R
ANALYZER X3 & X6
User’s Manual
W & W Manufacturing Co.
800 South Broadway
Hicksville, NY 11801
In USA & Canada: 800-221-0732
In N.Y. State: 516-942-0011
Fax: 516-942-1944
1 Ready 2 Read
4 Ready 5 testi
y
ng
3Ready
6 Chrg
E-Mail: [email protected]
3 MINUTE
BATTERY
ANALYZER
All specifications are subject to change without notice.
!
MADE IN
USA BY:
W & W Manufacturing Co.
Copyright Version 210.19.07.Rev.2
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Safety and Operating Environment
Always use a grounded AC outlet to power the Analyzer X3 & X6.
Keep the Analyzer X3 & X6 at least one-foot away from any object to allow for proper
ventilation.
Do not Analyze Batteries outside the recommended temperature ranges. For good and
consistent results, 25°C (Room temperature) is recommended. Allow batteries to stabilize to room
temperature before analyzing.
Do not exceed the battery manufacturer’s recommended voltage, charge current and
discharge current.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Universal cup
OVERVIEW
The Universal cup will allow one to evaluate batteries with different chemistries and cell counts within defined
specifications. The Universal cup has one memory location that can be programed the same as the Learn
Memory location in a standard cup.
During entry into the “Learn Mode”of the Universal cup, Battery Chemistry, Capacity, and the number of Cells
Are prompted for data entry. Follow the Directions below to enter data for the Learn Mode.
The W&W Analyzer X3& X6 is a programmable battery tester and battery cycler capable of testing a variety
of battery chemistries such as; Lithium Ion, Lithium Polymer, Nickel Cadmium and Nickel Metal Hydride.
Most mechanical shapes can be accommodated with a specially designed battery cup. See battery
Cup description for more information.
FEATURES
Data Range
Chemistry (Lithium Ion, Nickel Cadmium, and Nickel Metal Hydride)
Analyzes, condition and charges Nickel Cadmium and Nickel Metal Hydride batteries.
Analyzes and charge lithium Ion and lithium polymer batteries.
Features a single button capable of multifunction and an easy to read display for a user interface.
Auto condition cycle for nickel batteries and life cycle mode for all batteries.
Capacity 100 - 4000 maH
# Of Cells
1-12 NiCd and 1-4 Li-ion
SELECTING “ LEARN “ FOR
UNIVERSAL CUP
ACTION
Important: It is important that when testing
an UNKNOWN BATTERY in the learn mode that
you select the UNKNOWN state as opposed to
GOOD. You can not perform a valid Quick
test or an impedance test with the Universal cup.
One must observe the proper polarity when
connecting the battery to the Universal cup.
Should you connect the battery incorrectly,
you will hair a buzzing sound, reverse the leads.
*
EMPTY
Display After “Turn On”
Quick Test (QT), determines the state of a battery, as well as one of two states
Batt>60% and Batt<60%
EMPTY
PUSH BUTTON ONCE
NO ACTION
NO ACTION
PUSH
Prime mode, allows one to enable a Li-ion battery to be unlocked at the upper and lower end of
the Li-ion protective circuits range. Enabling Nickel based battery to acquire a charge to enable
the battery to be evaluated by the various modes of the X3 & X6.
INSERT BATTERY
LEARN MODE
SELECTED
Optional thermal printer for status and result printing.
At this point you may perform all the standard
operations that can be performed in stations; 2
3, 5 and 6 of the X3 and X6.
BATT STATUS: UNKNOWN OR GOOD
<FUNCTION> TO CHANGE
PC program available for more advance user interfacing and graph generation.
BATTERY TYPE =
LITHIUM ION
Embedded OEM parameters or user defined profiles in “Learn Mode”.
PUSH
PUSH
To change the cup settings for a different battery
or for different parameters for the same battery,
just repeat the Learn mod process again.
SELECTED CAPACITY =
1800 MAHR
CELL COUNT =
2 CELLS
PUSH
ENTER THE NEW CHARGE
RATE: 1000 MA
PUSH
PUSH
PUSH
PASS / FAIL LEVEL =
80% OF CAPACITY
.
ENTER NEW DIS -CHRG
RATE: C/2
LION 1CELL 1800MAH
CHRG: 1000MA C /:2
NO ACTION
NO ACTION
PUSH
STORING NEW
CONFIGURATION
READY
Universal cup.
