.
.
Vandal-proof Tamper Detection PoE
Quick Installation Guide
ᖅϛ ᙏϛ Рҏᇭ
Italiano Türkçe
Русский Česky Svenska
English
Français Español
Deutsch
Português
Polski
FD7130
This guide describes the basic functions of FD7130
All detailed information is described in the user's manual.
IP Surveillance
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not place the Network Camera
on unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
EN - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Package Contents
Liquid Tight Connectors for
RJ45 or M12 Cable
FD7130 with an RJ45 or M12 Cable
RJ45
RJ45
M12
Alignment Sticker
Software CD
Quick Installation Guide /
Warranty Card
Ground Wire / Screws
Screwdriver
Silica Gel
EN - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Physical Description
Inner View
Screw Holes
Lens
MicroSD/SDHC Card Slot
Status LED
Temperature Alarm
The alarm will be triggered
once the temparature inside the
Network Camera reaches 60°C.
Reset Button
Outer View
Record the MAC address
before installing the camera.
Network Camera
Model No: FD7130
MAC:0002D107258A
RoHS
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Pat. 6,930,709
Made in Taiwan
Waterproof Level: IP66
EN - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Cabling Assembly
RJ45 Cable Connector
RJ45 Cable Dimension (unit: mm)
Components of the Waterproof
Connector
Sealing Nut (A)
Seal (B)
Screw Nut (C)
Housing (D)
Gasket (E)
Assembling Steps
2
Insert the housing into the
screw nut.
3
Insert the seal into the housing.
1
Prepare an Ethernet cable
and strip part of the sheath.
(C)
(D)
(B)
Recommended cable gauge: 24AWG
(0.51 mm)
Insert the stripped Ethernet
cable through the sealing
nut and the housing.
4
5
6
Push the RJ45 plug into the
housing, then secure the
sealing nut tightly.
Clamp the cable with
an RJ45 plug.
(A)
7
Attach the gasket to the front
of the housing.
8
Connect the Ethernet cable to the RJ45 cable
and secure the connectors tightly.
(E)
EN - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
M12 Cable Connector
M12 Cable Dimension (unit: mm)
Components of the Waterproof
Connector
Sealing Nut (A)
Seal (B)
Clamp Ring (C)
Gasket (D)
Plastic Nut (E)
Assembling Steps
1
3
Insert the gasket into the clamp
ring.
2
Prepare an Ethernet cable
and strip part of the sheath.
Insert the seal into the clamp
ring.
(C)
(B)
(D)
Ø4.5mm~Ø6.5mm
Insert the stripped Ethernet
cable through the sealing nut
and the clamp ring.
Follow the pin definition in the below table
to solder the stripped Ethernet cable to the
plastic nut.
4
5
(E)
(A)
Follow the pin definition in the below table
to connect the Ethernet cable to the M12
cable and secure them tightly.
6
Secure the sealing nut to the
clamp ring tightly.
7
Ethernet Cable /
M12 Cable
Wire Color
Ethernet Cable
M12 Cable
1
2
3
4
5
6
7
8
Orange/White
Orange
Green/White
Blue
Blue/White
Brown/White
Brown
Green
EN - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Hardware Installation
First, use the supplied screwdriver to detach the dome cover from the camera base. Insert your
MicroSD/SDHC Card if necessary.
Tamper-proof Screw
Dome Cover
Rubber Stopper
Camera Base
Then, follow the steps below to install the camera to either the ceiling or the wall:
1. Attach the supplied alignment sticker to the ceiling/wall.
2. Using the 3 screw circles on the sticker, drill 3 pilot holes into the ceiling/wall. Then hammer the
plastic anchors into the holes.
3. This Network Camera can be mounted with the cable routed through the camera base or from
the side of the dome cover. If you want to feed the cable through the ceiling/wall, please also
cut or drill a hole (A) for the cable. If the cable goes through the side of the dome cover, please
remove the rubber stopper (B).
4. Through the 3 holes on the camera base, insert the screws to corresponding holes and secure
the camera base with a screwdriver.
Ceiling Mount
A
1
2
3
4
A
B
EN - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall Mount
1
2
B
A
3
4
Please secure the screws tightly to
avoid moisture.
Installing the Ground Wire
As shown in the following figure, please secure one side of the supplied ground wire to the screw
hole, then route the other side of the ground wire to the ground.
EN - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Deployment
5
Power over Ethernet (PoE)
When using a PoE-enabled switch
This Network Camera is PoE-compliant, allowing transmission of power and data via a single
Ethernet cable. Follow the below illustration to connect the camera to a PoE-enabled switch via
Ethernet cable.
PoE Switch
LINK
P
OWE
R
C
OLLI
S
ION
R
E
C
E
IV
E
ITION
1
2
P
AR
3
T
4
5
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE
switch.
PoE Power Injector
(optional)
L
INK
P
O
W
E
R
C
O
L
L
IS
IO
R
E
N
C
E
IV
IT
E
N
1
2
3
P
AR
T
4
5
IO
Non-PoE Switch
EN - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Assigning an IP Address
1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network is ana-
lyzed, please click on the “Next” button to continue the program.
Installation
Wizard 2
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras
on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches the one
labeled on the bottom of your device to connect to the Network Camera via Internet Explorer.
Network Camera
00-02-D1-07-25-8A
192.168.5.151
FD7130
Model No: FD7130
0002D107258A
MAC:0002D107258A
RoHS
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Pat. 6,930,709
Made in Taiwan
Download from Www.SomanuEalsN.co-m1.0All Manuals Search And Download.
7
Ready to Use
1. Access the Network Camera on the LAN.
2. Retrieve live video through a web browser or recording software.
For further setup, please refer to the user's manual on the software CD.
Adjusting the Lens
8
To adjust the viewing angle
Adjust the lens to a desired viewing angle as the diagram shown below.
10°
90°
10°
DO NOT over rotate the lens. Doing
so will damage the camera lens
module.
EN - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Fine-tune the Camera Focus
The focus of this network camera is set from 1.0m to infinity by factory default. If you want to focus
on objects closer than 1.0m or the lens has lost focus, please fine tune it in the following way.
1. Loosen the lens lock screw.
2. Manually rotate the lens to fine-tune the focus
until the live image is clear.
3. Tighten the lens lock screw.
Tighten the lens lock screw.
Completion
9
Tear down the aluminum foil vacuum bag and take out the silica gel. Attach the supplied silica gel to
the inner side of the Network Camera. (Please replace the silica gel with a new one if you open the
back cover after installation.)
Attach the dome cover to camera. Secure the dome screws with the supplied screwdriver. Finally,
make sure all parts of the camera are securely installed.
Please secure the screws tightly to
prevent the cabling against moisture.
Download from Www.SomanuEalsN.co-m1.2All Manuals Search And Download.
P/N: 625008801G Ver.1.1
2009 VIVOTEK INC. All right reserved.
Copyright
Download from Www.Somanuals.com. All Manuals Search And Download.
|