®
Model No. WESY99300
Serial No.
USER’S MANUAL
The serial number is found in the
location shown below. Write the
serial number in the space above.
Serial
Number
Decal
QUESTIONS?
We are committed to providing
complete customer satisfaction.
If you have questions, or if there
are missing parts, we will guar-
antee complete satisfaction
through direct assistance from
our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUS-
TOMER HOT LINE. The trained
technicians on our customer hot
line will provide immediate
assistance, free of charge.
CUSTOMER HOT LINE:
1-888-936-4266
Mon.–Fri., 8 a.m.–6:30 p.m. EST
(excluding holidays)
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.
Visit our website at
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the weight system.
1. Read all instructions in this manual and in
the accompanying literature before using the
weight system.
12. Never release the press arm, butterfly arms,
leg lever, lat bar, or nylon strap while weights
are raised. The weights will fall with great
force.
2. It is the responsibility of the owner to ensure
that all users of the weight system are ade-
quately informed of all precautions.
13. Always disconnect the lat bar or nylon strap
from the weight system when performing an
exercise that does not use the attachments.
3. The weight system is intended for home use
only. Do not use the weight system in a com-
mercial, rental, or institutional setting.
14. The warning decals shown below have been
attached to the weight system in the loca-
tions shown. If a decal is missing or illegible,
please call our Customer Service Department
at the number on the front cover of this man-
ual to order a free replacement decal. Apply
the new decal in the appropriate location.
4. Use the weight system only on a level sur-
face. Cover the floor or carpet beneath the
weight system to protect the floor or carpet.
5. Regularly inspect and tighten all parts.
Replace any worn parts immediately.
6. Make sure that the cables remain on the pul-
leys at all times. If the cables bind while you
are exercising, stop immediately and make
sure that the cables are on all of the pulleys.
7. Keep children under the age of 12 and pets
away from the weight system at all times.
8. Always wear athletic shoes for foot protec-
tion while exercising.
9. Keep hands and feet away from moving parts.
10. Always stand on the foot plate when perform-
ing an exercise that could cause the weight
system to tip.
11. If you feel pain or dizziness while exercising,
stop immediately and begin cooling down.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the innovative and versatile
WEIDER® PRO 9930 weight system. The WEIDER®
PRO 9930 offers a unique selection of weight stations
designed to develop every major muscle group of the
body. Whether your goal is to tone your body, build
dramatic muscle size and strength, or improve your
cardiovascular system, the WEIDER® PRO 9930 will
help you to achieve the results you want.
questions, please contact our Customer Service
Department toll-free at 1-888-936-4266, Mon.–Fri., 8
a.m.–6:30 p.m. EST (excluding holidays). To help us
assist you, please note the product model number and
serial number before calling. The model number is
WESY99300. The serial number can be found on a
decal attached to the weight system (see the front
cover of this manual).
For your benefit, read this manual carefully before
using the weight system. If you have additional
Please use the drawing below to familiarise your-
self with the major parts of the weight system.
Lat Bar
ASSEMBLED
DIMENSIONS:
Height: 198 cm
Width: 165 cm
Depth: 86 cm
High Pulley
Station
Butterfly
Arms
Backrest
Backrest
Curl Pad
Press Arm
Adjustment
Knob
Seat
Low Pulley
Station
Leg Press
Lever
Weight
Stack
Foot Plate
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Make sure you have the following tools:
• Two adjustable wrenches
Make Assembly Easier for Yourself
Everything in this manual is designed to
ensure that the weight system can be assem-
bled successfully by anyone. Before begin-
ning assembly, make sure to read the
information on this page. This brief intro-
duction will save you much more time than
it takes to read it.
• One standard screwdriver
• One phillips screwdriver
• One rubber mallet
• You will also need grease or petroleum jelly, a
small amount of soapy water, and clear tape or
masking tape.
Assembly Requires Two Persons
Note: Assembly will be more convenient if you have
a socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
For your convenience and safety, assemble the
weight system with the help of another person.
Set Aside Enough Time
How to Identify Parts
Due to the many features of the weight system, the
assembly process will require about six hours. By
setting aside plenty of time and by deciding to
make the task enjoyable, assembly will go smoothly.
You may want to assemble the weight system over
a couple of evenings.
To help you identify the small parts used in assembly,
we have included a PART IDENTIFICATION CHART
in the center of this manual. Place the chart on the
floor and use it to easily identify parts during each
assembly step. Note: Some small parts may have
been pre-attached. If a part is not in the parts
bag, check to see if it has been pre-attached.
Select a Location for the Weight System
How to Orient Parts
Because of its weight and size, the weight system
should be assembled in the location where it will be
used. Make sure that there is enough room to walk
around the weight system as you assemble it.
As you assemble the weight system, make sure that
all parts are oriented exactly as shown in the draw-
ings.
How to Unpack the Box
Tightening Parts
To make assembly as easy as possible, we have
divided the assembly process into four stages. The
parts needed for each stage are found in individual
bags. Important: Wait until you begin each stage
to open the parts bag for that stage. Place all
parts of the weight system in a cleared area and
remove the packing materials. Do not dispose of
the packing materials until assembly is completed.
