the door stop clip.
4. Insert the door stop clip with the angular surface at the top of
the frame hinge slot, then push in the bottom of the clip until
flanges are flush with the front frame.
2. Pry door stop clip free and remove from front frame hinge
slot. Take care not to scratch finish.
3. Repeat procedure for other door stop clip.
To Remove:
5. Open the door completely and remove the door removal pins.
Save door removal pins for future use.
1. Open the oven door. Insert door removal pins, included with
your range, into both hinge hangers. Do not remove the pins
while the door is removed from the range.
6. Close the door.
Storage Drawer
The storage drawer can be removed. Before removing, make sure
drawer is cool and empty.
To Remove:
1. Pull drawer straight out to the first stop.
2. Lift up the back of the drawer and pull out.
2. Carefully close the door until it rests against the door removal
To Replace:
pins.
1. Fit the ends of the drawer rails into the guides in the cavity.
3. Grasp the door on the sides with your fingers on the front of
2. Slide the drawer closed.
the door and your thumbs on the inside surface.
4. Pull door straight up, then toward you. Hinge hangers will
slide out of front frame hinge slot. Do not remove door
removal pins until the door is replaced on the range.
Warming Drawer
(on some models)
Remove all items from inside the warming drawer, and allow the
unit to cool completely before attempting to remove the drawer.
To Remove:
1. Open drawer to its full open position.
2. Locate the black triangle-shaped tabs on both sides of the
drawer.
1
1. Tab
3. Press the tab down on the right side, and lift tab up on the left
To Replace:
side at the same time, then pull drawer out another inch.
1. Grasp the door on the sides with your fingers on the front of
the door and your thumbs on the inside surface.
2. Hold oven door so that the top edge of each hinge hanger is
horizontal. Insert hinge hangers into the front frame hinge
slots.
4. Holding the drawer by its sides, not its front, carefully pull it
all the way out.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
To Replace:
Oven will not operate
1. Align the drawer glides with the receiving guides.
I
I
I
Is the electronic oven control set correctly?
See “Electronic Oven Control” section.
Has a delay start been set?
See “Timed Cooking” section.
On some models, is the Control Lock set?
See “Control Lock” section.
2. Push drawer in all the way.
3. Gently open and close the drawer to ensure it is seated
Oven temperature too high or too low
properly on the slides.
I
I
Does the oven temperature calibration need adjustment?
See “Oven Temperature Control” section.
TROUBLESHOOTING
On some models, does the cooling fan run during BAKE,
BROIL or CLEAN?
It is normal for the fan to automatically run when the oven is
in use. These helps cool the electronic control.
Try the solutions suggested here first in order to avoid the cost of
an unnecessary service call.
Nothing will operate
Oven indicator lights flash
I
I
Is the power supply cord unplugged?
I
Do the oven indicator lights flash?
Plug into a grounded outlet.
See the “Oven Indicator Lights” section. If the indicator
light(s) keeps flashing, call for service. See “Assistance or
Service” section.
Has a household fuse been blown or has the circuit
breaker been tripped?
Replace the fuse or reset the circuit.
Display shows messages
Cooktop will not operate
I
I
Is the display showing “PF”?
I
I
Is the control knob set correctly?
There has been a power failure. Clear the display. See
“Display(s)” section. On some models, reset the clock, if
needed. See “Clock” section.
Push in knob before turning to a setting.
On ceramic glass models, is the “Cooktop Lockout” set?
See “Cooktop Lockout” section.
Is the display showing a letter followed by a number?
Depending on your model, press OFF/CANCEL, OFF or
CANCEL/OFF to clear the display. See “Display(s)” section. If
it reappears, call for service. See “Assistance or Service”
section.
Excessive heat around cookware on cooktop
I
Is the cookware the proper size?
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than 1 in. (2.5 cm) outside the cooking area.
Self-Cleaning cycle will not operate
I
I
I
Is the oven door open?
Close the oven door all the way.
Hot Surface indicator light stays on
Has the function been entered?
See “Self-Cleaning Cycle” section.
I
Does the Hot Surface indicator light stay on after control
knob(s) have been turned off?
See “Cooktop Controls” section.
On some models, has a delay start Self-Clean cycle been
set?
See “Self-Cleaning Cycle” section.
Cooktop cooking results not what expected
I
Has a delay start been set?
See “Timed Cooking” section.
I
I
I
Is the proper cookware being used?
See “Cookware” section.
Is the control knob set to the proper heat level?