LEARN MODE COMPLETE
REMOVE BATTERY
REMOVE BATTERY
4
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Learn Mode
X3 & X6 Specifications
Station
This mode when selected will allow a battery’s parameters to be created for new battery models.
A battery “Adapter Cup” holds a total of 5 battery profiles for parameter storage; four are preprogrammed
with OEM information for a particular battery series. The fifth profile can be modified by the “Learn
Mode”. During entry into the “Learn Mode”, Battery Chemistry, Capacity, and the number of Cells are
prompted for data entry. Follow the Directions below to enter data for the Learn Mode.
Std Power Supply Hi Power Supply
X3 X6
3
6
Number of stations
QuickTest:
Stations
#1
#1 & 4
Data Range
Chemistry (Lithium Ion, Nickel Cadmium, and Nickel Metal Hydride)
Takes approximately 3min.
Checks Impedance
Capacity 100 - 4000 maH
# Of Cells
Checks voltage min/max
Checks discharge at different rates
Utilizes an algorithm to determine capacity range.
1-12 NiCd and 1-4 Li-ion
SELECTING “ LEARN “
AND RESULTS
ACTION
Important: It is important that when testing
an UNKNOWN BATTERY in the learn mode that
you select the UNKNOWN state as opposed to
the GOOD state until the battery has been
certified to be equal to or greater than 95% of
it’s rated capacity, then perform an Impedance
test and record the results, repeat the learn
mode with: BATT STATUS: as GOOD. Once a
good battery is learned, you will be able to
perform a QUICK TEST in station (1) of the X3
and on stations (1) and (4) of the X6.
Stations
Standard Tests:
*
3
3
3
3
3
1
6
Charge only
Discharge onl y
Cycle : 1 , 2 , 3
Auto
Condition
Impedance
6
EMPTY
Display After “Turn On”
6
6
6
EMPTY
PUSH BUTTON ONCE
NO ACTION
NO ACTION
PUSH
1 & 4
INSERT BATTERY
Battery Voltage : 1.2 to 15V
Max. Number of cells: Nickel based : 12 cells, Li-ion: 4 cells
Charge/Discharge current: 50mA to 4A in 50mA steps
LEARN MODE
SELECTED
Maximum charge power :
X3
X6
55W/station, 60W total
55W/station, 120W total
58W/station,100W totaL
58W/station, 200W total
BATT STATUS: UNKNOWN OR GOOD
<FUNCTION> TO CHANGE
*
Maximum Discharge power:
X3
X6
25W/station, 75W total
25W/station, 150W total
25W/station, 75W total
25W/station 150W total
Learn Mode Precautions
BATTERY TYPE =
LITHIUM ION
.
PUSH
PUSH
A good battery must be used to calibrate a
battery’s profile. OEM batteries have unique
profiles that should not be used when testing
non-OEM batteries. For each new non-OEM
battery, create a new profile. The factory
settings can not be modified in the field,
however by utilizing the LEARN MODE
function one can learn a non-OEM battery.
It is very important that the battery you are
using the LEARN MODE function for must be
at least 95% of the stated capacity and a
Impedance test should be performed on
the battery in question and entered when
requested in the LEARN MODE. It is a good
idea to set the acceptable deviation to
35% to begin with. The learning of a good
non-OEM battery will enable you to perform
a QUICK TEST (QT) in station #1 of the X3 and
stations #(1) and #(4) of the X6.
Power Management: The X3 & X6 automatically regulates which station will receive max. Power during high pwr demands.
SELECTED CAPACITY =
1800 MAHR
Chemistries: Lion, NiCD and NiMH
CELL COUNT =
2 CELLS
PUSH
Charge and End of Charge Detection Protocols:
Li -ion, Constant current - Constant voltage Detection is achieved at C/11. Where (C) = capacity of Batt.
Nickel based battery: Constant current, with negative delta V Detection.