Tighten all parts as you assemble them, unless
instructed to do otherwise.
Questions?
If you have questions after reading the assembly
instructions, please call our Customer Service
Department at 1-888-936-4266.
The Four Stages of the Assembly Process
Frame Assembly—You will begin by assembling
the base and the uprights that form the skeleton of
the weight system.
Cable Assembly—During this stage you will
attach the cables and pulleys that connect the
arms to the weights.
Arm Assembly—During this stage you will
Seat Assembly—During the final stage you will
assemble the arms and the leg lever.
assemble the seats and the backrests.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Frame Assembly
38
19
1. Before beginning, make sure that you have read
20
60
and understood the information on page 5.
2
1
Locate and open the parts bag labelled “FRAME
ASSEMBLY.”
61
38
2
Press a 2” Square Inner Cap (38) into the Butterfly
Base (61). Press two 2” Square Inner Caps into the
Press Base (60).
1
1
1
38
Insert four 5/16” x 2 1/2” Carriage Bolts (1) up
through the indicated holes in the Butterfly Base (61)
and the Press Base (60). Note: If the Bolts fall out,
secure them by putting a small piece of tape over
the head of each Bolt. Place the Butterfly Base and
the Press Base flat on the floor.
2
Attach the Press Base (60) to the Butterfly Base (61)
with two 5/16” x 2 3/4” Bolts (20), two 5/16” Flat
Washers (19), and two 5/16” Nylon Locknuts (2).
Position
with the
bracket
on this
side
2. Position the Butterfly Upright (62) as shown. Place
the bracket on the lower end of the Butterfly Upright
over the indicated 5/16” x 2 1/2” Carriage Bolts (1) in
the Butterfly Base (61). Hand tighten two 5/16” Nylon
Locknuts (2) onto the Bolts. Do not tighten the
NylonLocknuts yet.
Place the bracket on the lower end of the Press
Frame Upright (59) over the indicated 5/16” x 2 1/2”
Carriage Bolts (1) in the Press Base (60). Hand tight-
en two 5/16” Nylon Locknuts (2) onto the Bolts. Do
not tighten the Nylon Locknuts yet.
59
62
2
2
1
1
61
60
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Place two Weight Bumpers (84) over the indicated
holes in the Butterfly Base (61). Slide the Weight
Guides (58) into the indicated holes.
3
58
8
Attach the Weight Guides (58) to the Butterfly Base
(61) with two 3/8” x 2 1/2” Bolts (6), four 3/8” Flat
Washers (17), and two 3/8” Jam Nuts (18).
Pin
Grooves
Slide the eight Weights (8) onto the Weight Guides
(58). Make sure that the Weights are turned so the
pin grooves are on the bottoms of the Weights.
84
18
17
18
17
61
17
6
4. Press a Weight Tube Bumper (76) into the lower end
of the Weight Tube (77). Slide the Weight Tube into
the center hole in the Weights (8).
4
Lubricate
78
58
Lubricate the holes in the Top Weight (78). Slide the
Top Weight onto the Weight Guides (58).
77
76
8
5. Press two 2” Square Inner Caps (38) into the Butterfly
Top Frame (64). Press two 1” Round Inner Caps (41)
into the top of the Butterfly Top Frame.
5
38
19
20
19
2
Attach the Butterfly Top Frame (64) to the Press Top
Frame (63) with two 5/16” x 2 3/4” Bolts (20), two
5/16” Flat Washers (19), and two 5/16” Nylon
Locknuts (2).
64
41
38
63
2
38
Press a 2” Square Inner Cap (38) into the Press Top
Frame (63).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Attach the Butterfly Top Frame (64) and the Press
Top Frame (63) to the indicated brackets on the
Uprights (59, 62) with four 5/16” x 2 3/4” Bolts (20),
two Top Plates (46), and four 5/16” Nylon Locknuts
(2). Note: Before attaching the Top Frames to the
Uprights, make sure that both Weight Guides (58)
are inside of the indicated holes. Do not tighten
the NylonLocknuts yet.
6
18
20
20
17
17
17
17
46
63
46
64
Holes
6
Secure the Weight Guides (58) to the Butterfly Top
Frame (64) with two 3/8” x 2 1/2” Bolts (6), four 3/8”
Flat Washers (17), and two 3/8” Jam Nuts (18).
58
2
2
59
62
7. Turn the Seat Brace (75) so the nut is on the side
shown. Attach the Seat Brace to the Butterfly Base
(61) with the indicated 5/16” x 2 1/2” Carriage Bolts
(1) and two 5/16” Nylon Locknuts (2). Do not tighten
the NylonLocknuts yet.
7
Nut
75
2
1
61
8. Hold the Seat Bar (74) between the Seat Brace (75)
and the Butterfly Upright (62) so that the hole that is
closest to a welded plate is toward the Seat Brace.
Attach the Seat Bar to the Seat Brace with two 5/16”
x 2 3/4” Bolts (20), two 5/16” Flat Washers (19), and
two 5/16” Nylon Locknuts (2). Do not tighten the
Nylon Locknuts yet. Note: Be careful not to over-
tighten the Nylon Locknuts, or the curl post
attached in step 38 will not slide freely.