See “Cooktop Controls” section.
Is the appliance level?
Level the appliance. See the Installation Instructions.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Oven cooking results not what expected
In the U.S.A.
Call the Whirlpool Customer Interaction Center
I
I
I
I
I
I
I
I
I
I
Is the appliance level?
Level the appliance. See the Installation Instructions.
toll free: 1-800-253-1301.
Our consultants provide assistance with:
Is the proper temperature set?
I
I
I
I
I
Features and specifications on our full line of appliances.
Double-check the recipe in a reliable cookbook.
Installation information.
Is the proper oven temperature calibration set?
See “Oven Temperature Control” section.
Use and maintenance procedures.
Accessory and repair parts sales.
Was the oven preheated?
See “Baking and Roasting” section.
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
Is the proper bakeware being used?
See “Bakeware” section.
I
Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool designated service technicians
are trained to fulfill the product warranty and provide after-
warranty service, anywhere in the United States.
Are the racks positioned properly?
See “Positioning Racks and Bakeware” section.
Is there proper air circulation around bakeware?
See “Positioning Racks and Bakeware” section.
To locate the Whirlpool designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
Is the batter evenly distributed in the pan?
Check to make sure batter is level in the pan.
Is the proper length of time being used?
Adjust cooking time.
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
Has the oven door been opened while cooking?
Oven peeking releases oven heat and can result in longer
cooking times.
Whirlpool Brand Home Appliances
Customer Interaction Center
553 Benson Road
I
I
Are baked items too brown on the bottom?
Move rack to higher position in the oven.
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Are pie crust edges browning early?
Use aluminum foil to cover the edge of the crust and/or
reduce baking temperature.
Accessories U.S.A.
To order accessories, call the Whirlpool Customer Interaction
Center toll free at 1-800-442-9991 and follow the menu prompts.
Accessories Online.”
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
Canning Unit Kit
(coil element models)
Order Part #242905
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
Cooktop Polishing Creme
(ceramic glass models)
Order Part #4392916
If you need replacement parts
If you need to order replacement parts, we recommend that you
only use FSP® replacement parts. FSP® replacement parts will fit
right and work right because they are made with the same
precision used to build every new WHIRLPOOL® appliance.
To locate FSP® replacement parts in your area, call our Customer
Interaction Center telephone number or your nearest Whirlpool
designated service center.
Cooktop Scraper
(ceramic glass models)
Order Part #3183488
Stainless Steel Cleaner & Polish
(stainless steel models)
Order Part #4396095
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WHIRLPOOL® COOKTOP, BUILT-IN OVEN AND RANGE WARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation will pay for FSP® replacement parts and repair labor to correct defects in materials or
workmanship. Service must be provided by a Whirlpool Corporation designated service company.
SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CLEANTOP® COOKTOP
On ceramic glass ranges and ceramic glass cooktops, in the second through fifth years from the date of purchase, when this appliance
is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation will pay for FSP®
replacement parts for the CLEANTOP® ceramic glass cooktop.
Whirlpool Corporation warrants that the ceramic glass cooktop will not discolor, the cooktop pattern will not wear off, the rubber seal
between the ceramic glass cooktop and porcelain edge will not crack, the ceramic glass cooktop will not crack due to thermal shock
and the surface unit elements will not burn out.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to replace house fuses or
correct house wiring, or to replace owner-accessible light bulbs.
2. Repairs when your appliance is used in other than normal, single-family household use.
3. Pickup and delivery. Your appliance is designed to be repaired in the home.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God or use of products not
approved by Whirlpool Corporation.
5. Repairs to CLEANTOP®
ceramic glass cooktop or other surfaces if they have not been cared for as recommended in the Use and
Care Guide.
6. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
7. Replacement parts or repair labor costs for units operated outside the United States.
8. Any labor costs during the limited warranty period.
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not
apply to you. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
Outside the 50 United States, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if another
warranty applies.
If you need service, first see the “Troubleshooting” section of this book. After checking “Troubleshooting,” additional help can be found
by checking the “Assistance or Service” section or by calling the Whirlpool Customer Interaction Center, 1-800-253-1301 (toll-free),
from anywhere in the U.S.A.
5/00
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your appliance to
better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label/plate, located on your appliance as shown in the
“Parts and Features” section.
Dealer name____________________________________________________
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
9756384
© 2003 Whirlpool Corporation.
6/03
Printed in U.S.A.
All rights reserved.
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|