*
ENTER THE NEW CHARGE
RATE: 1000 MA
PUSH
PUSH
PUSH
Display: 20x2 Backlit LCD
PASS / FAIL LEVEL =
80% OF CAPACITY
Batter y Adapters:
Quick Connect Adapter Cups for ease of changing Adapters (No tools required)
Five Memory locations, each can be programmed for Li-ion, NiCD or NiMH
Fifth memory location is field programmable, for all parameters
ENTER NEW DIS -CHRG
RATE: C/2
Data Ports:RS-232 interface to P.C. And Serial Printer
NOMINAL IMPEDANCE = **
**
PUSH
PUSH
250 mOHMS
Line Voltage:
Input Current:
100 TO 240 VAC 50 to 60 Hz
2 A
ACCEPT DEVIATION =
35%
Output:
X3
X3
X6
X6
LION 1CELL 1800MAH
CHRG: 1000MA C /:2
NO ACTION
NO ACTION
PUSH
Dimensions and Weight:
Length
Width
h
Dept
Weight
4.5”(110.25mm)
13”(318.5mm)
9”(220.5mm)
6.5lb(2.96kg)
Length
Width
h
Dept
Weight
4.5”(110.25mm)
24.5”(622.3mm)
9”(220.5mm)
STORING NEW
CONFIGURATION
11.3lb(5.2kg)
READY
Options Available:
LEARN MODE COMPLETE
REMOVE BATTERY
070217 All Specifications are subject to change without notice.
REMOVE BATTERY
(**) APPEARS ONLY WHEN A (GOOD) BATTERY IS BEING LEARNED!
16
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Overview
Impedance Test
Impedance of a battery can be a good indicator of degradation of a battery’s performance. In general, the lower
the impedance number the better the battery performance during discharge. As a battery ages the
impedance starts to rise indicating possible problems with the electrolyte, separator, contact corrosion, or
metal interfaces, all impact the impedance.
The initial impedance of a new battery should be recorded and compared through the life of a battery and a
determination can be made to remove the battery from service when the impedance rises out of range.
The Analyzer X3 and X6 produce impedance results within a 15 seconds of testing and displays the impedance in
Ohms on the display or on a printout when an optional printer is used.
Adapter cups
Follow the directions below for Impedance testing.
Printer Port
This test is only performed in Pocket #1 for the X3 and pockets #1 and #4 for the X6.
2
1
EMPTY
EMPTY
3
EMPTY
SELECTING “IMPEDANCE “
AND RESULTS
ACTION
EMPTY
Display After “Turn On”
DISPLAY
Analyzer X3
TO PROCEED PRESS
<FUNCTION>
FUNCTION BUTTONS
After the battery is placed
in the adapter
PUSH FUNCTION BUTTON
until battery
specs appear
NICD 700 MAH 7.2V
<FUNCTION> FOR NEXT
in the display
NICD 700 MAH 7.2V
HAS BEEN SELECTED
NO ACTION
PUSH
QUICK TEST
<FUNCTION> FOR NEXT
On/Off Switch
Power in Receptacle
CYCLE/AUTO/CONDITION
<FUNCTION> FOR NEXT
PUSH
PUSH
Serial Port
(Computer) DB9-female
Serial Port
(Printer) DB9-Male
DIS -CHRG BATTERY
<FUNCTION> FOR NEXT
CHARGE BATTERY
<FUNCTION> FOR NEXT
PUSH
Rear view of Analyzer X3
Hi Power in Receptacle
optional
IMPEDANCE TEST
<FUNCTION> FOR NEXT
NO ACTION
IMPEDANCE TEST
HAS BEEN SELECTED
On/Off Switch
Power in Receptacle
NO ACTION
TESTING
READY
NO ACTION
FOR RESULTS PUSH
BATTERY IMPEDANCE
.233 ohms
PUSH
Serial Port
(Computer) DB9-female
Serial Port
(Printer) DB9-Male
Rear view of Analyzer X6
15
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Charge Mode
Understanding the Analyzer X3’s and X6’s Adapter CUP
The Analyzer X3 and X6 applies two types of charge algorithms for the two types of chemistries.
For Nickel based battery chemistries, a constant current of 1C (changeable with software option) is applied
until the battery voltage peaks and descends negative. A top off current or 0.2C is then applied for 30
minutes to bring the total charge to 100%.
The “Adapter Cup” allow different batteries to be serviced by the Analyzer X3 and X6.
Each “Adapter Cup” is made for a specific battery model. There are 5 memory locations
(data profile locations) within each “Adapter Cup”. The first four profiles store pre-stored
battery information and can only be altered using an optional software interface. The type
of data stored for example is chemistry (NiCD, NiMH, Lithium Ion and Lithium Polymer),
capacity, impedance, charge current, and discharge current.
The fifth profile location is used for a user defined battery type or the same OEM model.