8
62
19
2
20
Hole
19
74
19
Attach the Seat Bar (74) to the Butterfly Upright (62)
with two 5/16” x 2 3/4” Bolts (20), two 5/16” Flat
Washers (19), and two 5/16” Nylon Locknuts (2).
75
20
Tighten all nylon locknuts used in steps 1
through 8.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Arm Assembly
53
9. Locate and open the parts bag labelled “ARM
30
ASSEMBLY.”
Lubricate
4
Press a 1” x 7/8” Plastic Bushing (29) onto each weld-
ed spacer on the Press Frame (53). Slide the Press
Frame onto the Press Base (60). (See the inset draw-
ing for proper orientation.) Note: The Plastic
Bushings should fit onto the ends of the tube in
the Press Base. This will be a tight fit.
29
53
Tube
60
Lubricate the 3/8” x 8” Bolt (30). Attach the Press
Frame (53) to the Press Base (60) with the Bolt and a
3/8” Nylon Locknut (4). Do not overtighten the Nylon
Locknut; the Press Frame must pivot easily.
10
37
80
10. Press a 1 3/4” Square Inner Cap (37) into the top of a
Press Arm (54). Press a 1” Inner Cap (80) into the
indicated hole in the Press Arm.
37
Attach the Press Arm (54) to the bracket on the Press
Frame (53) with two 5/16” x 2 1/2” Bolts (3) and two
5/16” Nylon Locknuts (2).
54
80
Repeat this step to assemble the second Press Arm
(54).
2
3
53
11. Press a 1 1/2” Square Inner Cap (79) into the Press
Seat Frame (52).
11
20
2
Slide the bracket on the lower end of the Press Seat
Frame (52) onto the indicated 5/16” x 2 1/2” Carriage
Bolts (1) in the Press Base (60). Tighten two 5/16”
Nylon Locknuts (2) onto the Bolts.
59
52
79
19
Attach the Press Seat Frame (52) to the Press Frame
Upright (59) with two 5/16” x 2 3/4” Bolts (20), two
5/16” Flat Washers (19), and two 5/16” Nylon
Locknuts (2).
2
2
19
60
1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Press two 1 1/2” Square Inner Caps (79) into the Leg
Lever (49). Insert a Bumper (33) between the brackets
on the Leg Lever. Attach the Bumper to the Leg Lever
with a #10 x 1” Screw (32).
12
52
81
90
Slide the bracket on the Leg Lever (49) onto the Press
Seat Frame (52). Attach the Leg Lever to the Press Seat
Frame with a 5/16” x 2 1/4” Bolt (81) and a 5/16” Jam
Nut (90). Do not overtighten the Jam Nut. The Leg
Lever must pivot easily.
32
79
49
79
33
17
83
4
Attach a 3/8” x 2 1/2” Eyebolt (83) to the Leg Lever (49)
with a 3/8” Flat Washer (17) and 3/8” Nylon Locknut (4).
13. Press a 1 3/4” Square Inner Cap (37) into each end of
the Right Butterfly Arm (68). Wet the lower end of the
Arm with soapy water. Slide a 10” Pad (65) onto the
lower end of the Arm.
13
64
Lubricate
Lubricate the indicated axle on the Butterfly Top Frame
(64). Have a second person slide the Right Butterfly Arm
(68) onto the axle, as shown. Refer to the inset draw-
ing. Place two 1” Retainers (25), with the teeth down-
ward, on top of an inverted 1” Round Cap (26). Using
a hammer, tap the 1” Round Cap and the Retainers
onto the axle to secure the Right Butterfly Arm.
25
26
37
68
67
Repeat this step to assemble the Left Butterfly Arm (67).
37
65
64
25
Teeth
26
Cable Assembly
14. Open the parts bag labelled “CABLE ASSEMBLY
AND PULLEYS.” For cable identification and routing
during steps 14–32, refer to the CABLE DIAGRAMS
and CABLE ID CHART on pages 19 and 20.
Insert two 3/8” x 1” Bolts (15) into the welded brackets
on the Left and Right Butterfly Arms (67, 68). Secure
each Bolt with a 3/8” Jam Nut (18).
14
15
15
Identify the Short Cable (71). It has a closed loop on
each end. Slide one end of the Cable onto each of the
3/8” x 1” Bolts (15). Secure the Cable to the Bolts with
3/8” Jam Nuts (18). Do not overtighten the Jam Nuts.
68
18
71
18
5
67
Remove both 3 1/2” Pulleys (5) from the pre-assembled
Adjustable Pulley Plates (44). Wrap the Short Cable (71)
around a Pulley in the direction shown. Attach the Pulley
and a Cable Trap (39) to the top hole in the two
Adjustable Pulley Plates with a 3/8” x 2” Bolt (35) and a
3/8” Nylon Locknut (4). Make sure that the Cable Trap
and the Pulley Plates are oriented as shown.
35
39
4
44
10
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Wrap the Short Cable (71) over a “V” Pulley (21) as
shown. Attach the “V” Pulley and a Long Cable Trap
(14) to one side of the welded bracket on the Butterfly
Upright (62) with a 3/8” x 2 1/2” Bolt (6) and a 3/8”
Nylon Locknut (4).
15
21
6
14
Wrap the Short Cable (71) over another “V” Pulley
(21), and attach the “V” Pulley and a Long Cable Trap
(14) to the other side of the welded bracket on the
Butterfly Upright (62) in the same manner.
4
21
6
62
Welded
Bracket
14
71
16. Identify the Medium Cable (72). It has a ball on
one end and a threaded shaft on the other. Wrap
the Medium Cable over a 3 1/2” Pulley (5) as shown.
Attach the Pulley to the Press Top Frame (63) with a
3/8” x 3 1/2” Bolt (24), a 3/8” Flat Washer (17), and a
3/8” Jam Nut (18).
16
17
18
63
24
5
Make sure that the Medium Cable (72) is between
the 3 1/2” Pulley (5) and the welded pin on the
Press Top Frame (63).
72
Pin
17
18
17. Note: It may be helpful to loosen the indicated
5/16” Nylon Locknuts (2) before beginning this
step.
7
5
39
Wrap the Medium Cable (72) over a 3 1/2” Pulley (5)
as shown. Attach the Pulley and a Cable Trap (39) to
the Press Top Frame (63) with a 3/8” x 3 3/4” Bolt (7).
72
2
63
18. Route the threaded shaft on the Medium Cable (72)
under one of the 3 1/2” Pulleys (5) that are already
mounted in the Double “U”-Bracket (36). Tighten the
3/8” x 1 3/4” Bolt (22).
72
5
22
36
11
Download from Www.Somanuals.com. All Manuals Search And Download.
19. Wrap the Medium Cable (72) over a 4 1/2” Pulley
(34) in the direction shown. Attach the Pulley to the
Butterfly Top Frame (64) with a 3/8” x 1 3/4” Bolt (22)
and a 3/8” Nylon Locknut (4).
19
64
4
22
34
72
20. Attach the threaded shaft on the Medium Cable (72)
to the Small “U”-Bracket (43) with a 1/4” Flat Washer
(11) and a 1/4” Nylon Locknut (16). Note: See the
inset drawing. Do not completely tighten the
Nylon Locknut; it should be threaded only two
turns onto the end of the Cable.
20
72
2
43
11
16
9
Attach the Small “U”-Bracket (43) to the Weight Tube
(77) with a 5/16” x 1 3/4” Bolt (9) and a 5/16” Nylon
Locknut (2).
77
72
11
43
16
21. Identify the Long Cable (73). It has a ball on one
end and a loop on the other. Route the end with the
loop through the slot in the cable guide on the
Butterfly Base (61).
21
Route the Long Cable (73) under a 3 1/2” Pulley (5)
as shown. Attach the Pulley and a Cable Trap (39) to
the indicated bracket on the Butterfly Base (61) with a
3/8” x 2” Bolt (35) and a 3/8” Nylon Locknut (4). Make
sure the Cable Trap is oriented as shown.
61
5
4
Cable
Guide
35
39
73
12
Download from Www.Somanuals.com. All Manuals Search And Download.
22. Wrap the Long Cable (73) around a 3 1/2” Pulley (5)
in the direction shown. Attach the Pulley and a Cable
Trap (39) to the Butterfly Upright (62) with a 3/8” x
3 3/4” Bolt (7), a 3/8” Flat Washer (17), and a 3/8”
Nylon Locknut (4). Make sure that the Cable Trap is
oriented as shown.
22
35
44
4
39
Wrap the Long Cable (73) over a 3 1/2” Pulley (5) in
the direction shown. Re-attach the Pulley and a Cable
Trap (39) to the lower hole in the Adjustable Pulley
Plates (44) with a 3/8” x 2” Bolt (35) and a 3/8” Nylon
Locknut (4). Make sure that the Cable Trap is ori-
ented as shown.
5
62
4
17
5
7
39
73
23. Wrap the Long Cable (73) around a 3 1/2” Pulley (5)
in the direction shown. Attach the Pulley and a Cable
Trap (39) to the indicated bracket on the Butterfly
Base (61) with a 3/8” x 2” Bolt (35) and a 3/8” Nylon
Locknut (4).
23
73
35
5
61
39
Bracket
4
24. Wrap the Long Cable (73) around a 3 1/2” Pulley (5).
Attach the Pulley and a Cable Trap (39) to the indicat-
ed bracket on the Butterfly Base (61) with a 3/8” x 2”
Bolt (35) and a 3/8” Nylon Locknut (4).
24
73
39
35
5
4
Bracket
61
13
Download from Www.Somanuals.com. All Manuals Search And Download.
25. Note: For clarity, this and the following drawings
25
show some parts removed.
Remove the lower 3 1/2” Pulley (5) from the Double
“U”-Bracket (36). Wrap the Long Cable (73) over the
Pulley in the direction shown. Attach the Pulley to the
Double “U”-Bracket with a 3/8” x 1 3/4” Bolt (22) and
a 3/8” Nylon Locknut (4). Make sure that the Double
“U”-Bracket is oriented as shown.