To invoke this location and store data, use the “Learn Mode”. See the Section on “Learn
Mode” in order to enter data.
Lithium batteries are charged with a different algorithm. The Analyzer X3 and X6 applies a constant current of
1C until the battery pack voltage equals between 4.1 and 4.2 Volts (the exact voltage depends on the pack
manufacturer’s specification). Upon reaching the predetermined voltage, the voltage is then held constant
allowing the current to decrease to C/11.
The rate at which the battery is charging is called a C rate. The (C) rate is the charging current divided by the
Capacity of the battery . For example: the capacity of a battery is 1200maH and the charge current is
1200 mA, than (C) rate is 1(C). If the charge current is reduced to 120 mA, then the C rate is 0.1C.
To select the Analyzer X3’s and X6’s Charge Mode, follow the directions below:
Highlighted Features
SELECTING “ CHARGE “
RESULTS
ACTION
Physically accommodates battery pack in the analyzer
Holds five different Muti -chemistry parameter profiles.
Learn Mode profile location for user defined parameters of a unique battery.
Locking Latch system allows cups to be changed without tools.
EMPTY
Display After “Turn On”
UP to 4 OEM battery pack’s profiles programmed at factory
TO PROCEED PRESS
<FUNCTION>
After the battery is placed
in the adapter
Prime mode, allows the unlocking of a Li-ion Battery protection
circuits, both at the upper and lower limits. The Prime mode will
also put a charge on a nickle based battery that has been
allowed to self discharge to a level that the X3 or the X6 or a battery charger
could not recognize it when the battery is placed in a charger or the
X3 or X6.
PUSH FUNCTION BUTTON
until battery
specs appear
LION 1650 MAH 7.4V
<FUNCTION> FOR NEXT
in the display
LION 1650 MAH 7.4V
HAS BEEN SELECTED
NO ACTION
PUSH
QUICK TEST
<FUNCTION> FOR NEXT
CYCLE/AUTO/CONDITION
<FUNCTION> FOR NEXT
PUSH
DISCHARGE BATTERY
<FUNCTION> FOR NEXT
PUSH
CHARGE BATTERY
<FUNCTION> FOR NEXT
NO ACTION
NO ACTION
CHARGE BATTERY
HAS BEEN SELECTED
CHARGING
READY
NO ACTION
NO ACTION
Adapter cup
CHARGE COMPLETED
120 MINUTES + TOP OFF
FOR RESULTS
PUSH
14
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Discharge Mode
Getting Started
The Analyzer X3 and X6 is capable of a single discharge cycle by selecting Discharge Mode.
In the normal discharge mode a constant pre-stored load current (C/5) is applied to the battery until 1volt
per cell has been reached. The result of the measurement is displayed as a percent of capacity. The
capacity of a battery is defined as the amount of current over time. So the discharge result shown by the
Analyzer X3 and the X6 is also given in mAh, the amount of current discharged over time.
The rate at which the battery is discharge is called the (C) rate. 1C is the discharge current amount of the
battery divided by battery capacity. For example: the capacity of a battery is 1200mAh and the discharge
current is 1200 mA, 1C. If the discharge current is reduced to 120 mA, then the C rate is 0.1C.
Power Up
- Connect the unit to the proper AC voltage and
Turn-on power using the switch located on the
Back of the unit.
ONCE THE UNIT HAS BEEN
POWERED, THE DISPLAY
SHOULD SHOW, AND THEN SHOW
WW Manufacturing
V3.20P Date: 2.09.03
Use the following procedure to select the Discharge mode:
2
X3
X6
1
EMPTY
EMPTY
SELECTING “ DISCHARGE “
RESULTS
3
EMPTY
3
6
1
4
2
5
ACTION
EMPTY
EMPTY
EMPTY
EMPTY
EMPTY
EMPTY
EMPTY
Display After “Turn On”
TO PROCEED PRESS
<FUNCTION>
You are now ready to service a bat.tery. Placing the appropriate “adapter cup” in the analyzer will allow
you to service an OEM battery. The cup contains pre-stored data e.g. chemistry type, capacity, impedance,
charge rate and discharge rate for 4 battery types.
There is a fifth data position in the “cup” reserved for user defined information during the Learn Mode.
See “Learn Mode” for more information.