4
5
36
22
73
26. Wrap the Long Cable (73) around a 3 1/2” Pulley (5)
in the direction shown. Attach the Pulley and a Cable
Trap (39) to the indicated bracket on the Press Base
(60) with a 3/8” x 2” Bolt (35) and a 3/8” Nylon
Locknut (4). Make sure that the Cable Trap is ori-
ented as shown.
26
73
35
5
39
4
60
27. Wrap the Long Cable (73) around the 3 1/2” Pulley
(5) in the direction shown. Attach the Pulley and a
Cable Trap (39) to the Press Frame Upright (59) with
a 3/8” x 4 3/4” Bolt (23). Hand tighten a 3/8” Nylon
Locknut (4) two turns onto the Bolt. In step 31, anoth-
er Pulley will be attached to the Bolt.
27
59
73
23
5
39
4
28. Wrap the Long Cable (73) around a 3 1/2” Pulley (5)
in the direction shown. Attach the Pulley and a Cable
Trap (39) to the indicated hole in the Press Frame
(53) with a 3/8” x 3 1/4” Bolt (28), a 3/8” Flat Washer
(17), and a 3/8” Nylon Locknut (4). Make sure that
the Pulley is mounted on the inside of the Press
Frame and that the Cable Trap is oriented as
shown.
28
28
53
17
73
4
39
5
14
Download from Www.Somanuals.com. All Manuals Search And Download.
29. Wrap the Long Cable (73) around a “V” Pulley (21) in
the direction shown. Attach the “V” Pulley and a Long
Cable Trap (14) to the small tube on the Press Seat
Frame (52) with a 3/8” x 3 1/4” Bolt (28), a 3/8” Flat
Washer (17), and a 3/8” Nylon Locknut (4). Note: The
small tube has three adjustment holes. Mount the
“V” Pulley in the hole farthest from the Press
Frame Upright (59). Make sure that the Cable Trap
is oriented as shown.
29
59
52
4
17
14
21
28
73
30. Wrap the Long Cable (73) around a 3 1/2” Pulley (5)
in the direction shown. Attach the Pulley and a Cable
Trap (39) to the indicated hole in the Press Frame
(53) with a 3/8” x 3 1/4” Bolt (28), a 3/8” Flat Washer
(17), and a 3/8” Nylon Locknut (4). Make sure that
the Pulley is mounted on the inside of the Press
Frame and that the Cable Trap is oriented as
shown.
30
73
4
17
28
5
39
53
31. Route the Long Cable (73) around a 3 1/2” Pulley (5)
and back through the opening in the Press Frame
(53).
31
39
Remove the 3/8” Nylon Locknut (4) from the 3/8” x
4 3/4” Bolt (23) that was inserted in step 27. Attach
the Pulley and a Cable Trap (39) to the Bolt and
secure them with the Nylon Locknut. Make sure that
the Cable Trap is oriented as shown.
53
23
5
4
73
32. Note: Lift the Top Weight (78) on the weight stack
in order to create slack in the Long Cable (73)
before beginning this step.
32
Attach the Long Cable (73) to the Leg Lever (49) by
slipping the looped end of the Cable onto the looped
end of the 3/8” x 2 1/2” Eyebolt (83).
49
83
73
15
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Seat Assembly
51
33. Locate and open the parts bag labelled “SEAT
ASSEMBLY.”
Insert a 1/4” x 2” Carriage Bolt (85) into the center
hole in a Seat Plate (42). Attach the Seat Plate to a
Seat (51) with two 1/4” x 3/4” Screws (13).
85
42
13
11
86
Insert the 1/4” x 2” Carriage Bolt (85) into the indicat-
ed hole in the Press Seat Frame (52) and secure it
with a 1/4” Flat Washer (11) and a 1/4” Nylon Locknut
(16). Secure the other end of the Seat (51) with a 1/4”
x 2” Bolt (86) and a 1/4” Flat Washer.
52
11
16
34. Press four 3/4” Round Inner Caps (40) into the ends
of the Pad Tubes (48).
34
Insert the Pad Tubes (48) into the indicated holes in
the Leg Lever (49) and the Press Seat Frame (52).
Slide Foam Pads (47) onto the ends of both Pad
Tubes.
40
52
47
48
40
47
49
35. Insert a 1/4” x 2 1/2” Carriage Bolt (12) into the center
hole in a Seat Plate (42). Attach the Seat Plate to the
Press Backrest (89) with two 1/4” x 3/4” Screws (13).
35
10
89
Insert the 1/4” x 2 1/2” Carriage Bolt (12) into the indi-
cated hole in the Press Frame Upright (59) and
secure it with a 1/4” Flat Washer (11) and a 1/4”
Nylon Locknut (16).
11
59
13
16
Secure the other end of the Press Backrest (89) with a
1/4” x 2 1/2” Screw (10) and a 1/4” Flat Washer (11).
42
11
12
16
Download from Www.Somanuals.com. All Manuals Search And Download.
36. Insert a 1/4” x 1 1/2” Carriage Bolt (82) into the center
hole in a Seat Plate (42). Attach the Seat Plate to a
Seat (51) with two 1/4” x 3/4” Screws (13).
36
51
Insert the 1/4” x 1 1/2” Carriage Bolt (82) into the indi-
cated hole in the Seat Bar (74) and secure it with a
1/4” Flat Washer (11) and a 1/4” Nylon Locknut (16).
Secure the other end of the Seat (51) with a 1/4” x
1 1/2” Screw (88) and a 1/4” Flat Washer.
82
74
42
11
13
16
88
37. Attach the Backrest (66) to the Butterfly Upright (62)
with two 1/4” x 2 1/2” Screws (10) and two 1/4” Flat
Washers (11).
37
11
10
62
66
11
38. Attach the Curl Pad (69) to the Curl Post (70) with two
1/4” x 3/4” Screws (13).
38
69
70
Insert the Curl Post (70) into the Seat Brace (75) and
secure the Curl Post at the desired height with the
Adjustment Knob (45).
13
45
75
17
Download from Www.Somanuals.com. All Manuals Search And Download.
39. Apply the WEIDER PRO 9930 decal in the location
shown.
39
WEIDER
PRO 9930
40. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in
ADJUSTMENT, beginning on page 21 of this manual.
Before using the weight system, pull each cable a few times to make sure that the cables move smoothly
over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If
the cables are not properly installed, they may be damaged when heavy weight is used. See the
CABLE DIAGRAMS on pages 19 and 20 of this manual for proper cable routing. If there is any slack
in the cables, you will need to remove the slack by tightening the cables. See TROUBLE-SHOOTING
AND MAINTENANCE on page 22.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE DIAGRAMS
The cable diagrams below and on the next page show the proper routing of the Short Cable (71), the Medium
Cable (72), and the Long Cable (73). The numbers show the correct route for each Cable. Make sure that the
Cables are routed correctly, that the Pulleys move smoothly, and that the Cable Traps do not touch or
bind the Cables. Incorrect cable routing can damage the weight system.
Short Cable (71)
Medium Cable (72)
2
1
2
1
4
4
5
3
3
5
Cable ID Chart
(71) 1.9m (6 ft. 3 in.)
(72) 3.5m (11 ft. 6 in.)
(73) 7.6m (24 ft. 11 in.)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Long Cable (73)
6
3
10
5
7
4
8
9
13
2
1
12
11
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENT
The instructions below describe how each part of the weight system can be adjusted. Important: When using
an attachment, make sure that it is in the correct starting position for the exercise to be performed. If
there is any slack in the cables or the chain as an exercise is performed, the effectiveness of the exer-
cise will be reduced.
CHANGING THE WEIGHT SETTING
To change the setting of the weight stack, insert a Weight
Pin (87) under the desired Weight (8). Make sure you
insert the Weight Pin as far as it will go. Note: Due to the
cables and pulleys, the amount of resistance at each
exercise station may vary from the weight setting.
Use the WEIGHT RESISTANCE CHART on page 23 to
8
find the approximate amount of resistance at each
87
weight station.
ATTACHING THE LAT BAR OR NYLON STRAP TO
THE HIGH PULLEY STATION
72
57
56
Attach the Lat Bar (50) to the Medium Cable (72) with a
Cable Clip (57). For some exercises, the Chain (55)
should be attached between the Lat Bar and the Medium
Cable with two Cable Clips. Adjust the length of the
Chain between the Lat Bar and the Medium Cable so
the Lat Bar will be in the correct starting position for
the exercise to be performed.
55
50
The Nylon Strap (56) can be attached in the same manner.
ATTACHING THE LAT BAR OR NYLON STRAP TO
THE LOW PULLEY STATION
56
73
Attach the Lat Bar (50) to the Long Cable (73) with a
Cable Clip (57). For some exercises, the Chain (55)
should be attached between the Lat Bar and the Long
Cable with two Cable Clips. Adjust the length of the
Chain between the Lat Bar and the Long Cable so the
Lat Bar will be in the correct starting position for the
exercise to be performed.
55
57
The Nylon Strap (56) can be attached in the same manner.
USING THE CURL PAD
To use the Curl Pad (69), insert the Curl Post (70) into the
Seat Brace (75) and secure the Curl Post at the desired
height with the Adjustment Knob (45).
69
70
45
75
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-SHOOTING AND MAINTENANCE
Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately.
The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use sol-
vents.
TIGHTENING THE CABLES
The type of cable used on weight systems can stretch slightly when it is first used. If there is slack in the cables
before resistance is felt, the cables should be tightened. Slack can be removed from the cables in several differ-
ent ways:
Moving one or both of the 3 1/2” Pulleys (5) to a different
set of holes in the Adjustable Pulley Plates (44) will tight-
en the cables.
35
44
To move one of the 3 1/2” Pulleys (5), remove the 3/8”
Nylon Locknut (4), 3/8” x 2” Bolt (35), Cable Trap (39),
and Pulley from the Adjustable Pulley Plates (44). Re-
attach the Pulley and Cable Trap to the other hole in the
Pulley Plates. Note: If additional adjustment is need-
ed, move the other Pulley.