After the battery is placed
in the adapter
PUSH FUNCTION BUTTON
until battery
specs appear
LION 1650 MAH 7.4V
<FUNCTION> FOR NEXT
in the display
1. Place a battery into the “adapter cup”. The display “Press Function to Proceed” should be displayed.
LION 1650 MAH 7.4V
HAS BEEN SELECTED
NO ACTION
PUSH
The analyzer should detect your battery and give chemistry and capacity options as the function button is
Pushed. See note below, should the aforementioned not occur. *
QUICK TEST
<FUNCTION> FOR NEXT
*Note: If you do not see your chemistry during this process, remove the battery and reinsert it after pressing
the function button momentarily. This operation will place you in the “Learn Mode”. See “Learn Mode” on how
To proceed.
CYCLE/AUTO/CONDITION
<FUNCTION> FOR NEXT
PUSH
2. Scroll through the menu until your battery appears (using the Function Button). When your battery
appears, stop pressing the Function Button and wait until the display stop blinking. An acknowledgement
beep will be heard and the display will also acknowledge your selection.
DIS-CHRG BATTERY
<FUNCTION> FOR NEXT
NO ACTION
NO ACTION
3. The display will now show a menu of “Test options”as you press the function button e.g. QUICK TEST,
CYCLE/AUTO/CONDITION, Dis-charge, Charge and Impedance Test. This sequence only occurs for Station (1).
For Stations (2) and (3) you will see the following sequence: CYCLE/AUTO/CONDITION, DIS-CHRG BATTERY
and CHARGE BATTERY
DIS-CHRG BATTERY
HAS BEEN SELECTED
DIS-CHRG
READY
NO ACTION
NO ACTION
As you press the Function button the display should scroll through the menu of “Tests”. When the test you
have select appears in the display, just simply stop pressing the function button and wait until the display
stop blinking. Once the display stops blinking, an acknowledgement beep will be heard along with a visual
of the test you Selected in the display.
4. The test you selected will now start. Results will be displayed upon completion and if you have the
optional printer attached a print out will also be printed upon test completion.
DIS-CHRG BATTERY
CAP= 91% 1501MAH
FOR RESULTS
PUSH
13
8
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK TEST ANALYSIS
Condition Mode
The CONDITION CYCLE serves basically two needs of Nickel based batteries, one is to reform the
This is an advanced proprietary algorithm capable of determining the health of a battery. Specially stored
parameters allowing the Analyzer X3 or X6 to identify a battery’s range of capacity and display: Batt>60% or
Batt<60%of rated capacity . Batteries that have a low state of charge when placed in the X3 for the QT
May require a charge of up to 10 minutes before performing the QT. Up to 3 attempts to charge the battery
will be tried before a message is displayed “Discard the Battery”.
Even batteries that do not have pre-stored parameters can have a QT on, but will first be required to go
through the “ Learn Mode”. Note, first a good battery must be learned before QT can be performed .
A impedance test must be performed prior to the “Learn Mode”, and incorporated into the LEARN MODE.
Cells of a battery that hasn’t been used for an extended period of time, say for 3 or more Months.
Secondly this mode will eliminate MEMORY EFFECT better known as VOLTAGE DEPRESSION.
Usually deep discharging the battery will restore the battery back to normal capacity such as the discharging
and charging cycle used in the Analyzer X3 and X6.
Lithium Ion batteries do not suffer from voltage depression, but they will not be harmed if the Conditioning
cycle is applied to them. To select the condition cycle follow the instructions below.
With the X3 and X6, the percentage of the rated capacity of the battery being CONDITIONED is set at 80%, the 80%
is set at the factory and can be modified with the use of optional software.
SELECTING “ CONDITION “
AND RESULTS
SELECTING “ QUICK TEST “
RESULTS
ACTION
ACTION
DISPLAY
EMPTY
EMPTY
Display After “Turn On”
Display After “Turn On”
TO PROCEED PRESS
<FUNCTION>
After the battery is placed
in the adapter
PUSH FUNCTION BUTTON
until battery
specs appear
NICD 700 MAH 7.2V
<FUNCTION> FOR NEXT
TO PROCEED PRESS
<FUNCTION>
After the battery is placed
in the adapter
in the display
NICD 700 MAH 7.2V
HAS BEEN SELECTED
NO ACTION
PUSH
PUSH FUNCTION BUTTON
until battery
specs appear
LION 1650 MAH 7.4V
<FUNCTION> FOR NEXT
QUICK TEST
<FUNCTION> FOR NEXT
in the display
CYCLE/AUTO/CONDITION
<FUNCTION> FOR NEXT
LION 1650 MAH 7.4V
HAS BEEN SELECTED
NO ACTION
NO ACTION
PUSH
NO ACTION
CYCLE/AUTO/CONDITION
HAS BEEN SELECTED
QUICK TEST
<FUNCTION> FOR NEXT
CYCLE 1
<FUNCTION> FOR NEXT
NO ACTION
NO ACTION
CONDITION TO 80%
<FUNCTION> FOR NEXT
QUICK TEST
HAS BEEN SELECTED
NO ACTION
NO ACTION
NO ACTION
NO ACTION
CONDITION TO 80%
HAS BEEN SELECTED
TEST
NO ACTION
TESTING
READY
FOR RESULTS
PUSH
READY
CONDITION - DONE 1
CAP= 85% 595 MAH
PUSH
FOR RESULTS
QUICK TEST ANALYSIS
BATT>60% 0R BATT<60%
REMOVE BATTERY
9
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Cycle Mode
Auto Mode
The Cycle mode will cycle a battery through a charge and discharge cycle, known as Cycle (1). One could
Select, Cycle 1, 2 or 3. By selecting cycle 1,2 or 3 all one would be doing is repeating the Charge/discharge
number to reflect the chosen Cycle count. Cycle 2 and 3 are often used for incoming quality control of new batteries.
The X3 will display the capacity (in percentage of rated capacity and mAH). It should be noted that after the
Life cycle testing can be accomplished by choosing the Auto test. Battery performance for multiple cycles can be
evaluated as long as the battery is not removed. Charge and discharge cycles are performed with 10-minute
rest in between charge and discharge.
An example of how this test can be used is the following: A manufacturer states that a NiMH battery will
Achieve a % of the stated capacity through the 300 cycles through its life (life can be defined as 300 cycles).
The 300 cycles can be verified provided that the discharge rate is adjusted per the manufacturer’s specifications.
completion of the Cycle function the battery is left in a fully charged state.
SELECTING “ CYCLE 2 “
RESULTS
SELECTING “ AUTO “
RESULTS
ACTION
ACTION
EMPTY
Display After “Turn On”
EMPTY
Display After “Turn On”
TO PROCEED PRESS
<FUNCTION>
TO PROCEED PRESS
<FUNCTION>
After the battery is placed
in the adapter
After the battery is placed
in the adapter
PUSH FUNCTION BUTTON
until battery
specs appear
PUSH FUNCTION BUTTON
until battery
specs appear
NICD 700 MAH 7.2V
<FUNCTION> FOR NEXT
NICD 700 MAH 7.2V
<FUNCTION> FOR NEXT
in the display
in the display
NICD 700 MAH 7.2V
HAS BEEN SELECTED
NICD 700 MAH 7.2V
HAS BEEN SELECTED
NO ACTION
PUSH
NO ACTION
PUSH
QUICK TEST
<FUNCTION> FOR NEXT
QUICK TEST
<FUNCTION> FOR NEXT
CYCLE/AUTO/CONDITION
<FUNCTION> FOR NEXT
CYCLE/AUTO/CONDITION
<FUNCTION> FOR NEXT
NO ACTION
NO ACTION
PUSH
NO ACTION
NO ACTION
CYCLE/AUTO/CONDITION
HAS BEEN SELECTED
CYCLE/AUTO/CONDITION
HAS NEEN SELECTED
CYCLE 1
<FUNCTION> FOR NEXT
CYCLE 2
<FUNCTION> FOR NEXT
PUSH
AUTO CYCLE
<FUNCTION> FOR NEXT
CYCLE 2
HAS BEEN SELECTED
NO ACTION
NO ACTION
NO ACTION
NO ACTION
AUTO CYCLE
HAS BEEN SELECTED
TESTING
READY
NO ACTION
NO ACTION
TESTING
THE ACTUAL READING WHEN YOU PRESS THE FUNCTION
BUTTON WILL DEPEND ON WHERE IN THE CYCLE YOU ARE.
IT IS FOR THIS REASON WE RECOMMEND PERFORMING
THIS TEST WITH A SERIAL PRINTER
CYCLE 2
CAP=88% 616 MAH
FOR RESULTS PUSH
AUTO CYCLE - PASS 45
CAP= 85% 595 MAH
PUSH
FOR RESULTS
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|