Adjustment
Holes
4
5
39
Slack can be removed from the Long Cable (73) by relo-
cating the indicated 3 1/2” Pulley (5) on the Press Seat
Frame (52). To do this, remove the 3/8” Nylon Locknut
(4), 3/8” Flat Washer (17), and 3/8” x 2 1/2” Bolt (6). Re-
attach the Pulley at the second or third hole, as needed.
52
4
17
5
14
73
6
The threaded shaft on the Medium Cable (72) attached to
the Weights (8) can also be used to tighten the cables.
72
To tighten the Medium Cable (72), remove the Small “U”-
Bracket (43) by removing the 5/16” Nylon Locknut (2) and
the 5/16” x 1 3/4” Bolt (9).
2
72
43
9
See the inset drawing. Tighten the 1/4” Nylon Locknut
(16) at the end of the Medium Cable (72) as far as it will
go. Then re-attach the Small “U”-Bracket (43).
8
16
43
If a cable slips off the pulleys often, the cable may have become twisted. Remove the cable and re-install
it. If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
WEIGHT RESISTANCE CHART
The chart below shows the approximate weight resistance at each exercise station. “Top” refers to the 6-lb. top
weight; the other numbers refer to the 12.5-lb. weight plates. Note: The actual resistance at each station may
vary due to differences in individual weight plates as well as friction between the cables, pulleys, and
weight guides.
High
Pulley
(lbs.)
Arm
Press
(lbs.)
Butterfly
(lbs.)
Curl/
Low Pulley
(lbs.)
Leg Raise
(lbs.)
Weight
Plates
Top
1
11
25
20
39
15
31
16
32
17
37
2
40
59
48
47
56
3
55
78
64
63
76
4
70
97
80
78
95
5
84
117
136
156
175
97
93
115
135
154
174
6
99
113
130
146
109
124
140
7
114
128
8
Note: 1 lb. = .454 kg.
PLACE
STAMP
HERE
ICON of Canada Inc.
900 de l’Industrie
St-Jérôme, Québec
Canada, J7Y 4B8
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-888-936-4266, Monday
through Friday, 8 a.m. until 6:30 p.m. EST (excluding holidays). To help us assist you, please be prepared to
give the following information:
1. The MODEL NUMBER of the product (WESY99300)
2. The NAME of the product (WEIDER® PRO 9930 weight system)
3. The SERIAL NUMBER of the product (see the front cover of this manual)
4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING
attached in the center of this manual).
™
®
o f / d u C a n a d a I n c .
PRODUCT WARRANTY REGISTRATION
IMPORTANT: MAIL WITHIN 14 DAYS OF PURCHASE
NAME:
ADDRESS:
COUNTY:
PHONE:
POSTCODE:
MODEL NO.
RETAILER NAME:
SERIAL NO.
PURCHASE DATE:
RETAILER ADDRESS:
1) Primary user(s) of product:
8) Did you consider purchasing fitness equipment from another
manufacturer?
o
Male
o
Female
o
Family
o No
o Yes
2) Age of primary user:
What other manufacturer?
o
0–24
o 35–44
o 45–54
o 55–64
o 65 and over
o 25–34
9) Based on your impression of what you have purchased,
would you buy another ICON product?
3) Annual household income:
o Yes
o No
o No opinion
o 0–9,999
o 10,000–14,999
o 15,000–19,999
o 20,000+
If not, what other brand of equipment would you purchase?
4) How many times a week do you exercise?
10) What other type of exercise equipment do you own?
o Less than 3 times o 3 times or more
o Bicycle
o Exercise cycle o Treadmill
o Weight bench o Stepper
o Other____________
o Home gym
o Cardio glide
5) Have you ever purchased an ICON product before?
o Yes o No
11) Which types of magazines do you read regularly?
6) Where did you first see or hear about ICON products?
o Sports
o Business
o Fitness
o Computer
o Motoring
o Other_____
o Magazine
o Newspaper ad
o Store
o Friend/relative
o Other_______________
12) Do you wish to be sent further bulletins about ICON products?
o Yes o No
7) What was the primary reason for purchasing this ICON product?
o Store employee o Television ads o Colour
o Electronic features o Magazine ads o Price
THANK YOU FOR YOUR TIME
o Product design
o Other____________
o Product innovation
© 2001 ICON of Canada, Inc. Printed in Canada
Part
No.
173978
R0501AP
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE THIS PART IDENTIFICATION
CHART FROM THE MANUAL
This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below
each part refers to the key number of the part. Important: Some parts may have been pre-assembled for
shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre-assembled.
Note: Assembly is divided into four stages: 1) frame assembly; 2) arm assembly; 3) cable and pulley
assembly; and 4) seat assembly. The hardware for each assembly stage is packaged separately. Wait
until you begin each stage to open the parts bag for that stage.
R0501A
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART–Model No. WESY99300
1/4" Flat Washer (11)
5/16" x 1 3/4" Bolt (9)
5/16" Flat Washer (19)
5/16" x 2 1/2" Bolt (3)
5/16" x 2 3/4" Bolt (20)
5/16" x 2 1/2" Carriage Bolt (1)
1/4" x 2" Bolt (86)
3/8" Flat Washer (17)
1/4" Nylon Locknut (16)
5/16" Nylon Locknut (2)
5/16" Jam Nut (90)
1/4" x 2" Carriage Bolt (85)
1/4" x 2 1/2" Carriage Bolt (12)
#10 x 1” Screw (32)
3/8" Nylon Locknut (4)
3/8" Jam Nut (18)
1/4" x 3/4" Screw (13)
1/4" x 2 1/2" Screw (10)
3/8” x 2 1/2” Eye Bolt (83)
Download from Www.Somanuals.com. All Manuals Search And Download.
1/4" x 1 1/2" Screw (88)
1/4" x 1 1/2" Carriage Bolt (82)
3/8" x 1" Bolt (15)
"V" Pulley (21)
(Not shown to scale)
3/8" x 1 3/4" Bolt (22)
3 1/2" Pulley (5)
(Not shown to scale)
3/8" x 2" Bolt (35)
4 1/2" Pulley (34)
(Not shown to scale)
3/8" x 2 1/4" Bolt (81)
3/8" x 2 1/2" Bolt (6)
Cable Clip (57)
3/8" x 3 1/4" Bolt (28)
3/8" x 3 1/2" Bolt (24)
3/8" x 3 3/4" Bolt (7)
1" Retainer (25)
3/8" x 4 3/4" Bolt (23)
Download from Www.Somanuals.com. All Manuals Search And Download.
3/4" Round Inner Cap (40)
1" x 7/8" Plastic Bushing (29)
1" Round Cap (26)
1" Round Inner Cap (41)
1" Inner Cap (80)
1 3/4" Square Inner Cap (37)
1 1/2" Square Inner Cap (79)
2" Square Inner Cap (38)
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE THIS PART LIST/EXPLODED
DRAWING FROM THE MANUAL
1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. WESY99300
R0501A
Key
No. Qty.
DescriptionKey
No. Qty.
Description
1
2
3
4
5
6
7
8
8
27
4
18
15
6
2
8
1
3
9
1
8
3
2
4
14
9
10
14
3
3
1
1
4
2
2
3
2
1
4
1
1
5/16” x 2 1/2” Carriage Bolt
5/16” Nylon Locknut
5/16” x 2 1/2” Bolt
3/8” Nylon Locknut
3 1/2” Pulley
3/8” x 2 1/2” Bolt
3/8” x 3 3/4” Bolt
Weight
5/16” x 1 3/4” Bolt
1/4” x 2 1/2” Screw
1/4” Flat Washer
1/4” x 2 1/2” Carriage Bolt
1/4” x 3/4” Screw
Long Cable Trap
3/8” x 1” Bolt
1/4” Nylon Locknut
3/8” Flat Washer
3/8” Jam Nut
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
#
4
2
1
1
2
1
1
2
1
1
4
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
3
2
1
1
1
2
1
1
1
1
1
1
1
Foam Pad
Pad Tube
Leg Lever
Lat Bar
Seat
Press Seat Frame
Press Frame
Press Arm
Chain
Nylon Strap
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Cable Clip
Weight Guide
Press Frame Upright
Press Base
Butterfly Base
Butterfly Upright
Press Top Frame
Butterfly Top Frame
10” Pad
5/16” Flat Washer
5/16” x 2 3/4” Bolt
“V” Pulley
3/8” x 1 3/4” Bolt
3/8” x 4 3/4” Bolt
3/8” x 3 1/2” Bolt
1” Retainer
Backrest
Left Butterfly Arm
Right Butterfly Arm
Curl Pad
Curl Post
Short Cable
Medium Cable
Long Cable
Seat Bar
1” Round Cap
1 1/8” x 2 1/2” Plastic Bushing
3/8” x 3 1/4” Bolt
1” x 7/8” Plastic Bushing
3/8” x 8” Bolt
Hand Grip
#10 x 1” Screw
Bumper
4 1/2” Pulley
3/8” x 2” Bolt
Double “U”-Bracket
1 3/4” Square Inner Cap
2” Square Inner Cap
Cable Trap
3/4” Round Inner Cap
1” Round Inner Cap
Seat Plate
Small “U”-Bracket
Adjustable Pulley Plate
Adjustment Knob
Top Plate
Seat Brace
Weight Tube Bumper
Weight Tube
Top Weight
1 1/2” Square Inner Cap
1” Inner Cap
5/16” x 2 1/4” Bolt
1/4” x 1 1/2” Carriage Bolt
3/8” x 2 1/2” Eyebolt
Weight Bumper
1/4” x 2” Carriage Bolt
1/4” x 2” Bolt
Weight Pin
1/4” x 1 1/2” Screw
Press Backrest
5/16” Jam Nut
User’s Manual
1
6
1
6
6
12
4
2
3
1
2
1
2
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. WESY99300
R0501A
Download from Www.Somanuals.com. All Manuals Search And Download.
|